Pull ARM fixes from Russell King:
"A small number of ARM fixes
- Fix function tracer and unwinder dependencies so that we don't end
up building kernels that will crash
- Fix ARMv7M nommu initialisation (missing register initialisation)
- Fix EFI decompressor entry (ensuring barrier instructions are
enabled prior to use)"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache
ARM: 8856/1: NOMMU: Fix CCR register faulty initialization when MPU is disabled
ARM: fix function graph tracer and unwinder dependencies
Pull powerpc fixes from Michael Ellerman:
"A one-liner to make our Radix MMU support depend on HUGETLB_PAGE. We
use some of the hugetlb inlines (eg. pud_huge()) when operating on the
linear mapping and if they're compiled into empty wrappers we can
corrupt memory.
Then two fixes to our VFIO IOMMU code. The first is not a regression
but fixes the locking to avoid a user-triggerable deadlock.
The second does fix a regression since rc1, and depends on the first
fix. It makes it possible to run guests with large amounts of memory
again (~256GB).
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.1-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm_iommu: Allow pinning large regions
powerpc/mm_iommu: Fix potential deadlock
powerpc/mm/radix: Make Radix require HUGETLB_PAGE
Pull block fixes from Jens Axboe:
"A set of io_uring fixes that should go into this release. In
particular, this contains:
- The mutex lock vs ctx ref count fix (me)
- Removal of a dead variable (me)
- Two race fixes (Stefan)
- Ring head/tail condition fix for poll full SQ detection (Stefan)"
* tag 'for-linus-20190428' of git://git.kernel.dk/linux-block:
io_uring: remove 'state' argument from io_{read,write} path
io_uring: fix poll full SQ detection
io_uring: fix race condition when sq threads goes sleeping
io_uring: fix race condition reading SQ entries
io_uring: fail io_uring_register(2) on a dying io_uring instance
Pull rdma fixes from Jason Gunthorpe:
"One core bug fix and a few driver ones
- FRWR memory registration for hfi1/qib didn't work with with some
iovas causing a NFSoRDMA failure regression due to a fix in the NFS
side
- A command flow error in mlx5 allowed user space to send a corrupt
command (and also smash the kernel stack we've since learned)
- Fix a regression and some bugs with device hot unplug that was
discovered while reviewing Andrea's patches
- hns has a failure if the user asks for certain QP configurations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Bugfix for mapping user db
RDMA/ucontext: Fix regression with disassociate
RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages
RDMA/mlx5: Do not allow the user to write to the clock page
IB/mlx5: Fix scatter to CQE in DCT QP creation
IB/rdmavt: Fix frwr memory registration
Pull dmaengine fixes from Vinod Koul:
- fix for wrong register use in mediatek driver
- fix in sh driver for glitch is tx_status and treating 0 a valid
residue for cyclic
- fix in bcm driver for using right memory allocation flag
* tag 'dmaengine-fix-5.1-rc7' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: mediatek-cqdma: fix wrong register usage in mtk_cqdma_start
dmaengine: sh: rcar-dmac: Fix glitch in dmaengine_tx_status
dmaengine: sh: rcar-dmac: With cyclic DMA residue 0 is valid
dmaengine: bcm2835: Avoid GFP_KERNEL in device_prep_slave_sg
Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups for Synaptics RMI4 driver and allowing
snvs_pwrkey to be selected on more boards"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - write config register values to the right offset
Input: synaptics-rmi4 - fix possible double free
Input: snvs_pwrkey - make it depend on ARCH_MXC
Pull x86 fixes from Ingo Molnar:
- Fix an early boot crash in the RSDP parsing code by effectively
turning off the parsing call - we ran out of time but want to fix the
regression. The more involved fix is being worked on.
- Fix a crash that can trigger in the kmemlek code.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix a crash with kmemleak_scan()
x86/boot: Disable RSDP parsing temporarily
Pull scheduler fix from Ingo Molnar:
"Fix a division by zero bug that can trigger in the NUMA placement
code"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Fix a possible divide-by-zero
Pull perf fix from Ingo Molnar:
"A cstate event enumeration fix for Kaby/Coffee Lake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Update KBL Package C-state events to also include PC8/PC9/PC10 counters
This way, slhc_free() accepts what slhc_init() returns, whether that is
an error or not.
In particular, the pattern in sl_alloc_bufs() is
slcomp = slhc_init(16, 16);
...
slhc_free(slcomp);
for the error handling path, and rather than complicate that code, just
make it ok to always free what was returned by the init function.
That's what the code used to do before commit 4ab42d78e3 ("ppp, slip:
Validate VJ compression slot parameters completely") when slhc_init()
just returned NULL for the error case, with no actual indication of the
details of the error.
Reported-by: syzbot+45474c076a4927533d2e@syzkaller.appspotmail.com
Fixes: 4ab42d78e3 ("ppp, slip: Validate VJ compression slot parameters completely")
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/proc/proc_sysctl.c: Fix a NULL pointer dereference
mm/page_alloc.c: fix never set ALLOC_NOFRAGMENT flag
mm/page_alloc.c: avoid potential NULL pointer dereference
mm, page_alloc: always use a captured page regardless of compaction result
mm: do not boost watermarks to avoid fragmentation for the DISCONTIG memory model
lib/test_vmalloc.c: do not create cpumask_t variable on stack
lib/Kconfig.debug: fix build error without CONFIG_BLOCK
zram: pass down the bvec we need to read into in the work struct
mm/memory_hotplug.c: drop memory device reference after find_memory_block()
Currently any changed config register values don't take effect, as the
function to write them back is called with the wrong register offset.
Fixes: ff8f83708b (Input: synaptics-rmi4 - add support for 2D
sensors and F11)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull arm64 fixes from Catalin Marinas:
- keep the tail of an unaligned initrd reserved
- adjust ftrace_make_call() to deal with the relative nature of PLTs
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/module: ftrace: deal with place relative nature of PLTs
arm64: mm: Ensure tail of unaligned initrd is reserved
Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:
- Use "nosteal" for ring buffer splice pages
- Memory leak fix in error path of trace_pid_write()
- Fix preempt_enable_no_resched() (use preempt_enable()) in ring
buffer code"
* tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
trace: Fix preempt_enable_no_resched() abuse
tracing: Fix a memory leak by early error exit in trace_pid_write()
tracing: Fix buffer_ref pipe ops
Pull GPIO fixes from Linus Walleij:
"Not much to say about them, regular fixes:
- Fix a bug on the errorpath of gpiochip_add_data_with_key()
- IRQ type setting on the spreadtrum GPIO driver"
* tag 'gpio-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix gpiochip_add_data_with_key() error path
gpio: eic: sprd: Fix incorrect irq type setting for the sync EIC
Pull btrfs fix from David Sterba:
"One patch to fix a crash in io submission path, due to memory
allocation errors.
In short, the multipage bio work that landed in 5.1 caused larger bios
that in turn require larger temporary memory for checksums. The patch
is a workaround, we're going to rework the allocation so it does not
require the vmalloc fallback.
It took a while to identify that it's caused by patches in 5.1 and not
a patchset that did some changes in error handling in the code. I've
tested it on various memory/cpu combinations, it could hit OOM but
does not crash.
The timestamp of the patch is less than a day due to updates in the
changelog, tests were running meanwhile"
* tag 'for-5.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Switch memory allocations in async csum calculation path to kvmalloc
Pull cifs fixes from Steve French:
"Three small SMB3 fixes (all for stable as well): two leaks and a
rename bug"
* tag '5.1-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix page reference leak with readv/writev
cifs: do not attempt cifs operation on smb2+ rename error
cifs: fix memory leak in SMB2_read
ac.preferred_zoneref->zone passed to alloc_flags_nofragment() can be NULL.
'zone' pointer unconditionally derefernced in alloc_flags_nofragment().
Bail out on NULL zone to avoid potential crash. Currently we don't see
any crashes only because alloc_flags_nofragment() has another bug which
allows compiler to optimize away all accesses to 'zone'.
Link: http://lkml.kernel.org/r/20190423120806.3503-1-aryabinin@virtuozzo.com
Fixes: 6bb154504f ("mm, page_alloc: spread allocations across zones before introducing fragmentation")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the development of commit 5e1f0f098b ("mm, compaction: capture
a page under direct compaction"), a paranoid check was added to ensure
that if a captured page was available after compaction that it was
consistent with the final state of compaction. The intent was to catch
serious programming bugs such as using a stale page pointer and causing
corruption problems.
However, it is possible to get a captured page even if compaction was
unsuccessful if an interrupt triggered and happened to free pages in
interrupt context that got merged into a suitable high-order page. It's
highly unlikely but Li Wang did report the following warning on s390
occuring when testing OOM handling. Note that the warning is slightly
edited for clarity.
WARNING: CPU: 0 PID: 9783 at mm/page_alloc.c:3777 __alloc_pages_direct_compact+0x182/0x190
Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs
lockd grace fscache sunrpc pkey ghash_s390 prng xts aes_s390
des_s390 des_generic sha512_s390 zcrypt_cex4 zcrypt vmur binfmt_misc
ip_tables xfs libcrc32c dasd_fba_mod qeth_l2 dasd_eckd_mod dasd_mod
qeth qdio lcs ctcm ccwgroup fsm dm_mirror dm_region_hash dm_log
dm_mod
CPU: 0 PID: 9783 Comm: copy.sh Kdump: loaded Not tainted 5.1.0-rc 5 #1
This patch simply removes the check entirely instead of trying to be
clever about pages freed from interrupt context. If a serious
programming error was introduced, it is highly likely to be caught by
prep_new_page() instead.
Link: http://lkml.kernel.org/r/20190419085133.GH18914@techsingularity.net
Fixes: 5e1f0f098b ("mm, compaction: capture a page under direct compaction")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Li Wang <liwang@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka reported that commit 1c30844d2d ("mm: reclaim small
amounts of memory when an external fragmentation event occurs") "broke"
memory management on parisc.
The machine is not NUMA but the DISCONTIG model creates three pgdats
even though it's a UMA machine for the following ranges
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000000100000000 End 0x00000001bfdfffff Size 3070 MB
2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072 MB
Mikulas reported:
With the patch 1c30844d2, the kernel will incorrectly reclaim the
first zone when it fills up, ignoring the fact that there are two
completely free zones. Basiscally, it limits cache size to 1GiB.
For example, if I run:
# dd if=/dev/sda of=/dev/null bs=1M count=2048
- with the proper kernel, there should be "Buffers - 2GiB"
when this command finishes. With the patch 1c30844d2, buffers
will consume just 1GiB or slightly more, because the kernel was
incorrectly reclaiming them.
The page allocator and reclaim makes assumptions that pgdats really
represent NUMA nodes and zones represent ranges and makes decisions on
that basis. Watermark boosting for small pgdats leads to unexpected
results even though this would have behaved reasonably on SPARSEMEM.
DISCONTIG is essentially deprecated and even parisc plans to move to
SPARSEMEM so there is no need to be fancy, this patch simply disables
watermark boosting by default on DISCONTIGMEM.
