Merge misc fixes from Andrew Morton:
"Five fixes.
Subsystems affected by this patch series: MAINTAINERS, mm/pagemap,
mm/swap, and mm/hugetlb"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: khugepaged: recalculate min_free_kbytes after memory hotplug as expected by khugepaged
mm: validate inode in mapping_set_error()
mm: mmap: Fix general protection fault in unlink_file_vma()
MAINTAINERS: Antoine Tenart's email address
MAINTAINERS: change hardening mailing list
Pull vfs fix from Al Viro:
"Fixes an obvious bug (memory leak introduced in 5.8)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
pipe: Fix memory leaks in create_pipe_files()
Pull x86 fixes from Ingo Molnar:
"Two fixes:
- Fix a (hopefully final) IRQ state tracking bug vs MCE handling
- Fix a documentation link"
* tag 'x86-urgent-2020-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation/x86: Fix incorrect references to zero-page.txt
x86/mce: Use idtentry_nmi_enter/exit()
Pull perf fix from Ingo Molnar:
"Fix an error handling bug that can cause a lockup if a CPU is offline
(doh ...)"
* tag 'perf-urgent-2020-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix task_function_call() error handling
The syzbot reported the below general protection fault:
general protection fault, probably for non-canonical address
0xe00eeaee0000003b: 0000 [#1] PREEMPT SMP KASAN
KASAN: maybe wild-memory-access in range [0x00777770000001d8-0x00777770000001df]
CPU: 1 PID: 10488 Comm: syz-executor721 Not tainted 5.9.0-rc3-syzkaller #0
RIP: 0010:unlink_file_vma+0x57/0xb0 mm/mmap.c:164
Call Trace:
free_pgtables+0x1b3/0x2f0 mm/memory.c:415
exit_mmap+0x2c0/0x530 mm/mmap.c:3184
__mmput+0x122/0x470 kernel/fork.c:1076
mmput+0x53/0x60 kernel/fork.c:1097
exit_mm kernel/exit.c:483 [inline]
do_exit+0xa8b/0x29f0 kernel/exit.c:793
do_group_exit+0x125/0x310 kernel/exit.c:903
get_signal+0x428/0x1f00 kernel/signal.c:2757
arch_do_signal+0x82/0x2520 arch/x86/kernel/signal.c:811
exit_to_user_mode_loop kernel/entry/common.c:136 [inline]
exit_to_user_mode_prepare+0x1ae/0x200 kernel/entry/common.c:167
syscall_exit_to_user_mode+0x7e/0x2e0 kernel/entry/common.c:242
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It's because the ->mmap() callback can change vma->vm_file and fput the
original file. But the commit d70cec8983 ("mm: mmap: merge vma after
call_mmap() if possible") failed to catch this case and always fput()
the original file, hence add an extra fput().
[ Thanks Hillf for pointing this extra fput() out. ]
Fixes: d70cec8983 ("mm: mmap: merge vma after call_mmap() if possible")
Reported-by: syzbot+c5d5a51dcbb558ca0cb5@syzkaller.appspotmail.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian König <ckoenig.leichtzumerken@gmail.com>
Cc: Hongxiang Lou <louhongxiang@huawei.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Link: https://lkml.kernel.org/r/20200916090733.31427-1-linmiaohe@huawei.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c fixes from Wolfram Sang:
"Some more driver bugfixes for I2C. Including a revert - the updated
series for it will come during the next merge window"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: owl: Clear NACK and BUS error bits
Revert "i2c: imx: Fix reset of I2SR_IAL flag"
i2c: meson: fixup rate calculation with filter delay
i2c: meson: keep peripheral clock enabled
i2c: meson: fix clock setting overwrite
i2c: imx: Fix reset of I2SR_IAL flag
On setxattr() syscall path due to an apprent typo the size of a dynamically
allocated memory chunk for storing struct smb2_file_full_ea_info object is
computed incorrectly, to be more precise the first addend is the size of
a pointer instead of the wanted object size. Coincidentally it makes no
difference on 64-bit platforms, however on 32-bit targets the following
memcpy() writes 4 bytes of data outside of the dynamically allocated memory.
=============================================================================
BUG kmalloc-16 (Not tainted): Redzone overwritten
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: 0x79e69a6f-0x9e5cdecf @offset=368. First byte 0x73 instead of 0xcc
INFO: Slab 0xd36d2454 objects=85 used=51 fp=0xf7d0fc7a flags=0x35000201
INFO: Object 0x6f171df3 @offset=352 fp=0x00000000
Redzone 5d4ff02d: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc ................
Object 6f171df3: 00 00 00 00 00 05 06 00 73 6e 72 75 62 00 66 69 ........snrub.fi
Redzone 79e69a6f: 73 68 32 0a sh2.
Padding 56254d82: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 0 PID: 8196 Comm: attr Tainted: G B 5.9.0-rc8+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
Call Trace:
dump_stack+0x54/0x6e
print_trailer+0x12c/0x134
check_bytes_and_report.cold+0x3e/0x69
check_object+0x18c/0x250
free_debug_processing+0xfe/0x230
__slab_free+0x1c0/0x300
kfree+0x1d3/0x220
smb2_set_ea+0x27d/0x540
cifs_xattr_set+0x57f/0x620
__vfs_setxattr+0x4e/0x60
__vfs_setxattr_noperm+0x4e/0x100
__vfs_setxattr_locked+0xae/0xd0
vfs_setxattr+0x4e/0xe0
setxattr+0x12c/0x1a0
path_setxattr+0xa4/0xc0
__ia32_sys_lsetxattr+0x1d/0x20
__do_fast_syscall_32+0x40/0x70
do_fast_syscall_32+0x29/0x60
do_SYSENTER_32+0x15/0x20
entry_SYSENTER_32+0x9f/0xf2
Fixes: 5517554e43 ("cifs: Add support for writing attributes on SMB2+")
Signed-off-by: Vladimir Zapolskiy <vladimir@tuxera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been elusive reports of filemap_fault() hitting its
VM_BUG_ON_PAGE(page_to_pgoff(page) != offset, page) on kernels built
with CONFIG_READ_ONLY_THP_FOR_FS=y.
Suren has hit it on a kernel with CONFIG_READ_ONLY_THP_FOR_FS=y and
CONFIG_NUMA is not set: and he has analyzed it down to how khugepaged
without NUMA reuses the same huge page after collapse_file() failed
(whereas NUMA targets its allocation to the respective node each time).
And most of us were usually testing with CONFIG_NUMA=y kernels.
collapse_file(old start)
new_page = khugepaged_alloc_page(hpage)
__SetPageLocked(new_page)
new_page->index = start // hpage->index=old offset
new_page->mapping = mapping
xas_store(&xas, new_page)
filemap_fault
page = find_get_page(mapping, offset)
// if offset falls inside hpage then
// compound_head(page) == hpage
lock_page_maybe_drop_mmap()
__lock_page(page)
// collapse fails
xas_store(&xas, old page)
new_page->mapping = NULL
unlock_page(new_page)
collapse_file(new start)
new_page = khugepaged_alloc_page(hpage)
__SetPageLocked(new_page)
new_page->index = start // hpage->index=new offset
new_page->mapping = mapping // mapping becomes valid again
// since compound_head(page) == hpage
// page_to_pgoff(page) got changed
VM_BUG_ON_PAGE(page_to_pgoff(page) != offset)
An initial patch replaced __SetPageLocked() by lock_page(), which did
fix the race which Suren illustrates above. But testing showed that it's
not good enough: if the racing task's __lock_page() gets delayed long
after its find_get_page(), then it may follow collapse_file(new start)'s
successful final unlock_page(), and crash on the same VM_BUG_ON_PAGE.
It could be fixed by relaxing filemap_fault()'s VM_BUG_ON_PAGE to a
check and retry (as is done for mapping), with similar relaxations in
find_lock_entry() and pagecache_get_page(): but it's not obvious what
else might get caught out; and khugepaged non-NUMA appears to be unique
in exposing a page to page cache, then revoking, without going through
a full cycle of freeing before reuse.
Instead, non-NUMA khugepaged_prealloc_page() release the old page
if anyone else has a reference to it (1% of cases when I tested).
Although never reported on huge tmpfs, I believe its find_lock_entry()
has been at similar risk; but huge tmpfs does not rely on khugepaged
for its normal working nearly so much as READ_ONLY_THP_FOR_FS does.
Reported-by: Denis Lisov <dennis.lissov@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206569
Link: https://lore.kernel.org/linux-mm/?q=20200219144635.3b7417145de19b65f258c943%40linux-foundation.org
Reported-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/linux-xfs/?q=20200616013309.GB815%40lca.pw
Reported-and-analyzed-by: Suren Baghdasaryan <surenb@google.com>
Fixes: 87c460a0bd ("mm/khugepaged: collapse_shmem() without freezing new_page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # v4.9+
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af4 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit fa4d305568. An updated
version was sent. So, revert this version and give the new version more
time for testing.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull spi fix from Mark Brown:
"One last minute fix for v5.9 which has been causing crashes in test
systems with the fsl-dspi driver when they hit deferred probe (and
which I probably let cook in next a bit longer than is ideal).
And an update to MAINTAINERS reflecting Serge's extensive and
detailed recent work on the DesignWare driver"
* tag 'spi-fix-v5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
MAINTAINERS: Add maintainer of DW APB SSI driver
spi: fsl-dspi: fix NULL pointer dereference
Pull RISC-V fixes from Palmer Dabbelt:
"Two fixes this week:
- A fix to actually reserve the device tree's memory. Without this
the device tree can be overwritten on systems that don't otherwise
reserve it. This issue should only manifest on !MMU systems.
- A workaround for a BUG() that triggers when the memory that
originally contained initdata is freed and later repurposed. This
triggers a BUG() on builds that had HARDENED_USERCOPY enabled"
* tag 'riscv-for-linus-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fixup bootup failure with HARDENED_USERCOPY
RISC-V: Make sure memblock reserves the memory containing DT
Pull power supply fix from Sebastian Reichel:
"Just a single change to revert enablement of packet error checking for
battery data on Chromebooks, since some of their embedded controllers
do not handle it correctly"
* tag 'for-v5.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sbs-battery: chromebook workaround for PEC
Pull GPIO fixes from Linus Walleij:
"Some late fixes: one IRQ issue and one compilation issue for UML.
- Fix a compilation issue with User Mode Linux
- Handle spurious interrupts properly in the PCA953x driver"
* tag 'gpio-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Survive spurious interrupts
gpiolib: Disable compat ->read() code in UML case
Pull MMC fix from Ulf Hansson:
"Assign a proper discard granularity rather than incorrectly set it to
zero"
* tag 'mmc-v5.9-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: don't set limits.discard_granularity as 0
Pull amdgpu drm fixes from Dave Airlie:
"Fixes trickling in this week.
Alex had a final fix for the newest GPU they introduced in rc1, along
with one build regression and one crasher fix.
Cross my fingers that's it for 5.9:
- Fix a crash on renoir if you override the IP discovery parameter
- Fix the build on ARC platforms
- Display fix for Sienna Cichlid"
* tag 'drm-fixes-2020-10-09' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Change ABM config init interface
drm/amdgpu/swsmu: fix ARC build errors
drm/amdgpu: fix NULL pointer dereference for Renoir
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
WARNING: CPU: 0 PID: 135 at __blkdev_issue_discard+0x200/0x294
CPU: 0 PID: 135 Comm: f2fs_discard-17 Not tainted 5.9.0-rc6 #1
Hardware name: Google Kevin (DT)
pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
pc : __blkdev_issue_discard+0x200/0x294
lr : __blkdev_issue_discard+0x54/0x294
sp : ffff800011dd3b10
x29: ffff800011dd3b10 x28: 0000000000000000 x27: ffff800011dd3cc4 x26: ffff800011dd3e18 x25: 000000000004e69b x24: 0000000000000c40 x23: ffff0000f1deaaf0 x22: ffff0000f2849200 x21: 00000000002734d8 x20: 0000000000000008 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000394 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 00000000000008b0 x9 : ffff800011dd3cb0 x8 : 000000000004e69b x7 : 0000000000000000 x6 : ffff0000f1926400 x5 : ffff0000f1940800 x4 : 0000000000000000 x3 : 0000000000000c40 x2 : 0000000000000008 x1 : 00000000002734d8 x0 : 0000000000000000 Call trace:
__blkdev_issue_discard+0x200/0x294
__submit_discard_cmd+0x128/0x374
__issue_discard_cmd_orderly+0x188/0x244
__issue_discard_cmd+0x2e8/0x33c
issue_discard_thread+0xe8/0x2f0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
---[ end trace e4c8023d33dfe77a ]---
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b6 ("mmc: queue: let host controllers specify maximum discard timeout")
Fixes: b35fd7422c ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()").
Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull block fixes from Jens Axboe:
"A few fixes that should go into this release:
- NVMe controller error path reference fix (Chaitanya)
- Fix regression with IBM partitions on non-dasd devices (Christoph)
- Fix a missing clear in the compat CDROM packet structure (Peilin)"
* tag 'block5.9-2020-10-08' of git://git.kernel.dk/linux-block:
partitions/ibm: fix non-DASD devices
nvme-core: put ctrl ref when module ref get fail
block/scsi-ioctl: Fix kernel-infoleak in scsi_put_cdrom_generic_arg()
Looks like the I2C tunnel implementation from Chromebook's
embedded controller does not handle PEC correctly. Fix this
by disabling PEC for batteries behind those I2C tunnels as
a workaround.
Note, that some Chromebooks actually have been reported to
have working PEC support (with I2C tunnel). Since the problem
has not yet been fully understood this simply reverts all
Chromebooks to not use PEC for now.
Reported-by: "Milan P. Stanić" <mps@arvanta.net>
Reported-by: Vicente Bergas <vicencb@gmail.com>
CC: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 7222bd603d ("power: supply: sbs-battery: add PEC support")
Tested-by: Vicente Bergas <vicencb@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull vhost fixes from Michael Tsirkin:
"Some last minute vhost,vdpa fixes.
The last two of them haven't been in next but they do seem kind of
obvious, very small and safe, fix bugs reported in the field, and they
are both in a new mlx5 vdpa driver, so it's not like we can introduce
regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Fix dependency on MLX5_CORE
vdpa/mlx5: should keep avail_index despite device status
vhost-vdpa: fix page pinning leakage in error path
vhost-vdpa: fix vhost_vdpa_map() on error condition
vhost: Don't call log_access_ok() when using IOTLB
vhost: Use vhost_get_used_size() in vhost_vring_set_addr()
vhost: Don't call access_ok() when using IOTLB
vhost vdpa: fix vhost_vdpa_open error handling
Pull networking fixes from Jakub Kicinski:
"One more set of fixes from the networking tree:
- add missing input validation in nl80211_del_key(), preventing
out-of-bounds access
- last minute fix / improvement of a MRP netlink (uAPI) interface
introduced in 5.9 (current) release
- fix "unresolved symbol" build error under CONFIG_NET w/o
CONFIG_INET due to missing tcp_timewait_sock and inet_timewait_sock
BTF.
- fix 32 bit sub-register bounds tracking in the bpf verifier for OR
case
- tcp: fix receive window update in tcp_add_backlog()
- openvswitch: handle DNAT tuple collision in conntrack-related code
- r8169: wait for potential PHY reset to finish after applying a FW
file, avoiding unexpected PHY behaviour and failures later on
- mscc: fix tail dropping watermarks for Ocelot switches
- avoid use-after-free in macsec code after a call to the GRO layer
- avoid use-after-free in sctp error paths
- add a device id for Cellient MPL200 WWAN card
- rxrpc fixes:
- fix the xdr encoding of the contents read from an rxrpc key
- fix a BUG() for a unsupported encoding type.
- fix missing _bh lock annotations.
- fix acceptance handling for an incoming call where the incoming
call is encrypted.
- the server token keyring isn't network namespaced - it belongs
to the server, so there's no need. Namespacing it means that
request_key() fails to find it.
- fix a leak of the server keyring"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (21 commits)
net: usb: qmi_wwan: add Cellient MPL200 card
macsec: avoid use-after-free in macsec_handle_frame()
r8169: consider that PHY reset may still be in progress after applying firmware
openvswitch: handle DNAT tuple collision
sctp: fix sctp_auth_init_hmacs() error path
bridge: Netlink interface fix.
net: wireless: nl80211: fix out-of-bounds access in nl80211_del_key()
bpf: Fix scalar32_min_max_or bounds tracking
tcp: fix receive window update in tcp_add_backlog()
net: usb: rtl8150: set random MAC address when set_ethernet_addr() fails
mptcp: more DATA FIN fixes
net: mscc: ocelot: warn when encoding an out-of-bounds watermark value
net: mscc: ocelot: divide watermark value by 60 when writing to SYS_ATOP
net: qrtr: ns: Fix the incorrect usage of rcu_read_lock()
rxrpc: Fix server keyring leak
rxrpc: The server keyring isn't network-namespaced
rxrpc: Fix accept on a connection that need securing
rxrpc: Fix some missing _bh annotations on locking conn->state_lock
rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()
rxrpc: Fix rxkad token xdr encoding
...
Remove propmt for selecting MLX5_VDPA by the user and modify
MLX5_VDPA_NET to select MLX5_VDPA. Also modify MLX5_VDPA_NET to depend
on mlx5_core.
This fixes an issue where configuration sets 'y' for MLX5_VDPA_NET while
MLX5_CORE is compiled as a module causing link errors.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 device")s
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201007064011.GA50074@mtl-vdi-166.wap.labs.mlnx
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A VM with mlx5 vDPA has below warnings while being reset:
vhost VQ 0 ring restore failed: -1: Resource temporarily unavailable (11)
vhost VQ 1 ring restore failed: -1: Resource temporarily unavailable (11)
We should allow userspace emulating the virtio device be
able to get to vq's avail_index, regardless of vDPA device
status. Save the index that was last seen when virtq was
stopped, so that userspace doesn't complain.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601583511-15138-1-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eli Cohen <elic@nvidia.com>
De-referencing skb after call to gro_cells_receive() is not allowed.
We need to fetch skb->len earlier.
Fixes: 5491e7c6b1 ("macsec: enable GRO and RPS on macsec devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.
For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10
Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.
Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.
Reported-at: https://bugzilla.redhat.com/1877128
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523e5 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
pull-request: mac80211 2020-10-08
A single fix for missing input validation in nl80211.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2020-10-08
The main changes are:
1) Fix "unresolved symbol" build error under CONFIG_NET w/o CONFIG_INET due
to missing tcp_timewait_sock and inet_timewait_sock BTF, from Yonghong Song.
2) Fix 32 bit sub-register bounds tracking for OR case, from Daniel Borkmann.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull drm nouveau fixes from Dave Airlie:
"Karol found two last minute nouveau fixes, they both fix crashes, the
TTM one follows what other drivers do already, and the other is for
bailing on load on unrecognised chipsets.
