Pull libata fixes from Tejun Heo:
"Three libata fixes for v3.18. Nothing too interesting. PCI ID ID and
quirk additions to ahci and an error handling path fix in sata_fsl"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable MSI on SAMSUNG 0xa800 SSD
sata_fsl: fix error handling of irq_of_parse_and_map
AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller
Pull watchdog fix from Wim Van Sebroeck:
"Fix the watchdog mask bit offset for Exynos7"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
Pull i2c fixes from Wolfram Sang:
"Here are two more driver bugfixes for I2C which would be good to have"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
Pull x86 fixes from Thomas Gleixner:
"Two final fixlets for 3.18:
- Prevent microcode reload wreckage on 32bit
- Unbreak cross compilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Limit the microcode reloading to 64-bit for now
x86: Use $(OBJDUMP) instead of plain objdump
Pull sound fixlet from Takashi Iwai:
"Just one commit for adding a copule of HD-audio quirk entries"
* tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add headset Mic support for new Dell machine
Pull drm intel fixes from Dave Airlie:
"Two intel stable fixes, that should be it from me for this round"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Pull ACPI backlight fix from Rafael Wysocki:
"This is a simple fix for an ACPI backlight regression introduced by a
recent commit that overlooked a corner case which should have been
taken into account"
* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: update condition to check if device is in _DOD list
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Pull media fixes from Mauro Carvalho Chehab:
"A core fix and some driver fixes:
- regression fix in Remote Controller core affecting RC6 protocol
handling
- fix video buffer handling in cx23885
- race fix in solo6x10
- fix image selection in smiapp
- fix reported payload size on s2255drv
- two updates for MAINTAINERS file"
* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: fix toggle handling in the rc6 decoder
MAINTAINERS: Update mchehab's addresses
[media] cx23885: use sg = sg_next(sg) instead of sg++
[media] s2255drv: fix payload size for JPG, MJPEG
[media] Update MAINTAINERS for solo6x10
[media] solo6x10: fix a race in IRQ handler
[media] smiapp: Only some selection targets are settable
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26 ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context. This causes RCU
warnings and possible failures.
This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c bugfixes from Wolfram Sang:
"A few driver bugfixes for 3.18"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: omap: fix i207 errata handling
i2c: designware: prevent early stop on TX FIFO empty
i2c: omap: fix NACK and Arbitration Lost irq handling
Pull PCI fix from Bjorn Helgaas:
"This fixes a Tegra20 regression that we introduced during the v3.18
merge window"
* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use physical range for I/O mapping
Pull devicetree bugfix from Grant Likely:
"One more bug fix for v3.18. I debated whether or not to send you this
merge request because we're at such a late rc. The bug isn't critical
in that there is only one system known to be affected and the patch is
easy to backport. The codepath is used by pretty much every DT based
system, so there is risk a of regression (it /should/ be safe, but
I've been bitten by stuff that should be safe before). I've had it in
linux-next for a week and haven't received any complaints.
I think it probably should just be merged right away rather than
waiting for the merge window and backporting. It does fix a real bug
and the code is theoretically safer after the change. I can't think
of any situation where it would be dangerous to reserve the DT memory
an extra time.
Summary from tag:
Single bugfix for boot failure seen in the wild. The memory reserve
code tries to be clever about reserving the FDT, but it should just
go ahead and reserve it unconditionally to avoid the problem of
partial overlap described in the patch"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap
Pull block core regression fix from Jens Axboe:
"Single fix for a regression introduced in this development cycle,
where dm on top of dif/dix is broken. From Darrick Wong"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix regression where bio_integrity_process uses wrong bio_vec iterator
Pull drm fixes from Dave Airlie:
"Radeon and Nouveau fixes:
So nouveau had a few regression introduced, Ben and Maarten finally
tracked down the one that was causing problems on my MacBookPro, also
nvidia gave some info on the an engine we were using incorrectly, so
disable our use of it, and one regresion with pci hotplug affecting
optimus users.
Radeon has an oops fixs, sync fix, and one workaround to avoid broken
functionality on 32-bit x86, this needs better root causing and a
better fix, but the bandaid is a lot safer at this point"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
nouveau: move the hotplug ignore to correct place.
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
Pull networking fixes from David Miller:
1) Fill in ethtool link parameters for all link types in cxgb4, from
Hariprasad Shenai.
2) Fix probe regressions in stmmac driver, from Huacai Chen.
3) Network namespace leaks on errirs in rtnetlink, from Nicolas
Dichtel.
4) Remove erroneous BUG check which can actually trigger legitimately,
in xen-netfront. From Seth Forshee.
5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
Thomas Grag.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
sh_eth: Fix sleeping function called from invalid context
stmmac: platform: Move plat_dat checking earlier
sh_eth: Fix skb alloc size and alignment adjust rule.
rtnetlink: release net refcnt on error in do_setlink()
bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes
Pull keyring/nfs fixes from James Morris:
"From David Howells:
The first one fixes the handling of maximum buffer size for key
descriptions, fixing the size at 4095 + NUL char rather than whatever
PAGE_SIZE happens to be and permits you to read back the full
description without it getting clipped because some extra information
got prepended.
The second and third fix a bug in NFS idmapper handling whereby a key
representing a mapping between an id and a name expires and causing
EKEYEXPIRED to be seen internally in NFS (which prevents the mapping
from happening) rather than re-looking up the mapping"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: request_key() should reget expired keys rather than give EKEYEXPIRED
KEYS: Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags
KEYS: Fix the size of the key description passed to/from userspace
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
The bounds check for nodeid in ____cache_alloc_node gives false
positives on machines where the node IDs are not contiguous, leading to
a panic at boot time. For example, on a POWER8 machine the node IDs are
typically 0, 1, 16 and 17. This means that num_online_nodes() returns
4, so when ____cache_alloc_node is called with nodeid = 16 the VM_BUG_ON
triggers, like this:
kernel BUG at /home/paulus/kernel/kvm/mm/slab.c:3079!
Call Trace:
.____cache_alloc_node+0x5c/0x270 (unreliable)
.kmem_cache_alloc_node_trace+0xdc/0x360
.init_list+0x3c/0x128
.kmem_cache_init+0x1dc/0x258
.start_kernel+0x2a0/0x568
start_here_common+0x20/0xa8
To fix this, we instead compare the nodeid with MAX_NUMNODES, and
additionally make sure it isn't negative (since nodeid is an int). The
check is there mainly to protect the array dereference in the get_node()
call in the next line, and the array being dereferenced is of size
MAX_NUMNODES. If the nodeid is in range but invalid (for example if the
node is off-line), the BUG_ON in the next line will catch that.
Fixes: 14e50c6a9b ("mm: slab: Verify the nodeid passed to ____cache_alloc_node")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).
I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost. In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten. So a failure of anon_vma_clone() will return
success since err at this point is now zero.
Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.
Fixes: ef0855d334 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: <stable@vger.kernel.org> [2.6.18+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) don't bother with ->d_time for positives - we only check it for
negatives anyway.
b) make sure to set it at unlink and rmdir time - at *that* point
soon-to-be negative dentry matches then-current directory contents
c) don't go into renaming of old alias in vfat_lookup() unless it
has the same parent (which it will, unless we are seeing corrupted
image)
[hirofumi@mail.parknet.co.jp: make change minimum, don't call d_move() for dir]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org> [3.17.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipc_addid() makes a new ipc identifier visible to everyone. New objects
start as locked, so that the caller can complete the initialization
after the call. Within struct sem_array, at least sma->sem_base and
sma->sem_nsems are accessed without any locks, therefore this approach
doesn't work.
Thus: Move the ipc_addid() to the end of the initialization.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Rik van Riel <riel@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051
[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
1. use zswap as the frontswap backend with writeback feature
2. store a swap page(version_1) to entry A, success
3. dup-store a newer page(version_2) to the same entry A, fail
4. use __swap_writepage() write version_2 page to swapfile, success
5. zswap do shrink, writeback version_1 page to swapfile
6. version_2 page is overwrited by version_1, data corrupt.
This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few more small fixes for 3.18.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
bio integrity handling is broken on a system with LVM layered atop a
DIF/DIX SCSI drive because device mapper clones the bio, modifies the
clone, and sends the clone to the lower layers for processing.
However, the clone bio has bi_vcnt == 0, which means that when the sd
driver calls bio_integrity_process to attach DIX data, the
for_each_segment_all() call (which uses bi_vcnt) returns immediately
and random garbage is sent to the disk on a disk write. The disk of
course returns an error.
Therefore, teach bio_integrity_process() to use bio_for_each_segment()
to iterate the bio_vecs, since the per-bio iterator tracks which
bio_vecs are associated with that particular bio. The integrity
handling code is effectively part of the "driver" (it's not the bio
owner), so it must use the correct iterator function.
v2: Fix a compiler warning about abandoned local variables. This
patch supersedes "block: bio_integrity_process uses wrong bio_vec
iterator". Patch applies against 3.18-rc6.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just a couple of fixes for the fallout from the fence rework.
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
Closes a very unlikely race that can occur if another NonStallInterrupt
method passes between checking fences and acking the previous interrupt.
With this change, the interrupt will re-fire under such conditions.
Tested-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull ext4 bugfix from Ted Ts'o:
"Fix an ext4 metadata checksum regression introduced in v3.18-rc3"
* tag 'ext4_for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix regression where we fail to initialize checksum seed when loading
When we're enabling journal features, we cannot use the predicate
jbd2_journal_has_csum_v2or3() because we haven't yet set the sb
feature flag fields! Moreover, we just finished loading the shash
driver, so the test is unnecessary; calculate the seed always.
Without this patch, we fail to initialize the checksum seed the first
time we turn on journal_checksum, which means that all journal blocks
written during that first mount are corrupt. Transactions written
after the second mount will be fine, since the feature flag will be
set in the journal superblock. xfstests generic/{034,321,322} are the
regression tests.
(This is important for 3.18.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.coM>
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Commit 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT. Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.
On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge. This helps to make /proc/iomem
more readable.
Combining both of the above, the union would now include the I/O space
region. This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000. Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.
This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space. This allows the translation setup within
the driver to reuse the physical addresses. The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Since the keyring facility can be viewed as a cache (at least in some
applications), the local expiration time on the key should probably be viewed
as a 'needs updating after this time' property rather than an absolute 'anyone
now wanting to use this object is out of luck' property.
Since request_key() is the main interface for the usage of keys, this should
update or replace an expired key rather than issuing EKEYEXPIRED if the local
expiration has been reached (ie. it should refresh the cache).
For absolute conditions where refreshing the cache probably doesn't help, the
key can be negatively instantiated using KEYCTL_REJECT_KEY with EKEYEXPIRED
given as the error to issue. This will still cause request_key() to return
EKEYEXPIRED as that was explicitly set.
In the future, if the key type has an update op available, we might want to
upcall with the expired key and allow the upcall to update it. We would pass
a different operation name (the first column in /etc/request-key.conf) to the
request-key program.
request_key() returning EKEYEXPIRED is causing an NFS problem which Chuck
Lever describes thusly:
After about 10 minutes, my NFSv4 functional tests fail because the
ownership of the test files goes to "-2". Looking at /proc/keys
shows that the id_resolv keys that map to my test user ID have
expired. The ownership problem persists until the expired keys are
purged from the keyring, and fresh keys are obtained.
I bisected the problem to 3.13 commit b2a4df200d ("KEYS: Expand
the capacity of a keyring"). This commit inadvertantly changes the
API contract of the internal function keyring_search_aux().
The root cause appears to be that b2a4df200d made "no state check"
the default behavior. "No state check" means the keyring search
iterator function skips checking the key's expiry timeout, and
returns expired keys. request_key_and_link() depends on getting
an -EAGAIN result code to know when to perform an upcall to refresh
an expired key.
This patch can be tested directly by:
keyctl request2 user debug:fred a @s
keyctl timeout %user:debug:fred 3
sleep 4
keyctl request2 user debug:fred a @s
Without the patch, the last command gives error EKEYEXPIRED, but with the
command it gives a new key.
Reported-by: Carl Hetherington <cth@carlh.net>
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags to be two variations of the
same flag. They are effectively mutually exclusive and one or the other
should be provided, but not both.
Keyring cycle detection and key possession determination are the only things
that set NO_STATE_CHECK, except that neither flag really does anything there
because neither purpose makes use of the keyring_search_iterator() function,
but rather provides their own.
For cycle detection we definitely want to check inside of expired keyrings,
just so that we don't create a cycle we can't get rid of. Revoked keyrings
are cleared at revocation time and can't then be reused, so shouldn't be a
problem either way.
For possession determination, we *might* want to validate each keyring before
searching it: do you possess a key that's hidden behind an expired or just
plain inaccessible keyring? Currently, the answer is yes. Note that you
cannot, however, possess a key behind a revoked keyring because they are
cleared on revocation.
keyring_search() sets DO_STATE_CHECK, which is correct.
request_key_and_link() currently doesn't specify whether to check the key
state or not - but it should set DO_STATE_CHECK.
key_get_instantiation_authkey() also currently doesn't specify whether to
check the key state or not - but it probably should also set DO_STATE_CHECK.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When a key description argument is imported into the kernel from userspace, as
happens in add_key(), request_key(), KEYCTL_JOIN_SESSION_KEYRING,
KEYCTL_SEARCH, the description is copied into a buffer up to PAGE_SIZE in size.
PAGE_SIZE, however, is a variable quantity, depending on the arch. Fix this at
4096 instead (ie. 4095 plus a NUL termination) and define a constant
(KEY_MAX_DESC_SIZE) to this end.
When reading the description back with KEYCTL_DESCRIBE, a PAGE_SIZE internal
buffer is allocated into which the information and description will be
rendered. This means that the description will get truncated if an extremely
long description it has to be crammed into the buffer with the stringified
information. There is no particular need to copy the description into the
buffer, so just copy it directly to userspace in a separate operation.
Reported-by: Christian Kastner <debian@kvr.at>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Christian Kastner <debian@kvr.at>
Commit eb7e7d76 "s390: Replace __get_cpu_var uses" broke machine check
handling.
We copy machine check information from per-cpu to a stack variable for
local processing. Next we should zap the per-cpu variable, not the
stack variable.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
First, there was this: https://bugzilla.kernel.org/show_bug.cgi?id=88001
The problem there was that microcode patches are not being reapplied
after suspend-to-ram. It was important to reapply them, though, because
of for example Haswell's TSX erratum which disabled TSX instructions
with a microcode patch.
A simple fix was fb86b97300 ("x86, microcode: Update BSPs microcode
on resume") but, as it is often the case, simple fixes are too
simple. This one causes 32-bit resume to fail:
https://bugzilla.kernel.org/show_bug.cgi?id=88391
Properly fixing this would require more involved changes for which it
is too late now, right before the merge window. Thus, limit this to
64-bit only temporarily.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1417353999-32236-1-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 0b8db271f1 ("ACPI / video: check _DOD list when creating
backlight devices") checks if the video device is in the bind devices
list to decide if we should create backlight device for it, that causes
problem for one Dell Latitude E6410, where none of the video output
devices are properly bound due to the way how we did the comparing
between its _ADR and the _DOD's values. Solve this problem by comparing
the lower 12 bits of both the device's _ADR and the _DOD's values instead
of relying on bind result.
Fixes: 0b8db271f1 ("ACPI / video: check _DOD list when creating backlight devices")
Reported-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull drm fixes from Dave Airlie:
"Two i915 regressions and one dual-gpu laptop radeon fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: report disconnected for LVDS/eDP with PX if ddc fails
drm/i915: Cancel vdd off work before suspend
drm/i915: Ignore SURFLIVE and flip counter when the GPU gets reset
Don Bailey noticed that our page zeroing for compression at end-io time
isn't complete. This reworks a patch from Linus to push the zeroing
into the zlib and lzo specific functions instead of trying to handle the
corners inside btrfs_decompress_buf2page
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reported-by: Don A. Bailey <donb@securitymouse.com>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original code only check/alloc plat_dat for the CONFIG_OF case, this
patch check/alloc it earlier and unconditionally to avoid kernel build
warnings:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:275
stmmac_pltfr_probe() warn: variable dereferenced before check 'plat_dat'
V2: Fix coding style.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d7 ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
"Three fixlets from the ARM SoC camp:
- correct irqdomain initialization for atmel-aic
- correct error handling for device tree parsing in bcm controllers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: brcmstb-l2: Fix error handling of irq_of_parse_and_map
irqchip: bcm7120-l2: Fix error handling of irq_of_parse_and_map
irqchip: atmel-aic: Fix irqdomain initialization
Pull SCSI fixes from James Bottomley:
"This is a set of ten fixes: 8 for UFS including four static checker
warnings, a potential null deref in the voltage regulator code, a race
on module unload, a ref counting fix on the well known LUNs which made
it impossible to remove the ufs module and fix to correct the
information in pwr_info.
In addition to UFS, there's a blacklist for the Intel Multi-Flex array
which chokes on report supported operation codes and a fix to an oops
in bnx2fc caused by shared skbs"
[ For us non-SCSI people: "UFS" here is "Universal Flash Storage" not
the filesystem. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ufs: fix NULL dereference when no regulators are defined
ufs: ensure clk gating work is finished before module unloading
scsi: ufs: fix static checker warning in ufshcd_parse_clock_info
scsi: ufs: fix static checker warning in __ufshcd_setup_clocks
scsi: ufs: fix static checker warning in ufshcd_populate_vreg
scsi: ufs: fix static checker errors in ufshcd_system_suspend
ufs: fix power info after link start-up
ufs: fix reference counting of W-LUs
scsi: add Intel Multi-Flex to scsi scan blacklist
bnx2fc: do not add shared skbs to the fcoe_rx_list
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
Pull tty/serial fix from Greg KH:
"Here is a single revert for the of-serial driver that resolves a
reported issue.
