Pull RISC-V fixes from Paul Walmsley:
"Three fixes for RISC-V:
- Don't free and reuse memory containing the code that CPUs parked at
boot reside in.
- Fix rv64 build problems for ubsan and some modules by adding
logical and arithmetic shift helpers for 128-bit values. These are
from libgcc and are similar to what's present for ARM64.
- Fix vDSO builds to clean up their own temporary files"
* tag 'riscv/for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Less inefficient gcc tishift helpers (and export their symbols)
riscv: delete temporary files
riscv: make sure the cores stay looping in .Lsecondary_park
Pull networking fixes from David Miller:
1) Fix non-blocking connect() in x25, from Martin Schiller.
2) Fix spurious decryption errors in kTLS, from Jakub Kicinski.
3) Netfilter use-after-free in mtype_destroy(), from Cong Wang.
4) Limit size of TSO packets properly in lan78xx driver, from Eric
Dumazet.
5) r8152 probe needs an endpoint sanity check, from Johan Hovold.
6) Prevent looping in tcp_bpf_unhash() during sockmap/tls free, from
John Fastabend.
7) hns3 needs short frames padded on transmit, from Yunsheng Lin.
8) Fix netfilter ICMP header corruption, from Eyal Birger.
9) Fix soft lockup when low on memory in hns3, from Yonglong Liu.
10) Fix NTUPLE firmware command failures in bnxt_en, from Michael Chan.
11) Fix memory leak in act_ctinfo, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
cxgb4: reject overlapped queues in TC-MQPRIO offload
cxgb4: fix Tx multi channel port rate limit
net: sched: act_ctinfo: fix memory leak
bnxt_en: Do not treat DSN (Digital Serial Number) read failure as fatal.
bnxt_en: Fix ipv6 RFS filter matching logic.
bnxt_en: Fix NTUPLE firmware command failures.
net: systemport: Fixed queue mapping in internal ring map
net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec
net: dsa: sja1105: Don't error out on disabled ports with no phy-mode
net: phy: dp83867: Set FORCE_LINK_GOOD to default after reset
net: hns: fix soft lockup when there is not enough memory
net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()
net/sched: act_ife: initalize ife->metalist earlier
netfilter: nat: fix ICMP header corruption on ICMP errors
net: wan: lapbether.c: Use built-in RCU list checking
netfilter: nf_tables: fix flowtable list del corruption
netfilter: nf_tables: fix memory leak in nf_tables_parse_netdev_hooks()
netfilter: nf_tables: remove WARN and add NLA_STRING upper limits
netfilter: nft_tunnel: ERSPAN_VERSION must not be null
netfilter: nft_tunnel: fix null-attribute check
...
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd6 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8e ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing __lshrti3 was really inefficient, and the other two helpers
are also needed to compile some modules.
Add the missing versions, and export all of the symbols like arm64
already does.
This code is based on the assembly generated by libgcc builds.
This fixes a build break triggered by ubsan:
riscv64-unknown-linux-gnu-ld: lib/ubsan.o: in function `.L2':
ubsan.c:(.text.unlikely+0x38): undefined reference to `__ashlti3'
riscv64-unknown-linux-gnu-ld: ubsan.c:(.text.unlikely+0x42): undefined reference to `__ashrti3'
Signed-off-by: Olof Johansson <olof@lixom.net>
[paul.walmsley@sifive.com: use SYM_FUNC_{START,END} instead of
ENTRY/ENDPROC; note libgcc origin]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull MTD fixes from Miquel Raynal:
"Raw NAND:
- GPMI: Fix the suspend/resume
SPI-NOR:
- Fix quad enable on Spansion like flashes
- Fix selection of 4-byte addressing opcodes on Spansion"
* tag 'mtd/fixes-for-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: gpmi: Restore nfc timing setup after suspend/resume
mtd: rawnand: gpmi: Fix suspend/resume problem
mtd: spi-nor: Fix quad enable for Spansion like flashes
mtd: spi-nor: Fix selection of 4-byte addressing opcodes on Spansion
Pull drm fixes from Dave Airlie:
"Back from LCA2020, fixes wasn't too busy last week, seems to have
quieten down appropriately, some amdgpu, i915, then a core mst fix and
one fix for virtio-gpu and one for rockchip:
core mst:
- serialize down messages and clear timeslots are on unplug
amdgpu:
- Update golden settings for renoir
- eDP fix
i915:
- uAPI fix: Remove dash and colon from PMU names to comply with
tools/perf
- Fix for include file that was indirectly included
- Two fixes to make sure VMA are marked active for error capture
virtio:
- maintain obj reservation lock when submitting cmds
rockchip:
- increase link rate var size to accommodate rates"
* tag 'drm-fixes-2020-01-19' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Reorder detect_edp_sink_caps before link settings read.
drm/amdgpu: update goldensetting for renoir
drm/dp_mst: Have DP_Tx send one msg at a time
drm/dp_mst: clear time slots for ports invalid
drm/i915/pmu: Do not use colons or dashes in PMU names
drm/rockchip: fix integer type used for storing dp data rate
drm/i915/gt: Mark ring->vma as active while pinned
drm/i915/gt: Mark context->state vma as active while pinned
drm/i915/gt: Skip trying to unbind in restore_ggtt_mappings
drm/i915: Add missing include file <linux/math64.h>
drm/virtio: add missing virtio_gpu_array_lock_resv call
Temporary files used in the VDSO build process linger on even after make
mrproper: vdso-dummy.o.tmp, vdso.so.dbg.tmp.
Delete them once they're no longer needed.
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- a resctrl fix for uninitialized objects found by debugobjects
- a resctrl memory leak fix
- fix the unintended re-enabling of the of SME and SEV CPU flags if
memory encryption was disabled at bootup via the MSR space"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Ensure clearing of SME/SEV features is maintained
x86/resctrl: Fix potential memory leak
x86/resctrl: Fix an imbalance in domain_remove_cpu()
Pull timer fixes from Ingo Molnar:
"Three fixes: fix link failure on Alpha, fix a Sparse warning and
annotate/robustify a lockless access in the NOHZ code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/sched: Annotate lockless access to last_jiffies_update
lib/vdso: Make __cvdso_clock_getres() static
time/posix-stubs: Provide compat itimer supoprt for alpha
Pull cpu/SMT fix from Ingo Molnar:
"Fix a build bug on CONFIG_HOTPLUG_SMT=y && !CONFIG_SYSFS kernels"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/SMT: Fix x86 link error without CONFIG_SYSFS
Pull x86 RAS fix from Ingo Molnar:
"Fix a thermal throttling race that can result in easy to trigger boot
crashes on certain Ice Lake platforms"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce/therm_throt: Do not access uninitialized therm_work
Pull perf fixes from Ingo Molnar:
"Tooling fixes, three Intel uncore driver fixes, plus an AUX events fix
uncovered by the perf fuzzer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Remove PCIe3 unit for SNR
perf/x86/intel/uncore: Fix missing marker for snr_uncore_imc_freerunning_events
perf/x86/intel/uncore: Add PCI ID of IMC for Xeon E3 V5 Family
perf: Correctly handle failed perf_get_aux_event()
perf hists: Fix variable name's inconsistency in hists__for_each() macro
perf map: Set kmap->kmaps backpointer for main kernel map chunks
perf report: Fix incorrectly added dimensions as switch perf data file
tools lib traceevent: Fix memory leakage in filter_event
Pull locking fixes from Ingo Molnar:
"Three fixes:
- Fix an rwsem spin-on-owner crash, introduced in v5.4
- Fix a lockdep bug when running out of stack_trace entries,
introduced in v5.4
- Docbook fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Fix kernel crash when spinning on RWSEM_OWNER_UNKNOWN
futex: Fix kernel-doc notation warning
locking/lockdep: Fix buffer overrun problem in stack_trace[]
Pull irq fix from Ingo Molnar:
"Fix a recent regression in the Ingenic SoCs irqchip driver that floods
the syslog"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Get rid of the legacy IRQ domain
Pull EFI fixes from Ingo Molnar:
"Three EFI fixes:
- Fix a slow-boot-scrolling regression but making sure we use WC for
EFI earlycon framebuffer mappings on x86
- Fix a mixed EFI mode boot crash
- Disable paging explicitly before entering startup_32() in mixed
mode bootup"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efistub: Disable paging at mixed mode entry
efi/libstub/random: Initialize pointer variables to zero for mixed mode
efi/earlycon: Fix write-combine mapping on x86
Pull rseq fixes from Ingo Molnar:
"Two rseq bugfixes:
- CLONE_VM !CLONE_THREAD didn't work properly, the kernel would end
up corrupting the TLS of the parent. Technically a change in the
ABI but the previous behavior couldn't resonably have been relied
on by applications so this looks like a valid exception to the ABI
rule.
- Make the RSEQ_FLAG_UNREGISTER ABI behavior consistent with the
handling of other flags. This is not thought to impact any
applications either"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Unregister rseq for clone CLONE_VM
rseq: Reject unknown flags on rseq unregister
Pull thread fixes from Christian Brauner:
"Here is an urgent fix for ptrace_may_access() permission checking.
Commit 69f594a389 ("ptrace: do not audit capability check when
outputing /proc/pid/stat") introduced the ability to opt out of audit
messages for accesses to various proc files since they are not
violations of policy.
While doing so it switched the check from ns_capable() to
has_ns_capability{_noaudit}(). That means it switched from checking
the subjective credentials (ktask->cred) of the task to using the
objective credentials (ktask->real_cred). This is appears to be wrong.
ptrace_has_cap() is currently only used in ptrace_may_access() And is
used to check whether the calling task (subject) has the
CAP_SYS_PTRACE capability in the provided user namespace to operate on
the target task (object). According to the cred.h comments this means
the subjective credentials of the calling task need to be used.
With this fix we switch ptrace_has_cap() to use security_capable() and
thus back to using the subjective credentials.
As one example where this might be particularly problematic, Jann
pointed out that in combination with the upcoming IORING_OP_OPENAT{2}
feature, this bug might allow unprivileged users to bypass the
capability checks while asynchronously opening files like /proc/*/mem,
because the capability checks for this would be performed against
kernel credentials.
To illustrate on the former point about this being exploitable: When
io_uring creates a new context it records the subjective credentials
of the caller. Later on, when it starts to do work it creates a kernel
thread and registers a callback. The callback runs with kernel creds
for ktask->real_cred and ktask->cred.
To prevent this from becoming a full-blown 0-day io_uring will call
override_cred() and override ktask->cred with the subjective
credentials of the creator of the io_uring instance. With
ptrace_has_cap() currently looking at ktask->real_cred this override
will be ineffective and the caller will be able to open arbitray proc
files as mentioned above.
Luckily, this is currently not exploitable but would be so once
IORING_OP_OPENAT{2} land in v5.6. Let's fix it now.
To minimize potential regressions I successfully ran the criu
testsuite. criu makes heavy use of ptrace() and extensively hits
ptrace_may_access() codepaths and has a good change of detecting any
regressions.
Additionally, I succesfully ran the ptrace and seccomp kernel tests"
* tag 'for-linus-2020-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
ptrace: reintroduce usage of subjective credentials in ptrace_has_cap()
Pull s390 fixes from Vasily Gorbik:
- Fix printing misleading Secure-IPL enabled message when it is not.
- Fix a race condition between host ap bus and guest ap bus doing
device reset in crypto code.
- Fix sanity check in CCA cipher key function (CCA AES cipher key
support), which fails otherwise.
* tag 's390-5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/setup: Fix secure ipl message
s390/zcrypt: move ap device reset from bus to driver code
s390/zcrypt: Fix CCA cipher key gen with clear key value function
Pull SCSI fixes from James Bottomley:
"Three fixes in drivers with no impact to core code.
The mptfusion fix is enormous because the driver API had to be
rethreaded to pass down the necessary iocp pointer, but once that's
done a significant chunk of code is deleted.
The other two patches are small"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mptfusion: Fix double fetch bug in ioctl
scsi: storvsc: Correctly set number of hardware queues for IDE disk
scsi: fnic: fix invalid stack access
Pull char/misc fixes from Greg KH:
"Here are some small fixes for 5.5-rc7
Included here are:
- two lkdtm fixes
- coresight build fix
- Documentation update for the hw process document
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Add Amazon contact for embargoed hardware issues
lkdtm/bugs: fix build error in lkdtm_UNSET_SMEP
lkdtm/bugs: Make double-fault test always available
coresight: etm4x: Fix unused function warning
Pull staging and IIO driver fixes from Greg KH:
"Here are some small staging and iio driver fixes for 5.5-rc7
All of them are for some small reported issues. Nothing major, full
details in the shortlog.
All have been in linux-next with no reported issues"
* tag 'staging-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: ni_routes: allow partial routing information
staging: comedi: ni_routes: fix null dereference in ni_find_route_source()
iio: light: vcnl4000: Fix scale for vcnl4040
iio: buffer: align the size of scan bytes to size of the largest element
iio: chemical: pms7003: fix unmet triggered buffer dependency
iio: imu: st_lsm6dsx: Fix selection of ST_LSM6DS3_ID
iio: adc: ad7124: Fix DT channel configuration
Pull USB driver fixes from Greg KH:
"Here are some small USB driver and core fixes for 5.5-rc7
There's one fix for hub wakeup issues and a number of small usb-serial
driver fixes and device id updates.
The hub fix has been in linux-next for a while with no reported
issues, and the usb-serial ones have all passed 0-day with no
problems"
* tag 'usb-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: quatech2: handle unbound ports
USB: serial: keyspan: handle unbound ports
USB: serial: io_edgeport: add missing active-port sanity check
USB: serial: io_edgeport: handle unbound ports on URB completion
USB: serial: ch341: handle unbound port at reset_resume
USB: serial: suppress driver bind attributes
USB: serial: option: add support for Quectel RM500Q in QDL mode
usb: core: hub: Improved device recognition on remote wakeup
USB: serial: opticon: fix control-message timeouts
USB: serial: option: Add support for Quectel RM500Q
USB: serial: simple: Add Motorola Solutions TETRA MTP3xxx and MTP85xx
Michael Chan says:
====================
bnxt_en: Bug fixes.
3 small bug fix patches. The 1st two are aRFS fixes and the last one
fixes a fatal driver load failure on some kernels without PCIe
extended config space support enabled.
Please also queue these for -stable. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69f594a389 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
introduced the ability to opt out of audit messages for accesses to various
proc files since they are not violations of policy. While doing so it
somehow switched the check from ns_capable() to
has_ns_capability{_noaudit}(). That means it switched from checking the
subjective credentials of the task to using the objective credentials. This
is wrong since. ptrace_has_cap() is currently only used in
ptrace_may_access() And is used to check whether the calling task (subject)
has the CAP_SYS_PTRACE capability in the provided user namespace to operate
on the target task (object). According to the cred.h comments this would
mean the subjective credentials of the calling task need to be used.
This switches ptrace_has_cap() to use security_capable(). Because we only
call ptrace_has_cap() in ptrace_may_access() and in there we already have a
stable reference to the calling task's creds under rcu_read_lock() there's
no need to go through another series of dereferences and rcu locking done
in ns_capable{_noaudit}().
As one example where this might be particularly problematic, Jann pointed
out that in combination with the upcoming IORING_OP_OPENAT feature, this
bug might allow unprivileged users to bypass the capability checks while
asynchronously opening files like /proc/*/mem, because the capability
checks for this would be performed against kernel credentials.
To illustrate on the former point about this being exploitable: When
io_uring creates a new context it records the subjective credentials of the
caller. Later on, when it starts to do work it creates a kernel thread and
registers a callback. The callback runs with kernel creds for
ktask->real_cred and ktask->cred. To prevent this from becoming a
full-blown 0-day io_uring will call override_cred() and override
ktask->cred with the subjective credentials of the creator of the io_uring
instance. With ptrace_has_cap() currently looking at ktask->real_cred this
override will be ineffective and the caller will be able to open arbitray
proc files as mentioned above.
Luckily, this is currently not exploitable but will turn into a 0-day once
IORING_OP_OPENAT{2} land in v5.6. Fix it now!
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Jann Horn <jannh@google.com>
Fixes: 69f594a389 ("ptrace: do not audit capability check when outputing /proc/pid/stat")
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc38 ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull io_uring fixes form Jens Axboe:
- Ensure ->result is always set when IO is retried (Bijan)
- In conjunction with the above, fix a regression in polled IO issue
when retried (me/Bijan)
- Don't setup async context for read/write fixed, otherwise we may
wrongly map the iovec on retry (me)
- Cancel io-wq work if we fail getting mm reference (me)
- Ensure dependent work is always initialized correctly (me)
- Only allow original task to submit IO, don't allow it from a passed
ring fd (me)
* tag 'io_uring-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
io_uring: only allow submit from owning task
io_uring: ensure workqueue offload grabs ring mutex for poll list
io_uring: clear req->result always before issuing a read/write request
io_uring: be consistent in assigning next work from handler
io-wq: cancel work if we fail getting a mm reference
io_uring: don't setup async context for read/write fixed
Pull btrfs fixes from David Sterba:
"A few more fixes that have been in the works during last twp weeks.
All have a user visible effect and are stable material:
- scrub: properly update progress after calling cancel ioctl, calling
'resume' would start from the beginning otherwise
- fix subvolume reference removal, after moving out of the original
path the reference is not recognized and will lead to transaction
abort
- fix reloc root lifetime checks, could lead to crashes when there's
subvolume cleaning running in parallel
- fix memory leak when quotas get disabled in the middle of extent
accounting
- fix transaction abort in case of balance being started on degraded
mount on eg. RAID1"
* tag 'for-5.5-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: check rw_devices, not num_devices for balance
Btrfs: always copy scrub arguments back to user space
btrfs: relocation: fix reloc_root lifespan and access
btrfs: fix memory leak in qgroup accounting
btrfs: do not delete mismatched root refs
btrfs: fix invalid removal of root ref
btrfs: rework arguments of btrfs_unlink_subvol
Johan writes:
USB-serial fixes for 5.5-rc7
Here are a few fixes for issues related to unbound port devices which
could lead to NULL-pointer dereferences. Notably the bind attributes for
usb-serial (port) drivers are removed as almost none of the drivers can
handle individual ports going away once they've been bound.
Included are also some new device ids.
All but the unbound-port fixes have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: handle unbound ports
USB: serial: keyspan: handle unbound ports
USB: serial: io_edgeport: add missing active-port sanity check
USB: serial: io_edgeport: handle unbound ports on URB completion
USB: serial: ch341: handle unbound port at reset_resume
USB: serial: suppress driver bind attributes
USB: serial: option: add support for Quectel RM500Q in QDL mode
USB: serial: opticon: fix control-message timeouts
USB: serial: option: Add support for Quectel RM500Q
USB: serial: simple: Add Motorola Solutions TETRA MTP3xxx and MTP85xx
Pull fuse fix from Miklos Szeredi:
"Fix a regression in the last release affecting the ftp module of the
gvfs filesystem"
* tag 'fuse-fixes-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix fuse_send_readpages() in the syncronous read case
Pull sound fixes from Takashi Iwai:
"This became bigger than I have hoped for rc7. But, the only large LOC
is for stm32 fixes that are simple rewriting of register access
helpers, while the rest are all nice and small fixes:
- A few ASoC fixes for the remaining probe error handling bugs
- ALSA sequencer core fix for racy proc file accesses
- Revert the option rename of snd-hda-intel to make compatible again
- Various device-specific fixes"
* tag 'sound-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix racy access for queue timer in proc read
ALSA: usb-audio: fix sync-ep altsetting sanity check
ASoC: msm8916-wcd-digital: Reset RX interpolation path after use
ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1
ASoC: cros_ec_codec: Make the device acpi compatible
ASoC: sti: fix possible sleep-in-atomic
ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1
ASoC: hdac_hda: Fix error in driver removal after failed probe
ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers
ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP
ALSA: dice: fix fallback from protocol extension into limited functionality
ALSA: firewire-tascam: fix corruption due to spin lock without restoration in SoftIRQ context
ALSA: hda: Rename back to dmic_detect option
ASoC: stm32: dfsdm: fix 16 bits record
ASoC: stm32: sai: fix possible circular locking
ASoC: Fix NULL dereference at freeing
ASoC: Intel: bytcht_es8316: Fix Irbis NB41 netbook quirk
ASoC: rt5640: Fix NULL dereference on module unload
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # 3.5
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e10 ("USB Serial Keyspan: add support for USA-49WG & USA-28XG")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after resume")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The fstest btrfs/154 reports
[ 8675.381709] BTRFS: Transaction aborted (error -28)
[ 8675.383302] WARNING: CPU: 1 PID: 31900 at fs/btrfs/block-group.c:2038 btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.390925] CPU: 1 PID: 31900 Comm: btrfs Not tainted 5.5.0-rc6-default+ #935
[ 8675.392780] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
[ 8675.395452] RIP: 0010:btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.402672] RSP: 0018:ffffb2090888fb00 EFLAGS: 00010286
[ 8675.404413] RAX: 0000000000000000 RBX: ffff92026dfa91c8 RCX: 0000000000000001
[ 8675.406609] RDX: 0000000000000000 RSI: ffffffff8e100899 RDI: ffffffff8e100971
[ 8675.408775] RBP: ffff920247c61660 R08: 0000000000000000 R09: 0000000000000000
[ 8675.410978] R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffe4
[ 8675.412647] R13: ffff92026db74000 R14: ffff920247c616b8 R15: ffff92026dfbc000
[ 8675.413994] FS: 00007fd5e57248c0(0000) GS:ffff92027d800000(0000) knlGS:0000000000000000
[ 8675.416146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8675.417833] CR2: 0000564aa51682d8 CR3: 000000006dcbc004 CR4: 0000000000160ee0
[ 8675.419801] Call Trace:
[ 8675.420742] btrfs_start_dirty_block_groups+0x355/0x480 [btrfs]
[ 8675.422600] btrfs_commit_transaction+0xc8/0xaf0 [btrfs]
[ 8675.424335] reset_balance_state+0x14a/0x190 [btrfs]
[ 8675.425824] btrfs_balance.cold+0xe7/0x154 [btrfs]
[ 8675.427313] ? kmem_cache_alloc_trace+0x235/0x2c0
[ 8675.428663] btrfs_ioctl_balance+0x298/0x350 [btrfs]
[ 8675.430285] btrfs_ioctl+0x466/0x2550 [btrfs]
[ 8675.431788] ? mem_cgroup_charge_statistics+0x51/0xf0
[ 8675.433487] ? mem_cgroup_commit_charge+0x56/0x400
[ 8675.435122] ? do_raw_spin_unlock+0x4b/0xc0
[ 8675.436618] ? _raw_spin_unlock+0x1f/0x30
[ 8675.438093] ? __handle_mm_fault+0x499/0x740
[ 8675.439619] ? do_vfs_ioctl+0x56e/0x770
[ 8675.441034] do_vfs_ioctl+0x56e/0x770
[ 8675.442411] ksys_ioctl+0x3a/0x70
[ 8675.443718] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 8675.445333] __x64_sys_ioctl+0x16/0x20
[ 8675.446705] do_syscall_64+0x50/0x210
[ 8675.448059] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 8675.479187] BTRFS: error (device vdb) in btrfs_create_pending_block_groups:2038: errno=-28 No space left
We now use btrfs_can_overcommit() to see if we can flip a block group
read only. Before this would fail because we weren't taking into
account the usable un-allocated space for allocating chunks. With my
patches we were allowed to do the balance, which is technically correct.
The test is trying to start balance on degraded mount. So now we're
trying to allocate a chunk and cannot because we want to allocate a
RAID1 chunk, but there's only 1 device that's available for usage. This
results in an ENOSPC.
But we shouldn't even be making it this far, we don't have enough
devices to restripe. The problem is we're using btrfs_num_devices(),
that also includes missing devices. That's not actually what we want, we
need to use rw_devices.
The chunk_mutex is not needed here, rw_devices changes only in device
add, remove or replace, all are excluded by EXCL_OP mechanism.
Fixes: e4d8ec0f65 ("Btrfs: implement online profile changing")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add stacktrace, update changelog, drop chunk_mutex ]
Signed-off-by: David Sterba <dsterba@suse.com>
If scrub returns an error we are not copying back the scrub arguments
structure to user space. This prevents user space to know how much
progress scrub has done if an error happened - this includes -ECANCELED
which is returned when users ask for scrub to stop. A particular use
case, which is used in btrfs-progs, is to resume scrub after it is
canceled, in that case it relies on checking the progress from the scrub
arguments structure and then use that progress in a call to resume
scrub.
So fix this by always copying the scrub arguments structure to user
space, overwriting the value returned to user space with -EFAULT only if
copying the structure failed to let user space know that either that
copying did not happen, and therefore the structure is stale, or it
happened partially and the structure is probably not valid and corrupt
due to the partial copy.
Reported-by: Graham Cobb <g.btrfs@cobb.uk.net>
Link: https://lore.kernel.org/linux-btrfs/d0a97688-78be-08de-ca7d-bcb4c7fb397e@cobb.uk.net/
Fixes: 06fe39ab15 ("Btrfs: do not overwrite scrub error with fault error in scrub ioctl")
CC: stable@vger.kernel.org # 5.1+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Tested-by: Graham Cobb <g.btrfs@cobb.uk.net>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull GPIO fixes from Linus Walleij:
"This reverts the GPIOLIB_IRQCHIP in the ThunderX driver.
ThunderX is a piece of Arm-based server chip. I converted the driver
to hierarchical gpiochip without access to real silicon and failed
miserably since I didn't take MSI's into account.
Kevin Hao helpfully stepped in and fixed it properly, let's revert it
for v5.5 and put the proper conversion into v5.6"
* tag 'gpio-v5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
Revert "gpio: thunderx: Switch to GPIOLIB_IRQCHIP"
Pull block fixes from Jens Axboe:
"Three fixes that should go into this release:
- The 32-bit segment size fix that I mentioned last week (Ming)
- Use uint for the block size (Mikulas)
- A null_blk zone write handling fix (Damien)"
* tag 'block-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
block: fix an integer overflow in logical block size
null_blk: Fix zone write handling
block: fix get_max_segment_size() overflow on 32bit arch
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c4407046 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCIe Root Port driver for CPU Complex PCIe Root Ports are not
loaded on SNR.
The device ID for SNR PCIe3 unit is used by both uncore driver and the
PCIe Root Port driver. If uncore driver is loaded, the PCIe Root Port
driver never be probed.
Remove the PCIe3 unit for SNR for now. The support for PCIe3 unit will
be added later separately.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200116200210.18937-2-kan.liang@linux.intel.com
Vince reports a worrying issue:
| so I was tracking down some odd behavior in the perf_fuzzer which turns
| out to be because perf_even_open() sometimes returns 0 (indicating a file
| descriptor of 0) even though as far as I can tell stdin is still open.
... and further the cause:
| error is triggered if aux_sample_size has non-zero value.
|
| seems to be this line in kernel/events/core.c:
|
| if (perf_need_aux_event(event) && !perf_get_aux_event(event, group_leader))
| goto err_locked;
|
| (note, err is never set)
This seems to be a thinko in commit:
ab43762ef0 ("perf: Allow normal events to output AUX data")
... and we should probably return -EINVAL here, as this should only
happen when the new event is mis-configured or does not have a
compatible aux_event group leader.
Fixes: ab43762ef0 ("perf: Allow normal events to output AUX data")
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
syzbot reported some bogus lockdep warnings, for example bad unlock
balance in sch_direct_xmit(). They are due to a race condition between
slow path and fast path, that is qdisc_xmit_lock_key gets re-registered
in netdev_update_lockdep_key() on slow path, while we could still
acquire the queue->_xmit_lock on fast path in this small window:
CPU A CPU B
__netif_tx_lock();
lockdep_unregister_key(qdisc_xmit_lock_key);
__netif_tx_unlock();
lockdep_register_key(qdisc_xmit_lock_key);
In fact, unlike the addr_list_lock which has to be reordered when
the master/slave device relationship changes, queue->_xmit_lock is
only acquired on fast path and only when NETIF_F_LLTX is not set,
so there is likely no nested locking for it.
Therefore, we can just get rid of re-registration of
qdisc_xmit_lock_key.
Reported-by: syzbot+4ec99438ed7450da6272@syzkaller.appspotmail.com
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net
The following patchset contains Netfilter fixes for net:
1) Fix use-after-free in ipset bitmap destroy path, from Cong Wang.
2) Missing init netns in entry cleanup path of arp_tables,
from Florian Westphal.
3) Fix WARN_ON in set destroy path due to missing cleanup on
transaction error.
4) Incorrect netlink sanity check in tunnel, from Florian Westphal.
5) Missing sanity check for erspan version netlink attribute, also
from Florian.
6) Remove WARN in nft_request_module() that can be triggered from
userspace, from Florian Westphal.
7) Memleak in NFTA_HOOK_DEVS netlink parser, from Dan Carpenter.
8) List poison from commit path for flowtables that are added and
deleted in the same batch, from Florian Westphal.
9) Fix NAT ICMP packet corruption, from Eyal Birger.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 91d2a812df ("locking/rwsem: Make handoff writer
optimistically spin on owner") will allow a recently woken up waiting
writer to spin on the owner. Unfortunately, if the owner happens to be
RWSEM_OWNER_UNKNOWN, the code will incorrectly spin on it leading to a
kernel crash. This is fixed by passing the proper non-spinnable bits
to rwsem_spin_on_owner() so that RWSEM_OWNER_UNKNOWN will be treated
as a non-spinnable target.
Fixes: 91d2a812df ("locking/rwsem: Make handoff writer optimistically spin on owner")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200115154336.8679-1-longman@redhat.com
If the credentials or the mm doesn't match, don't allow the task to
submit anything on behalf of this ring. The task that owns the ring can
pass the file descriptor to another task, but we don't want to allow
that task to submit an SQE that then assumes the ring mm and creds if
it needs to go async.
Cc: stable@vger.kernel.org
Suggested-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
Pull clk fixes from Stephen Boyd:
"Second collection of clk fixes for the next release.
This one includes a fix for PM on TI SoCs with sysc devices and fixes
a bunch of clks that are stuck always enabled on Qualcomm SDM845 SoCs.
Allwinner SoCs get the usual set of fixes too, mostly correcting
drivers to have the right bits that match the hardware.
There's also a Samsung and Tegra fix in here to mark a clk critical
and avoid a double free.
And finally there's a fix for critical clks that silences a big
warning splat about trying to enable a clk that couldn't even be
prepared"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dra7-atl: Remove pm_runtime_irq_safe()
clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: Don't try to enable critical clocks if prepare failed
clk: tegra: Fix double-free in tegra_clk_init()
clk: samsung: exynos5420: Keep top G3D clocks enabled
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
Pull power management fix from Rafael Wysocki:
"Fix a coding mistake in the teo cpuidle governor causing data to be
written beyond the last array element (Ikjoon Jang)"
* tag 'pm-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Fix intervals[] array indexing bug
If the SME and SEV features are present via CPUID, but memory encryption
support is not enabled (MSR 0xC001_0010[23]), the feature flags are cleared
using clear_cpu_cap(). However, if get_cpu_cap() is later called, these
feature flags will be reset back to present, which is not desired.
Change from using clear_cpu_cap() to setup_clear_cpu_cap() so that the
clearing of the flags is maintained.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.16.x-
Link: https://lkml.kernel.org/r/226de90a703c3c0be5a49565047905ac4e94e8f3.1579125915.git.thomas.lendacky@amd.com
Pull chrome platform fix from Benson Leung:
"One fix in the wilco_ec keyboard backlight driver to allow the EC
driver to continue loading in the absence of a backlight module"
* tag 'tag-chrome-platform-fixes-for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: Fix keyboard backlight probing
Commit 8303b7e8f0 ("netfilter: nat: fix spurious connection timeouts")
made nf_nat_icmp_reply_translation() use icmp_manip_pkt() as the l4
manipulation function for the outer packet on ICMP errors.
However, icmp_manip_pkt() assumes the packet has an 'id' field which
is not correct for all types of ICMP messages.
This is not correct for ICMP error packets, and leads to bogus bytes
being written the ICMP header, which can be wrongfully regarded as
'length' bytes by RFC 4884 compliant receivers.
Fix by assigning the 'id' field only for ICMP messages that have this
semantic.
Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Fixes: 8303b7e8f0 ("netfilter: nat: fix spurious connection timeouts")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The only callers of the function lapbeth_get_x25_dev()
are lapbeth_rcv() and lapbeth_device_event().
lapbeth_rcv() uses rcu_read_lock() whereas lapbeth_device_event()
is called with RTNL held (As mentioned in the comments).