- fix crash in TTM alloc fail path
- return error earlier for unknown chipsets"
* tag 'drm-fixes-2020-10-08' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/mem: guard against NULL pointer access in mem_del
drm/nouveau/device: return error for unknown chipsets
Pull exfat fixes from Namjae Jeon:
- Fix use of uninitialized spinlock on error path
- Fix missing err assignment in exfat_build_inode()
* tag 'exfat-for-5.9-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: fix use of uninitialized spinlock on error path
exfat: fix pointer error checking
Pull xen fix from Juergen Gross:
"One fix for a regression when booting as a Xen guest on ARM64
introduced probably during the 5.9 cycle. It is very low risk as it is
modifying Xen specific code only.
The exact commit introducing the bug hasn't been identified yet, but
everything was fine in 5.8 and only in 5.9 some configurations started
to fail"
* tag 'for-linus-5.9b-rc9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/arm64: xen: Fix to convert percpu address to gfn correctly
The afs filesystem has a lock[*] that it uses to serialise I/O operations
going to the server (vnode->io_lock), as the server will only perform one
modification operation at a time on any given file or directory. This
prevents the the filesystem from filling up all the call slots to a server
with calls that aren't going to be executed in parallel anyway, thereby
allowing operations on other files to obtain slots.
[*] Note that is probably redundant for directories at least since
i_rwsem is used to serialise directory modifications and
lookup/reading vs modification. The server does allow parallel
non-modification ops, however.
When a file truncation op completes, we truncate the in-memory copy of the
file to match - but we do it whilst still holding the io_lock, the idea
being to prevent races with other operations.
However, if writeback starts in a worker thread simultaneously with
truncation (whilst notify_change() is called with i_rwsem locked, writeback
pays it no heed), it may manage to set PG_writeback bits on the pages that
will get truncated before afs_setattr_success() manages to call
truncate_pagecache(). Truncate will then wait for those pages - whilst
still inside io_lock:
# cat /proc/8837/stack
[<0>] wait_on_page_bit_common+0x184/0x1e7
[<0>] truncate_inode_pages_range+0x37f/0x3eb
[<0>] truncate_pagecache+0x3c/0x53
[<0>] afs_setattr_success+0x4d/0x6e
[<0>] afs_wait_for_operation+0xd8/0x169
[<0>] afs_do_sync_operation+0x16/0x1f
[<0>] afs_setattr+0x1fb/0x25d
[<0>] notify_change+0x2cf/0x3c4
[<0>] do_truncate+0x7f/0xb2
[<0>] do_sys_ftruncate+0xd1/0x104
[<0>] do_syscall_64+0x2d/0x3a
[<0>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
The writeback operation, however, stalls indefinitely because it needs to
get the io_lock to proceed:
# cat /proc/5940/stack
[<0>] afs_get_io_locks+0x58/0x1ae
[<0>] afs_begin_vnode_operation+0xc7/0xd1
[<0>] afs_store_data+0x1b2/0x2a3
[<0>] afs_write_back_from_locked_page+0x418/0x57c
[<0>] afs_writepages_region+0x196/0x224
[<0>] afs_writepages+0x74/0x156
[<0>] do_writepages+0x2d/0x56
[<0>] __writeback_single_inode+0x84/0x207
[<0>] writeback_sb_inodes+0x238/0x3cf
[<0>] __writeback_inodes_wb+0x68/0x9f
[<0>] wb_writeback+0x145/0x26c
[<0>] wb_do_writeback+0x16a/0x194
[<0>] wb_workfn+0x74/0x177
[<0>] process_one_work+0x174/0x264
[<0>] worker_thread+0x117/0x1b9
[<0>] kthread+0xec/0xf1
[<0>] ret_from_fork+0x1f/0x30
and thus deadlock has occurred.
Note that whilst afs_setattr() calls filemap_write_and_wait(), the fact
that the caller is holding i_rwsem doesn't preclude more pages being
dirtied through an mmap'd region.
Fix this by:
(1) Use the vnode validate_lock to mediate access between afs_setattr()
and afs_writepages():
(a) Exclusively lock validate_lock in afs_setattr() around the whole
RPC operation.
(b) If WB_SYNC_ALL isn't set on entry to afs_writepages(), trying to
shared-lock validate_lock and returning immediately if we couldn't
get it.
(c) If WB_SYNC_ALL is set, wait for the lock.
The validate_lock is also used to validate a file and to zap its cache
if the file was altered by a third party, so it's probably a good fit
for this.
(2) Move the truncation outside of the io_lock in setattr, using the same
hook as is used for local directory editing.
This requires the old i_size to be retained in the operation record as
we commit the revised status to the inode members inside the io_lock
still, but we still need to know if we reduced the file size.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 70e806e4e6 ("mm: Do early cow for pinned pages during fork()
for ptes") we write-protected the PTE before doing the page pinning
check, in order to avoid a race with concurrent fast-GUP pinning (which
doesn't take the mm semaphore or the page table lock).
That trick doesn't actually work - it doesn't handle memory ordering
properly, and doing so would be prohibitively expensive.
It also isn't really needed. While we're moving in the direction of
allowing and supporting page pinning without marking the pinned area
with MADV_DONTFORK, the fact is that we've never really supported this
kind of odd "concurrent fork() and page pinning", and doing the
serialization on a pte level is just wrong.
We can add serialization with a per-mm sequence counter, so we know how
to solve that race properly, but we'll do that at a more appropriate
time. Right now this just removes the write protect games.
It also turns out that the write protect games actually break on Power,
as reported by Aneesh Kumar:
"Architecture like ppc64 expects set_pte_at to be not used for updating
a valid pte. This is further explained in commit 56eecdb912 ("mm:
Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit")"
and the code triggered a warning there:
WARNING: CPU: 0 PID: 30613 at arch/powerpc/mm/pgtable.c:185 set_pte_at+0x2a8/0x3a0 arch/powerpc/mm/pgtable.c:185
Call Trace:
copy_present_page mm/memory.c:857 [inline]
copy_present_pte mm/memory.c:899 [inline]
copy_pte_range mm/memory.c:1014 [inline]
copy_pmd_range mm/memory.c:1092 [inline]
copy_pud_range mm/memory.c:1127 [inline]
copy_p4d_range mm/memory.c:1150 [inline]
copy_page_range+0x1f6c/0x2cc0 mm/memory.c:1212
dup_mmap kernel/fork.c:592 [inline]
dup_mm+0x77c/0xab0 kernel/fork.c:1355
copy_mm kernel/fork.c:1411 [inline]
copy_process+0x1f00/0x2740 kernel/fork.c:2070
_do_fork+0xc4/0x10b0 kernel/fork.c:2429
Link: https://lore.kernel.org/lkml/CAHk-=wiWr+gO0Ro4LvnJBMs90OiePNyrE3E+pJvc9PzdBShdmw@mail.gmail.com/
Link: https://lore.kernel.org/linuxppc-dev/20201008092541.398079-1-aneesh.kumar@linux.ibm.com/
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Leon Romanovsky <leonro@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Kirill Shutemov <kirill@shutemov.name>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
SCL rate appears to be different than what is expected. For example,
We get 164kHz on i2c3 of the vim3 when 400kHz is expected. This is
partially due to the peripheral clock being disabled when the clock is
set.
Let's keep the peripheral clock on after probe to fix the problem. This
does not affect the SCL output which is still gated when i2c is idle.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Simon reported an issue with the current scalar32_min_max_or() implementation.
That is, compared to the other 32 bit subreg tracking functions, the code in
scalar32_min_max_or() stands out that it's using the 64 bit registers instead
of 32 bit ones. This leads to bounds tracking issues, for example:
[...]
8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
8: (79) r1 = *(u64 *)(r0 +0)
R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
9: (b7) r0 = 1
10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
10: (18) r2 = 0x600000002
12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
12: (ad) if r1 < r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: (95) exit
14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
14: (25) if r1 > 0x0 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: (95) exit
16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
16: (47) r1 |= 0
17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x1; 0x700000000),s32_max_value=1,u32_max_value=1) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
[...]
The bound tests on the map value force the upper unsigned bound to be 25769803777
in 64 bit (0b11000000000000000000000000000000001) and then lower one to be 1. By
using OR they are truncated and thus result in the range [1,1] for the 32 bit reg
tracker. This is incorrect given the only thing we know is that the value must be
positive and thus 2147483647 (0b1111111111111111111111111111111) at max for the
subregs. Fix it by using the {u,s}32_{min,max}_value vars instead. This also makes
sense, for example, for the case where we update dst_reg->s32_{min,max}_value in
the else branch we need to use the newly computed dst_reg->u32_{min,max}_value as
we know that these are positive. Previously, in the else branch the 64 bit values
of umin_value=1 and umax_value=32212254719 were used and latter got truncated to
be 1 as upper bound there. After the fix the subreg range is now correct:
[...]
8: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
8: (79) r1 = *(u64 *)(r0 +0)
R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R10=fp0 fp-8=mmmmmmmm
9: R0=map_value(id=0,off=0,ks=4,vs=48,imm=0) R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
9: (b7) r0 = 1
10: R0_w=inv1 R1_w=inv(id=0) R10=fp0 fp-8=mmmmmmmm
10: (18) r2 = 0x600000002
12: R0_w=inv1 R1_w=inv(id=0) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
12: (ad) if r1 < r2 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: R0_w=inv1 R1_w=inv(id=0,umin_value=25769803778) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
13: (95) exit
14: R0_w=inv1 R1_w=inv(id=0,umax_value=25769803777,var_off=(0x0; 0x7ffffffff)) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
14: (25) if r1 > 0x0 goto pc+1
R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: R0_w=inv1 R1_w=inv(id=0,umax_value=0,var_off=(0x0; 0x7fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
15: (95) exit
16: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=25769803777,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
16: (47) r1 |= 0
17: R0_w=inv1 R1_w=inv(id=0,umin_value=1,umax_value=32212254719,var_off=(0x0; 0x77fffffff),u32_max_value=2147483647) R2_w=inv25769803778 R10=fp0 fp-8=mmmmmmmm
[...]
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Simon Scannell <scannell.smn@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
We want to use the dev_* functions here rather than the pr_* variants.
Switch to using dev_warn() which mirrors what we do on other asics.
Fixes the following build errors on ARC:
../drivers/gpu/drm/amd/amdgpu/../powerplay/navi10_ppt.c: In function 'navi10_fill_i2c_req':
../arch/arc/include/asm/bug.h:24:2: error: implicit declaration of function 'pr_warn'; did you mean 'drm_warn'? [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdgpu/../powerplay/sienna_cichlid_ppt.c: In function 'sienna_cichlid_fill_i2c_req':
../arch/arc/include/asm/bug.h:24:2: error: implicit declaration of function 'pr_warn'; did you mean 'drm_warn'? [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Evan Quan <evan.quan@amd.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit c1cf79ca5c ("drm/amdgpu: use IP discovery table for renoir")
introduced a NULL pointer dereference when booting with
amdgpu.discovery=0, because it removed the call of vega10_reg_base_init()
for that case.
Fix this by calling that funcion if amdgpu_discovery == 0 in addition to
the case that amdgpu_discovery_reg_base_init() failed.
Fixes: c1cf79ca5c ("drm/amdgpu: use IP discovery table for renoir")
Signed-off-by: Dirk Gouders <dirk@gouders.net>
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull NVMe fix from Christoph:
"nvme fix for 5.9:
- fix a recently introduced controller leak (Logan Gunthorpe)"
* tag 'nvme-5.9-2020-10-07' of git://git.infradead.org/nvme:
nvme-core: put ctrl ref when module ref get fail
The pca953x driver never checks the result of irq_find_mapping(),
which returns 0 when no mapping is found. When a spurious interrupt
is delivered (which can happen under obscure circumstances), the
kernel explodes as it still tries to handle the error code as
a real interrupt.
Handle this particular case and warn on spurious interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201005140217.1390851-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When try_module_get() fails in the nvme_dev_open() it returns without
releasing the ctrl reference which was taken earlier.
Put the ctrl reference which is taken before calling the
try_module_get() in the error return code path.
Fixes: 52a3974feb "nvme-core: get/put ctrl and transport module in nvme_dev_open/release()"
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix missing result check of exfat_build_inode().
And use PTR_ERR_OR_ZERO instead of PTR_ERR.
Signed-off-by: Tetsuhiro Kohada <kohada.t2@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
6184358da0 ("riscv: Fixup static_obj() fail") attempted to elide a lockdep
failure by rearranging our kernel image to place all initdata within [_stext,
_end], thus triggering lockdep to treat these as static objects. These objects
are released and eventually reallocated, causing check_kernel_text_object() to
trigger a BUG().
This backs out the change to make [_stext, _end] all-encompassing, instead just
moving initdata. This results in initdata being outside of [__init_begin,
__init_end], which means initdata can't be freed.
Link: https://lore.kernel.org/linux-riscv/1593266228-61125-1-git-send-email-guoren@kernel.org/T/#t
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
[Palmer: Clean up commit text]
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Pull arm64 fix from Catalin Marinas:
"Fix a kernel panic in the AES crypto code caused by a BR tail call not
matching the target BTI instruction (when branch target identification
is enabled)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
crypto: arm64: Use x16 with indirect branch to bti_c
Pull another x86 platform driver fix from Hans de Goede:
"One final pdx86 fix for Tablet Mode reporting regressions (which make
the keyboard and touchpad unusable) on various Asus notebooks.
These regressions were caused by the asus-nb-wmi and the intel-vbtn
drivers both receiving recent patches to start reporting Tablet Mode /
to report it on more models.
Due to a miscommunication between Andy and me, Andy's earlier pull-req
only contained the fix for the intel-vbtn driver and not the fix for
the asus-nb-wmi code.
This fix has been tested as a downstream patch in Fedora kernels for
approx two weeks with no problems being reported"
* tag 'platform-drivers-x86-v5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Fix SW_TABLET_MODE always reporting 1 on many different models
Pull drm fixes from Dave Airlie:
"Daniel queued these up last week and I took a long weekend so didn't
get them out, but fixing the OOB access on get font seems like
something we should land and it's cc'ed stable as well.
The other big change is a partial revert for a regression on android
on the clcd fbdev driver, and one other docs fix.
fbdev:
- Re-add FB_ARMCLCD for android
- Fix global-out-of-bounds read in fbcon_get_font()
core:
- Small doc fix"
* tag 'drm-fixes-2020-10-06-1' of git://anongit.freedesktop.org/drm/drm:
drm: drm_dsc.h: fix a kernel-doc markup
Partially revert "video: fbdev: amba-clcd: Retire elder CLCD driver"
fbcon: Fix global-out-of-bounds read in fbcon_get_font()
Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts
fbdev, newport_con: Move FONT_EXTRA_WORDS macros into linux/font.h
Kernel threads intentionally do CLONE_FS in order to follow any changes
that 'init' does to set up the root directory (or cwd).
It is admittedly a bit odd, but it avoids the situation where 'init'
does some extensive setup to initialize the system environment, and then
we execute a usermode helper program, and it uses the original FS setup
from boot time that may be very limited and incomplete.
[ Both Al Viro and Eric Biederman point out that 'pivot_root()' will
follow the root regardless, since it fixes up other users of root (see
chroot_fs_refs() for details), but overmounting root and doing a
chroot() would not. ]
However, Vegard Nossum noticed that the CLONE_FS not only means that we
follow the root and current working directories, it also means we share
umask with whatever init changed it to. That wasn't intentional.
Just reset umask to the original default (0022) before actually starting
the usermode helper program.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa reports that splice() can return 0 before the real EOF, if
the data in the splice source pipe is an empty pipe buffer. That empty
pipe buffer case doesn't happen in any normal situation, but you can
trigger it by doing a write to a pipe that fails due to a page fault.
Tetsuo has a test-case to show the behavior:
#define _GNU_SOURCE
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int fd = open("/tmp/testfile", O_WRONLY | O_CREAT, 0600);
int pipe_fd[2] = { -1, -1 };
pipe(pipe_fd);
write(pipe_fd[1], NULL, 4096);
/* This splice() should wait unless interrupted. */
return !splice(pipe_fd[0], NULL, fd, NULL, 65536, 0);
}
which results in
write(5, NULL, 4096) = -1 EFAULT (Bad address)
splice(4, NULL, 3, NULL, 65536, 0) = 0
and this can confuse splice() users into believing they have hit EOF
prematurely.
The issue was introduced when the pipe write code started pre-allocating
the pipe buffers before copying data from user space.
This is modified verion of Tetsuo's original patch.
Fixes: a194dfe6e6 ("pipe: Rearrange sequence in pipe_write() to preallocate slot")
Link:https://lore.kernel.org/linux-fsdevel/20201005121339.4063-1-penguin-kernel@I-love.SAKURA.ne.jp/
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AES code uses a 'br x7' as part of a function called by
a macro. That branch needs a bti_j as a target. This results
in a panic as seen below. Using x16 (or x17) with an indirect
branch keeps the target bti_c.
Bad mode in Synchronous Abort handler detected on CPU1, code 0x34000003 -- BTI
CPU: 1 PID: 265 Comm: cryptomgr_test Not tainted 5.8.11-300.fc33.aarch64 #1
pstate: 20400c05 (nzCv daif +PAN -UAO BTYPE=j-)
pc : aesbs_encrypt8+0x0/0x5f0 [aes_neon_bs]
lr : aesbs_xts_encrypt+0x48/0xe0 [aes_neon_bs]
sp : ffff80001052b730
aesbs_encrypt8+0x0/0x5f0 [aes_neon_bs]
__xts_crypt+0xb0/0x2dc [aes_neon_bs]
xts_encrypt+0x28/0x3c [aes_neon_bs]
crypto_skcipher_encrypt+0x50/0x84
simd_skcipher_encrypt+0xc8/0xe0
crypto_skcipher_encrypt+0x50/0x84
test_skcipher_vec_cfg+0x224/0x5f0
test_skcipher+0xbc/0x120
alg_test_skcipher+0xa0/0x1b0
alg_test+0x3dc/0x47c
cryptomgr_test+0x38/0x60
Fixes: 0e89640b64 ("crypto: arm64 - Use modern annotations for assembly functions")
Cc: <stable@vger.kernel.org> # 5.6.x-
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Suggested-by: Dave P Martin <Dave.Martin@arm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201006163326.2780619-1-jeremy.linton@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here are some miscellaneous rxrpc fixes:
(1) Fix the xdr encoding of the contents read from an rxrpc key.
(2) Fix a BUG() for a unsupported encoding type.
(3) Fix missing _bh lock annotations.
(4) Fix acceptance handling for an incoming call where the incoming call
is encrypted.
(5) The server token keyring isn't network namespaced - it belongs to the
server, so there's no need. Namespacing it means that request_key()
fails to find it.
(6) Fix a leak of the server keyring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We got reports from GKE customers flows being reset by netfilter
conntrack unless nf_conntrack_tcp_be_liberal is set to 1.
Traces seemed to suggest ACK packet being dropped by the
packet capture, or more likely that ACK were received in the
wrong order.
wscale=7, SYN and SYNACK not shown here.