This revert has been in linux-next for a while"
* tag 'tty-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: of-serial: add PM suspend/resume support"
Pull USB fixes from Greg KH:
"Here are some USB driver fixes and new device ids for 3.18-rc7.
Full details are in the shortlog, and all of these have been in the
linux-next tree for a while"
* tag 'usb-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000
usb: xhci: rework root port wake bits if controller isn't allowed to wakeup
USB: xhci: Reset a halted endpoint immediately when we encounter a stall.
Revert "xhci: clear root port wake on bits if controller isn't wake-up capable"
USB: xhci: don't start a halted endpoint before its new dequeue is set
USB: uas: Add no-uas quirk for Hitachi usb-3 enclosures 4971:1012
USB: ssu100: fix overrun-error reporting
USB: keyspan: fix overrun-error reporting
USB: keyspan: fix tty line-status reporting
usb: serial: ftdi_sio: add PIDs for Matrix Orbital products
usb: dwc3: ep0: fix for dead code
USB: serial: cp210x: add IDs for CEL MeshConnect USB Stick
Pull thermal fixes from Eduardo Valentin:
"In this -rc still very minor changes:
- Lee Jones fixes compilation warning in sti thermal driver
- Marjus Elfring removes unnecessary checks in exynos thermal driver
(as per coccinelle)
- Now we always update cpufreq policies, and thus get (hopefully)
always in sync with cpufreq, thanks to Yadwinder"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: Exynos: Deletion of unnecessary checks before two function calls
thermal: sti: Ignore suspend/resume functions when !PM_SLEEP
thermal: cpu_cooling: Update always cpufreq policy with thermal constraints
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
Pull ARM SoC fixes from Arnd Bergmann:
"Not much interesting going on fixes-wise for us this week, as it
should be for an -rc7. I'm not expecting Olof to work much over
Thanksgiving weekend, so I decided to take over again and push these
out to you.
Just four simple fixes this week:
- one missing of_node_put() on armv7 based mvebu
- forcing the USB host into the right mode on Chromebook
(exynos5-snow)
- enabling two important drivers for exynos_defconfig
- fixing a noncritical bug for tegra that would cause a regression
with common code patches queued for 3.19"
* tag 'armsoc-for-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: irq: fix buggy usage of irq_data irq field
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
ARM: dts: Explicitly set dr_mode on exynos5250-snow
ARM: mvebu: add missing of_node_put() call in coherency.c
Pull ARM fixes from Russell King:
"Another round of relatively small ARM fixes.
Thomas spotted that the strex backoff delay bit was a disable bit, so
it needed to be clear for this to work. Vladimir spotted that using a
restart block for the cache flush operation would return -EINTR, which
userspace was not expecting. Dmitry spotted that the auxiliary
control register accesses for Xscale were not correct"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8226/1: cacheflush: get rid of restarting block
ARM: 8222/1: mvebu: enable strex backoff delay
ARM: 8216/1: xscale: correct auxiliary register in suspend/resume
Two regression fixes from Ville.
* tag 'drm-intel-fixes-2014-11-27' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Cancel vdd off work before suspend
drm/i915: Ignore SURFLIVE and flip counter when the GPU gets reset
Pull mips fixes from Ralf Baechle:
"The hopefully final round of fixes for 3.18:
- Fix a number of build errors affecting particular configurations.
- Handle EVA correctly when flushing a signal trampoline and dcache
lines.
- Fix printks printing jibberish.
- Handle 64 bit memory addresses correctly when adding memory chunk
on 32 bit kernels.
- Fix a race condition in the hardware tablewalker code"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: tlbex: Fix potential HTW race on TLBL/M/S handlers
MIPS: Fix address type used for early memory detection.
MIPS: Kconfig: Don't allow both microMIPS and SmartMIPS to be selected.
MIPS: kernel: cps-vec: Set ISA level to mips32r2 for the MIPS MT ASE
MIPS: Netlogic: handle modular AHCI builds
MIPS: Netlogic: handle modular USB case
MIPS: Loongson: Make platform serial setup always built-in.
MIPS: fix EVA & non-SMP non-FPU FP context signal handling
MIPS: cpu-probe: Set the FTLB probability bit on supported cores
MIPS: BMIPS: Fix ".previous without corresponding .section" warnings
MIPS: uaccess.h: Fix strnlen_user comment.
MIPS: r4kcache: Add EVA case for protected_writeback_dcache_line
MIPS: Fix info about plat_setup in arch_mem_init comment
MIPS: rtlx: Remove KERN_DEBUG from pr_debug() arguments in rtlx.c
MIPS: SEAD3: Fix LED device registration.
MIPS: Fix a copy & paste error in unistd.h
Pull powerpc fixes from Michael Ellerman:
"Here are five fixes for you to pull please.
They're all CC'ed to stable except the "Fix PE state format" one which
went in this release"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: 32 bit getcpu VDSO function uses 64 bit instructions
powerpc/powernv: Replace OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE
powerpc/eeh: Fix PE state format
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
powerpc/powernv: Fix the hmi event version check.
Pull sparc fixlet from David Miller:
"Aparc fix to add dma_cache_sync(), even if a nop it should be provided
if dma_{alloc,free}_noncoherent() is provided too"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Add NOP dma_cache_sync() implementation.
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
Pull spi fixes from Mark Brown:
"There's a couple of driver fixes here, plus one core fix for the DMA
mapping which wasn't doing the right thing for vmalloc()ed addresses
that hadn't been through kmap(). It's fairly rare to use vmalloc()
with SPI and it's a subset of those users who might fail so it's
unsurprising that this wasn't noticed sooner"
* tag 'spi-v3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sirf: fix word width configuration
spi: Fix mapping from vmalloc-ed buffer to scatter list
spi: dw: Fix dynamic speed change.
Pull input layer fixes from Dmitry Torokhov:
"The main change is to fix breakage in Elantech driver introduced by
the recent commit adding trackpoint reporting to protocol v4. Now we
are trusting the hardware to advertise the trackpoint properly and do
not try to decode the data as trackpoint if firmware told us it is not
present"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - use proper endpoint type
Input: elantech - trust firmware about trackpoint presence
Input: synaptics - adjust min/max on Thinkpad E540
There is a potential race when probing the TLB in TLBL/M/S exception
handlers for a matching entry. Between the time we hit a TLBL/S/M
exception and the time we get to execute the TLBP instruction, the
HTW may have replaced the TLB entry we are interested in hence the TLB
probe may fail. However, in the existing handlers, we never checked the
status of the TLBP (ie check the result in the C0/Index register). We
fix this by adding such a check when the core implements the HTW. If
we couldn't find a matching entry, we return back and try again.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f ("arm: mm: Add support for PJ4B cpu and init routines")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull "Samsung defconfig update for v3.18" from Kukjin Kim:
- enable max77802 rtc and clock drivers for exynos_defconfig
: enable the kernel config options to have the drivers for
max77802 including rtc and 2-ch 32kHz clock outputs
* tag 'samsung-defconfig-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The crazy gic_arch_extn thing that Tegra uses contains multiple
references to the irq field in struct irq_data, and uses this
to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 25801 2075 GIC 29 twd
17: 0 0 GIC 73 timer0
112: 0 0 GPIO 58 c8000600.sdhci cd
123: 0 0 GPIO 69 c8000200.sdhci cd
279: 1126 0 GIC 122 serial
281: 0 0 GIC 70 7000c000.i2c
282: 0 0 GIC 116 7000c400.i2c
283: 0 0 GIC 124 7000c500.i2c
284: 300 0 GIC 85 7000d000.i2c
[...]
Just replacing all instances of irq with hwirq fixes the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
one fix for PX laptops.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: report disconnected for LVDS/eDP with PX if ddc fails
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd34 ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flag passed to ioda_eeh_phb_reset() should be EEH_RESET_DEACTIVATE,
which is translated to OPAL_DEASSERT_RESET or something else by the
EEH backend accordingly.
The patch replaces OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE for
ioda_eeh_phb_reset().
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce. The patch fixes it up.
Fixes: 2013add4ce ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [c0000003f39ffb10]
pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp: c0000003f39ffc70
msr: 8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40]
pc: 000000000eca7cc4
lr: 000000000eca7c44
sp: fafb4b0
msr: 8000000000001000
dar: 10000000
dsisr: 42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current HMI event structure is an ABI and carries a version field to
accommodate future changes without affecting/rearranging current structure
members that are valid for previous versions.
The current version check "if (hmi_evt->version != OpalHMIEvt_V1)"
doesn't accomodate the fact that the version number may change in
future.
If firmware starts returning an HMI event with version > 1, this check
will fail and no HMI information will be printed on older kernels.
This patch fixes this issue.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Reword changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit fadbe0cd52 entitled "staging:
rtl8188eu:Remove rtw_zmalloc(), wrapper for kzalloc()", the author failed
to note that the original code in the wrapper tested whether the caller
could sleep, and set the flags argument to kzalloc() appropriately.
After the patch, GFP_KERNEL is used unconditionally. Unfortunately, several
of the routines may be entered from an interrupt routine and generate
a BUG splat for every such call. Routine rtw_sitesurvey_cmd() is used in the
example below:
BUG: sleeping function called from invalid context at mm/slub.c:1240
in_atomic(): 1, irqs_disabled(): 0, pid: 756, name: wpa_supplicant
INFO: lockdep is turned off.
CPU: 2 PID: 756 Comm: wpa_supplicant Tainted: G WC O 3.18.0-rc4+ #34
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
ffffc90005557000 ffff880216fafaa8 ffffffff816b0bbf 0000000000000000
ffff8800c3b58000 ffff880216fafac8 ffffffff8107af77 0000000000000001
0000000000000010 ffff880216fafb18 ffffffff811b06ce 0000000000000000
Call Trace:
[<ffffffff816b0bbf>] dump_stack+0x4e/0x71
[<ffffffff8107af77>] __might_sleep+0xf7/0x120
[<ffffffff811b06ce>] kmem_cache_alloc_trace+0x4e/0x1f0
[<ffffffffa0888226>] ? rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa0888226>] rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa088f00d>] rtw_do_join+0x22d/0x370 [r8188eu]
[<ffffffffa088f6e8>] rtw_set_802_11_ssid+0x218/0x3d0 [r8188eu]
[<ffffffffa08c3ca5>] rtw_wx_set_essid+0x1e5/0x410 [r8188eu]
[<ffffffffa08c3ac0>] ? rtw_wx_get_rate+0x50/0x50 [r8188eu]
[<ffffffff816938f1>] ioctl_standard_iw_point+0x151/0x3f0
[<ffffffff81693d52>] ioctl_standard_call+0xb2/0xe0
[<ffffffff81597df7>] ? rtnl_lock+0x17/0x20
[<ffffffff816945a0>] ? iw_handler_get_private+0x70/0x70
[<ffffffff81693ca0>] ? call_commit_handler+0x40/0x40
[<ffffffff81693256>] wireless_process_ioctl+0x176/0x1c0
[<ffffffff81693e79>] wext_handle_ioctl+0x69/0xc0
[<ffffffff8159fe79>] dev_ioctl+0x309/0x5e0
[<ffffffff810be9c7>] ? call_rcu+0x17/0x20
[<ffffffff8156a472>] sock_ioctl+0x142/0x2e0
[<ffffffff811e0c70>] do_vfs_ioctl+0x300/0x520
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff810102bc>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff811e0f11>] SyS_ioctl+0x81/0xa0
[<ffffffff816ba1d2>] system_call_fastpath+0x12/0x17
Additional routines that generate this BUG are rtw_joinbss_cmd(),
rtw_dynamic_chk_wk_cmd(), rtw_lps_ctrl_wk_cmd(), rtw_rpt_timer_cfg_cmd(),
rtw_ps_cmd(), report_survey_event(), report_join_res(), survey_timer_hdl(),
and rtw_check_bcn_info().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: navin patidar <navin.patidar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John W. Linville says:
====================
pull request: wireless 2014-11-26
Please pull this little batch of fixes intended for the 3.18 stream...
For the iwlwifi one, Emmanuel says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Along with that, Larry sends a pair of rtlwifi fixes to address some
discrepancies from moving drivers out of staging. Larry says:
"These two patches are needed to fix a regression introduced when
driver rtl8821ae was moved from staging to the regular wireless tree."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf says:
====================
bridge: Fix missing Netlink message validations
Adds various missing length checks in the bridging code for Netlink
messages and corresponding attributes provided by user space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kvm fixes from Paolo Bonzini:
"Last minute KVM/ARM fixes; even the generic change actually affects
nothing but ARM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: fix kvm_is_mmio_pfn() and rename to kvm_is_reserved_pfn()
arm/arm64: kvm: drop inappropriate use of kvm_is_mmio_pfn()
arm/arm64: KVM: vgic: Fix error code in kvm_vgic_create()
arm64: KVM: Handle traps of ICC_SRE_EL1 as RAZ/WI
arm64: KVM: fix unmapping with 48-bit VAs
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
The commit 3b57de958e brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: misc bugfixes
This patch series contains two bug fixes:
- first patch fixes an issue on the error path of the driver where we could
have left some of our registers mapped
- second patch enforces the use of a software reset of the switch to guarantee
the HW is in a consistent state prior to software initialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using kvm_is_mmio_pfn() to decide whether a host region
should be stage 2 mapped with device attributes, add a new static
function kvm_is_device_pfn() that disregards RAM pages with the
reserved bit set, as those should usually not be mapped as device
memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we detect another vCPU is running we just exit and return 0 as if we
succesfully created the VGIC, but the VGIC wouldn't actual be created.
This shouldn't break in-kernel behavior because the kernel will not
observe the failed the attempt to create the VGIC, but userspace could
be rightfully confused.
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When running on a system with a GICv3, we currenly don't allow the guest
to access the system register interface of the GICv3. We do this by
clearing the ICC_SRE_EL2.Enable, which causes all guest accesses to
ICC_SRE_EL1 to trap to EL2 and causes all guest accesses to other ICC_
registers to cause an undefined exception in the guest.
However, we currently don't handle the trap of guest accesses to
ICC_SRE_EL1 and will spill out a warning. The trap just needs to handle
the access as RAZ/WI, and a guest that tries to prod this register and
set ICC_SRE_EL1.SRE=1, must read back the value (which Linux already
does) to see if it succeeded, and will thus observe that ICC_SRE_EL1.SRE
was not set.
Add the simple trap handler in the sorted table of the system registers.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[ardb: added cp15 handling]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
memblock_is_region_reserved() returns true in the case of a partial
overlap, meaning that the current code fails to reserve the
non-overlapping portion.
This call was introduced as part of d1552ce449 "of/fdt: move
memreserve and dtb memory reservations into core" which went into
v3.16.
I observed this causing a Midway system with a buggy fdt (the header
declares itself to be larger than it really is) failing to boot
because the over-inflated size of the fdt was causing it to seem to
run into the swapper_pg_dir region, meaning the DT wasn't reserved.
The symptoms were failing to find an disks or network and failing to
boot.
However given the ambiguity of whether things like the initrd are
covered by /memreserve/ and similar I think it is best to also
register the region rather than just ignoring it.
Since memblock_reserve() handles overlaps just fine lets just warn and
carry on.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # v3.16+
Currently we just make sure vdd is off before suspending, but we don't
cancel the vdd off work. The work wil not touch vdd if
want_panel_vdd==false so in theory this is fine.
In the past that was perfectly fine since the vdd off work didn't do
anything when want_panel_vdd==false, so even if the work would have been
run during system resume before i915 has resumed, nothing would happen.
However since pps_lock() will now grab the power domain references before
it can check want_panel_vdd, we may end up toggling the power wells on/off
already before the driver has resumed. That is not really acceptable, so
cancel the vdd off work when suspending the encoder.
The problem appeared when pps_lock() was introduced in:
commit 773538e860
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:56 2014 +0300
drm/i915: Reset power sequencer pipe tracking when disp2d is off
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If no voltage supply regulators are defined for the UFS devices (assumed
they are always-on), ufshcd_config_vreg_load() can be called on
suspend/resume paths with vreg == NULL as hba->vreg_info.vcc* equal to
NULL, and it causes NULL pointer dereference.
This fixes it by making ufshcd_config_vreg_{h,l}pm noop when no regulators
are defined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When dynamic clk gating feature is enabled, delayed workqueue machanism
is used in order to detect certain period of inactivity. But there is no
guarantee that scheduled gating work is completed before module unloading.
So it can cause kernel crash by accessing memory after it was freed.
Fix it by cancelling clk gating and ungating works and ensure that its
execution is finished before module unloading.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull nfsd bugfixes from Bruce Fields:
"These fix one mishandling of the case when security labels are
configured out, and two races in the 4.1 backchannel code"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix slot wake up race in the nfsv4.1 callback code
SUNRPC: Fix locking around callback channel reply receive
nfsd: correctly define v4.2 support attributes
Pull aio fix from Ben LaHaise:
"Dirty page accounting fix for aio"
* git://git.kvack.org/~bcrl/aio-fixes:
aio: fix uncorrent dirty pages accouting when truncating AIO ring buffer
Pull powerpc fixes from Ben Herrenschmidt:
"This series fix a nasty issue with radeon adapters on powerpc servers,
it's all CC'ed stable and has the relevant maintainers ack's/reviews.
