Pull libata fixes from Tejun Heo:
"Three libata fixes for v3.18. Nothing too interesting. PCI ID ID and
quirk additions to ahci and an error handling path fix in sata_fsl"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable MSI on SAMSUNG 0xa800 SSD
sata_fsl: fix error handling of irq_of_parse_and_map
AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller
Pull watchdog fix from Wim Van Sebroeck:
"Fix the watchdog mask bit offset for Exynos7"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
Pull i2c fixes from Wolfram Sang:
"Here are two more driver bugfixes for I2C which would be good to have"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Set the hardware time-out register to maximum value
i2c: davinci: generate STP always when NACK is received
Pull x86 fixes from Thomas Gleixner:
"Two final fixlets for 3.18:
- Prevent microcode reload wreckage on 32bit
- Unbreak cross compilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode: Limit the microcode reloading to 64-bit for now
x86: Use $(OBJDUMP) instead of plain objdump
Pull sound fixlet from Takashi Iwai:
"Just one commit for adding a copule of HD-audio quirk entries"
* tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add headset Mic support for new Dell machine
Pull drm intel fixes from Dave Airlie:
"Two intel stable fixes, that should be it from me for this round"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Pull ACPI backlight fix from Rafael Wysocki:
"This is a simple fix for an ACPI backlight regression introduced by a
recent commit that overlooked a corner case which should have been
taken into account"
* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: update condition to check if device is in _DOD list
Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.
* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Unlock panel even when LVDS is disabled
drm/i915: More cautious with pch fifo underruns
Pull media fixes from Mauro Carvalho Chehab:
"A core fix and some driver fixes:
- regression fix in Remote Controller core affecting RC6 protocol
handling
- fix video buffer handling in cx23885
- race fix in solo6x10
- fix image selection in smiapp
- fix reported payload size on s2255drv
- two updates for MAINTAINERS file"
* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: fix toggle handling in the rc6 decoder
MAINTAINERS: Update mchehab's addresses
[media] cx23885: use sg = sg_next(sg) instead of sg++
[media] s2255drv: fix payload size for JPG, MJPEG
[media] Update MAINTAINERS for solo6x10
[media] solo6x10: fix a race in IRQ handler
[media] smiapp: Only some selection targets are settable
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26 ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context. This causes RCU
warnings and possible failures.
This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c bugfixes from Wolfram Sang:
"A few driver bugfixes for 3.18"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: omap: fix i207 errata handling
i2c: designware: prevent early stop on TX FIFO empty
i2c: omap: fix NACK and Arbitration Lost irq handling
Pull PCI fix from Bjorn Helgaas:
"This fixes a Tegra20 regression that we introduced during the v3.18
merge window"
* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use physical range for I/O mapping
Pull devicetree bugfix from Grant Likely:
"One more bug fix for v3.18. I debated whether or not to send you this
merge request because we're at such a late rc. The bug isn't critical
in that there is only one system known to be affected and the patch is
easy to backport. The codepath is used by pretty much every DT based
system, so there is risk a of regression (it /should/ be safe, but
I've been bitten by stuff that should be safe before). I've had it in
linux-next for a week and haven't received any complaints.
I think it probably should just be merged right away rather than
waiting for the merge window and backporting. It does fix a real bug
and the code is theoretically safer after the change. I can't think
of any situation where it would be dangerous to reserve the DT memory
an extra time.
Summary from tag:
Single bugfix for boot failure seen in the wild. The memory reserve
code tries to be clever about reserving the FDT, but it should just
go ahead and reserve it unconditionally to avoid the problem of
partial overlap described in the patch"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap
Pull block core regression fix from Jens Axboe:
"Single fix for a regression introduced in this development cycle,
where dm on top of dif/dix is broken. From Darrick Wong"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix regression where bio_integrity_process uses wrong bio_vec iterator
Pull drm fixes from Dave Airlie:
"Radeon and Nouveau fixes:
So nouveau had a few regression introduced, Ben and Maarten finally
tracked down the one that was causing problems on my MacBookPro, also
nvidia gave some info on the an engine we were using incorrectly, so
disable our use of it, and one regresion with pci hotplug affecting
optimus users.
Radeon has an oops fixs, sync fix, and one workaround to avoid broken
functionality on 32-bit x86, this needs better root causing and a
better fix, but the bandaid is a lot safer at this point"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
nouveau: move the hotplug ignore to correct place.
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
Pull networking fixes from David Miller:
1) Fill in ethtool link parameters for all link types in cxgb4, from
Hariprasad Shenai.
2) Fix probe regressions in stmmac driver, from Huacai Chen.
3) Network namespace leaks on errirs in rtnetlink, from Nicolas
Dichtel.
4) Remove erroneous BUG check which can actually trigger legitimately,
in xen-netfront. From Seth Forshee.
5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
Thomas Grag.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
cxgb4: Fill in supported link mode for SFP modules
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
sh_eth: Fix sleeping function called from invalid context
stmmac: platform: Move plat_dat checking earlier
sh_eth: Fix skb alloc size and alignment adjust rule.
rtnetlink: release net refcnt on error in do_setlink()
bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes
Pull keyring/nfs fixes from James Morris:
"From David Howells:
The first one fixes the handling of maximum buffer size for key
descriptions, fixing the size at 4095 + NUL char rather than whatever
PAGE_SIZE happens to be and permits you to read back the full
description without it getting clipped because some extra information
got prepended.
The second and third fix a bug in NFS idmapper handling whereby a key
representing a mapping between an id and a name expires and causing
EKEYEXPIRED to be seen internally in NFS (which prevents the mapping
from happening) rather than re-looking up the mapping"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: request_key() should reget expired keys rather than give EKEYEXPIRED
KEYS: Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags
KEYS: Fix the size of the key description passed to/from userspace
Merge misc fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab: fix nodeid bounds check for non-contiguous node IDs
lib/genalloc.c: export devm_gen_pool_create() for modules
mm: fix anon_vma_clone() error treatment
mm: fix swapoff hang after page migration and fork
fat: fix oops on corrupted vfat fs
ipc/sem.c: fully initialize sem_array before making it visible
drivers/input/evdev.c: don't kfree() a vmalloc address
mm/vmpressure.c: fix race in vmpressure_work_fn()
mm: frontswap: invalidate expired data on a dup-store failure
mm: do not overwrite reserved pages counter at show_mem()
The bounds check for nodeid in ____cache_alloc_node gives false
positives on machines where the node IDs are not contiguous, leading to
a panic at boot time. For example, on a POWER8 machine the node IDs are
typically 0, 1, 16 and 17. This means that num_online_nodes() returns
4, so when ____cache_alloc_node is called with nodeid = 16 the VM_BUG_ON
triggers, like this:
kernel BUG at /home/paulus/kernel/kvm/mm/slab.c:3079!
Call Trace:
.____cache_alloc_node+0x5c/0x270 (unreliable)
.kmem_cache_alloc_node_trace+0xdc/0x360
.init_list+0x3c/0x128
.kmem_cache_init+0x1dc/0x258
.start_kernel+0x2a0/0x568
start_here_common+0x20/0xa8
To fix this, we instead compare the nodeid with MAX_NUMNODES, and
additionally make sure it isn't negative (since nodeid is an int). The
check is there mainly to protect the array dereference in the get_node()
call in the next line, and the array being dereferenced is of size
MAX_NUMNODES. If the nodeid is in range but invalid (for example if the
node is off-line), the BUG_ON in the next line will catch that.
Fixes: 14e50c6a9b ("mm: slab: Verify the nodeid passed to ____cache_alloc_node")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).
I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost. In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten. So a failure of anon_vma_clone() will return
success since err at this point is now zero.
Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.
Fixes: ef0855d334 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: <stable@vger.kernel.org> [2.6.18+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) don't bother with ->d_time for positives - we only check it for
negatives anyway.
b) make sure to set it at unlink and rmdir time - at *that* point
soon-to-be negative dentry matches then-current directory contents
c) don't go into renaming of old alias in vfat_lookup() unless it
has the same parent (which it will, unless we are seeing corrupted
image)
[hirofumi@mail.parknet.co.jp: make change minimum, don't call d_move() for dir]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org> [3.17.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipc_addid() makes a new ipc identifier visible to everyone. New objects
start as locked, so that the caller can complete the initialization
after the call. Within struct sem_array, at least sma->sem_base and
sma->sem_nsems are accessed without any locks, therefore this approach
doesn't work.
Thus: Move the ipc_addid() to the end of the initialization.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Reported-by: Rik van Riel <riel@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051
[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
1. use zswap as the frontswap backend with writeback feature
2. store a swap page(version_1) to entry A, success
3. dup-store a newer page(version_2) to the same entry A, fail
4. use __swap_writepage() write version_2 page to swapfile, success
5. zswap do shrink, writeback version_1 page to swapfile
6. version_2 page is overwrited by version_1, data corrupt.
This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few more small fixes for 3.18.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
drm/radeon: sync all BOs involved in a CS v2
Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.
v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
bio integrity handling is broken on a system with LVM layered atop a
DIF/DIX SCSI drive because device mapper clones the bio, modifies the
clone, and sends the clone to the lower layers for processing.
However, the clone bio has bi_vcnt == 0, which means that when the sd
driver calls bio_integrity_process to attach DIX data, the
for_each_segment_all() call (which uses bi_vcnt) returns immediately
and random garbage is sent to the disk on a disk write. The disk of
course returns an error.
Therefore, teach bio_integrity_process() to use bio_for_each_segment()
to iterate the bio_vecs, since the per-bio iterator tracks which
bio_vecs are associated with that particular bio. The integrity
handling code is effectively part of the "driver" (it's not the bio
owner), so it must use the correct iterator function.
v2: Fix a compiler warning about abandoned local variables. This
patch supersedes "block: bio_integrity_process uses wrong bio_vec
iterator". Patch applies against 3.18-rc6.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just a couple of fixes for the fallout from the fence rework.
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/gf116: remove copy1 engine
drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it
Closes a very unlikely race that can occur if another NonStallInterrupt
method passes between checking fences and acking the previous interrupt.
With this change, the interrupt will re-fire under such conditions.
Tested-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull ext4 bugfix from Ted Ts'o:
"Fix an ext4 metadata checksum regression introduced in v3.18-rc3"
* tag 'ext4_for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix regression where we fail to initialize checksum seed when loading
When we're enabling journal features, we cannot use the predicate
jbd2_journal_has_csum_v2or3() because we haven't yet set the sb
feature flag fields! Moreover, we just finished loading the shash
driver, so the test is unnecessary; calculate the seed always.
Without this patch, we fail to initialize the checksum seed the first
time we turn on journal_checksum, which means that all journal blocks
written during that first mount are corrupt. Transactions written
after the second mount will be fine, since the feature flag will be
set in the journal superblock. xfstests generic/{034,321,322} are the
regression tests.
(This is important for 3.18.)
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.coM>
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Commit 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT. Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.
On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge. This helps to make /proc/iomem
more readable.
Combining both of the above, the union would now include the I/O space
region. This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000. Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.
This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space. This allows the translation setup within
the driver to reuse the physical addresses. The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Since the keyring facility can be viewed as a cache (at least in some
applications), the local expiration time on the key should probably be viewed
as a 'needs updating after this time' property rather than an absolute 'anyone
now wanting to use this object is out of luck' property.
Since request_key() is the main interface for the usage of keys, this should
update or replace an expired key rather than issuing EKEYEXPIRED if the local
expiration has been reached (ie. it should refresh the cache).
For absolute conditions where refreshing the cache probably doesn't help, the
key can be negatively instantiated using KEYCTL_REJECT_KEY with EKEYEXPIRED
given as the error to issue. This will still cause request_key() to return
EKEYEXPIRED as that was explicitly set.
In the future, if the key type has an update op available, we might want to
upcall with the expired key and allow the upcall to update it. We would pass
a different operation name (the first column in /etc/request-key.conf) to the
request-key program.
request_key() returning EKEYEXPIRED is causing an NFS problem which Chuck
Lever describes thusly:
After about 10 minutes, my NFSv4 functional tests fail because the
ownership of the test files goes to "-2". Looking at /proc/keys
shows that the id_resolv keys that map to my test user ID have
expired. The ownership problem persists until the expired keys are
purged from the keyring, and fresh keys are obtained.
I bisected the problem to 3.13 commit b2a4df200d ("KEYS: Expand
the capacity of a keyring"). This commit inadvertantly changes the
API contract of the internal function keyring_search_aux().
The root cause appears to be that b2a4df200d made "no state check"
the default behavior. "No state check" means the keyring search
iterator function skips checking the key's expiry timeout, and
returns expired keys. request_key_and_link() depends on getting
an -EAGAIN result code to know when to perform an upcall to refresh
an expired key.
This patch can be tested directly by:
keyctl request2 user debug:fred a @s
keyctl timeout %user:debug:fred 3
sleep 4
keyctl request2 user debug:fred a @s
Without the patch, the last command gives error EKEYEXPIRED, but with the
command it gives a new key.
Reported-by: Carl Hetherington <cth@carlh.net>
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags to be two variations of the
same flag. They are effectively mutually exclusive and one or the other
should be provided, but not both.
Keyring cycle detection and key possession determination are the only things
that set NO_STATE_CHECK, except that neither flag really does anything there
because neither purpose makes use of the keyring_search_iterator() function,
but rather provides their own.
For cycle detection we definitely want to check inside of expired keyrings,
just so that we don't create a cycle we can't get rid of. Revoked keyrings
are cleared at revocation time and can't then be reused, so shouldn't be a
problem either way.
For possession determination, we *might* want to validate each keyring before
searching it: do you possess a key that's hidden behind an expired or just
plain inaccessible keyring? Currently, the answer is yes. Note that you
cannot, however, possess a key behind a revoked keyring because they are
cleared on revocation.
keyring_search() sets DO_STATE_CHECK, which is correct.
request_key_and_link() currently doesn't specify whether to check the key
state or not - but it should set DO_STATE_CHECK.
key_get_instantiation_authkey() also currently doesn't specify whether to
check the key state or not - but it probably should also set DO_STATE_CHECK.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When a key description argument is imported into the kernel from userspace, as
happens in add_key(), request_key(), KEYCTL_JOIN_SESSION_KEYRING,
KEYCTL_SEARCH, the description is copied into a buffer up to PAGE_SIZE in size.
PAGE_SIZE, however, is a variable quantity, depending on the arch. Fix this at
4096 instead (ie. 4095 plus a NUL termination) and define a constant
(KEY_MAX_DESC_SIZE) to this end.
When reading the description back with KEYCTL_DESCRIBE, a PAGE_SIZE internal
buffer is allocated into which the information and description will be
rendered. This means that the description will get truncated if an extremely
long description it has to be crammed into the buffer with the stringified
information. There is no particular need to copy the description into the
buffer, so just copy it directly to userspace in a separate operation.
Reported-by: Christian Kastner <debian@kvr.at>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Christian Kastner <debian@kvr.at>
Commit eb7e7d76 "s390: Replace __get_cpu_var uses" broke machine check
handling.
We copy machine check information from per-cpu to a stack variable for
local processing. Next we should zap the per-cpu variable, not the
stack variable.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
First, there was this: https://bugzilla.kernel.org/show_bug.cgi?id=88001
The problem there was that microcode patches are not being reapplied
after suspend-to-ram. It was important to reapply them, though, because
of for example Haswell's TSX erratum which disabled TSX instructions
with a microcode patch.
A simple fix was fb86b97300 ("x86, microcode: Update BSPs microcode
on resume") but, as it is often the case, simple fixes are too
simple. This one causes 32-bit resume to fail:
https://bugzilla.kernel.org/show_bug.cgi?id=88391
Properly fixing this would require more involved changes for which it
is too late now, right before the merge window. Thus, limit this to
64-bit only temporarily.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1417353999-32236-1-git-send-email-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 0b8db271f1 ("ACPI / video: check _DOD list when creating
backlight devices") checks if the video device is in the bind devices
list to decide if we should create backlight device for it, that causes
problem for one Dell Latitude E6410, where none of the video output
devices are properly bound due to the way how we did the comparing
between its _ADR and the _DOD's values. Solve this problem by comparing
the lower 12 bits of both the device's _ADR and the _DOD's values instead
of relying on bind result.
Fixes: 0b8db271f1 ("ACPI / video: check _DOD list when creating backlight devices")
Reported-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull drm fixes from Dave Airlie:
"Two i915 regressions and one dual-gpu laptop radeon fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: report disconnected for LVDS/eDP with PX if ddc fails
drm/i915: Cancel vdd off work before suspend
drm/i915: Ignore SURFLIVE and flip counter when the GPU gets reset
Don Bailey noticed that our page zeroing for compression at end-io time
isn't complete. This reworks a patch from Linus to push the zeroing
into the zlib and lzo specific functions instead of trying to handle the
corners inside btrfs_decompress_buf2page
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reported-by: Don A. Bailey <donb@securitymouse.com>
cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original code only check/alloc plat_dat for the CONFIG_OF case, this
patch check/alloc it earlier and unconditionally to avoid kernel build
warnings:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:275
stmmac_pltfr_probe() warn: variable dereferenced before check 'plat_dat'
V2: Fix coding style.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d7 ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
"Three fixlets from the ARM SoC camp:
- correct irqdomain initialization for atmel-aic
- correct error handling for device tree parsing in bcm controllers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: brcmstb-l2: Fix error handling of irq_of_parse_and_map
irqchip: bcm7120-l2: Fix error handling of irq_of_parse_and_map
irqchip: atmel-aic: Fix irqdomain initialization
Pull SCSI fixes from James Bottomley:
"This is a set of ten fixes: 8 for UFS including four static checker
warnings, a potential null deref in the voltage regulator code, a race
on module unload, a ref counting fix on the well known LUNs which made
it impossible to remove the ufs module and fix to correct the
information in pwr_info.
In addition to UFS, there's a blacklist for the Intel Multi-Flex array
which chokes on report supported operation codes and a fix to an oops
in bnx2fc caused by shared skbs"
[ For us non-SCSI people: "UFS" here is "Universal Flash Storage" not
the filesystem. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ufs: fix NULL dereference when no regulators are defined
ufs: ensure clk gating work is finished before module unloading
scsi: ufs: fix static checker warning in ufshcd_parse_clock_info
scsi: ufs: fix static checker warning in __ufshcd_setup_clocks
scsi: ufs: fix static checker warning in ufshcd_populate_vreg
scsi: ufs: fix static checker errors in ufshcd_system_suspend
ufs: fix power info after link start-up
ufs: fix reference counting of W-LUs
scsi: add Intel Multi-Flex to scsi scan blacklist
bnx2fc: do not add shared skbs to the fcoe_rx_list
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
Pull tty/serial fix from Greg KH:
"Here is a single revert for the of-serial driver that resolves a
reported issue.
This revert has been in linux-next for a while"
* tag 'tty-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: of-serial: add PM suspend/resume support"
Pull USB fixes from Greg KH:
"Here are some USB driver fixes and new device ids for 3.18-rc7.
Full details are in the shortlog, and all of these have been in the
linux-next tree for a while"
* tag 'usb-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000
usb: xhci: rework root port wake bits if controller isn't allowed to wakeup
USB: xhci: Reset a halted endpoint immediately when we encounter a stall.
Revert "xhci: clear root port wake on bits if controller isn't wake-up capable"
USB: xhci: don't start a halted endpoint before its new dequeue is set
USB: uas: Add no-uas quirk for Hitachi usb-3 enclosures 4971:1012
USB: ssu100: fix overrun-error reporting
USB: keyspan: fix overrun-error reporting
USB: keyspan: fix tty line-status reporting
usb: serial: ftdi_sio: add PIDs for Matrix Orbital products
usb: dwc3: ep0: fix for dead code
USB: serial: cp210x: add IDs for CEL MeshConnect USB Stick
Pull thermal fixes from Eduardo Valentin:
"In this -rc still very minor changes:
- Lee Jones fixes compilation warning in sti thermal driver
- Marjus Elfring removes unnecessary checks in exynos thermal driver
(as per coccinelle)
- Now we always update cpufreq policies, and thus get (hopefully)
always in sync with cpufreq, thanks to Yadwinder"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: Exynos: Deletion of unnecessary checks before two function calls
thermal: sti: Ignore suspend/resume functions when !PM_SLEEP
thermal: cpu_cooling: Update always cpufreq policy with thermal constraints
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
Pull ARM SoC fixes from Arnd Bergmann:
"Not much interesting going on fixes-wise for us this week, as it
should be for an -rc7. I'm not expecting Olof to work much over
Thanksgiving weekend, so I decided to take over again and push these
out to you.
Just four simple fixes this week:
- one missing of_node_put() on armv7 based mvebu
- forcing the USB host into the right mode on Chromebook
(exynos5-snow)
- enabling two important drivers for exynos_defconfig
- fixing a noncritical bug for tegra that would cause a regression
with common code patches queued for 3.19"
* tag 'armsoc-for-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: irq: fix buggy usage of irq_data irq field
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
ARM: dts: Explicitly set dr_mode on exynos5250-snow
ARM: mvebu: add missing of_node_put() call in coherency.c
Pull ARM fixes from Russell King:
"Another round of relatively small ARM fixes.
Thomas spotted that the strex backoff delay bit was a disable bit, so
it needed to be clear for this to work. Vladimir spotted that using a
restart block for the cache flush operation would return -EINTR, which
userspace was not expecting. Dmitry spotted that the auxiliary
control register accesses for Xscale were not correct"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8226/1: cacheflush: get rid of restarting block
ARM: 8222/1: mvebu: enable strex backoff delay
ARM: 8216/1: xscale: correct auxiliary register in suspend/resume
Two regression fixes from Ville.
* tag 'drm-intel-fixes-2014-11-27' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Cancel vdd off work before suspend
drm/i915: Ignore SURFLIVE and flip counter when the GPU gets reset
Pull mips fixes from Ralf Baechle:
"The hopefully final round of fixes for 3.18:
- Fix a number of build errors affecting particular configurations.
- Handle EVA correctly when flushing a signal trampoline and dcache
lines.
- Fix printks printing jibberish.
- Handle 64 bit memory addresses correctly when adding memory chunk
on 32 bit kernels.
- Fix a race condition in the hardware tablewalker code"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: tlbex: Fix potential HTW race on TLBL/M/S handlers
MIPS: Fix address type used for early memory detection.
MIPS: Kconfig: Don't allow both microMIPS and SmartMIPS to be selected.
MIPS: kernel: cps-vec: Set ISA level to mips32r2 for the MIPS MT ASE
MIPS: Netlogic: handle modular AHCI builds
MIPS: Netlogic: handle modular USB case
MIPS: Loongson: Make platform serial setup always built-in.
MIPS: fix EVA & non-SMP non-FPU FP context signal handling
MIPS: cpu-probe: Set the FTLB probability bit on supported cores
MIPS: BMIPS: Fix ".previous without corresponding .section" warnings
MIPS: uaccess.h: Fix strnlen_user comment.
MIPS: r4kcache: Add EVA case for protected_writeback_dcache_line
MIPS: Fix info about plat_setup in arch_mem_init comment
MIPS: rtlx: Remove KERN_DEBUG from pr_debug() arguments in rtlx.c
MIPS: SEAD3: Fix LED device registration.
MIPS: Fix a copy & paste error in unistd.h
Pull powerpc fixes from Michael Ellerman:
"Here are five fixes for you to pull please.
They're all CC'ed to stable except the "Fix PE state format" one which
went in this release"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: 32 bit getcpu VDSO function uses 64 bit instructions
powerpc/powernv: Replace OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE
powerpc/eeh: Fix PE state format
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
powerpc/powernv: Fix the hmi event version check.
Pull sparc fixlet from David Miller:
"Aparc fix to add dma_cache_sync(), even if a nop it should be provided
if dma_{alloc,free}_noncoherent() is provided too"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Add NOP dma_cache_sync() implementation.
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
Pull spi fixes from Mark Brown:
"There's a couple of driver fixes here, plus one core fix for the DMA
mapping which wasn't doing the right thing for vmalloc()ed addresses
that hadn't been through kmap(). It's fairly rare to use vmalloc()
with SPI and it's a subset of those users who might fail so it's
unsurprising that this wasn't noticed sooner"
* tag 'spi-v3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sirf: fix word width configuration
spi: Fix mapping from vmalloc-ed buffer to scatter list
spi: dw: Fix dynamic speed change.
Pull input layer fixes from Dmitry Torokhov:
"The main change is to fix breakage in Elantech driver introduced by
the recent commit adding trackpoint reporting to protocol v4. Now we
are trusting the hardware to advertise the trackpoint properly and do
not try to decode the data as trackpoint if firmware told us it is not
present"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - use proper endpoint type
Input: elantech - trust firmware about trackpoint presence
Input: synaptics - adjust min/max on Thinkpad E540
There is a potential race when probing the TLB in TLBL/M/S exception
handlers for a matching entry. Between the time we hit a TLBL/S/M
exception and the time we get to execute the TLBP instruction, the
HTW may have replaced the TLB entry we are interested in hence the TLB
probe may fail. However, in the existing handlers, we never checked the
status of the TLBP (ie check the result in the C0/Index register). We
fix this by adding such a check when the core implements the HTW. If
we couldn't find a matching entry, we return back and try again.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f ("arm: mm: Add support for PJ4B cpu and init routines")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull "Samsung defconfig update for v3.18" from Kukjin Kim:
- enable max77802 rtc and clock drivers for exynos_defconfig
: enable the kernel config options to have the drivers for
max77802 including rtc and 2-ch 32kHz clock outputs
* tag 'samsung-defconfig-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The crazy gic_arch_extn thing that Tegra uses contains multiple
references to the irq field in struct irq_data, and uses this
to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 25801 2075 GIC 29 twd
17: 0 0 GIC 73 timer0
112: 0 0 GPIO 58 c8000600.sdhci cd
123: 0 0 GPIO 69 c8000200.sdhci cd
279: 1126 0 GIC 122 serial
281: 0 0 GIC 70 7000c000.i2c
282: 0 0 GIC 116 7000c400.i2c
283: 0 0 GIC 124 7000c500.i2c
284: 300 0 GIC 85 7000d000.i2c
[...]
Just replacing all instances of irq with hwirq fixes the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
one fix for PX laptops.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: report disconnected for LVDS/eDP with PX if ddc fails
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd34 ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flag passed to ioda_eeh_phb_reset() should be EEH_RESET_DEACTIVATE,
which is translated to OPAL_DEASSERT_RESET or something else by the
EEH backend accordingly.
The patch replaces OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE for
ioda_eeh_phb_reset().
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce. The patch fixes it up.
Fixes: 2013add4ce ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [c0000003f39ffb10]
pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp: c0000003f39ffc70
msr: 8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40]
pc: 000000000eca7cc4
lr: 000000000eca7c44
sp: fafb4b0
msr: 8000000000001000
dar: 10000000
dsisr: 42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current HMI event structure is an ABI and carries a version field to
accommodate future changes without affecting/rearranging current structure
members that are valid for previous versions.
The current version check "if (hmi_evt->version != OpalHMIEvt_V1)"
doesn't accomodate the fact that the version number may change in
future.
If firmware starts returning an HMI event with version > 1, this check
will fail and no HMI information will be printed on older kernels.
This patch fixes this issue.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Reword changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit fadbe0cd52 entitled "staging:
rtl8188eu:Remove rtw_zmalloc(), wrapper for kzalloc()", the author failed
to note that the original code in the wrapper tested whether the caller
could sleep, and set the flags argument to kzalloc() appropriately.
After the patch, GFP_KERNEL is used unconditionally. Unfortunately, several
of the routines may be entered from an interrupt routine and generate
a BUG splat for every such call. Routine rtw_sitesurvey_cmd() is used in the
example below:
BUG: sleeping function called from invalid context at mm/slub.c:1240
in_atomic(): 1, irqs_disabled(): 0, pid: 756, name: wpa_supplicant
INFO: lockdep is turned off.
CPU: 2 PID: 756 Comm: wpa_supplicant Tainted: G WC O 3.18.0-rc4+ #34
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
ffffc90005557000 ffff880216fafaa8 ffffffff816b0bbf 0000000000000000
ffff8800c3b58000 ffff880216fafac8 ffffffff8107af77 0000000000000001
0000000000000010 ffff880216fafb18 ffffffff811b06ce 0000000000000000
Call Trace:
[<ffffffff816b0bbf>] dump_stack+0x4e/0x71
[<ffffffff8107af77>] __might_sleep+0xf7/0x120
[<ffffffff811b06ce>] kmem_cache_alloc_trace+0x4e/0x1f0
[<ffffffffa0888226>] ? rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa0888226>] rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa088f00d>] rtw_do_join+0x22d/0x370 [r8188eu]
[<ffffffffa088f6e8>] rtw_set_802_11_ssid+0x218/0x3d0 [r8188eu]
[<ffffffffa08c3ca5>] rtw_wx_set_essid+0x1e5/0x410 [r8188eu]
[<ffffffffa08c3ac0>] ? rtw_wx_get_rate+0x50/0x50 [r8188eu]
[<ffffffff816938f1>] ioctl_standard_iw_point+0x151/0x3f0
[<ffffffff81693d52>] ioctl_standard_call+0xb2/0xe0
[<ffffffff81597df7>] ? rtnl_lock+0x17/0x20
[<ffffffff816945a0>] ? iw_handler_get_private+0x70/0x70
[<ffffffff81693ca0>] ? call_commit_handler+0x40/0x40
[<ffffffff81693256>] wireless_process_ioctl+0x176/0x1c0
[<ffffffff81693e79>] wext_handle_ioctl+0x69/0xc0
[<ffffffff8159fe79>] dev_ioctl+0x309/0x5e0
[<ffffffff810be9c7>] ? call_rcu+0x17/0x20
[<ffffffff8156a472>] sock_ioctl+0x142/0x2e0
[<ffffffff811e0c70>] do_vfs_ioctl+0x300/0x520
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff810102bc>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff811e0f11>] SyS_ioctl+0x81/0xa0
[<ffffffff816ba1d2>] system_call_fastpath+0x12/0x17
Additional routines that generate this BUG are rtw_joinbss_cmd(),
rtw_dynamic_chk_wk_cmd(), rtw_lps_ctrl_wk_cmd(), rtw_rpt_timer_cfg_cmd(),
rtw_ps_cmd(), report_survey_event(), report_join_res(), survey_timer_hdl(),
and rtw_check_bcn_info().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: navin patidar <navin.patidar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John W. Linville says:
====================
pull request: wireless 2014-11-26
Please pull this little batch of fixes intended for the 3.18 stream...
For the iwlwifi one, Emmanuel says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Along with that, Larry sends a pair of rtlwifi fixes to address some
discrepancies from moving drivers out of staging. Larry says:
"These two patches are needed to fix a regression introduced when
driver rtl8821ae was moved from staging to the regular wireless tree."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf says:
====================
bridge: Fix missing Netlink message validations
Adds various missing length checks in the bridging code for Netlink
messages and corresponding attributes provided by user space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kvm fixes from Paolo Bonzini:
"Last minute KVM/ARM fixes; even the generic change actually affects
nothing but ARM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: fix kvm_is_mmio_pfn() and rename to kvm_is_reserved_pfn()
arm/arm64: kvm: drop inappropriate use of kvm_is_mmio_pfn()
arm/arm64: KVM: vgic: Fix error code in kvm_vgic_create()
arm64: KVM: Handle traps of ICC_SRE_EL1 as RAZ/WI
arm64: KVM: fix unmapping with 48-bit VAs
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
The commit 3b57de958e brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: bcm_sf2: misc bugfixes
This patch series contains two bug fixes:
- first patch fixes an issue on the error path of the driver where we could
have left some of our registers mapped
- second patch enforces the use of a software reset of the switch to guarantee
the HW is in a consistent state prior to software initialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using kvm_is_mmio_pfn() to decide whether a host region
should be stage 2 mapped with device attributes, add a new static
function kvm_is_device_pfn() that disregards RAM pages with the
reserved bit set, as those should usually not be mapped as device
memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we detect another vCPU is running we just exit and return 0 as if we
succesfully created the VGIC, but the VGIC wouldn't actual be created.
This shouldn't break in-kernel behavior because the kernel will not
observe the failed the attempt to create the VGIC, but userspace could
be rightfully confused.
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When running on a system with a GICv3, we currenly don't allow the guest
to access the system register interface of the GICv3. We do this by
clearing the ICC_SRE_EL2.Enable, which causes all guest accesses to
ICC_SRE_EL1 to trap to EL2 and causes all guest accesses to other ICC_
registers to cause an undefined exception in the guest.
However, we currently don't handle the trap of guest accesses to
ICC_SRE_EL1 and will spill out a warning. The trap just needs to handle
the access as RAZ/WI, and a guest that tries to prod this register and
set ICC_SRE_EL1.SRE=1, must read back the value (which Linux already
does) to see if it succeeded, and will thus observe that ICC_SRE_EL1.SRE
was not set.
Add the simple trap handler in the sorted table of the system registers.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[ardb: added cp15 handling]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
memblock_is_region_reserved() returns true in the case of a partial
overlap, meaning that the current code fails to reserve the
non-overlapping portion.
This call was introduced as part of d1552ce449 "of/fdt: move
memreserve and dtb memory reservations into core" which went into
v3.16.
I observed this causing a Midway system with a buggy fdt (the header
declares itself to be larger than it really is) failing to boot
because the over-inflated size of the fdt was causing it to seem to
run into the swapper_pg_dir region, meaning the DT wasn't reserved.
The symptoms were failing to find an disks or network and failing to
boot.
However given the ambiguity of whether things like the initrd are
covered by /memreserve/ and similar I think it is best to also
register the region rather than just ignoring it.
Since memblock_reserve() handles overlaps just fine lets just warn and
carry on.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # v3.16+
Currently we just make sure vdd is off before suspending, but we don't
cancel the vdd off work. The work wil not touch vdd if
want_panel_vdd==false so in theory this is fine.
In the past that was perfectly fine since the vdd off work didn't do
anything when want_panel_vdd==false, so even if the work would have been
run during system resume before i915 has resumed, nothing would happen.
However since pps_lock() will now grab the power domain references before
it can check want_panel_vdd, we may end up toggling the power wells on/off
already before the driver has resumed. That is not really acceptable, so
cancel the vdd off work when suspending the encoder.
The problem appeared when pps_lock() was introduced in:
commit 773538e860
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:56 2014 +0300
drm/i915: Reset power sequencer pipe tracking when disp2d is off
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If no voltage supply regulators are defined for the UFS devices (assumed
they are always-on), ufshcd_config_vreg_load() can be called on
suspend/resume paths with vreg == NULL as hba->vreg_info.vcc* equal to
NULL, and it causes NULL pointer dereference.
This fixes it by making ufshcd_config_vreg_{h,l}pm noop when no regulators
are defined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When dynamic clk gating feature is enabled, delayed workqueue machanism
is used in order to detect certain period of inactivity. But there is no
guarantee that scheduled gating work is completed before module unloading.
So it can cause kernel crash by accessing memory after it was freed.
Fix it by cancelling clk gating and ungating works and ensure that its
execution is finished before module unloading.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull nfsd bugfixes from Bruce Fields:
"These fix one mishandling of the case when security labels are
configured out, and two races in the 4.1 backchannel code"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix slot wake up race in the nfsv4.1 callback code
SUNRPC: Fix locking around callback channel reply receive
nfsd: correctly define v4.2 support attributes
Pull aio fix from Ben LaHaise:
"Dirty page accounting fix for aio"
* git://git.kvack.org/~bcrl/aio-fixes:
aio: fix uncorrent dirty pages accouting when truncating AIO ring buffer
Pull powerpc fixes from Ben Herrenschmidt:
"This series fix a nasty issue with radeon adapters on powerpc servers,
it's all CC'ed stable and has the relevant maintainers ack's/reviews.
Basically, some (radeon) adapters have issues with MSI addresses above
1T (only support 40-bits). We had powerpc specific quirk but it only
listed a specific revision of an adapter that we shipped with our
machines and didn't properly handle the audio function which some
distros enable nowadays.
So we made the quirk generic and fixed both the graphic and audio
drivers properly to use it.
Without that, ppc64 server machines will crash at boot with a radeon
adapter.
Note: This has been brewing for a while, it just needed a last respin
which got delayed due to us moving ozlabs to a new location in town
and other such things taking priority"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Remove unused force_32bit_msi quirk
powerpc/pseries: Honor the generic "no_64bit_msi" flag
powerpc/powernv: Honor the generic "no_64bit_msi" flag
sound/radeon: Move 64-bit MSI quirk from arch to driver
gpu/radeon: Set flag to indicate broken 64-bit MSI
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
Pull a hwmon fix from Guenter Roeck:
"Fix hwmon registration problem in g762 driver"
* tag 'hwmon-for-linus-v3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (g762) fix call to devm_hwmon_device_register_with_groups()
Pull clock fixes from Mike Turquette:
"The fixes for the clock framework are all regressions in drivers, plus
a single fix in one of the basic clock templates. No fixes to the
core this time around.
As with most clock driver fixes these run the gamut from fixing a
build warning to fixing wrecked memory timings, with a little USB
tossed in for fun"
* tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux:
clk: pxa: fix pxa27x CCCR bit usage
clk-divider: Fix READ_ONLY when divider > 1
clk: qcom: Fix duplicate rbcpr clock name
clk: at91: usb: fix at91sam9x5 recalc, round and set rate
clk: at91: usb: fix at91rm9200 round and set rate
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ca777eff51 ("tcp: remove dst refcount false sharing for
prequeue mode") we have to relax check against skb dst in
tcp_v[46]_send_reset() if prequeue dropped the dst.
If a socket is provided, a full lookup was done to find this socket,
so the dst test can be skipped.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88191
Reported-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: ca777eff51 ("tcp: remove dst refcount false sharing for prequeue mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5195c14c8b.
If the conntrack clashes with an existing one, it is left out of
the unconfirmed list, thus, crashing when dropping the packet and
releasing the conntrack since golden rule is that conntracks are
always placed in any of the existing lists for traceability reasons.
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=88841
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Fix outer UDP checksums for IPv6 VXLAN tunnels
In testing against an older kernel I found a couple issues in the IPv6
VXLAN tunnel checksum logic for the outer UDP checksum.
First the default transitioned from using an outer checksum to not using
one. Second, sometime after that the checksum inputs were changed
resulting the checksum not being correct if it were computed.
These two issues prevented a ping from the newer kernel to the older one.
With these two changes applied I verified I was able to send traffic over
the VXLAN tunnel to a link partner on an older kernel.
The boolean flip fix can be submitted for 3.17 stable as well since the
patch that introduced the issue was included in that kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In "vxlan: Call udp_sock_create" there was a logic error that resulted in
the default for IPv6 VXLAN tunnels going from using checksums to not using
checksums. Since there is currently no support in iproute2 for setting
these values it means that a kernel after the change cannot talk over a IPv6
VXLAN tunnel to a kernel prior the change.
Fixes: 3ee64f3 ("vxlan: Call udp_sock_create")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP checksum calculation for VXLAN tunnels is currently using the
socket addresses instead of the actual packet source and destination
addresses. As a result the checksum calculated is incorrect in some
cases.
Also uh->check was being set twice, first it was set to 0, and then it is
set again in udp6_set_csum. This change removes the redundant assignment
to 0.
Fixes: acbf74a7 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions.")
Cc: Andy Zhou <azhou@nicira.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Only try to parse data as coming from trackpoint if firmware told us that
trackpoint is present.
Fixes commit caeb0d37fa
Reported-and-tested-by: Marcus Overhagen <marcus.overhagen@gmail.com>
Reported-and-tested-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
af_packet produces lots of these:
net/packet/af_packet.c:384:39: warning: incorrect type in return expression (different modifiers)
net/packet/af_packet.c:384:39: expected struct page [pure] *
net/packet/af_packet.c:384:39: got struct page *
this seems to be because sparse does not realize that _pure
refers to function, not the returned pointer.
Tweak code slightly to avoid the warning.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If xenvif_alloc() or xenbus_scanf() fail in backend_create_xenvif(),
xenbus is left in offline mode but netback_probe() reports success.
The patch implements propagation of error code for backend_create_xenvif().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a GPU reset we need to get pending page flip cleared out
since the ring contents are gone and flip will never complete
on its own. This used to work until the mmio vs. CS flip race
detection came about. That piece of code is looking for a
specific surface address in the SURFLIVE register, but as
a flip to that address may never happen the check may never
pass. So we should just skip the SURFLIVE and flip counter
checks when the GPU gets reset.
intel_display_handle_reset() tries to effectively complete
the flip anyway by calling .update_primary_plane(). But that
may not satisfy the conditions of the mmio vs. CS race
detection since there's no guarantee that a modeset didn't
sneak in between the GPU reset and intel_display_handle_reset().
Such a modeset will not wait for pending flips due to the ongoing GPU
reset, and then the primary plane updates performed by
intel_display_handle_reset() will already use the new surface
address, and thus the surface address the flip is waiting for
might never appear in SURFLIVE. The result is that the flip
will never complete and attempts to perform further page flips
will fail with -EBUSY.
During the GPU reset intel_crtc_has_pending_flip() will return
false regardless, so the deadlock with a modeset vs. the error
work acquiring crtc->mutex was avoided. And the reset_counter
check in intel_crtc_has_pending_flip() actually made this bug
even less severe since it allowed normal modesets to go through
even though there's a pending flip.
This is a regression introduced by me here:
commit 75f7f3ec60
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Apr 15 21:41:34 2014 +0300
drm/i915: Fix mmio vs. CS flip race on ILK+
Testcase: igt/kms_flip/flip-vs-panning-vs-hang
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
microMIPS and SmartMIPS can't be used together. This fixes the
following build problem:
Warning: the 32-bit microMIPS architecture does not support the `smartmips' extension
arch/mips/kernel/entry.S:90: Error: unrecognized opcode `mtlhx $24'
[...]
arch/mips/kernel/entry.S:109: Error: unrecognized opcode `mtlhx $24'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commits a951440971 ("MIPS: Netlogic: Support for XLP3XX on-chip SATA")
and fedfcb1137 ("MIPS: Netlogic: XLP9XX on-chip SATA support") added
ahci-init and ahci-init-xlp2 as objects to build when CONFIG_SATA_AHCI
is enabled.
If CONFIG_SATA_AHCI is made modular, these two files will also get built
as modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/ahci-init.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack"
[arch/mips/netlogic/xlp/ahci-init-xlp2.ko] undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/ahci-init-xlp2.ko]
undefined!
Just check whether CONFIG_SATA_AHCI is defined for this build, and if
that is the case, add these objects to the list of built-in object
files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1004165f34 ("MIPS: Netlogic: USB support for XLP") and then
commit 9eac3591e7 ("MIPS: Netlogic: Add support for USB on XLP2xx")
added usb-init and usb-init-xlp2 as objects to build when CONFIG_USB is
enabled.
If CONFIG_USB is made modular, these two files will also get built as
modules (obj-m), which will result in the following linking failure:
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init.ko] undefined!
ERROR: "nlm_nodes" [arch/mips/netlogic/xlp/usb-init-xlp2.ko] undefined!
ERROR: "nlm_set_pic_extra_ack" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "xlp_socdev_to_node" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
ERROR: "nlm_io_base" [arch/mips/netlogic/xlp/usb-init-xlp2.ko]
undefined!
Just check whether CONFIG_USB is defined for this build, and if that is
the case, add these objects to the list of built-in object files.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: ganesanr@broadcom.com
Cc: jchandra@broadcom.com
Patchwork: https://patchwork.linux-mips.org/patch/7854/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The save_fp_context & restore_fp_context pointers were being assigned
to the wrong variables if either:
- The kernel is configured for UP & runs on a system without an FPU,
since b2ead52828 "MIPS: Move & rename
fpu_emulator_{save,restore}_context".
- The kernel is configured for EVA, since ca750649e0 "MIPS: kernel:
signal: Prevent save/restore FPU context in user memory".
This would lead to FP context being clobbered incorrectly when setting
up a sigcontext, then the garbage values being saved uselessly when
returning from the signal.
Fix by swapping the pointer assignments appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8230/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the Config6/FLTBP bit to set the probability of a TLBWR
instruction to hit the FTLB or the VTLB. A value of 0 (which may be
the default value on certain cores, such as proAptiv or P5600)
means that a TLBWR instruction will never hit the VTLB which
leads to performance limitations since it effectively decreases
the number of available TLB slots.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8368/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit de8974e3f7 ("MIPS: asm: r4kcache: Add EVA cache flushing
functions") added cache function for EVA using the cachee instruction.
However, it didn't add a case for the protected_writeback_dcache_line.
mips_dsemul() calls r4k_flush_cache_sigtramp() which in turn uses
the protected_writeback_dcache_line() to flush the trampoline code
back to memory. This used the wrong "cache" instruction leading to
random userland crashes on non-FPU cores.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is now fully replaced with the generic "no_64bit_msi" one
that is set by the respective drivers directly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
A number of radeon cards have a HW limitation causing them to be
unable to generate the full 64-bit of address bits for MSIs. This
breaks MSIs on some platforms such as POWER machines.
We used to have a powerpc specific quirk to address that on a
single card, but this doesn't scale very well, this is better
put under control of the drivers who know precisely what a given
HW revision can do.
We now have a generic quirk in the PCI code. We should set it
appropriately for all radeon's from the audio driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
Some radeon ASICs don't support all 64 address bits of MSIs despite
advertising support for 64-bit MSIs in their configuration space.
This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can
be assigned with some of the high address bits set.
This makes use of the newly introduced "no_64bit_msi" flag in structure
pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs
on those adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: <stable@vger.kernel.org>
---
Adding Alex's review tag. Patch to the driver is identical to the
reviewed one, I dropped the arch/powerpc hunk rewrote the subject
and cset comment.
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():
hlist_for_each_entry_rcu(t, head, hash_node) {
if (local == t->parms.iph.saddr &&
remote == t->parms.iph.daddr &&
link == t->parms.link &&
==> type == t->dev->type &&
ip_tunnel_key_match(&t->parms, flags, key))
break;
}
the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD b2c21067 PUD b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008] ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008] ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008] ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008] [<ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008] [<ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008] [<ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008] [<ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008] [<ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008] [<ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008] [<ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008] [<ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008] [<ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008] [<ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008] [<ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....
modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti
do that one or more times, kernel will panic.
fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris bisected a NULL pointer deference in task_sched_runtime() to
commit 6e998916df 'sched/cputime: Fix clock_nanosleep()/clock_gettime()
inconsistency'.
Chris observed crashes in atop or other /proc walking programs when he
started fork bombs on his machine. He assumed that this is a new exit
race, but that does not make any sense when looking at that commit.
What's interesting is that, the commit provides update_curr callbacks
for all scheduling classes except stop_task and idle_task.
While nothing can ever hit that via the clock_nanosleep() and
clock_gettime() interfaces, which have been the target of the commit in
question, the author obviously forgot that there are other code paths
which invoke task_sched_runtime()
do_task_stat(()
thread_group_cputime_adjusted()
thread_group_cputime()
task_cputime()
task_sched_runtime()
if (task_current(rq, p) && task_on_rq_queued(p)) {
update_rq_clock(rq);
up->sched_class->update_curr(rq);
}
If the stats are read for a stomp machine task, aka 'migration/N' and
that task is current on its cpu, this will happily call the NULL pointer
of stop_task->update_curr. Ooops.
Chris observation that this happens faster when he runs the fork bomb
makes sense as the fork bomb will kick migration threads more often so
the probability to hit the issue will increase.
Add the missing update_curr callbacks to the scheduler classes stop_task
and idle_task. While idle tasks cannot be monitored via /proc we have
other means to hit the idle case.
Fixes: 6e998916df 'sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency'
Reported-by: Chris Mason <clm@fb.com>
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge x86-64 iret fixes from Andy Lutomirski:
"This addresses the following issues:
- an unrecoverable double-fault triggerable with modify_ldt.
- invalid stack usage in espfix64 failed IRET recovery from IST
context.
- invalid stack usage in non-espfix64 failed IRET recovery from IST
context.
It also makes a good but IMO scary change: non-espfix64 failed IRET
will now report the correct error. Hopefully nothing depended on the
old incorrect behavior, but maybe Wine will get confused in some
obscure corner case"
* emailed patches from Andy Lutomirski <luto@amacapital.net>:
x86_64, traps: Rework bad_iret
x86_64, traps: Stop using IST for #SS
x86_64, traps: Fix the espfix64 #DF fixup and rewrite it in C
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aaf
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes this week:
- A set of clock fixes for shmobile platforms
- A fix for tegra that moves serial port labels to be per board.
We're choosing to merge this for 3.18 because the labels will start
being parsed in 3.19, and without this change serial port numbers
that used to be stable since the dawn of time will change numbers.
- A few other DT tweaks for Tegra.
- A fix for multi_v7_defconfig that makes it stop spewing cpufreq
errors on Arndale (Exynos)"
* tag 'armsoc-for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: fix failure setting CPU voltage by enabling dependent I2C controller
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
ARM: shmobile: r8a7740 legacy: Correct IIC0 parent clock
ARM: shmobile: r8a7740 legacy: Add missing INTCA clock for irqpin module
ARM: shmobile: r8a7790: Fix SD3CKCR address
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Pull percpu fix from Tejun Heo:
"This contains one patch to fix a race condition which can lead to
percpu_ref using a percpu pointer which is corrupted with a set DEAD
bit. The bug was introduced while separating out the ATOMIC mode flag
from the DEAD flag. The fix is pretty straight forward.
I just committed the patch to the percpu tree but am sending out the
pull request early as I'll be on vacation for a week. The patch
should be fairly safe and while the latency will be higher I'll be
checking emails"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu-ref: fix DEAD flag contamination of percpu pointer
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on a different issue, I noticed an annoying use
after free bug on my machine when unloading the ixgbe driver:
[ 8642.318797] ixgbe 0000:02:00.1: removed PHC on p2p2
[ 8642.742716] ixgbe 0000:02:00.1: complete
[ 8642.743784] BUG: unable to handle kernel paging request at ffff8807d3740a90
[ 8642.744828] IP: [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[ 8642.745886] PGD 20c6067 PUD 81c1f6067 PMD 81c15a067 PTE 80000007d3740060
[ 8642.746956] Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
[ 8642.748039] Modules linked in: [...]
[ 8642.752929] CPU: 1 PID: 1225 Comm: rmmod Not tainted 3.18.0-rc2+ #49
[ 8642.754203] Hardware name: Supermicro X10SLM-F/X10SLM-F, BIOS 1.1b 11/01/2013
[ 8642.755505] task: ffff8807e34d3fe0 ti: ffff8807b7204000 task.ti: ffff8807b7204000
[ 8642.756831] RIP: 0010:[<ffffffffa01c77dc>] [<ffffffffa01c77dc>] ixgbe_remove+0xfc/0x1b0 [ixgbe]
[...]
[ 8642.774335] Stack:
[ 8642.775805] ffff8807ee824098 ffff8807ee824098 ffffffffa01f3000 ffff8807ee824000
[ 8642.777326] ffff8807b7207e18 ffffffff8137720f ffff8807ee824098 ffff8807ee824098
[ 8642.778848] ffffffffa01f3068 ffff8807ee8240f8 ffff8807b7207e38 ffffffff8144180f
[ 8642.780365] Call Trace:
[ 8642.781869] [<ffffffff8137720f>] pci_device_remove+0x3f/0xc0
[ 8642.783395] [<ffffffff8144180f>] __device_release_driver+0x7f/0xf0
[ 8642.784876] [<ffffffff814421f8>] driver_detach+0xb8/0xc0
[ 8642.786352] [<ffffffff814414a9>] bus_remove_driver+0x59/0xe0
[ 8642.787783] [<ffffffff814429d0>] driver_unregister+0x30/0x70
[ 8642.789202] [<ffffffff81375c65>] pci_unregister_driver+0x25/0xa0
[ 8642.790657] [<ffffffffa01eb38e>] ixgbe_exit_module+0x1c/0xc8e [ixgbe]
[ 8642.792064] [<ffffffff810f93a2>] SyS_delete_module+0x132/0x1c0
[ 8642.793450] [<ffffffff81012c61>] ? do_notify_resume+0x61/0xa0
[ 8642.794837] [<ffffffff816d2029>] system_call_fastpath+0x12/0x17
The issue is that test_and_set_bit() done on adapter->state is being
performed *after* the netdevice has been freed via free_netdev().
When netdev is being allocated on initialization time, it allocates
a private area, here struct ixgbe_adapter, that resides after the
net_device structure. In ixgbe_probe(), the device init routine,
we set up the adapter after alloc_etherdev_mq() on the private area
and add a reference for the pci_dev as well via pci_set_drvdata().
Both in the error path of ixgbe_probe(), but also on module unload
when ixgbe_remove() is being called, commit 41c62843eb ("ixgbe:
Fix rcu warnings induced by LER") accesses adapter after free_netdev().
The patch stores the result in a bool and thus fixes above oops on my
side.
Fixes: 41c62843eb ("ixgbe: Fix rcu warnings induced by LER")
Cc: stable <stable@vger.kernel.org>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IXGBE adapter seems to require that VLAN filtering be enabled if
VMDQ or SRIOV are enabled. When those functions are disabled,
VLAN filtering may be disabled in promiscuous mode.
Prior to commit a9b8943ee1 ("ixgbe: remove vlan_filter_disable
and enable functions")
The logic was correct. However, after the commit the logic
got reversed and VLAN filtered in now turned on when VMDQ/SRIOV
is disabled.
This patch changes the condition to enable hw vlan filtered
when VMDQ or SRIOV is enabled.
Fixes: a9b8943ee1 ("ixgbe: remove vlan_filter_disable and enable functions")
Cc: stable <stable@vger.kernel.org>
CC: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SKB_GSO_TCPV4 to the list of supported GSO types handled by
the IPv6 GSO offloads. Without this change VXLAN tunnels running over IPv6
do not currently handle IPv4 TCP TSO requests correctly and end up handing
the non-segmented frame off to the device.
Below is the before and after for a simple netperf TCP_STREAM test between
two endpoints tunneling IPv4 over a VXLAN tunnel running on IPv6 on top of
a 1Gb/s network adapter.
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.29 0.88 Before
87380 16384 16384 10.03 895.69 After
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs deadlock fix from Chris Mason:
"This has a fix for a long standing deadlock that we've been trying to
nail down for a while. It ended up being a bad interaction with the
fair reader/writer locks and the order btrfs reacquires locks in the
btree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix lockups from btrfs_clear_path_blocking
While decoupling ATOMIC and DEAD flags, f47ad45784 ("percpu_ref:
decouple switching to percpu mode and reinit") updated
__ref_is_percpu() so that it only tests ATOMIC flag to determine
whether the ref is in percpu mode or not; however, while DEAD implies
ATOMIC, the two flags are set separately during percpu_ref_kill() and
if __ref_is_percpu() races percpu_ref_kill(), it may see DEAD w/o
ATOMIC. Because __ref_is_percpu() returns @ref->percpu_count_ptr
value verbatim as the percpu pointer after testing ATOMIC, the pointer
may now be contaminated with the DEAD flag.
This can be fixed by clearing the flag bits before returning the
pointer which was the fix proposed by Shaohua; however, as DEAD
implies ATOMIC, we can just test for both flags at once and avoid the
explicit masking.
Update __ref_is_percpu() so that it tests that both ATOMIC and DEAD
are clear before returning @ref->percpu_count_ptr as the percpu
pointer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-Reviewed-by: Shaohua Li <shli@kernel.org>
Link: http://lkml.kernel.org/r/995deb699f5b873c45d667df4add3b06f73c2c25.1416638887.git.shli@kernel.org
Fixes: f47ad45784 ("percpu_ref: decouple switching to percpu mode and reinit")
Pull timer fix from Thomas Gleixner:
"A single bugfix for an init order problem in the sun4i subarch
clockevents code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevent: sun4i: Fix race condition in the probe code
Pull vfs fixes from Al Viro:
"Assorted fixes, most in overlayfs land"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: ovl_dir_fsync() cleanup
ovl: update MAINTAINERS
ovl: pass dentry into ovl_dir_read_merged()
ovl: use lockless_dereference() for upperdentry
ovl: allow filenames with comma
ovl: fix race in private xattr checks
ovl: fix remove/copy-up race
ovl: rename filesystem type to "overlay"
isofs: avoid unused function warning
vfs: fix reference leak in d_prune_aliases()
commit 6d9939f651 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f651 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre 6d9939f651 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Cc: <stable@vger.kernel.org> #v2.6.35
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly, so we need to fall-back to usb-storage for these.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for v3.18-rc6
Three fixes for bugs related to TTY error reporting, which can to lead
to data being dropped by the line discipline.
Included is also some new device ids for ftdi_sio and cp210x.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull networking fixes from David Miller:
1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.
2) nf_nat_range is not fully initialized and this is copied back to
userspace, from Daniel Borkmann.
3) Fix read past end of b uffer in netfilter ipset, also from Dan
Carpenter.
4) Signed integer overflow in ipv4 address mask creation helper
inet_make_mask(), from Vincent BENAYOUN.
5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
properly describe the device's capabilities, from Joe Stringer.
6) Fix memory leaks and checksum miscalculations in openvswitch, from
Pravin B SHelar and Jesse Gross.
7) FIB rules passes back ambiguous error code for unreachable routes,
making behavior confusing for userspace. Fix from Panu Matilainen.
8) ieee802154fake_probe() doesn't release resources properly on error,
from Alexey Khoroshilov.
9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.
10) Fix access of stale slave pointers in bonding code, from Nikolay
Aleksandrov.
11) Fix stack info leak in PPP pptp code, from Mathias Krause.
12) Cure locking bug in IPX stack, from Jiri Bohac.
13) Revert SKB fclone memory freeing optimization that is racey and can
allow accesses to freed up memory, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
tcp: Restore RFC5961-compliant behavior for SYN packets
net: Revert "net: avoid one atomic operation in skb_clone()"
virtio-net: validate features during probe
cxgb4 : Fix DCB priority groups being returned in wrong order
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
openvswitch: Don't validate IPv6 label masks.
pptp: fix stack info leak in pptp_getname()
brcmfmac: don't include linux/unaligned/access_ok.h
cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
ipv6: delete protocol and unregister rtnetlink when cleanup
net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
mac80211: minstrel_ht: fix a crash in rate sorting
vxlan: Inline vxlan_gso_check().
can: m_can: update to support CAN FD features
can: m_can: fix incorrect error messages
can: m_can: add missing delay after setting CCCR_INIT bit
can: m_can: fix not set can_dlc for remote frame
can: m_can: fix possible sleep in napi poll
can: m_can: add missing message RAM initialization
...
Pull drm fixes from Dave Airlie:
"Just two radeon and two intel fixes: endian and regression fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix endian swapping in vbios fetch for tdp table
drm/radeon: disable native backlight control on pre-r6xx asics (v2)
drm/i915: Kick fbdev before vgacon
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
Pull sound fixes from Takashi Iwai:
"This batch ended up as a relatively high volume due to pending ASoC
fixes. But most of fixes there are trivial and/or device- specific
fixes and quirks, so safe to apply. The only (ASoC) core fixes are
the DPCM race fix and the machine-driver matching fix for
componentization"
* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix the mic mute led problem for Latitude E5550
ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
ASoC: sgtl5000: Fix SMALL_POP bit definition
ASoC: cs42l51: re-hook of_match_table pointer
ASoC: rt5670: change dapm routes of PLL connection
ASoC: rt5670: correct the incorrect default values
ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
ASoC: max98090: Correct pclk divisor settings
ASoC: dpcm: Fix race between FE/BE updates and trigger
ASoC: Fix snd_soc_find_dai() matching component by name
ASoC: rsnd: remove unsupported PAUSE flag
ASoC: fsi: remove unsupported PAUSE flag
ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump
Pull ACPI power management fix from Rafael Wysocki:
"This is just a one-liner fixing a regression introduced in 3.13 that
broke system suspend on some Chromebooks.