Link: http://lkml.kernel.org/r/20190419094335.GJ18914@techsingularity.net
Fixes: 1c30844d2d ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In trace_pid_write(), the buffer for trace parser is allocated through
kmalloc() in trace_parser_get_init(). Later on, after the buffer is used,
it is then freed through kfree() in trace_parser_put(). However, it is
possible that trace_pid_write() is terminated due to unexpected errors,
e.g., ENOMEM. In that case, the allocated buffer will not be freed, which
is a memory leak bug.
To fix this issue, free the allocated buffer when an error is encountered.
Link: http://lkml.kernel.org/r/1555726979-15633-1-git-send-email-wang6495@umn.edu
Fixes: f4d34a87e9 ("tracing: Use pid bitmap instead of a pid array for set_event_pid")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This fixes multiple issues in buffer_pipe_buf_ops:
- The ->steal() handler must not return zero unless the pipe buffer has
the only reference to the page. But generic_pipe_buf_steal() assumes
that every reference to the pipe is tracked by the page's refcount,
which isn't true for these buffers - buffer_pipe_buf_get(), which
duplicates a buffer, doesn't touch the page's refcount.
Fix it by using generic_pipe_buf_nosteal(), which refuses every
attempted theft. It should be easy to actually support ->steal, but the
only current users of pipe_buf_steal() are the virtio console and FUSE,
and they also only use it as an optimization. So it's probably not worth
the effort.
- The ->get() and ->release() handlers can be invoked concurrently on pipe
buffers backed by the same struct buffer_ref. Make them safe against
concurrency by using refcount_t.
- The pointers stored in ->private were only zeroed out when the last
reference to the buffer_ref was dropped. As far as I know, this
shouldn't be necessary anyway, but if we do it, let's always do it.
Link: http://lkml.kernel.org/r/20190404215925.253531-1-jannh@google.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Fixes: 73a757e631 ("ring-buffer: Return reader page back into existing ring buffer")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
drm/imx: fix DP CSC handling
- Fix the DP color space conversion matrix setup to avoid bugs where
disabling the overlay plane while both primary and overlay plane are
routed via the CSC unit would not reconfigure the CSC routing
properly, leaving the display in a nonworking state, or the CSC
setting from a previously set mode would be left behind, causing
wrong colors when reenabling the display in certain configurations.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1556183136.2271.3.camel@pengutronix.de
sched_clock_cpu() may not be consistent between CPUs. If a task
migrates to another CPU, then se.exec_start is set to that CPU's
rq_clock_task() by update_stats_curr_start(). Specifically, the new
value might be before the old value due to clock skew.
So then if in numa_get_avg_runtime() the expression:
'now - p->last_task_numa_placement'
ends up as -1, then the divider '*period + 1' in task_numa_placement()
is 0 and things go bang. Similar to update_curr(), check if time goes
backwards to avoid this.
[ peterz: Wrote new changelog. ]
[ mingo: Tweaked the code comment. ]
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: cj.chengjian@huawei.com
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20190425080016.GX11158@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull ceph fixes from Ilya Dryomov:
"dentry name handling fixes from Jeff and a memory leak fix from Zheng.
Both are old issues, marked for stable"
* tag 'ceph-for-5.1-rc7' of git://github.com/ceph/ceph-client:
ceph: fix ci->i_head_snapc leak
ceph: handle the case where a dentry has been renamed on outstanding req
ceph: ensure d_name stability in ceph_dentry_hash()
ceph: only use d_name directly when parent is locked
Pull crypto fixes from Herbert Xu:
"This fixes a bug in xts and lrw where they may sleep in an atomic
context"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: lrw - Fix atomic sleep when walking skcipher
crypto: xts - Fix atomic sleep when walking skcipher
When the maximum send wr delivered by the user is zero, the qp does not
have a sq.
When allocating the sq db buffer to store the user sq pi pointer and map
it to the kernel mode, max_send_wr is used as the trigger condition, while
the kernel does not consider the max_send_wr trigger condition when
mapmping db. It will cause sq record doorbell map fail and create qp fail.
The failed print information as follows:
hns3 0000:7d:00.1: Send cmd: tail - 418, opcode - 0x8504, flag - 0x0011, retval - 0x0000
hns3 0000:7d:00.1: Send cmd: 0xe59dc000 0x00000000 0x00000000 0x00000000 0x00000116 0x0000ffff
hns3 0000:7d:00.1: sq record doorbell map failed!
hns3 0000:7d:00.1: Create RC QP failed
Fixes: 0425e3e6e0 ("RDMA/hns: Support flush cqe for hip08 in kernel space")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Recent multi-page biovec rework allowed creation of bios that can span
large regions - up to 128 megabytes in the case of btrfs. OTOH btrfs'
submission path currently allocates a contiguous array to store the
checksums for every bio submitted. This means we can request up to
(128mb / BTRFS_SECTOR_SIZE) * 4 bytes + 32bytes of memory from kmalloc.
On busy systems with possibly fragmented memory said kmalloc can fail
which will trigger BUG_ON due to improper error handling IO submission
context in btrfs.
Until error handling is improved or bios in btrfs limited to a more
manageable size (e.g. 1m) let's use kvmalloc to fallback to vmalloc for
such large allocations. There is no hard requirement that the memory
allocated for checksums during IO submission has to be contiguous, but
this is a simple fix that does not require several non-contiguous
allocations.
For small writes this is unlikely to have any visible effect since
kmalloc will still satisfy allocation requests as usual. For larger
requests the code will just fallback to vmalloc.
We've performed evaluation on several workload types and there was no
significant difference kmalloc vs kvmalloc.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When ddc-i2c-bus property is used, a NULL pointer dereference is reported:
[ 31.041669] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[ 31.041671] pgd = 4d3c16f6
[ 31.041673] [00000008] *pgd=00000000
[ 31.041678] Internal error: Oops: 5 [#1] SMP ARM
[ 31.041711] Hardware name: Rockchip (Device Tree)
[ 31.041718] PC is at i2c_transfer+0x8/0xe4
[ 31.041721] LR is at drm_scdc_read+0x54/0x84
[ 31.041723] pc : [<c073273c>] lr : [<c05926c4>] psr: 280f0013
[ 31.041725] sp : edffdad0 ip : 5ccb5511 fp : 00000058
[ 31.041727] r10: 00000780 r9 : edf91608 r8 : c11b0f48
[ 31.041728] r7 : 00000438 r6 : 00000000 r5 : 00000000 r4 : 00000000
[ 31.041730] r3 : edffdae7 r2 : 00000002 r1 : edffdaec r0 : 00000000
[ 31.041908] [<c073273c>] (i2c_transfer) from [<c05926c4>] (drm_scdc_read+0x54/0x84)
[ 31.041913] [<c05926c4>] (drm_scdc_read) from [<c0592858>] (drm_scdc_set_scrambling+0x30/0xbc)
[ 31.041919] [<c0592858>] (drm_scdc_set_scrambling) from [<c05cc0f4>] (dw_hdmi_update_power+0x1440/0x1610)
[ 31.041926] [<c05cc0f4>] (dw_hdmi_update_power) from [<c05cc574>] (dw_hdmi_bridge_enable+0x2c/0x70)
[ 31.041932] [<c05cc574>] (dw_hdmi_bridge_enable) from [<c05aed48>] (drm_bridge_enable+0x24/0x34)
[ 31.041938] [<c05aed48>] (drm_bridge_enable) from [<c0591060>] (drm_atomic_helper_commit_modeset_enables+0x114/0x220)
[ 31.041943] [<c0591060>] (drm_atomic_helper_commit_modeset_enables) from [<c05c3fe0>] (rockchip_atomic_helper_commit_tail_rpm+0x28/0x64)
hdmi->i2c may not be set when ddc-i2c-bus property is used in device tree.
Fix this by using hdmi->ddc as the i2c adapter when calling drm_scdc_*().
Also report that SCDC is not supported when there is no DDC bus.
Fixes: 264fce6cc2 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/VE1PR03MB59031814B5BCAB2152923BDAAC210@VE1PR03MB5903.eurprd03.prod.outlook.com
The err_remove_chip block is too coarse, and may perform cleanup that
must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove()
is still called, causing:
OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
[<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
[<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
[<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc)
[<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c)
[<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314)
[<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)
and later, if a GPIO consumer tries to use a GPIO from a failed
controller:
WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c
refcount_t: increment on 0; use-after-free.
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
[<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
[<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
[<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec)
[<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c)
[<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c)
[<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c)
[<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0)
[<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154)
[<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0)
[<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac)
[<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380)
[<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8)
[<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144)
[<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc)
[<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)
Fix this by splitting the cleanup block, and adding a missing call to
gpiochip_irqchip_remove().
Fixes: 28355f8196 ("gpio: defer probe if pinctrl cannot be found")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove the check for IOMMU presence since it was considered a
layer violation.
This means we have no reliable way to destinguish between coherent
hardware IOMMU DMA address translations and incoherent SWIOTLB DMA
address translations, which we can't handle. So always presume the
former. This means that if anybody forces SWIOTLB without also setting
the vmw_force_coherent=1 vmwgfx option, driver operation will fail,
like it will on most other graphics drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Add a designated reviewer for the LED subsystem as there
are already two maintainers assigned.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Before the commit 490ea5967b ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit 490ea5967b ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M
The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us
cpu %
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.
Fixes: commit 490ea5967b ("RDS: IB: move FMR code to its own file")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vrf device is not able to change mac address now because lack of
ndo_set_mac_address. Complete this in case some apps need to do
this.
Reported-by: Hui Wang <wanghui104@huawei.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A path-based rename returning EBUSY will incorrectly try opening
the file with a cifs (NT Create AndX) operation on an smb2+ mount,
which causes the server to force a session close.
If the mount is smb2+, skip the fallback.
Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When this code was consolidated the intention was that the VMA would
become backed by anonymous zero pages after the zap_vma_pte - however this
very subtly relied on setting the vm_ops = NULL and clearing the VM_SHARED
bits to transform the VMA into an anonymous VMA. Since the vm_ops was
removed this broke.
Now userspace gets a SIGBUS if it touches the vma after disassociation.
Instead of converting the VMA to anonymous provide a fault handler that
puts a zero'd page into the VMA when user-space touches it after
disassociation.
Cc: stable@vger.kernel.org
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Fixes: 5f9794dc94 ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The SNVS power key is not only used on i.MX6SX and i.MX7D, it is also
used by i.MX6UL and NXP's latest ARMv8 based i.MX8M series SOC. So
update the config dependency to use ARCH_MXC, and add the COMPILE_TEST
too.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since mlx5 supports device disassociate it must use this API for all
BAR page mmaps, otherwise the pages can remain mapped after the device
is unplugged causing a system crash.
Cc: stable@vger.kernel.org
Fixes: 5f9794dc94 ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The intent of this VMA was to be read-only from user space, but the
VM_MAYWRITE masking was missed, so mprotect could make it writable.