Basically, some (radeon) adapters have issues with MSI addresses above
1T (only support 40-bits). We had powerpc specific quirk but it only
listed a specific revision of an adapter that we shipped with our
machines and didn't properly handle the audio function which some
distros enable nowadays.
So we made the quirk generic and fixed both the graphic and audio
drivers properly to use it.
Without that, ppc64 server machines will crash at boot with a radeon
adapter.
Note: This has been brewing for a while, it just needed a last respin
which got delayed due to us moving ozlabs to a new location in town
and other such things taking priority"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Remove unused force_32bit_msi quirk
powerpc/pseries: Honor the generic "no_64bit_msi" flag
powerpc/powernv: Honor the generic "no_64bit_msi" flag
sound/radeon: Move 64-bit MSI quirk from arch to driver
gpu/radeon: Set flag to indicate broken 64-bit MSI
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
Pull a hwmon fix from Guenter Roeck:
"Fix hwmon registration problem in g762 driver"
* tag 'hwmon-for-linus-v3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (g762) fix call to devm_hwmon_device_register_with_groups()
Pull clock fixes from Mike Turquette:
"The fixes for the clock framework are all regressions in drivers, plus
a single fix in one of the basic clock templates. No fixes to the
core this time around.
As with most clock driver fixes these run the gamut from fixing a
build warning to fixing wrecked memory timings, with a little USB
tossed in for fun"
* tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux:
clk: pxa: fix pxa27x CCCR bit usage
clk-divider: Fix READ_ONLY when divider > 1
clk: qcom: Fix duplicate rbcpr clock name
clk: at91: usb: fix at91sam9x5 recalc, round and set rate
clk: at91: usb: fix at91rm9200 round and set rate
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ca777eff51 ("tcp: remove dst refcount false sharing for
prequeue mode") we have to relax check against skb dst in
tcp_v[46]_send_reset() if prequeue dropped the dst.
If a socket is provided, a full lookup was done to find this socket,
so the dst test can be skipped.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88191
Reported-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: ca777eff51 ("tcp: remove dst refcount false sharing for prequeue mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5195c14c8b.
If the conntrack clashes with an existing one, it is left out of
the unconfirmed list, thus, crashing when dropping the packet and
releasing the conntrack since golden rule is that conntracks are
always placed in any of the existing lists for traceability reasons.
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=88841
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Fix outer UDP checksums for IPv6 VXLAN tunnels
In testing against an older kernel I found a couple issues in the IPv6
VXLAN tunnel checksum logic for the outer UDP checksum.
First the default transitioned from using an outer checksum to not using
one. Second, sometime after that the checksum inputs were changed
resulting the checksum not being correct if it were computed.
These two issues prevented a ping from the newer kernel to the older one.
With these two changes applied I verified I was able to send traffic over
the VXLAN tunnel to a link partner on an older kernel.
The boolean flip fix can be submitted for 3.17 stable as well since the
patch that introduced the issue was included in that kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In "vxlan: Call udp_sock_create" there was a logic error that resulted in
the default for IPv6 VXLAN tunnels going from using checksums to not using
checksums. Since there is currently no support in iproute2 for setting
these values it means that a kernel after the change cannot talk over a IPv6
VXLAN tunnel to a kernel prior the change.
Fixes: 3ee64f3 ("vxlan: Call udp_sock_create")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP checksum calculation for VXLAN tunnels is currently using the
socket addresses instead of the actual packet source and destination
addresses. As a result the checksum calculated is incorrect in some
cases.
Also uh->check was being set twice, first it was set to 0, and then it is
set again in udp6_set_csum. This change removes the redundant assignment
to 0.
Fixes: acbf74a7 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions.")
Cc: Andy Zhou <azhou@nicira.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Only try to parse data as coming from trackpoint if firmware told us that
trackpoint is present.
Fixes commit caeb0d37fa
Reported-and-tested-by: Marcus Overhagen <marcus.overhagen@gmail.com>
Reported-and-tested-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
af_packet produces lots of these:
net/packet/af_packet.c:384:39: warning: incorrect type in return expression (different modifiers)
net/packet/af_packet.c:384:39: expected struct page [pure] *
net/packet/af_packet.c:384:39: got struct page *
this seems to be because sparse does not realize that _pure
refers to function, not the returned pointer.
Tweak code slightly to avoid the warning.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If xenvif_alloc() or xenbus_scanf() fail in backend_create_xenvif(),
xenbus is left in offline mode but netback_probe() reports success.
The patch implements propagation of error code for backend_create_xenvif().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a GPU reset we need to get pending page flip cleared out
since the ring contents are gone and flip will never complete
on its own. This used to work until the mmio vs. CS flip race
detection came about. That piece of code is looking for a
specific surface address in the SURFLIVE register, but as
a flip to that address may never happen the check may never
pass. So we should just skip the SURFLIVE and flip counter
checks when the GPU gets reset.
intel_display_handle_reset() tries to effectively complete
the flip anyway by calling .update_primary_plane(). But that
may not satisfy the conditions of the mmio vs. CS race
detection since there's no guarantee that a modeset didn't
sneak in between the GPU reset and intel_display_handle_reset().
Such a modeset will not wait for pending flips due to the ongoing GPU
reset, and then the primary plane updates performed by
intel_display_handle_reset() will already use the new surface
address, and thus the surface address the flip is waiting for
might never appear in SURFLIVE. The result is that the flip
will never complete and attempts to perform further page flips
will fail with -EBUSY.
During the GPU reset intel_crtc_has_pending_flip() will return
false regardless, so the deadlock with a modeset vs. the error
work acquiring crtc->mutex was avoided. And the reset_counter
check in intel_crtc_has_pending_flip() actually made this bug
even less severe since it allowed normal modesets to go through
even though there's a pending flip.
This is a regression introduced by me here:
commit 75f7f3ec60
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Apr 15 21:41:34 2014 +0300
drm/i915: Fix mmio vs. CS flip race on ILK+
Testcase: igt/kms_flip/flip-vs-panning-vs-hang
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
microMIPS and SmartMIPS can't be used together. This fixes the
following build problem:
Warning: the 32-bit microMIPS architecture does not support the `smartmips' extension
arch/mips/kernel/entry.S:90: Error: unrecognized opcode `mtlhx $24'
[...]
arch/mips/kernel/entry.S:109: Error: unrecognized opcode `mtlhx $24'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commits a951440971 ("MIPS: Netlogic: Support for XLP3XX on-chip SATA")
and fedfcb1137 ("MIPS: Netlogic: XLP9XX on-chip SATA support") added
ahci-init and ahci-init-xlp2 as objects to build when CONFIG_SATA_AHCI
is enabled.
If CONFIG_SATA_AHCI is made modular, these two files will also get built
as modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/ahci-init.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack"
[arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
Just check whether CONFIG_SATA_AHCI is defined for this build, and if
that is the case, add these objects to the list of built-in object
files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1004165f34 ("MIPS: Netlogic: USB support for XLP") and then
commit 9eac3591e7 ("MIPS: Netlogic: Add support for USB on XLP2xx")
added usb-init and usb-init-xlp2 as objects to build when CONFIG_USB is
enabled.
If CONFIG_USB is made modular, these two files will also get built as
modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/usb-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
Just check whether CONFIG_USB is defined for this build, and if that is
the case, add these objects to the list of built-in object files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7854/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The save_fp_context & restore_fp_context pointers were being assigned
to the wrong variables if either:
- The kernel is configured for UP & runs on a system without an FPU,
since b2ead52828 "MIPS: Move & rename
fpu_emulator_{save,restore}_context".
- The kernel is configured for EVA, since ca750649e0 "MIPS: kernel:
signal: Prevent save/restore FPU context in user memory".
This would lead to FP context being clobbered incorrectly when setting
up a sigcontext, then the garbage values being saved uselessly when
returning from the signal.
Fix by swapping the pointer assignments appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8230/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the Config6/FLTBP bit to set the probability of a TLBWR
instruction to hit the FTLB or the VTLB. A value of 0 (which may be
the default value on certain cores, such as proAptiv or P5600)
means that a TLBWR instruction will never hit the VTLB which
leads to performance limitations since it effectively decreases
the number of available TLB slots.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8368/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit de8974e3f7 ("MIPS: asm: r4kcache: Add EVA cache flushing
functions") added cache function for EVA using the cachee instruction.
However, it didn't add a case for the protected_writeback_dcache_line.
mips_dsemul() calls r4k_flush_cache_sigtramp() which in turn uses
the protected_writeback_dcache_line() to flush the trampoline code
back to memory. This used the wrong "cache" instruction leading to
random userland crashes on non-FPU cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is now fully replaced with the generic "no_64bit_msi" one
that is set by the respective drivers directly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
A number of radeon cards have a HW limitation causing them to be
unable to generate the full 64-bit of address bits for MSIs. This
breaks MSIs on some platforms such as POWER machines.
We used to have a powerpc specific quirk to address that on a
single card, but this doesn't scale very well, this is better
put under control of the drivers who know precisely what a given
HW revision can do.
We now have a generic quirk in the PCI code. We should set it
appropriately for all radeon's from the audio driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
Some radeon ASICs don't support all 64 address bits of MSIs despite
advertising support for 64-bit MSIs in their configuration space.
This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can
be assigned with some of the high address bits set.
This makes use of the newly introduced "no_64bit_msi" flag in structure
pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs
on those adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
---
Adding Alex's review tag. Patch to the driver is identical to the
reviewed one, I dropped the arch/powerpc hunk rewrote the subject
and cset comment.
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():
hlist_for_each_entry_rcu(t, head, hash_node) {
if (local == t->parms.iph.saddr &&
remote == t->parms.iph.daddr &&
link == t->parms.link &&
==> type == t->dev->type &&
ip_tunnel_key_match(&t->parms, flags, key))
break;
}
the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD b2c21067 PUD b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008] ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008] ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008] ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008] [<ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008] [<ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008] [<ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008] [<ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008] [<ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008] [<ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008] [<ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008] [<ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008] [<ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008] [<ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008] [<ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....
modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti
do that one or more times, kernel will panic.
fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris bisected a NULL pointer deference in task_sched_runtime() to
commit 6e998916df 'sched/cputime: Fix clock_nanosleep()/clock_gettime()
inconsistency'.
Chris observed crashes in atop or other /proc walking programs when he
started fork bombs on his machine. He assumed that this is a new exit
race, but that does not make any sense when looking at that commit.
What's interesting is that, the commit provides update_curr callbacks
for all scheduling classes except stop_task and idle_task.
While nothing can ever hit that via the clock_nanosleep() and
clock_gettime() interfaces, which have been the target of the commit in
question, the author obviously forgot that there are other code paths
which invoke task_sched_runtime()
do_task_stat(()
thread_group_cputime_adjusted()
thread_group_cputime()
task_cputime()
task_sched_runtime()
if (task_current(rq, p) && task_on_rq_queued(p)) {
update_rq_clock(rq);
up->sched_class->update_curr(rq);
}
If the stats are read for a stomp machine task, aka 'migration/N' and
that task is current on its cpu, this will happily call the NULL pointer
of stop_task->update_curr. Ooops.
Chris observation that this happens faster when he runs the fork bomb
makes sense as the fork bomb will kick migration threads more often so
the probability to hit the issue will increase.
Add the missing update_curr callbacks to the scheduler classes stop_task
and idle_task. While idle tasks cannot be monitored via /proc we have
other means to hit the idle case.
Fixes: 6e998916df 'sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency'
Reported-by: Chris Mason <clm@fb.com>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge x86-64 iret fixes from Andy Lutomirski:
"This addresses the following issues:
- an unrecoverable double-fault triggerable with modify_ldt.
- invalid stack usage in espfix64 failed IRET recovery from IST
context.
- invalid stack usage in non-espfix64 failed IRET recovery from IST
context.
It also makes a good but IMO scary change: non-espfix64 failed IRET
will now report the correct error. Hopefully nothing depended on the
old incorrect behavior, but maybe Wine will get confused in some
obscure corner case"
* emailed patches from Andy Lutomirski <luto@amacapital.net>:
x86_64, traps: Rework bad_iret
x86_64, traps: Stop using IST for #SS
x86_64, traps: Fix the espfix64 #DF fixup and rewrite it in C
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aaf
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes this week:
- A set of clock fixes for shmobile platforms
- A fix for tegra that moves serial port labels to be per board.
We're choosing to merge this for 3.18 because the labels will start
being parsed in 3.19, and without this change serial port numbers
that used to be stable since the dawn of time will change numbers.
- A few other DT tweaks for Tegra.
- A fix for multi_v7_defconfig that makes it stop spewing cpufreq
errors on Arndale (Exynos)"
* tag 'armsoc-for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: fix failure setting CPU voltage by enabling dependent I2C controller
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
ARM: shmobile: r8a7740 legacy: Correct IIC0 parent clock
ARM: shmobile: r8a7740 legacy: Add missing INTCA clock for irqpin module
ARM: shmobile: r8a7790: Fix SD3CKCR address
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Pull percpu fix from Tejun Heo:
"This contains one patch to fix a race condition which can lead to
percpu_ref using a percpu pointer which is corrupted with a set DEAD
bit. The bug was introduced while separating out the ATOMIC mode flag
from the DEAD flag. The fix is pretty straight forward.
I just committed the patch to the percpu tree but am sending out the
pull request early as I'll be on vacation for a week. The patch
should be fairly safe and while the latency will be higher I'll be
checking emails"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu-ref: fix DEAD flag contamination of percpu pointer
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on a different issue, I noticed an annoying use
after free bug on my machine when unloading the ixgbe driver:
[ 8642.318797] ixgbe 0000:02:00.1: removed PHC on p2p2
[ 8642.742716] ixgbe 0000:02:00.1: complete
[ 8642.743784] BUG: unable to handle kernel paging request at ffff8807d3740a90
[ 8642.744828] IP: [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[ 8642.745886] PGD 20c6067 PUD 81c1f6067 PMD 81c15a067 PTE 80000007d3740060
[ 8642.746956] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 8642.748039] Modules linked in: [...]
[ 8642.752929] CPU: 1 PID: 1225 Comm: rmmod Not tainted 3.18.0-rc2+ #49
[ 8642.754203] Hardware name: Supermicro X10SLM-F/X10SLM-F, BIOS 1.1b 11/01/2013
[ 8642.755505] task: ffff8807e34d3fe0 ti: ffff8807b7204000 task.ti: ffff8807b7204000
[ 8642.756831] RIP: 0010:[<ffffffffa01c77dc>] [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[...]
[ 8642.774335] Stack:
[ 8642.775805] ffff8807ee824098 ffff8807ee824098 ffffffffa01f3000 ffff8807ee824000
[ 8642.777326] ffff8807b7207e18 ffffffff8137720f ffff8807ee824098 ffff8807ee824098
[ 8642.778848] ffffffffa01f3068 ffff8807ee8240f8 ffff8807b7207e38 ffffffff8144180f
[ 8642.780365] Call Trace:
[ 8642.781869] [<ffffffff8137720f>] pci_device_remove+0x3f/0xc0
[ 8642.783395] [<ffffffff8144180f>] __device_release_driver+0x7f/0xf0
[ 8642.784876] [<ffffffff814421f8>] driver_detach+0xb8/0xc0
[ 8642.786352] [<ffffffff814414a9>] bus_remove_driver+0x59/0xe0
[ 8642.787783] [<ffffffff814429d0>] driver_unregister+0x30/0x70
[ 8642.789202] [<ffffffff81375c65>] pci_unregister_driver+0x25/0xa0
[ 8642.790657] [<ffffffffa01eb38e>] ixgbe_exit_module+0x1c/0xc8e [ixgbe]
[ 8642.792064] [<ffffffff810f93a2>] SyS_delete_module+0x132/0x1c0
[ 8642.793450] [<ffffffff81012c61>] ? do_notify_resume+0x61/0xa0
[ 8642.794837] [<ffffffff816d2029>] system_call_fastpath+0x12/0x17
The issue is that test_and_set_bit() done on adapter->state is being
performed *after* the netdevice has been freed via free_netdev().
When netdev is being allocated on initialization time, it allocates
a private area, here struct ixgbe_adapter, that resides after the
net_device structure. In ixgbe_probe(), the device init routine,
we set up the adapter after alloc_etherdev_mq() on the private area
and add a reference for the pci_dev as well via pci_set_drvdata().
Both in the error path of ixgbe_probe(), but also on module unload
when ixgbe_remove() is being called, commit 41c62843eb ("ixgbe:
Fix rcu warnings induced by LER") accesses adapter after free_netdev().
The patch stores the result in a bool and thus fixes above oops on my
side.
Fixes: 41c62843eb ("ixgbe: Fix rcu warnings induced by LER")
Cc: stable <stable@vger.kernel.org>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE adapter seems to require that VLAN filtering be enabled if
VMDQ or SRIOV are enabled. When those functions are disabled,
VLAN filtering may be disabled in promiscuous mode.
Prior to commit a9b8943ee1 ("ixgbe: remove vlan_filter_disable
and enable functions")
The logic was correct. However, after the commit the logic
got reversed and VLAN filtered in now turned on when VMDQ/SRIOV
is disabled.
This patch changes the condition to enable hw vlan filtered
when VMDQ or SRIOV is enabled.
Fixes: a9b8943ee1 ("ixgbe: remove vlan_filter_disable and enable functions")
Cc: stable <stable@vger.kernel.org>
CC: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SKB_GSO_TCPV4 to the list of supported GSO types handled by
the IPv6 GSO offloads. Without this change VXLAN tunnels running over IPv6
do not currently handle IPv4 TCP TSO requests correctly and end up handing
the non-segmented frame off to the device.