This ACK allows the sender to send 1871*128 bytes from seq 51359321 :
New right edge of the window -> 51359321+1871*128=51598809
09:17:23.389210 IP A > B: Flags [.], ack 51359321, win 1871, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389212 IP B > A: Flags [.], seq 51422681:51424089, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 1408
09:17:23.389214 IP A > B: Flags [.], ack 51422681, win 1376, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389253 IP B > A: Flags [.], seq 51424089:51488857, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 64768
09:17:23.389272 IP A > B: Flags [.], ack 51488857, win 859, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389275 IP B > A: Flags [.], seq 51488857:51521241, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
Receiver now allows to send 606*128=77568 from seq 51521241 :
New right edge of the window -> 51521241+606*128=51598809
09:17:23.389296 IP A > B: Flags [.], ack 51521241, win 606, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389308 IP B > A: Flags [.], seq 51521241:51553625, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
It seems the sender exceeds RWIN allowance, since 51611353 > 51598809
09:17:23.389346 IP B > A: Flags [.], seq 51553625:51611353, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 57728
09:17:23.389356 IP B > A: Flags [.], seq 51611353:51618393, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 7040
09:17:23.389367 IP A > B: Flags [.], ack 51611353, win 0, options [nop,nop,TS val 10 ecr 999], length 0
netfilter conntrack is not happy and sends RST
09:17:23.389389 IP A > B: Flags [R], seq 92176528, win 0, length 0
09:17:23.389488 IP B > A: Flags [R], seq 174478967, win 0, length 0
Now imagine ACK were delivered out of order and tcp_add_backlog() sets window based on wrong packet.
New right edge of the window -> 51521241+859*128=51631193
Normally TCP stack handles OOO packets just fine, but it
turns out tcp_add_backlog() does not. It can update the window
field of the aggregated packet even if the ACK sequence
of the last received packet is too old.
Many thanks to Alexandre Ferrieux for independently reporting the issue
and suggesting a fix.
Fixes: 4f693b55c3 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexandre Ferrieux <alexandre.ferrieux@orange.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently data fin on data packet are not handled properly:
the 'rcv_data_fin_seq' field is interpreted as the last
sequence number carrying a valid data, but for data fin
packet with valid maps we currently store map_seq + map_len,
that is, the next value.
The 'write_seq' fields carries instead the value subseguent
to the last valid byte, so in mptcp_write_data_fin() we
never detect correctly the last DSS map.
Fixes: 7279da6145 ("mptcp: Use MPTCP-level flag for sending DATA_FIN")
Fixes: 1a49b2c2a5 ("mptcp: Handle incoming 32-bit DATA_FIN values")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Fix tail dropping watermarks for Ocelot switches
This series adds a missing division by 60, and a warning to prevent that
in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tail dropping is enabled for a port when:
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu_read_lock() is not supposed to lock the kernel_sendmsg() API
since it has the lock_sock() in qrtr_sendmsg() which will sleep. Hence,
fix it by excluding the locking for kernel_sendmsg().
While at it, let's also use radix_tree_deref_retry() to confirm the
validity of the pointer returned by radix_tree_deref_slot() and use
radix_tree_iter_resume() to resume iterating the tree properly before
releasing the lock as suggested by Doug.
Fixes: a7809ff90c ("net: qrtr: ns: Protect radix_tree_deref_slot() using rcu read locks")
Reported-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Alex Elder <elder@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b0dbd97de1 ("platform/x86: asus-wmi: Add support for
SW_TABLET_MODE") added support for reporting SW_TABLET_MODE using the
Asus 0x00120063 WMI-device-id to see if various transformer models were
docked into their keyboard-dock (SW_TABLET_MODE=0) or if they were
being used as a tablet.
The new SW_TABLET_MODE support (naively?) assumed that non Transformer
devices would either not support the 0x00120063 WMI-device-id at all,
or would NOT set ASUS_WMI_DSTS_PRESENCE_BIT in their reply when querying
the device-id.
Unfortunately this is not true and we have received many bug reports about
this change causing the asus-wmi driver to always report SW_TABLET_MODE=1
on non Transformer devices. This causes libinput to think that these are
360 degree hinges style 2-in-1s folded into tablet-mode. Making libinput
suppress keyboard and touchpad events from the builtin keyboard and
touchpad. So effectively this causes the keyboard and touchpad to not work
on many non Transformer Asus models.
This commit fixes this by using the existing DMI based quirk mechanism in
asus-nb-wmi.c to allow using the 0x00120063 device-id for reporting
SW_TABLET_MODE on Transformer models and ignoring it on all other models.
Fixes: b0dbd97de1 ("platform/x86: asus-wmi: Add support for SW_TABLET_MODE")
Link: https://patchwork.kernel.org/patch/11780901/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209011
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1876997
Reported-by: Samuel Čavoj <samuel@cavoj.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Pull x86 platform driver fixes from Andy Shevchenko:
"We have some fixes for Tablet Mode reporting in particular, that users
are complaining a lot about.
Summary:
- Attempt #3 of enabling Tablet Mode reporting w/o regressions
- Improve battery recognition code in ASUS WMI driver
- Fix Kconfig dependency warning for Fujitsu and LG laptop drivers
- Add fixes in Thinkpad ACPI driver for _BCL method and NVRAM polling
- Fix power supply extended topology in Mellanox driver
- Fix memory leak in OLPC EC driver
- Avoid static struct device in Intel PMC core driver
- Add support for the touchscreen found in MPMAN Converter9 2-in-1
- Update MAINTAINERS to reflect the real state of affairs"
* tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse
MAINTAINERS: Add Mark Gross and Hans de Goede as x86 platform drivers maintainers
platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting
platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"
platform/x86: intel_pmc_core: do not create a static struct device
platform/x86: mlx-platform: Fix extended topology configuration for power supply units
platform/x86: pcengines-apuv2: Fix typo on define of AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
platform/x86: fix kconfig dependency warning for FUJITSU_LAPTOP
platform/x86: fix kconfig dependency warning for LG_LAPTOP
platform/x86: thinkpad_acpi: initialize tp_nvram_state variable
platform/x86: intel-vbtn: Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360
platform/x86: asus-wmi: Add BATC battery name to the list of supported
platform/x86: asus-nb-wmi: Revert "Do not load on Asus T100TA and T200TA"
platform/x86: touchscreen_dmi: Add info for the MPMAN Converter9 2-in-1
Documentation: laptops: thinkpad-acpi: fix underline length build warning
Platform: OLPC: Fix memleak in olpc_ec_probe
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.
Fix it to return an error instead if the server key keyring is already set.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
The keyring containing the server's tokens isn't network-namespaced, so it
shouldn't be looked up with a network namespace. It is expected to be
owned specifically by the server, so namespacing is unnecessary.
Fixes: a58946c158 ("keys: Pass the network namespace into request_key mechanism")
Signed-off-by: David Howells <dhowells@redhat.com>
When a new incoming call arrives at an userspace rxrpc socket on a new
connection that has a security class set, the code currently pushes it onto
the accept queue to hold a ref on it for the socket. This doesn't work,
however, as recvmsg() pops it off, notices that it's in the SERVER_SECURING
state and discards the ref. This means that the call runs out of refs too
early and the kernel oopses.
By contrast, a kernel rxrpc socket manually pre-charges the incoming call
pool with calls that already have user call IDs assigned, so they are ref'd
by the call tree on the socket.
Change the mode of operation for userspace rxrpc server sockets to work
like this too. Although this is a UAPI change, server sockets aren't
currently functional.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
conn->state_lock may be taken in softirq mode, but a previous patch
replaced an outer lock in the response-packet event handling code, and lost
the _bh from that when doing so.
Fix this by applying the _bh annotation to the state_lock locking.
Fixes: a1399f8bb0 ("rxrpc: Call channels should have separate call number spaces")
Signed-off-by: David Howells <dhowells@redhat.com>
If rxrpc_read() (which allows KEYCTL_READ to read a key), sees a token of a
type it doesn't recognise, it can BUG in a couple of places, which is
unnecessary as it can easily get back to userspace.
Fix this to print an error message instead.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: David Howells <dhowells@redhat.com>
The session key should be encoded with just the 8 data bytes and
no length; ENCODE_DATA precedes it with a 4 byte length, which
confuses some existing tools that try to parse this format.
Add an ENCODE_BYTES macro that does not include a length, and use
it for the key. Also adjust the expected length.
Note that commit 774521f353 ("rxrpc: Fix an assertion in
rxrpc_read()") had fixed a BUG by changing the length rather than
fixing the encoding. The original length was correct.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Evaluating ACPI _BCL could fail, then ACPI buffer size will be set to 0.
When reuse this ACPI buffer, AE_BUFFER_OVERFLOW will be triggered.
Re-initialize buffer size will make ACPI evaluate successfully.
Fixes: 46445b6b89 ("thinkpad-acpi: fix handle locate for video and query of _BCL")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently, the memory containing DT is not reserved. Thus, that region
of memory can be reallocated or reused for other purposes. This may result
in corrupted DT for nommu virt board in Qemu. We may not face any issue
in kendryte as DT is embedded in the kernel image for that.
Fixes: 6bd33e1ece ("riscv: add nommu support")
Cc: stable@vger.kernel.org
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Openvswitch allows to drop a packet's Ethernet header, therefore
skb_mpls_push() and skb_mpls_pop() might be called with ethernet=true
and mac_len=0. In that case the pointer passed to skb_mod_eth_type()
doesn't point to an Ethernet header and the new Ethertype is written at
unexpected locations.
Fix this by verifying that mac_len is big enough to contain an Ethernet
header.
Fixes: fa4e0f8855 ("net/sched: fix corrupted L2 header with MPLS 'push' and 'pop' actions")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analysis reports this problem:
drivers/net/ethernet/marvell/mvneta.c:3465:2: warning:
Attempt to free released memory
kfree(txq->buf);
^~~~~~~~~~~~~~~
When mvneta_txq_sw_init() fails to alloc txq->tso_hdrs,
it frees without poisoning txq->buf. The error is caught
in the mvneta_setup_txqs() caller which handles the error
by cleaning up all of the txqs with a call to
mvneta_txq_sw_deinit which also frees txq->buf.
Since mvneta_txq_sw_deinit is a general cleaner, all of the
partial cleaning in mvneta_txq_sw_deinit()'s error handling
is not needed.
Fixes: 2adb719d74 ("net: mvneta: Implement software TSO")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we take RTNL on dump path, it is possible to
skip RTNL on insertion path. So the following race condition
is possible:
rtnl_lock() // no rtnl lock
mutex_lock(&idrinfo->lock);
// insert ERR_PTR(-EBUSY)
mutex_unlock(&idrinfo->lock);
tc_dump_action()
rtnl_unlock()
So we have to skip those temporary -EBUSY entries on dump path
too.
Reported-and-tested-by: syzbot+b47bc4f247856fb4d9e1@syzkaller.appspotmail.com
Fixes: 0fedc63fad ("net_sched: commit action insertions together")
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "i" isn't initialized back correctly after the first loop
under the label inst_rollback gets executed.
The value of "i" is assigned to be option_count - 1, and the ensuing
loop (under alloc_rollback) begins by initializing i--.
Thus, the value of i when the loop begins execution will now become
i = option_count - 2.
Thus, when kfree(dst_opts[i]) is called in the second loop in this
order, (i.e., inst_rollback followed by alloc_rollback),
dst_optsp[option_count - 2] is the first element freed, and
dst_opts[option_count - 1] does not get freed, and thus, a memory
leak is caused.
This memory leak can be fixed, by assigning i = option_count (instead of
option_count - 1).
Fixes: 80f7c6683f ("team: add support for per-port options")
Reported-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Tested-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pinned pages are not properly accounted particularly when
mapping error occurs on IOTLB update. Clean up dangling
pinned pages for the error path. As the inflight pinned
pages, specifically for memory region that strides across
multiple chunks, would need more than one free page for
book keeping and accounting. For simplicity, pin pages
for all memory in the IOVA range in one go rather than
have multiple pin_user_pages calls to make up the entire
region. This way it's easier to track and account the
pages already mapped, particularly for clean-up in the
error path.
Fixes: 4c8cf31885 ("vhost: introduce vDPA-based backend")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Link: https://lore.kernel.org/r/1601701330-16837-3-git-send-email-si-wei.liu@oracle.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the IOTLB device is enabled, the log_guest_addr that is passed by
userspace to the VHOST_SET_VRING_ADDR ioctl, and which is then written
to vq->log_addr, is a GIOVA. All writes to this address are translated
by log_user() to writes to an HVA, and then ultimately logged through
the corresponding GPAs in log_write_hva(). No logging will ever occur
with vq->log_addr in this case. It is thus wrong to pass vq->log_addr
and log_guest_addr to log_access_vq() which assumes they are actual
GPAs.
Introduce a new vq_log_used_access_ok() helper that only checks accesses
to the log for the used structure when there isn't an IOTLB device around.
Signed-off-by: Greg Kurz <groug@kaod.org>
Link: https://lore.kernel.org/r/160171933385.284610.10189082586063280867.stgit@bahia.lan
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix many (lots deleted here) build errors in hinic by selecting NET_DEVLINK.
ld: drivers/net/ethernet/huawei/hinic/hinic_hw_dev.o: in function `mgmt_watchdog_timeout_event_handler':
hinic_hw_dev.c:(.text+0x30a): undefined reference to `devlink_health_report'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x1c): undefined reference to `devlink_fmsg_u32_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x126): undefined reference to `devlink_fmsg_binary_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_hw_reporter_dump':
hinic_devlink.c:(.text+0x1ba): undefined reference to `devlink_fmsg_string_pair_put'
ld: hinic_devlink.c:(.text+0x227): undefined reference to `devlink_fmsg_u8_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_alloc':
hinic_devlink.c:(.text+0xaee): undefined reference to `devlink_alloc'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_free':
hinic_devlink.c:(.text+0xb04): undefined reference to `devlink_free'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_register':
hinic_devlink.c:(.text+0xb26): undefined reference to `devlink_register'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_unregister':
hinic_devlink.c:(.text+0xb46): undefined reference to `devlink_unregister'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_create':
hinic_devlink.c:(.text+0xb75): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xb95): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xbac): undefined reference to `devlink_health_reporter_destroy'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_destroy':
Fixes: 51ba902a16 ("net-next/hinic: Initialize hw interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bin Luo <luobin9@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Cc: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept
KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guest
Pull xen fix from Juergen Gross:
"Fix a regression introduced in 5.9-rc3 which caused a system running
as fully virtualized guest under Xen to crash when using legacy
devices like a floppy"
* tag 'for-linus-5.9b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't use chip_data for legacy IRQs
Pull USB/PHY fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 5.9-rc8
The PHY driver fix resolves an issue found by Dan Carpenter for a
memory leak.
The USB fixes fall into two groups:
- usb gadget fix from Bryan that is a fix for a previous security fix
that showed up in in-the-wild testing
- usb core driver matching bugfixes. This fixes a bug that has
plagued the both the usbip driver and syzbot testing tools this -rc
release cycle. All is now working properly so usbip connections
will work, and syzbot can get back to fuzzing USB drivers properly.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbcore/driver: Accommodate usbip
usbcore/driver: Fix incorrect downcast
usbcore/driver: Fix specific driver selection
Revert "usbip: Implement a match function to fix usbip"
USB: gadget: f_ncm: Fix NDP16 datagram validation
phy: ti: am654: Fix a leak in serdes_am654_probe()
Pull i2c fixes from Wolfram Sang:
"Some more driver fixes for i2c"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: npcm7xx: Clear LAST bit after a failed transaction.
i2c: cpm: Fix i2c_ram structure
i2c: i801: Exclude device from suspend direct complete optimization
Pull input fixes from Dmitry Torokhov:
"A couple more driver quirks, now enabling newer trackpoints from
Synaptics for real"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
Input: trackpoint - enable Synaptics trackpoints
memalloc_nocma_{save/restore} APIs can be used to skip page allocation
on CMA area, but, there is a missing case and the page on CMA area could
be allocated even if APIs are used. This patch handles this case to fix
the potential issue.
For now, these APIs are used to prevent long-term pinning on the CMA
page. When the long-term pinning is requested on the CMA page, it is
migrated to the non-CMA page before pinning. This non-CMA page is
allocated by using memalloc_nocma_{save/restore} APIs. If APIs doesn't
work as intended, the CMA page is allocated and it is pinned for a long
time. This long-term pin for the CMA page causes cma_alloc() failure
and it could result in wrong behaviour on the device driver who uses the
cma_alloc().
Missing case is an allocation from the pcplist. MIGRATE_MOVABLE pcplist
could have the pages on CMA area so we need to skip it if ALLOC_CMA
isn't specified.
Fixes: 8510e69c8e (mm/page_alloc: fix memalloc_nocma_{save/restore} APIs)
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Link: https://lkml.kernel.org/r/1601429472-12599-1-git-send-email-iamjoonsoo.kim@lge.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The routine that applies debug flags to the kmem_cache slabs
inadvertantly prevents non-debug flags from being applied to those
same objects. That is, if slub_debug=<flag>,<slab> is specified,
non-debugged slabs will end up having flags of zero, and the slabs
may be unusable.
Fix this by including the input flags for non-matching slabs with the
contents of slub_debug, so that the caches are created as expected
alongside any debugging options that may be requested. With this, we
can remove the check for a NULL slub_debug_string, since it's covered
by the loop itself.
Fixes: e17f1dfba3 ("mm, slub: extend slub_debug syntax for multiple blocks")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: https://lkml.kernel.org/r/20200930161931.28575-1-farman@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PFEC_MASK and PFEC_MATCH fields in the VMCS reverse the meaning of
the #PF intercept bit in the exception bitmap when they do not match.
This means that, if PFEC_MASK and/or PFEC_MATCH are set, the
hypervisor can get a vmexit for #PF exceptions even when the
corresponding bit is clear in the exception bitmap.
This is unexpected and is promptly detected by a WARN_ON_ONCE.
To fix it, reset PFEC_MASK and PFEC_MATCH when the #PF intercept
is disabled (as is common with enable_ept && !allow_smaller_maxphyaddr).
Reported-by: Qian Cai <cai@redhat.com>>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From: Saeed Mahameed <saeedm@nvidia.com>
====================
This series introduces some fixes to mlx5 driver.
v1->v2:
- Patch #1 Don't return while mutex is held. (Dave)
v2->v3:
- Drop patch #1, will consider a better approach (Jakub)
- use cpu_relax() instead of cond_resched() (Jakub)
- while(i--) to reveres a loop (Jakub)
- Drop old mellanox email sign-off and change the committer email
(Jakub)
Please pull and let me know if there is any problem.
