Pull block fix from Jens Axboe:
"Just a single fix for a patch from Greg KH, which reportedly break
block debugfs locations for certain setups. Trivial enough that I
think we should include it now, rather than wait and release 5.2 with
it, since it's a regression in this series"
* tag 'for-linus-20190706' of git://git.kernel.dk/linux-block:
blk-mq: fix up placement of debugfs directory of queue files
Pull MIPS fixes from Paul Burton:
"A few more MIPS fixes:
- Fix a silly typo in virt_addr_valid which led to completely bogus
behavior (that happened to stop tripping up hardened usercopy
despite being broken).
- Fix UART parity setup on AR933x systems.
- A build fix for non-Linux build machines.
- Have the 'all' make target build DTBs, primarily to fit in with the
behavior of scripts/package/builddeb.
- Handle an execution hazard in TLB exceptions that use KScratch
registers, which could inadvertently clobber the $1 register on
some generally higher-end out-of-order CPUs.
- A MAINTAINERS update to fix the path to the NAND driver for Ingenic
systems"
* tag 'mips_fixes_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Correct path to moved files
MIPS: Add missing EHB in mtc0 -> mfc0 sequence.
MIPS: have "plain" make calls build dtbs for selected platforms
MIPS: fix build on non-linux hosts
MIPS: ath79: fix ar933x uart parity mode
MIPS: Fix bounds check virt_addr_valid
Pull SCSI fixes from James Bottomley:
"Two iscsi fixes.
One for an oops in the client which can be triggered by the server
authentication protocol and the other in the target code which causes
data corruption"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: set auth_protocol back to NULL if CHAP_A value is not supported
scsi: target/iblock: Fix overrun in WRITE SAME emulation
Pull vfs fixlet from Al Viro:
"Fix bogus default y in Kconfig (VALIDATE_FS_PARSER)
That thing should not be turned on by default, especially since it's
not quiet in case it finds no problems. Geert has sent the obvious fix
quite a few times, but it fell through the cracks"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: VALIDATE_FS_PARSER should default to n
When the blk-mq debugfs file creation logic was "cleaned up" it was
cleaned up too much, causing the queue file to not be created in the
correct location. Turns out the check for the directory being present
is needed as if that has not happened yet, the files should not be
created, and the function will be called later on in the initialization
code so that the files can be created in the correct location.
Fixes: 6cfc0081b0 ("blk-mq: no need to check return value of debugfs_create functions")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-block@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull kvm fixes from Paolo Bonzini:
"x86 bugfix patches and one compilation fix for ARM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm64/sve: Fix vq_present() macro to yield a bool
KVM: LAPIC: Fix pending interrupt in IRR blocked by software disable LAPIC
KVM: nVMX: Change KVM_STATE_NESTED_EVMCS to signal vmcs12 is copied from eVMCS
KVM: nVMX: Allow restore nested-state to enable eVMCS when vCPU in SMM
KVM: x86: degrade WARN to pr_warn_ratelimited
Pull mtf fixes from Miquel Raynal:
- Fix the memory organization structure of a Macronix SPI-NAND chip.
- Fix a build dependency wrongly described.
- Fix the sunxi NAND driver for A23/A33 SoCs by (a) reverting the
faulty commit introducing broken DMA support and (b) applying another
commit bringing working DMA support.
* tag 'mtd/fixes-for-5.2-final' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: sunxi: Add A23/A33 DMA support with extra MBUS configuration
Revert "mtd: rawnand: sunxi: Add A23/A33 DMA support"
mtd: rawnand: ingenic: Fix ingenic_ecc dependency
mtd: spinand: Fix max_bad_eraseblocks_per_lun info in memorg
Pull i2c fixlet from Wolfram Sang:
"I2C has a MAINTAINERS update which will be benfitial for developers,
so let's add it right away"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Add Dmitry as a reviewer
Pull nfsd fixes from Bruce Fields:
"Two more quick bugfixes for nfsd: fixing a regression causing mount
failures on high-memory machines and fixing the DRC over RDMA"
* tag 'nfsd-5.2-2' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix overflow causing non-working mounts on 1 TB machines
svcrdma: Ignore source port when computing DRC hash
Allwinner NAND controllers can make use of DMA to enhance the I/O
throughput thanks to ECC pipelining. DMA handling with A23/A33 NAND IP
is a bit different than with the older SoCs, hence the introduction of
a new compatible to handle:
* the differences between register offsets,
* the burst length change from 4 to minimum 8,
* manage SRAM accesses through MBUS with extra configuration.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This reverts commit c49836f05a.
The commit is wrong and its approach actually does not work. Let's
revert it in order to add the feature with a clean patch.
Fixes: c49836f05a ("mtd: rawnand: sunxi: Add A23/A33 DMA support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
I'm contributing to Tegra's upstream development in general and happened
to review the Tegra's I2C patches for awhile because I'm actively using
upstream kernel on all of my Tegra-powered devices and initially some of
the submitted patches were getting my attention since they were causing
problems. Recently Wolfram Sang asked whether I'm interested in becoming
a reviewer for the driver and I don't mind at all.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[wsa: ack was expressed by Thierry Reding in a mail thread]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CONFIG_VALIDATE_FS_PARSER is a debugging tool to check that the parser
tables are vaguely sane. It was set to default to 'Y' for the moment to
catch errors in upcoming fs conversion development.
Make sure it is not enabled by default in the final release of v5.1.
Fixes: 31d921c7fb ("vfs: Add configuration parser helpers")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The original implementation of vq_present() relied on aggressive
inlining in order for the compiler to know that the code is
correct, due to some const-casting issues. This was causing sparse
and clang to complain, while GCC compiled cleanly.