Cc: stable@vger.kernel.org
Fixes: 5c99eaecb1 ("IB/mlx5: Mmap the HCA's clock info to user-space")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
A pointer to crtc was missing, resulting in the following build error:
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: sparse: incorrect type in argument 1 (different base types)
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: expected struct drm_crtc *crtc
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: got struct drm_crtc_state *state
drivers/gpu/drm/vc4/vc4_crtc.c:1045:39: sparse: sparse: not enough arguments for function vc4_crtc_destroy_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/2b6ed5e6-81b0-4276-8860-870b54ca3262@linux.intel.com
Fixes: d08106796a ("drm/vc4: Fix memory leak during gpu reset.")
Cc: <stable@vger.kernel.org> # v4.6+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first kmemleak_scan() call after boot would trigger the crash below
because this callpath:
kernel_init
free_initmem
mem_encrypt_free_decrypted_mem
free_init_pages
unmaps memory inside the .bss when DEBUG_PAGEALLOC=y.
kmemleak_init() will register the .data/.bss sections and then
kmemleak_scan() will scan those addresses and dereference them looking
for pointer references. If free_init_pages() frees and unmaps pages in
those sections, kmemleak_scan() will crash if referencing one of those
addresses:
BUG: unable to handle kernel paging request at ffffffffbd402000
CPU: 12 PID: 325 Comm: kmemleak Not tainted 5.1.0-rc4+ #4
RIP: 0010:scan_block
Call Trace:
scan_gray_list
kmemleak_scan
kmemleak_scan_thread
kthread
ret_from_fork
Since kmemleak_free_part() is tolerant to unknown objects (not tracked
by kmemleak), it is fine to call it from free_init_pages() even if not
all address ranges passed to this function are known to kmemleak.
[ bp: Massage. ]
Fixes: b3f0907c71 ("x86/mm: Add .bss..decrypted section to hold shared variables")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190423165811.36699-1-cai@lca.pw
Previously BMC's MAC address is calculated by simply adding 1 to the
last byte of network controller's MAC address, and it produces incorrect
result when network controller's MAC address ends with 0xFF.
The problem can be fixed by calling eth_addr_inc() function to increment
MAC address; besides, the MAC address is also validated before assigning
to BMC.
Fixes: cb10c7c0df ("net/ncsi: Add NCSI Broadcom OEM command")
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm regression fixes from Dave Airlie:
"We interrupt your regularly scheduled drm fixes for a regression
special.
The first is for a fix in i915 that had unexpected side effects
fallout in the userspace X.org modesetting driver where X would no
longer start. I got tired of the nitpicking and issued a large hammer
on it. The X.org driver is buggy, but blackscreen regressions are
worse.
The second was an oversight that myself and Gerd should have noticed
better, Gerd is trying to fix this properly, but the regression is too
large to leave, even if the original behaviour is bad in some cases,
it's clearly bad to break a bunch of working use cases.
I'll likely have a regular fixes pull later, but I really wanted to
highlight these"
* tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/virtio: drop prime import/export callbacks"
Revert "drm/i915/fbdev: Actually configure untiled displays"
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes: 4acb20b462 ("net: socionext: different approach on DMA")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does more harm than good, as it breaks both Xwayland and
gnome-shell with X11.
Xwayland requires DRI3 & DRI3 requires PRIME.
X11 crash for obscure double-free reason which are hard to debug
(starting X11 by hand doesn't trigger the crash).
I don't see an apparent problem implementing those stub prime
functions, they may return an error at run-time, and it seems to be
handled fine by GNOME at least.
This reverts commit b318e3ff7c.
[airlied:
This broke userspace for virtio-gpus, and regressed things from DRI3 to DRI2.
This brings back the original problem, but it's better than regressions.]
Fixes: b318e3ff7c ("drm/virtio: drop prime import/export callbacks")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit d179b88deb.
This commit is documented to break userspace X.org modesetting driver in certain configurations.
The X.org modesetting userspace driver is broken. No fixes are available yet. In order for this patch to be applied it either needs a config option or a workaround developed.
This has been reported a few times, saying it's a userspace problem is clearly against the regression rules.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109806
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: <stable@vger.kernel.org> # v3.19+
Pull nfsd bugfixes from Bruce Fields:
"Fix miscellaneous nfsd bugs, in NFSv4.1 callbacks, NFSv4.1
lock-notification callbacks, NFSv3 readdir encoding, and the
cache/upcall code"
* tag 'nfsd-5.1-1' of git://linux-nfs.org/~bfields/linux:
nfsd: wake blocked file lock waiters before sending callback
nfsd: wake waiters blocked on file_lock before deleting it
nfsd: Don't release the callback slot unless it was actually held
nfsd/nfsd3_proc_readdir: fix buffer count and page pointers
sunrpc: don't mark uninitialised items as VALID.
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
It's possible for us to issue a lookup to revalidate a dentry
concurrently with a rename. If done in the right order, then we could
end up processing dentry info in the reply that no longer reflects the
state of the dentry.
If req->r_dentry->d_name differs from the one in the trace, then just
ignore the trace in the reply. We only need to do this however if the
parent's i_rwsem is not held.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Ben reported tripping the BUG_ON in create_request_message during some
performance testing. Analysis of the vmcore showed that the length of
the r_dentry->d_name string changed after we allocated the buffer, but
before we encoded it.
build_dentry_path returns pointers to d_name in the common case of
non-snapped dentries, but this optimization isn't safe unless the parent
directory is locked. When it isn't, have the code make a copy of the
d_name while holding the d_lock.
Cc: stable@vger.kernel.org
Reported-by: Ben England <bengland@redhat.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EFI stub is entered with the caches and MMU enabled by the
firmware, and once the stub is ready to hand over to the decompressor,
we clean and disable the caches.
The cache clean routines use CP15 barrier instructions, which can be
disabled via SCTLR. Normally, when using the provided cache handling
routines to enable the caches and MMU, this bit is enabled as well.
However, but since we entered the stub with the caches already enabled,
this routine is not executed before we call the cache clean routines,
resulting in undefined instruction exceptions if the firmware never
enabled this bit.
So set the bit explicitly in the EFI entry code, but do so in a way that
guarantees that the resulting code can still run on v6 cores as well
(which are guaranteed to have CP15 barriers enabled)
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When CONFIG_ARM_MPU is not defined, the base address of v7M SCB register
is not initialized with correct value. This prevents enabling I/D caches
when the L1 cache poilcy is applied in kernel.
Fixes: 3c24121039 ("ARM: 8756/1: NOMMU: Postpone MPU activation till __after_proc_init")
Signed-off-by: Tigran Tadevosyan <tigran.tadevosyan@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Naresh Kamboju recently reported that the function-graph tracer crashes
on ARM. The function-graph tracer assumes that the kernel is built with
frame pointers.
We explicitly disabled the function-graph tracer when building Thumb2,
since the Thumb2 ABI doesn't have frame pointers.
We recently changed the way the unwinder method was selected, which
seems to have made it more likely that we can end up with the function-
graph tracer enabled but without the kernel built with frame pointers.
Fix up the function graph tracer dependencies so the option is not
available when we have no possibility of having frame pointers, and
adjust the dependencies on the unwinder option to hide the non-frame
pointer unwinder options if the function-graph tracer is enabled.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Since commit 222b5f0441 ("drm/sched: Refactor ring mirror list
handling."), drm_sched_hw_job_reset is no longer there, so let's adjust
the doc comment accordingly.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since commit 09bb839434 we don't use the state argument for any sort
of on-stack caching in the io read and write path. Remove the stale
and unused argument from them, and bubble it up to __io_submit_sqe()
and down to io_prep_rw().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In order to make sure that the plane color space gets reset correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Initialize the flow input colorspaces to unknown and reset to that value
when the channel gets disabled. This avoids the state getting mixed up
with a previous mode.
Also keep the CSC settings for the background flow intact when disabling
the foreground flow.
Root-caused-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Another bodge for the ftrace PLT code: plt_entries_equal() now takes
the place relative nature of the ADRP/ADD based PLT entries into
account, which means that a struct trampoline instance on the stack
is no longer equal to the same set of opcodes in the module struct,
given that they don't point to the same place in memory anymore.
Work around this by using memcmp() in the ftrace PLT handling code.
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In the event that the start address of the initrd is not aligned, but
has an aligned size, the base + size will not cover the entire initrd
image and there is a chance that the kernel will corrupt the tail of the
image.
By aligning the end of the initrd to a page boundary and then
subtracting the adjusted start address the memblock reservation will
cover all pages that contains the initrd.
Fixes: c756c592e4 ("arm64: Utilize phys_initrd_start/phys_initrd_size")
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The tx_status poll in the rcar_dmac driver reads the status register
which indicates which chunk is busy (DMACHCRB). Afterwards the point
inside the chunk is read from DMATCRB. It is possible that the chunk
has changed between the two reads. The result is a non-monotonous
increase of the residue. Fix this by introducing a 'safe read' logic.
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit af19b7ce76 ("mmc: bcm2835: Avoid possible races on
data requests") introduces a possible circular locking dependency,
which is triggered by swapping to the sdhost interface.
So instead of reintroduce the race condition again, we could also
avoid this situation by using GFP_NOWAIT for the allocation of the
DMA buffer descriptors.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: af19b7ce76 ("mmc: bcm2835: Avoid possible races on data requests")
Link: http://lists.infradead.org/pipermail/linux-rpi-kernel/2019-March/008615.html
Signed-off-by: Vinod Koul <vkoul@kernel.org>
stmmac_check_ether_addr() checks the MAC address and assigns one in
driver open(). In many cases when we create slave netdevice, the dev
addr is inherited from master but the master dev addr maybe NULL at
that time, so move this call to driver probe so that address is
always valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Tested-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Sneh Shah <snehshah@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Add a selftest for icmp packet too big errors with conntrack, from
Florian Westphal.
2) Validate inner header in ICMP error message does not lie to us
in conntrack, also from Florian.
3) Initialize ct->timeout to calm down KASAN, from Alexander Potapenko.
4) Skip ICMP error messages from tunnels in IPVS, from Julian Anastasov.
5) Use a hash to expose conntrack and expectation ID, from Florian Westphal.
6) Prevent shift wrap in nft_chain_parse_hook(), from Dan Carpenter.
7) Fix broken ICMP ID randomization with NAT, also from Florian.
8) Remove WARN_ON in ebtables compat that is reached via syzkaller,
from Florian Westphal.
9) Fix broken timestamps since fb420d5d91 ("tcp/fq: move back to
CLOCK_MONOTONIC"), from Florian.
10) Fix logging of invalid packets in conntrack, from Andrei Vagin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a blocked NFS lock is "awoken" we send a callback to the server and
then wake any hosts waiting on it. If a client attempts to get a lock
and then drops off the net, we could end up waiting for a long time
until we end up waking locks blocked on that request.
So, wake any other waiting lock requests before sending the callback.
Do this by calling locks_delete_block in a new "prepare" phase for
CB_NOTIFY_LOCK callbacks.
URL: https://bugzilla.kernel.org/show_bug.cgi?id=203363
Fixes: 16306a61d3 ("fs/locks: always delete_block after waiting.")