Therefore, pass lockdep_rtnl_is_held() as cond argument in
list_for_each_entry_rcu();
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik04@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported following crash:
list_del corruption, ffff88808c9bb000->prev is LIST_POISON2 (dead000000000122)
[..]
Call Trace:
__list_del_entry include/linux/list.h:131 [inline]
list_del_rcu include/linux/rculist.h:148 [inline]
nf_tables_commit+0x1068/0x3b30 net/netfilter/nf_tables_api.c:7183
[..]
The commit transaction list has:
NFT_MSG_NEWTABLE
NFT_MSG_NEWFLOWTABLE
NFT_MSG_DELFLOWTABLE
NFT_MSG_DELTABLE
A missing generation check during DELTABLE processing causes it to queue
the DELFLOWTABLE operation a second time, so we corrupt the list here:
case NFT_MSG_DELFLOWTABLE:
list_del_rcu(&nft_trans_flowtable(trans)->list);
nf_tables_flowtable_notify(&trans->ctx,
because we have two different DELFLOWTABLE transactions for the same
flowtable. We then call list_del_rcu() twice for the same flowtable->list.
The object handling seems to suffer from the same bug so add a generation
check too and only queue delete transactions for flowtables/objects that
are still active in the next generation.
Reported-by: syzbot+37a6804945a3a13b1572@syzkaller.appspotmail.com
Fixes: 3b49e2e94e ("netfilter: nf_tables: add flow table netlink frontend")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This WARN can trigger because some of the names fed to the module
autoload function can be of arbitrary length.
Remove the WARN and add limits for all NLA_STRING attributes.
Reported-by: syzbot+0e63ae76d117ae1c3a01@syzkaller.appspotmail.com
Fixes: 452238e8d5 ("netfilter: nf_tables: add and use helper for module autoload")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f0
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c94 ("net-next: dsa: add Qualcomm tag RX/TX handler")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name is GSWIP (Gigabit Switch IP). Typo was introduced in
875138f81d ("dsa: Move tagger name into its ops structure") while
moving tagger names to their structures.
Fixes: 875138f81d ("dsa: Move tagger name into its ops structure")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b6958 ("macvlan: do not assume mac_header is set in macvlan_broadcast()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jurgen Van Ham <juvanham@gmail.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffered read in fuse normally goes via:
-> generic_file_buffered_read()
-> fuse_readpages()
-> fuse_send_readpages()
->fuse_simple_request() [called since v5.4]
In the case of a read request, fuse_simple_request() will return a
non-negative bytecount on success or a negative error value. A positive
bytecount was taken to be an error and the PG_error flag set on the page.
This resulted in generic_file_buffered_read() falling back to ->readpage(),
which would repeat the read request and succeed. Because of the repeated
read succeeding the bug was not detected with regression tests or other use
cases.
The FTP module in GVFS however fails the second read due to the
non-seekable nature of FTP downloads.
Fix by checking and ignoring positive return value from
fuse_simple_request().
Reported-by: Ondrej Holy <oholy@redhat.com>
Link: https://gitlab.gnome.org/GNOME/gvfs/issues/441
Fixes: 134831e36b ("fuse: convert readpages to simple api")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Daniel Borkmann says:
====================
pull-request: bpf 2020-01-15
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 9 day(s) which contain
a total of 13 files changed, 95 insertions(+), 43 deletions(-).
The main changes are:
1) Fix refcount leak for TCP time wait and request sockets for socket lookup
related BPF helpers, from Lorenz Bauer.
2) Fix wrong verification of ARSH instruction under ALU32, from Daniel Borkmann.
3) Batch of several sockmap and related TLS fixes found while operating
more complex BPF programs with Cilium and OpenSSL, from John Fastabend.
4) Fix sockmap to read psock's ingress_msg queue before regular sk_receive_queue()
to avoid purging data upon teardown, from Lingpeng Chen.
5) Fix printing incorrect pointer in bpftool's btf_dump_ptr() in order to properly
dump a BPF map's value with BTF, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit moved the locking for the async sqthread, but didn't
take into account that the io-wq workers still need it. We can't use
req->in_async for this anymore as both the sqthread and io-wq workers
set it, gate the need for locking on io_wq_current_is_worker() instead.
Fixes: 8a4955ff1c ("io_uring: sqthread should grab ctx->uring_lock for submissions")
Reported-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.
For exmaple (run this on an architecture with 64k pages):
Mount will fail with this error because it tries to read the superblock using 2-sector
access:
device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
EXT4-fs (dm-0): unable to read superblock
This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
req->result is cleared when io_issue_sqe() calls io_read/write_pre()
routines. Those routines however are not called when the sqe
argument is NULL, which is the case when io_issue_sqe() is called from
io_wq_submit_work(). io_issue_sqe() may then examine a stale result if
a polled request had previously failed with -EAGAIN:
if (ctx->flags & IORING_SETUP_IOPOLL) {
if (req->result == -EAGAIN)
return -EAGAIN;
io_iopoll_req_issued(req);
}
and in turn cause a subsequently completed request to be re-issued in
io_wq_submit_work().
Signed-off-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tom Hatskevich reported that we look up "iocp" then, in the called
functions we do a second copy_from_user() and look it up again.
The problem that could cause is:
drivers/message/fusion/mptctl.c
674 /* All of these commands require an interrupt or
675 * are unknown/illegal.
676 */
677 if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0)
^^^^
We take this lock.
678 return ret;
679
680 if (cmd == MPTFWDOWNLOAD)
681 ret = mptctl_fw_download(arg);
^^^
Then the user memory changes and we look up "iocp" again but a different
one so now we are holding the incorrect lock and have a race condition.
682 else if (cmd == MPTCOMMAND)
683 ret = mptctl_mpt_command(arg);
The security impact of this bug is not as bad as it could have been
because these operations are all privileged and root already has
enormous destructive power. But it's still worth fixing.
This patch passes the "iocp" pointer to the functions to avoid the
second lookup. That deletes 100 lines of code from the driver so
it's a nice clean up as well.
Link: https://lore.kernel.org/r/20200114123414.GA7957@kadam
Reported-by: Tom Hatskevich <tom2001tom.23@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 0ed8810276 ("scsi: storvsc: setup 1:1 mapping between hardware
queue and CPU queue") introduced a regression for disks attached to
IDE. For these disks the host VSP only offers one VMBUS channel. Setting
multiple queues can overload the VMBUS channel and result in performance
drop for high queue depth workload on system with large number of CPUs.
Fix it by leaving the number of hardware queues to 1 (default value) for
IDE disks.
Fixes: 0ed8810276 ("scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue")
Link: https://lore.kernel.org/r/1578960516-108228-1-git-send-email-longli@linuxonhyperv.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA")
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code in secondary_park is currently placed in the .init section. The
kernel reclaims and clears this code when it finishes booting. That
causes the cores parked in it to go to somewhere unpredictable, so we
move this function out of init to make sure the cores stay looping there.
The instruction bgeu a0, t0, .Lsecondary_park may have "a relocation
truncated to fit" issue during linking time. It is because that sections
are too far to jump. Let's use tail to jump to the .Lsecondary_park.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup.patel@sifive.com>
Cc: Andreas Schwab <schwab@suse.de>
Cc: stable@vger.kernel.org
Fixes: 76d2a0493a ("RISC-V: Init and Halt Code")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
John Fastabend says:
====================
To date our usage of sockmap/tls has been fairly simple, the BPF programs
did only well-defined pop, push, pull and apply/cork operations.
Now that we started to push more complex programs into sockmap we uncovered
a series of issues addressed here. Further OpenSSL3.0 version should be
released soon with kTLS support so its important to get any remaining
issues on BPF and kTLS support resolved.
Additionally, I have a patch under development to allow sockmap to be
enabled/disabled at runtime for Cilium endpoints. This allows us to stress
the map insert/delete with kTLS more than previously where Cilium only
added the socket to the map when it entered ESTABLISHED state and never
touched it from the control path side again relying on the sockets own
close() hook to remove it.
To test I have a set of test cases in test_sockmap.c that expose these
issues. Once we get fixes here merged and in bpf-next I'll submit the
tests to bpf-next tree to ensure we don't regress again. Also I've run
these patches in the Cilium CI with OpenSSL (master branch) this will
run tools such as netperf, ab, wrk2, curl, etc. to get a broad set of
testing.
I'm aware of two more issues that we are working to resolve in another
couple (probably two) patches. First we see an auth tag corruption in
kTLS when sending small 1byte chunks under stress. I've not pinned this
down yet. But, guessing because its under 1B stress tests it must be
some error path being triggered. And second we need to ensure BPF RX
programs are not skipped when kTLS ULP is loaded. This breaks some of the
sockmap selftests when running with kTLS. I'll send a follow up for this.
v2: I dropped a patch that added !0 size check in tls_push_record
this originated from a panic I caught awhile ago with a trace
in the crypto stack. But I can not reproduce it anymore so will
dig into that and send another patch later if needed. Anyways
after a bit of thought it would be nicer if tls/crypto/bpf didn't
require special case handling for the !0 size.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When user returns SK_DROP we need to reset the number of copied bytes
to indicate to the user the bytes were dropped and not sent. If we
don't reset the copied arg sendmsg will return as if those bytes were
copied giving the user a positive return value.
This works as expected today except in the case where the user also
pops bytes. In the pop case the sg.size is reduced but we don't correctly
account for this when copied bytes is reset. The popped bytes are not
accounted for and we return a small positive value potentially confusing
the user.
The reason this happens is due to a typo where we do the wrong comparison
when accounting for pop bytes. In this fix notice the if/else is not
needed and that we have a similar problem if we push data except its not
visible to the user because if delta is larger the sg.size we return a
negative value so it appears as an error regardless.
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-9-john.fastabend@gmail.com
Its possible through a set of push, pop, apply helper calls to construct
a skmsg, which is just a ring of scatterlist elements, with the start
value larger than the end value. For example,
end start
|_0_|_1_| ... |_n_|_n+1_|
Where end points at 1 and start points and n so that valid elements is
the set {n, n+1, 0, 1}.
Currently, because we don't build the correct chain only {n, n+1} will
be sent. This adds a check and sg_chain call to correctly submit the
above to the crypto and tls send path.
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-8-john.fastabend@gmail.com
It is possible to build a plaintext buffer using push helper that is larger
than the allocated encrypt buffer. When this record is pushed to crypto
layers this can result in a NULL pointer dereference because the crypto
API expects the encrypt buffer is large enough to fit the plaintext
buffer. Kernel splat below.
To resolve catch the cases this can happen and split the buffer into two
records to send individually. Unfortunately, there is still one case to
handle where the split creates a zero sized buffer. In this case we merge
the buffers and unmark the split. This happens when apply is zero and user
pushed data beyond encrypt buffer. This fixes the original case as well
because the split allocated an encrypt buffer larger than the plaintext
buffer and the merge simply moves the pointers around so we now have
a reference to the new (larger) encrypt buffer.
Perhaps its not ideal but it seems the best solution for a fixes branch
and avoids handling these two cases, (a) apply that needs split and (b)
non apply case. The are edge cases anyways so optimizing them seems not
necessary unless someone wants later in next branches.
[ 306.719107] BUG: kernel NULL pointer dereference, address: 0000000000000008
[...]
[ 306.747260] RIP: 0010:scatterwalk_copychunks+0x12f/0x1b0
[...]
[ 306.770350] Call Trace:
[ 306.770956] scatterwalk_map_and_copy+0x6c/0x80
[ 306.772026] gcm_enc_copy_hash+0x4b/0x50
[ 306.772925] gcm_hash_crypt_remain_continue+0xef/0x110
[ 306.774138] gcm_hash_crypt_continue+0xa1/0xb0
[ 306.775103] ? gcm_hash_crypt_continue+0xa1/0xb0
[ 306.776103] gcm_hash_assoc_remain_continue+0x94/0xa0
[ 306.777170] gcm_hash_assoc_continue+0x9d/0xb0
[ 306.778239] gcm_hash_init_continue+0x8f/0xa0
[ 306.779121] gcm_hash+0x73/0x80
[ 306.779762] gcm_encrypt_continue+0x6d/0x80
[ 306.780582] crypto_gcm_encrypt+0xcb/0xe0
[ 306.781474] crypto_aead_encrypt+0x1f/0x30
[ 306.782353] tls_push_record+0x3b9/0xb20 [tls]
[ 306.783314] ? sk_psock_msg_verdict+0x199/0x300
[ 306.784287] bpf_exec_tx_verdict+0x3f2/0x680 [tls]
[ 306.785357] tls_sw_sendmsg+0x4a3/0x6a0 [tls]
test_sockmap test signature to trigger bug,
[TEST]: (1, 1, 1, sendmsg, pass,redir,start 1,end 2,pop (1,2),ktls,):
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-7-john.fastabend@gmail.com
Leaving an incorrect end mark in place when passing to crypto
layer will cause crypto layer to stop processing data before
all data is encrypted. To fix clear the end mark on push
data instead of expecting users of the helper to clear the
mark value after the fact.
This happens when we push data into the middle of a skmsg and
have room for it so we don't do a set of copies that already
clear the end flag.
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-6-john.fastabend@gmail.com
In the push, pull, and pop helpers operating on skmsg objects to make
data writable or insert/remove data we use this bounds check to ensure
specified data is valid,
/* Bounds checks: start and pop must be inside message */
if (start >= offset + l || last >= msg->sg.size)
return -EINVAL;
The problem here is offset has already included the length of the
current element the 'l' above. So start could be past the end of
the scatterlist element in the case where start also points into an
offset on the last skmsg element.
To fix do the accounting slightly different by adding the length of
the previous entry to offset at the start of the iteration. And
ensure its initialized to zero so that the first iteration does
nothing.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Fixes: 6fff607e2f ("bpf: sk_msg program helper bpf_msg_push_data")
Fixes: 7246d8ed4d ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-5-john.fastabend@gmail.com
When sockmap sock with TLS enabled is removed we cleanup bpf/psock state
and call tcp_update_ulp() to push updates to TLS ULP on top. However, we
don't push the write_space callback up and instead simply overwrite the
op with the psock stored previous op. This may or may not be correct so
to ensure we don't overwrite the TLS write space hook pass this field to
the ULP and have it fixup the ctx.
This completes a previous fix that pushed the ops through to the ULP
but at the time missed doing this for write_space, presumably because
write_space TLS hook was added around the same time.
Fixes: 95fa145479 ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-4-john.fastabend@gmail.com
The sock_map_free() and sock_hash_free() paths used to delete sockmap
and sockhash maps walk the maps and destroy psock and bpf state associated
with the socks in the map. When done the socks no longer have BPF programs
attached and will function normally. This can happen while the socks in
the map are still "live" meaning data may be sent/received during the walk.
Currently, though we don't take the sock_lock when the psock and bpf state
is removed through this path. Specifically, this means we can be writing
into the ops structure pointers such as sendmsg, sendpage, recvmsg, etc.
while they are also being called from the networking side. This is not
safe, we never used proper READ_ONCE/WRITE_ONCE semantics here if we
believed it was safe. Further its not clear to me its even a good idea
to try and do this on "live" sockets while networking side might also
be using the socket. Instead of trying to reason about using the socks
from both sides lets realize that every use case I'm aware of rarely
deletes maps, in fact kubernetes/Cilium case builds map at init and
never tears it down except on errors. So lets do the simple fix and
grab sock lock.
This patch wraps sock deletes from maps in sock lock and adds some
annotations so we catch any other cases easier.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-3-john.fastabend@gmail.com
When a sockmap is free'd and a socket in the map is enabled with tls
we tear down the bpf context on the socket, the psock struct and state,
and then call tcp_update_ulp(). The tcp_update_ulp() call is to inform
the tls stack it needs to update its saved sock ops so that when the tls
socket is later destroyed it doesn't try to call the now destroyed psock
hooks.
This is about keeping stacked ULPs in good shape so they always have
the right set of stacked ops.
However, recently unhash() hook was removed from TLS side. But, the
sockmap/bpf side is not doing any extra work to update the unhash op
when is torn down instead expecting TLS side to manage it. So both
TLS and sockmap believe the other side is managing the op and instead
no one updates the hook so it continues to point at tcp_bpf_unhash().
When unhash hook is called we call tcp_bpf_unhash() which detects the
psock has already been destroyed and calls sk->sk_prot_unhash() which
calls tcp_bpf_unhash() yet again and so on looping and hanging the core.
To fix have sockmap tear down logic fixup the stale pointer.
Fixes: 5d92e631b8 ("net/tls: partially revert fix transition through disconnect with close")
Reported-by: syzbot+83979935eb6304f8cd46@syzkaller.appspotmail.com
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20200111061206.8028-2-john.fastabend@gmail.com
Jose Abreu says:
====================
net: stmmac: Fix selftests in Synopsys AXS101 board
Set of fixes for sefltests so that they work in Synopsys AXS101 board.
Final output:
$ ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control -95
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame 0
30. Multichannel Jumbo -95
31. Split Header -95
Description:
1) Fixes the unaligned accesses that caused CPU halt in Synopsys AXS101
boards.
2) Fixes the VLAN tests when filtering failed to work.
3) Fixes the VLAN Perfect tests when filtering is not available in HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When HW does not support perfect filtering the feature will not be
enabled in the net_device. Add a check for this to prevent failures.
Fixes: 1b2250a04c ("net: stmmac: selftests: Add tests for VLAN Perfect Filtering")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e1838200 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array utdm_info is declared as an array of MAX_HDLC_NUM (4) elements
however up to UCC_MAX_NUM (8) elements are potentially being written
to it. Currently we have an array out-of-bounds write error on the
last 4 elements. Fix this by making utdm_info UCC_MAX_NUM elements in
size.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: c19b6d246a ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Why]
Noticed this while testing MST with the 4 ports MST hub from
StarTech.com. Sometimes can't light up monitors normally and get the
error message as 'sideband msg build failed'.
Look into aux transactions, found out that source sometimes will send
out another down request before receiving the down reply of the
previous down request. On the other hand, in drm_dp_get_one_sb_msg(),
current code doesn't handle the interleaved replies case. Hence, source
can't build up message completely and can't light up monitors.
[How]
For good compatibility, enforce source to send out one down request at a
time. Add a flag, is_waiting_for_dwn_reply, to determine if the source
can send out a down request immediately or not.
- Check the flag before calling process_single_down_tx_qlock to send out
a msg
- Set the flag when successfully send out a down request
- Clear the flag when successfully build up a down reply
- Clear the flag when find erros during sending out a down request
- Clear the flag when find errors during building up a down reply
- Clear the flag when timeout occurs during waiting for a down reply
- Use drm_dp_mst_kick_tx() to try to send another down request in queue
at the end of drm_dp_mst_wait_tx_reply() (attempt to send out messages
in queue when errors occur)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113093649.11755-1-Wayne.Lin@amd.com
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- Fix DAT candidate selection on little endian systems,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (85) call bpf_get_socket_cookie#46
1: R0_w=invP(id=0) R10=fp0
1: (57) r0 &= 808464432
2: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
2: (14) w0 -= 810299440
3: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
3: (c4) w0 s>>= 1
4: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
4: (76) if w0 s>= 0x30303030 goto pc+216
221: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
221: (95) exit
processed 6 insns (limit 1000000) [...]
Taking a closer look, the program was xlated as follows:
# ./bpftool p d x i 12
0: (85) call bpf_get_socket_cookie#7800896
1: (bf) r6 = r0
2: (57) r6 &= 808464432
3: (14) w6 -= 810299440
4: (c4) w6 s>>= 1
5: (76) if w6 s>= 0x30303030 goto pc+216
6: (05) goto pc-1
7: (05) goto pc-1
8: (05) goto pc-1
[...]
220: (05) goto pc-1
221: (05) goto pc-1
222: (95) exit
Meaning, the visible effect is very similar to f54c7898ed ("bpf: Fix
precision tracking for unbounded scalars"), that is, the fall-through
branch in the instruction 5 is considered to be never taken given the
conclusion from the min/max bounds tracking in w6, and therefore the
dead-code sanitation rewrites it as goto pc-1. However, real-life input
disagrees with verification analysis since a soft-lockup was observed.
The bug sits in the analysis of the ARSH. The definition is that we shift
the target register value right by K bits through shifting in copies of
its sign bit. In adjust_scalar_min_max_vals(), we do first coerce the
register into 32 bit mode, same happens after simulating the operation.
However, for the case of simulating the actual ARSH, we don't take the
mode into account and act as if it's always 64 bit, but location of sign
bit is different:
dst_reg->smin_value >>= umin_val;
dst_reg->smax_value >>= umin_val;
dst_reg->var_off = tnum_arshift(dst_reg->var_off, umin_val);
Consider an unknown R0 where bpf_get_socket_cookie() (or others) would
for example return 0xffff. With the above ARSH simulation, we'd see the
following results:
[...]
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP65535 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (57) r0 &= 808464432
-> R0_runtime = 0x3030
3: R0_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
3: (14) w0 -= 810299440
-> R0_runtime = 0xcfb40000
4: R0_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
(0xffffffff)
4: (c4) w0 s>>= 1
-> R0_runtime = 0xe7da0000
5: R0_w=invP(id=0,umin_value=1740636160,umax_value=2147221496,var_off=(0x67c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0x7ffbfff8)
[...]
In insn 3, we have a runtime value of 0xcfb40000, which is '1100 1111 1011
0100 0000 0000 0000 0000', the result after the shift has 0xe7da0000 that
is '1110 0111 1101 1010 0000 0000 0000 0000', where the sign bit is correctly
retained in 32 bit mode. In insn4, the umax was 0xffffffff, and changed into
0x7ffbfff8 after the shift, that is, '0111 1111 1111 1011 1111 1111 1111 1000'
and means here that the simulation didn't retain the sign bit. With above
logic, the updates happen on the 64 bit min/max bounds and given we coerced
the register, the sign bits of the bounds are cleared as well, meaning, we
need to force the simulation into s32 space for 32 bit alu mode.
Verification after the fix below. We're first analyzing the fall-through branch
on 32 bit signed >= test eventually leading to rejection of the program in this
specific case:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r2 = 808464432
1: R1=ctx(id=0,off=0,imm=0) R2_w=invP808464432 R10=fp0
1: (85) call bpf_get_socket_cookie#46
2: R0_w=invP(id=0) R10=fp0
2: (bf) r6 = r0
3: R0_w=invP(id=0) R6_w=invP(id=0) R10=fp0
3: (57) r6 &= 808464432
4: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=808464432,var_off=(0x0; 0x30303030)) R10=fp0
4: (14) w6 -= 810299440
5: R0_w=invP(id=0) R6_w=invP(id=0,umax_value=4294967295,var_off=(0xcf800000; 0x3077fff0)) R10=fp0
5: (c4) w6 s>>= 1
6: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
(0x67c00000) (0xfffbfff8)
6: (76) if w6 s>= 0x30303030 goto pc+216
7: R0_w=invP(id=0) R6_w=invP(id=0,umin_value=3888119808,umax_value=4294705144,var_off=(0xe7c00000; 0x183bfff8)) R10=fp0
7: (30) r0 = *(u8 *)skb[808464432]
BPF_LD_[ABS|IND] uses reserved fields
processed 8 insns (limit 1000000) [...]
Fixes: 9cbe1f5a32 ("bpf/verifier: improve register value range tracking with ARSH")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115204733.16648-1-daniel@iogearbox.net
kmemleak detects the following memory leak when hot removing
a network device:
unreferenced object 0xffff888083f63600 (size 256):
comm "kworker/0:1", pid 12, jiffies 4294831717 (age 1113.676s)
hex dump (first 32 bytes):
00 40 c7 33 80 88 ff ff 00 00 00 00 10 00 00 00 .@.3............
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
backtrace:
[<00000000d4a8f5be>] rndis_filter_device_add+0x117/0x11c0 [hv_netvsc]
[<000000009c02d75b>] netvsc_probe+0x5e7/0xbf0 [hv_netvsc]
[<00000000ddafce23>] vmbus_probe+0x74/0x170 [hv_vmbus]
[<00000000046e64f1>] really_probe+0x22f/0xb50
[<000000005cc35eb7>] driver_probe_device+0x25e/0x370
[<0000000043c642b2>] bus_for_each_drv+0x11f/0x1b0
[<000000005e3d09f0>] __device_attach+0x1c6/0x2f0
[<00000000a72c362f>] bus_probe_device+0x1a6/0x260
[<0000000008478399>] device_add+0x10a3/0x18e0
[<00000000cf07b48c>] vmbus_device_register+0xe7/0x1e0 [hv_vmbus]
[<00000000d46cf032>] vmbus_add_channel_work+0x8ab/0x1770 [hv_vmbus]
[<000000002c94bb64>] process_one_work+0x919/0x17d0
[<0000000096de6781>] worker_thread+0x87/0xb40
[<00000000fbe7397e>] kthread+0x333/0x3f0
[<000000004f844269>] ret_from_fork+0x3a/0x50
rndis_filter_device_add() allocates an instance of struct rndis_device
which never gets deallocated as rndis_filter_device_remove() sets
net_device->extension which points to the rndis_device struct to NULL,
leaving the rndis_device dangling.
Since net_device->extension is eventually freed in free_netvsc_device(),
we refrain from setting it to NULL inside rndis_filter_device_remove()
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet pointed to by retransmit_skb_hint is unlinked by ACK,
retransmit_skb_hint will be set to NULL in tcp_clean_rtx_queue().
If packet loss is detected at this time, retransmit_skb_hint will be set
to point to the current packet loss in tcp_verify_retransmit_hint(),
then the packets that were previously marked lost but not retransmitted
due to the restriction of cwnd will be skipped and cannot be
retransmitted.
To fix this, when retransmit_skb_hint is NULL, retransmit_skb_hint can
be reset only after all marked lost packets are retransmitted
(retrans_out >= lost_out), otherwise we need to traverse from
tcp_rtx_queue_head in tcp_xmit_retransmit_queue().
Packetdrill to demonstrate:
// Disable RACK and set max_reordering to keep things simple
0 `sysctl -q net.ipv4.tcp_recovery=0`
+0 `sysctl -q net.ipv4.tcp_max_reordering=3`
// Establish a connection
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+.1 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <...>
+.01 < . 1:1(0) ack 1 win 257
+0 accept(3, ..., ...) = 4
// Send 8 data segments
+0 write(4, ..., 8000) = 8000
+0 > P. 1:8001(8000) ack 1
// Enter recovery and 1:3001 is marked lost
+.01 < . 1:1(0) ack 1 win 257 <sack 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:6001 3001:4001,nop,nop>
+0 < . 1:1(0) ack 1 win 257 <sack 5001:7001 3001:4001,nop,nop>
// Retransmit 1:1001, now retransmit_skb_hint points to 1001:2001
+0 > . 1:1001(1000) ack 1
// 1001:2001 was ACKed causing retransmit_skb_hint to be set to NULL
+.01 < . 1:1(0) ack 2001 win 257 <sack 5001:8001 3001:4001,nop,nop>
// Now retransmit_skb_hint points to 4001:5001 which is now marked lost
// BUG: 2001:3001 was not retransmitted
+0 > . 2001:3001(1000) ack 1
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel Software Developer's Manual, volume 3, chapter 9.11.6 says:
"Note that the microcode update must be aligned on a 16-byte boundary
and the size of the microcode update must be 1-KByte granular"
When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image. Image that was created something like this:
iucode_tool --write-earlyfw=FOO.cpio microcode-files...
However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.
Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.
[ If we end up having other firmware with much bigger alignment
requirements, we might need to introduce some method for the firmware
to specify it, this is the minimal "just increase the alignment a bit
to account for this one special case" patch - Linus ]
Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When handling devm_gpiod_get_optional() errors, free the memory already
allocated. This fixes Smatch warnings:
drivers/i2c/busses/i2c-iop3xx.c:437 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
drivers/i2c/busses/i2c-iop3xx.c:442 iop3xx_i2c_probe() warn: possible memory leak of 'new_adapter'
Fixes: fdb7e884ad ("i2c: iop: Use GPIO descriptors")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull x86 platform driver fixes from Andy Shevchenko:
- Fix keyboard brightness control for ASUS laptops
- Better handling parameters of GPD pocket fan module to avoid
thermal shock
- Add IDs to PMC platform driver to support Intel Comet Lake
- Fix potential dead lock in Mellanox TM FIFO driver and ABI
documentation
* tag 'platform-drivers-x86-v5.5-3' of git://git.infradead.org/linux-platform-drivers-x86:
Documentation/ABI: Add missed attribute for mlxreg-io sysfs interfaces
Documentation/ABI: Fix documentation inconsistency for mlxreg-io sysfs interfaces
platform/x86: asus-wmi: Fix keyboard brightness cannot be set to 0
platform/x86: intel_pmc_core: update Comet Lake platform driver
platform/x86: GPD pocket fan: Allow somewhat lower/higher temperature limits
platform/x86: GPD pocket fan: Use default values when wrong modparams are given
platform/mellanox: fix potential deadlock in the tmfifo driver
platform/x86: intel-ips: Use the correct style for SPDX License Identifier
Pull crypto fix from Herbert Xu:
"This fixes a build problem for the hisilicon driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hisilicon/sec2 - Use atomics instead of __sync
Pull vfs fixes from Al Viro:
"Fixes for mountpoint_last() bugs (by converting to use of
lookup_last()) and an autofs regression fix from this cycle (caused by
follow_managed() breakage introduced in barrier fixes series)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix autofs regression caused by follow_managed() changes
reimplement path_mountpoint() with less magic
One of the recent Tegra I2C commits made a change that resumes runtime PM
during driver's probe, but it missed to put the RPM in a case of error.
Note that it's not correct to use pm_runtime_status_suspended because it
breaks RPM refcounting.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I noticed that sometime I2C clock is kept enabled during suspend-resume.
This happens because runtime PM defers dynamic suspension and thus it may
happen that runtime PM is in active state when system enters into suspend.
In particular I2C controller that is used for CPU's DVFS is often kept ON
during suspend because CPU's voltage scaling happens quite often.
Fixes: 8ebf15e9c8 ("i2c: tegra: Move suspend handling to NOIRQ phase")
Cc: <stable@vger.kernel.org> # v5.4+
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
null_zone_write() only allows writing empty and implicitly opened zones.
Writing to closed and explicitly opened zones must also be allowed and
the zone condition must be transitioned to implicit open if the zone
is not explicitly opened already.
Fixes: da644b2cc1 ("null_blk: add zone open, close, and finish support")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes a regression on setting up asynchronous commands to use
external trigger sources when board-specific routing information is
missing.
`ni_find_device_routes()` (called via `ni_assign_device_routes()`) finds
the table of register values for the device family and the set of valid
routes for the specific board. If both are found,
`tables->route_values` is set to point to the table of register values
for the device family and `tables->valid_routes` is set to point to the
list of valid routes for the specific board. If either is not found,
both `tables->route_values` and `tables->valid_routes` are left set at
their initial null values (initialized by `ni_assign_device_routes()`)
and the function returns `-ENODATA`.
Returning an error results in some routing functionality being disabled.
Unfortunately, leaving `table->route_values` set to `NULL` also breaks
the setting up of asynchronous commands that are configured to use
external trigger sources. Calls to `ni_check_trigger_arg()` or
`ni_check_trigger_arg_roffs()` while checking the asynchronous command
set-up would result in a null pointer dereference if
`table->route_values` is `NULL`. The null pointer dereference is fixed
in another patch, but it now results in failure to set up the
asynchronous command. That is a regression from the behavior prior to
commit 347e244884 ("staging: comedi: tio: implement global tio/ctr
routing") and commit 56d0b826d3 ("staging: comedi: ni_mio_common:
implement new routing for TRIG_EXT").
Change `ni_find_device_routes()` to set `tables->route_values` and/or
`tables->valid_routes` to valid information even if the other one can
only be set to `NULL` due to missing information. The function will
still return an error in that case. This should result in
`tables->valid_routes` being valid for all currently supported device
families even if the board-specific routing information is missing.
That should be enough to fix the regression on setting up asynchronous
commands to use external triggers for boards with missing routing
information.
Fixes: 347e244884 ("staging: comedi: tio: implement global tio/ctr routing")
Fixes: 56d0b826d3 ("staging: comedi: ni_mio_common: implement new routing for TRIG_EXT").
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In `ni_find_route_source()`, `tables->route_values` gets dereferenced.
However it is possible that `tables->route_values` is `NULL`, leading to
a null pointer dereference. `tables->route_values` will be `NULL` if
the call to `ni_assign_device_routes()` during board initialization
returned an error due to missing device family routing information or
missing board-specific routing information. For example, there is
currently no board-specific routing information provided for the
PCIe-6251 board and several other boards, so those are affected by this
bug.
