Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 6.16-rc4. It resolves a build
error in the rtl8723bs driver for some versions of clang on arm64 when
checking the frame size with -Wframe-larger-than.
It has been in linux-next for a while now with no reported issues"
* tag 'staging-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: Avoid memset() in aes_cipher() and aes_decipher()
Pull tty/serial driver fixes from Greg KH:
"Here are five small serial and tty and vt fixes for 6.16-rc4. Included
in here are:
- kerneldoc fixes for recent vt changes
- imx serial driver fix
- of_node sysfs fix for a regression
- vt missing notification fix
- 8250 dt bindings fix
All of these have been in linux-next for a while with no reported issues"
* tag 'tty-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250: Make clocks and clock-frequency exclusive
serial: imx: Restore original RXTL for console to fix data loss
serial: core: restore of_node information in sysfs
vt: fix kernel-doc warnings in ucs_get_fallback()
vt: add missing notification when switching back to text mode
Pull EDAC fix from Borislav Petkov:
- Consider secondary address mask registers in amd64_edac in order to
get the correct total memory size of the system
* tag 'edac_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Fix size calculation for Non-Power-of-Two DIMMs
Pull x86 fixes from Borislav Petkov:
- Make sure DR6 and DR7 are initialized to their architectural values
and not accidentally cleared, leading to misconfigurations
* tag 'x86_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/traps: Initialize DR7 by writing its architectural reset value
x86/traps: Initialize DR6 by writing its architectural reset value
Pull perf fix from Borislav Petkov:
- Make sure an AUX perf event is really disabled when it overruns
* tag 'perf_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Fix pending disable flow when the AUX ring buffer overruns
Pull locking fix from Borislav Petkov:
- Make sure the new futex phash is not copied during fork in order to
avoid a double-free
* tag 'locking_urgent_for_v6.16_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Initialize futex_phash_new during fork().
Pull i2c fixes from Wolfram Sang:
- imx: fix SMBus protocol compliance during block read
- omap: fix error handling path in probe
- robotfuzz, tiny-usb: prevent zero-length reads
- x86, designware, amdisp: fix build error when modules are disabled
(agreed to go in via i2c)
- scx200_acb: fix build error because of missing HAS_IOPORT
* tag 'i2c-for-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: scx200_acb: depends on HAS_IOPORT
i2c: omap: Fix an error handling path in omap_i2c_probe()
platform/x86: Use i2c adapter name to fix build errors
i2c: amd-isp: Initialize unique adapter name
i2c: designware: Initialize adapter name only when not set
i2c: tiny-usb: disable zero-length read messages
i2c: robotfuzz-osif: disable zero-length read messages
i2c: imx: fix emulated smbus block read
Pull tracing fix from Steven Rostedt:
- Fix possible UAF on error path in filter_free_subsystem_filters()
When freeing a subsystem filter, the filter for the subsystem is
passed in to be freed and all the events within the subsystem will
have their filter freed too. In order to free without waiting for RCU
synchronization, list items are allocated to hold what is going to be
freed to free it via a call_rcu(). If the allocation of these items
fails, it will call the synchronization directly and free after that
(causing a bit of delay for the user).
The subsystem filter is first added to this list and then the filters
for all the events under the subsystem. The bug is if one of the
allocations of the list items for the event filters fail to allocate,
it jumps to the "free_now" label which will free the subsystem
filter, then all the items on the allocated list, and then the event
filters that were not added to the list yet. But because the
subsystem filter was added first, it gets freed twice.
The solution is to add the subsystem filter after the events, and
then if any of the allocations fail it will not try to free any of
them twice
* tag 'trace-v6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix filter logic error
Pull LoongArch fixes from Huacai Chen:
- replace __ASSEMBLY__ with __ASSEMBLER__ in headers like others
- fix build warnings about export.h
- reserve the EFI memory map region for kdump
- handle __init vs inline mismatches
- fix some KVM bugs
* tag 'loongarch-fixes-6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Disable updating of "num_cpu" and "feature"
LoongArch: KVM: Check validity of "num_cpu" from user space
LoongArch: KVM: Check interrupt route from physical CPU
LoongArch: KVM: Fix interrupt route update with EIOINTC
LoongArch: KVM: Add address alignment check for IOCSR emulation
LoongArch: KVM: Avoid overflow with array index
LoongArch: Handle KCOV __init vs inline mismatches
LoongArch: Reserve the EFI memory map region
LoongArch: Fix build warnings about export.h
LoongArch: Replace __ASSEMBLY__ with __ASSEMBLER__ in headers
Pull smb client fixes from Steve French:
- Multichannel reconnect lock ordering deadlock fix
- Fix for regression in handling native Windows symlinks
- Three smbdirect fixes:
- oops in RDMA response processing
- smbdirect memcpy issue
- fix smbdirect regression with large writes (smbdirect test cases
now all passing)
- Fix for "FAILED_TO_PARSE" warning in trace-cmd report output
* tag 'v6.16-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix reading into an ITER_FOLIOQ from the smbdirect code
cifs: Fix the smbd_response slab to allow usercopy
smb: client: fix potential deadlock when reconnecting channels
smb: client: remove \t from TP_printk statements
smb: client: let smbd_post_send_iter() respect the peers max_send_size and transmit all data
smb: client: fix regression with native SMB symlinks
Pull misc fixes from Andrew Morton:
"16 hotfixes.
6 are cc:stable and the remainder address post-6.15 issues or aren't
considered necessary for -stable kernels. 5 are for MM"
* tag 'mm-hotfixes-stable-2025-06-27-16-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS: add Lorenzo as THP co-maintainer
mailmap: update Duje Mihanović's email address
selftests/mm: fix validate_addr() helper
crashdump: add CONFIG_KEYS dependency
mailmap: correct name for a historical account of Zijun Hu
mailmap: add entries for Zijun Hu
fuse: fix runtime warning on truncate_folio_batch_exceptionals()
scripts/gdb: fix dentry_name() lookup
mm/damon/sysfs-schemes: free old damon_sysfs_scheme_filter->memcg_path on write
mm/alloc_tag: fix the kmemleak false positive issue in the allocation of the percpu variable tag->counters
lib/group_cpus: fix NULL pointer dereference from group_cpus_evenly()
mm/hugetlb: remove unnecessary holding of hugetlb_lock
MAINTAINERS: add missing files to mm page alloc section
MAINTAINERS: add tree entry to mm init block
mm: add OOM killer maintainer structure
fs/proc/task_mmu: fix PAGE_IS_PFNZERO detection for the huge zero folio
Pull RISC-V Fixes for 5.16-rc4
- .rodata is no longer linkd into PT_DYNAMIC.
It was not supposed to be there in the first place and resulted in
invalid (but unused) entries. This manifests as at least warnings in
llvm-readelf
- A fix for runtime constants with all-0 upper 32-bits. This should
only manifest on MMU=n kernels
- A fix for context save/restore on systems using the T-Head vector
extensions
- A fix for a conflicting "+r"/"r" register constraint in the VDSO
getrandom syscall wrapper, which is undefined behavior in clang
- A fix for a missing register clobber in the RVV raid6 implementation.
This manifests as a NULL pointer reference on some compilers, but
could trigger in other ways
- Misaligned accesses from userspace at faulting addresses are now
handled correctly
- A fix for an incorrect optimization that allowed access_ok() to mark
invalid addresses as accessible, which can result in userspace
triggering BUG()s
- A few fixes for build warnings, and an update to Drew's email address
* tag 'riscv-for-linus-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export boot_cpu_hartid
Revert "riscv: Define TASK_SIZE_MAX for __access_ok()"
riscv: Fix sparse warning in vendor_extensions/sifive.c
Revert "riscv: misaligned: fix sleeping function called during misaligned access handling"
MAINTAINERS: Update Drew Fustini's email address
RISC-V: uaccess: Wrap the get_user_8 uaccess macro
raid6: riscv: Fix NULL pointer dereference caused by a missing clobber
RISC-V: vDSO: Correct inline assembly constraints in the getrandom syscall wrapper
riscv: vector: Fix context save/restore with xtheadvector
riscv: fix runtime constant support for nommu kernels
riscv: vdso: Exclude .rodata from the PT_DYNAMIC segment
Pull PCI fix from Bjorn Helgaas:
- Fix a PTM debugfs build error with CONFIG_DEBUG_FS=n &&
CONFIG_PCIE_PTM=y (Manivannan Sadhasivam)
* tag 'pci-v6.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/PTM: Build debugfs code only if CONFIG_DEBUG_FS is enabled
Pull drm fixes from Dave Airlie:
"Regular weekly drm updates, nothing out of the ordinary, amdgpu, xe,
i915 and a few misc bits. Seems about right for this time in the
release cycle.
core:
- fix drm_writeback_connector_cleanup function signature
- use correct HDMI audio bridge in drm_connector_hdmi_audio_init
bridge:
- SN65DSI86: fix HPD
amdgpu:
- Cleaner shader support for additional GFX9 GPUs
- MES firmware compatibility fixes
- Discovery error reporting fixes
- SDMA6/7 userq fixes
- Backlight fix
- EDID sanity check
i915:
- Fix for SNPS PHY HDMI for 1080p@120Hz
- Correct DP AUX DPCD probe address
- Followup build fix for GCOV and AutoFDO enabled config
xe:
- Missing error check
- Fix xe_hwmon_power_max_write
- Move flushes
- Explicitly exit CT safe mode on unwind
- Process deferred GGTT node removals on device unwind"
* tag 'drm-fixes-2025-06-28' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe: Process deferred GGTT node removals on device unwind
drm/xe/guc: Explicitly exit CT safe mode on unwind
drm/xe: move DPT l2 flush to a more sensible place
drm/xe: Move DSB l2 flush to a more sensible place
drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type
drm/i915: fix build error some more
drm/xe/hwmon: Fix xe_hwmon_power_max_write
drm/xe/display: Add check for alloc_ordered_workqueue()
drm/amd/display: Add sanity checks for drm_edid_raw()
drm/amd/display: Fix AMDGPU_MAX_BL_LEVEL value
drm/amdgpu/sdma7: add ucode version checks for userq support
drm/amdgpu/sdma6: add ucode version checks for userq support
drm/amd: Adjust output for discovery error handling
drm/amdgpu/mes: add compatibility checks for set_hw_resource_1
drm/amdgpu/gfx9: Add Cleaner Shader Support for GFX9.x GPUs
drm/bridge-connector: Fix bridge in drm_connector_hdmi_audio_init()
drm/dp: Change AUX DPCD probe address from DPCD_REV to LANE0_1_STATUS
drm/i915/snps_hdmi_pll: Fix 64-bit divisor truncation by using div64_u64
drm: writeback: Fix drm_writeback_connector_cleanup signature
Pull Compute Express Link (CXL) fixes from Dave Jiang:
"These fixes address a few issues in the CXL subsystem, including
dealing with some bugs in the CXL EDAC and RAS drivers:
- Fix return value of cxlctl_validate_set_features()
- Fix min_scrub_cycle of a region miscaculation and add additional
documentation
- Fix potential memory leak issues for CXL EDAC
- Fix CPER handler device confusion for CXL RAS
- Fix using wrong repair type to check DRAM event record"
* tag 'cxl-fixes-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/edac: Fix using wrong repair type to check dram event record
cxl/ras: Fix CPER handler device confusion
cxl/edac: Fix potential memory leak issues
cxl/Documentation: Add more description about min/max scrub cycle
cxl/edac: Fix the min_scrub_cycle of a region miscalculation
cxl: fix return value in cxlctl_validate_set_features()
Pull crypto library fix from Eric Biggers:
"Fix a regression where the purgatory code sometimes fails to build"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: sha256: Mark sha256_choose_blocks as __always_inline
Pull ACPI fix from Rafael Wysocki:
"Revert a commit that attempted to fix a memory leak in an error code
path and introduced a different issue (Zhe Qiao)"
* tag 'acpi-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PCI/ACPI: Fix allocated memory release on error in pci_acpi_scan_root()"
Pull block fixes from Jens Axboe:
- Fixes for ublk:
- fix C++ narrowing warnings in the uapi header
- update/improve UBLK_F_SUPPORT_ZERO_COPY comment in uapi header
- fix for the ublk ->queue_rqs() implementation, limiting a batch
to just the specific task AND ring
- ublk_get_data() error handling fix
- sanity check more arguments in ublk_ctrl_add_dev()
- selftest addition
- NVMe pull request via Christoph:
- reset delayed remove_work after reconnect
- fix atomic write size validation
- Fix for a warning introduced in bdev_count_inflight_rw() in this
merge window
* tag 'block-6.16-20250626' of git://git.kernel.dk/linux:
block: fix false warning in bdev_count_inflight_rw()
ublk: sanity check add_dev input for underflow
nvme: fix atomic write size validation
nvme: refactor the atomic write unit detection
nvme: reset delayed remove_work after reconnect
ublk: setup ublk_io correctly in case of ublk_get_data() failure
ublk: update UBLK_F_SUPPORT_ZERO_COPY comment in UAPI header
ublk: fix narrowing warnings in UAPI header
selftests: ublk: don't take same backing file for more than one ublk devices
ublk: build batch from IOs in same io_ring_ctx and io task
Pull io_uring fixes from Jens Axboe:
- Two tweaks for a recent fix: fixing a memory leak if multiple iovecs
were initially mapped but only the first was used and hence turned
into a UBUF rathan than an IOVEC iterator, and catching a case where
a retry would be done even if the previous segment wasn't full
- Small series fixing an issue making the vm unhappy if debugging is
turned on, hitting a VM_BUG_ON_PAGE()
- Fix a resource leak in io_import_dmabuf() in the error handling case,
which is a regression in this merge window
- Mark fallocate as needing to be write serialized, as is already done
for truncate and buffered writes
* tag 'io_uring-6.16-20250626' of git://git.kernel.dk/linux:
io_uring/kbuf: flag partial buffer mappings
io_uring/net: mark iov as dynamically allocated even for single segments
io_uring: fix resource leak in io_import_dmabuf()
io_uring: don't assume uaddr alignment in io_vec_fill_bvec
io_uring/rsrc: don't rely on user vaddr alignment
io_uring/rsrc: fix folio unpinning
io_uring: make fallocate be hashed work
Pull ata fix from Niklas Cassel:
- Use the correct DMI identifier for ASUSPRO-D840SA LPM quirk such that
the quirk actually gets applied (me)
* tag 'ata-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Use correct DMI identifier for ASUSPRO-D840SA LPM quirk
Pull s390 fixes from Alexander Gordeev:
- Fix incorrectly dropped dereferencing of the stack nth entry
introduced with a previous KASAN false positive fix
- Use a proper memdup_array_user() helper to prevent overflow in a
protected key size calculation
* tag 's390-6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ptrace: Fix pointer dereferencing in regs_get_kernel_stack_nth()
s390/pkey: Prevent overflow in size calculation for memdup_user()
Pull sound fixes from Takashi Iwai:
"A collection of small fixes again:
- A regression fix for hibernation bug in ASoC SoundWire
- Fixes for the new Qualcomm USB offload stuff
- A potential OOB access fix in USB-audio
- A potential memleadk fix in ASoC Intel
- Quirks for HD-audio and ASoC AMD ACP"
* tag 'sound-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Fix built-in mic on ASUS VivoBook X507UAR
ALSA: usb: qcom: fix NULL pointer dereference in qmi_stop_session
ASoC: SOF: Intel: hda: Use devm_kstrdup() to avoid memleak.
ASoC: rt721-sdca: fix boost gain calculation error
ALSA: qc_audio_offload: Fix missing error code in prepare_qmi_response()
ALSA: hda/realtek: Add mic-mute LED setup for ASUS UM5606
ALSA: usb-audio: Fix out-of-bounds read in snd_usb_get_audioformat_uac3()
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 6 G1a
ASoC: amd: ps: fix for soundwire failures during hibernation exit sequence
ASoC: amd: yc: Add DMI quirk for Lenovo IdeaPad Slim 5 15
ASoC: amd: yc: add quirk for Acer Nitro ANV15-41 internal mic
ASoC: qcom: sm8250: Fix possibly undefined reference
ALSA: hda/realtek - Enable mute LED on HP Pavilion Laptop 15-eg100
ALSA: hda/realtek: Add quirks for some Clevo laptops
It already depends on X86_32, but that's also set for ARCH=um.
Recent changes made UML no longer have IO port access since
it's not needed, but this driver uses it. Build it only for
HAS_IOPORT. This is pretty much the same as depending on X86,
but on the off-chance that HAS_IOPORT will ever be optional
on x86 HAS_IOPORT is the real prerequisite.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Property "num_cpu" and "feature" are read-only once eiointc is created,
which are set with KVM_DEV_LOONGARCH_EXTIOI_GRP_CTRL attr group before
device creation.
Attr group KVM_DEV_LOONGARCH_EXTIOI_GRP_SW_STATUS is to update register
and software state for migration and reset usage, property "num_cpu" and
"feature" can not be update again if it is created already.
Here discard write operation with property "num_cpu" and "feature" in
attr group KVM_DEV_LOONGARCH_EXTIOI_GRP_CTRL.
Cc: stable@vger.kernel.org
Fixes: 1ad7efa552 ("LoongArch: KVM: Add EIOINTC user mode read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The maximum supported cpu number is EIOINTC_ROUTE_MAX_VCPUS about
irqchip EIOINTC, here add validation about cpu number to avoid array
pointer overflow.
Cc: stable@vger.kernel.org
Fixes: 1ad7efa552 ("LoongArch: KVM: Add EIOINTC user mode read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
With EIOINTC interrupt controller, physical CPU ID is set for irq route.
However the function kvm_get_vcpu() is used to get destination vCPU when
delivering irq. With API kvm_get_vcpu(), the logical CPU ID is used.
With API kvm_get_vcpu_by_cpuid(), vCPU ID can be searched from physical
CPU ID.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc0 ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
With function eiointc_update_sw_coremap(), there is forced assignment
like val = *(u64 *)pvalue. Parameter pvalue may be pointer to char type
or others, there is problem with forced assignment with u64 type.
Here the detailed value is passed rather address pointer.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc0 ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
IOCSR instruction supports 1/2/4/8 bytes access, the address should be
naturally aligned with its access size. Here address alignment check is
added in the EIOINTC kernel emulation.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc0 ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Pull crypto fix from Herbert Xu:
"This fixes a regression where wp512 can no longer be used with hmac"
* tag 'v6.16-p6' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: wp512 - Use API partial block handling
Pull bcachefs fixes from Kent Overstreet:
- Lots of small check/repair fixes, primarily in subvol loop and
directory structure loop (when involving snapshots).
- Fix a few 6.16 regressions: rare UAF in the foreground allocator path
when taking a transaction restart from the transaction bump
allocator, and some small fallout from the change to log the error
being corrected in the journal when repairing errors, also some
fallout from the btree node read error logging improvements.
(Alan, Bharadwaj)
- New option: journal_rewind
This lets the entire filesystem be reset to an earlier point in time.
Note that this is only a disaster recovery tool, and right now there
are major caveats to using it (discards should be disabled, in
particular), but it successfully restored the filesystem of one of
the users who was bit by the subvolume deletion bug and didn't have
backups. I'll likely be making some changes to the discard path in
the future to make this a reliable recovery tool.
- Some new btree iterator tracepoints, for tracking down some
livelock-ish behaviour we've been seeing in the main data write path.
* tag 'bcachefs-2025-06-26' of git://evilpiepirate.org/bcachefs: (51 commits)
bcachefs: Plumb correct ip to trans_relock_fail tracepoint
bcachefs: Ensure we rewind to run recovery passes
bcachefs: Ensure btree node scan runs before checking for scanned nodes
bcachefs: btree_root_unreadable_and_scan_found_nothing should not be autofix
bcachefs: fix bch2_journal_keys_peek_prev_min() underflow
bcachefs: Use wait_on_allocator() when allocating journal
bcachefs: Check for bad write buffer key when moving from journal
bcachefs: Don't unlock the trans if ret doesn't match BCH_ERR_operation_blocked
bcachefs: Fix range in bch2_lookup_indirect_extent() error path
bcachefs: fix spurious error_throw
bcachefs: Add missing bch2_err_class() to fileattr_set()
bcachefs: Add missing key type checks to check_snapshot_exists()
bcachefs: Don't log fsck err in the journal if doing repair elsewhere
bcachefs: Fix *__bch2_trans_subbuf_alloc() error path
bcachefs: Fix missing newlines before ero
bcachefs: fix spurious error in read_btree_roots()
bcachefs: fsck: Fix oops in key_visible_in_snapshot()
bcachefs: fsck: fix unhandled restart in topology repair
bcachefs: fsck: Fix check_directory_structure when no check_dirents
bcachefs: Fix restart handling in btree_node_scrub_work()
...
Pull HID fixes from Jiri Kosina:
- fix for stalls during suspend/resume cycles with hid-nintendo (Daniel
J. Ogorchock)
- memory leak and reference count fixes in hid-wacom and in-appletb-kdb
(Qasim Ijaz)
- race condition (leading to kernel crash) fix during device removal in
hid-wacom (Thomas Zeitlhofer)
- fix for missed interrupt in intel-thc-hid (Intel-thc-hid:)
- support for a bunch of new device IDs
* tag 'hid-for-linus-2025062701' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: lenovo: Add support for ThinkPad X1 Tablet Thin Keyboard Gen2
HID: appletb-kbd: fix "appletb_backlight" backlight device reference counting
HID: wacom: fix crash in wacom_aes_battery_handler()
HID: intel-ish-hid: ipc: Add Wildcat Lake PCI device ID
hid: intel-ish-hid: Use PCI_DEVICE_DATA() macro for ISH device table
HID: lenovo: Restrict F7/9/11 mode to compact keyboards only
HID: Add IGNORE quirk for SMARTLINKTECHNOLOGY
HID: input: lower message severity of 'No inputs registered, leaving' to debug
HID: quirks: Add quirk for 2 Chicony Electronics HP 5MP Cameras
HID: Intel-thc-hid: Intel-quicki2c: Enhance QuickI2C reset flow
HID: nintendo: avoid bluetooth suspend/resume stalls
HID: wacom: fix kobject reference count leak
HID: wacom: fix memory leak on sysfs attribute creation failure
HID: wacom: fix memory leak on kobject creation failure
Pull devicetree fixes from Rob Herring:
- Convert altr,uart-1.0 and altr,juart-1.0 to DT schema. These were
applied for nios2, but never sent upstream.
