Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc/android driver fixes for 6.18-rc3 for
reported issues. Included in here are:
- rust binder fixes for reported issues
- mei device id addition
- mei driver fixes
- comedi bugfix
- most usb driver bugfixes
- fastrpc memory leak fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
most: usb: hdm_probe: Fix calling put_device() before device initialization
most: usb: Fix use-after-free in hdm_disconnect
binder: remove "invalid inc weak" check
mei: txe: fix initialization order
comedi: fix divide-by-zero in comedi_buf_munge()
mei: late_bind: Fix -Wincompatible-function-pointer-types-strict
misc: fastrpc: Fix dma_buf object leak in fastrpc_map_lookup
mei: me: add wildcat lake P DID
misc: amd-sbi: Clarify that this is a BMC driver
nvmem: rcar-efuse: add missing MODULE_DEVICE_TABLE
binder: Fix missing kernel-doc entries in binder.c
rust_binder: report freeze notification only when fully frozen
rust_binder: don't delete FreezeListener if there are pending duplicates
rust_binder: freeze_notif_done should resend if wrong state
rust_binder: remove warning about orphan mappings
rust_binder: clean `clippy::mem_replace_with_default` warning
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for the gpib subsystem to
resolve some reported issues. Included in here are:
- memory leak fixes
- error code fixes
- proper protocol fixes
All of these have been in linux-next for almost 2 weeks now with no
reported issues"
* tag 'staging-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: gpib: Fix device reference leak in fmh_gpib driver
staging: gpib: Return -EINTR on device clear
staging: gpib: Fix sending clear and trigger events
staging: gpib: Fix no EOI on 1 and 2 byte writes
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for reported issues.
Included in here are:
- sh-sci serial driver fixes
- 8250_dw and _mtk driver fixes
- sc16is7xx driver bugfix
- new 8250_exar device ids added
All of these have been in linux-next this past week with no reported
issues"
* tag 'tty-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_mtk: Enable baud clock and manage in runtime PM
serial: 8250_dw: handle reset control deassert error
dt-bindings: serial: sh-sci: Fix r8a78000 interrupts
serial: sc16is7xx: remove useless enable of enhanced features
serial: 8250_exar: add support for Advantech 2 port card with Device ID 0x0018
tty: serial: sh-sci: fix RSCI FIFO overrun handling
Pull USB driver fixes from Greg KH:
"Here are some small USB driver fixes and new device ids for 6.18-rc3.
Included in here are:
- new option serial driver device ids added
- dt bindings fixes for numerous platforms
- xhci bugfixes for many reported regressions
- usbio dependency bugfix
- dwc3 driver fix
- raw-gadget bugfix
All of these have been in linux-next this week with no reported issues"
* tag 'usb-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Telit FN920C04 ECM compositions
USB: serial: option: add Quectel RG255C
tcpm: switch check for role_sw device with fw_node
usb/core/quirks: Add Huawei ME906S to wakeup quirk
usb: raw-gadget: do not limit transfer length
USB: serial: option: add UNISOC UIS7720
xhci: dbc: enable back DbC in resume if it was enabled before suspend
xhci: dbc: fix bogus 1024 byte prefix if ttyDBC read races with stall event
usb: xhci-pci: Fix USB2-only root hub registration
dt-bindings: usb: qcom,snps-dwc3: Fix bindings for X1E80100
usb: misc: Add x86 dependency for Intel USBIO driver
dt-bindings: usb: switch: split out ports definition
usb: dwc3: Don't call clk_bulk_disable_unprepare() twice
dt-bindings: usb: dwc3-imx8mp: dma-range is required only for imx8mp
Pull x86 fixes from Borislav Petkov:
- Remove dead code leftovers after a recent mitigations cleanup which
fail a Clang build
- Make sure a Retbleed mitigation message is printed only when
necessary
- Correct the last Zen1 microcode revision for which Entrysign sha256
check is needed
- Fix a NULL ptr deref when mounting the resctrl fs on a system which
supports assignable counters but where L3 total and local bandwidth
monitoring has been disabled at boot
* tag 'x86_urgent_for_v6.18_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Remove dead code which might prevent from building
x86/bugs: Qualify RETBLEED_INTEL_MSG
x86/microcode: Fix Entrysign revision check for Zen1/Naples
x86,fs/resctrl: Fix NULL pointer dereference with events force-disabled in mbm_event mode
Pull irq fixes from Borislav Petkov:
- Restore the original buslock locking in a couple of places in the irq
core subsystem after a rework
* tag 'irq_urgent_for_v6.18_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/manage: Add buslock back in to enable_irq()
genirq/manage: Add buslock back in to __disable_irq_nosync()
genirq/chip: Add buslock back in to irq_set_handler()
Pull objtool fixes from Borislav Petkov:
- Fix x32 build due to wrong format specifier on that sub-arch
- Add one more Rust noreturn function to objtool's list
* tag 'objtool_urgent_for_v6.18_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix failure when being compiled on x32 system
objtool/rust: add one more `noreturn` Rust function
Pull scheduler fix from Borislav Petkov:
- Make sure a CFS runqueue on a throttled hierarchy has its PELT clock
throttled otherwise task movement and manipulation would lead to
dangling cfs_rq references and an eventual crash
* tag 'sched_urgent_for_v6.18_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Start a cfs_rq on throttled hierarchy with PELT clock throttled
Pull timer fix from Borislav Petkov:
- Do not create more than eight (max supported) AUX clocks sysfs
hierarchies
* tag 'timers_urgent_for_v6.18_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix aux clocks sysfs initialization loop bound
Pull driver core fixes from Danilo Krummrich:
- In Device::parent(), do not make any assumptions on the device
context of the parent device
- Check visibility before changing ownership of a sysfs attribute
group
- In topology_parse_cpu_capacity(), replace an incorrect usage of
PTR_ERR_OR_ZERO() with IS_ERR_OR_NULL()
- In devcoredump, fix a circular locking dependency between
struct devcd_entry::mutex and kernfs
- Do not warn about a pending fw_devlink sync state
* tag 'driver-core-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
arch_topology: Fix incorrect error check in topology_parse_cpu_capacity()
rust: device: fix device context of Device::parent()
sysfs: check visibility before changing group attribute ownership
devcoredump: Fix circular locking dependency with devcd->mutex.
driver core: fw_devlink: Don't warn about sync_state() pending
Pull firewire fixes from Takashi Sakamoto:
"A small collection of FireWire fixes. This includes corrections to
sparse and API documentation"
* tag 'firewire-fixes-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: init_ohci1394_dma: add missing function parameter documentation
firewire: core: fix __must_hold() annotation
Pull RISC-V fixes from Paul Walmsley:
- Close a race during boot between userspace vDSO usage and some
late-initialized vDSO data
- Improve performance on systems with non-CPU-cache-coherent
DMA-capable peripherals by enabling write combining on
pgprot_dmacoherent() allocations
- Add human-readable detail for RISC-V IPI tracing
- Provide more information to zsmalloc on 64-bit RISC-V to improve
allocation
- Silence useless boot messages about CPUs that have been disabled in
DT
- Resolve some compiler and smatch warnings and remove a redundant
macro
* tag 'riscv-for-linus-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: hwprobe: avoid uninitialized variable use in hwprobe_arch_id()
riscv: cpufeature: avoid uninitialized variable in has_thead_homogeneous_vlenb()
riscv: hwprobe: Fix stale vDSO data for late-initialized keys at boot
riscv: add a forward declaration for cpuinfo_op
RISC-V: Don't print details of CPUs disabled in DT
riscv: Remove the PER_CPU_OFFSET_SHIFT macro
riscv: mm: Define MAX_POSSIBLE_PHYSMEM_BITS for zsmalloc
riscv: Register IPI IRQs with unique names
ACPI: RIMT: Fix unused function warnings when CONFIG_IOMMU_API is disabled
RISC-V: Define pgprot_dmacoherent() for non-coherent devices
Pull xfs fixes from Carlos Maiolino:
"The main highlight here is a fix for a bug brought in by the removal
of attr2 mount option, where some installations might actually have
'attr2' explicitly configured in fstab preventing system to boot by
not being able to remount the rootfs as RW.
Besides that there are a couple fix to the zonefs implementation,
changing XFS_ONLINE_SCRUB_STATS to depend on DEBUG_FS (was select
before), and some other minor changes"
* tag 'xfs-fixes-6.18-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix locking in xchk_nlinks_collect_dir
xfs: loudly complain about defunct mount options
xfs: always warn about deprecated mount options
xfs: don't set bt_nr_sectors to a negative number
xfs: don't use __GFP_NOFAIL in xfs_init_fs_context
xfs: cache open zone in inode->i_private
xfs: avoid busy loops in GCD
xfs: XFS_ONLINE_SCRUB_STATS should depend on DEBUG_FS
xfs: do not tightly pack-write large files
xfs: Improve CONFIG_XFS_RT Kconfig help
Pull smb server fixes from Steve French:
"smbdirect (RDMA) fixes in order avoid potential submission queue
overflows:
- free transport teardown fix
- credit related fixes (five server related, one client related)"
* tag 'v6.18-rc2-smb-server-fixes' of git://git.samba.org/ksmbd:
smb: server: let free_transport() wait for SMBDIRECT_SOCKET_DISCONNECTED
smb: client: make use of smbdirect_socket.send_io.lcredits.*
smb: server: make use of smbdirect_socket.send_io.lcredits.*
smb: server: simplify sibling_list handling in smb_direct_flush_send_list/send_done
smb: server: smb_direct_disconnect_rdma_connection() already wakes all waiters on error
smb: smbdirect: introduce smbdirect_socket.send_io.lcredits.*
smb: server: allocate enough space for RW WRs and ib_drain_qp()
Clang is not happy with set but unused variable (this is visible
with `make W=1` build:
kernel/sched/sched.h:3744:18: error: variable 'cpumask' set but not used [-Werror,-Wunused-but-set-variable]
It seems like the variable was never used along with the assignment
that does not have side effects as far as I can see. Remove those
altogether.
Fixes: 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm fixes from Simona Vetter:
"Very quiet, all just small stuff and nothing scary pending to my
knowledge:
- drm_panic: bunch of size calculation fixes
- pantor: fix kernel panic on partial gpu va unmap
- rockchip: hdmi hotplug setup fix
- amdgpu: dp mst, dc/display fixes
- i915: fix panic structure leak
- xe: madvise uapi fix, wq alloc error, vma flag handling fix"
* tag 'drm-fixes-2025-10-24' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe: Check return value of GGTT workqueue allocation
drm/amd/display: use GFP_NOWAIT for allocation in interrupt handler
drm/amd/display: increase max link count and fix link->enc NULL pointer access
drm/amd/display: Fix NULL pointer dereference
drm/panic: Fix 24bit pixel crossing page boundaries
drm/panic: Fix divide by 0 if the screen width < font width
drm/panic: Fix kmsg text drawing rectangle
drm/panic: Fix qr_code, ensure vmargin is positive
drm/panic: Fix overlap between qr code and logo
drm/panic: Fix drawing the logo on a small narrow screen
drm/xe/uapi: Hide the madvise autoreset behind a VM_BIND flag
drm/xe: Retain vma flags when recreating and splitting vmas for madvise
drm/i915/panic: fix panic structure allocation memory leak
drm/panthor: Fix kernel panic on partial unmap of a GPU VA region
drm/rockchip: dw_hdmi: use correct SCLIN mask for RK3228
Pull pci fixes from Bjorn Helgaas:
- Add DWC custom pci_ops for the root bus instead of overwriting the
DBI base address, which broke drivers that rely on the DBI address
for iATU programming; fixes an FU740 probe regression (Krishna
Chaitanya Chundru)
- Revert qcom ECAM enablement, which is rendered unnecessary by the DWC
custom pci_ops (Krishna Chaitanya Chundru)
- Fix longstanding MIPS Malta resource registration issues to avoid
exposing them when the next commit fixes the boot failure (Maciej W.
Rozycki)
- Use pcibios_align_resource() on MIPS Malta to fix boot failure caused
by using the generic pci_enable_resources() (Ilpo Järvinen)
- Enable only ASPM L0s and L1, not L1 PM Substates, for devicetree
platforms because we lack information required to configure L1
Substates; fixes regressions on powerpc and rockchip. A qcom
regression (L1 Substates no longer enabled) remains and will be
addressed next (Bjorn Helgaas)
* tag 'pci-v6.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/ASPM: Enable only L0s and L1 for devicetree platforms
MIPS: Malta: Use pcibios_align_resource() to block io range
MIPS: Malta: Fix PCI southbridge legacy resource reservations
MIPS: Malta: Fix keyboard resource preventing i8042 driver from registering
Revert "PCI: qcom: Prepare for the DWC ECAM enablement"
PCI: dwc: Use custom pci_ops for root bus DBI vs ECAM config access
Add missing kernel-doc parameter descriptions for five functions
in init_ohci1394_dma.c to fix documentation warnings when building
with W=1.
This patch addresses the following warnings:
- init_ohci1394_wait_for_busresets: missing @ohci description
- init_ohci1394_enable_physical_dma: missing @ohci description
- init_ohci1394_reset_and_init_dma: missing @ohci description
- init_ohci1394_controller: missing @num, @slot, @func descriptions
- setup_ohci1394_dma: missing @opt description
Tested with GCC 13.2.0 and W=1 flag. All documentation warnings
for these functions have been resolved.
Signed-off-by: Nirbhay Sharma <nirbhay.lkd@gmail.com>
Link: https://lore.kernel.org/r/20251024203219.101990-2-nirbhay.lkd@gmail.com
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Pull crypto library fix from Eric Biggers:
"Avoid some false-positive KMSAN warnings by restoring the dependency
of the architecture-optimized Poly1305 code on !KMSAN"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: poly1305: Restore dependency of arch code on !KMSAN
Pull smb client fixes from Steve French:
- add missing tracepoints
- smbdirect (RDMA) fix
- fix potential issue with credits underflow
- rename fix
- improvement to calc_signature and additional cleanup patch
* tag '6.18-rc2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: #include cifsglob.h before trace.h to allow structs in tracepoints
cifs: Call the calc_signature functions directly
smb: client: get rid of d_drop() in cifs_do_rename()
cifs: Fix TCP_Server_Info::credits to be signed
cifs: Add a couple of missing smb3_rw_credits tracepoints
smb: client: allocate enough space for MR WRs and ib_drain_qp()
Pull block fixes from Jens Axboe:
- Fix dma alignment for PI
- Fix selinux bogosity with nbd, where sendmsg would get rejected
* tag 'block-6.18-20251023' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
block: require LBA dma_alignment when using PI
nbd: override creds to kernel when calling sock_{send,recv}msg()
Pull io_uring fixes from Jens Axboe:
- Add MAINTAINERS entry for zcrx, mostly so that netdev gets
automatically CC'ed by default on any changes there too.
- Fix for the SQPOLL busy vs work time accounting.
It was using getrusage(), which was both broken from a thread point
of view (we only care about the SQPOLL thread itself), and vastly
overkill as only the systime was used. On top of that, also be a bit
smarter in when it's queried. It used excessive CPU before this
change. Marked for stable as well.
- Fix provided ring buffer auto commit for uring_cmd.
- Fix a few style issues and sparse annotation for a lock.
* tag 'io_uring-6.18-20251023' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring: fix buffer auto-commit for multishot uring_cmd
io_uring: correct __must_hold annotation in io_install_fixed_file
io_uring zcrx: add MAINTAINERS entry
io_uring: Fix code indentation error
io_uring/sqpoll: be smarter on when to update the stime usage
io_uring/sqpoll: switch away from getrusage() for CPU accounting
io_uring: fix incorrect unlikely() usage in io_waitid_prep()
Pull slab fixes from Vlastimil Babka:
- Two fixes for race conditions in obj_exts allocation (Hao Ge)
- Fix for slab accounting imbalance due to deferred slab decativation
(Vlastimil Babka)
* tag 'slab-for-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: Fix obj_ext mistakenly considered NULL due to race condition
slab: fix slab accounting imbalance due to defer_deactivate_slab()
slab: Avoid race on slab->obj_exts in alloc_slab_obj_exts
Pull devicetree fixes from Rob Herring:
- Fix handling of GICv5 ITS MSI properties on platforms with
'msi-parent' as well as a of_node refcounting fix.
This is also preparation for further refactoring in 6.19 to use
common DT parsing of MSI properties.
* tag 'devicetree-fixes-for-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/irq: Export of_msi_xlate() for module usage
of/irq: Fix OF node refcount in of_msi_get_domain()
of/irq: Add msi-parent check to of_msi_xlate()
Pull SoC fixes from Arnd Bergmann:
"The main change this time is an update to the MAINTAINERS file,
listing Krzysztof Kozlowski, Alexandre Belloni, and Linus Walleij as
additional maintainers for the SoC tree, in order to go back to a
group maintainership. Drew Fustini joins as an additional reviewer for
the SoC tree.
Thanks to all of you for volunteering to help out.
On the actual bugfixes, we have a few correctness changes for firmware
drivers (qtee, arm-ffa, scmi) and two devicetree fixes for Raspberry
Pi"
* tag 'soc-fixes-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: officially expand maintainership team
firmware: arm_scmi: Fix premature SCMI_XFER_FLAG_IS_RAW clearing in raw mode
firmware: arm_scmi: Skip RAW initialization on failure
include: trace: Fix inflight count helper on failed initialization
firmware: arm_scmi: Account for failed debug initialization
ARM: dts: broadcom: rpi: Switch to V3D firmware clock
arm64: dts: broadcom: bcm2712: Define VGIC interrupt
firmware: arm_ffa: Add support for IMPDEF value in the memory access descriptor
tee: QCOMTEE should depend on ARCH_QCOM
tee: qcom: return -EFAULT instead of -EINVAL if copy_from_user() fails
tee: qcom: prevent potential off by one read
Pull spi fixes from Mark Brown:
"A moderately large collection of device specific changes here, mostly
fixes but also including a few new quirks and device IDs. This is all
fairly routine even for the affected devices"
* tag 'spi-fix-v6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: spi-rockchip: Add RK3506 compatible
spi: intel-pci: Add support for Intel Wildcat Lake SPI serial flash
spi: intel-pci: Add support for Arrow Lake-H SPI serial flash
spi: intel: Add support for 128M component density
spi: airoha: fix reading/writing of flashes with more than one plane per lun
spi: airoha: switch back to non-dma mode in the case of error
spi: airoha: add support of dual/quad wires spi modes to exec_op() handler
spi: airoha: return an error for continuous mode dirmap creation cases
spi: amlogic: fix spifc build error
spi: cadence-quadspi: Fix pm_runtime unbalance on dma EPROBE_DEFER
spi: spi-nxp-fspi: limit the clock rate for different sample clock source selection
spi: spi-nxp-fspi: add extra delay after dll locked
spi: spi-nxp-fspi: re-config the clock rate when operation require new clock rate
spi: dw-mmio: add error handling for reset_control_deassert()
spi: rockchip-sfc: Fix DMA-API usage
spi: dt-bindings: cadence: add soc-specific compatible strings for zynqmp and versal-net
Pull gpio fixes from Bartosz Golaszewski:
- fix regressions in regmap cache initialization in gpio-104-idio-16
and gpio-pci-idio-16
- configure first 16 GPIO lines of the IDIO-16 as fixed outputs
- fix duplicated IRQ mapping that can lead to an RCU stall in gpio-ljca
- fix printf formatters passed to dev_err() and make failure to set
debounce period non fatal
* tag 'gpio-fixes-for-v6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ljca: Fix duplicated IRQ mapping
gpiolib: acpi: Use %pe when passing an error pointer to dev_err()
gpiolib: acpi: Make set debounce errors non fatal
gpio: idio-16: Define fixed direction of the GPIO lines
gpio: regmap: add the .fixed_direction_output configuration parameter
gpio: pci-idio-16: Define maximum valid register address offset
gpio: 104-idio-16: Define maximum valid register address offset
Since Olof moved on from the soc tree maintenance, Arnd has mainly taken
care of the day-to-day activities around the SoC tree by himself, which
is generally not a good setup.
Krzysztof, Linus and Alexandre have volunteered to become co-maintainers
of the SoC tree, with the plan of taking turns to do merges and reviews
to spread the workload. In addition, Drew joins as another reviewer.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Johan writes:
USB serial device ids for 6.18-rc3
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.18-rc3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 ECM compositions
USB: serial: option: add Quectel RG255C
USB: serial: option: add UNISOC UIS7720
If two competing threads enter alloc_slab_obj_exts(), and the one that
allocates the vector wins the cmpxchg(), the other thread that failed
allocation mistakenly assumes that slab->obj_exts is still empty due to
its own allocation failure. This will then trigger warnings with
CONFIG_MEM_ALLOC_PROFILING_DEBUG checks in the subsequent free path.
Therefore, let's check the result of cmpxchg() to see if marking the
allocation as failed was successful. If it wasn't, check whether the
winning side has succeeded its allocation (it might have been also
marking it as failed) and if yes, return success.
Suggested-by: Harry Yoo <harry.yoo@oracle.com>
Fixes: f7381b9116 ("slab: mark slab->obj_exts allocation failures unconditionally")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Link: https://patch.msgid.link/20251023143313.1327968-1-hao.ge@linux.dev
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
We should wait for the rdma_cm to become SMBDIRECT_SOCKET_DISCONNECTED!
At least on the client side (with similar code)
wait_event_interruptible() often returns with -ERESTARTSYS instead of
waiting for SMBDIRECT_SOCKET_DISCONNECTED.
We should use wait_event() here too, which makes the code be identical
in client and server, which will help when moving to common functions.
Fixes: b31606097d ("smb: server: move smb_direct_disconnect_rdma_work() into free_transport()")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Commit 620a50c927 ("io_uring: uring_cmd: add multishot support") added
multishot uring_cmd support with explicit buffer upfront commit via
io_uring_mshot_cmd_post_cqe(). However, the buffer selection path in
io_ring_buffer_select() was auto-committing buffers for non-pollable files,
which conflicts with uring_cmd's explicit upfront commit model.
This way consumes the whole selected buffer immediately, and causes
failure on the following buffer selection.
Fix this by checking uring_cmd to identify operations that handle buffer
commit explicitly, and skip auto-commit for these operations.
Cc: Caleb Sander Mateos <csander@purestorage.com>
Fixes: 620a50c927 ("io_uring: uring_cmd: add multishot support")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark has been kindly helping fill in when I have been unavailable over
the past several years. He has also put his hand up to take over
linux-next maintenance when I finally decide to stop (which may be some
time yet ;-) ).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull tracing fixes from Steven Rostedt:
"A couple of fixes for Runtime Verification:
- A bug caused a kernel panic when reading enabled_monitors was
reported.
Change callback functions to always use list_head iterators and by
doing so, fix the wrong pointer that was leading to the panic.
- The rtapp/pagefault monitor relies on the MMU to be present
(pagefaults exist) but that was not enforced via kconfig, leading
to potential build errors on systems without an MMU.
Add that kconfig dependency"
* tag 'trace-rv-v6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
rv: Make rtapp/pagefault monitor depends on CONFIG_MMU
rv: Fully convert enabled_monitors to use list_head as iterator
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 6.18, please pull the following:
- Peter describes the VGIC interrupt line such that KVM can be used on
Raspberry Pi 5 systems.
* tag 'arm-soc/for-6.18/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm2712: Define VGIC interrupt
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
6.18, please pull the following:
- Stefan switches the V3D block to use the firmware clock, rather than
the bare metal clock. This fixes hangs on boot after recent changes to
the V3D driver clocking went in.
* tag 'arm-soc/for-6.18/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: broadcom: rpi: Switch to V3D firmware clock
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arm SCMI fixes for v6.18
This series contains a set of small, focused fixes that address
robustness and lifecycle issues in the Arm SCMI core and debug support,
ensuring safer handling of debug initialization failures, correct flag
management in raw mode, and consistent inflight counter tracking.
Brief summary:
- Fix raw xfer flag clearing
- Skip RAW debug initialization on failure
- Make inflight counter helpers null-safe, preventing crashes if debug
initialization fails
- Account for failed debug initialization globally
There is no functional change for standard SCMI operation, but these
fixes improve stability in debug and raw modes, particularly in error
paths.
* tag 'scmi-fixes-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix premature SCMI_XFER_FLAG_IS_RAW clearing in raw mode
firmware: arm_scmi: Skip RAW initialization on failure
include: trace: Fix inflight count helper on failed initialization
firmware: arm_scmi: Account for failed debug initialization
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arm FF-A fix for v6.18
The FF-A driver was updated to support specification version 1.2 but omitted
support for the 16-byte implementation-defined (IMPDEF) field introduced in
FF-A v1.2 within the Endpoint Memory Access Descriptor (EMAD). This omission
breaks all memory interfaces.
This change updates the EMAD sizing and offset logic to correctly handle the
FF-A v1.2 layout while preserving backward compatibility with older versions.
* tag 'ffa-fix-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Add support for IMPDEF value in the memory access descriptor
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull arm64 fixes from Catalin Marinas:
- Do not make a clean PTE dirty in pte_mkwrite()
The Arm architecture, for backwards compatibility reasons (ARMv8.0
before in-hardware dirty bit management - DBM), uses the PTE_RDONLY
bit to mean !dirty while the PTE_WRITE bit means DBM enabled. The
arm64 pte_mkwrite() simply clears the PTE_RDONLY bit and this
inadvertently makes the PTE pte_hw_dirty(). Most places making a PTE
writable also invoke pte_mkdirty() but do_swap_page() does not and we
end up with dirty, freshly swapped in, writeable pages.
- Do not warn if the destination page is already MTE-tagged in
copy_highpage()
In the majority of the cases, a destination page copied into is
freshly allocated without the PG_mte_tagged flag set. However, the
folio migration may be restarted if __folio_migrate_mapping() failed,
triggering the benign WARN_ON_ONCE().
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mte: Do not warn if the page is already tagged in copy_highpage()
arm64, mm: avoid always making PTE dirty in pte_mkwrite()
Pull networking fixes from Jakub Kicinski:
"Including fixes from can. Slim pickings, I'm guessing people haven't
really started testing.
Current release - new code bugs:
- eth: mlx5e:
- psp: avoid 'accel' NULL pointer dereference
- skip PPHCR register query for FEC histogram if not supported
Previous releases - regressions:
- bonding: update the slave array for broadcast mode
- rtnetlink: re-allow deleting FDB entries in user namespace
- eth: dpaa2: fix the pointer passed to PTR_ALIGN on Tx path
Previous releases - always broken:
- can: drop skb on xmit if device is in listen-only mode
- gro: clear skb_shinfo(skb)->hwtstamps in napi_reuse_skb()
- eth: mlx5e
- RX, fix generating skb from non-linear xdp_buff if program
trims frags
- make devcom init failures non-fatal, fix races with IPSec
Misc:
- some documentation formatting 'fixes'"
* tag 'net-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net/mlx5: Fix IPsec cleanup over MPV device
net/mlx5: Refactor devcom to return NULL on failure
net/mlx5e: Skip PPHCR register query if not supported by the device
net/mlx5: Add PPHCR to PCAM supported registers mask
virtio-net: zero unused hash fields
net: phy: micrel: always set shared->phydev for LAN8814
vsock: fix lock inversion in vsock_assign_transport()
ovpn: use datagram_poll_queue for socket readiness in TCP
espintcp: use datagram_poll_queue for socket readiness
net: datagram: introduce datagram_poll_queue for custom receive queues
net: bonding: fix possible peer notify event loss or dup issue
net: hsr: prevent creation of HSR device with slaves from another netns
sctp: avoid NULL dereference when chunk data buffer is missing
ptp: ocp: Fix typo using index 1 instead of i in SMA initialization loop
net: ravb: Ensure memory write completes before ringing TX doorbell
net: ravb: Enforce descriptor type ordering
net: hibmcge: select FIXED_PHY
net: dlink: use dev_kfree_skb_any instead of dev_kfree_skb
Documentation: networking: ax25: update the mailing list info.
net: gro_cells: fix lock imbalance in gro_cells_receive()
...
Pull ACPI fixes from Rafael Wysocki:
"These fix a fallout of a recent ACPI properties management update and
work around a compiler bug in ACPICA:
- Fix a recent coding mistake causing __acpi_node_get_property_reference()
arguments to be put in an incorrect order (Sunil V L)
- Work around bogus -Wstringop-overread warning on LoongArch since
GCC 11 in ACPICA (Xi Ruoyao)"
* tag 'acpi-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Work around bogus -Wstringop-overread warning since GCC 11
ACPI: property: Fix argument order in __acpi_node_get_property_reference()
Pull power management fixes from Rafael Wysocki:
"These revert a cpuidle menu governor commit leading to a performance
regression, fix an amd-pstate driver regression introduced recently,
and fix new conditional guard definitions for runtime PM.
- Add missing _RET == 0 condition to recently introduced conditional
guard definitions for runtime PM (Rafael Wysocki)
- Revert a cpuidle menu governor change that introduced a serious
performance regression on Chromebooks with Intel Jasper Lake
processors (Rafael Wysocki)
- Fix an amd-pstate driver regression leading to EPP=0 after
hibernation (Mario Limonciello)"
* tag 'pm-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: runtime: Fix conditional guard definitions
Revert "cpuidle: menu: Avoid discarding useful information"
cpufreq/amd-pstate: Fix a regression leading to EPP 0 after hibernate
Pull btrfs fixes from David Sterba:
- in send, fix duplicated rmdir operations when using extrefs
(hardlinks), receive can fail with ENOENT
- fixup of error check when reading extent root in ref-verify and
damaged roots are allowed by mount option (found by smatch)
- fix freeing partially initialized fs info (found by syzkaller)
- fix use-after-free when printing ref_tracking status of delayed
inodes
* tag 'for-6.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: ref-verify: fix IS_ERR() vs NULL check in btrfs_build_ref_tree()
btrfs: fix delayed_node ref_tracker use after free
btrfs: send: fix duplicated rmdir operations when using extrefs
btrfs: directly free partially initialized fs_info in btrfs_check_leaked_roots()
Since commit af92793e52 ("slab: Introduce kmalloc_nolock() and
kfree_nolock().") there's a possibility in alloc_single_from_new_slab()
that we discard the newly allocated slab if we can't spin and we fail to
trylock. As a result we don't perform inc_slabs_node() later in the
function. Instead we perform a deferred deactivate_slab() which can
either put the unacounted slab on partial list, or discard it
immediately while performing dec_slabs_node(). Either way will cause an
accounting imbalance.
Fix this by not marking the slab as frozen, and using free_slab()
instead of deactivate_slab() for non-frozen slabs in
free_deferred_objects(). For CONFIG_SLUB_TINY, that's the only possible
case. By not using discard_slab() we avoid dec_slabs_node().
Fixes: af92793e52 ("slab: Introduce kmalloc_nolock() and kfree_nolock().")
Link: https://patch.msgid.link/20251023-fix-slab-accounting-v2-1-0e62d50986ea@suse.cz
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported a potential lock inversion deadlock between
vsock_register_mutex and sk_lock-AF_VSOCK when vsock_linger() is called.
The issue was introduced by commit 687aa0c558 ("vsock: Fix
transport_* TOCTOU") which added vsock_register_mutex locking in
vsock_assign_transport() around the transport->release() call, that can
call vsock_linger(). vsock_assign_transport() can be called with sk_lock
held. vsock_linger() calls sk_wait_event() that temporarily releases and
re-acquires sk_lock. During this window, if another thread hold
vsock_register_mutex while trying to acquire sk_lock, a circular
dependency is created.
Fix this by releasing vsock_register_mutex before calling
transport->release() and vsock_deassign_transport(). This is safe
because we don't need to hold vsock_register_mutex while releasing the
old transport, and we ensure the new transport won't disappear by
obtaining a module reference first via try_module_get().
Reported-by: syzbot+10e35716f8e4929681fa@syzkaller.appspotmail.com
Tested-by: syzbot+10e35716f8e4929681fa@syzkaller.appspotmail.com
Fixes: 687aa0c558 ("vsock: Fix transport_* TOCTOU")
Cc: mhal@rbox.co
Cc: stable@vger.kernel.org
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20251021121718.137668-1-sgarzare@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ralf Lici says:
====================
fix poll behaviour for TCP-based tunnel protocols
This patch series introduces a polling function for datagram-style
sockets that operates on custom skb queues, and updates ovpn (the
OpenVPN data-channel offload module) and espintcp (the TCP Encapsulation
of IKE and IPsec Packets implementation) to use it accordingly.
Protocols like the aforementioned one decapsulate packets received over
TCP and deliver userspace-bound data through a separate skb queue, not
the standard sk_receive_queue. Previously, both relied on
datagram_poll(), which would signal readiness based on non-userspace
packets, leading to misleading poll results and unnecessary recv
attempts in userspace.
Patch 1 introduces datagram_poll_queue(), a variant of datagram_poll()
that accepts an explicit receive queue. This builds on the approach
introduced in commit b50b058, which extended other skb-related functions
to support custom queues. Patch 2 and 3 update espintcp_poll() and
ovpn_tcp_poll() respectively to use this helper, ensuring readiness is
only signaled when userspace data is available.
Each patch is self-contained and the ovpn one includes rationale and
lifecycle enforcement where appropriate.
====================
Link: https://patch.msgid.link/20251021100942.195010-1-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
openvpn TCP encapsulation uses a custom queue to deliver packets to
userspace. Currently it relies on datagram_poll, which checks
sk_receive_queue, leading to false readiness signals when that queue
contains non-userspace packets.
Switch ovpn_tcp_poll to use datagram_poll_queue with the peer's
user_queue, ensuring poll only signals readiness when userspace data is
actually available. Also refactor ovpn_tcp_poll in order to enforce the
assumption we can make on the lifetime of ovpn_sock and peer.
Fixes: 11851cbd60 ("ovpn: implement TCP transport")
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20251021100942.195010-4-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
espintcp uses a custom queue (ike_queue) to deliver packets to
userspace. The polling logic relies on datagram_poll, which checks
sk_receive_queue, which can lead to false readiness signals when that
queue contains non-userspace packets.
Switch espintcp_poll to use datagram_poll_queue with ike_queue, ensuring
poll only signals readiness when userspace data is actually available.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20251021100942.195010-3-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some protocols using TCP encapsulation (e.g., espintcp, openvpn) deliver
userspace-bound packets through a custom skb queue rather than the
standard sk_receive_queue.
Introduce datagram_poll_queue that accepts an explicit receive queue,
and convert datagram_poll into a wrapper around datagram_poll_queue.
This allows protocols with custom skb queues to reuse the core polling
logic without relying on sk_receive_queue.
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Antonio Quartulli <antonio@openvpn.net>
Link: https://patch.msgid.link/20251021100942.195010-2-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The __must_hold annotation references &req->ctx->uring_lock, but req
is not in scope in io_install_fixed_file. This change updates the
annotation to reference the correct ctx->uring_lock.
improving code clarity.
Fixes: f110ed8498 ("io_uring: split out fixed file installation and removal")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The generic_handle_domain_irq() function resolves the hardware IRQ
internally. The driver performed a duplicative mapping by calling
irq_find_mapping() first, which could lead to an RCU stall.
Delete the redundant irq_find_mapping() call and pass the hardware IRQ
directly to generic_handle_domain_irq().
Fixes: c5a4b6fd31 ("gpio: Add support for Intel LJCA USB GPIO driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20251023070231.1305-1-vulab@iscas.ac.cn
[Bartosz: remove unused variable]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Merge an ACPI device properties handling change fixing the order of
__acpi_node_get_property_reference() arguments broken by a recent
update (Sunil V L)
* 'acpi-property':
ACPI: property: Fix argument order in __acpi_node_get_property_reference()
Merge cpuidle and cpufreq fixes for 6.18-rc3:
- Revert a cpuidle menu governor change that introduced a serious
performance regression on Chromebooks with Intel Jasper Lake
processors (Rafael Wysocki)
- Fix an amd-pstate driver regression leading to EPP=0 after
hibernation (Mario Limonciello)
* pm-cpuidle:
Revert "cpuidle: menu: Avoid discarding useful information"
* pm-cpufreq:
cpufreq/amd-pstate: Fix a regression leading to EPP 0 after hibernate
If the send_peer_notif counter and the peer event notify are not synchronized.
It may cause problems such as the loss or dup of peer notify event.
Before this patch:
- If should_notify_peers is true and the lock for send_peer_notif-- fails, peer
event may be sent again in next mii_monitor loop, because should_notify_peers
is still true.
- If should_notify_peers is true and the lock for send_peer_notif-- succeeded,
but the lock for peer event fails, the peer event will be lost.
This patch locks the RTNL for send_peer_notif, events, and commit simultaneously.
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Cc: Jay Vosburgh <jv@jvosburgh.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Vincent Bernat <vincent@bernat.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251021050933.46412-1-tonghao@bamaicloud.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
intel-gpio fixes for v6.18-1
* Make set debounce errors non-fatal in GPIO ACPI case
* Use human readable error when printing a message in GPIO ACPI code
Make cifs #include cifsglob.h in advance of #including trace.h so that the
structures defined in cifsglob.h can be accessed directly by the cifs
tracepoints rather than the callers having to manually pass in the bits and
pieces.
This should allow the tracepoints to be made more efficient to use as well
as easier to read in the code.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Paulo Alcantara <pc@manguebit.org>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
There is no need to force a lookup by unhashing the moved dentry after
successfully renaming the file on server. The file metadata will be
re-fetched from server, if necessary, in the next call to
->d_revalidate() anyways.
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: stable@vger.kernel.org
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Commit 16c07342b5 ("gpiolib: acpi: Program debounce when finding GPIO")
adds a gpio_set_debounce_timeout() call to acpi_find_gpio() and makes
acpi_find_gpio() fail if this fails.
But gpio_set_debounce_timeout() failing is a somewhat normal occurrence,
since not all debounce values are supported on all GPIO/pinctrl chips.
Making this an error for example break getting the card-detect GPIO for
the micro-sd slot found on many Bay Trail tablets, breaking support for
the micro-sd slot on these tablets.
acpi_request_own_gpiod() already treats gpio_set_debounce_timeout()
failures as non-fatal, just warning about them.
Add a acpi_gpio_set_debounce_timeout() helper which wraps
gpio_set_debounce_timeout() and warns on failures and replace both existing
gpio_set_debounce_timeout() calls with the helper.
Since the helper only warns on failures this fixes the card-detect issue.
Fixes: 16c07342b5 ("gpiolib: acpi: Program debounce when finding GPIO")
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <superm1@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/stable/20250920201200.20611-1-hansg%40kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
HSR/PRP driver does not handle correctly having slaves/interlink devices
in a different net namespace. Currently, it is possible to create a HSR
link in a different net namespace than the slaves/interlink with the
following command:
ip link add hsr0 netns hsr-ns type hsr slave1 eth1 slave2 eth2
As there is no use-case on supporting this scenario, enforce that HSR
device link matches netns defined by IFLA_LINK_NETNSID.
The iproute2 command mentioned above will throw the following error:
Error: hsr: HSR slaves/interlink must be on the same net namespace than HSR link.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20251020135533.9373-1-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
chunk->skb pointer is dereferenced in the if-block where it's supposed
to be NULL only.
chunk->skb can only be NULL if chunk->head_skb is not. Check for frag_list
instead and do it just before replacing chunk->skb. We're sure that
otherwise chunk->skb is non-NULL because of outer if() condition.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://patch.msgid.link/20251021130034.6333-1-bigalex934@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix TCP_Server_Info::credits to be signed, just as echo_credits and
oplock_credits are. This also fixes what ought to get at least a
compilation warning if not an outright error in *get_credits_field() as a
pointer to the unsigned server->credits field is passed back as a pointer
to a signed int.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-cifs@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Acked-by: Pavel Shilovskiy <pshilovskiy@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Lad Prabhakar says:
====================
net: ravb: Fix SoC-specific configuration and descriptor handling issues [part]
This series addresses several issues in the Renesas Ethernet AVB (ravb)
driver related descriptor ordering.
A potential ordering hazard in descriptor setup could cause
the DMA engine to start prematurely, leading to TX stalls on some
platforms.
The series includes the following changes:
Enforce descriptor type ordering to prevent early DMA start
Ensure proper write ordering of TX descriptor type fields to prevent the
DMA engine from observing an incomplete descriptor chain. This fixes
observed TX stalls on RZ/G2L platforms running RT kernels.
Tested on R/G1x Gen2, RZ/G2x Gen3 and RZ/G2L family hardware.
====================
Link: https://patch.msgid.link/20251017151830.171062-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure the TX descriptor type fields are published in a safe order so the
DMA engine never begins processing a descriptor chain before all descriptor
fields are fully initialised.
For multi-descriptor transmits the driver writes DT_FEND into the last
descriptor and DT_FSTART into the first. The DMA engine begins processing
when it observes DT_FSTART. Move the dma_wmb() barrier so it executes
immediately after DT_FEND and immediately before writing DT_FSTART
(and before DT_FSINGLE in the single-descriptor case). This guarantees
that all prior CPU writes to the descriptor memory are visible to the
device before DT_FSTART is seen.
This avoids a situation where compiler/CPU reordering could publish
DT_FSTART ahead of DT_FEND or other descriptor fields, allowing the DMA to
start on a partially initialised chain and causing corrupted transmissions
or TX timeouts. Such a failure was observed on RZ/G2L with an RT kernel as
transmit queue timeouts and device resets.
Fixes: 2f45d1902a ("ravb: minimize TX data copying")
Cc: stable@vger.kernel.org
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251017151830.171062-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes the logic to prevent on overflow of
the send submission queue with ib_post_send() easier.
As we first get a local credit and then a remote credit
before we mark us as pending.
For now we'll keep the logic around smbdirect_socket.send_io.pending.*,
but that will likely change or be removed completely.
The server will get a similar logic soon, so
we'll be able to share the send code in future.
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
This introduces logic to prevent on overflow of
the send submission queue with ib_post_send() easier.
As we first get a local credit and then a remote credit
before we mark us as pending.
From reading the git history of the linux smbdirect
implementations in client and server) it was seen
that a peer granted more credits than we requested.
I guess that only happened because of bugs in our
implementation which was active as client and server.
I guess Windows won't do that.
So the local credits make sure we only use the amount
of credits we asked for.
Fixes: 0626e6641f ("cifsd: add server handler for central processing and tranport layers")
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
We have a list handling that is much easier to understand:
1. Before smb_direct_flush_send_list() is called all
struct smbdirect_send_io messages are part of
send_ctx->msg_list
2. Before smb_direct_flush_send_list() calls
smb_direct_post_send() we remove the last
element in send_ctx->msg_list and move all
others into last->sibling_list. As only
last has IB_SEND_SIGNALED and gets a completion
vis send_done().
3. send_done() has an easy way to free all others
in sendmsg->sibling_list (if there are any).
And use list_for_each_entry_safe() instead of
a complex custom logic.
This will help us to share send_done() in common
code soon, as it will work fine for the client too,
where last->sibling_list is currently always an empty list.
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
This will be used to implement a logic in order to make sure
we don't overflow the send submission queue for ib_post_send().
We will initialize the local credits with the
fixed sp->send_credit_target value, which matches
the reserved slots in the submission queue for ib_post_send().
We will be a local credit first and then wait for a remote credit,
if we managed to get both we are allowed to post an
IB_WR_SEND[_WITH_INV]. The local credit is given back to
the pool when we get the local ib_post_send() completion,
while remote credits are granted by the peer.
From reading the git history of the linux smbdirect
implementations in client and server) it was seen
that a peer granted more credits than we requested.
I guess that only happened because of bugs in our
implementation which was active as client and server.
I guess Windows won't do that.
So the local credits make sure we only use the amount
of credits we asked for.
The client already has some logic for this based on
smbdirect_socket.send_io.pending.count, but that
counts in the order direction and makes it complex it
share common logic for various credits classes.
That logic will be replaced soon.
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Make use of rdma_rw_mr_factor() to calculate the number of rw
credits and the number of pages per RDMA RW operation.