The bug is triggered when `ni_find_route_source()` is called via
`ni_check_trigger_arg()` or `ni_check_trigger_arg_roffs()` when checking
the arguments for setting up asynchronous commands. Fix it by returning
`-EINVAL` if `tables->route_values` is `NULL`.
Even with this fix, setting up asynchronous commands to use external
trigger sources for boards with missing routing information will still
fail gracefully. Since `ni_find_route_source()` only depends on the
device family routing information, it would be better if that was made
available even if the board-specific routing information is missing.
That will be addressed by another patch.
Fixes: 4bb90c87ab ("staging: comedi: add interface to ni routing table information")
Cc: <stable@vger.kernel.org> # 4.20+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200114182532.132058-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ido Schimmel says:
====================
mlxsw: Various fixes
This patch set contains various fixes for mlxsw.
Patch #1 splits the init() callback between Spectrum-2 and Spectrum-3 in
order to avoid enforcing the same firmware version for both ASICs, as
this can't possibly work. Without this patch the driver cannot boot with
the Spectrum-3 ASIC.
Patches #2-#3 fix a long standing race condition that was recently
exposed while testing the driver on an emulator, which is very slow
compared to the actual hardware. The problem is explained in detail in
the commit messages.
Patch #4 fixes a selftest.
Patch #5 prevents offloaded qdiscs from presenting a non-zero backlog to
the user when the netdev is down. This is done by clearing the cached
backlog in the driver when the netdev goes down.
Patch #6 fixes qdisc statistics (backlog and tail drops) to also take
into account the multicast traffic classes.
v2:
* Patches #2-#3: use skb_cow_head() instead of skb_unshare() as
suggested by Jakub. Remove unnecessary check regarding headroom
* Patches #5-#6: new
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.
Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.
Fixes: 573363a68f ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a72afb6879 ("mlxsw: Enforce firmware version for
Spectrum-2") I added a required firmware version for Spectrum-2, but
missed the fact that mlxsw_sp2_init() is used by both Spectrum-2 and
Spectrum-3. This means that the same firmware version will be used for
both, which is wrong.
Fix this by creating a new init() callback for Spectrum-3.
Fixes: a72afb6879 ("mlxsw: Enforce firmware version for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hub_activate() is called before D+ has stabilized after remote
wakeup, the following situation might occur:
__ ___________________
/ \ /
D+ __/ \__/
Hub _______________________________
| ^ ^ ^
| | | |
Host _____v__|___|___________|______
| | | |
| | | \-- Interrupt Transfer (*3)
| | \-- ClearPortFeature (*2)
| \-- GetPortStatus (*1)
\-- Host detects remote wakeup
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg says:
====================
A few fixes:
* -O3 enablement fallout, thanks to Arnd who ran this
* fixes for a few leaks, thanks to Felix
* channel 12 regulatory fix for custom regdomains
* check for a crash reported by syzbot
(NULL function is called on drivers that don't have it)
* fix TKIP replay protection after setup with some APs
(from Jouni)
* restrict obtaining some mesh data to avoid WARN_ONs
* fix deadlocks with auto-disconnect (socket owner)
* fix radar detection events with multiple devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is relatively easy to trigger the following boot splat on an Ice Lake
client platform. The call stack is like:
kernel BUG at kernel/timer/timer.c:1152!
Call Trace:
__queue_delayed_work
queue_delayed_work_on
therm_throt_process
intel_thermal_interrupt
...
The reason is that a CPU's thermal interrupt is enabled prior to
executing its hotplug onlining callback which will initialize the
throttling workqueues.
Such a race can lead to therm_throt_process() accessing an uninitialized
therm_work, leading to the above BUG at a very early bootup stage.
Therefore, unmask the thermal interrupt vector only after having setup
the workqueues completely.
[ bp: Heavily massage commit message and correct comment formatting. ]
Fixes: f6656208f0 ("x86/mce/therm_throt: Optimize notifications of thermal throttle")
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20200107004116.59353-1-chuansheng.liu@intel.com
This reverts commit a7fc89f9d5 because
there are some bugs in this commit, and we don't have a simple way to
fix these bugs. So revert this commit to make the thunderx gpio work
on the stable kernel at least. We will switch to GPIOLIB_IRQCHIP
for thunderx gpio by following patches.
Fixes: a7fc89f9d5 ("gpio: thunderx: Switch to GPIOLIB_IRQCHIP")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20200114082821.14015-2-haokexin@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f8 ("cfg80211: reuse existing page fragments in A-MSDU rx")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:
In function 'iw_handler_get_iwstats',
inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
memcpy(extra, stats, sizeof(struct iw_statistics));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here
The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.
Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TKIP replay protection was skipped for the very first frame received
after a new key is configured. While this is potentially needed to avoid
dropping a frame in some cases, this does leave a window for replay
attacks with group-addressed frames at the station side. Any earlier
frame sent by the AP using the same key would be accepted as a valid
frame and the internal RSC would then be updated to the TSC from that
frame. This would allow multiple previously transmitted group-addressed
frames to be replayed until the next valid new group-addressed frame
from the AP is received by the station.
Fix this by limiting the no-replay-protection exception to apply only
for the case where TSC=0, i.e., when this is for the very first frame
protected using the new key, and the local RSC had not been set to a
higher value when configuring the key (which may happen with GTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20200107153545.10934-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
we need to reload ->d_flags after the call of ->d_manage() - the thing
might've been called with dentry still negative and have the damn thing
turned positive while we'd waited.
Fixes: d41efb522e "fs/namei.c: pull positivity check into follow_managed()"
Reported-by: Ian Kent <raven@themaw.net>
Tested-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and get rid of a bunch of bugs in it. Background:
the reason for path_mountpoint() is that umount() really doesn't
want attempts to revalidate the root of what it's trying to umount.
The thing we want to avoid actually happen from complete_walk();
solution was to do something parallel to normal path_lookupat()
and it both went overboard and got the boilerplate subtly
(and not so subtly) wrong.
A better solution is to do pretty much what the normal path_lookupat()
does, but instead of complete_walk() do unlazy_walk(). All it takes
to avoid that ->d_weak_revalidate() call... mountpoint_last() goes
away, along with everything it got wrong, and so does the magic around
LOOKUP_NO_REVAL.
Another source of bugs is that when we traverse mounts at the final
location (and we need to do that - umount . expects to get whatever's
overmounting ., if any, out of the lookup) we really ought to take
care of ->d_manage() - as it is, manual umount of autofs automount
in progress can lead to unpleasant surprises for the daemon. Easily
solved by using handle_lookup_down() instead of follow_mount().
Tested-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If we pass back dependent work in case of links, we need to always
ensure that we call the link setup and work prep handler. If not, we
might be missing some setup for the next work item.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Page pool API will start syncing (if requested) starting from
page->dma_addr + pool->p.offset. Fix dma sync length in
mvneta_run_xdp since we do not need to account xdp headroom
Fixes: 07e13edbb6 ("net: mvneta: get rid of huge dma sync in mvneta_rx_refill")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull NFS client bugfixes from Anna Schumaker:
"Three NFS over RDMA fixes for bugs Chuck found that can be hit during
device removal:
- Fix create_qp crash on device unload
- Fix completion wait during device removal
- Fix oops in receive handler after device removal"
* tag 'nfs-for-5.5-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
xprtrdma: Fix oops in Receive handler after device removal
xprtrdma: Fix completion wait during device removal
xprtrdma: Fix create_qp crash on device unload
Commit 429120f3df starts to take account of segment's start dma address
when computing max segment size, and data type of 'unsigned long'
is used to do that. However, the segment mask may be 0xffffffff, so
the figured out segment size may be overflowed in case of zero physical
address on 32bit arch.
Fix the issue by returning queue_max_segment_size() directly when that
happens.
Fixes: 429120f3df ("block: fix splitting segments on boundary masks")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Christoph Hellwig <hch@lst.de>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, hv_sock restricts the port the guest socket can accept
connections on. hv_sock divides the socket port namespace into two parts
for server side (listening socket), 0-0x7FFFFFFF & 0x80000000-0xFFFFFFFF
(there are no restrictions on client port namespace). The first part
(0-0x7FFFFFFF) is reserved for sockets where connections can be accepted.
The second part (0x80000000-0xFFFFFFFF) is reserved for allocating ports
for the peer (host) socket, once a connection is accepted.
This reservation of the port namespace is specific to hv_sock and not
known by the generic vsock library (ex: af_vsock). This is problematic
because auto-binds/ephemeral ports are handled by the generic vsock
library and it has no knowledge of this port reservation and could
allocate a port that is not compatible with hv_sock (and legitimately so).
The issue hasn't surfaced so far because the auto-bind code of vsock
(__vsock_bind_stream) prior to the change 'VSOCK: bind to random port for
VMADDR_PORT_ANY' would start walking up from LAST_RESERVED_PORT (1023) and
start assigning ports. That will take a large number of iterations to hit
0x7FFFFFFF. But, after the above change to randomize port selection, the
issue has started coming up more frequently.
There has really been no good reason to have this port reservation logic
in hv_sock from the get go. Reserving a local port for peer ports is not
how things are handled generally. Peer ports should reflect the peer port.
This fixes the issue by lifting the port reservation, and also returns the
right peer port. Since the code converts the GUID to the peer port (by
using the first 4 bytes), there is a possibility of conflicts, but that
seems like a reasonable risk to take, given this is limited to vsock and
that only applies to all local sockets.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in ptp_clock_unregister(), where ptp_cleanup_pin_groups()
first frees ptp->pin_{,dev_}attr, but then posix_clock_unregister() needs
them to destroy a related sysfs device.
These functions can not be just swapped, as posix_clock_unregister() frees
ptp which is needed in the ptp_cleanup_pin_groups(). Fix this by calling
ptp_cleanup_pin_groups() in ptp_clock_release(), right before ptp is freed.
This makes this patch fix an UAF bug in a patch which fixes an UAF bug.
Reported-by: Antti Laakso <antti.laakso@intel.com>
Fixes: a33121e548 ("ptp: fix the race between the release of ptp_clock and cdev")
Link: https://lore.kernel.org/netdev/3d2bd09735dbdaf003585ca376b7c1e5b69a19bd.camel@intel.com/
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Why]
When change the connection status in a MST topology, mst device
which detect the event will send out CONNECTION_STATUS_NOTIFY messgae.
e.g. src-mst-mst-sst => src-mst (unplug) mst-sst
Currently, under the above case of unplugging device, ports which have
been allocated payloads and are no longer in the topology still occupy
time slots and recorded in proposed_vcpi[] of topology manager.
If we don't clean up the proposed_vcpi[], when code flow goes to try to
update payload table by calling drm_dp_update_payload_part1(), we will
fail at checking port validation due to there are ports with proposed
time slots but no longer in the mst topology. As the result of that, we
will also stop updating the DPCD payload table of down stream port.
[How]
While handling the CONNECTION_STATUS_NOTIFY message, add a detection to
see if the event indicates that a device is unplugged to an output port.
If the detection is true, then iterrate over all proposed_vcpi[] to
see whether a port of the proposed_vcpi[] is still in the topology or
not. If the port is invalid, set its num_slots to 0.
Thereafter, when try to update payload table by calling
drm_dp_update_payload_part1(), we can successfully update the DPCD
payload table of down stream port and clear the proposed_vcpi[] to NULL.
Changes since v1:(https://patchwork.kernel.org/patch/11275801/)
* Invert the conditional to reduce the indenting
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
[removed cc for stable - there's too many patches this depends on for
this to backport cleanly]
Link: https://patchwork.freedesktop.org/patch/msgid/20200106102158.28261-1-Wayne.Lin@amd.com
Since v5.4, a device removal occasionally triggered this oops:
Dec 2 17:13:53 manet kernel: BUG: unable to handle page fault for address: 0000000c00000219
Dec 2 17:13:53 manet kernel: #PF: supervisor read access in kernel mode
Dec 2 17:13:53 manet kernel: #PF: error_code(0x0000) - not-present page
Dec 2 17:13:53 manet kernel: PGD 0 P4D 0
Dec 2 17:13:53 manet kernel: Oops: 0000 [#1] SMP
Dec 2 17:13:53 manet kernel: CPU: 2 PID: 468 Comm: kworker/2:1H Tainted: G W 5.4.0-00050-g53717e43af61 #883
Dec 2 17:13:53 manet kernel: Hardware name: Supermicro SYS-6028R-T/X10DRi, BIOS 1.1a 10/16/2015
Dec 2 17:13:53 manet kernel: Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
Dec 2 17:13:53 manet kernel: RIP: 0010:rpcrdma_wc_receive+0x7c/0xf6 [rpcrdma]
Dec 2 17:13:53 manet kernel: Code: 6d 8b 43 14 89 c1 89 45 78 48 89 4d 40 8b 43 2c 89 45 14 8b 43 20 89 45 18 48 8b 45 20 8b 53 14 48 8b 30 48 8b 40 10 48 8b 38 <48> 8b 87 18 02 00 00 48 85 c0 75 18 48 8b 05 1e 24 c4 e1 48 85 c0
Dec 2 17:13:53 manet kernel: RSP: 0018:ffffc900035dfe00 EFLAGS: 00010246
Dec 2 17:13:53 manet kernel: RAX: ffff888467290000 RBX: ffff88846c638400 RCX: 0000000000000048
Dec 2 17:13:53 manet kernel: RDX: 0000000000000048 RSI: 00000000f942e000 RDI: 0000000c00000001
Dec 2 17:13:53 manet kernel: RBP: ffff888467611b00 R08: ffff888464e4a3c4 R09: 0000000000000000
Dec 2 17:13:53 manet kernel: R10: ffffc900035dfc88 R11: fefefefefefefeff R12: ffff888865af4428
Dec 2 17:13:53 manet kernel: R13: ffff888466023000 R14: ffff88846c63f000 R15: 0000000000000010
Dec 2 17:13:53 manet kernel: FS: 0000000000000000(0000) GS:ffff88846fa80000(0000) knlGS:0000000000000000
Dec 2 17:13:53 manet kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Dec 2 17:13:53 manet kernel: CR2: 0000000c00000219 CR3: 0000000002009002 CR4: 00000000001606e0
Dec 2 17:13:53 manet kernel: Call Trace:
Dec 2 17:13:53 manet kernel: __ib_process_cq+0x5c/0x14e [ib_core]
Dec 2 17:13:53 manet kernel: ib_cq_poll_work+0x26/0x70 [ib_core]
Dec 2 17:13:53 manet kernel: process_one_work+0x19d/0x2cd
Dec 2 17:13:53 manet kernel: ? cancel_delayed_work_sync+0xf/0xf
Dec 2 17:13:53 manet kernel: worker_thread+0x1a6/0x25a
Dec 2 17:13:53 manet kernel: ? cancel_delayed_work_sync+0xf/0xf
Dec 2 17:13:53 manet kernel: kthread+0xf4/0xf9
Dec 2 17:13:53 manet kernel: ? kthread_queue_delayed_work+0x74/0x74
Dec 2 17:13:53 manet kernel: ret_from_fork+0x24/0x30
The proximal cause is that this rpcrdma_rep has a rr_rdmabuf that
is still pointing to the old ib_device, which has been freed. The
only way that is possible is if this rpcrdma_rep was not destroyed
by rpcrdma_ia_remove.
Debugging showed that was indeed the case: this rpcrdma_rep was
still in use by a completing RPC at the time of the device removal,
and thus wasn't on the rep free list. So, it was not found by
rpcrdma_reps_destroy().
The fix is to introduce a list of all rpcrdma_reps so that they all
can be found when a device is removed. That list is used to perform
only regbuf DMA unmapping, replacing that call to
rpcrdma_reps_destroy().
Meanwhile, to prevent corruption of this list, I've moved the
destruction of temp rpcrdma_rep objects to rpcrdma_post_recvs().
rpcrdma_xprt_drain() ensures that post_recvs (and thus rep_destroy) is
not invoked while rpcrdma_reps_unmap is walking rb_all_reps, thus
protecting the rb_all_reps list.
Fixes: b0b227f071 ("xprtrdma: Use an llist to manage free rpcrdma_reps")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
I've found that on occasion, "rmmod <dev>" will hang while if an NFS
is under load.
Ensure that ri_remove_done is initialized only just before the
transport is woken up to force a close. This avoids the completion
possibly getting initialized again while the CM event handler is
waiting for a wake-up.
Fixes: bebd031866 ("xprtrdma: Support unplugging an HCA from under an NFS mount")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Pull parisc fixes from Helge Deller:
"A boot crash fix by Mike Rapoport and a printk fix by Krzysztof
Kozlowski"
* 'parisc-5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix map_pages() to actually populate upper directory
parisc: Use proper printk format for resource_size_t
Pull asm-generic fixes from Arnd Bergmann:
"Here are two bugfixes from Mike Rapoport, both fixing compile-time
errors for the nds32 architecture that were recently introduced"
* tag 'asm-generic-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
nds32: fix build failure caused by page table folding updates
asm-generic/nds32: don't redefine cacheflush primitives
Pull SCSI fixes from James Bottomley:
"Two simple fixes in the upper drivers (so both fairly core), one in
enclosures, which fixes replugging a device into an enclosure slot and
one in the disk driver which fixes revalidating a drive with
protection information (PI) to make it a non-PI drive ... previously
we were still remembering the old PI state.
Both fixed issues are quite rare in the field"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: enclosure: Fix stale device oops with hot replug
scsi: sd: Clear sdkp->protection_type if disk is reformatted without PI
Merge misc fixes from David Howells.
Two afs fixes and a key refcounting fix.
* dhowells:
afs: Fix afs_lookup() to not clobber the version on a new dentry
afs: Fix use-after-loss-of-ref
keys: Fix request_key() cache
Fix afs_lookup() to not clobber the version set on a new dentry by
afs_do_lookup() - especially as it's using the wrong version of the
version (we need to use the one given to us by whatever op the dir
contents correspond to rather than what's in the afs_vnode).
Fixes: 9dd0b82ef5 ("afs: Fix missing dentry data version updating")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
afs_lookup() has a tracepoint to indicate the outcome of
d_splice_alias(), passing it the inode to retrieve the fid from.
However, the function gave up its ref on that inode when it called
d_splice_alias(), which may have failed and dropped the inode.
Fix this by caching the fid.
Fixes: 80548b0399 ("afs: Add more tracepoints")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the key cached by request_key() and co. is cleaned up on exit(),
the code looks in the wrong task_struct, and so clears the wrong cache.
This leads to anomalies in key refcounting when doing, say, a kernel
build on an afs volume, that then trigger kasan to report a
use-after-free when the key is viewed in /proc/keys.
Fix this by making exit_creds() look in the passed-in task_struct rather
than in current (the task_struct cleanup code is deferred by RCU and
potentially run in another task).
Fixes: 7743c48e54 ("keys: Cache result of request_key*() temporarily in task_struct")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from Andrew Morton:
"11 mm fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: khugepaged: add trace status description for SCAN_PAGE_HAS_PRIVATE
mm: memcg/slab: call flush_memcg_workqueue() only if memcg workqueue is valid
mm/page-writeback.c: improve arithmetic divisions
mm/page-writeback.c: use div64_ul() for u64-by-unsigned-long divide
mm/page-writeback.c: avoid potential division by zero in wb_min_max_ratio()
mm, debug_pagealloc: don't rely on static keys too early
mm: memcg/slab: fix percpu slab vmstats flushing
mm/shmem.c: thp, shmem: fix conflict of above-47bit hint address and PMD alignment
mm/huge_memory.c: thp: fix conflict of above-47bit hint address and PMD alignment
mm/memory_hotplug: don't free usage map when removing a re-added early section
mm, thp: tweak reclaim/compaction effort of local-only and all-node allocations
When building ARCH=um with CONFIG_UML_X86=y and CONFIG_64BIT=y we get
the build errors:
drivers/misc/lkdtm/bugs.c: In function ‘lkdtm_UNSET_SMEP’:
drivers/misc/lkdtm/bugs.c:288:8: error: implicit declaration of function ‘native_read_cr4’ [-Werror=implicit-function-declaration]
cr4 = native_read_cr4();
^~~~~~~~~~~~~~~
drivers/misc/lkdtm/bugs.c:290:13: error: ‘X86_CR4_SMEP’ undeclared (first use in this function); did you mean ‘X86_FEATURE_SMEP’?
if ((cr4 & X86_CR4_SMEP) != X86_CR4_SMEP) {
^~~~~~~~~~~~
X86_FEATURE_SMEP
drivers/misc/lkdtm/bugs.c:290:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/misc/lkdtm/bugs.c:297:2: error: implicit declaration of function ‘native_write_cr4’; did you mean ‘direct_write_cr4’? [-Werror=implicit-function-declaration]
native_write_cr4(cr4);
^~~~~~~~~~~~~~~~
direct_write_cr4
So specify that this block of code should only build when
CONFIG_X86_64=y *AND* CONFIG_UML is unset.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20191213003522.66450-1-brendanhiggins@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the DOUBLE_FAULT test to always be available (so test harnesses
don't have to make exceptions more missing tests), and for the
arch-specific tests to "XFAIL" so that test harnesses can reason about
expected vs unexpected failures.
Fixes: b09511c253 ("lkdtm: Add a DOUBLE_FAULT crash type on x86")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/202001021226.751D3F869D@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the newly added code in the etm4x driver is inside of an #ifdef,
and some other code is outside of it, leading to a harmless warning when
CONFIG_CPU_PM is disabled:
drivers/hwtracing/coresight/coresight-etm4x.c:68:13: error: 'etm4_os_lock' defined but not used [-Werror=unused-function]
static void etm4_os_lock(struct etmv4_drvdata *drvdata)
^~~~~~~~~~~~
To avoid the warning and simplify the the #ifdef checks, use
IS_ENABLED() instead, so the compiler can drop the unused functions
without complaining.
Fixes: f188b5e76a ("coresight: etm4x: Save/restore state across CPU low power states")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixed capital 'f' in title]
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20191213223107.1484-2-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging
on open() or tiocmset() due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 309a057932 ("USB: opticon: add rts and cts support")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Cc: Martin Jansen <martin.jansen@opticon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The altsetting sanity check in set_sync_ep_implicit_fb_quirk() was
checking for there to be at least one altsetting but then went on to
access the second one, which may not exist.
This could lead to random slab data being used to initialise the sync
endpoint in snd_usb_add_endpoint().
Fixes: c75a8a7ae5 ("ALSA: snd-usb: add support for implicit feedback")
Fixes: ca10a7ebdf ("ALSA: usb-audio: FT C400 sync playback EP to capture EP")
Fixes: 5e35dc0338 ("ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204")
Fixes: 17f08b0d9a ("ALSA: usb-audio: add implicit fb quirk for Axe-Fx II")
Fixes: 103e962564 ("ALSA: usb-audio: simplify set_sync_ep_implicit_fb_quirk")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200114083953.1106-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit d96885e277 ("parisc: use pgtable-nopXd instead of
4level-fixup") converted PA-RISC to use folded page tables, but it missed
the conversion of pgd_populate() to pud_populate() in maps_pages()
function. This caused the upper page table directory to remain empty and
the system would crash as a result.
Using pud_populate() that actually populates the page table instead of
dummy pgd_populate() fixes the issue.
Fixes: d96885e277 ("parisc: use pgtable-nopXd instead of 4level-fixup")
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Jeroen Roovers <jer@gentoo.org>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Jeroen Roovers <jer@gentoo.org>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Helge Deller <deller@gmx.de>
resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):
arch/parisc/kernel/drivers.c: In function 'print_parisc_device':
arch/parisc/kernel/drivers.c:892:9: warning:
format '%p' expects argument of type 'void *',
but argument 4 has type 'resource_size_t {aka unsigned int}' [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
The driver was doing a synchronous uninterruptible bulk-transfer without
using a timeout. This could lead to the driver hanging on probe due to a
malfunctioning (or malicious) device until the device is physically
disconnected. While sleeping in probe the driver prevents other devices
connected to the same hub from being added to (or removed from) the bus.
An arbitrary limit of five seconds should be more than enough.
Fixes: dbafc28955 ("NFC: pn533: don't send USB data off of the stack")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge Intel Gen9 graphics fix from Akeem Abodunrin:
"Insufficient control flow in certain data structures for some Intel
Processors with Intel Processor Graphics may allow an unauthenticated
user to potentially enable information disclosure via local access
This provides mitigation for Gen9 hardware. Note that Gen8 is not
impacted due to a previously implemented workaround.
The mitigation involves using an existing hardware feature to forcibly
clear down all EU state at each context switch"
* tag 'Intel-CVE-2019-14615' of emailed bundle from Akeem G Abodunrin <akeem.g.abodunrin@intel.com>:
drm/i915/gen9: Clear residual context state on context switch
This patch fix the issue with fixed link. With fixed-link
device opening fails due to macb_phylink_connect not
handling fixed-link mode, in which case no MAC-PHY connection
is needed and phylink_connect return success (0), however
in current driver attempt is made to search and connect to
PHY even for fixed-link.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't need it, and if we have it, then the retry handler will attempt
to copy the non-existent iovec with the inline iovec, with a segment
count that doesn't make sense.
Fixes: f67676d160 ("io_uring: ensure async punted read/write requests copy iovec")
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When booting with amd_iommu=off, the following WARNING message
appears:
AMD-Vi: AMD IOMMU disabled on kernel command-line
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:2772 flush_workqueue+0x42e/0x450
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.5.0-rc3-amd-iommu #6
Hardware name: Lenovo ThinkSystem SR655-2S/7D2WRCZ000, BIOS D8E101L-1.00 12/05/2019
RIP: 0010:flush_workqueue+0x42e/0x450
Code: ff 0f 0b e9 7a fd ff ff 4d 89 ef e9 33 fe ff ff 0f 0b e9 7f fd ff ff 0f 0b e9 bc fd ff ff 0f 0b e9 a8 fd ff ff e8 52 2c fe ff <0f> 0b 31 d2 48 c7 c6 e0 88 c5 95 48 c7 c7 d8 ad f0 95 e8 19 f5 04
Call Trace:
kmem_cache_destroy+0x69/0x260
iommu_go_to_state+0x40c/0x5ab
amd_iommu_prepare+0x16/0x2a
irq_remapping_prepare+0x36/0x5f
enable_IR_x2apic+0x21/0x172
default_setup_apic_routing+0x12/0x6f
apic_intr_mode_init+0x1a1/0x1f1
x86_late_time_init+0x17/0x1c
start_kernel+0x480/0x53f
secondary_startup_64+0xb6/0xc0
---[ end trace 30894107c3749449 ]---
x2apic: IRQ remapping doesn't support X2APIC mode
x2apic disabled
The warning is caused by the calling of 'kmem_cache_destroy()'
in free_iommu_resources(). Here is the call path:
free_iommu_resources
kmem_cache_destroy
flush_memcg_workqueue
flush_workqueue
The root cause is that the IOMMU subsystem runs before the workqueue
subsystem, which the variable 'wq_online' is still 'false'. This leads
to the statement 'if (WARN_ON(!wq_online))' in flush_workqueue() is
'true'.
Since the variable 'memcg_kmem_cache_wq' is not allocated during the
time, it is unnecessary to call flush_memcg_workqueue(). This prevents
the WARNING message triggered by flush_workqueue().
Link: http://lkml.kernel.org/r/20200103085503.1665-1-ahuang12@lenovo.com
Fixes: 92ee383f6d ("mm: fix race between kmem_cache destroy, create and deactivate")
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Reported-by: Xiaochun Lee <lixc17@lenovo.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "use div64_ul() instead of div_u64() if the divisor is
unsigned long".
We were first inspired by commit b0ab99e773 ("sched: Fix possible divide
by zero in avg_atom () calculation"), then refer to the recently analyzed
mm code, we found this suspicious place.
201 if (min) {
202 min *= this_bw;
203 do_div(min, tot_bw);
204 }
And we also disassembled and confirmed it:
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 201
0xffffffff811c37da <__wb_calc_thresh+234>: xor %r10d,%r10d
0xffffffff811c37dd <__wb_calc_thresh+237>: test %rax,%rax
0xffffffff811c37e0 <__wb_calc_thresh+240>: je 0xffffffff811c3800 <__wb_calc_thresh+272>
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 202
0xffffffff811c37e2 <__wb_calc_thresh+242>: imul %r8,%rax
/usr/src/debug/kernel-4.9.168-016.ali3000/linux-4.9.168-016.ali3000.alios7.x86_64/mm/page-writeback.c: 203
0xffffffff811c37e6 <__wb_calc_thresh+246>: mov %r9d,%r10d ---> truncates it to 32 bits here
0xffffffff811c37e9 <__wb_calc_thresh+249>: xor %edx,%edx
0xffffffff811c37eb <__wb_calc_thresh+251>: div %r10
0xffffffff811c37ee <__wb_calc_thresh+254>: imul %rbx,%rax
0xffffffff811c37f2 <__wb_calc_thresh+258>: shr $0x2,%rax
0xffffffff811c37f6 <__wb_calc_thresh+262>: mul %rcx
0xffffffff811c37f9 <__wb_calc_thresh+265>: shr $0x2,%rdx
0xffffffff811c37fd <__wb_calc_thresh+269>: mov %rdx,%r10
This series uses div64_ul() instead of div_u64() if the divisor is
unsigned long, to avoid truncation to 32-bit on 64-bit platforms.
This patch (of 3):
The variables 'min' and 'max' are unsigned long and do_div truncates
them to 32 bits, which means it can test non-zero and be truncated to
zero for division. Fix this issue by using div64_ul() instead.
Link: http://lkml.kernel.org/r/20200102081442.8273-2-wenyang@linux.alibaba.com
Fixes: 693108a8a6 ("writeback: make bdi->min/max_ratio handling cgroup writeback aware")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 96a2b03f28 ("mm, debug_pagelloc: use static keys to enable
debugging") has introduced a static key to reduce overhead when
debug_pagealloc is compiled in but not enabled. It relied on the
assumption that jump_label_init() is called before parse_early_param()
as in start_kernel(), so when the "debug_pagealloc=on" option is parsed,
it is safe to enable the static key.
However, it turns out multiple architectures call parse_early_param()
earlier from their setup_arch(). x86 also calls jump_label_init() even
earlier, so no issue was found while testing the commit, but same is not
true for e.g. ppc64 and s390 where the kernel would not boot with
debug_pagealloc=on as found by our QA.
To fix this without tricky changes to init code of multiple
architectures, this patch partially reverts the static key conversion
from 96a2b03f28. Init-time and non-fastpath calls (such as in arch
code) of debug_pagealloc_enabled() will again test a simple bool
variable. Fastpath mm code is converted to a new
debug_pagealloc_enabled_static() variant that relies on the static key,
which is enabled in a well-defined point in mm_init() where it's
guaranteed that jump_label_init() has been called, regardless of
architecture.
[sfr@canb.auug.org.au: export _debug_pagealloc_enabled_early]
Link: http://lkml.kernel.org/r/20200106164944.063ac07b@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191219130612.23171-1-vbabka@suse.cz
Fixes: 96a2b03f28 ("mm, debug_pagelloc: use static keys to enable debugging")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Qian Cai <cai@lca.pw>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently slab percpu vmstats are flushed twice: during the memcg
offlining and just before freeing the memcg structure. Each time percpu
counters are summed, added to the atomic counterparts and propagated up
by the cgroup tree.
The second flushing is required due to how recursive vmstats are
implemented: counters are batched in percpu variables on a local level,
and once a percpu value is crossing some predefined threshold, it spills
over to atomic values on the local and each ascendant levels. It means
that without flushing some numbers cached in percpu variables will be
dropped on floor each time a cgroup is destroyed. And with uptime the
error on upper levels might become noticeable.
The first flushing aims to make counters on ancestor levels more
precise. Dying cgroups may resume in the dying state for a long time.
After kmem_cache reparenting which is performed during the offlining
slab counters of the dying cgroup don't have any chances to be updated,
because any slab operations will be performed on the parent level. It
means that the inaccuracy caused by percpu batching will not decrease up
to the final destruction of the cgroup. By the original idea flushing
slab counters during the offlining should minimize the visible
inaccuracy of slab counters on the parent level.
The problem is that percpu counters are not zeroed after the first
flushing. So every cached percpu value is summed twice. It creates a
small error (up to 32 pages per cpu, but usually less) which accumulates
on parent cgroup level. After creating and destroying of thousands of
child cgroups, slab counter on parent level can be way off the real
value.