- Fix extra '/' in fsl,ls1028a-reset '$id' path
- Fix warnings in ti,sn65dsi83 schema due to unnecessary $ref.
* tag 'devicetree-fixes-for-6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: serial: Convert altr,uart-1.0 to DT schema
dt-bindings: serial: Convert altr,juart-1.0 to DT schema
dt-bindings: soc: fsl,ls1028a-reset: Drop extra "/" in $id
dt-bindings: drm/bridge: ti-sn65dsi83: drop $ref to fix lvds-vod* warnings
A previous commit aborted mapping more for a non-incremental ring for
bundle peeking, but depending on where in the process this peeking
happened, it would not necessarily prevent a retry by the user. That can
create gaps in the received/read data.
Add struct buf_sel_arg->partial_map, which can pass this information
back. The networking side can then map that to internal state and use it
to gate retry as well.
Since this necessitates a new flag, change io_sr_msg->retry to a
retry_flags member, and store both the retry and partial map condition
in there.
Cc: stable@vger.kernel.org
Fixes: 26ec15e4b0 ("io_uring/kbuf: don't truncate end buffer for multiple buffer peeks")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When performing a file read from RDMA, smbd_recv() prints an "Invalid msg
type 4" error and fails the I/O. This is due to the switch-statement there
not handling the ITER_FOLIOQ handed down from netfslib.
Fix this by collapsing smbd_recv_buf() and smbd_recv_page() into
smbd_recv() and just using copy_to_iter() instead of memcpy(). This
future-proofs the function too, in case more ITER_* types are added.
Fixes: ee4cdf7ba8 ("netfs: Speed up buffered reading")
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Talpey <tom@talpey.com>
cc: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
The handling of received data in the smbdirect client code involves using
copy_to_iter() to copy data from the smbd_reponse struct's packet trailer
to a folioq buffer provided by netfslib that encapsulates a chunk of
pagecache.
If, however, CONFIG_HARDENED_USERCOPY=y, this will result in the checks
then performed in copy_to_iter() oopsing with something like the following:
CIFS: Attempting to mount //172.31.9.1/test
CIFS: VFS: RDMA transport established
usercopy: Kernel memory exposure attempt detected from SLUB object 'smbd_response_0000000091e24ea1' (offset 81, size 63)!
------------[ cut here ]------------
kernel BUG at mm/usercopy.c:102!
...
RIP: 0010:usercopy_abort+0x6c/0x80
...
Call Trace:
<TASK>
__check_heap_object+0xe3/0x120
__check_object_size+0x4dc/0x6d0
smbd_recv+0x77f/0xfe0 [cifs]
cifs_readv_from_socket+0x276/0x8f0 [cifs]
cifs_read_from_socket+0xcd/0x120 [cifs]
cifs_demultiplex_thread+0x7e9/0x2d50 [cifs]
kthread+0x396/0x830
ret_from_fork+0x2b8/0x3b0
ret_from_fork_asm+0x1a/0x30
The problem is that the smbd_response slab's packet field isn't marked as
being permitted for usercopy.
Fix this by passing parameters to kmem_slab_create() to indicate that
copy_to_iter() is permitted from the packet region of the smbd_response
slab objects, less the header space.
Fixes: ee4cdf7ba8 ("netfs: Speed up buffered reading")
Reported-by: Stefan Metzmacher <metze@samba.org>
Link: https://lore.kernel.org/r/acb7f612-df26-4e2a-a35d-7cd040f513e1@samba.org/
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Tested-by: Stefan Metzmacher <metze@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Fix cifs_signal_cifsd_for_reconnect() to take the correct lock order
and prevent the following deadlock from happening
======================================================
WARNING: possible circular locking dependency detected
6.16.0-rc3-build2+ #1301 Tainted: G S W
------------------------------------------------------
cifsd/6055 is trying to acquire lock:
ffff88810ad56038 (&tcp_ses->srv_lock){+.+.}-{3:3}, at: cifs_signal_cifsd_for_reconnect+0x134/0x200
but task is already holding lock:
ffff888119c64330 (&ret_buf->chan_lock){+.+.}-{3:3}, at: cifs_signal_cifsd_for_reconnect+0xcf/0x200
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&ret_buf->chan_lock){+.+.}-{3:3}:
validate_chain+0x1cf/0x270
__lock_acquire+0x60e/0x780
lock_acquire.part.0+0xb4/0x1f0
_raw_spin_lock+0x2f/0x40
cifs_setup_session+0x81/0x4b0
cifs_get_smb_ses+0x771/0x900
cifs_mount_get_session+0x7e/0x170
cifs_mount+0x92/0x2d0
cifs_smb3_do_mount+0x161/0x460
smb3_get_tree+0x55/0x90
vfs_get_tree+0x46/0x180
do_new_mount+0x1b0/0x2e0
path_mount+0x6ee/0x740
do_mount+0x98/0xe0
__do_sys_mount+0x148/0x180
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #1 (&ret_buf->ses_lock){+.+.}-{3:3}:
validate_chain+0x1cf/0x270
__lock_acquire+0x60e/0x780
lock_acquire.part.0+0xb4/0x1f0
_raw_spin_lock+0x2f/0x40
cifs_match_super+0x101/0x320
sget+0xab/0x270
cifs_smb3_do_mount+0x1e0/0x460
smb3_get_tree+0x55/0x90
vfs_get_tree+0x46/0x180
do_new_mount+0x1b0/0x2e0
path_mount+0x6ee/0x740
do_mount+0x98/0xe0
__do_sys_mount+0x148/0x180
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #0 (&tcp_ses->srv_lock){+.+.}-{3:3}:
check_noncircular+0x95/0xc0
check_prev_add+0x115/0x2f0
validate_chain+0x1cf/0x270
__lock_acquire+0x60e/0x780
lock_acquire.part.0+0xb4/0x1f0
_raw_spin_lock+0x2f/0x40
cifs_signal_cifsd_for_reconnect+0x134/0x200
__cifs_reconnect+0x8f/0x500
cifs_handle_standard+0x112/0x280
cifs_demultiplex_thread+0x64d/0xbc0
kthread+0x2f7/0x310
ret_from_fork+0x2a/0x230
ret_from_fork_asm+0x1a/0x30
other info that might help us debug this:
Chain exists of:
&tcp_ses->srv_lock --> &ret_buf->ses_lock --> &ret_buf->chan_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ret_buf->chan_lock);
lock(&ret_buf->ses_lock);
lock(&ret_buf->chan_lock);
lock(&tcp_ses->srv_lock);
*** DEADLOCK ***
3 locks held by cifsd/6055:
#0: ffffffff857de398 (&cifs_tcp_ses_lock){+.+.}-{3:3}, at: cifs_signal_cifsd_for_reconnect+0x7b/0x200
#1: ffff888119c64060 (&ret_buf->ses_lock){+.+.}-{3:3}, at: cifs_signal_cifsd_for_reconnect+0x9c/0x200
#2: ffff888119c64330 (&ret_buf->chan_lock){+.+.}-{3:3}, at: cifs_signal_cifsd_for_reconnect+0xcf/0x200
Cc: linux-cifs@vger.kernel.org
Reported-by: David Howells <dhowells@redhat.com>
Fixes: d7d7a66aac ("cifs: avoid use of global locks for high contention data")
Reviewed-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
During driver probe we might be briefly using CT safe mode, which
is based on a delayed work, but usually we are able to stop this
once we have IRQ fully operational. However, if we abort the probe
quite early then during unwind we might try to destroy the workqueue
while there is still a pending delayed work that attempts to restart
itself which triggers a WARN.
This was recently observed during unsuccessful VF initialization:
[ ] xe 0000:00:02.1: probe with driver xe failed with error -62
[ ] ------------[ cut here ]------------
[ ] workqueue: cannot queue safe_mode_worker_func [xe] on wq xe-g2h-wq
[ ] WARNING: CPU: 9 PID: 0 at kernel/workqueue.c:2257 __queue_work+0x287/0x710
[ ] RIP: 0010:__queue_work+0x287/0x710
[ ] Call Trace:
[ ] delayed_work_timer_fn+0x19/0x30
[ ] call_timer_fn+0xa1/0x2a0
Exit the CT safe mode on unwind to avoid that warning.
Fixes: 09b286950f ("drm/xe/guc: Allow CTB G2H processing without G2H IRQ")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250612220937.857-3-michal.wajdeczko@intel.com
(cherry picked from commit 2ddbb73ec2)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
The variable index is modified and reused as array index when modify
register EIOINTC_ENABLE. There will be array index overflow problem.
Cc: stable@vger.kernel.org
Fixes: 3956a52bc0 ("LoongArch: KVM: Add EIOINTC read and write functions")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When the KCOV is enabled all functions get instrumented, unless
the __no_sanitize_coverage attribute is used. To prepare for
__no_sanitize_coverage being applied to __init functions, we have to
handle differences in how GCC's inline optimizations get resolved.
For LoongArch this exposed several places where __init annotations
were missing but ended up being "accidentally correct". So fix these
cases.
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The EFI memory map at 'boot_memmap' is crucial for kdump to understand
the primary kernel's memory layout. This memory region, typically part
of EFI Boot Services (BS) data, can be overwritten after ExitBootServices
if not explicitly preserved by the kernel.
This commit addresses this by:
1. Calling memblock_reserve() to reserve the entire physical region
occupied by the EFI memory map (header + descriptors). This prevents
the primary kernel from reallocating and corrupting this area.
2. Setting the EFI_PRESERVE_BS_REGIONS flag in efi.flags. This indicates
that efforts have been made to preserve critical BS code/data regions
which can be useful for other kernel subsystems or debugging.
These changes ensure the original EFI memory map data remains intact,
improving kdump reliability and potentially aiding other EFI-related
functionalities that might rely on preserved BS code/data.
Signed-off-by: Ming Wang <wangming01@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
After commit a934a57a42 ("scripts/misc-check: check missing #include
<linux/export.h> when W=1") and 7d95680d64 ("scripts/misc-check:
check unnecessary #include <linux/export.h> when W=1"), we get some build
warnings with W=1:
arch/loongarch/kernel/acpi.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/alternative.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/kfpu.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/traps.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/unwind_guess.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/unwind_orc.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/unwind_prologue.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/lib/crc32-loongarch.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/lib/csum.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing
arch/loongarch/kernel/elf.c: warning: EXPORT_SYMBOL() is not used, but #include <linux/export.h> is present
arch/loongarch/kernel/paravirt.c: warning: EXPORT_SYMBOL() is not used, but #include <linux/export.h> is present
arch/loongarch/pci/pci.c: warning: EXPORT_SYMBOL() is not used, but #include <linux/export.h> is present
So fix these build warnings for LoongArch.
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembler code, __ASSEMBLY__ is a macro
that only gets defined by the Makefiles in the kernel. This is bad
since macros starting with two underscores are names that are reserved
by the C language. It can also be very confusing for the developers
when switching between userspace and kernelspace coding, or when
dealing with uapi headers that rather should use __ASSEMBLER__ instead.
So let's now standardize on the __ASSEMBLER__ macro that is provided
by the compilers.
This is almost a completely mechanical patch (done with a simple
"sed -i" statement), with one comment tweaked manually in the
arch/loongarch/include/asm/cpu.h file (it was missing the trailing
underscores).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Don't mix the namespace and controller values, and validate the
per-controller limit when probing the controller. This avoid spurious
failures for controllers with namespaces that have different namespaces
with different logical block sizes, or report the per-namespace values
only for some namespaces.
It also fixes a missing queue_limits_cancel_update in an error path by
removing that error path.
Fixes: 8695f060a0 ("nvme: all namespaces in a subsystem must adhere to a common atomic write size")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Move all the code out of nvme_update_disk_info into the helper, and
rename the helper to have a somewhat less clumsy name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
The remove_work will proceed with permanently disconnecting on the
initial final path failure if the head shows no paths after the delay.
If a new path connects while the remove_work is pending, and if that new
path happens to disconnect before that remove_work executes, the delayed
removal should reset based on the most recent path disconnect time, but
queue_delayed_work() won't do anything if the work is already pending.
Attempt to cancel the delayed work when a new path connects, and use
mod_delayed_work() in case the remove_work remains pending anyway.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If an AUX event overruns, the event core layer intends to disable the
event by setting the 'pending_disable' flag. Unfortunately, the event
is not actually disabled afterwards.
In commit:
ca6c21327c ("perf: Fix missing SIGTRAPs")
the 'pending_disable' flag was changed to a boolean. However, the
AUX event code was not updated accordingly. The flag ends up holding a
CPU number. If this number is zero, the flag is taken as false and the
IRQ work is never triggered.
Later, with commit:
2b84def990 ("perf: Split __perf_pending_irq() out of perf_pending_irq()")
a new IRQ work 'pending_disable_irq' was introduced to handle event
disabling. The AUX event path was not updated to kick off the work queue.
To fix this bug, when an AUX ring buffer overrun is detected, call
perf_event_disable_inatomic() to initiate the pending disable flow.
Also update the outdated comment for setting the flag, to reflect the
boolean values (0 or 1).
Fixes: 2b84def990 ("perf: Split __perf_pending_irq() out of perf_pending_irq()")
Fixes: ca6c21327c ("perf: Fix missing SIGTRAPs")
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Liang Kan <kan.liang@linux.intel.com>
Cc: Marco Elver <elver@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-perf-users@vger.kernel.org
Link: https://lore.kernel.org/r/20250625170737.2918295-1-leo.yan@arm.com
ASoC: Fixes for v6.16
A small collection of fixes, the main one being a fix for resume from
hibernation on AMD systems, plus a few new quirk entries for AMD
systems.
Pull bpf fixes from Alexei Starovoitov:
- Fix use-after-free in libbpf when map is resized (Adin Scannell)
- Fix verifier assumptions about 2nd argument of bpf_sysctl_get_name
(Jerome Marchand)
- Fix verifier assumption of nullness of d_inode in dentry (Song Liu)
- Fix global starvation of LRU map (Willem de Bruijn)
- Fix potential NULL dereference in btf_dump__free (Yuan Chen)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: adapt one more case in test_lru_map to the new target_free
libbpf: Fix possible use-after-free for externs
selftests/bpf: Convert test_sysctl to prog_tests
bpf: Specify access type of bpf_sysctl_get_name args
libbpf: Fix null pointer dereference in btf_dump__free on allocation failure
bpf: Adjust free target to avoid global starvation of LRU map
bpf: Mark dentry->d_inode as trusted_or_null
Fix a 6.16 regression from the recovery pass rework, which introduced a
bug where calling bch2_run_explicit_recovery_pass() would only return
the error code to rewind recovery for the first call that scheduled that
recovery pass.
If the error code from the first call was swallowed (because it was
called by an asynchronous codepath), subsequent calls would go "ok, this
pass is already marked as needing to run" and return 0.
Fixing this ensures that check_topology bails out to run btree_node_scan
before doing any repair.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Previously, calling bch2_btree_has_scanned_nodes() when btree node
scan hadn't actually run would erroniously return false - causing us to
think a btree was entirely gone.
This fixes a 6.16 regression from moving the scheduling of btree node
scan out of bch2_btree_lost_data() (fixing the bug where we'd schedule
it persistently in the superblock) and only scheduling it when
check_toploogy() is asking for scanned btree nodes.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Pull mount fixes from Al Viro:
"Several mount-related fixes"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
userns and mnt_idmap leak in open_tree_attr(2)
attach_recursive_mnt(): do not lock the covering tree when sliding something under it
replace collect_mounts()/drop_collected_mounts() with a safer variant
The dm_crypt code fails to build without CONFIG_KEYS:
kernel/crash_dump_dm_crypt.c: In function 'restore_dm_crypt_keys_to_thread_keyring':
kernel/crash_dump_dm_crypt.c:105:9: error: unknown type name 'key_ref_t'; did you mean 'key_ref_put'?
There is a mix of 'select KEYS' and 'depends on KEYS' in Kconfig,
so there is no single obvious solution here, but generally using 'depends on'
makes more sense and is less likely to cause dependency loops.
Link: https://lkml.kernel.org/r/20250620112140.3396316-1-arnd@kernel.org
Fixes: 62f17d9df6 ("crash_dump: retrieve dm crypt keys in kdump kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Coiby Xu <coxu@redhat.com>
Cc: Dave Vasilevsky <dave@vasilevsky.ca>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
memcg_path_store() assigns a newly allocated memory buffer to
filter->memcg_path, without deallocating the previously allocated and
assigned memory buffer. As a result, users can leak kernel memory by
continuously writing a data to memcg_path DAMOS sysfs file. Fix the leak
by deallocating the previously set memory buffer.
Link: https://lkml.kernel.org/r/20250619183608.6647-2-sj@kernel.org
Fixes: 7ee161f18b ("mm/damon/sysfs-schemes: implement filter directory")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org> [6.3.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When loading a module, as long as the module has memory allocation
operations, kmemleak produces a false positive report that resembles the
following:
unreferenced object (percpu) 0x7dfd232a1650 (size 16):
comm "modprobe", pid 1301, jiffies 4294940249
hex dump (first 16 bytes on cpu 2):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 0):
kmemleak_alloc_percpu+0xb4/0xd0
pcpu_alloc_noprof+0x700/0x1098
load_module+0xd4/0x348
codetag_module_init+0x20c/0x450
codetag_load_module+0x70/0xb8
load_module+0xef8/0x1608
init_module_from_file+0xec/0x158
idempotent_init_module+0x354/0x608
__arm64_sys_finit_module+0xbc/0x150
invoke_syscall+0xd4/0x258
el0_svc_common.constprop.0+0xb4/0x240
do_el0_svc+0x48/0x68
el0_svc+0x40/0xf8
el0t_64_sync_handler+0x10c/0x138
el0t_64_sync+0x1ac/0x1b0
This is because the module can only indirectly reference
alloc_tag_counters through the alloc_tag section, which misleads kmemleak.
However, we don't have a kmemleak ignore interface for percpu allocations
yet. So let's create one and invoke it for tag->counters.
[gehao@kylinos.cn: fix build error when CONFIG_DEBUG_KMEMLEAK=n, s/igonore/ignore/]
Link: https://lkml.kernel.org/r/20250620093102.2416767-1-hao.ge@linux.dev
Link: https://lkml.kernel.org/r/20250619183154.2122608-1-hao.ge@linux.dev
Fixes: 12ca42c237 ("alloc_tag: allocate percpu counters for module tags dynamically")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Suren Baghdasaryan <surenb@google.com> [lib/alloc_tag.c]
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
While testing null_blk with configfs, echo 0 > poll_queues will trigger
following panic:
BUG: kernel NULL pointer dereference, address: 0000000000000010
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 27 UID: 0 PID: 920 Comm: bash Not tainted 6.15.0-02023-gadbdb95c8696-dirty #1238 PREEMPT(undef)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:__bitmap_or+0x48/0x70
Call Trace:
<TASK>
__group_cpus_evenly+0x822/0x8c0
group_cpus_evenly+0x2d9/0x490
blk_mq_map_queues+0x1e/0x110
null_map_queues+0xc9/0x170 [null_blk]
blk_mq_update_queue_map+0xdb/0x160
blk_mq_update_nr_hw_queues+0x22b/0x560
nullb_update_nr_hw_queues+0x71/0xf0 [null_blk]
nullb_device_poll_queues_store+0xa4/0x130 [null_blk]
configfs_write_iter+0x109/0x1d0
vfs_write+0x26e/0x6f0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x45c4/0x45f0
do_syscall_64+0xa5/0x240
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Root cause is that numgrps is set to 0, and ZERO_SIZE_PTR is returned from
kcalloc(), and later ZERO_SIZE_PTR will be deferenced.
Fix the problem by checking numgrps first in group_cpus_evenly(), and
return NULL directly if numgrps is zero.
[yukuai3@huawei.com: also fix the non-SMP version]
Link: https://lkml.kernel.org/r/20250620010958.1265984-1-yukuai1@huaweicloud.com
Link: https://lkml.kernel.org/r/20250619132655.3318883-1-yukuai1@huaweicloud.com
Fixes: 6a6dcae8f4 ("blk-mq: Build default queue map via group_cpus_evenly()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Cc: ErKun Yang <yangerkun@huawei.com>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: "zhangyi (F)" <yi.zhang@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In isolate_or_dissolve_huge_folio(), after acquiring the hugetlb_lock, it
is only for the purpose of obtaining the correct hstate, which is then
passed to alloc_and_dissolve_hugetlb_folio().
alloc_and_dissolve_hugetlb_folio() itself also acquires the hugetlb_lock.
We can have alloc_and_dissolve_hugetlb_folio() obtain the hstate by
itself, so that isolate_or_dissolve_huge_folio() no longer needs to
acquire the hugetlb_lock. In addition, we keep the folio_test_hugetlb()
check within isolate_or_dissolve_huge_folio(). By doing so, we can avoid
disrupting the normal path by vainly holding the hugetlb_lock.
replace_free_hugepage_folios() has the same issue, and we should address
it as well.