On those machines there are ACPI device objects for some I2C devices
that can wake up the system from sleep states, but that is done via a
platform-specific mechanism and the ACPI objects don't contain any
wakeup-related information. When we started to use ACPI power
management with those devices (which happened during the 3.13 cycle),
their configuration confused the ACPI PM layer that returned error
codes from suspend callbacks for them causing system suspend to fail.
However, the ACPI PM layer can safely ignore the wakeup setting from a
device driver if the ACPI object corresponding to the device in
question doesn't contain wakeup information in which case the driver
itself is responsible for setting up the device for system wakeup"
* tag 'pm+acpi-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Ignore wakeup setting if the ACPI companion can't wake up
Pull devicetree fixes from Rob Herring:
"DeviceTree fixes for 3.18:
- two fixes for OF selftest code
- fix for PowerPC address parsing to disable work-around except on
old PowerMACs
- fix a crash when earlycon is enabled, but no device is found
- DT documentation fixes and missing vendor prefixes
All but the doc updates are also for stable"
* tag 'devicetree-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/selftest: Fix testing when /aliases is missing
of/selftest: Fix off-by-one error in removal path
documentation: pinctrl bindings: Fix trivial typo 'abitrary'
devicetree: bindings: Add vendor prefix for Micron Technology, Inc.
of: Add vendor prefix for Chips&Media, Inc.
of/base: Fix PowerPC address parsing hack
devicetree: vendor-prefixes.txt: fix whitespace
of: Fix crash if an earlycon driver is not found
of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
of: Spelling s/stucture/structure/
devicetree: bindings: add sandisk to the vendor prefixes
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
PAE kernels, an APM X-Gene problem (it depended on a generic change we
removed before merging), a fix for my hotplug device configuration
changes, and a devicetree documentation update.
Resource management:
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug:
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver:
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene:
- Assign resources to bus before adding new devices (Duc Dang)"
* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
PCI: Apply _HPX Link Control settings to all devices with a link
PCI: Add missing DT binding for "linux,pci-domain" property
PCI: xgene: Assign resources to bus before adding new devices
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target-pending fixes queued for v3.18-rc6.
The highlights include:
- target-core OOPs fix with tcm_qla2xxx + vxworks FC initiators +
zero length SCSI commands having a transfer direction set. (Roland
+ Craig Watson)
- vhost-scsi OOPs fix to explicitly prevent WWPN endpoint configfs
group removal while qemu still has an active reference. (Paolo +
nab)
- ib_srpt fix for RDMA hardware with lower srp_sq_size limits.
(Bart)
- two ib_isert work-arounds for running on ocrdma hardware (Or + Sagi
+ Chris)
- iscsi-target discovery portal typo + SPC-3 PR Preempt SA key
matching fix (Steve)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
IB/isert: Adjust CQ size to HW limits
target: return CONFLICT only when SA key unmatched
iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
ib_isert: Add max_send_sge=2 minimum for control PDU responses
srp-target: Retry when QP creation fails with ENOMEM
iscsi-target: return the correct port in SendTargets
vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
target: Don't call TFO->write_pending if data_length == 0
Pull dmaengine fixes from Vinod Koul:
"We have couple of fixes for dmaengine queued up:
- dma mempcy fix for dma configuration of sun6i by Maxime
- pl330 fixes: First the fixing allocation for data buffers by Liviu
and then Jon's fixe for fifo width and usage"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: Fix allocation size for PL330 data buffer depth.
dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
dmaengine: pl330: Align DMA memcpy operations to MFIFO width
dmaengine: sun6i: Fix memcpy operation
Pull MIPS fixes from Ralf Baechle:
"More 3.18 fixes for MIPS:
- backtraces were not quite working on on 64-bit kernels
- loongson needs a different cache coherency setting
- Loongson 3 is a MIPS64 R2 version but due to erratum we treat is an
older architecture revision.
- fix build errors due to undefined references to __node_distances
for certain configurations.
- fix instruction decodig in the jump label code.
- for certain configurations copy_{from,to}_user destroy the content
of $3 so that register needs to be marked as clobbed by the calling
code.
- Hardware Table Walker fixes.
- fill the delay slot of the last instruction of memcpy otherwise
whatever ends up there randomly might have undesirable effects.
- ensure get_user/__get_user always zero the variable to be read even
in case of an error"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: jump_label.c: Handle the microMIPS J instruction encoding
MIPS: jump_label.c: Correct the span of the J instruction
MIPS: Zero variable read by get_user / __get_user in case of an error.
MIPS: lib: memcpy: Restore NOP on delay slot before returning to caller
MIPS: tlb-r4k: Add missing HTW stop/start sequences
MIPS: asm: uaccess: Add v1 register to clobber list on EVA
MIPS: oprofile: Fix backtrace on 64-bit kernel
MIPS: Loongson: Set Loongson-3's ISA level to MIPS64R1
MIPS: Loongson: Fix the write-combine CCA value setting
MIPS: IP27: Fix __node_distances undefined error
MIPS: Loongson3: Fix __node_distances undefined error
Pull powerpc fix from Michael Ellerman:
"One fix from Scott, he says:
This patch fixes a crash (introduced in v3.18-rc1) in the FSL MSI driver
when threaded IRQs are enabled"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/fsl_msi: mark the msi cascade handler IRQF_NO_THREAD
Pull x86 fixes from Thomas Gleixner:
"Misc fixes:
- gold linker build fix
- noxsave command line parsing fix
- bugfix for NX setup
- microcode resume path bug fix
- _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
lockup thread"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
x86, kaslr: Handle Gold linker for finding bss/brk
x86, mm: Set NX across entire PMD at boot
x86, microcode: Update BSPs microcode on resume
x86: Require exact match for 'noxsave' command line option
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: two NUMA fixes, two cputime fixes and an RCU/lockdep fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency
sched/cputime: Fix cpu_timer_sample_group() double accounting
sched/numa: Avoid selecting oneself as swap target
sched/numa: Fix out of bounds read in sched_init_numa()
sched: Remove lockdep check in sched_move_task()
Pull perf fixes from Ingo Molnar:
"Misc fixes: two Intel uncore driver fixes, a CPU-hotplug fix and a
build dependencies fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix boot crash on SBOX PMU on Haswell-EP
perf/x86/intel/uncore: Fix IRP uncore register offsets on Haswell EP
perf: Fix corruption of sibling list with hotplug
perf/x86: Fix embarrasing typo
Pull core fix from Ingo Molnar:
"Fix GENMASK macro shift overflow"
Nobody seems to currently use GENMASK() to fill every single last bit
(which is what overflows) in-tree, and gcc would warn about it, so we
have that going for us. But apparently there are pending changes that
want this.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bitops: Fix shift overflow in GENMASK macros
Commit c3ae62af8e ("tcp: should drop incoming frames without ACK
flag set") was created to mitigate a security vulnerability in which a
local attacker is able to inject data into locally-opened sockets by
using TCP protocol statistics in procfs to quickly find the correct
sequence number.
This broke the RFC5961 requirement to send a challenge ACK in response
to spurious RST packets, which was subsequently fixed by commit
7b514a886b ("tcp: accept RST without ACK flag").
Unfortunately, the RFC5961 requirement that spurious SYN packets be
handled in a similar manner remains broken.
RFC5961 section 4 states that:
... the handling of the SYN in the synchronized state SHOULD be
performed as follows:
1) If the SYN bit is set, irrespective of the sequence number, TCP
MUST send an ACK (also referred to as challenge ACK) to the remote
peer:
<SEQ=SND.NXT><ACK=RCV.NXT><CTL=ACK>
After sending the acknowledgment, TCP MUST drop the unacceptable
segment and stop processing further.
By sending an ACK, the remote peer is challenged to confirm the loss
of the previous connection and the request to start a new connection.
A legitimate peer, after restart, would not have a TCB in the
synchronized state. Thus, when the ACK arrives, the peer should send
a RST segment back with the sequence number derived from the ACK
field that caused the RST.
This RST will confirm that the remote peer has indeed closed the
previous connection. Upon receipt of a valid RST, the local TCP
endpoint MUST terminate its connection. The local TCP endpoint
should then rely on SYN retransmission from the remote end to
re-establish the connection.
This patch lets SYN packets through the discard added in c3ae62af8e,
so that spurious SYN packets are properly dealt with as per the RFC.
The challenge ACK is sent unconditionally and is rate-limited, so the
original vulnerability is not reintroduced by this patch.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions cpufreq_cooling_unregister() and thermal_zone_device_unregister()
test whether their argument is NULL and then return immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Prevents build warning:
st_thermal.c:278:12:
warning: ‘st_thermal_suspend’ defined but not used [-Wunused-function]
st_thermal.c:286:12:
warning: ‘st_thermal_resume’ defined but not used [-Wunused-function]
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The toggle bit shouldn't be cleared before the toggle value is calculated.
This should probably go into 3.17.x as well.
Fixes: 120703f9eb ([media] rc-core: document the protocol type)
Cc: stable@vger.kernel.org # For v3.17
Tested-by: Stephan Raue <mailinglists@openelec.tv>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I'm using the new Open Source Group address for my upstream work.
While the other email is still valid, it is better for me to receive
patches via the new address.
So, replace it everywhere inside MAINTAINERS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The IRQs have to be acknowledged before they are serviced, otherwise some events
may be skipped. Also, acknowledging IRQs just before returning from the handler
doesn't leave enough time for the device to deassert the INTx line, and for
bridges to propagate this change. This resulted in twice the IRQ rate on ARMv6
dual core CPU.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Acked-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Tested-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"The biggest change is to rename the filesystem from "overlayfs" to "overlay".
This will allow legacy overlayfs to be easily carried by distros alongside the
new mainline one. Also fix a couple of copy-up races and allow escaping comma
character in filenames."
The last bit is about commas in pathname mount options...
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes XMOS DSD sample format to DSD_U32_BE and also adds
DSD_U16_BE and DSD_U32_BE sample formats.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Acked-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 6e80e3d875 ("ARM: exynos_defconfig: Enable MAX77802")
enabled support for the max77802 regulators but the PMIC also
has a Real-Time-Clock (RTC) and 2-channel 32kHz clock outputs.
Enable the kernel config options to have the drivers for these
devices built-in since they are present in many Exynos boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If the Designware core is configured with IC_EMPTYFIFO_HOLD_MASTER_EN
set to zero, allowing the TX FIFO to become empty causes a STOP
condition to be generated on the I2C bus. If the transmit FIFO
threshold is set too high, an erroneous STOP condition can be
generated on long transfers - particularly where the interrupt
latency is extended.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 1d7afc9594 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Cc: <stable@vger.kernel.org> # v3.7+
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two bugfixes for your net tree, they are:
1) Validate netlink group from nfnetlink to avoid an out of bound array
access. This should only happen with superuser priviledges though.
Discovered by Andrey Ryabinin using trinity.
2) Don't push ethernet header before calling the netfilter output hook
for multicast traffic, this breaks ebtables since it expects to see
skb->data pointing to the network header, patch from Linus Luessing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-20
Please full this little batch of fixes intended for the 3.18 stream!
For the mac80211 patch, Johannes says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
On top of that...
Ben Greear fixes an ath9k regression in which a BSSID mask is
miscalculated.
Dmitry Torokhov corrects an error handling routing in brcmfmac which
was checking an unsigned variable for a negative value.
Johannes Berg avoids a build problem in brcmfmac for arches where
linux/unaligned/access_ok.h and asm/unaligned.h conflict.
Mathy Vanhoef addresses another brcmfmac issue so as to eliminate a
use-after-free of the URB transfer buffer if a timeout occurs.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Peer priority groups were being reversed, but this was missed in the previous
fix sent out for this issue.
v2 : Previous patch was doing extra unnecessary work, result is the same.
Please ignore previous patch
Fixes : ee7bc3cdc2 ('cxgb4 : dcb open-lldp interop fixes')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an old regression introduced by commit
b0d0d915 (ipx: remove the BKL).
When a recvmsg syscall blocks waiting for new data, no data can be sent on the
same socket with sendmsg because ipx_recvmsg() sleeps with the socket locked.
This breaks mars-nwe (NetWare emulator):
- the ncpserv process reads the request using recvmsg
- ncpserv forks and spawns nwconn
- ncpserv calls a (blocking) recvmsg and waits for new requests
- nwconn deadlocks in sendmsg on the same socket
Commit b0d0d915 has simply replaced BKL locking with
lock_sock/release_sock. Unlike now, BKL got unlocked while
sleeping, so a blocking recvmsg did not block a concurrent
sendmsg.
Only keep the socket locked while actually working with the socket data and
release it prior to calling skb_recv_datagram().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace doesn't provide a mask, OVS datapath generates a fully
unwildcarded mask for the flow by copying the flow and setting all bits
in all fields. For IPv6 label, this creates a mask that matches on the
upper 12 bits, causing the following error:
openvswitch: netlink: Invalid IPv6 flow label value (value=ffffffff, max=fffff)
This patch ignores the label validation check for masks, avoiding this
error.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pptp_getname() only partially initializes the stack variable sa,
particularly only fills the pptp part of the sa_addr union. The code
thereby discloses 16 bytes of kernel stack memory via getsockname().
Fix this by memset(0)'ing the union before.
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix one regression and one endian issue.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix endian swapping in vbios fetch for tdp table
drm/radeon: disable native backlight control on pre-r6xx asics (v2)
Existing code updates cupfreq policy only while executing
cpufreq_apply_cooling() function (i.e. when notify_device != NOTIFY_INVALID).
It doesn't apply constraints when cpufreq policy update happens from any other
place but it should update the cpufreq policy with thermal constraints every
time when there is a cpufreq policy update, to keep state of
cpufreq_cooling_device and max_feq of cpufreq policy in sync. For instance
while resuming cpufreq updates cpufreq_policy and it restores default
policy->usr_policy values irrespective of cooling device's cpufreq_state since
notification gets missed because (notify_device == NOTIFY_INVALID).
Another problem, is that userspace is able to change max_freq irrespective of
cooling device's state, as notification gets missed.
This patch modifies code to maintain a global cpufreq_dev_list and applies
constraints of all matching cooling devices for policy's cpu when there is any
policy update(ends up applying the lowest max_freq among the matching cpu
cooling devices).
This patch also removes redundant check (max_freq > policy->user_policy.max),
as cpufreq framework takes care of user_policy constraints already where ever
required, otherwise its causing an issue while increasing max_freq in normal
scenerio as it restores max_freq with policy->user_policy.max which is old
(smaller) value.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
snd_nativeinstruments_control_get() uses a stack as a buffer for
usb_control_msg(), but it's basically not allowed. Replace the call
with a safer helper, snd_usb_ctl_msg(), instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
This issue was revealed by kbuild testing
when <asm/unaligned.h> was added in <linux/ieee80211.h>
resulting in redefinition of get_unaligned_be16 (and
probably others).
Cc: stable@vger.kernel.org # v3.17
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes newly introduced static checker warning in
ufshcd_parse_clock_info, introduced by UFS power management series.
Warning:
drivers/scsi/ufs/ufshcd-pltfrm.c:138 ufshcd_parse_clock_info()
warn: passing devm_ allocated variable to kfree. 'clkfreq'
To fix it we remove the kfree(clkfreq) statement.
In addition we removed the redundant goto label.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes newly introduced static checker warning in
__ufshcd_setup_clocks, introduced by UFS power management series.
Warning:
drivers/scsi/ufs/ufshcd.c:4474 __ufshcd_setup_clocks()
warn: we tested 'ret' before and it was 'false'
To fix it we remove the (!ret) from the condition.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes newly introduced sparse warning in
ufshcd_system_suspend, introduced by UFS power management series.
Sparse warning:
drivers/scsi/ufs/ufshcd.c:5118 ufshcd_system_suspend()
error: we previously assumed 'hba' could be null (see line 5089)
To fix it, we return 0 in case HBA is not initialized or is
not powered.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just use the acpi interface. That's what windows uses on this
generation and it's the only thing that seems to work reliably
on these generation parts.
You can still force the native backlight interface by setting
radeon.backlight=1
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=88501
v2: merge into above if/else block
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
After link start-up power mode will always be PWM G1. This is not
reflected in the pwr_info struct which will keep the previous values.
Since ufshcd_change_power_mode() tries to avoid unnecessary power mode
change if the requested power mode and current power mode are same,
power mode change won't execute again after driver initialization.
This patch solves the problem by setting pwr_info to PWM G1 after link
start-up.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS driver adds three well known LUs in the initialization, but those
reference counts are not decremented, so it makes ufshcd module
impossible to unload.
This fixes it by putting scsi_device_put() in the initalization, and in
order to protect concurrent access to hba->sdev_ufs_device (UFS Device
W-LU) from manual delete, increment the reference count while requesting
device power mode setting.
The rest of W-LUs (hba->sdev_boot and hba->sdev_rpmb) are not directly
used from driver, so these references in struct ufs_hba are removed.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Intel Multi-Flex LUNs choke on REPORT SUPPORTED OPERATION CODES
resulting in sd_mod hanging for several minutes on startup.
The issue was introduced with WRITE SAME discovery heuristics.
Fixes: 5db44863b6 ("[SCSI] sd: Implement support for WRITE SAME")
Signed-off-by: Christian Sünkenberg <christian.suenkenberg@hfg-karlsruhe.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Check against !OVL_PATH_LOWER instead of OVL_PATH_MERGE. For a copied up
directory the two are currently equivalent.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Pass dentry into ovl_dir_read_merged() insted of upperpath and lowerpath.
This cleans up callers and paves the way for multi-layer directory reads.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Xattr operations can race with copy up. This does not matter as long as
we consistently fiter out "trunsted.overlay.opaque" attribute on upper
directories.
Previously we checked parent against OVL_PATH_MERGE. This is too general,
and prone to race with copy-up. I.e. we found the parent to be on the
lower layer but ovl_dentry_real() would return the copied-up dentry,
possibly with the "opaque" attribute.
So instead use ovl_path_real() and decide to filter the attributes based on
the actual type of the dentry we'll use.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
ovl_remove_and_whiteout() needs to check if upper dentry exists or not
after having locked upper parent directory.
Previously we used a "type" value computed before locking the upper parent
directory, which is susceptible to racing with copy-up.
There's a similar check in ovl_check_empty_and_clear(). This one is not
actually racy, since copy-up doesn't change the "emptyness" property of a
directory. Add a comment to this effect, and check the existence of upper
dentry locally to make the code cleaner.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Some distributions carry an "old" format of overlayfs while mainline has a
"new" format.
The distros will possibly want to keep the old overlayfs alongside the new
for compatibility reasons.
To make it possible to differentiate the two versions change the name of
the new one from "overlayfs" to "overlay".
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Andy Whitcroft <apw@canonical.com>
The /aliases node isn't always present in the device tree, but the
unittest code assumes that /aliases is there. Add a check when inserting
the testcase data to see if of_aliases needs to be updated, and undo the
settings when the nodes are removed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org>
isert has an issue of trying to create a CQ with more CQEs than are
supported by the hardware, that currently results in failures during
isert_device creation during first session login.
This is the isert version of the patch that Minh Tran submitted for
iser, and is simple a workaround required to function with existing
ocrdma hardware.
Signed-off-by: Chris Moore <chris.moore@emulex.com>
Reviewied-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
two regression fixes.
* tag 'drm-intel-fixes-2014-11-19' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Kick fbdev before vgacon
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
As reported by Dmitry, on some Chromebooks there are devices with
corresponding ACPI objects and with unusual system wakeup
configuration. Namely, they technically are wakeup-capable, but the
wakeup is handled via a platform-specific out-of-band mechanism and
the ACPI PM layer has no information on the wakeup capability. As
a result, device_may_wakeup(dev) called from acpi_dev_suspend_late()
returns 'true' for those devices, but the wakeup.flags.valid flag is
unset for the corresponding ACPI device objects, so acpi_device_wakeup()
reproducibly fails for them causing acpi_dev_suspend_late() to return
an error code. The entire system suspend is then aborted and the
machines in question cannot suspend at all.
Address the problem by ignoring the device_may_wakeup(dev) return
value in acpi_dev_suspend_late() if the ACPI companion of the device
being handled has wakeup.flags.valid unset (in which case it is clear
that the wakeup is supposed to be handled by other means).
This fixes a regression introduced by commit a76e9bd89a (i2c:
attach/detach I2C client device to the ACPI power domain) as the
affected systems could suspend and resume successfully before that
commit.
Fixes: a76e9bd89a (i2c: attach/detach I2C client device to the ACPI power domain)
Reported-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
g762_remove() needs to first call hwmon_device_unregister() and then
g762_of_clock_disable(). For that reason, it is not possible to
convert it to devm_hwmon_device_register_with_groups() and the
the non device managed version must be used.
This is correctly stated in commit message for 398e16db62 ("hwmon:
(g762) Convert to hwmon_device_register_with_groups") but the
associated changes do in fact introduce a call to the device managed
version of the function.
This patch fixes that typo by switching to the non devm_ version.
Fixes: 398e16db62 ("hwmon: (g762) Convert to hwmon_device_register_with_groups")
Cc: stable@vger.kernel.org (3.17+)
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cxgb4i was returning wrong error and not releasing module reference if remote
end abruptly closed TCP connection. This prevents the cxgb4 network module from
being unloaded, further affecting other network drivers dependent on cxgb4
Sending to net as this affects all cxgb4 based network drivers.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pim6_protocol was added when initiation, but it not deleted.
Similarly, unregister RTNL_FAMILY_IP6MR rtnetlink.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:
pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
...
pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
pci 0000:00:02.2: PCI bridge to [bus 03-04]
pci 0000:00:02.2: bridge window [io 0x1000-0x1fff]
pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff]
pci 0000:00:02.2: can't handle 64-bit address space for bridge
In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address. But
this is a bus address, so we should use dma_addr_t instead.
Use dma_addr_t to hold the bridge window base and limit.
The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.
[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes: d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The currect code for nfsd41_cb_get_slot() and nfsd4_cb_done() has no
locking in order to guarantee atomicity, and so allows for races of
the form.
Task 1 Task 2
====== ======
if (test_and_set_bit(0) != 0) {
clear_bit(0)
rpc_wake_up_next(queue)
rpc_sleep_on(queue)
return false;
}
This patch breaks the race condition by adding a retest of the bit
after the call to rpc_sleep_on().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Johannes Berg <johannes@sipsolutions.net> says:
"Here's another last minute fix, for minstrel HT crashing
depending on the value of some uninitialised stack."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marc Kleine-Budde says:
====================
pull-request: can 2014-11-18
this is a pull request of 17 patches for net/master for the v3.18 release
cycle.
The last patch of this pull request ("can: m_can: update to support CAN FD
features") adds, as the description says, a new feature to the m_can driver. As
the m_can driver has been added in v3.18 there is no risk of causing a
regression. Give me a note if this is not okay and I'll create a new pull
request without it.
There is a patch for the CAN infrastructure by Thomas Körper which fixes
calling kfree_skb() from interrupt context. Roman Fietze fixes a typo also in
the infrastructure. A patch by Dong Aisheng adds a generic helper function to
tell if a skb is normal CAN or CAN-FD frame. Alexey Khoroshilov of the Linux
Driver Verification project fixes a memory leak in the esd_usb2 driver. Two
patches by Sudip Mukherjee remove unused variables and fixe the signess of a
variable. Three patches by me add the missing .ndo_change_mtu callback to the
xilinx_can, rcar_can and gs_usb driver.
The remaining patches improve the m_can driver: David Cohen adds the missing
CONFIG_HAS_IOMEM dependency. Dong Aisheng provides 6 bugfix patches (most
important: missing RAM init, sleep in NAPI poll, dlc in RTR). While the last of
his patches adds CAN FD support to the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is currently missing, which results in a crash when one attempts
to set VXLAN tunnel over the mlx4_en when acting as PF.
[ 2408.785472] BUG: unable to handle kernel NULL pointer dereference at (null)
[...]
[ 2408.994104] Call Trace:
[ 2408.996584] [<ffffffffa021f7f5>] ? vxlan_get_rx_port+0xd6/0x103 [vxlan]
[ 2409.003316] [<ffffffffa021f71f>] ? vxlan_lowerdev_event+0xf2/0xf2 [vxlan]
[ 2409.010225] [<ffffffffa0630358>] mlx4_en_start_port+0x862/0x96a [mlx4_en]
[ 2409.017132] [<ffffffffa063070f>] mlx4_en_open+0x17f/0x1b8 [mlx4_en]
While here, make sure to invoke vxlan_get_rx_port() only when VXLAN
offloads are actually enabled and not when they are only supported.
Reported-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6fde8f037e ("bonding: fix locking in
bond_loadbalance_arp_mon()") we can have a stale bond carrier state and
stale curr_active_slave when using arp monitoring in loadbalance modes. The
reason is that in bond_loadbalance_arp_mon() we can't have
do_failover == true but slave_state_changed == false, whenever do_failover
is true then slave_state_changed is also true. Then the following piece
from bond_loadbalance_arp_mon():
if (slave_state_changed) {
bond_slave_state_change(bond);
if (BOND_MODE(bond) == BOND_MODE_XOR)
bond_update_slave_arr(bond, NULL);
} else if (do_failover) {
block_netpoll_tx();
bond_select_active_slave(bond);
unblock_netpoll_tx();
}
will execute only the first branch, always and regardless of do_failover.
Since these two events aren't related in such way, we need to decouple and
consider them separately.
For example this issue could lead to the following result:
Bonding Mode: load balancing (round-robin)
*MII Status: down*
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 100
ARP IP target/s (n.n.n.n form): 192.168.9.2
Slave Interface: ens12
*MII Status: up*
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: 00:0f:53:01:42:2c
Slave queue ID: 0
Slave Interface: eth1
*MII Status: up*
Speed: Unknown
Duplex: Unknown
Link Failure Count: 70
Permanent HW addr: 52:54:00:2f:0f:8e
Slave queue ID: 0
Since some interfaces are up, then the status of the bond should also be
up, but it will never change unless something invokes bond_set_carrier()
(i.e. enslave, bond_select_active_slave etc). Now, if I force the
calling of bond_select_active_slave via for example changing
primary_reselect (it can change in any mode), then the MII status goes to
"up" because it calls bond_select_active_slave() which should've been done
from bond_loadbalance_arp_mon() itself.
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
Fixes: 6fde8f037e ("bonding: fix locking in bond_loadbalance_arp_mon()")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fair reader/writer locks mean that btrfs_clear_path_blocking needs
to strictly follow lock ordering rules even when we already have
blocking locks on a given path.
Before we can clear a blocking lock on the path, we need to make sure
all of the locks have been converted to blocking. This will remove lock
inversions against anyone spinning in write_lock() against the buffers
we're trying to get read locks on. These inversions didn't exist before
the fair read/writer locks, but now we need to be more careful.
We papered over this deadlock in the past by changing
btrfs_try_read_lock() to be a true trylock against both the spinlock and
the blocking lock. This was slower, and not sufficient to fix all the
deadlocks. This patch adds a btrfs_tree_read_lock_atomic(), which
basically means get the spinlock but trylock on the blocking lock.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reported-by: Patrick Schmid <schmid@phys.ethz.ch>
cc: stable@vger.kernel.org #v3.15+
With the isofs_hash() function removed, isofs_hash_ms() is the only user
of isofs_hash_common(), but it's defined inside of an #ifdef, which triggers
this gcc warning in ARM axm55xx_defconfig starting with v3.18-rc3:
fs/isofs/inode.c:177:1: warning: 'isofs_hash_common' defined but not used [-Wunused-function]
This patch moves the function inside of the same #ifdef section to avoid that
warning, which seems the best compromise of a relatively harmless patch for
a late -rc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b0afd8e5db ("isofs: don't bother with ->d_op for normal case")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In "d_prune_alias(): just lock the parent and call __dentry_kill()" the old
dget + d_drop + dput has been replaced with lock_parent + __dentry_kill;
unfortunately, dput() does more than just killing dentry - it also drops the
reference to parent. New variant leaks that reference and needs dput(parent)
after killing the child off.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The removal path for selftest data has an off by one error that causes
the code to dereference beyond the end of the nodes[] array on the first
pass through. The old code only worked by chance on a lot of platforms,
but the bug was recently exposed on aarch64.
The fix is simple. Decrement the node count before dereferencing, not
after.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
This patch fixes a long standing issue introduced during the 3.16 merge window.
Shortly after the merge, exynos5250-based arndale boards began to produce the
following errors:
kern.err kernel: exynos-cpufreq exynos-cpufreq: failed to set cpu voltage
kern.err kernel: cpufreq: __target_index: Failed to change cpu frequency: -22
Further analysis revealed that the S5M8767 voltage regulator used on the
exynos5250-based arndale board utilizes the S3C2410 I2C controller. If the
S3C2410 I2C controller driver is not enabled, the S5M8767 voltage regulator
fails to probe. Therefore a dependency exists between these two drivers.
In the exynos_defconfig both CONFIG_REGULATOR_S5M8767 and CONFIG_I2C_S3C2410
options are enabled, and no errors are produced. However, in the
multi_v7_defconfig only the CONFIG_REGULATOR_S5M8767 option is enabled and the
errors are present. So let's enable the CONFIG_I2C_S3C2410 option in the
multi_v7_defconfig to allow the S5M8767 voltage regulator to probe.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Implement the microMIPS encoding of the J instruction for the purpose of
the static keys feature, fixing a crash early on in bootstrap as the
kernel is unhappy seeing the ISA bit set in jump table entries. Make
sure the ISA bit correctly reflects the instruction encoding chosen for
the kernel, 0 for the standard MIPS and 1 for the microMIPS encoding.
Also make sure the instruction to patch is a 32-bit NOP in the microMIPS
mode as by default the 16-bit short encoding is assumed
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8516/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct the check for the span of the 256MB segment addressable by the J
instruction according to this instruction's semantics. The calculation
of the jump target is applied to the address of the delay-slot
instruction that immediately follows. Adjust the check accordingly by
adding 4 to `e->code' that holds the address of the J instruction
itself.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8515/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit cf62a8b813 ("MIPS: lib: memcpy: Use macro to build the
copy_user code") switched to a macro in order to build the memcpy
symbols in preparation for the EVA support. However, this commit
also removed the NOP instruction after the 'jr ra' when returning
back to the caller. This had no visible side-effects since the next
instruction was a load to the t0 register which was already in the
clobbered list, but it may have undesired effects in the future
if some other code is introduced in between the .Ldone and
the .Ll_exc_copy labels.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8512/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HTW needs to stop and start again whenever the EntryHI register
changes otherwise an inflight HTW operation might use the new
EntryHI register for updating an old entry and that could lead
to crashes or even a machine check exception. We fix this by
ensuring the HTW has stop whenever the EntryHI register is about
to change
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8511/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When EVA is turned on and prefetching is being used in memcpy.S,
the v1 register is being used as a helper register to the PREFE
instruction. However, v1 ($3) was not in the clobber list, which
means that the compiler did not preserve it across function calls,
and that could corrupt the value of the register leading to all
sorts of userland crashes. We fix this problem by using the
DADDI_SCRATCH macro to define the clobbered register when
CONFIG_EVA && CONFIG_CPU_HAS_PREFETCH are enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8510/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
export the __node_distances symbol in the ip27 memory code to fix the
build error:
Building modules, stage 2.
MODPOST 311 modules
ERROR: "__node_distances" [drivers/block/nvme.ko] undefined!
scripts/Makefile.modpost:90: recipe for target '__modpost' failed
when building the kernel with:
CONFIG_SGI_IP27=y
CONFIG_BLK_DEV_NVME=m
Signed-off-by: James Cowgill <James.Cowgill@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Even when security labels are disabled we support at least the same
attributes as v4.1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull "ARM: tegra: Device tree fixes for v3.18-rc5" from Thierry Reding:
This contains the serial port numbering fixes that are required for the
serial port numbering to stay the same with or without the serial core
making use of the aliases defined in DT.
eMMC is also fixed for TN7 and Roth boards which were using the wrong
regulators.
* tag 'tegra-for-3.18-fixes-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: roth: Fix SD card VDD_IO regulator
ARM: tegra: Remove eMMC vmmc property for roth/tn7
ARM: dts: tegra: move serial aliases to per-board
ARM: tegra: Add serial port labels to Tegra124 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Renesas ARM Based SoC DT Fixes for v3.18" from Simon Horman:
* Correct IIC0 parent clock on r8a7740
* Correct SD3CKCR address to device tree on r8a7790
* tag 'renesas-dt-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 dtsi: Correct IIC0 parent clock
ARM: shmobile: r8a7790: Fix SD3CKCR address to device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Renesas ARM Based SoC Fixes for v3.18" from Simon Horman:
* Set i2c clks_per_count to 2 on kzm9g
* tag 'renesas-soc-fixes-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g legacy: Set i2c clks_per_count to 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes: 6b8f1ca558 ("USB: ssu100: set tty_flags in ssu100_process_packet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reporting of overrun errors, which are not associated with a
character. Instead insert a null character and report only once.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Merge "Allwinner fixes for 3.18" from Maxime Ripard:
A fix for the A31 dma controller that requires the AHB clock to be parented to
PLL6 in order to operate.
* tag 'sunxi-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The interrupts were activated and the handler registered before the clockevent
was registered in the probe function.
The interrupt handler, however, was making the assumption that the clockevent
device was registered.
That could cause a null pointer dereference if the timer interrupt was firing
during this narrow window.
Fix that by moving the clockevent registration before the interrupt is enabled.
Reported-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Explicitly set the dr_mode for the dwc3 controller on the
Snow board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is
build with USB gadget support.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The commit 5935839ad7
"mac80211: improve minstrel_ht rate sorting by throughput & probability"
introduced a crash on rate sorting that occurs when the rate added to
the sorting array is faster than all the previous rates. Due to an
off-by-one error, it reads the rate index from tp_list[-1], which
contains uninitialized stack garbage, and then uses the resulting index
for accessing the group rate stats, leading to a crash if the garbage
value is big enough.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A misspelled 'arbitrary' propagated to quite a few locations in the DT
binding documentation for pin-controllers. Fixing by:
git grep abitrary | cut -f1 -d: | xargs sed -i 's/abitrary/arbitrary/'
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch is used to add vendor prefix for Micron Technology, Inc. in
the vendor-prefixes.txt file.
Micron Technology, Inc. is an American multinational corporation based
in Boise, Idaho, best known for producing many forms of semiconductor
devices. This includes DRAM, SDRAM, flash memory, eMMC and SSDs.
Signed-off-by: Bean Huo <bpqw@micron.com>
[robh: cleanup commit msg formatting and company name]
Signed-off-by: Rob Herring <robh@kernel.org>
Chips&Media is a developer of Video Codec IP cores.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[robh: fix-up alphabetical ordering]
Signed-off-by: Rob Herring <robh@kernel.org>
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
__earlycon_of_table_sentinel.compatible is a char[128], not a pointer, so
it will never be NULL. Checking it against NULL causes the match loop to
run past the end of the array, and eventually match a bogus entry, under
the following conditions:
- Kernel command line specifies "earlycon" with no parameters
- DT has a stdout-path pointing to a UART node
- The UART driver doesn't use OF_EARLYCON_DECLARE (or maybe the console
driver is compiled out)
Fix this by checking to see if match->compatible is a non-empty string.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rob Herring <robh@kernel.org>
a9ecdc0fdc ("of/irq: Fix lookup to use 'interrupts-extended' property
first") updated the description to say that:
- Both 'interrupts' and 'interrupts-extended' may be present
- Software should prefer 'interrupts-extended'
- Software that doesn't comprehend 'interrupts-extended' may use
'interrupts'
But there is still a paragraph at the end that prohibits having both and
says 'interrupts' should be preferred.
Remove the contradictory text.
Fixes: a9ecdc0fdc ("of/irq: Fix lookup to use 'interrupts-extended' property first")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.13+
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When setting up permissions on kernel memory at boot, the end of the
PMD that was split from bss remained executable. It should be NX like
the rest. This performs a PMD alignment instead of a PAGE alignment to
get the correct span of memory.
Before:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82c00000 10M RW PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82df5000 2004K RW GLB NX pte
0xffffffff82df5000-0xffffffff82e00000 44K RW GLB x pte
0xffffffff82e00000-0xffffffffc0000000 978M pmd
After:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82e00000 12M RW PSE GLB NX pmd
0xffffffff82e00000-0xffffffffc0000000 978M pmd
[ tglx: Changed it to roundup(_brk_end, PMD_SIZE) and added a comment.
We really should unmap the reminder along with the holes
caused by init,initdata etc. but thats a different issue ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141114194737.GA3091@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add sandisk to the list of vendors. This prefix should be used
also for companies absorbed by Sandisk, like M-Systems.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Rob Herring <robh@kernel.org>
The variable err was of the type u32. It was being compared with < 0, and being
an unsigned variable the comparison would have been always false.
Moreover, err was getting the return value from set_reset_mode() and
xcan_set_bittiming(), and both are returning int.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit 8c328a262f ("spi: sirf: Avoid duplicate code in various
bits_per_word cases") is wrong in setting data width register of
fifo is not right, it should use sspi->word_width >> 1 to set
related bits. According to hardware spec, the mapping between
register value and data width:
0 - byte
1 - WORD
2 - DWORD
Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN device drivers can use can_is_canfd_skb() to check if the frame to send
is on CAN FD mode or normal CAN mode.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in CAN's dev.c:
CIA -> CiA
which stands for CAN in Automation.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The microphone mute led on the Latitude E5550 can't work. We need to
apply DELL_WMI_MIC_MUTE_LED quirk to this machine.
The machine uses alc293 codec and already applied the quirk
ALC293_FIXUP_DELL1_MIC_NO_PRESENCE through pin_fixup_tbl[].
Here we just let DELL_WMI_MIC_MUTE_LED be chained to
ALC269_FIXUP_HEADSET_MODE, then the machine will have these
quirks ALC293_FIXUP_DELL1_MIC_NO_PRESENCE-->
ALC269_FIXUP_HEADSET_MODE-->ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED.
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have one more Dell machine needs DELL_WMI_MIC_MUTE_LED quirk, but
the machine uses alc293 instead of alc255. So if
DELL_WMI_MIC_MUTE_LED still chain ALC255_FIXUP_DELL1_MIC_NO_PRESENCE,
the machine can't use this quirk.
To change this situation, let the DELL_WMI_MIC_MUTE_LED to be a
standalone quirk, and let other quirks chain it.
After this change, this quirk can be chained to any existing quirks,
and as a result, it is possible that this quirk is applied to
a non-Dell machine or a Dell machine without mic mute led on it, but
it is still safe since alc_fixup_dell_wmi() will return an error in
these situations.
And remove the quirk for machine with subsystem id 0x6010 and 0x601f,
these two machines will fall back to the quirk
ALC255_FIXUP_DELL1_MIC_NO_PRESENCE-->ALC255_FIXUP_HEADSET_MODE-->
ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED through pin_fixup_tbl[].
BugLink: https://bugs.launchpad.net/bugs/1381856
Reported-and-tested-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 543c043cba ("powerpc/fsl_msi: change the irq handler from
chained to normal") changes the msi cascade handler from chained to
normal. Since cascade handler must run in hard interrupt context, this
will cause kernel panic if we force threading of all the interrupt
handler via kernel command parameter 'threadirqs'. So mark the irq
handler IRQF_NO_THREAD explicitly.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
ASoC: Fixes for v3.18
As well as the usual driver fixes there's a few other things here:
One is a fix for a race in DPCM which is unfortuantely a rather large
diffstat, this is the result of growing usage of the mainline code and
hence more detailed testing so I'm relatively happy.
The other is a fix for non-DT machine driver matching following some of
the componentization work which is much more focused.
Both have had a while to cook in -next.
Return value of irq_of_parse_and_map() is unsigned int, with 0
indicating failure, so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Cc: stable@vger.kernel.org # v3.17
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kill the submitted URB in brcmf_usb_dl_cmd if the request timed out. This
assures the URB is never submitted twice. It also prevents a possible
use-after-free of the URB transfer buffer if a timeout occurs.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit that went into 3.17:
ath9k: Summarize hw state per channel context
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
broke multi-vif configuration due to not properly calculating
the bssid mask.
The test case that caught this was:
create wlan0 and sta0-4 (6 total), not sure how much that matters.
associate all 6 (works fine)
disconnect 5 of them, leaving sta0 up
Start trying to bring up the other 5 one at a time. It will
fail, with iw events looking like this (in these logs, several
sta are trying to come up, but symptom is the same with just one)
The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.
Re-adding those calls fixes my test case. Fix bad comment
as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial fix to check the A bit of CCCR for memory frequency
calculations, where the shift of the bit index was missing, triggering a
wrong calculation of memory frequency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 79c6ab5095 (clk: divider: add CLK_DIVIDER_READ_ONLY flag) in
v3.16 introduced the CLK_DIVIDER_READ_ONLY flag which caused the
recalc_rate() and round_rate() clock callbacks to be omitted.
However using this flag has the unfortunate side effect of causing the
clock recalculation code when a clock rate change is attempted to always
treat it as a pass-through clock, i.e. with a fixed divide of 1, which
may not be the case. Child clock rates are then recalculated using the
wrong parent rate.
Therefore instead of dropping the recalc_rate() and round_rate()
callbacks, alter clk_divider_bestdiv() to always report the current
divider as the best divider so that it is never altered.
For me the read only clock was the system clock, which divided the PLL
rate by 2, from which both the UART and the SPI clocks were divided.
Initial setting of the UART rate set it correctly, but when the SPI
clock was set, the other child clocks were miscalculated. The UART clock
was recalculated using the PLL rate as the parent rate, resulting in a
UART new_rate of double what it should be, and a UART which spewed forth
garbage when the rate changes were propagated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Max Schwarz <max.schwarz@online.de>
Cc: <stable@vger.kernel.org> # v3.16+
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
There is a duplication in a clock name for apq8084 platform that causes
the following warning: "RBCPR_CLK_SRC" redefined
Resolve this by adding a MMSS_ prefix to this clock and making its name
coherent with msm8974 platform.
Fixes: 2b46cd23a5 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
at91rm9200_clk_usb_set_rate might fail depending on the requested rate,
because the parent_rate / rate remainder is not necessarily zero.
Moreover, when rounding down the calculated rate we might alter the
divisor calculation and end up with an invalid divisor.
To solve those problems, accept a non zero remainder, and always round
division to the closest result.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Specified in section 5.2.5.6.1 of the USB Audio Class 2.0 definition.
Solves the following error for C-Media 6632A (Asus Xonar U7):
[ 8219.676164] cannot get ctl value: req = 0x81, wValue = 0x0, wIndex = 0x1400, type = 3
Signed-off-by: Johan Rastén <johan@oljud.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ebtables on the OUTPUT chain (NF_BR_LOCAL_OUT) would not work as expected
for both locally generated IGMP and MLD queries. The IP header specific
filter options are off by 14 Bytes for netfilter (actual output on
interfaces is fine).
NF_HOOK() expects the skb->data to point to the IP header, not the
ethernet one (while dev_queue_xmit() does not). Luckily there is an
br_dev_queue_push_xmit() helper function already - let's just use that.
Introduced by eb1d164143
("bridge: Add core IGMP snooping support")
Ebtables example:
$ ebtables -I OUTPUT -p IPv6 -o eth1 --logical-out br0 \
--log --log-level 6 --log-ip6 --log-prefix="~EBT: " -j DROP
before (broken):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=64a4:39c2:86dd:6000:0000:0020:0001:fe80 IPv6 \
DST=0000:0000:0000:0004:64ff:fea4:39c2:ff02, \
IPv6 priority=0x3, Next Header=2
after (working):
~EBT: IN= OUT=eth1 MAC source = 02:04:64:a4:39:c2 \
MAC dest = 33:33:00:00:00:01 proto = 0x86dd IPv6 \
SRC=fe80:0000:0000:0000:0004:64ff:fea4:39c2 IPv6 \
DST=ff02:0000:0000:0000:0000:0000:0000:0001, \
IPv6 priority=0x0, Next Header=0
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make sure the netlink group exists, otherwise you can trigger an out
of bound array memory access from the netlink_bind() path. This splat
can only be triggered only by superuser.
[ 180.203600] UBSan: Undefined behaviour in ../net/netfilter/nfnetlink.c:467:28
[ 180.204249] index 9 is out of range for type 'int [9]'
[ 180.204697] CPU: 0 PID: 1771 Comm: trinity-main Not tainted 3.18.0-rc4-mm1+ #122
[ 180.205365] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org
+04/01/2014
[ 180.206498] 0000000000000018 0000000000000000 0000000000000009 ffff88007bdf7da8
[ 180.207220] ffffffff82b0ef5f 0000000000000092 ffffffff845ae2e0 ffff88007bdf7db8
[ 180.207887] ffffffff8199e489 ffff88007bdf7e18 ffffffff8199ea22 0000003900000000
[ 180.208639] Call Trace:
[ 180.208857] dump_stack (lib/dump_stack.c:52)
[ 180.209370] ubsan_epilogue (lib/ubsan.c:174)
[ 180.209849] __ubsan_handle_out_of_bounds (lib/ubsan.c:400)
[ 180.210512] nfnetlink_bind (net/netfilter/nfnetlink.c:467)
[ 180.210986] netlink_bind (net/netlink/af_netlink.c:1483)
[ 180.211495] SYSC_bind (net/socket.c:1541)
Moreover, define the missing nf_tables and nf_acct multicast groups too.
Reported-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The datasheet for PL330 says that the data buffer value in the CRD
register is 10bits wide. However, the value stored is "minus one",
which the driver corrects for. Maximum value that the data buffer
depth can have is 1024 lines, which requires 11 bits for storage.
While making updates I found printing the peripheral ID as a hex
value to be more useful as the datasheet shows the values that way.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MFIFO is shared by all channels so restrict each memcpy to it's fair
share. This is being over cautious, but without a global view of DMA
channel usage on a system it's not possible to come up with a more
optimum safe limit.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The algorithm used for programming the DMA Controller doesn't take into
consideration the requirements of transfers that are not aligned to the
bus width. This failure may result in DMA transferring one too few MFIFO
entries (so too few bytes are copied) or the DMA trying to write one too
many MFIFO entries and hanging because this is never provided.
See "MFIFO Usage Overview" chapter in the the TRM for "CoreLink DMA
Controller DMA-330", Revision r1p1.
We work around these shortcomings by making sure we pick a burst size
and length which ensures no bursts straddle an MFIFO entry.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
[squashed linker error "undefined reference to `__aeabi_uldivmod]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.
touchpad-edge-detector output:
> Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
> Move one finger around the touchpad to detect the actual edges
> Kernel says: x [1472..5674], y [1408..4684]
> Touchpad sends: x [1264..5675], y [1171..4688]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Cc: stable@vger.kernel.org
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull ARM SoC fixes from Olof Johansson:
"Another small set of fixes:
- some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- a handful of smaller fixes for OMAP
- a couple of added file patterns for OMAP entries in MAINTAINERS"
* tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: at91/dt: Fix sama5d3x typos
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
Pull sparc fixes from David Miller:
1) Fix NULL oops in Schizo PCI controller error handler.
2) Fix race between xchg and other operations on 32-bit sparc, from
Andreas Larsson.
3) swab*() helpers need a dummy memory input operand to show data flow
on 64-bit sparc.
4) Fix RCU warnings due to missing irq_{enter,exit}() around
generic_smp_call_function*() calls.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix constraints on swab helpers.
sparc32: Implement xchg and atomic_xchg using ATOMIC_HASH locks
sparc64: Do irq_{enter,exit}() around generic_smp_call_function*().
sparc64: Fix crashes in schizo_pcierr_intr_other().
Pull md bugfix from Neil Brown:
"One fix for md for 3.18.
This fixes a regression introduced in 3.13"
* tag 'md/3.18-fix' of git://neil.brown.name/md:
md: Always set RECOVERY_NEEDED when clearing RECOVERY_FROZEN
Some DT files had a typo with a missing "5" in sama5d3x first compatible string.
Signed-off-by: Peter Rosin <peda@axentia.se>
[nicolas.ferre@atmel.com: modify commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap fixes against v3.18-rc4" from Tony Lindgren:
Few omap fixes for hangs and wrong pinctrl defines, and update
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
* tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "mvebu fixes for v3.18" from Jason Cooper:
- Armada XP
- Generalize i2c quirk
- orion
- Fix irq storm caused by specific sequence of request_irq
* tag 'mvebu-fixes-3.18' of git://git.infradead.org/linux-mvebu:
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
md_check_recovery will skip any recovery and also clear
MD_RECOVERY_NEEDED if MD_RECOVERY_FROZEN is set.
So when we clear _FROZEN, we must set _NEEDED and ensure that
md_check_recovery gets run.
Otherwise we could miss out on something that is needed.
In particular, this can make it impossible to remove a
failed device from an array is the 'recovery-needed' processing
didn't happen.
Suitable for stable kernels since 3.13.
Cc: stable@vger.kernel.org (3.13+)
Reported-and-tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Fixes: 30b8feb730
Signed-off-by: NeilBrown <neilb@suse.de>
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20
head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0
dev:port1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:100!
invalid opcode: 0000 [#1] SMP
Modules linked in: ixgbe(O)
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4
[...]
Call Trace:
<IRQ>
[<ffffffff80578226>] ? skb_put+0x3a/0x3b
[<ffffffff80612a5d>] ? add_grhead+0x45/0x8e
[<ffffffff80612e3a>] ? add_grec+0x394/0x3d4
[<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d
[<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45
[<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68
[<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182
[<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d
[<ffffffff8025112b>] ? irq_exit+0x4e/0xd3
[<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46
[<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6ead
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com>
Fixes: 72e09ad107 ("ipv6: avoid high order allocations")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are reading the memory location, so we have to have a memory
constraint in there purely for the sake of showing the data flow
to the compiler.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the threshold to low by default. With this thresholds any movement
on the device with this sensor will generate event.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change the mode to push/pull type instead of open drain as some
platforms fails to drive the GPIO pin with open drain.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pravin B Shelar says:
====================
Open vSwitch
Following fixes are accumulated in ovs-repo.
Three of them are related to protocol processing, one is
related to memory leak in case of error and one is to
fix race.
Patch "Validate IPv6 flow key and mask values" has conflicts
with net-next, Let me know if you want me to send the patch
for net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Solves possible lockup issues that can be seen from firmware DCB agents calling
into the DCB app api.
DCB firmware event queues can be tied in with NAPI so that dcb events are
generated in softIRQ context. This can results in calls to dcb_*app()
functions which try to take the dcb_lock.
If the the event triggers while we also have the dcb_lock because lldpad or
some other agent happened to be issuing a get/set command we could see a cpu
lockup.
This code was not originally written with firmware agents in mind, hence
grabbing dcb_lock from softIRQ context was not considered.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of any failure ieee802154fake_probe() just calls unregister_netdev().
But it does not look safe to unregister netdevice before it was registered.
The patch implements straightforward resource deallocation in case of
failure in ieee802154fake_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI fixes from James Bottomley:
"This is a set of six fixes and a MAINTAINER update.
The fixes are two multipath (one in Test Unit Ready handling for the
path checkers and one in the section of code that sends a start unit
after failover; both of these were perturbed by the scsi-mq update), a
CD-ROM door locking fix that was likewise introduced by scsi-mq and
three driver fixes for a previous code update in cxgb4i, megaraid_sas
and bnx2fc"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
bnx2fc: fix tgt spinlock locking
megaraid_sas: fix bug in handling return value of pci_enable_msix_range()
cxgb4i: send abort_rpl correctly
cxgbi: add maintainer for cxgb3i/cxgb4i
scsi: TUR path is down after adapter gets reset with multipath
scsi: call device handler for failed TUR command
scsi: only re-lock door after EH on devices that were reset
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter updates for your net tree,
they are:
1) Fix missing initialization of the range structure (allocated in the
stack) in nft_masq_{ipv4, ipv6}_eval, from Daniel Borkmann.
2) Make sure the data we receive from userspace contains the req_version
structure, otherwise return an error incomplete on truncated input.
From Dan Carpenter.
3) Fix handling og skb->sk which may cause incorrect handling
of connections from a local process. Via Simon Horman, patch from
Calvin Owens.
4) Fix wrong netns in nft_compat when setting target and match params
structure.
5) Relax chain type validation in nft_compat that was recently included,
this broke the matches that need to be run from the route chain type.
Now iptables-test.py automated regression tests report success again
and we avoid the only possible problematic case, which is the use of
nat targets out of nat chain type.
6) Use match->table to validate the tablename, instead of the match->name.
Again patch for nft_compat.
7) Restore the synchronous release of objects from the commit and abort
path in nf_tables. This is causing two major problems: splats when using
nft_compat, given that matches and targets may sleep and call_rcu is
invoked from softirq context. Moreover Patrick reported possible event
notification reordering when rules refer to anonymous sets.
8) Fix race condition in between packets that are being confirmed by
conntrack and the ctnetlink flush operation. This happens since the
removal of the central spinlock. Thanks to Jesper D. Brouer to looking
into this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Ingo Molnar:
"Microcode fixes, a Xen fix and a KASLR boot loading fix with certain
memory layouts"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Fix ucode patch stashing on 32-bit
x86/core, x86/xen/smp: Use 'die_complete' completion when taking CPU down
x86, microcode: Fix accessing dis_ucode_ldr on 32-bit
x86, kaslr: Prevent .bss from overlaping initrd
x86, microcode, AMD: Fix early ucode loading on 32-bit
Trying to add an unreachable route incorrectly returns -ESRCH if
if custom FIB rules are present:
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: Network is unreachable
[root@localhost ~]# ip rule add to 55.66.77.88 table 200
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: No such process
[root@localhost ~]#
Commit 83886b6b63 ("[NET]: Change "not found"
return value for rule lookup") changed fib_rules_lookup()
to use -ESRCH as a "not found" code internally, but for user space it
should be translated into -ENETUNREACH. Handle the translation centrally in
ipv4-specific fib_lookup(), leaving the DECnet case alone.
On a related note, commit b7a71b51ee
("ipv4: removed redundant conditional") removed a similar translation from
ip_route_input_slow() prematurely AIUI.
Fixes: b7a71b51ee ("ipv4: removed redundant conditional")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that the x86-64 csum_partial_copy_from_user() is
somewhat confused about what it should do on errors, notably it mostly
clears the uncopied end result buffer, but misses that for the initial
alignment case.
All users should check for errors, so it's dubious whether the clearing
is even necessary, and Al also points out that we should probably clean
up the calling conventions, but regardless of any future changes to this
function, the fact that it is inconsistent is just annoying.
So make the __get_user() failure path use the same error exit as all the
other errors do.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have some very similarly named command-line options:
arch/x86/kernel/cpu/common.c:__setup("noxsave", x86_xsave_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaveopt", x86_xsaveopt_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaves", x86_xsaves_setup);
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit d670ec1317 "posix-cpu-timers: Cure SMP wobbles" fixes one glibc
test case in cost of breaking another one. After that commit, calling
clock_nanosleep(TIMER_ABSTIME, X) and then clock_gettime(&Y) can result
of Y time being smaller than X time.
Reproducer/tester can be found further below, it can be compiled and ran by:
gcc -o tst-cpuclock2 tst-cpuclock2.c -pthread
while ./tst-cpuclock2 ; do : ; done
This reproducer, when running on a buggy kernel, will complain
about "clock_gettime difference too small".
Issue happens because on start in thread_group_cputimer() we initialize
sum_exec_runtime of cputimer with threads runtime not yet accounted and
then add the threads runtime to running cputimer again on scheduler
tick, making it's sum_exec_runtime bigger than actual threads runtime.
KOSAKI Motohiro posted a fix for this problem, but that patch was never
applied: https://lkml.org/lkml/2013/5/26/191 .
This patch takes different approach to cure the problem. It calls
update_curr() when cputimer starts, that assure we will have updated
stats of running threads and on the next schedule tick we will account
only the runtime that elapsed from cputimer start. That also assure we
have consistent state between cpu times of individual threads and cpu
time of the process consisted by those threads.
Full reproducer (tst-cpuclock2.c):
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <stdio.h>
#include <time.h>
#include <pthread.h>
#include <stdint.h>
#include <inttypes.h>
/* Parameters for the Linux kernel ABI for CPU clocks. */
#define CPUCLOCK_SCHED 2
#define MAKE_PROCESS_CPUCLOCK(pid, clock) \
((~(clockid_t) (pid) << 3) | (clockid_t) (clock))
static pthread_barrier_t barrier;
/* Help advance the clock. */
static void *chew_cpu(void *arg)
{
pthread_barrier_wait(&barrier);
while (1) ;
return NULL;
}
/* Don't use the glibc wrapper. */
static int do_nanosleep(int flags, const struct timespec *req)
{
clockid_t clock_id = MAKE_PROCESS_CPUCLOCK(0, CPUCLOCK_SCHED);
return syscall(SYS_clock_nanosleep, clock_id, flags, req, NULL);
}
static int64_t tsdiff(const struct timespec *before, const struct timespec *after)
{
int64_t before_i = before->tv_sec * 1000000000ULL + before->tv_nsec;
int64_t after_i = after->tv_sec * 1000000000ULL + after->tv_nsec;
return after_i - before_i;
}
int main(void)
{
int result = 0;
pthread_t th;
pthread_barrier_init(&barrier, NULL, 2);
if (pthread_create(&th, NULL, chew_cpu, NULL) != 0) {
perror("pthread_create");
return 1;
}
pthread_barrier_wait(&barrier);
/* The test. */
struct timespec before, after, sleeptimeabs;
int64_t sleepdiff, diffabs;
const struct timespec sleeptime = {.tv_sec = 0,.tv_nsec = 100000000 };
/* The relative nanosleep. Not sure why this is needed, but its presence
seems to make it easier to reproduce the problem. */
if (do_nanosleep(0, &sleeptime) != 0) {
perror("clock_nanosleep");
return 1;
}
/* Get the current time. */
if (clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &before) < 0) {
perror("clock_gettime[2]");
return 1;
}
/* Compute the absolute sleep time based on the current time. */
uint64_t nsec = before.tv_nsec + sleeptime.tv_nsec;
sleeptimeabs.tv_sec = before.tv_sec + nsec / 1000000000;
sleeptimeabs.tv_nsec = nsec % 1000000000;
/* Sleep for the computed time. */
if (do_nanosleep(TIMER_ABSTIME, &sleeptimeabs) != 0) {
perror("absolute clock_nanosleep");
return 1;
}
/* Get the time after the sleep. */
if (clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &after) < 0) {
perror("clock_gettime[3]");
return 1;
}
/* The time after sleep should always be equal to or after the absolute sleep
time passed to clock_nanosleep. */
sleepdiff = tsdiff(&sleeptimeabs, &after);
if (sleepdiff < 0) {
printf("absolute clock_nanosleep woke too early: %" PRId64 "\n", sleepdiff);
result = 1;
printf("Before %llu.%09llu\n", before.tv_sec, before.tv_nsec);
printf("After %llu.%09llu\n", after.tv_sec, after.tv_nsec);
printf("Sleep %llu.%09llu\n", sleeptimeabs.tv_sec, sleeptimeabs.tv_nsec);
}
/* The difference between the timestamps taken before and after the
clock_nanosleep call should be equal to or more than the duration of the
sleep. */
diffabs = tsdiff(&before, &after);
if (diffabs < sleeptime.tv_nsec) {
printf("clock_gettime difference too small: %" PRId64 "\n", diffabs);
result = 1;
}
pthread_cancel(th);
return result;
}
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20141112155843.GA24803@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There were several reports that on some systems writing the SBOX0 PMU
initialization MSR would #GP at boot. This did not happen on all
systems -- my two test systems booted fine.