Commit 0c529ff789 addressed this problem, but since vq_present()
is no longer a function, there is now no implicit casting of the
returned value to the return type (bool).
In set_sve_vls(), this uncast bit value is compared against a bool,
and so may spuriously compare as unequal when both are nonzero. As
a result, KVM may reject valid SVE vector length configurations as
invalid, and vice versa.
Fix it by forcing the returned value to a bool.
Signed-off-by: Zhang Lei <zhang.lei@jp.fujitsu.com>
Fixes: 0c529ff789 ("KVM: arm64: Implement vq_present() as a macro")
Signed-off-by: Dave Martin <Dave.Martin@arm.com> [commit message rewrite]
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If probe() fails anywhere beyond the point where
sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the
firmware callback to run when firmware becomes available,
using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the
sdma instance structure
3. firmware becomes available, firmware callback is
called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain
that probe() will succeed. This guarantees that the firmware
callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the
firmware loader will increment the driver module's use count,
ensuring that the module cannot be unloaded while the
firmware callback is pending or running.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: fixed braces for if condition]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "pending" variable was a u32 but we cast it to an unsigned long
pointer when we do the for_each_set_bit() loop. The problem is that on
big endian 64bit systems that results in an out of bounds read.
Fixes: 4e4106f5e9 ("dmaengine: jz4780: Fix transfers being ACKed too soon")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull drm fixes from Dave Airlie:
"I skipped last week because there wasn't much worth doing, this week
got a few more fixes in.
amdgpu:
- default register value change
- runpm regression fix
- fan control fix
i915:
- fix Ironlake regression
panfrost:
- fix a double free
virtio:
- fix a locking bug
imx:
- crtc disable fixes"
* tag 'drm-fixes-2019-07-05-1' of git://anongit.freedesktop.org/drm/drm:
drm/imx: only send event on crtc disable if kept disabled
drm/imx: notify drm core before sending event during crtc disable
drm/i915/ringbuffer: EMIT_INVALIDATE *before* switch context
drm/amdgpu/gfx9: use reset default for PA_SC_FIFO_SIZE
drm/amdgpu: Don't skip display settings in hwmgr_resume()
drm/amd/powerplay: use hardware fan control if no powerplay fan table
drm/panfrost: Fix a double-free error
drm/etnaviv: add missing failure path to destroy suballoc
drm/virtio: move drm_connector_update_edid_property() call
drm/imx: fix stale vblank timestamp after a modeset
This series fixes stale vblank timestamps in the first event sent after
a crtc was disabled. The core now is notified via drm_crtc_vblank_off
before sending the last pending event in atomic_disable. If the crtc is
reenabled right away during to a modeset, the event is not sent at all,
as the next vblank will take care of it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1562237119.6641.16.camel@pengutronix.de
Pull crypto fixes from Herbert Xu:
"This fixes two memory leaks and a list corruption bug"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - prevent operating on larval algorithms
crypto: cryptd - Fix skcipher instance memory leak
lib/mpi: Fix karactx leak in mpi_powm
Pull ARM SoC fixes from Olof Johansson:
"Likely our final small batch of fixes for 5.2:
- Some fixes for USB on davinci, regressions were due to the recent
conversion of the OCHI driver to use GPIO regulators
- A fixup of kconfig dependencies for a TI irq controller
- A switch of armada-38x to avoid dropped characters on uart, caused
by switch of base inherited platform description earlier this year"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
soc: ti: fix irq-ti-sci link error
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Pull dax fix from Dan Williams:
"A single dax fix that has been soaking awaiting other fixes under
discussion to join it. As it is getting late in the cycle lets proceed
with this fix and save follow-on changes for post-v5.3-rc1.
- Fix xarray entry association for mixed mappings"
* tag 'dax-fix-5.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Fix xarray entry association for mixed mappings
In production we have noticed hard lockups on large machines running
large jobs due to kswaps hoarding lru lock within isolate_lru_pages when
sc->reclaim_idx is 0 which is a small zone. The lru was couple hundred
GiBs and the condition (page_zonenum(page) > sc->reclaim_idx) in
isolate_lru_pages() was basically skipping GiBs of pages while holding
the LRU spinlock with interrupt disabled.
On further inspection, it seems like there are two issues:
(1) If kswapd on the return from balance_pgdat() could not sleep (i.e.
node is still unbalanced), the classzone_idx is unintentionally set
to 0 and the whole reclaim cycle of kswapd will try to reclaim only
the lowest and smallest zone while traversing the whole memory.
(2) Fundamentally isolate_lru_pages() is really bad when the
allocation has woken kswapd for a smaller zone on a very large machine
running very large jobs. It can hoard the LRU spinlock while skipping
over 100s of GiBs of pages.
This patch only fixes (1). (2) needs a more fundamental solution. To
fix (1), in the kswapd context, if pgdat->kswapd_classzone_idx is
invalid use the classzone_idx of the previous kswapd loop otherwise use
the one the waker has requested.
Link: http://lkml.kernel.org/r/20190701201847.251028-1-shakeelb@google.com
Fixes: e716f2eb24 ("mm, vmscan: prevent kswapd sleeping prematurely due to mismatched classzone_idx")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Yang Shi <yang.shi@linux.alibaba.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0e56acae4b ("mm: initialize MAX_ORDER_NR_PAGES at a time
instead of doing larger sections") is causing a regression on some
systems when the kernel is booted as Xen dom0.
The system will just hang in early boot.