For -stable v4.15
('net/mlx5e: Fix VLAN cleanup flow')
('net/mlx5e: Fix VLAN create flow')
For -stable v4.16
('net/mlx5: Fix request_irqs error flow')
For -stable v5.4
('net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU')
('net/mlx5: Avoid possible free of command entry while timeout comp handler')
For -stable v5.7
('net/mlx5e: Fix return status when setting unsupported FEC mode')
For -stable v5.8
('net/mlx5e: Fix race condition on nhe->n pointer in neigh update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Coly Li says:
====================
Introduce sendpage_ok() to detect misused sendpage in network related drivers
As Sagi Grimberg suggested, the original fix is refind to a more common
inline routine:
static inline bool sendpage_ok(struct page *page)
{
return (!PageSlab(page) && page_count(page) >= 1);
}
If sendpage_ok() returns true, the checking page can be handled by the
concrete zero-copy sendpage method in network layer.
The v10 series has 7 patches, fixes a WARN_ONCE() usage from v9 series,
- The 1st patch in this series introduces sendpage_ok() in header file
include/linux/net.h.
- The 2nd patch adds WARN_ONCE() for improper zero-copy send in
kernel_sendpage().
- The 3rd patch fixes the page checking issue in nvme-over-tcp driver.
- The 4th patch adds page_count check by using sendpage_ok() in
do_tcp_sendpages() as Eric Dumazet suggested.
- The 5th and 6th patches just replace existing open coded checks with
the inline sendpage_ok() routine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In libceph, ceph_tcp_sendpage() does the following checks before handle
the page by network layer's zero copy sendpage method,
if (page_count(page) >= 1 && !PageSlab(page))
This check is exactly what sendpage_ok() does. This patch replace the
open coded checks by sendpage_ok() as a code cleanup.
Signed-off-by: Coly Li <colyli@suse.de>
Acked-by: Jeff Layton <jlayton@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In iscsci driver, iscsi_tcp_segment_map() uses the following code to
check whether the page should or not be handled by sendpage:
if (!recv && page_count(sg_page(sg)) >= 1 && !PageSlab(sg_page(sg)))
The "page_count(sg_page(sg)) >= 1 && !PageSlab(sg_page(sg)" part is to
make sure the page can be sent to network layer's zero copy path. This
part is exactly what sendpage_ok() does.
This patch uses use sendpage_ok() in iscsi_tcp_segment_map() to replace
the original open coded checks.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chris Leech <cleech@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In _drbd_send_page() a page is checked by following code before sending
it by kernel_sendpage(),
(page_count(page) < 1) || PageSlab(page)
If the check is true, this page won't be send by kernel_sendpage() and
handled by sock_no_sendpage().
This kind of check is exactly what macro sendpage_ok() does, which is
introduced into include/linux/net.h to solve a similar send page issue
in nvme-tcp code.
This patch uses macro sendpage_ok() to replace the open coded checks to
page type and refcount in _drbd_send_page(), as a code cleanup.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab
objects") adds the checks for Slab pages, but the pages don't have
page_count are still missing from the check.
Network layer's sendpage method is not designed to send page_count 0
pages neither, therefore both PageSlab() and page_count() should be
both checked for the sending page. This is exactly what sendpage_ok()
does.
This patch uses sendpage_ok() in do_tcp_sendpages() to detect misused
.sendpage, to make the code more robust.
Fixes: a10674bf24 ("tcp: detecting the misuse of .sendpage for Slab objects")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently nvme_tcp_try_send_data() doesn't use kernel_sendpage() to
send slab pages. But for pages allocated by __get_free_pages() without
__GFP_COMP, which also have refcount as 0, they are still sent by
kernel_sendpage() to remote end, this is problematic.
The new introduced helper sendpage_ok() checks both PageSlab tag and
page_count counter, and returns true if the checking page is OK to be
sent by kernel_sendpage().
This patch fixes the page checking issue of nvme_tcp_try_send_data()
with sendpage_ok(). If sendpage_ok() returns true, send this page by
kernel_sendpage(), otherwise use sock_no_sendpage to handle this page.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Vlastimil Babka <vbabka@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If a page sent into kernel_sendpage() is a slab page or it doesn't have
ref_count, this page is improper to send by the zero copy sendpage()
method. Otherwise such page might be unexpected released in network code
path and causes impredictable panic due to kernel memory management data
structure corruption.
This path adds a WARN_ON() on the sending page before sends it into the
concrete zero-copy sendpage() method, if the page is improper for the
zero-copy sendpage() method, a warning message can be observed before
the consequential unpredictable kernel panic.
This patch does not change existing kernel_sendpage() behavior for the
improper page zero-copy send, it just provides hint warning message for
following potential panic due the kernel memory heap corruption.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Cong Wang <amwang@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original problem was from nvme-over-tcp code, who mistakenly uses
kernel_sendpage() to send pages allocated by __get_free_pages() without
__GFP_COMP flag. Such pages don't have refcount (page_count is 0) on
tail pages, sending them by kernel_sendpage() may trigger a kernel panic
from a corrupted kernel heap, because these pages are incorrectly freed
in network stack as page_count 0 pages.
This patch introduces a helper sendpage_ok(), it returns true if the
checking page,
- is not slab page: PageSlab(page) is false.
- has page refcount: page_count(page) is not zero
All drivers who want to send page to remote end by kernel_sendpage()
may use this helper to check whether the page is OK. If the helper does
not return true, the driver should try other non sendpage method (e.g.
sock_no_sendpage()) to handle the page.
Signed-off-by: Coly Li <colyli@suse.de>
Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Vlastimil Babka <vbabka@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
v2:
If reading the MAC address from eeprom fail don't throw an error, use randomly
generated MAC instead. Either way the adapter will soldier on and the return
type of set_ethernet_addr() can be reverted to void.
v1:
Fix a bug in set_ethernet_addr() which does not take into account possible
errors (or partial reads) returned by its helpers. This can potentially lead to
writing random data into device's MAC address registers.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As warned by "make htmldocs", there are two new struct elements
that aren't documented:
../include/linux/netdevice.h:2159: warning: Function parameter or member 'unlink_list' not described in 'net_device'
../include/linux/netdevice.h:2159: warning: Function parameter or member 'nested_level' not described in 'net_device'
Fixes: 1fc70edb7d ("net: core: add nested_level variable in net_device")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull pin control fixes from Linus Walleij:
"Some pin control fixes here. All of them are driver fixes, the Intel
Cherryview being the most interesting one.
- Fix a mux problem for I2C in the MVEBU driver.
- Fix a really hairy inversion problem in the Intel Cherryview
driver.
- Fix the register for the sdc2_clk in the Qualcomm SM8250 driver.
- Check the virtual GPIO boot failur in the Mediatek driver"
* tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: check mtk_is_virt_gpio input parameter
pinctrl: qcom: sm8250: correct sdc2_clk
pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
pinctrl: mvebu: Fix i2c sda definition for 98DX3236
Pull SCSI fixes from James Bottomley:
"Two patches in driver frameworks. The iscsi one corrects a bug induced
by a BPF change to network locking and the other is a regression we
introduced"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
Pull io_uring fixes from Jens Axboe:
- fix for async buffered reads if read-ahead is fully disabled (Hao)
- double poll match fix
- ->show_fdinfo() potential ABBA deadlock complaint fix
* tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
io_uring: fix async buffered reads when readahead is disabled
io_uring: fix potential ABBA deadlock in ->show_fdinfo()
io_uring: always delete double poll wait entry on match
Pull block fix from Jens Axboe:
"Single fix for a ->commit_rqs failure case"
* tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
blk-mq: call commit_rqs while list empty but error happen
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aad ("netlink: add infrastructure to expose policies to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is attached while in promiscuous mode and with VLAN
filtering turned off, both configurations are not respected and VLAN
filtering is performed.
There are 2 flows which add the any-vid rules during interface attach:
VLAN creation table and set rx mode. Each is relaying on the other to
add any-vid rules, eventually non of them does.
Fix this by adding any-vid rules on VLAN creation regardless of
promiscuous mode.
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this patch unloading an interface in promiscuous mode with RX
VLAN filtering feature turned off - resulted in a warning. This is due
to a wrong condition in the VLAN rules cleanup flow, which left the
any-vid rules in the VLAN steering table. These rules prevented
destroying the flow group and the flow table.
The any-vid rules are removed in 2 flows, but none of them remove it in
case both promiscuous is set and VLAN filtering is off. Fix the issue by
changing the condition of the VLAN table cleanup flow to clean also in
case of promiscuous mode.
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 20 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 19 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_table:2112:(pid 28729): Flow table 262149 wasn't destroyed, refcount > 1
...
...
------------[ cut here ]------------
FW pages counter is 11560 after reclaiming all pages
WARNING: CPU: 1 PID: 28729 at
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:660
mlx5_reclaim_startup_pages+0x178/0x230 [mlx5_core]
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
mlx5_function_teardown+0x2f/0x90 [mlx5_core]
mlx5_unload_one+0x71/0x110 [mlx5_core]
remove_one+0x44/0x80 [mlx5_core]
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0xfb/0x1c0
device_release_driver+0x12/0x20
pci_stop_bus_device+0x68/0x90
pci_stop_and_remove_bus_device+0x12/0x20
hv_eject_device_work+0x6f/0x170 [pci_hyperv]
? __schedule+0x349/0x790
process_one_work+0x206/0x400
worker_thread+0x34/0x3f0
? process_one_work+0x400/0x400
kthread+0x126/0x140
? kthread_park+0x90/0x90
ret_from_fork+0x22/0x30
---[ end trace 6283bde8d26170dc ]---
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Verify the configured FEC mode is supported by at least a single link
mode before applying the command. Otherwise fail the command and return
"Operation not supported".
Prior to this patch, the command was successful, yet it falsely set all
link modes to FEC auto mode - like configuring FEC mode to auto. Auto
mode is the default configuration if a link mode doesn't support the
configured FEC mode.
Fixes: b5ede32d33 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Declare GRE offload support with respect to the inner protocol. Add a
list of supported inner protocols on which the driver can offload
checksum and GSO. For other protocols, inform the stack to do the needed
operations. There is no noticeable impact on GRE performance.
Fixes: 2729984149 ("net/mlx5e: Support TSO and TX checksum offloads for GRE tunnels")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit introduced the following coverity issue at function
mlx5_tc_ct_rule_to_tuple_nat:
- Memory - corruptions (OVERRUN)
Overrunning array "tuple->ip.src_v6.in6_u.u6_addr32" of 4 4-byte
elements at element index 7 (byte offset 31) using index
"ip6_offset" (which evaluates to 7).
In case of IPv6 destination address rewrite, ip6_offset values are
between 4 to 7, which will cause memory overrun of array
"tuple->ip.src_v6.in6_u.u6_addr32" to array
"tuple->ip.dst_v6.in6_u.u6_addr32".
Fixed by writing the value directly to array
"tuple->ip.dst_v6.in6_u.u6_addr32" in case ip6_offset values are
between 4 to 7.
Fixes: bc562be967 ("net/mlx5e: CT: Save ct entries tuples in hashtables")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this fix, in Striding RQ mode the driver was vulnerable when
receiving packets in the range (stride size - headroom, stride size].
Where stride size is calculated by mtu+headroom+tailroom aligned to the
closest power of 2.
Usually, this filtering is performed by the HW, except for a few cases:
- Between 2 VFs over the same PF with different MTUs
- On bluefield, when the host physical function sets a larger MTU than
the ARM has configured on its representor and uplink representor.
When the HW filtering is not present, packets that are larger than MTU
might be harmful for the RQ's integrity, in the following impacts:
1) Overflow from one WQE to the next, causing a memory corruption that
in most cases is unharmful: as the write happens to the headroom of next
packet, which will be overwritten by build_skb(). In very rare cases,
high stress/load, this is harmful. When the next WQE is not yet reposted
and points to existing SKB head.
2) Each oversize packet overflows to the headroom of the next WQE. On
the last WQE of the WQ, where addresses wrap-around, the address of the
remainder headroom does not belong to the next WQE, but it is out of the
memory region range. This results in a HW CQE error that moves the RQ
into an error state.
Solution:
Add a page buffer at the end of each WQE to absorb the leak. Actually
the maximal overflow size is headroom but since all memory units must be
of the same size, we use page size to comply with UMR WQEs. The increase
in memory consumption is of a single page per RQ. Initialize the mkey
with all MTTs pointing to a default page. When the channels are
activated, UMR WQEs will redirect the RX WQEs to the actual memory from
the RQ's pool, while the overflow MTTs remain mapped to the default page.
Fixes: 73281b78a3 ("net/mlx5e: Derive Striding RQ size from MTU")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Increase granularity of the error path to avoid unneeded free/release.
Fix the cleanup to be symmetric to the order of creation.
Fixes: 0ddf543226 ("xdp/mlx5: setup xdp_rxq_info")
Fixes: 422d4c401e ("net/mlx5e: RX, Split WQ objects for different RQ types")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
It is possible that new command entry index allocation will temporarily
fail. The new command holds the semaphore, so it means that a free entry
should be ready soon. Add one second retry mechanism before returning an
error.
Patch "net/mlx5: Avoid possible free of command entry while timeout comp
handler" increase the possibility to bump into this temporarily failure
as it delays the entry index release for non-callback commands.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Once driver detects a command interface command timeout, it warns the
user and returns timeout error to the caller. In such case, the entry of
the command is not evacuated (because only real event interrupt is allowed
to clear command interface entry). If the HW event interrupt
of this entry will never arrive, this entry will be left unused forever.
Command interface entries are limited and eventually we can end up without
the ability to post a new command.
In addition, if driver will not consume the EQE of the lost interrupt and
rearm the EQ, no new interrupts will arrive for other commands.
Add a resiliency mechanism for manually polling the command EQ in case of
a command timeout. In case resiliency mechanism will find non-handled EQE,
it will consume it, and the command interface will be fully functional
again. Once the resiliency flow finished, wait another 5 seconds for the
command interface to complete for this command entry.
Define mlx5_cmd_eq_recover() to manage the cmd EQ polling resiliency flow.
Add an async EQ spinlock to avoid races between resiliency flows and real
interrupts that might run simultaneously.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As part of driver unload, it destroys the commands EQ (via FW command).
As the commands EQ is destroyed, FW will not generate EQEs for any command
that driver sends afterwards. Driver should poll for later commands status.
Driver commands mode metadata is updated before the commands EQ is
actually destroyed. This can lead for double completion handle by the
driver (polling and interrupt), if a command is executed and completed by
FW after the mode was changed, but before the EQ was destroyed.
Fix that by using the mlx5_cmd_allowed_opcode mechanism to guarantee
that only DESTROY_EQ command can be executed during this time period.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Pull epoll fixes from Al Viro:
"Several race fixes in epoll"
* 'work.epoll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ep_create_wakeup_source(): dentry name can change under you...
epoll: EPOLL_CTL_ADD: close the race in decision to take fast path
epoll: replace ->visited/visited_list with generation count
epoll: do not insert into poll queues until all sanity checks are done
Pull RISC-V fixes from Palmer Dabbelt:
"Two fixes for this week:
- The addition of a symbol export for clint_time_val, which has been
inlined into some timex functions and can be used by drivers.
- A fix to avoid calling get_cycles() before the timers have been
probed.
These both only effect !MMU systems"
* tag 'riscv-for-linus-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Check clint_time_val before use
clocksource: clint: Export clint_time_val for modules
Pull btrfs fixes from David Sterba:
"Two more fixes.
One is for a lockdep warning/lockup (also caught by syzbot), that one
has been seen in practice. Regarding the other syzbot reports
mentioned last time, they don't seem to be urgent and reliably
reproducible so they'll be fixed later.
The second fix is for a potential corruption when device replace
finishes and the in-memory state of trim is not copied to the new
device"
* tag 'for-5.9-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix filesystem corruption after a device replace
btrfs: move btrfs_rm_dev_replace_free_srcdev outside of all locks
btrfs: move btrfs_scratch_superblocks into btrfs_dev_replace_finishing
Pull power management fixes from Rafael Wysocki:
"These fix one more issue related to the recent RCU-lockdep changes, a
typo in documentation and add a missing return statement to
intel_pstate.
Specifics:
- Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf
Hansson)
- Fix typo in the PM documentation (Yoann Congal)
- Add return statement that is missing after recent changes in the
intel_pstate driver (Zhang Rui)"
* tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: imx6q: Fixup RCU usage for cpuidle
Documentation: PM: Fix a reStructuredText syntax error
cpufreq: intel_pstate: Fix missing return statement
Pull IIO fixes from Greg KH:
"Here are two small IIO driver fixes for 5.9-rc8 that resolve some
reported issues:
- driver name fixed in one driver
- device name typo fixed
Both have been in linux-next for a while with no reported problems"
* tag 'staging-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: qcom-spmi-adc5: fix driver name
iio: adc: ad7124: Fix typo in device name
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
Commit f227e3ec3b ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in
83bdc7275e ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
Fixes: 83bdc7275e ("random32: remove net_rand_state from the latent entropy gcc plugin")
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit ea426c2a7d ("mm: memcg: prepare for byte-sized vmstat
items") the write side of slab counters accepts a value in bytes and
converts it to pages. It happens in __mod_node_page_state().
However a non-SMP version of __mod_node_page_state() doesn't perform
this conversion. It leads to incorrect (unrealistically high) slab
counters values. Fix this by adding a similar conversion to the non-SMP
version of __mod_node_page_state().
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-and-tested-by: Bastian Bittorf <bb@npl.de>
Fixes: ea426c2a7d ("mm: memcg: prepare for byte-sized vmstat items")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Darren Hart and Andy Shevchenko lately have not had enough time to
maintain the x86 platform drivers, dropping their status to:
"Odd Fixes".
Mark Gross and Hans de Goede will take over maintainership of
the x86 platform drivers. Replace Darren and Andy's entries with
theirs and change the status to "Maintained".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2 recent commits:
cfae58ed68 ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE
on the 9 / "Laptop" chasis-type")
1fac39fd03 ("platform/x86: intel-vbtn: Also handle tablet-mode switch on
"Detachable" and "Portable" chassis-types")
Enabled reporting of SW_TABLET_MODE on more devices since the vbtn ACPI
interface is used by the firmware on some of those devices to report this.
Testing has shown that unconditionally enabling SW_TABLET_MODE reporting
on all devices with a chassis type of 8 ("Portable") or 10 ("Notebook")
which support the VGBS method is a very bad idea.
Many of these devices are normal laptops (non 2-in-1) models with a VGBS
which always returns 0, which we translate to SW_TABLET_MODE=1. This in
turn causes userspace (libinput) to suppress events from the builtin
keyboard and touchpad, making the laptop essentially unusable.
Since the problem of wrongly reporting SW_TABLET_MODE=1 in combination
with libinput, leads to a non-usable system. Where as OTOH many people will
not even notice when SW_TABLET_MODE is not being reported, this commit
changes intel_vbtn_has_switches() to use a DMI based allow-list.
The new DMI based allow-list matches on the 31 ("Convertible") and
32 ("Detachable") chassis-types, as these clearly are 2-in-1s and
so far if they support the intel-vbtn ACPI interface they all have
properly working SW_TABLET_MODE reporting.
Besides these 2 generic matches, it also contains model specific matches
for 2-in-1 models which use a different chassis-type and which are known
to have properly working SW_TABLET_MODE reporting.