Writing the three initialization bits bit-by-bit seems to avoid the
problem. So add a special callback to do just that.
This replaces an earlier patch that disabled the SBOX.
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-and-Tested-by: Patrick Lu <patrick.lu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: http://lkml.kernel.org/r/1415062828-19759-4-git-send-email-andi@firstfloor.org
[ Fixed a whitespace error and added attribution tags that were left out inexplicably. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a USB control message delay quirk for a few specific Marantz/Denon
devices. Without the delay the DACs will not work properly and produces the
following type of messages:
Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use
Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use
There are likely other Marantz/Denon devices using the same USB module which exhibit the
same problems. But as this cannot be verified I limited the patch to the devices
I could test.
The following two devices are covered by this path:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a CPU hotplugged out, we call perf_remove_from_context() (via
perf_event_exit_cpu()) to rip each CPU-bound event out of its PMU's cpu
context, but leave siblings grouped together. Freeing of these events is
left to the mercy of the usual refcounting.
When a CPU-bound event's refcount drops to zero we cross-call to
__perf_remove_from_context() to clean it up, detaching grouped siblings.
This works when the relevant CPU is online, but will fail if the CPU is
currently offline, and we won't detach the event from its siblings
before freeing the event, leaving the sibling list corrupt. If the
sibling list is later walked (e.g. because the CPU cam online again
before a remaining sibling's refcount drops to zero), we will walk the
now corrupted siblings list, potentially dereferencing garbage values.
Given that the events should never be scheduled again (as we removed
them from their context), we can simply detatch siblings when the CPU
goes down in the first place. If the CPU comes back online, the
redundant call to __perf_remove_from_context() is safe.
Reported-by: Drew Richardson <drew.richardson@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: vincent.weaver@maine.edu
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1415203904-25308-2-git-send-email-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull ARM fixes from Russell King:
"Two fixes this time, one to ensure that the kuser helper option
depends on MMU as they aren't available for noMMU targets (and if the
option is selected, we end up oopsing.)
The second fix plugs a corner case with the decompressor, ensuring
that the instruction stream can see the relocated code in every case
on ARMv7 CPUs"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8198/1: make kuser helpers depend on MMU
ARM: 8191/1: decompressor: ensure I-side picks up relocated code
Pull parisc updates from Helge Deller:
"Changes include:
- wire up the bpf syscall
- remove CONFIG_64BIT usage from some userspace-exported header files
- use compat functions for msgctl, shmat, shmctl and semtimedop
syscalls"
* 'parisc-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Avoid using CONFIG_64BIT in userspace exported headers
parisc: Use compat layer for msgctl, shmat, shmctl and semtimedop syscalls
parisc: Use BUILD_BUG() instead of undefined functions
parisc: Wire up bpf syscall
Pull power supply updates from Sebastian Reichel:
"Power supply and reset changes for the v3.18-rc:
- misc. charger-manager fixes
- year 2038 fix in ab8500_fg
- fix error handling of bq2415x_charger"
* tag 'for-v3.18-rc' of git://git.infradead.org/battery-2.6:
power: charger-manager: Fix accessing invalidated power supply after charger unbind
power: charger-manager: Fix accessing invalidated power supply after fuel gauge unbind
power: charger-manager: Avoid recursive thermal get_temp call
power_supply: Add no_thermal property to prevent recursive get_temp calls
power: bq2415x_charger: Fix memory leak on DTS parsing error
power: bq2415x_charger: Properly handle ENODEV from power_supply_get_by_phandle
power: ab8500_fg.c: use 64-bit time types
Pull drm gixes from Dave Airlie:
- exynos: infinite loop regressions fixed
- i915: one regression
- radeon: one race condition on monitor probing
- noveau: two regressions
- tegra: one vblank regression fix
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/tegra: dc: Add missing call to drm_vblank_on()
drm/nouveau/nv50/disp: Fix modeset on G94
drm/gk20a/fb: fix setting of large page size bit
drm/radeon: add locking around atombios scratch space usage
drm/i915: Fix obj->map_and_fenceable across tiling changes
drm/exynos: fix possible infinite loop issue
drm/exynos: g2d: fix null pointer dereference
drm/exynos: resolve infinite loop issue on non multi-platform
drm/exynos: resolve infinite loop issue on multi-platform
Sasha Levin reports:
"gcc5 changes the default standard to c11, which makes kernel build
unhappy
Explicitly define the kernel standard to be gnu89 which should keep
everything working exactly like it was before gcc5"
There are multiple small issues with the new default, but the biggest
issue seems to be that the old - and very useful - GNU extension to
allow a cast in front of an initializer has gone away.
Patch updated by Kirill:
"I'm pretty sure all gcc versions you can build kernel with supports
-std=gnu89. cc-option is redunrant.
We also need to adjust HOSTCFLAGS otherwise allmodconfig fails for me"
Note by Andrew Pinski:
"Yes it was reported and both problems relating to this extension has
been added to gnu99 and gnu11. Though there are other issues with the
kernel dealing with extern inline have different semantics between
gnu89 and gnu99/11"
End result: we may be able to move up to a newer stdc model eventually,
but right now the newer models have some annoying deficiencies, so the
traditional "gnu89" model ends up being the preferred one.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Singed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- stable patches to fix NFSv4.x delegation reclaim error paths
- fix a bug whereby we were advertising NFSv4.1 but using NFSv4.2
features
- fix a use-after-free problem with pNFS block layouts
- fix a memory leak in the pNFS files O_DIRECT code
- replace an intrusive and Oops-prone performance fix in the NFSv4
atomic open code with a safer one-line version and revert the two
original patches"
* tag 'nfs-for-3.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
sunrpc: fix sleeping under rcu_read_lock in gss_stringify_acceptor
NFS: Don't try to reclaim delegation open state if recovery failed
NFSv4: Ensure that we call FREE_STATEID when NFSv4.x stateids are revoked
NFSv4: Fix races between nfs_remove_bad_delegation() and delegation return
NFSv4.1: nfs41_clear_delegation_stateid shouldn't trust NFS_DELEGATED_STATE
NFSv4: Ensure that we remove NFSv4.0 delegations when state has expired
NFS: SEEK is an NFS v4.2 feature
nfs: Fix use of uninitialized variable in nfs_getattr()
nfs: Remove bogus assignment
nfs: remove spurious WARN_ON_ONCE in write path
pnfs/blocklayout: serialize GETDEVICEINFO calls
nfs: fix pnfs direct write memory leak
Revert "NFS: nfs4_do_open should add negative results to the dcache."
Revert "NFS: remove BUG possibility in nfs4_open_and_get_state"
NFSv4: Ensure nfs_atomic_open set the dentry verifier on ENOENT
Currently, we get the new GSEL bits by OR-ing the old values
with the new ones. This only works first time when the old
values are 0.
Startup:
* GSEL0 = 0, GSEL1 = 0
Set range to 4G: (GSEL0 = 1, GSEL1 = 0)
* GSEL0 = 0 | 1 = 1
* GSEL1 = 0 | 0 = 0
* correct
Change range to 2G: (GSEL0 = 0, GSEL1 = 0)
* GSEL0 = 1 | 0 = 1
* GSEL1 = 0 | 0 = 0
* wrong, GSEL0 should be 0
This has the nice effect that we can use the full scale range,
exported in in_accel_scale_available.
Fixes: a735e3d7f0 (iio: accel: kxcjk-1013: Set adjustable range)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The direction field is set on 7 bits, thus we need to AND it with 0111 111 mask
in order to retrieve it, that is 0x7F, not 0xCF as it is now.
Fixes: ade7ef7ba (staging:iio: Differential channel handling)
Signed-off-by: Cristina Ciocan <cristina.ciocan@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
dp read operations depends on ovs_dp_cmd_fill_info(). This API
needs to looup vport to find dp name, but vport lookup can
fail. Therefore to keep vport reference alive we need to
take ovs lock.
Introduced by commit 6093ae9aba ("openvswitch: Minimize
dp and vport critical sections").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
match_validate() enforce that a mask matching on NDP attributes has also an
exact match on ICMPv6 type.
The ICMPv6 type, which is 8-bit wide, is stored in the 'tp.src' field of
'struct sw_flow_key', which is 16-bit wide.
Therefore, an exact match on ICMPv6 type should only check the first 8 bits.
This commit fixes a bug that prevented flows with an exact match on NDP field
from being installed
Introduced by commit 03f0d916aa ("openvswitch: Mega flow implementation").
Signed-off-by: Daniele Di Proietto <ddiproietto@vmware.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The checksum of ICMPv6 packets uses the IP pseudoheader as part of
the calculation, unlike ICMP in IPv4. This was not implemented,
which means that modifying the IP addresses of an ICMPv6 packet
would cause the checksum to no longer be correct as the psuedoheader
did not match.
Introduced by commit 3fdbd1ce11 ("openvswitch: add ipv6 'set' action").
Reported-by: Neal Shrader <icosahedral@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Need to free memory in case of sample action error.
Introduced by commit 651887b0c2 ("openvswitch: Sample
action without side effects").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
Pull arm64 fixes from Catalin Marinas:
- fix EFI stub cache maintenance causing aborts during boot on certain
platforms
- handle byte stores in __clear_user without panicking
- fix race condition in aarch64_insn_patch_text_sync() (instruction
patching)
- Couple of type fixes
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ARCH_PFN_OFFSET should be unsigned long
Correct the race condition in aarch64_insn_patch_text_sync()
arm64: __clear_user: handle exceptions on strb
arm64: Fix data type for physical address
arm64: efi: Fix stub cache maintenance
Pull x86 platform drivers fixlets from Darren Hart:
"Just two patches to remove hp_accel events from the keyboard bus
stream via an i8042 filter"
* tag 'platform-drivers-x86-v3.18-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform: hp_accel: Add SERIO_I8042 as a dependency since it now includes i8042.h/serio.h
platform: hp_accel: add a i8042 filter to remove HPQ6000 data from kb bus stream
Joe Stringer says:
====================
Implement ndo_gso_check() for vxlan nics
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not other
UDP-based encapsulation protocols where the format and size of the header may
differ. This patch series implements a generic ndo_gso_check() for detecting
VXLAN, then reuses it for these NICs.
Implementation shamelessly stolen from Tom Herbert (with minor fixups):
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
v2: Drop i40e/fm10k patches (code diverged; handling separately).
Refactor common code into vxlan_gso_check() helper.
Minor style fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-11-13
Please pull this set of a few more wireless fixes intended for the
3.18 stream...
For the mac80211 bits, Johannes says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
For the iwlwifi bits, Emmanuel says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
On top of that...
Arend van Spriel corrects a channel width conversion that caused a
WARNING in brcmfmac.
Hauke Mehrtens avoids a NULL pointer dereference in b43.
Larry Finger hits a trio of rtlwifi bugs left over from recent
backporting from the Realtek vendor driver.
Miaoqing Pan fixes a clocking problem in ath9k that could affect
packet timestamps and such.
Stanislaw Gruszka addresses an payload alignment issue that has been
plaguing rt2x00.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libata fixes from Tejun Heo:
"The most notable is the revert of lock splitting optimization in ahci.
This also made the IRQ handling threaded even when there's only one
IRQ in use. The conversion missed IRFQ_SHARED leading to screaming
IRQs problem in some cases and the threaded IRQ handling showed
performance regression in some LKP test cases. The changes are
reverted for now. It'll probably be retried once threaded IRQ
handling is removed from ahci.
Other than that, there's one fix for ahci and several patches adding
device IDs"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix AHCI parameters not taken into account
ata: sata_rcar: Add r8a7793 device support
ahci: Add Device IDs for Intel Sunrise Point PCH
ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks
Revert "AHCI: Optimize single IRQ interrupt processing"
Revert "AHCI: Do not acquire ata_host::lock from single IRQ handler"
ata: sata_rcar: Disable DIPM mode for r8a7790 ES1
There could be a signed overflow in the following code.
The expression, (32-logmask) is comprised between 0 and 31 included.
It may be equal to 31.
In such a case the left shift will produce a signed integer overflow.
According to the C99 Standard, this is an undefined behavior.
A simple fix is to replace the signed int 1 with the unsigned int 1U.
Signed-off-by: Vincent BENAYOUN <vincent.benayoun@trust-in-soft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block layer fixes from Jens Axboe:
"Four small fixes that should be merged for the current 3.18-rc series.
This pull request contains:
- a minor bugfix for computation of best IO priority given two
merging requests. From Jan Kara.
- the final (final) merge count issue that has been plaguing
virtio-blk. From Ming Lei.
- enable parallel reinit notify for blk-mq queues, to combine the
cost of an RCU grace period across lots of devices. From Tejun
Heo.
- an error handling fix for the SCSI_IOCTL_SEND_COMMAND ioctl. From
Tony Battersby"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: blk-merge: fix blk_recount_segments()
scsi: Fix more error handling in SCSI_IOCTL_SEND_COMMAND
blk-mq: make mq_queue_reinit_notify() freeze queues in parallel
block: Fix computation of merged request priority
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three regression fixes, two recent (generic power domains,
suspend-to-idle) and one older (cpufreq), an ACPI blacklist entry for
one more machine having problems with Windows 8 compatibility, a minor
cpufreq driver fix (cpufreq-dt) and a fixup for new callback
definitions (generic power domains).
Specifics:
- Fix a crash in the suspend-to-idle code path introduced by a recent
commit that forgot to check a pointer against NULL before
dereferencing it (Dmitry Eremin-Solenikov).
- Fix a boot crash on Exynos5 introduced by a recent commit making
that platform use generic Device Tree bindings for power domains
which exposed a weakness in the generic power domains framework
leading to that crash (Ulf Hansson).
- Fix a crash during system resume on systems where cpufreq depends
on Operation Performance Points (OPP) for functionality, but
CONFIG_OPP is not set. This leads the cpufreq driver registration
to fail, but the resume code attempts to restore the pre-suspend
cpufreq configuration (which does not exist) nevertheless and
crashes. From Geert Uytterhoeven.
- Add a new ACPI blacklist entry for Dell Vostro 3546 that has
problems if it is reported as Windows 8 compatible to the BIOS
(Adam Lee).
- Fix swapped arguments in an error message in the cpufreq-dt driver
(Abhilash Kesavan).
- Fix up the prototypes of new callbacks in struct generic_pm_domain
to make them more useful. Users of those callbacks will be added
in 3.19 and it's better for them to be based on the correct struct
definition in mainline from the start. From Ulf Hansson and Kevin
Hilman"
* tag 'pm+acpi-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix initial default state of the need_restore flag
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
PM / Domains: Change prototype for the attach and detach callbacks
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
ACPI / blacklist: blacklist Win8 OSI for Dell Vostro 3546
Pull firewire fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: The character device file
interface for raw 1394 I/O took uninitialized kernel stack as
substitute for missing ioctl() argument data. This could partially
show up in subsequent read() output"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: cdev: prevent kernel stack leaking into ioctl arguments
Pull vfs fix from Al Viro:
"Fix for a really embarrassing braino in iov_iter. Kudos to paulus..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix thinko in iov_iter_single_seg_count
After removal of the central spinlock nf_conntrack_lock, in
commit 93bb0ceb75 ("netfilter: conntrack: remove central
spinlock nf_conntrack_lock"), it is possible to race against
get_next_corpse().
The race is against the get_next_corpse() cleanup on
the "unconfirmed" list (a per-cpu list with seperate locking),
which set the DYING bit.
Fix this race, in __nf_conntrack_confirm(), by removing the CT
from unconfirmed list before checking the DYING bit. In case
race occured, re-add the CT to the dying list.
While at this, fix coding style of the comment that has been
updated.
Fixes: 93bb0ceb75 ("netfilter: conntrack: remove central spinlock nf_conntrack_lock")
Reported-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: bill bonaparte <programme110@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* pm-domains:
PM / Domains: Fix initial default state of the need_restore flag
PM / Domains: Change prototype for the attach and detach callbacks
* pm-sleep:
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
* pm-cpufreq:
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Pull virtio bugfix from Michael S Tsirkin:
"This fixes a crash in virtio console multi-channel mode that got
introduced in -rc1"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: move early VQ enablement
Pull networking fixes from David Miller:
1) sunhme driver lacks DMA mapping error checks, based upon a report by
Meelis Roos.
2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.
3) DMA memory allocation sizes are wrong in systemport ethernet driver,
fix from Florian Fainelli.
4) Fix use after free in mac80211 defragmentation code, from Johannes
Berg.
5) Some networking uapi headers missing from Kbuild file, from Stephen
Hemminger.
6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
and macvtap has a similar bug, from Herbert Xu.
7) Adjust several tunneling drivers to set dev->iflink after registry,
because registry sets that to -1 overwriting whatever we did. From
Steffen Klassert.
8) Geneve forgets to set inner tunneling type, causing GSO segmentation
to fail on some NICs. From Jesse Gross.
9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
Giuseppe CAVALLARO.
10) Fix spurious timeouts with NewReno on low traffic connections, from
Marcelo Leitner.
11) Fix descriptor updates in enic driver, from Govindarajulu
Varadarajan.
12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
Fix from Takashi Iwai.
13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
Borkmann.
14) psock_fanout selftest accesses past the end of the mmap ring, fix
from Shuah Khan.
15) Fix PTP timestamping for VLAN packets, from Richard Cochran.
16) netlink_unbind() calls in netlink pass wrong initial argument, from
Hiroaki SHIMODA.
17) vxlan socket reuse accidently reuses a socket when the address
family is different, so we have to explicitly check this, from
Marcelo Lietner.
18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
and other architectures, from Guenter Roeck.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
vxlan: Do not reuse sockets for a different address family
smsc911x: power-up phydev before doing a software reset.
lib: rhashtable - Remove weird non-ASCII characters from comments
net/smsc911x: Fix delays in the PHY enable/disable routines
net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
netlink: Properly unbind in error conditions.
net: ptp: fix time stamp matching logic for VLAN packets.
cxgb4 : dcb open-lldp interop fixes
selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
net: bcmgenet: apply MII configuration in bcmgenet_open()
net: bcmgenet: connect and disconnect from the PHY state machine
net: qualcomm: Fix dependency
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
net: phy: Correctly handle MII ioctl which changes autonegotiation.
ipv6: fix IPV6_PKTINFO with v4 mapped
net: sctp: fix memory leak in auth key management
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
net: ppp: Don't call bpf_prog_create() in ppp_lock
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
cxgb4 : Fix bug in DCB app deletion
...
A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The detection of crc_enabled is known to fail for Fujitsu H730. A DMI
blacklist is added for that, but it can be expected that other laptops will
pop up with this.
Here a sysfs knob is provided to alter the behaviour of crc_enabled.
Writing 0 or 1 to it sets the variable to 0 or 1. Reading it will show the
crc_enabled variable (0 or 1).
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the past, no elantech was known with 3 touchpad mouse buttons.
Fujitsu H730 is the first known elantech with a middle button. This commit
enables this middle button. For backwards compatibility, the Fujitsu is
detected via DMI, and only for this one 3 buttons will be announced.
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sometimes on Dell Latitude laptops psmouse/alps driver receive invalid ALPS
protocol V3 packets with bit7 set in last byte. More often it can be
reproduced on Dell Latitude E6440 or E7440 with closed lid and pushing
cover above touchpad.
If bit7 in last packet byte is set then it is not valid ALPS packet. I was
told that ALPS devices never send these packets. It is not know yet who
send those packets, it could be Dell EC, bug in BIOS and also bug in
touchpad firmware...
With this patch alps driver does not process those invalid packets, but
instead of reporting PSMOUSE_BAD_DATA, getting into out of sync state,
getting back in sync with the next byte and spam dmesg we return
PSMOUSE_FULL_PACKET. If driver is truly out of sync we'll fail the checks
on the next byte and report PSMOUSE_BAD_DATA then.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add IIO include files
kernel/panic.c: update comments for print_tainted
mem-hotplug: reset node present pages when hot-adding a new pgdat
mem-hotplug: reset node managed pages when hot-adding a new pgdat
mm/debug-pagealloc: correct freepage accounting and order resetting
fanotify: fix notification of groups with inode & mount marks
mm, compaction: prevent infinite loop in compact_zone
mm: alloc_contig_range: demote pages busy message from warn to info
mm/slab: fix unalignment problem on Malta with EVA due to slab merge
mm/page_alloc: restrict max order of merging on isolated pageblock
mm/page_alloc: move freepage counting logic to __free_one_page()
mm/page_alloc: add freepage on isolate pageblock to correct buddy list
mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype
mm/compaction: skip the range until proper target pageblock is met
zram: avoid kunmap_atomic() of a NULL pointer
Pull Ceph fixes from Sage Weil:
"There is an overflow bug fix for cephfs from Zheng, a fix for handling
large authentication ticket buffers in libceph from Ilya, and a few
fixes for the request handling code from Ilya that affect RBD volumes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: change from BUG to WARN for __remove_osd() asserts
libceph: clear r_req_lru_item in __unregister_linger_request()
libceph: unlink from o_linger_requests when clearing r_osd
libceph: do not crash on large auth tickets
ceph: fix flush tid comparision
Pull HID fixes from Jiri Kosina:
- fix for an oops in HID core upon repeated subdriver insertion/removal
under certain circumstances, by Benjamin Tissoires
- quirk for another Elan Touchscreen device, by Adel Gadllah
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: cleanup .claimed field on disconnect
HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103
When memory is hot-added, all the memory is in offline state. So clear
all zones' present_pages because they will be updated in online_pages()
and offline_pages(). Otherwise, /proc/zoneinfo will corrupt:
When the memory of node2 is offline:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 8388608
managed 0
When we online memory on node2:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 16777216
managed 8388608
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In free_area_init_core(), zone->managed_pages is set to an approximate
value for lowmem, and will be adjusted when the bootmem allocator frees
pages into the buddy system.
But free_area_init_core() is also called by hotadd_new_pgdat() when
hot-adding memory. As a result, zone->managed_pages of the newly added
node's pgdat is set to an approximate value in the very beginning.
Even if the memory on that node has node been onlined,
/sys/device/system/node/nodeXXX/meminfo has wrong value:
hot-add node2 (memory not onlined)
cat /sys/device/system/node/node2/meminfo
Node 2 MemTotal: 33554432 kB
Node 2 MemFree: 0 kB
Node 2 MemUsed: 33554432 kB
Node 2 Active: 0 kB
This patch fixes this problem by reset node managed pages to 0 after
hot-adding a new node.
1. Move reset_managed_pages_done from reset_node_managed_pages() to
reset_all_zones_managed_pages()
2. Make reset_node_managed_pages() non-static
3. Call reset_node_managed_pages() in hotadd_new_pgdat() after pgdat
is initialized
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One thing I did in this patch is fixing freepage accounting. If we
clear guard page and link it onto isolate buddy list, we should not
increase freepage count. This patch adds conditional branch to skip
counting in this case. Without this patch, this overcounting happens
frequently if guard order is set and CMA is used.
Another thing fixed in this patch is the target to reset order. In
__free_one_page(), we check the buddy page whether it is a guard page or
not. And, if so, we should clear guard attribute on the buddy page and
reset order of it to 0. But, current code resets original page's order
rather than buddy one's. Maybe, this doesn't have any problem, because
whole merged page's order will be re-assigned soon. But, it is better
to correct code.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Gioh Kim <gioh.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fsnotify() needs to merge inode and mount marks lists when notifying
groups about events so that ignore masks from inode marks are reflected
in mount mark notifications and groups are notified in proper order
(according to priorities).
Currently the sorting of the lists done by fsnotify_add_inode_mark() /
fsnotify_add_vfsmount_mark() and fsnotify() differed which resulted
ignore masks not being used in some cases.
Fix the problem by always using the same comparison function when
sorting / merging the mark lists.
Thanks to Heinrich Schuchardt for improvements of my patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=87721
Signed-off-by: Jan Kara <jack@suse.cz>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several people have reported occasionally seeing processes stuck in
compact_zone(), even triggering soft lockups, in 3.18-rc2+.
Testing a revert of commit e14c720efd ("mm, compaction: remember
position within pageblock in free pages scanner") fixed the issue,
although the stuck processes do not appear to involve the free scanner.
Finally, by code inspection, the bug was found in isolate_migratepages()
which uses a slightly different condition to detect if the migration and
free scanners have met, than compact_finished(). That has not been a
problem until commit e14c720efd allowed the free scanner position
between individual invocations to be in the middle of a pageblock.
In a relatively rare case, the migration scanner position can end up at
the beginning of a pageblock, with the free scanner position in the
middle of the same pageblock. If it's the migration scanner's turn,
isolate_migratepages() exits immediately (without updating the
position), while compact_finished() decides to continue compaction,
resulting in a potentially infinite loop. The system can recover only
if another process creates enough high-order pages to make the watermark
checks in compact_finished() pass.
This patch fixes the immediate problem by bumping the migration
scanner's position to meet the free scanner in isolate_migratepages(),
when both are within the same pageblock. This causes compact_finished()
to terminate properly. A more robust check in compact_finished() is
planned as a cleanup for better future maintainability.
Fixes: e14c720efd ("mm, compaction: remember position within pageblock in free pages scanner)
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: P. Christeas <xrg@linux.gr>
Tested-by: P. Christeas <xrg@linux.gr>
Link: http://marc.info/?l=linux-mm&m=141508604232522&w=2
Reported-by: Norbert Preining <preining@logic.at>
Tested-by: Norbert Preining <preining@logic.at>
Link: https://lkml.org/lkml/2014/11/4/904
Reported-by: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.org/lkml/2014/11/7/164
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having test_pages_isolated failure message as a warning confuses users
into thinking that it is more serious than it really is. In reality, if
called via CMA, allocation will be retried so a single
test_pages_isolated failure does not prevent allocation from succeeding.
Demote the warning message to an info message and reformat it such that
the text "failed" does not appear and instead a less worrying "PFNS
busy" is used.
This message is trivially reproducible on a 10GB x86 machine on 3.16.y
kernels configured with CONFIG_DMA_CMA.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike SLUB, sometimes, object isn't started at the beginning of the
slab in SLAB. This causes the unalignment problem after slab merging is
supported by commit 12220dea07 ("mm/slab: support slab merge").
Following is the report from Markos that fail to boot on Malta with EVA.
Calibrating delay loop... 19.86 BogoMIPS (lpj=99328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 4096 (order: 0, 16384 bytes)
Mountpoint-cache hash table entries: 4096 (order: 0, 16384 bytes)
Kernel bug detected[#1]:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-05639-g12220dea07f1 #1631
task: 1f04f5d8 ti: 1f050000 task.ti: 1f050000
epc : 80141190 alloc_unbound_pwq+0x234/0x304
Not tainted
ra : 80141184 alloc_unbound_pwq+0x228/0x304
Process swapper/0 (pid: 1, threadinfo=1f050000, task=1f04f5d8, tls=00000000)
Call Trace:
alloc_unbound_pwq+0x234/0x304
apply_workqueue_attrs+0x11c/0x294
__alloc_workqueue_key+0x23c/0x470
init_workqueues+0x320/0x400
do_one_initcall+0xe8/0x23c
kernel_init_freeable+0x9c/0x224
kernel_init+0x10/0x100
ret_from_kernel_thread+0x14/0x1c
[ end trace cb88537fdc8fa200 ]
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
alloc_unbound_pwq() allocates slab object from pool_workqueue. This
kmem_cache requires 256 bytes alignment, but, current merging code
doesn't honor that, and merge it with kmalloc-256. kmalloc-256 requires
only cacheline size alignment so that above failure occurs. However, in
x86, kmalloc-256 is luckily aligned in 256 bytes, so the problem didn't
happen on it.
To fix this problem, this patch introduces alignment mismatch check in
find_mergeable(). This will fix the problem.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reported-by: Markos Chandras <Markos.Chandras@imgtec.com>
Tested-by: Markos Chandras <Markos.Chandras@imgtec.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In free_pcppages_bulk(), we use cached migratetype of freepage to
determine type of buddy list where freepage will be added. This
information is stored when freepage is added to pcp list, so if
isolation of pageblock of this freepage begins after storing, this
cached information could be stale. In other words, it has original
migratetype rather than MIGRATE_ISOLATE.
There are two problems caused by this stale information.
One is that we can't keep these freepages from being allocated.
Although this pageblock is isolated, freepage will be added to normal
buddy list so that it could be allocated without any restriction. And
the other problem is incorrect freepage accounting. Freepages on
isolate pageblock should not be counted for number of freepage.
Following is the code snippet in free_pcppages_bulk().
/* MIGRATE_MOVABLE list may include MIGRATE_RESERVEs */
__free_one_page(page, page_to_pfn(page), zone, 0, mt);
trace_mm_page_pcpu_drain(page, 0, mt);
if (likely(!is_migrate_isolate_page(page))) {
__mod_zone_page_state(zone, NR_FREE_PAGES, 1);
if (is_migrate_cma(mt))
__mod_zone_page_state(zone, NR_FREE_CMA_PAGES, 1);
}
As you can see above snippet, current code already handle second
problem, incorrect freepage accounting, by re-fetching pageblock
migratetype through is_migrate_isolate_page(page).
But, because this re-fetched information isn't used for
__free_one_page(), first problem would not be solved. This patch try to
solve this situation to re-fetch pageblock migratetype before
__free_one_page() and to use it for __free_one_page().
In addition to move up position of this re-fetch, this patch use
optimization technique, re-fetching migratetype only if there is isolate
pageblock. Pageblock isolation is rare event, so we can avoid
re-fetching in common case with this optimization.
This patch also correct migratetype of the tracepoint output.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before describing bugs itself, I first explain definition of freepage.
1. pages on buddy list are counted as freepage.
2. pages on isolate migratetype buddy list are *not* counted as freepage.
3. pages on cma buddy list are counted as CMA freepage, too.
Now, I describe problems and related patch.
Patch 1: There is race conditions on getting pageblock migratetype that
it results in misplacement of freepages on buddy list, incorrect
freepage count and un-availability of freepage.
Patch 2: Freepages on pcp list could have stale cached information to
determine migratetype of buddy list to go. This causes misplacement of
freepages on buddy list and incorrect freepage count.
Patch 4: Merging between freepages on different migratetype of
pageblocks will cause freepages accouting problem. This patch fixes it.
Without patchset [3], above problem doesn't happens on my CMA allocation
test, because CMA reserved pages aren't used at all. So there is no
chance for above race.
With patchset [3], I did simple CMA allocation test and get below
result:
- Virtual machine, 4 cpus, 1024 MB memory, 256 MB CMA reservation
- run kernel build (make -j16) on background
- 30 times CMA allocation(8MB * 30 = 240MB) attempts in 5 sec interval
- Result: more than 5000 freepage count are missed
With patchset [3] and this patchset, I found that no freepage count are
missed so that I conclude that problems are solved.
On my simple memory offlining test, these problems also occur on that
environment, too.
This patch (of 4):
There are two paths to reach core free function of buddy allocator,
__free_one_page(), one is free_one_page()->__free_one_page() and the
other is free_hot_cold_page()->free_pcppages_bulk()->__free_one_page().
Each paths has race condition causing serious problems. At first, this
patch is focused on first type of freepath. And then, following patch
will solve the problem in second type of freepath.
In the first type of freepath, we got migratetype of freeing page
without holding the zone lock, so it could be racy. There are two cases
of this race.
1. pages are added to isolate buddy list after restoring orignal
migratetype
CPU1 CPU2
get migratetype => return MIGRATE_ISOLATE
call free_one_page() with MIGRATE_ISOLATE
grab the zone lock
unisolate pageblock
release the zone lock
grab the zone lock
call __free_one_page() with MIGRATE_ISOLATE
freepage go into isolate buddy list,
although pageblock is already unisolated
This may cause two problems. One is that we can't use this page anymore
until next isolation attempt of this pageblock, because freepage is on
isolate buddy list. The other is that freepage accouting could be wrong
due to merging between different buddy list. Freepages on isolate buddy
list aren't counted as freepage, but ones on normal buddy list are
counted as freepage. If merge happens, buddy freepage on normal buddy
list is inevitably moved to isolate buddy list without any consideration
of freepage accouting so it could be incorrect.
2. pages are added to normal buddy list while pageblock is isolated.
It is similar with above case.
This also may cause two problems. One is that we can't keep these
freepages from being allocated. Although this pageblock is isolated,
freepage would be added to normal buddy list so that it could be
allocated without any restriction. And the other problem is same as
case 1, that it, incorrect freepage accouting.
This race condition would be prevented by checking migratetype again
with holding the zone lock. Because it is somewhat heavy operation and
it isn't needed in common case, we want to avoid rechecking as much as
possible. So this patch introduce new variable, nr_isolate_pageblock in
struct zone to check if there is isolated pageblock. With this, we can
avoid to re-check migratetype in common case and do it only if there is
isolated pageblock or migratetype is MIGRATE_ISOLATE. This solve above
mentioned problems.
Changes from v3:
Add one more check in free_one_page() that checks whether migratetype is
MIGRATE_ISOLATE or not. Without this, abovementioned case 1 could happens.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Heesub Shin <heesub.shin@samsung.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Ritesh Harjani <ritesh.list@gmail.com>
Cc: Gioh Kim <gioh.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 7d49d88683 ("mm, compaction: reduce zone checking frequency in
the migration scanner") has a side-effect that changes the iteration
range calculation. Before the change, block_end_pfn is calculated using
start_pfn, but now it blindly adds pageblock_nr_pages to the previous
value.
This causes the problem that isolation_start_pfn is larger than
block_end_pfn when we isolate the page with more than pageblock order.
In this case, isolation would fail due to an invalid range parameter.
To prevent this, this patch implements skipping the range until a proper
target pageblock is met. Without this patch, CMA with more than
pageblock order always fails but with this patch it will succeed.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kuser helpers page is not set up on non-MMU systems, so it does
not make sense to allow CONFIG_KUSER_HELPERS to be enabled when
CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in
set_tls (used in execve and the arm_syscall trap handler):
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
task: 8b838000 ti: 8b82a000 task.ti: 8b82a000
PC is at flush_thread+0x32/0x40
LR is at flush_thread+0x21/0x40
pc : [<8f00157a>] lr : [<8f001569>] psr: 4100000b
sp : 8b82be20 ip : 00000000 fp : 8b83c000
r10: 00000001 r9 : 88018c84 r8 : 8bb85000
r7 : 8b838000 r6 : 00000000 r5 : 8bb77400 r4 : 8b82a000
r3 : ffff0ff0 r2 : 8b82a000 r1 : 00000000 r0 : 88020354
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
[<8f002bc1>] (unwind_backtrace) from [<8f002033>] (show_stack+0xb/0xc)
[<8f002033>] (show_stack) from [<8f00265b>] (__invalid_entry+0x4b/0x4c)
As best I can tell this issue existed for the set_tls ARM syscall
before commit fbfb872f5f "ARM: 8148/1: flush TLS and thumbee
register state during exec" consolidated the TLS manipulation code
into the set_tls helper function, but now that we're using it to flush
register state during execve, !MMU users encounter the oops at the
first exec.
Prevent CONFIG_MMU=n configurations from enabling
CONFIG_KUSER_HELPERS.
Fixes: fbfb872f5f (ARM: 8148/1: flush TLS and thumbee register state during exec)
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reported-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To speed up decompression, the decompressor sets up a flat, cacheable
mapping of memory. However, when there is insufficient space to hold
the page tables for this mapping, we don't bother to enable the caches
and subsequently skip all the cache maintenance hooks.
Skipping the cache maintenance before jumping to the relocated code
allows the processor to predict the branch and populate the I-cache
with stale data before the relocation loop has completed (since a
bootloader may have SCTLR.I set, which permits normal, cacheable
instruction fetches regardless of SCTLR.M).
This patch moves the cache maintenance check into the maintenance
routines themselves, allowing the v6/v7 versions to invalidate the
I-cache regardless of the MMU state.
Cc: <stable@vger.kernel.org>
Reported-by: Marc Carino <marc.ceeeee@gmail.com>
Tested-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and
of_get_pci_domain_nr()") added parsing of the "linux,pci-domain" property,
but didn't add the binding documentation.
Since this property will be supported by a number of host bridge drivers,
add it to the common PCI binding doc.
Fixes: 41e5c0f81d ("of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
drm/tegra: Fixes for v3.18-rc5
This is a single patch that fixes the VBLANK machinery after:
7ffd7a6851 drm: Always reject drm_vblank_get() after drm_vblank_off()
* tag 'drm/tegra/for-3.18-rc5' of git://people.freedesktop.org/~tagr/linux:
drm/tegra: dc: Add missing call to drm_vblank_on()
One modesetting, one gk20a fix.
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/nv50/disp: Fix modeset on G94
drm/gk20a/fb: fix setting of large page size bit
one regression fix.
* tag 'drm-intel-fixes-2014-11-13' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix obj->map_and_fenceable across tiling changes
Currently, we only match against local port number in order to reuse
socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound
to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will
follow. The following steps reproduce it:
# ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \
srcport 5000 6000 dev eth0
# ip link add vxlan7 type vxlan id 43 group ff0e::110 \
srcport 5000 6000 dev eth0
# ip link set vxlan6 up
# ip link set vxlan7 up
<panic>
[ 4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
...
[ 4.188076] Call Trace:
[ 4.188085] [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630
[ 4.188098] [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan]
[ 4.188113] [<ffffffff810a3430>] process_one_work+0x220/0x710
[ 4.188125] [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710
[ 4.188138] [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0
[ 4.188149] [<ffffffff810a3920>] ? process_one_work+0x710/0x710
So address family must also match in order to reuse a socket.
Reported-by: Jean-Tsung Hsiao <jhsiao@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My editor spewed garbage that looked like memory corruption on
my screen. It turns out that a number of occurences of "fi" got
turned into a ligature.
This patch replaces these ligatures with the ASCII letters "fi".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
kick_requests() can put linger requests on the notarget list. This
means we need to clear the much-overloaded req->r_req_lru_item in
__unregister_linger_request() as well, or we get an assertion failure
in ceph_osdc_release_request() - !list_empty(&req->r_req_lru_item).
AFAICT the assumption was that registered linger requests cannot be on
any of req->r_req_lru_item lists, but that's clearly not the case.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Requests have to be unlinked from both osd->o_requests (normal
requests) and osd->o_linger_requests (linger requests) lists when
clearing req->r_osd. Otherwise __unregister_linger_request() gets
confused and we trip over a !list_empty(&osd->o_linger_requests)
assert in __remove_osd().
MON=1 OSD=1:
# cat remove-osd.sh
#!/bin/bash
rbd create --size 1 test
DEV=$(rbd map test)
ceph osd out 0
sleep 3
rbd map dne/dne # obtain a new osdmap as a side effect
rbd unmap $DEV & # will block
sleep 3
ceph osd in 0
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
TID of cap flush ack is 64 bits, but ceph_inode_info::flushing_cap_tid
is only 16 bits. 16 bits should be plenty to let the cap flush updates
pipeline appropriately, but we need to cast in the proper direction when
comparing these differently-sized versions. So downcast the 64-bits one
to 16 bits.
Reflects ceph.git commit a5184cf46a6e867287e24aeb731634828467cd98.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@redhat.com>
Felipe writes:
usb: fixes for v3.18-rc5
Just one fix here on dwc3 which fixes a minor
bug caused by a fix that went in this v3.18-rc
cycle.
The corner case is minimal as it can only be
reproduced with back-to-back Setup transfers
(without starting data or status phase) by
means of a LeCroy USB Trainer, where we can
generate USB packets any way we like.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The branches of the if (i->type & ITER_BVEC) statement in
iov_iter_single_seg_count() are the wrong way around; if ITER_BVEC is
clear then we use i->bvec, when we should be using i->iov. This fixes
it.
In my case, the symptom that this caused was that a KVM guest doing
filesystem operations on a virtual disk would result in one of qemu's
threads on the host going into an infinite loop in
generic_perform_write(). The loop would hit the copied == 0 case and
call iov_iter_single_seg_count() to reduce the number of bytes to try
to process, but because of the error, iov_iter_single_seg_count()
would just return i->count and the loop made no progress and continued
forever.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull sound fixes from Takashi Iwai:
"Things get calming down, now we have only a few fix patches: a trivial
fix for memory leak in usb-audio, a patch for the new HD-audio PCI id,
a device-specific mute-LED fix, and a slightly big patch to cover the
missing COEF inits of various Realtek codecs"
* tag 'sound-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add mute LED control for Lenovo Ideapad Z560
ALSA: hda/realtek - Change EAPD to verb control
ALSA: usb-audio: Fix memory leak in FTU quirk
ALSA: hda_intel: Add DeviceIDs for Sunrise Point-LP
Pull SELinux fixlet from James Morris:
"WARN_ONCE() here will unnecessarily terrify users"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: convert WARN_ONCE() to printk() in selinux_nlmsg_perm()
Pull audit fixes from Paul Moore:
"After he sent the initial audit pull request for 3.18, Eric asked me
to take over the management of the audit tree, hence this pull request
to fix a couple of problems with audit.
As you can see below, the changes are minimal: adding some whitespace
to a string so userspace parses it correctly, and fixing a problem
with audit's usage of fsnotify that was causing audit watch rules to
be lost. Neither of these patches were very controversial on the
mailing lists and they fix real problems, getting them into 3.18 would
be a good thing"
* 'stable-3.18' of git://git.infradead.org/users/pcmoore/audit:
audit: keep inode pinned
audit: AUDIT_FEATURE_CHANGE message format missing delimiting space
Pull device mapper fixes from Mike Snitzer:
- stable fix for dm-thin that avoids normal IO racing with discard
- stable fix for a dm-cache related bug in dm-btree walking code that
results from using very large fast device (eg 4T) with a very small
cache blocksize (eg 32K) -- this is a very uncommon configuration
- a couple fixes for dm-raid (one for stable and the other addresses a
crash in 3.18-rc1 code)
- stable fix for dm-thinp that addresses a very rare dm-bufio bug
having to do with memory reclaimation (via shrinker) when using
dm-thinp ontop of loopback devices
- fix a leak in dm-stripe target constructor's error path
* tag 'dm-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix a recursion depth bug in btree walking code
dm thin: grab a virtual cell before looking up the mapping
dm raid: fix inaccessible superblocks causing oops in configure_discard_support
dm raid: ensure superblock's size matches device's logical block size
dm bufio: change __GFP_IO to __GFP_FS in shrinker callbacks
dm stripe: fix potential for leak in stripe_ctr error path
The X-Gene PCIe driver assumes pci_scan_root_bus() assigns resources as
proposed in [1]. But we dropped patch [1] because it would break some
architectures, which means the X-Gene PCIe driver is currently broken.
Add calls to scan the bus, assign resources, and add devices in the X-Gene
driver to fix this.
[bhelgaas: changelog]
[1] http://lkml.kernel.org/r/1412000971-9242-11-git-send-email-Liviu.Dudau@arm.com
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vddio_sdmmc3 is a vdd_io, and thus should be under the vqmmc-supply
property, not vmmc-supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This property was wrong and broke eMMC since commit 52221610d ("mmc:
sdhci: Improve external VDD regulator support"). Align the eMMC
properties to those of other Tegra boards.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These labels will be used to provide deterministic numbering of consoles
in a later patch.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
[treding@nvidia.com: drop aliases, reword commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
pfns are unsigned long, but PHYS_PFN_OFFSET is phys_addr_t. This leads
to page_to_pfn() returning phys_addr_t which cause type mismatches in
some print statements.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When experimenting with patches to provide kprobes support for aarch64
smp machines would hang when inserting breakpoints into kernel code.
The hangs were caused by a race condition in the code called by
aarch64_insn_patch_text_sync(). The first processor in the
aarch64_insn_patch_text_cb() function would patch the code while other
processors were still entering the function and incrementing the
cpu_count field. This resulted in some processors never observing the
exit condition and exiting the function. Thus, processors in the
system hung.
The first processor to enter the patching function performs the
patching and signals that the patching is complete with an increment
of the cpu_count field. When all the processors have incremented the
cpu_count field the cpu_count will be num_cpus_online()+1 and they
will return to normal execution.
Fixes: ae16480785 arm64: introduce interfaces to hotpatch kernel and module code
Signed-off-by: William Cohen <wcohen@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64 currently doesn't fix up faults on the single-byte (strb) case of
__clear_user... which means that we can cause a nasty kernel panic as an
ordinary user with any multiple PAGE_SIZE+1 read from /dev/zero.
i.e.: dd if=/dev/zero of=foo ibs=1 count=1 (or ibs=65537, etc.)
This is a pretty obscure bug in the general case since we'll only
__do_kernel_fault (since there's no extable entry for pc) if the
mmap_sem is contended. However, with CONFIG_DEBUG_VM enabled, we'll
always fault.
if (!down_read_trylock(&mm->mmap_sem)) {
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
retry:
down_read(&mm->mmap_sem);
} else {
/*
* The above down_read_trylock() might have succeeded in
* which
* case, we'll have missed the might_sleep() from
* down_read().
*/
might_sleep();
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
}
Fix that by adding an extable entry for the strb instruction, since it
touches user memory, similar to the other stores in __clear_user.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reported-by: Miloš Prchlík <mprchlik@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Use phys_addr_t for physical address in alloc_init_pud. Although
phys_addr_t and unsigned long are 64 bit in arm64, it is better
to use phys_addr_t to describe physical addresses.
Signed-off-by: Min-Hua Chen <orca.chen@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
While efi-entry.S mentions that efi_entry() will have relocated the
kernel image, it actually means that efi_entry will have placed a copy
of the kernel in the appropriate location, and until this is branched to
at the end of efi_entry.S, all instructions are executed from the
original image.
Thus while the flush in efi_entry.S does ensure that the copy is visible
to noncacheable accesses, it does not guarantee that this is true for
the image instructions are being executed from. This could have
disasterous effects when the MMU and caches are disabled if the image
has not been naturally evicted to the PoC.
Additionally, due to a missing dsb following the ic ialluis, the new
kernel image is not necessarily clean in the I-cache when it is branched
to, with similar potentially disasterous effects.
This patch adds additional flushing to ensure that the currently
executing stub text is flushed to the PoC and is thus visible to
noncacheable accesses. As it is placed after the instructions cache
maintenance for the new image and __flush_dcache_area already contains a
dsb, we do not need to add a separate barrier to ensure completion of
the icache maintenance.
Comments are updated to clarify the situation with regard to the two
images and the maintenance required for both.
Fixes: 3c7f255039
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Joel Schopp <joel.schopp@amd.com>
Reviewed-by: Roy Franz <roy.franz@linaro.org>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When the CRTC is enabled, make sure the VBLANK machinery is enabled.
Failure to do so will cause drm_vblank_get() to not enable the VBLANK on
the CRTC and VBLANK-synchronized page-flips won't work.
While at it, get rid of the legacy drm_vblank_pre_modeset() and
drm_vblank_post_modeset() calls that are replaced by drm_vblank_on()
and drm_vblank_off().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lenovo Ideapad Z560 has a mute LED that is controlled via EAPD pin
0x1b on CX20585 codec. (EAPD bit on corresponds to mute LED on.)
The machine doesn't need other EAPD, so the fixup concentrates on
controlling EAPD 0x1b following the vmaster state (but inversely).
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=665315
Reported-by: Szymon Kowalczyk <fazerxlo@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit f5866db6 (virtio_console: enable VQs early) tried to make
sure that DRIVER_OK was set when virtio_console started using its
virtqueues. Doing this in add_port(), however, means that we try
to set DRIVER_OK again when when a port is dynamically added after
the probe function is done.
Let's move virtio_device_ready() to the probe function just before
trying to use the virtqueues instead. This is fine as nothing can
fail inbetween.
Reported-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit "ltc/gf100-: fix cbc issues on certain boards" moved the setting
of the large page size bit from bar/nvc0 to fb/nvc0. GK20A uses its own
FB device and the change was thus not applied to it - fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull kvm fixes from Paolo Bonzini:
"Two fixes --- one of them not exactly a one liner, but things are
calming down on the KVM front at last"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix uninitialized op->type for some immediate values
KVM: s390: virtio_ccw: remove unused variable
Pull Xtensa fixes from Chris Zankel:
- fix umount syscall
- fix ISS and xtfpga Kconfig dependencies so that more randconfigs are
buildable
- add seccomp, getrandom, and memfd_create syscalls
- add defconfigs for KC705 and SMP LX200
- implement pgprot_noncached
* tag 'xtensa-20141109' of git://github.com/czankel/xtensa-linux:
xtensa: xtfpga: add lx200 SMP DTS and defconfig
xtensa: xtfpga: add generic KC705 board config
xtensa: re-wire umount syscall to sys_oldumount
xtensa: xtfpga: only select ethoc when ethernet is available
xtensa: add seccomp, getrandom, and memfd_create syscalls
xtensa: ISS: add BLOCK dependency to BLK_DEV_SIMDISK
xtensa: implement pgprot_noncached
xtensa/uapi: Add definition of TIOC[SG]RS485
atom scratch register race fix.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add locking around atombios scratch space usage
Now exynos drm driver incurs infinite loop issue on multi-platform
reported by Matwey V.Korniliv like below,
http://comments.gmane.org/gmane.comp.video.dri.devel/117622
This issue is because non kms drivers enabled are probed before
a component master tries to bring up. This patch set resolves
the infinite loop issue and also includes fixups relevant to exynos
drm internal issues.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix possible infinite loop issue
drm/exynos: g2d: fix null pointer dereference
drm/exynos: resolve infinite loop issue on non multi-platform
drm/exynos: resolve infinite loop issue on multi-platform
Pull crypto fixes from Herbert Xu:
- stack corruption fix for pseries hwrng driver
- add missing DMA unmap in caam crypto driver
- fix NUMA crash in qat crypto driver
- fix buggy mapping of zero-length associated data in qat crypto driver
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: pseries - port to new read API and fix stack corruption
crypto: caam - fix missing dma unmap on error path
crypto: qat - Enforce valid numa configuration
crypto: qat - Prevent dma mapping zero length assoc data
Any attempt to call nfs_remove_bad_delegation() while a delegation is being
returned is currently a no-op. This means that we can end up looping
forever in nfs_end_delegation_return() if something causes the delegation
to be revoked.
This patch adds a mechanism whereby the state recovery code can communicate
to the delegation return code that the delegation is no longer valid and
that it should not be used when reclaiming state.
It also changes the return value for nfs4_handle_delegation_recall_error()
to ensure that nfs_end_delegation_return() does not reattempt the lock
reclaim before state recovery is done.
http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Pull tracing fix from Steven Rostedt:
"Rabin Vincent found a way that tracing could cause an infinite loop in
the kernel. The splice logic wants a full page from the ring buffer
but the ring_buffer_wait() returns when there's any data in the ring
buffer. The splice code would then continue the loop waiting for a
full page. But if a full page never happens, the splice code will
never sleep and just continue to loop.
There's another case that Rabin fixed that could loop if there's no
memory and kmalloc() constantly returns NULL"
* tag 'trace-fixes-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not risk busy looping in buffer splice
tracing: Do not busy wait in buffer splice
This patch removes the assumption made previously, that we only need to
check the delegation stateid when it matches the stateid on a cached
open.
If we believe that we hold a delegation for this file, then we must assume
that its stateid may have been revoked or expired too. If we don't test it
then our state recovery process may end up caching open/lock state in a
situation where it should not.
We therefore rename the function nfs41_clear_delegation_stateid as
nfs41_check_delegation_stateid, and change it to always run through the
delegation stateid test and recovery process as outlined in RFC5661.
http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Pull kernel argument parsing fix from Rusty Russell:
"Nasty, stupid bug, and I've suddenly had two reports"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
param: fix crash on bad kernel arguments
Pull hwmon fixes from Guenter Roeck:
- fix PCI device ID in fam15h_power driver
- fix suspend/resume behavior in pwm-fan driver
- reduce logging noise created by ibmpowernv driver
* tag 'hwmon-for-linus-v3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (fam15h_power) Fix NB device ID for F16h M30h
hwmon: (pwm-fan) Fix suspend/resume behavior
hwmon: (ibmpowernv) Quieten when probing finds no device
Pull thermal driver fixes from Eduardo Valentin:
"This week we have few fixes:
- fix in IMX thermal driver to do the correct loading sequence with
CPUfreq
- fix in Exynos related to TMU_CONTROL offset in Exynos5260
- fix the unit conversion in int3403"
[ Still pulling from Eduardo as Rui Zhang is on a business trip and has
troubles with his machine ]
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
imx: thermal: imx_get_temp might be called before sensor clock is prepared
thermal: exynos: use correct offset for TMU_CONTROL register on Exynos5260
thermal: imx: correct driver load sequence for cpu cooling
Thermal/int3403: Fix thermal hysteresis unit conversion
Convert WARN_ONCE() to printk() in selinux_nlmsg_perm().
After conversion from audit_log() in commit e173fb26, WARN_ONCE() was
deemed too alarmist, so switch it to printk().
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: Changed to printk(WARNING) so we catch all of the different
invalid netlink messages. In Richard's defense, he brought this
point up earlier, but I didn't understand his point at the time.]
Signed-off-by: Paul Moore <pmoore@redhat.com>
Pull drm fixes from Dave Airlie:
"Radeon and i915 fixes.
I probably should have sent these earlier, but nothing too urgent in
them:
- i915:
blackscreen and corruption fixes
- radeon:
oops, locking and stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: add missing crtc unlock when setting up the MC
drm/radeon: use gart for DMA IB tests
drm/radeon: make sure mode init is complete in bandwidth_update
drm/radeon: set correct CE ram size for CIK
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
Even if netlink_kernel_cfg::unbind is implemented the unbind() method is
not called, because cfg->unbind is omitted in __netlink_kernel_create().
And fix wrong argument of test_bit() and off by one problem.
At this point, no unbind() method is implemented, so there is no real
issue.
Fixes: 4f52090052 ("netlink: have netlink per-protocol bind function return an error code.")
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Cc: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* In LLD_MANAGED mode, traffic classes were being returned in reverse order to
lldp agent.
* Priotype of strict is no longer the default returned.
* Change behaviour of getdcbx() based on discussions on lldp-devel
These were missed as there was no working fetch interface for open-lldp when
running in LLD_MANAGED mode till now.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow the nfs_v4_1_minor_ops had the NFS_CAP_SEEK flag set, enabling
SEEK over v4.1. This is wrong, and can make servers crash.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Tested-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Variable 'err' needn't be initialized when nfs_getattr() uses it to
check whether it should call generic_fillattr() or not. That can result
in spurious error returns. Initialize 'err' properly.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Commit 3a6fd1f004 (pnfs/blocklayout: remove read-modify-write handling
in bl_write_pagelist) introduced a bogus assignment pg_index = pg_index
in variable initialization. AFAICS it's just a typo so remove it.
Spotted by Coverity (id 1248711).
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This WARN_ON_ONCE was supposed to catch reference counting bugs, but can
trigger in inappropriate situations.
This was reproducible using NFSv2 on an architecture with 64K pages -- we
verified that it was not a reference counting bug and the warning was
safe to ignore.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
For pNFS direct writes, layout driver may dynamically allocate ds_cinfo.buckets.
So we need to take care to free them when freeing dreq.
Ideally this needs to be done inside layout driver where ds_cinfo.buckets
are allocated. But buckets are attached to dreq and reused across LD IO iterations.
So I feel it's OK to free them in the generic layer.
Cc: stable@vger.kernel.org [v3.4+]
Signed-off-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
In commit a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver"),
the I2C part of the CS42L51 was moved to a separate file, but the
definition of the of_device_id array was left in the driver file
itself, no longer connected to the platform_driver structure using the
.of_match_table pointer.
This commit exports the of_device_id array in cs42l51, and uses it as
.of_match_able in cs42l51-i2c.c. This solution was suggested by Brian
Austin.
Fixes: a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The existing xtables matches and targets, when used from nft_compat, may
sleep from the destroy path, ie. when removing rules. Since the objects
are released via call_rcu from softirq context, this results in lockdep
splats and possible lockups that may be hard to reproduce.
Patrick also indicated that delayed object release via call_rcu can
cause us problems in the ordering of event notifications when anonymous
sets are in place.
So, this patch restores the synchronous object release from the commit
and abort paths. This includes a call to synchronize_rcu() to make sure
that no packets are walking on the objects that are going to be
released. This is slowier though, but it's simple and it resolves the
aforementioned problems.
This is a partial revert of c7c32e7 ("netfilter: nf_tables: defer all
object release via rcu") that was introduced in 3.16 to speed up
interaction with userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of the match->name, which is of course not relevant.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check for nat chain dependency only, which is the one that can
actually crash the kernel. Don't care if mangle, filter and security
specific match and targets are used out of their scope, they are
harmless.
This restores iptables-compat with mangle specific match/target when
used out of the OUTPUT chain, that are actually emulated through filter
chains, which broke when performing strict validation.
Fixes: f3f5dde ("netfilter: nft_compat: validate chain type in match/target")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This will fix no sound in Linux system after reboot from windows.
Change log:
- alc662_fill_coef() is replaced with alc_fill_eapd_coef_idx()
and move into alc_auto_init_amp().
- For ALC262, ALC267, ALC268, ALC269, ALC233, ALC255, ALC280, ALC282,
ALC283, ALC284, ALC285, ALC286, ALC288, ALC290, ALC292, ALC293, ALC294,
ALC668, ALC888VC, ALC888VD, ALC891, ALC892, ALC898 and ALC1150, add update
COEF control for EAPD setting.
- Remove alc269_fill_coef() for update EAPD control line.
ADDITIONAL NOTE:
Many Realtek cdoecs have a COEF bit to switch the master amp control
between COEF and EAPD. Windows drivers seem using COEF while we use
EAPD, which is more standard. As a result, some system suffer from
the silent output when booting after Windows. This patch sets the
COEF bits on the relevant codecs properly to switch to EAPD control.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87771
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prep_memcpy call was not setting any meaningful burst and width because it
was relying on the dma_slave_config was not set already.
Rework the needed conversion functions, and hardcode the width and burst to
use.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The while loop in sock_fanout_read_ring() checks mmap region
bounds after access, causing it to segfault. Fix it to check
count before accessing header->tp_status. This problem can be
reproduced consistently when the test in run as follows:
make -C tools/testing/selftests TARGETS=net run_tests
or
make run_tests from tools/testing/selftests
or
make run_test from tools/testing/selftests/net
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_vs_prepare_tunneled_skb() ignores ->sk when allocating a new
skb, either unconditionally setting ->sk to NULL or allowing
the uninitialized ->sk from a newly allocated skb to leak through
to the caller.
This patch properly copies ->sk and increments its reference count.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
On sh73a0/kzm9g-legacy, probing of the i2c masters fails with:
i2c-sh_mobile i2c-sh_mobile.0: timing values out of range: L/H=0x208/0x1bf
sh_mobile: probe of i2c-sh_mobile.0 failed with error -22
According to the datasheet, the transfer rate is derived from the HP
clock (which runs at 104 MHz) divided by two. Hence
i2c_sh_mobile_platform_data.clks_per_count should be set to two.
Now probing succeeds, and i2c works:
i2c-sh_mobile i2c-sh_mobile.0: I2C adapter 0 with bus speed 100000 Hz (L/H=0x104/0xe0)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For cloned bio, bio->bi_vcnt can't be used at all, and we
have resort to bio_segments() to figure out how many
segment there are in the bio.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Florian Fainelli says:
====================
net: bcmgenet: power management related fixes
These two patches fixes issues seen while testing power management on
platforms using the GENET driver.
First patch fixes an issue with the PHY state machine queuing work after
resume since we are not properly detached from it.
Second patch fixes an issue with GENET interfaces that were not properly
restored to a working state after a S3 suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While developing MST support I noticed I often got the wrong data
back from a transaction, in a racy fashion. I noticed the scratch
space wasn't locked against concurrent users.