Reason is an endless loop in get_page_from_freelist() in case the first
zone looked at has no free memory. deferred_grow_zone() is always
returning true due to the following code snipplet:
/* If the zone is empty somebody else may have cleared out the zone */
if (!deferred_init_mem_pfn_range_in_zone(&i, zone, &spfn, &epfn,
first_deferred_pfn)) {
pgdat->first_deferred_pfn = ULONG_MAX;
pgdat_resize_unlock(pgdat, &flags);
return true;
}
This in turn results in the loop as get_page_from_freelist() is assuming
forward progress can be made by doing some more struct page
initialization.
Link: http://lkml.kernel.org/r/20190620160821.4210-1-jgross@suse.com
Fixes: 0e56acae4b ("mm: initialize MAX_ORDER_NR_PAGES at a time instead of doing larger sections")
Signed-off-by: Juergen Gross <jgross@suse.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes for:
- A race with ASoC HD-audio registration
- LINE6 usb-audio memory overwrite by malformed descriptor
- FireWire MIDI handling
- Missing cast for bit shifts in a few USB-audio quirks
- The wrong function calls in minor OSS sequencer code paths
- A couple of HD-audio quirks"
* tag 'sound-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: Fix write on zero-sized buffer
ALSA: hda: Fix widget_mutex incomplete protection
ALSA: firewire-lib/fireworks: fix miss detection of received MIDI messages
ALSA: seq: fix incorrect order of dest_client/dest_ports arguments
ALSA: hda/realtek - Change front mic location for Lenovo M710q
ALSA: usb-audio: fix sign unintended sign extension on left shifts
ALSA: hda/realtek: Add quirks for several Clevo notebook barebones
Fix two issues:
When called for PTRACE_TRACEME, ptrace_link() would obtain an RCU
reference to the parent's objective credentials, then give that pointer
to get_cred(). However, the object lifetime rules for things like
struct cred do not permit unconditionally turning an RCU reference into
a stable reference.
PTRACE_TRACEME records the parent's credentials as if the parent was
acting as the subject, but that's not the case. If a malicious
unprivileged child uses PTRACE_TRACEME and the parent is privileged, and
at a later point, the parent process becomes attacker-controlled
(because it drops privileges and calls execve()), the attacker ends up
with control over two processes with a privileged ptrace relationship,
which can be abused to ptrace a suid binary and obtain root privileges.
Fix both of these by always recording the credentials of the process
that is requesting the creation of the ptrace relationship:
current_cred() can't change under us, and current is the proper subject
for access control.
This change is theoretically userspace-visible, but I am not aware of
any code that it will actually break.
Fixes: 64b875f7ac ("ptrace: Capture the ptracer's creds not PT_PTRACE_CAP")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The event will be sent as part of the vblank enable during the modeset
if the crtc is not being kept disabled.
Fixes: 5f2f911578 ("drm/imx: atomic phase 3 step 1: Use atomic configuration")
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Notify drm core before sending pending events during crtc disable.
This fixes the first event after disable having an old stale timestamp
by having drm_crtc_vblank_off update the timestamp to now.
This was seen while debugging weston log message:
Warning: computed repaint delay is insane: -8212 msec
This occurred due to:
1. driver starts up
2. fbcon comes along and restores fbdev, enabling vblank
3. vblank_disable_fn fires via timer disabling vblank, keeping vblank
seq number and time set at current value
(some time later)
4. weston starts and does a modeset
5. atomic commit disables crtc while it does the modeset
6. ipu_crtc_atomic_disable sends vblank with old seq number and time
Fixes: a474478642 ("drm/imx: fix crtc vblank state regression")
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Pull tracing fixes from Steven Rostedt:
"This includes three fixes:
- Fix a deadlock from a previous fix to keep module loading and
function tracing text modifications from stepping on each other
(this has a few patches to help document the issue in comments)
- Fix a crash when the snapshot buffer gets out of sync with the main
ring buffer
- Fix a memory leak when reading the memory logs"
* tag 'trace-v5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Anotate text_mutex split between ftrace_arch_code_modify_post_process() and ftrace_arch_code_modify_prepare()
tracing/snapshot: Resize spare buffer if size changed
tracing: Fix memory leak in tracing_err_log_open()
ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()
ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()
Pull GPIO fix from Linus Walleij:
"A single fixup for the SPI CS gpios that regressed in the current
kernel cycle"
* tag 'gpio-v5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/spi: Fix spi-gpio regression on active high CS
Since commit 10a68cdf10 (nfsd: fix performance-limiting session
calculation) (Linux 5.1-rc1 and 4.19.31), shares from NFS servers with
1 TB of memory cannot be mounted anymore. The mount just hangs on the
client.
The gist of commit 10a68cdf10 is the change below.
-avail = clamp_t(int, avail, slotsize, avail/3);
+avail = clamp_t(int, avail, slotsize, total_avail/3);
Here are the macros.
#define min_t(type, x, y) __careful_cmp((type)(x), (type)(y), <)
#define clamp_t(type, val, lo, hi) min_t(type, max_t(type, val, lo), hi)
`total_avail` is 8,434,659,328 on the 1 TB machine. `clamp_t()` casts
the values to `int`, which for 32-bit integers can only hold values
−2,147,483,648 (−2^31) through 2,147,483,647 (2^31 − 1).
`avail` (in the function signature) is just 65536, so that no overflow
was happening. Before the commit the assignment would result in 21845,
and `num = 4`.
When using `total_avail`, it is causing the assignment to be
18446744072226137429 (printed as %lu), and `num` is then 4164608182.