We get the same numbers for iWarp connections, tested
with siw.ko and irdma.ko (in iWarp mode).
siw:
CIFS: max_qp_rd_atom=128, max_fast_reg_page_list_len = 256
CIFS: max_sgl_rd=0, max_sge_rd=1
CIFS: responder_resources=32 max_frmr_depth=256 mr_io.type=0
CIFS: max_send_wr 384, device reporting max_cqe 3276800 max_qp_wr 32768
ksmbd: max_fast_reg_page_list_len = 256, max_sgl_rd=0, max_sge_rd=1
ksmbd: device reporting max_cqe 3276800 max_qp_wr 32768
ksmbd: Old sc->rw_io.credits: max = 9, num_pages = 256
ksmbd: New sc->rw_io.credits: max = 9, num_pages = 256, maxpages=2048
ksmbd: Info: rdma_send_wr 27 + max_send_wr 256 = 283
irdma (in iWarp mode):
CIFS: max_qp_rd_atom=127, max_fast_reg_page_list_len = 262144
CIFS: max_sgl_rd=0, max_sge_rd=13
CIFS: responder_resources=32 max_frmr_depth=2048 mr_io.type=0
CIFS: max_send_wr 384, device reporting max_cqe 1048574 max_qp_wr 4063
ksmbd: max_fast_reg_page_list_len = 262144, max_sgl_rd=0, max_sge_rd=13
ksmbd: device reporting max_cqe 1048574 max_qp_wr 4063
ksmbd: Old sc->rw_io.credits: max = 9, num_pages = 256
ksmbd: New sc->rw_io.credits: max = 9, num_pages = 256, maxpages=2048
ksmbd: rdma_send_wr 27 + max_send_wr 256 = 283
This means that we get the different correct numbers for ROCE,
tested with rdma_rxe.ko and irdma.ko (in RoCEv2 mode).
rxe:
CIFS: max_qp_rd_atom=128, max_fast_reg_page_list_len = 512
CIFS: max_sgl_rd=0, max_sge_rd=32
CIFS: responder_resources=32 max_frmr_depth=512 mr_io.type=0
CIFS: max_send_wr 384, device reporting max_cqe 32767 max_qp_wr 1048576
ksmbd: max_fast_reg_page_list_len = 512, max_sgl_rd=0, max_sge_rd=32
ksmbd: device reporting max_cqe 32767 max_qp_wr 1048576
ksmbd: Old sc->rw_io.credits: max = 9, num_pages = 256
ksmbd: New sc->rw_io.credits: max = 65, num_pages = 32, maxpages=2048
ksmbd: rdma_send_wr 65 + max_send_wr 256 = 321
irdma (in RoCEv2 mode):
CIFS: max_qp_rd_atom=127, max_fast_reg_page_list_len = 262144,
CIFS: max_sgl_rd=0, max_sge_rd=13
CIFS: responder_resources=32 max_frmr_depth=2048 mr_io.type=0
CIFS: max_send_wr 384, device reporting max_cqe 1048574 max_qp_wr 4063
ksmbd: max_fast_reg_page_list_len = 262144, max_sgl_rd=0, max_sge_rd=13
ksmbd: device reporting max_cqe 1048574 max_qp_wr 4063
ksmbd: Old sc->rw_io.credits: max = 9, num_pages = 256,
ksmbd: New sc->rw_io.credits: max = 159, num_pages = 13, maxpages=2048
ksmbd: rdma_send_wr 159 + max_send_wr 256 = 415
And rely on rdma_rw_init_qp() to setup ib_mr_pool_init() for
RW MRs. ib_mr_pool_destroy() will be called by rdma_rw_cleanup_mrs().
It seems the code was implemented before the rdma_rw_* layer
was fully established in the kernel.
While there also add additional space for ib_drain_qp().
This should make sure ib_post_send() will never fail
because the submission queue is full.
Fixes: ddbdc861e3 ("ksmbd: smbd: introduce read/write credits for RDMA read/write")
Fixes: 4c564f03e2 ("smb: server: make use of common smbdirect_socket")
Fixes: 177368b992 ("smb: server: make use of common smbdirect_socket_parameters")
Fixes: 95475d8886 ("smb: server: make use smbdirect_socket.rw_io.credits")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Pull SCSI fixes from James Bottomley:
"All driver fixes. The big change is the storvsc one to rejig the
hyper-v channel handling to be more efficient for SMP virtual
machines"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: phy: dt-bindings: Add QMP UFS PHY compatible for Kaanapali
scsi: ufs: qcom: dt-bindings: Document the Kaanapali UFS controller
scsi: libfc: Prevent integer overflow in fc_fcp_recv_data()
scsi: qla4xxx: Fix typos in comments
scsi: storvsc: Prefer returning channel with the same CPU as on the I/O issuing CPU
Pull hotfixes from Andrew Morton:
"17 hotfixes. 12 are cc:stable and 14 are for MM.
There's a two-patch DAMON series from SeongJae Park which addresses a
missed check and possible memory leak. Apart from that it's all
singletons - please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-22-12-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
csky: abiv2: adapt to new folio flags field
mm/damon/core: use damos_commit_quota_goal() for new goal commit
mm/damon/core: fix potential memory leak by cleaning ops_filter in damon_destroy_scheme
hugetlbfs: move lock assertions after early returns in huge_pmd_unshare()
vmw_balloon: indicate success when effectively deflating during migration
mm/damon/core: fix list_add_tail() call on damon_call()
mm/mremap: correctly account old mapping after MREMAP_DONTUNMAP remap
mm: prevent poison consumption when splitting THP
ocfs2: clear extent cache after moving/defragmenting extents
mm: don't spin in add_stack_record when gfp flags don't allow
dma-debug: don't report false positives with DMA_BOUNCE_UNALIGNED_KMALLOC
mm/damon/sysfs: dealloc commit test ctx always
mm/damon/sysfs: catch commit test ctx alloc failure
hung_task: fix warnings caused by unaligned lock pointers
Same as [1] but also with netdev@ as an additional mailing list.
io_uring zero copy receive is of particular interest to netdev
participants too, given its tight integration to netdev core.
With this updated entry, folks running get_maintainer.pl on patches that
touch io_uring/zcrx.* will know to send it to netdev@ as well.
Note that this doesn't mean all changes require explicit acks from
netdev; this is purely for wider visibility and for other contributors
to know where to send patches.
[1]: https://lore.kernel.org/io-uring/989528e611b51d71fb712691ebfb76d2059ba561.1755461246.git.asml.silence@gmail.com/
Signed-off-by: David Wei <dw@davidwei.uk>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
[axboe: use correct io_uring tree URL]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the indentation to ensure consistent code style and improve
readability and to fix the errors:
ERROR: code indent should use tabs where possible
+ return io_net_import_vec(req, kmsg, sr->buf, sr->len, ITER_SOURCE);$
ERROR: code indent should use tabs where possible
+^I^I^I struct io_big_cqe *big_cqe)$
Tested by running the /scripts/checkpatch.pl
Signed-off-by: Ranganath V N <vnranganath.20@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current approach is a bit naive, and hence calls the time querying
way too often. Only start the "doing work" timer when there's actual
work to do, and then use that information to terminate (and account) the
work time once done. This greatly reduces the frequency of these calls,
when they cannot have changed anyway.
Running a basic random reader that is setup to use SQPOLL, a profile
before this change shows these as the top cycle consumers:
+ 32.60% iou-sqp-1074 [kernel.kallsyms] [k] thread_group_cputime_adjusted
+ 19.97% iou-sqp-1074 [kernel.kallsyms] [k] thread_group_cputime
+ 12.20% io_uring io_uring [.] submitter_uring_fn
+ 4.13% iou-sqp-1074 [kernel.kallsyms] [k] getrusage
+ 2.45% iou-sqp-1074 [kernel.kallsyms] [k] io_submit_sqes
+ 2.18% iou-sqp-1074 [kernel.kallsyms] [k] __pi_memset_generic
+ 2.09% iou-sqp-1074 [kernel.kallsyms] [k] cputime_adjust
and after this change, top of profile looks as follows:
+ 36.23% io_uring io_uring [.] submitter_uring_fn
+ 23.26% iou-sqp-819 [kernel.kallsyms] [k] io_sq_thread
+ 10.14% iou-sqp-819 [kernel.kallsyms] [k] io_sq_tw
+ 6.52% iou-sqp-819 [kernel.kallsyms] [k] tctx_task_work_run
+ 4.82% iou-sqp-819 [kernel.kallsyms] [k] nvme_submit_cmds.part.0
+ 2.91% iou-sqp-819 [kernel.kallsyms] [k] io_submit_sqes
[...]
0.02% iou-sqp-819 [kernel.kallsyms] [k] cputime_adjust
where it's spending the cycles on things that actually matter.
Reported-by: Fengnan Chang <changfengnan@bytedance.com>
Cc: stable@vger.kernel.org
Fixes: 3fcb9d1720 ("io_uring/sqpoll: statistics of the true utilization of sq threads")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
getrusage() does a lot more than what the SQPOLL accounting needs, the
latter only cares about (and uses) the stime. Rather than do a full
RUSAGE_SELF summation, just query the used stime instead.
Cc: stable@vger.kernel.org
Fixes: 3fcb9d1720 ("io_uring/sqpoll: statistics of the true utilization of sq threads")
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
According to Maciej W. Rozycki <macro@orcam.me.uk>, the
mips_pcibios_init() for malta adjusts root bus IO resource start
address to prevent interfering with PIIX4 I/O cycle decoding. Adjusting
lower bound leaves PIIX4 IO resources outside of the root bus resource
and assign_fixed_resource_on_bus() does not link the resources into the
resource tree.
Prior to commit ae81aad5c2 ("MIPS: PCI: Use pci_enable_resources()") the
arch specific pcibios_enable_resources() did not check if the resources
were assigned which diverges from what PCI core checks, effectively hiding
the PIIX4 IO resources were not properly within the resource tree. After
starting to use pcibios_enable_resources() from PCI core, enabling PIIX4
fails:
ata_piix 0000:00:0a.1: BAR 0 [io 0x01f0-0x01f7]: not claimed; can't enable device
ata_piix 0000:00:0a.1: probe with driver ata_piix failed with error -22
MIPS PCI code already has support for enforcing lower bounds using
PCIBIOS_MIN_IO in pcibios_align_resource() without altering the IO window
start address itself. Make malta PCI code too to use PCIBIOS_MIN_IO.
Fixes: ae81aad5c2 ("MIPS: PCI: Use pci_enable_resources()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/linux-pci/9085ab12-1559-4462-9b18-f03dcb9a4088@roeck-us.net/
Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/linux-pci/alpine.DEB.2.21.2510132229120.39634@angie.orcam.me.uk/
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://patch.msgid.link/20251017110903.1973-1-ilpo.jarvinen@linux.intel.com
Covering the PCI southbridge legacy port I/O range with a northbridge
resource reservation prevents MIPS Malta platform code from claiming its
standard legacy resources. This is because request_resource() calls
cause a clash with the previous reservation and consequently fail.
Change to using insert_resource() so as to prevent the clash, switching
the legacy reservations from:
00000000-00ffffff : MSC PCI I/O
00000020-00000021 : pic1
00000070-00000077 : rtc0
000000a0-000000a1 : pic2
[...]
to:
00000000-00ffffff : MSC PCI I/O
00000000-0000001f : dma1
00000020-00000021 : pic1
00000040-0000005f : timer
00000060-0000006f : keyboard
00000070-00000077 : rtc0
00000080-0000008f : dma page reg
000000a0-000000a1 : pic2
000000c0-000000df : dma2
[...]
Fixes: ae81aad5c2 ("MIPS: PCI: Use pci_enable_resources()")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: stable@vger.kernel.org # v6.18+
Link: https://patch.msgid.link/alpine.DEB.2.21.2510212001250.8377@angie.orcam.me.uk
MIPS Malta platform code registers the PCI southbridge legacy port I/O
PS/2 keyboard range as a standard resource marked as busy. It prevents
the i8042 driver from registering as it fails to claim the resource in
a call to i8042_platform_init(). Consequently PS/2 keyboard and mouse
devices cannot be used with this platform.
Fix the issue by removing the busy marker from the standard reservation,
making the driver register successfully:
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
and the resource show up as expected among the legacy devices:
00000000-00ffffff : MSC PCI I/O
00000000-0000001f : dma1
00000020-00000021 : pic1
00000040-0000005f : timer
00000060-0000006f : keyboard
00000060-0000006f : i8042
00000070-00000077 : rtc0
00000080-0000008f : dma page reg
000000a0-000000a1 : pic2
000000c0-000000df : dma2
[...]
If the i8042 driver has not been configured, then the standard resource
will remain there preventing any conflicting dynamic assignment of this
PCI port I/O address range.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/alpine.DEB.2.21.2510211919240.8377@angie.orcam.me.uk
The block layer PI generation / verification code expects the bio_vecs
to have at least LBA size (or more correctly integrity internal)
granularity. With the direct I/O alignment relaxation in 2022, user
space can now feed bios with less alignment than that, leading to
scribbling outside the PI buffers. Apparently this wasn't noticed so far
because none of the tests generate such buffers, but since 851c4c96db
("xfs: implement XFS_IOC_DIOINFO in terms of vfs_getattr"), xfstests
generic/013 by default generates such I/O now that the relaxed alignment
is advertised by the XFS_IOC_DIOINFO ioctl.
Fix this by increasing the required alignment when using PI, although
handling arbitrary alignment in the long run would be even nicer.
Fixes: bf8d08532b ("iomap: add support for dma aligned direct-io")
Fixes: b1a000d3b8 ("block: relax direct io memory alignment")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull x86 platform driver fixes from Ilpo Järvinen:
- alienware-wmi-wmax:
- Fix NULL pointer dereference in sleep handlers
- Add AWCC support to Dell G15 5530
- mellanox: mlxbf-pmc: add sysfs_attr_init() to count_clock init
* tag 'platform-drivers-x86-v6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: alienware-wmi-wmax: Add AWCC support to Dell G15 5530
MAINTAINERS: add Denis Benato as maintainer for asus notebooks
platform/mellanox: mlxbf-pmc: add sysfs_attr_init() to count_clock init
platform/x86: alienware-wmi-wmax: Fix NULL pointer dereference in sleep handlers
Pull erofs fixes from Gao Xiang:
"Just three small fixes to address fuzzed images in relatively new
features, as reported by Robert.
- Hardening against fuzzed encoded extents
- Fix infinite loops due to crafted subpage compact indexes
- Improve z_erofs_extent_lookback()"
* tag 'erofs-for-6.18-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: consolidate z_erofs_extent_lookback()
erofs: avoid infinite loops due to corrupted subpage compact indexes
erofs: fix crafted invalid cases for encoded extents
Pull 9pfs fix from Dominique Martinet:
"Fix 9p cache=mmap regression by revert
This reverts the problematic commit instead of trying to fix it in a
rush"
* tag '9p-for-6.18-rc3-v2' of https://github.com/martinetd/linux:
Revert "fs/9p: Refresh metadata in d_revalidate for uncached mode too"
In some legacy platforms the MSI controller for a PCI host bridge is
identified by an msi-parent property whose phandle points at an MSI
controller node with no #msi-cells property, that implicitly
means #msi-cells == 0.
For such platforms, mapping a device ID and retrieving the MSI controller
node becomes simply a matter of checking whether in the device hierarchy
there is an msi-parent property pointing at an MSI controller node with
such characteristics.
Add a helper function to of_msi_xlate() to check the msi-parent property in
addition to msi-map and retrieve the MSI controller node (with a 1:1 ID
deviceID-IN<->deviceID-OUT mapping) to provide support for deviceID
mapping and MSI controller node retrieval for such platforms.
Fixes: 57d72196df ("irqchip/gic-v5: Add GICv5 ITS support")
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: Sascha Bischoff <sascha.bischoff@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20251021124103.198419-2-lpieralisi@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Fix compilation failure when compiling the kernel with the x32 toolchain.
In file included from check.c:16:
check.c: In function ¡check_abs_references¢:
/usr/src/git/linux-2.6/tools/objtool/include/objtool/warn.h:47:17: error: format ¡%lx¢ expects argument of type ¡long unsigned int¢, but argument 7 has type ¡u64¢ {aka ¡long
long unsigned int¢} [-Werror=format=]
47 | "%s%s%s: objtool" extra ": " format "\n", \
| ^~~~~~~~~~~~~~~~~
/usr/src/git/linux-2.6/tools/objtool/include/objtool/warn.h:54:9: note: in expansion of macro ¡___WARN¢
54 | ___WARN(severity, "", format, ##__VA_ARGS__)
| ^~~~~~~
/usr/src/git/linux-2.6/tools/objtool/include/objtool/warn.h:74:27: note: in expansion of macro ¡__WARN¢
74 | #define WARN(format, ...) __WARN(WARN_STR, format, ##__VA_ARGS__)
| ^~~~~~
check.c:4713:33: note: in expansion of macro ¡WARN¢
4713 | WARN("section %s has absolute relocation at offset 0x%lx",
| ^~~~
Fixes: 0d6e4563fc ("objtool: Add action to check for absence of absolute relocations")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://patch.msgid.link/1ac32fff-2e67-5155-f570-69aad5bf5412@redhat.com
Between Rust 1.79 and 1.86, under `CONFIG_RUST_KERNEL_DOCTESTS=y`,
`objtool` may report:
rust/doctests_kernel_generated.o: warning: objtool:
rust_doctest_kernel_alloc_kbox_rs_13() falls through to next
function rust_doctest_kernel_alloc_kvec_rs_0()
(as well as in rust_doctest_kernel_alloc_kvec_rs_0) due to calls to the
`noreturn` symbol:
core::option::expect_failed
from code added in commits 779db37373 ("rust: alloc: kvec: implement
AsPageIter for VVec") and 671618432f ("rust: alloc: kbox: implement
AsPageIter for VBox").
Thus add the mangled one to the list so that `objtool` knows it is
actually `noreturn`.
This can be reproduced as well in other versions by tweaking the code,
such as the latest stable Rust (1.90.0).
Stable does not have code that triggers this, but it could have it in
the future. Downstream forks could too. Thus tag it for backport.
See commit 56d680dd23 ("objtool/rust: list `noreturn` Rust functions")
for more details.
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Cc: stable@vger.kernel.org # Needed in 6.12.y and later.
Link: https://patch.msgid.link/20251020020714.2511718-1-ojeda@kernel.org
Matteo reported hitting the assert_list_leaf_cfs_rq() warning from
enqueue_task_fair() post commit fe8d238e64 ("sched/fair: Propagate
load for throttled cfs_rq") which transitioned to using
cfs_rq_pelt_clock_throttled() check for leaf cfs_rq insertions in
propagate_entity_cfs_rq().
The "cfs_rq->pelt_clock_throttled" flag is used to indicate if the
hierarchy has its PELT frozen. If a cfs_rq's PELT is marked frozen, all
its descendants should have their PELT frozen too or weird things can
happen as a result of children accumulating PELT signals when the
parents have their PELT clock stopped.
Another side effect of this is the loss of integrity of the leaf cfs_rq
list. As debugged by Aaron, consider the following hierarchy:
root(#)
/ \
A(#) B(*)
|
C <--- new cgroup
|
D <--- new cgroup
# - Already on leaf cfs_rq list
* - Throttled with PELT frozen
The newly created cgroups don't have their "pelt_clock_throttled" signal
synced with cgroup B. Next, the following series of events occur:
1. online_fair_sched_group() for cgroup D will call
propagate_entity_cfs_rq(). (Same can happen if a throttled task is
moved to cgroup C and enqueue_task_fair() returns early.)
propagate_entity_cfs_rq() adds the cfs_rq of cgroup C to
"rq->tmp_alone_branch" since its PELT clock is not marked throttled
and cfs_rq of cgroup B is not on the list.
cfs_rq of cgroup B is skipped since its PELT is throttled.
root cfs_rq already exists on cfs_rq leading to
list_add_leaf_cfs_rq() returning early.
The cfs_rq of cgroup C is left dangling on the
"rq->tmp_alone_branch".
2. A new task wakes up on cgroup A. Since the whole hierarchy is already
on the leaf cfs_rq list, list_add_leaf_cfs_rq() keeps returning early
without any modifications to "rq->tmp_alone_branch".
The final assert_list_leaf_cfs_rq() in enqueue_task_fair() sees the
dangling reference to cgroup C's cfs_rq in "rq->tmp_alone_branch".
!!! Splat !!!
Syncing the "pelt_clock_throttled" indicator with parent cfs_rq is not
enough since the new cfs_rq is not yet enqueued on the hierarchy. A
dequeue on other subtree on the throttled hierarchy can freeze the PELT
clock for the parent hierarchy without setting the indicators for this
newly added cfs_rq which was never enqueued.
Since there are no tasks on the new hierarchy, start a cfs_rq on a
throttled hierarchy with its PELT clock throttled. The first enqueue, or
the distribution (whichever happens first) will unfreeze the PELT clock
and queue the cfs_rq on the leaf cfs_rq list.
While at it, add an assert_list_leaf_cfs_rq() in
propagate_entity_cfs_rq() to catch such cases in the future.
Closes: https://lore.kernel.org/lkml/58a587d694f33c2ea487c700b0d046fa@codethink.co.uk/
Fixes: e1fad12dcb ("sched/fair: Switch to task based throttle model")
Reported-by: Matteo Martelli <matteo.martelli@codethink.co.uk>
Suggested-by: Aaron Lu <ziqianlu@bytedance.com>
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Aaron Lu <ziqianlu@bytedance.com>
Tested-by: Aaron Lu <ziqianlu@bytedance.com>
Tested-by: Matteo Martelli <matteo.martelli@codethink.co.uk>
Link: https://patch.msgid.link/20251021053522.37583-1-kprateek.nayak@amd.com
Some MediaTek SoCs got a gated UART baud clock, which currently gets
disabled as the clk subsystem believes it would be unused. This results in
the uart freezing right after "clk: Disabling unused clocks" on those
platforms.
Request the baud clock to be prepared and enabled during probe, and to
restore run-time power management capabilities to what it was before commit
e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock
management") disable and unprepare the baud clock when suspending the UART,
prepare and enable it again when resuming it.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Fixes: b6c7ff2693 ("serial: 8250_mtk: Simplify clock sequencing and runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/de5197ccc31e1dab0965cabcc11ca92e67246cf6.1758058441.git.daniel@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of reset_control_deassert() in the probe
function to prevent continuing probe when reset deassertion fails.
Previously, reset_control_deassert() was called without checking its
return value, which could lead to probe continuing even when the
device reset wasn't properly deasserted.
The fix checks the return value and returns an error with dev_err_probe()
if reset deassertion fails, providing better error handling and
diagnostics.
Fixes: acbdad8dd1 ("serial: 8250_dw: simplify optional reset handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251019095131.252848-1-a.shimko.dev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 43c51bb573 ("sc16is7xx: make sure device is in suspend once
probed") permanently enabled access to the enhanced features in
sc16is7xx_probe(), and it is never disabled after that.
Therefore, remove re-enable of enhanced features in
sc16is7xx_set_baud(). This eliminates a potential useless read + write
cycle each time the baud rate is reconfigured.
Fixes: 43c51bb573 ("sc16is7xx: make sure device is in suspend once probed")
Cc: stable <stable@kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20251006142002.177475-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]---
Cc: stable <stable@kernel.org>
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Link: https://patch.msgid.link/20250923154707.1089900-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a filesystem with parent pointers, xchk_nlinks_collect_dir walks both
the directory entries (data fork) and the parent pointers (attr fork) to
determine the correct link count. Unfortunately I forgot to update the
lock mode logic to handle the case of a directory whose attr fork is in
btree format and has not yet been loaded *and* whose data fork doesn't
need loading.
This leads to a bunch of assertions from xfs/286 in xfs_iread_extents
because we only took ILOCK_SHARED, not ILOCK_EXCL. You'd need the rare
happenstance of a directory with a large number of non-pptr extended
attributes set and enough memory pressure to cause the directory to be
evicted and partially reloaded from disk.
I /think/ this only started in 6.18-rc1 because I've started seeing OOM
errors with the maple tree slab using 70% of memory, and this didn't
happen in 6.17. Yay dynamic systems!
Cc: stable@vger.kernel.org # v6.10
Fixes: 77ede5f44b ("xfs: walk directory parent pointers to determine backref count")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Apparently we can never deprecate mount options in this project, because
it will invariably turn out that some foolish userspace depends on some
behavior and break. From Oleksandr Natalenko:
In v6.18, the attr2 XFS mount option is removed. This may silently
break system boot if the attr2 option is still present in /etc/fstab
for rootfs.
Consider Arch Linux that is being set up from scratch with / being
formatted as XFS. The genfstab command that is used to generate
/etc/fstab produces something like this by default:
/dev/sda2 on / type xfs (rw,relatime,attr2,discard,inode64,logbufs=8,logbsize=32k,noquota)
Once the system is set up and rebooted, there's no deprecation warning
seen in the kernel log:
# cat /proc/cmdline
root=UUID=77b42de2-397e-47ee-a1ef-4dfd430e47e9 rootflags=discard rd.luks.options=discard quiet
# dmesg | grep -i xfs
[ 2.409818] SGI XFS with ACLs, security attributes, realtime, scrub, repair, quota, no debug enabled
[ 2.415341] XFS (sda2): Mounting V5 Filesystem 77b42de2-397e-47ee-a1ef-4dfd430e47e9
[ 2.442546] XFS (sda2): Ending clean mount
Although as per the deprecation intention, it should be there.
Vlastimil (in Cc) suggests this is because xfs_fs_warn_deprecated()
doesn't produce any warning by design if the XFS FS is set to be
rootfs and gets remounted read-write during boot. This imposes two
problems:
1) a user doesn't see the deprecation warning; and
2) with v6.18 kernel, the read-write remount fails because of unknown
attr2 option rendering system unusable:
systemd[1]: Switching root.
systemd-remount-fs[225]: /usr/bin/mount for / exited with exit status 32.
# mount -o rw /
mount: /: fsconfig() failed: xfs: Unknown parameter 'attr2'.
Thorsten (in Cc) suggested reporting this as a user-visible regression.
From my PoV, although the deprecation is in place for 5 years already,
it may not be visible enough as the warning is not emitted for rootfs.
Considering the amount of systems set up with XFS on /, this may
impose a mass problem for users.
Vlastimil suggested making attr2 option a complete noop instead of
removing it.
IOWs, the initrd mounts the root fs with (I assume) no mount options,
and mount -a remounts with whatever options are in fstab. However,
XFS doesn't complain about deprecated mount options during a remount, so
technically speaking we were not warning all users in all combinations
that they were heading for a cliff.
Gotcha!!
Now, how did 'attr2' get slurped up on so many systems? The old code
would put that in /proc/mounts if the filesystem happened to be in attr2
mode, even if user hadn't mounted with any such option. IOWs, this is
because someone thought it would be a good idea to advertise system
state via /proc/mounts.
The easy way to fix this is to reintroduce the four mount options but
map them to a no-op option that ignores them, and hope that nobody's
depending on attr2 to appear in /proc/mounts. (Hint: use the fsgeometry
ioctl). But we've learned our lesson, so complain as LOUDLY as possible
about the deprecation.
Lessons learned:
1. Don't expose system state via /proc/mounts; the only strings that
ought to be there are options *explicitly* provided by the user.
2. Never tidy, it's not worth the stress and irritation.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: stable@vger.kernel.org # v6.18-rc1
Fixes: b9a176e541 ("xfs: remove deprecated mount options")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
The deprecation of the 'attr2' mount option in 6.18 wasn't entirely
successful because nobody noticed that the kernel never printed a
warning about attr2 being set in fstab if the only xfs filesystem is the
root fs; the initramfs mounts the root fs with no mount options; and the
init scripts only conveyed the fstab options by remounting the root fs.
Fix this by making it complain all the time.
Cc: stable@vger.kernel.org # v5.13
Fixes: 92cf7d3638 ("xfs: Skip repetitive warnings about mount options")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
xfs_daddr_t is a signed type, which means that xfs_buf_map_verify is
using a signed comparison. This causes problems if bt_nr_sectors is
never overridden (e.g. in the case of an xfbtree for rmap btree repairs)
because even daddr 0 can't pass the verifier test in that case.
Define an explicit max constant and set the initial bt_nr_sectors to a
positive value.
Found by xfs/422.
Cc: stable@vger.kernel.org # v6.18-rc1
Fixes: 42852fe57c ("xfs: track the number of blocks in each buftarg")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
When there is no port entry in the tcpci entry itself, the driver will
trigger an error message "OF: graph: no port node found in /...../typec" .
It is documented that the dts node should contain an connector entry
with ports and several port pointing to devices with usb-role-switch
property set. Only when those connector entry is missing, it should
check for port entries in the main node.
We switch the search order for looking after ports, which will avoid the
failure message while there are explicit connector entries.
Fixes: d56de8c9a1 ("usb: typec: tcpm: try to get role switch from tcpc fwnode")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://patch.msgid.link/20251013-b4-ml-topic-tcpm-v2-1-63c9b2ab8a0b@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the check on the maximum transfer length in Raw Gadget for both
control and non-control transfers.
Limiting the transfer length causes a problem with emulating USB devices
whose full configuration descriptor exceeds PAGE_SIZE in length.
Overall, there does not appear to be any reason to enforce any kind of
transfer length limit on the Raw Gadget side for either control or
non-control transfers, so let's just drop the related check.
Cc: stable <stable@kernel.org>
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://patch.msgid.link/a6024e8eab679043e9b8a5defdb41c4bda62f02b.1761085528.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the print before releasing the delayed node.
In my initial testing there was a bug that was causing delayed_nodes
to not get freed which is why I put the print after the release. This
obviously neglects the case where the delayed node is properly freed.
Add condition to make sure we only print if we have more than one
reference to the delayed_node to prevent printing when we only have
the reference taken in btrfs_kill_all_delayed_nodes().
Fixes: b767a28d61 ("btrfs: print leaked references in kill_all_delayed_nodes()")
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Leo Martins <loemra.dev@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are GPIO controllers such as the one present in the LX2160ARDB
QIXIS FPGA which have fixed-direction input and output GPIO lines mixed
together in a single register. This cannot be modeled using the
gpio-regmap as-is since there is no way to present the true direction of
a GPIO line.
In order to make this use case possible, add a new configuration
parameter - fixed_direction_output - into the gpio_regmap_config
structure. This will enable user drivers to provide a bitmap that
represents the fixed direction of the GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Fix incorrect use of PTR_ERR_OR_ZERO() in topology_parse_cpu_capacity()
which causes the code to proceed with NULL clock pointers. The current
logic uses !PTR_ERR_OR_ZERO(cpu_clk) which evaluates to true for both
valid pointers and NULL, leading to potential NULL pointer dereference
in clk_get_rate().
Per include/linux/err.h documentation, PTR_ERR_OR_ZERO(ptr) returns:
"The error code within @ptr if it is an error pointer; 0 otherwise."
This means PTR_ERR_OR_ZERO() returns 0 for both valid pointers AND NULL
pointers. Therefore !PTR_ERR_OR_ZERO(cpu_clk) evaluates to true (proceed)
when cpu_clk is either valid or NULL, causing clk_get_rate(NULL) to be
called when of_clk_get() returns NULL.
Replace with !IS_ERR_OR_NULL(cpu_clk) which only proceeds for valid
pointers, preventing potential NULL pointer dereference in clk_get_rate().
Cc: stable <stable@kernel.org>
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: b8fe128dad ("arch_topology: Adjust initial CPU capacities with current freq")
Link: https://patch.msgid.link/20250923174308.1771906-1-kaushlendra.kumar@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early error path in hdm_probe() can jump to err_free_mdev before
&mdev->dev has been initialized with device_initialize(). Calling
put_device(&mdev->dev) there triggers a device core WARN and ends up
invoking kref_put(&kobj->kref, kobject_release) on an uninitialized
kobject.
In this path the private struct was only kmalloc'ed and the intended
release is effectively kfree(mdev) anyway, so free it directly instead
of calling put_device() on an uninitialized device.
This removes the WARNING and fixes the pre-initialization error path.
Fixes: 97a6f772f3 ("drivers: most: add USB adapter driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Victoria Votokina <Victoria.Votokina@kaspersky.com>
Link: https://patch.msgid.link/20251010105241.4087114-3-Victoria.Votokina@kaspersky.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdm_disconnect() calls most_deregister_interface(), which eventually
unregisters the MOST interface device with device_unregister(iface->dev).
If that drops the last reference, the device core may call release_mdev()
immediately while hdm_disconnect() is still executing.
The old code also freed several mdev-owned allocations in
hdm_disconnect() and then performed additional put_device() calls.
Depending on refcount order, this could lead to use-after-free or
double-free when release_mdev() ran (or when unregister paths also
performed puts).
Fix by moving the frees of mdev-owned allocations into release_mdev(),
so they happen exactly once when the device is truly released, and by
dropping the extra put_device() calls in hdm_disconnect() that are
redundant after device_unregister() and most_deregister_interface().
This addresses the KASAN slab-use-after-free reported by syzbot in
hdm_disconnect(). See report and stack traces in the bug link below.
Reported-by: syzbot+916742d5d24f6c254761@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=916742d5d24f6c254761
Fixes: 97a6f772f3 ("drivers: most: add USB adapter driver")
Signed-off-by: Victoria Votokina <Victoria.Votokina@kaspersky.com>
Link: https://patch.msgid.link/20251010105241.4087114-2-Victoria.Votokina@kaspersky.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no scenarios where a weak increment is invalid on binder_node.
The only possible case where it could be invalid is if the kernel
delivers BR_DECREFS to the process that owns the node, and then
increments the weak refcount again, effectively "reviving" a dead node.
However, that is not possible: when the BR_DECREFS command is delivered,
the kernel removes and frees the binder_node. The fact that you were
able to call binder_inc_node_nilocked() implies that the node is not yet
destroyed, which implies that BR_DECREFS has not been delivered to
userspace, so incrementing the weak refcount is valid.
Note that it's currently possible to trigger this condition if the owner
calls BINDER_THREAD_EXIT while node->has_weak_ref is true. This causes
BC_INCREFS on binder_ref instances to fail when they should not.
Cc: stable@vger.kernel.org
Fixes: 457b9a6f09 ("Staging: android: add binder driver")
Reported-by: Yu-Ting Tseng <yutingtseng@google.com>
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251015-binder-weak-inc-v1-1-7914b092c371@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building with -Wincompatible-function-pointer-types-strict, a
warning designed to catch kernel control flow integrity (kCFI) issues at
build time, there is an instance in the new mei late binding code
originating from the type parameter of mei_lb_push_payload():
drivers/misc/mei/mei_lb.c:211:18: error: incompatible function pointer types initializing 'int (*)(struct device *, u32, u32, const void *, size_t)' (aka 'int (*)(struct device *, unsigned int, unsigned int, const void *, unsigned long)') with an expression of type 'int (struct device *, enum intel_lb_type, u32, const void *, size_t)' (aka 'int (struct device *, enum intel_lb_type, unsigned int, const void *, unsigned long)') [-Werror,-Wincompatible-function-pointer-types-strict]
211 | .push_payload = mei_lb_push_payload,
| ^~~~~~~~~~~~~~~~~~~
While 'unsigned int' and 'enum intel_lb_type' are ABI compatible, hence
no regular warning from -Wincompatible-function-pointer-types, the
mismatch will trigger a kCFI violation when mei_lb_push_payload() is
called indirectly.
Update the type parameter of mei_lb_push_payload() to be 'u32' to match
the prototype in 'struct intel_lb_component_ops', clearing up the
warning and kCFI violation.
Fixes: 741eeabb7c ("mei: late_bind: add late binding component driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20250920-drm-xe-fix-wifpts-v1-1-c89b5357c7ba@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 290434474c.
That commit broke cache=mmap, a mode that doesn't cache metadata,
but still has writeback cache.
In commit 290434474c ("fs/9p: Refresh metadata in d_revalidate
for uncached mode too") we considered metadata cache to be enough to
not look at the server, but in writeback cache too looking at the server
size would make the vfs consider the file has been truncated before the
data has been flushed out, making the following repro fail (nothing is
ever read back, the resulting file ends up with no data written)
```
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
char buf[4096];
int main(int argc, char *argv[])
{
int ret, i;
int fdw, fdr;
if (argc < 2)
return 1;
fdw = openat(AT_FDCWD, argv[1], O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0600);
if (fdw < 0) {
fprintf(stderr, "cannot open fdw\n");
return 1;
}
write(fdw, buf, sizeof(buf));
fdr = openat(AT_FDCWD, argv[1], O_RDONLY|O_CLOEXEC);
if (fdr < 0) {
fprintf(stderr, "cannot open fdr\n");
close(fdw);
return 1;
}
for (i = 0; i < 10; i++) {
ret = read(fdr, buf, sizeof(buf));
fprintf(stderr, "i: %d, read returns %d\n", i, ret);
}
close(fdr);
close(fdw);
return 0;
}
```
There is a fix for this particular reproducer but it looks like there
are other problems around metadata refresh (e.g. around file rename), so
revert this to avoid d_revalidate in uncached mode for now.
Reported-by: Song Liu <song@kernel.org>
Link: https://lkml.kernel.org/r/CAHzjS_u_SYdt5=2gYO_dxzMKXzGMt-TfdE_ueowg-Hq5tRCAiw@mail.gmail.com
Reported-by: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Link: https://lore.kernel.org/bpf/CAEf4BzZbCE4tLoDZyUf_aASpgAGFj75QMfSXX4a4dLYixnOiLg@mail.gmail.com/
Fixes: 290434474c ("fs/9p: Refresh metadata in d_revalidate for uncached mode too")
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Replace `dev_kfree_skb()` with `dev_kfree_skb_any()` in `start_xmit()`
which can be called from netpoll (hard IRQ) and from other contexts.
Also, `np->link_status` can be changed at any time by interrupt handler.
<idle>-0 [011] dNh4. 4541.754603: start_xmit <-netpoll_start_xmit
<idle>-0 [011] dNh4. 4541.754622: <stack trace>
=> [FTRACE TRAMPOLINE]
=> start_xmit
=> netpoll_start_xmit
=> netpoll_send_skb
=> write_msg
=> console_flush_all
=> console_unlock
=> vprintk_emit
=> _printk
=> rio_interrupt
=> __handle_irq_event_percpu
=> handle_irq_event
=> handle_fasteoi_irq
=> __common_interrupt
=> common_interrupt
=> asm_common_interrupt
=> mwait_idle
=> default_idle_call
=> do_idle
=> cpu_startup_entry
=> start_secondary
=> common_startup_64
This issue can occur when the link state changes from off to on
(e.g., plugging or unplugging the LAN cable) while transmitting a
packet. If the skb has a destructor, a warning message may be
printed in this situation.
-> consume_skb (dev_kfree_skb())
-> __kfree_skb()
-> skb_release_all()
-> skb_release_head_state(skb)
if (skb->destructor) {
DEBUG_NET_WARN_ON_ONCE(in_hardirq());
skb->destructor(skb);
}
Found by inspection.
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-on: D-Link DGE-550T Rev-A3
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251019075540.55697-1-yyyynoom@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2025-10-20
All patches are by me. The first 3 update the bxcan, esd and rockchip
driver to drop skbs in xmit of the device is in listen only mode.
The last patch targets the CAN netlink implementation to allow the
disabling of automatic restart after Bus-Off, even if the a driver
doesn't implement that callback.
* tag 'linux-can-fixes-for-6.18-20251020' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: netlink: can_changelink(): allow disabling of automatic restart
can: rockchip-canfd: rkcanfd_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
can: esd: acc_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
can: bxcan: bxcan_start_xmit(): use can_dev_dropped_skb() instead of can_dropped_invalid_skb()
====================
Link: https://patch.msgid.link/20251020152516.1590553-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot found that the local_unlock_nested_bh() call was
missing in some cases.
WARNING: possible recursive locking detected
syzkaller #0 Not tainted
--------------------------------------------
syz.2.329/7421 is trying to acquire lock:
ffffe8ffffd48888 ((&cell->bh_lock)){+...}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:44 [inline]
ffffe8ffffd48888 ((&cell->bh_lock)){+...}-{3:3}, at: gro_cells_receive+0x404/0x790 net/core/gro_cells.c:30
but task is already holding lock:
ffffe8ffffd48888 ((&cell->bh_lock)){+...}-{3:3}, at: spin_lock include/linux/spinlock_rt.h:44 [inline]
ffffe8ffffd48888 ((&cell->bh_lock)){+...}-{3:3}, at: gro_cells_receive+0x404/0x790 net/core/gro_cells.c:30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((&cell->bh_lock));
lock((&cell->bh_lock));
*** DEADLOCK ***
Given the introduction of @have_bh_lock variable, it seems the author
intent was to have the local_unlock_nested_bh() after the @unlock label.
Fixes: 25718fdcbd ("net: gro_cells: Use nested-BH locking for gro_cell")
Reported-by: syzbot+f9651b9a8212e1c8906f@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/68f65eb9.a70a0220.205af.0034.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20251020161114.1891141-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: handle late ADD_ADDR + selftests skip
Here are a few independent fixes related to MPTCP and its selftests:
- Patch 1: correctly handle ADD_ADDR being received after the switch to
'fully-established'. A fix for another recent fix backported up to
v5.14.
- Patches 2-5: properly mark some MPTCP Join subtests as 'skipped' if
the tested kernel doesn't support the feature being validated. Some
fixes for up to v5.13, v5.18, v6.11 and v6.18-rc1 respectively.
====================
Link: https://patch.msgid.link/20251020-net-mptcp-c-flag-late-add-addr-v1-0-8207030cb0e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The special C-flag case expects the ADD_ADDR to be received when
switching to 'fully-established'. But for various reasons, the ADD_ADDR
could be sent after the "4th ACK", and the special case doesn't work.
On NIPA, the new test validating this special case for the C-flag failed
a few times, e.g.
102 default limits, server deny join id 0
syn rx [FAIL] got 0 JOIN[s] syn rx expected 2
Server ns stats
(...)
MPTcpExtAddAddrTx 1
MPTcpExtEchoAdd 1
Client ns stats
(...)
MPTcpExtAddAddr 1
MPTcpExtEchoAddTx 1
synack rx [FAIL] got 0 JOIN[s] synack rx expected 2
ack rx [FAIL] got 0 JOIN[s] ack rx expected 2
join Rx [FAIL] see above
syn tx [FAIL] got 0 JOIN[s] syn tx expected 2
join Tx [FAIL] see above
I had a suspicion about what the issue could be: the ADD_ADDR might have
been received after the switch to the 'fully-established' state. The
issue was not easy to reproduce. The packet capture shown that the
ADD_ADDR can indeed be sent with a delay, and the client would not try
to establish subflows to it as expected.
A simple fix is not to mark the endpoints as 'used' in the C-flag case,
when looking at creating subflows to the remote initial IP address and
port. In this case, there is no need to try.
Note: newly added fullmesh endpoints will still continue to be used as
expected, thanks to the conditions behind mptcp_pm_add_addr_c_flag_case.
Fixes: 4b1ff850e0 ("mptcp: pm: in-kernel: usable client side with C-flag")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251020-net-mptcp-c-flag-late-add-addr-v1-1-8207030cb0e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initial m.delta[0] also needs to be checked against zero.
In addition, also drop the redundant logic that errors out for
lcn == 0 / m.delta[0] == 1 case.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Robert reported an infinite loop observed by two crafted images.
The root cause is that `clusterofs` can be larger than `lclustersize`
for !NONHEAD `lclusters` in corrupted subpage compact indexes, e.g.:
blocksize = lclustersize = 512 lcn = 6 clusterofs = 515
Move the corresponding check for full compress indexes to
`z_erofs_load_lcluster_from_disk()` to also cover subpage compact
compress indexes.
It also fixes the position of `m->type >= Z_EROFS_LCLUSTER_TYPE_MAX`
check, since it should be placed right after
`z_erofs_load_{compact,full}_lcluster()`.
Fixes: 8d2517aaee ("erofs: fix up compacted indexes for block size < 4096")
Fixes: 1a5223c182 ("erofs: do sanity check on m->type in z_erofs_load_compact_lcluster()")
Reported-by: Robert Morris <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/r/35167.1760645886@localhost
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
When damos_commit_quota_goals() is called for adding new DAMOS quota goals
of DAMOS_QUOTA_USER_INPUT metric, current_value fields of the new goals
should be also set as requested.
However, damos_commit_quota_goals() is not updating the field for the
case, since it is setting only metrics and target values using
damos_new_quota_goal(), and metric-optional union fields using
damos_commit_quota_goal_union(). As a result, users could see the first
current_value parameter that committed online with a new quota goal is
ignored. Users are assumed to commit the current_value for
DAMOS_QUOTA_USER_INPUT quota goals, since it is being used as a feedback.
Hence the real impact would be subtle. That said, this is obviously not
intended behavior.
Fix the issue by using damos_commit_quota_goal() which sets all quota goal
parameters, instead of damos_commit_quota_goal_union(), which sets only
the union fields.
Link: https://lkml.kernel.org/r/20251014001846.279282-1-sj@kernel.org
Fixes: 1aef9df0ee ("mm/damon/core: commit damos_quota_goal->nid")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [6.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When hugetlb_vmdelete_list() processes VMAs during truncate operations, it
may encounter VMAs where huge_pmd_unshare() is called without the required
shareable lock. This triggers an assertion failure in
hugetlb_vma_assert_locked().
The previous fix in commit dd83609b88 ("hugetlbfs: skip VMAs without
shareable locks in hugetlb_vmdelete_list") skipped entire VMAs without
shareable locks to avoid the assertion. However, this prevented pages
from being unmapped and freed, causing a regression in
fallocate(PUNCH_HOLE) operations where pages were not freed immediately,
as reported by Mark Brown.
Instead of checking locks in the caller or skipping VMAs, move the lock
assertions in huge_pmd_unshare() to after the early return checks. The
assertions are only needed when actual PMD unsharing work will be
performed. If the function returns early because sz != PMD_SIZE or the
PMD is not shared, no locks are required and assertions should not fire.
This approach reverts the VMA skipping logic from commit dd83609b88
("hugetlbfs: skip VMAs without shareable locks in hugetlb_vmdelete_list")
while moving the assertions to avoid the assertion failure, keeping all
the logic within huge_pmd_unshare() itself and allowing page unmapping and
freeing to proceed for all VMAs.