For now, let's just stop flushing slab counters on memcg offlining. It
can't be done correctly without scheduling a work on each cpu: reading
and zeroing it during css offlining can race with an asynchronous
update, which doesn't expect values to be changed underneath.
With this change, slab counters on parent level will become eventually
consistent. Once all dying children are gone, values are correct. And
if not, the error is capped by 32 * NR_CPUS pages per dying cgroup.
It's not perfect, as slab are reparented, so any updates after the
reparenting will happen on the parent level. It means that if a slab
page was allocated, a counter on child level was bumped, then the page
was reparented and freed, the annihilation of positive and negative
counter values will not happen until the child cgroup is released. It
makes slab counters different from others, and it might want us to
implement flushing in a correct form again. But it's also a question of
performance: scheduling a work on each cpu isn't free, and it's an open
question if the benefit of having more accurate counters is worth it.
We might also consider flushing all counters on offlining, not only slab
counters.
So let's fix the main problem now: make the slab counters eventually
consistent, so at least the error won't grow with uptime (or more
precisely the number of created and destroyed cgroups). And think about
the accuracy of counters separately.
Link: http://lkml.kernel.org/r/20191220042728.1045881-1-guro@fb.com
Fixes: bee07b33db ("mm: memcontrol: flush percpu slab vmstats on kmem offlining")
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shmem/tmpfs tries to provide THP-friendly mappings if huge pages are
enabled. But it doesn't work well with above-47bit hint address.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks THP alignment in shmem/tmp:
shmem_get_unmapped_area() would not try to allocate PMD-aligned area if
*any* hint address specified.
This can be fixed by requesting the aligned area if the we failed to
allocated at user-specified hint address. The request with inflated
length will also take the user-specified hint address. This way we will
not lose an allocation request from the full address space.
[kirill@shutemov.name: fold in a fixup]
Link: http://lkml.kernel.org/r/20191223231309.t6bh5hkbmokihpfu@box
Link: http://lkml.kernel.org/r/20191220142548.7118-3-kirill.shutemov@linux.intel.com
Fixes: b569bab78d ("x86/mm: Prepare to expose larger address space to userspace")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Willhalm, Thomas" <thomas.willhalm@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Fix two above-47bit hint address vs. THP bugs".
The two get_unmapped_area() implementations have to be fixed to provide
THP-friendly mappings if above-47bit hint address is specified.
This patch (of 2):
Filesystems use thp_get_unmapped_area() to provide THP-friendly
mappings. For DAX in particular.
Normally, the kernel doesn't create userspace mappings above 47-bit,
even if the machine allows this (such as with 5-level paging on x86-64).
Not all user space is ready to handle wide addresses. It's known that
at least some JIT compilers use higher bits in pointers to encode their
information.
Userspace can ask for allocation from full address space by specifying
hint address (with or without MAP_FIXED) above 47-bits. If the
application doesn't need a particular address, but wants to allocate
from whole address space it can specify -1 as a hint address.
Unfortunately, this trick breaks thp_get_unmapped_area(): the function
would not try to allocate PMD-aligned area if *any* hint address
specified.
Modify the routine to handle it correctly:
- Try to allocate the space at the specified hint address with length
padding required for PMD alignment.
- If failed, retry without length padding (but with the same hint
address);
- If the returned address matches the hint address return it.
- Otherwise, align the address as required for THP and return.
The user specified hint address is passed down to get_unmapped_area() so
above-47bit hint address will be taken into account without breaking
alignment requirements.
Link: http://lkml.kernel.org/r/20191220142548.7118-2-kirill.shutemov@linux.intel.com
Fixes: b569bab78d ("x86/mm: Prepare to expose larger address space to userspace")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Thomas Willhalm <thomas.willhalm@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Bruggeman, Otto G" <otto.g.bruggeman@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we remove an early section, we don't free the usage map, as the
usage maps of other sections are placed into the same page. Once the
section is removed, it is no longer an early section (especially, the
memmap is freed). When we re-add that section, the usage map is reused,
however, it is no longer an early section. When removing that section
again, we try to kfree() a usage map that was allocated during early
boot - bad.
Let's check against PageReserved() to see if we are dealing with an
usage map that was allocated during boot. We could also check against
!(PageSlab(usage_page) || PageCompound(usage_page)), but PageReserved() is
cleaner.
Can be triggered using memtrace under ppc64/powernv:
$ mount -t debugfs none /sys/kernel/debug/
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
$ echo 0x20000000 > /sys/kernel/debug/powerpc/memtrace/enable
------------[ cut here ]------------
kernel BUG at mm/slub.c:3969!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=3D64K MMU=3DHash SMP NR_CPUS=3D2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 154 Comm: sh Not tainted 5.5.0-rc2-next-20191216-00005-g0be1dba7b7c0 #61
NIP kfree+0x338/0x3b0
LR section_deactivate+0x138/0x200
Call Trace:
section_deactivate+0x138/0x200
__remove_pages+0x114/0x150
arch_remove_memory+0x3c/0x160
try_remove_memory+0x114/0x1a0
__remove_memory+0x20/0x40
memtrace_enable_set+0x254/0x850
simple_attr_write+0x138/0x160
full_proxy_write+0x8c/0x110
__vfs_write+0x38/0x70
vfs_write+0x11c/0x2a0
ksys_write+0x84/0x140
system_call+0x5c/0x68
---[ end trace 4b053cbd84e0db62 ]---
The first invocation will offline+remove memory blocks. The second
invocation will first add+online them again, in order to offline+remove
them again (usually we are lucky and the exact same memory blocks will
get "reallocated").
Tested on powernv with boot memory: The usage map will not get freed.
Tested on x86-64 with DIMMs: The usage map will get freed.
Using Dynamic Memory under a Power DLAPR can trigger it easily.
Triggering removal (I assume after previously removed+re-added) of
memory from the HMC GUI can crash the kernel with the same call trace
and is fixed by this patch.
Link: http://lkml.kernel.org/r/20191217104637.5509-1-david@redhat.com
Fixes: 326e1b8f83 ("mm/sparsemem: introduce a SECTION_IS_EARLY flag")
Signed-off-by: David Hildenbrand <david@redhat.com>
Tested-by: Pingfan Liu <piliu@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
THP page faults now attempt a __GFP_THISNODE allocation first, which
should only compact existing free memory, followed by another attempt
that can allocate from any node using reclaim/compaction effort
specified by global defrag setting and madvise.
This patch makes the following changes to the scheme:
- Before the patch, the first allocation relies on a check for
pageblock order and __GFP_IO to prevent excessive reclaim. This
however affects also the second attempt, which is not limited to
single node.
Instead of that, reuse the existing check for costly order
__GFP_NORETRY allocations, and make sure the first THP attempt uses
__GFP_NORETRY. As a side-effect, all costly order __GFP_NORETRY
allocations will bail out if compaction needs reclaim, while
previously they only bailed out when compaction was deferred due to
previous failures.
This should be still acceptable within the __GFP_NORETRY semantics.
- Before the patch, the second allocation attempt (on all nodes) was
passing __GFP_NORETRY. This is redundant as the check for pageblock
order (discussed above) was stronger. It's also contrary to
madvise(MADV_HUGEPAGE) which means some effort to allocate THP is
requested.
After this patch, the second attempt doesn't pass __GFP_THISNODE nor
__GFP_NORETRY.
To sum up, THP page faults now try the following attempts:
1. local node only THP allocation with no reclaim, just compaction.
2. for madvised VMA's or when synchronous compaction is enabled always - THP
allocation from any node with effort determined by global defrag setting
and VMA madvise
3. fallback to base pages on any node
Link: http://lkml.kernel.org/r/08a3f4dd-c3ce-0009-86c5-9ee51aba8557@suse.cz
Fixes: b39d0ee263 ("mm, page_alloc: avoid expensive reclaim when compaction may not succeed")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[BUG]
There are several different KASAN reports for balance + snapshot
workloads. Involved call paths include:
should_ignore_root+0x54/0xb0 [btrfs]
build_backref_tree+0x11af/0x2280 [btrfs]
relocate_tree_blocks+0x391/0xb80 [btrfs]
relocate_block_group+0x3e5/0xa00 [btrfs]
btrfs_relocate_block_group+0x240/0x4d0 [btrfs]
btrfs_relocate_chunk+0x53/0xf0 [btrfs]
btrfs_balance+0xc91/0x1840 [btrfs]
btrfs_ioctl_balance+0x416/0x4e0 [btrfs]
btrfs_ioctl+0x8af/0x3e60 [btrfs]
do_vfs_ioctl+0x831/0xb10
create_reloc_root+0x9f/0x460 [btrfs]
btrfs_reloc_post_snapshot+0xff/0x6c0 [btrfs]
create_pending_snapshot+0xa9b/0x15f0 [btrfs]
create_pending_snapshots+0x111/0x140 [btrfs]
btrfs_commit_transaction+0x7a6/0x1360 [btrfs]
btrfs_mksubvol+0x915/0x960 [btrfs]
btrfs_ioctl_snap_create_transid+0x1d5/0x1e0 [btrfs]
btrfs_ioctl_snap_create_v2+0x1d3/0x270 [btrfs]
btrfs_ioctl+0x241b/0x3e60 [btrfs]
do_vfs_ioctl+0x831/0xb10
btrfs_reloc_pre_snapshot+0x85/0xc0 [btrfs]
create_pending_snapshot+0x209/0x15f0 [btrfs]
create_pending_snapshots+0x111/0x140 [btrfs]
btrfs_commit_transaction+0x7a6/0x1360 [btrfs]
btrfs_mksubvol+0x915/0x960 [btrfs]
btrfs_ioctl_snap_create_transid+0x1d5/0x1e0 [btrfs]
btrfs_ioctl_snap_create_v2+0x1d3/0x270 [btrfs]
btrfs_ioctl+0x241b/0x3e60 [btrfs]
do_vfs_ioctl+0x831/0xb10
[CAUSE]
All these call sites are only relying on root->reloc_root, which can
undergo btrfs_drop_snapshot(), and since we don't have real refcount
based protection to reloc roots, we can reach already dropped reloc
root, triggering KASAN.
[FIX]
To avoid such access to unstable root->reloc_root, we should check
BTRFS_ROOT_DEAD_RELOC_TREE bit first.
This patch introduces wrappers that provide the correct way to check the
bit with memory barriers protection.
Most callers don't distinguish merged reloc tree and no reloc tree. The
only exception is should_ignore_root(), as merged reloc tree can be
ignored, while no reloc tree shouldn't.
[CRITICAL SECTION ANALYSIS]
Although test_bit()/set_bit()/clear_bit() doesn't imply a barrier, the
DEAD_RELOC_TREE bit has extra help from transaction as a higher level
barrier, the lifespan of root::reloc_root and DEAD_RELOC_TREE bit are:
NULL: reloc_root is NULL PTR: reloc_root is not NULL
0: DEAD_RELOC_ROOT bit not set DEAD: DEAD_RELOC_ROOT bit set
(NULL, 0) Initial state __
| /\ Section A
btrfs_init_reloc_root() \/
| __
(PTR, 0) reloc_root initialized /\
| |
btrfs_update_reloc_root() | Section B
| |
(PTR, DEAD) reloc_root has been merged \/
| __
=== btrfs_commit_transaction() ====================
| /\
clean_dirty_subvols() |
| | Section C
(NULL, DEAD) reloc_root cleanup starts \/
| __
btrfs_drop_snapshot() /\
| | Section D
(NULL, 0) Back to initial state \/
Every have_reloc_root() or test_bit(DEAD_RELOC_ROOT) caller holds
transaction handle, so none of such caller can cross transaction boundary.
In Section A, every caller just found no DEAD bit, and grab reloc_root.
In the cross section A-B, caller may get no DEAD bit, but since reloc_root
is still completely valid thus accessing reloc_root is completely safe.
No test_bit() caller can cross the boundary of Section B and Section C.
In Section C, every caller found the DEAD bit, so no one will access
reloc_root.
In the cross section C-D, either caller gets the DEAD bit set, avoiding
access reloc_root no matter if it's safe or not. Or caller get the DEAD
bit cleared, then access reloc_root, which is already NULL, nothing will
be wrong.
The memory write barriers are between the reloc_root updates and bit
set/clear, the pairing read side is before test_bit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Fixes: d2311e6985 ("btrfs: relocation: Delay reloc tree deletion after merge_reloc_roots")
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ barriers ]
Signed-off-by: David Sterba <dsterba@suse.com>
Fix attribute name from "jtag_enable", which described twice to
"cpld3_version", which is expected to be instead of second appearance
of "jtag_enable".
Fixes: 2752e34442 ("Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
An earlier commit (1b789577f6,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:xt_rateest_put+0xa1/0x440 net/netfilter/xt_RATEEST.c:77
xt_rateest_tg_destroy+0x72/0xa0 net/netfilter/xt_RATEEST.c:175
cleanup_entry net/ipv4/netfilter/arp_tables.c:509 [inline]
translate_table+0x11f4/0x1d80 net/ipv4/netfilter/arp_tables.c:587
do_replace net/ipv4/netfilter/arp_tables.c:981 [inline]
do_arpt_set_ctl+0x317/0x650 net/ipv4/netfilter/arp_tables.c:1461
Also init the netns pointer in xt_tgdtor_param struct.
Fixes: add6746124 ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+91bdd8eece0f6629ec8b@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull Allwinner clk fixes from Maxime Ripard:
Our usual set of fixes for Allwinner, to fix the number of reported
clocks on the v3s, fixing the external clock on the R40, and some
fixes for the AR100 co-processor clocks.
* tag 'sunxi-clk-fixes-for-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.
So far I was not able to reproduce the problem when using lpass-cpu.
The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.
Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().
Fixes: 150db8c5af ("ASoC: codecs: Add msm8916-wcd digital codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().
But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.
Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In case system has multiple HDA codecs, and codec probe fails for
at least one but not all codecs, driver will end up cancelling
a non-initialized timer context upon driver removal.
Call trace of typical case:
[ 60.593646] WARNING: CPU: 1 PID: 1147 at kernel/workqueue.c:3032
__flush_work+0x18b/0x1a0
[...]
[ 60.593670] __cancel_work_timer+0x11f/0x1a0
[ 60.593673] hdac_hda_dev_remove+0x25/0x30 [snd_soc_hdac_hda]
[ 60.593674] device_release_driver_internal+0xe0/0x1c0
[ 60.593675] bus_remove_device+0xd6/0x140
[ 60.593677] device_del+0x175/0x3e0
[ 60.593679] ? widget_tree_free.isra.7+0x90/0xb0 [snd_hda_core]
[ 60.593680] snd_hdac_device_unregister+0x34/0x50 [snd_hda_core]
[ 60.593682] snd_hdac_ext_bus_device_remove+0x2a/0x60 [snd_hda_ext_core]
[ 60.593684] hda_dsp_remove+0x26/0x100 [snd_sof_intel_hda_common]
[ 60.593686] snd_sof_device_remove+0x84/0xa0 [snd_sof]
[ 60.593687] sof_pci_remove+0x10/0x30 [snd_sof_pci]
[ 60.593689] pci_device_remove+0x36/0xb0
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.
SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.
Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().
Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous versions of `iio_compute_scan_bytes` only aligned each element
to its own length (i.e. its own natural alignment). Because multiple
consecutive sets of scan elements are buffered this does not work in
case the computed scan bytes do not align with the natural alignment of
the first scan element in the set.
This commit fixes this by aligning the scan bytes to the natural
alignment of the largest scan element in the set.
Fixes: 959d2952d1 ("staging:iio: make iio_sw_buffer_preenable much more general.")
Signed-off-by: Lars Möllendorf <lars.moellendorf@plating.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO triggered buffer depends on IIO buffer which is missing from Kconfig
file. This should go unnoticed most of the time because there's a
chance something else has already enabled buffers. In some rare cases
though one might experience kbuild warnings about unmet direct
dependencies and build failures due to missing symbols.
Fix this by selecting IIO_BUFFER explicitly.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, attempting to probe a device with ST_LSM6DS3_ID
(e.g. using the st,lsm6ds3 compatible) fails with:
st_lsm6dsx_i2c 1-006b: unsupported whoami [69]
... even though 0x69 is the whoami listed for ST_LSM6DS3_ID.
This happens because st_lsm6dsx_check_whoami() also attempts
to match unspecified (zero-initialized) entries in the "id" array.
ST_LSM6DS3_ID = 0 will therefore match any entry in
st_lsm6dsx_sensor_settings (here: the first), because none of them
actually have all 12 entries listed in the "id" array.
Avoid this by additionally checking if "name" is set,
which is only set for valid entries in the "id" array.
Note: Although the problem was introduced earlier it did not surface until
commit 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
because ST_LSM6DS3_ID was the first entry in st_lsm6dsx_sensor_settings.
Fixes: d068e4a0f9 ("iio: imu: st_lsm6dsx: add support to multiple devices with the same settings")
Cc: <stable@vger.kernel.org> # 5.4
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes device tree channel configuration.
ad7124 driver reads channels configuration from the device tree.
It expects to find channel specifications as child nodes.
Before this patch ad7124 driver assumed that the child nodes are parsed
by for_each_available_child_of_node in the order 0,1,2,3...
This is wrong and the real order of the children can be seen by running:
dtc -I fs /sys/firmware/devicetree/base on the machine.
For example, running this on an rpi 3B+ yields the real
children order: 4,2,0,7,5,3,1,6
Before this patch the driver assigned the channel configuration
like this:
- 0 <- 4
- 1 <- 2
- 2 <- 0
........
For example, the symptoms can be observed by connecting the 4th channel
to a 1V tension and then reading the in_voltage0-voltage19_raw sysfs
(multiplied of course by the scale) one would see that channel 0
measures 1V and channel 4 measures only noise.
Now the driver uses the reg property of each child in order to
correctly identify to which channel the parsed configuration
belongs to.
Fixes b3af341bbd: ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b96 ("asus-wmi: add keyboard backlight support")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Allow the user to configure the fan to turn on / speed-up at lower
thresholds then before (20 degrees Celcius as minimum instead of 40) and
likewise also allow the user to delay the fan speeding-up till the
temperature hits 90 degrees Celcius (was 70).
Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use our default values when wrong module-parameters are given, instead of
refusing to load. Refusing to load leaves the fan at the BIOS default
setting, which is "Off". The CPU's thermal throttling should protect the
system from damage, but not-loading is really not the best fallback in this
case.
This commit fixes this by re-setting module-parameter values to their
defaults if they are out of range, instead of failing the probe with
-EINVAL.
Cc: stable@vger.kernel.org
Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Fixes: 594ce6db32 ("platform/x86: GPD pocket fan: Use a min-speed of 2 while charging")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This commit fixes the potential deadlock caused by the console Rx
and Tx processing at the same time. Rx and Tx both take the console
and tmfifo spinlock but in different order which causes potential
deadlock. The fix is to use different tmfifo spinlock for Rx and
Tx since they protect different resources and it's safe to split
the lock.
Below is the reported call trace when copying/pasting large string
in the console.
Rx:
_raw_spin_lock_irqsave (hvc lock)
__hvc_poll
hvc_poll
in_intr
vring_interrupt
mlxbf_tmfifo_rxtx_one_desc (tmfifo lock)
mlxbf_tmfifo_rxtx
mlxbf_tmfifo_work_rxtx
Tx:
_raw_spin_lock_irqsave (tmfifo lock)
mlxbf_tmfifo_virtio_notify
virtqueue_notify
virtqueue_kick
put_chars
hvc_push
hvc_write (hvc lock)
...
do_tty_write
tty_write
Fixes: 1357dfd726 ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Cc: <stable@vger.kernel.org> # 5.4+
Reviewed-by: David Woods <dwoods@mellanox.com>
Signed-off-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch corrects the SPDX License Identifier style in
header files related to x86 Platform Specific Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pull RISC-V fixes from Paul Walmsley:
"Two fixes for RISC-V:
- Clear FP registers during boot when FP support is present, rather
than when they aren't present
- Move the header files associated with the SiFive L2 cache
controller to drivers/soc (where the code was recently moved)"
* tag 'riscv/for-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fixup obvious bug for fp-regs reset
riscv: move sifive_l2_cache.h to include/soc
CSR_MISA is defined in Privileged Architectures' spec: 3.1.1 Machine
ISA Register misa. Every bit:1 indicate a feature, so we should beqz
reset_done when there is no F/D bit in csr_misa register.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
[paul.walmsley@sifive.com: fix typo in commit message]
Fixes: 9e80635619 ("riscv: clear the instruction cache and all registers when booting")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Pull iommu fixes from Joerg Roedel:
- Two fixes for VT-d and generic IOMMU code to fix teardown on error
handling code paths.
- Patch for the Intel VT-d driver to fix handling of non-PCI devices
- Fix W=1 compile warning in dma-iommu code
* tag 'iommu-fixes-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: fix variable 'cookie' set but not used
iommu/vt-d: Unlink device if failed to add to group
iommu: Remove device link to group on failure
iommu/vt-d: Fix adding non-PCI devices to Intel IOMMU
For plain text output, it incorrectly prints the pointer value
"void *data". The "void *data" is actually pointing to memory that
contains a bpf-map's value. The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.
In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".
Fixes: 22c349e8db ("tools: bpftool: fix format strings and arguments for jsonw_printf()")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Link: https://lore.kernel.org/bpf/20200110231644.3484151-1-kafai@fb.com
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes, a documentation fix, and a removal of a spec
violation for the bus recovery algorithm in the core"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: fix bus recovery stop mode timing
i2c: bcm2835: Store pointer to bus clock
dt-bindings: i2c: at91: fix i2c-sda-hold-time-ns documentation for sam9x60
i2c: at91: fix clk_offset for sam9x60
Pull thread fixes from Christian Brauner:
"This contains a series of patches to fix CLONE_SETTLS when used with
clone3().
The clone3() syscall passes the tls argument through struct clone_args
instead of a register. This means, all architectures that do not
implement copy_thread_tls() but still support CLONE_SETTLS via
copy_thread() expecting the tls to be located in a register argument
based on clone() are currently unfortunately broken. Their tls value
will be garbage.
The patch series fixes this on all architectures that currently define
__ARCH_WANT_SYS_CLONE3. It also adds a compile-time check to ensure
that any architecture that enables clone3() in the future is forced to
also implement copy_thread_tls().
My ultimate goal is to get rid of the copy_thread()/copy_thread_tls()
split and just have copy_thread_tls() at some point in the not too
distant future (Maybe even renaming copy_thread_tls() back to simply
copy_thread() once the old function is ripped from all arches). This
is dependent now on all arches supporting clone3().
While all relevant arches do that now there are still four missing:
ia64, m68k, sh and sparc. They have the system call reserved, but not
implemented. Once they all implement clone3() we can get rid of
ARCH_WANT_SYS_CLONE3 and HAVE_COPY_THREAD_TLS.
This series also includes a minor fix for the arm64 uapi headers which
caused __NR_clone3 to be missing from the exported user headers.
Unfortunately the series came in a little late especially given that
it touches a range of architectures. Due to the holidays not all arch
maintainers responded in time probably due to their backlog. Will and
Arnd have thankfully acked the arm specific changes.
Given that the changes are straightforward and rather minimal combined
with the fact the that clone3() with CLONE_SETTLS is broken I decided
to send them post rc3 nonetheless"
* tag 'clone3-tls-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
um: Implement copy_thread_tls
clone3: ensure copy_thread_tls is implemented
xtensa: Implement copy_thread_tls
riscv: Implement copy_thread_tls
parisc: Implement copy_thread_tls
arm: Implement copy_thread_tls
arm64: Implement copy_thread_tls
arm64: Move __ARCH_WANT_SYS_CLONE3 definition to uapi headers
My Netronome email address may become inactive soon.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of locations accidentally misspelled snapshot as shapshot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've got quite a few bug reports showing the SOF driver being loaded
unintentionally recently, and the reason seems to be that users didn't
know the module option change: with the recent kernel, a new option
dsp_driver=1 has to be passed to a new module snd-intel-dspcfg
instead of snd_hda_intel.dmic_detect=0 option.
That is, actually there are two tricky things here:
- We changed the whole detection in another module and another
option semantics.
- The existing option for skipping the DSP probe was also renamed.
For avoiding the confusion and giving user more hint, this patch
reverts the renamed option dsp_driver back to dmic_detect for
snd-hda-intel module, and show the warning about the module option
change when the non-default value is passed.
Fixes: 82d9d54a6c ("ALSA: hda: add Intel DSP configuration / probe code")
Link: https://lore.kernel.org/r/20200109082000.26729-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Murphy says:
====================
DP83822 and DP83TC811 Fixes
Two fixes on net/phy/Kconfig for the TI ethernet PHYs.
First fixed the typo in the Kconfig for the DP83TC811 where it incorretly stated
that the support was for a DP83TC822 which does not exist.
Second fix was to update the DP83822 Kconfig entry to indicate support for the
DP83825 devices in the description and the prompt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Kconfig description to indicate support for the DP83825I
device as well.
Fixes: 32b12dc8fde1 ("net: phy: Add DP83825I to the DP83822 driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in the Kconfig for the DP83TC811 as it indicates support for
the DP83TC822 which is incorrect.
Fixes: 6d749428788b {"net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A fix for the Beelink A1 IR receiver setting the correct polarity.
* tag 'v5.5-rockchip-dtsfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix IR on Beelink A1
Link: https://lore.kernel.org/r/2054603.JKFSmqfO19@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.5, round 2:
- Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
error seen with UART1.
- Correct compatible of RV3029 RTC device on imx6q-dhcom board.
- Correct interrupt trigger type for magnetometer on board
imx8mq-librem5-devkit.
- A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
development board.
- Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
that Ethernet interface on the board works properly.
- Fix Toradex Colibri board to get NAND flash support back.
- Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
is connected to PMIC SW2 output rather than a fixed 3V3 rail.
- Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
kernel.
- Fix endian setting for DCFG on LS1028A SoC, so that register access
of DCFG becomes correct.
* tag 'imx-fixes-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
arm64: dts: imx8mq-librem5-devkit: use correct interrupt for the magnetometer
ARM: dts: imx6q-dhcom: Fix SGTL5000 VDDIO regulator connection
ARM: dts: imx7ulp: fix reg of cpu node
arm64: dts: imx8mm: Change SDMA1 ahb clock for imx8mm
arm64: dts: ls1028a: fix endian setting for dcfg
ARM: dts: imx6q-dhcom: fix rtc compatible
Link: https://lore.kernel.org/r/20200110011836.GW4456@T480
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit cited below causes devlink to emit a warning if a type was
not set on a devlink port for longer than 30 seconds to "prevent
misbehavior of drivers". This proved to be problematic when
unregistering the backing netdev. The flow is always:
devlink_port_type_clear() // schedules the warning
unregister_netdev() // blocking
devlink_port_unregister() // cancels the warning
The call to unregister_netdev() can block for long periods of time for
various reasons: RTNL lock is contended, large amounts of configuration
to unroll following dismantle of the netdev, etc. This results in
devlink emitting a warning despite the driver behaving correctly.
In emulated environments (of future hardware) which are usually very
slow, the warning can also be emitted during port creation as more than
30 seconds can pass between the time the devlink port is registered and
when its type is set.
In addition, syzbot has hit this warning [1] 1974 times since 07/11/19
without being able to produce a reproducer. Probably because
reproduction depends on the load or other bugs (e.g., RTNL not being
released).
To prevent bogus warnings, increase the timeout to 1 hour.
[1] https://syzkaller.appspot.com/bug?id=e99b59e9c024a666c9f7450dc162a4b74d09d9cb
Fixes: 136bf27fc0 ("devlink: add warning in case driver does not set port type")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: syzbot+b0a18ed7b08b735d2f41@syzkaller.appspotmail.com
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EC on the Wilco platform responds with 0xFF to commands related to
the keyboard backlight on the absence of a keyboard backlight module.
This change allows the EC driver to continue loading even if the
backlight module is not present.
Fixes: 119a3cb6d6 ("platform/chrome: wilco_ec: Add keyboard backlight LED support")
Signed-off-by: Daniel Campello <campello@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull HID fix from Jiri Kosina:
"A regression fix for EPOLLOUT handling in hidraw and uhid"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: hidraw, uhid: Always report EPOLLOUT
Pull USB/PHY fixes from Greg KH:
"Here are a number of USB and PHY driver fixes for 5.5-rc6
Nothing all that unusual, just the a bunch of small fixes for a lot of
different reported issues. The PHY driver fixes are in here as they
interacted with the usb drivers.
Full details of the patches are in the shortlog, and all of these have
been in linux-next with no reported issues"
* tag 'usb-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (24 commits)
usb: missing parentheses in USE_NEW_SCHEME
usb: ohci-da8xx: ensure error return on variable error is set
usb: musb: Disable pullup at init
usb: musb: fix idling for suspend after disconnect interrupt
usb: typec: ucsi: Fix the notification bit offsets
USB: Fix: Don't skip endpoint descriptors with maxpacket=0
USB-PD tcpm: bad warning+size, PPS adapters
phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
usb: chipidea: host: Disable port power only if previously enabled
usb: cdns3: should not use the same dev_id for shared interrupt handler
usb: dwc3: gadget: Fix request complete check
usb: musb: dma: Correct parameter passed to IRQ handler
usb: musb: jz4740: Silence error if code is -EPROBE_DEFER
usb: udc: tegra: select USB_ROLE_SWITCH
USB: core: fix check for duplicate endpoints
phy: cpcap-usb: Drop extra write to usb2 register
phy: cpcap-usb: Improve host vs docked mode detection
phy: cpcap-usb: Prevent USB line glitches from waking up modem
phy: mapphone-mdm6600: Fix uninitialized status value regression
phy: cpcap-usb: Fix flakey host idling and enumerating of devices
...
Pull char/misc fix from Greg KH:
"Here is a single fix, for the chrdev core, for 5.5-rc6
There's been a long-standing race condition triggered by syzbot, and
occasionally real people, in the chrdev open() path. Will finally took
the time to track it down and fix it for real before the holidays.
Here's that one patch, it's been in linux-next for a while with no
reported issues and it does fix the reported problem"
* tag 'char-misc-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
chardev: Avoid potential use-after-free in 'chrdev_open()'
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 5.5-rc6.
Nothing major here, just some small fixes for a comedi driver, the
vt6656 driver, and a new device id for the rtl8188eu driver.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8188eu: Add device code for TP-Link TL-WN727N v5.21
staging: comedi: adv_pci1710: fix AI channels 16-31 for PCI-1713
staging: vt6656: set usb_set_intfdata on driver fail.
staging: vt6656: remove bool from vnt_radio_power_on ret
staging: vt6656: limit reg output to block size
staging: vt6656: correct return of vnt_init_registers.
staging: vt6656: Fix non zero logical return of, usb_control_msg
Pull tty/serial fixes from Greg KH:
"Here are two tty/serial driver fixes for 5.5-rc6.
The first fixes a much much reported issue with a previous tty port
link patch that is in your tree, and the second fixes a problem where
the serdev driver would claim ACPI devices that it shouldn't be
claiming.
Both have been in linux-next for a while with no reported issues"
* tag 'tty-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serdev: Don't claim unsupported ACPI serial devices
tty: always relink the port
Pull block fixes from Jens Axboe:
"A few fixes that should go into this round.
This pull request contains two NVMe fixes via Keith, removal of a dead
function, and a fix for the bio op for read truncates (Ming)"
* tag 'block-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
nvmet: fix per feat data len for get_feature
nvme: Translate more status codes to blk_status_t
fs: move guard_bio_eod() after bio_set_op_attrs
block: remove unused mp_bvec_last_segment
Pull io_uring fix from Jens Axboe:
"Single fix for this series, fixing a regression with the short read
handling.
This just removes it, as it cannot safely be done for all cases"
* tag 'io_uring-5.5-2020-01-10' of git://git.kernel.dk/linux-block:
io_uring: remove punt of short reads to async context
Pull MTD fixes from Miquel Raynal:
"MTD:
- sm_ftl: Fix NULL pointer warning.
Raw NAND:
- Cadence: fix compile testing.
- STM32: Avoid locking.
Onenand:
- Fix several sparse/build warnings.