This has been tested on the following 2-in-1 devices:
Dell Venue 11 Pro 7130 vPro
HP Pavilion X2 10-p002nd
HP Stream x360 Convertible PC 11
Medion E1239T
Fixes: cfae58ed68 ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type")
BugLink: https://forum.manjaro.org/t/keyboard-and-touchpad-only-work-on-kernel-5-6/22668
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1175599
Cc: Barnabás Pőcze <pobrn@protonmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The pipe splice code still used the old model of waiting for pipe IO by
using a non-specific "pipe_wait()" that waited for any pipe event to
happen, which depended on all pipe IO being entirely serialized by the
pipe lock. So by checking the state you were waiting for, and then
adding yourself to the wait queue before dropping the lock, you were
guaranteed to see all the wakeups.
Strictly speaking, the actual wakeups were not done under the lock, but
the pipe_wait() model still worked, because since the waiter held the
lock when checking whether it should sleep, it would always see the
current state, and the wakeup was always done after updating the state.
However, commit 0ddad21d3e ("pipe: use exclusive waits when reading or
writing") split the single wait-queue into two, and in the process also
made the "wait for event" code wait for _two_ wait queues, and that then
showed a race with the wakers that were not serialized by the pipe lock.
It's only splice that used that "pipe_wait()" model, so the problem
wasn't obvious, but Josef Bacik reports:
"I hit a hang with fstest btrfs/187, which does a btrfs send into
/dev/null. This works by creating a pipe, the write side is given to
the kernel to write into, and the read side is handed to a thread that
splices into a file, in this case /dev/null.
The box that was hung had the write side stuck here [pipe_write] and
the read side stuck here [splice_from_pipe_next -> pipe_wait].
[ more details about pipe_wait() scenario ]
The problem is we're doing the prepare_to_wait, which sets our state
each time, however we can be woken up either with reads or writes. In
the case above we race with the WRITER waking us up, and re-set our
state to INTERRUPTIBLE, and thus never break out of schedule"
Josef had a patch that avoided the issue in pipe_wait() by just making
it set the state only once, but the deeper problem is that pipe_wait()
depends on a level of synchonization by the pipe mutex that it really
shouldn't. And the whole "wait for any pipe state change" model really
isn't very good to begin with.
So rather than trying to work around things in pipe_wait(), remove that
legacy model of "wait for arbitrary pipe event" entirely, and actually
create functions that wait for the pipe actually being readable or
writable, and can do so without depending on the pipe lock serializing
everything.
Fixes: 0ddad21d3e ("pipe: use exclusive waits when reading or writing")
Link: https://lore.kernel.org/linux-fsdevel/bfa88b5ad6f069b2b679316b9e495a970130416c.1601567868.git.josef@toxicpanda.com/
Reported-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull iommu fixes from Joerg Roedel:
- Fix a device reference counting bug in the Exynos IOMMU driver.
- Lockdep fix for the Intel VT-d driver.
- Fix a bug in the AMD IOMMU driver which caused corruption of the IVRS
ACPI table and caused IOMMU driver initialization failures in kdump
kernels.
* tag 'iommu-fixes-v5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix lockdep splat in iommu_flush_dev_iotlb()
iommu/amd: Fix the overwritten field in IVMD header
iommu/exynos: add missing put_device() call in exynos_iommu_of_xlate()
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that system freezes on r8169 driver load on a system
using ether_clk. The original change was done under the assumption
that the clock isn't needed for basic operations like chip register
access. But obviously that was wrong.
Therefore effectively revert the original change, and in addition
leave the clock active when suspending and WoL is enabled. Chip may
not be able to process incoming packets otherwise.
Fixes: 9f0b54cd16 ("r8169: move switching optional clock on/off to pll power functions")
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull arm64 fix from Catalin Marinas:
"A previous commit to prevent AML memory opregions from accessing the
kernel memory turned out to be too restrictive. Relax the permission
check to permit the ACPI core to map kernel memory used for table
overrides"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: permit ACPI core to map kernel memory used for table overrides
Pull drm fixes from Dave Airlie:
"AMD and vmwgfx fixes.
Just dequeuing these a bit early as the AMD ones are bit larger than
I'd prefer, but Alex missed last week so it's a double set of fixes.
The larger ones are just register header fixes for the new chips that
were just introduced in rc1 along with some new PCI IDs for new hw.
Otherwise it is usual fixes.
The vmwgfx fix was due to some testing I was doing and found we
weren't booting properly, vmware had the fix internally so hurried it
vmwgfx:
- fix a regression due to TTM refactor
amdgpu:
- Fix potential double free in userptr handling
- Sienna Cichlid and Navy Flounder udpates
- Add Sienna Cichlid PCI IDs
- Drop experimental flag for navi12
- Raven fixes
- Renoir fixes
- HDCP fix
- DCN3 fix for clang and older versions of gcc
- Fix a runtime pm refcount issue"
* tag 'drm-fixes-2020-10-01-1' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: disable gfxoff temporarily for navy_flounder
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/vmwgfx: Fix error handling in get_node
drm/amd/display: remove duplicate call to rn_vbios_smu_get_smu_version()
drm/amdgpu/swsmu/smu12: fix force clock handling for mclk
drm/amdgpu: restore proper ref count in amdgpu_display_crtc_set_config
drm/amdgpu/display: fix CFLAGS setup for DCN30
drm/amd/display: fix return value check for hdcp_work
drm/amdgpu: remove gpu_info fw support for sienna_cichlid etc.
drm/amd/pm: Removed fixed clock in auto mode DPM
drm/amdgpu: remove experimental flag from navi12
drm/amdgpu: add device ID for sienna_cichlid (v2)
drm/amdgpu: use the AV1 defines for VCN 3.0
drm/amdgpu: add VCN 3.0 AV1 registers
drm/amdgpu: add the GC 10.3 VRS registers
drm/amdgpu: prevent double kfree ttm->sg
Pull tracing fixes from Steven Rostedt:
"Two tracing fixes:
- Fix temp buffer accounting that caused a WARNING for
ftrace_dump_on_opps()
- Move the recursion check in one of the function callback helpers to
the beginning of the function, as if the rcu_is_watching() gets
traced, it will cause a recursive loop that will crash the kernel"
* tag 'trace-v5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Move RCU is watching check after recursion check
tracing: Fix trace_find_next_entry() accounting of temp buffer size
Michal reported a build failure likes below:
BTFIDS vmlinux
FAILED unresolved symbol tcp_timewait_sock
make[1]: *** [/.../linux-5.9-rc7/Makefile:1176: vmlinux] Error 255
This error can be triggered when config has CONFIG_NET enabled
but CONFIG_INET disabled. In this case, there is no user of
istructs inet_timewait_sock and tcp_timewait_sock and hence
vmlinux BTF types are not generated for these two structures.
To fix the problem, let us force BTF generation for these two
structures with BTF_TYPE_EMIT.
Fixes: fce557bcef ("bpf: Make btf_sock_ids global")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20201001051339.2549085-1-yhs@fb.com
Calling pipe2() with O_NOTIFICATION_PIPE could results in memory
leaks unless watch_queue_init() is successful.
In case of watch_queue_init() failure in pipe2() we are left
with inode and pipe_inode_info instances that need to be freed. That
failure exit has been introduced in commit c73be61ced ("pipe: Add
general notification queue support") and its handling should've been
identical to nearby treatment of alloc_file_pseudo() failures - it
is dealing with the same situation. As it is, the mainline kernel
leaks in that case.
Another problem is that CONFIG_WATCH_QUEUE and !CONFIG_WATCH_QUEUE
cases are treated differently (and the former leaks just pipe_inode_info,
the latter - both pipe_inode_info and inode).
Fixed by providing a dummy wacth_queue_init() in !CONFIG_WATCH_QUEUE
case and by having failures of wacth_queue_init() handled the same way
we handle alloc_file_pseudo() ones.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Signed-off-by: Qian Cai <cai@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since commit c330fb1ddc ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.")
Xen is using the chip_data pointer for storing IRQ specific data. When
running as a HVM domain this can result in problems for legacy IRQs, as
those might use chip_data for their own purposes.
Use a local array for this purpose in case of legacy IRQs, avoiding the
double use.
Cc: stable@vger.kernel.org
Fixes: c330fb1ddc ("XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.")
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Stefan Bader <stefan.bader@canonical.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20200930091614.13660-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Commit 387caf0b75 ("iommu/amd: Treat per-device exclusion
ranges as r/w unity-mapped regions") accidentally overwrites
the 'flags' field in IVMD (struct ivmd_header) when the I/O
virtualization memory definition is associated with the
exclusion range entry. This leads to the corrupted IVMD table
(incorrect checksum). The kdump kernel reports the invalid checksum:
ACPI BIOS Warning (bug): Incorrect checksum in table [IVRS] - 0x5C, should be 0x60 (20200717/tbprint-177)
AMD-Vi: [Firmware Bug]: IVRS invalid checksum
Fix the above-mentioned issue by modifying the 'struct unity_map_entry'
member instead of the IVMD header.
Cleanup: The *exclusion_range* functions are not used anymore, so
get rid of them.
Fixes: 387caf0b75 ("iommu/amd: Treat per-device exclusion ranges as r/w unity-mapped regions")
Reported-and-tested-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200926102602.19177-1-adrianhuang0701@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Commit a0e50aa3f4 ("KVM: arm64: Factor out stage 2 page table
data from struct kvm") dropped the ISB after __load_guest_stage2(),
only leaving the one that is required when the speculative AT
workaround is in effect.
As Andrew points it: "This alternative is 'backwards' to avoid a
double ISB as there is one in __load_guest_stage2 when the workaround
is active."
Restore the missing ISB, conditionned on the AT workaround not being
active.
Fixes: a0e50aa3f4 ("KVM: arm64: Factor out stage 2 page table data from struct kvm")
Reported-by: Andrew Scull <ascull@google.com>
Reported-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When driver has been converted to the bitmap API the non-bitmap functions
started behaving differently on 32-bit BE architectures since the bytes in
two consequent unsigned longs are in different order in comparison to byte
array. Hence if the chip had had more than 32 lines the memset() call over
it would have not set up upper lines correctly.
Although it's currently a theoretical case (no supported chips of this type
has 32+ lines), it's better to provide a clean code to avoid people thinking
this is okay and potentially producing not fully working things.
Fixes: 35d13d9489 ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930142013.59247-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Geetha sowjanya says:
====================
Fix bugs in Octeontx2 netdev driver
In existing Octeontx2 network drivers code has issues
like stale entries in broadcast replication list, missing
L3TYPE for IPv6 frames, running tx queues on error and
race condition in mbox reset.
This patch set fixes the above issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mbox implementation in octeontx2 driver has three states
alloc, send and reset in mbox response. VF allocate and
sends message to PF for processing, PF ACKs them back and
reset the mbox memory. In some case we see synchronization
issue where after msgs_acked is incremented and before
mbox_reset API is called, if current execution is scheduled
out and a different thread is scheduled in which checks for
msgs_acked. Since the new thread sees msgs_acked == msgs_sent
it will try to allocate a new message and to send a new mbox
message to PF.Now if mbox_reset is scheduled in, PF will see
'0' in msgs_send.
This patch fixes the issue by calling mbox_reset before
incrementing msgs_acked flag for last processing message and
checks for valid message size.
Fixes: d424b6c02 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in otx2_open on failure of nix_lf_start
transmit queues are not stopped which are already
started in link_event. Since the tx queues are not
stopped network stack still try's to send the packets
leading to driver crash while access the device resources.
Fixes: 50fe6c02e ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TCP/UDP checksum offload feature in Octeontx2
expects L3TYPE to be set irrespective of IP header
checksum is being offloaded or not. Currently for
IPv6 frames L3TYPE is not being set resulting in
packet drop with checksum error. This patch fixes
this issue.
Fixes: 3ca6c4c88 ("octeontx2-pf: Add packet transmission support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet replication feature present in Octeontx2
is a hardware linked list of PF and its VF
interfaces so that broadcast packets are sent
to all interfaces present in the list. It is
driver job to add and delete a PF/VF interface
to/from the list when the interface is brought
up and down. This patch fixes the
npc_enadis_default_entries function to handle
broadcast replication properly if packet replication
feature is present.
Fixes: 40df309e41 ("octeontx2-af: Support to enable/disable default MCAM entries")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-09-30
This series contains updates to ice driver only.
Jake increases the wait time for firmware response as it can take longer
than the current wait time. Preserves the NVM capabilities of the device in
safe mode so the device reports its NVM update capabilities properly
when in this state.
v2: Added cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan reports that the strict policy for memory mapped by the
ACPI core breaks the use case of passing ACPI table overrides via
initramfs. This is due to the fact that the memory type used for
loading the initramfs in memory is not recognized as a memory type
that is typically used by firmware to pass firmware tables.
Since the purpose of the strict policy is to ensure that no AML or
other ACPI code can manipulate any memory that is used by the kernel
to keep its internal state or the state of user tasks, we can relax
the permission check, and allow mappings of memory that is reserved
and marked as NOMAP via memblock, and therefore not covered by the
linear mapping to begin with.
Fixes: 1583052d11 ("arm64/acpi: disallow AML memory opregions to access kernel memory")
Fixes: 325f5585ec ("arm64/acpi: disallow writeable AML opregion mapping for EFI code regions")
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20200929132522.18067-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull clk fixes from Stephen Boyd:
"Another batch of clk driver fixes:
- Make sure DRAM and ChipID region doesn't get disabled on Exynos
- Fix a SATA failure on Tegra
- Fix the emac_ptp clk divider on stratix10"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix the divider for the emac_ptp_free_clk
clk: samsung: exynos4: mark 'chipid' clock as CLK_IGNORE_UNUSED
clk: tegra: Fix missing prototype for tegra210_clk_register_emc()
clk: tegra: Always program PLL_E when enabled
clk: tegra: Capitalization fixes
clk: samsung: Keep top BPLL mux on Exynos542x enabled
The NoMMU kernel is broken for QEMU virt machine from Linux-5.9-rc6
because clint_time_val is used even before CLINT driver is probed
at following places:
1. rand_initialize() calls get_cycles() which in-turn uses
clint_time_val
2. boot_init_stack_canary() calls get_cycles() which in-turn
uses clint_time_val
The issue#1 (above) is fixed by providing custom random_get_entropy()
for RISC-V NoMMU kernel. For issue#2 (above), we remove dependency of
boot_init_stack_canary() on get_cycles() and this is aligned with the
boot_init_stack_canary() implementations of ARM, ARM64 and MIPS kernel.
Fixes: d5be89a8d1 ("RISC-V: Resurrect the MMIO timer implementation for M-mode systems")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We use a device's allocation state tree to track ranges in a device used
for allocated chunks, and we set ranges in this tree when allocating a new
chunk. However after a device replace operation, we were not setting the
allocated ranges in the new device's allocation state tree, so that tree
is empty after a device replace.
This means that a fitrim operation after a device replace will trim the
device ranges that have allocated chunks and extents, as we trim every
range for which there is not a range marked in the device's allocation
state tree. It is also important during chunk allocation, since the
device's allocation state is used to determine if a range is already
allocated when allocating a new chunk.
This is trivial to reproduce and the following script triggers the bug:
$ cat reproducer.sh
#!/bin/bash
DEV1="/dev/sdg"
DEV2="/dev/sdh"
DEV3="/dev/sdi"
wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null
# Create a raid1 test fs on 2 devices.
mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null
mount $DEV1 /mnt/btrfs
xfs_io -f -c "pwrite -S 0xab 0 10M" /mnt/btrfs/foo
echo "Starting to replace $DEV1 with $DEV3"
btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs
echo
echo "Running fstrim"
fstrim /mnt/btrfs
echo
echo "Unmounting filesystem"
umount /mnt/btrfs
echo "Mounting filesystem in degraded mode using $DEV3 only"
wipefs -a $DEV1 $DEV2 &> /dev/null
mount -o degraded $DEV3 /mnt/btrfs
if [ $? -ne 0 ]; then
dmesg | tail
echo
echo "Failed to mount in degraded mode"
exit 1
fi
echo
echo "File foo data (expected all bytes = 0xab):"
od -A d -t x1 /mnt/btrfs/foo
umount /mnt/btrfs
When running the reproducer:
$ ./replace-test.sh
wrote 10485760/10485760 bytes at offset 0
10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec)
Starting to replace /dev/sdg with /dev/sdi
Running fstrim
Unmounting filesystem
Mounting filesystem in degraded mode using /dev/sdi only
mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error.
[19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started
[19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished
[19582.208293] BTRFS info (device sdi): allowing degraded mounts
[19582.208298] BTRFS info (device sdi): disk space caching is enabled
[19582.208301] BTRFS info (device sdi): has skinny extents
[19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing
[19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed
[19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0
[19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5
[19582.231576] BTRFS error (device sdi): open_ctree failed
Failed to mount in degraded mode
So fix by setting all allocated ranges in the replace target device when
the replace operation is finishing, when we are holding the chunk mutex
and we can not race with new chunk allocations.
A test case for fstests follows soon.
Fixes: 1c11b63eff ("btrfs: replace pending/pinned chunks lists with io tree")
CC: stable@vger.kernel.org # 5.2+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The commit eb1f00237a ("lockdep,trace: Expose tracepoints"), started to
expose us for tracepoints. For imx6q cpuidle, this leads to an RCU splat
according to below.
[6.870684] [<c0db7690>] (_raw_spin_lock) from [<c011f6a4>] (imx6q_enter_wait+0x18/0x9c)
[6.878846] [<c011f6a4>] (imx6q_enter_wait) from [<c09abfb0>] (cpuidle_enter_state+0x168/0x5e4)
To fix the problem, let's assign the corresponding idlestate->flags the
CPUIDLE_FLAG_RCU_IDLE bit, which enables us to call rcu_idle_enter|exit()
at the proper point.
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a reStructuredText syntax error in the cpuidle PM admin-guide
documentation: the ``...'' quotation marks are parsed as partial ''...''
reStructuredText markup and break the output formatting.
This change them to "...".
Signed-off-by: Yoann Congal <yoann.congal@smile.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix missing return statement when writing "off" to intel_pstate status
sysfs I/F.
Fixes: 55671ea325 ("cpufreq: intel_pstate: Free memory only when turning off")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee0 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Also partially revert the follow-up change "drm: pl111: Absorb the
external register header".
This reverts the parts of commits
7e4e589db7 and
0fb8125635 that touch paths outside
of drivers/gpu/drm/pl111.
The fbdev driver is used by Android's FVP configuration. Using the
DRM driver together with DRM's fbdev emulation results in a failure
to boot Android. The root cause is that Android's generic fbdev
userspace driver relies on the ability to set the pixel format via
FBIOPUT_VSCREENINFO, which is not supported by fbdev emulation.
There have been other less critical behavioral differences identified
between the fbdev driver and the DRM driver with fbdev emulation. The
DRM driver exposes different values for the panel's width, height and
refresh rate, and the DRM driver fails a FBIOPUT_VSCREENINFO syscall
with yres_virtual greater than the maximum supported value instead
of letting the syscall succeed and setting yres_virtual based on yres.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929195344.2219796-1-pcc@google.com
gfxoff is temporarily disabled for navy_flounder, since
at present the feature caused some tdr when performing
display operations.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the dpm clock table is needed during DC HW initialization.