Link: https://lkml.kernel.org/r/20251014113344.21194-1-kartikey406@gmail.com
Fixes: dd83609b88 ("hugetlbfs: skip VMAs without shareable locks in hugetlb_vmdelete_list")
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Reported-by: <syzbot+f26d7c75c26ec19790e7@syzkaller.appspotmail.com>
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://syzkaller.appspot.com/bug?extid=f26d7c75c26ec19790e7
Suggested-by: David Hildenbrand <david@redhat.com>
Suggested-by: Oscar Salvador <osalvador@suse.de>
Tested-by: <syzbot+f26d7c75c26ec19790e7@syzkaller.appspotmail.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When migrating a balloon page, we first deflate the old page to then
inflate the new page.
However, if inflating the new page succeeded, we effectively deflated the
old page, reducing the balloon size.
In that case, the migration actually worked: similar to migrating+
immediately deflating the new page. The old page will be freed back to
the buddy.
Right now, the core will leave the page be marked as isolated (as we
returned an error). When later trying to putback that page, we will run
into the WARN_ON_ONCE() in balloon_page_putback().
That handling was changed in commit 3544c4facc ("mm/balloon_compaction:
stop using __ClearPageMovable()"); before that change, we would have
tolerated that way of handling it.
To fix it, let's just return 0 in that case, making the core effectively
just clear the "isolated" flag + freeing it back to the buddy as if the
migration succeeded. Note that the new page will also get freed when the
core puts the last reference.
Note that this also makes it all be more consistent: we will no longer
unisolate the page in the balloon driver while keeping it marked as being
isolated in migration core.
This was found by code inspection.
Link: https://lkml.kernel.org/r/20251014124455.478345-1-david@redhat.com
Fixes: 3544c4facc ("mm/balloon_compaction: stop using __ClearPageMovable()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Jerrin Shaji George <jerrin.shaji-george@broadcom.com>
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Each damon_ctx maintains callback requests using a linked list
(damon_ctx->call_controls). When a new callback request is received via
damon_call(), the new request should be added to the list. However, the
function is making a mistake at list_add_tail() invocation: putting the
new item to add and the list head to add it before, in the opposite order.
Because of the linked list manipulation implementation, the new request
can still be reached from the context's list head. But the list items
that were added before the new request are dropped from the list.
As a result, the callbacks are unexpectedly not invocated. Worse yet, if
the dropped callback requests were dynamically allocated, the memory is
leaked. Actually DAMON sysfs interface is using a dynamically allocated
repeat-mode callback request for automatic essential stats update. And
because the online DAMON parameters commit is using a non-repeat-mode
callback request, the issue can easily be reproduced, like below.
# damo start --damos_action stat --refresh_stat 1s
# damo tune --damos_action stat --refresh_stat 1s
The first command dynamically allocates the repeat-mode callback request
for automatic essential stat update. Users can see the essential stats
are automatically updated for every second, using the sysfs interface.
The second command calls damon_commit() with a new callback request that
was made for the commit. As a result, the previously added repeat-mode
callback request is dropped from the list. The automatic stats refresh
stops working, and the memory for the repeat-mode callback request is
leaked. It can be confirmed using kmemleak.
Fix the mistake on the list_add_tail() call.
Link: https://lkml.kernel.org/r/20251014205939.1206-1-sj@kernel.org
Fixes: 004ded6bee ("mm/damon: accept parallel damon_call() requests")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [6.17+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit b714ccb02a ("mm/mremap: complete refactor of move_vma()")
mistakenly introduced a new behaviour - clearing the VM_ACCOUNT flag of
the old mapping when a mapping is mremap()'d with the MREMAP_DONTUNMAP
flag set.
While we always clear the VM_LOCKED and VM_LOCKONFAULT flags for the old
mapping (the page tables have been moved, so there is no data that could
possibly be locked in memory), there is no reason to touch any other VMA
flags.
This is because after the move the old mapping is in a state as if it were
freshly mapped. This implies that the attributes of the mapping ought to
remain the same, including whether or not the mapping is accounted.
Link: https://lkml.kernel.org/r/20251013165836.273113-1-lorenzo.stoakes@oracle.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Fixes: b714ccb02a ("mm/mremap: complete refactor of move_vma()")
Reviewed-by: Pedro Falcato <pfalcato@suse.de>
Cc: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull VFIO fixlet from Alex Williamson:
"A tiny update as I'm changing jobs. Different email, same signing key
for now.
- Update VFIO maintainers entry (Alex Williamson)"
* tag 'vfio-v6.18-rc3' of https://github.com/awilliam/linux-vfio:
MAINTAINERS: Update Alex Williamson's email address
Current pte_mkwrite_novma() makes PTE dirty unconditionally. This may
mark some pages that are never written dirty wrongly. For example,
do_swap_page() may map the exclusive pages with writable and clean PTEs
if the VMA is writable and the page fault is for read access.
However, current pte_mkwrite_novma() implementation always dirties the
PTE. This may cause unnecessary disk writing if the pages are
never written before being reclaimed.
So, change pte_mkwrite_novma() to clear the PTE_RDONLY bit only if the
PTE_DIRTY bit is set to make it possible to make the PTE writable and
clean.
The current behavior was introduced in commit 73e86cb03c ("arm64:
Move PTE_RDONLY bit handling out of set_pte_at()"). Before that,
pte_mkwrite() only sets the PTE_WRITE bit, while set_pte_at() only
clears the PTE_RDONLY bit if both the PTE_WRITE and the PTE_DIRTY bits
are set.
To test the performance impact of the patch, on an arm64 server
machine, run 16 redis-server processes on socket 1 and 16
memtier_benchmark processes on socket 0 with mostly get
transactions (that is, redis-server will mostly read memory only).
The memory footprint of redis-server is larger than the available
memory, so swap out/in will be triggered. Test results show that the
patch can avoid most swapping out because the pages are mostly clean.
And the benchmark throughput improves ~23.9% in the test.
Fixes: 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Signed-off-by: Huang Ying <ying.huang@linux.alibaba.com>
Cc: Will Deacon <will@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Yicong Yang <yangyicong@hisilicon.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If two competing threads enter alloc_slab_obj_exts() and one of them
fails to allocate the object extension vector, it might override the
valid slab->obj_exts allocated by the other thread with
OBJEXTS_ALLOC_FAIL. This will cause the thread that lost this race and
expects a valid pointer to dereference a NULL pointer later on.
Update slab->obj_exts atomically using cmpxchg() to avoid
slab->obj_exts overrides by racing threads.
Thanks for Vlastimil and Suren's help with debugging.
Fixes: f7381b9116 ("slab: mark slab->obj_exts allocation failures unconditionally")
Cc: <stable@vger.kernel.org>
Suggested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Link: https://patch.msgid.link/20251021010353.1187193-1-hao.ge@linux.dev
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
When retbleed mitigation is disabled, the kernel already prints an info
message that the system is vulnerable. Recent code restructuring also
inadvertently led to RETBLEED_INTEL_MSG being printed as an error, which is
unnecessary as retbleed mitigation was already explicitly disabled (by config
option, cmdline, etc.).
Qualify this print statement so the warning is not printed unless an actual
retbleed mitigation was selected and is being disabled due to incompatibility
with spectre_v2.
Fixes: e3b78a7ad5 ("x86/bugs: Restructure retbleed mitigation")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220624
Signed-off-by: David Kaplan <david.kaplan@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://patch.msgid.link/20251003171936.155391-1-david.kaplan@amd.com
Resolve race conditions in timestamp events list handling between TX
and RX paths causing missed timestamps.
The current implementation uses a single events list for both TX and RX
timestamps. The am65_cpts_find_ts() function acquires the lock,
splices all events (TX as well as RX events) to a temporary list,
and releases the lock. This function performs matching of timestamps
for TX packets only. Before it acquires the lock again to put the
non-TX events back to the main events list, a concurrent RX
processing thread could acquire the lock (as observed in practice),
find an empty events list, and fail to attach timestamp to it,
even though a relevant event exists in the spliced list which is yet to
be restored to the main list.
Fix this by creating separate events lists to handle TX and RX
timestamps independently.
Fixes: c459f606f6 ("net: ethernet: ti: am65-cpts: Enable RX HW timestamp for PTP packets using CPTS FIFO")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20251016115755.1123646-1-a-garg7@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With enough debug options enabled, struct xfs_mount is larger
than 4k and thus NOFAIL allocations won't work for it.
xfs_init_fs_context is early in the mount process, and if we really
are out of memory there we'd better give up ASAP anyway.
Fixes: 7b77b46a61 ("xfs: use kmem functions for struct xfs_mount")
Reported-by: syzbot+359a67b608de1ef72f65@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
The MRU cache for open zones is unfortunately still not ideal, as it can
time out pretty easily when doing heavy I/O to hard disks using up most
or all open zones. One option would be to just increase the timeout,
but while looking into that I realized we're just better off caching it
indefinitely as there is no real downside to that once we don't hold a
reference to the cache open zone.
So switch the open zone to RCU freeing, and then stash the last used
open zone into inode->i_private. This helps to significantly reduce
fragmentation by keeping I/O localized to zones for workloads that
write using many open files to HDD.
Fixes: 4e4d520755 ("xfs: add the zoned space allocator")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
When GCD has no new work to handle, but read, write or reset commands
are outstanding, it currently busy loops, which is a bit suboptimal,
and can lead to softlockup warnings in case of stuck commands.
Change the code so that the task state is only set to running when work
is performed, which looks a bit tricky due to the design of the
reading/writing/resetting lists that contain both in-flight and finished
commands.
Fixes: 080d01c41d ("xfs: implement zoned garbage collection")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
When using page list framebuffer, and using RGB888 format, some
pixels can cross the page boundaries, and this case was not handled,
leading to writing 1 or 2 bytes on the next virtual address.
Add a check and a specific function to handle this case.
Fixes: c9ff280879 ("drm/panic: Add support to scanout buffer as array of pages")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20251009122955.562888-7-jfalempe@redhat.com
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
In the unlikely case that the screen is tiny, and smaller than the
font width, it leads to a divide by 0:
draw_line_with_wrap()
chars_per_row = sb->width / font->width = 0
line_wrap.len = line->len % chars_per_row;
This will trigger a divide by 0
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20251009122955.562888-6-jfalempe@redhat.com
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Currently, XFS_ONLINE_SCRUB_STATS selects DEBUG_FS. However, DEBUG_FS
is meant for debugging, and people may want to disable it on production
systems. Since commit 0ff51a1fd7 ("xfs: enable online fsck by
default in Kconfig")), XFS_ONLINE_SCRUB_STATS is enabled by default,
forcing DEBUG_FS enabled too.
Fix this by replacing the selection of DEBUG_FS by a dependency on
DEBUG_FS, which is what most other options controlling the gathering and
exposing of statistics do.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
When using a zoned realtime device, tightly packing of data blocks
belonging to multiple closed files into the same realtime group (RTG)
is very efficient at improving write performance. This is especially
true with SMR HDDs as this can reduce, and even suppress, disk head
seeks.
However, such tight packing does not make sense for large files that
require at least a full RTG. If tight packing placement is applied for
such files, the VM writeback thread switching between inodes result in
the large files to be fragmented, thus increasing the garbage collection
penalty later when the RTG needs to be reclaimed.
This problem can be avoided with a simple heuristic: if the size of the
inode being written back is at least equal to the RTG size, do not use
tight-packing. Modify xfs_zoned_pack_tight() to always return false in
this case.
With this change, a multi-writer workload writing files of 256 MB on a
file system backed by an SMR HDD with 256 MB zone size as a realtime
device sees all files occupying exactly one RTG (i.e. one device zone),
thus completely removing the heavy fragmentation observed without this
change.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Improve the description of the XFS_RT configuration option to document
that this option is required for zoned block devices.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
XDP programs can change the layout of an xdp_buff through
bpf_xdp_adjust_tail() and bpf_xdp_adjust_head(). Therefore, the driver
cannot assume the size of the linear data area nor fragments. Fix the
bug in mlx5 by generating skb according to xdp_buff after XDP programs
run.
Currently, when handling multi-buf XDP, the mlx5 driver assumes the
layout of an xdp_buff to be unchanged. That is, the linear data area
continues to be empty and fragments remain the same. This may cause
the driver to generate erroneous skb or triggering a kernel
warning. When an XDP program added linear data through
bpf_xdp_adjust_head(), the linear data will be ignored as
mlx5e_build_linear_skb() builds an skb without linear data and then
pull data from fragments to fill the linear data area. When an XDP
program has shrunk the non-linear data through bpf_xdp_adjust_tail(),
the delta passed to __pskb_pull_tail() may exceed the actual nonlinear
data size and trigger the BUG_ON in it.
To fix the issue, first record the original number of fragments. If the
number of fragments changes after the XDP program runs, rewind the end
fragment pointer by the difference and recalculate the truesize. Then,
build the skb with the linear data area matching the xdp_buff. Finally,
only pull data in if there is non-linear data and fill the linear part
up to 256 bytes.
Fixes: f52ac7028b ("net/mlx5e: RX, Add XDP multi-buffer support in Striding RQ")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
XDP programs can release xdp_buff fragments when calling
bpf_xdp_adjust_tail(). The driver currently assumes the number of
fragments to be unchanged and may generate skb with wrong truesize or
containing invalid frags. Fix the bug by generating skb according to
xdp_buff after the XDP program runs.
Fixes: ea5d49bdae ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The madvise implementation currently resets the SVM madvise if the
underlying CPU map is unmapped. This is in an attempt to mimic the
CPU madvise behaviour. However, it's not clear that this is a desired
behaviour since if the end app user relies on it for malloc()ed
objects or stack objects, it may not work as intended.
Instead of having the autoreset functionality being a direct
application-facing implicit UAPI, make the UMD explicitly choose
this behaviour if it wants to expose it by introducing
DRM_XE_VM_BIND_FLAG_MADVISE_AUTORESET, and add a semantics
description.
v2:
- Kerneldoc fixes. Fix a commit log message.
Fixes: a2eb8aec3e ("drm/xe: Reset VMA attributes to default in SVM garbage collector")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Cc: "Falkowski, John" <john.falkowski@intel.com>
Cc: "Mrozek, Michal" <michal.mrozek@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://lore.kernel.org/r/20251015170726.178685-2-thomas.hellstrom@linux.intel.com
(cherry picked from commit 59a2d3f38a)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
When splitting and restoring vmas for madvise, we only copied the
XE_VMA_SYSTEM_ALLOCATOR flag. That meant we lost flags for read_only,
dumpable and sparse (in case anyone would call madvise for the latter).
Instead, define a mask of relevant flags and ensure all are replicated,
To simplify this and make the code a bit less fragile, remove the
conversion to VMA_CREATE flags and instead just pass around the
gpuva flags after initial conversion from user-space.
Fixes: a2eb8aec3e ("drm/xe: Reset VMA attributes to default in SVM garbage collector")
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20251015170726.178685-1-thomas.hellstrom@linux.intel.com
(cherry picked from commit b3af8658ec)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
sctp_vrf.sh could fail:
TEST 12: bind vrf-2 & 1 in server, connect from client 1 & 2, N [FAIL]
not ok 1 selftests: net: sctp_vrf.sh # exit=3
The failure happens when the server bind in a new run conflicts with an
existing association from the previous run:
[1] ip netns exec $SERVER_NS ./sctp_hello server ...
[2] ip netns exec $CLIENT_NS ./sctp_hello client ...
[3] ip netns exec $SERVER_NS pkill sctp_hello ...
[4] ip netns exec $SERVER_NS ./sctp_hello server ...
It occurs if the client in [2] sends a message and closes immediately.
With the message unacked, no SHUTDOWN is sent. Killing the server in [3]
triggers a SHUTDOWN the client also ignores due to the unacked message,
leaving the old association alive. This causes the bind at [4] to fail
until the message is acked and the client responds to a second SHUTDOWN
after the server’s T2 timer expires (3s).
This patch fixes the issue by preventing the client from sending data.
Instead, the client blocks on recv() and waits for the server to close.
It also waits until both the server and the client sockets are fully
released in stop_server and wait_client before restarting.
Additionally, replace 2>&1 >/dev/null with -q in sysctl and grep, and
drop other redundant 2>&1 >/dev/null redirections, and fix a typo from
N to Y (connect successfully) in the description of the last test.
Fixes: a61bd7b9fe ("selftests: add a selftest for sctp vrf")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/be2dacf52d0917c4ba5e2e8c5a9cb640740ad2b6.1760731574.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull fsnotify fixes from Jan Kara:
- Stop-gap solution for a race between unmount of a filesystem with
fsnotify marks and someone inspecting fdinfo of fsnotify group with
those marks in procfs.
A proper solution is in the works but it will get a while to settle.
- Fix for non-decodable file handles (used by unprivileged apps using
fanotify)
* tag 'fsnotify_for_v6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs/notify: call exportfs_encode_fid with s_umount
expfs: Fix exportfs_can_encode_fh() for EXPORT_FH_FID
It is reported that commit 85975daeaa ("cpuidle: menu: Avoid discarding
useful information") led to a performance regression on Intel Jasper Lake
systems because it reduced the time spent by CPUs in idle state C7 which
is correlated to the maximum frequency the CPUs can get to because of an
average running power limit [1].
Before that commit, get_typical_interval() would have returned UINT_MAX
whenever it had been unable to make a high-confidence prediction which
had led to selecting the deepest available idle state too often and
both power and performance had been inadequate as a result of that on
some systems. However, this had not been a problem on systems with
relatively aggressive average running power limits, like the Jasper Lake
systems in question, because on those systems it was compensated by the
ability to run CPUs faster.
It was addressed by causing get_typical_interval() to return a number
based on the recent idle duration information available to it even if it
could not make a high-confidence prediction, but that clearly did not
take the possible correlation between idle power and available CPU
capacity into account.
For this reason, revert most of the changes made by commit 85975daeaa,
except for one cosmetic cleanup, and add a comment explaining the
rationale for returning UINT_MAX from get_typical_interval() when it
is unable to make a high-confidence prediction.
Fixes: 85975daeaa ("cpuidle: menu: Avoid discarding useful information")
Closes: https://lore.kernel.org/linux-pm/36iykr223vmcfsoysexug6s274nq2oimcu55ybn6ww4il3g3cv@cohflgdbpnq7/ [1]
Reported-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/3663603.iIbC2pHGDl@rafael.j.wysocki
The loop in tk_aux_sysfs_init() uses `i <= MAX_AUX_CLOCKS` as the
termination condition, which results in 9 iterations (i=0 to 8) when
MAX_AUX_CLOCKS is defined as 8. However, the kernel is designed to support
only up to 8 auxiliary clocks.
This off-by-one error causes the creation of a 9th sysfs entry that exceeds
the intended auxiliary clock range.
Fix the loop bound to use `i < MAX_AUX_CLOCKS` to ensure exactly 8
auxiliary clock entries are created, matching the design specification.
Fixes: 7b95663a3d ("timekeeping: Provide interface to control auxiliary clocks")
Signed-off-by: Haofeng Li <lihaofeng@kylinos.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/tencent_2376993D9FC06A3616A4F981B3DE1C599607@qq.com
Separating the panic allocation from framebuffer allocation in commit
729c5f7ffa ("drm/{i915,xe}/panic: move framebuffer allocation where it
belongs") failed to deallocate the panic structure anywhere.
The fix is two-fold. First, free the panic structure in
intel_user_framebuffer_destroy() in the general case. Second, move the
panic allocation later to intel_framebuffer_init() to not leak the panic
structure in error paths (if any, now or later) between
intel_framebuffer_alloc() and intel_framebuffer_init().
v2: Rebase
Fixes: 729c5f7ffa ("drm/{i915,xe}/panic: move framebuffer allocation where it belongs")
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Maarten Lankhorst <dev@lankhorst.se>
Reported-by: Michał Grzelak <michal.grzelak@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Michał Grzelak <michal.grzelak@intel.com> # v1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20251015095135.2183415-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 8f8ef09fcf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The following NULL pointer dereference is encountered on mount of resctrl fs
after booting a system that supports assignable counters with the
"rdt=!mbmtotal,!mbmlocal" kernel parameters:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:mbm_cntr_get
Call Trace:
rdtgroup_assign_cntr_event
rdtgroup_assign_cntrs
rdt_get_tree
Specifying the kernel parameter "rdt=!mbmtotal,!mbmlocal" effectively disables
the legacy X86_FEATURE_CQM_MBM_TOTAL and X86_FEATURE_CQM_MBM_LOCAL features
and the MBM events they represent. This results in the per-domain MBM event
related data structures to not be allocated during early initialization.
resctrl fs initialization follows by implicitly enabling both MBM total and
local events on a system that supports assignable counters (mbm_event mode),
but this enabling occurs after the per-domain data structures have been
created.
After booting, resctrl fs assumes that an enabled event can access all its
state. This results in NULL pointer dereference when resctrl attempts to
access the un-allocated structures of an enabled event.
Remove the late MBM event enabling from resctrl fs.
This leaves a problem where the X86_FEATURE_CQM_MBM_TOTAL and
X86_FEATURE_CQM_MBM_LOCAL features may be disabled while assignable counter
(mbm_event) mode is enabled without any events to support. Switching between
the "default" and "mbm_event" mode without any events is not practical.
Create a dependency between the X86_FEATURE_{CQM_MBM_TOTAL,CQM_MBM_LOCAL} and
X86_FEATURE_ABMC (assignable counter) hardware features. An x86 system that
supports assignable counters now requires support of X86_FEATURE_CQM_MBM_TOTAL
or X86_FEATURE_CQM_MBM_LOCAL.
This ensures all needed MBM related data structures are created before use and
that it is only possible to switch between "default" and "mbm_event" mode when
the same events are available in both modes. This dependency does not exist in
the hardware but this usage of these feature settings work for known systems.
[ bp: Massage commit message. ]
Fixes: 13390861b4 ("x86,fs/resctrl: Detect Assignable Bandwidth Monitoring feature details")
Co-developed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://patch.msgid.link/a62e6ac063d0693475615edd213d5be5e55443e6.1760560934.git.babu.moger@amd.com
This reverts commit 4660e50cf8.
Commit f6fd357f7a ("PCI: dwc: Prepare the driver for enabling ECAM
mechanism using iATU 'CFG Shift Feature'") enabled ECAM access by using
the config space start as DBI address.
However, this approach breaks vendor drivers that rely on the DBI address
for internal accesses, especially when the vendor config space is 256MB
aligned.
To resolve this, avoid using the DBI as the start of config space and
instead introduce a custom ECAM PCI ops implementation.
Revert the qcom specific ECAM preparation logic in 4660e50cf8 ("PCI:
qcom: Prepare for the DWC ECAM enablement") since it's no longer necessary.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251017-ecam_fix-v1-2-f6faa3d0edf3@oss.qualcomm.com
When the vendor configuration space is 256MB aligned, the DesignWare PCIe
host driver enables ECAM access and sets the DBI base to the start of the
config space. This causes vendor drivers to incorrectly program iATU
regions, as they rely on the DBI address for internal accesses.
To fix this, avoid overwriting the DBI base when ECAM is enabled. Instead,
introduce a custom pci_ops that accesses the DBI region directly for the
root bus and uses ECAM for other buses.
Fixes: f6fd357f7a ("PCI: dwc: Prepare the driver for enabling ECAM mechanism using iATU 'CFG Shift Feature'")
Reported-by: Ron Economos <re@w6rz.net>
Closes: https://lore.kernel.org/all/eac81c57-1164-4d74-a1b4-6f353c577731@w6rz.net/
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Ron Economos <re@w6rz.net>
Link: https://patch.msgid.link/20251017-ecam_fix-v1-1-f6faa3d0edf3@oss.qualcomm.com
sock_{send,recv}msg() internally calls security_socket_{send,recv}msg(),
which does security checks (e.g. SELinux) for socket access against the
current task. However, _sock_xmit() in drivers/block/nbd.c may be called
indirectly from a userspace syscall, where the NBD socket access would
be incorrectly checked against the calling userspace task (which simply
tries to read/write a file that happens to reside on an NBD device).
To fix this, temporarily override creds to kernel ones before calling
the sock_*() functions. This allows the security modules to recognize
this as internal access by the kernel, which will normally be allowed.
A way to trigger the issue is to do the following (on a system with
SELinux set to enforcing):
### Create nbd device:
truncate -s 256M /tmp/testfile
nbd-server localhost:10809 /tmp/testfile
### Connect to the nbd server:
nbd-client localhost
### Create mdraid array
mdadm --create -l 1 -n 2 /dev/md/testarray /dev/nbd0 missing
After these steps, assuming the SELinux policy doesn't allow the
unexpected access pattern, errors will be visible on the kernel console:
[ 142.204243] nbd0: detected capacity change from 0 to 524288
[ 165.189967] md: async del_gendisk mode will be removed in future, please upgrade to mdadm-4.5+
[ 165.252299] md/raid1:md127: active with 1 out of 2 mirrors
[ 165.252725] md127: detected capacity change from 0 to 522240
[ 165.255434] block nbd0: Send control failed (result -13)
[ 165.255718] block nbd0: Request send failed, requeueing
[ 165.256006] block nbd0: Dead connection, failed to find a fallback
[ 165.256041] block nbd0: Receive control failed (result -32)
[ 165.256423] block nbd0: shutting down sockets
[ 165.257196] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.257736] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.258263] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.259376] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.259920] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.260628] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.261661] ldm_validate_partition_table(): Disk read failed.
[ 165.262108] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.262769] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.263697] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.264412] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.265412] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.265872] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.266378] I/O error, dev nbd0, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.267168] Buffer I/O error on dev md127, logical block 0, async page read
[ 165.267564] md127: unable to read partition table
[ 165.269581] I/O error, dev nbd0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.269960] Buffer I/O error on dev nbd0, logical block 0, async page read
[ 165.270316] I/O error, dev nbd0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.270913] Buffer I/O error on dev nbd0, logical block 0, async page read
[ 165.271253] I/O error, dev nbd0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 165.271809] Buffer I/O error on dev nbd0, logical block 0, async page read
[ 165.272074] ldm_validate_partition_table(): Disk read failed.
[ 165.272360] nbd0: unable to read partition table
[ 165.289004] ldm_validate_partition_table(): Disk read failed.
[ 165.289614] nbd0: unable to read partition table
The corresponding SELinux denial on Fedora/RHEL will look like this
(assuming it's not silenced):
type=AVC msg=audit(1758104872.510:116): avc: denied { write } for pid=1908 comm="mdadm" laddr=::1 lport=32772 faddr=::1 fport=10809 scontext=system_u:system_r:mdadm_t:s0-s0:c0.c1023 tcontext=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 tclass=tcp_socket permissive=0
The respective backtrace looks like this:
@security[mdadm, -13,
handshake_exit+221615650
handshake_exit+221615650
handshake_exit+221616465
security_socket_sendmsg+5
sock_sendmsg+106
handshake_exit+221616150
sock_sendmsg+5
__sock_xmit+162
nbd_send_cmd+597
nbd_handle_cmd+377
nbd_queue_rq+63
blk_mq_dispatch_rq_list+653
__blk_mq_do_dispatch_sched+184
__blk_mq_sched_dispatch_requests+333
blk_mq_sched_dispatch_requests+38
blk_mq_run_hw_queue+239
blk_mq_dispatch_plug_list+382
blk_mq_flush_plug_list.part.0+55
__blk_flush_plug+241
__submit_bio+353
submit_bio_noacct_nocheck+364
submit_bio_wait+84
__blkdev_direct_IO_simple+232
blkdev_read_iter+162
vfs_read+591
ksys_read+95
do_syscall_64+92
entry_SYSCALL_64_after_hwframe+120
]: 1
The issue has started to appear since commit 060406c61c ("block: add
plug while submitting IO").
Cc: Ming Lei <ming.lei@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2348878
Fixes: 060406c61c ("block: add plug while submitting IO")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The negation operator is incorrectly placed outside the unlikely()
macro:
if (!unlikely(iwa))
This inverts the compiler branch prediction hint, marking the NULL case
as likely instead of unlikely. The intent is to indicate that allocation
failures are rare, consistent with common kernel patterns.
Moving the negation inside unlikely():
if (unlikely(!iwa))
Fixes: 2b4fc4cd43 ("io_uring/waitid: setup async data in the prep handler")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the commit c1f3f9797c ("can: netlink: can_changelink(): fix NULL
pointer deref of struct can_priv::do_set_mode"), the automatic restart
delay can only be set for devices that implement the restart handler struct
can_priv::do_set_mode. As it makes no sense to configure a automatic
restart for devices that doesn't support it.
However, since systemd commit 13ce5d4632e3 ("network/can: properly handle
CAN.RestartSec=0") [1], systemd-networkd correctly handles a restart delay
of "0" (i.e. the restart is disabled). Which means that a disabled restart
is always configured in the kernel.
On systems with both changes active this causes that CAN interfaces that
don't implement a restart handler cannot be brought up by systemd-networkd.
Solve this problem by allowing a delay of "0" to be configured, even if the
device does not implement a restart handler.
[1] 13ce5d4632
Cc: stable@vger.kernel.org
Cc: Andrei Lalaev <andrey.lalaev@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251020-certain-arrogant-vole-of-sunshine-141841-mkl@pengutronix.de
Fixes: c1f3f9797c ("can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode")
Link: https://patch.msgid.link/20251020-netlink-fix-restart-v1-1-3f53c7f8520b@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The IB_WR_REG_MR and IB_WR_LOCAL_INV operations for smbdirect_mr_io
structures should never fail because the submission or completion queues
are too small. So we allocate more send_wr depending on the (local) max
number of MRs.
While there also add additional space for ib_drain_qp().
This should make sure ib_post_send() will never fail
because the submission queue is full.
Fixes: f198186aa9 ("CIFS: SMBD: Establish SMB Direct connection")
Fixes: cc55f65dd3 ("smb: client: make use of common smbdirect_socket_parameters")
Cc: stable@vger.kernel.org
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Handling of errors when reading status, temperature, and humidity returns
the error number as negative attribute value. Fix it up by returning
the error as return value.
Fixes: a0ac418c60 ("hwmon: (sht3x) convert some of sysfs interface to hwmon")
Cc: JuenKit Yip <JuenKit_Yip@hotmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver allocates memory for sensor data using devm_kzalloc(), but
did not check if the allocation succeeded. In case of memory allocation
failure, dereferencing the NULL pointer would lead to a kernel crash.
Add a NULL pointer check and return -ENOMEM to handle allocation failure
properly.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Fixes: 08ebc9def7 ("hwmon: Add Congatec Board Controller monitoring driver")
Reviewed-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20251017063414.1557447-1-liqiang01@kylinos.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull scheduler fixes from Borislav Petkov:
- Make sure the check for lost pelt idle time is done unconditionally
to have correct lost idle time accounting
- Stop the deadline server task before a CPU goes offline
* tag 'sched_urgent_for_v6.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix pelt lost idle time detection
sched/deadline: Stop dl_server before CPU goes offline
Pull perf fixes from Borislav Petkov:
- Make sure perf reporting works correctly in setups using
overlayfs or FUSE
- Move the uprobe optimization to a better location logically
* tag 'perf_urgent_for_v6.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix MMAP2 event device with backing files
perf/core: Fix MMAP event path names with backing files
perf/core: Fix address filter match with backing files
uprobe: Move arch_uprobe_optimize right after handlers execution
Pull x86 fixes from Borislav Petkov:
- Reset the why-the-system-rebooted register on AMD to avoid stale bits
remaining from previous boots
- Add a missing barrier in the TLB flushing code to prevent erroneously
not flushing a TLB generation
- Make sure cpa_flush() does not overshoot when computing the end range
of a flush region
- Fix resctrl bandwidth counting on AMD systems when the amount of
monitoring groups created exceeds the number the hardware can track
* tag 'x86_urgent_for_v6.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Prevent reset reasons from being retained across reboot
x86/mm: Fix SMP ordering in switch_mm_irqs_off()
x86/mm: Fix overflow in __cpa_addr()
x86/resctrl: Fix miscount of bandwidth event when reactivating previously unavailable RMID
Pull rustfmt fixes from Miguel Ojeda:
"Rust 'rustfmt' cleanup
'rustfmt', by default, formats imports in a way that is prone to
conflicts while merging and rebasing, since in some cases it condenses
several items into the same line.
Document in our guidelines that we will handle this for the moment
with the trailing empty comment workaround and make the tree
'rustfmt'-clean again"
* tag 'rust-rustfmt' of git://git.kernel.org/pub/scm/linux/kernel/git/ojeda/linux:
rust: bitmap: fix formatting
rust: cpufreq: fix formatting
rust: alloc: employ a trailing comment to keep vertical layout
docs: rust: add section on imports formatting
Pull tpm fix from Jarkko Sakkinen:
"Correct the state transitions for ARM FF-A to match the spec and how
tpm_crb behaves on other platforms"
* tag 'tpmdd-next-v6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm_crb: Add idle support for the Arm FF-A start method
Pull pci fixes from Bjorn Helgaas:
- Search for MSI Capability with correct ID to fix an MSI regression on
platforms with Cadence IP (Hans Zhang)
- Revert early bridge resource set up to fix resource assignment
failures that broke at least alpha boot and Snapdragon ath12k WiFi
(Ilpo Järvinen)
- Implement VMD .irq_startup()/.irq_shutdown() to fix IRQ issues that
caused boot crashes and broken devices below VMD (Inochi Amaoto)
- Select CONFIG_SCREEN_INFO on X86 to fix black screen on boot when
SCREEN_INFO not selected (Mario Limonciello)
* tag 'pci-v6.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/VGA: Select SCREEN_INFO on X86
PCI: vmd: Override irq_startup()/irq_shutdown() in vmd_init_dev_msi_info()
PCI: Revert early bridge resource set up
PCI: cadence: Search for MSI Capability with correct ID
Pull Compute Express Link fixes from Dave Jiang:
"A small collection of CXL fixes. In addition to some misc fixes for
the CXL subsystem, a number of fixes for CXL extended linear cache
support are included to make it functional again.
- Avoid missing port component registers setup due to dport
enumeration failure
- Add check for no entries in cxl_feature_info to address accessing
invalid pointer.
- Use %pa printk format to emit resource_size_t in
validate_region_offset()
CXL extended linear cache support fixes:
- Fix setup of memory resource in cxl_acpi_set_cache_size()
- Set range param for region_res_match_cxl_range() as const
(addresses a compile warning for match_region_by_range() fix)
- Fix match_region_by_range() to use region_res_match_cxl_range()
- Subtract to find an hpa_alias0 in cxl_poison events to correct the
alias math calculation"
* tag 'cxl-fixes-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/trace: Subtract to find an hpa_alias0 in cxl_poison events
cxl/region: Use %pa printk format to emit resource_size_t
cxl: Fix match_region_by_range() to use region_res_match_cxl_range()
cxl: Set range param for region_res_match_cxl_range() as const
cxl/acpi: Fix setup of memory resource in cxl_acpi_set_cache_size()
cxl/features: Add check for no entries in cxl_feature_info
cxl/port: Avoid missing port component registers setup
Pull bpf fixes from Alexei Starovoitov:
- Replace bpf_map_kmalloc_node() with kmalloc_nolock() to fix kmemleak
imbalance in tracking of bpf_async_cb structures (Alexei Starovoitov)
- Make selftests/bpf arg_parsing.c more robust to errors (Andrii
Nakryiko)
- Fix redefinition of 'off' as different kind of symbol when I40E
driver is builtin (Brahmajit Das)
- Do not disable preemption in bpf_test_run (Sahil Chandna)
- Fix memory leak in __lookup_instance error path (Shardul Bankar)
- Ensure test data is flushed to disk before reading it (Xing Guo)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Fix redefinition of 'off' as different kind of symbol
bpf: Do not disable preemption in bpf_test_run().
bpf: Fix memory leak in __lookup_instance error path
selftests: arg_parsing: Ensure data is flushed to disk before reading.
bpf: Replace bpf_map_kmalloc_node() with kmalloc_nolock() to allocate bpf_async_cb structures.
selftests/bpf: make arg_parsing.c more robust to crashes
bpf: test_run: Fix ctx leak in bpf_prog_test_run_xdp error path
Pull exfat fixes from Namjae Jeon:
- Fix out-of-bounds in FS_IOC_SETFSLABEL
- Add validation for stream entry size to prevent infinite loop
* tag 'exfat-for-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: fix out-of-bounds in exfat_nls_to_ucs2()
exfat: fix improper check of dentry.stream.valid_size
Pull NFS client fixes from Anna Schumaker:
- Fix for FlexFiles mirror->dss allocation
- Apply delay_retrans to async operations
- Check if suid/sgid is cleared after a write when needed
- Fix setting the state renewal timer for early mounts after a reboot
* tag 'nfs-for-6.18-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS4: Fix state renewals missing after boot
NFS: check if suid/sgid was cleared after a write as needed
NFS4: Apply delay_retrans to async operations
NFSv4/flexfiles: fix to allocate mirror->dss before use
Pull smb client fixes from Steve French:
"smb client fixes, security and smbdirect improvements, and some minor cleanup:
- Important OOB DFS fix
- Fix various potential tcon refcount leaks
- smbdirect (RDMA) fixes (following up from test event a few weeks
ago):
- Fixes to improve and simplify handling of memory lifetime of
smbdirect_mr_io structures, when a connection gets disconnected
- Make sure we really wait to reach SMBDIRECT_SOCKET_DISCONNECTED
before destroying resources
- Make sure the send/recv submission/completion queues are large
enough to avoid ib_post_send() from failing under pressure
- convert cifs.ko to use the recommended crypto libraries (instead of
crypto_shash), this also can improve performance
- Three small cleanup patches"
* tag '6.18-rc1-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: (24 commits)
smb: client: Consolidate cmac(aes) shash allocation
smb: client: Remove obsolete crypto_shash allocations
smb: client: Use HMAC-MD5 library for NTLMv2
smb: client: Use MD5 library for SMB1 signature calculation
smb: client: Use MD5 library for M-F symlink hashing
smb: client: Use HMAC-SHA256 library for SMB2 signature calculation
smb: client: Use HMAC-SHA256 library for key generation
smb: client: Use SHA-512 library for SMB3.1.1 preauth hash
cifs: parse_dfs_referrals: prevent oob on malformed input
smb: client: Fix refcount leak for cifs_sb_tlink
smb: client: let smbd_destroy() wait for SMBDIRECT_SOCKET_DISCONNECTED
smb: move some duplicate definitions to common/cifsglob.h
smb: client: let destroy_mr_list() keep smbdirect_mr_io memory if registered
smb: client: let destroy_mr_list() call ib_dereg_mr() before ib_dma_unmap_sg()
smb: client: call ib_dma_unmap_sg if mr->sgt.nents is not 0
smb: client: improve logic in smbd_deregister_mr()
smb: client: improve logic in smbd_register_mr()
smb: client: improve logic in allocate_mr_list()
smb: client: let destroy_mr_list() remove locked from the list
smb: client: let destroy_mr_list() call list_del(&mr->list)
...
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix the handling of ZCR_EL2 in NV VMs
- Pick the correct translation regime when doing a PTW on the back of
a SEA
- Prevent userspace from injecting an event into a vcpu that isn't
initialised yet
- Move timer save/restore to the sysreg handling code, fixing EL2
timer access in the process
- Add FGT-based trapping of MDSCR_EL1 to reduce the overhead of debug
- Fix trapping configuration when the host isn't GICv3
- Improve the detection of HCR_EL2.E2H being RES1
- Drop a spurious 'break' statement in the S1 PTW
- Don't try to access SPE when owned by EL3
Documentation updates:
- Document the failure modes of event injection
- Document that a GICv3 guest can be created on a GICv5 host with
FEAT_GCIE_LEGACY
Selftest improvements:
- Add a selftest for the effective value of HCR_EL2.AMO
- Address build warning in the timer selftest when building with
clang
- Teach irqfd selftests about non-x86 architectures
- Add missing sysregs to the set_id_regs selftest
- Fix vcpu allocation in the vgic_lpi_stress selftest
- Correctly enable interrupts in the vgic_lpi_stress selftest
x86:
- Expand the KVM_PRE_FAULT_MEMORY selftest to add a regression test
for the bug fixed by commit 3ccbf6f470 ("KVM: x86/mmu: Return
-EAGAIN if userspace deletes/moves memslot during prefault")
- Don't try to get PMU capabilities from perf when running a CPU with
hybrid CPUs/PMUs, as perf will rightly WARN.
guest_memfd:
- Rework KVM_CAP_GUEST_MEMFD_MMAP (newly introduced in 6.18) into a
more generic KVM_CAP_GUEST_MEMFD_FLAGS
- Add a guest_memfd INIT_SHARED flag and require userspace to
explicitly set said flag to initialize memory as SHARED,
irrespective of MMAP.
The behavior merged in 6.18 is that enabling mmap() implicitly
initializes memory as SHARED, which would result in an ABI
collision for x86 CoCo VMs as their memory is currently always
initialized PRIVATE.
- Allow mmap() on guest_memfd for x86 CoCo VMs, i.e. on VMs with
private memory, to enable testing such setups, i.e. to hopefully
flush out any other lurking ABI issues before 6.18 is officially
released.
- Add testcases to the guest_memfd selftest to cover guest_memfd
without MMAP, and host userspace accesses to mmap()'d private
memory"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (46 commits)
arm64: Revamp HCR_EL2.E2H RES1 detection
KVM: arm64: nv: Use FGT write trap of MDSCR_EL1 when available
KVM: arm64: Compute per-vCPU FGTs at vcpu_load()
KVM: arm64: selftests: Fix misleading comment about virtual timer encoding
KVM: arm64: selftests: Add an E2H=0-specific configuration to get_reg_list
KVM: arm64: selftests: Make dependencies on VHE-specific registers explicit
KVM: arm64: Kill leftovers of ad-hoc timer userspace access
KVM: arm64: Fix WFxT handling of nested virt
KVM: arm64: Move CNT*CT_EL0 userspace accessors to generic infrastructure
KVM: arm64: Move CNT*_CVAL_EL0 userspace accessors to generic infrastructure
KVM: arm64: Move CNT*_CTL_EL0 userspace accessors to generic infrastructure
KVM: arm64: Add timer UAPI workaround to sysreg infrastructure
KVM: arm64: Make timer_set_offset() generally accessible
KVM: arm64: Replace timer context vcpu pointer with timer_id
KVM: arm64: Introduce timer_context_to_vcpu() helper
KVM: arm64: Hide CNTHV_*_EL2 from userspace for nVHE guests
Documentation: KVM: Update GICv3 docs for GICv5 hosts
KVM: arm64: gic-v3: Only set ICH_HCR traps for v2-on-v3 or v3 guests
KVM: arm64: selftests: Actually enable IRQs in vgic_lpi_stress
KVM: arm64: selftests: Allocate vcpus with correct size
...
Pull powerpc fixes from Madhavan Srinivasan:
- Fix to handle NULL pointer dereference at irq domain teardown
- Fix for handling extraction of struct xive_irq_data
- Fix to skip parameter area allocation when fadump disabled
Thanks to Ganesh Goudar, Hari Bathini, Nam Cao, Ritesh Harjani (IBM),
Sourabh Jain, and Venkat Rao Bagalkote,
* tag 'powerpc-6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/fadump: skip parameter area allocation when fadump is disabled
powerpc, ocxl: Fix extraction of struct xive_irq_data
powerpc/pseries/msi: Fix NULL pointer dereference at irq domain teardown
Pull slab fixes from Vlastimil Babka:
- Fixes for two bugs that can be triggered when debugging options are
enabled (Hao Ge, Vlastimil Babka)
* tag 'slab-for-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: reset slab->obj_ext when freeing and it is OBJEXTS_ALLOC_FAIL
slab: fix clearing freelist in free_deferred_objects()
Resolve this smatch warning:
arch/riscv/kernel/sys_hwprobe.c:50 hwprobe_arch_id() error: uninitialized symbol 'cpu_id'.
This could happen if hwprobe_arch_id() was called with a key ID of
something other than MVENDORID, MIMPID, and MARCHID. This does not
happen in the current codebase. The only caller of hwprobe_arch_id()
is a function that only passes one of those three key IDs.
For the sake of reducing static analyzer warning noise, and in the
unlikely event that hwprobe_arch_id() is someday called with some
other key ID, validate hwprobe_arch_id()'s input to ensure that
'cpu_id' is always initialized before use.
Fixes: ea3de9ce8a ("RISC-V: Add a syscall for HW probing")
Cc: Evan Green <evan@rivosinc.com>
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Link: https://lore.kernel.org/r/cf5a13ec-19d0-9862-059b-943f36107bf3@kernel.org
In has_thead_homogeneous_vlenb(), smatch detected that the vlenb variable
could be used while uninitialized. It appears that this could happen if
no CPUs described in DT have the "thead,vlenb" property.
Fix by initializing vlenb to 0, which will keep thead_vlenb_of set to 0
(as it was statically initialized). This in turn will cause
riscv_v_setup_vsize() to fall back to CSR probing - the desired result if
thead,vlenb isn't provided in the DT data.
While here, fix a nearby comment typo.