SPI-NOR:
- Add a flag to fix interaction with Micron parts"
* tag 'mtd/fixes-for-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: Fix the writing of the Status Register on micron flashes
mtd: sm_ftl: fix NULL pointer warning
mtd: onenand: omap2: Pass correct flags for prep_dma_memcpy
mtd: onenand: samsung: Fix iomem access with regular memcpy
mtd: onenand: omap2: Fix errors in style
mtd: cadence: Fix cast to pointer from integer of different size warning
mtd: rawnand: stm32_fmc2: avoid to lock the CPU bus
Pull sound fixes from Takashi Iwai:
"A few piled ASoC fixes and usual HD-audio and USB-audio fixups. Some
of them are for ASoC core error-handling"
* tag 'sound-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: enable regmap internal locking
ALSA: hda/realtek - Add quirk for the bass speaker on Lenovo Yoga X1 7th gen
ALSA: hda/realtek - Set EAPD control to default for ALC222
ALSA: usb-audio: Apply the sample rate quirk for Bose Companion 5
ALSA: hda/realtek - Add new codec supported for ALCS1200A
ASoC: Intel: boards: Fix compile-testing RT1011/RT5682
ASoC: SOF: imx8: Fix dsp_box offset
ASoC: topology: Prevent use-after-free in snd_soc_get_pcm_runtime()
ASoC: fsl_audmix: add missed pm_runtime_disable
ASoC: stm32: spdifrx: fix input pin state management
ASoC: stm32: spdifrx: fix race condition in irq handler
ASoC: stm32: spdifrx: fix inconsistent lock state
ASoC: core: Fix access to uninitialized list heads
ASoC: soc-core: Set dpcm_playback / dpcm_capture
ASoC: SOF: imx8: fix memory allocation failure check on priv->pd_dev
ASoC: SOF: Intel: hda: hda-dai: fix oops on hda_link .hw_free
ASoC: SOF: fix fault at driver unload after failed probe
Pull thermal fix from Daniel Lezcano:
"Fix backward compatibility with old DTBs on QCOM tsens (Amit
Kucheria)"
* tag 'thermal-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
drivers: thermal: tsens: Work with old DTBs
Pull power management fixes from Rafael Wysocki:
"Prevent the cpufreq-dt driver from probing Tegra20/30 (Dmitry
Osipenko) and prevent the Intel RAPL power capping driver from
crashing during CPU initialization due to a NULL pointer dereference
if the processor model in use is not known to it (Harry Pan)"
* tag 'pm-5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: intel_rapl: add NULL pointer check to rapl_mmio_cpu_online()
cpufreq: dt-platdev: Blacklist NVIDIA Tegra20 and Tegra30 SoCs
Sven-Haegar reported looping on fib dumps when 255.255.255.255 route has
been added to a table. The looping is caused by the key rolling over from
FFFFFFFF to 0. When dumping a specific table only, we need a means to detect
when the table dump is done. The key and count saved to cb args are both 0
only at the start of the table dump. If key is 0 and count > 0, then we are
in the rollover case. Detect and return to avoid looping.
This only affects dumps of a specific table; for dumps of all tables
(the case prior to the change in the Fixes tag) inet_dump_fib moved
the entry counter to the next table and reset the cb args used by
fib_table_dump and fn_trie_dump_leaf, so the rollover ffffffff back
to 0 did not cause looping with the dumps.
Fixes: effe679266 ("net: Enable kernel side filtering of route dumps")
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Filtering fixes
Two single fixes for the L3 and L4 filtering in stmmac.
1) Updates the internal status of RSS when disabling it in order to keep
internal driver status consistent.
2) Do not lets user add a filter if RSS is enabled because the filter will
not work correctly as RSS bypasses this mechanism.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mallesham reports the TLS with async accelerator was broken by
commit d10523d0b3 ("net/tls: free the record on encryption error")
because encryption can return -EINPROGRESS in such setups, which
should not be treated as an error.
The error is also present in the BPF path (likely copied from there).
Reported-by: Mallesham Jatharakonda <mallesham.jatharakonda@oneconvergence.com>
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Fixes: d10523d0b3 ("net/tls: free the record on encryption error")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device loses sync mid way through a record - kernel
has to re-encrypt the part of the record which the device
already decrypted to be able to decrypt and authenticate
the record in its entirety.
The re-encryption piggy backs on the decryption routine,
but obviously because the partially decrypted record can't
be authenticated crypto API returns an error which is then
ignored by tls_device_reencrypt().
Commit 5c5ec66858 ("net/tls: add TlsDecryptError stat")
added a statistic to count decryption errors, this statistic
can't be incremented when we see the expected re-encryption
error. Move the inc to the caller.
Reported-and-tested-by: David Beckett <david.beckett@netronome.com>
Fixes: 5c5ec66858 ("net/tls: add TlsDecryptError stat")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to leak time wait and request sockets via the following
BPF pseudo code:
sk = bpf_skc_lookup_tcp(...)
if (sk)
bpf_sk_release(sk)
If sk->sk_state is TCP_NEW_SYN_RECV or TCP_TIME_WAIT the refcount taken
by bpf_skc_lookup_tcp is not undone by bpf_sk_release. This is because
sk_flags is re-used for other data in both kinds of sockets. The check
!sock_flag(sk, SOCK_RCU_FREE)
therefore returns a bogus result. Check that sk_flags is valid by calling
sk_fullsock. Skip checking SOCK_RCU_FREE if we already know that sk is
not a full socket.
Fixes: edbf8c01de ("bpf: add skc_lookup_tcp helper")
Fixes: f7355a6c04 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200110132336.26099-1-lmb@cloudflare.com
The existing implementation for the get_feature admin-cmd does not
use per-feature data len. This patch introduces a new helper function
nvmet_feat_data_len(), which is used to calculate per feature data len.
Right now we only set data len for fid 0x81 (NVME_FEAT_HOST_ID).
Fixes: commit e9061c3978 ("nvmet: Remove the data_len field from the nvmet_req struct")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Amit Engel <amit.engel@dell.com>
[endiness, naming, and kernel style fixes]
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Decode interrupted command and not ready namespace nvme status codes to
BLK_STS_TARGET. These are not generic IO errors and should use a non-path
specific error so that it can use the non-failover retry path.
Reported-by: John Meneghini <John.Meneghini@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e7461f ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc1d ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers. The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it. This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.
[mkp: added missing email addresses]
Fixes: 43d8eb9cfd ("[SCSI] ses: add support for enclosure component hot removal")
Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reported-by: Luo Jiaxing <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an attached disk with protection information enabled is reformatted
to Type 0 the revalidation code does not clear the original protection
type and subsequent accesses will keep setting RDPROTECT/WRPROTECT.
Set the protection type to 0 if the disk reports PROT_EN=0 in READ
CAPACITY(16).
[mkp: commit desc]
Fixes: fe542396da ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type")
Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull pstore fix from Kees Cook:
"Cengiz Can forwarded a Coverity report about more problems with a rare
pstore initialization error path, so the allocation lifetime was
rearranged to avoid needing to share the kfree() responsibilities
between caller and callee"
* tag 'pstore-v5.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: Regularize prz label allocation lifetime
Pull drm fixes from Dave Airlie:
"Pre-LCA pull request I'm not sure how things will look next week,
myself and Daniel are at LCA and I'm speaking quite late, so if I get
my talk finished I'll probably process fixes.
This week has a bunch of i915 fixes, some amdgpu fixes, one sun4i, one
core MST, and one core fb_helper fix. More details below:
core:
- mst Fix NO_STOP_BIT bit offset (Wayne)
fb_helper:
- fb_helper: Fix bits_per_pixel param set behavior to round up
(Geert)
sun4i:
- Fix RGB_DIV clock min divider on old hardware (Chen-Yu)
amdgpu:
- Stability fix for raven
- Reduce pixel encoding to if max clock is exceeded on HDMI to allow
additional high res modes
- enable DRIVER_SYNCOBJ_TIMELINE for amdgpu
i915:
- Fix GitLab issue #446 causing GPU hangs: Do not restore invalid RS
state
- Fix GitLab issue #846: Restore coarse power gating that was
disabled by initial RC66 context corruption security fixes.
- Revert f6ec948309 ("drm/i915: extend audio CDCLK>=2*BCLK
constraint to more platforms") to avoid screen flicker
- Fix to fill in unitialized uabi_instance in virtual engine uAPI
- Add two missing W/As for ICL and EHL"
* tag 'drm-fixes-2020-01-10' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: add DRIVER_SYNCOBJ_TIMELINE to amdgpu
drm/amd/display: Reduce HDMI pixel encoding if max clock is exceeded
Revert "drm/amdgpu: Set no-retry as default."
drm/fb-helper: Round up bits_per_pixel if possible
drm/sun4i: tcon: Set RGB DCLK min. divider based on hardware model
drm/i915/dp: Disable Port sync mode correctly on teardown
drm/i915: Add Wa_1407352427:icl,ehl
drm/i915: Add Wa_1408615072 and Wa_1407596294 to icl,ehl
drm/i915/gt: Restore coarse power gating
drm/i915/gt: Do not restore invalid RS state
drm/i915: Limit audio CDCLK>=2*BCLK constraint back to GLK only
drm/i915/gt: Mark up virtual engine uabi_instance
drm/dp_mst: correct the shifting in DP_REMOTE_I2C_READ
Pull rdma fixes from Jason Gunthorpe:
"First RDMA subsystem updates for 5.5-rc. A very small set of fixes,
most people seem to still be recovering from December!
Five small driver fixes:
- Fix error flow with MR allocation in bnxt_re
- An errata work around for bnxt_re
- Misuse of the workqueue API in hfi1
- Protocol error in hfi1
- Regression in 5.5 related to the mmap rework with i40iw"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
i40iw: Remove setting of VMA private data and use rdma_user_mmap_io
IB/hfi1: Adjust flow PSN with the correct resync_psn
IB/hfi1: Don't cancel unused work item
RDMA/bnxt_re: Fix Send Work Entry state check while polling completions
RDMA/bnxt_re: Avoid freeing MR resources if dereg fails
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-01-09
This series contains fixes to e1000e, igb, ixgbe, ixgbevf, i40e and iavf
drivers.
Brett fixes the validation of the virtchnl queue select bitmaps by
comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).
Radoslaw removes the limitation of only 10 filter entries for a VF and
allows use of all free RAR entries for the forwarding database, if
needed.
Cambda Zhu fixes the calculation of queue when restoring flow director
filters after resetting the adapter for ixgbe.
Manfred Rudigier fixes the SGMIISFP module discovery for 100FX/LX
modules for igb.
Stefan Assmann fixes iavf where during a VF reset event, MAC filters
were not altered, which could lead to a stale filter when an
administratively set MAC address is forced by the PF.
Adam adds the missing code to set the PHY access flag on X722 devices,
which supports accessing PHY registers with the admin queue command.
Revert a previous commit for e1000e to use "delayed work" which was
causing connections to reset unexpectedly and possible driver crashes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 2 issues in x25_connect():
1. It makes absolutely no sense to reset the neighbour and the
connection state after a (successful) nonblocking call of x25_connect.
This prevents any connection from being established, since the response
(call accept) cannot be processed.
2. Any further calls to x25_connect() while a call is pending should
simply return, instead of creating new Call Request (on different
logical channels).
This patch should also fix the "KASAN: null-ptr-deref Write in
x25_connect" and "BUG: unable to handle kernel NULL pointer dereference
in x25_connect" bugs reported by syzbot.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reported-by: syzbot+429c200ffc8772bfe070@syzkaller.appspotmail.com
Reported-by: syzbot+eec0c87f31a7c3b66f7b@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull GPIO fixes from Linus Walleij:
"Here is a host of GPIO fixes for the v5.5 series. The ACPI fix is
especially important, see summary below and in the commit for details:
- Select GPIOLIB_IRQCHIP on the max77620 GPIO expander
- Fix context restore in the Zynq driver
- Create a new ACPI quirk handler for disabling wakeups on
problematic hardware.
- Fix a coding style issue on the mockup device"
* tag 'gpio-v5.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism
gpiolib: acpi: Turn dmi_system_id table into a generic quirk table
gpio: zynq: Fix for bug in zynq_gpio_restore_context API
gpio: max77620: Add missing dependency on GPIOLIB_IRQCHIP
gpio: mockup: fix coding style
Pull pin control fixes from Linus Walleij:
"Two fixes for pin control, not much to say about it, it's just regular
driver fixes:
- Fix erroneous shift in the Meson driver
- Make Lochnagar select the GPIOLIB Kconfig symbol"
* tag 'pinctrl-v5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson: Fix wrong shift value when get drive-strength
pinctrl: lochnagar: select GPIOLIB
Pull input fixes from Dmitry Torokhov:
"Just a few small fixups here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_sc_key - only take the valid data from SCU firmware as key state
Input: add safety guards to input_set_keycode()
Input: input_event - fix struct padding on sparc64
Input: uinput - always report EPOLLOUT
Right now in tcp_bpf_recvmsg, sock read data first from sk_receive_queue
if not empty than psock->ingress_msg otherwise. If a FIN packet arrives
and there's also some data in psock->ingress_msg, the data in
psock->ingress_msg will be purged. It is always happen when request to a
HTTP1.0 server like python SimpleHTTPServer since the server send FIN
packet after data is sent out.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: Arika Chen <eaglesora@gmail.com>
Suggested-by: Arika Chen <eaglesora@gmail.com>
Signed-off-by: Lingpeng Chen <forrest0579@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200109014833.18951-1-forrest0579@gmail.com
The I2C specification states that tsu:sto for standard mode timing must
be at minimum 4us. Pictographically, this is:
SCL: ____/~~~~~~~~~
SDA: _________/~~~~
->| |<- 4us minimum
We are currently waiting 2.5us between asserting SCL and SDA, which is
in violation of the standard. Adjust the timings to ensure that we meet
what is stipulated as the minimum timings to ensure that all devices
correctly interpret the STOP bus transition.
This is more important than trying to generate a square wave with even
duty cycle.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In current driver, locks can be taken as follows:
- Register access: take a lock on regmap config and then on clock.
- Master clock provider: take a lock on clock and then on regmap config.
This can lead to the circular locking summarized below.
Remove peripheral clock management through regmap framework, and manage
peripheral clock in driver instead. On register access, lock on clock
is taken first, which allows to avoid possible locking issue.
[ 6696.561513] ======================================================
[ 6696.567670] WARNING: possible circular locking dependency detected
[ 6696.573842] 4.19.49 #866 Not tainted
[ 6696.577397] ------------------------------------------------------
[ 6696.583566] pulseaudio/6439 is trying to acquire lock:
[ 6696.588697] 87b0a25b (enable_lock){..-.}, at: clk_enable_lock+0x64/0x128
[ 6696.595377]
[ 6696.595377] but task is already holding lock:
[ 6696.601197] d858f825 (stm32_sai_sub:1342:(sai->regmap_config)->lock){....}
...
[ 6696.812513] Possible unsafe locking scenario:
[ 6696.812513]
[ 6696.818418] CPU0 CPU1
[ 6696.822935] ---- ----
[ 6696.827451] lock(stm32_sai_sub:1342:(sai->regmap_config)->lock);
[ 6696.833618] lock(enable_lock);
[ 6696.839350] lock(stm32_sai_sub:1342:
(sai->regmap_config)->lock);
[ 6696.848035] lock(enable_lock);
Fixes: 03e78a242a ("ASoC: stm32: sai: add h7 support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20200109083254.478-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
With gcc -O3, we get a new warning:
In file included from arch/arm64/include/asm/processor.h:28,
from drivers/mtd/sm_ftl.c:8:
In function 'memset',
inlined from 'sm_read_sector.constprop' at drivers/mtd/sm_ftl.c:250:3:
include/linux/string.h:411:9: error: argument 1 null where non-null expected [-Werror=nonnull]
return __builtin_memset(p, c, size);
>From all I can tell, this cannot happen (the function is called
either with a NULL buffer or with a -1 block number but not both),
but adding a check makes it more robust and avoids the warning.
Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The commit converting the driver to DMAengine was missing the flags for
the memcpy prepare call.
It went unnoticed since the omap-dma driver was ignoring them.
Fixes: 3ed6a4d1de (" mtd: onenand: omap2: Convert to use dmaengine for memcp")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use dma_addr_t type to pass memory address and control data in
DMA descriptor fields memory_pointer and ctrl_data_ptr
To fix warning: cast to pointer from integer of different size
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Pull HID fixes from Jiri Kosina:
- fix for OOB in hiddev, from Dmitry Torokhov
- _poll API fixes for hidraw, from Marcel Holtmann
- functional fix for Steam driver, from Rodrigo Rivas Costa
- a few new device IDs / device-specific quirks and other assorted
smaller fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: steam: Fix input device disappearing
HID: intel-ish-hid: ipc: Add Tiger Lake PCI device ID
drivers/hid/hid-multitouch.c: fix a possible null pointer access.
HID: wacom: Recognize new MobileStudio Pro PID
HID: intel-ish-hid: ipc: add CMP device id
HID: hiddev: fix mess in hiddev_open()
HID: hid-input: clear unmapped usages
HID: Add quirk for incorrect input length on Lenovo Y720
HID: asus: Ignore Asus vendor-page usage-code 0xff events
HID: ite: Add USB id match for Acer SW5-012 keyboard dock
HID: Add quirk for Xin-Mo Dual Controller
HID: Fix slab-out-of-bounds read in hid_field_extract
HID: multitouch: Add LG MELF0410 I2C touchscreen support
HID: uhid: Fix returning EPOLLOUT from uhid_char_poll
HID: hidraw: Fix returning EPOLLOUT from hidraw_poll
Pull networking fixes from David Miller:
1) Missing netns pointer init in arp_tables, from Florian Westphal.
2) Fix normal tcp SACK being treated as D-SACK, from Pengcheng Yang.
3) Fix divide by zero in sch_cake, from Wen Yang.
4) Len passed to skb_put_padto() is wrong in qrtr code, from Carl
Huang.
5) cmd->obj.chunk is leaked in sctp code error paths, from Xin Long.
6) cgroup bpf programs can be released out of order, fix from Roman
Gushchin.
7) Make sure stmmac debugfs entry name is changed when device name
changes, from Jiping Ma.
8) Fix memory leak in vlan_dev_set_egress_priority(), from Eric
Dumazet.
9) SKB leak in lan78xx usb driver, also from Eric Dumazet.
10) Ridiculous TCA_FQ_QUANTUM values configured can cause loops in fq
packet scheduler, reject them. From Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
tipc: fix wrong connect() return code
tipc: fix link overflow issue at socket shutdown
netfilter: ipset: avoid null deref when IPSET_ATTR_LINENO is present
netfilter: conntrack: dccp, sctp: handle null timeout argument
atm: eni: fix uninitialized variable warning
macvlan: do not assume mac_header is set in macvlan_broadcast()
net: sch_prio: When ungrafting, replace with FIFO
mlxsw: spectrum_qdisc: Ignore grafting of invisible FIFO
MAINTAINERS: Remove myself as co-maintainer for qcom-ethqos
gtp: fix bad unlock balance in gtp_encap_enable_socket
pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM
tipc: remove meaningless assignment in Makefile
tipc: do not add socket.o to tipc-y twice
net: stmmac: dwmac-sun8i: Allow all RGMII modes
net: stmmac: dwmac-sunxi: Allow all RGMII modes
net: usb: lan78xx: fix possible skb leak
net: stmmac: Fixed link does not need MDIO Bus
vlan: vlan_changelink() should propagate errors
vlan: fix memory leak in vlan_dev_set_egress_priority
stmmac: debugfs entry name is not be changed when udev rename device name.
...
The X722 FW API version 1.9 adds support for accessing PHY
registers with Admin Queue Command. This enables reading
EEPROM data from (Q)SFP+ transceivers, what was previously
possible only on X710 devices.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently MAC filters are not altered during a VF reset event. This may
lead to a stale filter when an administratively set MAC is forced by the
PF.
For an administratively set MAC the PF driver deletes the VFs filters,
overwrites the VFs MAC address and triggers a VF reset. However
the VF driver itself is not aware of the filter removal, which is what
the VF reset is for.
The VF reset queues all filters present in the VF driver to be re-added
to the PF filter list (including the filter for the now stale VF MAC
address) and triggers a VIRTCHNL_OP_GET_VF_RESOURCES event, which
provides the new MAC address to the VF.
When this happens i40e will complain and reject the stale MAC filter,
at least in the untrusted VF case.
i40e 0000:08:00.0: Setting MAC 3c:fa:fa:fa:fa:01 on VF 0
iavf 0000:08:02.0: Reset warning received from the PF
iavf 0000:08:02.0: Scheduling reset task
i40e 0000:08:00.0: Bring down and up the VF interface to make this change effective.
i40e 0000:08:00.0: VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation
i40e 0000:08:00.0: VF 0 failed opcode 10, retval: -1
iavf 0000:08:02.0: Failed to add MAC filter, error IAVF_ERR_NVM
To avoid re-adding the stale MAC filter it needs to be removed from the
VF driver's filter list before queuing the existing filters. Then during
the VIRTCHNL_OP_GET_VF_RESOURCES event the correct filter needs to be
added again, at which point the MAC address has been updated.
As a bonus this change makes bringing the VF down and up again
superfluous for the administratively set MAC case.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.
Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.
Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.
The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.
Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in i40e_vc_disable_queues_msg() we are incorrectly
validating the virtchnl queue select bitmaps. The
virtchnl_queue_select rx_queues and tx_queue bitmap is being
compared against ICE_MAX_VF_QUEUES, but the problem is that
these bitmaps can have a value greater than I40E_MAX_VF_QUEUES.
Fix this by comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).
Also, add the function i40e_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.
Suggested-by: Arkady Gilinksky <arkady.gilinsky@harmonicinc.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When CONFIG_SYSFS is disabled, but CONFIG_HOTPLUG_SMT is enabled,
the kernel fails to link:
arch/x86/power/cpu.o: In function `hibernate_resume_nonboot_cpu_disable':
(.text+0x38d): undefined reference to `cpuhp_smt_enable'
arch/x86/power/hibernate.o: In function `arch_resume_nosmt':
hibernate.c:(.text+0x291): undefined reference to `cpuhp_smt_enable'
hibernate.c:(.text+0x29c): undefined reference to `cpuhp_smt_disable'
Move the exported functions out of the #ifdef section into its
own with the correct conditions.
The patch that caused this is marked for stable backports, so
this one may need to be backported as well.
Fixes: ec527c3180 ("x86/power: Fix 'nosmt' vs hibernation triple fault during resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191210195614.786555-1-arnd@arndb.de
The new machine loader on z15 always creates an IPL Report block and
thus sets the IPL_PL_FLAG_IPLSR even when secure boot is disabled. This
causes the wrong message being printed at boot. Fix this by checking for
IPL_PL_FLAG_SIPL instead.
Fixes: 9641b8cc73 ("s390/ipl: read IPL report at early boot")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch moves the reset invocation of an ap device when
fresh detected from the ap bus to the probe() function of
the driver responsible for this device.
The virtualisation of ap devices makes it necessary to
remove unconditioned resets on fresh appearing apqn devices.
It may be that such a device is already enabled for guest
usage. So there may be a race condition between host ap bus
and guest ap bus doing the reset. This patch moves the
reset from the ap bus to the zcrypt drivers. So if there
is no zcrypt driver bound to an ap device - for example
the ap device is bound to the vfio device driver - the
ap device is untouched passed to the vfio device driver.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Regression tests showed that the CCA cipher key function which
generates an CCA cipher key with given clear key value does not work
correctly. At parsing the reply CPRB two limits are wrong calculated
resulting in rejecting the reply as invalid with s390dbf message
"_ip_cprb_helper reply with invalid or unknown key block".
Fixes: f2bbc96e7c ("s390/pkey: add CCA AES cipher key support")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615
Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.
For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.
As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Commit 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
adds bio_truncate() for handling bio EOD. However, bio_truncate()
doesn't use the passed 'op' parameter from guard_bio_eod's callers.
So bio_trunacate() may retrieve wrong 'op', and zering pages may
not be done for READ bio.
Fixes this issue by moving guard_bio_eod() after bio_set_op_attrs()
in submit_bh_wbc() so that bio_truncate() can always retrieve correct
op info.
Meantime remove the 'op' parameter from guard_bio_eod() because it isn't
used any more.
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: linux-fsdevel@vger.kernel.org
Fixes: 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Fold in kerneldoc and bio_op() change.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf6 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 3feea8805d ("ARM: dts: imx6sl-evk: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead1 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 93385546ba ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The `connected` value for wired devices was not properly initialized,
it must be set to `true` upon creation, because wired devices do not
generate connection events.
When a raw client (the Steam Client) uses the device, the input device
is destroyed. Then, when the raw client finishes, it must be recreated.
But since the `connected` variable was false this never happended.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Fixes: a8039f2dd0 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The use of __sync functions for atomic memory access is not
supported in the kernel, and can result in a link error depending
on configuration:
ERROR: "__tsan_atomic32_compare_exchange_strong" [drivers/crypto/hisilicon/sec2/hisi_sec2.ko] undefined!
ERROR: "__tsan_atomic64_fetch_add" [drivers/crypto/hisilicon/sec2/hisi_sec2.ko] undefined!
Use the kernel's own atomic interfaces instead. This way the
debugfs interface actually reads the counter atomically.
Fixes: 416d82204d ("crypto: hisilicon - add HiSilicon SEC V2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In my attempt to fix a memory leak, I introduced a double-free in the
pstore error path. Instead of trying to manage the allocation lifetime
between persistent_ram_new() and its callers, adjust the logic so
persistent_ram_new() always takes a kstrdup() copy, and leaves the
caller's allocation lifetime up to the caller. Therefore callers are
_always_ responsible for freeing their label. Before, it only needed
freeing when the prz itself failed to allocate, and not in any of the
other prz failure cases, which callers would have no visibility into,
which is the root design problem that lead to both the leak and now
double-free bugs.
Reported-by: Cengiz Can <cengiz@kernel.wtf>
Link: https://lore.kernel.org/lkml/d4ec59002ede4aaf9928c7f7526da87c@kernel.wtf
Fixes: 8df955a32a ("pstore/ram: Fix error-path memory leak in persistent_ram_new() callers")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The current 'tipc_wait_for_connect()' function does a wait-loop for the
condition 'sk->sk_state != TIPC_CONNECTING' to conclude if the socket
connecting has done. However, when the condition is met, it returns '0'
even in the case the connecting is actually failed, the socket state is
set to 'TIPC_DISCONNECTING' (e.g. when the server socket has closed..).
This results in a wrong return code for the 'connect()' call from user,
making it believe that the connection is established and go ahead with
building, sending a message, etc. but finally failed e.g. '-EPIPE'.
This commit fixes the issue by changing the wait condition to the
'tipc_sk_connected(sk)', so the function will return '0' only when the
connection is really established. Otherwise, either the socket 'sk_err'
if any or '-ETIMEDOUT'/'-EINTR' will be returned correspondingly.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is suddenly shutdown or released, it will reject all the
unreceived messages in its receive queue. This applies to a connected
socket too, whereas there is only one 'FIN' message required to be sent
back to its peer in this case.
In case there are many messages in the queue and/or some connections
with such messages are shutdown at the same time, the link layer will
easily get overflowed at the 'TIPC_SYSTEM_IMPORTANCE' backlog level
because of the message rejections. As a result, the link will be taken
down. Moreover, immediately when the link is re-established, the socket
layer can continue to reject the messages and the same issue happens...
The commit refactors the '__tipc_shutdown()' function to only send one
'FIN' in the situation mentioned above. For the connectionless case, it
is unavoidable but usually there is no rejections for such socket
messages because they are 'dest-droppable' by default.
In addition, the new code makes the other socket states clear
(e.g.'TIPC_LISTEN') and treats as a separate case to avoid misbehaving.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing netns context in arp_tables, from Florian Westphal.
2) Underflow in flowtable reference counter, from wenxu.
3) Fix incorrect ethernet destination address in flowtable offload,
from wenxu.
4) Check for status of neighbour entry, from wenxu.
5) Fix NAT port mangling, from wenxu.
6) Unbind callbacks from destroy path to cleanup hardware properly
on flowtable removal.
7) Fix missing casting statistics timestamp, add nf_flowtable_time_stamp
and use it.
8) NULL pointer exception when timeout argument is null in conntrack
dccp and sctp protocol helpers, from Florian Westphal.
9) Possible nul-dereference in ipset with IPSET_ATTR_LINENO, also from
Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The set uadt functions assume lineno is never NULL, but it is in
case of ip_set_utest().
syzkaller managed to generate a netlink message that calls this with
LINENO attr present:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104
Call Trace:
ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563
pass a dummy lineno storage, its easier than patching all set
implementations.
This seems to be a day-0 bug.
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The timeout pointer can be NULL which means we should modify the
per-nets timeout instead.
All do this, except sctp and dccp which instead give:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
net/netfilter/nf_conntrack_proto_dccp.c:682
ctnl_timeout_parse_policy+0x150/0x1d0 net/netfilter/nfnetlink_cttimeout.c:67
cttimeout_default_set+0x150/0x1c0 net/netfilter/nfnetlink_cttimeout.c:368
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
Reported-by: syzbot+46a4ad33f345d1dd346e@syzkaller.appspotmail.com
Fixes: c779e84960 ("netfilter: conntrack: remove get_timeout() indirection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With -O3, gcc has found an actual unintialized variable stored
into an mmio register in two instances:
drivers/atm/eni.c: In function 'discard':
drivers/atm/eni.c:465:13: error: 'dma[1]' is used uninitialized in this function [-Werror=uninitialized]
writel(dma[i*2+1],eni_dev->rx_dma+dma_wr*8+4);
^
drivers/atm/eni.c:465:13: error: 'dma[3]' is used uninitialized in this function [-Werror=uninitialized]
Change the code to always write zeroes instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
When ungrafting from PRIO, replace child with FIFO
When a child Qdisc is removed from one of the PRIO Qdisc's bands, it is
replaced unconditionally by a NOOP qdisc. As a result, any traffic hitting
that band gets dropped. That is incorrect--no Qdisc was explicitly added
when PRIO was created, and after removal, none should have to be added
either.
In patch #2, this problem is fixed for PRIO by first attempting to create a
default Qdisc and only falling back to noop when that fails. This pattern
of attempting to create an invisible FIFO, using NOOP only as a fallback,
is also seen in some other Qdiscs.
The only driver currently offloading PRIO (and thus presumably the only one
impacted by this) is mlxsw. Therefore patch #1 extends mlxsw to handle the
replacement by an invisible FIFO gracefully.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a child Qdisc is removed from one of the PRIO Qdisc's bands, it is
replaced unconditionally by a NOOP qdisc. As a result, any traffic hitting
that band gets dropped. That is incorrect--no Qdisc was explicitly added
when PRIO was created, and after removal, none should have to be added
either.
Fix PRIO by first attempting to create a default Qdisc and only falling
back to noop when that fails. This pattern of attempting to create an
invisible FIFO, using NOOP only as a fallback, is also seen in other
Qdiscs.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will change PRIO to replace a removed Qdisc with an
invisible FIFO, instead of NOOP. mlxsw will see this replacement due to the
graft message that is generated. But because FIFO does not issue its own
REPLACE message, when the graft operation takes place, the Qdisc that mlxsw
tracks under the indicated band is still the old one. The child
handle (0:0) therefore does not match, and mlxsw rejects the graft
operation, which leads to an extack message:
Warning: Offloading graft operation failed.
Fix by ignoring the invisible children in the PRIO graft handler. The
DESTROY message of the removed Qdisc is going to follow shortly and handle
the removal.
Fixes: 32dc5efc6c ("mlxsw: spectrum: qdiscs: prio: Handle graft command")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I am no longer with Linaro, I no longer have access to documentation
for this IP. The Linaro email will start bouncing soon.
Vinod is fully capable to maintain this driver by himself, therefore
remove myself as co-maintainer for qcom-ethqos.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Florian :
If TCA_FQ_QUANTUM is set to 0x80000000, fq_deueue()
can loop forever in :
if (f->credit <= 0) {
f->credit += q->quantum;
goto begin;
}
... because f->credit is either 0 or -2147483648.
Let's limit TCA_FQ_QUANTUM to no more than 1 << 20 :
This max value should limit risks of breaking user setups
while fixing this bug.
Fixes: afe4fd0624 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Florian Westphal <fw@strlen.de>
Reported-by: syzbot+dc9071cc5a85950bdfce@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no module named tipc_diag.
The assignment to tipc_diag-y has no effect.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASPEED device tree fixes for 5.5
Fixes for some badly applied patches that went in to 5.5. There is also
a fix for an incorrect i2c address.