My next guess is, that `nfsd_drc_mem_used` is then exceeded, and the
server thinks there is no memory available any more for this client.
Updating the arguments of `clamp_t()` and `min_t()` to `unsigned long`
fixes the issue.
Now, `avail = 65536` (before commit 10a68cdf10 `avail = 21845`), but
`num = 4` remains the same.
Fixes: c54f24e338 (nfsd: fix performance-limiting session calculation)
Cc: stable@vger.kernel.org
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Michal Suchanek reported [1] that running the pcrypt_aead01 test from
LTP [2] in a loop and holding Ctrl-C causes a NULL dereference of
alg->cra_users.next in crypto_remove_spawns(), via crypto_del_alg().
The test repeatedly uses CRYPTO_MSG_NEWALG and CRYPTO_MSG_DELALG.
The crash occurs when the instance that CRYPTO_MSG_DELALG is trying to
unregister isn't a real registered algorithm, but rather is a "test
larval", which is a special "algorithm" added to the algorithms list
while the real algorithm is still being tested. Larvals don't have
initialized cra_users, so that causes the crash. Normally pcrypt_aead01
doesn't trigger this because CRYPTO_MSG_NEWALG waits for the algorithm
to be tested; however, CRYPTO_MSG_NEWALG returns early when interrupted.
Everything else in the "crypto user configuration" API has this same bug
too, i.e. it inappropriately allows operating on larval algorithms
(though it doesn't look like the other cases can cause a crash).
Fix this by making crypto_alg_match() exclude larval algorithms.
[1] https://lkml.kernel.org/r/20190625071624.27039-1-msuchanek@suse.de
[2] https://github.com/linux-test-project/ltp/blob/20190517/testcases/kernel/crypto/pcrypt_aead01.c
Reported-by: Michal Suchanek <msuchanek@suse.de>
Fixes: a38f7907b9 ("crypto: Add userspace configuration API")
Cc: <stable@vger.kernel.org> # v3.2+
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
cryptd_skcipher_free() fails to free the struct skcipher_instance
allocated in cryptd_create_skcipher(), leading to a memory leak. This
is detected by kmemleak on bootup on ARM64 platforms:
unreferenced object 0xffff80003377b180 (size 1024):
comm "cryptomgr_probe", pid 822, jiffies 4294894830 (age 52.760s)
backtrace:
kmem_cache_alloc_trace+0x270/0x2d0
cryptd_create+0x990/0x124c
cryptomgr_probe+0x5c/0x1e8
kthread+0x258/0x318
ret_from_fork+0x10/0x1c
Fixes: 4e0958d19b ("crypto: cryptd - Add support for skcipher")
Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull cifs fix from Steve French:
"SMB3 fix (for stable as well) for crash mishandling one of the Windows
reparse point symlink tags"
* tag '5.2-rc6-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix crash querying symlinks stored as reparse-points
Pull pidfd fork() fix from Christian Brauner:
"A single small fix for copy_process() in kernel/fork.c:
With Al's removal of ksys_close() from cleanup paths in copy_process()
a bug was introduced. When anon_inode_getfile() failed the cleanup was
correctly performed but the error code was not propagated to callers
of copy_process() causing them to operate on a nonsensical pointer.
The fix is a simple on-liner which makes sure that a proper negative
error code is returned from copy_process().
syzkaller has also verified that the bug is not reproducible with this
fix"
* tag 'for-linus-20190701' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: return proper negative error code
Pull arm64 fixes from Will Deacon:
"Fix a build failure with the LLVM linker and a module allocation
failure when KASLR is active:
- Fix module allocation when running with KASLR enabled
- Fix broken build due to bug in LLVM linker (ld.lld)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly
arm64: kaslr: keep modules inside module region when KASAN is enabled
This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.
* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
+ Linux 5.2-rc7
Signed-off-by: Olof Johansson <olof@lixom.net>
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value
[ 66.011660] Security negotiation failed.
[ 66.012443] iSCSI Login negotiation failed.
[ 68.413924] general protection fault: 0000 [#1] SMP PTI
[ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1
[ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I ran into an intriguing bug caused by
commit ""spi: gpio: Don't request CS GPIO in DT use-case"
affecting all SPI GPIO devices with an active high
chip select line.
The commit switches the CS gpio handling over to the GPIO
core, which will parse and handle "cs-gpios" from the OF
node without even calling down to the driver to get the
job done.
However the GPIO core handles the standard bindings in
Documentation/devicetree/bindings/spi/spi-controller.yaml
that specifies that active high CS needs to be specified
using "spi-cs-high" in the DT node.
The code in drivers/spi/spi-gpio.c never respected this
and never tried to inspect subnodes to see if they contained
"spi-cs-high" like the gpiolib OF quirks does. Instead the
only way to get an active high CS was to tag it in the
device tree using the flags cell such as
cs-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
This alters the quirks to not inspect the subnodes of SPI
masters on "spi-gpio" for the standard attribute "spi-cs-high",
making old device trees work as expected.
This semantic is a bit ambigous, but just allowing the
flags on the GPIO descriptor to modify polarity is what
the kernel at large mostly uses so let's encourage that.
Fixes: 249e2632dc ("spi: gpio: Don't request CS GPIO in DT use-case")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ftrace_arch_code_modify_prepare() is acquiring text_mutex, while the
corresponding release is happening in ftrace_arch_code_modify_post_process().
This has already been documented in the code, but let's also make the fact
that this is intentional clear to the semantic analysis tools such as sparse.
Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1906292321170.27227@cbobk.fhfr.pm
Fixes: 39611265ed ("ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()")
Fixes: d5b844a2cf ("ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls. The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.