Cc: stable@vger.kernel.org
Cc: Charlie Jenkins <charlie@rivosinc.com>
Fixes: 377be47f90 ("riscv: vector: Use vlenb from DT for thead")
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Link: https://lore.kernel.org/r/22674afb-2fe8-2a83-1818-4c37bd554579@kernel.org
Pull amd-pstate 6.18 content (10/15/25) from Mario Limonciello:
"Fix for EPP value in wrong state after S4"
* tag 'amd-pstate-v6.18-2025-10-15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/superm1/linux:
cpufreq/amd-pstate: Fix a regression leading to EPP 0 after hibernate
According to the CRB over FF-A specification [1], a TPM that implements
the ABI must comply with the TCG PTP specification. This requires support
for the Idle and Ready states.
This patch implements CRB control area requests for goIdle and
cmdReady on FF-A based TPMs.
The FF-A message used to notify the TPM of CRB updates includes a
locality parameter, which provides a hint to the TPM about which
locality modified the CRB. This patch adds a locality parameter
to __crb_go_idle() and __crb_cmd_ready() to support this.
[1] https://developer.arm.com/documentation/den0138/latest/
Signed-off-by: Stuart Yoder <stuart.yoder@arm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
KVM x86 fixes for 6.18:
- Expand the KVM_PRE_FAULT_MEMORY selftest to add a regression test for the
bug fixed by commit 3ccbf6f470 ("KVM: x86/mmu: Return -EAGAIN if userspace
deletes/moves memslot during prefault")
- Don't try to get PMU capabbilities from perf when running a CPU with hybrid
CPUs/PMUs, as perf will rightly WARN.
- Rework KVM_CAP_GUEST_MEMFD_MMAP (newly introduced in 6.18) into a more
generic KVM_CAP_GUEST_MEMFD_FLAGS
- Add a guest_memfd INIT_SHARED flag and require userspace to explicitly set
said flag to initialize memory as SHARED, irrespective of MMAP. The
behavior merged in 6.18 is that enabling mmap() implicitly initializes
memory as SHARED, which would result in an ABI collision for x86 CoCo VMs
as their memory is currently always initialized PRIVATE.
- Allow mmap() on guest_memfd for x86 CoCo VMs, i.e. on VMs with private
memory, to enable testing such setups, i.e. to hopefully flush out any
other lurking ABI issues before 6.18 is officially released.
- Add testcases to the guest_memfd selftest to cover guest_memfd without MMAP,
and host userspace accesses to mmap()'d private memory.
The hwprobe vDSO data for some keys, like MISALIGNED_VECTOR_PERF,
is determined by an asynchronous kthread. This can create a race
condition where the kthread finishes after the vDSO data has
already been populated, causing userspace to read stale values.
To fix this race, a new 'ready' flag is added to the vDSO data,
initialized to 'false' during arch_initcall_sync. This flag is
checked by both the vDSO's user-space code and the riscv_hwprobe
syscall. The syscall serves as a one-time gate, using a completion
to wait for any pending probes before populating the data and
setting the flag to 'true', thus ensuring userspace reads fresh
values on its first request.
Reported-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Closes: https://lore.kernel.org/linux-riscv/760d637b-b13b-4518-b6bf-883d55d44e7f@irq.a4lg.com/
Fixes: e7c9d66e31 ("RISC-V: Report vector unaligned access speed hwprobe")
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Co-developed-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Jingwei Wang <wangjingwei@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250811142035.105820-1-wangjingwei@iscas.ac.cn
[pjw@kernel.org: fix checkpatch issues]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
The pgprot_dmacoherent() is used when allocating memory for
non-coherent devices and by default pgprot_dmacoherent() is
same as pgprot_noncached() unless architecture overrides it.
Currently, there is no pgprot_dmacoherent() definition for
RISC-V hence non-coherent device memory is being mapped as
IO thereby making CPU access to such memory slow.
Define pgprot_dmacoherent() to be same as pgprot_writecombine()
for RISC-V so that CPU access non-coherent device memory as
NOCACHE which is better than accessing it as IO.
Fixes: ff689fd21c ("riscv: add RISC-V Svpbmt extension support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Han Gao <rabenda.cn@gmail.com>
Tested-by: Guo Ren (Alibaba DAMO Academy) <guoren@kernel.org>
Link: https://lore.kernel.org/r/20250820152316.1012757-1-apatel@ventanamicro.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
When splitting the RTL8221B-VM-CG into C22 and C45 variants, the name was
accidentally changed to RTL8221B-VN-CG. This patch brings back the previous
part number.
Fixes: ad5ce743a6 ("net: phy: realtek: Add driver instances for rtl8221b via Clause 45")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016192325.2306757-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit increased the needed headroom to account for
alignment. This means that the size required to always align a Tx buffer
was added inside the dpaa2_eth_needed_headroom() function. By doing
that, a manual adjustment of the pointer passed to PTR_ALIGN() was no
longer correct since the 'buffer_start' variable was already pointing
to the start of the skb's memory.
The behavior of the dpaa2-eth driver without this patch was to drop
frames on Tx even when the headroom was matching the 128 bytes
necessary. Fix this by removing the manual adjust of 'buffer_start' from
the PTR_MODE call.
Closes: https://lore.kernel.org/netdev/70f0dcd9-1906-4d13-82df-7bbbbe7194c6@app.fastmail.com/T/#u
Fixes: f422abe3f2 ("dpaa2-eth: increase the needed headroom to account for alignment")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016135807.360978-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENETC RX ring uses the page halves flipping mechanism, each page is
split into two halves for the RX ring to use. And ENETC_RXB_TRUESIZE is
defined to 2048 to indicate the size of half a page. However, the page
size is configurable, for ARM64 platform, PAGE_SIZE is default to 4K,
but it could be configured to 16K or 64K.
When PAGE_SIZE is set to 16K or 64K, ENETC_RXB_TRUESIZE is not correct,
and the RX ring will always use the first half of the page. This is not
consistent with the description in the relevant kernel doc and commit
messages.
This issue is invisible in most cases, but if users want to increase
PAGE_SIZE to receive a Jumbo frame with a single buffer for some use
cases, it will not work as expected, because the buffer size of each
RX BD is fixed to 2048 bytes.
Based on the above two points, we expect to correct ENETC_RXB_TRUESIZE
to (PAGE_SIZE >> 1), as described in the comment.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20251016080131.3127122-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After applying the workaround for err050089, the LS1028A platform
experiences RCU stalls on RT kernel. This issue is caused by the
recursive acquisition of the read lock enetc_mdio_lock. Here list some
of the call stacks identified under the enetc_poll path that may lead to
a deadlock:
enetc_poll
-> enetc_lock_mdio
-> enetc_clean_rx_ring OR napi_complete_done
-> napi_gro_receive
-> enetc_start_xmit
-> enetc_lock_mdio
-> enetc_map_tx_buffs
-> enetc_unlock_mdio
-> enetc_unlock_mdio
After enetc_poll acquires the read lock, a higher-priority writer attempts
to acquire the lock, causing preemption. The writer detects that a
read lock is already held and is scheduled out. However, readers under
enetc_poll cannot acquire the read lock again because a writer is already
waiting, leading to a thread hang.
Currently, the deadlock is avoided by adjusting enetc_lock_mdio to prevent
recursive lock acquisition.
Fixes: 6d36ecdbc4 ("net: enetc: take the MDIO lock only once per NAPI poll cycle")
Signed-off-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Acked-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251015021427.180757-1-jianpeng.chang.cn@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull arm64 fixes from Catalin Marinas:
- Explicitly encode the XZR register if the value passed to
write_sysreg_s() is 0.
The GIC CDEOI instruction is encoded as a system register write with
XZR as the source register. However, clang does not honour the "Z"
register constraint, leading to incorrect code generation
- Ensure the interrupts (DAIF.IF) are unmasked when completing
single-step of a suspended breakpoint before calling
exit_to_user_mode().
With pseudo-NMIs, interrupts are (additionally) masked at the PMR_EL1
register, handled by local_irq_*()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: debug: always unmask interrupts in el0_softstp()
arm64/sysreg: Fix GIC CDEOI instruction encoding
Pull RISC-V fixes from Paul Walmsley:
- Disable CFI with Rust for any platform other than x86 and ARM64
- Keep task mm_cpumasks up-to-date to avoid triggering M-mode firmware
warnings if the kernel tries to send an IPI to an offline CPU
- Improve kprobe address validation performance and avoid desyncs
(following x86)
- Avoid duplicate device probes by avoiding DT hardware probing when
ACPI is enabled in early boot
- Use the correct set of dependencies for
CONFIG_ARCH_HAS_ELF_CORE_EFLAGS, avoiding an allnoconfig warning
- Fix a few other minor issues
* tag 'riscv-for-linux-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: kprobes: convert one final __ASSEMBLY__ to __ASSEMBLER__
riscv: Respect dependencies of ARCH_HAS_ELF_CORE_EFLAGS
riscv: acpi: avoid errors caused by probing DT devices when ACPI is used
riscv: kprobes: Fix probe address validation
riscv: entry: fix typo in comment 'instruciton' -> 'instruction'
RISC-V: clear hot-unplugged cores from all task mm_cpumasks to avoid rfence errors
riscv: kgdb: Ensure that BUFMAX > NUMREGBYTES
rust: cfi: only 64-bit arm and x86 support CFI_CLANG
Regardless of the DeviceContext of a device, we can't give any
guarantees about the DeviceContext of its parent device.
This is very subtle, since it's only caused by a simple typo, i.e.
Self::from_raw(parent)
which preserves the DeviceContext in this case, vs.
Device::from_raw(parent)
which discards the DeviceContext.
(I should have noticed it doing the correct thing in auxiliary::Device
subsequently, but somehow missed it.)
Hence, fix both Device::parent() and auxiliary::Device::parent().
Cc: stable@vger.kernel.org
Fixes: a4c9f71e34 ("rust: device: implement Device::parent()")
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
This fixes the following build error
CLNG-BPF [test_progs] verifier_global_ptr_args.bpf.o
progs/verifier_global_ptr_args.c:228:5: error: redefinition of 'off' as
different kind of symbol
228 | u32 off;
| ^
The symbol 'off' was previously defined in
tools/testing/selftests/bpf/tools/include/vmlinux.h, which includes an
enum i40e_ptp_gpio_pin_state from
drivers/net/ethernet/intel/i40e/i40e_ptp.c:
enum i40e_ptp_gpio_pin_state {
end = -2,
invalid = -1,
off = 0,
in_A = 1,
in_B = 2,
out_A = 3,
out_B = 4,
};
This enum is included when CONFIG_I40E is enabled. As of commit
032676ff82 ("LoongArch: Update Loongson-3 default config file"),
CONFIG_I40E is set in the defconfig, which leads to the conflict.
Renaming the local variable avoids the redefinition and allows the
build to succeed.
Suggested-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Brahmajit Das <listout@listout.xyz>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20251017171551.53142-1-listout@listout.xyz
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We intend that EL0 exception handlers unmask all DAIF exceptions
before calling exit_to_user_mode().
When completing single-step of a suspended breakpoint, we do not call
local_daif_restore(DAIF_PROCCTX) before calling exit_to_user_mode(),
leaving all DAIF exceptions masked.
When pseudo-NMIs are not in use this is benign.
When pseudo-NMIs are in use, this is unsound. At this point interrupts
are masked by both DAIF.IF and PMR_EL1, and subsequent irq flag
manipulation may not work correctly. For example, a subsequent
local_irq_enable() within exit_to_user_mode_loop() will only unmask
interrupts via PMR_EL1 (leaving those masked via DAIF.IF), and
anything depending on interrupts being unmasked (e.g. delivery of
signals) will not work correctly.
This was detected by CONFIG_ARM64_DEBUG_PRIORITY_MASKING.
Move the call to `try_step_suspended_breakpoints()` outside of the check
so that interrupts can be unmasked even if we don't call the step handler.
Fixes: 0ac7584c08 ("arm64: debug: split single stepping exception entry")
Cc: <stable@vger.kernel.org> # 6.17
Signed-off-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: added Mark's rewritten commit log and some whitespace]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The GIC CDEOI system instruction requires the Rt field to be set to 0b11111
otherwise the instruction behaviour becomes CONSTRAINED UNPREDICTABLE.
Currenly, its usage is encoded as a system register write, with a constant
0 value:
write_sysreg_s(0, GICV5_OP_GIC_CDEOI)
While compiling with GCC, the 0 constant value, through these asm
constraints and modifiers ('x' modifier and 'Z' constraint combo):
asm volatile(__msr_s(r, "%x0") : : "rZ" (__val));
forces the compiler to issue the XZR register for the MSR operation (ie
that corresponds to Rt == 0b11111) issuing the right instruction encoding.
Unfortunately LLVM does not yet understand that modifier/constraint
combo so it ends up issuing a different register from XZR for the MSR
source, which in turns means that it encodes the GIC CDEOI instruction
wrongly and the instruction behaviour becomes CONSTRAINED UNPREDICTABLE
that we must prevent.
Add a conditional to write_sysreg_s() macro that detects whether it
is passed a constant 0 value and issues an MSR write with XZR as source
register - explicitly doing what the asm modifier/constraint is meant to
achieve through constraints/modifiers, fixing the LLVM compilation issue.
Fixes: 7ec80fb3f0 ("irqchip/gic-v5: Add GICv5 PPI support")
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Cc: Sascha Bischoff <sascha.bischoff@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 29d6d30f5c ("Btrfs: send, don't send rmdir for same target
multiple times") has fixed an issue that a send stream contained a rmdir
operation for the same directory multiple times. After that fix we keep
track of the last directory for which we sent a rmdir operation and
compare with it before sending a rmdir for the parent inode of a deleted
hardlink we are processing. But there is still a corner case that in
between rmdir dir operations for the same inode we find deleted hardlinks
for other parent inodes, so tracking just the last inode for which we sent
a rmdir operation is not enough.
Hardlinks of a file in the same directory are stored in the same INODE_REF
item, but if the number of hardlinks is too large and can not fit in a
leaf, we use INODE_EXTREF items to store them. The key of an INODE_EXTREF
item is (inode_id, INODE_EXTREF, hash[name, parent ino]), so between two
hardlinks for the same parent directory, we can find others for other
parent directories. For example for the reproducer below we get the
following (from a btrfs inspect-internal dump-tree output):
item 0 key (259 INODE_EXTREF 2309449) itemoff 16257 itemsize 26
index 6925 parent 257 namelen 8 name: foo.6923
item 1 key (259 INODE_EXTREF 2311350) itemoff 16231 itemsize 26
index 6588 parent 258 namelen 8 name: foo.6587
item 2 key (259 INODE_EXTREF 2457395) itemoff 16205 itemsize 26
index 6611 parent 257 namelen 8 name: foo.6609
(...)
So tracking the last directory's inode number does not work in this case
since we process a link for parent inode 257, then for 258 and then back
again for 257, and that second time we process a deleted link for 257 we
think we have not yet sent a rmdir operation.
Fix this by using a rbtree to keep track of all the directories for which
we have already sent rmdir operations, and add those directories to the
'check_dirs' ref list in process_recorded_refs() only if the directory is
not yet in the rbtree, otherwise skip it since it means we have already
sent a rmdir operation for that directory.
The following test script reproduces the problem:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
mkdir $MNT/a $MNT/b
echo 123 > $MNT/a/foo
for ((i = 1; i <= 1000; i++)); do
ln $MNT/a/foo $MNT/a/foo.$i
ln $MNT/a/foo $MNT/b/foo.$i
done
btrfs subvolume snapshot -r $MNT $MNT/snap1
btrfs send $MNT/snap1 -f /tmp/base.send
rm -r $MNT/a $MNT/b
btrfs subvolume snapshot -r $MNT $MNT/snap2
btrfs send -p $MNT/snap1 $MNT/snap2 -f /tmp/incremental.send
umount $MNT
mkfs.btrfs -f $DEV
mount $DEV $MNT
btrfs receive $MNT -f /tmp/base.send
btrfs receive $MNT -f /tmp/incremental.send
rm -f /tmp/base.send /tmp/incremental.send
umount $MNT
When running it, it fails like this:
$ ./test.sh
(...)
At subvol snap1
At snapshot snap2
ERROR: rmdir o257-9-0 failed: No such file or directory
CC: <stable@vger.kernel.org>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Ting-Chang Hou <tchou@synology.com>
[ Updated changelog ]
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull io_uring fixes from Jens Axboe:
- Revert of a change that went into an older kernel, and which has been
reported to cause a regression for some write workloads on LVM while
a snapshop is being created
- Fix a regression from this merge window, where some compilers (and/or
certain .config options) would cause an earlier evaluations of a
dereference which would then cause a NULL pointer dereference.
I was only able to reproduce this with OPTIMIZE_FOR_SIZE=y, but David
Howells hit it with just KASAN enabled. Depending on how things
inlined, this makes sense
- Fix for a missing lock around a mem region unregistration
- Fix for ring resizing with the same placement after resize
* tag 'io_uring-6.18-20251016' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/rw: check for NULL io_br_sel when putting a buffer
io_uring: fix unexpected placement on same size resizing
io_uring: protect mem region deregistration
Revert "io_uring/rw: drop -EOPNOTSUPP check in __io_complete_rw_common()"
Format the kernel-doc for SCALE_HW_CALIB_INVALID correctly to
avoid a kernel-doc warning:
Warning: include/linux/misc_cgroup.h:26 Enum value
'MISC_CG_RES_TDX' not described in enum 'misc_res_type'
Fixes: 7c035bea94 ("KVM: TDX: Register TDX host key IDs to cgroup misc controller")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- iostats accounting fixed on multipath retries (Amit)
- secure concatenation response fixup (Martin)
- tls partial record fixup (Wilfred)
- Fix for a lockdep reported issue with the elevator lock and
blk group frozen operations
- Fix for a regression in this merge window, where updating
'nr_requests' would not do the right thing for queues with
shared tags
* tag 'block-6.18-20251016' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
nvme/tcp: handle tls partially sent records in write_space()
block: Remove elevator_lock usage from blkg_conf frozen operations
blk-mq: fix stale tag depth for shared sched tags in blk_mq_update_nr_requests()
nvme-auth: update sc_c in host response
nvme-multipath: Skip nr_active increments in RETRY disposition
Pull mmc cleanup from Ulf Hansson:
"Move rpmb_frame struct and constants to rpmb common header
This helps us to avoid sharing an immutable branch between our git
trees. I was planning to send it before rc1, but I didn't make it"
* tag 'mmc-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
rpmb: move rpmb_frame struct and constants to common header
Pull sound fixes from Takashi Iwai:
"A collection of small fixes. All changes are rather boring
device-specific fixes and quirks:
- A few fixes for missing NULL checks
- ASoC NAU8821 fixes for jack and irq handling
- Various fixes for ASoC TAS2781, IDT821034, sc8280xp, max9809x,
wcd938x, and SoundWire
- Usual HD-audio and USB-audio quirks"
* tag 'sound-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda/realtek: Fix mute led for HP Omen 17-cb0xxx
ALSA: usb-audio: fix vendor quirk for Logitech H390
ALSA: usb-audio: add volume quirks for MS LifeChat LX-3000
ASoC: amd/sdw_utils: avoid NULL deref when devm_kasprintf() fails
ASoC: max98090/91: fixed max98091 ALSA widget powering up/down
ASoC: dt-bindings: Add compatible string fsl,imx-audio-tlv320
ASoC: codecs: wcd938x-sdw: remove redundant runtime pm calls
ASoC: sdw_utils: add rt1321 part id to codec_info_list
ALSA: usb-audio: Fix NULL pointer deference in try_to_register_card
ALSA: firewire: amdtp-stream: fix enum kernel-doc warnings
ALSA: usb-audio: add mixer_playback_min_mute quirk for Logitech H390
ASoC: nau8821: Avoid unnecessary blocking in IRQ handler
ASoC: nau8821: Add DMI quirk to bypass jack debounce circuit
ASoC: nau8821: Consistently clear interrupts before unmasking
ASoC: nau8821: Generalize helper to clear IRQ status
ASoC: nau8821: Cancel jdet_work before handling jack ejection
ASoC: codecs: Fix gain setting ranges for Renesas IDT821034 codec
ASoC: tas2781: Update ti,tas2781.yaml for adding tas58xx
ASoC: tas2781: Support more newly-released amplifiers tas58xx in the driver
ASoC: qcom: sc8280xp: Add support for QCS615
...
Pull drm fixes from Dave Airlie:
"As per usual xe/amdgpu are the leaders, with some i915 and then a
bunch of scattered fixes. There are a bunch of stability fixes for
some older amdgpu cards.
draw:
- Avoid color truncation
gpuvm:
- Avoid kernel-doc warning
sched:
- Avoid double free
i915:
- Skip GuC communication warning if reset is in progress
- Couple frontbuffer related fixes
- Deactivate PSR only on LNL and when selective fetch enabled
xe:
- Increase global invalidation timeout to handle some workloads
- Fix NPD while evicting BOs in an array of VM binds
- Fix resizable BAR to account for possibly needing to move BARs
other than the LMEMBAR
- Fix error handling in xe_migrate_init()
- Fix atomic fault handling with mixed mappings or if the page is
already in VRAM
- Enable media samplers power gating for platforms before Xe2
- Fix de-registering exec queue from GuC when unbinding
- Ensure data migration to system if indicated by madvise with SVM
- Fix kerneldoc for kunit change
- Always account for cacheline alignment on migration
- Drop bogus assertion on eviction
amdgpu:
- Backlight fix
- SI fixes
- CIK fix
- Make CE support debug only
- IP discovery fix
- Ring reset fixes
- GPUVM fault memory barrier fix
- Drop unused structures in amdgpu_drm.h
- JPEG debugfs fix
- VRAM handling fixes for GPUs without VRAM
- GC 12 MES fixes
amdkfd:
- MES fix
ast:
- Fix display output after reboot
bridge:
- lt9211: Fix version check
panthor:
- Fix MCU suspend
qaic:
- Init bootlog in correct order
- Treat remaining == 0 as error in find_and_map_user_pages()
- Lock access to DBC request queue
rockchip:
- vop2: Fix destination size in atomic check"
* tag 'drm-fixes-2025-10-17' of https://gitlab.freedesktop.org/drm/kernel: (44 commits)
drm/sched: Fix potential double free in drm_sched_job_add_resv_dependencies
drm/xe/evict: drop bogus assert
drm/xe/migrate: don't misalign current bytes
drm/xe/kunit: Fix kerneldoc for parameterized tests
drm/xe/svm: Ensure data will be migrated to system if indicated by madvise.
drm/gpuvm: Fix kernel-doc warning for drm_gpuvm_map_req.map
drm/i915/psr: Deactivate PSR only on LNL and when selective fetch enabled
drm/ast: Blank with VGACR17 sync enable, always clear VGACRB6 sync off
accel/qaic: Synchronize access to DBC request queue head & tail pointer
accel/qaic: Treat remaining == 0 as error in find_and_map_user_pages()
accel/qaic: Fix bootlog initialization ordering
drm/rockchip: vop2: use correct destination rectangle height check
drm/draw: fix color truncation in drm_draw_fill24
drm/xe/guc: Check GuC running state before deregistering exec queue
drm/xe: Enable media sampler power gating
drm/xe: Handle mixed mappings and existing VRAM on atomic faults
drm/xe/migrate: Fix an error path
drm/xe: Move rebar to be done earlier
drm/xe: Don't allow evicting of BOs in same VM in array of VM binds
drm/xe: Increase global invalidation timeout to 1000us
...
Pull i2c fixes from Wolfram Sang:
- PM cleanup after all prerequisites are merged with rc1
- usbio: missing addition after all dependencies are in
- slimpro: DT binding schema conversion
* tag 'i2c-for-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: Convert apm,xgene-slimpro-i2c to DT schema
i2c: usbio: Add ACPI device-id for MTL-CVF devices
i2c: Remove redundant pm_runtime_mark_last_busy() calls
TEE QTEE fixes for v6.18
- Adds ARCH_QCOM dependency for the QTEE driver
- Fixing return values for copy_from_user() failures
- Guarding against potential off by one read
* tag 'tee-qcomtee-fixes-for-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jenswi/linux-tee:
tee: QCOMTEE should depend on ARCH_QCOM
tee: qcom: return -EFAULT instead of -EINVAL if copy_from_user() fails
tee: qcom: prevent potential off by one read
Due to the wider deployment of the ->sync_state() support, for PM domains
for example, we are receiving reports about the sync_state() pending
message that is being logged in fw_devlink_dev_sync_state(). In particular
as it's printed at the warning level, which is questionable.
Even if it certainly is useful to know that the ->sync_state() condition
could not be met, there may be nothing wrong with it. For example, a driver
may be built as module and are still waiting to be initialized/probed. For
this reason let's move to the info level for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Sebin Francis <sebin.francis@ti.com>
Reported-by: Diederik de Haas <didi.debian@cknow.org>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Sebin Francis <sebin.francis@ti.com>
Tested-by: Sebin Francis <sebin.francis@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert recently reported two corrupted images that can cause system
crashes, which are related to the new encoded extents introduced
in Linux 6.15:
- The first one [1] has plen != 0 (e.g. plen == 0x2000000) but
(plen & Z_EROFS_EXTENT_PLEN_MASK) == 0. It is used to represent
special extents such as sparse extents (!EROFS_MAP_MAPPED), but
previously only plen == 0 was handled;
- The second one [2] has pa 0xffffffffffdcffed and plen 0xb4000,
then "cur [0xfffffffffffff000] += bvec.bv_len [0x1000]" in
"} while ((cur += bvec.bv_len) < end);" wraps around, causing an
out-of-bound access of pcl->compressed_bvecs[] in
z_erofs_submit_queue(). EROFS only supports 48-bit physical block
addresses (up to 1EiB for 4k blocks), so add a sanity check to
enforce this.
Fixes: 1d191b4ca5 ("erofs: implement encoded extent metadata")
Reported-by: Robert Morris <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/r/75022.1759355830@localhost [1]
Closes: https://lore.kernel.org/r/80524.1760131149@localhost [2]
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
On all platforms set_clock_selection() writes to a GRF register. This
requires certain clocks running and thus should happen before the
clocks are disabled.
This has been noticed on RK3576 Sige5, which hangs during system suspend
when trying to suspend the second network interface. Note, that
suspending the first interface works, because the second device ensures
that the necessary clocks for the GRF are enabled.
Cc: stable@vger.kernel.org
Fixes: 2f2b60a0ec ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251014-rockchip-network-clock-fix-v1-1-c257b4afdf75@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Driver Changes:
- Increase global invalidation timeout to handle some workloads
(Kenneth Graunke)
- Fix NPD while evicting BOs in an array of VM binds (Matthew Brost)
- Fix resizable BAR to account for possibly needing to move BARs other
than the LMEMBAR (Lucas De Marchi)
- Fix error handling in xe_migrate_init() (Thomas Hellström)
- Fix atomic fault handling with mixed mappings or if the page is
already in VRAM (Matthew Brost)
- Enable media samplers power gating for platforms before Xe2 (Vinay
Belgaumkar)
- Fix de-registering exec queue from GuC when unbinding (Matthew Brost)
- Ensure data migration to system if indicated by madvise with SVM
(Thomas Hellström)
- Fix kerneldoc for kunit change (Matt Roper)
- Always account for cacheline alignment on migration (Matthew Auld)
- Drop bogus assertion on eviction (Matthew Auld)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/rch735eqkmprfyutk3ux2fsqa3e5ve4p77w7a5j66qdpgyquxr@ao3wzcqtpn6s
Creating FDB entries is possible from a non-initial user namespace when
having CAP_NET_ADMIN, yet, when deleting FDB entries, processes receive
an EPERM because the capability is always checked against the initial
user namespace. This restricts the FDB management from unprivileged
containers.
Drop the netlink_capable check in rtnl_fdb_del as it was originally
dropped in c5c351088a and reintroduced in 1690be63a2 without
intention.
This patch was tested using a container on GyroidOS, where it was
possible to delete FDB entries from an unprivileged user namespace and
private network namespace.
Fixes: 1690be63a2 ("bridge: Add vlan support to static neighbors")
Reviewed-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Tested-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Johannes Wiesböck <johannes.wiesboeck@aisec.fraunhofer.de>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20251015201548.319871-1-johannes.wiesboeck@aisec.fraunhofer.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Apply the formatting guidelines introduced in the previous commit to
make the file `rustfmt`-clean again.
Reviewed-by: Benno Lossin <lossin@kernel.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
`rustfmt`, by default, formats imports in a way that is prone to conflicts
while merging and rebasing, since in some cases it condenses several
items into the same line.
For instance, Linus mentioned [1] that the following case:
use crate::{
fmt,
page::AsPageIter,
};
is compressed by `rustfmt` into:
use crate::{fmt, page::AsPageIter};
which is undesirable.
Similarly, `rustfmt` may put several items in the same line even if the
braces span already multiple lines, e.g.:
use kernel::{
acpi, c_str,
device::{property, Core},
of, platform,
};
The options that control the formatting behavior around imports are
generally unstable, and `rustfmt` releases do not allow to use nightly
features, unlike the compiler and other Rust tooling [2].
For the moment, we can introduce a workaround to prevent `rustfmt`
from compressing the example above -- the "trailing empty comment":
use crate::{
fmt,
page::AsPageIter, //
};
which is reminiscent of the trailing comma behavior in other formatters.
We already used empty comments for formatting purposes in the past,
e.g. in commit b9b701fce4 ("rust: clarify the language unstable features
in use").
In addition, `rustfmt` actually reformats with a vertical layout (i.e. it
does not put two items in the same line) when seeing such a comment,
i.e. it doesn't just preserve the formatting, which is good in the sense
that we can use it to easily reformat some imports, since it matches
the style we generally want to have.
A Git merge driver would help (suggested by Gary and Wedson), though
maintainers would need to set it up, the diffs would still be larger
and the formatting rules for imports would remain hard to predict.
Thus document the style that we will follow in the coding guidelines
by introducing a new section and explain how the trailing empty comment
works there too.
We discussed the issue with upstream Rust in our usual Rust <-> Rust
for Linux meeting [3], and there have also been a few other discussions
in parallel in issues [4][5] and Zulip [6]. We will see what happens,
but upstream Rust has already created a subteam of `rustfmt` to try
to overcome the bandwidth issue [7], which is a good signal, and some
organization work has already started (e.g. tracking issues). We will
continue our discussions with them about it.
Cc: Caleb Cartwright <caleb.cartwright@outlook.com>
Cc: Yacin Tmimi <yacintmimi@gmail.com>
Cc: Manish Goregaokar <manishsmail@gmail.com>
Cc: Deadbeef <ent3rm4n@gmail.com>
Cc: Cameron Steffen <cam.steffen94@gmail.com>
Cc: Jieyou Xu <jieyouxu@outlook.com>
Link: https://lore.kernel.org/all/CAHk-=wgO7S_FZUSBbngG5vtejWOpzDfTTBkVvP3_yjJmFddbzA@mail.gmail.com/ [1]
Link: https://github.com/rust-lang/rustfmt/issues/4884 [2]
Link: https://hackmd.io/iSCyY3JTTz-g8YM-nnzTTA [3]
Link: https://github.com/rust-lang/rustfmt/issues/4991 [4]
Link: https://github.com/rust-lang/rustfmt/issues/3361 [5]
Link: https://rust-lang.zulipchat.com/#narrow/channel/392734-council/topic/rustfmt.20maintenance/near/543815381 [6]
Link: https://github.com/rust-lang/team/pull/2017 [7]
Reviewed-by: Benno Lossin <lossin@kernel.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
The 'accel' parameter of mlx5e_txwqe_build_eseg_csum() and the similar
'state' parameter of mlx5e_accel_tx_ids_len() were NULL when called
from mlx5i_sq_xmit() and were causing kernel panics from that context.
Fix that by passing in a local empty mlx5e_accel_tx_state variable, thus
guaranteeing that 'accel' is never NULL. Also remove an unnecessary
check from mlx5e_tx_wqe_inline_mode().
Fixes: e5a1861a29 ("net/mlx5e: Implement PSP Tx data path")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1760511923-890650-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some network drivers assume this field is zero after napi_get_frags().
We must clear it in napi_reuse_skb() otherwise the following can happen:
1) A packet is received, and skb_shinfo(skb)->hwtstamps is populated
because a bit in the receive descriptor announced hwtstamp
availability for this packet.
2) Packet is given to gro layer via napi_gro_frags().
3) Packet is merged to a prior one held in GRO queues.
4) skb is saved after some cleanup in napi->skb via a call
to napi_reuse_skb().
5) Next packet is received 10 seconds later, gets the recycled skb
from napi_get_frags().
6) The receive descriptor does not announce hwtstamp availability.
Driver does not clear shinfo->hwtstamps.
7) We have in shinfo->hwtstamps an old timestamp.
Fixes: ac45f602ee ("net: infrastructure for hardware time stamping")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20251015063221.4171986-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with Clang 20 or newer, there are some objtool warnings
from unexpected fallthroughs to other functions:
vmlinux.o: warning: objtool: mlx5e_mpwrq_mtts_per_wqe() falls through to next function mlx5e_mpwrq_max_num_entries()
vmlinux.o: warning: objtool: mlx5e_mpwrq_max_log_rq_size() falls through to next function mlx5e_get_linear_rq_headroom()
LLVM 20 contains an (admittedly problematic [1]) optimization [2] to
convert divide by zero into the equivalent of __builtin_unreachable(),
which invokes undefined behavior and destroys code generation when it is
encountered in a control flow graph.
mlx5e_mpwrq_umr_entry_size() returns 0 in the default case of an
unrecognized mlx5e_mpwrq_umr_mode value. mlx5e_mpwrq_mtts_per_wqe(),
which is inlined into mlx5e_mpwrq_max_log_rq_size(), uses the result of
mlx5e_mpwrq_umr_entry_size() in a divide operation without checking for
zero, so LLVM is able to infer there will be a divide by zero in this
case and invokes undefined behavior. While there is some proposed work
to isolate this undefined behavior and avoid the destructive code
generation that results in these objtool warnings, code should still be
defensive against divide by zero.
As the WARN_ONCE() implies that an invalid value should be handled
gracefully, return 1 instead of 0 in the default case so that the
results of this division operation is always valid.
Fixes: 168723c1f8 ("net/mlx5e: xsk: Use umr_mode to calculate striding RQ parameters")
Link: https://lore.kernel.org/CAGG=3QUk8-Ak7YKnRziO4=0z=1C_7+4jF+6ZeDQ9yF+kuTOHOQ@mail.gmail.com/ [1]
Link: 37932643ab [2]
Closes: https://github.com/ClangBuiltLinux/linux/issues/2131
Closes: https://github.com/ClangBuiltLinux/linux/issues/2132
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251014-mlx5e-avoid-zero-div-from-mlx5e_mpwrq_umr_entry_size-v1-1-dc186b8819ef@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TX frames aren't padded and unknown memory is sent into the ether.
Theoretically, it isn't even guaranteed that the extra memory exists
and can be sent out, which could cause further problems. In practice,
I found that plenty of tailroom exists in the skb itself (in my test
with ping at least) and skb_padto() easily succeeds, so use it here.
In the event of -ENOMEM drop the frame like other drivers do.
The use of one more padding byte instead of a USB zero-length packet
is retained to avoid regression. I have a dodgy Etron xHCI controller
which doesn't seem to support sending ZLPs at all.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251014203528.3f9783c4.michal.pecio@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
amd-drm-fixes-6.18-2025-10-16:
amdgpu:
- Backlight fix
- SI fixes
- CIK fix
- Make CE support debug only
- IP discovery fix
- Ring reset fixes
- GPUVM fault memory barrier fix
- Drop unused structures in amdgpu_drm.h
- JPEG debugfs fix
- VRAM handling fixes for GPUs without VRAM
- GC 12 MES fixes
amdkfd:
- MES fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20251016132224.2534946-1-alexander.deucher@amd.com
With TLS enabled, records that are encrypted and appended to TLS TX
list can fail to see a retry if the underlying TCP socket is busy, for
example, hitting an EAGAIN from tcp_sendmsg_locked(). This is not known
to the NVMe TCP driver, as the TLS layer successfully generated a record.
Typically, the TLS write_space() callback would ensure such records are
retried, but in the NVMe TCP Host driver, write_space() invokes
nvme_tcp_write_space(). This causes a partially sent record in the TLS TX
list to timeout after not being retried.
This patch fixes the above by calling queue->write_space(), which calls
into the TLS layer to retry any pending records.
Fixes: be8e82caa6 ("nvme-tcp: enable TLS handshake upcall")
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
ASoC: Fixes for v6.18
A moderately large collection of driver specific fixes, plus a few new
quirks and device IDs. The NAU8821 changes are a little large but more
in mechanical ways than in ways that are complex.
When __lookup_instance() allocates a func_instance structure but fails
to allocate the must_write_set array, it returns an error without freeing
the previously allocated func_instance. This causes a memory leak of 192
bytes (sizeof(struct func_instance)) each time this error path is triggered.
Fix by freeing 'result' on must_write_set allocation failure.
Fixes: b3698c356a ("bpf: callchain sensitive stack liveness tracking using CFG")
Reported-by: BPF Runtime Fuzzer (BRF)
Signed-off-by: Shardul Bankar <shardulsb08@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://patch.msgid.link/20251016063330.4107547-1-shardulsb08@gmail.com
Pull btrfs fixes from David Sterba:
- in tree-checker fix extref bounds check
- reorder send context structure to avoid
-Wflex-array-member-not-at-end warning
- fix extent readahead length for compressed extents
- fix memory leaks on error paths (qgroup assign ioctl, zone loading
with raid stripe tree enabled)
- fix how device specific mount options are applied, in particular the
'ssd' option will be set unexpectedly
- fix tracking of relocation state when tasks are running and
cancellation is attempted
- adjust assertion condition for folios allocated for scrub
- remove incorrect assertion checking for block group when populating
free space tree
* tag 'for-6.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: send: fix -Wflex-array-member-not-at-end warning in struct send_ctx
btrfs: tree-checker: fix bounds check in check_inode_extref()
btrfs: fix memory leaks when rejecting a non SINGLE data profile without an RST
btrfs: fix incorrect readahead expansion length
btrfs: do not assert we found block group item when creating free space tree
btrfs: do not use folio_test_partial_kmap() in ASSERT()s
btrfs: only set the device specific options after devices are opened
btrfs: fix memory leak on duplicated memory in the qgroup assign ioctl
btrfs: fix clearing of BTRFS_FS_RELOC_RUNNING if relocation already running
Pull smb server fixes from Steve French:
- Fix RPC hang due to locking bug
- Fix for memory leak in read and refcount leak (in session setup)
- Minor cleanup
* tag 'v6.18-rc1-smb-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix recursive locking in RPC handle list access
smb/server: fix possible refcount leak in smb2_sess_setup()
smb/server: fix possible memory leak in smb2_read()
smb: server: Use common error handling code in smb_direct_rdma_xmit()
Pull networking fixes from Paolo Abeni:
"Including fixes from CAN
Current release - regressions:
- udp: do not use skb_release_head_state() before
skb_attempt_defer_free()
- gro_cells: use nested-BH locking for gro_cell
- dpll: zl3073x: increase maximum size of flash utility
Previous releases - regressions:
- core: fix lockdep splat on device unregister
- tcp: fix tcp_tso_should_defer() vs large RTT
- tls:
- don't rely on tx_work during send()
- wait for pending async decryptions if tls_strp_msg_hold fails
- can: j1939: add missing calls in NETDEV_UNREGISTER notification
handler
- eth: lan78xx: fix lost EEPROM write timeout in
lan78xx_write_raw_eeprom
Previous releases - always broken:
- ip6_tunnel: prevent perpetual tunnel growth
- dpll: zl3073x: handle missing or corrupted flash configuration
- can: m_can: fix pm_runtime and CAN state handling
- eth:
- ixgbe: fix too early devlink_free() in ixgbe_remove()
- ixgbevf: fix mailbox API compatibility
- gve: Check valid ts bit on RX descriptor before hw timestamping
- idpf: cleanup remaining SKBs in PTP flows
- r8169: fix packet truncation after S4 resume on RTL8168H/RTL8111H"
* tag 'net-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
udp: do not use skb_release_head_state() before skb_attempt_defer_free()
net: usb: lan78xx: fix use of improperly initialized dev->chipid in lan78xx_reset
netdevsim: set the carrier when the device goes up
selftests: tls: add test for short splice due to full skmsg
selftests: net: tls: add tests for cmsg vs MSG_MORE
tls: don't rely on tx_work during send()
tls: wait for pending async decryptions if tls_strp_msg_hold fails
tls: always set record_type in tls_process_cmsg
tls: wait for async encrypt in case of error during latter iterations of sendmsg
tls: trim encrypted message to match the plaintext on short splice
tg3: prevent use of uninitialized remote_adv and local_adv variables
MAINTAINERS: new entry for IPv6 IOAM
gve: Check valid ts bit on RX descriptor before hw timestamping
net: core: fix lockdep splat on device unregister
MAINTAINERS: add myself as maintainer for b53
selftests: net: check jq command is supported
net: airoha: Take into account out-of-order tx completions in airoha_dev_xmit()
tcp: fix tcp_tso_should_defer() vs large RTT
r8152: add error handling in rtl8152_driver_init
usbnet: Fix using smp_processor_id() in preemptible code warnings
...
Pull ata fix from Niklas Cassel:
- Do not print an error message (and assume that the General Purpose
Log Directory log page is not supported) for a device that reports a
bogus General Purpose Logging Version.
Unsurprisingly, many vendors fail to report the only valid General
Purpose Logging Version (Damien)
* tag 'ata-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-core: relax checks in ata_read_log_directory()
test_parse_test_list_file writes some data to
/tmp/bpf_arg_parsing_test.XXXXXX and parse_test_list_file() will read
the data back. However, after writing data to that file, we forget to
call fsync() and it's causing testing failure in my laptop. This patch
helps fix it by adding the missing fsync() call.
Fixes: 64276f01dc ("selftests/bpf: Test_progs can read test lists from file")
Signed-off-by: Xing Guo <higuoxing@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20251016035330.3217145-1-higuoxing@gmail.com
The Logitech G502 Hero Wireless's high resolution scrolling resets after
being unplugged without notifying the driver, causing extremely slow
scrolling.
The only indication of this is a battery update packet, so add a quirk to
detect when the device is unplugged and re-enable the scrolling.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218037
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In dw_hdmi_rk3228_setup_hpd(), the SCLIN mask incorrectly references
the RK3328 variant. This change updates it to the RK3228-specific mask
RK3228_HDMI_SCLIN_MSK using FIELD_PREP_WM16, ensuring proper HPD and
I2C pin configuration for RK3228.
Change: RK3328_HDMI_SCLIN_MSK -> RK3228_HDMI_SCLIN_MSK
Fixes: 63df37f3fc ("drm/rockchip: dw_hdmi: switch to FIELD_PREP_WM16* macros")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20251010173143.72733-1-alok.a.tiwari@oracle.com
Attaching UBI on the flash with more than one plane per lun will lead to
the following error:
[ 2.980989] spi-nand spi0.0: Micron SPI NAND was found.
[ 2.986309] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 2.994978] 2 fixed-partitions partitions found on MTD device spi0.0
[ 3.001350] Creating 2 MTD partitions on "spi0.0":
[ 3.006159] 0x000000000000-0x000000020000 : "bl2"
[ 3.011663] 0x000000020000-0x000010000000 : "ubi"
...
[ 6.391748] ubi0: attaching mtd1
[ 6.412545] ubi0 error: ubi_attach: PEB 0 contains corrupted VID header, and the data does not contain all 0xFF
[ 6.422677] ubi0 error: ubi_attach: this may be a non-UBI PEB or a severe VID header corruption which requires manual inspection
[ 6.434249] Volume identifier header dump:
[ 6.438349] magic 55424923
[ 6.441482] version 1
[ 6.444007] vol_type 0
[ 6.446539] copy_flag 0
[ 6.449068] compat 0
[ 6.451594] vol_id 0
[ 6.454120] lnum 1
[ 6.456651] data_size 4096
[ 6.459442] used_ebs 1061644134
[ 6.462748] data_pad 0
[ 6.465274] sqnum 0
[ 6.467805] hdr_crc 61169820
[ 6.470943] Volume identifier header hexdump:
[ 6.475308] hexdump of PEB 0 offset 4096, length 126976
[ 6.507391] ubi0 warning: ubi_attach: valid VID header but corrupted EC header at PEB 4
[ 6.515415] ubi0 error: ubi_compare_lebs: unsupported on-flash UBI format
[ 6.522222] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[ 6.529294] UBI error: cannot attach mtd1
Non dirmap reading works good. Looking to spi_mem_no_dirmap_read() code we'll see:
static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc *desc,
u64 offs, size_t len, void *buf)
{
struct spi_mem_op op = desc->info.op_tmpl;
int ret;
// --- see here ---
op.addr.val = desc->info.offset + offs;
//-----------------
op.data.buf.in = buf;
op.data.nbytes = len;
ret = spi_mem_adjust_op_size(desc->mem, &op);
if (ret)
return ret;
ret = spi_mem_exec_op(desc->mem, &op);
if (ret)
return ret;
return op.data.nbytes;
}
The similar happens for spi_mem_no_dirmap_write(). Thus the address
passed to the flash should take in the account the value of
desc->info.offset.