Addresses a possible performance problem which was added by the hotfix
113ed54ad2 ("mm/hugetlb: fix kernel NULL pointer dereference when
replacing free hugetlb folios").
Link: https://lkml.kernel.org/r/1748317010-16272-1-git-send-email-yangge1116@126.com
Fixes: 113ed54ad2 ("mm/hugetlb: fix kernel NULL pointer dereference when replacing free hugetlb folios")
Signed-off-by: Ge Yang <yangge1116@126.com>
Suggested-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Muchun Song <muchun.song@linux.dev>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Jakub Kicinski says:
====================
netlink: specs: enforce strict naming of properties
I got annoyed once again by the name properties in the ethtool spec
which use underscore instead of dash. I previously assumed that there
is a lot of such properties in the specs so fixing them now would
be near impossible. On a closer look, however, I only found 22
(rough grep suggests we have ~4.8k names in the specs, so bad ones
are just 0.46%).
Add a regex to the JSON schema to enforce the naming, fix the few
bad names. I was hoping we could start enforcing this from newer
families, but there's no correlation between the protocol and the
number of errors. If anything classic netlink has more recently
added specs so it has fewer errors.
The regex is just for name properties which will end up visible
to the user (in Python or YNL CLI). I left the c-name properties
alone, those don't matter as much. C codegen rewrites them, anyway.
I'm not updating the spec for genetlink-c. Looks like it has no
users, new families use genetlink, all old ones need genetlink-legacy.
If these patches are merged I will remove genetlink-c completely
in net-next.
====================
Link: https://patch.msgid.link/20250624211002.3475021-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a regexp to make sure all names which may end up being visible
to the user consist of lower case characters, numbers and dashes.
Underscores keep sneaking into the specs, which is not visible
in the C code but makes the Python and alike inconsistent.
Note that starting with a number is okay, as in C the full
name will include the family name.
For legacy families we can't enforce the naming in the family
name or the multicast group names, as these are part of the
binary uAPI of the kernel.
For classic netlink we need to allow capital letters in names
of struct members. TC has some structs with capitalized members.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-11-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: a1bcfde836 ("doc/netlink/specs: Add a spec for tc")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: b2f63d904e ("doc/netlink: Add spec for rt link messages")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-9-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: bc8aeb2045 ("Documentation: netlink: add a YAML spec for mptcp")
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250624211002.3475021-8-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: 429ac62114 ("devlink: define enum for attr types of dynamic attributes")
Fixes: f2f9dd164d ("netlink: specs: devlink: add the remaining command to generate complete split_ops")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen replaces special chars in names)
but gives more uniform naming in Python.
Fixes: 13e59344fb ("net: ethtool: add support for symmetric-xor RSS hash")
Fixes: 46fb3ba95b ("ethtool: Add an interface for flashing transceiver modules' firmware")
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: 4eb77b4ecd ("netlink: add a proto specification for FOU")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: 13727f85b4 ("NFSD: introduce netlink stubs")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://patch.msgid.link/20250624211002.3475021-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
enetc_hw.h provides two versions of _enetc_rd_reg64.
One which simply calls ioread64() when available.
And another that composes the 64-bit result from ioread32() calls.
In the second case the code appears to assume that each ioread32() call
returns a little-endian value. However both the shift and logical or
used to compose the return value would not work correctly on big endian
systems if this were the case. Moreover, this is inconsistent with the
first case where the return value of ioread64() is assumed to be in host
byte order.
It appears that the correct approach is for both versions to treat the
return value of ioread*() functions as being in host byte order. And
this patch corrects the ioread32()-based version to do so.
This is a bug but would only manifest on big endian systems
that make use of the ioread32-based implementation of _enetc_rd_reg64.
While all in-tree users of this driver are little endian and
make use of the ioread64-based implementation of _enetc_rd_reg64.
Thus, no in-tree user of this driver is affected by this bug.
Flagged by Sparse.
Compile tested only.
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Closes: https://lore.kernel.org/all/AM9PR04MB850500D3FC24FE23DEFCEA158879A@AM9PR04MB8505.eurprd04.prod.outlook.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250624-etnetc-le-v1-1-a73a95d96e4e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The below commit that updated BPF_MAP_TYPE_LRU_HASH free target,
also updated tools/testing/selftests/bpf/test_lru_map to match.
But that missed one case that passes with 4 cores, but fails at
higher cpu counts.
Update test_lru_sanity3 to also adjust its expectation of target_free.
This time tested with 1, 4, 16, 64 and 384 cpu count.
Fixes: d4adf1c9ee ("bpf: Adjust free target to avoid global starvation of LRU map")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20250625210412.2732970-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acknowledge the byte count submitted by the target.
When I2C_SMBUS_BLOCK_DATA read operation is executed by
i2c_smbus_xfer_emulated(), the length of the second (read) message is set
to 1. Length of the block is supposed to be obtained from the target by the
underlying bus driver.
The i2c_imx_isr_read() function should emit the acknowledge on i2c bus
after reading the first byte (i.e., byte count) while processing such
message (as defined in Section 6.5.7 of System Management Bus
Specification [1]). Without this acknowledge, the target does not submit
subsequent bytes and the controller only reads 0xff's.
In addition, store the length of block data obtained from the target in
the buffer provided by i2c_smbus_xfer_emulated() - otherwise the first
byte of actual data is erroneously interpreted as length of the data
block.
[1] https://smbus.org/specs/SMBus_3_3_20240512.pdf
Fixes: 5f5c2d4579 ("i2c: imx: prevent rescheduling in non dma mode")
Signed-off-by: Lukasz Kucharczyk <lukasz.kucharczyk@leica-geosystems.com>
Cc: <stable@vger.kernel.org> # v6.13+
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250520122252.1475403-1-lukasz.kucharczyk@leica-geosystems.com
The `name` field in `obj->externs` points into the BTF data at initial
open time. However, some functions may invalidate this after opening and
before loading (e.g. `bpf_map__set_value_size`), which results in
pointers into freed memory and undefined behavior.
The simplest solution is to simply `strdup` these strings, similar to
the `essent_name`, and free them at the same time.
In order to test this path, the `global_map_resize` BPF selftest is
modified slightly to ensure the presence of an extern, which causes this
test to fail prior to the fix. Given there isn't an obvious API or error
to test against, I opted to add this to the existing test as an aspect
of the resizing feature rather than duplicate the test.
Fixes: 9d0a23313b ("libbpf: Add capability for resizing datasec maps")
Signed-off-by: Adin Scannell <amscanne@meta.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250625050215.2777374-1-amscanne@meta.com
Pull spi fix from Mark Brown:
"One fix for a runtime PM underflow when removing the Cadence QuadSPI
driver"
* tag 'spi-fix-v6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-cadence-quadspi: Fix pm runtime unbalance
Pull SCSI fixes from James Bottomley:
"Fixes all in drivers.
ufs and megaraid_sas are small and obvious.
The large diffstat in fnic comes from two pieces: the addition of
quite a bit of logging (no change to function) and the reworking of
the timeout allocation path for the two conditions that can occur
simultaneously to prevent reusing the same abort frame and then both
trying to free it"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fnic: Fix missing DMA mapping error in fnic_send_frame()
scsi: fnic: Set appropriate logging level for log message
scsi: fnic: Add and improve logs in FDMI and FDMI ABTS paths
scsi: fnic: Turn off FDMI ACTIVE flags on link down
scsi: fnic: Fix crash in fnic_wq_cmpl_handler when FDMI times out
scsi: ufs: core: Fix clk scaling to be conditional in reset and restore
scsi: megaraid_sas: Fix invalid node index
Pull UML fixes from Johannes Berg:
- fix FP registers in seccomp mode
- prevent duplicate devices in VFIO support
- don't ignore errors in UBD thread start
- reduce stack use with clang 19
* tag 'uml-for-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux:
um: vector: Reduce stack usage in vector_eth_configure()
um: Use correct data source in fpregs_legacy_set()
um: vfio: Prevent duplicate device assignments
um: ubd: Add missing error check in start_io_thread()
Johannes Berg says:
====================
Just a few fixes:
- iwlegacy: work around large stack with clang/kasan
- mac80211: fix integer overflow
- mac80211: fix link struct init vs. RCU publish
- iwlwifi: fix warning on IFF_UP
* tag 'wireless-2025-06-25' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: finish link init before RCU publish
wifi: iwlwifi: mvm: assume '1' as the default mac_config_cmd version
wifi: mac80211: fix beacon interval calculation overflow
wifi: iwlegacy: work around excessive stack usage on clang/kasan
====================
Link: https://patch.msgid.link/20250625115433.41381-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A bigger array of vecs could've been allocated, but
io_ring_buffers_peek() still decided to cap the mapped range depending
on how much data was available. Hence don't rely on the segment count
to know if the request should be marked as needing cleanup, always
check upfront if the iov array is different than the fast_iov array.
Fixes: 26ec15e4b0 ("io_uring/kbuf: don't truncate end buffer for multiple buffer peeks")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We should not send smbdirect_data_transfer messages larger than
the negotiated max_send_size, typically 1364 bytes, which means
24 bytes of the smbdirect_data_transfer header + 1340 payload bytes.
This happened when doing an SMB2 write with more than 1340 bytes
(which is done inline as it's below rdma_readwrite_threshold).
It means the peer resets the connection.
When testing between cifs.ko and ksmbd.ko something like this
is logged:
client:
CIFS: VFS: RDMA transport re-established
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
siw: got TERMINATE. layer 1, type 2, code 2
CIFS: VFS: \\carina Send error in SessSetup = -11
smb2_reconnect: 12 callbacks suppressed
CIFS: VFS: reconnect tcon failed rc = -11
CIFS: VFS: reconnect tcon failed rc = -11
CIFS: VFS: reconnect tcon failed rc = -11
CIFS: VFS: SMB: Zero rsize calculated, using minimum value 65536
and:
CIFS: VFS: RDMA transport re-established
siw: got TERMINATE. layer 1, type 2, code 2
CIFS: VFS: smbd_recv:1894 disconnected
siw: got TERMINATE. layer 1, type 2, code 2
The ksmbd dmesg is showing things like:
smb_direct: Recv error. status='local length error (1)' opcode=128
smb_direct: disconnected
smb_direct: Recv error. status='local length error (1)' opcode=128
ksmbd: smb_direct: disconnected
ksmbd: sock_read failed: -107
As smbd_post_send_iter() limits the transmitted number of bytes
we need loop over it in order to transmit the whole iter.
Reviewed-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Tested-by: Meetakshi Setiya <msetiya@microsoft.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: linux-cifs@vger.kernel.org
Cc: <stable+noautosel@kernel.org> # sp->max_send_size should be info->max_send_size in backports
Fixes: 3d78fe73fa ("cifs: Build the RDMA SGE list directly from an iterator")
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
By default, HPD was disabled on SN65DSI86 bridge. When the driver was
added (commit "a095f15c00e27"), the HPD_DISABLE bit was set in pre-enable
call which was moved to other function calls subsequently.
Later on, commit "c312b0df3b13" added detect utility for DP mode. But with
HPD_DISABLE bit set, all the HPD events are disabled[0] and the debounced
state always return 1 (always connected state).
Set HPD_DISABLE bit conditionally based on display sink's connector type.
Since the HPD_STATE is reflected correctly only after waiting for debounce
time (~100-400ms) and adding this delay in detect() is not feasible
owing to the performace impact (glitches and frame drop), remove runtime
calls in detect() and add hpd_enable()/disable() bridge hooks with runtime
calls, to detect hpd properly without any delay.
[0]: <https://www.ti.com/lit/gpn/SN65DSI86> (Pg. 32)
Fixes: c312b0df3b ("drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP")
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250624044835.165708-1-j-choudhary@ti.com
Each Chip-Select (CS) of a Unified Memory Controller (UMC) on AMD Zen-based
SOCs has an Address Mask and a Secondary Address Mask register associated with
it. The amd64_edac module logs DIMM sizes on a per-UMC per-CS granularity
during init using these two registers.
Currently, the module primarily considers only the Address Mask register for
computing DIMM sizes. The Secondary Address Mask register is only considered
for odd CS. Additionally, if it has been considered, the Address Mask register
is ignored altogether for that CS. For power-of-two DIMMs i.e. DIMMs whose
total capacity is a power of two (32GB, 64GB, etc), this is not an issue
since only the Address Mask register is used.
For non-power-of-two DIMMs i.e., DIMMs whose total capacity is not a power of
two (48GB, 96GB, etc), however, the Secondary Address Mask register is used
in conjunction with the Address Mask register. However, since the module only
considers either of the two registers for a CS, the size computed by the
module is incorrect. The Secondary Address Mask register is not considered for
even CS, and the Address Mask register is not considered for odd CS.
Introduce a new helper function so that both Address Mask and Secondary
Address Mask registers are considered, when valid, for computing DIMM sizes.
Furthermore, also rename some variables for greater clarity.
Fixes: 81f5090db8 ("EDAC/amd64: Support asymmetric dual-rank DIMMs")
Closes: https://lore.kernel.org/dbec22b6-00f2-498b-b70d-ab6f8a5ec87e@natrix.lt
Reported-by: Žilvinas Žaltiena <zilvinas@natrix.lt>
Signed-off-by: Avadhut Naik <avadhut.naik@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Žilvinas Žaltiena <zilvinas@natrix.lt>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250529205013.403450-1-avadhut.naik@amd.com
Miri Korenblit says:
====================
iwlwifi-fixes: fix failure in interface up
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When compiling with clang (19.1.7), initializing *vp using a compound
literal may result in excessive stack usage. Fix it by initializing the
required fields of *vp individually.
Without this patch:
$ objdump -d arch/um/drivers/vector_kern.o | ./scripts/checkstack.pl x86_64 0
...
0x0000000000000540 vector_eth_configure [vector_kern.o]:1472
...
With this patch:
$ objdump -d arch/um/drivers/vector_kern.o | ./scripts/checkstack.pl x86_64 0
...
0x0000000000000540 vector_eth_configure [vector_kern.o]:208
...
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506221017.WtB7Usua-lkp@intel.com/
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Link: https://patch.msgid.link/20250623110829.314864-1-tiwei.btw@antgroup.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An earlier patch fixed a build failure with clang, but I still see the
same problem with some configurations using gcc:
drivers/gpu/drm/i915/i915_pmu.c: In function 'config_mask':
include/linux/compiler_types.h:568:38: error: call to '__compiletime_assert_462' declared with attribute error: BUILD_BUG_ON failed: bit > BITS_PER_TYPE(typeof_member(struct i915_pmu, enable)) - 1
drivers/gpu/drm/i915/i915_pmu.c:116:3: note: in expansion of macro 'BUILD_BUG_ON'
116 | BUILD_BUG_ON(bit >
As I understand it, the problem is that the function is not always fully
inlined, but the __builtin_constant_p() can still evaluate the argument
as being constant.
Marking it as __always_inline so far works for me in all configurations.
Fixes: a7137b1825 ("drm/i915/pmu: Fix build error with GCOV and AutoFDO enabled")
Fixes: a644fde77f ("drm/i915/pmu: Change bitmask of enabled events to u32")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250620111824.3395007-1-arnd@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit ef69f9dd1c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
UBLK_F_SUPPORT_ZERO_COPY has a very old comment describing the initial
idea for how zero-copy would be implemented. The actual implementation
added in commit 1f6540e2aa ("ublk: zc register/unregister bvec") uses
io_uring registered buffers rather than shared memory mapping.
Remove the inaccurate remarks about mapping ublk request memory into the
ublk server's address space and requiring 4K block size. Replace them
with a description of the current zero-copy mechanism.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250621171015.354932-1-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a C++ file compiled with -Wc++11-narrowing includes the UAPI header
linux/ublk_cmd.h, ublk_sqe_addr_to_auto_buf_reg()'s assignments of u64
values to u8, u16, and u32 fields result in compiler warnings. Add
explicit casts to the intended types to avoid these warnings. Drop the
unnecessary bitmasks.
Reported-by: Uday Shankar <ushankar@purestorage.com>
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Fixes: 99c1e4eb6a ("ublk: register buffer to local io_uring with provided buf index via UBLK_F_AUTO_BUF_REG")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250621162842.337452-1-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk_queue_cmd_list() dispatches the whole batch list by scheduling task
work via the tail request's io_uring_cmd, this way is fine even though
more than one io_ring_ctx are involved for this batch since it is just
one running context.
However, the task work handler ublk_cmd_list_tw_cb() takes `issue_flags`
of tail uring_cmd's io_ring_ctx for completing all commands. This way is
wrong if any uring_cmd is issued from different io_ring_ctx.
Fixes it by always building batch IOs from same io_ring_ctx and io task
because ublk_dispatch_req() does validate task context, and IO needs to
be aborted in case of running from fallback task work context.
For typical per-queue or per-io daemon implementation, this way shouldn't
make difference from performance viewpoint, because single io_ring_ctx is
taken in each daemon for normal use case.
Fixes: d796cea7b9 ("ublk: implement ->queue_rqs()")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250625022554.883571-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull selinux fix from Paul Moore:
"Another small SELinux patch to fix a problem seen by the dracut-ng
folks during early boot when SELinux is enabled, but the policy has
yet to be loaded"
* tag 'selinux-pr-20250624' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: change security_compute_sid to return the ssid or tsid on match
If a userspace application just include <linux/vm_sockets.h> will fail
to build with the following errors:
/usr/include/linux/vm_sockets.h:182:39: error: invalid application of ‘sizeof’ to incomplete type ‘struct sockaddr’
182 | unsigned char svm_zero[sizeof(struct sockaddr) -
| ^~~~~~
/usr/include/linux/vm_sockets.h:183:39: error: ‘sa_family_t’ undeclared here (not in a function)
183 | sizeof(sa_family_t) -
|
Include <sys/socket.h> for userspace (guarded by ifndef __KERNEL__)
where `struct sockaddr` and `sa_family_t` are defined.
We already do something similar in <linux/mptcp.h> and <linux/if.h>.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reported-by: Daan De Meyer <daan.j.demeyer@gmail.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20250623100053.40979-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initialize DR6 by writing its architectural reset value to avoid
incorrectly zeroing DR6 to clear DR6.BLD at boot time, which leads
to a false bus lock detected warning.
The Intel SDM says:
1) Certain debug exceptions may clear bits 0-3 of DR6.
2) BLD induced #DB clears DR6.BLD and any other debug exception
doesn't modify DR6.BLD.
3) RTM induced #DB clears DR6.RTM and any other debug exception
sets DR6.RTM.
To avoid confusion in identifying debug exceptions, debug handlers
should set DR6.BLD and DR6.RTM, and clear other DR6 bits before
returning.
The DR6 architectural reset value 0xFFFF0FF0, already defined as
macro DR6_RESERVED, satisfies these requirements, so just use it to
reinitialize DR6 whenever needed.
Since clear_all_debug_regs() no longer zeros all debug registers,
rename it to initialize_debug_regs() to better reflect its current
behavior.
Since debug_read_clear_dr6() no longer clears DR6, rename it to
debug_read_reset_dr6() to better reflect its current behavior.
Fixes: ebb1064e7c ("x86/traps: Handle #DB for bus lock")
Reported-by: Sohil Mehta <sohil.mehta@intel.com>
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/lkml/06e68373-a92b-472e-8fd9-ba548119770c@intel.com/
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250620231504.2676902-2-xin%40zytor.com
Prevent other bits of mailbox power limit from being overwritten with 0.
This issue was due to a missing read and modify of current power limit,
before setting a requested mailbox power limit, which is added in this
patch.
v2:
- Improve commit message. (Anshuman)
v3:
- Rebase.
- Rephrase commit message. (Riana)
- Add read-modify-write variant of xe_hwmon_pcode_write_power_limit()
i.e. xe_hwmon_pcode_rmw_power_limit(). (Badal)
- Use xe_hwmon_pcode_rmw_power_limit() to set mailbox power limits.
- Remove xe_hwmon_pcode_write_power_limit() as all mailbox power limits
writes use xe_hwmon_pcode_rmw_power_limit() only.
v4:
- Use PWR_LIM in place of (PWR_LIM_EN | PWR_LIM_VAL) wherever
applicable. (Riana)
Fixes: 25a2aa779f ("drm/xe/hwmon: Add support to manage power limits though mailbox")
Reviewed-by: Riana Tauro <riana.tauro@intel.com>
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Link: https://lore.kernel.org/r/20250617120030.612819-1-karthik.poosa@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 8aa7306631)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Having PM put sync in remove function is causing PM underflow during
remove operation. This is caused by the function, runtime_pm_get_sync,
not being called anywhere during the op. Ensure that calls to
pm_runtime_enable()/pm_runtime_disable() and
pm_runtime_get_sync()/pm_runtime_put_sync() match.
echo 108d2000.spi > /sys/bus/platform/drivers/cadence-qspi/unbind
[ 49.644256] Deleting MTD partitions on "108d2000.spi.0":
[ 49.649575] Deleting u-boot MTD partition
[ 49.684087] Deleting root MTD partition
[ 49.724188] cadence-qspi 108d2000.spi: Runtime PM usage count underflow!
Continuous bind/unbind will result in an "Unbalanced pm_runtime_enable" error.
Subsequent unbind attempts will return a "No such device" error, while bind
attempts will return a "Resource temporarily unavailable" error.
[ 47.592434] cadence-qspi 108d2000.spi: Runtime PM usage count underflow!
[ 49.592233] cadence-qspi 108d2000.spi: detected FIFO depth (1024) different from config (128)
[ 53.232309] cadence-qspi 108d2000.spi: Runtime PM usage count underflow!