* tag 'aspeed-5.5-devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
Link: https://lore.kernel.org/r/CACPK8XcjazgORXNZBU1ECMukXG4HA8D9VeDxiSPifDk_iB7_dw@mail.gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
With the new omap_prm driver added unconditionally, omap2 builds
fail when the reset controller subsystem is disabled:
drivers/soc/ti/omap_prm.o: In function `omap_prm_probe':
omap_prm.c:(.text+0x2d4): undefined reference to `devm_reset_controller_register'
Link: https://lore.kernel.org/r/20191216132132.3330811-1-arnd@arndb.de
Fixes: 3e99cb214f ("soc: ti: add initial PRM driver with reset control support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Selecting RESET_CONTROLLER is actually required, otherwise we
can get a link failure in the clock driver:
drivers/clk/davinci/psc.o: In function `__davinci_psc_register_clocks':
psc.c:(.text+0x9a0): undefined reference to `devm_reset_controller_register'
drivers/clk/davinci/psc-da850.o: In function `da850_psc0_init':
psc-da850.c:(.text+0x24): undefined reference to `reset_controller_add_lookup'
Link: https://lore.kernel.org/r/20191210195202.622734-1-arnd@arndb.de
Fixes: f962396ce2 ("ARM: davinci: support multiplatform build for ARM v5")
Cc: <stable@vger.kernel.org> # v5.4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull more tpmd fixes from Jarkko Sakkinen:
"One critical regression fix (the faulty commit got merged in rc3, but
also marked for stable)"
* tag 'tpmdd-next-20200108' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Handle negative priv->response_len in tpm_common_read()
When running xfstests on the current btrfs I get the following splat from
kmemleak:
unreferenced object 0xffff88821b2404e0 (size 32):
comm "kworker/u4:7", pid 26663, jiffies 4295283698 (age 8.776s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 10 ff fd 26 82 88 ff ff ...........&....
10 ff fd 26 82 88 ff ff 20 ff fd 26 82 88 ff ff ...&.... ..&....
backtrace:
[<00000000f94fd43f>] ulist_alloc+0x25/0x60 [btrfs]
[<00000000fd023d99>] btrfs_find_all_roots_safe+0x41/0x100 [btrfs]
[<000000008f17bd32>] btrfs_find_all_roots+0x52/0x70 [btrfs]
[<00000000b7660afb>] btrfs_qgroup_rescan_worker+0x343/0x680 [btrfs]
[<0000000058e66778>] btrfs_work_helper+0xac/0x1e0 [btrfs]
[<00000000f0188930>] process_one_work+0x1cf/0x350
[<00000000af5f2f8e>] worker_thread+0x28/0x3c0
[<00000000b55a1add>] kthread+0x109/0x120
[<00000000f88cbd17>] ret_from_fork+0x35/0x40
This corresponds to:
(gdb) l *(btrfs_find_all_roots_safe+0x41)
0x8d7e1 is in btrfs_find_all_roots_safe (fs/btrfs/backref.c:1413).
1408
1409 tmp = ulist_alloc(GFP_NOFS);
1410 if (!tmp)
1411 return -ENOMEM;
1412 *roots = ulist_alloc(GFP_NOFS);
1413 if (!*roots) {
1414 ulist_free(tmp);
1415 return -ENOMEM;
1416 }
1417
Following the lifetime of the allocated 'roots' ulist, it gets freed
again in btrfs_qgroup_account_extent().
But this does not happen if the function is called with the
'BTRFS_FS_QUOTA_ENABLED' flag cleared, then btrfs_qgroup_account_extent()
does a short leave and directly returns.
Instead of directly returning we should jump to the 'out_free' in order to
free all resources as expected.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
Currently when an error occurs when calling devm_gpiod_get_optional or
calling gpiod_to_irq it causes an uninitialized error return in variable
'error' to be returned. Fix this by ensuring the error variable is set
from da8xx_ohci->oc_gpio and oc_irq.
Thanks to Dan Carpenter for spotting the uninitialized error in the
gpiod_to_irq failure case.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200107123901.101190-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnected as USB B-device, suspend interrupt should come before
diconnect interrupt, because the DP/DM pins are shorter than the
VBUS/GND pins on the USB connectors. But we sometimes get a suspend
interrupt after disconnect interrupt. In that case we have devctl set to
99 with VBUS still valid and musb_pm_runtime_check_session() wrongly
thinks we have an active session. We have no other interrupts after
disconnect coming in this case at least with the omap2430 glue.
Let's fix the issue by checking the interrupt status again with
delayed work for the devctl 99 case. In the suspend after disconnect
case the devctl session bit has cleared by then and musb can idle.
For a typical USB B-device connect case we just continue with normal
interrupts.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The priv->response_length can hold the size of an response or an negative
error code, and the tpm_common_read() needs to handle both cases correctly.
Changed the type of response_length to signed and accounted for negative
value in tpm_common_read().
Cc: stable@vger.kernel.org
Fixes: d23d124843 ("tpm: fix invalid locking in NONBLOCKING mode")
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
btrfs_del_root_ref() will simply WARN_ON() if the ref doesn't match in
any way, and then continue to delete the reference. This shouldn't
happen, we have these values because there's more to the reference than
the original root and the sub root. If any of these checks fail, return
-ENOENT.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we have the following sequence of events
btrfs sub create A
btrfs sub create A/B
btrfs sub snap A C
mkdir C/foo
mv A/B C/foo
rm -rf *
We will end up with a transaction abort.
The reason for this is because we create a root ref for B pointing to A.
When we create a snapshot of C we still have B in our tree, but because
the root ref points to A and not C we will make it appear to be empty.
The problem happens when we move B into C. This removes the root ref
for B pointing to A and adds a ref of B pointing to C. When we rmdir C
we'll see that we have a ref to our root and remove the root ref,
despite not actually matching our reference name.
Now btrfs_del_root_ref() allowing this to work is a bug as well, however
we know that this inode does not actually point to a root ref in the
first place, so we shouldn't be calling btrfs_del_root_ref() in the
first place and instead simply look up our dir index for this item and
do the rest of the removal.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_unlink_subvol takes the name of the dentry and the root objectid
based on what kind of inode this is, either a real subvolume link or a
empty one that we inherited as a snapshot. We need to fix how we unlink
in the case for BTRFS_EMPTY_SUBVOL_DIR_OBJECTID in the future, so rework
btrfs_unlink_subvol to just take the dentry and handle getting the right
objectid given the type of inode this is. There is no functional change
here, simply pushing the work into btrfs_unlink_subvol() proper.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add quirk to ALC285_FIXUP_SPEAKER2_TO_DAC1, which is the same fixup
applied for X1 Carbon 7th gen in commit d2cd795c4e ("ALSA: hda -
fixup for the bass speaker on Lenovo Carbon X1 7th gen").
Signed-off-by: Kailang Yang <kailang@realtek.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCA9552 used for fan fault and presence information is at address
61h, not 60h.
Fixes: 2efc118ce3 ("ARM: dts: aspeed: rainier: Add i2c devices")
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: rainier: Add i2c devices", which
was already applied to the tree.
Fixes: 9c44db7096 ("ARM: dts: aspeed: rainier: Add i2c devices")
Reviewed-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Tested-by: Jim Wright <wrightj@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable FMC and SPI
devices" which was already applied as part of "ARM: dts: aspeed: Add
Tacoma machine".
Fixes: 8737481e38 ("ARM: dts: aspeed: tacoma: Enable FMC and SPI devices")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is a revert of "ARM: dts: aspeed: tacoma: Enable I2C busses", which
was already applied as part of "ARM: dts: aspeed: Add Tacoma machine".
Fixes: 606bcdde67 ("ARM: dts: aspeed: tacoma: Enable I2C busses")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The FIS nodes were placed incorrectly in the device tree.
Fixes: 0fe4e30478 ("ARM: dts: aspeed-g6: Describe FSI masters")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
When an ASoC driver with pcm_destruct component ops is freed before
the PCM object instantiation (e.g. deferring the probe), it hits an
Oops at snd_soc_pcm_component_free() that calls the pcm_destruct ops
unconditionally.
Fix it by adding a NULL-check of rtd->pcm before calling callbacks.
Fixes: c64bfc9066 ("ASoC: soc-core: add new pcm_construct/pcm_destruct")
Reported-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Ben Ho <ben.ho@mediatek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200107070956.15807-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Eric Dumazet says:
====================
vlan: rtnetlink newlink fixes
First patch fixes a potential memory leak found by syzbot
Second patch makes vlan_changelink() aware of errors
and report them to user.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both vlan_dev_change_flags() and vlan_dev_set_egress_priority()
can return an error. vlan_changelink() should not ignore them.
Fixes: 07b5b17e15 ("[VLAN]: Use rtnl_link API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2020-01-07
The following pull-request contains BPF updates for your *net* tree.
We've added 2 non-merge commits during the last 1 day(s) which contain
a total of 2 files changed, 16 insertions(+), 4 deletions(-).
The main changes are:
1) Fix a use-after-free in cgroup BPF due to auto-detachment, from Roman Gushchin.
2) Fix skb out-of-bounds access in ld_abs/ind instruction, from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently punt any short read on a regular file to async context,
but this fails if the short read is due to running into EOF. This is
especially problematic since we only do the single prep for commands
now, as we don't reset kiocb->ki_pos. This can result in a 4k read on
a 1k file returning zero, as we detect the short read and then retry
from async context. At the time of retry, the position is now 1k, and
we end up reading nothing, and hence return 0.
Instead of trying to patch around the fact that short reads can be
legitimate and won't succeed in case of retry, remove the logic to punt
a short read to async context. Simply return it.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fixes for omaps for v5.5-rc cycle
Here are few fixes for v5.5-rc cycle:
- Two corner case fixes related to ti-sysc driver clock issues
- Fixes for am57xx dts for pcie gpios
- Beagle-x15 regulator dts fix
- Fix for wkup_m3_ipc driver race
* tag 'omap-for-v5.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: wkup_m3_ipc: Fix race condition with rproc_boot
ARM: dts: beagle-x15-common: Model 5V0 regulator
ARM: dts: am571x-idk: Fix gpios property to have the correct gpio number
ARM: dts: am57xx-beagle-x15/am57xx-idk: Remove "gpios" for endpoint dt nodes
bus: ti-sysc: Fix iterating over clocks
ARM: OMAP2+: Fix ti_sysc_find_one_clockdomain to check for to_clk_hw_omap
Link: https://lore.kernel.org/r/pull-1578418121-413328@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
vm_ops is now initialized in ib_uverbs_mmap() with the recent rdma mmap
API changes. Earlier it was done in rdma_umap_priv_init() which would not
be called unless a driver called rdma_user_mmap_io() in its mmap.
i40iw does not use the rdma_user_mmap_io API but sets the vma's
vm_private_data to a driver object. This now conflicts with the vm_op
rdma_umap_close as priv pointer points to the i40iw driver object instead
of the private data setup by core when rdma_user_mmap_io is called. This
leads to a crash in rdma_umap_close with a mmap put being called when it
should not have.
Remove the redundant setting of the vma private_data in i40iw as it is not
used. Also move i40iw over to use the rdma_user_mmap_io API. This gives
the extra protection of having the mappings zapped when the context is
detsroyed.
BUG: unable to handle page fault for address: 0000000100000001
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 6 PID: 9528 Comm: rping Kdump: loaded Not tainted 5.5.0-rc4+ #117
Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./Q87M-D2H, BIOS F7 01/17/2014
RIP: 0010:rdma_user_mmap_entry_put+0xa/0x30 [ib_core]
RSP: 0018:ffffb340c04c7c38 EFLAGS: 00010202
RAX: 00000000ffffffff RBX: ffff9308e7be2a00 RCX: 000000000000cec0
RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000100000001
RBP: ffff9308dc7641f0 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: ffffffff8d4414d8 R12: ffff93075182c780
R13: 0000000000000001 R14: ffff93075182d2a8 R15: ffff9308e2ddc840
FS: 0000000000000000(0000) GS:ffff9308fdc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000100000001 CR3: 00000002e0412004 CR4: 00000000001606e0
Call Trace:
rdma_umap_close+0x40/0x90 [ib_uverbs]
remove_vma+0x43/0x80
exit_mmap+0xfd/0x1b0
mmput+0x6e/0x130
do_exit+0x290/0xcc0
? get_signal+0x152/0xc40
do_group_exit+0x46/0xc0
get_signal+0x1bd/0xc40
? prepare_to_wait_event+0x97/0x190
do_signal+0x36/0x630
? remove_wait_queue+0x60/0x60
? __audit_syscall_exit+0x1d9/0x290
? rcu_read_lock_sched_held+0x52/0x90
? kfree+0x21c/0x2e0
exit_to_usermode_loop+0x4f/0xc3
do_syscall_64+0x1ed/0x270
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fae715a81fd
Code: Bad RIP value.
RSP: 002b:00007fae6e163cb0 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
RAX: fffffffffffffe00 RBX: 00007fae6e163d30 RCX: 00007fae715a81fd
RDX: 0000000000000010 RSI: 00007fae6e163cf0 RDI: 0000000000000003
RBP: 00000000013413a0 R08: 00007fae68000000 R09: 0000000000000017
R10: 0000000000000001 R11: 0000000000000293 R12: 00007fae680008c0
R13: 00007fae6e163cf0 R14: 00007fae717c9804 R15: 00007fae6e163ed0
CR2: 0000000100000001
---[ end trace b33d58d3a06782cb ]---
RIP: 0010:rdma_user_mmap_entry_put+0xa/0x30 [ib_core]
Fixes: b86deba977 ("RDMA/core: Move core content from ib_uverbs to ib_core")
Link: https://lore.kernel.org/r/20200107162223.1745-1-shiraz.saleem@intel.com
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
For high-res (8K) or HFR (4K120) displays, using uncompressed pixel
formats like YCbCr444 would exceed the bandwidth of HDMI 2.0, so the
"interesting" modes would be disabled, leaving only low-res or low
framerate modes.
This change lowers the pixel encoding to 4:2:2 or 4:2:0 if the max TMDS
clock is exceeded. Verified that 8K30 and 4K120 are now available and
working with a Samsung Q900R over an HDMI 2.0b link from a Radeon 5700.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit c18647900e ("iommu/dma: Relax locking in
iommu_dma_prepare_msi()") introduced a compliation warning,
drivers/iommu/dma-iommu.c: In function 'iommu_dma_prepare_msi':
drivers/iommu/dma-iommu.c:1206:27: warning: variable 'cookie' set but
not used [-Wunused-but-set-variable]
struct iommu_dma_cookie *cookie;
^~~~~~
Fixes: c18647900e ("iommu/dma: Relax locking in iommu_dma_prepare_msi()")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
If the device fails to be added to the group, make sure to unlink the
reference before returning.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Fixes: 39ab9555c2 ("iommu: Add sysfs bindings for struct iommu_device")
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This adds the missing teardown step that removes the device link from
the group when the device addition fails.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Fixes: 797a8b4d76 ("iommu: Handle default domain attach failure")
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When userspace requests a video mode parameter value that is not
supported, frame buffer device drivers should round it up to a supported
value, if possible, instead of just rejecting it. This allows
applications to quickly scan for supported video modes.
Currently this rule is not followed for the number of bits per pixel,
causing e.g. "fbset -depth N" to fail, if N is smaller than the current
number of bits per pixel.
Fix this by returning an error only if bits per pixel is too large, and
setting it to the current value otherwise.
See also Documentation/fb/framebuffer.rst, Section 2 (Programmer's View
of /dev/fb*").
Fixes: 865afb1194 ("drm/fb-helper: reject any changes to the fbdev")
Cc: stable@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230132734.4538-1-geert+renesas@glider.be
In commit 0b8e7bbde5 ("drm/sun4i: tcon: Set min division of TCON0_DCLK
to 1.") it was assumed that all TCON variants support a minimum divider
of 1 if only DCLK was used.
However, the oldest generation of hardware only supports minimum divider
of 4 if only DCLK is used. If a divider of 1 was used on this old
hardware, some scrolling artifact would appear. A divider of 2 seemed
OK, but a divider of 3 had artifacts as well.
Set the minimum divider when outputing to parallel RGB based on the
hardware model, with a minimum of 4 for the oldest (A10/A10s/A13/A20)
hardware, and a minimum of 1 for the rest. A value is not set for the
TCON variants lacking channel 0.
This fixes the scrolling artifacts seen on my A13 tablet.
Fixes: 0b8e7bbde5 ("drm/sun4i: tcon: Set min division of TCON0_DCLK to 1.")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107070113.28951-1-wens@kernel.org
On some laptops enabling wakeup on the GPIO interrupts used for ACPI _AEI
event handling causes spurious wakeups.
This commit adds a new honor_wakeup option, defaulting to true (our current
behavior), which can be used to disable wakeup on troublesome hardware
to avoid these spurious wakeups.
This is a workaround for an architectural problem with s2idle under Linux
where we do not have any mechanism to immediately go back to sleep after
wakeup events, other then for embedded-controller events using the standard
ACPI EC interface, for details see:
https://lore.kernel.org/linux-acpi/61450f9b-cbc6-0c09-8b3a-aff6bf9a0b3c@redhat.com/
One series of laptops which is not able to suspend without this workaround
is the HP x2 10 Cherry Trail models, this commit adds a DMI based quirk
which makes sets honor_wakeup to false on these models.
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200105160357.97154-3-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Revert changes done in commit f6ec948309 ("drm/i915: extend audio
CDCLK>=2*BCLK constraint to more platforms"). Audio drivers
communicate with i915 over HDA bus multiple times during system
boot-up and each of these transactions result in matching
get_power/put_power calls to i915, and depending on the platform,
a modeset change causing visible flicker.
GLK is the only platform with minimum CDCLK significantly lower
than BCLK, and thus for GLK setting a higher CDCLK is mandatory.
For other platforms, minimum CDCLK is close but below 2*BCLK
(e.g. on ICL, CDCLK=176.4kHz with BCLK=96kHz). Spec-wise the constraint
should be set, but in practise no communication errors have been
reported and the downside if set is the flicker observed at boot-time.
Revert to old behaviour until better mechanism to manage
probe-time clocks is available.
The full CDCLK>=2*BCLK constraint is still enforced at pipe
enable time in intel_crtc_compute_min_cdclk().
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/913
Fixes: f6ec948309 ("drm/i915: extend audio CDCLK>=2*BCLK constraint to more platforms")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231140007.31728-1-kai.vehmanen@linux.intel.com
(cherry picked from commit 1ee48a61aa)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In a rare randconfig build I came across one configuration that does
not enable CONFIG_GPIOLIB, which is needed by lochnagar:
ERROR: "devm_gpiochip_add_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_free" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_generic_request" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
ERROR: "gpiochip_get_data" [drivers/pinctrl/cirrus/pinctrl-lochnagar.ko] undefined!
Add another 'select' like all other pinctrl drivers have.
Fixes: 0548448b71 ("pinctrl: lochnagar: Add support for the Cirrus Logic Lochnagar")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191218163701.171914-1-arnd@arndb.de
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull cpufreq driver fix for v5.5-rc6 from Viresh Kumar:
"Blacklist Tegra20/30 for probing by cpufreq-dt driver."
* 'cpufreq/arm/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: dt-platdev: Blacklist NVIDIA Tegra20 and Tegra30 SoCs
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-06
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.3
('net/mlx5: Move devlink registration before interfaces load')
For -stable v5.4
('net/mlx5e: Fix hairpin RSS table size')
('net/mlx5: DR, Init lists that are used in rule's member')
('net/mlx5e: Always print health reporter message to dmesg')
('net/mlx5: DR, No need for atomic refcount for internal SW steering resources')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- kbuild found missing define of MCOUNT_INSN_SIZE for various build
configs
- Initialize variable to zero as gcc thinks it is used undefined (it
really isn't but the code is subtle enough that this doesn't hurt)
- Convert from do_div() to div64_ull() to prevent potential divide by
zero
- Unregister a trace point on error path in sched_wakeup tracer
- Use signed offset for archs that can have stext not be first
- A simple indentation fix (whitespace error)"
* tag 'trace-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix indentation issue
kernel/trace: Fix do not unregister tracepoints when register sched_migrate_task fail
tracing: Change offset type to s32 in preempt/irq tracepoints
ftrace: Avoid potential division by zero in function profiler
tracing: Have stack tracer compile when MCOUNT_INSN_SIZE is not defined
tracing: Define MCOUNT_INSN_SIZE when not defined without direct calls
tracing: Initialize val to zero in parse_entry of inject code
Whenever adding new member of rule object we attach it to 2 lists,
These 2 lists should be initialized first.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set hairpin table size to the corret size, based on the groups that
would be created in it. Groups are laid out on the table such that a
group occupies a range of entries in the table. This implies that the
group ranges should have correspondence to the table they are laid upon.
The patch cited below made group 1's size to grow hence causing
overflow of group range laid on the table.
Fixes: a795d8db2a ("net/mlx5e: Support RSS for IP-in-IP and IPv6 tunneled packets")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
No need for an atomic refcounter for the STE and hashtables.
These are internal SW steering resources and they are always
under domain mutex.
This also fixes the following refcount error:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 9 PID: 3527 at lib/refcount.c:25 refcount_warn_saturate+0x81/0xe0
Call Trace:
dr_table_init_nic+0x10d/0x110 [mlx5_core]
mlx5dr_table_create+0xb4/0x230 [mlx5_core]
mlx5_cmd_dr_create_flow_table+0x39/0x120 [mlx5_core]
__mlx5_create_flow_table+0x221/0x5f0 [mlx5_core]
esw_create_offloads_fdb_tables+0x180/0x5a0 [mlx5_core]
...
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register devlink before interfaces are added.
This will allow interfaces to use devlink while initalizing. For example,
call mlx5_is_roce_enabled.
Fixes: aba25279c1 ("net/mlx5e: Add TX reporter support")
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case a reporter exists, error message is logged only to the devlink
tracer. The devlink tracer is a visibility utility only, which user can
choose not to monitor.
After cited patch, 3rd party monitoring tools that tracks these error
message will no longer find them in dmesg, causing a regression.
With this patch, error messages are also logged into the dmesg.
Fixes: c50de4af1d ("net/mlx5e: Generalize tx reporter's functionality")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull tpmd fixes from Jarkko Sakkinen:
"There has been a bunch of reports (e.g. [*]) reporting that when
commit 5b359c7c43 ("tpm_tis_core: Turn on the TPM before probing
IRQ's") and subsequent fixes are applied it causes boot freezes on
some machines.
Unfortunately hardware where this causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's patches were supposed to fix.
With these patches reverted nothing fatal happens, TPM is fallbacked
to be used in polling mode (which is not in the end too bad because
there are no high throughput workloads for TPM).
[*] https://bugzilla.kernel.org/show_bug.cgi?id=205935"
* tag 'tpmdd-next-20200106' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: Revert "tpm_tis_core: Turn on the TPM before probing IRQ's"
tpm: Revert "tpm_tis_core: Set TPM_CHIP_FLAG_IRQ before probing for interrupts"
tpm: Revert "tpm_tis: reserve chip for duration of tpm_tis_core_init"
Igor Russkikh says:
====================
Aquantia/Marvell atlantic bugfixes 2020/01
Here is a set of recently discovered bugfixes,
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Function entries were duplicated accidentally, removing the dups.
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial loopback configuration should be called earlier, before
starting traffic on HW blocks. Otherwise depending on race conditions
it could be kept disabled.
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last code/checkpatch cleanup did a copy paste error where code from
firmware 3 API logic was moved to firmware 1 logic.
This resulted in FW1.x users would never see the link state as active.
Fixes: 7b0c342f1f ("net: atlantic: code style cleanup")
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
cgroup bpf structures were released with
corresponding cgroup structures. It guaranteed the hierarchical order
of destruction: children were always first. It preserved attached
programs from being released before their propagated copies.
But with cgroup auto-detachment there are no such guarantees anymore:
cgroup bpf is released as soon as the cgroup is offline and there are
no live associated sockets. It means that an attached program can be
detached and released, while its propagated copy is still living
in the cgroup subtree. This will obviously lead to an use-after-free
bug.
To reproduce the issue the following script can be used:
#!/bin/bash
CGROOT=/sys/fs/cgroup
mkdir -p ${CGROOT}/A ${CGROOT}/B ${CGROOT}/A/C
sleep 1
./test_cgrp2_attach ${CGROOT}/A egress &
A_PID=$!
./test_cgrp2_attach ${CGROOT}/B egress &
B_PID=$!
echo $$ > ${CGROOT}/A/C/cgroup.procs
iperf -s &
S_PID=$!
iperf -c localhost -t 100 &
C_PID=$!
sleep 1
echo $$ > ${CGROOT}/B/cgroup.procs
echo ${S_PID} > ${CGROOT}/B/cgroup.procs
echo ${C_PID} > ${CGROOT}/B/cgroup.procs
sleep 1
rmdir ${CGROOT}/A/C
rmdir ${CGROOT}/A
sleep 1
kill -9 ${S_PID} ${C_PID} ${A_PID} ${B_PID}
On the unpatched kernel the following stacktrace can be obtained:
[ 33.619799] BUG: unable to handle page fault for address: ffffbdb4801ab002
[ 33.620677] #PF: supervisor read access in kernel mode
[ 33.621293] #PF: error_code(0x0000) - not-present page
[ 33.622754] Oops: 0000 [#1] SMP NOPTI
[ 33.623202] CPU: 0 PID: 601 Comm: iperf Not tainted 5.5.0-rc2+ #23
[ 33.625545] RIP: 0010:__cgroup_bpf_run_filter_skb+0x29f/0x3d0
[ 33.635809] Call Trace:
[ 33.636118] ? __cgroup_bpf_run_filter_skb+0x2bf/0x3d0
[ 33.636728] ? __switch_to_asm+0x40/0x70
[ 33.637196] ip_finish_output+0x68/0xa0
[ 33.637654] ip_output+0x76/0xf0
[ 33.638046] ? __ip_finish_output+0x1c0/0x1c0
[ 33.638576] __ip_queue_xmit+0x157/0x410
[ 33.639049] __tcp_transmit_skb+0x535/0xaf0
[ 33.639557] tcp_write_xmit+0x378/0x1190
[ 33.640049] ? _copy_from_iter_full+0x8d/0x260
[ 33.640592] tcp_sendmsg_locked+0x2a2/0xdc0
[ 33.641098] ? sock_has_perm+0x10/0xa0
[ 33.641574] tcp_sendmsg+0x28/0x40
[ 33.641985] sock_sendmsg+0x57/0x60
[ 33.642411] sock_write_iter+0x97/0x100
[ 33.642876] new_sync_write+0x1b6/0x1d0
[ 33.643339] vfs_write+0xb6/0x1a0
[ 33.643752] ksys_write+0xa7/0xe0
[ 33.644156] do_syscall_64+0x5b/0x1b0
[ 33.644605] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by grabbing a reference to the bpf structure of each ancestor
on the initialization of the cgroup bpf structure, and dropping the
reference at the end of releasing the cgroup bpf structure.
This will restore the hierarchical order of cgroup bpf releasing,
without adding any operations on hot paths.
Thanks to Josef Bacik for the debugging and the initial analysis of
the problem.
Fixes: 4bfc0bb2c6 ("bpf: decouple the lifetime of cgroup_bpf from cgroup itself")
Reported-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fix calling multiple tee_client_close_context in case of shm allocation
fails.
Fixes: 246880958a (“firmware: broadcom: add OP-TEE based BNXT f/w manager”)
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device.mem_start is unsigned long, it should not be cast to
int right before casting to pointer. This fixes warning (compile
testing on alpha architecture):
drivers/net/wan/sdla.c: In function ‘sdla_transmit’:
drivers/net/wan/sdla.c:711:13: warning:
cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a memleak caused by no place to free cmd->obj.chunk
for the unprocessed SCTP_CMD_REPLY. This issue occurs when failing to
process a cmd while there're still SCTP_CMD_REPLY cmds on the cmd seq
with an allocated chunk in cmd->obj.chunk.
So fix it by freeing cmd->obj.chunk for each SCTP_CMD_REPLY cmd left on
the cmd seq when any cmd returns error. While at it, also remove 'nomem'
label.
Reported-by: syzbot+107c4aff5f392bf1517f@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
Pull regulator fixes from Mark Brown:
"Three small fixes here, two the result of Axel Lin's amazing work
tracking down inconsistencies in drivers"
* tag 'regulator-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: bd70528: Remove .set_ramp_delay for bd70528_ldo_ops
regulator: axp20x: Fix axp20x_set_ramp_delay
regulator: axp20x: Fix AXP22x ELDO2 regulator enable bitmask
'chrdev_open()' calls 'cdev_get()' to obtain a reference to the
'struct cdev *' stashed in the 'i_cdev' field of the target inode
structure. If the pointer is NULL, then it is initialised lazily by
looking up the kobject in the 'cdev_map' and so the whole procedure is
protected by the 'cdev_lock' spinlock to serialise initialisation of
the shared pointer.
Unfortunately, it is possible for the initialising thread to fail *after*
installing the new pointer, for example if the subsequent '->open()' call
on the file fails. In this case, 'cdev_put()' is called, the reference
count on the kobject is dropped and, if nobody else has taken a reference,
the release function is called which finally clears 'inode->i_cdev' from
'cdev_purge()' before potentially freeing the object. The problem here
is that a racing thread can happily take the 'cdev_lock' and see the
non-NULL pointer in the inode, which can result in a refcount increment
from zero and a warning:
| ------------[ cut here ]------------
| refcount_t: addition on 0; use-after-free.
| WARNING: CPU: 2 PID: 6385 at lib/refcount.c:25 refcount_warn_saturate+0x6d/0xf0
| Modules linked in:
| CPU: 2 PID: 6385 Comm: repro Not tainted 5.5.0-rc2+ #22
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
| RIP: 0010:refcount_warn_saturate+0x6d/0xf0
| Code: 05 55 9a 15 01 01 e8 9d aa c8 ff 0f 0b c3 80 3d 45 9a 15 01 00 75 ce 48 c7 c7 00 9c 62 b3 c6 08
| RSP: 0018:ffffb524c1b9bc70 EFLAGS: 00010282
| RAX: 0000000000000000 RBX: ffff9e9da1f71390 RCX: 0000000000000000
| RDX: ffff9e9dbbd27618 RSI: ffff9e9dbbd18798 RDI: ffff9e9dbbd18798
| RBP: 0000000000000000 R08: 000000000000095f R09: 0000000000000039
| R10: 0000000000000000 R11: ffffb524c1b9bb20 R12: ffff9e9da1e8c700
| R13: ffffffffb25ee8b0 R14: 0000000000000000 R15: ffff9e9da1e8c700
| FS: 00007f3b87d26700(0000) GS:ffff9e9dbbd00000(0000) knlGS:0000000000000000
| CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
| CR2: 00007fc16909c000 CR3: 000000012df9c000 CR4: 00000000000006e0
| DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
| DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
| Call Trace:
| kobject_get+0x5c/0x60
| cdev_get+0x2b/0x60
| chrdev_open+0x55/0x220
| ? cdev_put.part.3+0x20/0x20
| do_dentry_open+0x13a/0x390
| path_openat+0x2c8/0x1470
| do_filp_open+0x93/0x100
| ? selinux_file_ioctl+0x17f/0x220
| do_sys_open+0x186/0x220
| do_syscall_64+0x48/0x150
| entry_SYSCALL_64_after_hwframe+0x44/0xa9
| RIP: 0033:0x7f3b87efcd0e
| Code: 89 54 24 08 e8 a3 f4 ff ff 8b 74 24 0c 48 8b 3c 24 41 89 c0 44 8b 54 24 08 b8 01 01 00 00 89 f4
| RSP: 002b:00007f3b87d259f0 EFLAGS: 00000293 ORIG_RAX: 0000000000000101
| RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f3b87efcd0e
| RDX: 0000000000000000 RSI: 00007f3b87d25a80 RDI: 00000000ffffff9c
| RBP: 00007f3b87d25e90 R08: 0000000000000000 R09: 0000000000000000
| R10: 0000000000000000 R11: 0000000000000293 R12: 00007ffe188f504e
| R13: 00007ffe188f504f R14: 00007f3b87d26700 R15: 0000000000000000
| ---[ end trace 24f53ca58db8180a ]---
Since 'cdev_get()' can already fail to obtain a reference, simply move
it over to use 'kobject_get_unless_zero()' instead of 'kobject_get()',
which will cause the racing thread to return -ENXIO if the initialising
thread fails unexpectedly.
Cc: Hillf Danton <hdanton@sina.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: syzbot+82defefbbd8527e1c2cb@syzkaller.appspotmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191219120203.32691-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serdev sub-system claims all ACPI serial devices that are not already
initialised. As a result, no device node is created for serial ports
on certain boards such as the Apollo Lake based UP2. This has the
unintended consequence of not being able to raise the login prompt via
serial connection.