Below is the before and after for a simple netperf TCP_STREAM test between
two endpoints tunneling IPv4 over a VXLAN tunnel running on IPv6 on top of
a 1Gb/s network adapter.
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.29 0.88 Before
87380 16384 16384 10.03 895.69 After
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs deadlock fix from Chris Mason:
"This has a fix for a long standing deadlock that we've been trying to
nail down for a while. It ended up being a bad interaction with the
fair reader/writer locks and the order btrfs reacquires locks in the
btree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix lockups from btrfs_clear_path_blocking
While decoupling ATOMIC and DEAD flags, f47ad45784 ("percpu_ref:
decouple switching to percpu mode and reinit") updated
__ref_is_percpu() so that it only tests ATOMIC flag to determine
whether the ref is in percpu mode or not; however, while DEAD implies
ATOMIC, the two flags are set separately during percpu_ref_kill() and
if __ref_is_percpu() races percpu_ref_kill(), it may see DEAD w/o
ATOMIC. Because __ref_is_percpu() returns @ref->percpu_count_ptr
value verbatim as the percpu pointer after testing ATOMIC, the pointer
may now be contaminated with the DEAD flag.
This can be fixed by clearing the flag bits before returning the
pointer which was the fix proposed by Shaohua; however, as DEAD
implies ATOMIC, we can just test for both flags at once and avoid the
explicit masking.
Update __ref_is_percpu() so that it tests that both ATOMIC and DEAD
are clear before returning @ref->percpu_count_ptr as the percpu
pointer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-Reviewed-by: Shaohua Li <shli@kernel.org>
Link: http://lkml.kernel.org/r/995deb699f5b873c45d667df4add3b06f73c2c25.1416638887.git.shli@kernel.org
Fixes: f47ad45784 ("percpu_ref: decouple switching to percpu mode and reinit")
Pull timer fix from Thomas Gleixner:
"A single bugfix for an init order problem in the sun4i subarch
clockevents code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevent: sun4i: Fix race condition in the probe code
Pull vfs fixes from Al Viro:
"Assorted fixes, most in overlayfs land"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: ovl_dir_fsync() cleanup
ovl: update MAINTAINERS
ovl: pass dentry into ovl_dir_read_merged()
ovl: use lockless_dereference() for upperdentry
ovl: allow filenames with comma
ovl: fix race in private xattr checks
ovl: fix remove/copy-up race
ovl: rename filesystem type to "overlay"
isofs: avoid unused function warning
vfs: fix reference leak in d_prune_aliases()
commit 6d9939f651 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f651 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre 6d9939f651 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Cc: <stable@vger.kernel.org> #v2.6.35
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly, so we need to fall-back to usb-storage for these.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for v3.18-rc6
Three fixes for bugs related to TTY error reporting, which can to lead
to data being dropped by the line discipline.
Included is also some new device ids for ftdi_sio and cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull networking fixes from David Miller:
1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.
2) nf_nat_range is not fully initialized and this is copied back to
userspace, from Daniel Borkmann.
3) Fix read past end of b uffer in netfilter ipset, also from Dan
Carpenter.
4) Signed integer overflow in ipv4 address mask creation helper
inet_make_mask(), from Vincent BENAYOUN.
5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
properly describe the device's capabilities, from Joe Stringer.
6) Fix memory leaks and checksum miscalculations in openvswitch, from
Pravin B SHelar and Jesse Gross.
7) FIB rules passes back ambiguous error code for unreachable routes,
making behavior confusing for userspace. Fix from Panu Matilainen.
8) ieee802154fake_probe() doesn't release resources properly on error,
from Alexey Khoroshilov.
9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.
10) Fix access of stale slave pointers in bonding code, from Nikolay
Aleksandrov.
11) Fix stack info leak in PPP pptp code, from Mathias Krause.
12) Cure locking bug in IPX stack, from Jiri Bohac.
13) Revert SKB fclone memory freeing optimization that is racey and can
allow accesses to freed up memory, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
tcp: Restore RFC5961-compliant behavior for SYN packets
net: Revert "net: avoid one atomic operation in skb_clone()"
virtio-net: validate features during probe
cxgb4 : Fix DCB priority groups being returned in wrong order
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
openvswitch: Don't validate IPv6 label masks.
pptp: fix stack info leak in pptp_getname()
brcmfmac: don't include linux/unaligned/access_ok.h
cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
ipv6: delete protocol and unregister rtnetlink when cleanup
net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
mac80211: minstrel_ht: fix a crash in rate sorting
vxlan: Inline vxlan_gso_check().
can: m_can: update to support CAN FD features
can: m_can: fix incorrect error messages
can: m_can: add missing delay after setting CCCR_INIT bit
can: m_can: fix not set can_dlc for remote frame
can: m_can: fix possible sleep in napi poll
can: m_can: add missing message RAM initialization
...
Pull drm fixes from Dave Airlie:
"Just two radeon and two intel fixes: endian and regression fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix endian swapping in vbios fetch for tdp table
drm/radeon: disable native backlight control on pre-r6xx asics (v2)
drm/i915: Kick fbdev before vgacon
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
Pull sound fixes from Takashi Iwai:
"This batch ended up as a relatively high volume due to pending ASoC
fixes. But most of fixes there are trivial and/or device- specific
fixes and quirks, so safe to apply. The only (ASoC) core fixes are
the DPCM race fix and the machine-driver matching fix for
componentization"
* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix the mic mute led problem for Latitude E5550
ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
ASoC: sgtl5000: Fix SMALL_POP bit definition
ASoC: cs42l51: re-hook of_match_table pointer
ASoC: rt5670: change dapm routes of PLL connection
ASoC: rt5670: correct the incorrect default values
ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
ASoC: max98090: Correct pclk divisor settings
ASoC: dpcm: Fix race between FE/BE updates and trigger
ASoC: Fix snd_soc_find_dai() matching component by name
ASoC: rsnd: remove unsupported PAUSE flag
ASoC: fsi: remove unsupported PAUSE flag
ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump
Pull ACPI power management fix from Rafael Wysocki:
"This is just a one-liner fixing a regression introduced in 3.13 that
broke system suspend on some Chromebooks.
On those machines there are ACPI device objects for some I2C devices
that can wake up the system from sleep states, but that is done via a
platform-specific mechanism and the ACPI objects don't contain any
wakeup-related information. When we started to use ACPI power
management with those devices (which happened during the 3.13 cycle),
their configuration confused the ACPI PM layer that returned error
codes from suspend callbacks for them causing system suspend to fail.
However, the ACPI PM layer can safely ignore the wakeup setting from a
device driver if the ACPI object corresponding to the device in
question doesn't contain wakeup information in which case the driver
itself is responsible for setting up the device for system wakeup"
* tag 'pm+acpi-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Ignore wakeup setting if the ACPI companion can't wake up
Pull devicetree fixes from Rob Herring:
"DeviceTree fixes for 3.18:
- two fixes for OF selftest code
- fix for PowerPC address parsing to disable work-around except on
old PowerMACs
- fix a crash when earlycon is enabled, but no device is found
- DT documentation fixes and missing vendor prefixes
All but the doc updates are also for stable"
* tag 'devicetree-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/selftest: Fix testing when /aliases is missing
of/selftest: Fix off-by-one error in removal path
documentation: pinctrl bindings: Fix trivial typo 'abitrary'
devicetree: bindings: Add vendor prefix for Micron Technology, Inc.
of: Add vendor prefix for Chips&Media, Inc.
of/base: Fix PowerPC address parsing hack
devicetree: vendor-prefixes.txt: fix whitespace
of: Fix crash if an earlycon driver is not found
of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
of: Spelling s/stucture/structure/
devicetree: bindings: add sandisk to the vendor prefixes
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
PAE kernels, an APM X-Gene problem (it depended on a generic change we
removed before merging), a fix for my hotplug device configuration
changes, and a devicetree documentation update.
Resource management:
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug:
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver:
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene:
- Assign resources to bus before adding new devices (Duc Dang)"
* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
PCI: Apply _HPX Link Control settings to all devices with a link
PCI: Add missing DT binding for "linux,pci-domain" property
PCI: xgene: Assign resources to bus before adding new devices
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target-pending fixes queued for v3.18-rc6.
The highlights include:
- target-core OOPs fix with tcm_qla2xxx + vxworks FC initiators +
zero length SCSI commands having a transfer direction set. (Roland
+ Craig Watson)
- vhost-scsi OOPs fix to explicitly prevent WWPN endpoint configfs
group removal while qemu still has an active reference. (Paolo +
nab)
- ib_srpt fix for RDMA hardware with lower srp_sq_size limits.
(Bart)
- two ib_isert work-arounds for running on ocrdma hardware (Or + Sagi
+ Chris)
- iscsi-target discovery portal typo + SPC-3 PR Preempt SA key
matching fix (Steve)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
IB/isert: Adjust CQ size to HW limits
target: return CONFLICT only when SA key unmatched
iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
ib_isert: Add max_send_sge=2 minimum for control PDU responses
srp-target: Retry when QP creation fails with ENOMEM
iscsi-target: return the correct port in SendTargets
vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
target: Don't call TFO->write_pending if data_length == 0
Pull dmaengine fixes from Vinod Koul:
"We have couple of fixes for dmaengine queued up:
- dma mempcy fix for dma configuration of sun6i by Maxime
- pl330 fixes: First the fixing allocation for data buffers by Liviu
and then Jon's fixe for fifo width and usage"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Fix allocation size for PL330 data buffer depth.
dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
dmaengine: pl330: Align DMA memcpy operations to MFIFO width
dmaengine: sun6i: Fix memcpy operation
Pull MIPS fixes from Ralf Baechle:
"More 3.18 fixes for MIPS:
- backtraces were not quite working on on 64-bit kernels
- loongson needs a different cache coherency setting
- Loongson 3 is a MIPS64 R2 version but due to erratum we treat is an
older architecture revision.
- fix build errors due to undefined references to __node_distances
for certain configurations.
- fix instruction decodig in the jump label code.
- for certain configurations copy_{from,to}_user destroy the content
of $3 so that register needs to be marked as clobbed by the calling
code.
- Hardware Table Walker fixes.
- fill the delay slot of the last instruction of memcpy otherwise
whatever ends up there randomly might have undesirable effects.
- ensure get_user/__get_user always zero the variable to be read even
in case of an error"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: jump_label.c: Handle the microMIPS J instruction encoding
MIPS: jump_label.c: Correct the span of the J instruction
MIPS: Zero variable read by get_user / __get_user in case of an error.
MIPS: lib: memcpy: Restore NOP on delay slot before returning to caller
MIPS: tlb-r4k: Add missing HTW stop/start sequences
MIPS: asm: uaccess: Add v1 register to clobber list on EVA
MIPS: oprofile: Fix backtrace on 64-bit kernel
MIPS: Loongson: Set Loongson-3's ISA level to MIPS64R1
MIPS: Loongson: Fix the write-combine CCA value setting
MIPS: IP27: Fix __node_distances undefined error
MIPS: Loongson3: Fix __node_distances undefined error
Pull powerpc fix from Michael Ellerman:
"One fix from Scott, he says:
This patch fixes a crash (introduced in v3.18-rc1) in the FSL MSI driver
when threaded IRQs are enabled"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/fsl_msi: mark the msi cascade handler IRQF_NO_THREAD
Pull x86 fixes from Thomas Gleixner:
"Misc fixes:
- gold linker build fix
- noxsave command line parsing fix
- bugfix for NX setup
- microcode resume path bug fix
- _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
lockup thread"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
x86, kaslr: Handle Gold linker for finding bss/brk
x86, mm: Set NX across entire PMD at boot
x86, microcode: Update BSPs microcode on resume
x86: Require exact match for 'noxsave' command line option
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: two NUMA fixes, two cputime fixes and an RCU/lockdep fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency
sched/cputime: Fix cpu_timer_sample_group() double accounting
sched/numa: Avoid selecting oneself as swap target
sched/numa: Fix out of bounds read in sched_init_numa()
sched: Remove lockdep check in sched_move_task()
Pull perf fixes from Ingo Molnar:
"Misc fixes: two Intel uncore driver fixes, a CPU-hotplug fix and a
build dependencies fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix boot crash on SBOX PMU on Haswell-EP
perf/x86/intel/uncore: Fix IRP uncore register offsets on Haswell EP
perf: Fix corruption of sibling list with hotplug
perf/x86: Fix embarrasing typo
Pull core fix from Ingo Molnar:
"Fix GENMASK macro shift overflow"
Nobody seems to currently use GENMASK() to fill every single last bit
(which is what overflows) in-tree, and gcc would warn about it, so we
have that going for us. But apparently there are pending changes that
want this.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bitops: Fix shift overflow in GENMASK macros
Commit c3ae62af8e ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.
This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a886b ("tcp: accept RST without ACK flag").
Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.
RFC5961 section 4 states that:
... the handling of the SYN in the synchronized state SHOULD be
performed as follows:
1) If the SYN bit is set, irrespective of the sequence number, TCP
MUST send an ACK (also referred to as challenge ACK) to the remote
peer:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
After sending the acknowledgment, TCP MUST drop the unacceptable
segment and stop processing further.
By sending an ACK, the remote peer is challenged to confirm the loss
of the previous connection and the request to start a new connection.
A legitimate peer, after restart, would not have a TCB in the
synchronized state. Thus, when the ACK arrives, the peer should send
a RST segment back with the sequence number derived from the ACK
field that caused the RST.
This RST will confirm that the remote peer has indeed closed the
previous connection. Upon receipt of a valid RST, the local TCP
endpoint MUST terminate its connection. The local TCP endpoint
should then rely on SYN retransmission from the remote end to
re-establish the connection.
This patch lets SYN packets through the discard added in c3ae62af8e,
so that spurious SYN packets are properly dealt with as per the RFC.
The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions cpufreq_cooling_unregister() and thermal_zone_device_unregister()
test whether their argument is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Prevents build warning:
st_thermal.c:278:12:
warning: ‘st_thermal_suspend’ defined but not used [-Wunused-function]
st_thermal.c:286:12:
warning: ‘st_thermal_resume’ defined but not used [-Wunused-function]
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The toggle bit shouldn't be cleared before the toggle value is calculated.
This should probably go into 3.17.x as well.
Fixes: 120703f9eb ([media] rc-core: document the protocol type)
Cc: stable@vger.kernel.org # For v3.17
Tested-by: Stephan Raue <mailinglists@openelec.tv>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I'm using the new Open Source Group address for my upstream work.
While the other email is still valid, it is better for me to receive
patches via the new address.
So, replace it everywhere inside MAINTAINERS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The IRQs have to be acknowledged before they are serviced, otherwise some events
may be skipped. Also, acknowledging IRQs just before returning from the handler
doesn't leave enough time for the device to deassert the INTx line, and for
bridges to propagate this change. This resulted in twice the IRQ rate on ARMv6
dual core CPU.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Acked-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Tested-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"The biggest change is to rename the filesystem from "overlayfs" to "overlay".
This will allow legacy overlayfs to be easily carried by distros alongside the
new mainline one. Also fix a couple of copy-up races and allow escaping comma
character in filenames."
The last bit is about commas in pathname mount options...
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes XMOS DSD sample format to DSD_U32_BE and also adds
DSD_U16_BE and DSD_U32_BE sample formats.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Acked-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 6e80e3d875 ("ARM: exynos_defconfig: Enable MAX77802")
enabled support for the max77802 regulators but the PMIC also
has a Real-Time-Clock (RTC) and 2-channel 32kHz clock outputs.
Enable the kernel config options to have the drivers for these
devices built-in since they are present in many Exynos boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If the Designware core is configured with IC_EMPTYFIFO_HOLD_MASTER_EN
set to zero, allowing the TX FIFO to become empty causes a STOP
condition to be generated on the I2C bus. If the transmit FIFO
threshold is set too high, an erroneous STOP condition can be
generated on long transfers - particularly where the interrupt
latency is extended.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 1d7afc9594 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Cc: <stable@vger.kernel.org> # v3.7+
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two bugfixes for your net tree, they are:
1) Validate netlink group from nfnetlink to avoid an out of bound array
access. This should only happen with superuser priviledges though.
Discovered by Andrey Ryabinin using trinity.
2) Don't push ethernet header before calling the netfilter output hook
for multicast traffic, this breaks ebtables since it expects to see
skb->data pointing to the network header, patch from Linus Luessing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-20
Please full this little batch of fixes intended for the 3.18 stream!
For the mac80211 patch, Johannes says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
On top of that...
Ben Greear fixes an ath9k regression in which a BSSID mask is
miscalculated.
Dmitry Torokhov corrects an error handling routing in brcmfmac which
was checking an unsigned variable for a negative value.
Johannes Berg avoids a build problem in brcmfmac for arches where
linux/unaligned/access_ok.h and asm/unaligned.h conflict.
Mathy Vanhoef addresses another brcmfmac issue so as to eliminate a
use-after-free of the URB transfer buffer if a timeout occurs.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Peer priority groups were being reversed, but this was missed in the previous
fix sent out for this issue.
v2 : Previous patch was doing extra unnecessary work, result is the same.
Please ignore previous patch
Fixes : ee7bc3cdc2 ('cxgb4 : dcb open-lldp interop fixes')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an old regression introduced by commit
b0d0d915 (ipx: remove the BKL).
When a recvmsg syscall blocks waiting for new data, no data can be sent on the
same socket with sendmsg because ipx_recvmsg() sleeps with the socket locked.