[ 55.828550] cadence-qspi 108d2000.spi: detected FIFO depth (1024) different from config (128)
[ 57.940627] cadence-qspi 108d2000.spi: Runtime PM usage count underflow!
[ 59.912490] cadence-qspi 108d2000.spi: detected FIFO depth (1024) different from config (128)
[ 61.876243] cadence-qspi 108d2000.spi: Runtime PM usage count underflow!
[ 61.883000] platform 108d2000.spi: Unbalanced pm_runtime_enable!
[ 532.012270] cadence-qspi 108d2000.spi: probe with driver cadence-qspi failed1
Also, change clk_disable_unprepare() to clk_disable() since continuous
bind and unbind operations will trigger a warning indicating that the clock is
already unprepared.
Fixes: 4892b374c9 ("mtd: spi-nor: cadence-quadspi: Add runtime PM support")
cc: stable@vger.kernel.org # 6.6+
Signed-off-by: Khairul Anuar Romli <khairul.anuar.romli@altera.com>
Reviewed-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/4e7a4b8aba300e629b45a04f90bddf665fbdb335.1749601877.git.khairul.anuar.romli@altera.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When EDID is retrieved via drm_edid_raw(), it doesn't guarantee to
return proper EDID bytes the caller wants: it may be either NULL (that
leads to an Oops) or with too long bytes over the fixed size raw_edid
array (that may lead to memory corruption). The latter was reported
actually when connected with a bad adapter.
Add sanity checks for drm_edid_raw() to address the above corner
cases, and return EDID_BAD_INPUT accordingly.
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1236415
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 648d3f4d20)
Cc: stable@vger.kernel.org
Enable the cleaner shader for other GFX9.x series of GPUs to provide
data isolation between GPU workloads. The cleaner shader is responsible
for clearing the Local Data Store (LDS), Vector General Purpose
Registers (VGPRs), and Scalar General Purpose Registers (SGPRs), which
helps prevent data leakage and ensures accurate computation results.
This update extends cleaner shader support to GFX9.x GPUs, previously
available for GFX9.4.2. It enhances security by clearing GPU memory
between processes and maintains a consistent GPU state across KGD and
KFD workloads.
Cc: Manu Rastogi <manu.rastogi@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 99808926d0)
The 8250 binding before converting to json-schema states,
- clock-frequency : the input clock frequency for the UART
or
- clocks phandle to refer to the clk used as per Documentation/devicetree
for clock-related properties, where "or" indicates these properties
shouldn't exist at the same time.
Additionally, the behavior of Linux's driver is strange when both clocks
and clock-frequency are specified: it ignores clocks and obtains the
frequency from clock-frequency, left the specified clocks unclaimed. It
may even be disabled, which is undesired most of the time.
But "anyOf" doesn't prevent these two properties from coexisting, as it
considers the object valid as long as there's at LEAST one match.
Let's switch to "oneOf" and disallows the other property if one exists,
precisely matching the original binding and avoiding future confusion on
the driver's behavior.
Fixes: e69f5dc623 ("dt-bindings: serial: Convert 8250 to json-schema")
Cc: stable <stable@kernel.org>
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250623093445.62327-1-ziyao@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
introduced a regression on the i.MX6UL EVK board. The issue can be
reproduced with the following steps:
- Open vi on the board.
- Paste a text file (~150 characters).
- Save the file, then repeat the process.
- Compare the sha256sum of the saved files.
The checksums do not match due to missing characters or entire lines.
Fix this by restoring the RXTL value to 1 when the UART is used as a
console.
This ensures timely RX interrupts and reliable data reception in console
mode.
With this change, pasted content is saved correctly, and checksums are
always consistent.
Cc: stable <stable@kernel.org>
Fixes: 7a637784d5 ("serial: imx: reduce RX interrupt frequency")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250619114617.2791939-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once want_mount_setattr() has returned a positive, it does require
finish_mount_kattr() to release ->mnt_userns. Failing do_mount_setattr()
does not change that.
As the result, we can end up leaking userns and possibly mnt_idmap as
well.
Fixes: c4a16820d9 ("fs: add open_tree_attr()")
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- L2CAP: Fix L2CAP MTU negotiation
- hci_core: Fix use-after-free in vhci_flush()
- btintel_pcie: Fix potential race condition in firmware download
- hci_qca: fix unable to load the BT driver
* tag 'for-net-2025-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: hci_core: Fix use-after-free in vhci_flush()
driver: bluetooth: hci_qca:fix unable to load the BT driver
Bluetooth: L2CAP: Fix L2CAP MTU negotiation
Bluetooth: btintel_pcie: Fix potential race condition in firmware download
====================
Link: https://patch.msgid.link/20250623165405.227619-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Unfortunately, FWs of some devices don't have the version of the
iwl_mac_config_cmd defined in the TLVs. We send 0 as the 'def argument
to iwl_fw_lookup_cmd_ver, so for such FWs, the return value will be 0,
leading to a warning, and to not sending the command.
Fix this by assuming that the default version is 1.
Fixes: 83f3ac2848 ("wifi: iwlwifi: Fix incorrect logic on cmd_ver range checking")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250624071427.2662621-1-miriam.rachel.korenblit@intel.com
A new function resetpair() calls close() for the receiver and checks
the return value from recv() on the initial sender side.
Now resetpair() is added to each test case and some additional test
cases.
Note that TCP sets -ECONNRESET to the consumed OOB, but we have decided
not to touch TCP MSG_OOB code in the past.
Before:
# RUN msg_oob.no_peek.ex_oob_ex_oob ...
# msg_oob.c:236:ex_oob_ex_oob:AF_UNIX :Connection reset by peer
# msg_oob.c:237:ex_oob_ex_oob:Expected:
# msg_oob.c:239:ex_oob_ex_oob:Expected ret[0] (-1) == expected_len (0)
# ex_oob_ex_oob: Test terminated by assertion
# FAIL msg_oob.no_peek.ex_oob_ex_oob
not ok 14 msg_oob.no_peek.ex_oob_ex_oob
...
# FAILED: 36 / 48 tests passed.
# Totals: pass:36 fail:12 xfail:0 xpass:0 skip:0 error:0
After:
# RUN msg_oob.no_peek.ex_oob_ex_oob ...
# msg_oob.c:244:ex_oob_ex_oob:AF_UNIX :
# msg_oob.c:245:ex_oob_ex_oob:TCP :Connection reset by peer
# OK msg_oob.no_peek.ex_oob_ex_oob
ok 14 msg_oob.no_peek.ex_oob_ex_oob
...
# PASSED: 48 / 48 tests passed.
# Totals: pass:48 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250619041457.1132791-5-kuni1840@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Christian Brauner reported that even after MSG_OOB data is consumed,
calling close() on the receiver socket causes the peer's recv() to
return -ECONNRESET:
1. send() and recv() an OOB data.
>>> from socket import *
>>> s1, s2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> s1.send(b'x', MSG_OOB)
1
>>> s2.recv(1, MSG_OOB)
b'x'
2. close() for s2 sets ECONNRESET to s1->sk_err even though
s2 consumed the OOB data
>>> s2.close()
>>> s1.recv(10, MSG_DONTWAIT)
...
ConnectionResetError: [Errno 104] Connection reset by peer
Even after being consumed, the skb holding the OOB 1-byte data stays in
the recv queue to mark the OOB boundary and break recv() at that point.
This must be considered while close()ing a socket.
Let's skip the leading consumed OOB skb while checking the -ECONNRESET
condition in unix_release_sock().
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: Christian Brauner <brauner@kernel.org>
Closes: https://lore.kernel.org/netdev/20250529-sinkt-abfeuern-e7b08200c6b0@brauner/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://patch.msgid.link/20250619041457.1132791-4-kuni1840@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Let's add a test case where consecutive concumed OOB skbs stay
at the head of the queue.
Without the previous patch, ioctl(SIOCATMARK) assertion fails.
Before:
# RUN msg_oob.no_peek.ex_oob_ex_oob_oob ...
# msg_oob.c:305:ex_oob_ex_oob_oob:Expected answ[0] (0) == oob_head (1)
# ex_oob_ex_oob_oob: Test terminated by assertion
# FAIL msg_oob.no_peek.ex_oob_ex_oob_oob
not ok 12 msg_oob.no_peek.ex_oob_ex_oob_oob
After:
# RUN msg_oob.no_peek.ex_oob_ex_oob_oob ...
# OK msg_oob.no_peek.ex_oob_ex_oob_oob
ok 12 msg_oob.no_peek.ex_oob_ex_oob_oob
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250619041457.1132791-3-kuni1840@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jann Horn reported a use-after-free in unix_stream_read_generic().
The following sequences reproduce the issue:
$ python3
from socket import *
s1, s2 = socketpair(AF_UNIX, SOCK_STREAM)
s1.send(b'x', MSG_OOB)
s2.recv(1, MSG_OOB) # leave a consumed OOB skb
s1.send(b'y', MSG_OOB)
s2.recv(1, MSG_OOB) # leave a consumed OOB skb
s1.send(b'z', MSG_OOB)
s2.recv(1) # recv 'z' illegally
s2.recv(1, MSG_OOB) # access 'z' skb (use-after-free)
Even though a user reads OOB data, the skb holding the data stays on
the recv queue to mark the OOB boundary and break the next recv().
After the last send() in the scenario above, the sk2's recv queue has
2 leading consumed OOB skbs and 1 real OOB skb.
Then, the following happens during the next recv() without MSG_OOB
1. unix_stream_read_generic() peeks the first consumed OOB skb
2. manage_oob() returns the next consumed OOB skb
3. unix_stream_read_generic() fetches the next not-yet-consumed OOB skb
4. unix_stream_read_generic() reads and frees the OOB skb
, and the last recv(MSG_OOB) triggers KASAN splat.
The 3. above occurs because of the SO_PEEK_OFF code, which does not
expect unix_skb_len(skb) to be 0, but this is true for such consumed
OOB skbs.
while (skip >= unix_skb_len(skb)) {
skip -= unix_skb_len(skb);
skb = skb_peek_next(skb, &sk->sk_receive_queue);
...
}
In addition to this use-after-free, there is another issue that
ioctl(SIOCATMARK) does not function properly with consecutive consumed
OOB skbs.
So, nothing good comes out of such a situation.
Instead of complicating manage_oob(), ioctl() handling, and the next
ECONNRESET fix by introducing a loop for consecutive consumed OOB skbs,
let's not leave such consecutive OOB unnecessarily.
Now, while receiving an OOB skb in unix_stream_recv_urg(), if its
previous skb is a consumed OOB skb, it is freed.
[0]:
BUG: KASAN: slab-use-after-free in unix_stream_read_actor (net/unix/af_unix.c:3027)
Read of size 4 at addr ffff888106ef2904 by task python3/315
CPU: 2 UID: 0 PID: 315 Comm: python3 Not tainted 6.16.0-rc1-00407-gec315832f6f9 #8 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-4.fc42 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:122)
print_report (mm/kasan/report.c:409 mm/kasan/report.c:521)
kasan_report (mm/kasan/report.c:636)
unix_stream_read_actor (net/unix/af_unix.c:3027)
unix_stream_read_generic (net/unix/af_unix.c:2708 net/unix/af_unix.c:2847)
unix_stream_recvmsg (net/unix/af_unix.c:3048)
sock_recvmsg (net/socket.c:1063 (discriminator 20) net/socket.c:1085 (discriminator 20))
__sys_recvfrom (net/socket.c:2278)
__x64_sys_recvfrom (net/socket.c:2291 (discriminator 1) net/socket.c:2287 (discriminator 1) net/socket.c:2287 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f8911fcea06
Code: 5d e8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 75 19 83 e2 39 83 fa 08 75 11 e8 26 ff ff ff 66 0f 1f 44 00 00 48 8b 45 10 0f 05 <48> 8b 5d f8 c9 c3 0f 1f 40 00 f3 0f 1e fa 55 48 89 e5 48 83 ec 08
RSP: 002b:00007fffdb0dccb0 EFLAGS: 00000202 ORIG_RAX: 000000000000002d
RAX: ffffffffffffffda RBX: 00007fffdb0dcdc8 RCX: 00007f8911fcea06
RDX: 0000000000000001 RSI: 00007f8911a5e060 RDI: 0000000000000006
RBP: 00007fffdb0dccd0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000202 R12: 00007f89119a7d20
R13: ffffffffc4653600 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Allocated by task 315:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:60 (discriminator 1) mm/kasan/common.c:69 (discriminator 1))
__kasan_slab_alloc (mm/kasan/common.c:348)
kmem_cache_alloc_node_noprof (./include/linux/kasan.h:250 mm/slub.c:4148 mm/slub.c:4197 mm/slub.c:4249)
__alloc_skb (net/core/skbuff.c:660 (discriminator 4))
alloc_skb_with_frags (./include/linux/skbuff.h:1336 net/core/skbuff.c:6668)
sock_alloc_send_pskb (net/core/sock.c:2993)
unix_stream_sendmsg (./include/net/sock.h:1847 net/unix/af_unix.c:2256 net/unix/af_unix.c:2418)
__sys_sendto (net/socket.c:712 (discriminator 20) net/socket.c:727 (discriminator 20) net/socket.c:2226 (discriminator 20))
__x64_sys_sendto (net/socket.c:2233 (discriminator 1) net/socket.c:2229 (discriminator 1) net/socket.c:2229 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Freed by task 315:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:60 (discriminator 1) mm/kasan/common.c:69 (discriminator 1))
kasan_save_free_info (mm/kasan/generic.c:579 (discriminator 1))
__kasan_slab_free (mm/kasan/common.c:271)
kmem_cache_free (mm/slub.c:4643 (discriminator 3) mm/slub.c:4745 (discriminator 3))
unix_stream_read_generic (net/unix/af_unix.c:3010)
unix_stream_recvmsg (net/unix/af_unix.c:3048)
sock_recvmsg (net/socket.c:1063 (discriminator 20) net/socket.c:1085 (discriminator 20))
__sys_recvfrom (net/socket.c:2278)
__x64_sys_recvfrom (net/socket.c:2291 (discriminator 1) net/socket.c:2287 (discriminator 1) net/socket.c:2287 (discriminator 1))
do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
The buggy address belongs to the object at ffff888106ef28c0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 68 bytes inside of
freed 224-byte region [ffff888106ef28c0, ffff888106ef29a0)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff888106ef3cc0 pfn:0x106ef2
head: order:1 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x200000000000040(head|node=0|zone=2)
page_type: f5(slab)
raw: 0200000000000040 ffff8881001d28c0 ffffea000422fe00 0000000000000004
raw: ffff888106ef3cc0 0000000080190010 00000000f5000000 0000000000000000
head: 0200000000000040 ffff8881001d28c0 ffffea000422fe00 0000000000000004
head: ffff888106ef3cc0 0000000080190010 00000000f5000000 0000000000000000
head: 0200000000000001 ffffea00041bbc81 00000000ffffffff 00000000ffffffff
head: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888106ef2800: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
ffff888106ef2880: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
>ffff888106ef2900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888106ef2980: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
ffff888106ef2a00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://patch.msgid.link/20250619041457.1132791-2-kuni1840@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In some rare randconfig builds, I seem to trigger a bug in clang where
it unrolls a loop but then runs out of registers, which then get
spilled to the stack:
net/wireless/intel/iwlegacy/4965-rs.c:2262:1: error: stack frame size (1696) exceeds limit (1280) in 'il4965_rs_rate_init' [-Werror,-Wframe-larger-than]
This seems to be the same one I saw in the omapdrm driver, and there is
an easy workaround by not inlining the il4965_rs_rate_scale_clear_win
function.
Link: https://github.com/llvm/llvm-project/issues/143908
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250620113946.3987160-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jerome Marchand says:
====================
bpf: Specify access type of bpf_sysctl_get_name args
The second argument of bpf_sysctl_get_name() helper is a pointer to a
buffer that is being written to. However that isn't specify in the
prototype. Until commit 37cce22dbd ("bpf: verifier: Refactor helper
access type tracking") that mistake was hidden by the way the verifier
treated helper accesses. Since then, the verifier, working on wrong
infromation from the prototype, can make faulty optimization that
would had been caught by the test_sysctl selftests if it was run by
the CI.
The first patch fixes bpf_sysctl_get_name prototype.
The second patch converts the test_sysctl to prog_tests so that it
will be run by the CI and catch similar issues in the future.
Changes in v3:
- Use ASSERT* macro instead of CHECK_FAIL.
- Remove useless code.
Changes in v2:
- Replace ARG_PTR_TO_UNINIT_MEM by ARG_PTR_TO_MEM | MEM_WRITE.
- Converts test_sysctl to prog_tests.
====================
Link: https://patch.msgid.link/20250619140603.148942-1-jmarchan@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The second argument of bpf_sysctl_get_name() helper is a pointer to a
buffer that is being written to. However that isn't specify in the
prototype.
Until commit 37cce22dbd ("bpf: verifier: Refactor helper access
type tracking"), all helper accesses were considered as a possible
write access by the verifier, so no big harm was done. However, since
then, the verifier might make wrong asssumption about the content of
that address which might lead it to make faulty optimizations (such as
removing code that was wrongly labeled dead). This is what happens in
test_sysctl selftest to the tests related to sysctl_get_name.
Add MEM_WRITE flag the second argument of bpf_sysctl_get_name().
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20250619140603.148942-2-jmarchan@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The bridge maintains a global list of ports behind which a multicast
router resides. The list is consulted during forwarding to ensure
multicast packets are forwarded to these ports even if the ports are not
member in the matching MDB entry.
When per-VLAN multicast snooping is enabled, the per-port multicast
context is disabled on each port and the port is removed from the global
router port list:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1
# ip link add name dummy1 up master br1 type dummy
# ip link set dev dummy1 type bridge_slave mcast_router 2
$ bridge -d mdb show | grep router
router ports on br1: dummy1
# ip link set dev br1 type bridge mcast_vlan_snooping 1
$ bridge -d mdb show | grep router
However, the port can be re-added to the global list even when per-VLAN
multicast snooping is enabled:
# ip link set dev dummy1 type bridge_slave mcast_router 0
# ip link set dev dummy1 type bridge_slave mcast_router 2
$ bridge -d mdb show | grep router
router ports on br1: dummy1
Since commit 4b30ae9adb ("net: bridge: mcast: re-implement
br_multicast_{enable, disable}_port functions"), when per-VLAN multicast
snooping is enabled, multicast disablement on a port will disable the
per-{port, VLAN} multicast contexts and not the per-port one. As a
result, a port will remain in the global router port list even after it
is deleted. This will lead to a use-after-free [1] when the list is
traversed (when adding a new port to the list, for example):
# ip link del dev dummy1
# ip link add name dummy2 up master br1 type dummy
# ip link set dev dummy2 type bridge_slave mcast_router 2
Similarly, stale entries can also be found in the per-VLAN router port
list. When per-VLAN multicast snooping is disabled, the per-{port, VLAN}
contexts are disabled on each port and the port is removed from the
per-VLAN router port list:
# ip link add name br1 up type bridge vlan_filtering 1 mcast_snooping 1 mcast_vlan_snooping 1
# ip link add name dummy1 up master br1 type dummy
# bridge vlan add vid 2 dev dummy1
# bridge vlan global set vid 2 dev br1 mcast_snooping 1
# bridge vlan set vid 2 dev dummy1 mcast_router 2
$ bridge vlan global show dev br1 vid 2 | grep router
router ports: dummy1
# ip link set dev br1 type bridge mcast_vlan_snooping 0
$ bridge vlan global show dev br1 vid 2 | grep router
However, the port can be re-added to the per-VLAN list even when
per-VLAN multicast snooping is disabled:
# bridge vlan set vid 2 dev dummy1 mcast_router 0
# bridge vlan set vid 2 dev dummy1 mcast_router 2
$ bridge vlan global show dev br1 vid 2 | grep router
router ports: dummy1
When the VLAN is deleted from the port, the per-{port, VLAN} multicast
context will not be disabled since multicast snooping is not enabled
on the VLAN. As a result, the port will remain in the per-VLAN router
port list even after it is no longer member in the VLAN. This will lead
to a use-after-free [2] when the list is traversed (when adding a new
port to the list, for example):
# ip link add name dummy2 up master br1 type dummy
# bridge vlan add vid 2 dev dummy2
# bridge vlan del vid 2 dev dummy1
# bridge vlan set vid 2 dev dummy2 mcast_router 2
Fix these issues by removing the port from the relevant (global or
per-VLAN) router port list in br_multicast_port_ctx_deinit(). The
function is invoked during port deletion with the per-port multicast
context and during VLAN deletion with the per-{port, VLAN} multicast
context.
Note that deleting the multicast router timer is not enough as it only
takes care of the temporary multicast router states (1 or 3) and not the
permanent one (2).
[1]
BUG: KASAN: slab-out-of-bounds in br_multicast_add_router.part.0+0x3f1/0x560
Write of size 8 at addr ffff888004a67328 by task ip/384
[...]
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6f/0x350
print_report+0x108/0x205
kasan_report+0xdf/0x110
br_multicast_add_router.part.0+0x3f1/0x560
br_multicast_set_port_router+0x74e/0xac0
br_setport+0xa55/0x1870
br_port_slave_changelink+0x95/0x120
__rtnl_newlink+0x5e8/0xa40
rtnl_newlink+0x627/0xb00
rtnetlink_rcv_msg+0x6fb/0xb70
netlink_rcv_skb+0x11f/0x350
netlink_unicast+0x426/0x710
netlink_sendmsg+0x75a/0xc20
__sock_sendmsg+0xc1/0x150
____sys_sendmsg+0x5aa/0x7b0
___sys_sendmsg+0xfc/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0x360
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[2]
BUG: KASAN: slab-use-after-free in br_multicast_add_router.part.0+0x378/0x560
Read of size 8 at addr ffff888009f00840 by task bridge/391
[...]