Reported-by: Slawomir Pryczek <slawek1211@gmail.com>
Cc: Neil Brown <neilb@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
After a blocked nfsd file_lock request is deleted, knfsd will send a
callback to the client and then free the request. Commit 16306a61d3
("fs/locks: always delete_block after waiting.") changed it such that
locks_delete_block is always called on a request after it is awoken,
but that patch missed fixing up blocked nfsd request handling.
Call locks_delete_block on the block to wake up any locks still blocked
on the nfsd lock request before freeing it. Some of its callers already
do this however, so just remove those calls.
URL: https://bugzilla.kernel.org/show_bug.cgi?id=203363
Fixes: 16306a61d3 ("fs/locks: always delete_block after waiting.")
Reported-by: Slawomir Pryczek <slawek1211@gmail.com>
Cc: Neil Brown <neilb@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
io_uring_poll shouldn't signal EPOLLOUT | EPOLLWRNORM if the queue is
full; the old check would always signal EPOLLOUT | EPOLLWRNORM (unless
there were U32_MAX - 1 entries in the SQ queue).
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reading the SQ tail needs to come after setting IORING_SQ_NEED_WAKEUP in
flags; there is no cheap barrier for ordering a store before a load, a
full memory barrier is required.
Userspace needs a full memory barrier between updating SQ tail and
checking for the IORING_SQ_NEED_WAKEUP too.
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A read memory barrier is required between reading SQ tail and reading
the actual data belonging to the SQ entry.
Userspace needs a matching write barrier between writing SQ entries and
updating SQ tail (using smp_store_release to update tail will do).
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we have multiple threads doing io_uring_register(2) on an io_uring
fd, then we can potentially try and kill the percpu reference while
someone else has already killed it.
Prevent this race by failing io_uring_register(2) if the ref is marked
dying. This is safe since we're inside the io_uring mutex.
Fixes: b19062a567 ("io_uring: fix possible deadlock between io_uring_{enter,register}")
Reported-by: syzbot <syzbot+10d25e23199614b7721f@syzkaller.appspotmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It doesn't log a packet if sysctl_log_invalid isn't equal to protonum
OR sysctl_log_invalid isn't equal to IPPROTO_RAW. This sentence is
always true. I believe we need to replace OR to AND.
Cc: Florian Westphal <fw@strlen.de>
Fixes: c4f3db1595 ("netfilter: conntrack: add and use nf_l4proto_log_invalid")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
setting net.netfilter.nf_conntrack_timestamp=1 breaks xmit with fq
scheduler. skb->tstamp might be "refreshed" using ktime_get_real(),
but fq expects CLOCK_MONOTONIC.
This patch removes all places in netfilter that check/set skb->tstamp:
1. To fix the bogus "start" time seen with conntrack timestamping for
outgoing packets, never use skb->tstamp and always use current time.
2. In nfqueue and nflog, only use skb->tstamp for incoming packets,
as determined by current hook (prerouting, input, forward).
3. xt_time has to use system clock as well rather than skb->tstamp.
We could still use skb->tstamp for prerouting/input/foward, but
I see no advantage to make this conditional.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Cc: Eric Dumazet <edumazet@google.com>
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONFIG_DECNET_ROUTE_FWMARK was removed in commit 47dcf0cb10 ("[NET]: Rethink mark field in struct flowi")
Since nothing replace it (and nothindg need to replace it, simply remove
it from documentation.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working on the Allwinner internal PHY, the first work was to use
the "internal" mode, but some answer was made my mail on what are really
internal mean for PHY.
This patch write that in the doc.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device refuses the offload in tls_set_device_offload_rx()
it calls tls_sw_free_resources_rx() to clean up software context
state.
Unfortunately, tls_sw_free_resources_rx() does not free all
the state tls_set_sw_offload() allocated - it leaks IV and
sequence number buffers. All other code paths which lead to
tls_sw_release_resources_rx() (which tls_sw_free_resources_rx()
calls) free those right before the call.
Avoid the leak by moving freeing of iv and rec_seq into
tls_sw_release_resources_rx().
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device supports offload, but offload fails tls_set_device_offload_rx()
will call tls_sw_free_resources_rx() which (unhelpfully) releases
and reacquires the socket lock.
For a small fix release and reacquire the device_offload_lock.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The run_afpackettests will be marked as passed regardless the return
value of those sub-tests in the script:
--------------------
running psock_tpacket test
--------------------
[FAIL]
selftests: run_afpackettests [PASS]
Fix this by changing the return value for each tests.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull NFS client bugfix from Trond Myklebust:
"Fix a regression in which an RPC call can be tagged with an error
despite the transmission being successful"
* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Ignore queue transmission errors on successful transmission
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
Pull block fixes from Jens Axboe:
"A set of small fixes that should go into this series. This contains:
- Removal of unused queue member (Hou)
- Overflow bvec fix (Ming)
- Various little io_uring tweaks (me)
- kthread parking
- Only call cpu_possible() for verified CPU
- Drop unused 'file' argument to io_file_put()
- io_uring_enter vs io_uring_register deadlock fix
- CQ overflow fix
- BFQ internal depth update fix (me)"
* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
io_uring: fix CQ overflow condition
io_uring: fix possible deadlock between io_uring_{enter,register}
io_uring: drop io_file_put() 'file' argument
bfq: update internal depth state when queue depth changes
io_uring: only test SQPOLL cpu after we've verified it
io_uring: park SQPOLL thread if it's percpu
Pill i3c fixes from Boris Brezillon:
- fix the random PID check
- fix the disable controller logic in the designware driver
- fix I3C entry in MAINTAINERS
* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: Fix the I3C entry
i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
i3c: Fix the verification of random PID
Pull sound fixes from Takashi Iwai:
"Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer.
The rest are usual small HD-audio fixes"
* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - add two more pin configuration sets to quirk table
ALSA: core: Fix card races between register and disconnect
ALSA: info: Fix racy addition/deletion of nodes
ALSA: hda: Initialize power_state field properly
Pull perf fixes from Ingo Molnar:
"Misc fixes:
- various tooling fixes
- kretprobe fixes
- kprobes annotation fixes
- kprobes error checking fix
- fix the default events for AMD Family 17h CPUs
- PEBS fix
- AUX record fix
- address filtering fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Avoid kretprobe recursion bug
kprobes: Mark ftrace mcount handler functions nokprobe
x86/kprobes: Verify stack frame on kretprobe
perf/x86/amd: Add event map for AMD Family 17h
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
perf tools: Fix map reference counting
perf evlist: Fix side band thread draining
perf tools: Check maps for bpf programs
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
tools include uapi: Sync sound/asound.h copy
perf top: Always sample time to satisfy needs of use of ordered queuing
perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
tools lib traceevent: Fix missing equality check for strcmp
perf stat: Disable DIR_FORMAT feature for 'perf stat record'
perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
perf header: Fix lock/unlock imbalances when processing BPF/BTF info
perf/x86: Fix incorrect PEBS_REGS
perf/ring_buffer: Fix AUX record suppression
perf/core: Fix the address filtering fix
kprobes: Fix error check when reusing optimized probes
Pull x86 fixes from Ingo Molnar:
"Misc fixes all over the place: a console spam fix, section attributes
fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
quirk, boot options related warnings fix, an LTO fix, a deadlock fix
and an RDT fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
x86/cpu/bugs: Use __initconst for 'const' init data
x86/mm/KASLR: Fix the size of the direct mapping section
x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
x86/mm: Prevent bogus warnings with "noexec=off"
x86/build/lto: Fix truncated .bss with -fdata-sections
x86/speculation: Prevent deadlock on ssb_state::lock
x86/resctrl: Do not repeat rdtgroup mode initialization
Pull scheduler fixes from Ingo Molnar:
"A deadline scheduler warning/race fix, and a cfs_period_us quota
calculation workaround where the real fix looks too involved to merge
immediately"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Correctly handle active 0-lag timers
sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup
Pull locking fixes from Ingo Molnar:
"A lockdep warning fix and a script execution fix when atomics are
generated"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomics: Don't assume that scripts are executable
locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again
Pull cgroup fix from Tejun Heo:
"A patch to fix a RCU imbalance error in the devices cgroup
configuration error path"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU imbalance in error case
Pull percpu fixlet from Dennis Zhou:
"This stops printing the base address of percpu memory on
initialization"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu: stop printing kernel addresses
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-19
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.7:
('net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query')
For -stable v4.19:
('net/mlx5e: Fix the max MTU check in case of XDP')
For -stable v5.0:
('net/mlx5e: Fix use-after-free after xdp_return_frame')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we add a bond device which is already the master of the team interface,
we will hold the team->lock in team_add_slave() first and then request the
lock in team_set_mac_address() again. The functions are called like:
- team_add_slave()
- team_port_add()
- team_port_enter()
- team_modeop_port_enter()
- __set_port_dev_addr()
- dev_set_mac_address()
- bond_set_mac_address()
- dev_set_mac_address()
- team_set_mac_address
Although team_upper_dev_link() would check the upper devices but it is
called too late. Fix it by adding a checking before processing the slave.
v2: Do not split the string in netdev_err()
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The run_netsocktests will be marked as passed regardless the actual test
result from the ./socket:
selftests: net: run_netsocktests
========================================
--------------------
running socket test
--------------------
[FAIL]
ok 1..6 selftests: net: run_netsocktests [PASS]
This is because the test script itself has been successfully executed.
Fix this by exit 1 when the test failed.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Querying EEPROM high pages data for SFP module is currently
not supported by our driver and yet queried, resulting in
invalid FW queries.
Set the EEPROM ethtool data length to 256 for SFP module will
limit the reading for page 0 only and prevent invalid FW queries.
Fixes: bb64143eee ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5E_XDP_MAX_MTU was calculated incorrectly. It didn't account for
NET_IP_ALIGN and MLX5E_HW2SW_MTU, and it also misused MLX5_SKB_FRAG_SZ.
This commit fixes the calculations and adds a brief explanation for the
formula used.
Fixes: a26a5bdf3e ("net/mlx5e: Restrict the combination of large MTU and XDP")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
xdp_return_frame releases the frame. It leads to releasing the page, so
it's not allowed to access xdpi.xdpf->len after that, because xdpi.xdpf
is at xdp->data_hard_start after convert_to_xdp_frame. This patch moves
the memory access to precede the return of the frame.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull tty/serial fixes from Greg KH:
"Here are five small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1,
and resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the
previous patch to try to solve the issue. It has not shown up in
linux-next yet, unlike all of the other patches, but it has passed
0-day testing and everyone seems to agree that it is correct"
* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: put err_spi and err_i2c into correct #ifdef
vt: fix cursor when clearing the screen
sc16is7xx: move label 'err_spi' to correct section
serial: sh-sci: Fix HSCIF RX sampling point adjustment
serial: sh-sci: Fix HSCIF RX sampling point calculation
I've discovered following discrepancy in the bindings/net/ethernet.txt
documentation, where it states following:
- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
- nvmem-cell-names: string, should be "mac-address" if nvmem is to be..
which is actually misleading and confusing. There are only two ethernet
drivers in the tree, cadence/macb and davinci which supports this
properties.