Based on a patch by Alex, but I've made it a bit more obvious when
things are locked.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The initial state of the device's need_restore flag should'nt depend on
the current state of the PM domain. For example it should be perfectly
valid to attach an inactive device to a powered PM domain.
The pm_genpd_dev_need_restore() API allow us to update the need_restore
flag to somewhat cope with such scenarios. Typically that should have
been done from drivers/buses ->probe() since it's those that put the
requirements on the value of the need_restore flag.
Until recently, the Exynos SOCs were the only user of the
pm_genpd_dev_need_restore() API, though invoking it from a centralized
location while adding devices to their PM domains.
Due to that Exynos now have swithed to the generic OF-based PM domain
look-up, it's no longer possible to invoke the API from a centralized
location. The reason is because devices are now added to their PM
domains during the probe sequence.
Commit "ARM: exynos: Move to generic PM domain DT bindings"
did the switch for Exynos to the generic OF-based PM domain look-up,
but it also removed the call to pm_genpd_dev_need_restore(). This
caused a regression for some of the Exynos drivers.
To handle things more properly in the generic PM domain, let's change
the default initial value of the need_restore flag to reflect that the
state is unknown. As soon as some of the runtime PM callbacks gets
invoked, update the initial value accordingly.
Moreover, since the generic PM domain is verifying that all devices
are both runtime PM enabled and suspended, using pm_runtime_suspended()
while pm_genpd_poweroff() is invoked from the scheduled work, we can be
sure of that the PM domain won't be powering off while having active
devices.
Do note that, the generic PM domain can still only know about active
devices which has been activated through invoking its runtime PM resume
callback. In other words, buses/drivers using pm_runtime_set_active()
during ->probe() will still suffer from a race condition, potentially
probing a device without having its PM domain being powered. That issue
will have to be solved using a different approach.
This a log from the boot regression for Exynos5, which is being fixed in
this patch.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 308 at ../drivers/clk/clk.c:851 clk_disable+0x24/0x30()
Modules linked in:
CPU: 0 PID: 308 Comm: kworker/0:1 Not tainted 3.18.0-rc3-00569-gbd9449f-dirty #10
Workqueue: pm pm_runtime_work
[<c0013c64>] (unwind_backtrace) from [<c0010dec>] (show_stack+0x10/0x14)
[<c0010dec>] (show_stack) from [<c03ee4cc>] (dump_stack+0x70/0xbc)
[<c03ee4cc>] (dump_stack) from [<c0020d34>] (warn_slowpath_common+0x64/0x88)
[<c0020d34>] (warn_slowpath_common) from [<c0020d74>] (warn_slowpath_null+0x1c/0x24)
[<c0020d74>] (warn_slowpath_null) from [<c03107b0>] (clk_disable+0x24/0x30)
[<c03107b0>] (clk_disable) from [<c02cc834>] (gsc_runtime_suspend+0x128/0x160)
[<c02cc834>] (gsc_runtime_suspend) from [<c0249024>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c0249024>] (pm_generic_runtime_suspend) from [<c024f44c>] (pm_genpd_default_save_state+0x2c/0x8c)
[<c024f44c>] (pm_genpd_default_save_state) from [<c024ff2c>] (pm_genpd_poweroff+0x224/0x3ec)
[<c024ff2c>] (pm_genpd_poweroff) from [<c02501b4>] (pm_genpd_runtime_suspend+0x9c/0xcc)
[<c02501b4>] (pm_genpd_runtime_suspend) from [<c024a4f8>] (__rpm_callback+0x2c/0x60)
[<c024a4f8>] (__rpm_callback) from [<c024a54c>] (rpm_callback+0x20/0x74)
[<c024a54c>] (rpm_callback) from [<c024a930>] (rpm_suspend+0xd4/0x43c)
[<c024a930>] (rpm_suspend) from [<c024bbcc>] (pm_runtime_work+0x80/0x90)
[<c024bbcc>] (pm_runtime_work) from [<c0032a9c>] (process_one_work+0x12c/0x314)
[<c0032a9c>] (process_one_work) from [<c0032cf4>] (worker_thread+0x3c/0x4b0)
[<c0032cf4>] (worker_thread) from [<c003747c>] (kthread+0xcc/0xe8)
[<c003747c>] (kthread) from [<c000e738>] (ret_from_fork+0x14/0x3c)
---[ end trace 40cd58bcd6988f12 ]---
Fixes: a4a8c2c496 (ARM: exynos: Move to generic PM domain DT bindings)
Reported-and-tested0by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Cc: stable@vger.kernel.org
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When advertised capabilities are changed with mii-tool, such as:
mii-tool -A 10baseT
the existing handler has two errors.
- An actual PHY register value is provided by mii-tool, and this
must be mapped to internal state with mii_adv_to_ethtool_adv_t().
- The PHY state machine needs to be told that autonegotiation has
again been performed. If not, the MAC will not be notified of
the new link speed and duplex, resulting in a possible config
mismatch.
Signed-off-by: Brian Hill <Brian@houston-radar.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
chandef_to_chanspec.isra.11+0x158/0x184()
Modules linked in:
CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f #8
[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---
Cc: stable@vger.kernel.org # v3.17
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911https://bugzilla.kernel.org/show_bug.cgi?id=72471http://marc.info/?l=linux-wireless&m=139108549530402&w=2https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use IS_ENABLED(CONFIG_IPV6), to enable this code if IPv6 is
a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: c8e6ad0829 ("ipv6: honor IPV6_PKTINFO with v4 mapped addresses on sendmsg")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A very minimal and simple user space application allocating an SCTP
socket, setting SCTP_AUTH_KEY setsockopt(2) on it and then closing
the socket again will leak the memory containing the authentication
key from user space:
unreferenced object 0xffff8800837047c0 (size 16):
comm "a.out", pid 2789, jiffies 4296954322 (age 192.258s)
hex dump (first 16 bytes):
01 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff816d7e8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811c88d8>] __kmalloc+0xe8/0x270
[<ffffffffa0870c23>] sctp_auth_create_key+0x23/0x50 [sctp]
[<ffffffffa08718b1>] sctp_auth_set_key+0xa1/0x140 [sctp]
[<ffffffffa086b383>] sctp_setsockopt+0xd03/0x1180 [sctp]
[<ffffffff815bfd94>] sock_common_setsockopt+0x14/0x20
[<ffffffff815beb61>] SyS_setsockopt+0x71/0xd0
[<ffffffff816e58a9>] system_call_fastpath+0x12/0x17
[<ffffffffffffffff>] 0xffffffffffffffff
This is bad because of two things, we can bring down a machine from
user space when auth_enable=1, but also we would leave security sensitive
keying material in memory without clearing it after use. The issue is
that sctp_auth_create_key() already sets the refcount to 1, but after
allocation sctp_auth_set_key() does an additional refcount on it, and
thus leaving it around when we free the socket.
Fixes: 65b07e5d0d ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SCTP server doing ASCONF will panic on malformed INIT ping-of-death
in the form of:
------------ INIT[PARAM: SET_PRIMARY_IP] ------------>
While the INIT chunk parameter verification dissects through many things
in order to detect malformed input, it misses to actually check parameters
inside of parameters. E.g. RFC5061, section 4.2.4 proposes a 'set primary
IP address' parameter in ASCONF, which has as a subparameter an address
parameter.
So an attacker may send a parameter type other than SCTP_PARAM_IPV4_ADDRESS
or SCTP_PARAM_IPV6_ADDRESS, param_type2af() will subsequently return 0
and thus sctp_get_af_specific() returns NULL, too, which we then happily
dereference unconditionally through af->from_addr_param().
The trace for the log:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000078
IP: [<ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
PGD 0
Oops: 0000 [#1] SMP
[...]
Pid: 0, comm: swapper Not tainted 2.6.32-504.el6.x86_64 #1 Bochs Bochs
RIP: 0010:[<ffffffffa01e9c62>] [<ffffffffa01e9c62>] sctp_process_init+0x492/0x990 [sctp]
[...]
Call Trace:
<IRQ>
[<ffffffffa01f2add>] ? sctp_bind_addr_copy+0x5d/0xe0 [sctp]
[<ffffffffa01e1fcb>] sctp_sf_do_5_1B_init+0x21b/0x340 [sctp]
[<ffffffffa01e3751>] sctp_do_sm+0x71/0x1210 [sctp]
[<ffffffffa01e5c09>] ? sctp_endpoint_lookup_assoc+0xc9/0xf0 [sctp]
[<ffffffffa01e61f6>] sctp_endpoint_bh_rcv+0x116/0x230 [sctp]
[<ffffffffa01ee986>] sctp_inq_push+0x56/0x80 [sctp]
[<ffffffffa01fcc42>] sctp_rcv+0x982/0xa10 [sctp]
[<ffffffffa01d5123>] ? ipt_local_in_hook+0x23/0x28 [iptable_filter]
[<ffffffff8148bdc9>] ? nf_iterate+0x69/0xb0
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[<ffffffff8148bf86>] ? nf_hook_slow+0x76/0x120
[<ffffffff81496d10>] ? ip_local_deliver_finish+0x0/0x2d0
[...]
A minimal way to address this is to check for NULL as we do on all
other such occasions where we know sctp_get_af_specific() could
possibly return with NULL.
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ppp_ioctl(), bpf_prog_create() is called inside ppp_lock, which
eventually calls vmalloc() and hits BUG_ON() in vmalloc.c. This patch
works around the problem by moving the allocation outside the lock.
The bug was revealed by the recent change in net/core/filter.c, as it
allocates via vmalloc() instead of kmalloc() now.
Reported-and-tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Audit rules disappear when an inode they watch is evicted from the cache.
This is likely not what we want.
The guilty commit is "fsnotify: allow marks to not pin inodes in core",
which didn't take into account that audit_tree adds watches with a zero
mask.
Adding any mask should fix this.
Fixes: 90b1e7a578 ("fsnotify: allow marks to not pin inodes in core")
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Paul Moore <pmoore@redhat.com>
F3 device ID is wrongly included in fam15h_power_id_table
for F16h M30h. It should be F4 device ID. Fix this.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The state of a PWM output is not clearly defined after resume. Some PWM
drivers do not restore the duty cycle upon resume, thus it is necessary to
manually restore the correct value.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Because we build kernels with drivers built in for many platforms, it's
normal for the ibmpowernv driver to be loaded on systems that don't have
the appropriate hardware.
Currently the driver spams the log with:
ibmpowernv ibmpowernv.0: Opal node 'sensors' not found
ibmpowernv: Platfrom driver probe failed
But there is no error, this machine is not a powernv and doesn't have
the hardware. So change the sensors message to dev_dbg(), and only print
an error about the probe failing if it's not ENODEV.
Also fix the spelling of "Platfrom" and print the actual error value.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currenly we only support Large-Send and TX checksum offloads for
encapsulated traffic of type VXLAN. We must make sure to advertize
these offloads up to the stack only when VXLAN tunnel is set.
Failing to do so, would mislead the the networking stack to assume
that the driver can offload the internal TX checksum for GRE packets
and other buggy schemes.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M-audio FastTrack Ultra quirk doesn't release the kzalloc'ed memory.
This patch adds the private_free callback to release it properly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We could be reading 8 bytes into a 4 byte buffer here. It seems
harmless but adding a check is the right thing to do and it silences a
static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As obj->map_and_fenceable computation has changed to only be set when
the object is bound inside the global GTT (and is suitable aligned to a
fence region) we need to accommodate those changes when the tiling is
adjusted. The easiest solution is to unbind from the global GTT if we
are currently fenceable, but will not be after the tiling change.
The bug has been exposed by
commit f8fcadba218fe6d23b2e353fea1cf0a4be4c9454
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Oct 31 13:53:52 2014 +0000
drm/i915: Only mark as map-and-fenceable when bound into the GGTT
which tried to fix an oversight from
commit e6a844687c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 11 12:00:12 2014 +0200
drm/i915: Force CPU relocations if not GTT mapped
which changed the handling of obj->map_and_fenceable.
Note that the alignment check is a vestige from our attempts to reduce
the alignment requirements of tiled but unfenced buffers on
gen2/3. Also, that was when unbinding from the GTT meant UC writes and
clflushing, so we went to great pains to avoid such.
That leaves the actual bug of setting map_and_fenceable to true if we're
not bound to ggtt, which violates the change introduced in the above
patch. Unbinding in that case really looks like the simplest and safest
option, we have to do it anyway.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85896
Testcase: igt/gem_concurrent_blit/gttX*
Tested-by: huax.lu@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Valtteri Rantala <valtteri.rantala@intel.com>
[Jani: amend commit message per input from Daniel and bisect result from
Valtteri]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently if the user passes an invalid value on the kernel command line
then the kernel will crash during argument parsing. On most systems this
is very hard to debug because the console hasn't been initialized yet.
This is a regression due to commit 51e158c12a ("param: hand arguments
after -- straight to init") which, in response to the systemd debug
controversy, made it possible to explicitly pass arguments to init. To
achieve this parse_args() was extended from simply returning an error
code to returning a pointer. Regretably the new init args logic does not
perform a proper validity check on the pointer resulting in a crash.
This patch fixes the validity check. Should the check fail then no arguments
will be passed to init. This is reasonable and matches how the kernel treats
its own arguments (i.e. no error recovery).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make hp_accel dependent on SERIO_I8042 in the Kconfig because since commit
a4c724d072 ('platform: hp_accel: add a i8042
filter to remove HPQ6000 data from kb bus stream') hp_accel includes i8042.h
and serio.h.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Giedrius Statkevičius <giedriuswork@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Fix an error path in SCSI_IOCTL_SEND_COMMAND that calls
blk_put_request(rq) on an invalid IS_ERR(rq) pointer.
Fixes: a492f07545 ("block,scsi: fixup blk_get_request dead queue scenarios")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For PIN_OUTPUT_PULLUP and PIN_OUTPUT_PULLDOWN we must not set the
PULL_DIS bit which disables the PULLs.
PULL_ENA is a 0 and using it in an OR operation is a NOP, so don't
use it in the PIN_OUTPUT_PULLUP/DOWN macros.
Fixes: 23d9cec07c ("pinctrl: dra: dt-bindings: Fix pull enable/disable")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the read loop in trace_buffers_splice_read() keeps failing due to
memory allocation failures without reading even a single page then this
function will keep busy looping.
Remove the risk for that by exiting the function if memory allocation
failures are seen.
Link: http://lkml.kernel.org/r/1415309167-2373-2-git-send-email-rabin@rab.in
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
On a !PREEMPT kernel, attempting to use trace-cmd results in a soft
lockup:
# trace-cmd record -e raw_syscalls:* -F false
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [trace-cmd:61]
...
Call Trace:
[<ffffffff8105b580>] ? __wake_up_common+0x90/0x90
[<ffffffff81092e25>] wait_on_pipe+0x35/0x40
[<ffffffff810936e3>] tracing_buffers_splice_read+0x2e3/0x3c0
[<ffffffff81093300>] ? tracing_stats_read+0x2a0/0x2a0
[<ffffffff812d10ab>] ? _raw_spin_unlock+0x2b/0x40
[<ffffffff810dc87b>] ? do_read_fault+0x21b/0x290
[<ffffffff810de56a>] ? handle_mm_fault+0x2ba/0xbd0
[<ffffffff81095c80>] ? trace_event_buffer_lock_reserve+0x40/0x80
[<ffffffff810951e2>] ? trace_buffer_lock_reserve+0x22/0x60
[<ffffffff81095c80>] ? trace_event_buffer_lock_reserve+0x40/0x80
[<ffffffff8112415d>] do_splice_to+0x6d/0x90
[<ffffffff81126971>] SyS_splice+0x7c1/0x800
[<ffffffff812d1edd>] tracesys_phase2+0xd3/0xd8
The problem is this: tracing_buffers_splice_read() calls
ring_buffer_wait() to wait for data in the ring buffers. The buffers
are not empty so ring_buffer_wait() returns immediately. But
tracing_buffers_splice_read() calls ring_buffer_read_page() with full=1,
meaning it only wants to read a full page. When the full page is not
available, tracing_buffers_splice_read() tries to wait again with
ring_buffer_wait(), which again returns immediately, and so on.
Fix this by adding a "full" argument to ring_buffer_wait() which will
make ring_buffer_wait() wait until the writer has left the reader's
page, i.e. until full-page reads will succeed.
Link: http://lkml.kernel.org/r/1415645194-25379-1-git-send-email-rabin@rab.in
Cc: stable@vger.kernel.org # 3.16+
Fixes: b1169cc69b ("tracing: Remove mock up poll wait function")
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Switch over the msgctl, shmat, shmctl and semtimedop syscalls to use the compat
layer. The problem was found with the debian procenv package, which called
shmctl(0, SHM_INFO, &info);
in which the shmctl syscall then overwrote parts of the surrounding areas on
the stack on which the info variable was stored and thus lead to a segfault
later on.
Additionally fix the definition of struct shminfo64 to use unsigned longs like
the other architectures. This has no impact on userspace since we only have a
32bit userspace up to now.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.10+
commit 6856d30 (usb: dwc3: ep0: return early
on NULL requests) tried to fix a minor corner
case where we could dereference a NULL pointer
but it also ended up introducing some dead code.
Unfortunately, that dead code, if reached, could
end up starving the endpoint request list because
a request would never be given back when it should.
Fix this by moving the check for empty request list
before its first use.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DRA7(including AM5x) and AM47x series are handled under OMAP umbrella.
These SoC support and dts have been added since 3.14 kernel and Pull
requests for these have come in from OMAP till date.
So just ensure that get_maintainers can pick up this list as well.
Cc: linux-omap@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files are very important to the healt
of the OMAP architecture, specially when it
comes to PM support which currently we have
working for at least OMAP3 and we'd like
to know about any changes being made to our
PMICs and IRQ controllers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The walk code was using a 'ro_spine' to hold it's locked btree nodes.
But this data structure is designed for the rolling lock scheme, and
as such automatically unlocks blocks that are two steps up the call
chain. This is not suitable for the simple recursive walk algorithm,
which retraces its steps.
This code is only used by the persistent array code, which in turn is
only used by dm-cache. In order to trigger it you need to have a
mapping tree that is more than 2 levels deep; which equates to 8-16
million cache blocks. For instance a 4T ssd with a very small block
size of 32k only just triggers this bug.
The fix just places the locked blocks on the stack, and stops using
the ro_spine altogether.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Unlike CEE, IEEE has a bespoke app delete call and does not rely on priority
for app deletion
Fixes : 2376c879b8 ('cxgb4 : Improve handling of DCB negotiation or loss
thereof')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
cxgb4/cxgb4vf: Misc. fixes for cxgb4vf
For T5 use Packing and Padding Boundaries for SGE DMA transfers, move
fl_starve_thres to adpater structure, since they are different for each
adapter. The cxgb4vf driver's Free List Starvation Threshold needs to be larger
than the SGE's Egress Congestion Threshold or we'll end up in a mutual stall
where the driver waits for Ingress Packets to drive replacing Free List
Pointers and the SGE waits for Free List Pointers before pushing Ingress
Packets to the host.
The patches series is created against 'net' tree.
And includes patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Free List Starvation Threshold needs to be larger than the SGE's Egress
Congestion Threshold or we'll end up in a mutual stall where the driver waits
for Ingress Packets to drive replacing Free List Pointers and the SGE waits for
Free List Pointers before pushing Ingress Packets to the host.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T5 introduces the ability to have separate Packing and Padding Boundaries
for SGE DMA transfers from the chip to Host Memory. This change set takes
advantage of that to set up a smaller Padding Boundary to conserve PCI Link
and Memory Bandwidth with T5.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter. Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_read and phy_write are not set for every phy any more sine this:
commit d342b95dd7
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Thu Jul 31 21:59:43 2014 +0200
b43: don't duplicate common PHY read/write ops
b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.
This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731
Reported-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: Volker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When transferring from the original range in nf_nat_masquerade_{ipv4,ipv6}()
we copy over values from stack in from min_proto/max_proto due to uninitialized
range variable in both, nft_masq_{ipv4,ipv6}_eval. As we only initialize
flags at this time from nft_masq struct, just zero out the rest.
Fixes: 9ba1f726be ("netfilter: nf_tables: add new nft_masq expression")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull two fixes for early microcode loader on 32-bit from Borislav Petkov:
- access the dis_ucode_ldr chicken bit properly
- fix patch stashing on AMD on 32-bit
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset
configuration") enabled configuring the PM features for twl4030.
This caused poweroff command to fail on devices that have the
BCI charger on twl4030 wired, or have power wired for VBUS.
Instead of powering off, the device reboots. This is because
voltage is detected on charger or VBUS with the default bits
enabled for the power transition registers.
To fix the issue, let's just clear VBUS and CHG bits as we want
poweroff command to keep the system powered off.
Fixes: e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.
The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.
However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:
viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't
built when PM is disabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 8ae80ed173 "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 3.17
Connection retries were not being cleaned up correctly if they failed as a
result of link down. Applies on top of drivers-for-3.18.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler. Since commit
14216561e1 we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.
Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Meelis Roos <meelis.roos@ut.ee>
Tested-by: Meelis Roos <meelis.roos@ut.ee>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf4 ("x86, microcode, AMD: Fix early ucode loading")
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Borislav Petkov <bp@suse.de>
On latest mm + KASan patchset I've got this:
==================================================================
BUG: AddressSanitizer: out of bounds access in sched_init_smp+0x3ba/0x62c at addr ffff88006d4bee6c
=============================================================================
BUG kmalloc-8 (Not tainted): kasan error
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in alloc_vfsmnt+0xb0/0x2c0 age=75 cpu=0 pid=0
__slab_alloc+0x4b4/0x4f0
__kmalloc_track_caller+0x15f/0x1e0
kstrdup+0x44/0x90
alloc_vfsmnt+0xb0/0x2c0
vfs_kern_mount+0x35/0x190
kern_mount_data+0x25/0x50
pid_ns_prepare_proc+0x19/0x50
alloc_pid+0x5e2/0x630
copy_process.part.41+0xdf5/0x2aa0
do_fork+0xf5/0x460
kernel_thread+0x21/0x30
rest_init+0x1e/0x90
start_kernel+0x522/0x531
x86_64_start_reservations+0x2a/0x2c
x86_64_start_kernel+0x15b/0x16a
INFO: Slab 0xffffea0001b52f80 objects=24 used=22 fp=0xffff88006d4befc0 flags=0x100000000004080
INFO: Object 0xffff88006d4bed20 @offset=3360 fp=0xffff88006d4bee70
Bytes b4 ffff88006d4bed10: 00 00 00 00 00 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a ........ZZZZZZZZ
Object ffff88006d4bed20: 70 72 6f 63 00 6b 6b a5 proc.kk.
Redzone ffff88006d4bed28: cc cc cc cc cc cc cc cc ........
Padding ffff88006d4bee68: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G B 3.18.0-rc3-mm1+ #108
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
ffff88006d4be000 0000000000000000 ffff88006d4bed20 ffff88006c86fd18
ffffffff81cd0a59 0000000000000058 ffff88006d404240 ffff88006c86fd48
ffffffff811fa3a8 ffff88006d404240 ffffea0001b52f80 ffff88006d4bed20
Call Trace:
dump_stack (lib/dump_stack.c:52)
print_trailer (mm/slub.c:645)
object_err (mm/slub.c:652)
? sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
kasan_report_error (mm/kasan/report.c:102 mm/kasan/report.c:178)
? kasan_poison_shadow (mm/kasan/kasan.c:48)
? kasan_unpoison_shadow (mm/kasan/kasan.c:54)
? kasan_poison_shadow (mm/kasan/kasan.c:48)
? kasan_kmalloc (mm/kasan/kasan.c:311)
__asan_load4 (mm/kasan/kasan.c:371)
? sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
sched_init_smp (kernel/sched/core.c:6552 kernel/sched/core.c:7063)
kernel_init_freeable (init/main.c:869 init/main.c:997)
? finish_task_switch (kernel/sched/sched.h:1036 kernel/sched/core.c:2248)
? rest_init (init/main.c:924)
kernel_init (init/main.c:929)
? rest_init (init/main.c:924)
ret_from_fork (arch/x86/kernel/entry_64.S:348)
? rest_init (init/main.c:924)
Read of size 4 by task swapper/0:
Memory state around the buggy address:
ffff88006d4beb80: fc fc fc fc fc fc fc fc fc fc 00 fc fc fc fc fc
ffff88006d4bec00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bec80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bed00: fc fc fc fc 00 fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bed80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88006d4bee00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc 04 fc
^
ffff88006d4bee80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bef00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88006d4bef80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff88006d4bf000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff88006d4bf080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Zero 'level' (e.g. on non-NUMA system) causing out of bounds
access in this line:
sched_max_numa_distance = sched_domains_numa_distance[level - 1];
Fix this by exiting from sched_init_numa() earlier.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Fixes: 9942f79ba ("sched/numa: Export info needed for NUMA balancing on complex topologies")
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1415372020-1871-1-git-send-email-a.ryabinin@samsung.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a null pointer dereference issue incurred by
calling g2d_remove when exynos_drm_platform_probe is failed.
cmdlist_pool of g2d is allocated when g2d sub driver is probed.
So if exynos_drm_platform_probe is failed, the g2d sub driver is
not probed and the cmdlist_pool is still NULL.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resovles the infinite loop issue incurred
when Exyno drm driver is enabled but all kms drivers
are disabled on Exynos board by returning -EPROBE_DEFER
only in case that there is kms device registered.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves temporarily infinite loop issue incurred
when Exynos drm driver is enabled and multi-platform kernel
is used by registering Exynos drm device object only in case
of Exynos SoC. So this patch will be replaced with more generic
way later.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Black screen, screen corruption, hardware state corruption fixes.
* tag 'drm-intel-fixes-2014-11-07' of git://anongit.freedesktop.org/drm-intel:
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
If no freeze_ops is set, trying to enter suspend-to-IDLE will cause a
nice oops in platform_suspend_prepare_late(). Add respective checks to
platform_suspend_prepare_late() and platform_resume_early() functions.
Fixes: a8d46b9e4e (ACPI / sleep: Rework the handling of ACPI GPE wakeup ...)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull irq fixes from Thomas Gleixner:
"Two fixlets for the armada SoC interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: armada-370-xp: Fix MPIC interrupt handling
irqchip: armada-370-xp: Fix MSI interrupt handling
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in
14e0e28 dmaengine: sun6i: Remove obsolete clk muxing code
Unfortunately the rest of that series did not make it, leaving us with
broken dma on sun6i.
This patch reparents ahb1_mux to pll6 using the DT assigned-clocks
properties in the dma controller node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Convert the prototypes to return an int in order to support error
handling in these callbacks.
Also, as suggested by Dmitry Torokhov, pass the domain pointer for use
inside the callbacks, and so that they match the existing
power_on/power_off callbacks which currently take the domain pointer.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ khilman: added domain as parameter to callbacks, as suggested by Dmitry ]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When resuming from s2ram on an SMP system without cpufreq operating
points (e.g. there's no "operating-points" property for the CPU node in
DT, or the platform doesn't use DT yet), the kernel crashes when
bringing CPU 1 online:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee5e6b00
[0000003c] *pgd=6e579003, *pmd=6e588003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1246 Comm: s2ram Tainted: G W 3.18.0-rc3-koelsch-01614-g0377af242bb175c8-dirty #589
task: eeec5240 ti: ee704000 task.ti: ee704000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c0298efc>] lr : [<c0298ef4>] psr: 60000153
sp : ee705d48 ip : ee705d48 fp : ee705d84
r10: c04e0450 r9 : 00000000 r8 : 00000001
r7 : c05426a8 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c0542734
Verify that policy is not NULL before dereferencing it to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 8414809c6a (cpufreq: Preserve policy structure across suspend/resume)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Atomicity between xchg and cmpxchg cannot be guaranteed when xchg is
implemented with a swap and cmpxchg is implemented with locks.
Without this, e.g. mcs_spin_lock and mcs_spin_unlock are broken.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3cc81d85ee ("asix: Don't reset PHY on if_up for ASIX 88772")
causes the ethernet on Arndale to no longer function. This appears to
be because the Arndale ethernet requires a full reset before it will
function correctly, however simply reverting the above patch causes
problems with ethtool settings getting reset.
It seems the problem is that the ethernet is not properly reset during
bind, and indeed the code in ax88772_bind that resets the device is a
very small subset of the actual ax88772_reset function. This patch uses
ax88772_reset in place of the existing reset code in ax88772_bind which
removes some code duplication and fixes the ethernet on Arndale.
It is still possible that the original patch causes some issues with
suspend and resume but that seems like a separate issue and I haven't
had a chance to test that yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Cc: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In exynos5260_tmu_registers tmu_ctrl entry is erroneously
assigned twice. The second assignment (to EXYNOS_TMU_REG_CONTROL1
define which represents 0x24 value) overrides the first one
(to EXYNOS_TMU_REG_CONTROL define which represents 0x20 value)
which results in the wrong (according to the Exynos5260 SoC
documentation that I have) offset being used for TMU_CONTROL
register. Fix it by removing the wrong assignment and then
remove no longer used EXYNOS_TMU_REG_CONTROL1 define.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
thermal driver should be regisetered after cpufreq driver has
been registered and probed. Doing so is to make sure that thermal
driver can get the max cpu cooling states correctly when calling
get_property.
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add a i8042 filter to hp_accel to remove accelerometer's data with acpi
id HPQ6000 from keyboard bus stream. The codes sent by accelerometer are
e0 25, e0 26, e0 27 and e0 28. The relevant information is already
passed through /dev/freefall so no need to send these undocumented weird
signals through the keyboard bus. Also, unclogs `dmesg` because atkbd
complained about weird scan codes, saves processing power and disk
space.
Signed-off-by: Giedrius Statkevičius <giedriuswork@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03f), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
-----------------------------------------------------
<4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40()
<4>[ 3965.441474] Hardware name: Romley
<4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)...
...
<4>[ 3965.441605] Call Trace:
<4>[ 3965.441611] [<ffffffff8103717a>] warn_slowpath_common+0x7a/0xb0
<4>[ 3965.441615] [<ffffffff810371c5>] warn_slowpath_null+0x15/0x20
<4>[ 3965.441618] [<ffffffff81215963>] kobject_get+0x33/0x40
<4>[ 3965.441624] [<ffffffff812d1e45>] get_device_parent.isra.11+0x135/0x1f0
<4>[ 3965.441627] [<ffffffff812d22d4>] device_add+0xd4/0x6d0
<4>[ 3965.441631] [<ffffffff812d0dbc>] ? dev_set_name+0x3c/0x40
....
<2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65!
<4>[ 3965.441915] invalid opcode: 0000 [#1] SMP
...
<4>[ 3965.686743] [<ffffffff811a677e>] sysfs_create_group+0xe/0x10
<4>[ 3965.686748] [<ffffffff810cfb04>] blk_trace_init_sysfs+0x14/0x20
<4>[ 3965.686753] [<ffffffff811fcabb>] blk_register_queue+0x3b/0x120
<4>[ 3965.686756] [<ffffffff812030bc>] add_disk+0x1cc/0x490
....
-------------------------------------------------------
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Weng Meiling <wengmeiling.weng@huawei.com>
Cc: <stable@vger.kernel.org> #3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with version 2.24.51.20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
{standard input}: Warning: .gnu_attribute 4,3 requires `softfloat'
LD arch/mips/alchemy/common/built-in.o
mipsel-softfloat-linux-gnu-ld: Warning: arch/mips/alchemy/common/built-in.o
uses -msoft-float (set by arch/mips/alchemy/common/prom.o),
arch/mips/alchemy/common/sleeper.o uses -mhard-float
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
John W. Linville says:
====================
pull request: wireless 2014-11-06
Please pull this batch of fixes intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
For the iwlwifi bits, Emmanuel says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix missing crtc unlock in MC setup
- set optimal CE ram config
- use gart rather than vram for DMA IB tests to avoid coherency issues with HDP
- fix a crasher with laptop mode and TDP scripts
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add missing crtc unlock when setting up the MC
drm/radeon: use gart for DMA IB tests
drm/radeon: make sure mode init is complete in bandwidth_update
drm/radeon: set correct CE ram size for CIK
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen says:
====================
mlx5_core fixes for 3.18
the following two patches fix races to could lead to kernel panic in some cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bulkstat main loop progress is tracked by the "lastino"
variable, which is a full 64 bit inode. However, the loop actually
works on agno/agino pairs, and so there's a significant disconnect
between the rest of the loop and the main cursor. Convert this to
use the agino, and pass the agino into the chunk formatting function
and convert it too.
This gets rid of the inconsistency in the loop processing, and
finally makes it simple for us to skip inodes at any point in the
loop simply by incrementing the agino cursor.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The error propagation is a horror - xfs_bulkstat() returns
a rval variable which is only set if there are formatter errors. Any
sort of btree walk error or corruption will cause the bulkstat walk
to terminate but will not pass an error back to userspace. Worse
is the fact that formatter errors will also be ignored if any inodes
were correctly formatted into the user buffer.
Hence bulkstat can fail badly yet still report success to userspace.
This causes significant issues with xfsdump not dumping everything
in the filesystem yet reporting success. It's not until a restore
fails that there is any indication that the dump was bad and tha
bulkstat failed. This patch now triggers xfsdump to fail with
bulkstat errors rather than silently missing files in the dump.
This now causes bulkstat to fail when the lastino cookie does not
fall inside an existing inode chunk. The pre-3.17 code tolerated
that error by allowing the code to move to the next inode chunk
as the agino target is guaranteed to fall into the next btree
record.
With the fixes up to this point in the series, xfsdump now passes on
the troublesome filesystem image that exposes all these bugs.
cc: <stable@vger.kernel.org>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There are a bunch of variables tha tare more wildy scoped than they
need to be, obfuscated user buffer checks and tortured "next inode"
tracking. This all needs cleaning up to expose the real issues that
need fixing.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The loop construct has issues:
- clustidx is completely unused, so remove it.
- the loop tries to be smart by terminating when the
"freecount" tells it that all inodes are free. Just drop
it as in most cases we have to scan all inodes in the
chunk anyway.
- move the "user buffer left" condition check to the only
point where we consume space int eh user buffer.
- move the initialisation of agino out of the loop, leaving
just a simple loop control logic using the clusteridx.
Also, double handling of the user buffer variables leads to problems
tracking the current state - use the cursor variables directly
rather than keeping local copies and then having to update the
cursor before returning.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The xfs_bulkstat_agichunk formatting cursor takes buffer values from
the main loop and passes them via the structure to the chunk
formatter, and the writes the changed values back into the main loop
local variables. Unfortunately, this complex dance is full of corner
cases that aren't handled correctly.
The biggest problem is that it is double handling the information in
both the main loop and the chunk formatting function, leading to
inconsistent updates and endless loops where progress is not made.
To fix this, push the struct xfs_bulkstat_agichunk outwards to be
the primary holder of user buffer information. this removes the
double handling in the main loop.
Also, pass the last inode processed by the chunk formatter as a
separate parameter as it purely an output variable and is not
related to the user buffer consumption cursor.
Finally, the chunk formatting code is not shared by anyone, so make
it local to xfs_itable.c.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The bulkstat code has several different ways of detecting the end of
an AG when doing a walk. They are not consistently detected, and the
code that checks for the end of AG conditions is not consistently
coded. Hence the are conditions where the walk code can get stuck in
an endless loop making no progress and not triggering any
termination conditions.
Convert all the "tmp/i" status return codes from btree operations
to a common name (stat) and apply end-of-ag detection to these
operations consistently.
cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
XFS doesn't always hold i_mutex when calling truncate_setsize() and it
uses a different lock to serialize truncates and writes. So fix the
comment before truncate_setsize().
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Use gart rather than vram to avoid having to deal with
the HDP cache.
Port of adfed2b058
(drm/radeon: use gart memory for DMA ring tests)
to the IB tests.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The power management code calls into the display code for
certain things. If certain power management sysfs attributes
are called before the driver has finished initializing all of
the hardware we can run into problems with uninitialized
modesetting state. Add a check to make sure modesetting
init has completed to the bandwidth update callbacks to
fix this. Can be triggered by the tlp and laptop start
up scripts depending on the timing.
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=83611https://bugs.freedesktop.org/show_bug.cgi?id=85771
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Add new quirk for devices that cannot handle control-line state
requests.
Note that we currently send these requests to all devices, regardless of
whether they claim to support it, but that errors are only logged if
support is claimed.
Since commit 0943d8ead3 ("USB: cdc-acm: use tty-port dtr_rts"), which
only changed the timings for these requests slightly, this has been
reported to cause occasional firmware crashes on Simtec Electronics
Entropy Key devices after re-enumeration. Enable the quirk for this
device.
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Cc: stable <stable@vger.kernel.org> # v3.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
usb: fixes for v3.18-rc4
A single fix this for dwc2 this time. Because of
excessive debugging messages, dwc2 would sometimes
fail enumeration. The fix is simple, just converting
a dev_info() into dev_dbg().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit f95499c303 ("n_tty: Don't wait for buffer work in read() loop")
introduces a race window where a pty master can be signalled that the pty
slave was closed before all the data that the slave wrote is delivered.
Commit f8747d4a46 ("tty: Fix pty master read() after slave closes") fixed the
problem in case of n_tty_read, but the problem still exists for n_tty_poll.
This can be seen by running 'for ((i=0; i<100;i++));do ./test.py ;done'
where test.py is:
import os, select, pty
(pid, pty_fd) = pty.fork()
if pid == 0:
os.write(1, 'This string should be received by parent')
else:
poller = select.epoll()
poller.register( pty_fd, select.EPOLLIN )
ready = poller.poll( 1 * 1000 )
for fd, events in ready:
if not events & select.EPOLLIN:
print 'missed POLLIN event'
else:
print os.read(fd, 100)
poller.close()
The string from the slave is missed several times.
This patch takes the same approach as the fix for read and special cases
this condition for poll.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull PCI fix from Bjorn Helgaas:
"This fixes an oops when enabling SR-IOV VF devices. The oops is a
regression I added by configuring all devices during enumeration.
- Don't oops on virtual buses in acpi_pci_get_bridge_handle() (Yinghai Lu)"
* tag 'pci-v3.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't oops on virtual buses in acpi_pci_get_bridge_handle()
Pull sound fixes from Takashi Iwai:
"This update contains mostly only fixes for Realtek HD-audio codec
driver in addition to a long-standing sysfs warning bug fix for
USB-audio.
One significant fix for Realtek codecs is the update of EAPD init
codes. This avoids invalid COEF setups for some codec models and may
fix "lost sound" in some cases.
The rest are a bit high volume but only new quirks and ALC668-specific
COEF tables"
* tag 'sound-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Restore default value for ALC668
ALSA: usb-audio: Fix device_del() sysfs warnings at disconnect
ALSA: hda - fix mute led problem for three HP laptops
ALSA: hda/realtek - Update Initial AMP for EAPD control
ALSA: hda - change three SSID quirks to one pin quirk
ALSA: hda - Set GPIO 4 low for a few HP machines
ALSA: hda - Add ultra dock support for Thinkpad X240.
Pull MMC fix from Ulf Hansson:
"Fix card detection regression in the MMC core.
The MMC_CAP2_CD_ACTIVE_HIGH and MMC_CAP2_RO_ACTIVE_HIGH could under
some circumstances be set incorrectly, causing the card detection to
fail"
* tag 'mmc-v3.18-2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix card detection regression
Pull another filesystem fix from Al Viro:
"A fix for embarrassing braino in o2net_send_tcp_msg(). -stable
fodder..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix breakage in o2net_send_tcp_msg()
https://bugzilla.kernel.org/show_bug.cgi?id=86831
Markus reported that when shutting down mysqld (with AIO support,
on a ext3 formatted Harddrive) leads to a negative number of dirty pages
(underrun to the counter). The negative number results in a drastic reduction
of the write performance because the page cache is not used, because the kernel
thinks it is still 2 ^ 32 dirty pages open.
Add a warn trace in __dec_zone_state will catch this easily:
static inline void __dec_zone_state(struct zone *zone, enum
zone_stat_item item)
{
atomic_long_dec(&zone->vm_stat[item]);
+ WARN_ON_ONCE(item == NR_FILE_DIRTY &&
atomic_long_read(&zone->vm_stat[item]) < 0);
atomic_long_dec(&vm_stat[item]);
}
[ 21.341632] ------------[ cut here ]------------
[ 21.346294] WARNING: CPU: 0 PID: 309 at include/linux/vmstat.h:242
cancel_dirty_page+0x164/0x224()
[ 21.355296] Modules linked in: wutbox_cp sata_mv
[ 21.359968] CPU: 0 PID: 309 Comm: kworker/0:1 Not tainted 3.14.21-WuT #80
[ 21.366793] Workqueue: events free_ioctx
[ 21.370760] [<c0016a64>] (unwind_backtrace) from [<c0012f88>]
(show_stack+0x20/0x24)
[ 21.378562] [<c0012f88>] (show_stack) from [<c03f8ccc>]
(dump_stack+0x24/0x28)
[ 21.385840] [<c03f8ccc>] (dump_stack) from [<c0023ae4>]
(warn_slowpath_common+0x84/0x9c)
[ 21.393976] [<c0023ae4>] (warn_slowpath_common) from [<c0023bb8>]
(warn_slowpath_null+0x2c/0x34)
[ 21.402800] [<c0023bb8>] (warn_slowpath_null) from [<c00c0688>]
(cancel_dirty_page+0x164/0x224)
[ 21.411524] [<c00c0688>] (cancel_dirty_page) from [<c00c080c>]
(truncate_inode_page+0x8c/0x158)
[ 21.420272] [<c00c080c>] (truncate_inode_page) from [<c00c0a94>]
(truncate_inode_pages_range+0x11c/0x53c)
[ 21.429890] [<c00c0a94>] (truncate_inode_pages_range) from
[<c00c0f6c>] (truncate_pagecache+0x88/0xac)
[ 21.439252] [<c00c0f6c>] (truncate_pagecache) from [<c00c0fec>]
(truncate_setsize+0x5c/0x74)
[ 21.447731] [<c00c0fec>] (truncate_setsize) from [<c013b3a8>]
(put_aio_ring_file.isra.14+0x34/0x90)
[ 21.456826] [<c013b3a8>] (put_aio_ring_file.isra.14) from
[<c013b424>] (aio_free_ring+0x20/0xcc)
[ 21.465660] [<c013b424>] (aio_free_ring) from [<c013b4f4>]
(free_ioctx+0x24/0x44)
[ 21.473190] [<c013b4f4>] (free_ioctx) from [<c003d8d8>]
(process_one_work+0x134/0x47c)
[ 21.481132] [<c003d8d8>] (process_one_work) from [<c003e988>]
(worker_thread+0x130/0x414)
[ 21.489350] [<c003e988>] (worker_thread) from [<c00448ac>]
(kthread+0xd4/0xec)
[ 21.496621] [<c00448ac>] (kthread) from [<c000ec18>]
(ret_from_fork+0x14/0x20)
[ 21.503884] ---[ end trace 79c4bf42c038c9a1 ]---
The cause is that we set the aio ring file pages as *DIRTY* via SetPageDirty
(bypasses the VFS dirty pages increment) when init, and aio fs uses
*default_backing_dev_info* as the backing dev, which does not disable
the dirty pages accounting capability.
So truncating aio ring file will contribute to accounting dirty pages (VFS
dirty pages decrement), then error occurs.
The original goal is keeping these pages in memory (can not be reclaimed
or swapped) in life-time via marking it dirty. But thinking more, we have
already pinned pages via elevating the page's refcount, which can already
achieve the goal, so the SetPageDirty seems unnecessary.
In order to fix the issue, using the __set_page_dirty_no_writeback instead
of the nop .set_page_dirty, and dropped the SetPageDirty (don't manually
set the dirty flags, don't disable set_page_dirty(), rely on default behaviour).
With the above change, the dirty pages accounting can work well. But as we
known, aio fs is an anonymous one, which should never cause any real write-back,
we can ignore the dirty pages (write back) accounting by disabling the dirty
pages (write back) accounting capability. So we introduce an aio private
backing dev info (disabled the ACCT_DIRTY/WRITEBACK/ACCT_WB capabilities) to
replace the default one.
Reported-by: Markus Königshaus <m.koenigshaus@wut.de>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
The 5th NAND partition should be named "NAND.u-boot-spl-os"
instead of "NAND.u-boot-spl". This is to be consistent with other
TI boards as well as u-boot.
Fixes: 91994facdd ("ARM: dts: am335x-evm: NAND: update MTD partition table")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Never trust (your interpretation of) the VBT. Regression from
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
causing div by zero if VBT minimum brightness equals maximum brightness.
Despite my attempts I've failed in my detective work to figure out what
the root cause is. This is not the real fix, but we have to do
something.
Reported-by: Mike Auty <mike.auty@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=86551
Cc: stable@vger.kernel.org (v3.17+)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During S4 freeze we don't call intel_suspend_complete(), which would
save the gunit HW state, but during S4 thaw/restore events we call
intel_resume_prepare() which restores it, thus ending up in a corrupted
HW state.
Fix this by calling intel_suspend_complete() from the corresponding
freeze_late event handler.
The issue was introduced in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Global GTT doesn't have pat_sel[2:0] so it always point to pat_sel = 000;
So the only way to avoid screen corruptions is setting PAT 0 to Uncached.
MOCS can still be used though. But if userspace is trusting PTE for
cache selection the safest thing to do is to let caches disabled.
BSpec: "For GGTT, there is NO pat_sel[2:0] from the entry,
so RTL will always use the value corresponding to pat_sel = 000"
- System agent ggtt writes (i.e. cpu gtt mmaps) already work before
this patch, i.e. the same uncached + snooping access like on gen6/7
seems to be in effect.
- So this just fixes blitter/render access. Again it looks like it's
not just uncached access, but uncached + snooping. So we can still
hold onto all our assumptions wrt cpu clflushing on LLC machines.
v2: Cleaner patch as suggested by Chris.
v3: Add Daniel's comment
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85576
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Stable@vger.kernel.org
Tested-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The add_early_randomness() function in drivers/char/hw_random/core.c passes
a 16-byte buffer to pseries_rng_data_read(). Unfortunately, plpar_hcall()
returns four 64-bit values and trashes 16 bytes on the stack.
This bug has been lying around for a long time. It got unveiled by:
commit d3cc799647
Author: Amit Shah <amit.shah@redhat.com>
Date: Thu Jul 10 15:42:34 2014 +0530
hwrng: fetch randomness only after device init
It may trig a oops while loading or unloading the pseries-rng module for both
PowerVM and PowerKVM guests.
This patch does two things:
- pass an intermediate well sized buffer to plpar_hcall(). This is acceptalbe
since we're not on a hot path.
- move to the new read API so that we know the return buffer size for sure.
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If dma mapping for dma_addr_out fails, the descriptor memory is freed
but the previous dma mapping for dma_addr_in remains.
This patch resolves the missing dma unmap and groups resource
allocations at function start.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a50585 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit 7ec7c4a9a6 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:
(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)
Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.
This patch adds an additional length check.
Cc: stable@vger.kernel.org
Fixes: 7ec7c4a9a6 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PLL should be powered up once filter power is on. So, "PLL1"
should be connected to filters instead of DACs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The info pointer points to an uninitialized kmalloced space.
If a device doesn't have clk property, then info->clk may
have unpredicated value and cause call trace. So use kzalloc
to make sure it is NULL initialized.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The calculation of value quot for highspeed register set to three
was wrong. This patch fixes the calculation so that the serial port
for baudrates bigger then 576000 baud is working correctly.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The horrible split between the low-level part of the edma support
and the dmaengine front-end driver causes problems on multiplatform
kernels. This is an attempt to improve the situation slightly
by only registering the dmaengine devices that are actually
present.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: add missing include of linux/dma-mapping.h]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Kernel oops can cause the tty to be unreleaseable (for example, if
n_tty_read() crashes while on the read_wait queue). This will cause
tty_release() to endlessly loop without sleeping.
Use a killable sleep timeout which grows by 2n+1 jiffies over the interval
[0, 120 secs.) and then jumps to forever (but still killable).
NB: killable just allows for the task to be rewoken manually, not
to be terminated.
Cc: <stable@vger.kernel.org> # since before 2.6.32
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_get_baud_rate() will return baud == 0 if the max rate is set
to the "magic" 38400 rate and the SPD_* flags are also specified.
On the first iteration, if the current baud rate is higher than the
max, the baud rate is clamped at the max (which in the degenerate
case is 38400). On the second iteration, the now-"magic" 38400 baud
rate selects the possibly higher alternate baud rate indicated by
the SPD_* flag. Since only two loop iterations are performed, the
loop is exited, a kernel WARNING is generated and a baud rate of
0 is returned.
Reproducible with:
setserial /dev/ttyS0 spd_hi base_baud 38400
Only perform the "magic" 38400 -> SPD_* baud transform on the first
loop iteration, which prevents the degenerate case from recognizing
the clamped baud rate as the "magic" 38400 value.
Reported-by: Robert Święcki <robert@swiecki.net>
Cc: <stable@vger.kernel.org> # all
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB OTG port does not work since v3.16 on omap platform.
This is a regression introduced by the commit
eb82a3d846 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure
and remove).
This because the call to pm_runtime_enable() function is moved after the
call to devm_phy_create() function, which has side effect since later in
the subsequent calls of devm_phy_create() there is a check with
pm_runtime_enabled() to configure few things.
Fixes: eb82a3d846
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if_bridge.h uses struct in6_addr ip6, but wasn't including the in6.h
header. Thomas Backlund originally sent a patch to do this, but this
revealed a redefinition issue: https://lkml.org/lkml/2013/1/13/116
The redefinition issue should have been fixed by the following Linux
commits:
ee262ad827 inet: defines IPPROTO_* needed for module alias generation
cfd280c912 net: sync some IP headers with glibc
and the following glibc commit:
6c82a2f8d7c8e21e39237225c819f182ae438db3 Coordinate IPv6 definitions for Linux and glibc
so actually include the header now.
Reported-by: Colin Guthrie <colin@mageia.org>
Reported-by: Christiaan Welvaart <cjw@daneel.dyndns.org>
Reported-by: Thomas Backlund <tmb@mageia.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ueki Kohei reported that when we are using NewReno with connections that
have a very low traffic, we may timeout the connection too early if a
second loss occurs after the first one was successfully acked but no
data was transfered later. Below is his description of it:
When SACK is disabled, and a socket suffers multiple separate TCP
retransmissions, that socket's ETIMEDOUT value is calculated from the
time of the *first* retransmission instead of the *latest*
retransmission.
This happens because the tcp_sock's retrans_stamp is set once then never
cleared.
Take the following connection:
Linux remote-machine
| |
send#1---->(*1)|--------> data#1 --------->|
| | |
RTO : :
| | |
---(*2)|----> data#1(retrans) ---->|
| (*3)|<---------- ACK <----------|
| | |
| : :
| : :
| : :
16 minutes (or more) :
| : :
| : :
| : :
| | |
send#2---->(*4)|--------> data#2 --------->|
| | |
RTO : :
| | |
---(*5)|----> data#2(retrans) ---->|
| | |
| | |
RTO*2 : :
| | |
| | |
ETIMEDOUT<----(*6)| |
(*1) One data packet sent.
(*2) Because no ACK packet is received, the packet is retransmitted.
(*3) The ACK packet is received. The transmitted packet is acknowledged.
At this point the first "retransmission event" has passed and been
recovered from. Any future retransmission is a completely new "event".
(*4) After 16 minutes (to correspond with retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and (*4).
The socket's timeout SHOULD be calculated from this point in time, but
instead it's calculated from the prior "event" 16 minutes ago.
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT.
Therefore, now we clear retrans_stamp as soon as all data during the
loss window is fully acked.
Reported-by: Ueki Kohei
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe Cavallaro says:
====================
stmmac: review and fix lock and atomicity
Recently some issues have been reported for the driver for locking mechanism
and atomicity.
In fact, enabling DEBUG support to prove lock and to verify if sleeping while
atomic context some warnings occur at runtime. I have reproduced all on STi
platforms.
Concerning the tx path, I had provided a patch time ago but
I discarded the idea to completely remove locks; in this patch-set we can have
some useful fixes instead of.
This patch-set is to fix the atomicity in the PM stuff where I tried to collect
all the points and advice reported in the past weeks.
As final result, on my side no warnings and no problem when suspend/resume the
driver on STi boxes.
I also added a patch that fixes the locks for the EEE.
As pointed in some thread there was a design problem behind the eee
initialization and I have tried to fix that before.
As final result no issues when proving locks too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.
So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).
The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was initially sent by Lorenzo Colitti, but was subsequently
lost in the final diff he submitted.
Signed-off-by: Loganaden Velvindron <logan@elandsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"One small improvement for the cputime accounting, two bug fixes and an
update for the default configuration files"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ftrace: add ftrace_graph_is_dead() check
s390: update default configuration
s390/vdso: fix stack corruption
s390/time: use stck clock fast for do_account_vtime
acpi_pci_get_bridge_handle() returns the ACPI handle for the bridge device
(either a host bridge or a PCI-to-PCI bridge) leading to a PCI bus. But
SR-IOV virtual functions can be on a virtual bus with no bridge leading to
it. Return a NULL acpi_handle in this case instead of trying to
dereference the NULL pointer to the bridge.
This fixes a NULL pointer dereference oops in pci_get_hp_params() when
adding SR-IOV VF devices on virtual buses.
[bhelgaas: changelog, add comment in code]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=87591
Reported-by: Chao Zhou <chao.zhou@intel.com>
Reported-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pernet ops aren't ever unregistered, which causes a memory
leak and an OOPs if the module is ever reinserted.
Fixes: 0b5e8b8eea ("net: Add Geneve tunneling protocol driver")
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geneve does not currently set the inner protocol type when
transmitting packets. This causes GSO segmentation to fail on NICs
that do not support Geneve offloading.
CC: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
Second round of IIO fixes for the 3.18 cycle.
* tsl4531 - fix a compile error when CONFIG_PM_OPS not set.
* kxcjk-1013 - event spec direction was invalid - leading to 'interesting'
attrribute names.
* as3935 - sizeof(st) used instead of sizeof(*st) leading to allocation of
space for a pointer rather than the structure desired.
* ade7758 - Another null pointer deref fix due to different channels
being provided to the the buffer register than used for the sysfs
side of things.
* ade7758 - Check there is a channel enabled in preenable for the buffer
before doing anything.
* ade7758 - Drop a stray raw from the channel name that leads to _raw_raw
postfix.
Make sure to only raise DTR on transitions from B0 in set_termios.
Also allow set_termios to be called from open with a termios_old of
NULL. Note that DTR will not be raised prematurely in this case.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver has been there since a while back, but the dts never seems to
have been updated with the node (nor pinctrl). Do so now.
Cc: Matt Porter <mporter@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
"raw" is a property of a channel, but should not be part of the name of
channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We should check if a channel is enabled, not if no channels are enabled.
Fixes: 550268ca11 ("staging:iio: scrap scan_count and ensure all drivers use active_scan_mask")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In older versions of the IIO framework it was possible to pass a completely
different set of channels to iio_buffer_register() as the one that is
assigned to the IIO device. Commit 959d2952d1 ("staging:iio: make
iio_sw_buffer_preenable much more general.") introduced a restriction that
requires that the set of channels that is passed to iio_buffer_register() is
a subset of the channels assigned to the IIO device as the IIO core will use
the list of channels that is assigned to the device to lookup a channel by
scan index in iio_compute_scan_bytes(). If it can not find the channel the
function will crash. This patch fixes the issue by making sure that the same
set of channels is assigned to the IIO device and passed to
iio_buffer_register().
Note that we need to remove the IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE
info attributes from the channels since we don't actually want those to be
registered.
Fixes the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000016
pgd = d2094000
[00000016] *pgd=16e39831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 1695 Comm: bash Not tainted 3.17.0-06329-g29461ee #9686
task: d7768040 ti: d5bd4000 task.ti: d5bd4000
PC is at iio_compute_scan_bytes+0x38/0xc0
LR is at iio_compute_scan_bytes+0x34/0xc0
pc : [<c0316de8>] lr : [<c0316de4>] psr: 60070013
sp : d5bd5ec0 ip : 00000000 fp : 00000000
r10: d769f934 r9 : 00000000 r8 : 00000001
r7 : 00000000 r6 : c8fc6240 r5 : d769f800 r4 : 00000000
r3 : d769f800 r2 : 00000000 r1 : ffffffff r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 18c5387d Table: 1209404a DAC: 00000015
Process bash (pid: 1695, stack limit = 0xd5bd4240)
Stack: (0xd5bd5ec0 to 0xd5bd6000)
5ec0: d769f800 d7435640 c8fc6240 d769f984 00000000 c03175a4 d7435690 d7435640
5ee0: d769f990 00000002 00000000 d769f800 d5bd4000 00000000 000b43a8 c03177f4
5f00: d769f810 0162b8c8 00000002 c8fc7e00 d77f1d08 d77f1da8 c8fc7e00 c01faf1c
5f20: 00000002 c010694c c010690c d5bd5f88 00000002 c8fc6840 c8fc684c c0105e08
5f40: 00000000 00000000 d20d1580 00000002 000af408 d5bd5f88 c000de84 c00b76d4
5f60: d20d1580 000af408 00000002 d20d1580 d20d1580 00000002 000af408 c000de84
5f80: 00000000 c00b7a44 00000000 00000000 00000002 b6ebea78 00000002 000af408
5fa0: 00000004 c000dd00 b6ebea78 00000002 00000001 000af408 00000002 00000000
5fc0: b6ebea78 00000002 000af408 00000004 bee96a4c 000a6094 00000000 000b43a8
5fe0: 00000000 bee969cc b6e2eb77 b6e6525c 40070010 00000001 00000000 00000000
[<c0316de8>] (iio_compute_scan_bytes) from [<c03175a4>] (__iio_update_buffers+0x248/0x438)
[<c03175a4>] (__iio_update_buffers) from [<c03177f4>] (iio_buffer_store_enable+0x60/0x7c)
[<c03177f4>] (iio_buffer_store_enable) from [<c01faf1c>] (dev_attr_store+0x18/0x24)
[<c01faf1c>] (dev_attr_store) from [<c010694c>] (sysfs_kf_write+0x40/0x4c)
[<c010694c>] (sysfs_kf_write) from [<c0105e08>] (kernfs_fop_write+0x110/0x154)
[<c0105e08>] (kernfs_fop_write) from [<c00b76d4>] (vfs_write+0xbc/0x170)
[<c00b76d4>] (vfs_write) from [<c00b7a44>] (SyS_write+0x40/0x78)
[<c00b7a44>] (SyS_write) from [<c000dd00>] (ret_fast_syscall+0x0/0x30)
Fixes: 959d2952d1 ("staging:iio: make iio_sw_buffer_preenable much more general.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Because IIO_EV_DIR_* are not bitmasks but enums,
IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING is not equal
with IIO_EV_DIR_EITHER.
This could lead to potential misformatted sysfs attributes
like:
* in_accel_x_thresh_(null)_en
* in_accel_x_thresh_(null)_period
* in_accel_x_thresh_(null)_value
or even memory corruption.
Fixes: b4b491c083 (iio: accel: kxcjk-1013: Support threshold)
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix the compiler error when the CONFIG_PM_OPS flag is not set.
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_suspend’ undeclared here (not in a function)
drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_resume’ undeclared here (not in a function)
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
"raw" is the name of a channel property, but should not be part of the
channel name itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In older versions of the IIO framework it was possible to pass a
completely different set of channels to iio_buffer_register() as the one
that is assigned to the IIO device. Commit 959d2952d1 ("staging:iio: make
iio_sw_buffer_preenable much more general.") introduced a restriction that
requires that the set of channels that is passed to iio_buffer_register() is
a subset of the channels assigned to the IIO device as the IIO core will use
the list of channels that is assigned to the device to lookup a channel by
scan index in iio_compute_scan_bytes(). If it can not find the channel the
function will crash. This patch fixes the issue by making sure that the same
set of channels is assigned to the IIO device and passed to
iio_buffer_register().