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6f/0x350
print_report+0x108/0x205
kasan_report+0xdf/0x110
br_multicast_add_router.part.0+0x378/0x560
br_multicast_set_port_router+0x6f9/0xac0
br_vlan_process_options+0x8b6/0x1430
br_vlan_rtm_process_one+0x605/0xa30
br_vlan_rtm_process+0x396/0x4c0
rtnetlink_rcv_msg+0x2f7/0xb70
netlink_rcv_skb+0x11f/0x350
netlink_unicast+0x426/0x710
netlink_sendmsg+0x75a/0xc20
__sock_sendmsg+0xc1/0x150
____sys_sendmsg+0x5aa/0x7b0
___sys_sendmsg+0xfc/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0x360
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: 2796d846d7 ("net: bridge: vlan: convert mcast router global option to per-vlan entry")
Fixes: 4b30ae9adb ("net: bridge: mcast: re-implement br_multicast_{enable, disable}_port functions")
Reported-by: syzbot+7bfa4b72c6a5da128d32@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/684c18bd.a00a0220.279073.000b.GAE@google.com/T/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250619182228.1656906-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change error values of `ionic_tx_map_single()` and `ionic_tx_map_frag()`
from 0 to `DMA_MAPPING_ERROR` to prevent collision with 0 as a valid
address.
This also fixes the use of `dma_mapping_error()` to test against 0 in
`ionic_xdp_post_frame()`
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Fixes: 56e41ee12d ("ionic: better dma-map error handling")
Fixes: ac8813c0ab ("ionic: convert Rx queue buffers to use page_pool")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20250619094538.283723-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit ad5643cf2f ("riscv: Define TASK_SIZE_MAX for
__access_ok()").
This commit changes TASK_SIZE_MAX to be LONG_MAX to optimize access_ok(),
because the previous TASK_SIZE_MAX (default to TASK_SIZE) requires some
computation.
The reasoning was that all user addresses are less than LONG_MAX, and all
kernel addresses are greater than LONG_MAX. Therefore access_ok() can
filter kernel addresses.
Addresses between TASK_SIZE and LONG_MAX are not valid user addresses, but
access_ok() let them pass. That was thought to be okay, because they are
not valid addresses at hardware level.
Unfortunately, one case is missed: get_user_pages_fast() happily accepts
addresses between TASK_SIZE and LONG_MAX. futex(), for instance, uses
get_user_pages_fast(). This causes the problem reported by Robert [1].
Therefore, revert this commit. TASK_SIZE_MAX is changed to the default:
TASK_SIZE.
This unfortunately reduces performance, because TASK_SIZE is more expensive
to compute compared to LONG_MAX. But correctness first, we can think about
optimization later, if required.
Reported-by: <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/linux-riscv/77605.1750245028@localhost/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: ad5643cf2f ("riscv: Define TASK_SIZE_MAX for __access_ok()")
Link: https://lore.kernel.org/r/20250619155858.1249789-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Pull device mapper fixes from Mikulas Patocka:
- dm-crypt: fix a crash on 32-bit machines
- dm-raid: replace "rdev" with correct loop variable name "r"
* tag 'for-6.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-raid: fix variable in journal device check
dm-crypt: Extend state buffer size in crypt_iv_lmk_one
Pull f2fs fixes from Jaegeuk Kim:
- fix double-unlock introduced by the recent folio conversion
- fix stale page content beyond EOF complained by xfstests/generic/363
* tag 'f2fs-for-6.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: fix to zero post-eof page
f2fs: Fix __write_node_folio() conversion
Pull btrfs fixes from David Sterba:
"Fixes:
- fix invalid inode pointer dereferences during log replay
- fix a race between renames and directory logging
- fix shutting down delayed iput worker
- fix device byte accounting when dropping chunk
- in zoned mode, fix offset calculations for DUP profile when
conventional and sequential zones are used together
Regression fixes:
- fix possible double unlock of extent buffer tree (xarray
conversion)
- in zoned mode, fix extent buffer refcount when writing out extents
(xarray conversion)
Error handling fixes and updates:
- handle unexpected extent type when replaying log
- check and warn if there are remaining delayed inodes when putting a
root
- fix assertion when building free space tree
- handle csum tree error with mount option 'rescue=ibadroot'
Other:
- error message updates: add prefix to all scrub related messages,
include other information in messages"
* tag 'for-6.16-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix alloc_offset calculation for partly conventional block groups
btrfs: handle csum tree error with rescue=ibadroots correctly
btrfs: fix race between async reclaim worker and close_ctree()
btrfs: fix assertion when building free space tree
btrfs: don't silently ignore unexpected extent type when replaying log
btrfs: fix invalid inode pointer dereferences during log replay
btrfs: fix double unlock of buffer_tree xarray when releasing subpage eb
btrfs: update superblock's device bytes_used when dropping chunk
btrfs: fix a race between renames and directory logging
btrfs: scrub: add prefix for the error messages
btrfs: warn if leaking delayed_nodes in btrfs_put_root()
btrfs: fix delayed ref refcount leak in debug assertion
btrfs: include root in error message when unlinking inode
btrfs: don't drop a reference if btrfs_check_write_meta_pointer() fails
When btf_dump__new() fails to allocate memory for the internal hashmap
(btf_dump->type_names), it returns an error code. However, the cleanup
function btf_dump__free() does not check if btf_dump->type_names is NULL
before attempting to free it. This leads to a null pointer dereference
when btf_dump__free() is called on a btf_dump object.
Fixes: 351131b51c ("libbpf: add btf_dump API for BTF-to-C conversion")
Signed-off-by: Yuan Chen <chenyuan@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250618011933.11423-1-chenyuan_fl@163.com
If we are propagating across the userns boundary, we need to lock the
mounts added there. However, in case when something has already
been mounted there and we end up sliding a new tree under that,
the stuff that had been there before should not get locked.
IOW, lock_mnt_tree() should be called before we reparent the
preexisting tree on top of what we are adding.
Fixes: 3bd045cc9c ("separate copying and locking mount tree on cross-userns copies")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
collect_mounts() has several problems - one can't iterate over the results
directly, so it has to be done with callback passed to iterate_mounts();
it has an oopsable race with d_invalidate(); it creates temporary clones
of mounts invisibly for sync umount (IOW, you can have non-lazy umount
succeed leaving filesystem not mounted anywhere and yet still busy).
A saner approach is to give caller an array of struct path that would pin
every mount in a subtree, without cloning any mounts.
* collect_mounts()/drop_collected_mounts()/iterate_mounts() is gone
* collect_paths(where, preallocated, size) gives either ERR_PTR(-E...) or
a pointer to array of struct path, one for each chunk of tree visible under
'where' (i.e. the first element is a copy of where, followed by (mount,root)
for everything mounted under it - the same set collect_mounts() would give).
Unlike collect_mounts(), the mounts are *not* cloned - we just get pinning
references to the roots of subtrees in the caller's namespace.
Array is terminated by {NULL, NULL} struct path. If it fits into
preallocated array (on-stack, normally), that's where it goes; otherwise
it's allocated by kmalloc_array(). Passing 0 as size means that 'preallocated'
is ignored (and expected to be NULL).
* drop_collected_paths(paths, preallocated) is given the array returned
by an earlier call of collect_paths() and the preallocated array passed to that
call. All mount/dentry references are dropped and array is kfree'd if it's not
equal to 'preallocated'.
* instead of iterate_mounts(), users should just iterate over array
of struct path - nothing exotic is needed for that. Existing users (all in
audit_tree.c) are converted.
[folded a fix for braino reported by Venkat Rao Bagalkote <venkat88@linux.ibm.com>]
Fixes: 80b5dce8c5 ("vfs: Add a function to lazily unmount all mounts from any dentry")
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull misc fixes from Andrew Morton:
"20 hotfixes. 7 are cc:stable and the remainder address post-6.15
issues or aren't considered necessary for -stable kernels. Only 4 are
for MM.
- The series `Revert "bcache: update min_heap_callbacks to use
default builtin swap"' from Kuan-Wei Chiu backs out the author's
recent min_heap changes due to a performance regression.
A fix for this regression has been developed but we felt it best to
go back to the known-good version to give the new code more bake
time.
- A lot of MAINTAINERS maintenance.
I like to get these changes upstreamed promptly because they can't
break things and more accurate/complete MAINTAINERS info hopefully
improves the speed and accuracy of our responses to submitters and
reporters"
* tag 'mm-hotfixes-stable-2025-06-22-18-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS: add additional mmap-related files to mmap section
MAINTAINERS: add memfd, shmem quota files to shmem section
MAINTAINERS: add stray rmap file to mm rmap section
MAINTAINERS: add hugetlb_cgroup.c to hugetlb section
MAINTAINERS: add further init files to mm init block
MAINTAINERS: update maintainers for HugeTLB
maple_tree: fix MA_STATE_PREALLOC flag in mas_preallocate()
MAINTAINERS: add missing test files to mm gup section
MAINTAINERS: add missing mm/workingset.c file to mm reclaim section
selftests/mm: skip uprobe vma merge test if uprobes are not enabled
bcache: remove unnecessary select MIN_HEAP
Revert "bcache: remove heap-related macros and switch to generic min_heap"
Revert "bcache: update min_heap_callbacks to use default builtin swap"
selftests/mm: add configs to fix testcase failure
kho: initialize tail pages for higher order folios properly
MAINTAINERS: add linux-mm@ list to Kexec Handover
mm: userfaultfd: fix race of userfaultfd_move and swap cache
mm/gup: revert "mm: gup: fix infinite loop within __get_longterm_locked"
selftests/mm: increase timeout from 180 to 900 seconds
mm/shmem, swap: fix softlockup with mTHP swapin
In snd_usb_get_audioformat_uac3(), the length value returned from
snd_usb_ctl_msg() is used directly for memory allocation without
validation. This length is controlled by the USB device.
The allocated buffer is cast to a uac3_cluster_header_descriptor
and its fields are accessed without verifying that the buffer
is large enough. If the device returns a smaller than expected
length, this leads to an out-of-bounds read.
Add a length check to ensure the buffer is large enough for
uac3_cluster_header_descriptor.
Signed-off-by: Youngjun Lee <yjjuny.lee@samsung.com>
Fixes: 9a2fe9b801 ("ALSA: usb: initial USB Audio Device Class 3.0 support")
Link: https://patch.msgid.link/20250623-uac3-oob-fix-v1-1-527303eaf40a@samsung.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/namei.c:4046
do_filp_open+0x1fa/0x410 fs/namei.c:4073
do_sys_openat2+0x121/0x1c0 fs/open.c:1437
do_sys_open fs/open.c:1452 [inline]
__do_sys_openat fs/open.c:1468 [inline]
__se_sys_openat fs/open.c:1463 [inline]
__x64_sys_openat+0x138/0x170 fs/open.c:1463
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2381 [inline]
slab_free mm/slub.c:4643 [inline]
kfree+0x18e/0x440 mm/slub.c:4842
vhci_release+0xbc/0xd0 drivers/bluetooth/hci_vhci.c:671
__fput+0x44c/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x6ad/0x22e0 kernel/exit.c:955
do_group_exit+0x21c/0x2d0 kernel/exit.c:1104
__do_sys_exit_group kernel/exit.c:1115 [inline]
__se_sys_exit_group kernel/exit.c:1113 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1113
x64_sys_call+0x21ba/0x21c0 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff88807cb8d800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 88 bytes inside of
freed 1024-byte region [ffff88807cb8d800, ffff88807cb8dc00)
Fixes: bf18c7118c ("Bluetooth: vhci: Free driver_data on file release")
Reported-by: syzbot+2faa4825e556199361f9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f62d64848fc4c7c30cd6
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
clang gets a bit confused by the code in the qed_mfw_process_tlv_req and
ends up spilling registers to the stack hundreds of times. When sanitizers
are enabled, this can end up blowing the stack warning limit:
drivers/net/ethernet/qlogic/qed/qed_mng_tlv.c:1244:5: error: stack frame size (1824) exceeds limit (1280) in 'qed_mfw_process_tlv_req' [-Werror,-Wframe-larger-than]
Apparently the problem is the complexity of qed_mfw_update_tlvs()
after inlining, and marking the four main branches of that function
as noinline_for_stack makes this problem completely go away, the stack
usage goes down to 100 bytes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the hibernate entry sequence, ACP registers will be reset to
default values and acp ip will be completely powered off including acp
SoundWire pads. During resume sequence, if acp SoundWire pad keeper enable
register is not restored along with pad pulldown control register value,
then SoundWire manager links won't be powered on correctly results in
peripheral register access failures and completely audio function is
broken.
Add code to store the acp SoundWire pad keeper enable register and acp pad
pulldown ctrl register values before entering into suspend state and
restore the register values during resume sequence based on condition check
for acp SoundWire pad keeper enable register for ACP6.3, ACP7.0 & ACP7.1
platforms.
Fixes: 4916283880 ("ASoC: amd: ps: add callback functions for acp pci driver pm ops")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20250623084630.3100279-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reading DPCD registers has side-effects in general. In particular
accessing registers outside of the link training register range
(0x102-0x106, 0x202-0x207, 0x200c-0x200f, 0x2216) is explicitly
forbidden by the DP v2.1 Standard, see
3.6.5.1 DPTX AUX Transaction Handling Mandates
3.6.7.4 128b/132b DP Link Layer LTTPR Link Training Mandates
Based on my tests, accessing the DPCD_REV register during the link
training of an UHBR TBT DP tunnel sink leads to link training failures.
Solve the above by using the DP_LANE0_1_STATUS (0x202) register for the
DPCD register access quirk.
Cc: <stable@vger.kernel.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250605082850.65136-2-imre.deak@intel.com
(cherry picked from commit a40c5d727b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The drm_writeback_connector_cleanup have the signature:
static void drm_writeback_connector_cleanup(
struct drm_device *dev,
struct drm_writeback_connector *wb_connector)
But it is stored and used as a drmres_release_t
typedef void (*drmres_release_t)(struct drm_device *dev, void *res);
While the current code is valid and does not produce any warning, the
CFI runtime check (CONFIG_CFI_CLANG) can fail because the function
signature is not the same as drmres_release_t.
In order to fix this, change the function signature to match what is
expected by drmres_release_t.
Fixes: 1914ba2b91 ("drm: writeback: Create drmm variants for drm_writeback_connector initialization")
Suggested-by: Mark Yacoub <markyacoub@google.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://lore.kernel.org/r/20250429-drm-fix-writeback-cleanup-v2-1-548ff3a4e284@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
With CONFIG_SND_SOC_SM8250=y and CONFIG_SND_SOC_QCOM_OFFLOAD_UTILS=m
selected in kconfig, the build will fail due to trying to link against a
symbol only found in the module.
aarch64-linux-gnu-ld: sound/soc/qcom/sm8250.o: in function `sm8250_snd_exit':
sound/soc/qcom/sm8250.c:52:(.text+0x210): undefined reference to `qcom_snd_usb_offload_jack_remove'
Fix this by declaring the dependency that forces CONFIG_SND_SOC_SM8250=m
when CONFIG_SND_SOC_QCOM_OFFLOAD_UTILS is =m.
Reported-by: Matthew Croughan <matthew.croughan@nix.how>
Fixes: 1b8d0d87b9 ("ASoC: qcom: qdsp6: Add headphone jack for offload connection status")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://patch.msgid.link/20250617-snd-sm8250-dep-fix-v1-1-879af8906ec4@fairphone.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rst
Fixes a spelling mistake: "funcionality" → "functionality".
Signed-off-by: Faisal Bukhari <faisalbukhari523@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling bch2_indirect_extent_missing_error(), we have to
calculate the missing range, which is the intersection of the reflink
pointer and the non-indirect-extent we found.
The calculation didn't take into account that the returned extent may
span the iter position, leading to an infinite loop when we
(unnecessarily) resized the extent we were returning to one that didn't
extend past the offset we were looking up.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
When the compiler chooses to not inline sha256_choose_blocks() in
the purgatory code, it fails to link against the missing CPU
specific version:
x86_64-linux-ld: arch/x86/purgatory/purgatory.ro: in function `sha256_choose_blocks.part.0':
sha256.c:(.text+0x6a6): undefined reference to `irq_fpu_usable'
sha256.c:(.text+0x6c7): undefined reference to `sha256_blocks_arch'
sha256.c:(.text+0x6cc): undefined reference to `sha256_blocks_simd'
Mark this function as __always_inline to prevent this, same as sha256_finup().
Fixes: 5b90a779bc ("crypto: lib/sha256 - Add helpers for block-based shash")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250620191952.1867578-1-arnd@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Some modules have BT_EN enabled via a hardware pull-up,
meaning it is not defined in the DTS and is not controlled
through the power sequence. In such cases, fall through
to follow the legacy flow.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
OBEX download from iPhone is currently slow due to small packet size
used to transfer data which doesn't follow the MTU negotiated during
L2CAP connection, i.e. 672 bytes instead of 32767:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 4103 (0x1007)
Source CID: 72
> ACL Data RX: Handle 11 flags 0x02 dlen 16
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 14608
Source CID: 72
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 20 len 19
Destination CID: 14608
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 72 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 72 len 21
Source CID: 14608
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 672
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 20 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 1 ReqSeq 2
< ACL Data TX: Handle 11 flags 0x00 dlen 13
Channel: 14608 len 9 ctrl 0x0204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 680
Channel: 72 len 676 ctrl 0x0304 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Unsegmented TxSeq 2 ReqSeq 3
The MTUs are negotiated for each direction. In this traces 32767 for
iPhone->localhost and no MTU for localhost->iPhone, which based on
'4.4 L2CAP_CONFIGURATION_REQ' (Core specification v5.4, Vol. 3, Part
A):
The only parameters that should be included in the
L2CAP_CONFIGURATION_REQ packet are those that require different
values than the default or previously agreed values.
...
Any missing configuration parameters are assumed to have their
most recently explicitly or implicitly accepted values.
and '5.1 Maximum transmission unit (MTU)':
If the remote device sends a positive L2CAP_CONFIGURATION_RSP
packet it should include the actual MTU to be used on this channel
for traffic flowing into the local device.
...
The default value is 672 octets.
is set by BlueZ to 672 bytes.
It seems that the iPhone used the lowest negotiated value to transfer
data to the localhost instead of the negotiated one for the incoming
direction.
This could be fixed by using the MTU negotiated for the other
direction, if exists, in the L2CAP_CONFIGURATION_RSP.
This allows to use segmented packets as in the following traces:
< ACL Data TX: Handle 11 flags 0x00 dlen 12
L2CAP: Connection Request (0x02) ident 22 len 4
PSM: 4103 (0x1007)
Source CID: 72
< ACL Data TX: Handle 11 flags 0x00 dlen 27
L2CAP: Configure Request (0x04) ident 24 len 19
Destination CID: 2832
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 26
L2CAP: Configure Request (0x04) ident 15 len 18
Destination CID: 72
Flags: 0x0000
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 65527
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
< ACL Data TX: Handle 11 flags 0x00 dlen 29
L2CAP: Configure Response (0x05) ident 15 len 21
Source CID: 2832
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 32
Max transmit: 255
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
> ACL Data RX: Handle 11 flags 0x02 dlen 32
L2CAP: Configure Response (0x05) ident 24 len 24
Source CID: 72
Flags: 0x0000
Result: Success (0x0000)
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 32767
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Enhanced Retransmission (0x03)
TX window size: 63
Max transmit: 3
Retransmission timeout: 2000
Monitor timeout: 12000
Maximum PDU size: 1009
Option: Frame Check Sequence (0x05) [mandatory]
FCS: 16-bit FCS (0x01)
...
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0x4202 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Start (len 21884) TxSeq 1 ReqSeq 2
> ACL Data RX: Handle 11 flags 0x02 dlen 1009
Channel: 72 len 1005 ctrl 0xc204 [PSM 4103 mode Enhanced Retransmission (0x03)] {chan 8}
I-frame: Continuation TxSeq 2 ReqSeq 2
This has been tested with kernel 5.4 and BlueZ 5.77.
Cc: stable@vger.kernel.org
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During firmware download, if an error occurs, interrupts must be
disabled, synchronized, and re-enabled before retrying the download.
This change ensures proper interrupt handling to prevent race
conditions.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add "Thinkpad X1 Tablet Gen 2 Keyboard" PID to hid-lenovo driver to fix trackpoint not working issue.
Signed-off-by: Akira Inoue <niyarium@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During appletb_kbd_probe, probe attempts to get the backlight device
by name. When this happens backlight_device_get_by_name looks for a
device in the backlight class which has name "appletb_backlight" and
upon finding a match it increments the reference count for the device
and returns it to the caller. However this reference is never released
leading to a reference leak.
Fix this by decrementing the backlight device reference count on removal
via put_device and on probe failure.
Fixes: 93a0fc4894 ("HID: hid-appletb-kbd: add support for automatic brightness control while using the touchbar")
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Reviewed-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Change my role to Maintainer as I am quite involved in HugeTLB
development, and will be more so with the upcoming HugetLB-pagewalk
unification, so I would like to help Munchun take care of the code.
Besides, having two people will help in offloading some pressure.
Also add David as a Reviewer since he has quite some knowledge in the
field and has already provided valuable feedback.
Link: https://lkml.kernel.org/r/20250617185910.471406-1-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This reverts commit 866898efbb.