This breaks mars-nwe (NetWare emulator):
- the ncpserv process reads the request using recvmsg
- ncpserv forks and spawns nwconn
- ncpserv calls a (blocking) recvmsg and waits for new requests
- nwconn deadlocks in sendmsg on the same socket
Commit b0d0d915 has simply replaced BKL locking with
lock_sock/release_sock. Unlike now, BKL got unlocked while
sleeping, so a blocking recvmsg did not block a concurrent
sendmsg.
Only keep the socket locked while actually working with the socket data and
release it prior to calling skb_recv_datagram().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace doesn't provide a mask, OVS datapath generates a fully
unwildcarded mask for the flow by copying the flow and setting all bits
in all fields. For IPv6 label, this creates a mask that matches on the
upper 12 bits, causing the following error:
openvswitch: netlink: Invalid IPv6 flow label value (value=ffffffff, max=fffff)
This patch ignores the label validation check for masks, avoiding this
error.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pptp_getname() only partially initializes the stack variable sa,
particularly only fills the pptp part of the sa_addr union. The code
thereby discloses 16 bytes of kernel stack memory via getsockname().
Fix this by memset(0)'ing the union before.
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix one regression and one endian issue.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix endian swapping in vbios fetch for tdp table
drm/radeon: disable native backlight control on pre-r6xx asics (v2)
Existing code updates cupfreq policy only while executing
cpufreq_apply_cooling() function (i.e. when notify_device != NOTIFY_INVALID).
It doesn't apply constraints when cpufreq policy update happens from any other
place but it should update the cpufreq policy with thermal constraints every
time when there is a cpufreq policy update, to keep state of
cpufreq_cooling_device and max_feq of cpufreq policy in sync. For instance
while resuming cpufreq updates cpufreq_policy and it restores default
policy->usr_policy values irrespective of cooling device's cpufreq_state since
notification gets missed because (notify_device == NOTIFY_INVALID).
Another problem, is that userspace is able to change max_freq irrespective of
cooling device's state, as notification gets missed.
This patch modifies code to maintain a global cpufreq_dev_list and applies
constraints of all matching cooling devices for policy's cpu when there is any
policy update(ends up applying the lowest max_freq among the matching cpu
cooling devices).
This patch also removes redundant check (max_freq > policy->user_policy.max),
as cpufreq framework takes care of user_policy constraints already where ever
required, otherwise its causing an issue while increasing max_freq in normal
scenerio as it restores max_freq with policy->user_policy.max which is old
(smaller) value.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
snd_nativeinstruments_control_get() uses a stack as a buffer for
usb_control_msg(), but it's basically not allowed. Replace the call
with a safer helper, snd_usb_ctl_msg(), instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).
Cc: stable@vger.kernel.org # v3.17
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes newly introduced static checker warning in
ufshcd_parse_clock_info, introduced by UFS power management series.
Warning:
drivers/scsi/ufs/ufshcd-pltfrm.c:138 ufshcd_parse_clock_info()
warn: passing devm_ allocated variable to kfree. 'clkfreq'
To fix it we remove the kfree(clkfreq) statement.
In addition we removed the redundant goto label.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes newly introduced static checker warning in
__ufshcd_setup_clocks, introduced by UFS power management series.
Warning:
drivers/scsi/ufs/ufshcd.c:4474 __ufshcd_setup_clocks()
warn: we tested 'ret' before and it was 'false'
To fix it we remove the (!ret) from the condition.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes newly introduced sparse warning in
ufshcd_system_suspend, introduced by UFS power management series.
Sparse warning:
drivers/scsi/ufs/ufshcd.c:5118 ufshcd_system_suspend()
error: we previously assumed 'hba' could be null (see line 5089)
To fix it, we return 0 in case HBA is not initialized or is
not powered.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just use the acpi interface. That's what windows uses on this
generation and it's the only thing that seems to work reliably
on these generation parts.
You can still force the native backlight interface by setting
radeon.backlight=1
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=88501
v2: merge into above if/else block
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After link start-up power mode will always be PWM G1. This is not
reflected in the pwr_info struct which will keep the previous values.
Since ufshcd_change_power_mode() tries to avoid unnecessary power mode
change if the requested power mode and current power mode are same,
power mode change won't execute again after driver initialization.
This patch solves the problem by setting pwr_info to PWM G1 after link
start-up.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS driver adds three well known LUs in the initialization, but those
reference counts are not decremented, so it makes ufshcd module
impossible to unload.
This fixes it by putting scsi_device_put() in the initalization, and in
order to protect concurrent access to hba->sdev_ufs_device (UFS Device
W-LU) from manual delete, increment the reference count while requesting
device power mode setting.
The rest of W-LUs (hba->sdev_boot and hba->sdev_rpmb) are not directly
used from driver, so these references in struct ufs_hba are removed.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Intel Multi-Flex LUNs choke on REPORT SUPPORTED OPERATION CODES
resulting in sd_mod hanging for several minutes on startup.
The issue was introduced with WRITE SAME discovery heuristics.
Fixes: 5db44863b6 ("[SCSI] sd: Implement support for WRITE SAME")
Signed-off-by: Christian Sünkenberg <christian.suenkenberg@hfg-karlsruhe.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Check against !OVL_PATH_LOWER instead of OVL_PATH_MERGE. For a copied up
directory the two are currently equivalent.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pass dentry into ovl_dir_read_merged() insted of upperpath and lowerpath.
This cleans up callers and paves the way for multi-layer directory reads.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Xattr operations can race with copy up. This does not matter as long as
we consistently fiter out "trunsted.overlay.opaque" attribute on upper
directories.
Previously we checked parent against OVL_PATH_MERGE. This is too general,
and prone to race with copy-up. I.e. we found the parent to be on the
lower layer but ovl_dentry_real() would return the copied-up dentry,
possibly with the "opaque" attribute.
So instead use ovl_path_real() and decide to filter the attributes based on
the actual type of the dentry we'll use.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
ovl_remove_and_whiteout() needs to check if upper dentry exists or not
after having locked upper parent directory.
Previously we used a "type" value computed before locking the upper parent
directory, which is susceptible to racing with copy-up.
There's a similar check in ovl_check_empty_and_clear(). This one is not
actually racy, since copy-up doesn't change the "emptyness" property of a
directory. Add a comment to this effect, and check the existence of upper
dentry locally to make the code cleaner.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Some distributions carry an "old" format of overlayfs while mainline has a
"new" format.
The distros will possibly want to keep the old overlayfs alongside the new
for compatibility reasons.
To make it possible to differentiate the two versions change the name of
the new one from "overlayfs" to "overlay".
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Andy Whitcroft <apw@canonical.com>
The /aliases node isn't always present in the device tree, but the
unittest code assumes that /aliases is there. Add a check when inserting
the testcase data to see if of_aliases needs to be updated, and undo the
settings when the nodes are removed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org>
isert has an issue of trying to create a CQ with more CQEs than are
supported by the hardware, that currently results in failures during
isert_device creation during first session login.
This is the isert version of the patch that Minh Tran submitted for
iser, and is simple a workaround required to function with existing
ocrdma hardware.
Signed-off-by: Chris Moore <chris.moore@emulex.com>
Reviewied-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
two regression fixes.
* tag 'drm-intel-fixes-2014-11-19' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Kick fbdev before vgacon
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
As reported by Dmitry, on some Chromebooks there are devices with
corresponding ACPI objects and with unusual system wakeup
configuration. Namely, they technically are wakeup-capable, but the
wakeup is handled via a platform-specific out-of-band mechanism and
the ACPI PM layer has no information on the wakeup capability. As
a result, device_may_wakeup(dev) called from acpi_dev_suspend_late()
returns 'true' for those devices, but the wakeup.flags.valid flag is
unset for the corresponding ACPI device objects, so acpi_device_wakeup()
reproducibly fails for them causing acpi_dev_suspend_late() to return
an error code. The entire system suspend is then aborted and the
machines in question cannot suspend at all.
Address the problem by ignoring the device_may_wakeup(dev) return
value in acpi_dev_suspend_late() if the ACPI companion of the device
being handled has wakeup.flags.valid unset (in which case it is clear
that the wakeup is supposed to be handled by other means).
This fixes a regression introduced by commit a76e9bd89a (i2c:
attach/detach I2C client device to the ACPI power domain) as the
affected systems could suspend and resume successfully before that
commit.
Fixes: a76e9bd89a (i2c: attach/detach I2C client device to the ACPI power domain)
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
g762_remove() needs to first call hwmon_device_unregister() and then
g762_of_clock_disable(). For that reason, it is not possible to
convert it to devm_hwmon_device_register_with_groups() and the
the non device managed version must be used.
This is correctly stated in commit message for 398e16db62 ("hwmon:
(g762) Convert to hwmon_device_register_with_groups") but the
associated changes do in fact introduce a call to the device managed
version of the function.
This patch fixes that typo by switching to the non devm_ version.
Fixes: 398e16db62 ("hwmon: (g762) Convert to hwmon_device_register_with_groups")
Cc: stable@vger.kernel.org (3.17+)
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cxgb4i was returning wrong error and not releasing module reference if remote
end abruptly closed TCP connection. This prevents the cxgb4 network module from
being unloaded, further affecting other network drivers dependent on cxgb4
Sending to net as this affects all cxgb4 based network drivers.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pim6_protocol was added when initiation, but it not deleted.
Similarly, unregister RTNL_FAMILY_IP6MR rtnetlink.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:
pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
...
pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
pci 0000:00:02.2: PCI bridge to [bus 03-04]
pci 0000:00:02.2: bridge window [io 0x1000-0x1fff]
pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff]
pci 0000:00:02.2: can't handle 64-bit address space for bridge
In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address. But
this is a bus address, so we should use dma_addr_t instead.
Use dma_addr_t to hold the bridge window base and limit.
The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.
[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes: d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The currect code for nfsd41_cb_get_slot() and nfsd4_cb_done() has no
locking in order to guarantee atomicity, and so allows for races of
the form.
Task 1 Task 2
====== ======
if (test_and_set_bit(0) != 0) {
clear_bit(0)
rpc_wake_up_next(queue)
rpc_sleep_on(queue)
return false;
}
This patch breaks the race condition by adding a retest of the bit
after the call to rpc_sleep_on().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Johannes Berg <johannes@sipsolutions.net> says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marc Kleine-Budde says:
====================
pull-request: can 2014-11-18
this is a pull request of 17 patches for net/master for the v3.18 release
cycle.
The last patch of this pull request ("can: m_can: update to support CAN FD
features") adds, as the description says, a new feature to the m_can driver. As
the m_can driver has been added in v3.18 there is no risk of causing a
regression. Give me a note if this is not okay and I'll create a new pull
request without it.
There is a patch for the CAN infrastructure by Thomas Körper which fixes
calling kfree_skb() from interrupt context. Roman Fietze fixes a typo also in
the infrastructure. A patch by Dong Aisheng adds a generic helper function to
tell if a skb is normal CAN or CAN-FD frame. Alexey Khoroshilov of the Linux
Driver Verification project fixes a memory leak in the esd_usb2 driver. Two
patches by Sudip Mukherjee remove unused variables and fixe the signess of a
variable. Three patches by me add the missing .ndo_change_mtu callback to the
xilinx_can, rcar_can and gs_usb driver.
The remaining patches improve the m_can driver: David Cohen adds the missing
CONFIG_HAS_IOMEM dependency. Dong Aisheng provides 6 bugfix patches (most
important: missing RAM init, sleep in NAPI poll, dlc in RTR). While the last of
his patches adds CAN FD support to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is currently missing, which results in a crash when one attempts
to set VXLAN tunnel over the mlx4_en when acting as PF.
[ 2408.785472] BUG: unable to handle kernel NULL pointer dereference at (null)
[...]
[ 2408.994104] Call Trace:
[ 2408.996584] [<ffffffffa021f7f5>] ? vxlan_get_rx_port+0xd6/0x103 [vxlan]
[ 2409.003316] [<ffffffffa021f71f>] ? vxlan_lowerdev_event+0xf2/0xf2 [vxlan]
[ 2409.010225] [<ffffffffa0630358>] mlx4_en_start_port+0x862/0x96a [mlx4_en]
[ 2409.017132] [<ffffffffa063070f>] mlx4_en_open+0x17f/0x1b8 [mlx4_en]
While here, make sure to invoke vxlan_get_rx_port() only when VXLAN
offloads are actually enabled and not when they are only supported.
Reported-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fde8f037e ("bonding: fix locking in
bond_loadbalance_arp_mon()") we can have a stale bond carrier state and
stale curr_active_slave when using arp monitoring in loadbalance modes. The
reason is that in bond_loadbalance_arp_mon() we can't have
do_failover == true but slave_state_changed == false, whenever do_failover
is true then slave_state_changed is also true. Then the following piece
from bond_loadbalance_arp_mon():
if (slave_state_changed) {
bond_slave_state_change(bond);
if (BOND_MODE(bond) == BOND_MODE_XOR)
bond_update_slave_arr(bond, NULL);
} else if (do_failover) {
block_netpoll_tx();
bond_select_active_slave(bond);
unblock_netpoll_tx();
}
will execute only the first branch, always and regardless of do_failover.
Since these two events aren't related in such way, we need to decouple and
consider them separately.
For example this issue could lead to the following result:
Bonding Mode: load balancing (round-robin)
*MII Status: down*
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 100
ARP IP target/s (n.n.n.n form): 192.168.9.2
Slave Interface: ens12
*MII Status: up*
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: 00:0f:53:01:42:2c
Slave queue ID: 0
Slave Interface: eth1
*MII Status: up*
Speed: Unknown
Duplex: Unknown
Link Failure Count: 70
Permanent HW addr: 52:54:00:2f:0f:8e
Slave queue ID: 0
Since some interfaces are up, then the status of the bond should also be
up, but it will never change unless something invokes bond_set_carrier()
(i.e. enslave, bond_select_active_slave etc). Now, if I force the
calling of bond_select_active_slave via for example changing
primary_reselect (it can change in any mode), then the MII status goes to
"up" because it calls bond_select_active_slave() which should've been done
from bond_loadbalance_arp_mon() itself.
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
Fixes: 6fde8f037e ("bonding: fix locking in bond_loadbalance_arp_mon()")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fair reader/writer locks mean that btrfs_clear_path_blocking needs
to strictly follow lock ordering rules even when we already have
blocking locks on a given path.
Before we can clear a blocking lock on the path, we need to make sure
all of the locks have been converted to blocking. This will remove lock
inversions against anyone spinning in write_lock() against the buffers
we're trying to get read locks on. These inversions didn't exist before
the fair read/writer locks, but now we need to be more careful.
We papered over this deadlock in the past by changing
btrfs_try_read_lock() to be a true trylock against both the spinlock and
the blocking lock. This was slower, and not sufficient to fix all the
deadlocks. This patch adds a btrfs_tree_read_lock_atomic(), which
basically means get the spinlock but trylock on the blocking lock.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reported-by: Patrick Schmid <schmid@phys.ethz.ch>
cc: stable@vger.kernel.org #v3.15+
With the isofs_hash() function removed, isofs_hash_ms() is the only user
of isofs_hash_common(), but it's defined inside of an #ifdef, which triggers
this gcc warning in ARM axm55xx_defconfig starting with v3.18-rc3:
fs/isofs/inode.c:177:1: warning: 'isofs_hash_common' defined but not used [-Wunused-function]
This patch moves the function inside of the same #ifdef section to avoid that
warning, which seems the best compromise of a relatively harmless patch for
a late -rc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b0afd8e5db ("isofs: don't bother with ->d_op for normal case")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In "d_prune_alias(): just lock the parent and call __dentry_kill()" the old
dget + d_drop + dput has been replaced with lock_parent + __dentry_kill;
unfortunately, dput() does more than just killing dentry - it also drops the
reference to parent. New variant leaks that reference and needs dput(parent)
after killing the child off.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The removal path for selftest data has an off by one error that causes
the code to dereference beyond the end of the nodes[] array on the first
pass through. The old code only worked by chance on a lot of platforms,
but the bug was recently exposed on aarch64.
The fix is simple. Decrement the node count before dereferencing, not
after.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
This patch fixes a long standing issue introduced during the 3.16 merge window.
Shortly after the merge, exynos5250-based arndale boards began to produce the
following errors:
kern.err kernel: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage
kern.err kernel: cpufreq: __target_index: Failed to change cpu frequency: -22
Further analysis revealed that the S5M8767 voltage regulator used on the
exynos5250-based arndale board utilizes the S3C2410 I2C controller. If the
S3C2410 I2C controller driver is not enabled, the S5M8767 voltage regulator
fails to probe. Therefore a dependency exists between these two drivers.
In the exynos_defconfig both CONFIG_REGULATOR_S5M8767 and CONFIG_I2C_S3C2410
options are enabled, and no errors are produced. However, in the
multi_v7_defconfig only the CONFIG_REGULATOR_S5M8767 option is enabled and the
errors are present. So let's enable the CONFIG_I2C_S3C2410 option in the
multi_v7_defconfig to allow the S5M8767 voltage regulator to probe.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Implement the microMIPS encoding of the J instruction for the purpose of
the static keys feature, fixing a crash early on in bootstrap as the
kernel is unhappy seeing the ISA bit set in jump table entries. Make
sure the ISA bit correctly reflects the instruction encoding chosen for
the kernel, 0 for the standard MIPS and 1 for the microMIPS encoding.