This nvmem-cell* properties were introduced in commit 9217e566bd
("of_net: Implement of_get_nvmem_mac_address helper"), but
commit afa64a72b8 ("of: net: kill of_get_nvmem_mac_address()")
forget to properly clean up this parts.
So this patch fixes the documentation by moving the nvmem-cell*
properties at the appropriate places. While at it, I've removed unused
include as well.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fixes: afa64a72b8 ("of: net: kill of_get_nvmem_mac_address()")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
Pull staging and IIO fixes from Greg KH:
"Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next
for a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
staging: erofs: fix unexpected out-of-bound data access
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
staging: most: core: use device description as name
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
...
Pull char/misc fixes from Greg KH:
"Here are four small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and two tiny bugfixes.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
extcon: ptn5150: fix COMPILE_TEST dependencies
misc: fastrpc: add checked value for dma_set_mask
habanalabs: remove low credit limit of DMA #0
bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.
So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.
This patch fixes this issue reported by Zhang Yi When running nvme/011.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 6dc4f100c1 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull input updates from Dmitry Torokhov:
- several new key mappings for HID
- a host of new ACPI IDs used to identify Elan touchpads in Lenovo
laptops
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
HID: input: add mapping for "Toggle Display" key
HID: input: add mapping for "Full Screen" key
HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
HID: input: add mapping for Expose/Overview key
HID: input: fix mapping of aspect ratio key
[media] doc-rst: switch to new names for Full Screen/Aspect keys
Input: document meanings of KEY_SCREEN and KEY_ZOOM
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes: 86039bd3b4 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted
5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Guenter Roeck <groeck@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During !CONFIG_CGROUP reclaim, we expand the inactive list size if it's
thrashing on the node that is about to be reclaimed. But when cgroups
are enabled, we suddenly ignore the node scope and use the cgroup scope
only. The result is that pressure bleeds between NUMA nodes depending
on whether cgroups are merely compiled into Linux. This behavioral
difference is unexpected and undesirable.
When the refault adaptivity of the inactive list was first introduced,
there were no statistics at the lruvec level - the intersection of node
and memcg - so it was better than nothing.
But now that we have that infrastructure, use lruvec_page_state() to
make the list balancing decision always NUMA aware.
[hannes@cmpxchg.org: fix bisection hole]
Link: http://lkml.kernel.org/r/20190417155241.GB23013@cmpxchg.org
Link: http://lkml.kernel.org/r/20190412144438.2645-1-hannes@cmpxchg.org
Fixes: 2a2e48854d ("mm: vmscan: fix IO/refault regression in cache workingset transition")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
has_unmovable_pages() is used by allocating CMA and gigantic pages as
well as the memory hotplug. The later doesn't know how to offline CMA
pool properly now, but if an unused (free) CMA page is encountered, then
has_unmovable_pages() happily considers it as a free memory and
propagates this up the call chain. Memory offlining code then frees the
page without a proper CMA tear down which leads to an accounting issues.
Moreover if the same memory range is onlined again then the memory never
gets back to the CMA pool.
State after memory offline:
# grep cma /proc/vmstat
nr_free_cma 205824
# cat /sys/kernel/debug/cma/cma-kvm_cma/count
209920
Also, kmemleak still think those memory address are reserved below but
have already been used by the buddy allocator after onlining. This
patch fixes the situation by treating CMA pageblocks as unmovable except
when has_unmovable_pages() is called as part of CMA allocation.
Offlined Pages 4096
kmemleak: Cannot insert 0xc000201f7d040008 into the object search tree (overlaps existing)
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
create_object+0x344/0x380
__kmalloc_node+0x3ec/0x860
kvmalloc_node+0x58/0x110
seq_read+0x41c/0x620
__vfs_read+0x3c/0x70
vfs_read+0xbc/0x1a0
ksys_read+0x7c/0x140
system_call+0x5c/0x70
kmemleak: Kernel memory leak detector disabled
kmemleak: Object 0xc000201cc8000000 (size 13757317120):
kmemleak: comm "swapper/0", pid 0, jiffies 4294937297
kmemleak: min_count = -1
kmemleak: count = 0
kmemleak: flags = 0x5
kmemleak: checksum = 0
kmemleak: backtrace:
cma_declare_contiguous+0x2a4/0x3b0
kvm_cma_reserve+0x11c/0x134
setup_arch+0x300/0x3f8
start_kernel+0x9c/0x6e8
start_here_common+0x1c/0x4b0
kmemleak: Automatic memory scanning thread ended
[cai@lca.pw: use is_migrate_cma_page() and update commit log]
Link: http://lkml.kernel.org/r/20190416170510.20048-1-cai@lca.pw
Link: http://lkml.kernel.org/r/20190413002623.8967-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The igrab() in shmem_unuse() looks good, but we forgot that it gives no
protection against concurrent unmounting: a point made by Konstantin
Khlebnikov eight years ago, and then fixed in 2.6.39 by 778dd893ae
("tmpfs: fix race between umount and swapoff"). The current 5.1-rc
swapoff is liable to hit "VFS: Busy inodes after unmount of tmpfs.
Self-destruct in 5 seconds. Have a nice day..." followed by GPF.
Once again, give up on using igrab(); but don't go back to making such
heavy-handed use of shmem_swaplist_mutex as last time: that would spoil
the new design, and I expect could deadlock inside shmem_swapin_page().
Instead, shmem_unuse() just raise a "stop_eviction" count in the shmem-
specific inode, and shmem_evict_inode() wait for that to go down to 0.
Call it "stop_eviction" rather than "swapoff_busy" because it can be put
to use for others later (huge tmpfs patches expect to use it).
That simplifies shmem_unuse(), protecting it from both unlink and
unmount; and in practice lets it locate all the swap in its first try.
But do not rely on that: there's still a theoretical case, when
shmem_writepage() might have been preempted after its get_swap_page(),
before making the swap entry visible to swapoff.
[hughd@google.com: remove incorrect list_del()]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904091133570.1898@eggly.anvils
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081259400.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SWAP_UNUSE_MAX_TRIES 3 appeared to work well in earlier testing, but
further testing has proved it to be a source of unnecessary swapoff
EBUSY failures (which can then be followed by unmount EBUSY failures).
When mmget_not_zero() or shmem's igrab() fails, there is an mm exiting
or inode being evicted, freeing up swap independent of try_to_unuse().
Those typically completed much sooner than the old quadratic swapoff,
but now it's more common that swapoff may need to wait for them.
It's possible to move those cases from init_mm.mmlist and shmem_swaplist
to separate "exiting" swaplists, and try_to_unuse() then wait for those
lists to be emptied; but we've not bothered with that in the past, and
don't want to risk missing some other forgotten case. So just revert to
cycling around until the swap is gone, without any retries limit.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081256170.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 51dedad06b ("kasan, slab: make freelist stored without tags")
calls kasan_reset_tag() for off-slab slab management object leading to
freelist being stored non-tagged.
However, cache_grow_begin() calls alloc_slabmgmt() which calls
kmem_cache_alloc_node() assigns a tag for the address and stores it in
the shadow address. As the result, it causes endless errors below
during boot due to drain_freelist() -> slab_destroy() ->
kasan_slab_free() which compares already untagged freelist against the
stored tag in the shadow address.
Since off-slab slab management object freelist is such a special case,
just store it tagged. Non-off-slab management object freelist is still
stored untagged which has not been assigned a tag and should not cause
any other troubles with this inconsistency.
BUG: KASAN: double-free or invalid-free in slab_destroy+0x84/0x88
Pointer tag: [ff], memory tag: [99]
CPU: 0 PID: 1376 Comm: kworker/0:4 Tainted: G W 5.1.0-rc3+ #8
Hardware name: HPE Apollo 70 /C01_APACHE_MB , BIOS L50_5.13_1.0.6 07/10/2018
Workqueue: cgroup_destroy css_killed_work_fn
Call trace:
print_address_description+0x74/0x2a4
kasan_report_invalid_free+0x80/0xc0
__kasan_slab_free+0x204/0x208
kasan_slab_free+0xc/0x18
kmem_cache_free+0xe4/0x254
slab_destroy+0x84/0x88
drain_freelist+0xd0/0x104
__kmem_cache_shrink+0x1ac/0x224
__kmemcg_cache_deactivate+0x1c/0x28
memcg_deactivate_kmem_caches+0xa0/0xe8
memcg_offline_kmem+0x8c/0x3d4
mem_cgroup_css_offline+0x24c/0x290
css_killed_work_fn+0x154/0x618
process_one_work+0x9cc/0x183c
worker_thread+0x9b0/0xe38
kthread+0x374/0x390
ret_from_fork+0x10/0x18
Allocated by task 1625:
__kasan_kmalloc+0x168/0x240
kasan_slab_alloc+0x18/0x20
kmem_cache_alloc_node+0x1f8/0x3a0
cache_grow_begin+0x4fc/0xa24
cache_alloc_refill+0x2f8/0x3e8
kmem_cache_alloc+0x1bc/0x3bc
sock_alloc_inode+0x58/0x334
alloc_inode+0xb8/0x164
new_inode_pseudo+0x20/0xec
sock_alloc+0x74/0x284
__sock_create+0xb0/0x58c
sock_create+0x98/0xb8
__sys_socket+0x60/0x138
__arm64_sys_socket+0xa4/0x110
el0_svc_handler+0x2c0/0x47c
el0_svc+0x8/0xc
Freed by task 1625:
__kasan_slab_free+0x114/0x208
kasan_slab_free+0xc/0x18
kfree+0x1a8/0x1e0
single_release+0x7c/0x9c
close_pdeo+0x13c/0x43c
proc_reg_release+0xec/0x108
__fput+0x2f8/0x784
____fput+0x1c/0x28
task_work_run+0xc0/0x1b0
do_notify_resume+0xb44/0x1278
work_pending+0x8/0x10
The buggy address belongs to the object at ffff809681b89e00
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 0 bytes inside of
128-byte region [ffff809681b89e00, ffff809681b89e80)
The buggy address belongs to the page:
page:ffff7fe025a06e00 count:1 mapcount:0 mapping:01ff80082000fb00
index:0xffff809681b8fe04
flags: 0x17ffffffc000200(slab)
raw: 017ffffffc000200 ffff7fe025a06d08 ffff7fe022ef7b88 01ff80082000fb00
raw: ffff809681b8fe04 ffff809681b80000 00000001000000e0 0000000000000000
page dumped because: kasan: bad access detected
page allocated via order 0, migratetype Unmovable, gfp_mask
0x2420c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_COMP|__GFP_THISNODE)
prep_new_page+0x4e0/0x5e0
get_page_from_freelist+0x4ce8/0x50d4
__alloc_pages_nodemask+0x738/0x38b8
cache_grow_begin+0xd8/0xa24
____cache_alloc_node+0x14c/0x268
__kmalloc+0x1c8/0x3fc
ftrace_free_mem+0x408/0x1284
ftrace_free_init_mem+0x20/0x28
kernel_init+0x24/0x548
ret_from_fork+0x10/0x18
Memory state around the buggy address:
ffff809681b89c00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
ffff809681b89d00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
>ffff809681b89e00: 99 99 99 99 99 99 99 99 fe fe fe fe fe fe fe fe
^
ffff809681b89f00: 43 43 43 43 43 fe fe fe fe fe fe fe fe fe fe fe
ffff809681b8a000: 6d fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
Link: http://lkml.kernel.org/r/20190403022858.97584-1-cai@lca.pw
Fixes: 51dedad06b ("kasan, slab: make freelist stored without tags")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a driver unloads without unloading TTM we don't correctly
clear the global structures leading to errors on re-init.