The generic bottom-up min_heap implementation causes performance
regression in invalidate_buckets_lru(), a hot path in bcache. Before the
cache is fully populated, new_bucket_prio() often returns zero, leading to
many equal comparisons. In such cases, bottom-up sift_down performs up to
2 * log2(n) comparisons, while the original top-down approach completes
with just O() comparisons, resulting in a measurable performance gap.
The performance degradation is further worsened by the non-inlined
min_heap API functions introduced in commit 92a8b224b8 ("lib/min_heap:
introduce non-inline versions of min heap API functions"), adding function
call overhead to this critical path.
As reported by Robert, bcache now suffers from latency spikes, with P100
(max) latency increasing from 600 ms to 2.4 seconds every 5 minutes.
These regressions degrade bcache's effectiveness as a low-latency cache
layer and lead to frequent timeouts and application stalls in production
environments.
This revert aims to restore bcache's original low-latency behavior.
Link: https://lore.kernel.org/lkml/CAJhEC05+0S69z+3+FB2Cd0hD+pCRyWTKLEOsc8BOmH73p1m+KQ@mail.gmail.com
Link: https://lkml.kernel.org/r/20250614202353.1632957-3-visitorckw@gmail.com
Fixes: 866898efbb ("bcache: remove heap-related macros and switch to generic min_heap")
Fixes: 92a8b224b8 ("lib/min_heap: introduce non-inline versions of min heap API functions")
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reported-by: Robert Pang <robertpang@google.com>
Closes: https://lore.kernel.org/linux-bcache/CAJhEC06F_AtrPgw2-7CvCqZgeStgCtitbD-ryuPpXQA-JG5XXw@mail.gmail.com
Acked-by: Coly Li <colyli@kernel.org>
Cc: Ching-Chun (Jim) Huang <jserv@ccns.ncku.edu.tw>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "bcache: Revert min_heap migration due to performance
regression".
This patch series reverts the migration of bcache from its original heap
implementation to the generic min_heap library. While the original change
aimed to simplify the code and improve maintainability, it introduced a
severe performance regression in real-world scenarios.
As reported by Robert, systems using bcache now suffer from periodic
latency spikes, with P100 (max) latency increasing from 600 ms to 2.4
seconds every 5 minutes. This degrades bcache's value as a low-latency
caching layer, and leads to frequent timeouts and application stalls in
production environments.
The primary cause of this regression is the behavior of the generic
min_heap implementation's bottom-up sift_down, which performs up to 2 *
log2(n) comparisons when many elements are equal. The original top-down
variant used by bcache only required O(1) comparisons in such cases. The
issue was further exacerbated by commit 92a8b224b8 ("lib/min_heap:
introduce non-inline versions of min heap API functions"), which
introduced non-inlined versions of the min_heap API, adding function call
overhead to a performance-critical hot path.
This patch (of 3):
This reverts commit 3d8a9a1c35.
Although removing the custom swap function simplified the code, this
change is part of a broader migration to the generic min_heap API that
introduced significant performance regressions in bcache.
As reported by Robert, bcache now suffers from latency spikes, with P100
(max) latency increasing from 600 ms to 2.4 seconds every 5 minutes.
These regressions degrade bcache's effectiveness as a low-latency cache
layer and lead to frequent timeouts and application stalls in production
environments.
This revert is part of a series of changes to restore previous performance
by undoing the min_heap transition.
Link: https://lkml.kernel.org/r/20250614202353.1632957-1-visitorckw@gmail.com
Link: https://lore.kernel.org/lkml/CAJhEC05+0S69z+3+FB2Cd0hD+pCRyWTKLEOsc8BOmH73p1m+KQ@mail.gmail.com
Link: https://lkml.kernel.org/r/20250614202353.1632957-2-visitorckw@gmail.com
Fixes: 866898efbb ("bcache: remove heap-related macros and switch to generic min_heap")
Fixes: 92a8b224b8 ("lib/min_heap: introduce non-inline versions of min heap API functions")
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reported-by: Robert Pang <robertpang@google.com>
Closes: https://lore.kernel.org/linux-bcache/CAJhEC06F_AtrPgw2-7CvCqZgeStgCtitbD-ryuPpXQA-JG5XXw@mail.gmail.com
Acked-by: Coly Li <colyli@kernel.org>
Cc: Ching-Chun (Jim) Huang <jserv@ccns.ncku.edu.tw>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If CONFIG_UPROBES is not set, a merge subtest fails:
Failure log:
7151 12:46:54.627936 # # # RUN merge.handle_uprobe_upon_merged_vma ...
7152 12:46:54.639014 # # f /sys/bus/event_source/devices/uprobe/type
7153 12:46:54.639306 # # fopen: No such file or directory
7154 12:46:54.650451 # # # merge.c:473:handle_uprobe_upon_merged_vma:Expected read_sysfs("/sys/bus/event_source/devices/uprobe/type", &type) (1) == 0 (0)
7155 12:46:54.650730 # # # handle_uprobe_upon_merged_vma: Test terminated by assertion
7156 12:46:54.661750 # # # FAIL merge.handle_uprobe_upon_merged_vma
7157 12:46:54.662030 # # not ok 8 merge.handle_uprobe_upon_merged_vma
CONFIG_UPROBES is enabled by CONFIG_UPROBE_EVENTS, which gets enabled by
CONFIG_FTRACE. Therefore add these configs to selftests/mm/config so that
CI systems can include this config in the kernel build. To be completely
safe, add CONFIG_PROFILING too, to enable the dependency chain
PROFILING -> PERF_EVENTS -> UPROBE_EVENTS -> UPROBES.
Link: https://lkml.kernel.org/r/20250613034912.53791-1-dev.jain@arm.com
Fixes: efe99fabeb ("selftests/mm: add test about uprobe pte be orphan during vma merge")
Signed-off-by: Dev Jain <dev.jain@arm.com>
Reported-by: Aishwarya <aishwarya.tcv@arm.com>
Closes: https://lore.kernel.org/all/20250610103729.72440-1-aishwarya.tcv@arm.com/
Tested-by: Aishwarya TCV <aishwarya.tcv@arm.com>
Tested-by : Donet Tom <donettom@linux.ibm.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Donet Tom <donettom@linux.ibm.com>
Reviewed-by: Pedro Falcato <pfalcato@suse.de>
Cc: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Pu Lehui <pulehui@huawei.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently, when restoring higher order folios, kho_restore_folio() only
calls prep_compound_page() on all the pages. That is not enough to
properly initialize the folios. The managed page count does not get
updated, the reserved flag does not get dropped, and page count does not
get initialized properly.
Restoring a higher order folio with it results in the following BUG with
CONFIG_DEBUG_VM when attempting to free the folio:
BUG: Bad page state in process test pfn:104e2b
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0xffffffffffffffff pfn:0x104e2b
flags: 0x2fffff80000000(node=0|zone=2|lastcpupid=0x1fffff)
raw: 002fffff80000000 0000000000000000 00000000ffffffff 0000000000000000
raw: ffffffffffffffff 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: nonzero _refcount
[...]
Call Trace:
<TASK>
dump_stack_lvl+0x4b/0x70
bad_page.cold+0x97/0xb2
__free_frozen_pages+0x616/0x850
[...]
Combine the path for 0-order and higher order folios, initialize the tail
pages with a count of zero, and call adjust_managed_page_count() to
account for all the pages instead of just missing them.
In addition, since all the KHO-preserved pages get marked with
MEMBLOCK_RSRV_NOINIT by deserialize_bitmap(), the reserved flag is not
actually set (as can also be seen from the flags of the dumped page in the
logs above). So drop the ClearPageReserved() calls.
[ptyadav@amazon.de: declare i in the loop instead of at the top]
Link: https://lkml.kernel.org/r/20250613125916.39272-1-pratyush@kernel.org
Link: https://lkml.kernel.org/r/20250605171143.76963-1-pratyush@kernel.org
Fixes: fc33e4b44b ("kexec: enable KHO support for memory preservation")
Signed-off-by: Pratyush Yadav <ptyadav@amazon.de>
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This commit fixes two kinds of races, they may have different results:
Barry reported a BUG_ON in commit c50f8e6053, we may see the same
BUG_ON if the filemap lookup returned NULL and folio is added to swap
cache after that.
If another kind of race is triggered (folio changed after lookup) we
may see RSS counter is corrupted:
[ 406.893936] BUG: Bad rss-counter state mm:ffff0000c5a9ddc0
type:MM_ANONPAGES val:-1
[ 406.894071] BUG: Bad rss-counter state mm:ffff0000c5a9ddc0
type:MM_SHMEMPAGES val:1
Because the folio is being accounted to the wrong VMA.
I'm not sure if there will be any data corruption though, seems no.
The issues above are critical already.
On seeing a swap entry PTE, userfaultfd_move does a lockless swap cache
lookup, and tries to move the found folio to the faulting vma. Currently,
it relies on checking the PTE value to ensure that the moved folio still
belongs to the src swap entry and that no new folio has been added to the
swap cache, which turns out to be unreliable.
While working and reviewing the swap table series with Barry, following
existing races are observed and reproduced [1]:
In the example below, move_pages_pte is moving src_pte to dst_pte, where
src_pte is a swap entry PTE holding swap entry S1, and S1 is not in the
swap cache:
CPU1 CPU2
userfaultfd_move
move_pages_pte()
entry = pte_to_swp_entry(orig_src_pte);
// Here it got entry = S1
... < interrupted> ...
<swapin src_pte, alloc and use folio A>
// folio A is a new allocated folio
// and get installed into src_pte
<frees swap entry S1>
// src_pte now points to folio A, S1
// has swap count == 0, it can be freed
// by folio_swap_swap or swap
// allocator's reclaim.
<try to swap out another folio B>
// folio B is a folio in another VMA.
<put folio B to swap cache using S1 >
// S1 is freed, folio B can use it
// for swap out with no problem.
...
folio = filemap_get_folio(S1)
// Got folio B here !!!
... < interrupted again> ...
<swapin folio B and free S1>
// Now S1 is free to be used again.
<swapout src_pte & folio A using S1>
// Now src_pte is a swap entry PTE
// holding S1 again.
folio_trylock(folio)
move_swap_pte
double_pt_lock
is_pte_pages_stable
// Check passed because src_pte == S1
folio_move_anon_rmap(...)
// Moved invalid folio B here !!!
The race window is very short and requires multiple collisions of multiple
rare events, so it's very unlikely to happen, but with a deliberately
constructed reproducer and increased time window, it can be reproduced
easily.
This can be fixed by checking if the folio returned by filemap is the
valid swap cache folio after acquiring the folio lock.
Another similar race is possible: filemap_get_folio may return NULL, but
folio (A) could be swapped in and then swapped out again using the same
swap entry after the lookup. In such a case, folio (A) may remain in the
swap cache, so it must be moved too:
CPU1 CPU2
userfaultfd_move
move_pages_pte()
entry = pte_to_swp_entry(orig_src_pte);
// Here it got entry = S1, and S1 is not in swap cache
folio = filemap_get_folio(S1)
// Got NULL
... < interrupted again> ...
<swapin folio A and free S1>
<swapout folio A re-using S1>
move_swap_pte
double_pt_lock
is_pte_pages_stable
// Check passed because src_pte == S1
folio_move_anon_rmap(...)
// folio A is ignored !!!
Fix this by checking the swap cache again after acquiring the src_pte
lock. And to avoid the filemap overhead, we check swap_map directly [2].
The SWP_SYNCHRONOUS_IO path does make the problem more complex, but so far
we don't need to worry about that, since folios can only be exposed to the
swap cache in the swap out path, and this is covered in this patch by
checking the swap cache again after acquiring the src_pte lock.
Testing with a simple C program that allocates and moves several GB of
memory did not show any observable performance change.
Link: https://lkml.kernel.org/r/20250604151038.21968-1-ryncsn@gmail.com
Fixes: adef440691 ("userfaultfd: UFFDIO_MOVE uABI")
Signed-off-by: Kairui Song <kasong@tencent.com>
Closes: https://lore.kernel.org/linux-mm/CAMgjq7B1K=6OOrK2OUZ0-tqCzi+EJt+2_K97TPGoSt=9+JwP7Q@mail.gmail.com/ [1]
Link: https://lore.kernel.org/all/CAGsJ_4yJhJBo16XhiC-nUzSheyX-V3-nFE+tAi=8Y560K8eT=A@mail.gmail.com/ [2]
Reviewed-by: Lokesh Gidra <lokeshgidra@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Barry Song <baohua@kernel.org>
Reviewed-by: Chris Li <chrisl@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Kairui Song <kasong@tencent.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
After commit 1aaf8c1229 ("mm: gup: fix infinite loop within
__get_longterm_locked") we are able to longterm pin folios that are not
supposed to get longterm pinned, simply because they temporarily have the
LRU flag cleared (esp. temporarily isolated).
For example, two __get_longterm_locked() callers can race, or
__get_longterm_locked() can race with anything else that temporarily
isolates folios.
The introducing commit mentions the use case of a driver that uses
vm_ops->fault to insert pages allocated through cma_alloc() into the page
tables, assuming they can later get longterm pinned. These pages/ folios
would never have the LRU flag set and consequently cannot get isolated.
There is no known in-tree user making use of that so far, fortunately.
To handle that in the future -- and avoid retrying forever to
isolate/migrate them -- we will need a different mechanism for the CMA
area *owner* to indicate that it actually already allocated the page and
is fine with longterm pinning it. The LRU flag is not suitable for that.
Probably we can lookup the relevant CMA area and query the bitmap; we only
have have to care about some races, probably. If already allocated, we
could just allow longterm pinning)
Anyhow, let's fix the "must not be longterm pinned" problem first by
reverting the original commit.
Link: https://lkml.kernel.org/r/20250611131314.594529-1-david@redhat.com
Fixes: 1aaf8c1229 ("mm: gup: fix infinite loop within __get_longterm_locked")
Signed-off-by: David Hildenbrand <david@redhat.com>
Closes: https://lore.kernel.org/all/20250522092755.GA3277597@tiffany/
Reported-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Peter Xu <peterx@redhat.com>
Cc: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Cc: Aijun Sun <aijun.sun@unisoc.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When both the RHBA and RPA FDMI requests time out, fnic reuses a frame to
send ABTS for each of them. On send completion, this causes an attempt to
free the same frame twice that leads to a crash.
Fix crash by allocating separate frames for RHBA and RPA, and modify ABTS
logic accordingly.
Tested by checking MDS for FDMI information.
Tested by using instrumented driver to:
- Drop PLOGI response
- Drop RHBA response
- Drop RPA response
- Drop RHBA and RPA response
- Drop PLOGI response + ABTS response
- Drop RHBA response + ABTS response
- Drop RPA response + ABTS response
- Drop RHBA and RPA response + ABTS response for both of them
Fixes: 09c1e6ab4a ("scsi: fnic: Add and integrate support for FDMI")
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Reviewed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Tested-by: Arun Easi <aeasi@cisco.com>
Co-developed-by: Arun Easi <aeasi@cisco.com>
Signed-off-by: Arun Easi <aeasi@cisco.com>
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20250618003431.6314-1-kartilak@cisco.com
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On a system with DRAM interleave enabled, out-of-bound access is
detected:
megaraid_sas 0000:3f:00.0: requested/available msix 128/128 poll_queue 0
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in ./arch/x86/include/asm/topology.h:72:28
index -1 is out of range for type 'cpumask *[1024]'
dump_stack_lvl+0x5d/0x80
ubsan_epilogue+0x5/0x2b
__ubsan_handle_out_of_bounds.cold+0x46/0x4b
megasas_alloc_irq_vectors+0x149/0x190 [megaraid_sas]
megasas_probe_one.cold+0xa4d/0x189c [megaraid_sas]
local_pci_probe+0x42/0x90
pci_device_probe+0xdc/0x290
really_probe+0xdb/0x340
__driver_probe_device+0x78/0x110
driver_probe_device+0x1f/0xa0
__driver_attach+0xba/0x1c0
bus_for_each_dev+0x8b/0xe0
bus_add_driver+0x142/0x220
driver_register+0x72/0xd0
megasas_init+0xdf/0xff0 [megaraid_sas]
do_one_initcall+0x57/0x310
do_init_module+0x90/0x250
init_module_from_file+0x85/0xc0
idempotent_init_module+0x114/0x310
__x64_sys_finit_module+0x65/0xc0
do_syscall_64+0x82/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fix it accordingly.
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Link: https://lore.kernel.org/r/20250604042556.3731059-1-yu.c.chen@intel.com
Fixes: 8049da6f39 ("scsi: megaraid_sas: Use irq_set_affinity_and_hint()")
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MANA supports RDMA in PF mode. The driver should record the doorbell
physical address when in PF mode.
The doorbell physical address is used by the RDMA driver to map
doorbell pages of the device to user-mode applications through RDMA
verbs interface. In the past, they have been mapped to user-mode while
the device is in VF mode. With the support for PF mode implemented,
also expose those pages in PF mode.
Support for PF mode is implemented in
290e5d3c49 ("net: mana: Add support for Multi Vports on Bare metal")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1750210606-12167-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the end result of a security_compute_sid() computation matches the
ssid or tsid, return that SID rather than looking it up again. This
avoids the problem of multiple initial SIDs that map to the same
context.
Cc: stable@vger.kernel.org
Reported-by: Guido Trentalancia <guido@trentalancia.com>
Fixes: ae254858ce ("selinux: introduce an initial SID for early boot processes")
Signed-off-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Tested-by: Guido Trentalancia <guido@trentalancia.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
This fixes exceeding the bump allocator limit when the allocator finds
many buckets that need repair - they're repaired asynchronously, which
means that every error logged a message in the bump allocator, without
committing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Don't change buf->size on error - this would usually be a transaction
restart, but it could also be -ENOMEM - when we've exceeded the bump
allocator max).
Fixes: 247abee6ae ("bcachefs: btree_trans_subbuf")
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
After commit 6f110a5e4f ("Disable SLUB_TINY for build testing"), which
causes CONFIG_KASAN to be enabled in allmodconfig again, arm64
allmodconfig builds with older versions of clang (15 through 17) show an
instance of -Wframe-larger-than (which breaks the build with
CONFIG_WERROR=y):
drivers/staging/rtl8723bs/core/rtw_security.c:1287:5: error: stack frame size (2208) exceeds limit (2048) in 'rtw_aes_decrypt' [-Werror,-Wframe-larger-than]
1287 | u32 rtw_aes_decrypt(struct adapter *padapter, u8 *precvframe)
| ^
This comes from aes_decipher() being inlined in rtw_aes_decrypt().
Running the same build with CONFIG_FRAME_WARN=128 shows aes_cipher()
also uses a decent amount of stack, just under the limit of 2048:
drivers/staging/rtl8723bs/core/rtw_security.c:864:19: warning: stack frame size (1952) exceeds limit (128) in 'aes_cipher' [-Wframe-larger-than]
864 | static signed int aes_cipher(u8 *key, uint hdrlen,
| ^
-Rpass-analysis=stack-frame-layout only shows one large structure on the
stack, which is the ctx variable inlined from aes128k128d(). A good
number of the other variables come from the additional checks of
fortified string routines, which are present in memset(), which both
aes_cipher() and aes_decipher() use to initialize some temporary
buffers. In this case, since the size is known at compile time, these
additional checks should not result in any code generation changes but
allmodconfig has several sanitizers enabled, which may make it harder
for the compiler to eliminate the compile time checks and the variables
that come about from them.
The memset() calls are just initializing these buffers to zero, so use
'= {}' instead, which is used all over the kernel and does the exact
same thing as memset() without the fortify checks, which drops the stack
usage of these functions by a few hundred kilobytes.
drivers/staging/rtl8723bs/core/rtw_security.c:864:19: warning: stack frame size (1584) exceeds limit (128) in 'aes_cipher' [-Wframe-larger-than]
864 | static signed int aes_cipher(u8 *key, uint hdrlen,
| ^
drivers/staging/rtl8723bs/core/rtw_security.c:1271:5: warning: stack frame size (1456) exceeds limit (128) in 'rtw_aes_decrypt' [-Wframe-larger-than]
1271 | u32 rtw_aes_decrypt(struct adapter *padapter, u8 *precvframe)
| ^
Cc: stable@vger.kernel.org
Fixes: 554c0a3abf ("staging: Add rtl8723bs sdio wifi driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20250609-rtl8723bs-fix-clang-arm64-wflt-v1-1-e2accba43def@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When one of two zones composing a DUP block group is a conventional zone,
we have the zone_info[i]->alloc_offset = WP_CONVENTIONAL. That will, of
course, not match the write pointer of the other zone, and fails that
block group.
This commit solves that issue by properly recovering the emulated write
pointer from the last allocated extent. The offset for the SINGLE, DUP,
and RAID1 are straight-forward: it is same as the end of last allocated
extent. The RAID0 and RAID10 are a bit tricky that we need to do the math
of striping.
This is the kernel equivalent of Naohiro's user-space commit:
"btrfs-progs: zoned: fix alloc_offset calculation for partly
conventional block groups".