Introduce a blacklist to reject ACPI serial devices that should not be
claimed by serdev sub-system. Add the peripheral ids for Intel HS UART
to the blacklist to bring back serial port on SoCs carrying them.
Cc: stable@vger.kernel.org
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Johan Hovold <johan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191219100345.911093-1-punit1.agrawal@toshiba.co.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull RTC fixes from Alexandre Belloni:
"A few fixes for this cycle. The CMOS AltCentury support broke a few
platforms with a recent BIOS so I reverted it. The mt6397 fix is not
that critical but good to have. And finally, the sun6i fix repairs
WiFi and BT on a few platforms.
Summary:
- cmos: revert AltCentury support on AMD/Hygon
- mt6397: fix alarm register overwrite
- sun6i: ensure clock is working on R40"
* tag 'rtc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: cmos: Revert "rtc: Fix the AltCentury value on AMD/Hygon platform"
rtc: mt6397: fix alarm register overwrite
rtc: sun6i: Add support for RTC clocks on R40
The ARMv8 64-bit architecture supports execute-only user permissions by
clearing the PTE_USER and PTE_UXN bits, practically making it a mostly
privileged mapping but from which user running at EL0 can still execute.
The downside, however, is that the kernel at EL1 inadvertently reading
such mapping would not trip over the PAN (privileged access never)
protection.
Revert the relevant bits from commit cab15ce604 ("arm64: Introduce
execute-only page access permissions") so that PROT_EXEC implies
PROT_READ (and therefore PTE_USER) until the architecture gains proper
support for execute-only user mappings.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Cc: <stable@vger.kernel.org> # 4.9.x-
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Fixes: 21df4a8b60 ("tpm_tis: reserve chip for duration of tpm_tis_core_init")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
There has been a bunch of reports (one from kernel bugzilla linked)
reporting that when this commit is applied it causes on some machines
boot freezes.
Unfortunately hardware where this commit causes a failure is not widely
available (only one I'm aware is Lenovo T490), which means we cannot
predict yet how long it will take to properly fix tpm_tis interrupt
probing.
Thus, the least worst short term action is to revert the code to the
state before this commit. In long term we need fix the tpm_tis probing
code to work on machines that Stefan's fix was supposed to fix.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205935
Fixes: 1ea32c83c6 ("tpm_tis_core: Set TPM_CHIP_FLAG_IRQ before probing for interrupts")
Cc: stable@vger.kernel.org
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Xiaoping Zhou <xiaoping.zhou@intel.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix OP-TEE multi page dynamic shm pool alloc
* tag 'tee-optee-fix-for-5.5' of git://git.linaro.org:/people/jens.wiklander/linux-tee:
optee: Fix multi page dynamic shm pool alloc
Link: https://lore.kernel.org/r/20200103103710.GA3469@jax
Signed-off-by: Olof Johansson <olof@lixom.net>
The register blocks don't occupy 4K. In fact, some blocks are packed
close to others and assuming they're 4K causes overlaps:
pxa2xx-i2c d4033800.i2c: can't request region for resource
[mem 0xd4033800-0xd40347ff]
Link: https://lore.kernel.org/r/20191220071443.247183-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Determined empirically, no documentation is available.
The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit f36797ee43 ("ARM: mmp/mmp2: dt: enable the clock")'
Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
ASoC: Fixes for v5.5
More fixes that have been collected, nothing super remarkable here - the
few core fixes are mainly error handling related as are many of the
driver fixes.
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb05 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit bebff81fb8 ("i2c: bcm2835: Model Divider in CCF") introduced
a NULL pointer dereference on driver unload. It seems that we can't fetch
the bus clock via devm_clk_get in bcm2835_i2c_remove. As an alternative
approach store a pointer to the bus clock in the private driver structure.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SAM9X60 also supports i2c-sda-hold-time-ns. Fix the documentation accordingly.
Fixes: 2034e3f4c9 ("dt-bindings: i2c: at91: add new compatible")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds nf_flowtable_time_stamp and updates the existing code to
use it.
This patch is also implicitly fixing up hardware statistic fetching via
nf_flow_offload_stats() where casting to u32 is missing. Use
nf_flow_timeout_delta() to fix this.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
The only clk init function in this driver that register a clk is
fu540_c000_clk_init(), and thus we need to unregister the clk when this
driver is removed on that platform. Other init functions, for example
macb_clk_init(), don't register clks and therefore we shouldn't
unregister the clks when this driver is removed. Convert this
registration path to devm so it gets auto-unregistered when this driver
is removed and drop the clk_unregister() calls in driver remove (and
error paths) so that we don't erroneously remove a clk from the system
that isn't registered by this driver.
Otherwise we get strange crashes with a use-after-free when the
devm_clk_get() call in macb_clk_init() calls clk_put() on a clk pointer
that has become invalid because it is freed in clk_unregister().
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Yash Shah <yash.shah@sifive.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The emails to ks.giri@samsung.com and vipul.pandya@samsung.com bounce
with 550 error code:
host mailin.samsung.com[203.254.224.12] said: 550
5.1.1 Recipient address rejected: User unknown (in reply to RCPT TO
command)"
Drop Girish K S and Vipul Pandya from sxgbe maintainers entry.
Cc: Byungho An <bh74.an@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The len used for skb_put_padto is wrong, it need to add len of hdr.
In qrtr_node_enqueue, local variable size_t len is assign with
skb->len, then skb_push(skb, sizeof(*hdr)) will add skb->len with
sizeof(*hdr), so local variable size_t len is not same with skb->len
after skb_push(skb, sizeof(*hdr)).
Then the purpose of skb_put_padto(skb, ALIGN(len, 4)) is to add add
pad to the end of the skb's data if skb->len is not aligned to 4, but
unfortunately it use len instead of skb->len, at this line, skb->len
is 32 bytes(sizeof(*hdr)) more than len, for example, len is 3 bytes,
then skb->len is 35 bytes(3 + 32), and ALIGN(len, 4) is 4 bytes, so
__skb_put_padto will do nothing after check size(35) < len(4), the
correct value should be 36(sizeof(*hdr) + ALIGN(len, 4) = 32 + 4),
then __skb_put_padto will pass check size(35) < len(36) and add 1 byte
to the end of skb's data, then logic is correct.
function of skb_push:
void *skb_push(struct sk_buff *skb, unsigned int len)
{
skb->data -= len;
skb->len += len;
if (unlikely(skb->data < skb->head))
skb_under_panic(skb, len, __builtin_return_address(0));
return skb->data;
}
function of skb_put_padto
static inline int skb_put_padto(struct sk_buff *skb, unsigned int len)
{
return __skb_put_padto(skb, len, true);
}
function of __skb_put_padto
static inline int __skb_put_padto(struct sk_buff *skb, unsigned int len,
bool free_on_error)
{
unsigned int size = skb->len;
if (unlikely(size < len)) {
len -= size;
if (__skb_pad(skb, len, free_on_error))
return -ENOMEM;
__skb_put(skb, len);
}
return 0;
}
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atomic operations that span cache lines are super-expensive on x86
(not just to the current processor, but also to other processes as all
memory operations are blocked until the operation completes). Upcoming
x86 processors have a switch to cause such operations to generate a #AC
trap. It is expected that some real time systems will enable this mode
in BIOS.
In preparation for this, it is necessary to fix code that may execute
atomic instructions with operands that cross cachelines because the #AC
trap will crash the kernel.
Since "pwol_mask" is local and never exposed to concurrency, there is
no need to set bits in pwol_mask using atomic operations.
Directly operate on the byte which contains the bit instead of using
__set_bit() to avoid any big endian concern due to type cast to
unsigned long in __set_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sdm845 devices, during boot we see the following warnings (unless we
have added 'pd_ignore_unused' to the kernel command line):
hlos1_vote_mmnoc_mmu_tbu_sf_gdsc status stuck at 'on'
hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc status stuck at 'on'
hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_tbu2_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_tbu1_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_audio_tbu_gdsc status stuck at 'on'
As the name of these GDSCs suggests, they are "votable" and in downstream
DT, they all have the property "qcom,no-status-check-on-disable", which
means that we should not poll the status bit when we disable them.
Luckily the VOTABLE flag already exists and it does exactly what we need,
so let's make use of it to make the warnings disappear.
Fixes: 06391eddb6 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lkml.kernel.org/r/20191126153437.11808-1-georgi.djakov@linaro.org
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Callback unbinding needs to be done after nf_flow_table_free(),
otherwise entries are not removed from the hardware.
Update nft_unregister_flowtable_net_hooks() to call
nf_unregister_net_hook() instead since the commit/abort paths do not
deal with the callback unbinding anymore.
Add a comment to nft_flowtable_event() to clarify that
flow_offload_netdev_event() already removes the entries before the
callback unbinding.
Fixes: 8bb69f3b29 ("netfilter: nf_tables: add flowtable offload control plane")
Fixes ff4bf2f42a ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: wenxu <wenxu@ucloud.cn>
Shift on 32-bit word to define the port number depends on the flow
direction.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Fixes: 7acd9378dc ("netfilter: nf_flow_table_offload: Correct memcpy size for flow_overload_mangle()")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It is better to get the dst_neigh with neigh->lock and check the
nud_state is VALID. If there is not neigh previous, the lookup will
Create a non NUD_VALID with 00:00:00:00:00:00 mac.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ethernet destination for original traffic takes the source ethernet address
in the reply direction. For reply traffic, this takes the source
ethernet address of the original direction.
Fixes: c29f74e0df ("netfilter: nf_flow_table: hardware offload support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The .deactivate and .activate interfaces already deal with the reference
counter. Otherwise, this results in spurious "Device is busy" errors.
Fixes: a3c90f7a23 ("netfilter: nf_tables: flow offload expression")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After commit 85a8ce62c2 ("block: add bio_truncate to fix guard_bio_eod")
this function is unused, remove it.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[Why]
According to DP spec, it should shift left 4 digits for NO_STOP_BIT
in REMOTE_I2C_READ message. Not 5 digits.
In current code, NO_STOP_BIT is always set to zero which means I2C
master is always generating a I2C stop at the end of each I2C write
transaction while handling REMOTE_I2C_READ sideband message. This issue
might have the generated I2C signal not meeting the requirement. Take
random read in I2C for instance, I2C master should generate a repeat
start to start to read data after writing the read address. This issue
will cause the I2C master to generate a stop-start rather than a
re-start which is not expected in I2C random read.
[How]
Correct the shifting value of NO_STOP_BIT for DP_REMOTE_I2C_READ case in
drm_dp_encode_sideband_req().
Changes since v1:(https://patchwork.kernel.org/patch/11312667/)
* Add more descriptions in commit and cc to stable
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200103055001.10287-1-Wayne.Lin@amd.com
When a TID RDMA ACK to RESYNC request is received, the flow PSNs for
pending TID RDMA WRITE segments will be adjusted with the next flow
generation number, based on the resync_psn value extracted from the flow
PSN of the TID RDMA ACK packet. The resync_psn value indicates the last
flow PSN for which a TID RDMA WRITE DATA packet has been received by the
responder and the requester should resend TID RDMA WRITE DATA packets,
starting from the next flow PSN.
However, if resync_psn points to the last flow PSN for a segment and the
next segment flow PSN starts with a new generation number, use of the old
resync_psn to adjust the flow PSN for the next segment will lead to
miscalculation, resulting in WARN_ON and sge rewinding errors:
WARNING: CPU: 4 PID: 146961 at /nfs/site/home/phcvs2/gitrepo/ifs-all/components/Drivers/tmp/rpmbuild/BUILD/ifs-kernel-updates-3.10.0_957.el7.x86_64/hfi1/tid_rdma.c:4764 hfi1_rc_rcv_tid_rdma_ack+0x8f6/0xa90 [hfi1]
Modules linked in: ib_ipoib(OE) hfi1(OE) rdmavt(OE) rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfsv3 nfs_acl nfs lockd grace fscache iTCO_wdt iTCO_vendor_support skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm irqbypass crc32_pclmul ghash_clmulni_intel ib_isert iscsi_target_mod target_core_mod aesni_intel lrw gf128mul glue_helper ablk_helper cryptd rpcrdma sunrpc opa_vnic ast ttm ib_iser libiscsi drm_kms_helper scsi_transport_iscsi ipmi_ssif syscopyarea sysfillrect sysimgblt fb_sys_fops drm joydev ipmi_si pcspkr sg drm_panel_orientation_quirks ipmi_devintf lpc_ich i2c_i801 ipmi_msghandler wmi rdma_ucm ib_ucm ib_uverbs acpi_cpufreq acpi_power_meter ib_umad rdma_cm ib_cm iw_cm ip_tables ext4 mbcache jbd2 sd_mod crc_t10dif crct10dif_generic crct10dif_pclmul i2c_algo_bit crct10dif_common
crc32c_intel e1000e ib_core ahci libahci ptp libata pps_core nfit libnvdimm [last unloaded: rdmavt]
CPU: 4 PID: 146961 Comm: kworker/4:0H Kdump: loaded Tainted: G W OE ------------ 3.10.0-957.el7.x86_64 #1
Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.0X.02.0117.040420182310 04/04/2018
Workqueue: hfi0_0 _hfi1_do_tid_send [hfi1]
Call Trace:
<IRQ> [<ffffffff9e361dc1>] dump_stack+0x19/0x1b
[<ffffffff9dc97648>] __warn+0xd8/0x100
[<ffffffff9dc9778d>] warn_slowpath_null+0x1d/0x20
[<ffffffffc05d28c6>] hfi1_rc_rcv_tid_rdma_ack+0x8f6/0xa90 [hfi1]
[<ffffffffc05c21cc>] hfi1_kdeth_eager_rcv+0x1dc/0x210 [hfi1]
[<ffffffffc05c23ef>] ? hfi1_kdeth_expected_rcv+0x1ef/0x210 [hfi1]
[<ffffffffc0574f15>] kdeth_process_eager+0x35/0x90 [hfi1]
[<ffffffffc0575b5a>] handle_receive_interrupt_nodma_rtail+0x17a/0x2b0 [hfi1]
[<ffffffffc056a623>] receive_context_interrupt+0x23/0x40 [hfi1]
[<ffffffff9dd4a294>] __handle_irq_event_percpu+0x44/0x1c0
[<ffffffff9dd4a442>] handle_irq_event_percpu+0x32/0x80
[<ffffffff9dd4a4cc>] handle_irq_event+0x3c/0x60
[<ffffffff9dd4d27f>] handle_edge_irq+0x7f/0x150
[<ffffffff9dc2e554>] handle_irq+0xe4/0x1a0
[<ffffffff9e3795dd>] do_IRQ+0x4d/0xf0
[<ffffffff9e36b362>] common_interrupt+0x162/0x162
<EOI> [<ffffffff9dfa0f79>] ? swiotlb_map_page+0x49/0x150
[<ffffffffc05c2ed1>] hfi1_verbs_send_dma+0x291/0xb70 [hfi1]
[<ffffffffc05c2c40>] ? hfi1_wait_kmem+0xf0/0xf0 [hfi1]
[<ffffffffc05c3f26>] hfi1_verbs_send+0x126/0x2b0 [hfi1]
[<ffffffffc05ce683>] _hfi1_do_tid_send+0x1d3/0x320 [hfi1]
[<ffffffff9dcb9d4f>] process_one_work+0x17f/0x440
[<ffffffff9dcbade6>] worker_thread+0x126/0x3c0
[<ffffffff9dcbacc0>] ? manage_workers.isra.25+0x2a0/0x2a0
[<ffffffff9dcc1c31>] kthread+0xd1/0xe0
[<ffffffff9dcc1b60>] ? insert_kthread_work+0x40/0x40
[<ffffffff9e374c1d>] ret_from_fork_nospec_begin+0x7/0x21
[<ffffffff9dcc1b60>] ? insert_kthread_work+0x40/0x40
This patch fixes the issue by adjusting the resync_psn first if the flow
generation has been advanced for a pending segment.
Fixes: 9e93e967f7 ("IB/hfi1: Add a function to receive TID RDMA ACK packet")
Link: https://lore.kernel.org/r/20191219231920.51069.37147.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In the iowait structure, two iowait_work entries were included to queue a
given object: one for normal IB operations, and the other for TID RDMA
operations. For non-TID RDMA operations, the iowait_work structure for TID
RDMA is initialized to contain a NULL function (not used). When the QP is
reset, the function iowait_cancel_work will be called to cancel any
pending work. The problem is that this function will call
cancel_work_sync() for both iowait_work entries, even though the one for
TID RDMA is not used at all. Eventually, the call cascades to
__flush_work(), wherein a WARN_ON will be triggered due to the fact that
work->func is NULL.
The WARN_ON was introduced in commit 4d43d395fe ("workqueue: Try to
catch flush_work() without INIT_WORK().")
This patch fixes the issue by making sure that a work function is present
for TID RDMA before calling cancel_work_sync in iowait_cancel_work.
Fixes: 4d43d395fe ("workqueue: Try to catch flush_work() without INIT_WORK().")
Fixes: 5da0fc9dbf ("IB/hfi1: Prepare resource waits for dual leg")
Link: https://lore.kernel.org/r/20191219211941.58387.39883.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Current code use dma_wmb() to ensure Rx/Tx descriptors are visible
to device before writing to doorbell.
However, these dma_wmb() are wrong and unnecessary. Therefore,
they should be removed.
iowrite32be() called from gve_rx_write_doorbell()/gve_tx_put_doorbell()
should guaratee that all previous writes to WB/UC memory is visible to
device before the write done by iowrite32be().
E.g. On ARM64, iowrite32be() calls __iowmb() which expands to dma_wmb()
and only then calls __raw_writel().
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel test robot reports a boot failure with qemu in 5.5-rc,
referencing commit 2203cbf2c8 ("net: sfp: move fwnode parsing into
sfp-bus layer"). This is caused by phylink_create() being passed a
NULL fwnode, causing fwnode_property_get_reference_args() to return
-EINVAL.
Don't attempt to attach to a SFP bus if we have no fwnode, which
avoids this issue.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback feature is only supported on a few drivers like broadcom,
mellanox, etc. The default veth driver has not supported it yet. To avoid
returning failed and making the runner feel confused, let's just skip
the test on drivers that not support loopback.
Fixes: ad11340994 ("selftests: Add loopback test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some adapters need a fence Work Entry to handle retransmission. Currently
the driver checks for this condition, only if the Send queue entry is
signalled. Implement the condition check, irrespective of the signalled
state of the Work queue entries
Failure to add the fence can result in access to memory that is already
marked as completed, triggering data corruption, transmission failure,
IOMMU failures, etc.
Fixes: 9152e0b722 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Link: https://lore.kernel.org/r/1574671174-5064-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
I have missed two indentation issues in commit 64e7112ee3 ("gpio:
mockup: add set_config to support pull up/down"). This commit fixes them.
Fixes: 64e7112ee3 ("gpio: mockup: add set_config to support pull up/down")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The Advantech PCI-1713 has 32 analog input channels, but an incorrect
bit-mask in the definition of the `PCI171X_MUX_CHANH(x)` and
PCI171X_MUX_CHANL(x)` macros is causing channels 16 to 31 to be aliases
of channels 0 to 15. Change the bit-mask value from 0xf to 0xff to fix
it. Note that the channel numbers will have been range checked already,
so the bit-mask isn't really needed.
Fixes: 92c65e5553 ("staging: comedi: adv_pci1710: define the mux control register bits")
Reported-by: Dmytro Fil <monkdaf@gmail.com>
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191227170054.32051-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 59608cb1de
("staging: vt6656: clean function's error path in usbpipe.c")
the usb control functions have returned errors throughout driver
with only logical variable checking.
However, usb_control_msg return the amount of bytes transferred
this means that normal operation causes errors.
Correct the return function so only return zero when transfer
is successful.
Cc: stable <stable@vger.kernel.org> # v5.3+
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/08e88842-6f78-a2e3-a7a0-139fec960b2b@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
optee_shm_register() expected pages to be passed as an array of page
pointers rather than as an array of contiguous pages. So fix that via
correctly passing pages as per expectation.
Fixes: a249dd200d ("tee: optee: Fix dynamic shm pool allocations")
Reported-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Vincent Cao <vincent.t.cao@intel.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
In order to handle direct calls along side of function graph tracer, a check
is made to see if the address being traced by the function graph tracer is a
direct call or not. To get the address used by direct callers, the return
address is subtracted by MCOUNT_INSN_SIZE.
For some archs with certain configurations, MCOUNT_INSN_SIZE is undefined
here. But these should not be using direct calls anyway. Just define
MCOUNT_INSN_SIZE to zero in this case.
Link: https://lore.kernel.org/r/202001020219.zvE3vsty%lkp@intel.com
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: ff205766db ("ftrace: Fix function_graph tracer interaction with BPF trampoline")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
dw_spi_irq() and dw_spi_transfer_one concurrent calls.
I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null,
dw->len==4, and dw->tx_end==1.
When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one
may concurrent visit dw_spi, so I think dw_spi structure lack of protection.
Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq,
store dw rx/tx instructions and other cores handle irq load dw rx/tx
instructions may out of order.
[ 1025.321302] Call trace:
...
[ 1025.321319] __crash_kexec+0x98/0x148
[ 1025.321323] panic+0x17c/0x314
[ 1025.321329] die+0x29c/0x2e8
[ 1025.321334] die_kernel_fault+0x68/0x78
[ 1025.321337] __do_kernel_fault+0x90/0xb0
[ 1025.321346] do_page_fault+0x88/0x500
[ 1025.321347] do_translation_fault+0xa8/0xb8
[ 1025.321349] do_mem_abort+0x68/0x118
[ 1025.321351] el1_da+0x20/0x8c
[ 1025.321362] dw_writer+0xc8/0xd0
[ 1025.321364] interrupt_transfer+0x60/0x110
[ 1025.321365] dw_spi_irq+0x48/0x70
...
Signed-off-by: wuxu.wu <wuxu.wu@huawei.com>
Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2020-01-02
this is a pull request of 9 patches for net/master.
The first 5 patches target all the tcan4x5x driver. The first 3 patches
of them are by Dan Murphy and Sean Nyekjaer and improve the device
initialization (power on, reset and get device out of standby before
register access). The next patch is by Dan Murphy and disables the INH
pin device-state if the GPIO is unavailable. The last patch for the
tcan4x5x driver is by Gustavo A. R. Silva and fixes an inconsistent
PTR_ERR check in the tcan4x5x_parse_config() function.
The next patch is by Oliver Hartkopp and targets the generic CAN device
infrastructure. It ensures that an initialized headroom in outgoing CAN
sk_buffs (e.g. if injected by AF_PACKET).
The last 2 patches are by Johan Hovold and fix the kvaser_usb and gs_usb
drivers by always using the current alternate setting not blindly the
first one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd2 ("VXLAN: Use IP Tunnels tunnel ENC encap API")
Fixes: 1400615d64 ("vxlan: allow setting ipv6 traffic class")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc produces a variable may be uninitialized warning for "val" in
parse_entry(). This is really a false positive, but the code is subtle
enough to just initialize val to zero and it's not a fast path to worry
about it.
Marked for stable to remove the warning in the stable trees as well.
Cc: stable@vger.kernel.org
Fixes: 6c3edaf9fd ("tracing: Introduce trace event injection")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().
If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.
Fixes: fd6dad616d ("[TCP]: Earlier SACK block verification & simplify access to them")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augmented Power Delivery Objects (A)PDO_s are used by USB-C
PD power adapters to advertize the voltages and currents
they support. There can be up to 7 PDO_s but before PPS
(programmable power supply) there were seldom more than 4
or 5. Recently Samsung released an optional PPS 45 Watt power
adapter (EP-TA485) that has 7 PDO_s. It is for the Galaxy 10+
tablet and charges it quicker than the adapter supplied at
purchase. The EP-TA485 causes an overzealous WARN_ON to soil
the log plus it miscalculates the number of bytes to read.
So this bug has been there for some time but goes
undetected for the majority of USB-C PD power adapters on
the market today that have 6 or less PDO_s. That may soon
change as more USB-C PD adapters with PPS come to market.
Tested on a EP-TA485 and an older Lenovo PN: SA10M13950
USB-C 65 Watt adapter (without PPS and has 4 PDO_s) plus
several other PD power adapters.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191230033544.1809-1-dgilbert@interlog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d3 ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config().
The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio.
This bug was detected with the help of Coccinelle.
Fixes: 2de4973569 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de4973569 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan writes:
USB-serial fixes for 5.5-rc5
Here's a couple of new modem device ids, including a new quirk for
devices that expect zero-length packets.
Due to the holidays, only the first one has been in linux-next and with
no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add ZLP support for 0x1bc7/0x9010
USB: serial: option: add Telit ME910G1 0x110a composition
Kishon writes:
phy: for 5.5-rc
*) Fix error path in cpcap-usb driver when no host driver is loaded to
avoid debug serial console from stop working
*) Fix to let USB host idle before switching to UART mode in cpcap-usb
driver in order to avoid flakey enumeration next time
*) Prevent USB line glitches from waking up modem by enabling the USB
lines (GPIO mux) after configuring the cpcap-usb PHY
*) Improve host vs docked mode detection in cpcap-usb PHY driver to keep
VBUS enabled in host mode
*) Fix to prevent cpcap-usb PHY driver from enabling the PHY twice
*) Increase PHY ready timeout in qcom-qmp PHY as it takes more than 1ms
to initialize
*) Round clock rate down to closest 1000 Hz in phy-rockchip-inno-hdmi to
prevent wrong pixel clock to be used and result in no-signal when
configuring a mode on RK3328
* tag 'phy-for-5.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
phy: cpcap-usb: Drop extra write to usb2 register
phy: cpcap-usb: Improve host vs docked mode detection
phy: cpcap-usb: Prevent USB line glitches from waking up modem
phy: mapphone-mdm6600: Fix uninitialized status value regression
phy: cpcap-usb: Fix flakey host idling and enumerating of devices
phy: qcom-qmp: Increase PHY ready timeout
phy: cpcap-usb: Fix error path when no host driver is loaded
According to the BSP source code, both the AR100 and R_APB2 clocks have
PLL_PERIPH0 as mux index 3, not 2 as it was on previous chips. The pre-
divider used for PLL_PERIPH0 should be changed to index 3 to match.
This was verified by running a rough benchmark on the AR100 with various
clock settings:
| mux | pre-divider | iterations/second | clock source |
|=====|=============|===================|==============|
| 0 | 0 | 19033 (stable) | osc24M |
| 2 | 5 | 11466 (unstable) | iosc/osc16M |
| 2 | 17 | 11422 (unstable) | iosc/osc16M |
| 3 | 5 | 85338 (stable) | pll-periph0 |
| 3 | 17 | 27167 (stable) | pll-periph0 |
The relative performance numbers all match up (with pll-periph0 running
at its default 600MHz).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Like the APB0 clock on previous chips, this is a simple single-parent
clock with an M divider. Use the equivalent helper macro instead of
writing out the whole clock description manually.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
According to the BSP source code, the APB0 clock on the H3 and H5 has a
normal M divider, not a power-of-two divider. This matches the hardware
in the A83T (as described in both the BSP source code and the manual).
Since the A83T and H3/A64 clocks are actually the same, we can merge the
definitions.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On shutdown, ehci_power_off() is called unconditionally to power off
each port, even if it was never called to power on the port.
For chipidea, this results in a call to ehci_ci_portpower() with a request
to power off ports even if the port was never powered on.
This results in the following warning from the regulator code.
WARNING: CPU: 0 PID: 182 at drivers/regulator/core.c:2596 _regulator_disable+0x1a8/0x210
unbalanced disables for usb_otg2_vbus
Modules linked in:
CPU: 0 PID: 182 Comm: init Not tainted 5.4.6 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
[<c0313658>] (unwind_backtrace) from [<c030d698>] (show_stack+0x10/0x14)
[<c030d698>] (show_stack) from [<c1133afc>] (dump_stack+0xe0/0x10c)
[<c1133afc>] (dump_stack) from [<c0349098>] (__warn+0xf4/0x10c)
[<c0349098>] (__warn) from [<c0349128>] (warn_slowpath_fmt+0x78/0xbc)
[<c0349128>] (warn_slowpath_fmt) from [<c09f36ac>] (_regulator_disable+0x1a8/0x210)
[<c09f36ac>] (_regulator_disable) from [<c09f374c>] (regulator_disable+0x38/0xe8)
[<c09f374c>] (regulator_disable) from [<c0df7bac>] (ehci_ci_portpower+0x38/0xdc)
[<c0df7bac>] (ehci_ci_portpower) from [<c0db4fa4>] (ehci_port_power+0x50/0xa4)
[<c0db4fa4>] (ehci_port_power) from [<c0db5420>] (ehci_silence_controller+0x5c/0xc4)
[<c0db5420>] (ehci_silence_controller) from [<c0db7644>] (ehci_stop+0x3c/0xcc)
[<c0db7644>] (ehci_stop) from [<c0d5bdc4>] (usb_remove_hcd+0xe0/0x19c)
[<c0d5bdc4>] (usb_remove_hcd) from [<c0df7638>] (host_stop+0x38/0xa8)
[<c0df7638>] (host_stop) from [<c0df2f34>] (ci_hdrc_remove+0x44/0xe4)
...
Keeping track of the power enable state avoids the warning and traceback.
Fixes: c8679a2fb8 ("usb: chipidea: host: add portpower override")
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191226155754.25451-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, this new driver fails to link:
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_remove':
tegra-xudc.c:(.text+0x19d4): undefined reference to `usb_role_switch_unregister'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_probe':
tegra-xudc.c:(.text+0x2a34): undefined reference to `usb_role_switch_register'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_usb_role_sw_work':
tegra-xudc.c:(.text+0x4b64): undefined reference to `usb_role_switch_get_role'
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191216131831.3228566-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the endpoint-descriptor sanity checks to detect all duplicate
endpoint addresses in a configuration.
Commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") added a check for duplicate endpoint addresses within a
single alternate setting, but did not look for duplicate addresses in
other interfaces.
The current check would also not detect all duplicate addresses when one
endpoint is as a (bi-directional) control endpoint.
This specifically avoids overwriting the endpoint entries in struct
usb_device when enabling a duplicate endpoint, something which could
potentially lead to crashes or leaks, for example, when endpoints are
later disabled.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A system that supports resource monitoring may have multiple resources
while not all of these resources are capable of monitoring. Monitoring
related state is initialized only for resources that are capable of
monitoring and correspondingly this state should subsequently only be
removed from these resources that are capable of monitoring.
domain_add_cpu() calls domain_setup_mon_state() only when r->mon_capable
is true where it will initialize d->mbm_over. However,
domain_remove_cpu() calls cancel_delayed_work(&d->mbm_over) without
checking r->mon_capable resulting in an attempt to cancel d->mbm_over on
all resources, even those that never initialized d->mbm_over because
they are not capable of monitoring. Hence, it triggers a debugobjects
warning when offlining CPUs because those timer debugobjects are never
initialized:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint: 0x0
WARNING: CPU: 143 PID: 789 at lib/debugobjects.c:484
debug_print_object
Hardware name: HP Synergy 680 Gen9/Synergy 680 Gen9 Compute Module, BIOS I40 05/23/2018
RIP: 0010:debug_print_object
Call Trace:
debug_object_assert_init
del_timer
try_to_grab_pending
cancel_delayed_work
resctrl_offline_cpu
cpuhp_invoke_callback
cpuhp_thread_fun
smpboot_thread_fn
kthread
ret_from_fork
Fixes: e33026831b ("x86/intel_rdt/mbm: Handle counter overflow")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: john.stultz@linaro.org
Cc: sboyd@kernel.org
Cc: <stable@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: tj@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191211033042.2188-1-cai@lca.pw
If TQMX86_WDT is y and WATCHDOG_CORE is m, building fails:
drivers/watchdog/tqmx86_wdt.o: In function `tqmx86_wdt_probe':
tqmx86_wdt.c:(.text+0x46e): undefined reference to `watchdog_init_timeout'
tqmx86_wdt.c:(.text+0x4e0): undefined reference to `devm_watchdog_register_device'
Select WATCHDOG_CORE to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3c21e088f ("watchdog: tqmx86: Add watchdog driver for the IO controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191206124259.25880-1-yuehaibing@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Since commit 747d88a1a8 ("watchdog: imx7ulp: Pass the wdog instance in
imx7ulp_wdt_enable()") imx7ulp_wdt_enable() accepts a watchdog_device
structure, so fix one instance that missed such conversion.