Next step should probably be to remove the global structures and
kobjs all together, but this is tricky since we need to maintain
backward compatibility.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
CC: stable@vger.kernel.org # 5.0.x
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid kretprobe recursion loop bg by setting a dummy
kprobes to current_kprobe per-CPU variable.
This bug has been introduced with the asm-coded trampoline
code, since previously it used another kprobe for hooking
the function return placeholder (which only has a nop) and
trampoline handler was called from that kprobe.
This revives the old lost kprobe again.
With this fix, we don't see deadlock anymore.
And you can see that all inner-called kretprobe are skipped.
event_1 235 0
event_2 19375 19612
The 1st column is recorded count and the 2nd is missed count.
Above shows (event_1 rec) + (event_2 rec) ~= (event_2 missed)
(some difference are here because the counter is racy)
Reported-by: Andrea Righi <righi.andrea@gmail.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: c9becf58d9 ("[PATCH] kretprobe: kretprobe-booster")
Link: http://lkml.kernel.org/r/155094064889.6137.972160690963039.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of relying on the now removed NULL argument to
pci_alloc_consistent, switch to the generic DMA API, and store the struct
device so that we can pass it.
Fixes: 4167b2ad51 ("PCI: Remove NULL device handling from PCI DMA API")
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch clears FC_RP_STARTED flag during logoff, because of this
re-login(flogi) didn't happen to the switch.
This reverts commit 1550ec458e.
Fixes: 1550ec458e ("scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@#suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike atomic_add(), refcount_add() does not deal well
with a negative argument. TLS fallback code reallocates
the skb and is very likely to shrink the truesize, leading to:
[ 189.513254] WARNING: CPU: 5 PID: 0 at lib/refcount.c:81 refcount_add_not_zero_checked+0x15c/0x180
Call Trace:
refcount_add_checked+0x6/0x40
tls_enc_skb+0xb93/0x13e0 [tls]
Once wmem_allocated count saturates the application can no longer
send data on the socket. This is similar to Eric's fixes for GSO,
TCP:
commit 7ec318feee ("tcp: gso: avoid refcount_t warning from tcp_gso_segment()")
and UDP:
commit 575b65bc5b ("udp: avoid refcount_t saturation in __udp_gso_segment()").
Unlike the GSO case, for TLS fallback it's likely that the skb has
shrunk, so the "likely" annotation is the other way around (likely
branch being "sub").
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. The IOT2020 is identified by its unique
asset tag. Match on it first. If we then match on the board name only,
we will catch all IOT2040 variants. In the future there will be no other
devices with the "SIMATIC IOT2000" DMI board name but different
hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Few small fixes
Patch #1, from Petr, adjusts mlxsw to provide the same QoS behavior for
both Spectrum-1 and Spectrum-2. The fix is required due to a difference
in the behavior of Spectrum-2 compared to Spectrum-1. The problem and
solution are described in the detail in the changelog.
Patch #2 increases the time period in which the driver waits for the
firmware to signal it has finished its initialization. The issue will be
fixed in future firmware versions and the timeout will be decreased.
Patch #3, from Amit, fixes a display problem where the autoneg status in
ethtool is not updated in case the netdev is not running.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull arm64 fix from Catalin Marinas:
"Avoid compiler uninitialised warning introduced by recent arm64 futex
fix"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: futex: Restore oldval initialization to work around buggy compilers
Commit 045afc2412 ("arm64: futex: Fix FUTEX_WAKE_OP atomic ops with
non-zero result value") removed oldval's zero initialization in
arch_futex_atomic_op_inuser because it is not necessary. Unfortunately,
Android's arm64 GCC 4.9.4 [1] does not agree:
../kernel/futex.c: In function 'do_futex':
../kernel/futex.c:1658:17: warning: 'oldval' may be used uninitialized
in this function [-Wmaybe-uninitialized]
return oldval == cmparg;
^
In file included from ../kernel/futex.c:73:0:
../arch/arm64/include/asm/futex.h:53:6: note: 'oldval' was declared here
int oldval, ret, tmp;
^
GCC fails to follow that when ret is non-zero, futex_atomic_op_inuser
returns right away, avoiding the uninitialized use that it claims.
Restoring the zero initialization works around this issue.
[1]: https://android.googlesource.com/platform/prebuilts/gcc/linux-x86/aarch64/aarch64-linux-android-4.9/
Cc: stable@vger.kernel.org
Fixes: 045afc2412 ("arm64: futex: Fix FUTEX_WAKE_OP atomic ops with non-zero result value")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As stated in the original commit for pidfd_send_signal() we don't allow
to signal processes through O_PATH file descriptors since it is
semantically equivalent to a write on the pidfd.
We already correctly error out right now and return EBADF if an O_PATH
fd is passed. This is because we use file->f_op to detect whether a
pidfd is passed and O_PATH fds have their file->f_op set to empty_fops
in do_dentry_open() and thus fail the test.
Thus, there is no regression. It's just semantically correct to use
fdget() and return an error right from there instead of taking a
reference and returning an error later.
Signed-off-by: Christian Brauner <christian@brauner.io>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jann Horn <jann@thejh.net>
Cc: David Howells <dhowells@redhat.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull s390 bug fixes from Martin Schwidefsky:
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
* tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct some inline assembly constraints
s390/pkey: add one more argument space for debug feature entry
s390/zcrypt: fix possible deadlock situation on ap queue remove
s390/3270: fix lockdep false positive on view->lock
s390/dasd: Fix capacity calculation for large volumes
s390/mem_detect: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD)
Pull AFS fixes from David Howells:
- Stop using the deprecated get_seconds().
- Don't make tracepoint strings const as the section they go in isn't
read-only.
- Differentiate failure due to unmarshalling from other failure cases.
We shouldn't abort with RXGEN_CC/SS_UNMARSHAL if it's not due to
unmarshalling.
- Add a missing unlock_page().
- Fix the interaction between receiving a notification from a server
that it has invalidated all outstanding callback promises and a
client call that we're in the middle of making that will get a new
promise.
* tag 'afs-fixes-20190413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix in-progess ops to ignore server-level callback invalidation
afs: Unlock pages for __pagevec_release()
afs: Differentiate abort due to unmarshalling from other errors
afs: Avoid section confusion in CM_NAME
afs: avoid deprecated get_seconds()
Pull crypto fix from Herbert Xu:
"Fix a bug in the implementation of the x86 accelerated version of
poly1305"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/poly1305 - fix overflow during partial reduction
Pull drm fixes from Dave Airlie:
"Since Easter is looming for me, I'm just pushing whatever is in my
tree, I'll see what else turns up and maybe I'll send another pull
early next week if there is anything.
tegra:
- stream id programming fix
- avoid divide by 0 for bad hdmi audio setup code
ttm:
- Hugepages fix
- refcount imbalance in error path fix
amdgpu:
- GPU VM fixes for Vega/RV
- DC AUX fix for active DP-DVI dongles
- DC fix for multihead regression"
* tag 'drm-fixes-2019-04-18' of git://anongit.freedesktop.org/drm/drm:
drm/tegra: hdmi: Setup audio only if configured
drm/amd/display: If one stream full updates, full update all planes
drm/amdgpu/gmc9: fix VM_L2_CNTL3 programming
drm/amdgpu: shadow in shadow_list without tbo.mem.start cause page fault in sriov TDR
gpu: host1x: Program stream ID to bypass without SMMU
drm/amd/display: extending AUX SW Timeout
drm/ttm: fix dma_fence refcount imbalance on error path
drm/ttm: fix incrementing the page pointer for huge pages
drm/ttm: fix start page for huge page check in ttm_put_pages()
drm/ttm: fix out-of-bounds read in ttm_put_pages() v2
tick_freeze() introduced by suspend-to-idle in commit 124cf9117c ("PM /
sleep: Make it possible to quiesce timers during suspend-to-idle") uses
timekeeping_suspend() instead of syscore_suspend() during
suspend-to-idle. As a consequence generic sched_clock will keep going
because sched_clock_suspend() and sched_clock_resume() are not invoked
during suspend-to-idle which can result in a generic sched_clock wrap.
On a ARM system with suspend-to-idle enabled, sched_clock is registered
as "56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns", which
means the real wrapping duration is 8796093022202ns.
[ 134.551779] suspend-to-idle suspend (timekeeping_suspend())
[ 1204.912239] suspend-to-idle resume (timekeeping_resume())
......
[ 1206.912239] suspend-to-idle suspend (timekeeping_suspend())
[ 5880.502807] suspend-to-idle resume (timekeeping_resume())
......
[ 6000.403724] suspend-to-idle suspend (timekeeping_suspend())
[ 8035.753167] suspend-to-idle resume (timekeeping_resume())
......
[ 8795.786684] (2)[321:charger_thread]......
[ 8795.788387] (2)[321:charger_thread]......
[ 0.057226] (0)[0:swapper/0]......
[ 0.061447] (2)[0:swapper/2]......
sched_clock was not stopped during suspend-to-idle, and sched_clock_poll
hrtimer was not expired because timekeeping_suspend() was invoked during
suspend-to-idle. It makes sched_clock wrap at kernel time 8796s.
To prevent this, invoke sched_clock_suspend() and sched_clock_resume() in
tick_freeze() together with timekeeping_suspend() and timekeeping_resume().
Fixes: 124cf9117c (PM / sleep: Make it possible to quiesce timers during suspend-to-idle)
Signed-off-by: Chang-An Chen <chang-an.chen@mediatek.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Corey Minyard <cminyard@mvista.com>
Cc: <linux-mediatek@lists.infradead.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: <kuohong.wang@mediatek.com>
Cc: <freddy.hsin@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1553828349-8914-1-git-send-email-chang-an.chen@mediatek.com
kernel_randomize_memory() uses __PHYSICAL_MASK_SHIFT to calculate
the maximum amount of system RAM supported. The size of the direct
mapping section is obtained from the smaller one of the below two
values:
(actual system RAM size + padding size) vs (max system RAM size supported)
This calculation is wrong since commit
b83ce5ee91 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52").
In it, __PHYSICAL_MASK_SHIFT was changed to be 52, regardless of whether
the kernel is using 4-level or 5-level page tables. Thus, it will always
use 4 PB as the maximum amount of system RAM, even in 4-level paging
mode where it should actually be 64 TB.
Thus, the size of the direct mapping section will always
be the sum of the actual system RAM size plus the padding size.