This patch fix dirmap reading/writing of flashes with more than one
plane per lun.
Fixes: a403997c12 ("spi: airoha: add SPI-NAND Flash controller driver")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251012121707.2296160-7-mikhail.kshevetskiy@iopsys.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Booting without this patch and disabled dirmap support results in
[ 2.980719] spi-nand spi0.0: Micron SPI NAND was found.
[ 2.986040] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 2.994709] 2 fixed-partitions partitions found on MTD device spi0.0
[ 3.001075] Creating 2 MTD partitions on "spi0.0":
[ 3.005862] 0x000000000000-0x000000020000 : "bl2"
[ 3.011272] 0x000000020000-0x000010000000 : "ubi"
...
[ 6.195594] ubi0: attaching mtd1
[ 13.338398] ubi0: scanning is finished
[ 13.342188] ubi0 error: ubi_read_volume_table: the layout volume was not found
[ 13.349784] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[ 13.356897] UBI error: cannot attach mtd1
If dirmap is disabled or not supported in the spi driver, the dirmap requests
will be executed via exec_op() handler. Thus, if the hardware supports
dual/quad spi modes, then corresponding requests will be sent to exec_op()
handler. Current driver does not support such requests, so error is arrised.
As result the flash can't be read/write.
This patch adds support of dual and quad wires spi modes to exec_op() handler.
Fixes: a403997c12 ("spi: airoha: add SPI-NAND Flash controller driver")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251012121707.2296160-4-mikhail.kshevetskiy@iopsys.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
If obj_exts allocation failed, slab->obj_exts is set to OBJEXTS_ALLOC_FAIL,
But we do not clear it when freeing the slab. Since OBJEXTS_ALLOC_FAIL and
MEMCG_DATA_OBJEXTS currently share the same bit position, during the
release of the associated folio, a VM_BUG_ON_FOLIO() check in
folio_memcg_kmem() is triggered because the OBJEXTS_ALLOC_FAIL flag was
not cleared, causing it to be interpreted as a kmem folio (non-slab)
with MEMCG_OBJEXTS_DATA flag set, which is invalid because
MEMCG_OBJEXTS_DATA is supposed to be set only on slabs.
Another problem that predates sharing the OBJEXTS_ALLOC_FAIL and
MEMCG_DATA_OBJEXTS bits is that on configurations with
is_check_pages_enabled(), the non-cleared bit in page->memcg_data will
trigger a free_page_is_bad() failure "page still charged to cgroup"
When freeing a slab, we clear slab->obj_exts if the obj_ext array has
been successfully allocated. So let's clear it also when the allocation
has failed.
Fixes: 09c46563ff ("codetag: debug: introduce OBJEXTS_ALLOC_FAIL to mark failed slab_ext allocations")
Fixes: 7612833192 ("slab: Reuse first bit for OBJEXTS_ALLOC_FAIL")
Link: https://lore.kernel.org/all/20251015141642.700170-1-hao.ge@linux.dev/
Cc: <stable@vger.kernel.org>
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
When adding dependencies with drm_sched_job_add_dependency(), that
function consumes the fence reference both on success and failure, so in
the latter case the dma_fence_put() on the error path (xarray failed to
expand) is a double free.
Interestingly this bug appears to have been present ever since
commit ebd5f74255 ("drm/sched: Add dependency tracking"), since the code
back then looked like this:
drm_sched_job_add_implicit_dependencies():
...
for (i = 0; i < fence_count; i++) {
ret = drm_sched_job_add_dependency(job, fences[i]);
if (ret)
break;
}
for (; i < fence_count; i++)
dma_fence_put(fences[i]);
Which means for the failing 'i' the dma_fence_put was already a double
free. Possibly there were no users at that time, or the test cases were
insufficient to hit it.
The bug was then only noticed and fixed after
commit 9c2ba26535 ("drm/scheduler: use new iterator in drm_sched_job_add_implicit_dependencies v2")
landed, with its fixup of
commit 4eaf02d607 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies").
At that point it was a slightly different flavour of a double free, which
commit 963d0b3569 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies harder")
noticed and attempted to fix.
But it only moved the double free from happening inside the
drm_sched_job_add_dependency(), when releasing the reference not yet
obtained, to the caller, when releasing the reference already released by
the former in the failure case.
As such it is not easy to identify the right target for the fixes tag so
lets keep it simple and just continue the chain.
While fixing we also improve the comment and explain the reason for taking
the reference and not dropping it.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Fixes: 963d0b3569 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies harder")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/dri-devel/aNFbXq8OeYl3QSdm@stanley.mountain/
Cc: Christian König <christian.koenig@amd.com>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Danilo Krummrich <dakr@kernel.org>
Cc: Philipp Stanner <phasta@kernel.org>
Cc: Christian König <ckoenig.leichtzumerken@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org # v5.16+
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20251015084015.6273-1-tvrtko.ursulin@igalia.com
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series addresses a set of issues in the Nuvoton NAU88L21
audio codec driver related to interrupt handling and jack hotplug
detection reliability.
The changes focus on:
* Eliminating race conditions between jack insertion and ejection events
* Ensuring interrupts are consistently and correctly cleared before
unmasking
* Introducing a DMI-based quirk to bypass the jack debounce circuit on
Valve Steam Deck, improving detection accuracy under stress
* Improving robustness of the IRQ handler by avoiding unnecessary
blocking operations
The series has been tested on affected hardware to verify correct
behavior during repeated and rapid jack hotplug cycles.
Merge series from Le Qi <le.qi@oss.qualcomm.com>:
This patch series adds support for the QCS615 sound card:
- Updates device tree bindings for SM8250 to include QCS615.
- Adds QCS615 support in the SC8280XP ASoC driver.
Vendor quirk QUIRK_FLAG_CTL_MSG_DELAY_1M was inadvertently missing when
adding quirk for Logitech H390. Add it back.
Fixes: 2b929b6eec ("ALSA: usb-audio: add mixer_playback_min_mute quirk for Logitech H390")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ID 045e:070f Microsoft Corp. LifeChat LX-3000 Headset
has muted minimum Speaker Playback Volume, and 4 amixer steps were
observed to produce 1 actual volume step.
Apply min_mute quirk and correct res=48 -> 4*48.
Tested with the device.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kunit's generate_params() was recently updated to take an additional
test context parameter. Xe's IP and platform parameter generators were
updated accordingly at the same time, but the new parameter was not
added to the functions' kerneldoc, resulting in the following warnings:
Warning: drivers/gpu/drm/xe/tests/xe_pci.c:78 function parameter 'test' not described in 'xe_pci_fake_data_gen_params'
Warning: drivers/gpu/drm/xe/tests/xe_pci.c:254 function parameter 'test' not described in 'xe_pci_graphics_ip_gen_param'
Warning: drivers/gpu/drm/xe/tests/xe_pci.c:278 function parameter 'test' not described in 'xe_pci_media_ip_gen_param'
Warning: drivers/gpu/drm/xe/tests/xe_pci.c:302 function parameter 'test' not described in 'xe_pci_id_gen_param'
Warning: drivers/gpu/drm/xe/tests/xe_pci.c:390 function parameter 'test' not described in 'xe_pci_live_device_gen_param'
5 warnings as errors
Document the new parameter to eliminate the warnings and make CI happy.
Fixes: b9a214b5f6 ("kunit: Pass parameterized test context to generate_params()")
Reviewed-by: Shuicheng Lin <shuicheng.lin@intel.com>
Link: https://lore.kernel.org/r/20251013153014.2362879-2-matthew.d.roper@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 89e347f8a7)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
If the location madvise() is set to
DRM_XE_PREFERRED_LOC_DEFAULT_SYSTEM, the drm_pagemap in the
SVM gpu fault handler will be set to NULL. However there is nothing
that explicitly migrates the data to system if it is already present
in device memory.
In that case, set the device memory owner to NULL to ensure
data gets properly migrated to system on page-fault.
v2:
- Remove redundant dpagemap assignment (Himal Prasad Ghimiray)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com> #v1
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://lore.kernel.org/r/20251010104149.72783-2-thomas.hellstrom@linux.intel.com
Fixes: 10aa5c8060 ("drm/gpusvm, drm/xe: Fix userptr to not allow device private pages")
(cherry picked from commit 2cfcea7a74)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Now that smb3_crypto_shash_allocate() and smb311_crypto_shash_allocate()
are identical and only allocate "cmac(aes)", delete the latter and
replace the call to it with the former.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Now that the SMB client accesses MD5, HMAC-MD5, HMAC-SHA256, and SHA-512
only via the library API and not via crypto_shash, allocating
crypto_shash objects for these algorithms is no longer necessary.
Remove all these allocations, their corresponding kconfig selections,
and their corresponding module soft dependencies.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
For the HMAC-MD5 computations in NTLMv2, use the HMAC-MD5 library
instead of a "hmac(md5)" crypto_shash. This is simpler and faster.
With the library there's no need to allocate memory, no need to handle
errors, and the HMAC-MD5 code is accessed directly without inefficient
indirect calls and other unnecessary API overhead.
To preserve the existing behavior of NTLMv2 support being disabled when
the kernel is booted with "fips=1", make setup_ntlmv2_rsp() check
fips_enabled itself. Previously it relied on the error from
cifs_alloc_hash("hmac(md5)", &hmacmd5).
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Convert cifs_calc_signature() to use the MD5 library instead of a "md5"
crypto_shash. This is simpler and faster. With the library there's no
need to allocate memory, no need to handle errors, and the MD5 code is
accessed directly without inefficient indirect calls and other
unnecessary API overhead.
To preserve the existing behavior of MD5 signature support being
disabled when the kernel is booted with "fips=1", make
cifs_calc_signature() check fips_enabled itself. Previously it relied
on the error from cifs_alloc_hash("md5", &server->secmech.md5).
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Convert parse_mf_symlink() and format_mf_symlink() to use the MD5
library instead of a "md5" crypto_shash. This is simpler and faster.
With the library there's no need to allocate memory, no need to handle
errors, and the MD5 code is accessed directly without inefficient
indirect calls and other unnecessary API overhead.
This also fixes an issue where these functions did not work on kernels
booted in FIPS mode. The use of MD5 here is for data integrity rather
than a security purpose, so it can use a non-FIPS-approved algorithm.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Convert smb2_calc_signature() to use the HMAC-SHA256 library instead of
a "hmac(sha256)" crypto_shash. This is simpler and faster. With the
library there's no need to allocate memory, no need to handle errors,
and the HMAC-SHA256 code is accessed directly without inefficient
indirect calls and other unnecessary API overhead.
To make this possible, make __cifs_calc_signature() support both the
HMAC-SHA256 library and crypto_shash. (crypto_shash is still needed for
HMAC-MD5 and AES-CMAC. A later commit will switch HMAC-MD5 from shash
to the library. I'd like to eventually do the same for AES-CMAC, but it
doesn't have a library API yet. So for now, shash is still needed.)
Also remove the unnecessary 'sigptr' variable.
For now smb3_crypto_shash_allocate() still allocates a "hmac(sha256)"
crypto_shash. It will be removed in a later commit.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Convert generate_key() to use the HMAC-SHA256 library instead of a
"hmac(sha256)" crypto_shash. This is simpler and faster. With the
library there's no need to allocate memory, no need to handle errors,
and the HMAC-SHA256 code is accessed directly without inefficient
indirect calls and other unnecessary API overhead.
Also remove the unnecessary 'hashptr' variable.
For now smb3_crypto_shash_allocate() still allocates a "hmac(sha256)"
crypto_shash. It will be removed in a later commit.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Convert smb311_update_preauth_hash() to use the SHA-512 library instead
of a "sha512" crypto_shash. This is simpler and faster. With the
library there's no need to allocate memory, no need to handle errors,
and the SHA-512 code is accessed directly without inefficient indirect
calls and other unnecessary API overhead.
Remove the call to smb311_crypto_shash_allocate() from
smb311_update_preauth_hash(), since it appears to have been needed only
to allocate the "sha512" crypto_shash. (It also had the side effect of
allocating the "cmac(aes)" crypto_shash, but that's also done in
generate_key() which is where the AES-CMAC key is initialized.)
For now the "sha512" crypto_shash is still being allocated elsewhere.
It will be removed in a later commit.
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Malicious SMB server can send invalid reply to FSCTL_DFS_GET_REFERRALS
- reply smaller than sizeof(struct get_dfs_referral_rsp)
- reply with number of referrals smaller than NumberOfReferrals in the
header
Processing of such replies will cause oob.
Return -EINVAL error on such replies to prevent oob-s.
Signed-off-by: Eugene Korenevsky <ekorenevsky@aliyun.com>
Cc: stable@vger.kernel.org
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix three refcount inconsistency issues related to `cifs_sb_tlink`.
Comments for `cifs_sb_tlink` state that `cifs_put_tlink()` needs to be
called after successful calls to `cifs_sb_tlink()`. Three calls fail to
update refcount accordingly, leading to possible resource leaks.
Fixes: 8ceb984379 ("CIFS: Move rename to ops struct")
Fixes: 2f1afe2599 ("cifs: Use smb 2 - 3 and cifsacl mount options getacl functions")
Fixes: 366ed846df ("cifs: Use smb 2 - 3 and cifsacl mount options setacl function")
Cc: stable@vger.kernel.org
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Signed-off-by: Steve French <stfrench@microsoft.com>
dev->chipid is used in lan78xx_init_mac_address before it's initialized:
lan78xx_reset() {
lan78xx_init_mac_address()
lan78xx_read_eeprom()
lan78xx_read_raw_eeprom() <- dev->chipid is used here
dev->chipid = ... <- dev->chipid is initialized correctly here
}
Reorder initialization so that dev->chipid is set before calling
lan78xx_init_mac_address().
Fixes: a0db7d10b7 ("lan78xx: Add to handle mux control per chip id")
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Khalid Aziz <khalid@kernel.org>
Link: https://patch.msgid.link/20251013181648.35153-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2025-10-14
The first 2 paches are by Celeste Liu and target the gS_usb driver.
The first patch remove the limitation to 3 CAN interface per USB
device. The second patch adds the missing population of
net_device->dev_port.
The next 4 patches are by me and fix the m_can driver. They add a
missing pm_runtime_disable(), fix the CAN state transition back to
Error Active and fix the state after ifup and suspend/resume.
Another patch by me targets the m_can driver, too and replaces Dong
Aisheng's old email address.
The next 2 patches are by Vincent Mailhol and update the CAN
networking Documentation.
Tetsuo Handa contributes the last patch that add missing cleanup calls
in the NETDEV_UNREGISTER notification handler.
* tag 'linux-can-fixes-for-6.18-20251014' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: add missing calls in NETDEV_UNREGISTER notification handler
can: add Transmitter Delay Compensation (TDC) documentation
can: remove false statement about 1:1 mapping between DLC and length
can: m_can: replace Dong Aisheng's old email address
can: m_can: fix CAN state in system PM
can: m_can: m_can_chip_config(): bring up interface in correct state
can: m_can: m_can_handle_state_errors(): fix CAN state transition to Error Active
can: m_can: m_can_plat_remove(): add missing pm_runtime_disable()
can: gs_usb: gs_make_candev(): populate net_device->dev_port
can: gs_usb: increase max interface to U8_MAX
====================
Link: https://patch.msgid.link/20251014122140.990472-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bringing a linked netdevsim device down and then up causes communication
failure because both interfaces lack carrier. Basically a ifdown/ifup on
the interface make the link broken.
Commit 3762ec05a9 ("netdevsim: add NAPI support") added supported
for NAPI, calling netif_carrier_off() in nsim_stop(). This patch
re-enables the carrier symmetrically on nsim_open(), in case the device
is linked and the peer is up.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014-netdevsim_fix-v2-1-53b40590dae1@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sabrina Dubroca says:
====================
tls: misc bugfixes
Jann Horn reported multiple bugs in kTLS. This series addresses them,
and adds some corresponding selftests for those that are reproducible
(and without failure injection).
====================
Link: https://patch.msgid.link/cover.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With async crypto, we rely on tx_work to actually transmit records
once encryption completes. But while send() is running, both the
tx_lock and socket lock are held, so tx_work_handler cannot process
the queue of encrypted records, and simply reschedules itself. During
a large send(), this could last a long time, and use a lot of memory.
Transmit any pending encrypted records before restarting the main
loop of tls_sw_sendmsg_locked.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/8396631478f70454b44afb98352237d33f48d34d.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Async decryption calls tls_strp_msg_hold to create a clone of the
input skb to hold references to the memory it uses. If we fail to
allocate that clone, proceeding with async decryption can lead to
various issues (UAF on the skb, writing into userspace memory after
the recv() call has returned).
In this case, wait for all pending decryption requests.
Fixes: 84c61fe1a7 ("tls: rx: do not use the standard strparser")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/b9fe61dcc07dab15da9b35cf4c7d86382a98caf2.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When userspace wants to send a non-DATA record (via the
TLS_SET_RECORD_TYPE cmsg), we need to send any pending data from a
previous MSG_MORE send() as a separate DATA record. If that DATA record
is encrypted asynchronously, tls_handle_open_record will return
-EINPROGRESS. This is currently treated as an error by
tls_process_cmsg, and it will skip setting record_type to the correct
value, but the caller (tls_sw_sendmsg_locked) handles that return
value correctly and proceeds with sending the new message with an
incorrect record_type (DATA instead of whatever was requested in the
cmsg).
Always set record_type before handling the open record. If
tls_handle_open_record returns an error, record_type will be
ignored. If it succeeds, whether with synchronous crypto (returning 0)
or asynchronous (returning -EINPROGRESS), the caller will proceed
correctly.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/0457252e578a10a94e40c72ba6288b3a64f31662.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we hit an error during the main loop of tls_sw_sendmsg_locked (eg
failed allocation), we jump to send_end and immediately
return. Previous iterations may have queued async encryption requests
that are still pending. We should wait for those before returning, as
we could otherwise be reading from memory that userspace believes
we're not using anymore, which would be a sort of use-after-free.
This is similar to what tls_sw_recvmsg already does: failures during
the main loop jump to the "wait for async" code, not straight to the
unlock/return.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/c793efe9673b87f808d84fdefc0f732217030c52.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During tls_sw_sendmsg_locked, we pre-allocate the encrypted message
for the size we're expecting to send during the current iteration, but
we may end up sending less, for example when splicing: if we're
getting the data from small fragments of memory, we may fill up all
the slots in the skmsg with less data than expected.
In this case, we need to trim the encrypted message to only the length
we actually need, to avoid pushing uninitialized bytes down the
underlying TCP socket.
Fixes: fe1e81d4f7 ("tls/sw: Support MSG_SPLICE_PAGES")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/66a0ae99c9efc15f88e9e56c1f58f902f442ce86.1760432043.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull vfs fixes from Christian Brauner:
- Handle inode number mismatches in nsfs file handles
- Update the comment to init_file()
- Add documentation link for EBADF in the rust file code
- Skip read lock assertion for read-only filesystems when using dax
- Don't leak disconnected dentries during umount
- Fix new coredump input pattern validation
- Handle ENOIOCTLCMD conversion in vfs_fileattr_{g,s}et() correctly
- Remove redundant IOCB_DIO_CALLER_COMP clearing in overlayfs
* tag 'vfs-6.18-rc2.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
ovl: remove redundant IOCB_DIO_CALLER_COMP clearing
fs: return EOPNOTSUPP from file_setattr/file_getattr syscalls
Revert "fs: make vfs_fileattr_[get|set] return -EOPNOTSUPP"
coredump: fix core_pattern input validation
vfs: Don't leak disconnected dentries on umount
dax: skip read lock assertion for read-only filesystems
rust: file: add intra-doc link for 'EBADF'
fs: update comment in init_file()
nsfs: handle inode number mismatches gracefully in file handles
When performing memory error injection on a THP (Transparent Huge Page)
mapped to userspace on an x86 server, the kernel panics with the following
trace. The expected behavior is to terminate the affected process instead
of panicking the kernel, as the x86 Machine Check code can recover from an
in-userspace #MC.
mce: [Hardware Error]: CPU 0: Machine Check Exception: f Bank 3: bd80000000070134
mce: [Hardware Error]: RIP 10:<ffffffff8372f8bc> {memchr_inv+0x4c/0xf0}
mce: [Hardware Error]: TSC afff7bbff88a ADDR 1d301b000 MISC 80 PPIN 1e741e77539027db
mce: [Hardware Error]: PROCESSOR 0:d06d0 TIME 1758093249 SOCKET 0 APIC 0 microcode 80000320
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Data load in unrecoverable area of kernel
Kernel panic - not syncing: Fatal local machine check
The root cause of this panic is that handling a memory failure triggered
by an in-userspace #MC necessitates splitting the THP. The splitting
process employs a mechanism, implemented in
try_to_map_unused_to_zeropage(), which reads the pages in the THP to
identify zero-filled pages. However, reading the pages in the THP results
in a second in-kernel #MC, occurring before the initial memory_failure()
completes, ultimately leading to a kernel panic. See the kernel panic
call trace on the two #MCs.
First Machine Check occurs // [1]
memory_failure() // [2]
try_to_split_thp_page()
split_huge_page()
split_huge_page_to_list_to_order()
__folio_split() // [3]
remap_page()
remove_migration_ptes()
remove_migration_pte()
try_to_map_unused_to_zeropage() // [4]
memchr_inv() // [5]
Second Machine Check occurs // [6]
Kernel panic
[1] Triggered by accessing a hardware-poisoned THP in userspace, which is
typically recoverable by terminating the affected process.
[2] Call folio_set_has_hwpoisoned() before try_to_split_thp_page().
[3] Pass the RMP_USE_SHARED_ZEROPAGE remap flag to remap_page().
[4] Try to map the unused THP to zeropage.
[5] Re-access pages in the hw-poisoned THP in the kernel.
[6] Triggered in-kernel, leading to a panic kernel.
In Step[2], memory_failure() sets the poisoned flag on the page in the THP
by TestSetPageHWPoison() before calling try_to_split_thp_page().
As suggested by David Hildenbrand, fix this panic by not accessing to the
poisoned page in the THP during zeropage identification, while continuing
to scan unaffected pages in the THP for possible zeropage mapping. This
prevents a second in-kernel #MC that would cause kernel panic in Step[4].
Thanks to Andrew Zaborowski for his initial work on fixing this issue.
Link: https://lkml.kernel.org/r/20251015064926.1887643-1-qiuxu.zhuo@intel.com
Link: https://lkml.kernel.org/r/20251011075520.320862-1-qiuxu.zhuo@intel.com
Fixes: b1f202060a ("mm: remap unused subpages to shared zeropage when splitting isolated thp")
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Farrah Chen <farrah.chen@intel.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Farrah Chen <farrah.chen@intel.com>
Tested-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Acked-by: Lance Yang <lance.yang@linux.dev>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Dev Jain <dev.jain@arm.com>
Cc: Jiaqi Yan <jiaqiyan@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Mariano Pache <npache@redhat.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit 370645f41e ("dma-mapping: force bouncing if the kmalloc() size is
not cache-line-aligned") introduced DMA_BOUNCE_UNALIGNED_KMALLOC feature
and permitted architecture specific code configure kmalloc slabs with
sizes smaller than the value of dma_get_cache_alignment().
When that feature is enabled, the physical address of some small
kmalloc()-ed buffers might be not aligned to the CPU cachelines, thus not
really suitable for typical DMA. To properly handle that case a SWIOTLB
buffer bouncing is used, so no CPU cache corruption occurs. When that
happens, there is no point reporting a false-positive DMA-API warning that
the buffer is not properly aligned, as this is not a client driver fault.
[m.szyprowski@samsung.com: replace is_swiotlb_allocated() with is_swiotlb_active(), per Catalin]
Link: https://lkml.kernel.org/r/20251010173009.3916215-1-m.szyprowski@samsung.com
Link: https://lkml.kernel.org/r/20251009141508.2342138-1-m.szyprowski@samsung.com
Fixes: 370645f41e ("dma-mapping: force bouncing if the kmalloc() size is not cache-line-aligned")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Inki Dae <m.szyprowski@samsung.com>
Cc: Robin Murohy <robin.murphy@arm.com>
Cc: "Isaac J. Manjarres" <isaacmanjarres@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/damon/sysfs: fix commit test damon_ctx [de]allocation".
DAMON sysfs interface dynamically allocates and uses a damon_ctx object
for testing if given inputs for online DAMON parameters update is valid.
The object is being used without an allocation failure check, and leaked
when the test succeeds. Fix the two bugs.
This patch (of 2):
The damon_ctx for testing online DAMON parameters commit inputs is used
without its allocation failure check. This could result in an invalid
memory access. Fix it by directly returning an error when the allocation
failed.
Link: https://lkml.kernel.org/r/20251003201455.41448-1-sj@kernel.org
Link: https://lkml.kernel.org/r/20251003201455.41448-2-sj@kernel.org
Fixes: 4c9ea539ad ("mm/damon/sysfs: validate user inputs from damon_sysfs_commit_input()")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [6.15+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Both the read and write side use kiocb_done() to finish a request, and
kiocb_done() will call io_put_kbuf() in case a provided buffer was used
for the request. Provided buffers are not supported for writes, hence
NULL is being passed in. This normally works fine, as io_put_kbuf()
won't actually use the value unless REQ_F_BUFFER_RING or
REQ_F_BUFFER_SELECTED is set in the request flags. But depending on
compiler (or whether or not CONFIG_CC_OPTIMIZE_FOR_SIZE is set), that
may be done even though the value is never used. This will then cause a
NULL pointer dereference.
Make it a bit more obvious and check for a NULL io_br_sel, and don't
even bother calling io_put_kbuf() for that case.
Fixes: 5fda512554 ("io_uring/kbuf: switch to storing struct io_buffer_list locally")
Reported-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The S5_RESET_STATUS register is parsed on boot and printed to kmsg.
However, this could sometimes be misleading and lead to users wasting a
lot of time on meaningless debugging for two reasons:
* Some bits are never cleared by hardware. It's the software's
responsibility to clear them as per the Processor Programming Reference
(see [1]).
* Some rare hardware-initiated platform resets do not update the
register at all.
In both cases, a previous reboot could leave its trace in the register,
resulting in users seeing unrelated reboot reasons while debugging random
reboots afterward.
Write the read value back to the register in order to clear all reason bits
since they are write-1-to-clear while the others must be preserved.
[1]: https://bugzilla.kernel.org/show_bug.cgi?id=206537#attach_303991
[ bp: Massage commit message. ]
Fixes: ab81310287 ("x86/CPU/AMD: Print the reason for the last reset")
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/all/20250913144245.23237-1-i@rong.moe/
devm_kasprintf() may return NULL on memory allocation failure,
but the debug message prints cpus->dai_name before checking it.
Move the dev_dbg() call after the NULL check to prevent potential
NULL pointer dereference.
Fixes: cb8ea62e64 ("ASoC: amd/sdw_utils: add sof based soundwire generic machine driver")
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Link: https://patch.msgid.link/20251015075530.146851-1-liqiang01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Haibo Chen <haibo.chen@nxp.com>:
PATCH 1: different operations maybe require different max frequency, so
add flexspi to handle such case, re-config the clock rate when
new coming operation require new clock frequency.
Patch 2: add workaround for erratum ERR050272. Since only add 4us dealy
in nxp_fspi_dll_calibration(), so do not distinguish different
platforms.
Patch 3: add max frequency limitation for different sample clock source
selection. Datasheet give max 66MHz for mode 0 and 166MHz for
mode 3. And IC suggest to add this limitation on all SoCs for
safety and stability.
We should wait for the rdma_cm to become SMBDIRECT_SOCKET_DISCONNECTED,
it turns out that (at least running some xfstests e.g. cifs/001)
often triggers the case where wait_event_interruptible() returns
with -ERESTARTSYS instead of waiting for SMBDIRECT_SOCKET_DISCONNECTED
to be reached.
Or we are already in SMBDIRECT_SOCKET_DISCONNECTING and never wait
for SMBDIRECT_SOCKET_DISCONNECTED.
Fixes: 050b8c3740 ("smbd: Make upper layer decide when to destroy the transport")
Fixes: e8b3bfe9bc ("cifs: smbd: Don't destroy transport on RDMA disconnect")
Fixes: b0aa92a229 ("smb: client: make sure smbd_disconnect_rdma_work() doesn't run after smbd_destroy() took over")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Add a simple test for the corner case not currently covered by the
sticky fingers quirk. Because it's a corner case test, we only test this
on a couple of devices, not on all of them because the value of adding
the same test over and over is rather moot.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The sticky fingers quirk (MT_QUIRK_STICKY_FINGERS) was only considering
the case when slots were not released during the last report.
This can be problematic if the firmware forgets to release a finger
while others are still present.
This was observed on the Synaptics DLL0945 touchpad found on the Dell
XPS 9310 and the Dell Inspiron 5406.
Fixes: 4f4001bc76 ("HID: multitouch: fix rare Win 8 cases when the touch up event gets missing")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
HID_DG_PEN devices should have a suffix of "Stylus", as pointed out by
commit c0ee1d5716 ("HID: hid-input: Add suffix also for HID_DG_PEN").
However, on multitouch devices, these suffixes may be overridden. Before
that commit, HID_DG_PEN devices would get the "Stylus" suffix, but after
that, multitouch would override them to have an "UNKNOWN" suffix. Just add
HID_DG_PEN to the list of non-overriden suffixes in multitouch.
Before this fix:
[ 0.470981] input: ELAN9008:00 04F3:2E14 UNKNOWN as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-16/i2c-ELAN9008:00/0018:04F3:2E14.0001/input/input8
ELAN9008:00 04F3:2E14 UNKNOWN
After this fix:
[ 0.474332] input: ELAN9008:00 04F3:2E14 Stylus as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-16/i2c-ELAN9008:00/0018:04F3:2E14.0001/input/input8
ELAN9008:00 04F3:2E14 Stylus
Fixes: c0ee1d5716 ("HID: hid-input: Add suffix also for HID_DG_PEN")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 581c448476 ("HID: input: map digitizer battery usage") added
handling of battery events for digitizers (typically for batteries
presented in stylii). Digitizers typically report correct battery levels
only when stylus is actively touching the surface, and in other cases
they may report battery level of 0. To avoid confusing consumers of the
battery information the code was added to filer out reports with 0
battery levels.
However there exist other kinds of devices that may legitimately report
0 battery levels. Fix this by filtering out 0-level reports only for
digitizer usages, and continue reporting them for other kinds of devices
(Smart Batteries, etc).
Reported-by: 卢国宏 <luguohong@xiaomi.com>
Fixes: 581c448476 ("HID: input: map digitizer battery usage")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Convert test_cpu to use the newly added values_close_report() helper
to print detailed diagnostics when a tolerance check fails. This
provides clearer insight into deviations while run in the CI.
Signed-off-by: Sebastian Chlad <sebastian.chlad@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some cgroup selftests, such as test_cpu, occasionally fail by a very
small margin and if run in the CI context, it is useful to have detailed
diagnostic output to understand the deviation.
Introduce a values_close_report() helper which performs the same
comparison as values_close(), but prints detailed information when the
values differ beyond the allowed tolerance.
Signed-off-by: Sebastian Chlad <sebastian.chlad@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Inspired by commit c065b6046b ("Use CONFIG_EXT4_FS instead of
CONFIG_EXT3_FS in all of the defconfigs") I looked around for any other
left-over EXT3 config options, and found some old defconfig files still
mentioned CONFIG_EXT3_DEFAULTS_TO_ORDERED.
That config option was removed a decade ago in commit c290ea01ab ("fs:
Remove ext3 filesystem driver"). It had a good run, but let's remove it
for good.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ext4 bug fixes from Ted Ts'o:
- Fix regression caused by removing CONFIG_EXT3_FS when testing some
very old defconfigs
- Avoid a BUG_ON when opening a file on a maliciously corrupted file
system
- Avoid mm warnings when freeing a very large orphan file metadata
- Avoid a theoretical races between metadata writeback and checkpoints
(it's very hard to hit in practice, since the race requires that the
writeback take a very long time)
* tag 'ext4_for_linus-6.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
Use CONFIG_EXT4_FS instead of CONFIG_EXT3_FS in all of the defconfigs
ext4: free orphan info with kvfree
ext4: detect invalid INLINE_DATA + EXTENTS flag combination
ext4, doc: fix and improve directory hash tree description
ext4: wait for ongoing I/O to complete before freeing blocks
jbd2: ensure that all ongoing I/O complete before freeing blocks
The era of hand-rolled HIWORD_UPDATE macros is over, at least for those
drivers that use constant masks.
Like many other Rockchip drivers, rockchip-dfi brings with it its own
HIWORD_UPDATE macro. This variant doesn't shift the value (and like the
others, doesn't do any checking).
Remove it, and replace instances of it with hw_bitfield.h's
FIELD_PREP_WM16. Since FIELD_PREP_WM16 requires contiguous masks and
shifts the value for us, some reshuffling of definitions needs to
happen.
This gives us better compile-time error checking, and in my opinion,
nicer code.
Tested on an RK3568 ODROID-M1 board (LPDDR4X at 1560 MHz, an RK3588
Radxa ROCK 5B board (LPDDR4X at 2112 MHz) and an RK3588 Radxa ROCK 5T
board (LPDDR5 at 2400 MHz). perf measurements were consistent with the
measurements of stress-ng --stream in all cases.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Yury Norov (NVIDIA) <yury.norov@gmail.com>
The SCMI_XFER_FLAG_IS_RAW flag was being cleared prematurely in
scmi_xfer_raw_put() before the transfer completion was properly
acknowledged by the raw message handlers.
Move the clearing of SCMI_XFER_FLAG_IS_RAW and SCMI_XFER_FLAG_CHAN_SET
from scmi_xfer_raw_put() to __scmi_xfer_put() to ensure the flags remain
set throughout the entire raw message processing pipeline until the
transfer is returned to the free pool.
Fixes: 3095a3e25d ("firmware: arm_scmi: Add xfer helpers to provide raw access")
Suggested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Message-Id: <20251008091057.1969260-1-a.shimko.dev@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When the SCMI debug subsystem fails to initialize, the related debug root
will be missing, and the underlying descriptor will be NULL.
Handle this fault condition in the SCMI debug helpers that maintain
metrics counters.
Fixes: 0b3d48c472 ("firmware: arm_scmi: Track basic SCMI communication debug metrics")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Message-Id: <20251014115346.2391418-1-cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
There might be many reasons why a user is resizing a ring, e.g. moving
to huge pages or for some memory compaction using IORING_SETUP_NO_MMAP.
Don't bypass resizing, the user will definitely be surprised seeing 0
while the rings weren't actually moved to a new place.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_create_region_mmap_safe() protects publishing of a region against
concurrent mmap calls, however we should also protect against it when
removing a region. There is a gap io_register_mem_region() where it
safely publishes a region, but then copy_to_user goes wrong and it
unsafely frees the region.
Cc: stable@vger.kernel.org
Fixes: 087f997870 ("io_uring/memmap: implement mmap for regions")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the acquisition and release of q->elevator_lock in the
blkg_conf_open_bdev_frozen() and blkg_conf_exit_frozen() functions. The
elevator lock is no longer needed in these code paths since commit
78c271344b ("block: move wbt_enable_default() out of queue freezing
from sched ->exit()") which introduces `disk->rqos_state_mutex` for
protecting wbt state change, and not necessary to abuse elevator_lock
for this purpose.
This change helps to solve the lockdep warning reported from Yu Kuai[1].
Pass blktests/throtl with lockdep enabled.
Links: https://lore.kernel.org/linux-block/e5e7ac3f-2063-473a-aafb-4d8d43e5576e@yukuai.org.cn/ [1]
Fixes: commit 78c271344b ("block: move wbt_enable_default() out of queue freezing from sched ->exit()")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After resuming from S4, all CPUs except the boot CPU have the wrong EPP
hint programmed. This is because when the CPUs were offlined the EPP value
was reset to 0.
This is a similar problem as fixed by
commit ba3319e590 ("cpufreq/amd-pstate: Fix a regression leading to EPP
0 after resume") and the solution is also similar. When offlining rather
than reset the values to zero, reset them to match those chosen by the
policy. When the CPUs are onlined again these values will be restored.
Closes: https://community.frame.work/t/increased-power-usage-after-resuming-from-suspend-on-ryzen-7040-kernel-6-15-regression/74531/20?u=mario_limonciello
Fixes: 608a76b652 ("cpufreq/amd-pstate: Add support for the "Requested CPU Min frequency" BIOS option")
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
If a smbdirect_mr_io structure if still visible to callers of
smbd_register_mr() we can't free the related memory when the
connection is disconnected! Otherwise smbd_deregister_mr()
will crash.
Now we use a mutex and refcounting in order to keep the
memory around if the connection is disconnected.
It means smbd_deregister_mr() can be called at any later time to free
the memory, which is no longer referenced by nor referencing the
connection.
It also means smbd_destroy() no longer needs to wait for
mr_io.used.count to become 0.
Fixes: 050b8c3740 ("smbd: Make upper layer decide when to destroy the transport")
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Since commit 305853cce3 ("ksmbd: Fix race condition in RPC handle list
access"), ksmbd_session_rpc_method() attempts to lock sess->rpc_lock.
This causes hung connections / tasks when a client attempts to open
a named pipe. Using Samba's rpcclient tool:
$ rpcclient //192.168.1.254 -U user%password
$ rpcclient $> srvinfo
<connection hung here>
Kernel side:
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/0:0 state:D stack:0 pid:5021 tgid:5021 ppid:2 flags:0x00200000
Workqueue: ksmbd-io handle_ksmbd_work
Call trace:
__schedule from schedule+0x3c/0x58
schedule from schedule_preempt_disabled+0xc/0x10
schedule_preempt_disabled from rwsem_down_read_slowpath+0x1b0/0x1d8
rwsem_down_read_slowpath from down_read+0x28/0x30
down_read from ksmbd_session_rpc_method+0x18/0x3c
ksmbd_session_rpc_method from ksmbd_rpc_open+0x34/0x68
ksmbd_rpc_open from ksmbd_session_rpc_open+0x194/0x228
ksmbd_session_rpc_open from create_smb2_pipe+0x8c/0x2c8
create_smb2_pipe from smb2_open+0x10c/0x27ac
smb2_open from handle_ksmbd_work+0x238/0x3dc
handle_ksmbd_work from process_scheduled_works+0x160/0x25c
process_scheduled_works from worker_thread+0x16c/0x1e8
worker_thread from kthread+0xa8/0xb8
kthread from ret_from_fork+0x14/0x38
Exception stack(0x8529ffb0 to 0x8529fff8)
The task deadlocks because the lock is already held:
ksmbd_session_rpc_open
down_write(&sess->rpc_lock)
ksmbd_rpc_open
ksmbd_session_rpc_method
down_read(&sess->rpc_lock) <-- deadlock
Adjust ksmbd_session_rpc_method() callers to take the lock when necessary.
Fixes: 305853cce3 ("ksmbd: Fix race condition in RPC handle list access")
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The following kmemleak splat:
[ 8.105530] kmemleak: Trying to color unknown object at 0xff11000100e918c0 as Black
[ 8.106521] Call Trace:
[ 8.106521] <TASK>
[ 8.106521] dump_stack_lvl+0x4b/0x70
[ 8.106521] kvfree_call_rcu+0xcb/0x3b0
[ 8.106521] ? hrtimer_cancel+0x21/0x40
[ 8.106521] bpf_obj_free_fields+0x193/0x200
[ 8.106521] htab_map_update_elem+0x29c/0x410
[ 8.106521] bpf_prog_cfc8cd0f42c04044_overwrite_cb+0x47/0x4b
[ 8.106521] bpf_prog_8c30cd7c4db2e963_overwrite_timer+0x65/0x86
[ 8.106521] bpf_prog_test_run_syscall+0xe1/0x2a0
happens due to the combination of features and fixes, but mainly due to
commit 6d78b4473c ("bpf: Tell memcg to use allow_spinning=false path in bpf_timer_init()")
It's using __GFP_HIGH, which instructs slub/kmemleak internals to skip
kmemleak_alloc_recursive() on allocation, so subsequent kfree_rcu()->
kvfree_call_rcu()->kmemleak_ignore() complains with the above splat.
To fix this imbalance, replace bpf_map_kmalloc_node() with
kmalloc_nolock() and kfree_rcu() with call_rcu() + kfree_nolock() to
make sure that the objects allocated with kmalloc_nolock() are freed
with kfree_nolock() rather than the implicit kfree() that kfree_rcu()
uses internally.
Note, the kmalloc_nolock() happens under bpf_spin_lock_irqsave(), so
it will always fail in PREEMPT_RT. This is not an issue at the moment,
since bpf_timers are disabled in PREEMPT_RT. In the future
bpf_spin_lock will be replaced with state machine similar to
bpf_task_work.
Fixes: 6d78b4473c ("bpf: Tell memcg to use allow_spinning=false path in bpf_timer_init()")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Acked-by: Harry Yoo <harry.yoo@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: linux-mm@kvack.org
Link: https://lore.kernel.org/bpf/20251015000700.28988-1-alexei.starovoitov@gmail.com
Since the len argument value passed to exfat_ioctl_set_volume_label()
from exfat_nls_to_utf16() is passed 1 too large, an out-of-bounds read
occurs when dereferencing p_cstring in exfat_nls_to_ucs2() later.
And because of the NLS_NAME_OVERLEN macro, another error occurs when
creating a file with a period at the end using utf8 and other iocharsets.
So to avoid this, you should remove the code that uses NLS_NAME_OVERLEN
macro and make the len argument value be the length of the label string,
but with a maximum length of FSLABEL_MAX - 1.
Reported-by: syzbot+98cc76a76de46b3714d4@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=98cc76a76de46b3714d4
Fixes: d01579d590 ("exfat: Add support for FS_IOC_{GET,SET}FSLABEL")
Suggested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
In try_to_register_card(), the return value of usb_ifnum_to_if() is
passed directly to usb_interface_claimed() without a NULL check, which
will lead to a NULL pointer dereference when creating an invalid
USB audio device. Fix this by adding a check to ensure the interface
pointer is valid before passing it to usb_interface_claimed().
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Closes: https://lore.kernel.org/all/CANypQFYtQxHL5ghREs-BujZG413RPJGnO5TH=xjFBKpPts33tA@mail.gmail.com/
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The lock-related debug logic (CONFIG_LOCK_STAT) in the kernel is noting
the following warning when the BlueField-3 SOC is booted:
BUG: key ffff00008a3402a8 has not been registered!
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 4 PID: 592 at kernel/locking/lockdep.c:4801 lockdep_init_map_type+0x1d4/0x2a0
<snip>
Call trace:
lockdep_init_map_type+0x1d4/0x2a0
__kernfs_create_file+0x84/0x140
sysfs_add_file_mode_ns+0xcc/0x1cc
internal_create_group+0x110/0x3d4
internal_create_groups.part.0+0x54/0xcc
sysfs_create_groups+0x24/0x40
device_add+0x6e8/0x93c
device_register+0x28/0x40
__hwmon_device_register+0x4b0/0x8a0
devm_hwmon_device_register_with_groups+0x7c/0xe0
mlxbf_pmc_probe+0x1e8/0x3e0 [mlxbf_pmc]
platform_probe+0x70/0x110
The mlxbf_pmc driver must call sysfs_attr_init() during the
initialization of the "count_clock" data structure to avoid
this warning.
Fixes: 5efc800975 ("platform/mellanox: mlxbf-pmc: Add support for monitoring cycle count")
Reviewed-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://patch.msgid.link/20251013155605.3589770-1-davthompson@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
We found an infinite loop bug in the exFAT file system that can lead to a
Denial-of-Service (DoS) condition. When a dentry in an exFAT filesystem is
malformed, the following system calls — SYS_openat, SYS_ftruncate, and
SYS_pwrite64 — can cause the kernel to hang.
Root cause analysis shows that the size validation code in exfat_find()
does not check whether dentry.stream.valid_size is negative. As a result,
the system calls mentioned above can succeed and eventually trigger the DoS
issue.
This patch adds a check for negative dentry.stream.valid_size to prevent
this vulnerability.
Co-developed-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Co-developed-by: Jihoon Kwon <jimmyxyz010315@gmail.com>
Signed-off-by: Jihoon Kwon <jimmyxyz010315@gmail.com>
Signed-off-by: Jaehun Gou <p22gone@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Since blamed commit, unregister_netdevice_many_notify() takes the netdev
mutex if the device needs it.
If the device list is too long, this will lock more device mutexes than
lockdep can handle:
unshare -n \
bash -c 'for i in $(seq 1 100);do ip link add foo$i type dummy;done'
BUG: MAX_LOCK_DEPTH too low!
turning off the locking correctness validator.
depth: 48 max: 48!
48 locks held by kworker/u16:1/69:
#0: ..148 ((wq_completion)netns){+.+.}-{0:0}, at: process_one_work
#1: ..d40 (net_cleanup_work){+.+.}-{0:0}, at: process_one_work
#2: ..bd0 (pernet_ops_rwsem){++++}-{4:4}, at: cleanup_net
#3: ..aa8 (rtnl_mutex){+.+.}-{4:4}, at: default_device_exit_batch
#4: ..cb0 (&dev_instance_lock_key#3){+.+.}-{4:4}, at: unregister_netdevice_many_notify
[..]