Also make sure the instruction to patch is a 32-bit NOP in the microMIPS
mode as by default the 16-bit short encoding is assumed
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8516/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the check for the span of the 256MB segment addressable by the J
instruction according to this instruction's semantics. The calculation
of the jump target is applied to the address of the delay-slot
instruction that immediately follows. Adjust the check accordingly by
adding 4 to `e->code' that holds the address of the J instruction
itself.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8515/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit cf62a8b813 ("MIPS: lib: memcpy: Use macro to build the
copy_user code") switched to a macro in order to build the memcpy
symbols in preparation for the EVA support. However, this commit
also removed the NOP instruction after the 'jr ra' when returning
back to the caller. This had no visible side-effects since the next
instruction was a load to the t0 register which was already in the
clobbered list, but it may have undesired effects in the future
if some other code is introduced in between the .Ldone and
the .Ll_exc_copy labels.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8512/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HTW needs to stop and start again whenever the EntryHI register
changes otherwise an inflight HTW operation might use the new
EntryHI register for updating an old entry and that could lead
to crashes or even a machine check exception. We fix this by
ensuring the HTW has stop whenever the EntryHI register is about
to change
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8511/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When EVA is turned on and prefetching is being used in memcpy.S,
the v1 register is being used as a helper register to the PREFE
instruction. However, v1 ($3) was not in the clobber list, which
means that the compiler did not preserve it across function calls,
and that could corrupt the value of the register leading to all
sorts of userland crashes. We fix this problem by using the
DADDI_SCRATCH macro to define the clobbered register when
CONFIG_EVA && CONFIG_CPU_HAS_PREFETCH are enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8510/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
export the __node_distances symbol in the ip27 memory code to fix the
build error:
Building modules, stage 2.
MODPOST 311 modules
ERROR: "__node_distances" [drivers/block/nvme.ko] undefined!
scripts/Makefile.modpost:90: recipe for target '__modpost' failed
when building the kernel with:
CONFIG_SGI_IP27=y
CONFIG_BLK_DEV_NVME=m
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Even when security labels are disabled we support at least the same
attributes as v4.1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull "ARM: tegra: Device tree fixes for v3.18-rc5" from Thierry Reding:
This contains the serial port numbering fixes that are required for the
serial port numbering to stay the same with or without the serial core
making use of the aliases defined in DT.
eMMC is also fixed for TN7 and Roth boards which were using the wrong
regulators.
* tag 'tegra-for-3.18-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Renesas ARM Based SoC DT Fixes for v3.18" from Simon Horman:
* Correct IIC0 parent clock on r8a7740
* Correct SD3CKCR address to device tree on r8a7790
* tag 'renesas-dt-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Renesas ARM Based SoC Fixes for v3.18" from Simon Horman:
* Set i2c clks_per_count to 2 on kzm9g
* tag 'renesas-soc-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes: 6b8f1ca558 ("USB: ssu100: set tty_flags in ssu100_process_packet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reporting of overrun errors, which are not associated with a
character. Instead insert a null character and report only once.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Merge "Allwinner fixes for 3.18" from Maxime Ripard:
A fix for the A31 dma controller that requires the AHB clock to be parented to
PLL6 in order to operate.
* tag 'sunxi-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The interrupts were activated and the handler registered before the clockevent
was registered in the probe function.
The interrupt handler, however, was making the assumption that the clockevent
device was registered.
That could cause a null pointer dereference if the timer interrupt was firing
during this narrow window.
Fix that by moving the clockevent registration before the interrupt is enabled.
Reported-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Explicitly set the dr_mode for the dwc3 controller on the
Snow board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is
build with USB gadget support.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A misspelled 'arbitrary' propagated to quite a few locations in the DT
binding documentation for pin-controllers. Fixing by:
git grep abitrary | cut -f1 -d: | xargs sed -i 's/abitrary/arbitrary/'
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch is used to add vendor prefix for Micron Technology, Inc. in
the vendor-prefixes.txt file.
Micron Technology, Inc. is an American multinational corporation based
in Boise, Idaho, best known for producing many forms of semiconductor
devices. This includes DRAM, SDRAM, flash memory, eMMC and SSDs.
Signed-off-by: Bean Huo <bpqw@micron.com>
[robh: cleanup commit msg formatting and company name]
Signed-off-by: Rob Herring <robh@kernel.org>
Chips&Media is a developer of Video Codec IP cores.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[robh: fix-up alphabetical ordering]
Signed-off-by: Rob Herring <robh@kernel.org>
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
__earlycon_of_table_sentinel.compatible is a char[128], not a pointer, so
it will never be NULL. Checking it against NULL causes the match loop to
run past the end of the array, and eventually match a bogus entry, under
the following conditions:
- Kernel command line specifies "earlycon" with no parameters
- DT has a stdout-path pointing to a UART node
- The UART driver doesn't use OF_EARLYCON_DECLARE (or maybe the console
driver is compiled out)
Fix this by checking to see if match->compatible is a non-empty string.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rob Herring <robh@kernel.org>
a9ecdc0fdc ("of/irq: Fix lookup to use 'interrupts-extended' property
first") updated the description to say that:
- Both 'interrupts' and 'interrupts-extended' may be present
- Software should prefer 'interrupts-extended'
- Software that doesn't comprehend 'interrupts-extended' may use
'interrupts'
But there is still a paragraph at the end that prohibits having both and
says 'interrupts' should be preferred.
Remove the contradictory text.
Fixes: a9ecdc0fdc ("of/irq: Fix lookup to use 'interrupts-extended' property first")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.13+
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When setting up permissions on kernel memory at boot, the end of the
PMD that was split from bss remained executable. It should be NX like
the rest. This performs a PMD alignment instead of a PAGE alignment to
get the correct span of memory.
Before:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82c00000 10M RW PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82df5000 2004K RW GLB NX pte
0xffffffff82df5000-0xffffffff82e00000 44K RW GLB x pte
0xffffffff82e00000-0xffffffffc0000000 978M pmd
After:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82e00000 12M RW PSE GLB NX pmd
0xffffffff82e00000-0xffffffffc0000000 978M pmd
[ tglx: Changed it to roundup(_brk_end, PMD_SIZE) and added a comment.
We really should unmap the reminder along with the holes
caused by init,initdata etc. but thats a different issue ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141114194737.GA3091@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add sandisk to the list of vendors. This prefix should be used
also for companies absorbed by Sandisk, like M-Systems.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Rob Herring <robh@kernel.org>
The variable err was of the type u32. It was being compared with < 0, and being
an unsigned variable the comparison would have been always false.
Moreover, err was getting the return value from set_reset_mode() and
xcan_set_bittiming(), and both are returning int.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit 8c328a262f ("spi: sirf: Avoid duplicate code in various
bits_per_word cases") is wrong in setting data width register of
fifo is not right, it should use sspi->word_width >> 1 to set
related bits. According to hardware spec, the mapping between
register value and data width:
0 - byte
1 - WORD
2 - DWORD
Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN device drivers can use can_is_canfd_skb() to check if the frame to send
is on CAN FD mode or normal CAN mode.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in CAN's dev.c:
CIA -> CiA
which stands for CAN in Automation.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The microphone mute led on the Latitude E5550 can't work. We need to
apply DELL_WMI_MIC_MUTE_LED quirk to this machine.
The machine uses alc293 codec and already applied the quirk
ALC293_FIXUP_DELL1_MIC_NO_PRESENCE through pin_fixup_tbl[].
Here we just let DELL_WMI_MIC_MUTE_LED be chained to
ALC269_FIXUP_HEADSET_MODE, then the machine will have these
quirks ALC293_FIXUP_DELL1_MIC_NO_PRESENCE-->
ALC269_FIXUP_HEADSET_MODE-->ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED.
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have one more Dell machine needs DELL_WMI_MIC_MUTE_LED quirk, but
the machine uses alc293 instead of alc255. So if
DELL_WMI_MIC_MUTE_LED still chain ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
the machine can't use this quirk.
To change this situation, let the DELL_WMI_MIC_MUTE_LED to be a
standalone quirk, and let other quirks chain it.
After this change, this quirk can be chained to any existing quirks,
and as a result, it is possible that this quirk is applied to
a non-Dell machine or a Dell machine without mic mute led on it, but
it is still safe since alc_fixup_dell_wmi() will return an error in
these situations.
And remove the quirk for machine with subsystem id 0x6010 and 0x601f,
these two machines will fall back to the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE-->ALC255_FIXUP_HEADSET_MODE-->
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED through pin_fixup_tbl[].
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 543c043cba ("powerpc/fsl_msi: change the irq handler from
chained to normal") changes the msi cascade handler from chained to
normal. Since cascade handler must run in hard interrupt context, this
will cause kernel panic if we force threading of all the interrupt
handler via kernel command parameter 'threadirqs'. So mark the irq
handler IRQF_NO_THREAD explicitly.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
ASoC: Fixes for v3.18
As well as the usual driver fixes there's a few other things here:
One is a fix for a race in DPCM which is unfortuantely a rather large
diffstat, this is the result of growing usage of the mainline code and
hence more detailed testing so I'm relatively happy.
The other is a fix for non-DT machine driver matching following some of
the componentization work which is much more focused.
Both have had a while to cook in -next.
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial fix to check the A bit of CCCR for memory frequency
calculations, where the shift of the bit index was missing, triggering a
wrong calculation of memory frequency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 79c6ab5095 (clk: divider: add CLK_DIVIDER_READ_ONLY flag) in
v3.16 introduced the CLK_DIVIDER_READ_ONLY flag which caused the
recalc_rate() and round_rate() clock callbacks to be omitted.
However using this flag has the unfortunate side effect of causing the
clock recalculation code when a clock rate change is attempted to always
treat it as a pass-through clock, i.e. with a fixed divide of 1, which
may not be the case. Child clock rates are then recalculated using the
wrong parent rate.
Therefore instead of dropping the recalc_rate() and round_rate()
callbacks, alter clk_divider_bestdiv() to always report the current
divider as the best divider so that it is never altered.
For me the read only clock was the system clock, which divided the PLL
rate by 2, from which both the UART and the SPI clocks were divided.
Initial setting of the UART rate set it correctly, but when the SPI
clock was set, the other child clocks were miscalculated. The UART clock
was recalculated using the PLL rate as the parent rate, resulting in a
UART new_rate of double what it should be, and a UART which spewed forth
garbage when the rate changes were propagated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Max Schwarz <max.schwarz@online.de>
Cc: <stable@vger.kernel.org> # v3.16+
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
There is a duplication in a clock name for apq8084 platform that causes
the following warning: "RBCPR_CLK_SRC" redefined
Resolve this by adding a MMSS_ prefix to this clock and making its name
coherent with msm8974 platform.
Fixes: 2b46cd23a5 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
at91rm9200_clk_usb_set_rate might fail depending on the requested rate,
because the parent_rate / rate remainder is not necessarily zero.
Moreover, when rounding down the calculated rate we might alter the
divisor calculation and end up with an invalid divisor.
To solve those problems, accept a non zero remainder, and always round
division to the closest result.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Specified in section 5.2.5.6.1 of the USB Audio Class 2.0 definition.
Solves the following error for C-Media 6632A (Asus Xonar U7):
[ 8219.676164] cannot get ctl value: req = 0x81, wValue = 0x0, wIndex = 0x1400, type = 3
Signed-off-by: Johan Rastén <johan@oljud.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ebtables on the OUTPUT chain (NF_BR_LOCAL_OUT) would not work as expected
for both locally generated IGMP and MLD queries. The IP header specific
filter options are off by 14 Bytes for netfilter (actual output on
interfaces is fine).
NF_HOOK() expects the skb->data to point to the IP header, not the
ethernet one (while dev_queue_xmit() does not). Luckily there is an
br_dev_queue_push_xmit() helper function already - let's just use that.
Introduced by eb1d164143
("bridge: Add core IGMP snooping support")
Ebtables example:
$ ebtables -I OUTPUT -p IPv6 -o eth1 --logical-out br0 \
--log --log-level 6 --log-ip6 --log-prefix="~EBT: " -j DROP
before (broken):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=64a4:39c2:86dd:6000:0000:0020:0001:fe80 IPv6 \
DST=0000:0000:0000:0004:64ff:fea4:39c2:ff02, \
IPv6 priority=0x3, Next Header=2
after (working):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=fe80:0000:0000:0000:0004:64ff:fea4:39c2 IPv6 \
DST=ff02:0000:0000:0000:0000:0000:0000:0001, \
IPv6 priority=0x0, Next Header=0
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make sure the netlink group exists, otherwise you can trigger an out
of bound array memory access from the netlink_bind() path. This splat
can only be triggered only by superuser.
[ 180.203600] UBSan: Undefined behaviour in ../net/netfilter/nfnetlink.c:467:28
[ 180.204249] index 9 is out of range for type 'int [9]'
[ 180.204697] CPU: 0 PID: 1771 Comm: trinity-main Not tainted 3.18.0-rc4-mm1+ #122
[ 180.205365] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org
+04/01/2014
[ 180.206498] 0000000000000018 0000000000000000 0000000000000009 ffff88007bdf7da8
[ 180.207220] ffffffff82b0ef5f 0000000000000092 ffffffff845ae2e0 ffff88007bdf7db8
[ 180.207887] ffffffff8199e489 ffff88007bdf7e18 ffffffff8199ea22 0000003900000000
[ 180.208639] Call Trace:
[ 180.208857] dump_stack (lib/dump_stack.c:52)
[ 180.209370] ubsan_epilogue (lib/ubsan.c:174)
[ 180.209849] __ubsan_handle_out_of_bounds (lib/ubsan.c:400)
[ 180.210512] nfnetlink_bind (net/netfilter/nfnetlink.c:467)
[ 180.210986] netlink_bind (net/netlink/af_netlink.c:1483)
[ 180.211495] SYSC_bind (net/socket.c:1541)
Moreover, define the missing nf_tables and nf_acct multicast groups too.
Reported-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The datasheet for PL330 says that the data buffer value in the CRD
register is 10bits wide. However, the value stored is "minus one",
which the driver corrects for. Maximum value that the data buffer
depth can have is 1024 lines, which requires 11 bits for storage.
While making updates I found printing the peripheral ID as a hex
value to be more useful as the datasheet shows the values that way.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MFIFO is shared by all channels so restrict each memcpy to it's fair
share. This is being over cautious, but without a global view of DMA
channel usage on a system it's not possible to come up with a more
optimum safe limit.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The algorithm used for programming the DMA Controller doesn't take into
consideration the requirements of transfers that are not aligned to the
bus width. This failure may result in DMA transferring one too few MFIFO
entries (so too few bytes are copied) or the DMA trying to write one too
many MFIFO entries and hanging because this is never provided.
See "MFIFO Usage Overview" chapter in the the TRM for "CoreLink DMA
Controller DMA-330", Revision r1p1.
We work around these shortcomings by making sure we pick a burst size
and length which ensures no bursts straddle an MFIFO entry.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
[squashed linker error "undefined reference to `__aeabi_uldivmod]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.
touchpad-edge-detector output:
> Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
> Move one finger around the touchpad to detect the actual edges
> Kernel says: x [1472..5674], y [1408..4684]
> Touchpad sends: x [1264..5675], y [1171..4688]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Cc: stable@vger.kernel.org
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20
head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0
dev:port1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:100!
invalid opcode: 0000 [#1] SMP
Modules linked in: ixgbe(O)
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4
[...]
Call Trace:
<IRQ>
[<ffffffff80578226>] ? skb_put+0x3a/0x3b
[<ffffffff80612a5d>] ? add_grhead+0x45/0x8e
[<ffffffff80612e3a>] ? add_grec+0x394/0x3d4
[<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d
[<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45
[<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68
[<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182
[<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d
[<ffffffff8025112b>] ? irq_exit+0x4e/0xd3
[<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46
[<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6ead
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com>
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the threshold to low by default. With this thresholds any movement
on the device with this sensor will generate event.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the mode to push/pull type instead of open drain as some
platforms fails to drive the GPIO pin with open drain.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pravin B Shelar says:
====================
Open vSwitch
Following fixes are accumulated in ovs-repo.
Three of them are related to protocol processing, one is
related to memory leak in case of error and one is to
fix race.
Patch "Validate IPv6 flow key and mask values" has conflicts
with net-next, Let me know if you want me to send the patch
for net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Solves possible lockup issues that can be seen from firmware DCB agents calling
into the DCB app api.
DCB firmware event queues can be tied in with NAPI so that dcb events are
generated in softIRQ context. This can results in calls to dcb_*app()
functions which try to take the dcb_lock.
If the the event triggers while we also have the dcb_lock because lldpad or
some other agent happened to be issuing a get/set command we could see a cpu
lockup.
This code was not originally written with firmware agents in mind, hence
grabbing dcb_lock from softIRQ context was not considered.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of any failure ieee802154fake_probe() just calls unregister_netdev().
But it does not look safe to unregister netdevice before it was registered.
The patch implements straightforward resource deallocation in case of
failure in ieee802154fake_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter updates for your net tree,
they are:
1) Fix missing initialization of the range structure (allocated in the
stack) in nft_masq_{ipv4, ipv6}_eval, from Daniel Borkmann.
2) Make sure the data we receive from userspace contains the req_version
structure, otherwise return an error incomplete on truncated input.
From Dan Carpenter.
3) Fix handling og skb->sk which may cause incorrect handling
of connections from a local process. Via Simon Horman, patch from
Calvin Owens.
4) Fix wrong netns in nft_compat when setting target and match params
structure.
5) Relax chain type validation in nft_compat that was recently included,
this broke the matches that need to be run from the route chain type.
Now iptables-test.py automated regression tests report success again
and we avoid the only possible problematic case, which is the use of
nat targets out of nat chain type.
6) Use match->table to validate the tablename, instead of the match->name.
Again patch for nft_compat.
7) Restore the synchronous release of objects from the commit and abort
path in nf_tables. This is causing two major problems: splats when using
nft_compat, given that matches and targets may sleep and call_rcu is
invoked from softirq context. Moreover Patrick reported possible event
notification reordering when rules refer to anonymous sets.