Even when the amount of system RAM is 64 TB, the following layout will
still be used. Obviously KALSR will be weakened significantly.
|____|_______actual RAM_______|_padding_|______the rest_______|
0 64TB ~120TB
Instead, it should be like this:
|____|_______actual RAM_______|_________the rest______________|
0 64TB ~120TB
The size of padding region is controlled by
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING, which is 10 TB by default.
The above issue only exists when
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING is set to a non-zero value,
which is the case when CONFIG_MEMORY_HOTPLUG is enabled. Otherwise,
using __PHYSICAL_MASK_SHIFT doesn't affect KASLR.
Fix it by replacing __PHYSICAL_MASK_SHIFT with MAX_PHYSMEM_BITS.
[ bp: Massage commit message. ]
Fixes: b83ce5ee91 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52")
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: frank.ramsay@hpe.com
Cc: herbert@gondor.apana.org.au
Cc: kirill@shutemov.name
Cc: mike.travis@hpe.com
Cc: thgarnie@google.com
Cc: x86-ml <x86@kernel.org>
Cc: yamada.masahiro@socionext.com
Link: https://lkml.kernel.org/r/20190417083536.GE7065@MiWiFi-R3L-srv
clang points out that the return code from this function is
undefined for one of the error paths:
../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here
return result;
^~~~~~
../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning
int result;
^
Make it return -ENODEV here, as in the related failure cases.
gcc has a known bug in underreporting some of these warnings
when it has already eliminated the assignment of the return code
based on some earlier optimization step.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e636141 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When scatter to CQE is enabled on a DCT QP it corrupts the mailbox command
since it tried to treat it as as QP create mailbox command instead of a
DCT create command.
The corrupted mailbox command causes userspace to malfunction as the
device doesn't create the QP as expected.
A new mlx5 capability is exposed to user-space which ensures that it will
not enable the feature on DCT without this fix in the kernel.
Fixes: 5d6ff1babe ("IB/mlx5: Support scatter to CQE for DC transport type")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pull smb3 fixes from Steve French:
"Five small SMB3 fixes, all also for stable - an important fix for an
oplock (lease) bug, a handle leak, and three bugs spotted by KASAN"
* tag '5.1-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: keep FileInfo handle live during oplock break
cifs: fix handle leak in smb2_query_symlink()
cifs: Fix lease buffer length error
cifs: Fix use-after-free in SMB2_read
cifs: Fix use-after-free in SMB2_write
If a request transmission fails due to write space or slot unavailability
errors, but the queued task then gets transmitted before it has time to
process the error in call_transmit_status() or call_bc_transmit_status(),
we need to suppress the transmission error code to prevent it from leaking
out of the RPC layer.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
This is a leftover from when the rings initially were not free flowing,
and hence a test for tail + 1 == head would indicate full. Since we now
let them wrap instead of mask them with the size, we need to check if
they drift more than the ring size from each other.
This fixes a case where we'd overwrite CQ ring entries, if the user
failed to reap completions. Both cases would ultimately result in lost
completions as the application violated the depth it asked for. The only
difference is that before this fix we'd return invalid entries for the
overflowed completions, instead of properly flagging it in the
cq_ring->overflow variable.
Reported-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By calling maps__insert() we assume to get 2 references on the map,
which we relese within maps__remove call.
However if there's already same map name, we currently don't bump the
reference and can crash, like:
Program received signal SIGABRT, Aborted.
0x00007ffff75e60f5 in raise () from /lib64/libc.so.6
(gdb) bt
#0 0x00007ffff75e60f5 in raise () from /lib64/libc.so.6
#1 0x00007ffff75d0895 in abort () from /lib64/libc.so.6
#2 0x00007ffff75d0769 in __assert_fail_base.cold () from /lib64/libc.so.6
#3 0x00007ffff75de596 in __assert_fail () from /lib64/libc.so.6
#4 0x00000000004fc006 in refcount_sub_and_test (i=1, r=0x1224e88) at tools/include/linux/refcount.h:131
#5 refcount_dec_and_test (r=0x1224e88) at tools/include/linux/refcount.h:148
#6 map__put (map=0x1224df0) at util/map.c:299
#7 0x00000000004fdb95 in __maps__remove (map=0x1224df0, maps=0xb17d80) at util/map.c:953
#8 maps__remove (maps=0xb17d80, map=0x1224df0) at util/map.c:959
#9 0x00000000004f7d8a in map_groups__remove (map=<optimized out>, mg=<optimized out>) at util/map_groups.h:65
#10 machine__process_ksymbol_unregister (sample=<optimized out>, event=0x7ffff7279670, machine=<optimized out>) at util/machine.c:728
#11 machine__process_ksymbol (machine=<optimized out>, event=0x7ffff7279670, sample=<optimized out>) at util/machine.c:741
#12 0x00000000004fffbb in perf_session__deliver_event (session=0xb11390, event=0x7ffff7279670, tool=0x7fffffffc7b0, file_offset=13936) at util/session.c:1362
#13 0x00000000005039bb in do_flush (show_progress=false, oe=0xb17e80) at util/ordered-events.c:243
#14 __ordered_events__flush (oe=0xb17e80, how=OE_FLUSH__ROUND, timestamp=<optimized out>) at util/ordered-events.c:322
#15 0x00000000005005e4 in perf_session__process_user_event (session=session@entry=0xb11390, event=event@entry=0x7ffff72a4af8,
...
Add the map to the list and getting the reference event if we find the
map with same name.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Fixes: 1e6285699b ("perf symbols: Fix slowness due to -ffunction-section")
Link: http://lkml.kernel.org/r/20190416160127.30203-10-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull IPMI fixes from Corey Minyard:
"Fixes for some bugs cause by recent changes. One crash if you feed bad
data to the module parameters, one BUG that sometimes occurs when a
user closes the connection, and one bug that cause the driver to not
work if the configuration information only comes in from SMBIOS"
* tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi:
ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
ipmi: Fix failure on SMBIOS specified devices
Pull networking fixes from David Miller:
1) Handle init flow failures properly in iwlwifi driver, from Shahar S
Matityahu.
2) mac80211 TXQs need to be unscheduled on powersave start, from Felix
Fietkau.
3) SKB memory accounting fix in A-MDSU aggregation, from Felix Fietkau.
4) Increase RCU lock hold time in mlx5 FPGA code, from Saeed Mahameed.
5) Avoid checksum complete with XDP in mlx5, also from Saeed.
6) Fix netdev feature clobbering in ibmvnic driver, from Thomas Falcon.
7) Partial sent TLS record leak fix from Jakub Kicinski.
8) Reject zero size iova range in vhost, from Jason Wang.
9) Allow pending work to complete before clcsock release from Karsten
Graul.
10) Fix XDP handling max MTU in thunderx, from Matteo Croce.
11) A lot of protocols look at the sa_family field of a sockaddr before
validating it's length is large enough, from Tetsuo Handa.
12) Don't write to free'd pointer in qede ptp error path, from Colin Ian
King.
13) Have to recompile IP options in ipv4_link_failure because it can be
invoked from ARP, from Stephen Suryaputra.
14) Doorbell handling fixes in qed from Denis Bolotin.
15) Revert net-sysfs kobject register leak fix, it causes new problems.
From Wang Hai.
16) Spectre v1 fix in ATM code, from Gustavo A. R. Silva.
17) Fix put of BROPT_VLAN_STATS_PER_PORT in bridging code, from Nikolay
Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (111 commits)
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
tcp: tcp_grow_window() needs to respect tcp_space()
ocelot: Clean up stats update deferred work
ocelot: Don't sleep in atomic context (irqs_disabled())
net: bridge: fix netlink export of vlan_stats_per_port option
qed: fix spelling mistake "faspath" -> "fastpath"
tipc: set sysctl_tipc_rmem and named_timeout right range
tipc: fix link established but not in session
net: Fix missing meta data in skb with vlan packet
net: atm: Fix potential Spectre v1 vulnerabilities
net/core: work around section mismatch warning for ptp_classifier
net: bridge: fix per-port af_packet sockets
bnx2x: fix spelling mistake "dicline" -> "decline"
route: Avoid crash from dereferencing NULL rt->from
MAINTAINERS: normalize Woojung Huh's email address
bonding: fix event handling for stacked bonds
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
qed: Fix the DORQ's attentions handling
qed: Fix missing DORQ attentions
...
The patch a6dbe44275 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes: a6dbe44275 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When called with vmas_arg==NULL, get_user_pages_longterm() allocates
an array of nr_pages*8 which can easily get greater that the max order,
for example, registering memory for a 256GB guest does this and fails
in __alloc_pages_nodemask().
This adds a loop over chunks of entries to fit the max order limit.
Fixes: 678e174c4c ("powerpc/mm/iommu: allow migration of cma allocated pages during mm_iommu_do_alloc", 2019-03-05)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently mm_iommu_do_alloc() is called in 2 cases:
- VFIO_IOMMU_SPAPR_REGISTER_MEMORY ioctl() for normal memory:
this locks &mem_list_mutex and then locks mm::mmap_sem
several times when adjusting locked_vm or pinning pages;
- vfio_pci_nvgpu_regops::mmap() for GPU memory:
this is called with mm::mmap_sem held already and it locks
&mem_list_mutex.
So one can craft a userspace program to do special ioctl and mmap in
2 threads concurrently and cause a deadlock which lockdep warns about
(below).
We did not hit this yet because QEMU constructs the machine in a single
thread.
This moves the overlap check next to where the new entry is added and
reduces the amount of time spent with &mem_list_mutex held.
This moves locked_vm adjustment from under &mem_list_mutex.
This relies on mm_iommu_adjust_locked_vm() doing nothing when entries==0.