Add a helper to close and then unlock a list of net_devices.
Devices that are not up have to be skipped - netif_close_many always
removes them from the list without any other actions taken, so they'd
remain in locked state.
Close devices whenever we've used up half of the tracking slots or we
processed entire list without hitting the limit.
Fixes: 7e4d784f58 ("net: hold netdev instance lock during rtnetlink operations")
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20251013185052.14021-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We started getting a crash in BPF CI, which seems to originate from
test_parse_test_list_file() test and is happening at this line:
ASSERT_OK(strcmp("test_with_spaces", set.tests[0].name), "test 0 name");
One way we can crash there is if set.cnt zero, which is checked for with
ASSERT_EQ() above, but we proceed after this regardless of the outcome.
Instead of crashing, we should bail out with test failure early.
Similarly, if parse_test_list_file() fails, we shouldn't be even looking
at set, so bail even earlier if ASSERT_OK() fails.
Fixes: 64276f01dc ("selftests/bpf: Test_progs can read test lists from file")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://lore.kernel.org/r/20251014202037.72922-1-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Traces of cxl_poison events include an hpa_alias0 field if the poison
address is in a region configured with an ELC, Extended Linear Cache.
Since the ELC always comes first in the region, the calculation needs
to subtract the ELC size from the calculated HPA address.
Fixes: 8c520c5f1e ("cxl: Add extended linear cache address alias emission for cxl events")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
The commit a43ac325c7 ("PCI: Set up bridge resources earlier") moved
bridge window resources set up earlier than before. The change was
necessary to support another change that got pulled on the last minute
due to breaking s390 and other systems.
The presence of valid bridge window resources earlier than before allows
pci_assign_unassigned_root_bus_resources() call from pci_host_probe()
assign the bridge windows. Some host bridges, however, have to wait first
for the link up event before they can enumerate successfully (see e.g.
qcom_pcie_global_irq_thread()) and thus the bus has not been enumerated yet
while calling pci_host_probe().
Calling pci_assign_unassigned_root_bus_resources() without results from
enumeration can result in sizing bridge windows with too small sizes which
cannot be later corrected after the enumeration has completed because
bridge windows have become pinned in place by the other resources.
Interestingly, it seems pci_read_bridge_bases() is not called at all in the
problematic case and the bridge window resource type setup is done by
pci_bridge_check_ranges() and sizing by the usual resource fitting logic.
The root problem behind all this looks pretty generic. If resource fitting
is called too early, the hotplug reservation and old size lower bounding
cause the bridge windows to be assigned without children but with non-zero
size, which leads to these pinning problems. As such, this can likely be
solved on the general level but the solution does not look trivial.
As the commit a43ac325c7 ("PCI: Set up bridge resources earlier") was
prequisite for other change that did not end up into kernel yet, revert it
to resolve the resource assignment failures and give time to code and test
a generic solution.
Fixes: a43ac325c7 ("PCI: Set up bridge resources earlier")
Reported-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/017ff8df-511c-4da8-b3cf-edf2cb7f1a67@packett.cool
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/df266709-a9b3-4fd8-af3a-c22eb3c9523a@roeck-us.net
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251014163602.17138-1-ilpo.jarvinen@linux.intel.com
KASAN reports a stack-out-of-bounds access in validate_region_offset()
while running the cxl-poison.sh unit test because the printk format
specifier, %pr format, is not a match for the resource_size_t type of
the variables. %pr expects struct resource pointers and attempts to
dereference the structure fields, reading beyond the bounds of the
stack variables.
Since these messages emit an 'A exceeds B' type of message, keep
the resource_size_t's and use the %pa specifier to be architecture
safe.
BUG: KASAN: stack-out-of-bounds in resource_string.isra.0+0xe9a/0x1690
[] Read of size 8 at addr ffff88800a7afb40 by task bash/1397
...
[] The buggy address belongs to stack of task bash/1397
[] and is located at offset 56 in frame:
[] validate_region_offset+0x0/0x1c0 [cxl_core]
Fixes: c3dd67681c ("cxl/region: Add inject and clear poison by region offset")
Signed-off-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
match_region_by_range() is not using the helper function that also takes
extended linear cache size into account when comparing regions. This
causes a x2 region to show up as 2 partial incomplete regions rather
than a single CXL region with extended linear cache support. Replace
the open coded compare logic with the proper helper function for
comparison. User visible impact is that when 'cxl list' is issued,
no activa CXL region(s) are shown. There may be multiple idle regions
present. No actual active CXL region is present in the kernel.
[dj: Fix stable address]
Fixes: 0ec9849b63 ("acpi/hmat / cxl: Add extended linear cache support for CXL")
Cc: stable@vger.kernel.org
Reviewed-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
The function takes two parameters and compares them. The second parameter
should be const since no modification should be done to it.
Reviewed-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
In order to compare the resource against the HMAT memory target,
the resource needs to be memory type. Change the DEFINE_RES()
macro to DEFINE_RES_MEM() in order to set the correct resource type.
hmat_get_extended_linear_cache_size() uses resource_contains()
internally. This causes a regression for platforms with the
extended linear cache enabled as the comparison always fails and the
cache size is not set. User visible impact is that when 'cxl list' is
issued, a CXL region with extended linear cache support will only
report half the size of the actual size. And this also breaks MCE
reporting of the memory region due to incorrect offset calculation
for the memory.
[dj: Fixup commit log suggested by djbw]
[dj: Fixup stable address for cc]
Fixes: 12b3d697c8 ("cxl: Remove core/acpi.c and cxl core dependency on ACPI")
Cc: stable@vger.kernel.org
Reviewed-by: Gregory Price <gourry@gourry.net>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fix a memory leak in bpf_prog_test_run_xdp() where the context buffer
allocated by bpf_ctx_init() is not freed when the function returns early
due to a data size check.
On the failing path:
ctx = bpf_ctx_init(...);
if (kattr->test.data_size_in - meta_sz < ETH_HLEN)
return -EINVAL;
The early return bypasses the cleanup label that kfree()s ctx, leading to a
leak detectable by kmemleak under fuzzing. Change the return to jump to the
existing free_ctx label.
Fixes: fe9544ed1a ("bpf: Support specifying linear xdp packet data size for BPF_PROG_TEST_RUN")
Reported-by: BPF Runtime Fuzzer (BRF)
Signed-off-by: Shardul Bankar <shardulsb08@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/20251014120037.1981316-1-shardulsb08@gmail.com
defer_free() links pending objects using the slab's freelist offset
which is fine as they are not free yet. free_deferred_objects() then
clears this pointer to avoid confusing the debugging consistency checks
that may be enabled for the cache.
However, with CONFIG_SLAB_FREELIST_HARDENED, even the NULL pointer needs
to be encoded appropriately using set_freepointer(), otherwise it's
decoded as something else and triggers the consistency checks, as found
by the kernel test robot.
Use set_freepointer() to prevent the issue.
Fixes: af92793e52 ("slab: Introduce kmalloc_nolock() and kfree_nolock().")
Reported-and-tested-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202510101652.7921fdc6-lkp@intel.com
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Pull nfsd fix from Chuck Lever:
- Fix a crasher reported by rtm@csail.mit.edu
* tag 'nfsd-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Define a proc_layoutcommit for the FlexFiles layout type
Pull IPMI fixes from Corey Minyard:
"A few bug fixes for patches that went in this release: a refcount
error and some missing or incorrect error checks"
* tag 'for-linus-6.18-2' of https://github.com/cminyard/linux-ipmi:
ipmi: Fix handling of messages with provided receive message pointer
mfd: ls2kbmc: check for devm_mfd_add_devices() failure
mfd: ls2kbmc: Fix an IS_ERR() vs NULL check in probe()
The sc_c field is currently not updated in the host response to the
controller challenge leading to failures while attempting secure
channel concatenation. Fix this by adding a new sc_c variable to the
dhchap queue context structure which is appropriately set during
negotiate and then used in the host response.
Fixes: e88a7595b5 ("nvme-tcp: request secure channel concatenation")
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Prashanth Adurthi <prashana@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Currently, if find_and_map_user_pages() takes a DMA xfer request from the
user with a length field set to 0, or in a rare case, the host receives
QAIC_TRANS_DMA_XFER_CONT from the device where resources->xferred_dma_size
is equal to the requested transaction size, the function will return 0
before allocating an sgt or setting the fields of the dma_xfer struct.
In that case, encode_addr_size_pairs() will try to access the sgt which
will lead to a general protection fault.
Return an EINVAL in case the user provides a zero-sized ALP, or the device
requests continuation after all of the bytes have been transferred.
Fixes: 96d3c1cade ("accel/qaic: Clean up integer overflow checking in map_user_pages()")
Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com>
Signed-off-by: Youssef Samir <youssef.abdulrahman@oss.qualcomm.com>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Reviewed-by: Carl Vanderlip <carl.vanderlip@oss.qualcomm.com>
Signed-off-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251007122320.339654-1-youssef.abdulrahman@oss.qualcomm.com
Fix spelling of CIP_NO_HEADER to prevent a kernel-doc warning.
Warning: amdtp-stream.h:57 Enum value 'CIP_NO_HEADER' not described in enum 'cip_flags'
Warning: amdtp-stream.h:57 Excess enum value '%CIP_NO_HEADERS' description in 'cip_flags'
Fixes: 3b196c394d ("ALSA: firewire-lib: add no-header packet processing")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The jq command is used in vlan_bridge_binding.sh, if it is not supported,
the test will spam the following log.
# ./vlan_bridge_binding.sh: line 51: jq: command not found
# ./vlan_bridge_binding.sh: line 51: jq: command not found
# ./vlan_bridge_binding.sh: line 51: jq: command not found
# ./vlan_bridge_binding.sh: line 51: jq: command not found
# ./vlan_bridge_binding.sh: line 51: jq: command not found
# TEST: Test bridge_binding on->off when lower down [FAIL]
# Got operstate of , expected 0
The rtnetlink.sh has the same problem. It makes sense to check if jq is
installed before running these tests. After this patch, the
vlan_bridge_binding.sh skipped if jq is not supported:
# timeout set to 3600
# selftests: net: vlan_bridge_binding.sh
# TEST: jq not installed [SKIP]
Fixes: dca12e9ab7 ("selftests: net: Add a VLAN bridge binding selftest")
Fixes: 6a414fd77f ("selftests: rtnetlink: Add an address proto test")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20251013080039.3035898-1-wangliang74@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The check for some lost idle pelt time should be always done when
pick_next_task_fair() fails to pick a task and not only when we call it
from the fair fast-path.
The case happens when the last running task on rq is a RT or DL task. When
the latter goes to sleep and the /Sum of util_sum of the rq is at the max
value, we don't account the lost of idle time whereas we should.
Fixes: 67692435c4 ("sched: Rework pick_next_task() slow-path")
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
IBM CI tool reported kernel warning[1] when running a CPU removal
operation through drmgr[2]. i.e "drmgr -c cpu -r -q 1"
WARNING: CPU: 0 PID: 0 at kernel/sched/cpudeadline.c:219 cpudl_set+0x58/0x170
NIP [c0000000002b6ed8] cpudl_set+0x58/0x170
LR [c0000000002b7cb8] dl_server_timer+0x168/0x2a0
Call Trace:
[c000000002c2f8c0] init_stack+0x78c0/0x8000 (unreliable)
[c0000000002b7cb8] dl_server_timer+0x168/0x2a0
[c00000000034df84] __hrtimer_run_queues+0x1a4/0x390
[c00000000034f624] hrtimer_interrupt+0x124/0x300
[c00000000002a230] timer_interrupt+0x140/0x320
Git bisects to: commit 4ae8d9aa9f ("sched/deadline: Fix dl_server getting stuck")
This happens since:
- dl_server hrtimer gets enqueued close to cpu offline, when
kthread_park enqueues a fair task.
- CPU goes offline and drmgr removes it from cpu_present_mask.
- hrtimer fires and warning is hit.
Fix it by stopping the dl_server before CPU is marked dead.
[1]: https://lore.kernel.org/all/8218e149-7718-4432-9312-f97297c352b9@linux.ibm.com/
[2]: https://github.com/ibm-power-utilities/powerpc-utils/tree/next/src/drmgr
[sshegde: wrote the changelog and tested it]
Fixes: 4ae8d9aa9f ("sched/deadline: Fix dl_server getting stuck")
Closes: https://lore.kernel.org/all/8218e149-7718-4432-9312-f97297c352b9@linux.ibm.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Shrikanth Hegde <sshegde@linux.ibm.com>
There is a spelling mistake in HID description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Completion napi can free out-of-order tx descriptors if hw QoS is
enabled and packets with different priority are queued to same DMA ring.
Take into account possible out-of-order reports checking if the tx queue
is full using circular buffer head/tail pointer instead of the number of
queued packets.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251012-airoha-tx-busy-queue-v2-1-a600b08bab2d@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Neal reported that using neper tcp_stream with TCP_TX_DELAY
set to 50ms would often lead to flows stuck in a small cwnd mode,
regardless of the congestion control.
While tcp_stream sets TCP_TX_DELAY too late after the connect(),
it highlighted two kernel bugs.
The following heuristic in tcp_tso_should_defer() seems wrong
for large RTT:
delta = tp->tcp_clock_cache - head->tstamp;
/* If next ACK is likely to come too late (half srtt), do not defer */
if ((s64)(delta - (u64)NSEC_PER_USEC * (tp->srtt_us >> 4)) < 0)
goto send_now;
If next ACK is expected to come in more than 1 ms, we should
not defer because we prefer a smooth ACK clocking.
While blamed commit was a step in the good direction, it was not
generic enough.
Another patch fixing TCP_TX_DELAY for established flows
will be proposed when net-next reopens.
Fixes: 50c8339e92 ("tcp: tso: restore IW10 after TSO autosizing")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20251011115742.1245771-1-edumazet@google.com
[pabeni@redhat.com: fixed whitespace issue]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Temporarily change CONFIG_HID_HAPTIC to be bool instead of tristate, until
we implement a permanent solution.
Recently the CONFIG_HID_HAPTIC Kconfig option was reported as causing
the following build errors:
MODPOST Module.symvers
ERROR: modpost: "hid_haptic_init" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_pressure_increase" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_check_pressure_unit" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_input_configured" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_input_mapping" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_feature_mapping" [drivers/hid/hid-multitouch.ko] undefined!
ERROR: modpost: "hid_haptic_pressure_reset" [drivers/hid/hid-multitouch.ko] undefined!
make[3]: *** [/home/thl/var/linux.dev/scripts/Makefile.modpost:147: Module.symvers] Error 1
when the kernel is compiled with the following configuration:
CONFIG_HID=y
CONFIG_HID_MULTITOUCH=m
CONFIG_HID_HAPTIC=m
To resolve this, temporarily change the CONFIG_HID_HAPTIC option to be
bool, until we arrive at a permanent solution to enable CONFIG_HID_HAPTIC
to be tristate.
For a more detailed discussion, see [1].
[1]: https://lore.kernel.org/linux-input/auypydfkhx2eg7vp764way4batdilzc35inqda3exwzs3tk3ff@oagat6g46zto/
Signed-off-by: Jonathan Denose <jdenose@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some controllers are very bad at updating the IMU, leading to these
messages spamming the syslog. Rate-limiting them helps with this a bit.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some third-party controllers, such as the PB Tails CHOC, won't always
respond quickly on startup. Since this packet is needed for probe, and only
once during probe, let's just wait an extra second, which makes connecting
consistent.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
hid_warn_ratelimited() is needed. Add the others as part of the block.
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch adds ALWAYS_POLL quirk for the VRS R295 steering wheel joystick.
This device reboots itself every 8-10 seconds if it is not polled.
Signed-off-by: Oleg Makarenko <oleg@makarenk.ooo>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Cooler Master Mice Dongle includes a vendor defined HID interface
alongside its mouse interface. Not polling it will cause the mouse to
stop responding to polls on any interface once woken up again after
going into power saving mode.
Add the HID_QUIRK_ALWAYS_POLL quirk alongside the Cooler Master VID and
the Dongle's PID.
Signed-off-by: Tristan Lobb <tristan.lobb@it-lobb.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The original implementation used level detection for the first interrupt
after device reset to avoid potential interrupt line noise and missed
interrupts during the initialization phase. However, this approach
introduced unintended side effects when tested with certain touch panels,
including:
- Delayed hardware interrupt response
- Multiple spurious interrupt triggers
Switching back to edge detection for the first interrupt resolves these
issues while maintaining reliable interrupt handling.
Extensive testing across multiple platforms with touch panels from
various vendors confirms this change introduces no regressions.
[jkosina@suse.com: properly capitalize shortlog]
Fixes: 9d8d51735a ("HID: intel-thc-hid: intel-quickspi: Add HIDSPI protocol implementation")
Tested-by: Rui Zhang <rui1.zhang@intel.com>
Signed-off-by: Even Xu <even.xu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some file systems like FUSE-based ones or overlayfs may record the backing
file in struct vm_area_struct vm_file, instead of the user file that the
user mmapped.
That causes perf to misreport the device major/minor numbers of the file
system of the file, and the generation of the file, and potentially other
inode details. There is an existing helper file_user_inode() for that
situation.
Use file_user_inode() instead of file_inode() to get the inode for MMAP2
events.
Example:
Setup:
# cd /root
# mkdir test ; cd test ; mkdir lower upper work merged
# cp `which cat` lower
# mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir=work merged
# perf record -e cycles:u -- /root/test/merged/cat /proc/self/maps
...
55b2c91d0000-55b2c926b000 r-xp 00018000 00:1a 3419 /root/test/merged/cat
...
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.004 MB perf.data (5 samples) ]
#
# stat /root/test/merged/cat
File: /root/test/merged/cat
Size: 1127792 Blocks: 2208 IO Block: 4096 regular file
Device: 0,26 Inode: 3419 Links: 1
Access: (0755/-rwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2025-09-08 12:23:59.453309624 +0000
Modify: 2025-09-08 12:23:59.454309624 +0000
Change: 2025-09-08 12:23:59.454309624 +0000
Birth: 2025-09-08 12:23:59.453309624 +0000
Before:
Device reported 00:02 differs from stat output and /proc/self/maps
# perf script --show-mmap-events | grep /root/test/merged/cat
cat 377 [-01] 243.078558: PERF_RECORD_MMAP2 377/377: [0x55b2c91d0000(0x9b000) @ 0x18000 00:02 3419 2068525940]: r-xp /root/test/merged/cat
After:
Device reported 00:1a is the same as stat output and /proc/self/maps
# perf script --show-mmap-events | grep /root/test/merged/cat
cat 362 [-01] 127.755167: PERF_RECORD_MMAP2 362/362: [0x55ba6e781000(0x9b000) @ 0x18000 00:1a 3419 0]: r-xp /root/test/merged/cat
With respect to stable kernels, overlayfs mmap function ovl_mmap() was
added in v4.19 but file_user_inode() was not added until v6.8 and never
back-ported to stable kernels. FMODE_BACKING that it depends on was added
in v6.5. This issue has gone largely unnoticed, so back-porting before
v6.8 is probably not worth it, so put 6.8 as the stable kernel prerequisite
version, although in practice the next long term kernel is 6.12.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Amir Goldstein <amir73il@gmail.com>
Cc: stable@vger.kernel.org # 6.8
Some file systems like FUSE-based ones or overlayfs may record the backing
file in struct vm_area_struct vm_file, instead of the user file that the
user mmapped.
Since commit def3ae83da ("fs: store real path instead of fake path in
backing file f_path"), file_path() no longer returns the user file path
when applied to a backing file. There is an existing helper
file_user_path() for that situation.
Use file_user_path() instead of file_path() to get the path for MMAP
and MMAP2 events.
Example:
Setup:
# cd /root
# mkdir test ; cd test ; mkdir lower upper work merged
# cp `which cat` lower
# mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir=work merged
# perf record -e intel_pt//u -- /root/test/merged/cat /proc/self/maps
...
55b0ba399000-55b0ba434000 r-xp 00018000 00:1a 3419 /root/test/merged/cat
...
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.060 MB perf.data ]
#
Before:
File name is wrong (/cat), so decoding fails:
# perf script --no-itrace --show-mmap-events
cat 367 [016] 100.491492: PERF_RECORD_MMAP2 367/367: [0x55b0ba399000(0x9b000) @ 0x18000 00:02 3419 489959280]: r-xp /cat
...
# perf script --itrace=e | wc -l
Warning:
19 instruction trace errors
19
#
After:
File name is correct (/root/test/merged/cat), so decoding is ok:
# perf script --no-itrace --show-mmap-events
cat 364 [016] 72.153006: PERF_RECORD_MMAP2 364/364: [0x55ce4003d000(0x9b000) @ 0x18000 00:02 3419 3132534314]: r-xp /root/test/merged/cat
# perf script --itrace=e
# perf script --itrace=e | wc -l
0
#
Fixes: def3ae83da ("fs: store real path instead of fake path in backing file f_path")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Amir Goldstein <amir73il@gmail.com>
Cc: stable@vger.kernel.org
It was reported that Intel PT address filters do not work in Docker
containers. That relates to the use of overlayfs.
overlayfs records the backing file in struct vm_area_struct vm_file,
instead of the user file that the user mmapped. In order for an address
filter to match, it must compare to the user file inode. There is an
existing helper file_user_inode() for that situation.
Use file_user_inode() instead of file_inode() to get the inode for address
filter matching.
Example:
Setup:
# cd /root
# mkdir test ; cd test ; mkdir lower upper work merged
# cp `which cat` lower
# mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir=work merged
# perf record --buildid-mmap -e intel_pt//u --filter 'filter * @ /root/test/merged/cat' -- /root/test/merged/cat /proc/self/maps
...
55d61d246000-55d61d2e1000 r-xp 00018000 00:1a 3418 /root/test/merged/cat
...
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.015 MB perf.data ]
# perf buildid-cache --add /root/test/merged/cat
Before:
Address filter does not match so there are no control flow packets
# perf script --itrace=e
# perf script --itrace=b | wc -l
0
# perf script -D | grep 'TIP.PGE' | wc -l
0
#
After:
Address filter does match so there are control flow packets
# perf script --itrace=e
# perf script --itrace=b | wc -l
235
# perf script -D | grep 'TIP.PGE' | wc -l
57
#
With respect to stable kernels, overlayfs mmap function ovl_mmap() was
added in v4.19 but file_user_inode() was not added until v6.8 and never
back-ported to stable kernels. FMODE_BACKING that it depends on was added
in v6.5. This issue has gone largely unnoticed, so back-porting before
v6.8 is probably not worth it, so put 6.8 as the stable kernel prerequisite
version, although in practice the next long term kernel is 6.12.
Closes: https://lore.kernel.org/linux-perf-users/aBCwoq7w8ohBRQCh@fremen.lan
Reported-by: Edd Barrett <edd@theunixzoo.co.uk>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Amir Goldstein <amir73il@gmail.com>
Cc: stable@vger.kernel.org # 6.8
It's less confusing to optimize uprobe right after handlers execution
and before we do the check for changed ip register to avoid situations
where changed ip register would skip uprobe optimization.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
During interface toggle operations (ifdown/ifup), the driver currently
resets the local helper variable 'phy_link' to -1. This causes the link
state machine to incorrectly interpret the state as a link change event,
resulting in spurious "Link is down" messages being logged when the
interface is brought back up.
Preserve the phy_link state across interface toggles to avoid treating
the -1 sentinel value as a legitimate link state transition.
Fixes: 88131a812b ("amd-xgbe: Perform phy connect/disconnect at dev open/stop")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Link: https://patch.msgid.link/20251010065142.1189310-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DbC is currently only enabled back if it's in configured state during
suspend.
If system is suspended after DbC is enabled, but before the device is
properly enumerated by the host, then DbC would not be enabled back in
resume.
Always enable DbC back in resume if it's suspended in enabled,
connected, or configured state
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DbC may add 1024 bogus bytes to the beginneing of the receiving endpoint
if DbC hw triggers a STALL event before any Transfer Blocks (TRBs) for
incoming data are queued, but driver handles the event after it queued
the TRBs.
This is possible as xHCI DbC hardware may trigger spurious STALL transfer
events even if endpoint is empty. The STALL event contains a pointer
to the stalled TRB, and "remaining" untransferred data length.
As there are no TRBs queued yet the STALL event will just point to first
TRB position of the empty ring, with '0' bytes remaining untransferred.
DbC driver is polling for events, and may not handle the STALL event
before /dev/ttyDBC0 is opened and incoming data TRBs are queued.
The DbC event handler will now assume the first queued TRB (length 1024)
has stalled with '0' bytes remaining untransferred, and copies the data
This race situation can be practically mitigated by making sure the event
handler handles all pending transfer events when DbC reaches configured
state, and only then create dev/ttyDbC0, and start queueing transfers.
The event handler can this way detect the STALL events on empty rings
and discard them before any transfers are queued.
This does in practice solve the issue, but still leaves a small possible
gap for the race to trigger.
We still need a way to distinguish spurious STALLs on empty rings with '0'
bytes remaing, from actual STALL events with all bytes transmitted.
Cc: stable <stable@kernel.org>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have two ways to identify CPUs that only implement FEAT_VHE
and not FEAT_E2H0:
- either they advertise it via ID_AA64MMFR4_EL1.E2H0,
- or the HCR_EL2.E2H bit is RAO/WI
However, there is a third category of "cpus" that fall between these
two cases: on CPUs that do not implement FEAT_FGT, it is IMPDEF whether
an access to ID_AA64MMFR4_EL1 can trap to EL2 when the register value
is zero.
A consequence of this is that on systems such as Neoverse V2, a NV
guest cannot reliably detect that it is in a VHE-only configuration
(E2H is writable, and ID_AA64MMFR0_EL1 is 0), despite the hypervisor's
best effort to repaint the id register.
Replace the RAO/WI test by a sequence that makes use of the VHE
register remnapping between EL1 and EL2 to detect this situation,
and work out whether we get the VHE behaviour even after having
set HCR_EL2.E2H to 0.
This solves the NV problem, and provides a more reliable acid test
for CPUs that do not completely follow the letter of the architecture
while providing a RES1 behaviour for HCR_EL2.E2H.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Tested-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/15A85F2B-1A0C-4FA7-9FE4-EEC2203CC09E@global.cadence.com
Commit d6ace46c82 ("ext4: remove obsolete EXT3 config options")
removed the obsolete EXT3_CONFIG options, since it had been over a
decade since fs/ext3 had been removed. Unfortunately, there were a
number of defconfigs that still used CONFIG_EXT3_FS which the cleanup
commit didn't fix up. This led to a large number of defconfig test
builds to fail. Oops.
Fixes: d6ace46c82 ("ext4: remove obsolete EXT3 config options")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Jacob Keller says:
====================
Intel Wired LAN Driver Updates 2025-10-01 (idpf, ixgbe, ixgbevf)
For idpf:
Milena fixes a memory leak in the idpf reset logic when the driver resets
with an outstanding Tx timestamp.
For ixgbe and ixgbevf:
Jedrzej fixes an issue with reporting link speed on E610 VFs.
Jedrzej also fixes the VF mailbox API incompatibilities caused by the
confusion with API v1.4, v1.5, and v1.6. The v1.4 API introduced IPSEC
offload, but this was only supported on Linux hosts. The v1.5 API
introduced a new mailbox API which is necessary to resolve issues on ESX
hosts. The v1.6 API introduced a new link management API for E610. Jedrzej
introduces a new v1.7 API with a feature negotiation which enables properly
checking if features such as IPSEC or the ESX mailbox APIs are supported.
This resolves issues with compatibility on different hosts, and aligns the
API across hosts instead of having Linux require custom mailbox API
versions for IPSEC offload.
Koichiro fixes a KASAN use-after-free bug in ixgbe_remove().
====================
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-0-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc95 ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f289641 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit
d0725312ad ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/20241101-jk-ixgbevf-mailbox-v1-5-fixes-v1-0-f556dc9a66ed@intel.com/
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-4-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver requests Tx timestamp value, one of the first steps is
to clone SKB using skb_get. It increases the reference counter for that
SKB to prevent unexpected freeing by another component.
However, there may be a case where the index is requested, SKB is
assigned and never consumed by PTP flows - for example due to reset during
running PTP apps.
Add a check in release timestamping function to verify if the SKB
assigned to Tx timestamp latch was freed, and release remaining SKBs.
Fixes: 4901e83a94 ("idpf: add Tx timestamp capabilities negotiation")
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-1-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to ipv4 tunnel, ipv6 version updates dev->needed_headroom, too.
While ipv4 tunnel headroom adjustment growth was limited in
commit 5ae1e9922b ("net: ip_tunnel: prevent perpetual headroom growth"),
ipv6 tunnel yet increases the headroom without any ceiling.
Reflect ipv4 tunnel headroom adjustment limit on ipv6 version.
Credits to Francesco Ruggeri, who was originally debugging this issue
and wrote local Arista-specific patch and a reproducer.
Fixes: 8eb30be035 ("ipv6: Create ip6_tnl_xmit")
Cc: Florian Westphal <fw@strlen.de>
Cc: Francesco Ruggeri <fruggeri05@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://patch.msgid.link/20251009-ip6_tunnel-headroom-v2-1-8e4dbd8f7e35@arista.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46dde ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the internal flash contains missing or corrupted configuration,
basic communication over the bus still functions, but the device
is not capable of normal operation (for example, using mailboxes).
This condition is indicated in the info register by the ready bit.
If this bit is cleared, the probe procedure times out while fetching
the device state.
Handle this case by checking the ready bit value in zl3073x_dev_start()
and skipping DPLL device and pin registration if it is cleared.
Do not report this condition as an error, allowing the devlink device
to be registered and enabling the user to flash the correct configuration.
Prior this patch:
[ 31.112299] zl3073x-i2c 1-0070: Failed to fetch input state: -ETIMEDOUT
[ 31.116332] zl3073x-i2c 1-0070: error -ETIMEDOUT: Failed to start device
[ 31.136881] zl3073x-i2c 1-0070: probe with driver zl3073x-i2c failed with error -110
After this patch:
[ 41.011438] zl3073x-i2c 1-0070: FW not fully ready - missing or corrupted config
Fixes: 75a71ecc24 ("dpll: zl3073x: Register DPLL devices and pins")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251008141445.841113-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assuming the disk layout as below,
disk0: 0 --- 0x00035abfff
disk1: 0x00035ac000 --- 0x00037abfff
disk2: 0x00037ac000 --- 0x00037ebfff
and we want to read data from offset=13568 having len=128 across the block
devices, we can illustrate the block addresses like below.
0 .. 0x00037ac000 ------------------- 0x00037ebfff, 0x00037ec000 -------
| ^ ^ ^
| fofs 0 13568 13568+128
| ------------------------------------------------------
| LBA 0x37e8aa9 0x37ebfa9 0x37ec029
--- map 0x3caa9 0x3ffa9
In this example, we should give the relative map of the target block device
ranging from 0x3caa9 to 0x3ffa9 where the length should be calculated by
0x37ebfff + 1 - 0x37ebfa9.
In the below equation, however, map->m_pblk was supposed to be the original
address instead of the one from the target block address.
- map->m_len = min(map->m_len, dev->end_blk + 1 - map->m_pblk);
Cc: stable@vger.kernel.org
Fixes: 71f2c82062 ("f2fs: multidevice: support direct IO")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
iput() calls the problematic routine, which does a ->i_count inc/dec
cycle. Undoing it with iput() recurses into the problem.
Note f2fs should not be playing games with the refcount to begin with,
but that will be handled later. Right now solve the immediate
regression.
Fixes: bc986b1d75 ("fs: stop accessing ->i_count directly in f2fs and gfs2")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202509301450.138b448f-lkp@intel.com
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The change to have cpa_flush() call flush_kernel_pages() introduced
a bug where __cpa_addr() can access an address one larger than the
largest one in the cpa->pages array.
KASAN reports the issue like this:
BUG: KASAN: slab-out-of-bounds in __cpa_addr arch/x86/mm/pat/set_memory.c:309 [inline]
BUG: KASAN: slab-out-of-bounds in __cpa_addr+0x1d3/0x220 arch/x86/mm/pat/set_memory.c:306
Read of size 8 at addr ffff88801f75e8f8 by task syz.0.17/5978
This bug could cause cpa_flush() to not properly flush memory,
which somehow never showed any symptoms in my tests, possibly
because cpa_flush() is called so rarely, but could potentially
cause issues for other people.
Fix the issue by directly calculating the flush end address
from the start address.
Fixes: 86e6815b31 ("x86/mm: Change cpa_flush() to call flush_kernel_range() directly")
Reported-by: syzbot+afec6555eef563c66c97@syzkaller.appspotmail.com
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kiryl Shutsemau <kas@kernel.org>
Link: https://lore.kernel.org/all/68e2ff90.050a0220.2c17c1.0038.GAE@google.com/
cxl EDAC calls cxl_feature_info() to get the feature information and
if the hardware has no Features support, cxlfs may be passed in as
NULL.
[ 51.957498] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 51.965571] #PF: supervisor read access in kernel mode
[ 51.971559] #PF: error_code(0x0000) - not-present page
[ 51.977542] PGD 17e4f6067 P4D 0
[ 51.981384] Oops: Oops: 0000 [#1] SMP NOPTI
[ 51.986300] CPU: 49 UID: 0 PID: 3782 Comm: systemd-udevd Not tainted 6.17.0dj
test+ #64 PREEMPT(voluntary)
[ 51.997355] Hardware name: <removed>
[ 52.009790] RIP: 0010:cxl_feature_info+0xa/0x80 [cxl_core]
Add a check for cxlfs before dereferencing it and return -EOPNOTSUPP if
there is no cxlfs created due to no hardware support.
Fixes: eb5dfcb9e3 ("cxl: Add support to handle user feature commands for set feature")
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
The warning -Wflex-array-member-not-at-end was introduced in GCC-14, and
we are getting ready to enable it, globally.
Fix the following warning:
fs/btrfs/send.c:181:24: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
and move the declaration of send_ctx::cur_inode_path to the end.
Notice that struct fs_path contains a flexible array member inline_buf,
but also a padding array and a limit calculated for the usable space of
inline_buf (FS_PATH_INLINE_SIZE). It is not the pattern where flexible
array is in the middle of a structure and could potentially overwrite
other members.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The parentheses for the unlikely() annotation were put in the wrong
place so it means that the condition is basically never true and the
bounds checking is skipped.
Fixes: aab9458b9f ("btrfs: tree-checker: add inode extref checks")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
At the end of btrfs_load_block_group_zone_info() the first thing we do
is to ensure that if the mapping type is not a SINGLE one and there is
no RAID stripe tree, then we return early with an error.
Doing that, though, prevents the code from running the last calls from
this function which are about freeing memory allocated during its
run. Hence, in this case, instead of returning early, we set the ret
value and fall through the rest of the cleanup code.
Fixes: 5906333cc4 ("btrfs: zoned: don't skip block group profile checks on conventional zones")
CC: stable@vger.kernel.org # 6.8+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Miquel Sabaté Solà <mssola@mssola.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The intent of btrfs_readahead_expand() was to expand to the length of
the current compressed extent being read. However, "ram_bytes" is *not*
that, in the case where a single physical compressed extent is used for
multiple file extents.
Consider this case with a large compressed extent C and then later two
non-compressed extents N1 and N2 written over C, leaving C1 and C2
pointing to offset/len pairs of C:
[ C ]
[ N1 ][ C1 ][ N2 ][ C2 ]
In such a case, ram_bytes for both C1 and C2 is the full uncompressed
length of C. So starting readahead in C1 will expand the readahead past
the end of C1, past N2, and into C2. This will then expand readahead
again, to C2_start + ram_bytes, way past EOF. First of all, this is
totally undesirable, we don't want to read the whole file in arbitrary
chunks of the large underlying extent if it happens to exist. Secondly,
it results in zeroing the range past the end of C2 up to ram_bytes. This
is particularly unpleasant with fs-verity as it can zero and set
uptodate pages in the verity virtual space past EOF. This incorrect
readahead behavior can lead to verity verification errors, if we iterate
in a way that happens to do the wrong readahead.
Fix this by using em->len for readahead expansion, not em->ram_bytes,
resulting in the expected behavior of stopping readahead at the extent
boundary.
Reported-by: Max Chernoff <git@maxchernoff.ca>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2399898
Fixes: 9e9ff875e4 ("btrfs: use readahead_expand() on compressed extents")
CC: stable@vger.kernel.org # 6.17
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, when building a free space tree at populate_free_space_tree(),
if we are not using the block group tree feature, we always expect to find
block group items (either extent items or a block group item with key type
BTRFS_BLOCK_GROUP_ITEM_KEY) when we search the extent tree with
btrfs_search_slot_for_read(), so we assert that we found an item. However
this expectation is wrong since we can have a new block group created in
the current transaction which is still empty and for which we still have
not added the block group's item to the extent tree, in which case we do
not have any items in the extent tree associated to the block group.
The insertion of a new block group's block group item in the extent tree
happens at btrfs_create_pending_block_groups() when it calls the helper
insert_block_group_item(). This typically is done when a transaction
handle is released, committed or when running delayed refs (either as
part of a transaction commit or when serving tickets for space reservation
if we are low on free space).
So remove the assertion at populate_free_space_tree() even when the block
group tree feature is not enabled and update the comment to mention this
case.
Syzbot reported this with the following stack trace:
BTRFS info (device loop3 state M): rebuilding free space tree
assertion failed: ret == 0 :: 0, in fs/btrfs/free-space-tree.c:1115
------------[ cut here ]------------
kernel BUG at fs/btrfs/free-space-tree.c:1115!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 1 UID: 0 PID: 6352 Comm: syz.3.25 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
RIP: 0010:populate_free_space_tree+0x700/0x710 fs/btrfs/free-space-tree.c:1115
Code: ff ff e8 d3 (...)
RSP: 0018:ffffc9000430f780 EFLAGS: 00010246
RAX: 0000000000000043 RBX: ffff88805b709630 RCX: fea61d0e2e79d000
RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000
RBP: ffffc9000430f8b0 R08: ffffc9000430f4a7 R09: 1ffff92000861e94
R10: dffffc0000000000 R11: fffff52000861e95 R12: 0000000000000001
R13: 1ffff92000861f00 R14: dffffc0000000000 R15: 0000000000000000
FS: 00007f424d9fe6c0(0000) GS:ffff888125afc000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd78ad212c0 CR3: 0000000076d68000 CR4: 00000000003526f0
Call Trace:
<TASK>
btrfs_rebuild_free_space_tree+0x1ba/0x6d0 fs/btrfs/free-space-tree.c:1364
btrfs_start_pre_rw_mount+0x128f/0x1bf0 fs/btrfs/disk-io.c:3062
btrfs_remount_rw fs/btrfs/super.c:1334 [inline]
btrfs_reconfigure+0xaed/0x2160 fs/btrfs/super.c:1559
reconfigure_super+0x227/0x890 fs/super.c:1076
do_remount fs/namespace.c:3279 [inline]
path_mount+0xd1a/0xfe0 fs/namespace.c:4027
do_mount fs/namespace.c:4048 [inline]
__do_sys_mount fs/namespace.c:4236 [inline]
__se_sys_mount+0x313/0x410 fs/namespace.c:4213
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f424e39066a
Code: d8 64 89 02 (...)
RSP: 002b:00007f424d9fde68 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 00007f424d9fdef0 RCX: 00007f424e39066a
RDX: 0000200000000180 RSI: 0000200000000380 RDI: 0000000000000000
RBP: 0000200000000180 R08: 00007f424d9fdef0 R09: 0000000000000020
R10: 0000000000000020 R11: 0000000000000246 R12: 0000200000000380
R13: 00007f424d9fdeb0 R14: 0000000000000000 R15: 00002000000002c0
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
Reported-by: syzbot+884dc4621377ba579a6f@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/68dc3dab.a00a0220.102ee.004e.GAE@google.com/
Fixes: a5ed918285 ("Btrfs: implement the free space B-tree")
CC: <stable@vger.kernel.org> # 6.1.x: 1961d20f6f: btrfs: fix assertion when building free space tree
CC: <stable@vger.kernel.org> # 6.1.x
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
Syzbot reported an ASSERT() triggered inside scrub:
BTRFS info (device loop0): scrub: started on devid 1
assertion failed: !folio_test_partial_kmap(folio) :: 0, in fs/btrfs/scrub.c:697
------------[ cut here ]------------
kernel BUG at fs/btrfs/scrub.c:697!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 6077 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/18/2025
RIP: 0010:scrub_stripe_get_kaddr+0x1bb/0x1c0 fs/btrfs/scrub.c:697
Call Trace:
<TASK>
scrub_bio_add_sector fs/btrfs/scrub.c:932 [inline]
scrub_submit_initial_read+0xf21/0x1120 fs/btrfs/scrub.c:1897
submit_initial_group_read+0x423/0x5b0 fs/btrfs/scrub.c:1952
flush_scrub_stripes+0x18f/0x1150 fs/btrfs/scrub.c:1973
scrub_stripe+0xbea/0x2a30 fs/btrfs/scrub.c:2516
scrub_chunk+0x2a3/0x430 fs/btrfs/scrub.c:2575
scrub_enumerate_chunks+0xa70/0x1350 fs/btrfs/scrub.c:2839
btrfs_scrub_dev+0x6e7/0x10e0 fs/btrfs/scrub.c:3153
btrfs_ioctl_scrub+0x249/0x4b0 fs/btrfs/ioctl.c:3163
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
---[ end trace 0000000000000000 ]---
Which doesn't make much sense, as all the folios we allocated for scrub
should not be highmem.
[CAUSE]
Thankfully syzbot has a detailed kernel config file, showing that
CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP is set to y.
And that debug option will force all folio_test_partial_kmap() to return
true, to improve coverage on highmem tests.
But in our case we really just want to make sure the folios we allocated
are not highmem (and they are indeed not). Such incorrect result from
folio_test_partial_kmap() is just screwing up everything.
[FIX]
Replace folio_test_partial_kmap() to folio_test_highmem() so that we
won't bother those highmem specific debuging options.
Fixes: 5fbaae4b85 ("btrfs: prepare scrub to support bs > ps cases")
Reported-by: syzbot+bde59221318c592e6346@syzkaller.appspotmail.com
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
With v6.17-rc kernels, btrfs will always set 'ssd' mount option even if
the block device is not a rotating one:
# cat /sys/block/sdd/queue/rotational
1
# cat /etc/fstab:
LABEL=DATA2 /data2 btrfs rw,relatime,space_cache=v2,subvolid=5,subvol=/,nofail,nosuid,nodev 0 0
# mount
[...]
/dev/sdd on /data2 type btrfs (rw,nosuid,nodev,relatime,ssd,space_cache=v2,subvolid=5,subvol=/)
[CAUSE]
The 'ssd' mount option is set by set_device_specific_options(), and it
expects that if there is any rotating device in the btrfs, it will set
fs_devices::rotating.
However after commit bddf57a707 ("btrfs: delay btrfs_open_devices()
until super block is created"), the device opening is delayed until the
super block is created.
But the timing of set_device_specific_options() is still left as is,
this makes the function be called without any device opened.
Since no device is opened, thus fs_devices::rotating will never be set,
making btrfs incorrectly set 'ssd' mount option.
[FIX]
Only call set_device_specific_options() after btrfs_open_devices().
Also only call set_device_specific_options() after a new mount, if we're
mounting a mounted btrfs, there is no need to set the device specific
mount options again.
Reported-by: HAN Yuwei <hrx@bupt.moe>
Link: https://lore.kernel.org/linux-btrfs/C8FF75669DFFC3C5+5f93bf8a-80a0-48a6-81bf-4ec890abc99a@bupt.moe/
Fixes: bddf57a707 ("btrfs: delay btrfs_open_devices() until super block is created")
CC: stable@vger.kernel.org # 6.17
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
On 'btrfs_ioctl_qgroup_assign' we first duplicate the argument as
provided by the user, which is kfree'd in the end. But this was not the
case when allocating memory for 'prealloc'. In this case, if it somehow
failed, then the previous code would go directly into calling
'mnt_drop_write_file', without freeing the string duplicated from the
user space.
Fixes: 4addc1ffd6 ("btrfs: qgroup: preallocate memory before adding a relation")
CC: stable@vger.kernel.org # 6.12+
Reviewed-by: Boris Burkov <boris@bur.io>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Miquel Sabaté Solà <mssola@mssola.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When starting relocation, at reloc_chunk_start(), if we happen to find
the flag BTRFS_FS_RELOC_RUNNING is already set we return an error
(-EINPROGRESS) to the callers, however the callers call reloc_chunk_end()
which will clear the flag BTRFS_FS_RELOC_RUNNING, which is wrong since
relocation was started by another task and still running.
Finding the BTRFS_FS_RELOC_RUNNING flag already set is an unexpected
scenario, but still our current behaviour is not correct.
Fix this by never calling reloc_chunk_end() if reloc_chunk_start() has
returned an error, which is what logically makes sense, since the general
widespread pattern is to have end functions called only if the counterpart
start functions succeeded. This requires changing reloc_chunk_start() to
clear BTRFS_FS_RELOC_RUNNING if there's a pending cancel request.