And that (DC HW initialization) comes before smu_late_init()
where current APU dpm clock table setup is performed. So, NULL
pointer dereference will be triggered. By moving APU dpm clock
table setup to smu_hw_init(), this can be avoided.
Fixes: 02cf91c113 ("drm/amd/powerplay: postpone operations not required for hw setup to late_init")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-29
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 14 day(s) which contain
a total of 7 files changed, 28 insertions(+), 8 deletions(-).
The main changes are:
1) fix xdp loading regression in libbpf for old kernels, from Andrii.
2) Do not discard packet when NETDEV_TX_BUSY, from Magnus.
3) Fix corner cases in libbpf related to endianness and kconfig, from Tony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clint_time_val will soon be used by the RISC-V implementation of
random_get_entropy(), which is a static inline function that may be used by
modules (at least CRYPTO_JITTERENTROPY=m).
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
ttm_mem_type_manager_func.get_node was changed to return -ENOSPC
instead of setting the node pointer to NULL. Unfortunately
vmwgfx still had two places where it was explicitly converting
-ENOSPC to 0 causing regressions. This fixes those spots by
allowing -ENOSPC to be returned. That seems to fix recent
regressions with vmwgfx.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Sigend-off-by: Roland Scheidegger <sroland@vmware.com>
Mat Martineau says:
====================
mptcp: Fix for 32-bit DATA_FIN
The main fix is contained in patch 2, and that commit message explains
the issue with not properly converting truncated DATA_FIN sequence
numbers sent by the peer.
With patch 2 adding an unlocked read of msk->ack_seq, patch 1 cleans up
access to that data with READ_ONCE/WRITE_ONCE.
This does introduce two merge conflicts with net-next, but both have
straightforward resolution. Patch 1 modifies a line that got removed in
net-next so the modification can be dropped when merging. Patch 2 will
require a trivial conflict resolution for a modified function
declaration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The peer may send a DATA_FIN mapping with either a 32-bit or 64-bit
sequence number. When a 32-bit sequence number is received for the
DATA_FIN, it must be expanded to 64 bits before comparing it to the
last acked sequence number. This expansion was missing.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/93
Fixes: 3721b9b646 ("mptcp: Track received DATA_FIN sequence number and add related helpers")
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msk->ack_seq value is sometimes read without the msk lock held, so
make proper use of READ_ONCE and WRITE_ONCE.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull devicetree fixes from Rob Herring:
- Fix handling of HOST_EXTRACFLAGS for dtc
- Several warning fixes for DT bindings
* tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
scripts/dtc: only append to HOST_EXTRACFLAGS instead of overwriting
dt-bindings: Fix 'reg' size issues in zynqmp examples
ARM: dts: bcm2835: Change firmware compatible from simple-bus to simple-mfd
dt-bindings: leds: cznic,turris-omnia-leds: fix error in binding
dt-bindings: crypto: sa2ul: fix a DT binding check warning
autofs got broken in some configurations by commit 13c164b1a1
("autofs: switch to kernel_write") because there is now an extra LSM
permission check done by security_file_permission() in rw_verify_area().
autofs is one if the few places that really does want the much more
limited __kernel_write(), because the write is an internal kernel one
that shouldn't do any user permission checks (it also doesn't need the
file_start_write/file_end_write logic, since it's just a pipe).
There are a couple of other cases like that - accounting, core dumping,
and splice - but autofs stands out because it can be built as a module.
As a result, we need to export this internal __kernel_write() function
again.
We really don't want any other module to use this, but we don't have a
"EXPORT_SYMBOL_FOR_AUTOFS_ONLY()". But we can mark it GPL-only to at
least approximate that "internal use only" for licensing.
While in this area, make autofs pass in NULL for the file position
pointer, since it's always a pipe, and we now use a NULL file pointer
for streaming file descriptors (see file_ppos() and commit 438ab720c6:
"vfs: pass ppos=NULL to .read()/.write() of FMODE_STREAM files")
This effectively reverts commits 9db9775224 ("fs: unexport
__kernel_write") and 13c164b1a1 ("autofs: switch to kernel_write").
Fixes: 13c164b1a1 ("autofs: switch to kernel_write")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kevin Brace says:
====================
via-rhine: Resume fix and other maintenance work
I use via-rhine based Ethernet regularly, and the Ethernet dying
after resume was really annoying me. I decided to take the
matter into my own hands, and came up with a fix for the Ethernet
disappearing after resume. I will also want to take over the code
maintenance work for via-rhine. The patches apply to the latest
code, but they should be backported to older kernels as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIA Technologies VT8251 South Bridge's integrated Rhine-II
Ethernet MAC comes has a PCI revision value of 0x7c. This was
verified on ASUS P5V800-VM mainboard.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rhine_resume() and rhine_suspend(), the code calls netif_running()
to see if the network interface is down or not. If it is down (i.e.,
netif_running() returning false), they will skip any housekeeping work
within the function relating to the hardware. This becomes a problem
when the hardware resumes from a standby since it is counting on
rhine_resume() to map its MMIO and power up rest of the hardware.
Not getting its MMIO remapped and rest of the hardware powered
up lead to a soft reset failure and hardware disappearance. The
solution is to map its MMIO and power up rest of the hardware inside
rhine_open() before soft reset is to be performed. This solution was
verified on ASUS P5V800-VM mainboard's integrated Rhine-II Ethernet
MAC inside VIA Technologies VT8251 South Bridge.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent attempt to fix a ref count leak in
amdgpu_display_crtc_set_config() turned out to be doing too much and
"fixed" an intended decrease as if it were a leak. Undo that part to
restore the proper balance. This is the very nature of this function
to increase or decrease the power reference count depending on the
situation.
Consequences of this bug is that the power reference would
eventually get down to 0 while the display was still in use,
resulting in that display switching off unexpectedly.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e008fa6fb4 ("drm/amdgpu: fix ref count leak in amdgpu_display_crtc_set_config")
Cc: stable@vger.kernel.org
Cc: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly handle clang and older versions of gcc.
Fixes: e77165bf7b ("drm/amd/display: Add DCN3 blocks to Makefile")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove gpu_info fw support for sienna_cichlid etc., since the
information can be retrieved from discovery binary.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building with
$ HOST_EXTRACFLAGS=-g make
the expectation is that host tools are built with debug informations.
This however doesn't happen if the Makefile assigns a new value to the
HOST_EXTRACFLAGS instead of appending to it. So use += instead of := for
the first assignment.
Fixes: e3fd9b5384 ("scripts/dtc: consolidate include path options in Makefile")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The default sizes in examples for 'reg' are 1 cell each. Fix the
incorrect sizes in zynqmp examples:
Documentation/devicetree/bindings/dma/xilinx/xlnx,zynqmp-dpdma.example.dt.yaml: example-0: dma-controller@fd4c0000:reg:0: [0, 4249616384, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:0: [0, 4249485312, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:1: [0, 4249526272, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:2: [0, 4249530368, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Documentation/devicetree/bindings/display/xlnx/xlnx,zynqmp-dpsub.example.dt.yaml: example-0: display@fd4a0000:reg:3: [0, 4249534464, 0, 4096] is too long
From schema: /usr/local/lib/python3.8/dist-packages/dtschema/schemas/reg.yaml
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: dmaengine@vger.kernel.org
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Vladimir Oltean says:
====================
More incorrect VCAP offsets for mscc_ocelot switch
This small series fixes some wrong tc-flower action fields in the
Seville and Felix DSA drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the actions are packed together in the action RAM, an incorrect
action width means that no action except the first one would behave
correctly.
The tc-flower offload has probably not been tested on this hardware
since its introduction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port mask width was larger than the actual number of ports, and
therefore, all fields following this one were also shifted by the number
of excess bits. But the driver doesn't use the REW_OP, SMAC_REPLACE_ENA
or ACL_ID bits from the action vector, so the bug was inconsequential.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch and Linux bridge will disable LRO of the interface
when this interface added to them. Now when disable the LRO, the
virtio-net csum is disable too. That drops the forwarding performance.
Fixes: a02e8964ea ("virtio-net: ethtool configurable LRO")
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull dmaengine fix from Vinod Koul:
"Fix dmatest for misconfigured channel"
* tag 'dmaengine-fix-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: dmatest: Prevent to run on misconfigured channel
Pull virtio fixes from Michael Tsirkin:
"A couple of last minute fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: fix backend feature ioctls
vhost: Fix documentation
The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.
rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.
Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net
Cc: stable@vger.kernel.org
Cc: Paul McKenney <paulmck@kernel.org>
Fixes: c68c0fa293 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The temp buffer size variable for trace_find_next_entry() was incorrectly
being updated when the size did not change. The temp buffer size should only
be updated when it is reallocated.
This is mostly an issue when used with ftrace_dump(). That's because
ftrace_dump() can not allocate a new buffer, and instead uses a temporary
buffer with a fix size. But the variable that keeps track of that size is
incorrectly updated with each call, and it could fall into the path that
would try to reallocate the buffer and produce a warning.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1601 at kernel/trace/trace.c:3548
trace_find_next_entry+0xd0/0xe0
Modules linked in [..]
CPU: 1 PID: 1601 Comm: bash Not tainted 5.9.0-rc5-test+ #521
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03
07/14/2016
RIP: 0010:trace_find_next_entry+0xd0/0xe0
Code: 40 21 00 00 4c 89 e1 31 d2 4c 89 ee 48 89 df e8 c6 9e ff ff 89 ab 54
21 00 00 5b 5d 41 5c 41 5d c3 48 63 d5 eb bf 31 c0 eb f0 <0f> 0b 48 63 d5 eb
b4 66 0f 1f 84 00 00 00 00 00 53 48 8d 8f 60 21
RSP: 0018:ffff95a4f2e8bd70 EFLAGS: 00010046
RAX: ffffffff96679fc0 RBX: ffffffff97910de0 RCX: ffffffff96679fc0
RDX: ffff95a4f2e8bd98 RSI: ffff95a4ee321098 RDI: ffffffff97913000
RBP: 0000000000000018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000046 R12: ffff95a4f2e8bd98
R13: 0000000000000000 R14: ffff95a4ee321098 R15: 00000000009aa301
FS: 00007f8565484740(0000) GS:ffff95a55aa40000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055876bd43d90 CR3: 00000000b76e6003 CR4: 00000000001706e0
Call Trace:
trace_print_lat_context+0x58/0x2d0
? cpumask_next+0x16/0x20
print_trace_line+0x1a4/0x4f0
ftrace_dump.cold+0xad/0x12c
__handle_sysrq.cold+0x51/0x126
write_sysrq_trigger+0x3f/0x4a
proc_reg_write+0x53/0x80
vfs_write+0xca/0x210
ksys_write+0x70/0xf0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f8565579487
Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa
64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff
77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffd40707948 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f8565579487
RDX: 0000000000000002 RSI: 000055876bd74de0 RDI: 0000000000000001
RBP: 000055876bd74de0 R08: 000000000000000a R09: 0000000000000001
R10: 000055876bdec280 R11: 0000000000000246 R12: 0000000000000002
R13: 00007f856564a500 R14: 0000000000000002 R15: 00007f856564a700
irq event stamp: 109958
---[ end trace 7aab5b7e51484b00 ]---
Not only fix the updating of the temp buffer, but also do not free the temp
buffer before a new buffer is allocated (there's no reason to not continue
to use the current temp buffer if an allocation fails).
Cc: stable@vger.kernel.org
Fixes: 8e99cf91b9 ("tracing: Do not allocate buffer in trace_find_next_entry() in atomic")
Reported-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Vinod writes:
phy: Second round of fixes for 5.9
*) Fix of leak in TI phy driver
* tag 'phy-fixes-2-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: ti: am654: Fix a leak in serdes_am654_probe()
The user defined label following "fallthrough" is not considered by GCC
and causes build failure.
kernel-source/include/linux/compiler_attributes.h:208:41: error: attribute
'fallthrough' not preceding a case label or default label [-Werror]
208 define fallthrough _attribute((fallthrough_))
^~~~~~~~~~~~~
Fixes: df561f6688 ("treewide: Use fallthrough pseudo-keyword")
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/bpf/20200928090023.38117-1-zhe.he@windriver.com
Blk-mq should call commit_rqs once 'bd.last != true' and no more
request will come(so virtscsi can kick the virtqueue, e.g.). We already
do that in 'blk_mq_dispatch_rq_list/blk_mq_try_issue_list_directly' while
list not empty and 'queued > 0'. However, we can seen the same scene
once the last request in list call queue_rq and return error like
BLK_STS_IOERR which will not requeue the request, and lead that list
empty but need call commit_rqs too(Or the request for virtscsi will stay
timeout until other request kick virtqueue).
We found this problem by do fsstress test with offline/online virtscsi
device repeat quickly.
Fixes: d666ba98f8 ("blk-mq: add mq_ops->commit_rqs()")
Reported-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The async buffered reads feature is not working when readahead is
turned off. There are two things to concern:
- when doing retry in io_read, not only the IOCB_WAITQ flag but also
the IOCB_NOWAIT flag is still set, which makes it goes to would_block
phase in generic_file_buffered_read() and then return -EAGAIN. After
that, the io-wq thread work is queued, and later doing the async
reads in the old way.
- even if we remove IOCB_NOWAIT when doing retry, the feature is still
not running properly, since in generic_file_buffered_read() it goes to
lock_page_killable() after calling mapping->a_ops->readpage() to do
IO, and thus causing process to sleep.
Fixes: 1a0a7853b9 ("mm: support async buffered reads in generic_file_buffered_read()")
Fixes: 3b2a4439e0 ("io_uring: get rid of kiocb_wait_page_queue_init()")
Signed-off-by: Hao Xu <haoxu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
gpio: fixes for v5.9-rc7
- fix uninitialized variable in gpio-pca953x
- enable all 160 lines and fix interrupt configuration in gpio-aspeed-gpio
- fix ast2600 bank properties in gpio-aspeed
Like all genl families ethtool_genl_family needs to not
be a straight up constant, because it's modified/initialized
by genl_register_family(). After init, however, it's only
passed to genlmsg_put() & co. therefore we can mark it
as __ro_after_init.
Since genl_family structure contains function pointers
mark this as a fix.
Fixes: 2b4a8990b7 ("ethtool: introduce ethtool netlink interface")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validation flags are missing kdoc, add it.
Fixes: ef6243acb4 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based MCT U3-A9003 USB
3.0 ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the missing .stop entry in the Belkin driver_info structure.
Fixes: e20bd60bf6 ("net: usb: asix88179_178a: Add support for the Belkin B2B128")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo says:
====================
net: core: fix a lockdep splat in the dev_addr_list.
This patchset is to avoid lockdep splat.
When a stacked interface graph is changed, netif_addr_lock() is called
recursively and it internally calls spin_lock_nested().
The parameter of spin_lock_nested() is 'dev->lower_level',
this is called subclass.
The problem of 'dev->lower_level' is that while 'dev->lower_level' is
being used as a subclass of spin_lock_nested(), its value can be changed.
So, spin_lock_nested() would be called recursively with the same
subclass value, the lockdep understands a deadlock.
In order to avoid this, a new variable is needed and it is going to be
used as a parameter of spin_lock_nested().
The first and second patch is a preparation patch for the third patch.
In the third patch, the problem will be fixed.
The first patch is to add __netdev_upper_dev_unlink().
An existed netdev_upper_dev_unlink() is renamed to
__netdev_upper_dev_unlink(). and netdev_upper_dev_unlink()
is added as an wrapper of this function.
The second patch is to add the netdev_nested_priv structure.
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
The third patch is to add a new variable 'nested_level'
into the net_device structure.
This variable will be used as a parameter of spin_lock_nested() of
dev->addr_list_lock.
Due to this variable, it can avoid lockdep splat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a new variable 'nested_level' into the net_device
structure.
This variable will be used as a parameter of spin_lock_nested() of
dev->addr_list_lock.
netif_addr_lock() can be called recursively so spin_lock_nested() is
used instead of spin_lock() and dev->lower_level is used as a parameter
of spin_lock_nested().
But, dev->lower_level value can be updated while it is being used.
So, lockdep would warn a possible deadlock scenario.
When a stacked interface is deleted, netif_{uc | mc}_sync() is
called recursively.
So, spin_lock_nested() is called recursively too.
At this moment, the dev->lower_level variable is used as a parameter of it.
dev->lower_level value is updated when interfaces are being unlinked/linked
immediately.
Thus, After unlinking, dev->lower_level shouldn't be a parameter of
spin_lock_nested().
A (macvlan)
|
B (vlan)
|
C (bridge)
|
D (macvlan)
|
E (vlan)
|
F (bridge)
A->lower_level : 6
B->lower_level : 5
C->lower_level : 4
D->lower_level : 3
E->lower_level : 2
F->lower_level : 1
When an interface 'A' is removed, it releases resources.
At this moment, netif_addr_lock() would be called.
Then, netdev_upper_dev_unlink() is called recursively.
Then dev->lower_level is updated.
There is no problem.
But, when the bridge module is removed, 'C' and 'F' interfaces
are removed at once.
If 'F' is removed first, a lower_level value is like below.
A->lower_level : 5
B->lower_level : 4
C->lower_level : 3
D->lower_level : 2
E->lower_level : 1
F->lower_level : 1
Then, 'C' is removed. at this moment, netif_addr_lock() is called
recursively.
The ordering is like this.
C(3)->D(2)->E(1)->F(1)
At this moment, the lower_level value of 'E' and 'F' are the same.
So, lockdep warns a possible deadlock scenario.
In order to avoid this problem, a new variable 'nested_level' is added.
This value is the same as dev->lower_level - 1.
But this value is updated in rtnl_unlock().
So, this variable can be used as a parameter of spin_lock_nested() safely
in the rtnl context.