This also fixes the following sparse warning:
drivers/watchdog/imx7ulp_wdt.c:115:31: warning: incorrect type in argument 1 (different address spaces)
drivers/watchdog/imx7ulp_wdt.c:115:31: expected struct watchdog_device *wdog
drivers/watchdog/imx7ulp_wdt.c:115:31: got void [noderef] <asn:2>*base
Fixes: 747d88a1a8 ("watchdog: imx7ulp: Pass the wdog instance inimx7ulp_wdt_enable()")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191120140916.25001-1-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We get crash when the targets checkentry function tries to make
use of the network namespace pointer for arptables.
When the net pointer got added back in 2010, only ip/ip6/ebtables were
changed to initialize it, so arptables has this set to NULL.
This isn't a problem for normal arptables because no existing
arptables target has a checkentry function that makes use of par->net.
However, direct users of the setsockopt interface can provide any
target they want as long as its registered for ARP or UNPSEC protocols.
syzkaller managed to send a semi-valid arptables rule for RATEEST target
which is enough to trigger NULL deref:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109
[..]
xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019
check_target net/ipv4/netfilter/arp_tables.c:399 [inline]
find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline]
translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572
do_replace net/ipv4/netfilter/arp_tables.c:977 [inline]
do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456
Fixes: add6746124 ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The commit 7c2763c423 ("nds32: use pgtable-nopmd instead of
4level-fixup") missed the pmd_off_k() macro which caused the following
build error:
CC arch/nds32/mm/highmem.o
In file included from arch/nds32/include/asm/page.h:57,
from include/linux/mm_types_task.h:16,
from include/linux/mm_types.h:5,
from include/linux/mmzone.h:21,
from include/linux/gfp.h:6,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/fs.h:15,
from include/linux/highmem.h:5,
from arch/nds32/mm/highmem.c:5:
arch/nds32/mm/highmem.c: In function 'kmap_atomic':
arch/nds32/include/asm/pgtable.h:360:44: error: passing argument 1 of 'pmd_offset' from incompatible pointer type [-Werror=incompatible-pointer-types]
#define pgd_offset(mm, address) ((mm)->pgd + pgd_index(address))
~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
arch/nds32/include/asm/memory.h:33:29: note: in definition of macro '__phys_to_virt'
#define __phys_to_virt(x) ((x) - PHYS_OFFSET + PAGE_OFFSET)
^
arch/nds32/include/asm/pgtable.h:193:55: note: in expansion of macro '__va'
#define pmd_page_kernel(pmd) ((unsigned long) __va(pmd_val(pmd) & PAGE_MASK))
^~~~
include/asm-generic/pgtable-nop4d.h:41:24: note: in expansion of macro 'pgd_val'
#define p4d_val(x) (pgd_val((x).pgd))
^~~~~~~
include/asm-generic/pgtable-nopud.h:50:24: note: in expansion of macro 'p4d_val'
#define pud_val(x) (p4d_val((x).p4d))
^~~~~~~
include/asm-generic/pgtable-nopmd.h:49:24: note: in expansion of macro 'pud_val'
#define pmd_val(x) (pud_val((x).pud))
^~~~~~~
arch/nds32/include/asm/pgtable.h:193:60: note: in expansion of macro 'pmd_val'
#define pmd_page_kernel(pmd) ((unsigned long) __va(pmd_val(pmd) & PAGE_MASK))
^~~~~~~
arch/nds32/include/asm/pgtable.h:190:56: note: in expansion of macro 'pmd_page_kernel'
#define pte_offset_kernel(dir, address) ((pte_t *)pmd_page_kernel(*(dir)) + pte_index(address))
^~~~~~~~~~~~~~~
arch/nds32/mm/highmem.c:52:9: note: in expansion of macro 'pte_offset_kernel'
ptep = pte_offset_kernel(pmd_off_k(vaddr), vaddr);
^~~~~~~~~~~~~~~~~
arch/nds32/include/asm/pgtable.h:362:33: note: in expansion of macro 'pgd_offset'
#define pgd_offset_k(addr) pgd_offset(&init_mm, addr)
^~~~~~~~~~
arch/nds32/include/asm/pgtable.h:198:39: note: in expansion of macro 'pgd_offset_k'
#define pmd_off_k(address) pmd_offset(pgd_offset_k(address), address)
^~~~~~~~~~~~
arch/nds32/mm/highmem.c:52:27: note: in expansion of macro 'pmd_off_k'
ptep = pte_offset_kernel(pmd_off_k(vaddr), vaddr);
^~~~~~~~~
In file included from arch/nds32/include/asm/pgtable.h:7,
from include/linux/mm.h:99,
from include/linux/highmem.h:8,
from arch/nds32/mm/highmem.c:5:
include/asm-generic/pgtable-nopmd.h:44:42: note: expected 'pud_t *' {aka 'struct <anonymous> *'} but argument is of type 'pgd_t *' {aka 'long unsigned int *'}
static inline pmd_t * pmd_offset(pud_t * pud, unsigned long address)
~~~~~~~~^~~
In file included from arch/nds32/include/asm/page.h:57,
from include/linux/mm_types_task.h:16,
from include/linux/mm_types.h:5,
from include/linux/mmzone.h:21,
from include/linux/gfp.h:6,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/fs.h:15,
from include/linux/highmem.h:5,
from arch/nds32/mm/highmem.c:5:
Updating the pmd_off_k() macro to use the correct page table unfolding
fixes the issue.
Fixes: 7c2763c423 ("nds32: use pgtable-nopmd instead of 4level-fixup")
Link: https://lore.kernel.org/lkml/201912212139.yptX8CsV%25lkp@intel.com/
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The commit c296d4dc13 ("asm-generic: fix a compilation warning") changed
asm-generic/cachflush.h to use static inlines instead of macros and as a
result the nds32 build with CONFIG_CPU_CACHE_ALIASING=n fails:
CC init/main.o
In file included from arch/nds32/include/asm/cacheflush.h:43,
from include/linux/highmem.h:12,
from include/linux/pagemap.h:11,
from include/linux/blkdev.h:16,
from include/linux/blk-cgroup.h:23,
from include/linux/writeback.h:14,
from init/main.c:44:
include/asm-generic/cacheflush.h:50:20: error: static declaration of 'flush_icache_range' follows non-static declaration
static inline void flush_icache_range(unsigned long start, unsigned long end)
^~~~~~~~~~~~~~~~~~
In file included from include/linux/highmem.h:12,
from include/linux/pagemap.h:11,
from include/linux/blkdev.h:16,
from include/linux/blk-cgroup.h:23,
from include/linux/writeback.h:14,
from init/main.c:44:
arch/nds32/include/asm/cacheflush.h:11:6: note: previous declaration of 'flush_icache_range' was here
void flush_icache_range(unsigned long start, unsigned long end);
^~~~~~~~~~~~~~~~~~
Surround the inline functions in asm-generic/cacheflush.h by ifdef's so
that architectures could override them and add the required overrides to
nds32.
Fixes: c296d4dc13 ("asm-generic: fix a compilation warning")
Link: https://lore.kernel.org/lkml/201912212139.yptX8CsV%25lkp@intel.com/
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The API for PTP system timestamping (associating a SPI transaction with
the system time at which it was transferred) is flawed: it assumes that
the xfer->tx_buf pointer will always be present.
This is, of course, not always the case.
So introduce a "progress" variable that denotes how many word have been
transferred.
Fix the Freescale DSPI driver, the only user of the API so far, in the
same patch.
Fixes: b42faeee71 ("spi: Add a PTP system timestamp to the transfer structure")
Fixes: d6b71dfaee ("spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012417.1057-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The following traceback is seen if a critical clock fails to prepare.
bcm2835-clk 3f101000.cprman: plld: couldn't lock PLL
------------[ cut here ]------------
Enabling unprepared plld_per
WARNING: CPU: 1 PID: 1 at drivers/clk/clk.c:1014 clk_core_enable+0xcc/0x2c0
...
Call trace:
clk_core_enable+0xcc/0x2c0
__clk_register+0x5c4/0x788
devm_clk_hw_register+0x4c/0xb0
bcm2835_register_pll_divider+0xc0/0x150
bcm2835_clk_probe+0x134/0x1e8
platform_drv_probe+0x50/0xa0
really_probe+0xd4/0x308
driver_probe_device+0x54/0xe8
device_driver_attach+0x6c/0x78
__driver_attach+0x54/0xd8
...
Check return values from clk_core_prepare() and clk_core_enable() and
bail out if any of those functions returns an error.
Cc: Jerome Brunet <jbrunet@baylibre.com>
Fixes: 99652a469d ("clk: migrate the count of orphaned clocks at init")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20191225163429.29694-1-linux@roeck-us.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.
Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.
With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.
We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.
And let's also drop useless debug code accidentally left over while
at it.
Fixes: b9762bebc6 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit:
0d95981438 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table")
causes the drivers/efi/libstub/random.c code to get used on x86 for the first time.
But this code was not written with EFI mixed mode in mind (running a 64
bit kernel on 32 bit EFI firmware), this causes the kernel to crash during
early boot when running in mixed mode.
The problem is that in mixed mode pointers are 64 bit, but when running on
a 32 bit firmware, EFI calls which return a pointer value by reference only
fill the lower 32 bits of the passed pointer, leaving the upper 32 bits
uninitialized which leads to crashes.
This commit fixes this by initializing pointers which are passed by
reference to EFI calls to NULL before passing them, so that the upper 32
bits are initialized to 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 0d95981438 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table")
Link: https://lkml.kernel.org/r/20191224132909.102540-3-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On x86, until PAT is initialized, WC translates into UC-. Since we
calculate and store pgprot_writecombine(PAGE_KERNEL) when earlycon is
initialized, this means we actually use UC- mappings instead of WC
mappings, which makes scrolling very slow.
Instead store a boolean flag to indicate whether we want to use
writeback or write-combine mappings, and recalculate the actual pgprot_t
we need on every mapping. Once PAT is initialized, we will start using
write-combine mappings, which speeds up the scrolling considerably.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 69c1f396f2 ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation")
Link: https://lkml.kernel.org/r/20191224132909.102540-2-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the lockdep code is really running out of the stack_trace entries,
it is likely that buffer overrun can happen and the data immediately
after stack_trace[] will be corrupted.
If there is less than LOCK_TRACE_SIZE_IN_LONGS entries left before
the call to save_trace(), the max_entries computation will leave it
with a very large positive number because of its unsigned nature. The
subsequent call to stack_trace_save() will then corrupt the data after
stack_trace[]. Fix that by changing max_entries to a signed integer
and check for negative value before calling stack_trace_save().
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12593b7467 ("locking/lockdep: Reduce space occupied by stack traces")
Link: https://lkml.kernel.org/r/20191220135128.14876-1-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It has been reported by Google that rseq is not behaving properly
with respect to clone when CLONE_VM is used without CLONE_THREAD.
It keeps the prior thread's rseq TLS registered when the TLS of the
thread has moved, so the kernel can corrupt the TLS of the parent.
The approach of clearing the per task-struct rseq registration
on clone with CLONE_THREAD flag is incomplete. It does not cover
the use-case of clone with CLONE_VM set, but without CLONE_THREAD.
Here is the rationale for unregistering rseq on clone with CLONE_VM
flag set:
1) CLONE_THREAD requires CLONE_SIGHAND, which requires CLONE_VM to be
set. Therefore, just checking for CLONE_VM covers all CLONE_THREAD
uses. There is no point in checking for both CLONE_THREAD and
CLONE_VM,
2) There is the possibility of an unlikely scenario where CLONE_SETTLS
is used without CLONE_VM. In order to be an issue, it would require
that the rseq TLS is in a shared memory area.
I do not plan on adding CLONE_SETTLS to the set of clone flags which
unregister RSEQ, because it would require that we also unregister RSEQ
on set_thread_area(2) and arch_prctl(2) ARCH_SET_FS for completeness.
So rather than doing a partial solution, it appears better to let
user-space explicitly perform rseq unregistration across clone if
needed in scenarios where CLONE_VM is not set.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191211161713.4490-3-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab8170 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dsp_box is used to keep DSP initiated messages. The value of dsp_offset
is set by the DSP with the first message, so we need a way to bootstrap
it in order to get the first message.
We do this by setting the correct default dsp_box offset which on i.MX8
is not zero.
Very interesting is why it has worked until now.
On i.MX8, DSP communicates with ARM core using a shared SDRAM memory
area. Actually, there are two shared areas:
* SDRAM0 - starting at 0x92400000, size 0x800000
* SDRAM1 - starting at 0x92C00000, size 0x800000
SDRAM0 keeps the data sections, starting with .rodata. By chance
fw_ready structure was placed at the beginning of .rodata.
dsp_box_base is defined as SDRAM0 + dsp_box_offset and it is placed
at the beginning of SDRAM1 (dsp_box_offset should be 0x800000). But
because it is zero initialized by default it points to SDRAM0 where
by chance the fw_ready was placed in the SOF firmware.
Anyhow, SOF commit 7466bee378dd811b ("clk: make freq arrays constant")
fw_ready is no longer at the beginning of SDRAM0 and everything shows
how lucky we were until now.
Fix this by properly setting the default dsp_box offset.
Fixes: 202acc565a ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220170531.10423-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Changing input state in iec capture control is not safe,
as the pin state may be changed concurrently by ASoC
framework.
Remove pin state handling in iec capture control.
Note: This introduces a restriction on capture control,
when pin sleep state is defined in device tree. In this case
channel status can be captured only when an audio stream
capture is active.
Fixes: f68c2a682d ("ASoC: stm32: spdifrx: add power management")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-4-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In current spdifrx driver locks may be requested as follows:
- request lock on iec capture control, when starting synchronization.
- request lock in interrupt context, when spdifrx stop is called
from IRQ handler.
Take lock with IRQs disabled, to avoid the possible deadlock.
Lockdep report:
[ 74.278059] ================================
[ 74.282306] WARNING: inconsistent lock state
[ 74.290120] --------------------------------
...
[ 74.314373] CPU0
[ 74.314377] ----
[ 74.314381] lock(&(&spdifrx->lock)->rlock);
[ 74.314396] <Interrupt>
[ 74.314400] lock(&(&spdifrx->lock)->rlock);
Fixes: 03e4d5d56f ("ASoC: stm32: Add SPDIFRX support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-2-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The error path of soc_new_pcm_runtime() invokes soc_free_pcm_runtime()
that may cause a few problems. First off, it calls list_del() for
rtd->list that may not be initialized. Similarly,
snd_soc_pcm_component_free() traverses over the component list that
may not be initialized, either. Such access to the uninitialized list
head would lead to either a BUG_ON() or a memory corruption.
This patch fixes the access to uninitialized list heads by
initializing the list heads properly at the beginning before those
error paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204151454.21643-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When converting a normal link to a DPCM link we need
to set dpcm_playback / dpcm_capture otherwise playback/capture
streams will not be created resulting in errors like this:
[ 36.039111] sai1-wm8960-hifi: ASoC: no backend playback stream
Fixes: a655de808c ("ASoC: core: Allow topology to override machine driver FE DAI link config")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191204151333.26625-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In Exynos542x/5800 SoCs, the G3D leaf clocks are located in the G3D power
domain. This is similar to the other hardware modules and their power
domains. However there is one thing specific to G3D clocks hierarchy.
Unlike other hardware modules, the G3D clocks hierarchy doesn't have any
gate clock between the TOP part of the hierarchy and the part located in
the power domain and some SoC internal busses are sourced directly from
the TOP muxes. The consequence of this design if the fact that the TOP
part of the hierarchy has to be enabled permanently to ensure proper
operation of the SoC power related components (G3D power domain and
Exynos Power Management Unit for system suspend/resume).
This patch adds an explicit call to clk_prepare_enable() on the last MUX
in the TOP part of G3D clock hierarchy to keep it enabled permanently to
ensure that the internal busses get their clock regardless of the main
G3D clock enablement status.
This fixes following imprecise abort issue observed on Odroid XU3/XU4
after enabling Panfrost driver by commit 1a5a85c564 "ARM: dts: exynos:
Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4"):
panfrost 11800000.gpu: clock rate = 400000000
panfrost 11800000.gpu: failed to get regulator: -517
panfrost 11800000.gpu: regulator init failed -517
Power domain G3D disable failed
...
panfrost 11800000.gpu: clock rate = 400000000
8<--- cut here ---
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: : 1406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 7 PID: 53 Comm: kworker/7:1 Not tainted 5.4.0-rc8-next-20191119-00032-g56f1001191a6 #6923
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at panfrost_gpu_soft_reset+0x94/0x110
LR is at ___might_sleep+0x128/0x2dc
...
[<c05c231c>] (panfrost_gpu_soft_reset) from [<c05c2704>] (panfrost_gpu_init+0x10/0x67c)
[<c05c2704>] (panfrost_gpu_init) from [<c05c15d0>] (panfrost_device_init+0x158/0x2cc)
[<c05c15d0>] (panfrost_device_init) from [<c05c0cb0>] (panfrost_probe+0x80/0x178)
[<c05c0cb0>] (panfrost_probe) from [<c05cfaa0>] (platform_drv_probe+0x48/0x9c)
[<c05cfaa0>] (platform_drv_probe) from [<c05cd20c>] (really_probe+0x1c4/0x474)
[<c05cd20c>] (really_probe) from [<c05cd694>] (driver_probe_device+0x78/0x1bc)
[<c05cd694>] (driver_probe_device) from [<c05cb374>] (bus_for_each_drv+0x74/0xb8)
[<c05cb374>] (bus_for_each_drv) from [<c05ccfa8>] (__device_attach+0xd4/0x16c)
[<c05ccfa8>] (__device_attach) from [<c05cc110>] (bus_probe_device+0x88/0x90)
[<c05cc110>] (bus_probe_device) from [<c05cc634>] (deferred_probe_work_func+0x4c/0xd0)
[<c05cc634>] (deferred_probe_work_func) from [<c0149df0>] (process_one_work+0x300/0x864)
[<c0149df0>] (process_one_work) from [<c014a3ac>] (worker_thread+0x58/0x5a0)
[<c014a3ac>] (worker_thread) from [<c0151174>] (kthread+0x12c/0x160)
[<c0151174>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee03dfb0 to 0xee03dff8)
...
Code: e594300c e5933020 e3130c01 1a00000f (ebefff50).
---[ end trace badde2b74a65a540 ]---
In the above case, the Panfrost driver disables G3D clocks after failure
of getting the needed regulator and return with -EPROVE_DEFER code. This
causes G3D power domain disable failure and then, during second probe
an imprecise abort is triggered due to undefined power domain state.
Fixes: 45f10dabb5 ("clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path")
Fixes: c9f7567aff ("clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lkml.kernel.org/r/20191216131407.17225-1-m.szyprowski@samsung.com
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf report/top:
Arnaldo Carvalho de Melo:
- Fix popup menu for entries in main kernel maps other than the main one,
e.g. ".init.text", where a non-initialized pointer was causing segfaults.
Jin Yao:
- Fix incorrectly added dimensions when switching perf.data file to another
via the popup menu.
libtraceevent:
Hewenliang:
- Fix memory leakage in filter_event().
perf hists:
Yuya Fujita:
- Fix variable name's inconsistency in hists__for_each() macro.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The LSM9DS1 uses a high level interrupt.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Fixes: eb4ea0857c ("arm64: dts: fsl: librem5: Add a device tree for the Librem5 devkit")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to arm cpus binding doc,
"
On 32-bit ARM v7 or later systems this property is
required and matches the CPU MPIDR[23:0] register
bits.
Bits [23:0] in the reg cell must be set to
bits [23:0] in MPIDR.
All other bits in the reg cell must be set to 0.
"
In i.MX7ULP, the MPIDR[23:0] is 0xf00, not 0, so fix it.
Otherwise there will be warning:
"DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map"
Fixes: 20434dc92c ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using SDMA1 with UART1 is causing a "Timeout waiting for CH0" error.
This patch changes to ahb clock from SDMA1_ROOT to AHB which
fixes the timeout error.
Fixes: a05ea40eb3 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DCFG block uses little endian. Fix it so that register access becomes
correct.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The only correct and documented compatible string for the rv3029 is
microcrystal,rv3029. Fix it up.
Fixes: 52c7a088ba ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When a map is create to represent the main kernel area (vmlinux) with
map__new2() we allocate an extra area to store a pointer to the 'struct
maps' for the kernel maps, so that we can access that struct when
loading ELF files or kallsyms, as we will need to split it in multiple
maps, one per kernel module or ELF section (such as ".init.text").
So when map->dso->kernel is non-zero, it is expected that
map__kmap(map)->kmaps to be set to the tree of kernel maps (modules,
chunks of the main kernel, bpf progs put in place via
PERF_RECORD_KSYMBOL, the main kernel).
This was not the case when we were splitting the main kernel into chunks
for its ELF sections, which ended up making 'perf report --children'
processing a perf.data file with callchains to trip on
__map__is_kernel(), when we press ENTER to see the popup menu for main
histogram entries that starts at a symbol in the ".init.text" ELF
section, e.g.:
- 8.83% 0.00% swapper [kernel.vmlinux].init.text [k] start_kernel
start_kernel
cpu_startup_entry
do_idle
cpuidle_enter
cpuidle_enter_state
intel_idle
Fix it.
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/20191218190120.GB13282@kernel.org/
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We observed an issue that was some extra columns displayed after switching
perf data file in browser. The steps to reproduce:
1. perf record -a -e cycles,instructions -- sleep 3
2. perf report --group
3. In browser, we use hotkey 's' to switch to another perf.data
4. Now in browser, the extra columns 'Self' and 'Children' are displayed.
The issue is setup_sorting() executed again after repeat path, so dimensions
are added again.
This patch checks the last key returned from __cmd_report(). If it's
K_SWITCH_INPUT_DATA, skips the setup_sorting().
Fixes: ad0de0971b ("perf report: Enable the runtime switching of perf data file")
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20191220013722.20592-1-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Telit FN980 flashing device 0x1bc7/0x9010 requires zero packet
to be sent if out data size is is equal to the endpoint max size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
[ johan: switch operands in conditional ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
We define 'PT_user_r25' twice in asm-offsets.c
It's not a big issue as we define it to the same value, however
let's fix it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1002 if ((quirks & MT_QUIRK_IGNORE_DUPLICATES) && mt) {
1003 struct input_mt_slot *i_slot = &mt->slots[slotnum];
1004
1005 if (input_mt_is_active(i_slot) &&
1006 input_mt_is_used(mt, i_slot))
1007 return -EAGAIN;
1008 }
We previously assumed 'mt' could be null (see line 1002).
The following situation is similar, so add a judgement.
Signed-off-by: Pan Zhang <zhangpan26@huawei.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
One of the uses of the external clock outputs is to provide a stable
32768 Hz clock signal to WiFi and Bluetooth chips. On the R40, the RTC
has an internal RC oscillator that is muxed with the external crystal.
Allow setting the parent rate for the external clock outputs so that
requests for 32768 Hz get passed to the RTC's clock driver to mux in
the external crystal if it isn't already muxed correctly.
Fixes: cd030a78f7 ("clk: sunxi-ng: support R40 SoC")
Fixes: 01a7ea763f ("clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output")
Cc: <stable@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A copy-paste error was introduced when bitmasks were converted to
macros, incorrectly setting the enable bitmask for ELDO2 to the one
for ELDO1 for the AXP22x units.
Fix it by using the correct macro.
On affected boards, ELDO1 and/or ELDO2 are used to power the camera,
which is currently unsupported.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191218044720.21990-1-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If sof_machine_check() fails during driver probe, the IPC
state is not initialized and this will lead to a NULL
dereference at driver unload. Example log is as follows:
[ 1535.980630] sof-audio-pci 0000:00:1f.3: error: no matching ASoC machine driver found - aborting probe
[ 1535.980631] sof-audio-pci 0000:00:1f.3: error: failed to get machine info -19
[ 1535.980632] sof-audio-pci 0000:00:1f.3: error: sof_probe_work failed err: -19
[ 1550.798373] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 1550.798393] Call Trace:
[ 1550.798397] snd_sof_ipc_free+0x15/0x30 [snd_sof]
[ 1550.798399] snd_sof_device_remove+0x29/0xa0 [snd_sof]
[ 1550.798400] sof_pci_remove+0x10/0x30 [snd_sof_pci]
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A new PID is in use for repaired MobileStudio Pro devices. Add it to the
list of devices that need special-casing in wacom_wac_pad_event.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The open method of hiddev handler fails to bring the device out of
autosuspend state as was promised in 0361a28d3f, as it actually has 2
blocks that try to start the transport (call hid_hw_open()) with both
being guarded by the "open" counter, so the 2nd block is never executed as
the first block increments the counter so it is never at 0 when we check
it for the second block.
Additionally hiddev_open() was leaving counter incremented on errors,
causing the device to never be reopened properly if there was ever an
error.
Let's fix all of this by factoring out code that creates client structure
and powers up the device into a separate function that is being called
from usbhid_open() with the "existancelock" being held.
Fixes: 0361a28d3f ("HID: autosuspend support for USB HID")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.
To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+
Fixes: d23f3839fe ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PERST# line in the PCIE connector is driven by the host mode and not
EP mode. The gpios property here is used for driving the PERST# line.
Remove gpios property from all endpoint device tree nodes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit d878970f6c ("bus: ti-sysc: Add separate functions for handling
clocks") separated handling of optional clocks from the main clocks, but
introduced an issue where we do not necessarily allocate a slot for both
fck and ick clocks, but still assume fixed slots for enumerating over the
clocks.
Let's fix the issue by ensuring we always have slots for both fck and ick
even if we don't use ick, and don't attempt to enumerate optional clocks
if not allocated.
In the long run we might want to simplify things a bit by only allocating
space only for the optional clocks as we have only few devices with
optional clocks.
Fixes: d878970f6c ("bus: ti-sysc: Add separate functions for handling clocks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must bail out early if the clock is not hw_omap. Otherwise we will
try to access invalid address with hwclk->clkdm_name:
Unable to handle kernel paging request at virtual address ffffffff
Internal error: Oops: 27 [#1] ARM
...
(strcmp) from [<c011b348>] (clkdm_lookup+0x40/0x60)
[<c011b348>] (clkdm_lookup) from [<c011cb84>] (ti_sysc_clkdm_init+0x5c/0x64)
[<c011cb84>] (ti_sysc_clkdm_init) from [<c03680a8>] (sysc_probe+0x948/0x117c)
[<c03680a8>] (sysc_probe) from [<c03d0af4>] (platform_drv_probe+0x48/0x98)
...
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both NVIDIA Tegra20 and Tegra30 SoCs should be blacklisted because CPU
OPPs use supported_hw and thus platdev isn't suitable for these SoCs.
Currently cpufreq-dt driver produces a bit annoying warning splats
during boot because valid OPPs are not found, this will be fixed once
tegra20-cpufreq driver will be update to support cpufreq-dt. The warnings
will also happen on older stable kernels using newer device-trees, thus
this patch should be backported to stable kernels as well.
Cc: <stable@vger.kernel.org>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 4053aa65c5 ("ARM: tegra: cardhu-a04: Add CPU Operating Performance Points")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When reading key state from SCU, the response data from SCU firmware
is 4 bytes due to MU message protocol, but ONLY the first byte is the
key state, other 3 bytes could be some dirty data, so we should ONLY
take the first byte as key state to avoid reporting incorrect state.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 688f1dfb69 ("Input: keyboard - imx_sc: Add i.MX system controller key support")
Link: https://lore.kernel.org/r/1576202909-1661-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:
The time fields now match between kernel and user space, but all following
fields are in the wrong place.
Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.
Fixes: 141e5dcaa7 ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942eb ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be leaving half-mapped usages with potentially invalid
keycodes, as that may confuse hidinput_find_key() when the key is located
by index, which may end up feeding way too large keycode into the VT
keyboard handler and cause OOB write there:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
Cc: stable@vger.kernel.org
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At least on a T100HA an Asus vendor-page usage-code 0xff event is send on
every suspend and again on resume, resulting in the following warning:
asus 0003:0B05:1807.0002: Unmapped Asus vendor usagepage code 0xff
being logged twice on every suspend/resume.
This commit silences the "Unmapped Asus vendor usagepage code ..."
warning for usage-code 0xff to avoid these warnings being logged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Acer SW5-012 2-in-1 keyboard dock uses a Synaptics S91028 touchpad
which is connected to an ITE 8595 USB keyboard controller chip.
This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without the quirk, joystick shows up as single controller
for both first and second player pads/pins.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The syzbot fuzzer found a slab-out-of-bounds bug in the HID report
handler. The bug was caused by a report descriptor which included a
field with size 12 bits and count 4899, for a total size of 7349
bytes.
The usbhid driver uses at most a single-page 4-KB buffer for reports.
In the test there wasn't any problem about overflowing the buffer,
since only one byte was received from the device. Rather, the bug
occurred when the HID core tried to extract the data from the report
fields, which caused it to try reading data beyond the end of the
allocated buffer.
This patch fixes the problem by rejecting any report whose total
length exceeds the HID_MAX_BUFFER_SIZE limit (minus one byte to allow
for a possible report index). In theory a device could have a report
longer than that, but if there was such a thing we wouldn't handle it
correctly anyway.
Reported-and-tested-by: syzbot+09ef48aa58261464b621@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the R40 in the rtc-sun6i driver was split out for a
separate compatible string, only the RTC half was covered, and not the
clock half. Unfortunately this results in the whole driver not working,
as the RTC half expects the clock half to have been initialized.
Add support for the clock part as well. The clock part is like the H3,
but does not need to export the internal oscillator, nor does it have
a gateable LOSC external output.
This fixes issues with WiFi and Bluetooth not working on the BPI M2U.
Fixes: d6624cc750 ("rtc: sun6i: Add R40 compatible")
Cc: <stable@vger.kernel.org> # 5.3.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191205085054.6049-1-wens@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)
Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.
Fixes: 79795e20a1 ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
pm_genpd_init() can return an error. Propagate the error code to prevent
the driver from indicating that it successfully probed while there were
errors during pm_genpd_init().
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
of_genpd_add_provider_onecell() can return an error. Propagate the error
so the driver registration fails when of_genpd_add_provider_onecell()
did not work.
Fixes: eef3c2ba0a ("soc: amlogic: Add support for Everything-Else power domains controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.
Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
#define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
#define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
#define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
#define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)
Meson8b additionally has these three registers:
#define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
#define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
#define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)
Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).
The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.
Fixes: 4a5a27116b ("ARM: dts: meson8: add support for booting the secondary CPU cores")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch the GPIO buttons/switches to use interrupts instead of polling.
While at it, add the mic mute switch and the power button.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit 6aae3425aa ("ARC: mm: remove __ARCH_USE_5LEVEL_HACK") make ARC
paging code 5-level compliant but left behind a stale define of
__ARCH_USE_5LEVEL_HACK in arch/arc/include/asm/hugepage.h.
Remove it.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add multitouch support for LG MELF I2C touchscreen.
Apply the same workaround as LG USB touchscreen.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.
Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.
Fixes: 378b80370a ("hidraw: Return EPOLLOUT from hidraw_poll")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hws field of sun8i_v3s_hw_clks has only 74
members. However, the number specified by CLK_NUMBER
is 77 (= CLK_I2S0 + 1). This leads to runtime segmentation
fault that is not always reproducible.
This patch fixes the problem by specifying correct clock number.
Signed-off-by: Yunhao Tian <18373444@buaa.edu.cn>
[Maxime: Also remove the CLK_NUMBER definition]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64-OLinuXino uses DCDC1 (VCC-IO) for MMC1 supply. In commit 916b68cfe4
("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi") ALDO2 is set, which is
VCC-PL. Since DCDC1 is always present, the boards are working without a
problem.
This patch sets the correct regulator.
Fixes: 916b68cfe4 ("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
A64-OLinuXino-eMMC uses 1.8V for eMMC supply. This is done via a triple
jumper, which sets VCC-PL to either 1.8V or 3.3V. This setting is different
for boards with and without eMMC.
This is not a big issue for DDR52 mode, however the eMMC will not work in
HS200/HS400, since these modes explicitly requires 1.8V.
Fixes: 94f68f3a4b ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)")
Cc: stable@vger.kernel.org # v5.4
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The distributed arp table is using a DHT to store and retrieve MAC address
information for an IP address. This is done using unicast messages to
selected peers. The potential peers are looked up using the IP address and
the VID.
While the IP address is always stored in big endian byte order, this is not
the case of the VID. It can (depending on the host system) either be big
endian or little endian. The host must therefore always convert it to big
endian to ensure that all devices calculate the same peers for the same
lookup data.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2019-11-28 12:48:59 +01:00
517 changed files with 3903 additions and 3101 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