This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.
Reported-by: syzbot+219f00fb49874dcaea17@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thomas reported that:
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rong Chen <rong.a.chen@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently KVM_STATE_NESTED_EVMCS is used to signal that eVMCS
capability is enabled on vCPU.
As indicated by vmx->nested.enlightened_vmcs_enabled.
This is quite bizarre as userspace VMM should make sure to expose
same vCPU with same CPUID values in both source and destination.
In case vCPU is exposed with eVMCS support on CPUID, it is also
expected to enable KVM_CAP_HYPERV_ENLIGHTENED_VMCS capability.
Therefore, KVM_STATE_NESTED_EVMCS is redundant.
KVM_STATE_NESTED_EVMCS is currently used on restore path
(vmx_set_nested_state()) only to enable eVMCS capability in KVM
and to signal need_vmcs12_sync such that on next VMEntry to guest
nested_sync_from_vmcs12() will be called to sync vmcs12 content
into eVMCS in guest memory.
However, because restore nested-state is rare enough, we could
have just modified vmx_set_nested_state() to always signal
need_vmcs12_sync.
From all the above, it seems that we could have just removed
the usage of KVM_STATE_NESTED_EVMCS. However, in order to preserve
backwards migration compatibility, we cannot do that.
(vmx_get_nested_state() needs to signal flag when migrating from
new kernel to old kernel).
Returning KVM_STATE_NESTED_EVMCS when just vCPU have eVMCS enabled
have a bad side-effect of userspace VMM having to send nested-state
from source to destination as part of migration stream. Even if
guest have never used eVMCS as it doesn't even run a nested
hypervisor workload. This requires destination userspace VMM and
KVM to support setting nested-state. Which make it more difficult
to migrate from new host to older host.
To avoid this, change KVM_STATE_NESTED_EVMCS to signal eVMCS is
not only enabled but also active. i.e. Guest have made some
eVMCS active via an enlightened VMEntry. i.e. vmcs12 is copied
from eVMCS and therefore should be restored into eVMCS resident
in memory (by copy_vmcs12_to_enlightened()).
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As comment in code specifies, SMM temporarily disables VMX so we cannot
be in guest mode, nor can VMLAUNCH/VMRESUME be pending.
However, code currently assumes that these are the only flags that can be
set on kvm_state->flags. This is not true as KVM_STATE_NESTED_EVMCS
can also be set on this field to signal that eVMCS should be enabled.
Therefore, fix code to check for guest-mode and pending VMLAUNCH/VMRESUME
explicitly.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The fixed regulator driver doesn't specify any con_id for gpio lookup
so it must be NULL in the table entry.
Fixes: 274e4c3361 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c3361 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Despite what I think the prm recommends, commit f2253bd985
("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context") turned out
to be a huge mistake when enabling Ironlake contexts as the GPU would
hang on either a MI_FLUSH or PIPE_CONTROL immediately following the
MI_SET_CONTEXT of an active mesa context (more vanilla contexts, e.g.
simple rendercopies with igt, do not suffer).
Ville found the following clue,
"[DevCTG+]: For the invalidate operation of the pipe control, the
following pointers are affected. The
invalidate operation affects the restore of these packets. If the pipe
control invalidate operation is completed
before the context save, the indirect pointers will not be restored from
memory.
1. Pipeline State Pointer
2. Media State Pointer
3. Constant Buffer Packet"
which suggests by us emitting the INVALIDATE prior to the MI_SET_CONTEXT,
we prevent the context-restore from chasing the dangling pointers within
the image, and explains why this likely prevents the GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419111749.3910-1-chris@chris-wilson.co.uk
(cherry picked from commit 928f8f4231 in drm-intel-next)
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111014
Fixes: f2253bd985 ("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The irqchip driver depends on the SoC specific driver, but we want
to be able to compile-test it elsewhere:
WARNING: unmet direct dependencies detected for TI_SCI_INTA_MSI_DOMAIN
Depends on [n]: SOC_TI [=n]
Selected by [y]:
- TI_SCI_INTA_IRQCHIP [=y] && TI_SCI_PROTOCOL [=y]
drivers/irqchip/irq-ti-sci-inta.o: In function `ti_sci_inta_irq_domain_probe':
irq-ti-sci-inta.c:(.text+0x204): undefined reference to `ti_sci_inta_msi_create_irq_domain'
Rearrange the Kconfig and Makefile so we build the soc driver whenever
its users are there, regardless of the SOC_TI option.
Fixes: 49b323157b ("soc: ti: Add MSI domain bus support for Interrupt Aggregator")
Fixes: f011df6179 ("irqchip/ti-sci-inta: Add msi domain support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 5.2 (part 2)
Use the armada-38x-uart compatible strings for Armada XP 98dx3236 SoCs
in order to not loose character anymore.
* tag 'mvebu-fixes-5.2-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx3236: Switch to armada-38x-uart serial node
Signed-off-by: Olof Johansson <olof@lixom.net>
The widget_mutex was introduced to serialize callers to
hda_widget_sysfs_{re}init. However, its protection of the sysfs widget array
is incomplete. For example, it is acquired around the call to
hda_widget_sysfs_reinit(), which actually creates the new array, but isn't
still acquired when codec->num_nodes and codec->start_nid is updated. So
the lock ensures one thread sets up the new array at a time, but doesn't
ensure which thread's value will end up in codec->num_nodes. If a larger
num_nodes wins but a smaller array was set up, the next call to
refresh_widgets() will touch free memory as it iterates over codec->num_nodes
that aren't there.