8) Fix race condition in between packets that are being confirmed by
conntrack and the ctnetlink flush operation. This happens since the
removal of the central spinlock. Thanks to Jesper D. Brouer to looking
into this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to add an unreachable route incorrectly returns -ESRCH if
if custom FIB rules are present:
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: Network is unreachable
[root@localhost ~]# ip rule add to 55.66.77.88 table 200
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: No such process
[root@localhost ~]#
Commit 83886b6b63 ("[NET]: Change "not found"
return value for rule lookup") changed fib_rules_lookup()
to use -ESRCH as a "not found" code internally, but for user space it
should be translated into -ENETUNREACH. Handle the translation centrally in
ipv4-specific fib_lookup(), leaving the DECnet case alone.
On a related note, commit b7a71b51ee
("ipv4: removed redundant conditional") removed a similar translation from
ip_route_input_slow() prematurely AIUI.
Fixes: b7a71b51ee ("ipv4: removed redundant conditional")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some very similarly named command-line options:
arch/x86/kernel/cpu/common.c:__setup("noxsave", x86_xsave_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaveopt", x86_xsaveopt_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaves", x86_xsaves_setup);
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit d670ec1317 "posix-cpu-timers: Cure SMP wobbles" fixes one glibc
test case in cost of breaking another one. After that commit, calling
clock_nanosleep(TIMER_ABSTIME, X) and then clock_gettime(&Y) can result
of Y time being smaller than X time.
Reproducer/tester can be found further below, it can be compiled and ran by:
gcc -o tst-cpuclock2 tst-cpuclock2.c -pthread
while ./tst-cpuclock2 ; do : ; done
This reproducer, when running on a buggy kernel, will complain
about "clock_gettime difference too small".
Issue happens because on start in thread_group_cputimer() we initialize
sum_exec_runtime of cputimer with threads runtime not yet accounted and
then add the threads runtime to running cputimer again on scheduler
tick, making it's sum_exec_runtime bigger than actual threads runtime.
KOSAKI Motohiro posted a fix for this problem, but that patch was never
applied: https://lkml.org/lkml/2013/5/26/191 .
This patch takes different approach to cure the problem. It calls
update_curr() when cputimer starts, that assure we will have updated
stats of running threads and on the next schedule tick we will account
only the runtime that elapsed from cputimer start. That also assure we
have consistent state between cpu times of individual threads and cpu
time of the process consisted by those threads.
Full reproducer (tst-cpuclock2.c):
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <stdio.h>
#include <time.h>
#include <pthread.h>
#include <stdint.h>
#include <inttypes.h>
/* Parameters for the Linux kernel ABI for CPU clocks. */
#define CPUCLOCK_SCHED 2
#define MAKE_PROCESS_CPUCLOCK(pid, clock) \
((~(clockid_t) (pid) << 3) | (clockid_t) (clock))
static pthread_barrier_t barrier;
/* Help advance the clock. */
static void *chew_cpu(void *arg)
{
pthread_barrier_wait(&barrier);
while (1) ;
return NULL;
}
/* Don't use the glibc wrapper. */
static int do_nanosleep(int flags, const struct timespec *req)
{
clockid_t clock_id = MAKE_PROCESS_CPUCLOCK(0, CPUCLOCK_SCHED);
return syscall(SYS_clock_nanosleep, clock_id, flags, req, NULL);
}
static int64_t tsdiff(const struct timespec *before, const struct timespec *after)
{
int64_t before_i = before->tv_sec * 1000000000ULL + before->tv_nsec;
int64_t after_i = after->tv_sec * 1000000000ULL + after->tv_nsec;
return after_i - before_i;
}
int main(void)
{
int result = 0;
pthread_t th;
pthread_barrier_init(&barrier, NULL, 2);
if (pthread_create(&th, NULL, chew_cpu, NULL) != 0) {
perror("pthread_create");
return 1;
}
pthread_barrier_wait(&barrier);
/* The test. */
struct timespec before, after, sleeptimeabs;
int64_t sleepdiff, diffabs;
const struct timespec sleeptime = {.tv_sec = 0,.tv_nsec = 100000000 };
/* The relative nanosleep. Not sure why this is needed, but its presence
seems to make it easier to reproduce the problem. */
if (do_nanosleep(0, &sleeptime) != 0) {
perror("clock_nanosleep");
return 1;
}
/* Get the current time. */
if (clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &before) < 0) {
perror("clock_gettime[2]");
return 1;
}
/* Compute the absolute sleep time based on the current time. */
uint64_t nsec = before.tv_nsec + sleeptime.tv_nsec;
sleeptimeabs.tv_sec = before.tv_sec + nsec / 1000000000;
sleeptimeabs.tv_nsec = nsec % 1000000000;
/* Sleep for the computed time. */
if (do_nanosleep(TIMER_ABSTIME, &sleeptimeabs) != 0) {
perror("absolute clock_nanosleep");
return 1;
}
/* Get the time after the sleep. */
if (clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &after) < 0) {
perror("clock_gettime[3]");
return 1;
}
/* The time after sleep should always be equal to or after the absolute sleep
time passed to clock_nanosleep. */
sleepdiff = tsdiff(&sleeptimeabs, &after);
if (sleepdiff < 0) {
printf("absolute clock_nanosleep woke too early: %" PRId64 "\n", sleepdiff);
result = 1;
printf("Before %llu.%09llu\n", before.tv_sec, before.tv_nsec);
printf("After %llu.%09llu\n", after.tv_sec, after.tv_nsec);
printf("Sleep %llu.%09llu\n", sleeptimeabs.tv_sec, sleeptimeabs.tv_nsec);
}
/* The difference between the timestamps taken before and after the
clock_nanosleep call should be equal to or more than the duration of the
sleep. */
diffabs = tsdiff(&before, &after);
if (diffabs < sleeptime.tv_nsec) {
printf("clock_gettime difference too small: %" PRId64 "\n", diffabs);
result = 1;
}
pthread_cancel(th);
return result;
}
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20141112155843.GA24803@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There were several reports that on some systems writing the SBOX0 PMU
initialization MSR would #GP at boot. This did not happen on all
systems -- my two test systems booted fine.
Writing the three initialization bits bit-by-bit seems to avoid the
problem. So add a special callback to do just that.
This replaces an earlier patch that disabled the SBOX.
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-and-Tested-by: Patrick Lu <patrick.lu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1415062828-19759-4-git-send-email-andi@firstfloor.org
[ Fixed a whitespace error and added attribution tags that were left out inexplicably. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a USB control message delay quirk for a few specific Marantz/Denon
devices. Without the delay the DACs will not work properly and produces the
following type of messages:
Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use
Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use
There are likely other Marantz/Denon devices using the same USB module which exhibit the
same problems. But as this cannot be verified I limited the patch to the devices
I could test.
The following two devices are covered by this path:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a CPU hotplugged out, we call perf_remove_from_context() (via
perf_event_exit_cpu()) to rip each CPU-bound event out of its PMU's cpu
context, but leave siblings grouped together. Freeing of these events is
left to the mercy of the usual refcounting.
When a CPU-bound event's refcount drops to zero we cross-call to
__perf_remove_from_context() to clean it up, detaching grouped siblings.
This works when the relevant CPU is online, but will fail if the CPU is
currently offline, and we won't detach the event from its siblings
before freeing the event, leaving the sibling list corrupt. If the
sibling list is later walked (e.g. because the CPU cam online again
before a remaining sibling's refcount drops to zero), we will walk the
now corrupted siblings list, potentially dereferencing garbage values.
Given that the events should never be scheduled again (as we removed
them from their context), we can simply detatch siblings when the CPU
goes down in the first place. If the CPU comes back online, the
redundant call to __perf_remove_from_context() is safe.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: vincent.weaver@maine.edu
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1415203904-25308-2-git-send-email-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, we get the new GSEL bits by OR-ing the old values
with the new ones. This only works first time when the old
values are 0.
Startup:
* GSEL0 = 0, GSEL1 = 0
Set range to 4G: (GSEL0 = 1, GSEL1 = 0)
* GSEL0 = 0 | 1 = 1
* GSEL1 = 0 | 0 = 0
* correct
Change range to 2G: (GSEL0 = 0, GSEL1 = 0)
* GSEL0 = 1 | 0 = 1
* GSEL1 = 0 | 0 = 0
* wrong, GSEL0 should be 0
This has the nice effect that we can use the full scale range,
exported in in_accel_scale_available.
Fixes: a735e3d7f0 (iio: accel: kxcjk-1013: Set adjustable range)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The direction field is set on 7 bits, thus we need to AND it with 0111 111 mask
in order to retrieve it, that is 0x7F, not 0xCF as it is now.
Fixes: ade7ef7ba (staging:iio: Differential channel handling)
Signed-off-by: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
dp read operations depends on ovs_dp_cmd_fill_info(). This API
needs to looup vport to find dp name, but vport lookup can
fail. Therefore to keep vport reference alive we need to
take ovs lock.
Introduced by commit 6093ae9aba ("openvswitch: Minimize
dp and vport critical sections").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
match_validate() enforce that a mask matching on NDP attributes has also an
exact match on ICMPv6 type.
The ICMPv6 type, which is 8-bit wide, is stored in the 'tp.src' field of
'struct sw_flow_key', which is 16-bit wide.
Therefore, an exact match on ICMPv6 type should only check the first 8 bits.
This commit fixes a bug that prevented flows with an exact match on NDP field
from being installed
Introduced by commit 03f0d916aa ("openvswitch: Mega flow implementation").
Signed-off-by: Daniele Di Proietto <ddiproietto@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The checksum of ICMPv6 packets uses the IP pseudoheader as part of
the calculation, unlike ICMP in IPv4. This was not implemented,
which means that modifying the IP addresses of an ICMPv6 packet
would cause the checksum to no longer be correct as the psuedoheader
did not match.
Introduced by commit 3fdbd1ce11 ("openvswitch: add ipv6 'set' action").
Reported-by: Neal Shrader <icosahedral@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Need to free memory in case of sample action error.
Introduced by commit 651887b0c2 ("openvswitch: Sample
action without side effects").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Joe Stringer says:
====================
Implement ndo_gso_check() for vxlan nics
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not other
UDP-based encapsulation protocols where the format and size of the header may
differ. This patch series implements a generic ndo_gso_check() for detecting
VXLAN, then reuses it for these NICs.
Implementation shamelessly stolen from Tom Herbert (with minor fixups):
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
v2: Drop i40e/fm10k patches (code diverged; handling separately).
Refactor common code into vxlan_gso_check() helper.
Minor style fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-13
Please pull this set of a few more wireless fixes intended for the
3.18 stream...
For the mac80211 bits, Johannes says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
For the iwlwifi bits, Emmanuel says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
On top of that...
Arend van Spriel corrects a channel width conversion that caused a
WARNING in brcmfmac.
Hauke Mehrtens avoids a NULL pointer dereference in b43.
Larry Finger hits a trio of rtlwifi bugs left over from recent
backporting from the Realtek vendor driver.
Miaoqing Pan fixes a clocking problem in ath9k that could affect
packet timestamps and such.
Stanislaw Gruszka addresses an payload alignment issue that has been
plaguing rt2x00.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be a signed overflow in the following code.
The expression, (32-logmask) is comprised between 0 and 31 included.
It may be equal to 31.
In such a case the left shift will produce a signed integer overflow.
According to the C99 Standard, this is an undefined behavior.
A simple fix is to replace the signed int 1 with the unsigned int 1U.
Signed-off-by: Vincent BENAYOUN <vincent.benayoun@trust-in-soft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removal of the central spinlock nf_conntrack_lock, in
commit 93bb0ceb75 ("netfilter: conntrack: remove central
spinlock nf_conntrack_lock"), it is possible to race against
get_next_corpse().
The race is against the get_next_corpse() cleanup on
the "unconfirmed" list (a per-cpu list with seperate locking),
which set the DYING bit.
Fix this race, in __nf_conntrack_confirm(), by removing the CT
from unconfirmed list before checking the DYING bit. In case
race occured, re-add the CT to the dying list.
While at this, fix coding style of the comment that has been
updated.
Fixes: 93bb0ceb75 ("netfilter: conntrack: remove central spinlock nf_conntrack_lock")
Reported-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and
of_get_pci_domain_nr()") added parsing of the "linux,pci-domain" property,
but didn't add the binding documentation.
Since this property will be supported by a number of host bridge drivers,
add it to the common PCI binding doc.
Fixes: 41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Felipe writes:
usb: fixes for v3.18-rc5
Just one fix here on dwc3 which fixes a minor
bug caused by a fix that went in this v3.18-rc
cycle.
The corner case is minimal as it can only be
reproduced with back-to-back Setup transfers
(without starting data or status phase) by
means of a LeCroy USB Trainer, where we can
generate USB packets any way we like.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The X-Gene PCIe driver assumes pci_scan_root_bus() assigns resources as
proposed in [1]. But we dropped patch [1] because it would break some
architectures, which means the X-Gene PCIe driver is currently broken.
Add calls to scan the bus, assign resources, and add devices in the X-Gene
driver to fix this.
[bhelgaas: changelog]
[1] http://lkml.kernel.org/r/1412000971-9242-11-git-send-email-Liviu.Dudau@arm.com
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vddio_sdmmc3 is a vdd_io, and thus should be under the vqmmc-supply
property, not vmmc-supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This property was wrong and broke eMMC since commit 52221610d ("mmc:
sdhci: Improve external VDD regulator support"). Align the eMMC
properties to those of other Tegra boards.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These labels will be used to provide deterministic numbering of consoles
in a later patch.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
[treding@nvidia.com: drop aliases, reword commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
In commit a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver"),
the I2C part of the CS42L51 was moved to a separate file, but the
definition of the of_device_id array was left in the driver file
itself, no longer connected to the platform_driver structure using the
.of_match_table pointer.
This commit exports the of_device_id array in cs42l51, and uses it as
.of_match_able in cs42l51-i2c.c. This solution was suggested by Brian
Austin.
Fixes: a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The existing xtables matches and targets, when used from nft_compat, may
sleep from the destroy path, ie. when removing rules. Since the objects
are released via call_rcu from softirq context, this results in lockdep
splats and possible lockups that may be hard to reproduce.
Patrick also indicated that delayed object release via call_rcu can
cause us problems in the ordering of event notifications when anonymous
sets are in place.
So, this patch restores the synchronous object release from the commit
and abort paths. This includes a call to synchronize_rcu() to make sure
that no packets are walking on the objects that are going to be
released. This is slowier though, but it's simple and it resolves the
aforementioned problems.
This is a partial revert of c7c32e7 ("netfilter: nf_tables: defer all
object release via rcu") that was introduced in 3.16 to speed up
interaction with userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of the match->name, which is of course not relevant.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check for nat chain dependency only, which is the one that can
actually crash the kernel. Don't care if mangle, filter and security
specific match and targets are used out of their scope, they are
harmless.
This restores iptables-compat with mangle specific match/target when
used out of the OUTPUT chain, that are actually emulated through filter
chains, which broke when performing strict validation.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The prep_memcpy call was not setting any meaningful burst and width because it
was relying on the dma_slave_config was not set already.
Rework the needed conversion functions, and hardcode the width and burst to
use.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ip_vs_prepare_tunneled_skb() ignores ->sk when allocating a new
skb, either unconditionally setting ->sk to NULL or allowing
the uninitialized ->sk from a newly allocated skb to leak through
to the caller.
This patch properly copies ->sk and increments its reference count.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
On sh73a0/kzm9g-legacy, probing of the i2c masters fails with:
i2c-sh_mobile i2c-sh_mobile.0: timing values out of range: L/H=0x208/0x1bf
sh_mobile: probe of i2c-sh_mobile.0 failed with error -22
According to the datasheet, the transfer rate is derived from the HP
clock (which runs at 104 MHz) divided by two. Hence
i2c_sh_mobile_platform_data.clks_per_count should be set to two.
Now probing succeeds, and i2c works:
i2c-sh_mobile i2c-sh_mobile.0: I2C adapter 0 with bus speed 100000 Hz (L/H=0x104/0xe0)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
chandef_to_chanspec.isra.11+0x158/0x184()
Modules linked in:
CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f #8
[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---
Cc: stable@vger.kernel.org # v3.17
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911https://bugzilla.kernel.org/show_bug.cgi?id=72471http://marc.info/?l=linux-wireless&m=139108549530402&w=2https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We could be reading 8 bytes into a 4 byte buffer here. It seems
harmless but adding a check is the right thing to do and it silences a
static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
phy_read and phy_write are not set for every phy any more sine this:
commit d342b95dd7
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Thu Jul 31 21:59:43 2014 +0200
b43: don't duplicate common PHY read/write ops
b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.
This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731
Reported-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When transferring from the original range in nf_nat_masquerade_{ipv4,ipv6}()
we copy over values from stack in from min_proto/max_proto due to uninitialized
range variable in both, nft_masq_{ipv4,ipv6}_eval. As we only initialize
flags at this time from nft_masq struct, just zero out the rest.