Fixes the follow NULL pointer derefernce kernel crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000016
pgd = d53d0000
[00000016] *pgd=1534e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 1626 Comm: bash Not tainted 3.15.0-19969-g2a180eb-dirty #9545
task: d6c124c0 ti: d539a000 task.ti: d539a000
PC is at iio_compute_scan_bytes+0x34/0xa8
LR is at iio_compute_scan_bytes+0x34/0xa8
pc : [<c03052e4>] lr : [<c03052e4>] psr: 60070013
sp : d539beb8 ip : 00000001 fp : 00000000
r10: 00000002 r9 : 00000000 r8 : 00000001
r7 : 00000000 r6 : d6dc8800 r5 : d7571000 r4 : 00000002
r3 : d7571000 r2 : 00000044 r1 : 00000001 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 18c5387d Table: 153d004a DAC: 00000015
Process bash (pid: 1626, stack limit = 0xd539a240)
Stack: (0xd539beb8 to 0xd539c000)
bea0: c02fc0e4 d7571000
bec0: d76c1640 d6dc8800 d757117c 00000000 d757112c c0305b04 d76c1690 d76c1640
bee0: d7571188 00000002 00000000 d7571000 d539a000 00000000 000dd1c8 c0305d54
bf00: d7571010 0160b868 00000002 c69d3900 d7573278 d7573308 c69d3900 c01ece90
bf20: 00000002 c0103fac c0103f6c d539bf88 00000002 c69d3b00 c69d3b0c c0103468
bf40: 00000000 00000000 d7694a00 00000002 000af408 d539bf88 c000dd84 c00b2f94
bf60: d7694a00 000af408 00000002 d7694a00 d7694a00 00000002 000af408 c000dd84
bf80: 00000000 c00b32d0 00000000 00000000 00000002 b6f1aa78 00000002 000af408
bfa0: 00000004 c000dc00 b6f1aa78 00000002 00000001 000af408 00000002 00000000
bfc0: b6f1aa78 00000002 000af408 00000004 be806a4c 000a6094 00000000 000dd1c8
bfe0: 00000000 be8069cc b6e8ab77 b6ec125c 40070010 00000001 22940489 154a5007
[<c03052e4>] (iio_compute_scan_bytes) from [<c0305b04>] (__iio_update_buffers+0x248/0x438)
[<c0305b04>] (__iio_update_buffers) from [<c0305d54>] (iio_buffer_store_enable+0x60/0x7c)
[<c0305d54>] (iio_buffer_store_enable) from [<c01ece90>] (dev_attr_store+0x18/0x24)
[<c01ece90>] (dev_attr_store) from [<c0103fac>] (sysfs_kf_write+0x40/0x4c)
[<c0103fac>] (sysfs_kf_write) from [<c0103468>] (kernfs_fop_write+0x110/0x154)
[<c0103468>] (kernfs_fop_write) from [<c00b2f94>] (vfs_write+0xd0/0x160)
[<c00b2f94>] (vfs_write) from [<c00b32d0>] (SyS_write+0x40/0x78)
[<c00b32d0>] (SyS_write) from [<c000dc00>] (ret_fast_syscall+0x0/0x30)
Code: ea00000e e1a01008 e1a00005 ebfff6fc (e5d0a016)
Fixes: 959d2952d1 ("staging:iio: make iio_sw_buffer_preenable much more general.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch enables a few things missing from our defconfig:
- PCI and MSI, including support for the x-gene host controller
- BPF JIT
- SPI, GPIO and MMC for Seattle
- GPIO for x-gene
- USB for Juno
- RTC
It also removes HMC_DRV, which was being built as a module for some
reason.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We should be accessing it through a pointer, like on the BSP.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 65cef1311d ("x86, microcode: Add a disable chicken bit")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Borislav Petkov <bp@suse.de>
Following the arm32 commit 2d605a3029 (ARM: enable bpf syscall), wire
this syscall for arm64 compat as well.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some USB-audio devices show weird sysfs warnings at disconnecting the
devices, e.g.
usb 1-3: USB disconnect, device number 3
------------[ cut here ]------------
WARNING: CPU: 0 PID: 973 at fs/sysfs/group.c:216 device_del+0x39/0x180()
sysfs group ffffffff8183df40 not found for kobject 'midiC1D0'
Call Trace:
[<ffffffff814a3e38>] ? dump_stack+0x49/0x71
[<ffffffff8103cb72>] ? warn_slowpath_common+0x82/0xb0
[<ffffffff8103cc55>] ? warn_slowpath_fmt+0x45/0x50
[<ffffffff813521e9>] ? device_del+0x39/0x180
[<ffffffff81352339>] ? device_unregister+0x9/0x20
[<ffffffff81352384>] ? device_destroy+0x34/0x40
[<ffffffffa00ba29f>] ? snd_unregister_device+0x7f/0xd0 [snd]
[<ffffffffa025124e>] ? snd_rawmidi_dev_disconnect+0xce/0x100 [snd_rawmidi]
[<ffffffffa00c0192>] ? snd_device_disconnect+0x62/0x90 [snd]
[<ffffffffa00c025c>] ? snd_device_disconnect_all+0x3c/0x60 [snd]
[<ffffffffa00bb574>] ? snd_card_disconnect+0x124/0x1a0 [snd]
[<ffffffffa02e54e8>] ? usb_audio_disconnect+0x88/0x1c0 [snd_usb_audio]
[<ffffffffa015260e>] ? usb_unbind_interface+0x5e/0x1b0 [usbcore]
[<ffffffff813553e9>] ? __device_release_driver+0x79/0xf0
[<ffffffff81355485>] ? device_release_driver+0x25/0x40
[<ffffffff81354e11>] ? bus_remove_device+0xf1/0x130
[<ffffffff813522b9>] ? device_del+0x109/0x180
[<ffffffffa01501d5>] ? usb_disable_device+0x95/0x1f0 [usbcore]
[<ffffffffa014634f>] ? usb_disconnect+0x8f/0x190 [usbcore]
[<ffffffffa0149179>] ? hub_thread+0x539/0x13a0 [usbcore]
[<ffffffff810669f5>] ? sched_clock_local+0x15/0x80
[<ffffffff81066c98>] ? sched_clock_cpu+0xb8/0xd0
[<ffffffff81070730>] ? bit_waitqueue+0xb0/0xb0
[<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore]
[<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore]
[<ffffffff8105973e>] ? kthread+0xce/0xf0
[<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0
[<ffffffff814a8b7c>] ? ret_from_fork+0x7c/0xb0
[<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0
---[ end trace 40b1928d1136b91e ]---
This comes from the fact that usb-audio driver may receive the
disconnect callback multiple times, per each usb interface. When a
device has both audio and midi interfaces, it gets called twice, and
currently the driver tries to release resources at the last call.
At this point, the first parent interface has been already deleted,
thus deleting a child of the first parent hits such a warning.
For fixing this problem, we need to call snd_card_disconnect() and
cancel pending operations at the very first disconnect while the
release of the whole objects waits until the last disconnect call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931
Reported-and-tested-by: Tomas Gayoso <tgayoso@gmail.com>
Reported-and-tested-by: Chris J Arges <chris.j.arges@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ovl_cache_put() can be called from ovl_dir_reset() if the cache needs to be
rebuilt. We did list_del() on the cursor, which results in an Oops on the
poisoned pointer in ovl_seek_cursor().
Reported-by: Jordi Pujol Palomer <jordipujolp@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Jordi Pujol Palomer <jordipujolp@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The emulator could reuse an op->type from a previous instruction for some
immediate values. If it mistakenly considers the operands as memory
operands, it will performs a memory read and overwrite op->val.
Consider for instance the ROR instruction - src2 (the number of times)
would be read from memory instead of being used as immediate.
Mark every immediate operand as such to avoid this problem.
Cc: stable@vger.kernel.org
Fixes: c44b4c6ab8
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without the fix, the mute led can't work on these three machines.
After apply this fix, these three machines will fall back on the led
control quirk as below, and through testing, the mute led works very
well.
PIN_QUIRK(0x10ec0282, 0x103c, "HP", ALC269_FIXUP_HP_LINE1_MIC1_LED,
ALC282_STANDARD_PINS,
{0x12, 0x90a60140},
...
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add Lee Jones as a new co-maintainer.
The kernel.org repo moved to allow us both to push to it. Update
MAINTAINERS to match.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.18, 2nd round" from Shawn Guo:
"This is the second round of i.MX fixes for 3.18. The clk-vf610 fix is
relatively big, because it needs some adaption to the change made by
offending commit dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits
from clk-pllv3 driver). And it should have been sent to you for earlier
-rc inclusion, but unfortunately it got delayed for some time because
Stefan wasn't aware of my email address change."
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
* tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (460 commits)
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
+ Linux 3.18-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
If the OPEN rpc call to the server fails with an ENOENT call, nfs_atomic_open
will create a negative dentry for that file, however it currently fails
to call nfs_set_verifier(), thus causing the dentry to be immediately
revalidated on the next call to nfs_lookup_revalidate() instead of following
the usual lookup caching rules.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Thermal hysteresis represents a temperature difference.
But the original code treats it as a temperature value,
Convert it from tenths of degree Kelvin to Milli-Celsius
by deducing 273200. This is not right.
Kelvin and Celsius have same degree size. From temperature
difference view, the conversion between tenths of degree
Kelvin unit and Milli-Celsius unit is just to multiply 100.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Iyappan Subramanian says:
====================
drivers: net: xgene: Fix crash for backward compatibility
This patch set fixes the following issues that were reported during regression.
Patch 1,2 : Adds backward compatibility with the older firmware (<= 1.13.28).
Patch 3 : Use separate hardware resources (descriptor ring, prefetch buffer)
that are not shared with the firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following kernel crash during SGMII based 1GbE probe.
BUG: Bad page state in process swapper/0 pfn:40fe6ad
page:ffffffbee37a75d8 count:-1 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: nonzero _count
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7
Call trace:
[<ffffffc000087fa0>] dump_backtrace+0x0/0x12c
[<ffffffc0000880dc>] show_stack+0x10/0x1c
[<ffffffc0004d981c>] dump_stack+0x74/0xc4
[<ffffffc00012fe70>] bad_page+0xd8/0x128
[<ffffffc000133000>] get_page_from_freelist+0x4b8/0x640
[<ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834
[<ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8
[<ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c
[<ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280
[<ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340
[<ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50
[<ffffffc00042b454>] net_rx_action+0xc8/0x18c
[<ffffffc0000b0880>] __do_softirq+0x114/0x24c
[<ffffffc0000b0c34>] irq_exit+0x94/0xc8
[<ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4
[<ffffffc000081288>] gic_handle_irq+0x30/0x7c
This was due to hardware resource sharing conflict with the firmware. This
patch fixes this crash by using resources (descriptor ring, prefetch buffer)
that are not shared.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support when used with older firmware (<= 1.13.28).
- Added xgene_ring_mgr_init() to check whether ring manager is initialized
- Calling xgene_ring_mgr_init() from xgene_port_ops.reset()
- To handle errors, changed the return type of xgene_port_ops.reset()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
q->mq_usage_counter is a percpu_ref which is killed and drained when
the queue is frozen. On a CPU hotplug event, blk_mq_queue_reinit()
which involves freezing the queue is invoked on all existing queues.
Because percpu_ref killing and draining involve a RCU grace period,
doing the above on one queue after another may take a long time if
there are many queues on the system.
This patch splits out initiation of freezing and waiting for its
completion, and updates blk_mq_queue_reinit_notify() so that the
queues are frozen in parallel instead of one after another. Note that
freezing and unfreezing are moved from blk_mq_queue_reinit() to
blk_mq_queue_reinit_notify().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Baytrail-based chromebooks have a 20MHz mclk, the code was setting
the divisor incorrectly in this case. According to the 98090
datasheet, the divisor should be set to DIV1 for 10 <= mclk <= 20.
Correct this and the surrounding clock ranges as well to match the
datasheet.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull thermal fixes from Eduardo Valentin:
"Specifics:
- a few code fixes improving the Exynos code base. They remove dead
and unreachable code. No functional changes here
- in Exynos code base, fixes regarding the right usage of features
(TRIMINFO and TRIMRELOAD)
- documentation of RCAR thermal
- fix in the of-thermal, regarding the proper usage of of-APIs
- fixes on thermal-core, removal of unreachable code"
[ Eduardo is sending the thermal fixes on behalf of Rui Zhang this time.
Rui is currently unable to send pull requests due to troubles with his
machine and he's currently in a business trip ]
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Thermal:Remove usless if(!result) before return tz
thermal: exynos: fix IRQ clearing on TMU initialization
thermal: fix multiple disbalanced device node counters
thermal: rcar: Add binding docs for new R-Car Gen2 SoCs
thermal: exynos: Add support for TRIM_RELOAD feature at Exynos3250
thermal: exynos: Add support for many TRIMINFO_CTRL registers
thermal: samsung: Exynos5260 and Exynos5420 should not use TRIM_RELOAD flag
thermal: exynos: remove identical values from exynos*_tmu_registers structures
thermal: exynos: remove redundant pdata checks from exynos_tmu_control()
thermal: exynos: cache non_hw_trigger_levels in pdata
thermal: exynos: simplify temp_to_code() and code_to_temp()
thermal: exynos: remove redundant threshold_code checks from exynos_tmu_initialize()
thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize()
thermal: exynos: remove dead code for HW_MODE calibration
thermal: exynos: remove unused struct exynos_tmu_registers entries
Pull x86 platform drievr updates from Darren Hart:
"A short list of patches applying quirks and new DMI matches. These
pass my basic build tests and have spent 4 days in linux-next"
* tag 'platform-drivers-x86-v3.18-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
quirk for Lenovo Yoga 3: no rfkill switch
acer-wmi: Add acpi_backlight=video quirk for the Acer KAV80
samsung-laptop: Add broken-acpi-video quirk for NC210/NC110
asus-nb-wmi: Add wapf4 quirk for the X550VB
toshiba_acpi: Add Toshiba TECRA A50-A to the alt keymap dmi list
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes if you please"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: use device_online/offline() instead of cpu_up/down()
powerpc/powernv: Properly fix LPC debugfs endianness
powerpc: do_notify_resume can be called with bad thread_info flags argument
powerpc/fadump: Fix endianess issues in firmware assisted dump handling
powerpc: Fix section mismatch warning
Pull ftracetest fix from Steven Rostedt:
"Running the ftracetests on a machine that had the debugfs file system
mounted in two locations caused the ftracetests to fail. This is
because the ftracetests script does a grep of the /proc/mounts file to
find where the debugfs file system is mounted. If it is mounted
twice, then the grep returns two lines instead of just one. This
causes the ftracetests to get confused and fail.
Use "head -1" to only return the first mount point for debugfs"
* tag 'ftracetest-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftracetest: Take the first debugfs mount found
Changes into the AHCI subsystem have introduced a bug by not taking into
account the force_port_map and mask_port_map parameters when using the
ahci_pci_save_initial_config function. This commit fixes it by setting
the internal parameters of the ahci_port_priv structure.
Fixes: 725c7b570f
Reported-and-tested-by: Zlatko Calusic <zcalusic@bitsync.net>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
DPCM can update the FE/BE connection states totally asynchronously
from the FE's PCM state. Most of FE/BE state changes are protected by
mutex, so that they won't race, but there are still some actions that
are uncovered. For example, suppose to switch a BE while a FE's
stream is running. This would call soc_dpcm_runtime_update(), which
sets FE's runtime_update flag, then sets up and starts BEs, and clears
FE's runtime_update flag again.
When a device emits XRUN during this operation, the PCM core triggers
snd_pcm_stop(XRUN). Since the trigger action is an atomic ops, this
isn't blocked by the mutex, thus it kicks off DPCM's trigger action.
It eventually updates and clears FE's runtime_update flag while
soc_dpcm_runtime_update() is running concurrently, and it results in
confusion.
Usually, for avoiding such a race, we take a lock. There is a PCM
stream lock for that purpose. However, as already mentioned, the
trigger action is atomic, and we can't take the lock for the whole
soc_dpcm_runtime_update() or other operations that include the lengthy
jobs like hw_params or prepare.
This patch provides an alternative solution. This adds a way to defer
the conflicting trigger callback to be executed at the end of FE/BE
state changes. For doing it, two things are introduced:
- Each runtime_update state change of FEs is protected via PCM stream
lock.
- The FE's trigger callback checks the runtime_update flag. If it's
not set, the trigger action is executed there. If set, mark the
pending trigger action and returns immediately.
- At the exit of runtime_update state change, it checks whether the
pending trigger is present. If yes, it executes the trigger action
at this point.
Reported-and-tested-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If we hit any errors in btrfs_lookup_csums_range, we'll loop through all
the csums we allocate and free them. But the code was using list_entry
incorrectly, and ended up trying to free the on-stack list_head instead.
This bug came from commit 0678b6185
btrfs: Don't BUG_ON kzalloc error in btrfs_lookup_csums_range()
Signed-off-by: Chris Mason <clm@fb.com>
Reported-by: Erik Berg <btrfs@slipsprogrammoer.no>
cc: stable@vger.kernel.org # 3.3 or newer
We were returning maxlen like the userland strnlen if no '\0' character
was encountered while the kernel version is expected to return a value
larger than maxlen. Fixed to return maxlen + 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 64546e9fe3 ("ARM: imx_v6_v7_defconfig updates") and commit
0650f855d2 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI
selection was dropped by savedefconfig for imx_v4_v5_defconfig and
imx_v6_v7_defconfig.
In order to keep the same behaviour as previous kernel versions and avoid
regressions, let's add CONFIG_SPI option back.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The string property read helpers will run off the end of the buffer if
it is handed a malformed string property. Rework the parsers to make
sure that doesn't happen. At the same time add new test cases to make
sure the functions behave themselves.
The original implementations of of_property_read_string_index() and
of_property_count_strings() both open-coded the same block of parsing
code, each with it's own subtly different bugs. The fix here merges
functions into a single helper and makes the original functions static
inline wrappers around the helper.
One non-bugfix aspect of this patch is the addition of a new wrapper,
of_property_read_string_array(). The new wrapper is needed by the
device_properties feature that Rafael is working on and planning to
merge for v3.19. The implementation is identical both with and without
the new static inline wrapper, so it just got left in to reduce the
churn on the header file.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darren Hart <darren.hart@intel.com>
Cc: <stable@vger.kernel.org> # v3.3+: Drop selftest hunks that don't apply
sched_move_task() is the only interface to change sched_task_group:
cpu_cgrp_subsys methods and autogroup_move_group() use it.
Everything is synchronized by task_rq_lock(), so cpu_cgroup_attach()
is ordered with other users of sched_move_task(). This means we do no
need RCU here: if we've dereferenced a tg here, the .attach method
hasn't been called for it yet.
Thus, we should pass "true" to task_css_check() to silence lockdep
warnings.
Fixes: eeb61e53ea ("sched: Fix race between task_group and sched_task_group")
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414473874.8574.2.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e7
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull pin-control fixes from Linus Walleij:
"This kernel cycle has been calm for both pin control and GPIO so far
but here are three pin control patches for you anyway, only really
dealing with Baytrail:
- Two fixes for the Baytrail driver affecting IRQs and output state
in sysfs
- Use the linux-gpio mailing list also for pinctrl patches"
* tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: baytrail: show output gpio state correctly on Intel Baytrail
pinctrl: use linux-gpio mailing list
pinctrl: baytrail: Clear DIRECT_IRQ bit
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This contains important fixes for recently introduced highmem support
for default contiguous memory region used for dma-mapping subsystem"
* 'fixes-for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
mm, cma: make parameters order consistent in func declaration and definition
mm: cma: Use %pa to print physical addresses
mm: cma: Ensure that reservations never cross the low/high mem boundary
mm: cma: Always consider a 0 base address reservation as dynamic
mm: cma: Don't crash on allocation if CMA area can't be activated
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
When a subdriver is rmmod-ed then re-insmod-ed, the hid device is not
destroyed as it is owned by the transport layer.
So when we re-probed the device, the hid device is assumed to be already
claimed, and can lead to page faults if hid-core tries to forward the
emitted data to the to-be-created claimed node.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull m68k update from Geert Uytterhoeven.
Just wiring up the bpf system call.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up bpf
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipv6: Fix iflink setting for ipv6 tunnels
The ipv6 tunnels do the dev->iflink setting too early, it gets
overwritten by register_netdev(). So set dev->iflink from within
a ndo_init function to keep the configured setting.
This patchset fixes this for ip6_tunnel, vti6, sit and gre6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip6_tunnel_init() sets the dev->iflink via a call to
ipip6_tunnel_bind_dev(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ipip6_tunnel_init() as the
ndo_init function. Then ipip6_tunnel_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vti6_dev_init() sets the dev->iflink via a call to
vti6_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for vti6 tunnels. Fix this by using vti6_dev_init() as the
ndo_init function. Then vti6_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tnl_dev_init() sets the dev->iflink via a call to
ip6_tnl_link_config(). After that, register_netdevice()
sets dev->iflink = -1. So we loose the iflink configuration
for ipv6 tunnels. Fix this by using ip6_tnl_dev_init() as the
ndo_init function. Then ip6_tnl_dev_init() is called after
dev->iflink is set to -1 from register_netdevice().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4 ("macvtap: restore vlan header on user read")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu says:
====================
tun: Fix csum_start and TUN_PKT_STRIP
The first patch fixes a serious problem that breaks checksum offload
in VMs while the second patch fixes a problem that probably affects
no one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the flag TUN_PKT_STRIP if the user buffer provided is too
small to contain the entire packet plus meta-data. However, this
has been broken ever since we added GSO meta-data. VLAN acceleration
also has the same problem.
This patch fixes this by taking both into account when setting the
TUN_PKT_STRIP flag.
The fact that this has been broken for six years without anyone
realising means that nobody actually uses this flag.
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN acceleration is in use on the xmit path, we end up
setting csum_start to the wrong place. The result is that the
whoever ends up doing the checksum setting will corrupt the packet
instead of writing the checksum to the expected location, usually
this means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN acceleration
is detected.
Fixes: 6680ec68ef ("tuntap: hardware vlan tx support")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The makefile for sanitizing kernel headers uses the kbuild file
to determine which files to do. Several networking related headers
were missing. Without these headers iproute2 build would break.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
net/bridge/netfilter/nft_reject_bridge.c:
In function 'nft_reject_br_send_v6_unreach':
net/bridge/netfilter/nft_reject_bridge.c:240:3:
error: implicit declaration of function 'csum_ipv6_magic'
csum_ipv6_magic(&nip6h->saddr, &nip6h->daddr,
^
make[3]: *** [net/bridge/netfilter/nft_reject_bridge.o] Error 1
Seen with powerpc:allmodconfig.
Fixes: 523b929d54 ("netfilter: nft_reject_bridge: don't use IP stack to reject traffic")
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match is declared as a non-static local variable
so the structure members are not auto-initialized.
Initialize the struct at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct of_regulator_match rmatch[] is declared as a non-static local
variable so the structure members are not auto-initialized.
Initialize the array at declaration time to avoid the structure members
values to be indeterminate and have sane defaults instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver allocated on stack struct regulator_config but didn't initialize
it fully. Few fields (driver_data, ena_gpio) were left untouched. This
lead to using random ena_gpio values as GPIOs for max77693 regulators.
On occasion these values could match real GPIO numbers leading to
interfering with other drivers and to unsuccessful enable/disable of
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 80b022e29b ("regulator: max77693: Add max77693 regualtor driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
Cc: stable@vger.kernel.org
Reported-by: Yosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
Adds the missing comparison for the RC_BIT_OTHER.
Cc: stable@vger.kernel.org # for Kernel 3.17
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change CONFIG_PM to CONFIG_PM_SLEEP to solve
warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this warning:
drivers/s390/kvm/virtio_ccw.c: In function ‘virtio_ccw_int_handler’:
drivers/s390/kvm/virtio_ccw.c:891:24: warning: unused variable ‘drv’ [-Wunused-variable]
struct virtio_driver *drv;
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 0d930e51cf ("USB: opticon: Add Opticon OPN2001 write support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Write may be called from interrupt context so make sure to use
GFP_ATOMIC for all allocations in write.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
PREEMPT (and PREEMPT AND ABORT) should return CONFLICT iff a specified
SERVICE ACTION RESERVATION KEY is specified and matches no existing
persistent reservation.
Without this patch, a PREEMPT will return CONFLICT if either all
reservations are held by the initiator (self preemption) or there is
nothing to preempt. According to the spec, both of these cases should
succeed.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In this case the cm_id->context is the isert_np, and the cm_id->qp
is NULL, so use that to distinct the cases.
Since we don't expect any other events on this cm_id we can
just return -1 for explicit termination of the cm_id by the
cma layer.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a max_send_sge=2 minimum in isert_conn_setup_qp()
to ensure outgoing control PDU responses with tx_desc->num_sge=2
are able to function correctly.
This addresses a bug with RDMA hardware using dev_attr.max_sge=3,
that in the original code with the ConnectX-2 work-around would
result in isert_conn->max_sge=1 being negotiated.
Originally reported by Chris with ocrdma driver.
Reported-by: Chris Moore <Chris.Moore@emulex.com>
Tested-by: Chris Moore <Chris.Moore@emulex.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
* Factor out code for clearing raised IRQs from exynos_tmu_work() to
exynos_tmu_clear_irqs().
* Add a comment about documentation bugs to exynos_tmu_clear_irqs().
[ The documentation for Exynos3250, Exynos4412, Exynos5250 and
Exynos5260 incorrectly states that INTCLEAR register has
a different placing of bits responsible for FALL IRQs than
INTSTAT register. Exynos5420 and Exynos5440 documentation is
correct (Exynos4210 doesn't support FALL IRQs at all). ]
* Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead
of open-coded code trying to clear IRQs according to predefined
masks. After this change exynos_tmu_initialize() just clears
IRQs that are raised like it is already done in exynos_tmu_work().
As a nice side-effect the code now uses the correct offset
(16 instead of 12) for bits responsible for clearing FALL IRQs
in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250.
* Remove no longer needed intclr_rise_[mask,shift] and
intclr_fall_[mask,shift] fields from struct exynos_tmu_registers.
* Remove no longer needed defines.
This patch has been tested on Exynos4412 and Exynos5420 SoCs.
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Here on function return all temporarily used device nodes shall
decrement their usage counter. The problems are found with device
nodes allocated by for_each_child_of_node(), of_parse_phandle()
and of_find_node_by_name(), fix all problems at once.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: devicetree@vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently these SoCs claim TRIM_RELOAD support but don't have
triminfo_ctrl register address defined in their struct
exynos_tmu_registers entries. This causes incorrect write of
value "1" to data->base + 0x00 address (which happens to be
TRIMINFO register). Additionally according to the documentation
that I have neither Exynos5260 nor Exynos5420 support/require
TRIM_RELOAD feature. Thus fix the aforementioned issue by
removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and
Exynos5420.
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Amit Daniel Kachhap <amit.daniel@samsung.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need for abstracting configuration for registers that
are identical on all SoC types.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
pdata->reference_voltage and pdata->gain are always defined
to non-zero values so remove the redundant checks from
exynos_tmu_control().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Cache number of non-hardware trigger levels in a new pdata field
(non_hw_trigger_levels) and convert code in exynos_tmu_initialize()
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Remove dead temp check from temp_to_code() (this function users
in exynos_tmu_initialize() always pass correct temperatures and
exynos_tmu_set_emulation() returns early for EXYNOS4210 because
TMU_SUPPORT_EMULATION flag is not set on this SoC).
* Move temp_code check from code_to_temp() to exynos_tmu_read()
(code_to_temp() only user).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for negative return values of temp_to_code()
from exynos_tmu_initialize().
The current level temperature data hardcoded in pdata will never
cause a negative temp_to_code() return values and checking itself
is not proper. The checks in question are done at runtime in
a production code for data that is hardcoded inside driver during
development time and later it doesn't change. Such data should
be verified during development and review time (i.e. by a script
parsing relevant data from exynos_tmu_data.c, one can also argue
that verification to be done is so simple that the review by
a maintainer should be enough).
Theres should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove runtime checks for pdata sanity from exynos_tmu_initialize().
The current values hardcoded in pdata will never trigger the checks
and checking itself is not proper. The checks in question are done
at runtime in a production code for data that is hardcoded inside
driver during development time and later it doesn't change. Such
data should be verified during development and review time (i.e. by
a script parsing relevant data from exynos_tmu_data.c, one can also
argue that verification to be done is so simple that the review by
a maintainer should be enough).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The commit 1928457 ("thermal: exynos: Add hardware mode thermal
calibration support") has added HW_MODE feature but it has never
been enabled. As such it has been a dead code for over a year
now and should be removed from the kernel.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused / write-only entries from struct exynos_tmu_registers.
Then remove unused defines while at it.
We don't keep the unused/untested features in the kernel just
in case that some future hardware might need it. Such code has
a real maintainance cost (all other code changes have to take
the dead code into account) and usually makes future changes
more difficult, not easier (i.e. recent additions of Exynos5420
SoC and Exynos5260 SoC thermal support has not made use of any
of the driver's currently unused/untested features, moreover
the recently added code is more complex than needed because of
the existing dead code). Also all removed dead code is still
accessible in the kernel git repository and can be easily
brought back if/when needed.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull MTD fixes from Brian Norris:
"Three main MTD fixes for 3.18:
- A regression from 3.16 which was noticed in 3.17. With the
restructuring of the m25p80.c driver and the SPI NOR library
framework, we omitted proper listing of the SPI device IDs. This
means m25p80.c wouldn't auto-load (modprobe) properly when built as
a module. For now, we duplicate the device IDs into both modules.
- The OMAP / ELM modules were depending on an implicit link ordering.
Use deferred probing so that the new link order (in 3.18-rc) can
still allow for successful probing.
- Fix suspend/resume support for LH28F640BF NOR flash"
* tag 'for-linus-20141102' of git://git.infradead.org/linux-mtd:
mtd: cfi_cmdset_0001.c: fix resume for LH28F640BF chips
mtd: omap: fix mtd devices not showing up
mtd: m25p80,spi-nor: Fix module aliases for m25p80
mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
mtd: m25p80: get rid of spi_get_device_id
Pull SCSI fixes from James Bottomley:
"This is a set of six patches consisting of:
- two MAINTAINER updates
- two scsi-mq fixs for the old parallel interface (not every request
is tagged and we need to set the right flags to populate the SPI
tag message)
- a fix for a memory leak in scatterlist traversal caused by a
preallocation update in 3.17
- an ipv6 fix for cxgbi"
[ The scatterlist fix also came in separately through the block layer tree ]
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: ufs - remove self
MAINTAINERS: change hpsa and cciss maintainer
libcxgbi : support ipv6 address host_param
scsi: set REQ_QUEUE for the blk-mq case
Revert "block: all blk-mq requests are tagged"
lib/scatterlist: fix memory leak with scsi-mq
Pull drm fixes from Dave Airlie:
"Nothing too astounding or major: radeon, i915, vmwgfx, armada and
exynos.
Biggest ones:
- vmwgfx has one big locking regression fix
- i915 has come displayport fixes
- radeon has some stability and a memory alloc failure
- armada and exynos have some vblank fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/radeon: remove some buggy dead code
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
...
Merge "omap fixes against v3.18-rc2" from Tony Lindgren:
Few fixes for omaps to enable NAND BCH so devices won't
produce errors when booted with omap2plus_defconfig, and
reduce bloat by making IPV6 a loadable module.
Also let's add a warning about legacy boot being deprecated
for omap3.
We now have things working with device tree, and only omap3 is
still booting in legacy mode. So hopefully this warning will
help move the remaining legacy mode users to boot with device
tree.
As the total reduction of code and static data is somewhere
around 20000 lines of code once we remove omap3 legacy mode
booting, we really do want to make omap3 to boot also in
device tree mode only over the next few merge cycles.
* tag 'fixes-against-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (407 commits)
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
+ Linux 3.18-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
Pull kvm fixes from Paolo Bonzini:
"A small set of x86 fixes. The most serious is an SRCU lockdep fix.
A bit late - needed some time to test the SRCU fix, which only came in
on Friday"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: vmx: defer load of APIC access page address during reset
KVM: nVMX: Disable preemption while reading from shadow VMCS
KVM: x86: Fix far-jump to non-canonical check
KVM: emulator: fix execution close to the segment limit
KVM: emulator: fix error code for __linearize
This pull-request includes some bug fixes and code cleanups.
Especially, this fixes the bind failure issue occurred when it tries
to re-bind Exynos drm driver after unbound, and the modetest failure
issue incurred by not having a pair to vblank on and off requests.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: correct connector->dpms field before resuming
drm/exynos: enable vblank after DPMS on
drm/exynos: init kms poll at the end of initialization
drm/exynos: propagate plane initialization errors
drm/exynos: vidi: fix build warning
drm/exynos: remove explicit encoder/connector de-initialization
drm/exynos: init vblank with real number of crtcs
Pull VFS fixes from Al Viro:
"A bunch of assorted fixes, most of them followups to overlayfs merge"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: initialize ->is_cursor
Return short read or 0 at end of a raw device, not EIO
isofs: don't bother with ->d_op for normal case
isofs_cmp(): we'll never see a dentry for . or ..
overlayfs: fix lockdep misannotation
ovl: fix check for cursor
overlayfs: barriers for opening upper-layer directory
rcu: Provide counterpart to rcu_dereference() for non-RCU situations
staging: android: logger: Fix log corruption regression
The sk_prot is irda's own set of protocol handlers, so irda should
statically know what that function is anyway, without using an indirect
pointer. And as it happens, we know *exactly* what that pointer is
statically: it's NULL, because irda doesn't define a disconnect
operation.
So calling that function is doubly wrong, and will just cause an oops.
Reported-by: Martin Lang <mlg.hessigheim@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During system suspend after connector switch off its dpms field
is set to connector previous dpms state. To properly resume dpms field
should be set to its actual state (off) before resuming to previous dpms state.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Before DPMS off driver disables vblank.
It should be balanced by vblank enable after DPMS on.
The patch fixes issue with page_flip ioctl not being able
to acquire vblank counter introduced by patch:
drm: Always reject drm_vblank_get() after drm_vblank_off()
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HPD events can be generated by components even if drm_dev is not fully
initialized, to skip such events kms poll initialization should
be performed at the end of load callback followed directly by forced
connection detection.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In case of error during plane initialization load callback
incorrectly return success, this patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All KMS objects are destroyed by drm_mode_config_cleanup in proper order
so component drivers should not care about it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Initialization of vblank with MAX_CRTC caused attempts
to disabling vblanks for non-existing crtcs in case
drm used fewer crtcs. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In order to access the shadow VMCS, we need to load it. At this point,
vmx->loaded_vmcs->vmcs and the actually loaded one start to differ. If
we now get preempted by Linux, vmx_vcpu_put and, on return, the
vmx_vcpu_load will work against the wrong vmcs. That can cause
copy_shadow_to_vmcs12 to corrupt the vmcs12 state.
Fix the issue by disabling preemption during the copy operation.
copy_vmcs12_to_shadow is safe from this issue as it is executed by
vmx_vcpu_run when preemption is already disabled before vmentry.
This bug is exposed by running Jailhouse within KVM on CPUs with
shadow VMCS support. Jailhouse never expects an interrupt pending
vmexit, but the bug can cause it if, after copy_shadow_to_vmcs12
is preempted, the active VMCS happens to have the virtual interrupt
pending flag set in the CPU-based execution controls.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d1442d85cc ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In both Armada-375 and Armada-38x MPIC interrupts should be identified by
reading cause register multiplied by the interrupt mask.
A lack of above mentioned multiplication resulted in a bug, caused by the
fact that in Armada-375 and Armada-38x some of the interrupts
(e.g. network interrupts) can be handled either as a GIC or MPIC interrupts.
Therefore during MPIC interrupts handling, cause register shows hits from
interrupts even if they are masked for MPIC but unmasked for a GIC.
This resulted in 'bad IRQ' error, because masked MPIC interrupt without
registered interrupt handler, was trying to be handled during interrupt
handling procedure of some other unmasked MPIC interrupt (e.g. local timer
irq).
This commit fixes that by ensuring that during MPIC interrupt handling only
interrupts that are unmasked for MPIC are processed.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: bc69b8adfe ("irqchip: armada-370-xp: Setup a chained handler for the MPIC")
Cc: <stable@vger.kernel.org> # v3.15+
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1411643839-64925-3-git-send-email-jaz@semihalf.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In powerpc pseries platform dlpar operations, use device_online() and
device_offline() instead of cpu_up() and cpu_down().
Calling cpu_up/down() directly does not update the cpu device offline
field, which is used to online/offline a cpu from sysfs. Calling
device_online/offline() instead keeps the sysfs cpu online value
correct. The hotplug lock, which is required to be held when calling
device_online/offline(), is already held when dlpar_online/offline_cpu()
are called, since they are called only from cpu_probe|release_store().
This patch fixes errors on phyp (PowerVM) systems that have cpu(s)
added/removed using dlpar operations; without this patch, the
/sys/devices/system/cpu/cpuN/online nodes do not correctly show the
online state of added/removed cpus.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Fixes: 0902a9044f ("Driver core: Use generic offline/online for CPU offline/online")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A critical 3.18 regression fix from Rob, (thanks!)
A fix to avoid advertizing modes we can't support from Sinclair
(welcome Sinclair!)
and a fix for an incorrect hash key computation from me that is
completely harmless, but can wait 'til the next merge window if necessary.
(I can't really bother stable with this one).
* 'vmwgfx-fixes-3.18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Filter out modes those cannot be supported by the current VRAM size.
drm/vmwgfx: Fix hash key computation
drm/vmwgfx: fix lock breakage
Pull staging fixes from Greg KH:
"Here are some staging driver fixes for 3.18-rc3. Mostly iio and
comedi driver fixes for issues reported by people.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: fix memory leak / bad pointer freeing for chanlist
staging: comedi: Kconfig: fix config COMEDI_ADDI_APCI_3120 dependants
staging: comedi: widen subdevice number argument in ioctl handlers
staging: rtl8723au: Fix alignment of mac_addr for ether_addr_copy() usage
drivers/staging/comedi/Kconfig: Let COMEDI_II_PCI20KC depend on HAS_IOMEM
staging: comedi: (regression) channel list must be set for COMEDI_CMD ioctl
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.18-rc3.
Mostly usb-serial device ids and gadget fixes for issues that have
been reported. Full details are in the shortlog.
All of these have been in linux-next for a while"
* tag 'usb-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: chipidea: Fix oops when removing the ci_hdrc module
usb: gadget: function: Fixed the return value on error path
usb: dwc2: gadget: disable phy before turning off power regulators
usb: gadget: function: Remove redundant usb_free_all_descriptors
usb: dwc3: gadget: Properly initialize LINK TRB
usb: dwc2: gadget: fix gadget unregistration in udc_stop() function
usb: dwc2: Bits in bitfield should add up to 32
usb: dwc2: gadget: sparse warning of context imbalance
usb: gadget: udc: core: fix kernel oops with soft-connect
usb: musb: musb_dsps: fix NULL pointer in suspend
usb: musb: dsps: start OTG timer on resume again
usb: gadget: loopback: don't queue requests to bogus endpoints
usb: ffs: fix regression when quirk_ep_out_aligned_size flag is set
usb: gadget: f_fs: remove redundant ffs_data_get()
usb: gadget: udc: USB_GADGET_XILINX should depend on HAS_DMA
Revert "usb: dwc3: dwc3-omap: Disable/Enable only wrapper interrupts in prepare/complete"
usb: gadget: composite: enable BESL support
usb: musb: cppi41: restart hrtimer only if not yet done
usb: dwc3: ep0: fix Data Phase for transfer sizes aligned to wMaxPacketSize
usb: serial: ftdi_sio: add "bricked" FTDI device PID
...
The problem is that hardware handled by arm/plat-orion/gpio.c,
require ack for edge irq, and no ack for level irq.
The code handle this issue, by two "struct irq_chip_type" per
one "struct irq_chip_generic". For one "struct irq_chip_generic"
irq_ack pointer is setted, for another it is NULL.
But we have only one mask_cache per two "struct irq_chip_type".
So if we
1)unmask interrupt A for "edge type" trigger,
2)unmask interrupt B for "level type" trigger,
3)unmask interrupt C for "edge type",
we, because of usage of generic irq_gc_mask_clr_bit/irq_gc_mask_set_bit,
have hardware configured to trigger interrupt B on "edge type",
because of shared mask_cache. But kernel think that B is "level type",
so when interrupt B occur via "edge" reason, we don't ack it,
and B triggered again and again.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Link: https://lkml.kernel.org/r/20140726155659.GA22977@fifteen
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A second product has come to light which makes use of the A0 stepping
of the Armada XP SoC. A0 stepping has a hardware bug in the i2c core
meaning that hardware offload does not work, resulting in the kernel
failing to boot. The quirk detects that the kernel is running on an A0
stepping SoC and disables the use of hardware offload.
Currently the quirk is only enabled for PlatHome Openblocks AX3. The
AX3 has been produced with both A0 and B0 stepping SoCs. The second
product is the Lenovo Iomega IX4-300d. It seems likely that this
device will also swap from A0 to B0 SoC sometime during its life.
If there are two products using A0, it seems likely there are more
products with A0. Also, since the number of A0 SoCs is limited, these
products are also likely to transition to B0. Hence detecting at run
time is the safest option. So enable the quirk for all Armada XP
boards.
Tested on an AX3 with A0 stepping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403: ("i2c: mv64xxx: Add I2C Transaction Generator support")
Link: https://lkml.kernel.org/r/1406395238-29758-2-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When choosing a random address, the current implementation does not take into
account the reversed space for .bss and .brk sections. Thus the relocated kernel
may overlap other components in memory. Here is an example of the overlap from a
x86_64 kernel in qemu (the ranges of physical addresses are presented):
Physical Address
0x0fe00000 --+--------------------+ <-- randomized base
/ | relocated kernel |
vmlinux.bin | (from vmlinux.bin) |
0x1336d000 (an ELF file) +--------------------+--
\ | | \
0x1376d870 --+--------------------+ |
| relocs table | |
0x13c1c2a8 +--------------------+ .bss and .brk
| | |
0x13ce6000 +--------------------+ |
| | /
0x13f77000 | initrd |--
| |
0x13fef374 +--------------------+
The initrd image will then be overwritten by the memset during early
initialization:
[ 1.655204] Unpacking initramfs...
[ 1.662831] Initramfs unpacking failed: junk in compressed archive
This patch prevents the above situation by requiring a larger space when looking
for a random kernel base, so that existing logic can effectively avoids the
overlap.
[kees: switched to perl to avoid hex translation pain in mawk vs gawk]
[kees: calculated overlap without relocs table]
Fixes: 82fa9637a2 ("x86, kaslr: Select random position from e820 maps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Junjie Mao <eternal.n08@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1414762838-13067-1-git-send-email-eternal.n08@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konrad triggered the following splat below in a 32-bit guest on an AMD
box. As it turns out, in save_microcode_in_initrd_amd() we're using the
*physical* address of the container *after* we have enabled paging and
thus we #PF in load_microcode_amd() when trying to access the microcode
container in the ramdisk range.
Because the ramdisk is exactly there:
[ 0.000000] RAMDISK: [mem 0x35e04000-0x36ef9fff]
and we fault at 0x35e04304.
And since this guest doesn't relocate the ramdisk, we don't do the
computation which will give us the correct virtual address and we end up
with the PA.
So, we should actually be using virtual addresses on 32-bit too by the
time we're freeing the initrd. Do that then!
Unpacking initramfs...
BUG: unable to handle kernel paging request at 35d4e304
IP: [<c042e905>] load_microcode_amd+0x25/0x4a0
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.1-302.fc21.i686 #1
Hardware name: Xen HVM domU, BIOS 4.4.1 10/01/2014
task: f5098000 ti: f50d0000 task.ti: f50d0000
EIP: 0060:[<c042e905>] EFLAGS: 00010246 CPU: 0
EIP is at load_microcode_amd+0x25/0x4a0
EAX: 00000000 EBX: f6e9ec4c ECX: 00001ec4 EDX: 00000000
ESI: f5d4e000 EDI: 35d4e2fc EBP: f50d1ed0 ESP: f50d1e94
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 35d4e304 CR3: 00e33000 CR4: 000406d0
Stack:
00000000 00000000 f50d1ebc f50d1ec4 f5d4e000 c0d7735a f50d1ed0 15a3d17f
f50d1ec4 00600f20 00001ec4 bfb83203 f6e9ec4c f5d4e000 c0d7735a f50d1ed8
c0d80861 f50d1ee0 c0d80429 f50d1ef0 c0d889a9 f5d4e000 c0000000 f50d1f04
Call Trace:
? unpack_to_rootfs
? unpack_to_rootfs
save_microcode_in_initrd_amd
save_microcode_in_initrd
free_initrd_mem
populate_rootfs
? unpack_to_rootfs
do_one_initcall
? unpack_to_rootfs
? repair_env_string
? proc_mkdir
kernel_init_freeable
kernel_init
ret_from_kernel_thread
? rest_init
Reported-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=1158204
Fixes: 75a1ba5b2c ("x86, microcode, AMD: Unify valid container checks")
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # v3.14+
Link: http://lkml.kernel.org/r/20141101100100.GA4462@pd.tnic
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Florian Fainelli says:
====================
net: systemport: TX dma fixes
This patch series contains two fixes for our transmit path, first one
is a pretty nasty one since we were not allocating a large enough
dma coherent pool for our transmit descriptors, which would work most of the
time, since allocations are contiguous and we could have.
Second patch fixes a less frequent, though highly likley crash when using
CMA allocations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs fixes from Chris Mason:
"Filipe is nailing down some problems with our skinny extent variation,
and Dave's patch fixes endian problems in the new super block checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix race that makes btrfs_lookup_extent_info miss skinny extent items
Btrfs: properly clean up btrfs_end_io_wq_cache
Btrfs: fix invalid leaf slot access in btrfs_lookup_extent()
btrfs: use macro accessors in superblock validation checks
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
Pull PCI fixes from Bjorn Helgaas:
"These changes, intended for v3.18, fix:
Sysfs
- Fix "enable" filename change (Greg Kroah-Hartman)
An unintentional sysfs filename change in commit 5136b2da77
("PCI: convert bus code to use dev_groups"), which appeared in
v3.13, changed "enable" to "enabled", and this changes it back.
Old users of "enable" are currently broken and will be helped by
this change. Anything that started to use "enabled" after v3.13
will be broken by this change. If necessary, we can add a symlink
to make both work, but this patch doesn't do that.
PCI device hotplug
- Revert duplicate merge (Kamal Mostafa)
A mistaken duplicate merge that added a check twice. Nothing's
broken; this just removes the unnecessary code.
Freescale i.MX6
- Wait for clocks to stabilize after ref_en (Richard Zhu)
An i.MX6 clock problem that prevents mx6 nitrogen boards from booting"
* tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Rename sysfs 'enabled' file back to 'enable'
PCI: imx6: Wait for clocks to stabilize after ref_en
Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code
reads out of bounds, causing the NT fix to be unreliable. But, and
this is much, much worse, if your stack is somehow just below the
top of the direct map (or a hole), you read out of bounds and crash.
Excerpt from the crash:
[ 1.129513] RSP: 0018:ffff88001da4bf88 EFLAGS: 00010296
2b:* f7 84 24 90 00 00 00 testl $0x4000,0x90(%rsp)
That read is deterministically above the top of the stack. I
thought I even single-stepped through this code when I wrote it to
check the offset, but I clearly screwed it up.
Fixes: 8c7aa698ba ("x86_64, entry: Filter RFLAGS.NT on entry from userspace")
Reported-by: Rusty Russell <rusty@ozlabs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ext4 bugfixes from Ted Ts'o:
"A set of miscellaneous ext4 bug fixes for 3.18"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: make ext4_ext_convert_to_initialized() return proper number of blocks
ext4: bail early when clearing inode journal flag fails
ext4: bail out from make_indexed_dir() on first error
jbd2: use a better hash function for the revoke table
ext4: prevent bugon on race between write/fcntl
ext4: remove extent status procfs files if journal load fails
ext4: disallow changing journal_csum option during remount
ext4: enable journal checksum when metadata checksum feature enabled
ext4: fix oops when loading block bitmap failed
ext4: fix overflow when updating superblock backups after resize
Pull quota and ext3 fixes from Jan Kara.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs, jbd: use a more generic hash function
quota: Properly return errors from dquot_writeback_dquots()
ext3: Don't check quota format when there are no quota files
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
Pull sparc update from David Miller:
"Two changes:
1) It makes no sense to execute a VTOC partition table request in the
Sun virtual block device driver and fail to load if it doesn't
succeed because a) we don't use the result at all and b) it won't
succeed if there is an EFI partition on the disk, for example.
We read the partition table via the normal means in the block layer
anyways, so this is really completely useless, so just remove it.
From Dwight Engen.
2) Hook up new bpf system call"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: don't call VD_OP_GET_VTOC
sparc: Hook up bpf system call.
Pull Microblaze updates from Michal Simek:
- wire-up new bpf syscall
- fix PCI bug
- fix Kconfig warning
* tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Wire up bpf syscall
microblaze: Fix IO space breakage after of_pci_range_to_resource() change
microblaze: Fix missing NR_CPUS in menuconfig
Pull x86 fixes from Ingo Molnar:
"Fixes from all around the place:
- hyper-V 32-bit PAE guest kernel fix
- two IRQ allocation fixes on certain x86 boards
- intel-mid boot crash fix
- intel-quark quirk
- /proc/interrupts duplicate irq chip name fix
- cma boot crash fix
- syscall audit fix
- boot crash fix with certain TSC configurations (seen on Qemu)
- smpboot.c build warning fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE
ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi()
x86, intel-mid: Create IRQs for APB timers and RTC timers
x86: Don't enable F00F workaround on Intel Quark processors
x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts
x86, cma: Reserve DMA contiguous area after initmem_init()
i386/audit: stop scribbling on the stack frame
x86, apic: Handle a bad TSC more gracefully
x86: ACPI: Do not translate GSI number if IOAPIC is disabled
x86/smpboot: Move data structure to its primary usage scope
* acpi-scan:
ACPI: Use ACPI companion to match only the first physical device
* acpi-ec:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
Pull scheduler fixes from Ingo Molnar:
"Various scheduler fixes all over the place: three SCHED_DL fixes,
three sched/numa fixes, two generic race fixes and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/dl: Fix preemption checks
sched: Update comments for CLONE_NEWNS
sched: stop the unbound recursion in preempt_schedule_context()
sched/fair: Fix division by zero sysctl_numa_balancing_scan_size
sched/fair: Care divide error in update_task_scan_period()
sched/numa: Fix unsafe get_task_struct() in task_numa_assign()
sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer()
sched/deadline: Don't replenish from a !SCHED_DEADLINE entity
sched: Fix race between task_group and sched_task_group
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
Pull futex fixes from Ingo Molnar:
"This contains two futex fixes: one fixes a race condition, the other
clarifies shared/private futex comments"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix a race condition between REQUEUE_PI and task death
futex: Mention key referencing differences between shared and private futexes
Commit c27a3e4d66 ("libceph: do not hard code max auth ticket len")
while fixing a buffer overlow tried to keep the same as much of the
surrounding code as possible and introduced an unnecessary kmalloc() in
the unencrypted ticket path. It is likely to fail on huge tickets, so
get rid of it.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
John W. Linville says:
====================
pull request: wireless 2014-10-31
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core fixes from Ingo Molnar:
"The tree contains two RCU fixes and a compiler quirk comment fix"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_barrier() understand about missing rcuo kthreads
compiler/gcc4+: Remove inaccurate comment about 'asm goto' miscompiles
rcu: More on deadlock between CPU hotplug and expedited grace periods
Pull timer fixes from Thomas Gleixner:
"As you requested in the rc2 release mail the timer department serves
you a few real bug fixes:
- Fix the probe logic of the architected arm/arm64 timer
- Plug a stack info leak in posix-timers
- Prevent a shift out of bounds issue in the clockevents core"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/ARM64: arch-timer: fix arch_timer_probed logic
clockevents: Prevent shift out of bounds
posix-timers: Fix stack info leak in timer_create()
Pull tracing fix from Steven Rostedt:
"ARM has system calls outside the NR_syscalls range, and the generic
tracing system does not support that and without checks, it can cause
an oops to be reported.
Rabin Vincent added checks in the return code on syscall events to
make sure that the system call number is within the range that tracing
knows about, and if not, simply ignores the system call.
The system call tracing infrastructure needs to be rewritten to handle
these cases better, but for now, to keep from oopsing, this patch will
do"
* tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/syscalls: Ignore numbers outside NR_syscalls' range
Pull documentation fixes from Jonathan Corbet:
"So this is my first pull request since I rashly agreed to look after
the documentation subtree. It contains some typo fixes, a few minor
documentation improvements, and, most importantly, fixes for a couple
of build problems in various bits of sample code.
I fully intend to start sending pull requests with signed tags.
However, due to poor planning on my part and the general obnoxiousness
of life, I'm 2000 miles away from my private key which is sitting on a
powered-down machine. This should be fixed before my next request.
Meanwhile git.lwn.net is a machine under my control, the patches are
all trivial, and all have done time in linux-next"
* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6:
Documentation/SubmittingPatches: Reported-by tags and permission
Documentation: remove outdated references to the linux-next wiki
Documentation: Restrict TSC test code to x86
doc: kernel-parameters.txt: Add ide-generic.probe-mask
vdso: don't require 64-bit math in standalone test
Documentation: Add CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF case
Documentation: Add default kmemleak off case in kernel-parameters.txt
Docs: Document that the sticky bit is understood by hugetlbfs
DocBook: Reduce noise from make cleandocs
Documentation: fix vdso_standalone_test_x86 on 32-bit
Documentation: dt-bindings: Explain order in patch series
Documentation/ABI/testing/sysfs-ibft: fix a typo
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 68da166491.
It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Reported-by: Roel Aaij <roel.aaij@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq function altera_ps2_rxint returns an irqreturn_t, so use the
same type for variable storing the return value.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In altera_ps2_close, the data register (offset 0) is written instead of
the control register (offset 4), leading to the RX interrupt not being
disabled. Fix this by calling writel() with the offset for the proper
register.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.
Reported by Coverity: CID 1248753
Acked-by : Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pablo Neira Ayuso says:
====================
netfilter/ipvs fixes for net
The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:
1) Fix a null-pointer dereference that may occur when logging
errors. This problem was introduced by 4a4739d56b ("ipvs: Pull
out crosses_local_route_boundary logic") in v3.17-rc5.
2) Update hook mask in nft_reject_bridge so we can also filter out
packets from there. This fixes 36d2af5 ("netfilter: nf_tables: allow
to filter from prerouting and postrouting"), which needs this chunk
to work.
3) Two patches to refactor common code to forge the IPv4 and IPv6
reject packets from the bridge. These are required by the nf_tables
reject bridge fix.
4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
packets from the bridge. The idea is to forge the reject packets and
inject them to the original port via br_deliver() which is now
exported for that purpose.
5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
the original skbuff may cloned after prerouting when the bridge stack
needs to flood it to several bridge ports, it is too late to reject
the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Priority of a merged request is computed by ioprio_best(). If one of the
requests has undefined priority (IOPRIO_CLASS_NONE) and another request
has priority from IOPRIO_CLASS_BE, the function will return the
undefined priority which is wrong. Fix the function to properly return
priority of a request with the defined priority.
Fixes: d58cdfb89c
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.
This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:
1) Validate the IPv4 and IPv6 headers before further processing,
given that the packet comes from the bridge stack, we cannot assume
they are clean. Truncated packets are dropped, we follow similar
approach in the existing iptables match/target extensions that need
to inspect layer 4 headers that is not available. This also includes
packets that are directed to multicast and broadcast ethernet
addresses.
2) br_deliver() is exported to inject the reject packet via
bridge localout -> postrouting. So the approach is similar to what
we already do in the iptables reject target. The reject packet is
sent to the bridge port from which we have received the original
packet.
3) The reject packet is forged based on the original packet. The TTL
is set based on sysctl_ip_default_ttl for IPv4 and per-net
ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip6_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_ip6hdr_put(): to build the IPv6 header.
* nf_reject_ip6_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.
v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
The hash key computation in vmw_cmdbuf_res_remove incorrectly didn't take
the resource type into account, contrary to all the other related functions.
This becomes important when the cmdbuf resource manager handles more than
one resource type.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
After:
commit d059f652e7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Fri Jul 25 18:07:40 2014 +0200
drm: Handle legacy per-crtc locking with full acquire ctx
drm_mode_cursor_common() was switched to use drm_modeset_(un)lock_crtc()
which uses full aquire ctx. So dropping/reaquiring the lock via
drm_modeset_(un)lock() directly isn't the right thing to do, as lockdep
kindly points out.
The 'FIXME's about sorting out whether vmwgfx *really* needs to lock-all
for cursor updates still apply.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas Hellstrom <thellstrom@vmware.com>
Endian is hard, especially when I designed a stupid FW interface, and
I should know better... oh well, this is attempt #2 at fixing this
properly. This time it seems to work with all access sizes and I
can run my flashing tool (which exercises all sort of access sizes
and types to access the SPI controller in the BMC) just fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 7230c56441 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:
bl restore_interrupts
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_notify_resume
Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:
void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.
LLVM on the other hand did trample r4.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c5 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM has some private syscalls (for example, set_tls(2)) which lie
outside the range of NR_syscalls. If any of these are called while
syscall tracing is being performed, out-of-bounds array access will
occur in the ftrace and perf sys_{enter,exit} handlers.
# trace-cmd record -e raw_syscalls:* true && trace-cmd report
...
true-653 [000] 384.675777: sys_enter: NR 192 (0, 1000, 3, 4000022, ffffffff, 0)
true-653 [000] 384.675812: sys_exit: NR 192 = 1995915264
true-653 [000] 384.675971: sys_enter: NR 983045 (76f74480, 76f74000, 76f74b28, 76f74480, 76f76f74, 1)
true-653 [000] 384.675988: sys_exit: NR 983045 = 0
...
# trace-cmd record -e syscalls:* true
[ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace
[ 17.289590] pgd = 9e71c000
[ 17.289696] [aaaaaace] *pgd=00000000
[ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 17.290169] Modules linked in:
[ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21
[ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000
[ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8
[ 17.290866] LR is at syscall_trace_enter+0x124/0x184
Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers.
Commit cd0980fc8a "tracing: Check invalid syscall nr while tracing syscalls"
added the check for less than zero, but it should have also checked
for greater than NR_syscalls.
Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in
Fixes: cd0980fc8a "tracing: Check invalid syscall nr while tracing syscalls"
Cc: stable@vger.kernel.org # 2.6.33+
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Ben Hutchings says:
====================
drivers/net,ipv6: Fix IPv6 fragment ID selection for virtio
The virtio net protocol supports UFO but does not provide for passing a
fragment ID for fragmentation of IPv6 packets. We used to generate a
fragment ID wherever such a packet was fragmented, but currently we
always use ID=0!
v2: Add blank lines after declarations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header. UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.
Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug. Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.
Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.
We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()
Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f3279ae0c ("tcp: avoid retransmits of TCP packets hanging in host queues")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.
Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver encapsulation/steering fixes
The 1st patch fixes a bug in the TX path that supports offloading the
TX checksum of (VXLAN) encapsulated TCP packets. It turns out that the
bug is revealed only when the receiver runs in non-offloaded mode, so
we somehow missed it so far... please queue it for -stable >= 3.14
The 2nd patch makes sure not to leak steering entry on error flow,
please queue it to 3.17-stable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-30
This series contains updates to e1000, igb and ixgbe.
Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.
Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.
Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.
Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not. Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them. The opposite
is also true.
This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The man page for open(2) indicates that when O_CREAT is specified, the
'mode' argument applies only to future accesses to the file:
Note that this mode applies only to future accesses of the newly
created file; the open() call that creates a read-only file
may well return a read/write file descriptor.
The man page for open(2) implies that 'mode' is treated identically by
O_CREAT and O_TMPFILE.
O_TMPFILE, however, behaves differently:
int fd = open("/tmp", O_TMPFILE | O_RDWR, 0);
assert(fd == -1);
assert(errno == EACCES);
int fd = open("/tmp", O_TMPFILE | O_RDWR, 0600);
assert(fd > 0);
For O_CREAT, do_last() sets acc_mode to MAY_OPEN only:
if (*opened & FILE_CREATED) {
/* Don't check for write permission, don't truncate */
open_flag &= ~O_TRUNC;
will_truncate = false;
acc_mode = MAY_OPEN;
path_to_nameidata(path, nd);
goto finish_open_created;
}
But for O_TMPFILE, do_tmpfile() passes the full op->acc_mode to
may_open().
This patch lines up the behavior of O_TMPFILE with O_CREAT. After the
inode is created, may_open() is called with acc_mode = MAY_OPEN, in
do_tmpfile().
A different, but related glibc bug revealed the discrepancy:
https://sourceware.org/bugzilla/show_bug.cgi?id=17523
The glibc lazily loads the 'mode' argument of open() and openat() using
va_arg() only if O_CREAT is present in 'flags' (to support both the 2
argument and the 3 argument forms of open; same idea for openat()).
However, the glibc ignores the 'mode' argument if O_TMPFILE is in
'flags'.
On x86_64, for open(), it magically works anyway, as 'mode' is in
RDX when entering open(), and is still in RDX on SYSCALL, which is where
the kernel looks for the 3rd argument of a syscall.
But openat() is not quite so lucky: 'mode' is in RCX when entering the
glibc wrapper for openat(), while the kernel looks for the 4th argument
of a syscall in R10. Indeed, the syscall calling convention differs from
the regular calling convention in this respect on x86_64. So the kernel
sees mode = 0 when trying to use glibc openat() with O_TMPFILE, and
fails with EACCES.
Signed-off-by: Eric Rannaud <e@nanocritical.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- dpm stability fixes for SI and KV
- remove an invalid pci id
- kmalloc_array fixes
- minor cleanups
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: remove some buggy dead code
drm/radeon: remove invalid pci id
drm/radeon: dpm fixes for asrock systems
radeon: clean up coding style differences in radeon_get_bios()
drm/radeon: Use drm_malloc_ab instead of kmalloc_array
drm/radeon/dpm: disable ulv support on SI
bunch of DP fixes, and some backlight fix.
* tag 'drm-intel-fixes-2014-10-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915/dp: only use training pattern 3 on platforms that support it
drm/i915: Ignore VBT backlight check on Macbook 2, 1
drm/i915: Fix GMBUSFREQ on vlv/chv
drm/i915: Ignore long hpds on eDP ports
drm/i915: Do a dummy DPCD read before the actual read
win0_lock was being used un-initialized, resulting in warning traces
being seen when lock debugging is enabled (and just wrong)
Fixes : fc5ab02096 ('cxgb4: Replaced the backdoor mechanism to access the HW
memory with PCIe Window method')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: patches for autosuspend
There are unexpected processes when enabling autosuspend.
These patches are used to fix them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new version of rtlwifi needs code in rtl92ce_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new version of rtlwifi needs code in rtl92se_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtlwifi has been modified to call ieee80211_register_hw()
from the probe routine; however, the existing call in the callback
routine for deferred firmware loading was not removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes in checking for Bluetooth status added some callbacks to code
in rtlwifi. To make certain that all callbacks are defined, a dummy routine has been
added to rtlwifi, and the drivers that need to use it are modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During 11n RX reordering, if there is a hole in RX table,
driver will not send packets to kernel until the rxreorder
timer expires or the table is full.
However, currently driver always restarts rxreorder timer when
receiving a packet, which causes the timer hardly to expire.
So while connected with to 11n AP in a busy environment,
ping packets may get blocked for about 30 seconds.
This patch fixes this timer restarting by ensuring rxreorder timer
would only be restarted either timer is not set or start_win
has changed.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Plus Chen <pchen@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask. It should be left shift, mask, and then right shift.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not
automatically power down. This blocks other receivers connected
to a satellite channel router (EN50494), since the receivers can not send the
required DiSEqC sequences when the Tevii card is connected to a the same SCR.
This patch switches off the LNB supply voltage on initialization of the frontend.
[mchehab@osg.samsung.com: add a comment about why we're explicitly
turning off voltage at device init]
Cc: stable@vger.kernel.org
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Back in commit 5136b2da77 ("PCI: convert bus code to use dev_groups"),
I misstyped the 'enable' sysfs filename as 'enabled', which broke the
userspace API. This patch fixes that issue by renaming the file back.
Fixes: 5136b2da77 ("PCI: convert bus code to use dev_groups")
Reported-by: Jeff Epler <jepler@unpythonic.net>
Tested-by: Jeff Epler <jepler@unpythonic.net> # on v3.14-rt
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # 3.13
This fix rectifies the psci cpu_suspend implementation to check the
PSCI power state parameter type field associated with the requested idle
state index.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull sound fixes from Takashi Iwai:
"Although the diffstat looks scary, it's just because of the removal of
the dead code (s6000), thus it must not affect anything serious.
Other than that, all small fixes. The only core fix is zero-clear for
a PCM compat ioctl. The rest are driver-specific, bebob, sgtl500,
adau1761, intel-sst, ad1889 and a few HD-audio quirks as usual"
* tag 'sound-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add workaround for CMI8888 snoop behavior
ALSA: pcm: Zero-clear reserved fields of PCM status ioctl in compat mode
ALSA: bebob: Uninitialized id returned by saffirepro_both_clk_src_get
ALSA: hda/realtek - New SSID for Headset quirk
ALSA: ad1889: Fix probable mask then right shift defects
ALSA: bebob: fix wrong decoding of clock information for Terratec PHASE 88 Rack FW
ALSA: hda/realtek - Update restore default value for ALC283
ALSA: hda/realtek - Update restore default value for ALC282
ASoC: fsl: use strncpy() to prevent copying of over-long names
ASoC: adau1761: Fix input PGA volume
ASoC: s6000: remove driver
ASoC: Intel: HSW/BDW only support S16 and S24 formats.
ASoC: sgtl500: Document the required supplies
ext4_ext_convert_to_initialized() can return more blocks than are
actually allocated from map->m_lblk in case where initial part of the
on-disk extent is zeroed out. Luckily this doesn't have serious
consequences because the caller currently uses the return value
only to unmap metadata buffers. Anyway this is a data
corruption/exposure problem waiting to happen so fix it.
Coverity-id: 1226848
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When clearing inode journal flag, we call jbd2_journal_flush() to force
all the journalled data to their final locations. Currently we ignore
when this fails and continue clearing inode journal flag. This isn't a
big problem because when jbd2_journal_flush() fails, journal is likely
aborted anyway. But it can still lead to somewhat confusing results so
rather bail out early.
Coverity-id: 989044
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When ext4_handle_dirty_dx_node() or ext4_handle_dirty_dirent_node()
fail, there's really something wrong with the fs and there's no point in
continuing further. Just return error from make_indexed_dir() in that
case. Also initialize frames array so that if we return early due to
error, dx_release() doesn't try to dereference uninitialized memory
(which could happen also due to error in do_split()).
Coverity-id: 741300
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
The old hash function didn't work well for 64-bit block numbers, and
used undefined (negative) shift right behavior. Use the generic
64-bit hash function instead.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Andrey Ryabinin <a.ryabinin@samsung.com>
If we can't load the journal, remove the procfs files for the extent
status information file to avoid leaking resources.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
ext4 does not permit changing the metadata or journal checksum feature
flag while mounted. Until we decide to support that, don't allow a
remount to change the journal_csum flag (right now we silently fail to
change anything).
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When we fail to load block bitmap in __ext4_new_inode() we will
dereference NULL pointer in ext4_journal_get_write_access(). So check
for error from ext4_read_block_bitmap().
Coverity-id: 989065
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When there are no meta block groups update_backups() will compute the
backup block in 32-bit arithmetics thus possibly overflowing the block
number and corrupting the filesystem. OTOH filesystems without meta
block groups larger than 16 TB should be rare. Fix the problem by doing
the counting in 64-bit arithmetics.
Coverity-id: 741252
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.
However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.
To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Without that fix connector-analog-tv driver isn't probed when compiled
as module.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Incoming packet is dropped silently by sk_filter(), if the skb was
allocated from pfmemalloc reserves and the corresponding socket is
not marked with the SOCK_MEMALLOC flag.
Igb driver allocates pages for DMA with __skb_alloc_page(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, igb can get pages with pfmemalloc flag set.
If an incoming packet hits the pfmemalloc page and is large enough
(small packets are copying into the memory, allocated with
netdev_alloc_skb_ip_align(), so they are not affected), it will be
dropped.
This behavior is ok under high memory pressure, but the problem is
that the igb driver reuses these mapped pages. So, packets are still
dropping even if all memory issues are gone and there is a plenty
of free memory.
In my case, some TCP sessions hang on a small percentage (< 0.1%)
of machines days after OOMs.
Fix this by avoiding reuse of such pages.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Tested-by: Aaron Brown "aaron.f.brown@intel.com"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changeset e87b540be2 broke RC5-SZ decoding, as it forgot to add
the extra bit check for the enabled protocols at the beginning of
the logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IR receiver using nuvoton-cir and lirc required additional configuration
steps after upgrade from kernel 3.16 to 3.17-rcX. Bisected regression to
commit da6e162d6a ("[media] rc-core:
simplify sysfs code").
The regression comes from adding function change_protocol in ir-raw.c.
It changes behaviour so that only the protocol enabled by driver's
map_name will be active after registration. This breaks user space
behaviour, lirc does not get key press signals anymore.
Enable lirc protocol by default for ir raw decoders to restore original
behaviour.
Cc: stable@vger.kernel.org # for v3.17
Signed-off-by: Tomas Melin <tomas.melin@iki.fi>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch has ceph's lib code use the memalloc flags.
If the VM layer needs to write data out to free up memory to handle new
allocation requests, the block layer must be able to make forward progress.
To handle that requirement we use structs like mempools to reserve memory for
objects like bios and requests.
The problem is when we send/receive block layer requests over the network
layer, net skb allocations can fail and the system can lock up.
To solve this, the memalloc related flags were added. NBD, iSCSI
and NFS uses these flags to tell the network/vm layer that it should
use memory reserves to fullfill allcation requests for structs like
skbs.
I am running ceph in a bunch of VMs in my laptop, so this patch was
not tested very harshly.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Ilya Dryomov <idryomov@redhat.com>
Using one queue per device doesn't make much sense given that our
workfn processes "devices" and not "requests". Switch to a single
workqueue for all devices.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
The default EAPD control uses verb command to control EAPD. Some codec
does not have verb command for EAPD. It needs to control by hidden
register.
This update will avoid wrong behavior for some codec. This patch will
fix double setup for EAPD. It just needs to turn on by one site for
verb command or hidden register controlled.
Detailed changes:
- alc889_coef_init() is replaced with alc_update_coef_idx() with a
correct COEF value.
- for ALC262, ALC887 and ALC900, the EAPD setup via the hidden
register is removed because this rather conflicts with the EAPD verb
setup.
- For ALC888-VC, also the hidden register access is removed in
alc888_coef_init().
- Remove the dead #if 0 code for ALC267/ALC268.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These three HP machines all have the same pin config, so we can
change it to a pin quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull two RCU fixes from Paul E. McKenney:
" - Complete the work of commit dd56af42bd (rcu: Eliminate deadlock
between CPU hotplug and expedited grace periods), which was
intended to allow synchronize_sched_expedited() to be safely
used when holding locks acquired by CPU-hotplug notifiers.
This commit makes the put_online_cpus() avoid the deadlock
instead of just handling the get_online_cpus().
- Complete the work of commit 35ce7f29a4 (rcu: Create rcuo
kthreads only for onlined CPUs), which was intended to allow
RCU to avoid allocating unneeded kthreads on systems where the
firmware says that there are more CPUs than are really present.
This commit makes rcu_barrier() aware of the mismatch, so that
it doesn't hang waiting for non-existent CPUs. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix report -F (abort, in_tx, mispredict, etc) segfaults for sample.data files
without branch info (Jiri Olsa)
- Add patch that should have went in a previous patchkit to use global cache
provided by libunwind (Namhyung Kim)
- Make CPUINFO_PROC an array to support different kernels, problem
detected when the information reported via /proc/cpuinfo changed on ARM (Wang Nan)
- 'perf probe' --demangle typo fix and a new --quiet option (Masami Hiramatsu)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After '#echo mem > /sys/power/state' some devices can not be properly resumed
because apparently the MTD Partition Configuration Register has been reset
to default thus the rootfs cannot be mounted cleanly on resume.
An example of this can be found in the SA-1100 Developer's Manual at 9.5.3.3
where the second step of the Sleep Shutdown Sequence is described:
"An internal reset is applied to the SA-1100. All units are reset...".
As workaround we refresh the PCR value as done initially on chip setup.
This behavior and the fix are confirmed by our tests done on 2 different Zaurus
collie units with kernel 3.17.
Fixes: 812c5fa82b: ("mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR")
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since commit 6d178ef2fd ("mtd: nand: Move ELM driver and rename as
omap_elm"), I don't have any mtd devices present on my am335x. This
changes the link order of the omap_elm and omap2 objects, causing them
to probe in the wrong order.
To fix this, make elm_config defer probing until the omap_elm driver is
actually loaded.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The wireless hotkey of Dell Vostro 3546 does not work with Win8 OSI. Due
to insufficient documentation for the driver implementation, blacklist
it as a workaround.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add __init to MMU_setup() which uses __initdata boot_command_line.
Also MMU_setup() is only called from MMU_init(), which is also __init.
Warning appeared since commit 3e47d1474c.
Fixes: 3e47d1474c ("powerpc: Remove powerpc specific cmd_line")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[mpe: Update changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
mm/balloon_compaction: fix deflation when compaction is disabled
sh: fix sh770x SCIF memory regions
zram: avoid NULL pointer access in concurrent situation
mm/slab_common: don't check for duplicate cache names
ocfs2: fix d_splice_alias() return code checking
mm: rmap: split out page_remove_file_rmap()
mm: memcontrol: fix missed end-writeback page accounting
mm: page-writeback: inline account_page_dirtied() into single caller
lib/bitmap.c: fix undefined shift in __bitmap_shift_{left|right}()
drivers/rtc/rtc-bq32k.c: fix register value
memory-hotplug: clear pgdat which is allocated by bootmem in try_offline_node()
drivers/rtc/rtc-s3c.c: fix initialization failure without rtc source clock
kernel/kmod: fix use-after-free of the sub_info structure
drivers/rtc/rtc-pm8xxx.c: rework to support pm8941 rtc
mm, thp: fix collapsing of hugepages on madvise
drivers: of: add return value to of_reserved_mem_device_init()
mm: free compound page with correct order
gcov: add ARM64 to GCOV_PROFILE_ALL
fsnotify: next_i is freed during fsnotify_unmount_inodes.
mm/compaction.c: avoid premature range skip in isolate_migratepages_range
...
The zero range operation is analogous to fallocate with the exception of
converting the range to zeroes. E.g., it attempts to allocate zeroed
blocks over the range specified by the caller. The XFS implementation
kills all delalloc blocks currently over the aligned range, converts the
range to allocated zero blocks (unwritten extents) and handles the
partial pages at the ends of the range by sending writes through the
pagecache.
The current implementation suffers from several problems associated with
inode size. If the aligned range covers an extending I/O, said I/O is
discarded and an inode size update from a previous write never makes it
to disk. Further, if an unaligned zero range extends beyond eof, the
page write induced for the partial end page can itself increase the
inode size, even if the zero range request is not supposed to update
i_size (via KEEP_SIZE, similar to an fallocate beyond EOF).
The latter behavior not only incorrectly increases the inode size, but
can lead to stray delalloc blocks on the inode. Typically, post-eof
preallocation blocks are either truncated on release or inode eviction
or explicitly written to by xfs_zero_eof() on natural file size
extension. If the inode size increases due to zero range, however,
associated blocks leak into the address space having never been
converted or mapped to pagecache pages. A direct I/O to such an
uncovered range cannot convert the extent via writeback and will BUG().
For example:
$ xfs_io -fc "pwrite 0 128k" -c "fzero -k 1m 54321" <file>
...
$ xfs_io -d -c "pread 128k 128k" <file>
<BUG>
If the entire delalloc extent happens to not have page coverage
whatsoever (e.g., delalloc conversion couldn't find a large enough free
space extent), even a full file writeback won't convert what's left of
the extent and we'll assert on inode eviction.
Rework xfs_zero_file_space() to avoid buffered I/O for partial pages.
Use the existing hole punch and prealloc mechanisms as primitives for
zero range. This implementation is not efficient nor ideal as we
writeback dirty data over the range and remove existing extents rather
than convert to unwrittern. The former writeback, however, is currently
the only mechanism available to ensure consistency between pagecache and
extent state. Even a pagecache truncate/delalloc punch prior to hole
punch has lead to inconsistencies due to racing with writeback.
This provides a consistent, correct implementation of zero range that
survives fsstress/fsx testing without assert failures. The
implementation can be optimized from this point forward once the
fundamental issue of pagecache and delalloc extent state consistency is
addressed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The WARN_ON checking whether i_mutex is held in
pagecache_isize_extended() was wrong because some filesystems (e.g.
XFS) use different locks for serialization of truncates / writes. So
just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xfs_bulkstat() doesn't check error return from xfs_btree_increment(). In
case of specific fs corruption that could result in xfs_bulkstat()
entering an infinite loop because we would be looping over the same
chunk over and over again. Fix the problem by checking the return value
and terminating the loop properly.
Coverity-id: 1231338
cc: <stable@vger.kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jie Liu <jeff.u.liu@gmail.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
If CONFIG_BALLOON_COMPACTION=n balloon_page_insert() does not link pages
with balloon and doesn't set PagePrivate flag, as a result
balloon_page_dequeue() cannot get any pages because it thinks that all
of them are isolated. Without balloon compaction nobody can isolate
ballooned pages. It's safe to remove this check.
Fixes: d6d86c0a7f ("mm/balloon_compaction: redesign ballooned pages management").
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Reported-by: Matt Mullins <mmullins@mmlx.us>
Cc: <stable@vger.kernel.org> [3.17]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a rare NULL pointer bug in mem_used_total_show() and
mem_used_max_store() in concurrent situation, like this:
zram is not initialized, process A is a mem_used_total reader which runs
periodically, while process B try to init zram.
process A process B
access meta, get a NULL value
init zram, done
init_done() is true
access meta->mem_pool, get a NULL pointer BUG
This patch fixes this issue.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SLUB cache merges caches with the same size and alignment and there
was long standing bug with this behavior:
- create the cache named "foo"
- create the cache named "bar" (which is merged with "foo")
- delete the cache named "foo" (but it stays allocated because "bar"
uses it)
- create the cache named "foo" again - it fails because the name "foo"
is already used
That bug was fixed in commit 694617474e ("slab_common: fix the check
for duplicate slab names") by not warning on duplicate cache names when
the SLUB subsystem is used.
Recently, cache merging was implemented the with SLAB subsystem too, in
12220dea07 ("mm/slab: support slab merge")). Therefore we need stop
checking for duplicate names even for the SLAB subsystem.
This patch fixes the bug by removing the check.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
d_splice_alias() can return a valid dentry, NULL or an ERR_PTR.
Currently the code checks not for ERR_PTR and will cuase an oops in
ocfs2_dentry_attach_lock(). Fix this by using IS_ERR_OR_NULL().
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0a31bc97c8 ("mm: memcontrol: rewrite uncharge API") changed
page migration to uncharge the old page right away. The page is locked,
unmapped, truncated, and off the LRU, but it could race with writeback
ending, which then doesn't unaccount the page properly:
test_clear_page_writeback() migration
wait_on_page_writeback()
TestClearPageWriteback()
mem_cgroup_migrate()
clear PCG_USED
mem_cgroup_update_page_stat()
if (PageCgroupUsed(pc))
decrease memcg pages under writeback
release pc->mem_cgroup->move_lock
The per-page statistics interface is heavily optimized to avoid a
function call and a lookup_page_cgroup() in the file unmap fast path,
which means it doesn't verify whether a page is still charged before
clearing PageWriteback() and it has to do it in the stat update later.
Rework it so that it looks up the page's memcg once at the beginning of
the transaction and then uses it throughout. The charge will be
verified before clearing PageWriteback() and migration can't uncharge
the page as long as that is still set. The RCU lock will protect the
memcg past uncharge.
As far as losing the optimization goes, the following test results are
from a microbenchmark that maps, faults, and unmaps a 4GB sparse file
three times in a nested fashion, so that there are two negative passes
that don't account but still go through the new transaction overhead.
There is no actual difference:
old: 33.195102545 seconds time elapsed ( +- 0.01% )
new: 33.199231369 seconds time elapsed ( +- 0.03% )
The time spent in page_remove_rmap()'s callees still adds up to the
same, but the time spent in the function itself seems reduced:
# Children Self Command Shared Object Symbol
old: 0.12% 0.11% filemapstress [kernel.kallsyms] [k] page_remove_rmap
new: 0.12% 0.08% filemapstress [kernel.kallsyms] [k] page_remove_rmap
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Cc: <stable@vger.kernel.org> [3.17.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by
a multiple of BITS_PER_LONG, they will try to shift a long value by
BITS_PER_LONG bits which is undefined. Change the functions to avoid
the undefined shift.
Coverity id: 1192175
Coverity id: 1192174
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix register value in bq32000 trickle charging.
Mike reported that I'm using wrong value in one trickle-charging case,
and after checking docs, I must admit he's right.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Mike Bremford <mike@bfo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When hot adding the same memory after hot removal, the following
messages are shown:
WARNING: CPU: 20 PID: 6 at mm/page_alloc.c:4968 free_area_init_node+0x3fe/0x426()
...
Call Trace:
dump_stack+0x46/0x58
warn_slowpath_common+0x81/0xa0
warn_slowpath_null+0x1a/0x20
free_area_init_node+0x3fe/0x426
hotadd_new_pgdat+0x90/0x110
add_memory+0xd4/0x200
acpi_memory_device_add+0x1aa/0x289
acpi_bus_attach+0xfd/0x204
acpi_bus_attach+0x178/0x204
acpi_bus_scan+0x6a/0x90
acpi_device_hotplug+0xe8/0x418
acpi_hotplug_work_fn+0x1f/0x2b
process_one_work+0x14e/0x3f0
worker_thread+0x11b/0x510
kthread+0xe1/0x100
ret_from_fork+0x7c/0xb0
The detaled explanation is as follows:
When hot removing memory, pgdat is set to 0 in try_offline_node(). But
if the pgdat is allocated by bootmem allocator, the clearing step is
skipped.
And when hot adding the same memory, the uninitialized pgdat is reused.
But free_area_init_node() checks wether pgdat is set to zero. As a
result, free_area_init_node() hits WARN_ON().
This patch clears pgdat which is allocated by bootmem allocator in
try_offline_node().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unconditional initialization failure on non-exynos3250 SoCs.
Commit df9e26d093 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
introduced rtc source clock support, but also added initialization
failure on SoCs, which doesn't need such clock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found this in the message log on a s390 system:
BUG kmalloc-192 (Not tainted): Poison overwritten
Disabling lock debugging due to kernel taint
INFO: 0x00000000684761f4-0x00000000684761f7. First byte 0xff instead of 0x6b
INFO: Allocated in call_usermodehelper_setup+0x70/0x128 age=71 cpu=2 pid=648
__slab_alloc.isra.47.constprop.56+0x5f6/0x658
kmem_cache_alloc_trace+0x106/0x408
call_usermodehelper_setup+0x70/0x128
call_usermodehelper+0x62/0x90
cgroup_release_agent+0x178/0x1c0
process_one_work+0x36e/0x680
worker_thread+0x2f0/0x4f8
kthread+0x10a/0x120
kernel_thread_starter+0x6/0xc
kernel_thread_starter+0x0/0xc
INFO: Freed in call_usermodehelper_exec+0x110/0x1b8 age=71 cpu=2 pid=648
__slab_free+0x94/0x560
kfree+0x364/0x3e0
call_usermodehelper_exec+0x110/0x1b8
cgroup_release_agent+0x178/0x1c0
process_one_work+0x36e/0x680
worker_thread+0x2f0/0x4f8
kthread+0x10a/0x120
kernel_thread_starter+0x6/0xc
kernel_thread_starter+0x0/0xc
There is a use-after-free bug on the subprocess_info structure allocated
by the user mode helper. In case do_execve() returns with an error
____call_usermodehelper() stores the error code to sub_info->retval, but
sub_info can already have been freed.
Regarding UMH_NO_WAIT, the sub_info structure can be freed by
__call_usermodehelper() before the worker thread returns from
do_execve(), allowing memory corruption when do_execve() failed after
exec_mmap() is called.
Regarding UMH_WAIT_EXEC, the call to umh_complete() allows
call_usermodehelper_exec() to continue which then frees sub_info.
To fix this race the code needs to make sure that the call to
call_usermodehelper_freeinfo() is always done after the last store to
sub_info->retval.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for RTC device inside PM8941 PMIC. The RTC in this PMIC
have two register spaces. Thus the rtc-pm8xxx is slightly reworked to
reflect these differences.
The register set for different PMIC chips are selected on DT compatible
string base.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify and fix locking in pm8xxx_rtc_set_time()]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an anonymous mapping is not allowed to fault thp memory and then
madvise(MADV_HUGEPAGE) is used after fault, khugepaged will never
collapse this memory into thp memory.
This occurs because the madvise(2) handler for thp, hugepage_madvise(),
clears VM_NOHUGEPAGE on the stack and it isn't stored in vma->vm_flags
until the final action of madvise_behavior(). This causes the
khugepaged_enter_vma_merge() to be a no-op in hugepage_madvise() when
the vma had previously had VM_NOHUGEPAGE set.
Fix this by passing the correct vma flags to the khugepaged mm slot
handler. There's no chance khugepaged can run on this vma until after
madvise_behavior() returns since we hold mm->mmap_sem.
It would be possible to clear VM_NOHUGEPAGE directly from vma->vm_flags
in hugepage_advise(), but I didn't want to introduce special case
behavior into madvise_behavior(). I think it's best to just let it
always set vma->vm_flags itself.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Suleiman Souhlal <suleiman@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compound page should be freed by put_page() or free_pages() with correct
order. Not doing so will cause tail pages leaked.
The compound order can be obtained by compound_order() or use
HPAGE_PMD_ORDER in our case. Some people would argue the latter is
faster but I prefer the former which is more general.
This bug was observed not just on our servers (the worst case we saw is
11G leaked on a 48G machine) but also on our workstations running Ubuntu
based distro.
$ cat /proc/vmstat | grep thp_zero_page_alloc
thp_zero_page_alloc 55
thp_zero_page_alloc_failed 0
This means there is (thp_zero_page_alloc - 1) * (2M - 4K) memory leaked.
Fixes: 97ae17497e ("thp: implement refcounting for huge zero page")
Signed-off-by: Yu Zhao <yuzhao@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: David Rientjes <rientjes@google.com>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: <stable@vger.kernel.org> [3.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During file system stress testing on 3.10 and 3.12 based kernels, the
umount command occasionally hung in fsnotify_unmount_inodes in the
section of code:
spin_lock(&inode->i_lock);
if (inode->i_state & (I_FREEING|I_WILL_FREE|I_NEW)) {
spin_unlock(&inode->i_lock);
continue;
}
As this section of code holds the global inode_sb_list_lock, eventually
the system hangs trying to acquire the lock.
Multiple crash dumps showed:
The inode->i_state == 0x60 and i_count == 0 and i_sb_list would point
back at itself. As this is not the value of list upon entry to the
function, the kernel never exits the loop.
To help narrow down problem, the call to list_del_init in
inode_sb_list_del was changed to list_del. This poisons the pointers in
the i_sb_list and causes a kernel to panic if it transverse a freed
inode.
Subsequent stress testing paniced in fsnotify_unmount_inodes at the
bottom of the list_for_each_entry_safe loop showing next_i had become
free.
We believe the root cause of the problem is that next_i is being freed
during the window of time that the list_for_each_entry_safe loop
temporarily releases inode_sb_list_lock to call fsnotify and
fsnotify_inode_delete.
The code in fsnotify_unmount_inodes attempts to prevent the freeing of
inode and next_i by calling __iget. However, the code doesn't do the
__iget call on next_i
if i_count == 0 or
if i_state & (I_FREEING | I_WILL_FREE)
The patch addresses this issue by advancing next_i in the above two cases
until we either find a next_i which we can __iget or we reach the end of
the list. This makes the handling of next_i more closely match the
handling of the variable "inode."
The time to reproduce the hang is highly variable (from hours to days.) We
ran the stress test on a 3.10 kernel with the proposed patch for a week
without failure.
During list_for_each_entry_safe, next_i is becoming free causing
the loop to never terminate. Advance next_i in those cases where
__iget is not done.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hp.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ken Helias <kenhelias@firemail.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit edc2ca6124 ("mm, compaction: move pageblock checks up from
isolate_migratepages_range()") commonizes isolate_migratepages variants
and make them use isolate_migratepages_block().
isolate_migratepages_block() could stop the execution when enough pages
are isolated, but, there is no code in isolate_migratepages_range() to
handle this case. In the result, even if isolate_migratepages_block()
returns prematurely without checking all pages in the range,
isolate_migratepages_block() is called repeately on the following
pageblock and some pages in the previous range are skipped to check.
Then, CMA is failed frequently due to this fact.
To fix this problem, this patch let isolate_migratepages_range() know
the situation that enough pages are isolated and stop the isolation in
that case.
Note that isolate_migratepages() has no such problem, because, it always
stops the isolation after just one call of isolate_migratepages_block().
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ff7ee93f47 ("cgroup/kmemleak: Annotate alloc_page() for cgroup
allocations") introduces kmemleak_alloc() for alloc_page_cgroup(), but
corresponding kmemleak_free() is missing, which makes kmemleak be
wrongly disabled after memory offlining. Log is pasted at the end of
this commit message.
This patch add kmemleak_free() into free_page_cgroup(). During page
offlining, this patch removes corresponding entries in kmemleak rbtree.
After that, the freed memory can be allocated again by other subsystems
without killing kmemleak.
bash # for x in 1 2 3 4; do echo offline > /sys/devices/system/memory/memory$x/state ; sleep 1; done ; dmesg | grep leak
Offlined Pages 32768
kmemleak: Cannot insert 0xffff880016969000 into the object search tree (overlaps existing)
CPU: 0 PID: 412 Comm: sleep Not tainted 3.17.0-rc5+ #86
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x46/0x58
create_object+0x266/0x2c0
kmemleak_alloc+0x26/0x50
kmem_cache_alloc+0xd3/0x160
__sigqueue_alloc+0x49/0xd0
__send_signal+0xcb/0x410
send_signal+0x45/0x90
__group_send_sig_info+0x13/0x20
do_notify_parent+0x1bb/0x260
do_exit+0x767/0xa40
do_group_exit+0x44/0xa0
SyS_exit_group+0x17/0x20
system_call_fastpath+0x16/0x1b
kmemleak: Kernel memory leak detector disabled
kmemleak: Object 0xffff880016900000 (size 524288):
kmemleak: comm "swapper/0", pid 0, jiffies 4294667296
kmemleak: min_count = 0
kmemleak: count = 0
kmemleak: flags = 0x1
kmemleak: checksum = 0
kmemleak: backtrace:
log_early+0x63/0x77
kmemleak_alloc+0x4b/0x50
init_section_page_cgroup+0x7f/0xf5
page_cgroup_init+0xc5/0xd0
start_kernel+0x333/0x408
x86_64_start_reservations+0x2a/0x2c
x86_64_start_kernel+0xf5/0xfc
Fixes: ff7ee93f47 (cgroup/kmemleak: Annotate alloc_page() for cgroup allocations)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@vger.kernel.org> [3.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
consolidated the lookup of CPU DAIs and CODEC DAIs into a single function.
When matching a component by name for CODEC DAIs the code previous to the
patch compared the name in the DAI link table with component->name. For CPU
DAIs the code compared to dev_name(component->dev). The newly introduced
function ended up using the later as well.
For most components dev_name(component->dev) and component->name are the
same. The main notable exception are I2C devices where the driver name and
the device name are concatenated to form the component name. By using
dev_name(component->dev) instead of component->name the patch broke the
matching of I2C CODECs by name.
This patch restores the original behavior by using component->name instead
of dev_name(component->dev). This will be safe even for CPU DAIs since for
CPU DAIs both are the same.
Fixes: 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WARN_ON in inet_evict_bucket can be triggered by a valid case:
inet_frag_kill and inet_evict_bucket can be running in parallel on the
same queue which means that there has been at least one more ref added
by a previous inet_frag_find call, but inet_frag_kill can delete the
timer before inet_evict_bucket which will cause the WARN_ON() there to
trigger since we'll have refcnt!=1. Now, this case is valid because the
queue is being "killed" for some reason (removed from the chain list and
its timer deleted) so it will get destroyed in the end by one of the
inet_frag_put() calls which reaches 0 i.e. refcnt is still valid.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the evictor is running it adds some chosen frags to a local list to
be evicted once the chain lock has been released but at the same time
the *frag_queue can be running for some of the same queues and it
may call inet_frag_kill which will wait on the chain lock and
will then delete the queue from the wrong list since it was added in the
eviction one. The fix is simple - check if the queue has the evict flag
set under the chain lock before deleting it, this is safe because the
evict flag is set only under that lock and having the flag set also means
that the queue has been detached from the chain list, so no need to delete
it again.
An important note to make is that we're safe w.r.t refcnt because
inet_frag_kill and inet_evict_bucket will sync on the del_timer operation
where only one of the two can succeed (or if the timer is executing -
none of them), the cases are:
1. inet_frag_kill succeeds in del_timer
- then the timer ref is removed, but inet_evict_bucket will not add
this queue to its expire list but will restart eviction in that chain
2. inet_evict_bucket succeeds in del_timer
- then the timer ref is kept until the evictor "expires" the queue, but
inet_frag_kill will remove the initial ref and will set
INET_FRAG_COMPLETE which will make the frag_expire fn just to remove
its ref.
In the end all of the queue users will do an inet_frag_put and the one
that reaches 0 will free it. The refcount balance should be okay.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Tested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're moving omaps to use device tree based booting and already have
omap2, omap4, omap5, am335x and am437x booting in device tree only
mode.
Only omap3 still has legacy booting still around and we really want
to make that device tree only. So let's add a warning about deprecated
legacy booting so we get people to upgrade their boards to use device
tree based booting and find out about any remaining issues.
Note that for most boards we already have the .dts file and those can
be booted with without changing the bootloader using the appended
DTB mode.
Acked-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we need to have BCH enabled to get NAND
working and to avoid getting:
nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled
Signed-off-by: Tony Lindgren <tony@atomide.com>
1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current kernel. This contains:
- Two error handling fixes from Jan Kara. One for null_blk on
failure to add a device, and the other for the block/scsi_ioctl
SCSI_IOCTL_SEND_COMMAND fixing up the error jump point.
- A commit added in the merge window for the bio integrity bits
unfortunately disabled merging for all requests if
CONFIG_BLK_DEV_INTEGRITY wasn't set. Reverse the logic, so that
integrity checking wont disallow merges when not enabled.
- A fix from Ming Lei for merging and generating too many segments.
This caused a BUG in virtio_blk.
- Two error handling printk() fixups from Robert Elliott, improving
the information given when we rate limit.
- Error handling fixup on elevator_init() failure from Sudip
Mukherjee.
- A fix from Tony Battersby, fixing up a memory leak in the
scatterlist handling with scsi-mq"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Fix merge logic when CONFIG_BLK_DEV_INTEGRITY is not defined
lib/scatterlist: fix memory leak with scsi-mq
block: fix wrong error return in elevator_init()
scsi: Fix error handling in SCSI_IOCTL_SEND_COMMAND
null_blk: Cleanup error recovery in null_add_dev()
blk-merge: recaculate segment if it isn't less than max segments
fs: clarify rate limit suppressed buffer I/O errors
fs: merge I/O error prints into one line
Commit 48cf06bc5f ("dm raid: add discard support for RAID levels 4, 5
and 6") did not properly handle missing metadata device(s). A failing
read of the superblock causes the metadata and data devices to be
removed from the dev array in struct raid_set, setting references to
both devices to NULL. configure_discard_support() nonetheless tries to
access the data dev unconditionally causing an oops.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull HID fixes from Jiri Kosina:
- workarounds for a couple of misbehaving Elan Touchscreens, by Adel
Gadllah
- fix for TransducerSerialNumber field implementation, by Jason Gerecke
- a couple of new HID usages (added by HUT), by Olivier Gay
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: input: Fix TransducerSerialNumber implementation
HID: add keyboard input assist hid usages
HID: usbhid: enable always-poll quirk for Elan Touchscreen 016f
HID: usbhid: enable always-poll quirk for Elan Touchscreen 009b
Replaced repetive Device ID's which got added in commit b961f9a488
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Integrity subsystem fix from James Morris:
"These changes fix a bug in xattr handling, where the evm and ima
inode_setxattr() functions do not check for empty xattrs being passed
from userspace (leading to user-triggerable null pointer
dereferences)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
evm: check xattr value length and type in evm_inode_setxattr()
ima: check xattr value length and type in the ima_inode_setxattr()
Pull powerpc updates from Michael Ellerman:
"There's some bug fixes or cleanups to facilitate fixes, a MAINTAINERS
update, and a new syscall (bpf)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/numa: ensure per-cpu NUMA mappings are correct on topology update
powerpc/numa: use cached value of update->cpu in update_cpu_topology
cxl: Fix PSL error due to duplicate segment table entries
powerpc/mm: Use appropriate ESID mask in copro_calculate_slb()
cxl: Refactor cxl_load_segment() and find_free_sste()
cxl: Disable secondary hash in segment table
Revert "powerpc/powernv: Fix endian bug in LPC bus debugfs accessors"
powernv: Use _GLOBAL_TOC for opal wrappers
powerpc: Wire up sys_bpf() syscall
MAINTAINERS: nx-842 driver maintainer change
powerpc/mm: Remove redundant #if case
powerpc/mm: Fix build error with hugetlfs disabled
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a
very significant drop in networking performance. The test were
conducted on an OpenBlocks A7 board. Without this patch, the outgoing
performance measured with iperf are:
- highmem OFF, TSO OFF 544 Mbit/s
- highmem OFF, TSO ON 942 Mbit/s
- highmem ON, TSO OFF 306 Mbit/s
- highmem ON, TSO ON 246 Mbit/s
On this Kirkwood platform, the L2 cache is a Feroceon cache, and with
this cache, all the range operations have to be done on virtual
addresses and not physical addresses. Therefore, whenever
CONFIG_HIGHMEM is enabled, the cache maintenance operations call
kmap_atomic_pfn() and kunmap_atomic().
However, kmap_atomic_pfn() does not implement the same fast path for
non-highmem pages as the one implemented in kmap_atomic(), and this is
one of the reason for the performance drop. While this patch does not
fully restore the performances, it clearly improves them a lot:
without patch with patch
- highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s
- highmem ON, TSO ON 246 Mbit/s 434 Mbit/s
We're still far from the !CONFIG_HIGHMEM performances, but it does
improve a bit the situation.
Thanks a lot to Ezequiel Garcia and Gregory Clement for all the
testing work around this topic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King suggested [1]:
"I'd ask for one change. Please make all these messages start with
"L2C-310 OF" not "PL310 OF:". The device is described in ARM
documentation as a L2C-310 not PL310. (Also note the : is dropped
too - most of the other messages don't have the : either.)
The:
"PL310 OF: cache setting yield illegal associativity
PL310 OF: -1073346556 calculated, only 8 and 16 legal"
message could also be changed to something like:
"L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn"
[1] http://www.spinics.net/lists/arm-kernel/msg372776.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 513510ddba
(common: dma-mapping: introduce common remapping functions)
managed to end up with an extra return statement from the
original patch. Drop it.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Johan writes:
USB-serial fixes for v3.18-rc3
These updates remove two allocations of unused buffers from kobil_sct
and add some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
The calculation of "num_shader_engines" has a precedence bug because
the right shift happens before the mask, but this variable is never used
so we can just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For boards without a reset GPIO we skip the delay between enabling the
pcie_ref_clk and touching the RC registers for configuration. This hangs
the system if there isn't a proper delay to ensure the clocks are settled
in the DW PCIe core.
Also iMX6Q always needs an additional 10us delay to make sure the reset is
propagated through the core, as we don't have an explicitly controlled
reset input on this SoC.
This fixes a problem with 3fce0e882f ("PCI: imx6: Delay enabling
reference clock for SS until it stabilizes"): the kernel doesn't boot on
systems that don't pass the PCI GPIO reset in the DTB. This regression
affects mx6 nitrogen boards.
[bhelgaas: add regression info in changelog]
Fixes: 3fce0e882f ("PCI: imx6: Delay enabling reference clock for SS until it stabilizes")
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Richard Zhu <richard.zhu@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
It is reported that Samsung laptops that need to poll events are broken by
the following commit:
Commit 3afcf2ece4
Subject: ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
The behaviors of the 2 vendor firmwares are conflict:
1. Acer: OSPM shouldn't issue QR_EC unless SCI_EVT is set, firmware
automatically sets SCI_EVT as long as there is event queued up.
2. Samsung: OSPM should issue QR_EC whatever SCI_EVT is set, firmware
returns 0 when there is no event queued up.
This patch is a quick fix to distinguish the behaviors to make Acer
behavior only effective for Acer EC firmware so that the breakages on
Samsung EC firmware can be avoided.
Fixes: 3afcf2ece4 (ACPI / EC: Add support to disallow QR_EC to be issued ...)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
[ rjw : Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is reported that the following commit breaks Samsung hardware:
Commit: 558e4736f2.
Subject: ACPI / EC: Add support to disallow QR_EC to be issued before
completing previous QR_EC
Which means the Samsung behavior conflicts with the Acer behavior.
1. Samsung may behave like:
[ +event 1 ] SCI_EVT set
[ +event 2 ] SCI_EVT set
write QR_EC
read event
[ -event 1 ] SCI_EVT clear
Without the above commit, Samsung can work:
[ +event 1 ] SCI_EVT set
[ +event 2 ] SCI_EVT set
write QR_EC
CAN prepare next QR_EC as SCI_EVT=1
read event
[ -event 1 ] SCI_EVT clear
write QR_EC
read event
[ -event 2 ] SCI_EVT clear
With the above commit, Samsung cannot work:
[ +event 1 ] SCI_EVT set
[ +event 2 ] SCI_EVT set
write QR_EC
read event
[ -event 1 ] SCI_EVT clear
CANNOT prepare next QR_EC as SCI_EVT=0
2. Acer may behave like:
[ +event 1 ] SCI_EVT set
[ +event 2 ]
write QR_EC
read event
[ -event 1 ] SCI_EVT clear
[ +event 2 ] SCI_EVT set
Without the above commit, Acer cannot work when there is only 1 event:
[ +event 1 ] SCI_EVT set
write QR_EC
can prepared next QR_EC as SCI_EVT=1
read event
[ -event 1 ] SCI_EVT clear
CANNOT write QR_EC as SCI_EVT=0
With the above commit, Acer can work:
[ +event 1 ] SCI_EVT set
[ +event 2 ]
write QR_EC
read event
[ -event 1 ] SCI_EVT set
can prepare next QR_EC because SCI_EVT=0
CAN write QR_EC as SCI_EVT=1
Since Acer can also work with only the following commit applied:
Commit: 3afcf2ece4
Subject: ACPI / EC: Add support to disallow QR_EC to be issued when
SCI_EVT isn't set
commit 558e4736f2 can be reverted.
Fixes: 558e4736f2 (ACPI / EC: Add support to disallow QR_EC to be issued ...)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Due to the time it takes to process the beacon that started the CSA
process, we may be late for the switch if we try to reach exactly
beacon 0. To avoid that, use count - 1 when calculating the switch time.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used. This applies both to beacons and to probe
responses.
In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead. This was
causing us to use the same offset as before the switch.
Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset. Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CMI8888 shows the stuttering playback when the snooping is disabled
on the audio buffer. Meanwhile, we've got reports that CORB/RIRB
doesn't work in the snooped mode. So, as a compromise, disable the
snoop only for CORB/RIRB and enable the snoop for the stream buffers.
The resultant patch became a bit ugly, unfortunately, but we still can
live with it.
Reported-and-tested-by: Geoffrey McRae <geoff@spacevs.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reported-by text says you have to ask for permission, but that
should only be if the bug was reported in private. These days the
standard is to always give reported-by credit or it's considered a bit
rude.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Description of regulators should generally be optional so if there is no
DT node for the regulators container then we shouldn't print an error
message. Lower the severity of the message to debug level (it might help
someone work out what went wrong) and while we're at it say what we were
looking for.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
After kernel 3.7 (commit b4b8f770eb),
/proc/cpuinfo replaces 'Processor' to 'model name'.
This patch makes CPUINFO_PROC to an array and provides two choices for
ARM, makes it compatible for different kernel version.
v1 -> v2: minor changes as suggested by Namhyung Kim:
- Doesn't pass @h and @evlist to __write_cpudesc;
- Coding style fix.
v2 -> v3:
- Rebase:
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux.git perf/core
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1414115126-7479-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Emulation of code that is 14 bytes to the segment limit or closer
(e.g. RIP = 0xFFFFFFF2 after reset) is broken because we try to read as
many as 15 bytes from the beginning of the instruction, and __linearize
fails when the passed (address, size) pair reaches out of the segment.
To fix this, let __linearize return the maximum accessible size (clamped
to 2^32-1) for usage in __do_insn_fetch_bytes, and avoid the limit check
by passing zero for the desired size.
For expand-down segments, __linearize is performing a redundant check.
(u32)(addr.ea + size - 1) <= lim can only happen if addr.ea is close
to 4GB; in this case, addr.ea + size - 1 will also fail the check against
the upper bound of the segment (which is provided by the D/B bit).
After eliminating the redundant check, it is simple to compute
the *max_size for expand-down segments too.
Now that the limit check is done in __do_insn_fetch_bytes, we want
to inject a general protection fault there if size < op_size (like
__linearize would have done), instead of just aborting.
This fixes booting Tiano Core from emulated flash with EPT disabled.
Cc: stable@vger.kernel.org
Fixes: 719d5a9b24
Reported-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error code for #GP and #SS is zero when the segment is used to
access an operand or an instruction. It is only non-zero when
a segment register is being loaded; for limit checks this means
cases such as:
* for #GP, when RIP is beyond the limit on a far call (before the first
instruction is executed). We do not implement this check, but it
would be in em_jmp_far/em_call_far.
* for #SS, if the new stack overflows during an inter-privilege-level
call to a non-conforming code segment. We do not implement stack
switching at all.
So use an error code of zero.
Reviewed-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit f3354ab674 ("ARM: 8169/1: l2c: parse cache properties from
ePAPR definitions") the following error is seen on imx6q:
[ 0.000000] PL310 OF: cache setting yield illegal associativity
[ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal
As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized.
To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mvm->cur_ucode wasn't set before we actually load the
firmware. This caused issues when we boot in RFKILL since
we get an RFKILL interrupt upon boot even before we load
any firmware.
This leads to issues since iwl_mvm_set_hw_rfkill_state
(the RFKILL interrupts handler in mvm) relies on this
variable.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These patches:
86a349a28b ("perf/x86/intel: Add Broadwell core support")
c46e665f03 ("perf/x86: Add INST_RETIRED.ALL workarounds")
fdda3c4aac ("perf/x86/intel: Use Broadwell cache event list for Haswell")
introduced magic constants and unexplained changes:
https://lkml.org/lkml/2014/10/28/1128https://lkml.org/lkml/2014/10/27/325https://lkml.org/lkml/2014/8/27/546https://lkml.org/lkml/2014/10/28/546
Peter Zijlstra has attempted to help out, to clean up the mess:
https://lkml.org/lkml/2014/10/28/543
But has not received helpful and constructive replies which makes
me doubt wether it can all be finished in time until v3.18 is
released.
Despite various review feedback the author (Andi Kleen) has answered
only few of the review questions and has generally been uncooperative,
only giving replies when prompted repeatedly, and only giving minimal
answers instead of constructively explaining and helping along the effort.
That kind of behavior is not acceptable.
There's also a boot crash on Intel E5-1630 v3 CPUs reported for another
commit from Andi Kleen:
e735b9db12 ("perf/x86/intel/uncore: Add Haswell-EP uncore support")
https://lkml.org/lkml/2014/10/22/730
Which is not yet resolved. The uncore driver is independent in theory,
but the crash makes me worry about how well all these patches were
tested and makes me uneasy about the level of interminging that the
Broadwell and Haswell code has received by the commits above.
As a first step to resolve the mess revert the Broadwell client commits
back to the v3.17 version, before we run out of time and problematic
code hits a stable upstream kernel.
( If the Haswell-EP crash is not resolved via a simple fix then we'll have
to revert the Haswell-EP uncore driver as well. )
The Broadwell client series has to be submitted in a clean fashion, with
single, well documented changes per patch. If they are submitted in time
and are accepted during review then they can possibly go into v3.19 but
will need additional scrutiny due to the rocky history of this patch set.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: eranian@google.com
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1409683455-29168-3-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The commit which introduced TransducerSerialNumber (368c966) is missing
two crucial implementation details. Firstly, the commit does not set the
type/code/bit/max fields as expected later down the code which can cause
the driver to crash when a tablet with this usage is connected. Secondly,
the call to 'set_bit' causes MSC_PULSELED to be sent instead of the
expected MSC_SERIAL. This commit addreses both issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As a follow-up to commit 6cab7a37f5 ("staging: comedi: (regression)
channel list must be set for COMEDI_CMD ioctl"), Hartley Sweeten pointed
out another couple of bugs stemming from commit 6cab7a37f5 ("staging:
comedi: comedi_fops: introduce __comedi_get_user_chanlist()").
Firstly, `do_cmdtest_ioctl()` never frees the kernel copy of the user
chanlist allocated by `__comedi_get_user_chanlist()`, so that memory is
leaked. Fix it by freeing the allocated kernel memory pointed to by
`cmd.chanlist` before that pointer is overwritten with its original
pointer to user memory before `cmd` is copied back to user-space.
Secondly, if `__comedi_get_user_chanlist()` returns an error,
`cmd->chanlist` is left unchanged and in fact will be a pointer to user
memory. This causes `do_cmd_ioctl()` to `goto cleanup` and call
`do_become_nonbusy()` which would attempt to free the memory pointed to
by the user-space pointer. Fix it by setting `cmd->chanlist` to NULL at
the start of `__comedi_get_user_chanlist()`.
Fixes: c6cd0eefb2 ("staging: comedi: comedi_fops: introduce __comedi_get_user_chanlist()")
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y: 6cab7a37f5
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A merge conflict between commits
fbfd9c8a17 ("staging: comedi:
addi_apci_3120: use dma_alloc_coherent()") and
aff5b1f8eb ("staging: comedi: remove
comedi_fc module") left the COMEDI_ADDI_APCI_3120 config option
depending on VIRT_TO_BUS when it no longer needs to do so. The
dependency was removed by the first commit and accidentally reinstated
by the second commit. Remove the dependency again.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the `COMEDI_LOCK`, `COMEDI_UNLOCK`, `COMEDI_CANCEL`, and
`COMEDI_POLL` ioctls the third argument is a comedi subdevice number.
This is passed as an `unsigned long`, but when it is passed down to the
ioctl command-specific handler functions `do_lock_ioctl()`,
`do_unlock_ioctl()`, `do_cancel_ioctl()`, and `do_poll_ioctl()`, the
value has been narrowed to an `unsigned int`. Pass through the argument
as an `unsigned long` to avoid truncating the value on 64-bit
architectures.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4eaf99bead switched to returning bool and as a result reversed
the logic of the integrity merge checks. However, the empty stubs used
when the block integrity code is compiled out were still returning
0. Make these stubs return "true".
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Tested-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Even if CMA is disabled, the for_each_memblock macro expands
to run reserve_bootmem once. Hence, reserve_bootmem attempts to
reserve location 0 of size 0.
Add a check to avoid that.
Issue was highlighted during testing with EVA enabled.
resrve_bootmem used to exit gracefully when passed arguments to
reserve 0 size location at 0 without EVA.
But with EVA enabled, macros would point to different addresses
and the code would trigger a BUG.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Tested-by: Markos Chandras <markos.chandras@imgtec.com>
Tested-by: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8231/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We received a report of warning in kernel/sched/core.c where the sched
group was NULL on an LPAR after a topology update. This seems to occur
because after the topology update has moved the CPUs, cpu_to_node is
returning the old value still, which ends up breaking the consistency of
the NUMA topology in the per-cpu maps. Ensure that we update the per-cpu
fields when we re-map CPUs.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There isn't any need to keep referring to update->cpu, as we've already
checked cpu == update->cpu at this point.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In an overlay directory that shadows an empty lower directory, say
/mnt/a/empty102, do:
touch /mnt/a/empty102/x
unlink /mnt/a/empty102/x
rmdir /mnt/a/empty102
It's actually harmless, but needs another level of nesting between
I_MUTEX_CHILD and I_MUTEX_NORMAL.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ovl_cache_entry.name is now an array not a pointer, so it makes no sense
test for it being NULL.
Detected by coverity.
From: Miklos Szeredi <mszeredi@suse.cz>
Fixes: 68bf861107 ("overlayfs: make ovl_cache_entry->name an array instead of
+pointer")
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
make sure that
a) all stores done by opening struct file don't leak past storing
the reference in od->upperfile
b) the lockless side has read dependency barrier
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Although rcu_dereference() and friends can be used in situations where
object lifetimes are being managed by something other than RCU, the
resulting sparse and lockdep-RCU noise can be annoying. This commit
therefore supplies a lockless_dereference(), which provides the
protection for dereferences without the RCU-related debugging noise.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since commit cd678fce42 ("switch logger to ->write_iter()"), any
attempt to write to the log results in the log data being written over
its own metadata, thus rendering the log unreadable.
The problem was first detected when I ran an Android userspace on the
v3.18-rc1 kernel. However the issue can also be observed with a
non-Android userspace by using echo/cat to write to/from /dev/log_main .
This patch resolves the problem by using a temporary to track the status
of not-yet-committed writes to the log buffer.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Olivier Blin says:
====================
cdc-ether: handle promiscuous mode
Since kernel 3.16, my Lenovo USB network adapters (RTL8153) using
cdc-ether are not working anymore in a bridge.
This is due to commit c472ab68ad, which
resets the packet filter when the device is bound.
The default packet filter set by cdc-ether does not include
promiscuous, while the adapter seemed to have promiscuous enabled by
default.
This patch series allows to support promiscuous mode for cdc-ether, by
hooking into set_rx_mode.
Incidentally, maybe this device should be handled by the r8152 driver,
but this patch series is still nice for other adapters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68ad
(cdc-ether: clean packet filter upon probe).
It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the set_rx_mode callback.
Also move a comment about multicast filtering in this new function.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of the bulkstat code left a small landmine in
the code. If a inobt read fails, then the tree walk is aborted and
returns without releasing the AGI buffer or freeing the cursor. This
can lead to a subsequent bulkstat call hanging trying to grab the
AGI buffer again.
cc: <stable@vger.kernel.org>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This patch enables configs required to boot IFC6540 board with atleast a
serial console.
Without this patch there is no serial console.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Florian Fainelli says:
====================
net: systemport: RX path and suspend fixes
These two patches fix a race condition where we have our RX interrupts
enabled, but not NAPI for the RX path, and the second patch fixes an
issue for packets stuck in RX fifo during a suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.
This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.
Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When arch/arm/mach-ixp4xx/common-pci.c is compiled, two warnings
occur:
arch/arm/mach-ixp4xx/include/mach/io.h:144: warning: passing argument 1 of '__raw_readb' makes pointer from integer without a cast
arch/arm/mach-ixp4xx/include/mach/io.h:79: warning: passing argument 2 of '__raw_writeb' makes pointer from integer without a cast
Both functions expect an 'volatile void __iomem *' but get an u32.
The 'u32 addr' variable is initialized with the address of an
'volatile void __iomem *' pointer. Passing the pointer
directly, avoids the warning and semantics are preserved.
This warning was found with vampyr.
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix kernel-doc warning in <linux/skbuff.h> by making both headers_start
and headers_end private fields.
Warning(..//include/linux/skbuff.h:654): No description found for parameter 'headers_end[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a race that can lead us to miss skinny extent items in the function
btrfs_lookup_extent_info() when the skinny metadata feature is enabled.
So basically the sequence of steps is:
1) We search in the extent tree for the skinny extent, which returns > 0
(not found);
2) We check the previous item in the returned leaf for a non-skinny extent,
and we don't find it;
3) Because we didn't find the non-skinny extent in step 2), we release our
path to search the extent tree again, but this time for a non-skinny
extent key;
4) Right after we released our path in step 3), a skinny extent was inserted
in the extent tree (delayed refs were run) - our second extent tree search
will miss it, because it's not looking for a skinny extent;
5) After the second search returned (with ret > 0), we look for any delayed
ref for our extent's bytenr (and we do it while holding a read lock on the
leaf), but we won't find any, as such delayed ref had just run and completed
after we released out path in step 3) before doing the second search.
Fix this by removing completely the path release and re-search logic. This is
safe, because if we seach for a metadata item and we don't find it, we have the
guarantee that the returned leaf is the one where the item would be inserted,
and so path->slots[0] > 0 and path->slots[0] - 1 must be the slot where the
non-skinny extent item is if it exists. The only case where path->slots[0] is
zero is when there are no smaller keys in the tree (i.e. no left siblings for
our leaf), in which case the re-search logic isn't needed as well.
This race has been present since the introduction of skinny metadata (change
3173a18f70).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
It is not guaranteed to that srp_sq_size is supported
by the HCA. So if we failed to create the QP with ENOMEM,
try with a smaller srp_sq_size. Keep it up until we hit
MIN_SRPT_SQ_SIZE, then fail the connection.
Reported-by: Mark Lehrer <lehrer@gmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The fact that a target is published on the any address has no bearing on
which port(s) it is published. SendTargets should always send the
portal's port, not the port used for discovery.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where individual vhost-scsi configfs endpoint
groups can be removed from below while active exports to QEMU userspace
still exist, resulting in an OOPs.
It adds a configfs_depend_item() in vhost_scsi_set_endpoint() to obtain
an explicit dependency on se_tpg->tpg_group in order to prevent individual
vhost-scsi WWPN endpoints from being released via normal configfs methods
while an QEMU ioctl reference still exists.
Also, add matching configfs_undepend_item() in vhost_scsi_clear_endpoint()
to release the dependency, once QEMU's reference to the individual group
at /sys/kernel/config/target/vhost/$WWPN/$TPGT is released.