Fixes: 907d2710d7 ("btrfs: add cancellable chunk relocation support")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Boris Burkov <boris@bur.io>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In normal operation, a registered exec queue is disabled and
deregistered through the GuC, and freed only after the GuC confirms
completion. However, if the driver is forced to unbind while the exec
queue is still running, the user may call exec_destroy() after the GuC
has already been stopped and CT communication disabled.
In this case, the driver cannot receive a response from the GuC,
preventing proper cleanup of exec queue resources. Fix this by directly
releasing the resources when GuC is not running.
Here is the failure dmesg log:
"
[ 468.089581] ---[ end trace 0000000000000000 ]---
[ 468.089608] pci 0000:03:00.0: [drm] *ERROR* GT0: GUC ID manager unclean (1/65535)
[ 468.090558] pci 0000:03:00.0: [drm] GT0: total 65535
[ 468.090562] pci 0000:03:00.0: [drm] GT0: used 1
[ 468.090564] pci 0000:03:00.0: [drm] GT0: range 1..1 (1)
[ 468.092716] ------------[ cut here ]------------
[ 468.092719] WARNING: CPU: 14 PID: 4775 at drivers/gpu/drm/xe/xe_ttm_vram_mgr.c:298 ttm_vram_mgr_fini+0xf8/0x130 [xe]
"
v2: use xe_uc_fw_is_running() instead of xe_guc_ct_enabled().
As CT may go down and come back during VF migration.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org
Cc: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20251010172529.2967639-2-shuicheng.lin@intel.com
(cherry picked from commit 9b42321a02)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Moving to VRAM will fail if mixed mappings are present or if the page is
already located in VRAM. Atomic faults that require a move to VRAM
currently retry without attempting to evict mixed mappings or locate
existing VRAM mappings.
This patch fixes the issue by attempting to evict mixed mappings or find
existing VRAM pages when a move to VRAM fails during atomic fault
handling.
Fixes: a9ac0fa455 ("drm/xe: Strict migration policy for atomic SVM faults")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://lore.kernel.org/r/20251009130629.3531962-1-matthew.brost@intel.com
(cherry picked from commit 75188605c5)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
There may be cases in which the BAR0 also needs to move to accommodate
the bigger BAR2. However if it's not released, the BAR2 resize fails.
During the vram probe it can't be released as it's already in use by
xe_mmio for early register access.
Add a new function in xe_vram and let xe_pci call it directly before
even early device probe. This allows the BAR2 to resize in cases BAR0
also needs to move, assuming there aren't other reasons to hold that
move:
[] xe 0000:03:00.0: vgaarb: deactivate vga console
[] xe 0000:03:00.0: [drm] Attempting to resize bar from 8192MiB -> 16384MiB
[] xe 0000:03:00.0: BAR 0 [mem 0x83000000-0x83ffffff 64bit]: releasing
[] xe 0000:03:00.0: BAR 2 [mem 0x4000000000-0x41ffffffff 64bit pref]: releasing
[] pcieport 0000:02:01.0: bridge window [mem 0x4000000000-0x41ffffffff 64bit pref]: releasing
[] pcieport 0000:01:00.0: bridge window [mem 0x4000000000-0x41ffffffff 64bit pref]: releasing
[] pcieport 0000:01:00.0: bridge window [mem 0x4000000000-0x43ffffffff 64bit pref]: assigned
[] pcieport 0000:02:01.0: bridge window [mem 0x4000000000-0x43ffffffff 64bit pref]: assigned
[] xe 0000:03:00.0: BAR 2 [mem 0x4000000000-0x43ffffffff 64bit pref]: assigned
[] xe 0000:03:00.0: BAR 0 [mem 0x83000000-0x83ffffff 64bit]: assigned
[] pcieport 0000:00:01.0: PCI bridge to [bus 01-04]
[] pcieport 0000:00:01.0: bridge window [mem 0x83000000-0x840fffff]
[] pcieport 0000:00:01.0: bridge window [mem 0x4000000000-0x44007fffff 64bit pref]
[] pcieport 0000:01:00.0: PCI bridge to [bus 02-04]
[] pcieport 0000:01:00.0: bridge window [mem 0x83000000-0x840fffff]
[] pcieport 0000:01:00.0: bridge window [mem 0x4000000000-0x43ffffffff 64bit pref]
[] pcieport 0000:02:01.0: PCI bridge to [bus 03]
[] pcieport 0000:02:01.0: bridge window [mem 0x83000000-0x83ffffff]
[] pcieport 0000:02:01.0: bridge window [mem 0x4000000000-0x43ffffffff 64bit pref]
[] xe 0000:03:00.0: [drm] BAR2 resized to 16384M
[] xe 0000:03:00.0: [drm:xe_pci_probe [xe]] BATTLEMAGE e221:0000 dgfx:1 gfx:Xe2_HPG (20.02) ...
For BMG there are additional fix needed in the PCI side, but this
helps getting it to a working resize.
All the rebar logic is more pci-specific than xe-specific and can be
done very early in the probe sequence. In future it would be good to
move it out of xe_vram.c, but this refactor is left for later.
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: stable@vger.kernel.org # 6.12+
Link: https://lore.kernel.org/intel-xe/fafda2a3-fc63-ce97-d22b-803f771a4d19@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20250918-xe-pci-rebar-2-v1-2-6c094702a074@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 45e33f220f)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently NETDEV_UNREGISTER event handler is not calling
j1939_cancel_active_session() and j1939_sk_queue_drop_all().
This will result in these calls being skipped when j1939_sk_release() is
called. And I guess that the reason syzbot is still reporting
unregister_netdevice: waiting for vcan0 to become free. Usage count = 2
is caused by lack of these calls.
Calling j1939_cancel_active_session(priv, sk) from j1939_sk_release() can
be covered by calling j1939_cancel_active_session(priv, NULL) from
j1939_netdev_notify().
Calling j1939_sk_queue_drop_all() from j1939_sk_release() can be covered
by calling j1939_sk_netdev_event_netdown() from j1939_netdev_notify().
Therefore, we can reuse j1939_cancel_active_session(priv, NULL) and
j1939_sk_netdev_event_netdown(priv) for NETDEV_UNREGISTER event handler.
Fixes: 7fcbe5b2c6 ("can: j1939: implement NETDEV_UNREGISTER notification handler")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/3ad3c7f8-5a74-4b07-a193-cb0725823558@I-love.SAKURA.ne.jp
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Vincent Mailhol <mailhol@kernel.org> says:
TDC was added to the kernel in 2021 but I never took time to update the
documentation. The year is now 2025... As we say: "better late than never"!
The first patch is a small clean up which fixes an incorrect statement
concerning the CAN DLC, the second patch is the real thing and adds the
documentation of how to use the ip tool to configure the TDC.
Link: https://patch.msgid.link/20251013-can-fd-doc-v2-0-5d53bdc8f2ad@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN-FD section of can.rst still states that there is a 1:1 mapping
between the Classical CAN DLC and its length. This is only true for
the DLC values up to 8. Beyond that point, the length remains at 8.
For reference, the mapping between the CAN DLC and the length is given
in below table [1]:
DLC value CBFF and CEFF FBFF and FEFF
[decimal] [byte] [byte]
----------------------------------------------
0 0 0
1 1 1
2 2 2
3 3 3
4 4 4
5 5 5
6 6 6
7 7 7
8 8 8
9 8 12
10 8 16
11 8 20
12 8 24
13 8 32
14 8 48
15 8 64
Remove the erroneous statement. Instead just state that the length of
a Classical CAN frame ranges from 0 to 8.
[1] ISO 11898-1:2024, Table 5 -- DLC: coding of the four LSB
Signed-off-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20251013-can-fd-doc-v2-1-5d53bdc8f2ad@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Users can create as many monitoring groups as the number of RMIDs supported
by the hardware. However, on AMD systems, only a limited number of RMIDs
are guaranteed to be actively tracked by the hardware. RMIDs that exceed
this limit are placed in an "Unavailable" state.
When a bandwidth counter is read for such an RMID, the hardware sets
MSR_IA32_QM_CTR.Unavailable (bit 62). When such an RMID starts being tracked
again the hardware counter is reset to zero. MSR_IA32_QM_CTR.Unavailable
remains set on first read after tracking re-starts and is clear on all
subsequent reads as long as the RMID is tracked.
resctrl miscounts the bandwidth events after an RMID transitions from the
"Unavailable" state back to being tracked. This happens because when the
hardware starts counting again after resetting the counter to zero, resctrl
in turn compares the new count against the counter value stored from the
previous time the RMID was tracked.
This results in resctrl computing an event value that is either undercounting
(when new counter is more than stored counter) or a mistaken overflow (when
new counter is less than stored counter).
Reset the stored value (arch_mbm_state::prev_msr) of MSR_IA32_QM_CTR to
zero whenever the RMID is in the "Unavailable" state to ensure accurate
counting after the RMID resets to zero when it starts to be tracked again.
Example scenario that results in mistaken overflow
==================================================
1. The resctrl filesystem is mounted, and a task is assigned to a
monitoring group.
$mount -t resctrl resctrl /sys/fs/resctrl
$mkdir /sys/fs/resctrl/mon_groups/test1/
$echo 1234 > /sys/fs/resctrl/mon_groups/test1/tasks
$cat /sys/fs/resctrl/mon_groups/test1/mon_data/mon_L3_*/mbm_total_bytes
21323 <- Total bytes on domain 0
"Unavailable" <- Total bytes on domain 1
Task is running on domain 0. Counter on domain 1 is "Unavailable".
2. The task runs on domain 0 for a while and then moves to domain 1. The
counter starts incrementing on domain 1.
$cat /sys/fs/resctrl/mon_groups/test1/mon_data/mon_L3_*/mbm_total_bytes
7345357 <- Total bytes on domain 0
4545 <- Total bytes on domain 1
3. At some point, the RMID in domain 0 transitions to the "Unavailable"
state because the task is no longer executing in that domain.
$cat /sys/fs/resctrl/mon_groups/test1/mon_data/mon_L3_*/mbm_total_bytes
"Unavailable" <- Total bytes on domain 0
434341 <- Total bytes on domain 1
4. Since the task continues to migrate between domains, it may eventually
return to domain 0.
$cat /sys/fs/resctrl/mon_groups/test1/mon_data/mon_L3_*/mbm_total_bytes
17592178699059 <- Overflow on domain 0
3232332 <- Total bytes on domain 1
In this case, the RMID on domain 0 transitions from "Unavailable" state to
active state. The hardware sets MSR_IA32_QM_CTR.Unavailable (bit 62) when
the counter is read and begins tracking the RMID counting from 0.
Subsequent reads succeed but return a value smaller than the previously
saved MSR value (7345357). Consequently, the resctrl's overflow logic is
triggered, it compares the previous value (7345357) with the new, smaller
value and incorrectly interprets this as a counter overflow, adding a large
delta.
In reality, this is a false positive: the counter did not overflow but was
simply reset when the RMID transitioned from "Unavailable" back to active
state.
Here is the text from APM [1] available from [2].
"In PQOS Version 2.0 or higher, the MBM hardware will set the U bit on the
first QM_CTR read when it begins tracking an RMID that it was not
previously tracking. The U bit will be zero for all subsequent reads from
that RMID while it is still tracked by the hardware. Therefore, a QM_CTR
read with the U bit set when that RMID is in use by a processor can be
considered 0 when calculating the difference with a subsequent read."
[1] AMD64 Architecture Programmer's Manual Volume 2: System Programming
Publication # 24593 Revision 3.41 section 19.3.3 Monitoring L3 Memory
Bandwidth (MBM).
[ bp: Split commit message into smaller paragraph chunks for better
consumption. ]
Fixes: 4d05bf71f1 ("x86/resctrl: Introduce AMD QOS feature")
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org # needs adjustments for <= v6.17
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537 # [2]
port->nr_dports is used to represent how many dports added to the cxl
port, it will increase in add_dport() when a new dport is being added to
the cxl port, but it will not be reduced when a dport is removed from
the cxl port.
Currently, when the first dport is added to a cxl port, it will trigger
component registers setup on the cxl port, the implementation is using
port->nr_dports to confirm if the dport is the first dport.
A corner case here is that adding dport could fail after port->nr_dports
updating and before checking port->nr_dports for component registers
setup. If the failure happens during the first dport attaching, it will
cause that CXL subsystem has not chance to execute component registers
setup for the cxl port. the failure flow like below:
port->nr_dports = 0
dport 1 adding to the port:
add_dport() # port->nr_dports: 1
failed on devm_add_action_or_reset() or sysfs_create_link()
return error # port->nr_dports: 1
dport 2 adding to the port:
add_dport() # port->nr_dports: 2
no failure
skip component registers setup because of port->nr_dports is 2
The solution here is that moving component registers setup closer to
add_dport(), so if add_dport() is executed correctly for the first
dport, component registers setup on the port will be executed
immediately after that.
Fixes: f6ee24913d ("cxl: Move port register setup to when first dport appear")
Signed-off-by: Li Ming <ming.li@zohomail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Since the last renewal time was initialized to 0 and jiffies start
counting at -5 minutes, any clients connected in the first 5 minutes
after a reboot would have their renewal timer set to a very long
interval. If the connection was idle, this would result in the client
state timing out on the server and the next call to the server would
return NFS4ERR_BADSESSION.
Fix this by initializing the last renewal time to the current jiffies
instead of 0.
Signed-off-by: Joshua Watt <jpewhacker@gmail.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
I noticed xfstests generic/193 and generic/355 started failing against
knfsd after commit e7a8ebc305 ("NFSD: Offer write delegation for OPEN
with OPEN4_SHARE_ACCESS_WRITE").
I ran those same tests against ONTAP (which has had write delegation
support for a lot longer than knfsd) and they fail there too... so
while it's a new failure against knfsd, it isn't an entirely new
failure.
Add the NFS_INO_REVAL_FORCED flag so that the presence of a delegation
doesn't keep the inode from being revalidated to fetch the updated mode.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
The setting of delay_retrans is applied to synchronous RPC operations
because the retransmit count is stored in same struct nfs4_exception
that is passed each time an error is checked. However, for asynchronous
operations (READ, WRITE, LOCKU, CLOSE, DELEGRETURN), a new struct
nfs4_exception is made on the stack each time the task callback is
invoked. This means that the retransmit count is always zero and thus
delay_retrans never takes effect.
Apply delay_retrans to these operations by tracking and updating their
retransmit count.
Change-Id: Ieb33e046c2b277cb979caa3faca7f52faf0568c9
Signed-off-by: Joshua Watt <jpewhacker@gmail.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Move mirror_array's dss_count initialization and dss allocation to
ff_layout_alloc_mirror(), just before the loop that initializes each
nfs4_ff_layout_ds_stripe's nfs_file_localio.
Also handle NULL return from kcalloc() and remove one level of indent
in ff_layout_alloc_mirror().
This commit fixes dangling nfsd_serv refcount issues seen when using
NFS LOCALIO and then attempting to stop the NFSD service.
Fixes: 20b1d75fb8 ("NFSv4/flexfiles: Add support for striped layouts")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
This reverts commit 90bfb28d5f.
Kevin reports that this commit causes an issue for him with LVM
snapshots, most likely because of turning off NOWAIT support while a
snapshot is being created. This makes -EOPNOTSUPP bubble back through
the completion handler, where io_uring read/write handling should just
retry it.
Reinstate the previous check removed by the referenced commit.
Cc: stable@vger.kernel.org
Fixes: 90bfb28d5f ("io_uring/rw: drop -EOPNOTSUPP check in __io_complete_rw_common()")
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Reported-by: Kevin Lumik <kevin@xf.ee>
Link: https://lore.kernel.org/io-uring/cceb723c-051b-4de2-9a4c-4aa82e1619ee@kernel.dk/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By design the MES will return an array result that is twice the number
of hung doorbells it can report.
i.e. if up k reported doorbells are supported, then the
second half of the array, also of length k, holds the HQD information
(type/queue/pipe) where queue 1 corresponds to index 0 and k,
queue 2 corresponds to index 1 and k + 1 etc ...
The driver will use the HDQ info to target queue/pipe reset for
hardware scheduled user compute queues.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initialized doorbells should be set to invalid rather than 0 to prevent
driver from over counting hung doorbells since it checks against the
invalid value to begin with.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX12 MES uses low 32 bits of status return for success (1 or 0)
and high bits for debug information if low bits are 0.
GFX11 MES doesn't do this so checking full 64-bit status return
for 1 or 0 is still valid.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Previously, APU platforms (and other scenarios with uninitialized VRAM managers)
triggered a NULL pointer dereference in `ttm_resource_manager_usage()`. The root
cause is not that the `struct ttm_resource_manager *man` pointer itself is NULL,
but that `man->bdev` (the backing device pointer within the manager) remains
uninitialized (NULL) on APUs—since APUs lack dedicated VRAM and do not fully
set up VRAM manager structures. When `ttm_resource_manager_usage()` attempts to
acquire `man->bdev->lru_lock`, it dereferences the NULL `man->bdev`, leading to
a kernel OOPS.
1. **amdgpu_cs.c**: Extend the existing bandwidth control check in
`amdgpu_cs_get_threshold_for_moves()` to include a check for
`ttm_resource_manager_used()`. If the manager is not used (uninitialized
`bdev`), return 0 for migration thresholds immediately—skipping VRAM-specific
logic that would trigger the NULL dereference.
2. **amdgpu_kms.c**: Update the `AMDGPU_INFO_VRAM_USAGE` ioctl and memory info
reporting to use a conditional: if the manager is used, return the real VRAM
usage; otherwise, return 0. This avoids accessing `man->bdev` when it is
NULL.
3. **amdgpu_virt.c**: Modify the vf2pf (virtual function to physical function)
data write path. Use `ttm_resource_manager_used()` to check validity: if the
manager is usable, calculate `fb_usage` from VRAM usage; otherwise, set
`fb_usage` to 0 (APUs have no discrete framebuffer to report).
This approach is more robust than APU-specific checks because it:
- Works for all scenarios where the VRAM manager is uninitialized (not just APUs),
- Aligns with TTM's design by using its native helper function,
- Preserves correct behavior for discrete GPUs (which have fully initialized
`man->bdev` and pass the `ttm_resource_manager_used()` check).
v4: use ttm_resource_manager_used(&adev->mman.vram_mgr.manager) instead of checking the adev->gmc.is_app_apu flag (Christian)
Reviewed-by: Christian König <christian.koenig@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove extra multiplication.
CIK GPUs such as Hawaii appear to use PP_TABLE_V0 in which case
the shutdown temperature is hardcoded in smu7_init_dpm_defaults
and is already multiplied by 1000. The value was mistakenly
multiplied another time by smu7_get_thermal_temperature_range.
Fixes: 4ba082572a ("drm/amd/powerplay: export the thermal ranges of VI asics (V2)")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1676
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These were never used and are duplicated with the
interface that is used. Maybe leftovers from a previous
revision of the patch that added them.
Fixes: 90c448fef3 ("drm/amdgpu: add new AMDGPU_INFO subquery for userq objects")
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The atomic variable vm_fault_info_updated is used to synchronize access to
adev->gmc.vm_fault_info between the interrupt handler and
get_vm_fault_info().
The default atomic functions like atomic_set() and atomic_read() do not
provide memory barriers. This allows for CPU instruction reordering,
meaning the memory accesses to vm_fault_info and the vm_fault_info_updated
flag are not guaranteed to occur in the intended order. This creates a
race condition that can lead to inconsistent or stale data being used.
The previous implementation, which used an explicit mb(), was incomplete
and inefficient. It failed to account for all potential CPU reorderings,
such as the access of vm_fault_info being reordered before the atomic_read
of the flag. This approach is also more verbose and less performant than
using the proper atomic functions with acquire/release semantics.
Fix this by switching to atomic_set_release() and atomic_read_acquire().
These functions provide the necessary acquire and release semantics,
which act as memory barriers to ensure the correct order of operations.
It is also more efficient and idiomatic than using explicit full memory
barriers.
Fixes: b97dfa27ef ("drm/amdgpu: save vm fault information for amdkfd")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we backup ring contents to reemit after a queue reset,
we don't backup ring contents from the bad context. When
we signal the fences, we should set an error on those
fences as well.
v2: misc cleanups
v3: add locking for fence error, fix comment (Christian)
v4: fix wrap around, locking (Christian)
Fixes: 77cc0da39c ("drm/amdgpu: track ring state associated with a fence")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chips which use the IP discovery firmware loaded by the driver
reported incorrect harvesting information in the ip discovery
table in sysfs because the driver only uses the ip discovery
firmware for populating sysfs and not for direct parsing for the
driver itself as such, the fields that are used to print the
harvesting info in sysfs report incorrect data for some IPs. Populate
the relevant fields for this case as well.
Fixes: 514678da56 ("drm/amdgpu/discovery: fix fw based ip discovery")
Acked-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Constant Engine found on gfx6-gfx10 HW has been a notorious source of
problems.
RADV never used it in the first place, radeonsi only used it for a few
releases around 2017 for gfx6-gfx9 before dropping support for it as
well.
While investigating another problem I just recently found that submitting
to the CE seems to be completely broken on gfx9 for quite a while.
Since nobody complained about that problem it most likely means that
nobody is using any of the affected radeonsi versions on current Linux
kernels any more.
So to potentially phase out the support for the CE and eliminate another
source of problems block submitting CE IBs unless it is enabled again
using a debug flag.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enabling ASPM causes randoms hangs on Tahiti and Oland on Zen4.
It's unclear if this is a platform-specific or GPU-specific issue.
Disable ASPM on SI for the time being.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On various SI GPUs, a flickering can be observed near the bottom
edge of the screen when using a single 4K 60Hz monitor over DP.
Disabling MCLK switching works around this problem.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
intel_frontbuffer_get() is what locks out subsequent set_tiling
changes to the bo. Thus the fence vs. modifier check must be done
after intel_frontbuffer_get(), or else a concurrent set_tiling ioctl
might sneak in and change the fence after the check has been done.
Close the race again. See commit dd689287b9 ("drm/i915: Prevent
concurrent tiling/framebuffer modifications") for the previous
instance.
v2: Reorder intel_user_framebuffer_destroy() to match the unwind (Jani)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-3-ville.syrjala@linux.intel.com
(cherry picked from commit 1d1e4ded21)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently xe's intel_frontbuffer implementation forgets to
hold a reference on the bo. This makes the entire thing
extremely fragile as the cleanup order now depends on bo
references held by other things
(namely intel_fb_bo_framebuffer_fini()).
Move the bo refcounting to intel_frontbuffer_{get,release}()
so that both i915 and xe do this the same way.
I first tried to fix this by having xe do the refcounting
from its intel_bo_set_frontbuffer() implementation
(which is what i915 does currently), but turns out xe's
drm_gem_object_free() can sleep and thus drm_gem_object_put()
isn't safe to call while we hold fb_tracking.lock.
Fixes: 10690b8a49 ("drm/i915/display: Add intel_fb_bo_framebuffer_fini")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20251003145734.7634-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eb4d490729)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Marc reports that the performance of running an L3 guest has regressed
by 60% as a result of setting MDCR_EL2.TDA to hide bad architecture.
That's of course terrible for the single user of recursive NV ;-)
While there's nothing to be done on non-FGT systems, take advantage of
the precise write trap of MDSCR_EL1 and leave the rest of the debug
registers untrapped.
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
To date KVM has used the fine-grained traps for the sake of UNDEF
enforcement (so-called FGUs), meaning the constituent parts could be
computed on a per-VM basis and folded into the effective value when
programmed.
Prepare for traps changing based on the vCPU context by computing the
whole mess of them at vcpu_load(). Aggressively inline all the helpers
to preserve the build-time checks that were there before.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The userspace-visible encoding for CNTV_CVAL_EL0 and CNTVCNT_EL0
have been swapped for as long as usersapce has had access to the
registers. This is documented in arch/arm64/include/uapi/asm/kvm.h.
Despite that, the get_reg_list test has unhelpful comments indicating
the wrong register for the encoding.
Replace this with definitions exposed in the include file, and
a comment explaining again the brokenness.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The hyp virtual timer registers only exist when VHE is present,
Similarly, VNCR_EL2 only exists when NV2 is present.
Make these dependencies explicit.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that the whole timer infrastructure is handled as system register
accesses, get rid of the now unused ad-hoc infrastructure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The spec for WFxT indicates that the parameter to the WFxT instruction
is relative to the reading of CNTVCT_EL0. This means that the implementation
needs to take the execution context into account, as CNTVOFF_EL2
does not always affect readings of CNTVCT_EL0 (such as when HCR_EL2.E2H
is 1 and that we're in host context).
This also rids us of the last instance of KVM_REG_ARM_TIMER_CNT
outside of the userspace interaction code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Moving the counter registers is a bit more involved than for the control
and comparator (there is no shadow data for the counter), but still
pretty manageable.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Remove the handling of CNT*_CTL_EL0 from guest.c, and move it to
sys_regs.c, using a new TIMER_REG() definition to encapsulate it.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Amongst the numerous bugs that plague the KVM/arm64 UAPI, one of
the most annoying thing is that the userspace view of the virtual
timer has its CVAL and CNT encodings swapped.
In order to reduce the amount of code that has to know about this,
start by adding handling for this bug in the sys_reg code.
Nothing is making use of it yet, as the code responsible for userspace
interaction is catching the accesses early.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Move the timer_set_offset() helper to arm_arch_timer.h, so that it
is next to timer_get_offset(), and accessible by the rest of KVM.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Having to follow a pointer to a vcpu is pretty dumb, when the timers
are are a fixed offset in the vcpu structure itself.
Trade the vcpu pointer for a timer_id, which can then be used to
compute the vcpu address as needed.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We currently have a vcpu pointer nested into each timer context.
As we are about to remove this pointer, introduce a helper (aptly
named timer_context_to_vcpu()) that returns this pointer, at least
until we repaint the data structure.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Although we correctly UNDEF any CNTHV_*_EL2 access from the guest
when E2H==0, we still expose these registers to userspace, which
is a bad idea.
Drop the ad-hoc UNDEF injection and switch to a .visibility()
callback which will also hide the register from userspace.
Fixes: 0e45981028 ("KVM: arm64: timer: Don't adjust the EL2 virtual timer offset")
Signed-off-by: Marc Zyngier <maz@kernel.org>
GICv5 hosts optionally include FEAT_GCIE_LEGACY, which allows them to
execute GICv3-based VMs on GICv5 hardware. Update the GICv3
documentation to reflect this now that GICv3 guests are supports on
compatible GICv5 hosts.
Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The ICH_HCR_EL2 traps are used when running on GICv3 hardware, or when
running a GICv3-based guest using FEAT_GCIE_LEGACY on GICv5
hardware. When running a GICv2 guest on GICv3 hardware the traps are
used to ensure that the guest never sees any part of GICv3 (only GICv2
is visible to the guest), and when running a GICv3 guest they are used
to trap in specific scenarios. They are not applicable for a
GICv2-native guest, and won't be applicable for a(n upcoming) GICv5
guest.
The traps themselves are configured in the vGIC CPU IF state, which is
stored as a union. Updating the wrong aperture of the union risks
corrupting state, and therefore needs to be avoided at all costs.
Bail early if we're not running a compatible guest (GICv2 on GICv3
hardware, GICv3 native, GICv3 on GICv5 hardware). Trap everything
unconditionally if we're running a GICv2 guest on GICv3
hardware. Otherwise, conditionally set up GICv3-native trapping.
Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
vgic_lpi_stress rather hilariously leaves IRQs disabled for the duration
of the test. While the ITS translation of MSIs happens regardless of
this, for completeness the guest should actually handle the LPIs.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Zenghui Yu <zenghui.yu@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
vcpus array contains pointers to struct kvm_vcpu {}. It is way overkill
to allocate the array with (nr_cpus * sizeof(struct kvm_vcpu)). Fix the
allocation by using the correct size.
Signed-off-by: Zenghui Yu <zenghui.yu@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Commit efad60e460 ("KVM: arm64: Initialize PMSCR_EL1 when in VHE")
does not perform sufficient check before initializing PMSCR_EL1 to 0
when running in VHE mode. On some platforms, this causes the system to
hang during boot, as EL3 has not delegated access to the Profiling
Buffer to the Non-secure world, nor does it reinject an UNDEF on sysreg
trap.
To avoid this issue, restrict the PMSCR_EL1 initialization to CPUs that
support Statistical Profiling Extension (FEAT_SPE) and have the
Profiling Buffer accessible in Non-secure EL1. This is determined via a
new helper `cpu_has_spe()` which checks both PMSVer and PMBIDR_EL1.P.
This ensures the initialization only affects CPUs where SPE is
implemented and usable, preventing boot failures on platforms where SPE
is not properly configured.
Fixes: efad60e460 ("KVM: arm64: Initialize PMSCR_EL1 when in VHE")
Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The local variable “rc” is assigned a value in an if branch without
using it before it is reassigned there.
Thus delete this assignment statement.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Steve French <stfrench@microsoft.com>
Return a status code without storing it in an intermediate variable.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Steve French <stfrench@microsoft.com>
We forgot to sync several registers (ID_AA64PFR1, MPIDR, CLIDR) in guest to
make sure that the guest had seen the written value.
Add them to the list.
Signed-off-by: Zenghui Yu <zenghui.yu@linux.dev>
Reviewed-By: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Remove an unnecessary 'break' statement that follows a 'return'
in arch/arm64/kvm/at.c. The break is unreachable.
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The KVM_IRQFD ioctl fails if no irqchip is present in-kernel, which
isn't too surprising as there's not much KVM can do for an IRQ if it
cannot resolve a destination.
As written the irqfd_test assumes that a 'default' VM created in
selftests has an in-kernel irqchip created implicitly. That may be the
case on x86 but it isn't necessarily true on other architectures.
Add an arch predicate indicating if 'default' VMs get an irqchip and
make the irqfd_test depend on it. Work around arm64 VGIC initialization
requirements by using vm_create_with_one_vcpu(), ignoring the created
vCPU as it isn't used for the test.
Reported-by: Sebastian Ott <sebott@redhat.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Sean Christopherson <seanjc@google.com>
Fixes: 7e9b231c40 ("KVM: selftests: Add a KVM_IRQFD test to verify uniqueness requirements")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
KVM rejects calls to KVM_{GET,SET}_VCPU_EVENTS for an uninitialized vCPU
as of commit cc96679f3c03 ("KVM: arm64: Prevent access to vCPU events
before init"). Update the corresponding API documentation.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Another day, another syzkaller bug. KVM erroneously allows userspace to
pend vCPU events for a vCPU that hasn't been initialized yet, leading to
KVM interpreting a bunch of uninitialized garbage for routing /
injecting the exception.
In one case the injection code and the hyp disagree on whether the vCPU
has a 32bit EL1 and put the vCPU into an illegal mode for AArch64,
tripping the BUG() in exception_target_el() during the next injection:
kernel BUG at arch/arm64/kvm/inject_fault.c:40!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
CPU: 3 UID: 0 PID: 318 Comm: repro Not tainted 6.17.0-rc4-00104-g10fd0285305d #6 PREEMPT
Hardware name: linux,dummy-virt (DT)
pstate: 21402009 (nzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : exception_target_el+0x88/0x8c
lr : pend_serror_exception+0x18/0x13c
sp : ffff800082f03a10
x29: ffff800082f03a10 x28: ffff0000cb132280 x27: 0000000000000000
x26: 0000000000000000 x25: ffff0000c2a99c20 x24: 0000000000000000
x23: 0000000000008000 x22: 0000000000000002 x21: 0000000000000004
x20: 0000000000008000 x19: ffff0000c2a99c20 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 00000000200000c0
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffff800082f03af8 x7 : 0000000000000000 x6 : 0000000000000000
x5 : ffff800080f621f0 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 000000000040009b x1 : 0000000000000003 x0 : ffff0000c2a99c20
Call trace:
exception_target_el+0x88/0x8c (P)
kvm_inject_serror_esr+0x40/0x3b4
__kvm_arm_vcpu_set_events+0xf0/0x100
kvm_arch_vcpu_ioctl+0x180/0x9d4
kvm_vcpu_ioctl+0x60c/0x9f4
__arm64_sys_ioctl+0xac/0x104
invoke_syscall+0x48/0x110
el0_svc_common.constprop.0+0x40/0xe0
do_el0_svc+0x1c/0x28
el0_svc+0x34/0xf0
el0t_64_sync_handler+0xa0/0xe4
el0t_64_sync+0x198/0x19c
Code: f946bc01 b4fffe61 9101e020 17fffff2 (d4210000)
Reject the ioctls outright as no sane VMM would call these before
KVM_ARM_VCPU_INIT anyway. Even if it did the exception would've been
thrown away by the eventual reset of the vCPU's state.
Cc: stable@vger.kernel.org # 6.17
Fixes: b7b27facc7 ("arm/arm64: KVM: Add KVM_GET/SET_VCPU_EVENTS")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Store the width of arm64's timer counter as an "int", not a "uint64_t".
ilog2() returns an "int", and more importantly using what is an "unsigned
long" under the hood makes clang unhappy due to a type mismatch when
clamping the width to a sane value.
arm64/arch_timer_edge_cases.c:1032:10: error: comparison of distinct pointer types
('typeof (width) *' (aka 'unsigned long *') and 'typeof (56) *' (aka 'int *'))
[-Werror,-Wcompare-distinct-pointer-types]
1032 | width = clamp(width, 56, 64);
| ^~~~~~~~~~~~~~~~~~~~
tools/include/linux/kernel.h:47:45: note: expanded from macro 'clamp'
47 | #define clamp(val, lo, hi) min((typeof(val))max(val, lo), hi)
| ^~~~~~~~~~~~
tools/include/linux/kernel.h:33:17: note: expanded from macro 'max'
33 | (void) (&_max1 == &_max2); \
| ~~~~~~ ^ ~~~~~~
tools/include/linux/kernel.h:39:9: note: expanded from macro 'min'
39 | typeof(x) _min1 = (x); \
| ^
Fixes: fad4cf9448 ("KVM: arm64: selftests: Determine effective counter width in arch_timer_edge_cases")
Cc: Sebastian Ott <sebott@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
A defect against the architecture now allows an implementation to treat
AMO as 1 when HCR_EL2.{E2H, TGE} = {1, 0}. KVM now takes advantage of
this interpretation to address a quality of emulation issue w.r.t.
SError injection.
Add a corresponding test case and expect a pending SError to be taken.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Running the external_aborts selftest at EL2 leads to an ugly splat due
to the stage-1 MMU being disabled for the walked context, owing to the
fact that __kvm_find_s1_desc_level() is hardcoded to the EL1&0 regime.
Select the appropriate translation regime for the stage-1 walk based on
the current vCPU context.
Fixes: b8e625167a ("KVM: arm64: Add S1 IPA to page table level walker")
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Jan reports that running a nested guest on Neoverse-V2 leads to a WARN
in the host due to simultaneously pending an exception and PC increment
after an access to ZCR_EL2.
Returning true from a sysreg accessor is an indication that the sysreg
instruction has been retired. Of course this isn't the case when we've
pended a synchronous SVE exception for the guest. Fix the return value
and let the exception propagate to the guest as usual.
Reported-by: Jan Kotas <jank@cadence.com>
Closes: https://lore.kernel.org/kvmarm/865xd61tt5.wl-maz@kernel.org/
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Unlike the other mapped EL2 sysregs ZCR_EL2 isn't guaranteed to be
resident when a vCPU is loaded as it actually follows the SVE
context. As such, the contents of ZCR_EL1 may belong to another guest if
the vCPU has been preempted before reaching sysreg emulation.
Unconditionally use the in-memory value of ZCR_EL2 and switch to the
memory-only accessors. The in-memory value is guaranteed to be valid as
fpsimd_lazy_switch_to_{guest,host}() will restore/save the register
appropriately.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In csqspi_probe(), when cqspi_request_mmap_dma() returns -EPROBE_DEFER,
we handle the error by jumping to probe_setup_failed.
In that label, we call pm_runtime_disable(), even if we never called
pm_runtime_enable() before.
Because of this, the driver cannot probe:
[ 2.690018] cadence-qspi 47040000.spi: No Rx DMA available
[ 2.699735] spi-nor spi0.0: resume failed with -13
[ 2.699741] spi-nor: probe of spi0.0 failed with error -13
Only call pm_runtime_disable() if it was enabled by adding a new
label to handle cqspi_request_mmap_dma() failures.
Fixes: b07f349d18 ("spi: spi-cadence-quadspi: Fix pm runtime unbalance")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20251009-cadence-quadspi-fix-pm-runtime-v2-1-8bdfefc43902@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For different sample clock source selection, the max frequency
flexspi supported are different. For mode 0, max frequency is 66MHz.
For mode 3, the max frequency is 166MHz.
Refer to 3.9.9 FlexSPI timing parameters on page 65.
https://www.nxp.com/docs/en/data-sheet/IMX8MNCEC.pdf
Though flexspi maybe still work under higher frequency, but can't
guarantee the stability. IC suggest to add this limitation on all
SoCs which contain flexspi.
Fixes: c07f270323 ("spi: spi-nxp-fspi: add the support for sample data from DQS pad")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://patch.msgid.link/20250922-fspi-fix-v1-3-ff4315359d31@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handler offloads the microphone detection logic to
nau8821_jdet_work(), which implies a sleep operation. However, before
being able to process any subsequent hotplug event, the interrupt
handler needs to wait for any prior scheduled work to complete.
Move the sleep out of jdet_work by converting it to a delayed work.
This eliminates the undesired blocking in the interrupt handler when
attempting to cancel a recently scheduled work item and should help
reducing transient input reports that might confuse user-space.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-5-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stress testing the audio jack hotplug handling on a few Steam Deck units
revealed that the debounce circuit is responsible for having a negative
impact on the detection reliability, e.g. in some cases the ejection
interrupt is not fired, while in other instances it goes into a kind of
invalid state and generates a flood of misleading interrupts.
Add new entries to the DMI table introduced via commit 1bc40efdaf
("ASoC: nau8821: Add DMI quirk mechanism for active-high jack-detect")
and extend the quirk logic to allow bypassing the debounce circuit used
for jack detection on Valve Steam Deck LCD and OLED models.
While at it, rename existing NAU8821_JD_ACTIVE_HIGH quirk bitfield to
NAU8821_QUIRK_JD_ACTIVE_HIGH. This should help improve code readability
by differentiating from similarly named register bits.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-4-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handler attempts to perform some IRQ status clear
operations *after* rather than *before* unmasking and enabling
interrupts. This is a rather fragile approach since it may generally
lead to missing IRQ requests or causing spurious interrupts.
Make use of the nau8821_irq_status_clear() helper instead of
manipulating the related register directly and ensure any interrupt
clearing is performed *after* the target interrupts are disabled/masked
and *before* proceeding with additional interrupt unmasking/enablement
operations.
This also implicitly drops the redundant clear operation of the ejection
IRQ in the interrupt handler, since nau8821_eject_jack() has been
already responsible for clearing all active interrupts.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Fixes: 2551b6e899 ("ASoC: nau8821: Add headset button detection")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-3-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of adding yet another utility function for dealing with the
interrupt clearing register, generalize nau8821_int_status_clear_all()
by renaming it to nau8821_irq_status_clear(), whilst introducing a
second parameter to allow restricting the operation scope to a single
interrupt instead of the whole range of active IRQs.
While at it, also fix a spelling typo in the comment block.
Note this is mainly a prerequisite for subsequent patches aiming to
address some deficiencies in the implementation of the interrupt
handler. Thus the presence of the Fixes tag below is intentional, to
facilitate backporting.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-2-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The microphone detection work scheduled by a prior jack insertion
interrupt may still be in a pending state or under execution when a jack
ejection interrupt has been fired.
This might lead to a racing condition or nau8821_jdet_work() completing
after nau8821_eject_jack(), which will override the currently
disconnected state of the jack and incorrectly report the headphone or
the headset as being connected.
Cancel any pending jdet_work or wait for its execution to finish before
attempting to handle the ejection interrupt.
Proceed similarly before launching the eject handler as a consequence of
detecting an invalid insert interrupt.
Fixes: aab1ad11d6 ("ASoC: nau8821: new driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251003-nau8821-jdet-fixes-v1-1-f7b0e2543f09@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
FF-A v1.2 introduced 16 byte IMPLEMENTATION DEFINED value in the endpoint
memory access descriptor to allow any sender could to specify an its any
custom value for each receiver. Also this value must be specified by the
receiver when retrieving the memory region. The sender must ensure it
informs the receiver of this value via an IMPLEMENTATION DEFINED mechanism
such as a partition message.
So the FF-A driver can use the message interfaces to communicate the value
and set the same in the ffa_mem_region_attributes structures when using
the memory interfaces.
The driver ensure that the size of the endpoint memory access descriptors
is set correctly based on the FF-A version.
Fixes: 9fac08d9d9 ("firmware: arm_ffa: Upgrade FF-A version to v1.2 in the driver")
Reported-by: Lixiang Mao <liximao@qti.qualcomm.com>
Tested-by: Lixiang Mao <liximao@qti.qualcomm.com>
Message-Id: <20250923150927.1218364-1-sudeep.holla@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fix several kernel-doc warnings in `drivers/android/binder.c` caused by
undocumented struct members and function parameters.
In particular, add missing documentation for the `@thread` parameter in
binder_free_buf_locked().
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Acked-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Binder only sends out freeze notifications when ioctl_freeze() completes
and the process has become fully frozen. However, if a freeze
notification is registered during the freeze operation, then it
registers an initial state of 'frozen'. This is a problem because if
the freeze operation fails, then the listener is not told about that
state change, leading to lost updates.
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace issues commands to a freeze listener, it identifies it
using a cookie. Normally this cookie uniquely identifies a freeze
listener, but when userspace clears a listener with the intent of
deleting it, it's allowed to "regret" clearing it and create a new
freeze listener for the same node using the same cookie. (IMO this was
an API mistake, but userspace relies on it.)
Currently if the active freeze listener gets fully deleted while there
are still pending duplicates, then the code incorrectly deletes the
pending duplicates too. To fix this, do not delete the entry if there
are still pending duplicates.
Since the current data structure requires a main freeze listener, we
convert one pending duplicate into the primary listener in this
scenario.
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider the following scenario:
1. A freeze notification is delivered to thread 1.
2. The process becomes frozen or unfrozen.
3. The message for step 2 is delivered to thread 2 and ignored because
there is already a pending notification from step 1.
4. Thread 1 acknowledges the notification from step 1.
In this case, step 4 should ensure that the message ignored in step 3 is
resent as it can now be delivered.
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clippy reports:
error: replacing a value of type `T` with `T::default()` is better expressed using `core::mem::take`
--> drivers/android/binder/node.rs:690:32
|
690 | _unused_capacity = mem::replace(&mut inner.freeze_list, KVVec::new());
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ help: consider using: `core::mem::take(&mut inner.freeze_list)`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#mem_replace_with_default
= note: `-D clippy::mem-replace-with-default` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(clippy::mem_replace_with_default)]`
The suggestion seems fine, thus apply it.
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fmh_gpib driver contains a device reference count leak in
fmh_gpib_attach_impl() where driver_find_device() increases the
reference count of the device by get_device() when matching but this
reference is not properly decreased. Add put_device() in
fmh_gpib_detach(), which ensures that the reference count of the
device is correctly managed.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 8e4841a088 ("staging: gpib: Add Frank Mori Hess FPGA PCI GPIB driver")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ATN (Attention) line is asserted during a read we get a
NIUSB_ATN_STATE_ERROR during a read. For the controller to send a
device clear it asserts ATN. Normally this is an error but in the case
of a device clear it should be regarded as an interrupt.
Return -EINTR when the Device Clear Active State (DCAS) is entered
else signal an error with dev_dbg with status instead of just dev_err.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was not sending device clear or trigger events when the
board entered the DCAS or DTAS state respectively in device mode.
DCAS is the Device Clear Active State which is entered on receiving a
selective device clear message (SDC) or universal device clear message
(DCL) from the controller in charge.
DTAS is the Device Trigger Active State which is entered on receiving
a group execute trigger (GET) message from the controller.
In order for an application, implementing a particular device, to
detect when one of these states is entered the driver needs to send
the appropriate event.
Send the appropriate gpib_event when DCAS or DTAS is set in the
reported status word. This sets the DCAS or DTAS bits in the board's
status word which can be monitored by the application.
Fixes: 4e127de14f ("staging: gpib: Add National Instruments USB GPIB driver")
Cc: stable <stable@kernel.org>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EOI (End Or Identify) is a hardware line on the GPIB bus that can be
asserted with the last byte of a message to indicate the end of the
transfer to the receiving device.
In this driver, a write with send_eoi true is done in 3 parts:
Send first byte directly
Send remaining but 1 bytes using the fifo
Send the last byte directly with EOI asserted
The first byte in a write is always sent by writing to the tms9914
chip directly to setup for the subsequent fifo transfer. We were not
checking for a 1 byte write with send_eoi true resulting in EOI not
being asserted. Since the fifo transfer was not executed
(fifotransfersize == 0) the retval in the test after the fifo transfer
code was still 1 from the preceding direct write. This caused it to
return without executing the final direct write which would have sent
an unsollicited extra byte.