Fixes: 9ba1f726be ("netfilter: nf_tables: add new nft_masq expression")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On latest mm + KASan patchset I've got this:
==================================================================
BUG: AddressSanitizer: out of bounds access in sched_init_smp+0x3ba/0x62c at addr ffff88006d4bee6c
=============================================================================
BUG kmalloc-8 (Not tainted): kasan error
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in alloc_vfsmnt+0xb0/0x2c0 age=75 cpu=0 pid=0
__slab_alloc+0x4b4/0x4f0
__kmalloc_track_caller+0x15f/0x1e0
kstrdup+0x44/0x90
alloc_vfsmnt+0xb0/0x2c0
vfs_kern_mount+0x35/0x190
kern_mount_data+0x25/0x50
pid_ns_prepare_proc+0x19/0x50
alloc_pid+0x5e2/0x630
copy_process.part.41+0xdf5/0x2aa0
do_fork+0xf5/0x460
kernel_thread+0x21/0x30
rest_init+0x1e/0x90
start_kernel+0x522/0x531
x86_64_start_reservations+0x2a/0x2c
x86_64_start_kernel+0x15b/0x16a
INFO: Slab 0xffffea0001b52f80 objects=24 used=22 fp=0xffff88006d4befc0 flags=0x100000000004080
INFO: Object 0xffff88006d4bed20 @offset=3360 fp=0xffff88006d4bee70
Bytes b4 ffff88006d4bed10: 00 00 00 00 00 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a ........ZZZZZZZZ
Object ffff88006d4bed20: 70 72 6f 63 00 6b 6b a5 proc.kk.
Redzone ffff88006d4bed28: cc cc cc cc cc cc cc cc ........
Padding ffff88006d4bee68: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G B 3.18.0-rc3-mm1+ #108
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
ffff88006d4be000 0000000000000000 ffff88006d4bed20 ffff88006c86fd18
ffffffff81cd0a59 0000000000000058 ffff88006d404240 ffff88006c86fd48
ffffffff811fa3a8 ffff88006d404240 ffffea0001b52f80 ffff88006d4bed20
Call Trace:
dump_stack (lib/dump_stack.c:52)
print_trailer (mm/slub.c:645)
object_err (mm/slub.c:652)
? sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
kasan_report_error (mm/kasan/report.c:102 mm/kasan/report.c:178)
? kasan_poison_shadow (mm/kasan/kasan.c:48)
? kasan_unpoison_shadow (mm/kasan/kasan.c:54)
? kasan_poison_shadow (mm/kasan/kasan.c:48)
? kasan_kmalloc (mm/kasan/kasan.c:311)
__asan_load4 (mm/kasan/kasan.c:371)
? sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
kernel_init_freeable (init/main.c:869 init/main.c:997)
? finish_task_switch (kernel/sched/sched.h:1036 kernel/sched/core.c:2248)
? rest_init (init/main.c:924)
kernel_init (init/main.c:929)
? rest_init (init/main.c:924)
ret_from_fork (arch/x86/kernel/entry_64.S:348)
? rest_init (init/main.c:924)
Read of size 4 by task swapper/0:
Memory state around the buggy address:
ffff88006d4beb80: fc fc fc fc fc fc fc fc fc fc 00 fc fc fc fc fc
ffff88006d4bec00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bec80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bed00: fc fc fc fc 00 fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bed80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006d4bee00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc 04 fc
^
ffff88006d4bee80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bef00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bef80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff88006d4bf000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88006d4bf080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Zero 'level' (e.g. on non-NUMA system) causing out of bounds
access in this line:
sched_max_numa_distance = sched_domains_numa_distance[level - 1];
Fix this by exiting from sched_init_numa() earlier.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Fixes: 9942f79ba ("sched/numa: Export info needed for NUMA balancing on complex topologies")
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1415372020-1871-1-git-send-email-a.ryabinin@samsung.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in
14e0e28 dmaengine: sun6i: Remove obsolete clk muxing code
Unfortunately the rest of that series did not make it, leaving us with
broken dma on sun6i.
This patch reparents ahb1_mux to pll6 using the DT assigned-clocks
properties in the dma controller node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
https://bugzilla.kernel.org/show_bug.cgi?id=86831
Markus reported that when shutting down mysqld (with AIO support,
on a ext3 formatted Harddrive) leads to a negative number of dirty pages
(underrun to the counter). The negative number results in a drastic reduction
of the write performance because the page cache is not used, because the kernel
thinks it is still 2 ^ 32 dirty pages open.
Add a warn trace in __dec_zone_state will catch this easily:
static inline void __dec_zone_state(struct zone *zone, enum
zone_stat_item item)
{
atomic_long_dec(&zone->vm_stat[item]);
+ WARN_ON_ONCE(item == NR_FILE_DIRTY &&
atomic_long_read(&zone->vm_stat[item]) < 0);
atomic_long_dec(&vm_stat[item]);
}
[ 21.341632] ------------[ cut here ]------------
[ 21.346294] WARNING: CPU: 0 PID: 309 at include/linux/vmstat.h:242
cancel_dirty_page+0x164/0x224()
[ 21.355296] Modules linked in: wutbox_cp sata_mv
[ 21.359968] CPU: 0 PID: 309 Comm: kworker/0:1 Not tainted 3.14.21-WuT #80
[ 21.366793] Workqueue: events free_ioctx
[ 21.370760] [<c0016a64>] (unwind_backtrace) from [<c0012f88>]
(show_stack+0x20/0x24)
[ 21.378562] [<c0012f88>] (show_stack) from [<c03f8ccc>]
(dump_stack+0x24/0x28)
[ 21.385840] [<c03f8ccc>] (dump_stack) from [<c0023ae4>]
(warn_slowpath_common+0x84/0x9c)
[ 21.393976] [<c0023ae4>] (warn_slowpath_common) from [<c0023bb8>]
(warn_slowpath_null+0x2c/0x34)
[ 21.402800] [<c0023bb8>] (warn_slowpath_null) from [<c00c0688>]
(cancel_dirty_page+0x164/0x224)
[ 21.411524] [<c00c0688>] (cancel_dirty_page) from [<c00c080c>]
(truncate_inode_page+0x8c/0x158)
[ 21.420272] [<c00c080c>] (truncate_inode_page) from [<c00c0a94>]
(truncate_inode_pages_range+0x11c/0x53c)
[ 21.429890] [<c00c0a94>] (truncate_inode_pages_range) from
[<c00c0f6c>] (truncate_pagecache+0x88/0xac)
[ 21.439252] [<c00c0f6c>] (truncate_pagecache) from [<c00c0fec>]
(truncate_setsize+0x5c/0x74)
[ 21.447731] [<c00c0fec>] (truncate_setsize) from [<c013b3a8>]
(put_aio_ring_file.isra.14+0x34/0x90)
[ 21.456826] [<c013b3a8>] (put_aio_ring_file.isra.14) from
[<c013b424>] (aio_free_ring+0x20/0xcc)
[ 21.465660] [<c013b424>] (aio_free_ring) from [<c013b4f4>]
(free_ioctx+0x24/0x44)
[ 21.473190] [<c013b4f4>] (free_ioctx) from [<c003d8d8>]
(process_one_work+0x134/0x47c)
[ 21.481132] [<c003d8d8>] (process_one_work) from [<c003e988>]
(worker_thread+0x130/0x414)
[ 21.489350] [<c003e988>] (worker_thread) from [<c00448ac>]
(kthread+0xd4/0xec)
[ 21.496621] [<c00448ac>] (kthread) from [<c000ec18>]
(ret_from_fork+0x14/0x20)
[ 21.503884] ---[ end trace 79c4bf42c038c9a1 ]---
The cause is that we set the aio ring file pages as *DIRTY* via SetPageDirty
(bypasses the VFS dirty pages increment) when init, and aio fs uses
*default_backing_dev_info* as the backing dev, which does not disable
the dirty pages accounting capability.
So truncating aio ring file will contribute to accounting dirty pages (VFS
dirty pages decrement), then error occurs.
The original goal is keeping these pages in memory (can not be reclaimed
or swapped) in life-time via marking it dirty. But thinking more, we have
already pinned pages via elevating the page's refcount, which can already
achieve the goal, so the SetPageDirty seems unnecessary.
In order to fix the issue, using the __set_page_dirty_no_writeback instead
of the nop .set_page_dirty, and dropped the SetPageDirty (don't manually
set the dirty flags, don't disable set_page_dirty(), rely on default behaviour).
With the above change, the dirty pages accounting can work well. But as we
known, aio fs is an anonymous one, which should never cause any real write-back,
we can ignore the dirty pages (write back) accounting by disabling the dirty
pages (write back) accounting capability. So we introduce an aio private
backing dev info (disabled the ACCT_DIRTY/WRITEBACK/ACCT_WB capabilities) to
replace the default one.
Reported-by: Markus Königshaus <m.koenigshaus@wut.de>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Commit 7ec7c4a9a6 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:
(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)
Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.
This patch adds an additional length check.
Cc: stable@vger.kernel.org
Fixes: 7ec7c4a9a6 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PLL should be powered up once filter power is on. So, "PLL1"
should be connected to filters instead of DACs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Baytrail-based chromebooks have a 20MHz mclk, the code was setting
the divisor incorrectly in this case. According to the 98090
datasheet, the divisor should be set to DIV1 for 10 <= mclk <= 20.
Correct this and the surrounding clock ranges as well to match the
datasheet.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM can update the FE/BE connection states totally asynchronously
from the FE's PCM state. Most of FE/BE state changes are protected by
mutex, so that they won't race, but there are still some actions that
are uncovered. For example, suppose to switch a BE while a FE's
stream is running. This would call soc_dpcm_runtime_update(), which
sets FE's runtime_update flag, then sets up and starts BEs, and clears
FE's runtime_update flag again.
When a device emits XRUN during this operation, the PCM core triggers
snd_pcm_stop(XRUN). Since the trigger action is an atomic ops, this
isn't blocked by the mutex, thus it kicks off DPCM's trigger action.
It eventually updates and clears FE's runtime_update flag while
soc_dpcm_runtime_update() is running concurrently, and it results in
confusion.
Usually, for avoiding such a race, we take a lock. There is a PCM
stream lock for that purpose. However, as already mentioned, the
trigger action is atomic, and we can't take the lock for the whole
soc_dpcm_runtime_update() or other operations that include the lengthy
jobs like hw_params or prepare.
This patch provides an alternative solution. This adds a way to defer
the conflicting trigger callback to be executed at the end of FE/BE
state changes. For doing it, two things are introduced:
- Each runtime_update state change of FEs is protected via PCM stream
lock.
- The FE's trigger callback checks the runtime_update flag. If it's
not set, the trigger action is executed there. If set, mark the
pending trigger action and returns immediately.
- At the exit of runtime_update state change, it checks whether the
pending trigger is present. If yes, it executes the trigger action
at this point.
Reported-and-tested-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
sched_move_task() is the only interface to change sched_task_group:
cpu_cgrp_subsys methods and autogroup_move_group() use it.
Everything is synchronized by task_rq_lock(), so cpu_cgroup_attach()
is ordered with other users of sched_move_task(). This means we do no
need RCU here: if we've dereferenced a tg here, the .attach method
hasn't been called for it yet.
Thus, we should pass "true" to task_css_check() to silence lockdep
warnings.
Fixes: eeb61e53ea ("sched: Fix race between task_group and sched_task_group")
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414473874.8574.2.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
PREEMPT (and PREEMPT AND ABORT) should return CONFLICT iff a specified
SERVICE ACTION RESERVATION KEY is specified and matches no existing
persistent reservation.
Without this patch, a PREEMPT will return CONFLICT if either all
reservations are held by the initiator (self preemption) or there is
nothing to preempt. According to the spec, both of these cases should
succeed.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In this case the cm_id->context is the isert_np, and the cm_id->qp
is NULL, so use that to distinct the cases.
Since we don't expect any other events on this cm_id we can
just return -1 for explicit termination of the cm_id by the
cma layer.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a max_send_sge=2 minimum in isert_conn_setup_qp()
to ensure outgoing control PDU responses with tx_desc->num_sge=2
are able to function correctly.
This addresses a bug with RDMA hardware using dev_attr.max_sge=3,
that in the original code with the ConnectX-2 work-around would
result in isert_conn->max_sge=1 being negotiated.
Originally reported by Chris with ocrdma driver.
Reported-by: Chris Moore <Chris.Moore@emulex.com>
Tested-by: Chris Moore <Chris.Moore@emulex.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
consolidated the lookup of CPU DAIs and CODEC DAIs into a single function.
When matching a component by name for CODEC DAIs the code previous to the
patch compared the name in the DAI link table with component->name. For CPU
DAIs the code compared to dev_name(component->dev). The newly introduced
function ended up using the later as well.
For most components dev_name(component->dev) and component->name are the
same. The main notable exception are I2C devices where the driver name and
the device name are concatenated to form the component name. By using
dev_name(component->dev) instead of component->name the patch broke the
matching of I2C CODECs by name.
This patch restores the original behavior by using component->name instead
of dev_name(component->dev). This will be safe even for CPU DAIs since for
CPU DAIs both are the same.
Fixes: 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not guaranteed to that srp_sq_size is supported
by the HCA. So if we failed to create the QP with ENOMEM,
try with a smaller srp_sq_size. Keep it up until we hit
MIN_SRPT_SQ_SIZE, then fail the connection.
Reported-by: Mark Lehrer <lehrer@gmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The fact that a target is published on the any address has no bearing on
which port(s) it is published. SendTargets should always send the
portal's port, not the port used for discovery.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where individual vhost-scsi configfs endpoint
groups can be removed from below while active exports to QEMU userspace
still exist, resulting in an OOPs.
It adds a configfs_depend_item() in vhost_scsi_set_endpoint() to obtain
an explicit dependency on se_tpg->tpg_group in order to prevent individual
vhost-scsi WWPN endpoints from being released via normal configfs methods
while an QEMU ioctl reference still exists.
Also, add matching configfs_undepend_item() in vhost_scsi_clear_endpoint()
to release the dependency, once QEMU's reference to the individual group
at /sys/kernel/config/target/vhost/$WWPN/$TPGT is released.
(Fix up vhost_scsi_clear_endpoint() error path - DanC)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an initiator sends a zero-length command (e.g. TEST UNIT READY) but
sets the transfer direction in the transport layer to indicate a
data-out phase, we still shouldn't try to transfer data. At best it's
a NOP, and depending on the transport, we might crash on an
uninitialized sg list.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org> # 3.1
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The convention for i2c_device_id name does not need to have company prefix.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel dump (WARN_ON) ocurred during system boot-up inside regmap_write():
------------[ cut here ]------------
WARNING: CPU: 0 PID: 47 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xe8/0x108()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 47 Comm: kworker/u2:2 Not tainted 3.18.0-rc1-10245-gb75d289-dirty #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<80012294>] (dump_backtrace) from [<80012578>] (show_stack+0x18/0x1c)
r6:8097c73c r5:8097c73c r4:00000000 r3:be33ba80
[<80012560>] (show_stack) from [<806aac48>] (dump_stack+0x8c/0xa4)
[<806aabbc>] (dump_stack) from [<8002a694>] (warn_slowpath_common+0x70/0x94)
r6:80062838 r5:00000009 r4:bd827b30 r3:be33ba80
[<8002a624>] (warn_slowpath_common) from [<8002a6f0>] (warn_slowpath_fmt+0x38/0x40)
r8:00000004 r7:00000001 r6:000080d0 r5:60000193 r4:bd826010
[<8002a6bc>] (warn_slowpath_fmt) from [<80062838>] (lockdep_trace_alloc+0xe8/0x108)
r3:80831590 r2:8082e160
[<80062750>] (lockdep_trace_alloc) from [<800ea5dc>] (kmem_cache_alloc+0x28/0x134)
r5:000080d0 r4:be001f00
[<800ea5b4>] (kmem_cache_alloc) from [<8038d72c>] (regcache_rbtree_write+0x15c/0x648)
r10:00000000 r9:0000001c r8:00000004 r7:00000001 r6:00000000 r5:bd819a00
r4:00000000 r3:811aea88
[<8038d5d0>] (regcache_rbtree_write) from [<8038c4d8>] (regcache_write+0x5c/0x64)
r10:be3f9f88 r9:00000000 r8:00000004 r7:00000001 r6:00000000 r5:00000001
r4:bd819a00
[<8038c47c>] (regcache_write) from [<8038b0dc>] (_regmap_raw_write+0x134/0x5f4)
r6:be3f9f84 r5:00000001 r4:bd819a00 r3:00000001
[<8038afa8>] (_regmap_raw_write) from [<8038b610>] (_regmap_bus_raw_write+0x74/0x94)
r10:00000000 r9:00000001 r8:be3fb080 r7:bd819a00 r6:00000001 r5:00000000
r4:bd819a00
[<8038b59c>] (_regmap_bus_raw_write) from [<8038a8b4>] (_regmap_write+0x60/0x9c)
r6:00000001 r5:00000000 r4:bd819a00 r3:8038b59c
[<8038a854>] (_regmap_write) from [<8038ba24>] (regmap_write+0x48/0x68)
r7:bd81ad80 r6:00000001 r5:00000000 r4:bd819a00
[<8038b9dc>] (regmap_write) from [<80528f30>] (fsl_asrc_dai_probe+0x34/0x104)
r6:bd888628 r5:be3fb080 r4:be3b4410 r3:be3b442c
------------[ dump end ]------------
=============================================================================
2741 /*
2742 * Oi! Can't be having __GFP_FS allocations with IRQs disabled.
2743 */
2744 if (DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags)))
2745 return;
=============================================================================
By looking at 2744 line, we can get that it's because regcache_rbtree_write()
would call kmalloc() with GFP flag if it couldn't find an existing block to
insert nodes while this kmalloc() call is inside a spin_lock_irq_save pair,
i.e. IRQs disabled.
Even though this may be a bug that should be fixed, I still try to send this
patch as a quick fix (work around) since it does no harm to assign default
values of every registers when using regcache.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-10-28 00:17:02 +00:00
390 changed files with 2790 additions and 1658 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