Test commands:
ip link add br0 type bridge vlan_filtering 1
ip link add vlan1 link br0 type vlan id 10
ip link add macvlan2 link vlan1 type macvlan
ip link add br3 type bridge vlan_filtering 1
ip link set macvlan2 master br3
ip link add vlan4 link br3 type vlan id 10
ip link add macvlan5 link vlan4 type macvlan
ip link add br6 type bridge vlan_filtering 1
ip link set macvlan5 master br6
ip link add vlan7 link br6 type vlan id 10
ip link add macvlan8 link vlan7 type macvlan
ip link set br0 up
ip link set vlan1 up
ip link set macvlan2 up
ip link set br3 up
ip link set vlan4 up
ip link set macvlan5 up
ip link set br6 up
ip link set vlan7 up
ip link set macvlan8 up
modprobe -rv bridge
Splat looks like:
[ 36.057436][ T744] WARNING: possible recursive locking detected
[ 36.058848][ T744] 5.9.0-rc6+ #728 Not tainted
[ 36.059959][ T744] --------------------------------------------
[ 36.061391][ T744] ip/744 is trying to acquire lock:
[ 36.062590][ T744] ffff8c4767509280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_set_rx_mode+0x19/0x30
[ 36.064922][ T744]
[ 36.064922][ T744] but task is already holding lock:
[ 36.066626][ T744] ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.068851][ T744]
[ 36.068851][ T744] other info that might help us debug this:
[ 36.070731][ T744] Possible unsafe locking scenario:
[ 36.070731][ T744]
[ 36.072497][ T744] CPU0
[ 36.073238][ T744] ----
[ 36.074007][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.075290][ T744] lock(&vlan_netdev_addr_lock_key);
[ 36.076590][ T744]
[ 36.076590][ T744] *** DEADLOCK ***
[ 36.076590][ T744]
[ 36.078515][ T744] May be due to missing lock nesting notation
[ 36.078515][ T744]
[ 36.080491][ T744] 3 locks held by ip/744:
[ 36.081471][ T744] #0: ffffffff98571df0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x236/0x490
[ 36.083614][ T744] #1: ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60
[ 36.085942][ T744] #2: ffff8c476c8da280 (&bridge_netdev_addr_lock_key/4){+...}-{2:2}, at: dev_uc_sync+0x39/0x80
[ 36.088400][ T744]
[ 36.088400][ T744] stack backtrace:
[ 36.089772][ T744] CPU: 6 PID: 744 Comm: ip Not tainted 5.9.0-rc6+ #728
[ 36.091364][ T744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 36.093630][ T744] Call Trace:
[ 36.094416][ T744] dump_stack+0x77/0x9b
[ 36.095385][ T744] __lock_acquire+0xbc3/0x1f40
[ 36.096522][ T744] lock_acquire+0xb4/0x3b0
[ 36.097540][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.098657][ T744] ? rtmsg_ifinfo+0x1f/0x30
[ 36.099711][ T744] ? __dev_notify_flags+0xa5/0xf0
[ 36.100874][ T744] ? rtnl_is_locked+0x11/0x20
[ 36.101967][ T744] ? __dev_set_promiscuity+0x7b/0x1a0
[ 36.103230][ T744] _raw_spin_lock_bh+0x38/0x70
[ 36.104348][ T744] ? dev_set_rx_mode+0x19/0x30
[ 36.105461][ T744] dev_set_rx_mode+0x19/0x30
[ 36.106532][ T744] dev_set_promiscuity+0x36/0x50
[ 36.107692][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.108929][ T744] dev_set_promiscuity+0x1e/0x50
[ 36.110093][ T744] br_port_set_promisc+0x1f/0x40 [bridge]
[ 36.111415][ T744] br_manage_promisc+0x8b/0xe0 [bridge]
[ 36.112728][ T744] __dev_set_promiscuity+0x123/0x1a0
[ 36.113967][ T744] ? __hw_addr_sync_one+0x23/0x50
[ 36.115135][ T744] __dev_set_rx_mode+0x68/0x90
[ 36.116249][ T744] dev_uc_sync+0x70/0x80
[ 36.117244][ T744] dev_uc_add+0x50/0x60
[ 36.118223][ T744] macvlan_open+0x18e/0x1f0 [macvlan]
[ 36.119470][ T744] __dev_open+0xd6/0x170
[ 36.120470][ T744] __dev_change_flags+0x181/0x1d0
[ 36.121644][ T744] dev_change_flags+0x23/0x60
[ 36.122741][ T744] do_setlink+0x30a/0x11e0
[ 36.123778][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.124929][ T744] ? __nla_validate_parse.part.6+0x45/0x8e0
[ 36.126309][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.127457][ T744] __rtnl_newlink+0x546/0x8e0
[ 36.128560][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.129623][ T744] ? deactivate_slab.isra.85+0x6a1/0x850
[ 36.130946][ T744] ? __lock_acquire+0x92c/0x1f40
[ 36.132102][ T744] ? lock_acquire+0xb4/0x3b0
[ 36.133176][ T744] ? is_bpf_text_address+0x5/0xe0
[ 36.134364][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.135445][ T744] ? rcu_read_lock_sched_held+0x32/0x60
[ 36.136771][ T744] ? kmem_cache_alloc_trace+0x2d8/0x380
[ 36.138070][ T744] ? rtnl_newlink+0x2e/0x70
[ 36.139164][ T744] rtnl_newlink+0x47/0x70
[ ... ]
Fixes: 845e0ebb44 ("net: change addr_list_lock back to static key")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev_upper_dev_unlink() has to work differently according to flags.
This idea is the same with __netdev_upper_dev_link().
In the following patches, new flags will be added.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TC actions call tcf_action_check_ctrlact() to validate
goto chain, so this check in tcf_action_init_1() is actually
redundant. Remove it to save troubles of leaking memory.
Fixes: e49d8c22f1 ("net_sched: defer tcf_idr_insert() in tcf_action_init_1()")
Reported-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user-space software manages fdb entries externally it should
set the ext_learn flag which marks the fdb entry as externally managed
and avoids expiring it (they're treated as static fdbs). Unfortunately
on events where fdb entries are flushed (STP down, netlink fdb flush
etc) these fdbs are also deleted automatically by the bridge. That in turn
causes trouble for the managing user-space software (e.g. in MLAG setups
we lose remote fdb entries on port flaps).
These entries are completely externally managed so we should avoid
automatically deleting them, the only exception are offloaded entries
(i.e. BR_FDB_ADDED_BY_EXT_LEARN + BR_FDB_OFFLOADED). They are flushed as
before.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-09-28
1) Fix a build warning in ip_vti if CONFIG_IPV6 is not set.
From YueHaibing.
2) Restore IPCB on espintcp before handing the packet to xfrm
as the information there is still needed.
From Sabrina Dubroca.
3) Fix pmtu updating for xfrm interfaces.
From Sabrina Dubroca.
4) Some xfrm state information was not cloned with xfrm_do_migrate.
Fixes to clone the full xfrm state, from Antony Antony.
5) Use the correct address family in xfrm_state_find. The struct
flowi must always be interpreted along with the original
address family. This got lost over the years.
Fix from Herbert Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 530b5affc6 ("spi: fsl-dspi: fix use-after-free in remove
path") this driver causes a kernel oops:
[ 1.891065] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000080
[..]
[ 2.056973] Call trace:
[ 2.059425] dspi_setup+0xc8/0x2e0
[ 2.062837] spi_setup+0xcc/0x248
[ 2.066160] spi_add_device+0xb4/0x198
[ 2.069918] of_register_spi_device+0x250/0x370
[ 2.074462] spi_register_controller+0x4f4/0x770
[ 2.079094] dspi_probe+0x5bc/0x7b0
[ 2.082594] platform_drv_probe+0x5c/0xb0
[ 2.086615] really_probe+0xec/0x3c0
[ 2.090200] driver_probe_device+0x60/0xc0
[ 2.094308] device_driver_attach+0x7c/0x88
[ 2.098503] __driver_attach+0x60/0xe8
[ 2.102263] bus_for_each_dev+0x7c/0xd0
[ 2.106109] driver_attach+0x2c/0x38
[ 2.109692] bus_add_driver+0x194/0x1f8
[ 2.113538] driver_register+0x6c/0x128
[ 2.117385] __platform_driver_register+0x50/0x60
[ 2.122105] fsl_dspi_driver_init+0x24/0x30
[ 2.126302] do_one_initcall+0x54/0x2d0
[ 2.130149] kernel_init_freeable+0x1ec/0x258
[ 2.134520] kernel_init+0x1c/0x120
[ 2.138018] ret_from_fork+0x10/0x34
[ 2.141606] Code: 97e0b11d aa0003f3 b4000680 f94006e0 (f9404000)
[ 2.147723] ---[ end trace 26cf63e6cbba33a8 ]---
This is because since this commit, the allocation of the drivers private
data is done explicitly and in this case spi_alloc_master() won't set the
correct pointer.
Also move the platform_set_drvdata() to have both next to each other.
Fixes: 530b5affc6 ("spi: fsl-dspi: fix use-after-free in remove path")
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200928085500.28254-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- NFSv4.2: copy_file_range needs to invalidate caches on success
- NFSv4.2: Fix security label length not being reset
- pNFS/flexfiles: Ensure we initialise the mirror bsizes correctly
on read
- pNFS/flexfiles: Fix signed/unsigned type issues with mirror
indices"
* tag 'nfs-for-5.9-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS/flexfiles: Be consistent about mirror index types
pNFS/flexfiles: Ensure we initialise the mirror bsizes correctly on read
NFSv4.2: fix client's attribute cache management for copy_file_range
nfs: Fix security label length not being reset
It seems likely this block was pasted from internal_get_user_pages_fast,
which is not passed an mm struct and therefore uses current's. But
__get_user_pages_locked is passed an explicit mm, and current->mm is not
always valid. This was hit when being called from i915, which uses:
pin_user_pages_remote->
__get_user_pages_remote->
__gup_longterm_locked->
__get_user_pages_locked
Before, this would lead to an OOPS:
BUG: kernel NULL pointer dereference, address: 0000000000000064
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
CPU: 10 PID: 1431 Comm: kworker/u33:1 Tainted: P S U O 5.9.0-rc7+ #140
Hardware name: LENOVO 20QTCTO1WW/20QTCTO1WW, BIOS N2OET47W (1.34 ) 08/06/2020
Workqueue: i915-userptr-acquire __i915_gem_userptr_get_pages_worker [i915]
RIP: 0010:__get_user_pages_remote+0xd7/0x310
Call Trace:
__i915_gem_userptr_get_pages_worker+0xc8/0x260 [i915]
process_one_work+0x1ca/0x390
worker_thread+0x48/0x3c0
kthread+0x114/0x130
ret_from_fork+0x1f/0x30
CR2: 0000000000000064
This commit fixes the problem by using the mm pointer passed to the
function rather than the bogus one in current.
Fixes: 008cfe4418 ("mm: Introduce mm_struct.has_pinned")
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Harald Arnesen <harald@skogtun.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current binding for the RPi firmware uses the simple-bus compatible as
a fallback to benefit from its automatic probing of child nodes.
However, simple-bus also comes with some constraints, like having the ranges,
our case.
Let's switch to simple-mfd that provides the same probing logic without
those constraints.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200924082642.18144-1-maxime@cerno.tech
Signed-off-by: Rob Herring <robh@kernel.org>
The original commit appears to have the logic reversed in
amd_fch_gpio_get_direction. Also confirmed by observing the value of
"direction" in the sys tree.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Fixes: e09d168f13 ("gpio: AMD G-Series PCH gpio driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver.
Fixes: a7a92cf815 ("r8169: sync PCIe PHY init with vendor driver 8.047.01")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlxsw_sp_acl_tcam_group_id_get() fails, the mutex initialized earlier
is not destroyed.
Fix this by initializing the mutex after calling the function. This is
symmetric to mlxsw_sp_acl_tcam_group_del().
Fixes: 5ec2ee28d2 ("mlxsw: spectrum_acl: Introduce a mutex to guard region list updates")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:
ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a HW issue, in some scenarios the LAST bit might remain set.
This will cause an unexpected NACK after reading 16 bytes on the next
read.
Example: if user tries to read from a missing device, get a NACK,
then if the next command is a long read ( > 16 bytes),
the master will stop reading after 16 bytes.
To solve this, if a command fails, check if LAST bit is still
set. If it does, reset the module.
Fixes: 56a1485b10 (i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver)
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver subfolder files refer parent folder includes in an
absolute manner.
Makefile contains a -I for this, but apparently that does not
work if object tree is separated.
Adding srctree to fix that.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.
Fixes: 39344a8962 ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the driver_info and usb ids of the AX88179 based Toshiba USB 3.0
ethernet adapter.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
bonding/team: basic dev->needed_headroom support
Both bonding and team drivers support non-ethernet devices,
but missed proper dev->needed_headroom initializations.
syzbot found a crash caused by bonding, I mirrored the fix in team as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices set needed_headroom. If we ignore it, we might
end up crashing in various skb_push() for example in ipgre_header()
since some layers assume enough headroom has been reserved.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start also "phy state machine", with UP state as it should be,
the phy_start() has to be used, in another case machine even is not
triggered. After this change negotiation is supposed to be triggered
by SM workqueue.
It's not correct usage, but it appears after the following patch,
so add it as a fix.
Fixes: 74a992b359 ("net: phy: add phy_check_link_status")
Signed-off-by: Ivan Khoronzhuk <ikhoronz@cisco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
Removing the second call of clk_disable_unprepare() in
intel_eth_pci_remove().
Fixes: 09f012e64e ("stmmac: intel: Fix clock handling on error and remove paths")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the inner
offload capability is to be restrictued to UDP tunnels.
This patch fixes the issue for non-udp tunnels by adding features
check capability and filtering appropriate features for non-udp tunnels.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-09-25
This series contains updates to the iavf and ice driver.
Sylwester fixes a crash with iavf resume due to getting the wrong pointers.
Ani fixes a call trace in ice resume by calling pci_save_state().
Jakes fixes memory leaks in case of register_netdev() failure or
ice_cfg_vsi_lan() failure for the ice driver.
v2: Rebased; no other changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for v5.9
Second, and last, set of fixes for v5.9. Only one important regression
fix for mt76.
mt76
* fix a regression in aggregation which appeared after mac80211 changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit reverts commit 7a2f2974f2 ("usbip: Implement a match
function to fix usbip").
In summary, commit d5643d2249 ("USB: Fix device driver race")
inadvertently broke usbip functionality, which I resolved in an incorrect
manner by introducing a match function to usbip, usbip_match(), that
unconditionally returns true.
However, the usbip_match function, as is, causes usbip to take over
virtual devices used by syzkaller for USB fuzzing, which is a regression
reported by Andrey Konovalov.
Furthermore, in conjunction with the fix of another bug, handled by another
patch titled "usbcore/driver: Fix specific driver selection" in this patch
set, the usbip_match function causes unexpected USB subsystem behaviour
when the usbip_host driver is loaded. The unexpected behaviour can be
qualified as follows:
- If commit 41160802ab8e ("USB: Simplify USB ID table match") is included
in the kernel, then all USB devices are bound to the usbip_host
driver, which appears to the user as if all USB devices were
disconnected.
- If the same commit (41160802ab8e) is not in the kernel (as is the case
with v5.8.10) then all USB devices are re-probed and re-bound to their
original device drivers, which appears to the user as a disconnection
and re-connection of USB devices.
Please note that this commit will make usbip non-operational again,
until yet another patch in this patch set is merged, titled
"usbcore/driver: Accommodate usbip".
Cc: <stable@vger.kernel.org> # 5.8: 41160802ab8e: USB: Simplify USB ID table match
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to move the closing of the src_device out of all the device
replace locking, but we definitely want to zero out the superblock
before we commit the last time to make sure the device is properly
removed. Handle this by pushing btrfs_scratch_superblocks into
btrfs_dev_replace_finishing, and then later on we'll move the src_device
closing and freeing stuff where we need it to be.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly
release memory associated with the VSI rings. If we had used devres
allocations for the rings, this would be ok. However, we use kzalloc and
kfree_rcu for these ring structures.
Using the correct label to cleanup the rings during ice_vsi_setup
highlights an issue in the ice_vsi_clear_rings function: it can leave
behind stale ring pointers in the q_vectors structure.
When releasing rings, we must also ensure that no q_vector associated
with the VSI will point to this ring again. To resolve this, loop over
all q_vectors and release their ring mapping. Because we are about to
free all rings, no q_vector should remain pointing to any of the rings
in this VSI.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.
This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.
An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs
Fixes: 3a858ba392 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It appears that the ice_suspend flow is missing a call to pci_save_state
and this is triggering the message "State of device not saved by
ice_suspend" and a call trace. Fix it.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When calling iavf_resume there was a crash because wrong
function was used to get iavf_adapter and net_device pointers.
Changed how iavf_resume is getting iavf_adapter and net_device
pointers from pci_dev.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
syzbot has reported an issue in the framebuffer layer, where a malicious
user may overflow our built-in font data buffers.
In order to perform a reliable range check, subsystems need to know
`FONTDATAMAX` for each built-in font. Unfortunately, our font descriptor,
`struct console_font` does not contain `FONTDATAMAX`, and is part of the
UAPI, making it infeasible to modify it.
For user-provided fonts, the framebuffer layer resolves this issue by
reserving four extra words at the beginning of data buffers. Later,
whenever a function needs to access them, it simply uses the following
macros:
Recently we have gathered all the above macros to <linux/font.h>. Let us
do the same thing for built-in fonts, prepend four extra words (including
`FONTDATAMAX`) to their data buffers, so that subsystems can use these
macros for all fonts, no matter built-in or user-provided.
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h".
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?id=08b8be45afea11888776f897895aef9ad1c3ecfd
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/ef18af00c35fb3cc826048a5f70924ed6ddce95b.1600953813.git.yepeilin.cs@gmail.com
The struct flowi must never be interpreted by itself as its size
depends on the address family. Therefore it must always be grouped
with its original family value.
In this particular instance, the original family value is lost in
the function xfrm_state_find. Therefore we get a bogus read when
it's coupled with the wrong family which would occur with inter-
family xfrm states.
This patch fixes it by keeping the original family value.
Note that the same bug could potentially occur in LSM through
the xfrm_state_pol_flow_match hook. I checked the current code
there and it seems to be safe for now as only secid is used which
is part of struct flowi_common. But that API should be changed
so that so that we don't get new bugs in the future. We could
do that by replacing fl with just secid or adding a family field.
Reported-by: syzbot+577fbac3145a6eb2e7a5@syzkaller.appspotmail.com
Fixes: 48b8d78315 ("[XFRM]: State selection update to use inner...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Currently, we use length of DSACKed range to compute number of
delivered packets. And if sequence range in DSACK is corrupted,
we can get bogus dsacked/acked count, and bogus cwnd.
This patch put bounds on DSACKed range to skip update of data
delivery and spurious retransmission information, if the DSACK
is unlikely caused by sender's action:
- DSACKed range shouldn't be greater than maximum advertised rwnd.
- Total no. of DSACKed segments shouldn't be greater than total
no. of retransmitted segs. Unlike spurious retransmits, network
duplicates or corrupted DSACKs shouldn't be counted as delivery.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe. On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present. Since 0f183fd151 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.
Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.
Fixes: edecfa98f6 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should also be regarded as an error when hw return status=4 for PF's
setting mac cmd. Only if PF return status=4 to VF should this cmd be
taken special treatment.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1.
Move the lapb_register/lapb_unregister calls into the ndo_open/ndo_stop
functions.
This makes the LAPB protocol start/stop when the network interface
starts/stops. When the network interface is down, the LAPB protocol
shouldn't be running and the LAPB module shoudn't be generating control
frames.
2.
Move netif_start_queue/netif_stop_queue into the ndo_open/ndo_stop
functions.
This makes the TX queue start/stop when the network interface
starts/stops.
(netif_stop_queue was originally in the ndo_stop function. But to make
the code look better, I created a new function to use as ndo_stop, and
made it call the original ndo_stop function. I moved netif_stop_queue
from the original ndo_stop function to the new ndo_stop function.)