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
There is syzbot based reproducer that can crash the kernel, with the
following call trace: (With some debug output added)
DEBUG: rescue=ibadroots parsed
BTRFS: device fsid 14d642db-7b15-43e4-81e6-4b8fac6a25f8 devid 1 transid 8 /dev/loop0 (7:0) scanned by repro (1010)
BTRFS info (device loop0): first mount of filesystem 14d642db-7b15-43e4-81e6-4b8fac6a25f8
BTRFS info (device loop0): using blake2b (blake2b-256-generic) checksum algorithm
BTRFS info (device loop0): using free-space-tree
BTRFS warning (device loop0): checksum verify failed on logical 5312512 mirror 1 wanted 0xb043382657aede36608fd3386d6b001692ff406164733d94e2d9a180412c6003 found 0x810ceb2bacb7f0f9eb2bf3b2b15c02af867cb35ad450898169f3b1f0bd818651 level 0
DEBUG: read tree root path failed for tree csum, ret=-5
BTRFS warning (device loop0): checksum verify failed on logical 5328896 mirror 1 wanted 0x51be4e8b303da58e6340226815b70e3a93592dac3f30dd510c7517454de8567a found 0x51be4e8b303da58e634022a315b70e3a93592dac3f30dd510c7517454de8567a level 0
BTRFS warning (device loop0): checksum verify failed on logical 5292032 mirror 1 wanted 0x1924ccd683be9efc2fa98582ef58760e3848e9043db8649ee382681e220cdee4 found 0x0cb6184f6e8799d9f8cb335dccd1d1832da1071d12290dab3b85b587ecacca6e level 0
process 'repro' launched './file2' with NULL argv: empty string added
DEBUG: no csum root, idatacsums=0 ibadroots=134217728
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000041: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000208-0x000000000000020f]
CPU: 5 UID: 0 PID: 1010 Comm: repro Tainted: G OE 6.15.0-custom+ #249 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:btrfs_lookup_csum+0x93/0x3d0 [btrfs]
Call Trace:
<TASK>
btrfs_lookup_bio_sums+0x47a/0xdf0 [btrfs]
btrfs_submit_bbio+0x43e/0x1a80 [btrfs]
submit_one_bio+0xde/0x160 [btrfs]
btrfs_readahead+0x498/0x6a0 [btrfs]
read_pages+0x1c3/0xb20
page_cache_ra_order+0x4b5/0xc20
filemap_get_pages+0x2d3/0x19e0
filemap_read+0x314/0xde0
__kernel_read+0x35b/0x900
bprm_execve+0x62e/0x1140
do_execveat_common.isra.0+0x3fc/0x520
__x64_sys_execveat+0xdc/0x130
do_syscall_64+0x54/0x1d0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
---[ end trace 0000000000000000 ]---
[CAUSE]
Firstly the fs has a corrupted csum tree root, thus to mount the fs we
have to go "ro,rescue=ibadroots" mount option.
Normally with that mount option, a bad csum tree root should set
BTRFS_FS_STATE_NO_DATA_CSUMS flag, so that any future data read will
ignore csum search.
But in this particular case, we have the following call trace that
caused NULL csum root, but not setting BTRFS_FS_STATE_NO_DATA_CSUMS:
load_global_roots_objectid():
ret = btrfs_search_slot();
/* Succeeded */
btrfs_item_key_to_cpu()
found = true;
/* We found the root item for csum tree. */
root = read_tree_root_path();
if (IS_ERR(root)) {
if (!btrfs_test_opt(fs_info, IGNOREBADROOTS))
/*
* Since we have rescue=ibadroots mount option,
* @ret is still 0.
*/
break;
if (!found || ret) {
/* @found is true, @ret is 0, error handling for csum
* tree is skipped.
*/
}
This means we completely skipped to set BTRFS_FS_STATE_NO_DATA_CSUMS if
the csum tree is corrupted, which results unexpected later csum lookup.
[FIX]
If read_tree_root_path() failed, always populate @ret to the error
number.
As at the end of the function, we need @ret to determine if we need to
do the extra error handling for csum tree.
Fixes: abed4aaae4 ("btrfs: track the csum, extent, and free space trees in a rb tree")
Reported-by: Zhiyu Zhang <zhiyuzhang999@gmail.com>
Reported-by: Longxing Li <coregee2000@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Syzbot reported an assertion failure due to an attempt to add a delayed
iput after we have set BTRFS_FS_STATE_NO_DELAYED_IPUT in the fs_info
state:
WARNING: CPU: 0 PID: 65 at fs/btrfs/inode.c:3420 btrfs_add_delayed_iput+0x2f8/0x370 fs/btrfs/inode.c:3420
Modules linked in:
CPU: 0 UID: 0 PID: 65 Comm: kworker/u8:4 Not tainted 6.15.0-next-20250530-syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Workqueue: btrfs-endio-write btrfs_work_helper
RIP: 0010:btrfs_add_delayed_iput+0x2f8/0x370 fs/btrfs/inode.c:3420
Code: 4e ad 5d (...)
RSP: 0018:ffffc9000213f780 EFLAGS: 00010293
RAX: ffffffff83c635b7 RBX: ffff888058920000 RCX: ffff88801c769e00
RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000000
RBP: 0000000000000001 R08: ffff888058921b67 R09: 1ffff1100b12436c
R10: dffffc0000000000 R11: ffffed100b12436d R12: 0000000000000001
R13: dffffc0000000000 R14: ffff88807d748000 R15: 0000000000000100
FS: 0000000000000000(0000) GS:ffff888125c53000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00002000000bd038 CR3: 000000006a142000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
btrfs_put_ordered_extent+0x19f/0x470 fs/btrfs/ordered-data.c:635
btrfs_finish_one_ordered+0x11d8/0x1b10 fs/btrfs/inode.c:3312
btrfs_work_helper+0x399/0xc20 fs/btrfs/async-thread.c:312
process_one_work kernel/workqueue.c:3238 [inline]
process_scheduled_works+0xae1/0x17b0 kernel/workqueue.c:3321
worker_thread+0x8a0/0xda0 kernel/workqueue.c:3402
kthread+0x70e/0x8a0 kernel/kthread.c:464
ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
This can happen due to a race with the async reclaim worker like this:
1) The async metadata reclaim worker enters shrink_delalloc(), which calls
btrfs_start_delalloc_roots() with an nr_pages argument that has a value
less than LONG_MAX, and that in turn enters start_delalloc_inodes(),
which sets the local variable 'full_flush' to false because
wbc->nr_to_write is less than LONG_MAX;
2) There it finds inode X in a root's delalloc list, grabs a reference for
inode X (with igrab()), and triggers writeback for it with
filemap_fdatawrite_wbc(), which creates an ordered extent for inode X;
3) The unmount sequence starts from another task, we enter close_ctree()
and we flush the workqueue fs_info->endio_write_workers, which waits
for the ordered extent for inode X to complete and when dropping the
last reference of the ordered extent, with btrfs_put_ordered_extent(),
when we call btrfs_add_delayed_iput() we don't add the inode to the
list of delayed iputs because it has a refcount of 2, so we decrement
it to 1 and return;
4) Shortly after at close_ctree() we call btrfs_run_delayed_iputs() which
runs all delayed iputs, and then we set BTRFS_FS_STATE_NO_DELAYED_IPUT
in the fs_info state;
5) The async reclaim worker, after calling filemap_fdatawrite_wbc(), now
calls btrfs_add_delayed_iput() for inode X and there we trigger an
assertion failure since the fs_info state has the flag
BTRFS_FS_STATE_NO_DELAYED_IPUT set.
Fix this by setting BTRFS_FS_STATE_NO_DELAYED_IPUT only after we wait for
the async reclaim workers to finish, after we call cancel_work_sync() for
them at close_ctree(), and by running delayed iputs after wait for the
reclaim workers to finish and before setting the bit.
This race was recently introduced by commit 19e60b2a95 ("btrfs: add
extra warning if delayed iput is added when it's not allowed"). Without
the new validation at btrfs_add_delayed_iput(), this described scenario
was safe because close_ctree() later calls btrfs_commit_super(). That
will run any final delayed iputs added by reclaim workers in the window
between the btrfs_run_delayed_iputs() and the the reclaim workers being
shut down.
Reported-by: syzbot+0ed30ad435bf6f5b7a42@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/6840481c.a00a0220.d4325.000c.GAE@google.com/T/#u
Fixes: 19e60b2a95 ("btrfs: add extra warning if delayed iput is added when it's not allowed")
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When building the free space tree with the block group tree feature
enabled, we can hit an assertion failure like this:
BTRFS info (device loop0 state M): rebuilding free space tree
assertion failed: ret == 0, in fs/btrfs/free-space-tree.c:1102
------------[ cut here ]------------
kernel BUG at fs/btrfs/free-space-tree.c:1102!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Modules linked in:
CPU: 1 UID: 0 PID: 6592 Comm: syz-executor322 Not tainted 6.15.0-rc7-syzkaller-gd7fa1af5b33e #0 PREEMPT
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102
lr : populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102
sp : ffff8000a4ce7600
x29: ffff8000a4ce76e0 x28: ffff0000c9bc6000 x27: ffff0000ddfff3d8
x26: ffff0000ddfff378 x25: dfff800000000000 x24: 0000000000000001
x23: ffff8000a4ce7660 x22: ffff70001499cecc x21: ffff0000e1d8c160
x20: ffff0000e1cb7800 x19: ffff0000e1d8c0b0 x18: 00000000ffffffff
x17: ffff800092f39000 x16: ffff80008ad27e48 x15: ffff700011e740c0
x14: 1ffff00011e740c0 x13: 0000000000000004 x12: ffffffffffffffff
x11: ffff700011e740c0 x10: 0000000000ff0100 x9 : 94ef24f55d2dbc00
x8 : 94ef24f55d2dbc00 x7 : 0000000000000001 x6 : 0000000000000001
x5 : ffff8000a4ce6f98 x4 : ffff80008f415ba0 x3 : ffff800080548ef0
x2 : 0000000000000000 x1 : 0000000100000000 x0 : 000000000000003e
Call trace:
populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102 (P)
btrfs_rebuild_free_space_tree+0x14c/0x54c fs/btrfs/free-space-tree.c:1337
btrfs_start_pre_rw_mount+0xa78/0xe10 fs/btrfs/disk-io.c:3074
btrfs_remount_rw fs/btrfs/super.c:1319 [inline]
btrfs_reconfigure+0x828/0x2418 fs/btrfs/super.c:1543
reconfigure_super+0x1d4/0x6f0 fs/super.c:1083
do_remount fs/namespace.c:3365 [inline]
path_mount+0xb34/0xde0 fs/namespace.c:4200
do_mount fs/namespace.c:4221 [inline]
__do_sys_mount fs/namespace.c:4432 [inline]
__se_sys_mount fs/namespace.c:4409 [inline]
__arm64_sys_mount+0x3e8/0x468 fs/namespace.c:4409
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767
el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600
Code: f0047182 91178042 528089c3 9771d47b (d4210000)
---[ end trace 0000000000000000 ]---
This happens because we are processing an empty block group, which has
no extents allocated from it, there are no items for this block group,
including the block group item since block group items are stored in a
dedicated tree when using the block group tree feature. It also means
this is the block group with the highest start offset, so there are no
higher keys in the extent root, hence btrfs_search_slot_for_read()
returns 1 (no higher key found).
Fix this by asserting 'ret' is 0 only if the block group tree feature
is not enabled, in which case we should find a block group item for
the block group since it's stored in the extent root and block group
item keys are greater than extent item keys (the value for
BTRFS_BLOCK_GROUP_ITEM_KEY is 192 and for BTRFS_EXTENT_ITEM_KEY and
BTRFS_METADATA_ITEM_KEY the values are 168 and 169 respectively).
In case 'ret' is 1, we just need to add a record to the free space
tree which spans the whole block group, and we can achieve this by
making 'ret == 0' as the while loop's condition.
Reported-by: syzbot+36fae25c35159a763a2a@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/6841dca8.a00a0220.d4325.0020.GAE@google.com/
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If there's an unexpected (invalid) extent type, we just silently ignore
it. This means a corruption or some bug somewhere, so instead return
-EUCLEAN to the caller, making log replay fail, and print an error message
with relevant information.
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In a few places where we call read_one_inode(), if we get a NULL pointer
we end up jumping into an error path, or fallthrough in case of
__add_inode_ref(), where we then do something like this:
iput(&inode->vfs_inode);
which results in an invalid inode pointer that triggers an invalid memory
access, resulting in a crash.
Fix this by making sure we don't do such dereferences.
Fixes: b4c50cbb01 ("btrfs: return a btrfs_inode from read_one_inode()")
CC: stable@vger.kernel.org # 6.15+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we break out of the loop because an extent buffer doesn't have the bit
EXTENT_BUFFER_TREE_REF set, we end up unlocking the xarray twice, once
before we tested for the bit and break out of the loop, and once again
after the loop.
Fix this by testing the bit and exiting before unlocking the xarray.
The time spent testing the bit is negligible and it's not worth trying
to do that outside the critical section delimited by the xarray lock due
to the code complexity required to avoid it (like using a local boolean
variable to track whether the xarray is locked or not). The xarray unlock
only needs to be done before calling release_extent_buffer(), as that
needs to lock the xarray (through xa_cmpxchg_irq()) and does a more
significant amount of work.
Fixes: 19d7f65f03 ("btrfs: convert the buffer_radix to an xarray")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/linux-btrfs/aDRNDU0GM1_D4Xnw@stanley.mountain/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Each superblock contains a copy of the device item for that device. In a
transaction which drops a chunk but doesn't create any new ones, we were
correctly updating the device item in the chunk tree but not copying
over the new bytes_used value to the superblock.
This can be seen by doing the following:
# dd if=/dev/zero of=test bs=4096 count=2621440
# mkfs.btrfs test
# mount test /root/temp
# cd /root/temp
# for i in {00..10}; do dd if=/dev/zero of=$i bs=4096 count=32768; done
# sync
# rm *
# sync
# btrfs balance start -dusage=0 .
# sync
# cd
# umount /root/temp
# btrfs check test
For btrfs-check to detect this, you will also need my patch at
https://github.com/kdave/btrfs-progs/pull/991.
Change btrfs_remove_dev_extents() so that it adds the devices to the
fs_info->post_commit_list if they're not there already. This causes
btrfs_commit_device_sizes() to be called, which updates the bytes_used
value in the superblock.
Fixes: bbbf7243d6 ("btrfs: combine device update operations during transaction commit")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Mark Harmstone <maharmstone@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We have a race between a rename and directory inode logging that if it
happens and we crash/power fail before the rename completes, the next time
the filesystem is mounted, the log replay code will end up deleting the
file that was being renamed.
This is best explained following a step by step analysis of an interleaving
of steps that lead into this situation.
Consider the initial conditions:
1) We are at transaction N;
2) We have directories A and B created in a past transaction (< N);
3) We have inode X corresponding to a file that has 2 hardlinks, one in
directory A and the other in directory B, so we'll name them as
"A/foo_link1" and "B/foo_link2". Both hard links were persisted in a
past transaction (< N);
4) We have inode Y corresponding to a file that as a single hard link and
is located in directory A, we'll name it as "A/bar". This file was also
persisted in a past transaction (< N).
The steps leading to a file loss are the following and for all of them we
are under transaction N:
1) Link "A/foo_link1" is removed, so inode's X last_unlink_trans field
is updated to N, through btrfs_unlink() -> btrfs_record_unlink_dir();
2) Task A starts a rename for inode Y, with the goal of renaming from
"A/bar" to "A/baz", so we enter btrfs_rename();
3) Task A inserts the new BTRFS_INODE_REF_KEY for inode Y by calling
btrfs_insert_inode_ref();
4) Because the rename happens in the same directory, we don't set the
last_unlink_trans field of directoty A's inode to the current
transaction id, that is, we don't cal btrfs_record_unlink_dir();
5) Task A then removes the entries from directory A (BTRFS_DIR_ITEM_KEY
and BTRFS_DIR_INDEX_KEY items) when calling __btrfs_unlink_inode()
(actually the dir index item is added as a delayed item, but the
effect is the same);
6) Now before task A adds the new entry "A/baz" to directory A by
calling btrfs_add_link(), another task, task B is logging inode X;
7) Task B starts a fsync of inode X and after logging inode X, at
btrfs_log_inode_parent() it calls btrfs_log_all_parents(), since
inode X has a last_unlink_trans value of N, set at in step 1;
8) At btrfs_log_all_parents() we search for all parent directories of
inode X using the commit root, so we find directories A and B and log
them. Bu when logging direct A, we don't have a dir index item for
inode Y anymore, neither the old name "A/bar" nor for the new name
"A/baz" since the rename has deleted the old name but has not yet
inserted the new name - task A hasn't called yet btrfs_add_link() to
do that.
Note that logging directory A doesn't fallback to a transaction
commit because its last_unlink_trans has a lower value than the
current transaction's id (see step 4);
9) Task B finishes logging directories A and B and gets back to
btrfs_sync_file() where it calls btrfs_sync_log() to persist the log
tree;
10) Task B successfully persisted the log tree, btrfs_sync_log() completed
with success, and a power failure happened.
We have a log tree without any directory entry for inode Y, so the
log replay code deletes the entry for inode Y, name "A/bar", from the
subvolume tree since it doesn't exist in the log tree and the log
tree is authorative for its index (we logged a BTRFS_DIR_LOG_INDEX_KEY
item that covers the index range for the dentry that corresponds to
"A/bar").
Since there's no other hard link for inode Y and the log replay code
deletes the name "A/bar", the file is lost.
The issue wouldn't happen if task B synced the log only after task A
called btrfs_log_new_name(), which would update the log with the new name
for inode Y ("A/bar").
Fix this by pinning the log root during renames before removing the old
directory entry, and unpinning after btrfs_log_new_name() is called.
Fixes: 259c4b96d7 ("btrfs: stop doing unnecessary log updates during a rename")
CC: stable@vger.kernel.org # 5.18+
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a "scrub: " prefix to all messages logged by scrub so that it's
easy to filter them from dmesg for analysis.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a warning for leaked delayed_nodes when putting a root. We currently
do this for inodes, but not delayed_nodes.
Signed-off-by: Leo Martins <loemra.dev@gmail.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
[ Remove the changelog from the commit message. ]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If the delayed_root is not empty we are increasing the number of
references to a delayed_node without decreasing it, causing a leak. Fix
by decrementing the delayed_node reference count.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Leo Martins <loemra.dev@gmail.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
[ Remove the changelog from the commit message. ]
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
To help debugging include the root number in the error message, and since
this is a critical error that implies a metadata inconsistency and results
in a transaction abort change the log message level from "info" to
"critical", which is a much better fit.
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since in v6.8-rc1, the of_node symlink under tty devices is
missing. This breaks any udev rules relying on this information.
Link the of_node information in the serial controller device with the
parent defined in the device tree. This will also apply to the serial
device which takes the serial controller as a parent device.
Fixes: b286f4e87e ("serial: core: Move tty and serdev to be children of serial core port device")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan Stewart <astewart@tektelic.com>
Link: https://lore.kernel.org/r/20250617164819.13912-1-astewart@tektelic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BPF_MAP_TYPE_LRU_HASH can recycle most recent elements well before the
map is full, due to percpu reservations and force shrink before
neighbor stealing. Once a CPU is unable to borrow from the global map,
it will once steal one elem from a neighbor and after that each time
flush this one element to the global list and immediately recycle it.
Batch value LOCAL_FREE_TARGET (128) will exhaust a 10K element map
with 79 CPUs. CPU 79 will observe this behavior even while its
neighbors hold 78 * 127 + 1 * 15 == 9921 free elements (99%).
CPUs need not be active concurrently. The issue can appear with
affinity migration, e.g., irqbalance. Each CPU can reserve and then
hold onto its 128 elements indefinitely.
Avoid global list exhaustion by limiting aggregate percpu caches to
half of map size, by adjusting LOCAL_FREE_TARGET based on cpu count.
This change has no effect on sufficiently large tables.
Similar to LOCAL_NR_SCANS and lru->nr_scans, introduce a map variable
lru->free_target. The extra field fits in a hole in struct bpf_lru.
The cacheline is already warm where read in the hot path. The field is
only accessed with the lru lock held.
Tested-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://lore.kernel.org/r/20250618215803.3587312-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
fstest reports a f2fs bug:
generic/363 42s ... [failed, exit status 1]- output mismatch (see /share/git/fstests/results//generic/363.out.bad)
--- tests/generic/363.out 2025-01-12 21:57:40.271440542 +0800
+++ /share/git/fstests/results//generic/363.out.bad 2025-05-19 19:55:58.000000000 +0800
@@ -1,2 +1,78 @@
QA output created by 363
fsx -q -S 0 -e 1 -N 100000
+READ BAD DATA: offset = 0xd6fb, size = 0xf044, fname = /mnt/f2fs/junk
+OFFSET GOOD BAD RANGE
+0x1540d 0x0000 0x2a25 0x0
+operation# (mod 256) for the bad data may be 37
+0x1540e 0x0000 0x2527 0x1
...
(Run 'diff -u /share/git/fstests/tests/generic/363.out /share/git/fstests/results//generic/363.out.bad' to see the entire diff)
Ran: generic/363
Failures: generic/363
Failed 1 of 1 tests
The root cause is user can update post-eof page via mmap [1], however, f2fs
missed to zero post-eof page in below operations, so, once it expands i_size,
then it will include dummy data locates previous post-eof page, so during
below operations, we need to zero post-eof page.
Operations which can include dummy data after previous i_size after expanding
i_size:
- write
- mapwrite [1]
- truncate
- fallocate
* preallocate
* zero_range
* insert_range
* collapse_range
- clone_range (doesn’t support in f2fs)
- copy_range (doesn’t support in f2fs)
[1] https://man7.org/linux/man-pages/man2/mmap.2.html 'BUG section'
Cc: stable@kernel.org
Signed-off-by: Chao Yu <chao@kernel.org>
Reviewed-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The normal fsck code doesn't call key_visible_in_snapshot() with an
empty list of snapshot IDs seen (the current snapshot ID will always be
on the list), but str_hash_repair_key() ->
bch2_get_snapshot_overwrites() can, and that's totally fine as long as
we check for it.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
check_directory_structure runs after check_dirents, so it expects that
it won't see any inodes with missing backpointers - normally.