The widget_lock really protects both the tree as well as codec->num_nodes,
start_nid, and end_nid, so make sure it's held across that update. It should
also be held during snd_hdac_get_sub_nodes(), so that a very old read from that
function doesn't end up clobbering a later update.
Fixes: ed180abba7 ("ALSA: hda: Fix race between creating and refreshing sysfs entries")
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, 8 MIDI data streams are multiplexed into single
MIDI conformant data channel. The index of stream is calculated by
modulo 8 of the value of data block counter.
In fireworks, the value of data block counter in CIP header has a quirk
with firmware version v5.0.0, v5.7.3 and v5.8.0. This brings ALSA
IEC 61883-1/6 packet streaming engine to miss detection of MIDI
messages.
This commit fixes the miss detection to modify the value of data block
counter for the modulo calculation.
For maintainers, this bug exists since a commit 18f5ed365d ("ALSA:
fireworks/firewire-lib: add support for recent firmware quirk") in Linux
kernel v4.2. There're many changes since the commit. This fix can be
backported to Linux kernel v4.4 or later. I tagged a base commit to the
backport for your convenience.
Besides, my work for Linux kernel v5.3 brings heavy code refactoring and
some structure members are renamed in 'sound/firewire/amdtp-stream.h'.
The content of this patch brings conflict when merging -rc tree with
this patch and the latest tree. I request maintainers to solve the
conflict to replace 'tx_first_dbc' with 'ctx_data.tx.first_dbc'.
Fixes: df075feefb ("ALSA: firewire-lib: complete AM824 data block processing layer")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sys_move_mount() crashes by dereferencing the pointer MNT_NS_INTERNAL,
a.k.a. ERR_PTR(-EINVAL), if the old mount is specified by fd for a
kernel object with an internal mount, such as a pipe or memfd.
Fix it by checking for this case and returning -EINVAL.
[AV: what we want is is_mounted(); use that instead of making the
condition even more convoluted]
Reproducer:
#include <unistd.h>
#define __NR_move_mount 429
#define MOVE_MOUNT_F_EMPTY_PATH 0x00000004
int main()
{
int fds[2];
pipe(fds);
syscall(__NR_move_mount, fds[0], "", -1, "/", MOVE_MOUNT_F_EMPTY_PATH);
}
Reported-by: syzbot+6004acbaa1893ad013f0@syzkaller.appspotmail.com
Fixes: 2db154b3ea ("vfs: syscall: Add move_mount(2) to move mounts around")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
I'm not entirely sure why this is, but for some reason:
921935dc64 ("drm/amd/powerplay: enforce display related settings only on needed")
Breaks runtime PM resume on the Radeon PRO WX 3100 (Lexa) in one the
pre-production laptops I have. The issue manifests as the following
messages in dmesg:
[drm] UVD and UVD ENC initialized successfully.
amdgpu 0000:3b:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vce1 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <vce_v3_0> failed -110
[drm:amdgpu_device_resume [amdgpu]] *ERROR* amdgpu_device_ip_resume failed (-110).
And happens after about 6-10 runtime PM suspend/resume cycles (sometimes
sooner, if you're lucky!). Unfortunately I can't seem to pin down
precisely which part in psm_adjust_power_state_dynamic that is causing
the issue, but not skipping the display setting setup seems to fix it.
Hopefully if there is a better fix for this, this patch will spark
discussion around it.
Fixes: 921935dc64 ("drm/amd/powerplay: enforce display related settings only on needed")
Cc: Evan Quan <evan.quan@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: Rex Zhu <Rex.Zhu@amd.com>
Cc: Likun Gao <Likun.Gao@amd.com>
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If MTD_NAND_JZ4780 is y and MTD_NAND_JZ4780_BCH is m,
which select CONFIG_MTD_NAND_INGENIC_ECC to m, building fails:
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_remove':
ingenic_nand.c:(.text+0x177): undefined reference to `ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_nand.o: In function `ingenic_nand_ecc_correct':
ingenic_nand.c:(.text+0x2ee): undefined reference to `ingenic_ecc_correct'
To fix that, the ingenic_nand and ingenic_ecc modules have been fused
into one single module.
- The ingenic_ecc.c code is now compiled in only if
$(CONFIG_MTD_NAND_INGENIC_ECC) is set. This is now a boolean instead
of tristate.
- To avoid changing the module name, the ingenic_nand.c file is moved to
ingenic_nand_drv.c. Then the module name is still ingenic_nand.
- Since ingenic_ecc.c is no more a module, the module-specific macros
have been dropped, and the functions are no more exported for use by
the ingenic_nand driver.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Hulk Robot <hulkci@huawei.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 1Gb Macronix chip can have a maximum of 20 bad blocks, while
the 2Gb version has twice as many blocks and therefore the maximum
number of bad blocks is 40.
The 4Gb GigaDevice GD5F4GQ4xA has twice as many blocks as its 2Gb
counterpart and therefore a maximum of 80 bad blocks.
Fixes: 377e517b5f ("mtd: nand: Add max_bad_eraseblocks_per_lun info to memorg")
Reported-by: Emil Lenngren <emil.lenngren@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
drm_gem_shmem_create_with_handle() returns a GEM object and attach a
handle to it. When the user closes the DRM FD, the core releases all
GEM handles along with their backing GEM objs, which can lead to a
double-free issue if panfrost_ioctl_create_bo() failed and went
through the err_free path where drm_gem_object_put_unlocked() is
called without deleting the associate handle.
Replace this drm_gem_object_put_unlocked() call by a
drm_gem_handle_delete() one to fix that.