(Fix up vhost_scsi_clear_endpoint() error path - DanC)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an initiator sends a zero-length command (e.g. TEST UNIT READY) but
sets the transfer direction in the transport layer to indicate a
data-out phase, we still shouldn't try to transfer data. At best it's
a NOP, and depending on the transport, we might crash on an
uninitialized sg list.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org> # 3.1
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull two nfsd fixes from Bruce Fields:
"One regression from the 3.16 xdr rewrite, one an older bug exposed by
a separate bug in the client's new SEEK code"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix crash on unknown operation number
nfsd4: fix response size estimation for OP_SEQUENCE
Pull ftrace trampoline accounting fixes from Steven Rostedt:
"Adding the new code for 3.19, I discovered a couple of minor bugs with
the accounting of the ftrace_ops trampoline logic.
One was that the old hash was not updated before calling the modify
code for an ftrace_ops. The second bug was what let the first bug go
unnoticed, as the update would check the current hash for all
ftrace_ops (where it should only check the old hash for modified
ones). This let things work when only one ftrace_ops was registered
to a function, but could break if more than one was registered
depending on the order of the look ups.
The worse thing that can happen if this bug triggers is that the
ftrace self checks would find an anomaly and shut itself down"
* tag 'trace-fixes-v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix checking of trampoline ftrace_ops in finding trampoline
ftrace: Set ops->old_hash on modifying what an ops hooks to
Commit 35ce7f29a4 (rcu: Create rcuo kthreads only for onlined CPUs)
avoids creating rcuo kthreads for CPUs that never come online. This
fixes a bug in many instances of firmware: Instead of lying about their
age, these systems instead lie about the number of CPUs that they have.
Before commit 35ce7f29a4, this could result in huge numbers of useless
rcuo kthreads being created.
It appears that experience indicates that I should have told the
people suffering from this problem to fix their broken firmware, but
I instead produced what turned out to be a partial fix. The missing
piece supplied by this commit makes sure that rcu_barrier() knows not to
post callbacks for no-CBs CPUs that have not yet come online, because
otherwise rcu_barrier() will hang on systems having firmware that lies
about the number of CPUs.
It is tempting to simply have rcu_barrier() refuse to post a callback on
any no-CBs CPU that does not have an rcuo kthread. This unfortunately
does not work because rcu_barrier() is required to wait for all pending
callbacks. It is therefore required to wait even for those callbacks
that cannot possibly be invoked. Even if doing so hangs the system.
Given that posting a callback to a no-CBs CPU that does not yet have an
rcuo kthread can hang rcu_barrier(), It is tempting to report an error
in this case. Unfortunately, this will result in false positives at
boot time, when it is perfectly legal to post callbacks to the boot CPU
before the scheduler has started, in other words, before it is legal
to invoke rcu_barrier().
So this commit instead has rcu_barrier() avoid posting callbacks to
CPUs having neither rcuo kthread nor pending callbacks, and has it
complain bitterly if it finds CPUs having no rcuo kthread but some
pending callbacks. And when rcu_barrier() does find CPUs having no rcuo
kthread but pending callbacks, as noted earlier, it has no choice but
to hang indefinitely.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Reported-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Eric B Munson <emunson@akamai.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Eric B Munson <emunson@akamai.com>
Tested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Tested-by: Yanko Kaneti <yaneti@declera.com>
Tested-by: Kevin Fenzi <kevin@scrye.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Pull ARM fixes from Russell King:
"A couple of ARM fixes.
We fix some printk formats for ptrdiff_t quantities which cause GCC
4.9 to complain, and we also blacklist known buggy GCC 4.8.x compilers
as their miscompilation is serious enough to cause filesystem
corruption, even through many distros have fixed their versions"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix some printk formats
ARM: Blacklist GCC 4.8.0 to GCC 4.8.2 - PR58854
When unmapping a range of pages in zap_pte_range, the page being
unmapped is added to an mmu_gather_batch structure for asynchronous
freeing. If we run out of space in the batch structure before the range
has been completely unmapped, then we break out of the loop, force a
TLB flush and free the pages that we have batched so far. If there are
further pages to unmap, then we resume the loop where we left off.
Unfortunately, we forget to update addr when we break out of the loop,
which causes us to truncate the range being invalidated as the end
address is exclusive. When we re-enter the loop at the same address, the
page has already been freed and the pte_present test will fail, meaning
that we do not reconsider the address for invalidation.
This patch fixes the problem by incrementing addr by the PAGE_SIZE
before breaking out of the loop on batch failure.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-28
Please pull this batch of fixes intended for the 3.18 stream!
For the mac80211 bits, Johannes says:
"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
For the iwlwifi bits, Emmanuel says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
In addition...
Felix Fietkau adds a couple of ath code fixes related to regulatory
rule enforcement.
Hauke Mehrtens fixes a build break with bcma when CONFIG_OF_ADDRESS
is not set.
Karsten Wiese provides a trio of minor fixes for rtl8192cu.
Kees Cook prevents a potential information leak in rtlwifi.
Larry Finger also brings a trio of minor fixes for rtlwifi.
Rafał Miłecki adds a device ID to the bcma bus driver.
Rickard Strandqvist offers some strn* -> strl* changes in brcmfmac
to eliminate non-terminated string issues.
Sujith Manoharan avoids some ath9k stalls by enabling HW queue control
only for MCC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
DSA tagging mismatches
The second patch is a fix, which should be applied to -rc. It is
possible to get a DSA configuration which does not work. The patch
stops this happening.
The first patch detects this situation, and errors out the probe of
DSA, making it more obvious something is wrong. It is not required to
apply it -rc.
v2 fixes the use case pointed out by Florian, that a switch driver
may use DSA_TAG_PROTO_NONE which the patch did not correctly handle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.
Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f2725394 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a mismatch between enabled tagging protocols and the
protocol the switch supports, error out, rather than continue with a
situation which is unlikely to work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
cc: alexander.h.duyck@intel.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
psmouse_reconnect() will not be called if psmouse driver is not bound to
the serio port, so there is no point in checking that. Also, as coded, it
introduces potential NULL dereference in psmouse_dbg() in case psmouse is
indeed NULL. Let's just remove it.
Detected by Coverity: CID 146528
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I believe the intent of the code was to drop oldest bytes from the queue,
not the latest if we drop one byte and both latest and some oldest of we
are dropping more than one.
Acked-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Coverity pointed out that at return point error is always 0 so the
conditional is not needed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Excessive debug messages might cause timing issues that prevent correct
usb enumeration. This patch hides information about USB bus reset to let
driver enumerate fast enough to avoid making host angry. This fixes
endless enumeration and usb reset loop observed with some Linux hosts.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prctl test code in Documentation/ tries to show how to
use a call that only makes sense on x86. Restrict it there
so that other platforms don't try to call asm("rdtsc").
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In compat mode, we copy each field of snd_pcm_status struct but don't
touch the reserved fields, and this leaves uninitialized values
there. Meanwhile the native ioctl does zero-clear the whole
structure, so we should follow the same rule in compat mode, too.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix duplicate XT-PIC seen in /proc/interrupts on x86 systems
that make use of 8259A Programmable Interrupt Controllers.
Specifically convert output like this:
CPU0
0: 76573 XT-PIC-XT-PIC timer
1: 11 XT-PIC-XT-PIC i8042
2: 0 XT-PIC-XT-PIC cascade
4: 8 XT-PIC-XT-PIC serial
6: 3 XT-PIC-XT-PIC floppy
7: 0 XT-PIC-XT-PIC parport0
8: 1 XT-PIC-XT-PIC rtc0
10: 448 XT-PIC-XT-PIC fddi0
12: 23 XT-PIC-XT-PIC eth0
14: 2464 XT-PIC-XT-PIC ide0
NMI: 0 Non-maskable interrupts
ERR: 0
to one like this:
CPU0
0: 122033 XT-PIC timer
1: 11 XT-PIC i8042
2: 0 XT-PIC cascade
4: 8 XT-PIC serial
6: 3 XT-PIC floppy
7: 0 XT-PIC parport0
8: 1 XT-PIC rtc0
10: 145 XT-PIC fddi0
12: 31 XT-PIC eth0
14: 2245 XT-PIC ide0
NMI: 0 Non-maskable interrupts
ERR: 0
that is one like we used to have from ~2.2 till it was changed
sometime.
The rationale is there is no value in this duplicate
information, it merely clutters output and looks ugly. We only
have one handler for 8259A interrupts so there is no need to
give it a name separate from the name already given to
irq_chip.
We could define meaningful names for handlers based on bits in
the ELCR register on systems that have it or the value of the
LTIM bit we use in ICW1 otherwise (hardcoded to 0 though with
MCA support gone), to tell edge-triggered and level-triggered
inputs apart. While that information does not affect 8259A
interrupt handlers it could help people determine which lines
are shareable and which are not. That is material for a
separate change though.
Any tools that parse /proc/interrupts are supposed not to be
affected since it was many years we used the format this change
converts back to.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.11.1410260147190.21390@eddie.linux-mips.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The convention for i2c_device_id name does not need to have company prefix.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1) switched_to_dl() check is wrong. We reschedule only
if rq->curr is deadline task, and we do not reschedule
if it's a lower priority task. But we must always
preempt a task of other classes.
2) dl_task_timer():
Policy does not change in case of priority inheritance.
rt_mutex_setprio() changes prio, while policy remains old.
So we lose some balancing logic in dl_task_timer() and
switched_to_dl() when we check policy instead of priority. Boosted
task may be rq->curr.
(I didn't change switched_from_dl() because no check is necessary
there at all).
I've looked at this place(switched_to_dl) several times and even fixed
this function, but found just now... I suppose some performance tests
may work better after this.
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1413909356.19914.128.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While offling node by hot removing memory, the following divide error
occurs:
divide error: 0000 [#1] SMP
[...]
Call Trace:
[...] handle_mm_fault
[...] ? try_to_wake_up
[...] ? wake_up_state
[...] __do_page_fault
[...] ? do_futex
[...] ? put_prev_entity
[...] ? __switch_to
[...] do_page_fault
[...] page_fault
[...]
RIP [<ffffffff810a7081>] task_numa_fault
RSP <ffff88084eb2bcb0>
The issue occurs as follows:
1. When page fault occurs and page is allocated from node 1,
task_struct->numa_faults_buffer_memory[] of node 1 is
incremented and p->numa_faults_locality[] is also incremented
as follows:
o numa_faults_buffer_memory[] o numa_faults_locality[]
NR_NUMA_HINT_FAULT_TYPES
| 0 | 1 |
---------------------------------- ----------------------
node 0 | 0 | 0 | remote | 0 |
node 1 | 0 | 1 | locale | 1 |
---------------------------------- ----------------------
2. node 1 is offlined by hot removing memory.
3. When page fault occurs, fault_types[] is calculated by using
p->numa_faults_buffer_memory[] of all online nodes in
task_numa_placement(). But node 1 was offline by step 2. So
the fault_types[] is calculated by using only
p->numa_faults_buffer_memory[] of node 0. So both of fault_types[]
are set to 0.
4. The values(0) of fault_types[] pass to update_task_scan_period().
5. numa_faults_locality[1] is set to 1. So the following division is
calculated.
static void update_task_scan_period(struct task_struct *p,
unsigned long shared, unsigned long private){
...
ratio = DIV_ROUND_UP(private * NUMA_PERIOD_SLOTS, (private + shared));
}
6. But both of private and shared are set to 0. So divide error
occurs here.
The divide error is rare case because the trigger is node offline.
This patch always increments denominator for avoiding divide error.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/54475703.8000505@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Unlocked access to dst_rq->curr in task_numa_compare() is racy.
If curr task is exiting this may be a reason of use-after-free:
task_numa_compare() do_exit()
... current->flags |= PF_EXITING;
... release_task()
... ~~delayed_put_task_struct()~~
... schedule()
rcu_read_lock() ...
cur = ACCESS_ONCE(dst_rq->curr) ...
... rq->curr = next;
... context_switch()
... finish_task_switch()
... put_task_struct()
... __put_task_struct()
... free_task_struct()
task_numa_assign() ...
get_task_struct() ...
As noted by Oleg:
<<The lockless get_task_struct(tsk) is only safe if tsk == current
and didn't pass exit_notify(), or if this tsk was found on a rcu
protected list (say, for_each_process() or find_task_by_vpid()).
IOW, it is only safe if release_task() was not called before we
take rcu_read_lock(), in this case we can rely on the fact that
delayed_put_pid() can not drop the (potentially) last reference
until rcu_read_unlock().
And as Kirill pointed out task_numa_compare()->task_numa_assign()
path does get_task_struct(dst_rq->curr) and this is not safe. The
task_struct itself can't go away, but rcu_read_lock() can't save
us from the final put_task_struct() in finish_task_switch(); this
reference goes away without rcu gp>>
The patch provides simple check of PF_EXITING flag. If it's not set,
this guarantees that call_rcu() of delayed_put_task_struct() callback
hasn't happened yet, so we can safely do get_task_struct() in
task_numa_assign().
Locked dst_rq->lock protects from concurrency with the last schedule().
Reusing or unmapping of cur's memory may happen without it.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1413962231.19914.130.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The race may happen when somebody is changing task_group of a forking task.
Child's cgroup is the same as parent's after dup_task_struct() (there just
memory copying). Also, cfs_rq and rt_rq are the same as parent's.
But if parent changes its task_group before it's called cgroup_post_fork(),
we do not reflect this situation on child. Child's cfs_rq and rt_rq remain
the same, while child's task_group changes in cgroup_post_fork().
To fix this we introduce fork() method, which calls sched_move_task() directly.
This function changes sched_task_group on appropriate (also its logic has
no problem with freshly created tasks, so we shouldn't introduce something
special; we are able just to use it).
Possibly, this decides the Burke Libbey's problem: https://lkml.org/lkml/2014/10/24/456
Signed-off-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414405105.19914.169.camel@tkhai
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Change ownership of the hpsa driver from Stephen M. Cameron
(Hewlett-Packard) to Don Brace (PMC-Sierra).
Change ownership of the cciss driver from Mike Miller (Hewlett-Packard)
to Don Brace (PMC-Sierra).
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
libcxgbi was always returning an ipv4 address for ISCSI_HOST_PARAM_IPADDRESS,
return appropriate address based on address family
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
Fixes: c53c6d6a68 ("scatterlist: allow chaining to preallocated chunks")
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In certain circumstances the PSL (Power Service Layer, which provides
translation services for CXL hardware) can send an interrupt for a
segment miss that the kernel has already handled. This can happen if
multiple translations for the same segment are queued in the PSL before
the kernel has restarted the first translation.
The CXL driver does not expect this situation and does not check if a
segment had already been handled. This could cause a duplicate segment
table entry which in turn caused a PSL error taking down the card.
This patch fixes the issue by checking for existing entries in the
segment table that match the segment we are trying to insert, so as to
avoid inserting duplicate entries.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch makes copro_calculate_slb() mask the ESID by the correct mask
for 1T vs 256M segments.
This has no effect by itself as the extra bits were ignored, but it
makes debugging the segment table entries easier and means that we can
directly compare the ESID values for duplicates without needing to worry
about masking in the comparison.
This will be used to simplify a comparison in the following patch.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the segment table hash calculation from cxl_load_segment()
into find_free_sste() since that is the only place it is actually used.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch simplifies the process of finding a free segment table entry
by disabling the secondary hash. This reduces the number of possible
entries in the segment table for a given address from 16 to 8.
Due to the large segment sizes we use it is extremely unlikely that the
secondary hash would ever have been used in practice, so this should not
have any negative impacts and may even improve performance due to the
reduced number of comparisons that software & hardware need to perform.
This patch clears the SC bit in the hardware's state register
(CXL_PSL_SR_An) to disable the secondary hash in the hardware since we
can no longer fill out entries using it.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add an ftrace_graph_is_dead() check to prepare_ftrace_return() in order to
detect an internal ftrace graph error. This allows to prevent further ftrace
graph handling and hopefully keeps the kernel alive.
This patch is the same like for all other architectures.
For unkown reasons s390 was left out.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fengguang Wu reported a boot crash on the x86 platform
via the 0-day Linux Kernel Performance Test:
cma: dma_contiguous_reserve: reserving 31 MiB for global area
BUG: Int 6: CR2 (null)
[<41850786>] dump_stack+0x16/0x18
[<41d2b1db>] early_idt_handler+0x6b/0x6b
[<41072227>] ? __phys_addr+0x2e/0xca
[<41d4ee4d>] cma_declare_contiguous+0x3c/0x2d7
[<41d6d359>] dma_contiguous_reserve_area+0x27/0x47
[<41d6d4d1>] dma_contiguous_reserve+0x158/0x163
[<41d33e0f>] setup_arch+0x79b/0xc68
[<41d2b7cf>] start_kernel+0x9c/0x456
[<41d2b2ca>] i386_start_kernel+0x79/0x7d
(See details at: https://lkml.org/lkml/2014/10/8/708)
It is because dma_contiguous_reserve() is called before
initmem_init() in x86, the variable high_memory is not
initialized but accessed by __pa(high_memory) in
dma_contiguous_reserve().
This patch moves dma_contiguous_reserve() after initmem_init()
so that high_memory is initialized before accessed.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: iamjoonsoo.kim@lge.com
Cc: 'Linux-MM' <linux-mm@kvack.org>
Cc: 'Weijie Yang' <weijie.yang.kh@gmail.com>
Link: http://lkml.kernel.org/r/000101cfef69%2431e528a0%2495af79e0%24%25yang@samsung.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Yoga 3 does not contain any physical rfkill switch. Therefore
disable the rfkill switch identically to the Yoga 2 approach.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The acpi-video backlight interface on the Acer KAV80 is broken, and worse
it causes the entire machine to slow down significantly after a suspend/resume.
Blacklist it, and use the acer-wmi backlight interface instead. Note that
the KAV80 is somewhat unique in that it is the only Acer model where we
fall back to acer-wmi after blacklisting, rather then using the native
(e.g. intel) backlight driver. This is done because there is no native
backlight interface on this model.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This reverts commit bf7588a085.
Ben says although the code is not correct "[this] fix was completely
wrong and does more damages than it fixes things."
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The charger manager obtained reference to fuel gauge power supply in probe
with power_supply_get_by_name() for later usage. However if fuel gauge
driver was removed and re-added then this reference would point to old
power supply (from driver which was removed).
This lead to accessing old (and probably invalid) memory which could be
observed with:
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/unbind
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/bind
$ cat /sys/devices/virtual/power_supply/battery/capacity
[ 240.480084] INFO: task cat:1393 blocked for more than 120 seconds.
[ 240.484799] Not tainted 3.17.0-next-20141007-00028-ge60b6dd79570 #203
[ 240.491782] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.499589] cat D c0469530 0 1393 1 0x00000000
[ 240.505947] [<c0469530>] (__schedule) from [<c0469d3c>] (schedule_preempt_disabled+0x14/0x20)
[ 240.514449] [<c0469d3c>] (schedule_preempt_disabled) from [<c046af08>] (mutex_lock_nested+0x1bc/0x458)
[ 240.523736] [<c046af08>] (mutex_lock_nested) from [<c0287a98>] (regmap_read+0x30/0x60)
[ 240.531647] [<c0287a98>] (regmap_read) from [<c032238c>] (max17042_get_property+0x2e8/0x350)
[ 240.540055] [<c032238c>] (max17042_get_property) from [<c03247d8>] (charger_get_property+0x264/0x348)
[ 240.549252] [<c03247d8>] (charger_get_property) from [<c0320764>] (power_supply_show_property+0x48/0x1e0)
[ 240.558808] [<c0320764>] (power_supply_show_property) from [<c027308c>] (dev_attr_show+0x1c/0x48)
[ 240.567664] [<c027308c>] (dev_attr_show) from [<c0141fb0>] (sysfs_kf_seq_show+0x84/0x104)
[ 240.575814] [<c0141fb0>] (sysfs_kf_seq_show) from [<c0140b18>] (kernfs_seq_show+0x24/0x28)
[ 240.584061] [<c0140b18>] (kernfs_seq_show) from [<c0104574>] (seq_read+0x1b0/0x484)
[ 240.591702] [<c0104574>] (seq_read) from [<c00e1e24>] (vfs_read+0x88/0x144)
[ 240.598640] [<c00e1e24>] (vfs_read) from [<c00e1f20>] (SyS_read+0x40/0x8c)
[ 240.605507] [<c00e1f20>] (SyS_read) from [<c000e760>] (ret_fast_syscall+0x0/0x48)
[ 240.612952] 4 locks held by cat/1393:
[ 240.616589] #0: (&p->lock){+.+.+.}, at: [<c01043f4>] seq_read+0x30/0x484
[ 240.623414] #1: (&of->mutex){+.+.+.}, at: [<c01417dc>] kernfs_seq_start+0x1c/0x8c
[ 240.631086] #2: (s_active#31){++++.+}, at: [<c01417e4>] kernfs_seq_start+0x24/0x8c
[ 240.638777] #3: (&map->mutex){+.+...}, at: [<c0287a98>] regmap_read+0x30/0x60
The charger-manager should get reference to fuel gauge power supply on
each use of get_property callback. The thermal zone 'tzd' field of
power supply should not be used because of the same reason.
Additionally this change solves also the issue with nested
thermal_zone_get_temp() calls and related false lockdep positive for
deadlock for thermal zone's mutex [1]. When fuel gauge is used as source of
temperature then the charger manager forwards its get_temp calls to fuel
gauge thermal zone. So actually different mutexes are used (one for
charger manager thermal zone and second for fuel gauge thermal zone) but
for lockdep this is one class of mutex.
The recursion is removed by retrieving temperature through power
supply's get_property().
In case external thermal zone is used ('cm-thermal-zone' property is
present in DTS) the recursion does not exist. Charger manager simply
exports POWER_SUPPLY_PROP_TEMP_AMBIENT property (instead of
POWER_SUPPLY_PROP_TEMP) thus no thermal zone is created for this power
supply.
[1] https://lkml.org/lkml/2014/10/6/309
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 3bb3dbbd56 ("power_supply: Add initial Charger-Manager driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The charger manager supports POWER_SUPPLY_PROP_TEMP property and acts
as a thermal zone if any of these conditions match:
1. Fuel gauge used by charger manager supports POWER_SUPPLY_PROP_TEMP.
2. 'cm-thermal-zone' property is present in DTS (then it will supersede
the fuel gauge temperature property).
However in case 1 (fuel gauge reports temperature and 'cm-thermal-zone'
is not set) the charger manager forwards its get_temp calls to fuel
gauge thermal zone.
This leads to reporting by lockdep a false positive deadlock for thermal
zone's mutex because of nested calls to thermal_zone_get_temp(). This is
false positive because these are different mutexes: one for charger
manager thermal zone and second for fuel gauge thermal zone.
Get rid of false lockdep alert and recursive call by setting
'no_thermal' property for this power supply class. The thermal zone for
charger manager won't be created (user space does not use it anyway).
The lockdep report:
[ 2.540339] charger-manager charger-manager@0: Ignoring full-battery voltage threshold as it is not supplied
[ 2.540351] charger-manager charger-manager@0: Ignoring full-battery full capacity threshold as it is not supplied
[ 2.546296]
[ 2.546302] =============================================
[ 2.546305] [ INFO: possible recursive locking detected ]
[ 2.546312] 3.17.0-rc6-next-20140926-00012-gbb13895e46af-dirty #39 Not tainted
[ 2.546316] ---------------------------------------------
[ 2.546321] swapper/0/1 is trying to acquire lock:
[ 2.546348] (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546352]
[ 2.546352] but task is already holding lock:
[ 2.546369] (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546373]
[ 2.546373] other info that might help us debug this:
[ 2.546376] Possible unsafe locking scenario:
[ 2.546376]
[ 2.546378] CPU0
[ 2.546380] ----
[ 2.546386] lock(&tz->lock);
[ 2.546392] lock(&tz->lock);
[ 2.546394]
[ 2.546394] *** DEADLOCK ***
[ 2.546394]
[ 2.546397] May be due to missing lock nesting notation
[ 2.546397]
[ 2.546401] 2 locks held by swapper/0/1:
[ 2.546430] #0: (&dev->mutex){......}, at: [<c02720c4>] __driver_attach+0x58/0x98
[ 2.546448] #1: (&tz->lock){+.+...}, at: [<c0321d24>] thermal_zone_get_temp+0x38/0x68
[ 2.546451]
[ 2.546451] stack backtrace:
[ 2.546460] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc6-next-20140926-00012-gbb13895e46af-dirty #39
[ 2.546497] [<c00140f0>] (unwind_backtrace) from [<c0011228>] (show_stack+0x10/0x14)
[ 2.546526] [<c0011228>] (show_stack) from [<c046158c>] (dump_stack+0x70/0xbc)
[ 2.546554] [<c046158c>] (dump_stack) from [<c005e32c>] (validate_chain.isra.24+0x718/0x890)
[ 2.546569] [<c005e32c>] (validate_chain.isra.24) from [<c005f0a0>] (__lock_acquire+0x498/0xa78)
[ 2.546581] [<c005f0a0>] (__lock_acquire) from [<c005fb50>] (lock_acquire+0x78/0xb8)
[ 2.546594] [<c005fb50>] (lock_acquire) from [<c0464260>] (mutex_lock_nested+0x64/0x458)
[ 2.546605] [<c0464260>] (mutex_lock_nested) from [<c0321d24>] (thermal_zone_get_temp+0x38/0x68)
[ 2.546634] [<c0321d24>] (thermal_zone_get_temp) from [<c031f1e0>] (charger_get_property+0x10c/0x348)
[ 2.546649] [<c031f1e0>] (charger_get_property) from [<c031af18>] (power_supply_read_temp+0x28/0x58)
[ 2.546662] [<c031af18>] (power_supply_read_temp) from [<c0321d38>] (thermal_zone_get_temp+0x4c/0x68)
[ 2.546676] [<c0321d38>] (thermal_zone_get_temp) from [<c03233d8>] (thermal_zone_device_update+0x24/0x9c)
[ 2.546687] [<c03233d8>] (thermal_zone_device_update) from [<c0323874>] (thermal_zone_device_register+0x424/0x550)
[ 2.546701] [<c0323874>] (thermal_zone_device_register) from [<c031b3c0>] (__power_supply_register+0x2a4/0x348)
[ 2.546714] [<c031b3c0>] (__power_supply_register) from [<c031ff64>] (charger_manager_probe+0x600/0xe5c)
[ 2.546727] [<c031ff64>] (charger_manager_probe) from [<c0273384>] (platform_drv_probe+0x48/0xa4)
[ 2.546746] [<c0273384>] (platform_drv_probe) from [<c0271f54>] (driver_probe_device+0x10c/0x224)
[ 2.546760] [<c0271f54>] (driver_probe_device) from [<c0272100>] (__driver_attach+0x94/0x98)
[ 2.546772] [<c0272100>] (__driver_attach) from [<c0270780>] (bus_for_each_dev+0x54/0x88)
[ 2.546784] [<c0270780>] (bus_for_each_dev) from [<c027173c>] (bus_add_driver+0xd4/0x1d0)
[ 2.546797] [<c027173c>] (bus_add_driver) from [<c027271c>] (driver_register+0x78/0xf4)
[ 2.546809] [<c027271c>] (driver_register) from [<c0008984>] (do_one_initcall+0x80/0x1d4)
[ 2.546829] [<c0008984>] (do_one_initcall) from [<c0612d60>] (kernel_init_freeable+0x10c/0x1d8)
[ 2.546847] [<c0612d60>] (kernel_init_freeable) from [<c045c238>] (kernel_init+0x8/0xec)
[ 2.546863] [<c045c238>] (kernel_init) from [<c000e828>] (ret_from_fork+0x14/0x2c)
[ 2.551396] charger-manager charger-manager@0: 'chg-reg' regulator's externally_control is 0
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'no_thermal' property to the power supply class. If true then
thermal zone won't be created for this power supply in
power_supply_register().
Power supply drivers may want to set it if they support
POWER_SUPPLY_PROP_TEMP and they are forwarding this get property call to
other thermal zone.
If they won't set it lockdep may report false positive deadlock for
thermal zone's mutex because of nested calls to thermal_zone_get_temp().
First is the call to thermal_zone_get_temp() of the driver's thermal
zone. Thermal core gets POWER_SUPPLY_PROP_TEMP property from this
driver. The driver then calls other thermal zone thermal_zone_get_temp()
and returns result.
Example of such driver is charger manager.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Memory allocated for 'name' was leaking if required binding properties
were not present.
The memory for 'name' was allocated early at probe with kasprintf(). It
was freed in error paths executed before and after parsing DTS but not
in that error path.
Fix the error path for parsing device tree properties.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: faffd234cf ("bq2415x_charger: Add DT support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power_supply_get_by_phandle() on error returns ENODEV or NULL.
The driver later expects obtained pointer to power supply to be
valid or NULL. If it is not NULL then it dereferences it in
bq2415x_notifier_call() which would lead to dereferencing ENODEV-value
pointer.
Properly handle the power_supply_get_by_phandle() error case by
replacing error value with NULL. This indicates that usb charger
detection won't be used.
Fix also memory leak of 'name' if power_supply_get_by_phandle() fails
with NULL and probe should defer.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: faffd234cf ("bq2415x_charger: Add DT support")
Cc: <stable@vger.kernel.org>
[small fix regarding the missing ti,usb-charger-detection info message]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Kernel dump (WARN_ON) ocurred during system boot-up inside regmap_write():
------------[ cut here ]------------
WARNING: CPU: 0 PID: 47 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xe8/0x108()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 47 Comm: kworker/u2:2 Not tainted 3.18.0-rc1-10245-gb75d289-dirty #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<80012294>] (dump_backtrace) from [<80012578>] (show_stack+0x18/0x1c)
r6:8097c73c r5:8097c73c r4:00000000 r3:be33ba80
[<80012560>] (show_stack) from [<806aac48>] (dump_stack+0x8c/0xa4)
[<806aabbc>] (dump_stack) from [<8002a694>] (warn_slowpath_common+0x70/0x94)
r6:80062838 r5:00000009 r4:bd827b30 r3:be33ba80
[<8002a624>] (warn_slowpath_common) from [<8002a6f0>] (warn_slowpath_fmt+0x38/0x40)
r8:00000004 r7:00000001 r6:000080d0 r5:60000193 r4:bd826010
[<8002a6bc>] (warn_slowpath_fmt) from [<80062838>] (lockdep_trace_alloc+0xe8/0x108)
r3:80831590 r2:8082e160
[<80062750>] (lockdep_trace_alloc) from [<800ea5dc>] (kmem_cache_alloc+0x28/0x134)
r5:000080d0 r4:be001f00
[<800ea5b4>] (kmem_cache_alloc) from [<8038d72c>] (regcache_rbtree_write+0x15c/0x648)
r10:00000000 r9:0000001c r8:00000004 r7:00000001 r6:00000000 r5:bd819a00
r4:00000000 r3:811aea88
[<8038d5d0>] (regcache_rbtree_write) from [<8038c4d8>] (regcache_write+0x5c/0x64)
r10:be3f9f88 r9:00000000 r8:00000004 r7:00000001 r6:00000000 r5:00000001
r4:bd819a00
[<8038c47c>] (regcache_write) from [<8038b0dc>] (_regmap_raw_write+0x134/0x5f4)
r6:be3f9f84 r5:00000001 r4:bd819a00 r3:00000001
[<8038afa8>] (_regmap_raw_write) from [<8038b610>] (_regmap_bus_raw_write+0x74/0x94)
r10:00000000 r9:00000001 r8:be3fb080 r7:bd819a00 r6:00000001 r5:00000000
r4:bd819a00
[<8038b59c>] (_regmap_bus_raw_write) from [<8038a8b4>] (_regmap_write+0x60/0x9c)
r6:00000001 r5:00000000 r4:bd819a00 r3:8038b59c
[<8038a854>] (_regmap_write) from [<8038ba24>] (regmap_write+0x48/0x68)
r7:bd81ad80 r6:00000001 r5:00000000 r4:bd819a00
[<8038b9dc>] (regmap_write) from [<80528f30>] (fsl_asrc_dai_probe+0x34/0x104)
r6:bd888628 r5:be3fb080 r4:be3b4410 r3:be3b442c
------------[ dump end ]------------
=============================================================================
2741 /*
2742 * Oi! Can't be having __GFP_FS allocations with IRQs disabled.
2743 */
2744 if (DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags)))
2745 return;
=============================================================================
By looking at 2744 line, we can get that it's because regcache_rbtree_write()
would call kmalloc() with GFP flag if it couldn't find an existing block to
insert nodes while this kmalloc() call is inside a spin_lock_irq_save pair,
i.e. IRQs disabled.
Even though this may be a bug that should be fixed, I still try to send this
patch as a quick fix (work around) since it does no harm to assign default
values of every registers when using regcache.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Three changes for the Armada DRM driver:
1. Add back the flags which tell the DRM core that we can do vblank. This
was removed in error during the recent restructuring, and came to light
while trying textured Xv rendering.
2. Fixing a refcount leak with Xv overlay.
3. As per recent discussion, the drm_vblank_pre_modeset() calls can cause
deadlock with other changes to generic code. This change prevents those
deadlocks by switching to the drm_crtc_vblank_*() calls instead.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/armada: convert to use vblank_on/off calls
drm/armada: fix page_flip refcounting leak
drm/armada: add IRQ support back
introduce two configs:
- hidden CONFIG_BPF to select eBPF interpreter that classic socket filters
depend on
- visible CONFIG_BPF_SYSCALL (default off) that tracing and sockets can use
that solves several problems:
- tracing and others that wish to use eBPF don't need to depend on NET.
They can use BPF_SYSCALL to allow loading from userspace or select BPF
to use it directly from kernel in NET-less configs.
- in 3.18 programs cannot be attached to events yet, so don't force it on
- when the rest of eBPF infra is there in 3.19+, it's still useful to
switch it off to minimize kernel size
bloat-o-meter on x64 shows:
add/remove: 0/60 grow/shrink: 0/2 up/down: 0/-15601 (-15601)
tested with many different config combinations. Hopefully didn't miss anything.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anish Bhatt says:
====================
cxgb4 : DCBx fixes for apps/host lldp agents
This patchset contains some minor fixes for cxgb4 DCBx code. Chiefly, cxgb4
was not cleaning up any apps added to kernel app table when link was lost.
Disabling DCBx in firmware would automatically set DCBx state to host-managed
and enabled, we now wait for an explicit enable call from an lldp agent instead
First patch was originally sent to net-next, but considering it applies to
correcting behaviour of code already in net, I think it qualifies as a bug fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling DCBx in firmware automatically enables DCBx for control via host
lldp agents. Wait for an explicit setstate call from an lldp agents to enable
DCBx instead.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out any DCB apps we might have added to kernel table when we lose DCB
sync (or IEEE equivalent event). These were previously left behind and not
cleaned up correctly. IEEE allows individual components to work independently,
so improve check for IEEE completion by specifying individual components.
Fixes: 10b0046685 ("cxgb4: IEEE fixes for DCBx state machine")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Allow to recycle a TCP port in conntrack when the change role from
server to client, from Marcelo Leitner.
2) Fix possible off by one access in ip_set_nfnl_get_byindex(), patch
from Dan Carpenter.
3) alloc_percpu returns NULL on error, no need for IS_ERR() in nf_tables
chain statistic updates. From Sabrina Dubroca.
4) Don't compile ip options in bridge netfilter, this mangles the packet
and bridge should not alter layer >= 3 headers when forwarding packets.
Patch from Herbert Xu and tested by Florian Westphal.
5) Account the final NLMSG_DONE message when calculating the size of the
nflog netlink batches. Patch from Florian Westphal.
6) Fix a possible netlink attribute length overflow with large packets.
Again from Florian Westphal.
7) Release the skbuff if nfnetlink_log fails to put the final
NLMSG_DONE message. This fixes a leak on error. This shouldn't ever
happen though, otherwise this means we miscalculate the netlink batch
size, so spot a warning if this ever happens so we can track down the
problem. This patch from Houcheng Lin.
8) Look at the right list when recycling targets in the nft_compat,
patch from Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34e5a5273d ("cpufreq: cpufreq-dt: extend with
platform_data") changed cpufreq_init() to only call
cpumask_setall(policy->cpus) if the platform data indicates that all
CPUs share the same clock. Before, cpufreq_generic_init() did this
unconditionally.
This causes a crash on r8a7791/koelsch when resuming from s2ram:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee71f980
[0000003c] *pgd=6eeb6003, *pmd=6e0e9003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1397 Comm: s2ram Tainted: G W 3.18.0-rc2-koelsch-00762-g7eed2a4e61d2d978 #581
task: ee6b76c0 ti: ee7f0000 task.ti: ee7f0000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c029e084>] lr : [<c029e07c>] psr: 60000153
sp : ee7f1d48 ip : ee7f1d48 fp : ee7f1d84
r10: c04e8448 r9 : 00000000 r8 : 00000001
r7 : c054a8c4 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c054a950
Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment user
Control: 30c5307d Table: 6e71f980 DAC: fffffffd
Process s2ram (pid: 1397, stack limit = 0xee7f0240)
...
Backtrace:
[<c029de38>] (__cpufreq_add_dev.isra.24) from [<c029e620>] (cpufreq_cpu_callback+0x6c/0x74)
r10:eec75240 r9:c04e8448 r8:c04ef3a0 r7:00000001 r6:00000012 r5:00000000
r4:00000012
[<c029e5b4>] (cpufreq_cpu_callback) from [<c003f20c>] (notifier_call_chain+0x48/0x70)
r4:ffffffdd r3:c029e5b4
[<c003f1c4>] (notifier_call_chain) from [<c003f2cc>] (__raw_notifier_call_chain+0x1c/0x24)
r8:00000001 r7:00000010 r6:00000000 r5:00000000 r4:00000012 r3:ffffffff
[<c003f2b0>] (__raw_notifier_call_chain) from [<c0026a00>] (__cpu_notify+0x34/0x50)
[<c00269cc>] (__cpu_notify) from [<c0026a34>] (cpu_notify+0x18/0x1c)
r4:00000001
[<c0026a1c>] (cpu_notify) from [<c0026c44>] (_cpu_up+0x108/0x144)
[<c0026b3c>] (_cpu_up) from [<c0381c68>] (enable_nonboot_cpus+0x68/0xb8)
r10:00000000 r9:c04e8ee6 r8:00000000 r7:00000003 r6:c04e8528 r5:c0506248
r4:00000001
[<c0381c00>] (enable_nonboot_cpus) from [<c0059038>] (suspend_devices_and_enter+0x29c/0x3e8)
r6:c0506e70 r5:00000000 r4:00000000 r3:60000153
Restore the old default of calling cpumask_setall(policy->cpus) if no
platform data is available to fix this.
Fixes: 34e5a5273d (cpufreq: cpufreq-dt: extend with platform_data)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull media fixes from Mauro Carvalho Chehab:
"A series of driver fixes:
- a few compilation fixes with randconfigs
- one potential compilation breakage on userspace due to the usage of
a gcc extension
- several warnings fixed
- some other random driver fixes"
* tag 'media/v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (22 commits)
[media] s5p-jpeg: Avoid -Wuninitialized warning in s5p_jpeg_parse_hdr
[media] s5p-fimc: Only build suspend/resume for PM
[media] s5p-jpeg: Only build suspend/resume for PM
[media] Remove references to non-existent PLAT_S5P symbol
[media] videobuf-dma-contig: set vm_pgoff to be zero to pass the sanity check in vm_iomap_memory()
[media] tw68: remove bogus I2C_ALGOBIT dependency
[media] usbvision-video: two use after frees
[media] tw68: remove deprecated IRQF_DISABLED
[media] xc5000: use after free in release()
[media] em28xx-input: NULL dereference on error
[media] wl128x: fix fmdbg compiler warning
Revert "[media] v4l2-dv-timings: fix a sparse warning"
[media] hackrf: harmless off by one in debug code
[media] cx23885: initialize config structs for T9580
[media] v4l: uvcvideo: Fix buffer completion size check
[media] vivid: fix buffer overrun
[media] saa7146: Create a device name before it's used
[media] em28xx: fix uninitialized variable warning
[media] vivid: fix Kconfig FB dependency
[media] anysee: make sure loading modules is const
...
Pull EDAC fixes from Borislav Petkov:
"Correct severity of reported errors in several EDAC drivers. From
Jason Baron"
* tag 'edac_fixes_for_3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
e7xxx_edac: Report CE events properly
cpc925_edac: Report UE events properly
i82860_edac: Report CE events properly
i3200_edac: Report CE events properly
Pull spi fixes from Mark Brown:
"Quite a few driver fixes in here, including some fairly substantial
ones for the recently added Rockchip driver, plus a fix for spidev to
more reliably support bidirectional transfers which is fairly large
but basically mechanical.
It's a bit more code than I'd like but all fixes"
* tag 'spi-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: orion: fix potential NULL pointer de-reference
spi/rockchip: spi controller must be disabled in tx callback too
spi/rockchip: fix bug that cause spi transfer timed out in DMA duplex mode
spi/rockchip: fix bug that case spi can't go as fast as slave request
spi: pl022: Fix incorrect dma_unmap_sg
spi: spidev: Use separate TX and RX bounce buffers
spi: dw: Initialize of_node to discover DT node children
Pull regulator fixes from Mark Brown:
"A couple of fixes for v3.18, one fix for an incorrect voltage to
register mapping in the rk808 driver and a fix for a build failure in
some SH defconfigs"
* tag 'regulator-v3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Include err.h from consumer.h to fix build failure
regulator: rk808: Fix min_uV for DCDC1 & DCDC2
The code looks for an already loaded target, and the correct list to search
is nft_target_list, not nft_match_list.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In one of Dave's cleanup commits he forgot to call btrfs_end_io_wq_exit on
unload, which makes us unable to unload and then re-load the btrfs module. This
fixes the problem. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
If we couldn't find our extent item, we accessed the current slot
(path->slots[0]) to check if it corresponds to an equivalent skinny
metadata item. However this slot could be beyond our last item in the
leaf (i.e. path->slots[0] >= btrfs_header_nritems(leaf)), in which case
we shouldn't process it.
Since btrfs_lookup_extent() is only used to find extent items for data
extents, fix this by removing completely the logic that looks up for an
equivalent skinny metadata item, since it can not exist.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
The initial patch c926093ec5 (btrfs: add more superblock checks)
did not properly use the macro accessors that wrap endianness and the
code would not work correctly on big endian machines.
Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Commit 673ce00c5d (ARM: omap2plus_defconfig: Add support for
distros with systemd) caused considerable bloat as noted by
Paul Walmsley <paul@pwsan.com>.
Let's fix this issue by making what we can into loadable modules
for the systemd options. That's only IPV6 and AUTOFS4_FS it
seems, and IPv6 defaults to a loadable module.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "SOCFPGA defconfig update" from Dinh Nguyen:
Remove extra un-used options in the socfpga_defconfig by doing
"make savedefconfig". Along with this commit, add the configs to enable
support for most filesystems, add regulator and SRAM support, and time
stamps on printk().
* tag 'socfpga_defconfig_for_v3.19' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "arm: pxa: fixes for v3.18-rc2" from Robert Jarzmik:
One small fix for a bug triggered by the activation of low level debug
code in all pxa variants in v3.17. The fix is a trivial Kconfig value
fix for an addressing conflict.
This reverts bceee4a97e ("PCI: pciehp: Prevent NULL dereference during
probe") because it was accidentally applied twice:
62e4492c30 ("PCI: Prevent NULL dereference during pciehp probe")
bceee4a97e ("PCI: pciehp: Prevent NULL dereference during probe")
Revert the latter to dispose of the duplicated code block.
[bhelgaas: tidy changelog, drop stable tag]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andreas Noever <andreas.noever@gmail.com>
If a device's dev_pm_ops::freeze callback fails during the QUIESCE
phase, we don't rollback things correctly calling the thaw and complete
callbacks. This could leave some devices in a suspended state in case of
an error during resuming from hibernation.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If an asynchronous suspend_late or freeze_late callback fails
during the SUSPEND, FREEZE or QUIESCE phases, we don't propagate the
corresponding error correctly, in effect ignoring the error and
continuing the suspend-to-ram/hibernation. During suspend-to-ram this
could leave some devices without a valid saved context, leading to a
failure to reinitialize them during resume. During hibernation this
could leave some devices active interfeering with the creation /
restoration of the hibernation image. Also this could leave the
corresponding devices without a valid saved context and failure to
reinitialize them during resume.
Fixes: de377b3972 (PM / sleep: Asynchronous threads for suspend_late)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 6ab3430129 ("mfd: Add ACPI support") made the MFD subdevices
share the parent MFD ACPI companion if no _HID/_CID is specified for
the subdevice in mfd_cell description. However, since all the subdevices
share the ACPI companion, the match and modalias generation logic started
to use the ACPI companion as well resulting this:
# cat /sys/bus/platform/devices/HID-SENSOR-200041.6.auto/modalias
acpi:INT33D1:PNP0C50:
instead of the expected one
# cat /sys/bus/platform/devices/HID-SENSOR-200041.6.auto/modalias
platform:HID-SENSOR-200041
In other words the subdevice modalias is overwritten by the one taken from
ACPI companion. This causes udev not to load the driver anymore.
It is useful to be able to share the ACPI companion so that MFD subdevices
(and possibly other devices as well) can access the ACPI resources even if
they do not have ACPI representation in the namespace themselves.
An example where this is used is Minnowboard LPC driver that creates GPIO
as a subdevice among other things. Without the ACPI companion gpiolib is
not able to lookup the corresponding GPIO controller from ACPI GpioIo
resource.
To fix this, restrict the match and modalias logic to be limited to the
first (primary) physical device associated with the given ACPI comapnion.
The secondary devices will still be able to access the ACPI companion,
but they will be matched in a different way.
Fixes: 6ab3430129 (mfd: Add ACPI support)
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the regulator connected to the CPU voltage plane doesn't
support an OPP specified voltage with the acceptable tolerance
it's better to just disable the OPP instead of constantly
failing the voltage scaling later on.
Includes a fix to move initialization of opp_freq outside
the loop to avoid an endless loop from Geert Uytterhoeven.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 33fb0d01ce.
18dcf433f3 ("AHCI: Optimize single IRQ interrupt processing") is
scheduled to be reverted. This is an optimization dependent on the
mentioned commit. Revert it first.
Signed-off-by: Tejun Heo <tj@kernel.org>
snd_bebob_stream_check_internal_clock() may get an id from
saffirepro_both_clk_src_get (via clk_src->get()) that was uninitialized.
a) make logic in saffirepro_both_clk_src_get explicit
b) test if id used in snd_bebob_stream_check_internal_clock matches array size
[fixed missing signed prefix to *_maps[] by tiwai]
Signed-off-by: Christian Vogel <vogelchr@vogel.cx>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel provided vdso functions do not get a stack frame from the
calling function and therefore may not change the stack contents, unless
they allocate space on their own.
This problem was exposed with 070b7be633 "s390/vdso: replace stck with
stcke" which writes 16 bytes instead of 8 bytes into the stack frame. These
additional 8 bytes however were indeed used by the caller (glibc) to save
data and therefore this data was corrupted by the vdso code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The last high frequency call site of the STCK instruction is
do_account_vtime. Replace it with the faster STCKF instruction.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the current code, the base and size parameters order is not consistent
in functions declaration and definition. If someone calls these functions
according to the declaration parameters order in cma.h, he will run into
some bug and it's hard to find the reason.
This patch makes the parameters order consistent in functions declaration
and definition.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Commit 95b0e655f9 ("ARM: mm: don't limit default CMA region only to
low memory") extended CMA memory reservation to allow usage of high
memory. It relied on commit f7426b983a ("mm: cma: adjust address limit
to avoid hitting low/high memory boundary") to ensure that the reserved
block never crossed the low/high memory boundary. While the
implementation correctly lowered the limit, it failed to consider the
case where the base..limit range crossed the low/high memory boundary
with enough space on each side to reserve the requested size on either
low or high memory.
Rework the base and limit adjustment to fix the problem. The function
now starts by rejecting the reservation altogether for fixed
reservations that cross the boundary, tries to reserve from high memory
first and then falls back to low memory.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The fixed parameter to cma_declare_contiguous() tells the function
whether the given base address must be honoured or should be considered
as a hint only. The API considers a zero base address as meaning any
base address, which must never be considered as a fixed value.
Part of the implementation correctly checks both fixed and base != 0,
but two locations check the fixed value only. Set fixed to false when
base is 0 to fix that and simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
If activation of the CMA area fails its mutex won't be initialized,
leading to an oops at allocation time when trying to lock the mutex. Fix
this by setting the cma area count field to 0 when activation fails,
leading to allocation returning NULL immediately.
Cc: <stable@vger.kernel.org> # v3.17
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
ASoC: Fixes for v3.18
A few small driver fixes for v3.18 plus the removal of the s6000 support
since the relevant chip is no longer supported in mainline.
Turning vdd on/off can generate a long hpd pulse on eDP ports. In order
to handle hpd we would need to turn on vdd to perform aux transfers.
This would lead to an endless cycle of
"vdd off -> long hpd -> vdd on -> detect -> vdd off -> ..."
So ignore long hpd pulses on eDP ports. eDP panels should be physically
tied to the machine anyway so they should not actually disappear and
thus don't need long hpd handling. Short hpds are still needed for link
re-train and whatnot so we can't just turn off the hpd interrupt
entirely for eDP ports. Perhaps we could turn it off whenever the panel
is disabled, but just ignoring the long hpd seems sufficient.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Sometimes we seem to get utter garbage from DPCD reads. The resulting
buffer is filled with the same byte, and the operation completed without
errors. My HP ZR24w monitor seems particularly susceptible to this
problem once it's gone into a sleep mode.
The issue seems to happen only for the first AUX message that wakes the
sink up. But as the first AUX read we often do is the DPCD receiver
cap it does wreak a bit of havoc with subsequent link training etc. when
the receiver cap bw/lane/etc. information is garbage.
A sufficient workaround seems to be to perform a single byte dummy read
before reading the actual data. I suppose that just wakes up the sink
sufficiently and we can just throw away the returned data in case it's
crap. DP_DPCD_REV seems like a sufficiently safe location to read here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It is lite version of AIO machine(0x0626).
The audio layout of this machine was similar with SSID 0x0626.
The audio was same as commit ad8ff99e6b.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Terratec PHASE 88 rack fw has two registers for source of clock, one is
for internal/external, and another is for wordclock/spdif for external.
When clock source is internal, information in another register has no meaning.
Thus it must be ignored, but current implementation decodes it. This causes
over-indexing reference to labels.
Reported-by: András Murányi <muranyia@gmail.com>
Tested-by: András Murányi <muranyia@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0b0b0893d4 "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().
The issue is described here:
"powerpc/pci: Fix IO space breakage after of_pci_range_to_resource()
change"
(sha1: aeba3731b1)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The time Kconfig expects that NR_CPUS is defined.
This patch remove this config warning:
"kernel/time/Kconfig:163:warning: range is invalid"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not reuse skb if it was pfmemalloc tainted, otherwise
future frame might be dropped anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen says:
====================
irq sync fixes
This two patch series fixes a race where an interrupt handler could access a
freed memory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After moving the EQ ownership to software effectively destroying it, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying the EQ, the object responsible for generating interrupts, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer. This patch solves a very
rare case when we get panic on driver unload.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call of 'kfree(ci->hw_bank.regmap)' in ci_hdrc_remove() sometimes causes
a kernel oops when removing the ci_hdrc module.
Since there is no separate memory allocated for the ci->hw_bank.regmap array,
there is no need to free it.
Cc: v3.14+ <stable@@vger.kernel.org>
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make Octeon GPIO IRQ chip CPU hotplug-aware
Seems that irq_cpu_offline callbacks were forgotten in v1 and v2 CIU
GPIO chips. There is such a callback for octeon_irq_chip_ciu2_gpio,
covering CIU2 chips. Without this callback GPIO IRQs are not being migrated
during core offlining. Patch is tested on Octeon II.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c387f07e62 (clocksource: arm_arch_timer: Discard unavailable
timers correctly) changed the way the driver makes sure both the memory
and system-register timers have been probed before finalizing the probing.
There is a interesting flaw in this logic that leads to this final step
never to be executed. Things seems to work pretty well until something
actually needs the data that is produced during this final stage.
For example, KVM explodes on the first run of a guest when executed on
a platform that has both memory and sysreg nodes (Juno, for example).
Just fix the damned logic, and enjoy booting VMs again.
Tested on a Juno system.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
free_pi_state and exit_pi_state_list both clean up futex_pi_state's.
exit_pi_state_list takes the hb lock first, and most callers of
free_pi_state do too. requeue_pi doesn't, which means free_pi_state
can free the pi_state out from under exit_pi_state_list. For example:
task A | task B
exit_pi_state_list |
pi_state = |
curr->pi_state_list->next |
| futex_requeue(requeue_pi=1)
| // pi_state is the same as
| // the one in task A
| free_pi_state(pi_state)
| list_del_init(&pi_state->list)
| kfree(pi_state)
list_del_init(&pi_state->list) |
Move the free_pi_state calls in requeue_pi to before it drops the hb
locks which it's already holding.
[ tglx: Removed a pointless free_pi_state() call and the hb->lock held
debugging. The latter comes via a seperate patch ]
Signed-off-by: Brian Silverman <bsilver16384@gmail.com>
Cc: austin.linux@gmail.com
Cc: darren@dvhart.com
Cc: peterz@infradead.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1414282837-23092-1-git-send-email-bsilver16384@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c: In function ‘xgene_enet_ecc_init’:
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:126: warning: ‘data’ may be used uninitialized in this function
Depending on the arbitrary value on the stack, the loop may terminate
too early, and cause a bogus -ENODEV failure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to cancel the work queue after rcu grace period,
otherwise it can be rescheduled by incoming packets.
We need to purge queue if some skbs are still in it.
We can use __skb_queue_head_init() variant in
macvlan_process_broadcast()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 412ca1550c ("macvlan: Move broadcasts into a work queue")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu tcp_md5sig_pool contains memory blobs that ultimately
go through sg_set_buf().
-> sg_set_page(sg, virt_to_page(buf), buflen, offset_in_page(buf));
This requires that whole area is in a physically contiguous portion
of memory. And that @buf is not backed by vmalloc().
Given that alloc_percpu() can use vmalloc() areas, this does not
fit the requirements.
Replace alloc_percpu() by a static DEFINE_PER_CPU() as tcp_md5sig_pool
is small anyway, there is no gain to dynamically allocate it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 765cf9976e ("tcp: md5: remove one indirection level in tcp_md5sig_pool")
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Vrabel says:
====================
xen-netback: guest Rx queue drain and stall fixes
This series fixes two critical xen-netback bugs.
1. Netback may consume all of host memory by queuing an unlimited
number of skb on the internal guest Rx queue. This behaviour is
guest triggerable.
2. Carrier flapping under high traffic rates which reduces
performance.
The first patch is a prerequite. Removing support for frontends with
feature-rx-notify makes it easier to reason about the correctness of
netback since it no longer has to support this outdated and broken
mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a frontend not receiving packets it is useful to detect this and
turn off the carrier so packets are dropped early instead of being
queued and drained when they expire.
A to-guest queue is stalled if it doesn't have enough free slots for a
an extended period of time (default 60 s).
If at least one queue is stalled, the carrier is turned off (in the
expectation that the other queues will soon stall as well). The
carrier is only turned on once all queues are ready.
When the frontend connects, all the queues start in the stalled state
and only become ready once the frontend queues enough Rx requests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netback needs to discard old to-guest skb's (guest Rx queue drain) and
it needs detect guest Rx stalls (to disable the carrier so packets are
discarded earlier), but the current implementation is very broken.
1. The check in hard_start_xmit of the slot availability did not
consider the number of packets that were already in the guest Rx
queue. This could allow the queue to grow without bound.
The guest stops consuming packets and the ring was allowed to fill
leaving S slot free. Netback queues a packet requiring more than S
slots (ensuring that the ring stays with S slots free). Netback
queue indefinately packets provided that then require S or fewer
slots.
2. The Rx stall detection is not triggered in this case since the
(host) Tx queue is not stopped.
3. If the Tx queue is stopped and a guest Rx interrupt occurs, netback
will consider this an Rx purge event which may result in it taking
the carrier down unnecessarily. It also considers a queue with
only 1 slot free as unstalled (even though the next packet might
not fit in this).
The internal guest Rx queue is limited by a byte length (to 512 Kib,
enough for half the ring). The (host) Tx queue is stopped and started
based on this limit. This sets an upper bound on the amount of memory
used by packets on the internal queue.
This allows the estimatation of the number of slots for an skb to be
removed (it wasn't a very good estimate anyway). Instead, the guest
Rx thread just waits for enough free slots for a maximum sized packet.
skbs queued on the internal queue have an 'expires' time (set to the
current time plus the drain timeout). The guest Rx thread will detect
when the skb at the head of the queue has expired and discard expired
skbs. This sets a clear upper bound on the length of time an skb can
be queued for. For a guest being destroyed the maximum time needed to
wait for all the packets it sent to be dropped is still the drain
timeout (10 s) since it will not be sending new packets.
Rx stall detection is reintroduced in a later commit.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frontends that do not provide feature-rx-notify may stall because
netback depends on the notification from frontend to wake the guest Rx
thread (even if can_queue is false).
This could be fixed but feature-rx-notify was introduced in 2006 and I
am not aware of any frontends that do not implement this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of 64-bit math on i386 causes build failures:
vdso_standalone_test_x86.c:(.text+0x101): undefined reference to `__umoddi3'
vdso_standalone_test_x86.c:(.text+0x12d): undefined reference to `__udivdi3'
Commit adb19fb66e (Documentation: add makefiles for more targets) is
now building this by default, so it's failing the kernel build entirely.
Switching the declaration from uint64_t to time_t does the right thing
and handles the x32 case automatically.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Andrey reported that on a kernel with UBSan enabled he found:
UBSan: Undefined behaviour in ../kernel/time/clockevents.c:75:34
I guess it should be 1ULL here instead of 1U:
(!ismax || evt->mult <= (1U << evt->shift)))
That's indeed the correct solution because shift might be 32.
Reported-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If userland creates a timer without specifying a sigevent info, we'll
create one ourself, using a stack local variable. Particularly will we
use the timer ID as sival_int. But as sigev_value is a union containing
a pointer and an int, that assignment will only partially initialize
sigev_value on systems where the size of a pointer is bigger than the
size of an int. On such systems we'll copy the uninitialized stack bytes
from the timer_create() call to userland when the timer actually fires
and we're going to deliver the signal.
Initialize sigev_value with 0 to plug the stack info leak.
Found in the PaX patch, written by the PaX Team.
Fixes: 5a9fa73072 ("posix-timers: kill ->it_sigev_signo and...")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Cc: <stable@vger.kernel.org> # v2.6.28+
Link: http://lkml.kernel.org/r/1412456799-32339-1-git-send-email-minipli@googlemail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jonathan writes:
First round of IIO fixes for the 3.18 cycle.
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
Felipe writes:
usb: fixes for v3.18-rc2
Here's the first set of fixes for v3.18-rc cycle. It includes
a whole bunch of bug fixes related to USB20CV and USB30CV when
running on DWC3 and MUSB. After this series, we have clean chapter 9
and MSC tests for all gadget drivers.
We also have a new PCI ID for Intel Braswell platform so they can use
DWC3 out-of-the-box.
A regression on functionfs wrt quirk_ep_out_aligned_size flag has also
been fixed.
DWC2 got a couple of fixes for the gadget role. The first of which fixes
rmmod followed by modprobe while the second makes sure to disable PHYs
before killing the regulators powering them.
These are the most important fixes worth mentioning, there are a few
other minor fixes as well.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bitmask comment says it will enable GPIO 8-14 and 16-20 for keypad use,
but it actually enables GPIO 8-11 and 13-20 due to a bit error.
Instead of masking of the "hole" at GPIO 12 (which is used for keypad
output 4) mask of the proper "hole" at GPIO 15.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the new flags argument to calls of (devm_)gpiod_get*().