For a 2 byte message the first byte was sent directly. But since the
fifo transfer was not executed (fifotransfersize == 1) and the retval
in the test after the fifo transfer code was still 1 from the
preceding first byte write it returned before the final direct byte
write with send_eoi true. The second byte was then sent as a separate
1 byte write to complete the 2 byte write count again without EOI
being asserted as above.
Only send the first byte directly if more than 1 byte is to be
transferred with send_eoi true.
Also check for retval < 0 for the error return in case the fifo code
is not used (1 or 2 byte message with send_eoi true).
Fixes: 09a4655ee1 ("staging: gpib: Add HP/Agilent/Keysight 8235xx PCI GPIB driver")
Cc: stable <stable@kernel.org>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The software reset for TAS5825 is different form other chips, as it will
set as 0x11 instead of 0x1 during reset in the tasdevice_reset(). So set
tas2781_hda::tasdevice_priv::chip_id as TAS5825, tasdevice_reset() can
work correctly.
Fixes: 7ceb69ca82 ("ASoC: tas2781: Add tas2118, tas2x20, tas5825 support")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the missing multiport controller binding to target list.
Fix minItems for interrupt-names to avoid the following error on High
Speed controller:
usb@a200000: interrupt-names: ['dwc_usb3', 'pwr_event', 'dp_hs_phy_irq', 'dm_hs_phy_irq'] is too short
Fixes: 6e762f7b8e ("dt-bindings: usb: Introduce qcom,snps-dwc3")
Cc: stable@vger.kernel.org
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel USBIO driver is x86 only, other architectures have ACPI
so add an appropriate depenecy plus compile test.
Fixes: 121a0f839d ("usb: misc: Add Intel USBIO bridge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ports definition currently defined in the usb-switch.yaml
fits standards devices which are either recipient of altmode
muxing and orientation switching events or an element of the
USB Super Speed data lanes.
This doesn't necessarely fit combo PHYs like the Qualcomm
USB3/DP Combo which has a different ports representation.
Move the ports definition to a separate usb-switch-ports.yaml
and reference it next to the usb-switch.yaml, except for
the Qualcomm USB3/DP Combo PHY bindings.
Reported-by: Rob Herring <robh@kernel.org>
Closes: https://lore.kernel.org/all/175462129176.394940.16810637795278334342.robh@kernel.org/
Fixes: 3bad7fe227 ("dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp: Reference usb-switch.yaml to allow mode-switch")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_bulk_get_all_enabled() is used in the probe, so
clk_bulk_disable_unprepare() should not be called explicitly in the remove
function.
Fixes: e0b6dc00c7 ("usb: dwc3: add generic driver to support flattened")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6d4405b16d ("ata: libata-core: Cache the general purpose log
directory") introduced caching of a device general purpose log directory
to avoid repeated access to this log page during device scan. This
change also added a check on this log page to verify that the log page
version is 0x0001 as mandated by the ACS specifications.
And it turns out that some devices do not bother reporting this version,
instead reporting a version 0, resulting in error messages such as:
ata6.00: Invalid log directory version 0x0000
and to the device being marked as not supporting the general purpose log
directory log page.
Since before commit 6d4405b16d the log page version check did not
exist and things were still working correctly for these devices, relax
ata_read_log_directory() version check and only warn about the invalid
log page version number without disabling access to the log directory
page.
Fixes: 6d4405b16d ("ata: libata-core: Cache the general purpose log directory")
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220635
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Fadump allocates memory to pass additional kernel command-line argument
to the fadump kernel. However, this allocation is not needed when fadump
is disabled. So avoid allocating memory for the additional parameter
area in such cases.
Fixes: f4892c68ec ("powerpc/fadump: allocate memory for additional parameters early")
Reviewed-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Fixes: f4892c68ec ("powerpc/fadump: allocate memory for additional parameters early")
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20251008032934.262683-1-sourabhjain@linux.ibm.com
Commit cc0cc23bab ("powerpc/xive: Untangle xive from child interrupt
controller drivers") changed xive_irq_data to be stashed to chip_data
instead of handler_data. However, multiple places are still attempting to
read xive_irq_data from handler_data and get a NULL pointer deference bug.
Update them to read xive_irq_data from chip_data.
Non-XIVE files which touch xive_irq_data seem quite strange to me,
especially the ocxl driver. I think there ought to be an alternative
platform-independent solution, instead of touching XIVE's data directly.
Therefore, I think this whole thing should be cleaned up. But perhaps I
just misunderstand something. In any case, this cleanup would not be
trivial; for now, just get things working again.
Fixes: cc0cc23bab ("powerpc/xive: Untangle xive from child interrupt controller drivers")
Reported-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Closes: https://lore.kernel.org/linuxppc-dev/68e48df8.170a0220.4b4b0.217d@mx.google.com/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com> # ocxl
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20251008081359.1382699-1-namcao@linutronix.de
Convert remaining __init__ files similar to what we did in
commit b615879dbf ("selftests: drv-net: make linters happy with our imports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no error handling for `dma_map_single()` failures.
Add error handling by checking `dma_mapping_error()` and freeing
the `skb` using `dev_kfree_skb()` (process context) when it fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Tested-on: D-Link DGE-550T Rev-A3
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit tx/rx buffer address to 32-bit address space for board with more
than 4GB DRAM.
Fixes: 804775dfc2 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Fixes: 6757d345dd ("net: ethernet: mtk_wed: introduce hw_rro support for MT7988")
Tested-by: Daniel Pawlik <pawlik.dan@gmail.com>
Tested-by: Matteo Croce <teknoraver@meta.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan78xx_write_raw_eeprom failed to properly propagate EEPROM
write timeout errors (-ETIMEDOUT). In the timeout fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error saved in ret.
As a result, callers could mistakenly treat EEPROM write operation as
successful even though the EEPROM write had actually timed out with no
or partial data write.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM write timeout error saved
in ret to the caller.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
cc: stable@vger.kernel.org
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is now a new LT9211 rev. U5, which reports chip ID 0x18 0x01 0xe4 .
The previous LT9211 reported chip ID 0x18 0x01 0xe3 , which is what the
driver checks for right now. Since there is a possibility there will be
yet another revision of the LT9211 in the future, drop the last version
nibble check to allow all future revisions of the chip to work with this
driver.
This fix makes LT9211 rev. U5 work with this driver.
Fixes: 8ce4129e3d ("drm/bridge: lt9211: Add Lontium LT9211 bridge driver")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251011110017.12521-1-marek.vasut@mailbox.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
There're several different actual hardwares sold by Huawei, using the
same USB ID 12d1:3a07.
The first one we found, having a volume control named "Headset Playback
Volume", reports a min value -15360, and will mute iff setting it to
-15360. It can be simply fixed by quirk flag MIXER_PLAYBACK_MIN_MUTE,
which we have already submitted previously.[1]
The second one we found today, having a volume control named "PCM
Playback Volume", reports its min -11520 and res 256, and will mute
when less than -11008. Because of the already existing quirk flag, we
can just set its min to -11264, and the new minimum value will still
not be available to userspace, so that userspace's minimum will be the
correct -11008.
1. https://lore.kernel.org/all/20250903-sound-v1-3-d4ca777b8512@uniontech.com/
Tested-by: Guoli An <anguoli@uniontech.com>
Signed-off-by: Cryolitia PukNgae <cryolitia.pukngae@linux.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This motherboard uses USB audio instead, causing this driver to complain
about "no codecs found!".
Add it to the denylist to silence the warning.
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The __component_match_add function may assign the 'matchptr' pointer
the value ERR_PTR(-ENOMEM), which will subsequently be dereferenced.
The call stack leading to the error looks like this:
hda_component_manager_init
|-> component_match_add
|-> component_match_add_release
|-> __component_match_add ( ... ,**matchptr, ... )
|-> *matchptr = ERR_PTR(-ENOMEM); // assign
|-> component_master_add_with_match( ... match)
|-> component_match_realloc(match, match->num); // dereference
Add IS_ERR() check to prevent the crash.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ae7abe36e3 ("ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Return value of a function acpi_evaluate_dsm() is dereferenced without
checking for NULL, but it is usually checked for this function.
acpi_evaluate_dsm() may return NULL, when acpi_evaluate_object() returns
acpi_status other than ACPI_SUCCESS, so add a check to prevent the crach.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 447106e92a ("ALSA: hda: cs35l41: Support mute notifications for CS35L41 HDA")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extract the guest_memfd test's SIGBUS handling functionality into a common
TEST_EXPECT_SIGBUS() macro in anticipation of adding more SIGBUS testcases.
Eating a SIGBUS isn't terrible difficult, but it requires a non-trivial
amount of boilerplate code, and using a macro allows selftests to print
out the exact action that failed to generate a SIGBUS without the developer
needing to remember to add a useful error message.
Explicitly mark the SIGBUS handler as "used", as gcc-14 at least likes to
discard the function before linking.
Opportunistically use TEST_FAIL(...) instead of TEST_ASSERT(false, ...),
and fix the write path of the guest_memfd test to use the local "val"
instead of hardcoding the literal value a second time.
Suggested-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Tested-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: Lisa Wang <wyihan@google.com>
Tested-by: Lisa Wang <wyihan@google.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-12-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
If a VM type supports KVM_CAP_GUEST_MEMFD_MMAP, the guest_memfd test will
run all test cases with GUEST_MEMFD_FLAG_MMAP set. This leaves the code
path for creating a non-mmap()-able guest_memfd on a VM that supports
mappable guest memfds untested.
Refactor the test to run the main test suite with a given set of flags.
Then, for VM types that support the mappable capability, invoke the test
suite twice: once with no flags, and once with GUEST_MEMFD_FLAG_MMAP
set.
This ensures both creation paths are properly exercised on capable VMs.
Run test_guest_memfd_flags() only once per VM type since it depends only
on the set of valid/supported flags, i.e. iterating over an arbitrary set
of flags is both unnecessary and wrong.
Signed-off-by: Ackerley Tng <ackerleytng@google.com>
[sean: use double-underscores for the inner helper]
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-9-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Use a global variable to track the host page size in the guest_memfd test
so that the information doesn't need to be constantly passed around. The
state is purely a reflection of the underlying system, i.e. can't be set
by the test and is constant for a given invocation of the test, and thus
explicitly passing the host page size to individual testcases adds no
value, e.g. doesn't allow testing different combinations.
Making page_size a global will simplify an upcoming change to create a new
guest_memfd instance per testcase.
No functional change intended.
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Tested-by: Ackerley Tng <ackerleytng@google.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Allow mmap() on guest_memfd instances for x86 VMs with private memory as
the need to track private vs. shared state in the guest_memfd instance is
only pertinent to INIT_SHARED. Doing mmap() on private memory isn't
terrible useful (yet!), but it's now possible, and will be desirable when
guest_memfd gains support for other VMA-based syscalls, e.g. mbind() to
set NUMA policy.
Lift the restriction now, before MMAP support is officially released, so
that KVM doesn't need to add another capability to enumerate support for
mmap() on private memory.
Fixes: 3d3a04fad2 ("KVM: Allow and advertise support for host mmap() on guest_memfd files")
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Tested-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add KVM_GENERIC_MMU_NOTIFIER as a dependency for selecting KVM_GUEST_MEMFD,
as guest_memfd relies on kvm_mmu_invalidate_{begin,end}(), which are
defined if and only if the generic mmu_notifier implementation is enabled.
The missing dependency is currently benign as s390 is the only KVM arch
that doesn't utilize the generic mmu_notifier infrastructure, and s390
doesn't currently support guest_memfd.
Fixes: a7800aa80e ("KVM: Add KVM_CREATE_GUEST_MEMFD ioctl() for guest-specific backing memory")
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
When invalidating gmem ranges, e.g. in response to PUNCH_HOLE, process all
possible range types (PRIVATE vs. SHARED) for the gmem instance. Since
since guest_memfd doesn't yet support in-place conversions, simply pivot
on INIT_SHARED as a gmem instance can currently only have private or shared
memory, not both.
Failure to mark shared GPAs for invalidation is benign in the current code
base, as only x86's TDX consumes KVM_FILTER_{PRIVATE,SHARED}, and TDX
doesn't yet support INIT_SHARED with guest_memfd. However, invalidating
only private GPAs is conceptually wrong and a lurking bug, e.g. could
result in missed invalidations if ARM starts filtering invalidations based
on attributes.
Fixes: 3d3a04fad2 ("KVM: Allow and advertise support for host mmap() on guest_memfd files")
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add a guest_memfd flag to allow userspace to state that the underlying
memory should be configured to be initialized as shared, and reject user
page faults if the guest_memfd instance's memory isn't shared. Because
KVM doesn't yet support in-place private<=>shared conversions, all
guest_memfd memory effectively follows the initial state.
Alternatively, KVM could deduce the initial state based on MMAP, which for
all intents and purposes is what KVM currently does. However, implicitly
deriving the default state based on MMAP will result in a messy ABI when
support for in-place conversions is added.
For x86 CoCo VMs, which don't yet support MMAP, memory is currently private
by default (otherwise the memory would be unusable). If MMAP implies
memory is shared by default, then the default state for CoCo VMs will vary
based on MMAP, and from userspace's perspective, will change when in-place
conversion support is added. I.e. to maintain guest<=>host ABI, userspace
would need to immediately convert all memory from shared=>private, which
is both ugly and inefficient. The inefficiency could be avoided by adding
a flag to state that memory is _private_ by default, irrespective of MMAP,
but that would lead to an equally messy and hard to document ABI.
Bite the bullet and immediately add a flag to control the default state so
that the effective behavior is explicit and straightforward.
Fixes: 3d3a04fad2 ("KVM: Allow and advertise support for host mmap() on guest_memfd files")
Cc: David Hildenbrand <david@redhat.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Tested-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Rework the not-yet-released KVM_CAP_GUEST_MEMFD_MMAP into a more generic
KVM_CAP_GUEST_MEMFD_FLAGS capability so that adding new flags doesn't
require a new capability, and so that developers aren't tempted to bundle
multiple flags into a single capability.
Note, kvm_vm_ioctl_check_extension_generic() can only return a 32-bit
value, but that limitation can be easily circumvented by adding e.g.
KVM_CAP_GUEST_MEMFD_FLAGS2 in the unlikely event guest_memfd supports more
than 32 flags.
Reviewed-by: Ackerley Tng <ackerleytng@google.com>
Tested-by: Ackerley Tng <ackerleytng@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20251003232606.4070510-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Explicitly zero kvm_host_pmu instead of attempting to get the perf PMU
capabilities when running on a hybrid CPU to avoid running afoul of perf's
sanity check.
------------[ cut here ]------------
WARNING: arch/x86/events/core.c:3089 at perf_get_x86_pmu_capability+0xd/0xc0,
Call Trace:
<TASK>
kvm_x86_vendor_init+0x1b0/0x1a40 [kvm]
vmx_init+0xdb/0x260 [kvm_intel]
vt_init+0x12/0x9d0 [kvm_intel]
do_one_initcall+0x60/0x3f0
do_init_module+0x97/0x2b0
load_module+0x2d08/0x2e30
init_module_from_file+0x96/0xe0
idempotent_init_module+0x117/0x330
__x64_sys_finit_module+0x73/0xe0
Always read the capabilities for non-hybrid CPUs, i.e. don't entirely
revert to reading capabilities if and only if KVM wants to use a PMU, as
it may be useful to have the host PMU capabilities available, e.g. if only
or debug.
Reported-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Closes: https://lore.kernel.org/all/70b64347-2aca-4511-af78-a767d5fa8226@intel.com/
Fixes: 51f34b1e65 ("KVM: x86/pmu: Snapshot host (i.e. perf's) reported PMU capabilities")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20251010005239.146953-1-dapeng1.mi@linux.intel.com
[sean: rework changelog, call out hybrid CPUs in shortlog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
syzbot reported a BUG_ON in ext4_es_cache_extent() when opening a verity
file on a corrupted ext4 filesystem mounted without a journal.
The issue is that the filesystem has an inode with both the INLINE_DATA
and EXTENTS flags set:
EXT4-fs error (device loop0): ext4_cache_extents:545: inode #15:
comm syz.0.17: corrupted extent tree: lblk 0 < prev 66
Investigation revealed that the inode has both flags set:
DEBUG: inode 15 - flag=1, i_inline_off=164, has_inline=1, extents_flag=1
This is an invalid combination since an inode should have either:
- INLINE_DATA: data stored directly in the inode
- EXTENTS: data stored in extent-mapped blocks
Having both flags causes ext4_has_inline_data() to return true, skipping
extent tree validation in __ext4_iget(). The unvalidated out-of-order
extents then trigger a BUG_ON in ext4_es_cache_extent() due to integer
underflow when calculating hole sizes.
Fix this by detecting this invalid flag combination early in ext4_iget()
and rejecting the corrupted inode.
Cc: stable@kernel.org
Reported-and-tested-by: syzbot+038b7bf43423e132b308@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=038b7bf43423e132b308
Suggested-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Message-ID: <20250930112810.315095-1-kartikey406@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Some of the details about how directory hash trees work were confusing or
outright wrong, this patch should fix those.
A note on dx_tail's dt_reserved member, as far as I can tell the kernel
never sets this explicitly, so its content is apparently left-overs from
what was there before (for the dx_root I've seen remnants of a
ext4_dir_entry_tail struct from when the dir was not yet a hash dir).
Signed-off-by: Zeno Endemann <zeno.endemann@mailbox.org>
Message-ID: <20250925152435.22749-1-zeno.endemann@mailbox.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When freeing metadata blocks in nojournal mode, ext4_forget() calls
bforget() to clear the dirty flag on the buffer_head and remvoe
associated mappings. This is acceptable if the metadata has not yet
begun to be written back. However, if the write-back has already started
but is not yet completed, ext4_forget() will have no effect.
Subsequently, ext4_mb_clear_bb() will immediately return the block to
the mb allocator. This block can then be reallocated immediately,
potentially causing an data corruption issue.
Fix this by clearing the buffer's dirty flag and waiting for the ongoing
I/O to complete, ensuring that no further writes to stale data will
occur.
Fixes: 16e08b14a4 ("ext4: cleanup clean_bdev_aliases() calls")
Cc: stable@kernel.org
Reported-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Closes: https://lore.kernel.org/linux-ext4/a9417096-9549-4441-9878-b1955b899b4e@huaweicloud.com/
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20250916093337.3161016-3-yi.zhang@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When releasing file system metadata blocks in jbd2_journal_forget(), if
this buffer has not yet been checkpointed, it may have already been
written back, currently be in the process of being written back, or has
not yet written back. jbd2_journal_forget() calls
jbd2_journal_try_remove_checkpoint() to check the buffer's status and
add it to the current transaction if it has not been written back. This
buffer can only be reallocated after the transaction is committed.
jbd2_journal_try_remove_checkpoint() attempts to lock the buffer and
check its dirty status while holding the buffer lock. If the buffer has
already been written back, everything proceeds normally. However, there
are two issues. First, the function returns immediately if the buffer is
locked by the write-back process. It does not wait for the write-back to
complete. Consequently, until the current transaction is committed and
the block is reallocated, there is no guarantee that the I/O will
complete. This means that ongoing I/O could write stale metadata to the
newly allocated block, potentially corrupting data. Second, the function
unlocks the buffer as soon as it detects that the buffer is still dirty.
If a concurrent write-back occurs immediately after this unlocking and
before clear_buffer_dirty() is called in jbd2_journal_forget(), data
corruption can theoretically still occur.
Although these two issues are unlikely to occur in practice since the
undergoing metadata writeback I/O does not take this long to complete,
it's better to explicitly ensure that all ongoing I/O operations are
completed.
Fixes: 597599268e ("jbd2: discard dirty data when forgetting an un-journalled buffer")
Cc: stable@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20250916093337.3161016-2-yi.zhang@huaweicloud.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The backing_file_write_iter() function, which is called
immediately after this code, already contains identical
logic to clear the IOCB_DIO_CALLER_COMP flag along with
the same explanatory comment. There is no need to duplicate
this operation in the overlayfs code.
Signed-off-by: Seong-Gwang Heo <heo@mykernel.net>
Fixes: a6293b3e28 ("fs: factor out backing_file_{read,write}_iter() helpers")
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
These syscalls call to vfs_fileattr_get/set functions which return
ENOIOCTLCMD if filesystem doesn't support setting file attribute on an
inode. For syscalls EOPNOTSUPP would be more appropriate return error.
Signed-off-by: Andrey Albershteyn <aalbersh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Newer firmware bundles contain a flash utility whose size exceeds
the currently allowed limit. Increase the maximum allowed size
to accommodate the newer utility version.
Without this patch:
# devlink dev flash i2c/1-0070 file fw_nosplit_v3.hex
Failed to load firmware
Flashing failed
Error: zl3073x: FW load failed: [utility] component is too big (11000 bytes)
Fixes: ca017409da ("dpll: zl3073x: Add firmware loading functionality")
Suggested-by: Prathosh Satish <Prathosh.Satish@microchip.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251008141418.841053-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This kconfig symbol has dependencies and is only selectable if those
dependencies are also enabled.
Respect the dependencies.
Fixes the following warning when configuring an 'allnoconfig':
WARNING: unmet direct dependencies detected for ARCH_HAS_ELF_CORE_EFLAGS
Depends on [n]: BINFMT_ELF [=n] && ELF_CORE [=y]
Selected by [y]:
- RISCV [=y]
Fixes: 8c94db0ae9 ("binfmt_elf: preserve original ELF e_flags for core dumps")
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20251009-riscv-elf-core-eflags-v1-1-e9b45ab6b36d@linutronix.de
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Similar to the ARM64 commit 3505f30fb6a9s ("ARM64 / ACPI: If we chose
to boot from acpi then disable FDT"), let's not do DT hardware probing
if ACPI is enabled in early boot. This avoids errors caused by
repeated driver probing.
Signed-off-by: Han Gao <rabenda.cn@gmail.com>
Link: https://lore.kernel.org/r/20250910112401.552987-1-rabenda.cn@gmail.com
[pjw@kernel.org: cleaned up patch description and subject]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
When adding a kprobe such as "p:probe/tcp_sendmsg _text+15392192",
arch_check_kprobe would start iterating all instructions starting from
_text until the probed address. Not only is this very inefficient, but
literal values in there (e.g. left by function patching) are
misinterpreted in a way that causes a desync.
Fix this by doing it like x86: start the iteration at the closest
preceding symbol instead of the given starting point.
Fixes: 87f48c7ccc ("riscv: kprobe: Fixup kernel panic when probing an illegal position")
Signed-off-by: Fabian Vogt <fvogt@suse.de>
Signed-off-by: Marvin Friedrich <marvin.friedrich@suse.com>
Acked-by: Guo Ren <guoren@kernel.org>
Link: https://lore.kernel.org/r/6191817.lOV4Wx5bFT@fvogt-thinkpad
Signed-off-by: Paul Walmsley <pjw@kernel.org>
openSBI v1.7 adds harts checks for ipi operations. Especially it
adds comparison between hmask passed as an argument from linux
and mask of online harts (from openSBI side). If they don't
fit each other the error occurs.
When cpu is offline, cpu_online_mask is explicitly cleared in
__cpu_disable. However, there is no explicit clearing of
mm_cpumask. mm_cpumask is used for rfence operations that
call openSBI RFENCE extension which uses ipi to remote harts.
If hart is offline there may be error if mask of linux is not
as mask of online harts in openSBI.
this patch adds explicit clearing of mm_cpumask for offline hart.
Signed-off-by: Danil Skrebenkov <danil.skrebenkov@cloudbear.ru>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20250919132849.31676-1-danil.skrebenkov@cloudbear.ru
[pjw@kernel.org: rewrote subject line for clarity]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
The current value of BUFMAX is similar as in other architectures, but as
per documentation on KGDB (see
'Documentation/process/debugging/kgdb.rst'), BUFMAX has to be larger
than NUMREGBYTES.
Some NUMREGBYTES architectures (e.g. powerpc or hexagon) actually define
BUFMAX in relation to NUMREGBYTES, and thus this condition is always
guaranteed. Since 2048 is a value that is generally accepted on all
architectures, and that is larger than the current value of NUMREGBYTES,
we can keep this value in arch/riscv, but we can at least add an
'static_assert' as an extra measure just in case NUMREGBYTES changes in
the future for some unforseen reason.
Signed-off-by: Miquel Sabaté Solà <mikisabate@gmail.com>
Link: https://lore.kernel.org/r/20250915143252.154955-1-mikisabate@gmail.com
Signed-off-by: Paul Walmsley <pjw@kernel.org>
The kernel uses the standard rustc targets for non-x86 targets, and out
of those only 64-bit arm's target has kcfi support enabled. For x86, the
custom 64-bit target enables kcfi.
The HAVE_CFI_ICALL_NORMALIZE_INTEGERS_RUSTC config option that allows
CFI_CLANG to be used in combination with RUST does not check whether the
rustc target supports kcfi. This breaks the build on riscv (and
presumably 32-bit arm) when CFI_CLANG and RUST are enabled at the same
time.
Ordinarily, a rustc-option check would be used to detect target support
but unfortunately rustc-option filters out the target for reasons given
in commit 46e24a545c ("rust: kasan/kbuild: fix missing flags on first
build"). As a result, if the host supports kcfi but the target does not,
e.g. when building for riscv on x86_64, the build would remain broken.
Instead, make HAVE_CFI_ICALL_NORMALIZE_INTEGERS_RUSTC depend on the only
two architectures where the target used supports it to fix the build.
CC: stable@vger.kernel.org
Fixes: ca627e6365 ("rust: cfi: add support for CFI_CLANG with Rust")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250908-distill-lint-1ae78bcf777c@spud
Signed-off-by: Paul Walmsley <pjw@kernel.org>
For queue-depth I/O policy, this patch fixes unbalanced I/Os across
nvme multipaths.
Issue Description:
The RETRY disposition incorrectly increments ns->ctrl->nr_active
counter and reinitializes iostat start-time. In such cases nr_active
counter never goes back to zero until that path disconnects and
reconnects.
Such a path is not chosen for new I/Os if multiple RETRY cases on a given
a path cause its queue-depth counter to be artificially higher compared
to other paths. This leads to unbalanced I/Os across paths.
The patch skips incrementing nr_active if NVME_MPATH_CNT_ACTIVE is already
set. And it skips restarting io stats if NVME_MPATH_IO_STATS is already set.
base-commit: e989a3da2d371a4b6597ee8dee5c72e407b4db7a
Fixes: d4d957b53d ("nvme-multipath: support io stats on the mpath device")
Signed-off-by: Amit Chaudhary <achaudhary@purestorage.com>
Reviewed-by: Randy Jennings <randyj@purestorage.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Currently the Panthor driver needs the GPU to be powered down
between suspend and resume. If this is not done, then the
MCU_CONTROL register will be preserved as AUTO, which again will
cause a premature FW boot on resume. The FW will go directly into
fatal state in this case.
This case needs to be handled as there is no guarantee that the
GPU will be powered down after the suspend callback on all platforms.
The fix is to call panthor_fw_stop() in "pre-reset" path to ensure
the MCU_CONTROL register is cleared (set DISABLE). This matches
well with the already existing call to panthor_fw_start() from the
"post-reset" path.
Signed-off-by: Ketil Johnsen <ketil.johnsen@arm.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Fixes: 2718d91816 ("drm/panthor: Add the FW logical block")
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20251008105112.4077015-1-ketil.johnsen@arm.com
Marc Kleine-Budde <mkl@pengutronix.de> says:
The first patch fixes a pm_runtime imbalance in the m_can_platform
driver.
The rest of this series fixes the CAN state handling in the m_can
driver:
- add the missing state transition from "Error Warning" back to "Error
Active" (patch 2)
- address the fact that in some SoCs (observed on the STM32MP15) the
M_CAN IP core keeps the CAN state and CAN error counters over an
internal reset cycle. Set the correct CAN state during ifup and
system resume (patches 3+4)
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-0-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A suspend/resume cycle on a down interface results in the interface
coming up in Error Active state. A suspend/resume cycle on an Up
interface will always result in Error Active state, regardless of the
actual CAN state.
During suspend, only set running interfaces to CAN_STATE_SLEEPING.
During resume only touch the CAN state of running interfaces. For
wakeup sources, set the CAN state depending on the Protocol Status
Regitser (PSR), for non wakeup source interfaces m_can_start() will do
the same.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-4-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In some SoCs (observed on the STM32MP15) the M_CAN IP core keeps the
CAN state and CAN error counters over an internal reset cycle. An
external reset is not always possible, due to the shared reset with
the other CAN core. This caused the core not always be in Error Active
state when bringing up the controller.
Instead of always setting the CAN state to Error Active in
m_can_chip_config(), fix this by reading and decoding the Protocol
Status Regitser (PSR) and set the CAN state accordingly.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-3-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN Error State is determined by the receive and transmit error
counters. The CAN error counters decrease when reception/transmission
is successful, so that a status transition back to the Error Active
status is possible. This transition is not handled by
m_can_handle_state_errors().
Add the missing detection of the Error Active state to
m_can_handle_state_errors() and extend the handling of this state in
m_can_handle_state_change().
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Fixes: cd0d83eab2 ("can: m_can: m_can_handle_state_change(): fix state change")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-2-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 227619c3ff ("can: m_can: move runtime PM enable/disable to
m_can_platform") moved the PM runtime enable from the m_can core
driver into the m_can_platform.
That patch forgot to move the pm_runtime_disable() to
m_can_plat_remove(), so that unloading the m_can_platform driver
causes an "Unbalanced pm_runtime_enable!" error message.
Add the missing pm_runtime_disable() to m_can_plat_remove() to fix the
problem.
Cc: Patrik Flykt <patrik.flykt@linux.intel.com>
Fixes: 227619c3ff ("can: m_can: move runtime PM enable/disable to m_can_platform")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-1-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver supports USB devices with more than 1 CAN channel.
In old kernel before 3.15, it uses net_device->dev_id to distinguish
different channel in userspace, which was done in commit
acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id").
But since 3.15, the correct way is populating net_device->dev_port.
And according to documentation, if network device support multiple
interface, lack of net_device->dev_port SHALL be treated as a bug.
Fixes: acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id")
Cc: stable@vger.kernel.org
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-populate-net_device-dev_port-v1-1-68a065de6937@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This issue was found by Runcheng Lu when develop HSCanT USB to CAN FD
converter[1]. The original developers may have only 3 interfaces
device to test so they write 3 here and wait for future change.
During the HSCanT development, we actually used 4 interfaces, so the
limitation of 3 is not enough now. But just increase one is not
future-proofed. Since the channel index type in gs_host_frame is u8,
just make canch[] become a flexible array with a u8 index, so it
naturally constraint by U8_MAX and avoid statically allocate 256
pointer for every gs_usb device.
[1]: https://github.com/cherry-embedded/HSCanT-hardware
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reported-by: Runcheng Lu <runcheng.lu@hpmicro.com>
Cc: stable@vger.kernel.org
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-max-if-v5-1-863330bf6666@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Expand the prefault memory selftest to add a regression test for a KVM bug
where KVM's retry logic would result in (breakable) deadlock due to the
memslot deletion waiting on prefaulting to release SRCU, and prefaulting
waiting on the memslot to fully disappear (KVM uses a two-step process to
delete memslots, and KVM x86 retries page faults if a to-be-deleted, a.k.a.
INVALID, memslot is encountered).
To exercise concurrent memslot remove, spawn a second thread to initiate
memslot removal at roughly the same time as prefaulting. Test memslot
removal for all testcases, i.e. don't limit concurrent removal to only the
success case. There are essentially three prefault scenarios (so far)
that are of interest:
1. Success
2. ENOENT due to no memslot
3. EAGAIN due to INVALID memslot
For all intents and purposes, #1 and #2 are mutually exclusive, or rather,
easier to test via separate testcases since writing to non-existent memory
is trivial. But for #3, making it mutually exclusive with #1 _or_ #2 is
actually more complex than testing memslot removal for all scenarios. The
only requirement to let memslot removal coexist with other scenarios is a
way to guarantee a stable result, e.g. that the "no memslot" test observes
ENOENT, not EAGAIN, for the final checks.
So, rather than make memslot removal mutually exclusive with the ENOENT
scenario, simply restore the memslot and retry prefaulting. For the "no
memslot" case, KVM_PRE_FAULT_MEMORY should be idempotent, i.e. should
always fail with ENOENT regardless of how many times userspace attempts
prefaulting.
Pass in both the base GPA and the offset (instead of the "full" GPA) so
that the worker can recreate the memslot.
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20250924174255.2141847-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Currently reset_control_deassert() is called without checking its
return value. This can lead to silent failures when reset deassertion
fails.
Add proper error handling to:
1. Check the return value of reset_control_deassert()
2. Return the error to the caller
3. Provide meaningful error message using dev_err_probe()
This ensures that reset-related failures are properly reported during
probe and helps with debugging reset issues.
Signed-off-by: Artem Shimko <a.shimko.dev@gmail.com>
Link: https://patch.msgid.link/20251007101134.1912895-1-a.shimko.dev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Prior to commit b52da4054e ("ipmi: Rework user message limit handling"),
i_ipmi_request() used to increase the user reference counter if the receive
message is provided by the caller of IPMI API functions. This is no longer
the case. However, ipmi_free_recv_msg() is still called and decreases the
reference counter. This results in the reference counter reaching zero,
the user data pointer is released, and all kinds of interesting crashes are
seen.
Fix the problem by increasing user reference counter if the receive message
has been provided by the caller.
Fixes: b52da4054e ("ipmi: Rework user message limit handling")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20251006201857.3433837-1-linux@roeck-us.net>
Signed-off-by: Corey Minyard <corey@minyard.net>
In be1e028302 ("coredump: don't pointlessly check and spew warnings")
we tried to fix input validation so it only happens during a write to
core_pattern. This would avoid needlessly logging a lot of warnings
during a read operation. However the logic accidently got inverted in
this commit. Fix it so the input validation only happens on write and is
skipped on read.
Fixes: be1e028302 ("coredump: don't pointlessly check and spew warnings")
Fixes: 16195d2c7d ("coredump: validate socket name as it is written")
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: Yu Watanabe <watanabe.yu@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
When user calls open_by_handle_at() on some inode that is not cached, we
will create disconnected dentry for it. If such dentry is a directory,
exportfs_decode_fh_raw() will then try to connect this dentry to the
dentry tree through reconnect_path(). It may happen for various reasons
(such as corrupted fs or race with rename) that the call to
lookup_one_unlocked() in reconnect_one() will fail to find the dentry we
are trying to reconnect and instead create a new dentry under the
parent. Now this dentry will not be marked as disconnected although the
parent still may well be disconnected (at least in case this
inconsistency happened because the fs is corrupted and .. doesn't point
to the real parent directory). This creates inconsistency in
disconnected flags but AFAICS it was mostly harmless. At least until
commit f1ee616214 ("VFS: don't keep disconnected dentries on d_anon")
which removed adding of most disconnected dentries to sb->s_anon list.
Thus after this commit cleanup of disconnected dentries implicitely
relies on the fact that dput() will immediately reclaim such dentries.
However when some leaf dentry isn't marked as disconnected, as in the
scenario described above, the reclaim doesn't happen and the dentries
are "leaked". Memory reclaim can eventually reclaim them but otherwise
they stay in memory and if umount comes first, we hit infamous "Busy
inodes after unmount" bug. Make sure all dentries created under a
disconnected parent are marked as disconnected as well.
Reported-by: syzbot+1d79ebe5383fc016cf07@syzkaller.appspotmail.com
Fixes: f1ee616214 ("VFS: don't keep disconnected dentries on d_anon")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The commit 168316db3583("dax: assert that i_rwsem is held
exclusive for writes") added lock assertions to ensure proper
locking in DAX operations. However, these assertions trigger
false-positive lockdep warnings since read lock is unnecessary
on read-only filesystems(e.g., erofs).
This patch skips the read lock assertion for read-only filesystems,
eliminating the spurious warnings while maintaining the integrity
checks for writable filesystems.
Fixes: 168316db35 ("dax: assert that i_rwsem is held exclusive for writes")
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Friendy Su <friendy.su@sony.com>
Reviewed-by: Daniel Palmer <daniel.palmer@sony.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The `BadFdError` doc comment mentions the `EBADF` constant but does
not currently provide a navigation target for readers of the
generated docs. Turning the references into intra-doc links matches
the rest of the module and makes the documentation easier to
explore.
Suggested-by: Onur Özkan <work@onurozkan.dev>
Link: https://github.com/Rust-for-Linux/linux/issues/1186
Signed-off-by: Tong Li <djfkvcing117@gmail.com>
Reviewed-by: Onur Özkan <work@onurozkan.dev>
Signed-off-by: Christian Brauner <brauner@kernel.org>
The f_count member in struct file has been replaced by f_ref,
so update f_count to f_ref in the comment.
Signed-off-by: Zhou Yuhang <zhouyuhang@kylinos.cn>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Replace VFS_WARN_ON_ONCE() with graceful error handling when file
handles contain inode numbers that don't match the actual namespace
inode. This prevents userspace from triggering kernel warnings by
providing malformed file handles to open_by_handle_at().
The issue occurs when userspace provides a file handle with valid
namespace type and ID that successfully locates a namespace, but
specifies an incorrect inode number. Previously, this would trigger
VFS_WARN_ON_ONCE() when comparing the real inode number against the
provided value.
Since file handle data is user-controllable, inode number mismatches
should be treated as invalid input rather than kernel consistency
errors. Handle this case by returning NULL to indicate the file
handle is invalid, rather than warning about what is essentially
user input validation.
Reported-by: syzbot+9eefe09bedd093f156c2@syzkaller.appspotmail.com
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Document the QMP UFS PHY compatible for Qualcomm Kaanapali to support
physical layer functionality for UFS found on the SoC. Use fallback to
indicate the compatibility of the QMP UFS PHY on the Kaanapali with that
on the SM8750.
Signed-off-by: Jingyi Wang <jingyi.wang@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "offset" comes from the skb->data that we received. Here the code
is verifying that "offset + len" is within bounds however it does not
take integer overflows into account. Use size_add() to be safe.
This would only be an issue on 32bit systems which are probably a very
small percent of the users. Still, it's worth fixing just for
correctness sake.
Fixes: 42e9a92fe6 ("[SCSI] libfc: A modular Fibre Channel library")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Message-Id: <aNvPMet7TPtM9CY1@stanley.mountain>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When selecting an outgoing channel for I/O, storvsc tries to select a
channel with a returning CPU that is not the same as issuing CPU. This
worked well in the past, however it doesn't work well when the Hyper-V
exposes a large number of channels (up to the number of all CPUs). Use a
different CPU for returning channel is not efficient on Hyper-V.
Change this behavior by preferring to the channel with the same CPU as
the current I/O issuing CPU whenever possible.
Tests have shown improvements in newer Hyper-V/Azure environment, and no
regression with older Hyper-V/Azure environments.
Tested-by: Raheel Abdul Faizy <rabdulfaizy@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Message-Id: <1759381530-7414-1-git-send-email-longli@linux.microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling intotify_show_fdinfo() on fd watching an overlayfs inode, while
the overlayfs is being unmounted, can lead to dereferencing NULL ptr.
This issue was found by syzkaller.
Race Condition Diagram:
Thread 1 Thread 2
-------- --------
generic_shutdown_super()
shrink_dcache_for_umount
sb->s_root = NULL
|
| vfs_read()
| inotify_fdinfo()
| * inode get from mark *
| show_mark_fhandle(m, inode)
| exportfs_encode_fid(inode, ..)
| ovl_encode_fh(inode, ..)
| ovl_check_encode_origin(inode)
| * deref i_sb->s_root *
|
|
v
fsnotify_sb_delete(sb)
Which then leads to:
[ 32.133461] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 32.134438] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 32.135032] CPU: 1 UID: 0 PID: 4468 Comm: systemd-coredum Not tainted 6.17.0-rc6 #22 PREEMPT(none)
<snip registers, unreliable trace>
[ 32.143353] Call Trace:
[ 32.143732] ovl_encode_fh+0xd5/0x170
[ 32.144031] exportfs_encode_inode_fh+0x12f/0x300
[ 32.144425] show_mark_fhandle+0xbe/0x1f0
[ 32.145805] inotify_fdinfo+0x226/0x2d0
[ 32.146442] inotify_show_fdinfo+0x1c5/0x350
[ 32.147168] seq_show+0x530/0x6f0
[ 32.147449] seq_read_iter+0x503/0x12a0
[ 32.148419] seq_read+0x31f/0x410
[ 32.150714] vfs_read+0x1f0/0x9e0
[ 32.152297] ksys_read+0x125/0x240
IOW ovl_check_encode_origin derefs inode->i_sb->s_root, after it was set
to NULL in the unmount path.
Fix it by protecting calling exportfs_encode_fid() from
show_mark_fhandle() with s_umount lock.
This form of fix was suggested by Amir in [1].
[1]: https://lore.kernel.org/all/CAOQ4uxhbDwhb+2Brs1UdkoF0a3NSdBAOQPNfEHjahrgoKJpLEw@mail.gmail.com/
Fixes: c45beebfde ("ovl: support encoding fid from inode with no alias")
Signed-off-by: Jakub Acs <acsjakub@amazon.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Christian Brauner <brauner@kernel.org>
Cc: linux-unionfs@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Use DMA-API dma_map_single() call for getting the DMA address of the
transfer buffer instead of hacking with virt_to_phys().
This fixes the following DMA-API debug warning:
------------[ cut here ]------------
DMA-API: rockchip-sfc fe300000.spi: device driver tries to sync DMA memory it has not allocated [device address=0x000000000cf70000] [size=288 bytes]
WARNING: kernel/dma/debug.c:1106 at check_sync+0x1d8/0x690, CPU#2: systemd-udevd/151
Modules linked in: ...
Hardware name: Hardkernel ODROID-M1 (DT)
pstate: 604000c9 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : check_sync+0x1d8/0x690
lr : check_sync+0x1d8/0x690
..
Call trace:
check_sync+0x1d8/0x690 (P)
debug_dma_sync_single_for_cpu+0x84/0x8c
__dma_sync_single_for_cpu+0x88/0x234
rockchip_sfc_exec_mem_op+0x4a0/0x798 [spi_rockchip_sfc]
spi_mem_exec_op+0x408/0x498
spi_nor_read_data+0x170/0x184
spi_nor_read_sfdp+0x74/0xe4
spi_nor_parse_sfdp+0x120/0x11f0
spi_nor_sfdp_init_params_deprecated+0x3c/0x8c
spi_nor_scan+0x690/0xf88
spi_nor_probe+0xe4/0x304
spi_mem_probe+0x6c/0xa8
spi_probe+0x94/0xd4
really_probe+0xbc/0x298
...
Fixes: b69386fcbc ("spi: rockchip-sfc: Using normal memory for dma")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20251003114239.431114-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit 5402c4d4d2 ("exportfs: require ->fh_to_parent() to encode
connectable file handles") we will fail to create non-decodable file
handles for filesystems without export operations. Fix it.
Fixes: 5402c4d4d2 ("exportfs: require ->fh_to_parent() to encode connectable file handles")
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The commit afa3701c0e ("cgroup: cgroup.stat.local time accounting")
introduced a seqcount to track freeze timing but initialized it as a
plain seqcount_t using seqcount_init().
However, the write-side critical section in cgroup_do_freeze() holds
the css_set_lock spinlock while calling write_seqcount_begin(). On
PREEMPT_RT kernels, spinlocks do not disable preemption, causing the
lockdep assertion for a plain seqcount_t, which checks for preemption
being disabled, to fail.
This triggers the following warning:
WARNING: CPU: 0 PID: 9692 at include/linux/seqlock.h:221
Fix this by changing the type to seqcount_spinlock_t and initializing
it with seqcount_spinlock_init() to associate css_set_lock with the
seqcount. This allows lockdep to correctly validate that the spinlock
is held during write operations, resolving the assertion failure on all
kernel configurations.
Reported-by: syzbot+27a2519eb4dad86d0156@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=27a2519eb4dad86d0156
Fixes: afa3701c0e ("cgroup: cgroup.stat.local time accounting")
Signed-off-by: Nirbhay Sharma <nirbhay.lkd@gmail.com>
Link: https://lore.kernel.org/r/20251002165510.KtY3IT--@linutronix.de/
Acked-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the binding for the Cadence spi controller was written, a dedicated
compatible was added for the zynq device. Later when zynqmp and
versal-net, which also use this spi controller IP, were added they did
not receive soc-specific compatibles. Add them now, with a fallback to
the existing compatible for the r1p6 version of the IP so that there
will be no functional change. Retain the r1p6 in the string, to match
what was done for zynq.
Disallow the cdns,spi-r1p6 compatible in isolation to "encourage" people
to actually add soc-specific compatible strings in the future.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20251001-basics-grafting-a1a214ef65ac@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
The Qualcomm Trusted Execution Environment (QTEE) is only available on
Qualcomm SoCs. Hence add a dependency on ARCH_QCOM, to prevent asking
the user about this driver when configuring a kernel without Qualcomm
platform support.
Fixes: d6e290837e ("tee: add Qualcomm TEE driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Re-order these checks to check if "i" is a valid array index before using
it. This prevents a potential off by one read access.
Fixes: d6e290837e ("tee: add Qualcomm TEE driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
2025-09-19 08:45:59 +02:00
690 changed files with 6350 additions and 3751 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