Fixes: f3ba91228e ("drm/panfrost: Add initial panfrost driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627172414.27231-1-boris.brezillon@collabora.com
Taking the text_mutex in ftrace_arch_code_modify_prepare() is to fix a
race against module loading and live kernel patching that might try to
change the text permissions while ftrace has it as read/write. This
really needs to be documented in the code. Add a comment that does such.
Link: http://lkml.kernel.org/r/20190627211819.5a591f52@gandalf.local.home
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The commit 9f255b632b ("module: Fix livepatch/ftrace module text
permissions race") causes a possible deadlock between register_kprobe()
and ftrace_run_update_code() when ftrace is using stop_machine().
The existing dependency chain (in reverse order) is:
-> #1 (text_mutex){+.+.}:
validate_chain.isra.21+0xb32/0xd70
__lock_acquire+0x4b8/0x928
lock_acquire+0x102/0x230
__mutex_lock+0x88/0x908
mutex_lock_nested+0x32/0x40
register_kprobe+0x254/0x658
init_kprobes+0x11a/0x168
do_one_initcall+0x70/0x318
kernel_init_freeable+0x456/0x508
kernel_init+0x22/0x150
ret_from_fork+0x30/0x34
kernel_thread_starter+0x0/0xc
-> #0 (cpu_hotplug_lock.rw_sem){++++}:
check_prev_add+0x90c/0xde0
validate_chain.isra.21+0xb32/0xd70
__lock_acquire+0x4b8/0x928
lock_acquire+0x102/0x230
cpus_read_lock+0x62/0xd0
stop_machine+0x2e/0x60
arch_ftrace_update_code+0x2e/0x40
ftrace_run_update_code+0x40/0xa0
ftrace_startup+0xb2/0x168
register_ftrace_function+0x64/0x88
klp_patch_object+0x1a2/0x290
klp_enable_patch+0x554/0x980
do_one_initcall+0x70/0x318
do_init_module+0x6e/0x250
load_module+0x1782/0x1990
__s390x_sys_finit_module+0xaa/0xf0
system_call+0xd8/0x2d0
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(text_mutex);
lock(cpu_hotplug_lock.rw_sem);
lock(text_mutex);
lock(cpu_hotplug_lock.rw_sem);
It is similar problem that has been solved by the commit 2d1e38f566
("kprobes: Cure hotplug lock ordering issues"). Many locks are involved.
To be on the safe side, text_mutex must become a low level lock taken
after cpu_hotplug_lock.rw_sem.
This can't be achieved easily with the current ftrace design.
For example, arm calls set_all_modules_text_rw() already in
ftrace_arch_code_modify_prepare(), see arch/arm/kernel/ftrace.c.
This functions is called:
+ outside stop_machine() from ftrace_run_update_code()
+ without stop_machine() from ftrace_module_enable()
Fortunately, the problematic fix is needed only on x86_64. It is
the only architecture that calls set_all_modules_text_rw()
in ftrace path and supports livepatching at the same time.
Therefore it is enough to move text_mutex handling from the generic
kernel/trace/ftrace.c into arch/x86/kernel/ftrace.c:
ftrace_arch_code_modify_prepare()
ftrace_arch_code_modify_post_process()
This patch basically reverts the ftrace part of the problematic
commit 9f255b632b ("module: Fix livepatch/ftrace module
text permissions race"). And provides x86_64 specific-fix.
Some refactoring of the ftrace code will be needed when livepatching
is implemented for arm or nds32. These architectures call
set_all_modules_text_rw() and use stop_machine() at the same time.
Link: http://lkml.kernel.org/r/20190627081334.12793-1-pmladek@suse.com
Fixes: 9f255b632b ("module: Fix livepatch/ftrace module text permissions race")
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
[
As reviewed by Miroslav Benes <mbenes@suse.cz>, removed return value of
ftrace_run_update_code() as it is a void function.
]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There are two occurrances of a call to snd_seq_oss_fill_addr where
the dest_client and dest_port arguments are in the wrong order. Fix
this by swapping them around.
Addresses-Coverity: ("Arguments in wrong order")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On M710q Lenovo ThinkCentre machine, there are two front mics,
we change the location for one of them to avoid conflicts.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When something goes wrong in the GPU init after the cmdbuf suballocator
has been constructed, we fail to destroy it properly. This causes havok
later when the GPU is unbound due to a module unload or similar.
Fixes: e66774dd6f (drm/etnaviv: add cmdbuf suballocator)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
There are a couple of left shifts of unsigned 8 bit values that
first get promoted to signed ints and hence get sign extended
on the shift if the top bit of the 8 bit values are set. Fix
this by casting the 8 bit values to unsigned ints to stop the
unintentional sign extension.
Addresses-Coverity: ("Unintended sign extension")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We never parsed/returned any data from .get_link() when the object is a windows reparse-point
containing a symlink. This results in the VFS layer oopsing accessing an uninitialized buffer:
...
[ 171.407172] Call Trace:
[ 171.408039] readlink_copy+0x29/0x70
[ 171.408872] vfs_readlink+0xc1/0x1f0
[ 171.409709] ? readlink_copy+0x70/0x70
[ 171.410565] ? simple_attr_release+0x30/0x30
[ 171.411446] ? getname_flags+0x105/0x2a0
[ 171.412231] do_readlinkat+0x1b7/0x1e0
[ 171.412938] ? __ia32_compat_sys_newfstat+0x30/0x30
...