But online fsck can't run check_dirents yet, or the user might only be
running a specific pass, so we need to be careful that this isn't an
error. If an inode is unreachable, that's handled by a separate pass.
Also, add a new 'bch2_inode_has_backpointer()' helper, since we were
doing this inconsistently.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The recent change which added READ_ONCE_NOCHECK() to read the nth entry
from the kernel stack incorrectly dropped dereferencing of the stack
pointer in order to read the requested entry.
In result the address of the entry is returned instead of its content.
Dereference the pointer again to fix this.
Reported-by: Will Deacon <will@kernel.org>
Closes: https://lore.kernel.org/r/20250612163331.GA13384@willie-the-truck
Fixes: d93a855c31 ("s390/ptrace: Avoid KASAN false positives in regs_get_kernel_stack_nth()")
Cc: stable@vger.kernel.org
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
btree node scrub was sometimes failing to rewrite nodes with errors;
bch2_btree_node_rewrite() can return a transaction restart and we
weren't checking - the lockrestart_do() needs to wrap the entire
operation.
And there's a better helper it should've been using,
bch2_btree_node_rewrite_key(), which makes all this more convenient.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
LSM hooks such as security_path_mknod() and security_inode_rename() have
access to newly allocated negative dentry, which has NULL d_inode.
Therefore, it is necessary to do the NULL pointer check for d_inode.
Also add selftests that checks the verifier enforces the NULL pointer
check.
Signed-off-by: Song Liu <song@kernel.org>
Reviewed-by: Matt Bobrowski <mattbobrowski@google.com>
Link: https://lore.kernel.org/r/20250613052857.1992233-1-song@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We can only pass negative error codes to bch2_err_str(); if it's a
positive integer it's not an error and we trip an assert.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
A path exists in a particular snapshot: we should do the pathwalk in the
snapshot ID of the inode we started from, _not_ change snapshot ID as we
walk inodes and dirents.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
When we find a directory connectivity problem, we should do the repair
in the oldest snapshot that has the issue - so that we don't end up
duplicating work or making a real mess of things.
Oldest snapshot IDs have the highest integer value, so - just walk
inodes in reverse order.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
bch_subvolume.fs_path_parent needs to be updated as well, it should
match inode.bi_parent_subvol.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The bch2_subvolume_get_snapshot() call needs to happen before the dirent
lookup - the dirent is in the parent subvolume.
Also, check for loops.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
kthread creation checks for pending signals, which is _very_ annoying if
we have to do a long recovery and don't go rw until we've done
significant work.
Check if we'll be going rw and pre-allocate kthreads/workqueues.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Print out more info when we find a key (extent, dirent, xattr) for a
missing inode - was there a good inode in an older snapshot, full(ish)
list of keys for that missing inode, so we can make better decisions on
how to repair.
If it looks like it should've been deleted, autofix it. If we ever hit
the non-autofix cases, we'll want to write more repair code (possibly
reconstituting the inode).
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
After cd3cdb1ef7 ("Single err message for btree node reads"),
all errors caused __btree_err to return -BCH_ERR_fsck_fix no matter what
the actual error type was if the recovery pass was scanning for btree
nodes. This lead to the code continuing despite things like bad node
formats when they earlier would have caused a jump to fsck_err, because
btree_err only jumps when the return from __btree_err does not match
fsck_fix. Ultimately this lead to undefined behavior by attempting to
unpack a key based on an invalid format.
Make only errors of type -BCH_ERR_btree_node_read_err_fixable cause
__btree_err to return -BCH_ERR_fsck_fix when scanning for btree nodes.
Reported-by: syzbot+cfd994b9cdf00446fd54@syzkaller.appspotmail.com
Fixes: cd3cdb1ef7 ("bcachefs: Single err message for btree node reads")
Signed-off-by: Bharadwaj Raju <bharadwaj.raju777@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Add a mount option for rewinding the journal, bringing the entire
filesystem to where it was at a previous point in time.
This is for extreme disaster recovery scenarios - it's not intended as
an undelete operation.
The option takes a journal sequence number; the desired sequence number
can be determined with 'bcachefs list_journal'
Caveats:
- The 'journal_transaction_names' option must have been enabled (it's on
by default). The option controls emitting of extra debug info in the
journal, so we can see what individual transactions were doing;
It also enables journalling of keys being overwritten, which is what
we rely on here.
- A full fsck run will be automatically triggered since alloc info will
be inconsistent. Only leaf node updates to non-alloc btrees are
rewound, since rewinding interior btree updates isn't possible or
desirable.
- We can't do anything about data that was deleted and overwritten.
Lots of metadata updates after the point in time we're rewinding to
shouldn't cause a problem, since we segragate data and metadata
allocations (this is in order to make repair by btree node scan
practical on larger filesystems; there's a small 64-bit per device
bitmap in the superblock of device ranges with btree nodes, and we try
to keep this small).
However, having discards enabled will cause problems, since buckets
are discarded as soon as they become empty (this is why we don't
implement fstrim: we don't need it).
Hopefully, this feature will be a one-off thing that's never used
again: this was implemented for recovering from the "vfs i_nlink 0 ->
subvol deletion" bug, and that bug was unusually disastrous and
additional safeguards have since been implemented.
But if it does turn out that we need this more in the future, I'll
have to implement an option so that empty buckets aren't discarded
immediately - lagging by perhaps 1% of device capacity.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Number of apqn target list entries contained in 'nr_apqns' variable is
determined by userspace via an ioctl call so the result of the product in
calculation of size passed to memdup_user() may overflow.
In this case the actual size of the allocated area and the value
describing it won't be in sync leading to various types of unpredictable
behaviour later.
Use a proper memdup_array_user() helper which returns an error if an
overflow is detected. Note that it is different from when nr_apqns is
initially zero - that case is considered valid and should be handled in
subsequent pkey_handler implementations.
Found by Linux Verification Center (linuxtesting.org).
Fixes: f2bbc96e7c ("s390/pkey: add CCA AES cipher key support")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250611192011.206057-1-pchelkin@ispras.ru
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Fix the case where we're deleting in a different snapshot and need to
emit a whiteout - that requires a regular BTREE_ITER_filter_snapshots
iterator.
Also, only delete the part of the extent that extents past i_size.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
When the inode was a whiteout, we were inserting a new whiteout at the
wrong (old) snapshot.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Prep work for journal rewind, where the seq we're replaying from may be
different than the last journal entry's last_seq.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Previously, we weren't checking the result of the skiplist walk, just
the is_ancestor bitmap.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
We need to start searching from search_key - _not_ path->pos, which will
point to the key we found in the btree
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
this code is rarely invoked, so - we had a few bugs left from basing it
off of bch2_journal_keys_peek_max()...
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Allocating new memory when mempool is exhausted is too complicated, just
return ENOMEM is fine. memcpy is not needed, since there might be
pointers point to the old memory, that's the bug.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
We've been seeing some livelock-ish behavior in the index update part of
the main write path, and while we've got low level btree path
tracepoints, we've been lacking high level btree iterator tracepoints.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
By inspection, cxl_cper_handle_prot_err() is making a series of fragile
assumptions that can lead to crashes:
1/ It assumes that endpoints identified in the record are a CXL-type-3
device, nothing guarantees that.
2/ It assumes that the device is bound to the cxl_pci driver, nothing
guarantees that.
3/ Minor, it holds the device lock over the switch-port tracing for no
reason as the trace is 100% generated from data in the record.
Correct those by checking that the PCIe endpoint parents a cxl_memdev
before assuming the format of the driver data, and move the lock to where
it is required. Consequently this also makes the implementation ready for
CXL accelerators that are not bound to cxl_pci.
Fixes: 36f257e3b0 ("acpi/ghes, cxl/pci: Process CXL CPER Protocol Errors")
Cc: Terry Bowman <terry.bowman@amd.com>
Cc: Li Ming <ming.li@zohomail.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Li Ming <ming.li@zohomail.com>
Link: https://patch.msgid.link/20250612192043.2254617-1-dan.j.williams@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
I must have lost this rebasing things during the merge window, I know I
got it at some point but it's not here now. Without this I get warnings
along the lines of
include/linux/fs.h:3975:15: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
3975 | if (unlikely(get_user(c, path)))
| ^
arch/riscv/include/asm/uaccess.h:274:3: note: expanded from macro 'get_user'
274 | __get_user((x), __p) : \
| ^
arch/riscv/include/asm/uaccess.h:244:2: note: expanded from macro '__get_user'
244 | __get_user_error(__gu_val, __gu_ptr, __gu_err); \
| ^
arch/riscv/include/asm/uaccess.h:207:2: note: expanded from macro '__get_user_error'
207 | __ge LD [M] net/802/psnap.ko
t_user_nocheck(x, ptr, __gu_failed); \
| ^
arch/riscv/include/asm/uaccess.h:196:3: note: expanded from macro '__get_user_nocheck'
196 | __get_user_8((x), __gu_ptr, label); \
| ^
arch/riscv/include/asm/uaccess.h:130:2: note: expanded from macro '__get_user_8'
130 | u32 __user *__ptr = (u32 __user *)(ptr); \
| ^
Link: https://lore.kernel.org/r/20250610213058.24852-1-palmer@dabbelt.com
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: stable@vger.kernel.org
Fixes: f6bff7827a ("riscv: uaccess: use 'asm_goto_output' for get_user()")
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
When running the raid6 user-space test program on RISC-V QEMU, there's a
segmentation fault which seems caused by accessing a NULL pointer,
which is the pointer variable p/q in raid6_rvv*_gen/xor_syndrome_real(),
p/q should have been equal to dptr[x], but when I use GDB command to
see its value, which was 0x10 like below:
"
Program received signal SIGSEGV, Segmentation fault.
0x0000000000011062 in raid6_rvv2_xor_syndrome_real (disks=<optimized out>, start=0, stop=<optimized out>, bytes=4096, ptrs=<optimized out>) at rvv.c:386
(gdb) p p
$1 = (u8 *) 0x10 <error: Cannot access memory at address 0x10>
"
The issue was found to be related with:
1) Compile optimization
There's no segmentation fault if compiling the raid6test program with
the optimization flag -O0.
2) The RISC-V vector command vsetvli
If not used t0 as the first parameter in vsetvli, there's no
segmentation fault either.
This patch selects the 2nd solution to fix the issue.
[Palmer: The actual issue here is a missing clobber in the vsetvli code.
It's a little tricky: we've already probed for VLENB so we don't need to
look at the output register, we just need to have an X register in the
instruction as that's the form required to actually set VL. Thus we
clobber a register, and without describing that we end up breaking
compilers.]
Fixes: 6093faaf95 ("raid6: Add RISC-V SIMD syndrome and recovery calculations")
Signed-off-by: Chunyan Zhang <zhangchunyan@iscas.ac.cn>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250610101234.1100660-3-zhangchunyan@iscas.ac.cn
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
riscv fixes for 6.16-rc1
- A fix for the newly introduced getrandom vdso where clang optimizes
away a register variable which is both an input and an output
parameter
- A fix for theadvector where we did not save all the vector registers,
only a few of them
* tag 'riscv-fixes-6.16-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/alexghiti/linux:
RISC-V: vDSO: Correct inline assembly constraints in the getrandom syscall wrapper
riscv: vector: Fix context save/restore with xtheadvector
Convert the Altera JTAG UART binding to DT schema. The "ALTR,uart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Convert the Altera JTAG UART binding to DT schema. The "ALTR,juart-1.0"
compatible has long been deprecated, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
the `__runtime_fixup_32` function does not handle the case where `val` is
zero correctly (as might occur when patching a nommu kernel and referring
to a physical address below the 4GiB boundary whose upper 32 bits are all
zero) because nothing in the existing logic prevents the code from taking
the `else` branch of both nop-checks and emitting two `nop` instructions.
This leaves random garbage in the register that is supposed to receive the
upper 32 bits of the pointer instead of zero that when combined with the
value for the lower 32 bits yields an invalid pointer and causes a kernel
panic when that pointer is eventually accessed.
The author clearly considered the fact that if the `lui` is converted into
a `nop` that the second instruction needs to be adjusted to become an `li`
instead of an `addi`, hence introducing the `addi_insn_mask` variable, but
didn't follow that logic through fully to the case where the `else` branch
executes. To fix it just adjust the logic to ensure that the second `else`
branch is not taken if the first instruction will be patched to a `nop`.
Fixes: a44fb57221 ("riscv: Add runtime constant support")
Signed-off-by: Charles Mirabile <cmirabil@redhat.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Tested-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20250530211422.784415-2-cmirabil@redhat.com
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Commit fd2a9b29dc ("HID: wacom: Remove AES power_supply after extended
inactivity") introduced wacom_aes_battery_handler() which is scheduled
as a delayed work (aes_battery_work).
In wacom_remove(), aes_battery_work is not canceled. Consequently, if
the device is removed while aes_battery_work is still pending, then hard
crashes or "Oops: general protection fault..." are experienced when
wacom_aes_battery_handler() is finally called. E.g., this happens with
built-in USB devices after resume from hibernate when aes_battery_work
was still pending at the time of hibernation.
So, take care to cancel aes_battery_work in wacom_remove().
Fixes: fd2a9b29dc ("HID: wacom: Remove AES power_supply after extended inactivity")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When trying to update the scrub_cycle value of a cxl region, which means
updating the scrub_cycle value of each memdev under a cxl region. cxl
driver needs to guarantee the new scrub_cycle value is greater than the
min_scrub_cycle value of a memdev, otherwise the updating operation will
fail(Per Table 8-223 in CXL r3.2 section 8.2.10.9.11.1).
Current implementation logic of getting the min_scrub_cycle value of a
cxl region is that getting the min_scrub_cycle value of each memdevs
under the cxl region, then using the minimum min_scrub_cycle value as
the region's min_scrub_cycle. Checking if the new scrub_cycle value is
greater than this value. If yes, updating the new scrub_cycle value to
each memdevs. The issue is that the new scrub_cycle value is possibly
greater than the minimum min_scrub_cycle value of all memdevs but less
than the maximum min_scrub_cycle value of all memdevs if memdevs have
a different min_scrub_cycle value. The updating operation will always
fail on these memdevs which have a greater min_scrub_cycle than the new
scrub_cycle.
The correct implementation logic is to get the maximum value of these
memdevs' min_scrub_cycle, check if the new scrub_cycle value is greater
than the value. If yes, the new scrub_cycle value is fit for the region.
The change also impacts the result of
cxl_patrol_scrub_get_min_scrub_cycle(), the interface returned the
minimum min_scrub_cycle value among all memdevs under the region before
the change. The interface will return the maximum min_scrub_cycle value
among all memdevs under the region with the change.
Signed-off-by: Li Ming <ming.li@zohomail.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Shiju Jose <shiju.jose@huawei.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://patch.msgid.link/20250603104314.25569-1-ming.li@zohomail.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
.rodata is implicitly included in the PT_DYNAMIC segment due to
inheriting the segment of the preceding .dynamic section (in both GNU ld
and LLD). When the .rodata section's size is not a multiple of 16
bytes on riscv64, llvm-readelf will report a "PT_DYNAMIC dynamic table
is invalid" warning. Note: in the presence of the .dynamic section, GNU
readelf and llvm-readelf's -d option decodes the dynamic section using
the section.
This issue arose after commit 8f8c1ff879
("riscv: vdso.lds.S: remove hardcoded 0x800 .text start addr"), which
placed .rodata directly after .dynamic by removing .eh_frame.
This patch resolves the implicit inclusion into PT_DYNAMIC by explicitly
specifying the :text output section phdr.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2093
Signed-off-by: Fangrui Song <i@maskray.me>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250602-riscv-vdso-v1-1-0620cf63cff0@maskray.me
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Replace the usage of PCI_VDEVICE() with driver_data assignment in the ISH
PCI device table with the PCI_DEVICE_DATA() macro. This improves code
readability.
Signed-off-by: Zhang Lixu <lixu.zhang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 2f2bd7cbd1 ("hid: lenovo: Resend all settings on reset_resume
for compact keyboards") introduced a regression for ThinkPad TrackPoint
Keyboard II by removing the conditional check for enabling F7/9/11 mode
needed for compact keyboards only. As a result, the non-compact
keyboards can no longer toggle Fn-lock via Fn+Esc, although it can be
controlled via sysfs knob that directly sends raw commands.
This patch restores the previous conditional check without any
additions.
Cc: stable@vger.kernel.org
Fixes: 2f2bd7cbd1 ("hid: lenovo: Resend all settings on reset_resume for compact keyboards")
Signed-off-by: Iusico Maxim <iusico.maxim@libero.it>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
MARTLINKTECHNOLOGY is a microphone device, when the HID interface in an
audio device is requested to get specific report id, the following error
may occur.
[ 562.939373] usb 1-1.4.1.2: new full-speed USB device number 21 using xhci_hcd
[ 563.104908] usb 1-1.4.1.2: New USB device found, idVendor=4c4a, idProduct=4155, bcdDevice= 1.00
[ 563.104910] usb 1-1.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 563.104911] usb 1-1.4.1.2: Product: USB Composite Device
[ 563.104912] usb 1-1.4.1.2: Manufacturer: SmartlinkTechnology
[ 563.104913] usb 1-1.4.1.2: SerialNumber: 20201111000001
[ 563.229499] input: SmartlinkTechnology USB Composite Device as /devices/pci0000:00/0000:00:07.1/0000:04:00.3/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1.2/1-1.4.1.2:1.2/0003:4C4A:4155.000F/input/input35
[ 563.291505] hid-generic 0003:4C4A:4155.000F: input,hidraw2: USB HID v2.01 Keyboard [SmartlinkTechnology USB Composite Device] on usb-0000:04:00.3-1.4.1.2/input2
[ 563.291557] usbhid 1-1.4.1.2:1.3: couldn't find an input interrupt endpoint
[ 568.506654] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 573.626656] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 578.746657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 583.866655] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 588.986657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
Ignore HID interface. The device is working properly.
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Plugging in a "Blue snowball" microphone always shows the
error 'No inputs registered, leaving', but the device functions as
intended.
When a HID device is started using the function hid_hw_start() and
the argument HID_CONNECT_DEFAULT it will try all various hid connect
requests. Not all devices will create an input device and so the
message is needlessly noisy. Decrease it to debug instead.
[jkosina@suse.com: edit shortlog]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C)
report a HID sensor interface that is not actually implemented.
Attempting to access this non-functional sensor via iio_info causes
system hangs as runtime PM tries to wake up an unresponsive sensor.
Add these 2 devices to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During customer board enabling, it was found: some touch devices
prepared reset response, but either forgot sending interrupt or
THC missed reset interrupt because of timing issue. THC QuickI2C
driver depends on interrupt to read reset response, in this case,
it will cause driver waiting timeout.
This patch enhances the flow by adding manually reset response
reading after waiting for reset interrupt timeout.
Signed-off-by: Even Xu <even.xu@intel.com>
Tested-by: Chong Han <chong.han@intel.com>
Fixes: 66b59bfce6 ("HID: intel-thc-hid: intel-quicki2c: Complete THC QuickI2C driver")
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Ensure we don't stall or panic the kernel when using bluetooth-connected
controllers. This was reported as an issue on android devices using
kernel 6.6 due to the resume hook which had been added for usb joycons.
First, set a new state value to JOYCON_CTLR_STATE_SUSPENDED in a
newly-added nintendo_hid_suspend. This makes sure we will not stall out
the kernel waiting for input reports during led classdev suspend. The
stalls could happen if connectivity is unreliable or lost to the
controller prior to suspend.
Second, since we lose connectivity during suspend, do not try
joycon_init() for bluetooth controllers in the nintendo_hid_resume path.
Tested via multiple suspend/resume flows when using the controller both
in USB and bluetooth modes.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Reviewed-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When sysfs_create_files() fails in wacom_initialize_remotes() the error
is returned and the cleanup action will not have been registered yet.
As a result the kobject???s refcount is never dropped, so the
kobject can never be freed leading to a reference leak.
Fix this by calling kobject_put() before returning.
Fixes: 83e6b40e2d ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When sysfs_create_files() fails during wacom_initialize_remotes() the
fifo buffer is not freed leading to a memory leak.
Fix this by calling kfifo_free() before returning.
Fixes: 83e6b40e2d ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During wacom_initialize_remotes() a fifo buffer is allocated
with kfifo_alloc() and later a cleanup action is registered
during devm_add_action_or_reset() to clean it up.
However if the code fails to create a kobject and register it
with sysfs the code simply returns -ENOMEM before the cleanup
action is registered leading to a memory leak.
Fix this by ensuring the fifo is freed when the kobject creation
and registration process fails.
Fixes: 83e6b40e2d ("HID: wacom: EKR: have the wacom resources dynamically allocated")
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Qasim Ijaz <qasdev00@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The cxlctl_validate_set_features() function is type bool. It's supposed
to return true for valid requests and false for invalid. However, this
error path returns ERR_PTR(-EINVAL) which is true when it was intended to
return false.
The incorrect return will result in kernel failing to prevent a
incorrect op_size passed in from userspace to be detected.
[ dj: Add user impact to commit log ]
Fixes: f76e0bbc8b ("cxl: Update prototype of function get_support_feature_info()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/aDbFPSCujpJLY1if@stanley.mountain
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
In the zoned mode there's a bug in the extent buffer tree conversion to
xarray. The reference for eb is dropped and code continues but the
references get dropped by releasing the batch.
Reported-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Fixes: 19d7f65f03 ("btrfs: convert the buffer_radix to an xarray")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
2025-05-27 13:26:28 +02:00
328 changed files with 3489 additions and 1998 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.