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
net_sched: fix a UAF in tcf_action_init()
This patchset fixes a use-after-free triggered by syzbot. Please
find more details in each patch description.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot is able to trigger a failure case inside the loop in
tcf_action_init(), and when this happens we clean up with
tcf_action_destroy(). But, as these actions are already inserted
into the global IDR, other parallel process could free them
before tcf_action_destroy(), then we will trigger a use-after-free.
Fix this by deferring the insertions even later, after the loop,
and committing all the insertions in a separate loop, so we will
never fail in the middle of the insertions any more.
One side effect is that the window between alloction and final
insertion becomes larger, now it is more likely that the loop in
tcf_del_walker() sees the placeholder -EBUSY pointer. So we have
to check for error pointer in tcf_del_walker().
Reported-and-tested-by: syzbot+2287853d392e4b42374a@syzkaller.appspotmail.com
Fixes: 0190c1d452 ("net: sched: atomically check-allocate action")
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TC actions call tcf_idr_insert() for new action at the end
of their ->init(), so we can actually move it to a central place
in tcf_action_init_1().
And once the action is inserted into the global IDR, other parallel
process could free it immediately as its refcnt is still 1, so we can
not fail after this, we need to move it after the goto action
validation to avoid handling the failure case after insertion.
This is found during code review, is not directly triggered by syzbot.
And this prepares for the next patch.
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression in libbpf, introduced by XDP link change, which causes XDP
programs to fail to be loaded into kernel due to specified BPF_XDP
expected_attach_type. While kernel doesn't enforce expected_attach_type for
BPF_PROG_TYPE_XDP, some old kernels already support XDP program, but they
don't yet recognize expected_attach_type field in bpf_attr, so setting it to
non-zero value causes program load to fail.
Luckily, libbpf already has a mechanism to deal with such cases, so just make
expected_attach_type optional for XDP programs.
Fixes: dc8698cac7 ("libbpf: Add support for BPF XDP link")
Reported-by: Nikita Shirokov <tehnerd@tehnerd.com>
Reported-by: Udip Pant <udippant@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200924171705.3803628-1-andriin@fb.com
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200923052442.24141-1-nbd@nbd.name
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe7 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix topology configuration for power supply units in structure
'mlxplat_mlxcpld_ext_pwr_items_data', due to hardware change.
Note: no need to backport the fix, since there is no such hardware yet
(equipped with four power) at the filed.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When FUJITSU_LAPTOP is enabled and NEW_LEDS is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for LEDS_CLASS
Depends on [n]: NEW_LEDS [=n]
Selected by [y]:
- FUJITSU_LAPTOP [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && INPUT [=y] && BACKLIGHT_CLASS_DEVICE [=y] && (ACPI_VIDEO [=n] || ACPI_VIDEO [=n]=n)
The reason is that FUJITSU_LAPTOP selects LEDS_CLASS without depending on
or selecting NEW_LEDS while LEDS_CLASS is subordinate to NEW_LEDS.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: d89bcc83e7 ("platform/x86: fujitsu-laptop: select LEDS_CLASS")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When LG_LAPTOP is enabled and NEW_LEDS is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for LEDS_CLASS
Depends on [n]: NEW_LEDS [=n]
Selected by [y]:
- LG_LAPTOP [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && ACPI_WMI [=y] && INPUT [=y]
The reason is that LG_LAPTOP selects LEDS_CLASS without depending on or
selecting NEW_LEDS while LEDS_CLASS is subordinate to NEW_LEDS.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: dbf0c5a6b1 ("platform/x86: Add LG Gram laptop special features driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
clang static analysis flags this represenative problem
thinkpad_acpi.c:2523:7: warning: Branch condition evaluates
to a garbage value
if (!oldn->mute ||
^~~~~~~~~~~
In hotkey_kthread() mute is conditionally set by hotkey_read_nvram()
but unconditionally checked by hotkey_compare_and_issue_event().
So the tp_nvram_state variable s[2] needs to be initialized.
Fixes: 01e88f2598 ("ACPI: thinkpad-acpi: add CMOS NVRAM polling for hot keys (v9)")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit cfae58ed68 ("platform/x86: intel-vbtn: Only blacklist
SW_TABLET_MODE on the 9 / "Laptop" chasis-type") restored SW_TABLET_MODE
reporting on the HP stream x360 11 series on which it was previously broken
by commit de9647efea ("platform/x86: intel-vbtn: Only activate tablet
mode switch on 2-in-1's").
It turns out that enabling SW_TABLET_MODE reporting on devices with a
chassis-type of 10 ("Notebook") causes SW_TABLET_MODE to always report 1
at boot on the HP Pavilion 11 x360, which causes libinput to disable the
kbd and touchpad.
The HP Pavilion 11 x360's ACPI VGBS method sets bit 4 instead of bit 6 when
NOT in tablet mode at boot. Inspecting all the DSDTs in my DSDT collection
shows only one other model, the Medion E1239T ever setting bit 4 and it
always sets this together with bit 6.
So lets treat bit 4 as a second bit which when set indicates the device not
being in tablet-mode, as we already do for bit 6.
While at it also prefix all VGBS constant defines with "VGBS_".
Fixes: cfae58ed68 ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Intel Atom Cherry Trail platform reports a new battery
name (BATC). Tested on ASUS Transformer Mini T103HAF.
Signed-off-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The WMI INIT method on for some reason turns on the camera LED on these
2-in-1s, without the WMI interface allowing further control over the LED.
To fix this commit b5f7311d3a ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA") added a blacklist with these 2 models on it
since the WMI driver did not add any extra functionality to these models.
Recently I've been working on making more 2-in-1 models report their
tablet-mode (SW_TABLET_MODE) to userspace; and I've found that these 2
Asus models report this through WMI. This commit reverts the adding
of the blacklist, so that the Asus WMI driver can be used on these
models to report their tablet-mode. I have another patch fixing the LED
issue in a different manner.
Note this is the second time the we revert the adding of the
asus_nb_wmi_blacklist. It was reverted before in commit:
aab9e7896e ("platform/x86: asus-nb-wmi: Revert "Do not load on Asus
T100TA and T200TA")"
But some how (accidentally re-applying of the patch?) it got re-added
again in commit 3bd12da7f5 ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA"), so now we need to revert it again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add touchscreen info for the MPMAN Converter9 2-in-1. This device uses the
same case as the ITworks TW891, but it uses a different digitizer, so it
needs its own firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit 653055b9ac ("vhost-vdpa: support get/set backend features")
introduces two malfunction backend features ioctls:
1) the ioctls was blindly added to vring ioctl instead of vdpa device
ioctl
2) vhost_set_backend_features() was called when dev mutex has already
been held which will lead a deadlock
This patch fixes the above issues.
Cc: Eli Cohen <elic@nvidia.com>
Reported-by: Zhu Lingshan <lingshan.zhu@intel.com>
Fixes: 653055b9ac ("vhost-vdpa: support get/set backend features")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200907104343.31141-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When devm_regulator_register() fails, ec should be
freed just like when olpc_ec_cmd() fails.
Fixes: 231c0c2161 ("Platform: OLPC: Add a regulator for the DCON")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58a ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX DMA channel data is accessed by the xrx200_start_xmit() and the
xrx200_tx_housekeeping() function from different threads. Make sure the
accesses are synchronized by acquiring the netif_tx_lock() in the
xrx200_tx_housekeeping() function too. This lock is acquired by the
kernel before calling xrx200_start_xmit().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update kernel-doc line comments to fix warnings reported by make W=1.
net/switchdev/switchdev.c:413: warning: Function parameter or
member 'extack' not described in 'call_switchdev_notifiers'
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1838d6c62f.
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425a ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a DATA_FIN MPTCP option on a TCP FIN packet, the DATA_FIN
information would be stored but the MPTCP worker did not get
scheduled. In turn, the MPTCP socket state would remain in
TCP_ESTABLISHED and no blocked operations would be awakened.
TCP FIN packets are seen by the MPTCP socket when moving skbs out of the
subflow receive queues, so schedule the MPTCP worker when a skb with
DATA_FIN but no data payload is moved from a subflow queue. Other cases
(DATA_FIN on a bare TCP ACK or on a packet with data payload) are
already handled.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/84
Fixes: 43b54c6ee3 ("mptcp: Use full MPTCP-level disconnect state machine")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b57177 ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull Tegra clk driver fixes from Thierry Reding:
This is a set of small fixes for the Tegra clock driver.
* tag 'for-5.10-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Fix missing prototype for tegra210_clk_register_emc()
clk: tegra: Always program PLL_E when enabled
clk: tegra: Capitalization fixes
commit 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
2nd set of IIO fixes for the 5.9 cycle.
One of these fixes a regresison introduced this cycle, but if I am too late
sending this request, it can be queued up for the merge window.
ad7124: fix typo in device name exposed through sysfs.
qcom-spmi-adc: fix stray .c in driver name field.
* tag 'iio-fixes-for-5.9b-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: qcom-spmi-adc5: fix driver name
iio: adc: ad7124: Fix typo in device name
Andy reported that commit 6b41030fdc ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc ("dmaengine: dmatest: Restore default for channel")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gpio fixes for v5.9-rc6
- fix the interrupt configuration in gpio-tc35894
- explicitly support only threaded irqs in gpio-siox
- fix a resource leak in error path in gpio-mockup
- fix line event handling in syscall compatible mode in GPIO chardev
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Code in btf__parse_raw() fails to detect raw BTF of non-native endianness
and assumes it must be ELF data, which then fails to parse as ELF and
yields a misleading error message:
root:/# bpftool btf dump file /sys/kernel/btf/vmlinux
libbpf: failed to get EHDR from /sys/kernel/btf/vmlinux
For example, this could occur after cross-compiling a BTF-enabled kernel
for a target with non-native endianness, which is currently unsupported.
Check for correct endianness and emit a clearer error message:
root:/# bpftool btf dump file /sys/kernel/btf/vmlinux
libbpf: non-native BTF endianness is not supported
Fixes: 94a1fedd63 ("libbpf: Add btf__parse_raw() and generic btf__parse() APIs")
Signed-off-by: Tony Ambardar <Tony.Ambardar@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/90f81508ecc57bc0da318e0fe0f45cfe49b17ea7.1600417359.git.Tony.Ambardar@gmail.com
Include the Tegra driver's clk.h to pull in the prototype definition for
this function so that compilers don't warn about it being missing.
Fixes: 0ac65fc946 ("clk: tegra: Implement Tegra210 EMC clock")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
added checks to avoid enabling PLLs that have already been enabled by
the bootloader. However, the PLL_E configuration inherited from the
bootloader isn't necessarily the one that is needed for the kernel.
This can cause SATA to fail like this:
[ 5.310270] phy phy-sata.6: phy poweron failed --> -110
[ 5.315604] tegra-ahci 70027000.sata: failed to power on AHCI controller: -110
[ 5.323022] tegra-ahci: probe of 70027000.sata failed with error -110
Fix this by always programming the PLL_E. This ensures that any mis-
configuration by the bootloader will be overwritten by the kernel.
Fixes: bff1cef5f2 ("clk: tegra: Don't enable already enabled PLLs")
Reported-by: LABBE Corentin <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c79 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
While it is true that reading from an unmirrored source always uses
index 0, that is no longer true for mirrored sources when we fail over.
Fixes: 563c53e73b ("NFS: Fix flexfiles read failover")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
The introduced line event handling ABI in the commit
61f922db72 ("gpio: userspace ABI for reading GPIO line events")
missed the fact that 64-bit kernel may serve for 32-bit applications.
In such case the very first check in the lineevent_read() will fail
due to alignment differences.
To workaround this introduce lineevent_get_size() helper which returns actual
size of the structure in user space.
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In the skb Tx path, transmission of a packet is performed with
dev_direct_xmit(). When NETDEV_TX_BUSY is set in the drivers, it
signifies that it was not possible to send the packet right now,
please try later. Unfortunately, the xsk transmit code discarded the
packet and returned EBUSY to the application. Fix this unnecessary
packet loss, by not discarding the packet in the Tx ring and return
EAGAIN. As EAGAIN is returned to the application, it can then retry
the send operation later and the packet will then likely be sent as
the driver will then likely have space/resources to send the packet.
In summary, EAGAIN tells the application that the packet was not
discarded from the Tx ring and that it needs to call send()
again. EBUSY, on the other hand, signifies that the packet was not
sent and discarded from the Tx ring. The application needs to put
the packet on the Tx ring again if it wants it to be sent.
Fixes: 35fcde7f8d ("xsk: support for Tx")
Reported-by: Arkadiusz Zema <A.Zema@falconvsystems.com>
Suggested-by: Arkadiusz Zema <A.Zema@falconvsystems.com>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/bpf/1600257625-2353-1-git-send-email-magnus.karlsson@gmail.com
After client is done with the COPY operation, it needs to invalidate
its pagecache (as it did no reading or writing of the data locally)
and it needs to invalidate it's attributes just like it would have
for a read on the source file and write on the destination file.
Once the linux server started giving out read delegations to
read+write opens, the destination file of the copy_file range
started having delegations and not doing syncup on close of the
file leading to xfstest failures for generic/430,431,432,433,565.
v2: changing cache_validity needs to be protected by the i_lock.
Reported-by: Murphy Zhou <jencce.kernel@gmail.com>
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
nfs_readdir_page_filler() iterates over entries in a directory, reusing
the same security label buffer, but does not reset the buffer's length.
This causes decode_attr_security_label() to return -ERANGE if an entry's
security label is longer than the previous one's. This error, in
nfs4_decode_dirent(), only gets passed up as -EAGAIN, which causes another
failed attempt to copy into the buffer. The second error is ignored and
the remaining entries do not show up in ls, specifically the getdents64()
syscall.
Reproduce by creating multiple files in NFS and giving one of the later
files a longer security label. ls will not see that file nor any that are
added afterwards, though they will exist on the backend.
In nfs_readdir_page_filler(), reset security label buffer length before
every reuse
Signed-off-by: Jeffrey Mitchell <jeffrey.mitchell@starlab.io>
Fixes: b4487b9354 ("nfs: Fix getxattr kernel panic and memory overflow")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Pull a Samsung clk driver fix from Sylwester Nawrocki:
- fix for a regression in v5.9-rc1 on Odroid XU3/XU4, i.e. booting
failure due to the DRAM controller root clock being disabled
* tag 'v5.9-clk-samsung-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Keep top BPLL mux on Exynos542x enabled
Checking for the lack of epitems refering to the epoll we want to insert into
is not enough; we might have an insertion of that epoll into another one that
has already collected the set of files to recheck for excessive reverse paths,
but hasn't gotten to creating/inserting the epitem for it.
However, any such insertion in progress can be detected - it will update the
generation count in our epoll when it's done looking through it for files
to check. That gets done under ->mtx of our epoll and that allows us to
detect that safely.
We are *not* holding epmutex here, so the generation count is not stable.
However, since both the update of ep->gen by loop check and (later)
insertion into ->f_ep_link are done with ep->mtx held, we are fine -
the sequence is
grab epmutex
bump loop_check_gen
...
grab tep->mtx // 1
tep->gen = loop_check_gen
...
drop tep->mtx // 2
...
grab tep->mtx // 3
...
insert into ->f_ep_link
...
drop tep->mtx // 4
bump loop_check_gen
drop epmutex
and if the fastpath check in another thread happens for that
eventpoll, it can come
* before (1) - in that case fastpath is just fine
* after (4) - we'll see non-empty ->f_ep_link, slow path
taken
* between (2) and (3) - loop_check_gen is stable,
with ->mtx providing barriers and we end up taking slow path.
Note that ->f_ep_link emptiness check is slightly racy - we are protected
against insertions into that list, but removals can happen right under us.
Not a problem - in the worst case we'll end up taking a slow path for
no good reason.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be35 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
DT binding check produces a warning about bad cell size:
Documentation/devicetree/bindings/crypto/ti,sa2ul.example.dt.yaml: example-0: crypto@4e00000:reg:0: [0, 81788928, 0, 4608] is too long
From schema: python3.6/site-packages/dtschema/schemas/reg.yaml
Fix this by reducing the address sizes for the example to 1 cell from
current 2.
Fixes: 2ce9a7299b ("dt-bindings: crypto: Add TI SA2UL crypto accelerator documentation")
Reported-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200825133106.21542-2-t-kristo@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
The root bus checks rework in d84c572de1 ("PCI: rockchip: Use
pci_is_root_bus() to check if bus is root bus") caused a regression whereby
in rockchip_pcie_valid_device() if the bus parameter is the root bus and
the dev value == 0, the function should return 1 (ie true) without checking
if the bus->parent pointer is a root bus because that triggers a NULL
pointer dereference.
Fix this by streamlining the root bus detection.
Fixes: d84c572de1 ("PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus")
Link: https://lore.kernel.org/r/20200904140904.944-1-lorenzo.pieralisi@arm.com
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Tested-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
When we clone state only add_time was cloned. It missed values like
bytes, packets. Now clone the all members of the structure.
v1->v3:
- use memcpy to copy the entire structure
Fixes: 80c9abaabf ("[XFRM]: Extension for dynamic update of endpoint address(es)")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
XFRMA_SEC_CTX was not cloned from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- return -ENOMEM on error
v2->v3:
- fix return type to int
Fixes: 80c9abaabf ("[XFRM]: Extension for dynamic update of endpoint address(es)")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
XFRMA_REPLAY_ESN_VAL was not cloned completely from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- move curleft cloning to a separate patch
Fixes: af2f464e32 ("xfrm: Assign esn pointers when cloning a state")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
XFRMA_SET_MARK and XFRMA_SET_MARK_MASK was not cloned from the old
to the new. Migrate these two attributes during XFRMA_MSG_MIGRATE
Fixes: 9b42c1f179 ("xfrm: Extend the output_mark to support input direction and masking.")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
xfrm interfaces currently test for !skb->ignore_df when deciding
whether to update the pmtu on the skb's dst. Because of this, no pmtu
exception is created when we do something like:
ping -s 1438 <dest>
By dropping this check, the pmtu exception will be created and the
next ping attempt will work.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Fix warnings for omap_gpio_resume and omap_gpio_suspend
defined but not used when PM is disabled as noticed when
doing make randconfig builds.
Fixes: f02a03985d ("gpio: omap: Add missing PM ops for suspend")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Xiumei reported a bug with espintcp over IPv6 in transport mode,
because xfrm6_transport_finish expects to find IP6CB data (struct
inet6_skb_cb). Currently, espintcp zeroes the CB, but the relevant
part is actually preserved by previous layers (first set up by tcp,
then strparser only zeroes a small part of tcp_skb_tb), so we can just
relocate it to the start of skb->cb.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
If CONFIG_INET_XFRM_TUNNEL is set but CONFIG_IPV6 is n,
net/ipv4/ip_vti.c:493:27: warning: 'vti_ipip6_handler' defined but not used [-Wunused-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2020-08-08 08:17:22 +02:00
344 changed files with 4428 additions and 1797 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