Fix this by adding code to handle these buffers and make sure we do return a valid buffer
to .get_link()
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
After r363059 and r363928 in LLVM, a build using ld.lld as the linker
with CONFIG_RANDOMIZE_BASE enabled fails like so:
ld.lld: error: relocation R_AARCH64_ABS32 cannot be used against symbol
__efistub_stext_offset; recompile with -fPIC
Fangrui and Peter figured out that ld.lld is incorrectly considering
__efistub_stext_offset as a relative symbol because of the order in
which symbols are evaluated. _text is treated as an absolute symbol
and stext is a relative symbol, making __efistub_stext_offset a
relative symbol.
Adding ABSOLUTE will force ld.lld to evalute this expression in the
right context and does not change ld.bfd's behavior. ld.lld will
need to be fixed but the developers do not see a quick or simple fix
without some research (see the linked issue for further explanation).
Add this simple workaround so that ld.lld can continue to link kernels.
Link: https://github.com/ClangBuiltLinux/linux/issues/561
Link: 025a815d75
Link: 249fde8583
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Debugged-by: Fangrui Song <maskray@google.com>
Debugged-by: Peter Smith <peter.smith@linaro.org>
Suggested-by: Fangrui Song <maskray@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[will: add comment]
Signed-off-by: Will Deacon <will@kernel.org>
When KASLR and KASAN are both enabled, we keep the modules where they
are, and randomize the placement of the kernel so it is within 2 GB
of the module region. The reason for this is that putting modules in
the vmalloc region (like we normally do when KASLR is enabled) is not
possible in this case, given that the entire vmalloc region is already
backed by KASAN zero shadow pages, and so allocating dedicated KASAN
shadow space as required by loaded modules is not possible.
The default module allocation window is set to [_etext - 128MB, _etext]
in kaslr.c, which is appropriate for KASLR kernels booted without a
seed or with 'nokaslr' on the command line. However, as it turns out,
it is not quite correct for the KASAN case, since it still intersects
the vmalloc region at the top, where attempts to allocate shadow pages
will collide with the KASAN zero shadow pages, causing a WARN() and all
kinds of other trouble. So cap the top end to MODULES_END explicitly
when running with KASAN.
Cc: <stable@vger.kernel.org> # 4.9+
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
This adds 4 SND_PCI_QUIRK(...) lines for several barebone models of the ODM
Clevo. The model names are written in regex syntax to describe/match all clevo
models that are similar enough and use the same PCI SSID that this fixup works
for them.
Additionally the lines regarding SSID 0x96e1 and 0x97e1 didn't fix audio for the
all our Clevo notebooks using these SSIDs (models Clevo P960* and P970*) since
ALC1220_FIXP_CLEVO_PB51ED_PINS swapped pins that are not necesarry to be
swapped. This patch initiates ALC1220_FIXUP_CLEVO_P950 instead for these model
and fixes the audio.
Fixes: 80690a276f ("ALSA: hda/realtek - Add quirk for Tuxedo XC 1509")
Signed-off-by: Richard Sailer <rs@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a missing EHB (Execution Hazard Barrier) in mtc0 -> mfc0 sequence.
Without this execution hazard barrier it's possible for the value read
back from the KScratch register to be the value from before the mtc0.
Reproducible on P5600 & P6600.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
Signed-off-by: Dmitry Korotin <dkorotin@wavecomp.com>
[paul.burton@mips.com:
- Commit message tweaks.
- Add Fixes tags.
- Mark for stable back to v3.15 where P5600 support was introduced.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3d8bfdd030 ("MIPS: Use C0_KScratch (if present) to hold PGD pointer.")
Fixes: 829dcc0a95 ("MIPS: Add MIPS P5600 probe support")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v3.15+
scripts/package/builddeb calls "make dtbs_install" after executing
a plain make (i.e. no build targets specified). It will fail if dtbs
were not built beforehand. Match the arm64 architecture where DTBs get
built by the "all" target.
Signed-off-by: Cedric Hombourger <Cedric_Hombourger@mentor.com>
[paul.burton@mips.com: s/builddep/builddeb]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.1+
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
The DRC appears to be effectively empty after an RPC/RDMA transport
reconnect. The problem is that each connection uses a different
source port, which defeats the DRC hash.
Clients always have to disconnect before they send retransmissions
to reset the connection's credit accounting, thus every retransmit
on NFS/RDMA will miss the DRC.
An NFS/RDMA client's IP source port is meaningless for RDMA
transports. The transport layer typically sets the source port value
on the connection to a random ephemeral port. The server already
ignores it for the "secure port" check. See commit 16e4d93f6d
("NFSD: Ignore client's source port on RDMA transports").
The Linux NFS server's DRC resolves XID collisions from the same
source IP address by using the checksum of the first 200 bytes of
the RPC call header.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
While trying to get the uart with parity working I found setting even
parity enabled odd parity insted. Fix the register settings to match
the datasheet of AR9331.
A similar patch was created by 8devices, but not sent upstream.
77c5586ade
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
When inserting entry into xarray, we store mapping and index in
corresponding struct pages for memory error handling. When it happened
that one process was mapping file at PMD granularity while another
process at PTE granularity, we could wrongly deassociate PMD range and
then reassociate PTE range leaving the rest of struct pages in PMD range
without mapping information which could later cause missed notifications
about memory errors. Fix the problem by calling the association /
deassociation code if and only if we are really going to update the
xarray (deassociating and associating zero or empty entries is just
no-op so there's no reason to complicate the code with trying to avoid
the calls for these cases).
Cc: <stable@vger.kernel.org>
Fixes: d2c997c0f1 ("fs, dax: use page->mapping to warn if truncate...")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2019-06-06 22:18:49 -07:00
81 changed files with 492 additions and 313 deletions
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