Currently both forms (with or without the flags argument) are valid thanks
to transitional macros in <linux/gpio/consumer.h>. These macros will be
removed once all consumers are updated and the flags argument will become
compulsory.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Clean up the socfpga_defconfig file by doing:
make socfpga_defconfig
make
make savedefconfig
Then add the following to socfpga_defconfig:
CONFIG_SIGNALFD=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_SRAM=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_CONFIGFS_FS=y
CONFIG_PMBUS=y
CONFIG_SENSORS_PMBUS=y
CONFIG_SENSORS_LTC2978=y
CONFIG_SENSORS_LTC2978_REGULATOR=y
CONFIG_PRINTK_TIME=y
CONFIG_EXT4_FS=y
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
When modifying code, ftrace has several checks to make sure things
are being done correctly. One of them is to make sure any code it
modifies is exactly what it expects it to be before it modifies it.
In order to do so with the new trampoline logic, it must be able
to find out what trampoline a function is hooked to in order to
see if the code that hooks to it is what's expected.
The logic to find the trampoline from a record (accounting descriptor
for a function that is hooked) needs to only look at the "old_hash"
of an ops that is being modified. The old_hash is the list of function
an ops is hooked to before its update. Since a record would only be
pointing to an ops that is being modified if it was already hooked
before.
Currently, it can pick a modified ops based on its new functions it
will be hooked to, and this picks the wrong trampoline and causes
the check to fail, disabling ftrace.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace: squash into ordering of ops for modification
The code that checks for trampolines when modifying function hooks
tests against a modified ops "old_hash". But the ops old_hash pointer
is not being updated before the changes are made, making it possible
to not find the right hash to the callback and possibly causing
ftrace to break in accounting and disable itself.
Have the ops set its old_hash before the modifying takes place.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
git commit b4f0d3755c was very very dumb.
It was writing over %esp/pt_regs semi-randomly on i686 with the expected
"system can't boot" results. As noted in:
https://bugs.freedesktop.org/show_bug.cgi?id=85277
This patch stops fscking with pt_regs. Instead it sets up the registers
for the call to __audit_syscall_entry in the most obvious conceivable
way. It then does just a tiny tiny touch of magic. We need to get what
started in PT_EDX into 0(%esp) and PT_ESI into 4(%esp). This is as easy
as a pair of pushes.
After the call to __audit_syscall_entry all we need to do is get that
now useless junk off the stack (pair of pops) and reload %eax with the
original syscall so other stuff can keep going about it's business.
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Link: http://lkml.kernel.org/r/1414037043-30647-1-git-send-email-eparis@redhat.com
Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch brings back the makefile called testptp.mk which was removed
in commit adb19fb66e (Documentation: add makefiles for more targets).
While the idea of that commit was to improve build coverage of the
examples, the new Makefile is unable to cross compile the testptp program.
In contrast, the deleted makefile was able to do this just fine.
This patch fixes the regression by restoring the original makefile.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a system with NUMA configuration we want to enforce that the accelerator is
connected to a node with memory to avoid cross QPI memory transaction.
Otherwise there is no point in using the accelerator as the encryption in
software will be faster.
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update two records for ALC283 for restore default value.
[The update doesn't seem to have high impact on the existing machines,
but it fixes possible issues, especially expected in BIOS changes on
new machines, according to Realtek -- tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update default value for ALC282 for COEF.
[The update doesn't seem to have high impact on the existing machines,
but it fixes possible issues, especially expected in BIOS changes on
new machines, according to Realtek -- tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel should reserve enough room in the skb so that the DONE
message can always be appended. However, in case of e.g. new attribute
erronously not being size-accounted for, __nfulnl_send() will still
try to put next nlmsg into this full skbuf, causing the skb to be stuck
forever and blocking delivery of further messages.
Fix issue by releasing skb immediately after nlmsg_put error and
WARN() so we can track down the cause of such size mismatch.
[ fw@strlen.de: add tailroom/len info to WARN ]
Signed-off-by: Houcheng Lin <houcheng@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
don't try to queue payloads > 0xffff - NLA_HDRLEN, it does not work.
The nla length includes the size of the nla struct, so anything larger
results in u16 integer overflow.
This patch is similar to
9cefbbc9c8 (netfilter: nfnetlink_queue: cleanup copy_range usage).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently neither account for the nlattr size, nor do we consider
the size of the trailing NLMSG_DONE when allocating nlmsg skb.
This can result in nflog to stop working, as __nfulnl_send() re-tries
sending forever if it failed to append NLMSG_DONE (which will never
work if buffer is not large enough).
Reported-by: Houcheng Lin <houcheng@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 462fb2af97
bridge : Sanitize skb before it enters the IP stack
broke when IP options are actually used because it mangles the
skb as if it entered the IP stack which is wrong because the
bridge is supposed to operate below the IP stack.
Since nobody has actually requested for parsing of IP options
this patch fixes it by simply reverting to the previous approach
of ignoring all IP options, i.e., zeroing the IPCB.
If and when somebody who uses IP options and actually needs them
to be parsed by the bridge complains then we can revisit this.
Reported-by: David Newall <davidn@davidnewall.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If power management is disabled these functions become unused, so there
is no reason to build them. This fixes a couple of build warnings when
PM(_SLEEP,_RUNTIME) is not enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If power management is disabled these function become unused, so there
is no reason to build them. This fixes a couple of build warnings when
PM(_SLEEP,_RUNTIME) is not enabled.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). However, there
are still some references to that symbol left, fix that by
substituting them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: <stable@vger.kernel.org> # for 3.17
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When user requests V4L2_MEMORY_MMAP type buffers, the videobuf-core
will assign the corresponding offset to the 'boff' field of the
videobuf_buffer for each requested buffer sequentially. Later, user
may call mmap() to map one or all of the buffers with the 'offset'
parameter which is equal to its 'boff' value. Obviously, the 'offset'
value is only used to find the matched buffer instead of to be the
real offset from the buffer's physical start address as used by
vm_iomap_memory(). So, in some case that if the offset is not zero,
vm_iomap_memory() will fail.
Signed-off-by: Fancy Fang <chen.fang@freescale.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
tw68 doesn't use i2c at all, so remove this bogus dependency to prevent
this warning:
warning: (CAN_PEAK_PCIEC && SFC && IGB && VIDEO_TW68 && DRM && FB_DDC && FB_VIA) selects I2C_ALGOBIT which has unmet direct dependencies (I2C)
CC [M] drivers/i2c/algos/i2c-algo-bit.o
../drivers/i2c/algos/i2c-algo-bit.c: In function 'i2c_bit_add_bus':
../drivers/i2c/algos/i2c-algo-bit.c:658:33: error: 'i2c_add_adapter' undeclared (first use in this function)
../drivers/i2c/algos/i2c-algo-bit.c:658:33: note: each undeclared identifier is reported only once for each function it appears in
../drivers/i2c/algos/i2c-algo-bit.c: In function 'i2c_bit_add_numbered_bus':
../drivers/i2c/algos/i2c-algo-bit.c:664:33: error: 'i2c_add_numbered_adapter' undeclared (first use in this function)
../drivers/i2c/algos/i2c-algo-bit.c: In function 'i2c_bit_add_bus':
../drivers/i2c/algos/i2c-algo-bit.c:659:1: warning: control reaches end of non-void function [-Wreturn-type]
../drivers/i2c/algos/i2c-algo-bit.c: In function 'i2c_bit_add_numbered_bus':
../drivers/i2c/algos/i2c-algo-bit.c:665:1: warning: control reaches end of non-void function [-Wreturn-type]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
See include/linux/interrupt.h:
"This flag is a NOOP and scheduled to be removed"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
fmdrv_common.c: In function 'fm_download_firmware':
fmdrv_common.c:1259:2: warning: format '%d' expects argument of type 'int', but argument 3 has type 'size_t' [-Wformat=]
fmdbg("Firmware(%s) length : %d bytes\n", fw_name, fw_entry->size);
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sparse got a fix for that. Also, it is suspected that reverting
this patch might cause compilation breakages on userspace. So,
revert it.
This reverts commit 5c2cacc102.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull perf/urgent fix from Arnaldo Carvalho de Melo:
- Fix 'perf diff' initialization, calling the recently added hists__init()
function so that extra space is allocated per perf_evsel for the hists storage
that it also uses, just like report and top. (Kan Liang)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixed the return value on failure. status variable
is set to 0 at usb_assign_descriptors call and the same is
returned on error which is incorrect.
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes probe function to match the pattern used elsewhere in
the driver, where power regulators are turned off as the last element in
the device shutdown procedure.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed usb_free_all_descriptors in the bind functions, which
results in double-free corruption of the descriptors on error path.
The usb descriptors are allocated by usb_assign_descriptors.
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_stop() should clear ->driver pointer unconditionally to let the UDC
framework to work correctly with both registering/unregistering gadgets
and enabling/disabling gadgets by writing to
/sys/class/udc/*hsotg/soft_connect interface.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
while compiling integer err was showing as a set but unused variable.
elevator_init_fn can be either cfq_init_queue or deadline_init_queue
or noop_init_queue.
all three of these functions are returning -ENOMEM if they fail to
allocate the queue.
so we should actually be returning the error code rather than
returning 0 always.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was found attached to the BCM47081A0 SoC. Log:
bcma: bus0: Found chip with id 43228, rev 0x00 and package 0x08
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver logs a message when the default branch of switch statements are
taken. Such information is useful when debugging, but these log items should
not be seen for standard usage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2101e533f4 ("bcma: register bcma as device tree driver")
introduces a hard dependency on OF_ADDRESS into the bcma driver.
OF_ADDRESS is specifically disabled for the sparc architecture.
This results in the following error when building sparc64:allmodconfig.
drivers/bcma/main.c: In function 'bcma_of_find_child_device':
drivers/bcma/main.c:150:3: error: implicit declaration of function 'of_translate_address'
Fixes: 2101e533f4 ("bcma: register bcma as device tree driver")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unknown operation numbers are caught in nfsd4_decode_compound() which
sets op->opnum to OP_ILLEGAL and op->status to nfserr_op_illegal. The
error causes the main loop in nfsd4_proc_compound() to skip most
processing. But nfsd4_proc_compound also peeks ahead at the next
operation in one case and doesn't take similar precautions there.
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Xtensa improvements for 3.18:
- add seccomp, getrandom, and memfd_create syscalls;
- add defconfigs for KC705 and SMP LX200;
- fix ISS and xtfpga Kconfig dependencies so that more randconfigs
are buildable;
- fix umount syscall;
- implement pgprot_noncached.
The unioned u32 is used for clearing etc. Having the number of
bitfield bits add up to more than 32 is broken, even if benign.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse was giving the following warning:
warning: context imbalance in 's3c_hsotg_ep_enable'
- different lock contexts for basic block
we were returning ENOMEM while still holding the spinlock.
The sparse warning was fixed by releasing the spinlock before return.
Cc: <stable@vger.kernel.org> # v3.17
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in
|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
echo mem > /sys/power/state
then you go boom
|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)
because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 468bcc2a2c ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a2c "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A request allocated from e.g. ep1out cannot
be queued to any other endpoint. This bug has
been in f_loopback at least since mid-2011 and
since nobody has really screamed about it, we're
not backporting to any stable kernels.
Debugged with MUSB since that's the only controller
which complains about this case.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The commit '2e4c7553cd usb: gadget: f_fs: add aio support' broke the
quirk implemented to align buffer size to maxpacketsize on out endpoint.
As result, functionfs does not work on Intel platforms using dwc3 driver
(i.e. Bay Trail and Merrifield). This patch fixes the issue.
This code is based on a previous Qiuxu's patch.
Fixes: 2e4c7553cd (usb: gadget: f_fs: add aio support)
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During FunctionFS bind, ffs_data_get() function was called twice
(in functionfs_bind() and in ffs_do_functionfs_bind()), while on unbind
ffs_data_put() was called once (in functionfs_unbind() function).
In result refcount never reached value 0, and ffs memory resources has
been never released.
Since ffs_data_get() call in ffs_do_functionfs_bind() is redundant
and not neccessary, we remove it to have equal number of gets ans puts,
and free allocated memory after refcount reach 0.
Fixes: 5920cda (usb: gadget: FunctionFS: convert to new function
interface with backward compatibility)
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `xudc_done':
udc-xilinx.c:(.text+0x54f4d2): undefined reference to `usb_gadget_unmap_request'
drivers/built-in.o: In function `xudc_dma_send':
udc-xilinx.c:(.text+0x54f9f8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `xudc_read_fifo':
udc-xilinx.c:(.text+0x54ff4a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `xudc_ep_queue':
udc-xilinx.c:(.text+0x550e7c): undefined reference to `usb_gadget_map_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 02dae36aa6.
That commit is bogus in two ways:
1) There's no way dwc3-omap's ->suspend() can cause any effect
on xhci's ->suspend(). Linux device driver model guarantees
that a parent's ->suspend() will only be called after all
children are suspended. dwc3-omap is the parent of the
parent of xhci.
2) When implementing Deep Sleep states where context is lost,
USBOTGSS_IRQ0 register, well, looses context so we
_must_ rewrite it otherwise core IRQs will never be
reenabled and USB will appear to be dead.
Fixes: 02dae36 (usb: dwc3: dwc3-omap: Disable/Enable only
wrapper interrupts in prepare/complete)
Cc: <stable@vger.kernel.org> # v3.17
Cc: George Cherian <george.cherian@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to USB 2.0 ECN Errata for Link Power
Management (USB2-LPM-Errata-final.pdf), BESL
must be enabled if LPM is enabled.
This helps with USB30CV TD 9.21 LPM L1
Suspend Resume Test.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit c58d80f52 ("usb: musb: Ensure that cppi41 timer gets armed on
premature DMA TX irq") fixed hrtimer scheduling bug. There is one left
which does not trigger that often.
The following scenario is still possible:
lock(&x->lock);
hrtimer_start(&x->t);
unlock(&x->lock);
expires:
t->function();
lock(&x->lock);
lock(&x->lock); if (!hrtimer_queued(&x->t))
hrtimer_start(&x->t);
unlock(&x->lock);
if (!list_empty(x->early_tx_list))
ret = HRTIMER_RESTART;
-> hrtimer_forward_now(...)
} else
ret = HRTIMER_NORESTART;
unlock(&x->lock);
and the timer callback returns HRTIMER_RESTART for an armed timer. This
is wrong and we run into the BUG_ON() in __run_hrtimer().
This can happens on SMP or PREEMPT-RT.
The patch fixes the problem by only starting the timer if the timer is
not yet queued.
Cc: stable@vger.kernel.org
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: collected information and created a patch + description based
on it]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Section 8.5.3.2 of the USB 2.0 specification,
a USB device must terminate a Data Phase with either a
short packet or a ZLP (if the previous transfer was
a multiple of wMaxPacketSize).
For reference, here's what the USB 2.0 specification, section
8.5.3.2 says:
"
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase
in which the host requests more data than is contained
in the specified data structure. When all of the data
structure is returned to the host, the function should
indicate that the Data stage is ended by returning a
packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of
wMaxPacketSize for the pipe, the function will return
a zero-length packet to indicate the end of the Data
stage.
"
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit dd56af42bd (rcu: Eliminate deadlock between CPU hotplug and
expedited grace periods) was incomplete. Although it did eliminate
deadlocks involving synchronize_sched_expedited()'s acquisition of
cpu_hotplug.lock via get_online_cpus(), it did nothing about the similar
deadlock involving acquisition of this same lock via put_online_cpus().
This deadlock became apparent with testing involving hibernation.
This commit therefore changes put_online_cpus() acquisition of this lock
to be conditional, and increments a new cpu_hotplug.puts_pending field
in case of acquisition failure. Then cpu_hotplug_begin() checks for this
new field being non-zero, and applies any changes to cpu_hotplug.refcount.
Reported-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Borislav Petkov <bp@suse.de>
Currently, we can't call opal wrappers from modules when using the LE
ABIv2, which requires a TOC init. If we do we'll try and load the opal
entry point using the wrong toc and probably explode or worse jump to
the wrong address.
Nothing in upstream is making opal calls from a module, but we do export
one of the wrappers so we should fix this anyway.
This change uses the _GLOBAL_TOC() macro (rather than _GLOBAL) for the
opal wrappers, so that we can do non-local calls to them.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When sg_scsi_ioctl() fails to prepare request to submit in
blk_rq_map_kern() we jump to a label where we just end up copying
(luckily zeroed-out) kernel buffer to userspace instead of reporting
error. Fix the problem by jumping to the right label.
CC: Jens Axboe <axboe@kernel.dk>
CC: linux-scsi@vger.kernel.org
CC: stable@vger.kernel.org
Coverity-id: 1226871
Signed-off-by: Jan Kara <jack@suse.cz>
Fixed up the, now unused, out label.
Signed-off-by: Jens Axboe <axboe@fb.com>
total_data_buflen is used by netvsc_send() to decide if a packet can be put
into send buffer. It should also include the size of RNDIS message before the
Ethernet frame. Otherwise, a messge with total size bigger than send_section_size
may be copied into the send buffer, and cause data corruption.
[Request to include this patch to the Stable branches]
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2014-10-22
The following series of patches includes fixes to the driver.
- Properly handle feature changes via ethtool by using correctly sized
variables
- Perform proper napi packet counting and budget checking
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed. Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate. Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.
Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d240478 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit "net: Save TX flow hash in sock and set in skbuf on xmit"
introduced the inet_set_txhash() and ip6_set_txhash() routines to calculate
and record flow hash(sk_txhash) in the socket structure. sk_txhash is used
to set skb->hash which is used to spread flows across multiple TXQs.
But, the above routines are invoked before the source port of the connection
is created. Because of this all outgoing connections that just differ in the
source port get hashed into the same TXQ.
This patch fixes this problem for IPv4/6 by invoking the the above routines
after the source port is available for the socket.
Fixes: b73c3d0e4("net: Save TX flow hash in sock and set in skbuf on xmit")
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() maybe change skb->data and make nh and exthdr pointer
oboslete, so recompute the nd and exthdr
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After interface restart (eg: after link disconnection/reconnection), the bridge
function doesn't work anymore. This is due to the promiscuous mode being cleared
by the restart.
The mac-fcc already includes code to set the promiscuous mode back during the restart.
This patch adds the same handling to mac-fec and mac-scc.
Tested with bridge function on MPC885 with FEC.
Reported-by: Germain Montoies <germain.montoies@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the TSC is unusable or disabled, then this patch fixes:
- Confusion while trying to clear old APIC interrupts.
- Division by zero and incorrect programming of the TSC deadline
timer.
This fixes boot if the CPU has a TSC deadline timer but a missing or
broken TSC. The failure to boot can be observed with qemu using
-cpu qemu64,-tsc,+tsc-deadline
This also happens to me in nested KVM for unknown reasons.
With this patch, I can boot cleanly (although without a TSC).
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Bandan Das <bsd@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/e2fa274e498c33988efac0ba8b7e3120f7f92d78.1413393027.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It also uses hists/hist_entries, hists__init() should be called before
creating any evsels.
Otherwise no extra space will be allocated per perf_evsel nor this space
will be initialized when allocating a new perf_evsel instance, resulting
in reads/writes to non allocated space, oops. Fix it.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Link: http://lkml.kernel.org/r/1414004561-22096-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit 75897d60 (hugetlb: allow sticky directory mount option) added
support for mounting hugetlbfs with sticky option set, like /tmp is
usually mounted, but forgot to document that.
Acked-by: Ken Chen <kenchen@google.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The crafted header start address is from a driver supplied buffer, which
one can reasonably expect to be aligned on a 4-bytes boundary.
However ATM the TSO helper API is only used by ethernet drivers and
the tcp header will then be aligned to a 2-bytes only boundary from the
header start address.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_count and insert_count can wrap around, making > check invalid.
Fixes: 70b33fb0dd ("sfc: add support for
skb->xmit_more").
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've got a harmless warning when running make cleandocs on an already
cleaned tree:
Documentation/DocBook/media/Makefile:28: recipe for target 'cleanmediadocs' failed
make[1]: [cleanmediadocs] Error 1 (ignored)
Suppress this by passing -f to rm.
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When creation of queues fails in init_driver_queues(), we free the
queues. But null_add_dev() doesn't test for this failure and continues
with the setup leading to strange consequences, likely oops. Fix the
problem by testing whether init_driver_queues() failed and do proper
error cleanup.
Coverity-id: 1148005
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ->ip_set_list[] array is initialized in ip_set_net_init() and it
has ->ip_set_max elements so this check should be >= instead of >
otherwise we are off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a port that was used to listen for inbound connections gets closed
and reused for outgoing connections (like rsh ends up doing for stderr
flow), current we may reject the SYN/ACK packet for the new connection
because tcp_conntracks states forbirds a port to become a client while
there is still a TIME_WAIT entry in there for it.
As TCP may expire the TIME_WAIT socket in 60s and conntrack's timeout
for it is 120s, there is a ~60s window that the application can end up
opening a port that conntrack will end up blocking.
This patch fixes this by simply allowing such state transition: if we
see a SYN, in TIME_WAIT state, on REPLY direction, move it to sSS. Note
that the rest of the code already handles this situation, more
specificly in tcp_packet(), first switch clause.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use strncpy() instead of strcpy(). That's not a security issue, as the
source buffer is taken from DT nodes, but we should still enforce bound
checks. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the input PGA to work correctly the ALC clock needs to be active.
Otherwise volume changes are not applied.
Fixes: dab464b60b ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits
from 4 to 1. The bit 4 is 'reserved', so this probably should not cause
any issues, but it's better to fix it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.
Fix the register dump.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 90419cfcb5,
"USB: kobil_sct: fix control requests without data stage", removed
the bogus data buffer arguments, but still allocate transfer
buffers which are not used.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb disables all the overlays when freeing resources, but it should
also remove those overlays from overlay managers.
Not doing so causes a crash if omapfb is unbound and bound, or omapfb
module is removed and loaded, while keeping omapdss around.
Fix this by calling unset_manager() for all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb is shutting down, it will disable all the overlays. However,
instead of actually disabling all the overlays, it disables only all the
overlays that are currently attached to framebuffers.
On OMAP4+, this leaves the fourth overlay left enabled.
Fix the loop so that we actually go through all the overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should wait for any pending updates when an overlay manager is
about to be disabled, because the updates will never be finished if the
manager is disabled too early.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we leave __exit annotation, driver can't be unbound
through sysfs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.
Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
without MODULE_ALIAS(), omapfb won't get loaded
automatically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add VID/PID for Telit LE910 modem. Interfaces description is almost the
same than LE920, except that the qmi interface is number 2 (instead than
5).
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add new IDs for the Xsens Awinda Station and Awinda Dongle.
While at it, order the definitions by PID and add a logical separation
between devices using Xsens' VID and those using FTDI's VID.
Cc: <stable@vger.kernel.org>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
While the hash function used by the revoke hashtable is good somewhere else,
it's not really good here.
The default hash shift (8) means that one third of the hashing function
gets lost (and is undefined anyways (8 - 12 = negative shift)):
"(block << (hash_shift - 12))) & (table->hash_size - 1)"
Instead, just use the kernel's generic hash function that gets used everywhere
else.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Enable Silicon Labs Ember VID chips to enumerate with the cp210x usb serial
driver. EM358x devices operating with the Ember Z-Net 5.1.2 stack may now
connect to host PCs over a USB serial link.
Signed-off-by: Nathaniel Ting <nathaniel.ting@silabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Due to a switched left and right side of an assignment,
dquot_writeback_dquots() never returned error. This could result in
errors during quota writeback to not be reported to userspace properly.
Fix it.
CC: stable@vger.kernel.org
Coverity-id: 1226884
Signed-off-by: Jan Kara <jack@suse.cz>
The check whether quota format is set even though there are no
quota files with journalled quota is pointless and it actually
makes it impossible to turn off journalled quotas (as there's
no way to unset journalled quota format). Just remove the check.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Since strsep is used to tokenize the options string, after each option
match the code should use "continue" to get the next token from strsep.
This patch applies this pattern consistently.
Previously, for "scrollback:" and "map:" the parse code would return
(unconditionally: strsep ensures *options != ','), causing any
following option to be ignored, while for "vc:" the parse code would
go on to parse further options within the same token, which could lead
to invalid input being accepted.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch wires up the new syscall sys_bpf() on powerpc.
Passes the tests in samples/bpf:
#0 add+sub+mul OK
#1 unreachable OK
#2 unreachable2 OK
#3 out of range jump OK
#4 out of range jump2 OK
#5 test1 ld_imm64 OK
#6 test2 ld_imm64 OK
#7 test3 ld_imm64 OK
#8 test4 ld_imm64 OK
#9 test5 ld_imm64 OK
#10 no bpf_exit OK
#11 loop (back-edge) OK
#12 loop2 (back-edge) OK
#13 conditional loop OK
#14 read uninitialized register OK
#15 read invalid register OK
#16 program doesn't init R0 before exit OK
#17 stack out of bounds OK
#18 invalid call insn1 OK
#19 invalid call insn2 OK
#20 invalid function call OK
#21 uninitialized stack1 OK
#22 uninitialized stack2 OK
#23 check valid spill/fill OK
#24 check corrupted spill/fill OK
#25 invalid src register in STX OK
#26 invalid dst register in STX OK
#27 invalid dst register in ST OK
#28 invalid src register in LDX OK
#29 invalid dst register in LDX OK
#30 junk insn OK
#31 junk insn2 OK
#32 junk insn3 OK
#33 junk insn4 OK
#34 junk insn5 OK
#35 misaligned read from stack OK
#36 invalid map_fd for function call OK
#37 don't check return value before access OK
#38 access memory with incorrect alignment OK
#39 sometimes access memory with incorrect alignment OK
#40 jump test 1 OK
#41 jump test 2 OK
#42 jump test 3 OK
#43 jump test 4 OK
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
[mpe: test using samples/bpf]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the check of CONFIG_PPC_SUBPAGE_PROT when deciding if
is_hugepage_only_range() is extern or inline. The extern version is in
slice.c and is built if CONFIG_PPC_MM_SLICES=y.
There was no build break possible because CONFIG_PPC_SUBPAGE_PROT is
only selectable under conditions which also mean CONFIG_PPC_MM_SLICES
will be selected.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/mm/slice.c:704:5: error: expected identifier or ‘(’ before numeric constant
int is_hugepage_only_range(struct mm_struct *mm, unsigned long addr,
^
make[1]: *** [arch/powerpc/mm/slice.o] Error 1
make: *** [arch/powerpc/mm/slice.o] Error 2
This got introduced via 1217d34b53
"powerpc: Ensure global functions include their prototype". We
started including linux/hugetlb.h with that patch and now we have
#define is_hugepage_only_range(mm, addr, len) 0
with hugetlbfs disabled.
Fixes: 1217d34b53 ("powerpc: Ensure global functions include their prototype")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use netdev_alloc_pcpu_stats to allocate percpu stats and initialize syncp.
Fixes: 22e0f8b932 "net: sched: make bstats per cpu and estimator RCU safe"
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while comparing for verifier state equivalency the comparison
was missing a check for uninitialized register.
Make sure it does so and add a testcase.
Fixes: f1bca824da ("bpf: add search pruning optimization to verifier")
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synchronize_rcu() in netlink_release() introduces unacceptable
latency. Reintroduce minimal lookup so we can drop the
synchronize_rcu() until socket destruction has been RCUfied.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is introduced by commit 764f612c6c3c231b(blk-merge:
don't compute bi_phys_segments from bi_vcnt for cloned bio),
and merge is needed if number of current segment isn't less than
max segments.
Strictly speaking, bio->bi_vcnt shouldn't be used here since
it may not be accurate in cases of both cloned bio or bio cloned
from, but bio_segments() is a bit expensive, and bi_vcnt is still
the biggest number, so the approach should work.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
m25p80's device ID table is now spi_nor_ids, defined in spi-nor. The
MODULE_DEVICE_TABLE() macro doesn't work with extern definitions, but
its use was also removed at the same time. Now if m25p80 is built as
a module it doesn't get the necessary aliases to be loaded
automatically.
A clean solution to this will involve defining the list of device
IDs in spi-nor.h and removing struct spi_device_id from the spi-nor
API, but this is quite a large change.
As a quick fix suitable for stable, copy the device IDs back into
m25p80.
Fixes: 03e296f613 ("mtd: m25p80: use the SPI nor framework")
Cc: <stable@vger.kernel.org> # 3.16.x: 32f1b7c835: mtd: move support for struct flash_platform_data into m25p80
Cc: <stable@vger.kernel.org> # 3.16.x: 90e55b3812: mtd: m25p80: get rid of spi_get_device_id
Cc: <stable@vger.kernel.org> # 3.16.x: 70f3ce0510: mtd: spi-nor: make spi_nor_scan() take a chip type name, not spi_device_id
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When quiet_error applies rate limiting to buffer_io_error calls, what the
they apply to is unclear because the name is so generic, particularly
if the messages are interleaved with others:
[ 1936.063572] quiet_error: 664293 callbacks suppressed
[ 1936.065297] Buffer I/O error on dev sdr, logical block 257429952, lost async page write
[ 1936.067814] Buffer I/O error on dev sdr, logical block 257429953, lost async page write
Also, the function uses printk_ratelimit(), although printk.h includes a
comment advising "Please don't use... Instead use printk_ratelimited()."
Change buffer_io_error to check the BH_Quiet bit itself, drop the
printk_ratelimit call, and print using printk_ratelimited.
This makes the messages look like:
[ 387.208839] buffer_io_error: 676394 callbacks suppressed
[ 387.210693] Buffer I/O error on dev sdr, logical block 211291776, lost async page write
[ 387.213432] Buffer I/O error on dev sdr, logical block 211291777, lost async page write
Signed-off-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
buffer.c uses two printk calls to print these messages:
[67353.422338] Buffer I/O error on device sdr, logical block 212868488
[67353.422338] lost page write due to I/O error on sdr
In a busy system, they may be interleaved with other prints,
losing the context for the second message. Merge them into
one line with one printk call so the prints are atomic.
Also, differentiate between async page writes, sync page writes, and
async page reads.
Also, shorten "device" to "dev" to match the block layer prints:
[67353.467906] blk_update_request: critical target error, dev sdr, sector
1707107328
Also, use %llu rather than %Lu.
Resulting prints look like:
[ 1356.437006] blk_update_request: critical target error, dev sdr, sector 1719693992
[ 1361.383522] quiet_error: 659876 callbacks suppressed
[ 1361.385816] Buffer I/O error on dev sdr, logical block 256902912, lost async page write
[ 1361.385819] Buffer I/O error on dev sdr, logical block 256903644, lost async page write
Signed-off-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Locking dependency detected below possible unsafe locking scenario:
CPU0 CPU1
T0: tipc_named_rcv() tipc_rcv()
T1: [grab nametble write lock]* [grab node lock]*
T2: tipc_update_nametbl() tipc_node_link_up()
T3: tipc_nodesub_subscribe() tipc_nametbl_publish()
T4: [grab node lock]* [grab nametble write lock]*
The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the updating of the name table after link state named out of node
lock, the reverse order of holding locks will be eliminated, and
as a result, the deadlock risk.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan says:
====================
enic: Bug fixes
This series fixes the following problem.
Please apply this to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 4.9 complains if we take the difference of two pointers, and it's
printed with "%d". Fix this by using the proper flag - "t" for
ptrdiff_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
vdso_standalone_test_x86 needs -lgcc_s to build succesfully on 32bit.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
[ Fixed missing separator issue reported by Paul Bolle <pebolle@tiscali.nl> ]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When posting a patch series that includes both code implementing a
Device Tree binding and its associated documentation, the DT docs
should come in the series before the implementation.
This not only avoids checkpatch.pl to complain about undocumented
bindings but also makes the review process easier.
Document this convention since it may not be obvious.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Correct a sentence in Documentation/ABI/testing/sysfs-ibft.
Signed-off-by: WANG Chao <chaowang@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The dm-raid superblock (struct dm_raid_superblock) is padded to 512
bytes and that size is being used to read it in from the metadata
device into one preallocated page.
Reading or writing this on a 512-byte sector device works fine but on
a 4096-byte sector device this fails.
Set the dm-raid superblock's size to the logical block size of the
metadata device, because IO at that size is guaranteed too work. Also
add a size check to avoid silent partial metadata loss in case the
superblock should ever grow past the logical block size or PAGE_SIZE.
[includes pointer math fix from Dan Carpenter]
Reported-by: "Liuhua Wang" <lwang@suse.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
We added this new estimator function but forgot to hook it up. The
effect is that NFSv4.1 (and greater) won't do zero-copy reads.
The estimate was also wrong by 8 bytes.
Fixes: ccae70a9ee "nfsd4: estimate sequence response size"
Cc: stable@vger.kernel.org
Reported-by: Chuck Lever <chucklever@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
My static checker complains that "i" could be one element beyond the end
of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The config structs used for DVBSky T9580 were not initialized. This patch fixes that.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit e93e7fd9f5 ("v4l2: uvcvideo: Allow
using larger buffers") reworked the buffer size sanity check at buffer
completion time to use the frame size instead of the allocated buffer
size. However, it introduced two bugs in doing so:
- it assigned the allocated buffer size to the frame_size field, instead
of assigning the correct frame size
- it performed the assignment in the S_FMT handler, resulting in the
frame_size field being uninitialized if the userspace application
doesn't call S_FMT.
Fix both issues by removing the frame_size field and validating the
buffer size against the UVC video control dwMaxFrameSize.
Fixes: e93e7fd9f5 ("v4l2: uvcvideo: Allow using larger buffers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The random_line buffer must be twice the maximum width, but it only allocated
the maximum width, so it was only half the size it needed to be.
Surprisingly I never saw the kernel fail on this, but the same TPG code used in
qv4l2 crashed and valgrind helped me track this bug down.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this daily build warning:
In file included from build/media_build/v4l/em28xx-core.c:35:0:
build/media_build/v4l/em28xx-core.c: In function 'em28xx_audio_setup':
build/media_build/v4l/em28xx.h:798:2: warning: 'vid' may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(KERN_INFO "%s: "fmt,\
^
build/media_build/v4l/em28xx-core.c:507:6: note: 'vid' was declared here
u32 vid;
^
As far as I can tell 'vid' can not really be used uninitialized here, but the code
is sufficiently complex that apparently gcc can't figure that out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that loaded modules are const char strings so we don't
load arbitrary modules in the future, nor allow for format string
leaks in the module request call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix media DocBook build errors by re-adding the orderedlist tag
and putting back the section tags lost during merge.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Linux 3.18-rc1
* tag 'v3.18-rc1': (9167 commits)
Linux 3.18-rc1
MAINTAINERS: corrected bcm2835 search
Net: DSA: Fix checking for get_phy_flags function
sparc64: Do not define thread fpregs save area as zero-length array.
sparc64: Fix corrupted thread fault code.
MAINTAINERS: Become the docs maintainer
x86,kvm,vmx: Preserve CR4 across VM entry
ipv6: fix a potential use after free in sit.c
ipv6: fix a potential use after free in ip6_offload.c
ipv4: fix a potential use after free in gre_offload.c
tcp: fix build error if IPv6 is not enabled
futex: Ensure get_futex_key_refs() always implies a barrier
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
...
This config allows running SMP-enabled bitstream on LX200 board.
NFS or FLASH rootfs, minimal debug, up to 4 cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Userspace actually passes single parameter (path name) to the umount
syscall, so new umount just fails. Fix it by requesting old umount
syscall implementation and re-wiring umount to it.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
if our list of requests is empty, return early.
There's really nothing to be done in case our
request list is empty anyway because the only
situation where we our list is empty, is when
we're transferring ZLPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On USB20CV's Interface Descriptor Test, a series
of SetInterface/GetInterface requests are issued
and gadget driver is required to always return
correct alternate setting.
In one step of the test, g_serial with f_obex
was returning the wrong value (1 instead of 0).
In order to fix this, we will now hold currently
selected alternate setting inside our struct f_obex
and just return that from our ->get_alt()
implementation.
Note that his also simplifies the code a bit.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Endpoint descriptors should pass wMaxPacketSize. Note
that this also fixes USB20CV Other Speed Endpoint
Descriptor Tests.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when our ->disable() method is called, we must
make sure to teardown all our resources, including
endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
just like any other endpoint, we must enable/disable
our video control endpoint based on calls to our
->set_alt() method.
Signed-off-by: Felipe Balbi <balbi@ti.com>
During Halt Endpoint Test, our interrupt endpoint
will be disabled, which will clear out ep->desc
to NULL. Unless we call config_ep_by_speed() again,
we will not be able to enable this endpoint which
will make us fail that test.
Fixes: f9c56cd (usb: gadget: Clear usb_endpoint_descriptor
inside the struct usb_ep on disable)
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Felipe Balbi <balbi@ti.com>
If our alternate setting has been selected, we must
return that on a subsequent Get Interface request
even if we're not streaming.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If a set_alt() to the same alternate setting that's
already selected is received, functions are required
to reset the interface state, this means we must disable
all endpoints and reenable them again.
This is also documented on our kdoc for struct usb_function
* @set_alt: (REQUIRED) Reconfigures altsettings; function drivers may
* initialize usb_ep.driver data at this time (when it is used).
* Note that setting an interface to its current altsetting resets
* interface state, and that all interfaces have a disabled state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to our Gadget Framework API documentation,
->set_halt() *must* return -EAGAIN if we have pending
transfers (on either direction) or FIFO isn't empty (on
TX endpoints).
Fix this bug so that the mass storage gadget can be used
without stall=0 parameter.
This patch should be backported to all kernels since v3.2.
Cc: <stable@vger.kernel.org> # v3.2+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of releasing the lock and calling locked
versions of our set_halt() methods, let's hold
the lock all the way through and call unlocked
versions of those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__dwc3_gadget_ep_set_halt() is the function which
handles the actual halt feature. In order to cope
with some extra cleanup comming as a follow-up patch
let's move the isochronous endpoint check there too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep0_set_halt() will be called without
locks held in some cases, so we must hold the lock
on our own. While at that, also add a version without
locks to be called in certain conditions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The commit 2111667b46 ("ARM: pxa: call debug_ll_io_init for
earlyprintk") triggers in the current kernel the attached backtrace on
PXA/tosa early in the boot time when DEBUG_LL is enabled.
It is due to overlap between uart virtual memory defined in
DEBUG_UART_VIRT and mapped by debug_ll_io_init() and peripheral bus
mapped by pxa_map_io at the same address, 0xf2100000.
As hinted by Arnd, map early virtual memory for low level debug on
address 0xf6200000, even if that means 2 virtual mappings will give
access to the pxa internal UARTs (FFUART, BTUART, STUART, ...).
------------[ cut here ]------------
kernel BUG at /home/lumag/linux/mm/vmalloc.c:1143!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.17.0-00032-g8e0d202-dirty #23
task: c062a5a8 ti: c0620000 task.ti: c0620000
PC is at vm_area_add_early+0x54/0x84
LR is at add_static_vm_early+0xc/0x60
pc : [<c03e1100>] lr : [<c03d9ef4>] psr: 800001d3
sp : c0621f04 ip : c03efa74 fp : c03edf84
r10: c0637e98 r9 : 40000001 r8 : c03da57c
r7 : c3ffcfb0 r6 : 00000000 r5 : c3ffcfb0 r4 : 02000000
r3 : c3ffcfd8 r2 : f2100000 r1 : f4000000 r0 : c3ffcfb0
Flags: Nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 00007977 Table: a0004000 DAC: 00000017
Process swapper (pid: 0, stack limit = 0xc06201c8)
Stack: (0xc0621f04 to 0xc0622000)
1f00: c3ffcfd8 40000001 c3ffcfd8 c03ee08c c03da570 c03db90c c0637d24
1f20: 00000000 c03ec7cc c066e654 a0700000 000a0700 c03db914 c03db90c c03daf84
1f40: 00000000 000a0000 c0000000 c03ec7cc 000a0700 c0700000 ffff1000 000a3fff
1f60: 00001000 00000007 00000000 c03ec7cc c0008000 c03ed748 c0621fd4 c03d5d18
1f80: 69052d00 a03ec48c 00000000 c03d8ad0 0000006c 00007977 c036c6e8 00000001
1fa0: c0621fd4 c03ed744 c0628000 a0004000 69052d00 a03ec48c 00000000 c03d68d4
1fc0: 00000000 00000000 00000000 00000000 00000000 c03ed748 c0649894 c062801c
1fe0: c03ed744 c062b2f0 a0004000 69052d00 a03ec48c a0008040 00000000 00000000
[<c03e1100>] (vm_area_add_early) from [<c03d9ef4>] (add_static_vm_early+0xc/0x60)
[<c03d9ef4>] (add_static_vm_early) from [<c03da570>] (iotable_init.part.6+0xa8/0xb4)
[<c03da570>] (iotable_init.part.6) from [<c03db914>] (pxa25x_map_io+0x8/0x24)
[<c03db914>] (pxa25x_map_io) from [<c03daf84>] (paging_init+0x744/0x8d8)
[<c03daf84>] (paging_init) from [<c03d8ad0>] (setup_arch+0x354/0x608)
[<c03d8ad0>] (setup_arch) from [<c03d68d4>] (start_kernel+0xa8/0x3dc)
[<c03d68d4>] (start_kernel) from [<a0008040>] (0xa0008040)
Code: e5904008 e0811004 e1520001 2a000005 (e7f001f2)
---[ end trace f24b6c88ae00fa9a ]---
Kernel panic - not syncing: Attempted to kill the idle task!
---[ end Kernel panic - not syncing: Attempted to kill the idle task!
Cc: <stable@vger.kernel.org>
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Florian Westphal says:
====================
net: minor gso encapsulation fixes
The following series fixes a minor bug in the gso segmentation handlers
when encapsulation offload is used.
Theoretically this could cause kernel panic when the stack tries
to software-segment such a GRE offload packet, but it looks like there
is only one affected call site (tbf scheduler) and it handles NULL
return value.
I've included a followup patch to add IS_ERR_OR_NULL checks where needed.
While looking into this, I also found that size computation of the individual
segments is incorrect if skb->encapsulation is set.
Please see individual patches for delta vs. v1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
if ->encapsulation is set we have to use inner_tcp_hdrlen and add the
size of the inner network headers too.
This is 'mostly harmless'; tbf might send skb that is slightly over
quota or drop skb even if it would have fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment has three possible return values:
1. a pointer to the first segmented skb
2. an errno value (IS_ERR())
3. NULL. This can happen when GSO is used for header verification.
However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL
and would oops when NULL is returned.
Note that these call sites should never actually see such a NULL return
value; all callers mask out the GSO bits in the feature argument.
However, there have been issues with some protocol handlers erronously not
respecting the specified feature mask in some cases.
It is preferable to get 'have to turn off hw offloading, else slow' reports
rather than 'kernel crashes'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_segment() has a 'features' argument representing offload features
available to the output path.
A few handlers, e.g. GRE, instead re-fetch the features of skb->dev and use
those instead of the provided ones when handing encapsulation/tunnels.
Depending on dev->hw_enc_features of the output device skb_gso_segment() can
then return NULL even when the caller has disabled all GSO feature bits,
as segmentation of inner header thinks device will take care of segmentation.
This e.g. affects the tbf scheduler, which will silently drop GRE-encap GSO skbs
that did not fit the remaining token quota as the segmentation does not work
when device supports corresponding hw offload capabilities.
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains netfilter fixes for your net tree,
they are:
1) Fix missing MODULE_LICENSE() in the new nf_reject_ipv{4,6} modules.
2) Restrict nat and masq expressions to the nat chain type. Otherwise,
users may crash their kernel if they attach a nat/masq rule to a non
nat chain.
3) Fix hook validation in nft_compat when non-base chains are used.
Basically, initialize hook_mask to zero.
4) Make sure you use match/targets in nft_compat from the right chain
type. The existing validation relies on the table name which can be
avoided by
5) Better netlink attribute validation in nft_nat. This expression has
to reject the configuration when no address and proto configurations
are specified.
6) Interpret NFTA_NAT_REG_*_MAX if only if NFTA_NAT_REG_*_MIN is set.
Yet another sanity check to reject incorrect configurations from
userspace.
7) Conditional NAT attribute dumping depending on the existing
configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM an HT rc_stats line is 106 chars.
Times 8(MCS_GROUP_RATES)*3(SS)*2(GI)*2(BW) + CCK(4), i.e. x100, this is
well above the current 8192 - sizeof(*ms) currently allocated.
Fix this by squeezing the output as follows (not that we're short on
memory but this also improves readability and range, the new format adds
one more digit to *ok/*cum and ok/cum):
- Before (HT) (106 ch):
type rate throughput ewma prob this prob retry this succ/attempt success attempts
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0 0
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0 0
- After (75 ch):
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0( 0)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
- Align non-HT format Before (non-HT) (83 ch):
rate throughput ewma prob this prob this succ/attempt success attempts
ABCDP 6 0.0 0.0 0.0 0( 0) 0 0
54 0.0 0.0 0.0 0( 0) 0 0
- After (61 ch):
rate tpt eprob *prob *ok(*cum) ok( cum)
ABCDP 1 0.0 0.0 0.0 0( 0) 0( 0)
54 0.0 0.0 0.0 0( 0) 0( 0)
*This also adds dynamic checks for overflow, lowers the size of the
non-HT request (allowing > 30 entries) and replaces the buddy-rounded
allocations (s/sizeof(*ms) + 8192/8192).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The s6000 Xtensa support is removed from the kernel. There are no
other chips known to use this I2S controller.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO concepts are close enough to pin control that we may use
the same mailing list to discuss them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Direct irq en bit should be cleared for pads using io mode.
If not, the io based irq will never be detected.
However, this bit can sometimes be misconfigured (BIOS issue).
Force clearing of this bit in io mode and trigger a WARN.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
COMEDI_II_PCI20KC needs HAS_IOMEM, so depend on it. The related error (
with allmodconfig under um):
CC [M] drivers/staging/comedi/drivers/ii_pci20kc.o
drivers/staging/comedi/drivers/ii_pci20kc.c: In function ‘ii20k_attach’:
drivers/staging/comedi/drivers/ii_pci20kc.c:442:2: error: implicit declaration of function ‘ioremap’ [-Werror=implicit-function-declaration]
dev->mmio = ioremap(membase, II20K_SIZE);
^
drivers/staging/comedi/drivers/ii_pci20kc.c:442:12: warning: assignment makes pointer from integer without a cast [enabled by default]
dev->mmio = ioremap(membase, II20K_SIZE);
^
drivers/staging/comedi/drivers/ii_pci20kc.c: In function ‘ii20k_detach’:
drivers/staging/comedi/drivers/ii_pci20kc.c:512:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(dev->mmio);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`do_cmd_ioctl()`, the handler for the `COMEDI_CMD` ioctl can incorrectly
call the Comedi subdevice's `do_cmd()` handler with a NULL channel list
pointer. This is a regression as the `do_cmd()` handler has never been
expected to deal with that, leading to a kernel OOPS when it tries to
dereference it.
A NULL channel list pointer is allowed for the `COMEDI_CMDTEST` ioctl,
handled by `do_cmdtest_ioctl()` and the subdevice's `do_cmdtest()`
handler, but not for the `COMEDI_CMD` ioctl and its handlers.
Both `do_cmd_ioctl()` and `do_cmdtest_ioctl()` call
`__comedi_get_user_chanlist()` to copy the channel list from user memory
into dynamically allocated kernel memory and check it for consistency.
That function currently returns 0 if the `user_chanlist` parameter
(pointing to the channel list in user memory) is NULL. That's fine for
`do_cmdtest_ioctl()`, but `do_cmd_ioctl()` incorrectly assumes the
kernel copy of the channel list has been set-up correctly.
Fix it by not allowing the `user_chanlist` parameter to be NULL in
`__comedi_get_user_chanlist()`, and only calling it from
`do_cmdtest_ioctl()` if the parameter is non-NULL.
Thanks to Bernd Porr for reporting the bug via an initial patch sent
privately.
Fixes: c6cd0eefb2 ("staging: comedi: comedi_fops: introduce __comedi_get_user_chanlist()")
Reported-by: Bernd Porr <mail@berndporr.me.uk>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Bernd Porr <mail@berndporr.me.uk>
Cc: <stable@vger.kernel.org> # 3.15.y 3.16.y 3.17.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These stock GCC versions miscompile the kernel by incorrectly optimising
the function epilogue code - by first increasing the stack pointer, and
then loading entries from below the stack. This means that an opportune
interrupt or exception will corrupt the current function's saved state,
which may result in the parent function seeing different register
values.
As this bug has been known to result in corrupted filesystems, and these
buggy compiler versions seem to be frequently used, we have little
option but to blacklist these compiler versions.
Distributions may have fixed PR58854, but as their compilers are totally
indistinguishable from the buggy versions, it is unfortunate that this
also results in those also being blacklisted. Given the filesystem
corruption potential of the original, this is the lesser evil. People
who want to build with their fixed compiler versions will need to adjust
the kernel source. (Distros need to think about the implications of
fixing such a compiler bug, and consider how to ensure that their fixed
compiler versions can be detected if they wish to avoid this.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Interpret NFTA_NAT_REG_ADDR_MAX if NFTA_NAT_REG_ADDR_MIN is present,
otherwise, skip it. Same thing with NFTA_NAT_REG_PROTO_MAX.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We have to validate that we at least get an NFTA_NAT_REG_ADDR_MIN or
NFTA_NFT_REG_PROTO_MIN attribute. Reject the configuration if none
of them are present.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We have to validate the real chain type to ensure that matches/targets
are not used out from their scope (eg. MASQUERADE in nat chain type).
The existing validation relies on the table name, but this is not
sufficient since userspace can fool us by using the appropriate table
name with a different chain type.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Drivers currently call spi_nor_match_id() and then spi_nor_scan().
This adds a dependency on struct spi_device_id which we want to
avoid. Make spi_nor_scan() do it for them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This simplifies the way we use spi_nor framework and will allow us to
drop spi_nor_match_id.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A future commit changes the way various vblank calls behave, which
causes drivers to break. Converting to use the drm_crtc_vblank_on/off
calls avoids this breakage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A refcounting leak was found of the original frame buffer attached to
the CRTC when using the page_flip ioctl, resulting in the frame buffer
never being freed.
This was not obvious initially, as if the page flip subsequently
re-attaches the original frame buffer, the refcounts will be balanced.
However, if the original frame buffer is freed, then it will be leaked.
Fix this by ensuring that we take a reference on the incoming fb, but
rely on the queued work to drop that ref count.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The shrinker uses gfp flags to indicate what kind of operation can the
driver wait for. If __GFP_IO flag is present, the driver can wait for
block I/O operations, if __GFP_FS flag is present, the driver can wait on
operations involving the filesystem.
dm-bufio tested for __GFP_IO. However, dm-bufio can run on a loop block
device that makes calls into the filesystem. If __GFP_IO is present and
__GFP_FS isn't, dm-bufio could still block on filesystem operations if it
runs on a loop block device.
The change from __GFP_IO to __GFP_FS supposedly fixes one observed (though
unreproducible) deadlock involving dm-bufio and loop device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
In rx mode, dma must be prepared before spi is enabled.
But in tx and tr mode, spi must be enabled first.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the minimum divisor in rk3x's spi controller is 2,
if spi_clk is less than 2 * sclk_out, we can't get the right divisor.
So we must set spi_clk again to match slave request.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sgtl5000 has two required supplies: VDDA and VDDIO and one optional supply:
VDDD, so document this properly.
Not passing VDDA and VDDIO prevents the driver to probe successfully.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch changes 32-bit time types to 64-bit in
drivers/power/ab8500_fg.c
timespec and time_t can only represent signed 32-bit
dates but the driver should represent dates that are
after January 2038. So used time64.h header file and
its proper types and functions.
Use time64_t type instead of __kernel_time_t for
time_stamps variable of ab8500_fg_avg_cap struct
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Set hook_mask to zero for non-base chains, otherwise people may hit
bogus errors from the xt_check_target() and xt_check_match() when
validating the uninitialized hook_mask.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It affects non-(V)HT rates and can lead to selecting an rts_cts rate
that is not a basic rate or way superior to the reference rate (ATM
rates[0] used for the 1st attempt of the protected frame data).
E.g, assuming drivers register growing (bitrate) sorted tables of
ieee80211_rate-s, having :
- rates[0].idx == d'2 and basic_rates == b'10100
will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise
- rates[0].idx == d'2 and basic_rates == b'10001
will select rts_cts idx b'10000
The first is not a basic rate and the second is > rates[0].
Also, wrt severity of the addressed misbehavior, ATM we only have one
rts_cts_rate_idx rather than one per rate table entry, so this idx might
still point to bitrates > rates[1..MAX_RATES].
Fixes: 5253ffb8c9 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates")
Cc: stable@vger.kernel.org
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the missing validation code to avoid the use of nat/masq from
non-nat chains. The validation assumes two possible configuration
scenarios:
1) Use of nat from base chain that is not of nat type. Reject this
configuration from the nft_*_init() path of the expression.
2) Use of nat from non-base chain. In this case, we have to wait until
the non-base chain is referenced by at least one base chain via
jump/goto. This is resolved from the nft_*_validate() path which is
called from nf_tables_check_loops().
The user gets an -EOPNOTSUPP in both cases.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
By using separate TX and RX bounce buffers, we avoid potential cache
flush and invalidation sequence issue that may be encountered when a
single bounce buffer is shared between TX and RX
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sh:sh2007_defconfig fails to build with the following error:
In file included from include/linux/regulator/machine.h:18:0,
from arch/sh/boards/board-sh2007.c:10:
include/linux/regulator/consumer.h: In function 'regulator_get_optional':
include/linux/regulator/consumer.h:271:2:
error: implicit declaration of function 'ERR_PTR'
include/linux/err.h: At top level:
include/linux/err.h:23:35: error: conflicting types for 'ERR_PTR'
include/linux/regulator/consumer.h:271:9:
note: previous implicit declaration of 'ERR_PTR' was here
Since consumer.h uses ERR_PTR, it should include err.h.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a potential struct stripe_c leak that would occur if the
chunk_size exceeded the maximum allowed by dm_set_target_max_io_len
(UINT_MAX). However, in practice there is no possibility of this
occuring given that chunk_size is of type uint32_t. But it is good to
fix this to future-proof in case dm_set_target_max_io_len's
implementation were to change.
Signed-off-by: Pavitra Kumar <pavitrak@nvidia.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The nl80211 channel switch count attribute
(NL80211_ATTR_CH_SWITCH_COUNT) is specified as u32, but the
specification uses u8 for the counter. To make sure strange things
don't happen without informing the user, sanity check the value and
return -EINVAL if it doesn't fit in u8.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct the kernel-doc, the parameter is called "blocked" not "state".
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chandef of the channel context a vif is using may be different
than the chandef of the vif itself. For instance, the bandwidth used
by the vif may be narrower than the one configured in the channel
context. To avoid confusion, return the vif's chandef in
ieee80211_cfg_get_channel() instead of the chandef of the channel
context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The of_node element must be initialized to enable discovery of node
children which takes place in the of_register_spi_devices() function.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Otherwise we get the following build warning:
(XTENSA_PLATFORM_XTFPGA) selects ETHOC which has unmet direct
dependencies (NETDEVICES && ETHERNET && HAS_IOMEM && HAS_DMA)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The default pgprot_noncached doesn't do anything. This leads to issues
when drivers rely on it to disable caching in userspace mappings.
Implement pgprot_noncached properly so that caching of userspace mappings
could be controlled.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
"raw" is the name of a channel property, but should not be part of the
channel name itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In older versions of the IIO framework it was possible to pass a
completely different set of channels to iio_buffer_register() as the one
that is assigned to the IIO device. Commit 959d2952d1 ("staging:iio: make
iio_sw_buffer_preenable much more general.") introduced a restriction that
requires that the set of channels that is passed to iio_buffer_register() is
a subset of the channels assigned to the IIO device as the IIO core will use
the list of channels that is assigned to the device to lookup a channel by
scan index in iio_compute_scan_bytes(). If it can not find the channel the
function will crash. This patch fixes the issue by making sure that the same
set of channels is assigned to the IIO device and passed to
iio_buffer_register().
Fixes the follow NULL pointer derefernce kernel crash:
Unable to handle kernel NULL pointer dereference at virtual address 00000016
pgd = d53d0000
[00000016] *pgd=1534e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 1626 Comm: bash Not tainted 3.15.0-19969-g2a180eb-dirty #9545
task: d6c124c0 ti: d539a000 task.ti: d539a000
PC is at iio_compute_scan_bytes+0x34/0xa8
LR is at iio_compute_scan_bytes+0x34/0xa8
pc : [<c03052e4>] lr : [<c03052e4>] psr: 60070013
sp : d539beb8 ip : 00000001 fp : 00000000
r10: 00000002 r9 : 00000000 r8 : 00000001
r7 : 00000000 r6 : d6dc8800 r5 : d7571000 r4 : 00000002
r3 : d7571000 r2 : 00000044 r1 : 00000001 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 18c5387d Table: 153d004a DAC: 00000015
Process bash (pid: 1626, stack limit = 0xd539a240)
Stack: (0xd539beb8 to 0xd539c000)
bea0: c02fc0e4 d7571000
bec0: d76c1640 d6dc8800 d757117c 00000000 d757112c c0305b04 d76c1690 d76c1640
bee0: d7571188 00000002 00000000 d7571000 d539a000 00000000 000dd1c8 c0305d54
bf00: d7571010 0160b868 00000002 c69d3900 d7573278 d7573308 c69d3900 c01ece90
bf20: 00000002 c0103fac c0103f6c d539bf88 00000002 c69d3b00 c69d3b0c c0103468
bf40: 00000000 00000000 d7694a00 00000002 000af408 d539bf88 c000dd84 c00b2f94
bf60: d7694a00 000af408 00000002 d7694a00 d7694a00 00000002 000af408 c000dd84
bf80: 00000000 c00b32d0 00000000 00000000 00000002 b6f1aa78 00000002 000af408
bfa0: 00000004 c000dc00 b6f1aa78 00000002 00000001 000af408 00000002 00000000
bfc0: b6f1aa78 00000002 000af408 00000004 be806a4c 000a6094 00000000 000dd1c8
bfe0: 00000000 be8069cc b6e8ab77 b6ec125c 40070010 00000001 22940489 154a5007
[<c03052e4>] (iio_compute_scan_bytes) from [<c0305b04>] (__iio_update_buffers+0x248/0x438)
[<c0305b04>] (__iio_update_buffers) from [<c0305d54>] (iio_buffer_store_enable+0x60/0x7c)
[<c0305d54>] (iio_buffer_store_enable) from [<c01ece90>] (dev_attr_store+0x18/0x24)
[<c01ece90>] (dev_attr_store) from [<c0103fac>] (sysfs_kf_write+0x40/0x4c)
[<c0103fac>] (sysfs_kf_write) from [<c0103468>] (kernfs_fop_write+0x110/0x154)
[<c0103468>] (kernfs_fop_write) from [<c00b2f94>] (vfs_write+0xd0/0x160)
[<c00b2f94>] (vfs_write) from [<c00b32d0>] (SyS_write+0x40/0x78)
[<c00b32d0>] (SyS_write) from [<c000dc00>] (ret_fast_syscall+0x0/0x30)
Code: ea00000e e1a01008 e1a00005 ebfff6fc (e5d0a016)
Fixes: 959d2952d1 ("staging:iio: make iio_sw_buffer_preenable much more general.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit: e676253b19 [3/21] serial/8250: Add
support for RS485 IOCTLs, adds support for RS485 ioctls for 825_core on
all the archs. Unfortunaltely the definition of TIOCSRS485 and
TIOCGRS485 was missing on the ioctls.h file
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
2014-09-09 23:48:57 -07:00
1250 changed files with 11905 additions and 8214 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