This is one of the lockdep warnings:
======================================================
WARNING: possible circular locking dependency detected
5.1.0-rc2-le_nv2_aikATfstn1-p1 #363 Not tainted
------------------------------------------------------
qemu-system-ppc/8038 is trying to acquire lock:
000000002ec6c453 (mem_list_mutex){+.+.}, at: mm_iommu_do_alloc+0x70/0x490
but task is already holding lock:
00000000fd7da97f (&mm->mmap_sem){++++}, at: vm_mmap_pgoff+0xf0/0x160
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&mm->mmap_sem){++++}:
lock_acquire+0xf8/0x260
down_write+0x44/0xa0
mm_iommu_adjust_locked_vm.part.1+0x4c/0x190
mm_iommu_do_alloc+0x310/0x490
tce_iommu_ioctl.part.9+0xb84/0x1150 [vfio_iommu_spapr_tce]
vfio_fops_unl_ioctl+0x94/0x430 [vfio]
do_vfs_ioctl+0xe4/0x930
ksys_ioctl+0xc4/0x110
sys_ioctl+0x28/0x80
system_call+0x5c/0x70
-> #0 (mem_list_mutex){+.+.}:
__lock_acquire+0x1484/0x1900
lock_acquire+0xf8/0x260
__mutex_lock+0x88/0xa70
mm_iommu_do_alloc+0x70/0x490
vfio_pci_nvgpu_mmap+0xc0/0x130 [vfio_pci]
vfio_pci_mmap+0x198/0x2a0 [vfio_pci]
vfio_device_fops_mmap+0x44/0x70 [vfio]
mmap_region+0x5d4/0x770
do_mmap+0x42c/0x650
vm_mmap_pgoff+0x124/0x160
ksys_mmap_pgoff+0xdc/0x2f0
sys_mmap+0x40/0x80
system_call+0x5c/0x70
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&mm->mmap_sem);
lock(mem_list_mutex);
lock(&mm->mmap_sem);
lock(mem_list_mutex);
*** DEADLOCK ***
1 lock held by qemu-system-ppc/8038:
#0: 00000000fd7da97f (&mm->mmap_sem){++++}, at: vm_mmap_pgoff+0xf0/0x160
Fixes: c10c21efa4 ("powerpc/vfio/iommu/kvm: Do not pin device memory", 2018-12-19)
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+cf4f2b6c24aff0a3edf6@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joel reported weird crashes using skiroot_defconfig, in his case we
jumped into an NX page:
kernel tried to execute exec-protected page (c000000002bff4f0) - exploit attempt? (uid: 0)
BUG: Unable to handle kernel instruction fetch
Faulting instruction address: 0xc000000002bff4f0
Looking at the disassembly, we had simply branched to that address:
c000000000c001bc 49fff335 bl c000000002bff4f0
But that didn't match the original kernel image:
c000000000c001bc 4bfff335 bl c000000000bff4f0 <kobject_get+0x8>
When STRICT_KERNEL_RWX is enabled, and we're using the radix MMU, we
call radix__change_memory_range() late in boot to change page
protections. We do that both to mark rodata read only and also to mark
init text no-execute. That involves walking the kernel page tables,
and clearing _PAGE_WRITE or _PAGE_EXEC respectively.
With radix we may use hugepages for the linear mapping, so the code in
radix__change_memory_range() uses eg. pmd_huge() to test if it has
found a huge mapping, and if so it stops the page table walk and
changes the PMD permissions.
However if the kernel is built without HUGETLBFS support, pmd_huge()
is just a #define that always returns 0. That causes the code in
radix__change_memory_range() to incorrectly interpret the PMD value as
a pointer to a PTE page rather than as a PTE at the PMD level.
We can see this using `dv` in xmon which also uses pmd_huge():
0:mon> dv c000000000000000
pgd @ 0xc000000001740000
pgdp @ 0xc000000001740000 = 0x80000000ffffb009
pudp @ 0xc0000000ffffb000 = 0x80000000ffffa009
pmdp @ 0xc0000000ffffa000 = 0xc00000000000018f <- this is a PTE
ptep @ 0xc000000000000100 = 0xa64bb17da64ab07d <- kernel text
The end result is we treat the value at 0xc000000000000100 as a PTE
and clear _PAGE_WRITE or _PAGE_EXEC, potentially corrupting the code
at that address.
In Joel's specific case we cleared the sign bit in the offset of the
branch, causing a backward branch to turn into a forward branch which
caused us to branch into a non-executable page. However the exact
nature of the crash depends on kernel version, compiler version, and
other factors.
We need to fix radix__change_memory_range() to not use accessors that
depend on HUGETLBFS, but we also have radix memory hotplug code that
uses pmd_huge() etc that will also need fixing. So for now just
disallow the broken combination of Radix with HUGETLBFS disabled.
The only defconfig we have that is affected is skiroot_defconfig, so
turn on HUGETLBFS there so that it still gets Radix.
Fixes: 566ca99af0 ("powerpc/mm/radix: Add dummy radix_enabled()")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have two Dell laptops which have the codec 10ec0236 and 10ec0256
respectively, the headset mic on them can't work, need to apply the
quirk of ALC255_FIXUP_DELL1_MIC_NO_PRESENCE. So adding their pin
configurations in the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inline assembly code changed in this patch should really use "Q"
constraint "Memory reference without index register and with short
displacement". The kernel build with kasan instrumentation enabled
might occasionally break otherwise (due to stack instrumentation).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The audio configuration is only valid if the HDMI codec has been
properly set up. Do not attempt to set up audio before that happens
because it causes a division by zero.
Note that this is only problematic on Tegra20 and Tegra30. Later chips
implement the division instructions which return zero when dividing by
zero and don't throw an exception.
Fixes: db5adf4d6d ("drm/tegra: hdmi: Fix audio to work with any pixel clock rate")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It looks like the new socket options only work correctly
for native execution, but in case of compat mode fall back
to the old behavior as we ignore the 'old_timeval' flag.
Rework so we treat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW the
same way in compat and native 32-bit mode.
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Fixes: a9beb86ae6 ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9 ("tipc: change socket buffer overflow control to respect sk_rcvbuf")
Fixes: a5325ae5b8 ("tipc: add name distributor resiliency queue")
Signed-off-by: Jie Liu <liujie165@huawei.com>
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit 91986ee166 ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
arg is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/atm/lec.c:715 lec_mcast_attach() warn: potential spectre issue 'dev_lec' [r] (local cap)
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routine ptp_classifier_init() uses an initializer for an
automatic struct type variable which refers to an __initdata
symbol. This is perfectly legal, but may trigger a section
mismatch warning when running the compiler in -fpic mode, due
to the fact that the initializer may be emitted into an anonymous
.data section thats lack the __init annotation. So work around it
by using assignments instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
The intended behavior of function ipmi_hardcode_init_one() is to default
to kcs interface when no type argument is presented when initializing
ipmi with hard coded addresses.
However, the array of char pointers allocated on the stack by function
ipmi_hardcode_init() was not inited to zeroes, so it contained stack
debris.
Consequently, passing the cruft stored in this array to function
ipmi_hardcode_init_one() caused a crash when it was unable to detect
that the char * being passed was nonsense and tried to access the
address specified by the bogus pointer.
The fix is simply to initialize the si_type array to zeroes, so if
there were no type argument given to at the command line, function
ipmi_hardcode_init_one() could properly default to the kcs interface.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Message-Id: <1554837603-40299-1-git-send-email-tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
An extra memset was put into a place that cleared the interface
type.
Reported-by: Tony Camuso <tcamuso@redhat.com>
Fixes: 3cd83bac48 ("ipmi: Consolidate the adding of platform devices")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Pull RISC-V fixes from Palmer Dabbelt:
"This contains an assortment of RISC-V-related fixups that we found
after rc4. They're all really unrelated:
- The addition of a 32-bit defconfig, to emphasize testing the 32-bit
port.
- A device tree bindings patch, which is pre-work for some patches
that target 5.2.
- A fix to support booting on systems with more physical memory than
the maximum supported by the kernel"
* tag 'riscv-for-linus-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Fix Maximum Physical Memory 2GiB option for 64bit systems
dt-bindings: clock: sifive: add FU540-C000 PRCI clock constants
RISC-V: Add separate defconfig for 32bit systems
Pull KVM fixes from Paolo Bonzini:
"5.1 keeps its reputation as a big bugfix release for KVM x86.
- Fix for a memory leak introduced during the merge window
- Fixes for nested VMX with ept=0
- Fixes for AMD (APIC virtualization, NMI injection)
- Fixes for Hyper-V under KVM and KVM under Hyper-V
- Fixes for 32-bit SMM and tests for SMM virtualization
- More array_index_nospec peppering"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
KVM: fix spectrev1 gadgets
KVM: x86: fix warning Using plain integer as NULL pointer
selftests: kvm: add a selftest for SMM
selftests: kvm: fix for compilers that do not support -no-pie
selftests: kvm/evmcs_test: complete I/O before migrating guest state
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
KVM: x86: clear SMM flags before loading state while leaving SMM
KVM: x86: Open code kvm_set_hflags
KVM: x86: Load SMRAM in a single shot when leaving SMM
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
KVM: x86: Raise #GP when guest vCPU do not support PMU
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
svm/avic: Fix invalidate logical APIC id entry
Revert "svm: Fix AVIC incomplete IPI emulation"
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM: nVMX: always use early vmcs check when EPT is disabled
KVM: nVMX: allow tests to use bad virtual-APIC page address
...
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
core:
Mao Han:
- Use hweight64() instead of hweight_long(attr.sample_regs_user) when parsing
samples, this is what the kernel uses and fixes de problem in 32-bit
architectures such as C-SKY that have more than 32 registers that can come
in a sample.
perf stat:
Jiri Olsa:
- Disable DIR_FORMAT feature for 'perf stat record', fixing an assert()
failure.
Intel PT:
Adrian Hunter:
- Fix use of parent_id in calls_view in export-to-sqlite.py.
BPF:
Gustavo A. R. Silva:
- Fix lock/unlock imbalances when processing BPF/BTF info, found by the
coverity tool.
libtraceevent:
Rikard Falkeborn:
- Fix missing equality check for strcmp(), detected by the cppcheck tool.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is a small race window in the card disconnection code that
allows the registration of another card with the very same card id.
This leads to a warning in procfs creation as caught by syzkaller.
The problem is that we delete snd_cards and snd_cards_lock entries at
the very beginning of the disconnection procedure. This makes the
slot available to be assigned for another card object while the
disconnection procedure is being processed. Then it becomes possible
to issue a procfs registration with the existing file name although we
check the conflict beforehand.
The fix is simply to move the snd_cards and snd_cards_lock clearances
at the end of the disconnection procedure. The references to these
entries are merely either from the global proc files like
/proc/asound/cards or from the card registration / disconnection, so
it should be fine to shift at the very end.
Reported-by: syzbot+48df349490c36f9f54ab@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
syzbot reported the following warning:
[ ] WARNING: CPU: 4 PID: 17089 at kernel/sched/deadline.c:255 task_non_contending+0xae0/0x1950
line 255 of deadline.c is:
WARN_ON(hrtimer_active(&dl_se->inactive_timer));
in task_non_contending().
Unfortunately, in some cases (for example, a deadline task
continuosly blocking and waking immediately) it can happen that
a task blocks (and task_non_contending() is called) while the
0-lag timer is still active.
In this case, the safest thing to do is to immediately decrease
the running bandwidth of the task, without trying to re-arm the 0-lag timer.
Signed-off-by: luca abeni <luca.abeni@santannapisa.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: chengjian (D) <cj.chengjian@huawei.com>
Link: https://lkml.kernel.org/r/20190325131530.34706-1-luca.abeni@santannapisa.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With extremely short cfs_period_us setting on a parent task group with a large
number of children the for loop in sched_cfs_period_timer() can run until the
watchdog fires. There is no guarantee that the call to hrtimer_forward_now()
will ever return 0. The large number of children can make
do_sched_cfs_period_timer() take longer than the period.
NMI watchdog: Watchdog detected hard LOCKUP on cpu 24
RIP: 0010:tg_nop+0x0/0x10
<IRQ>
walk_tg_tree_from+0x29/0xb0
unthrottle_cfs_rq+0xe0/0x1a0
distribute_cfs_runtime+0xd3/0xf0
sched_cfs_period_timer+0xcb/0x160
? sched_cfs_slack_timer+0xd0/0xd0
__hrtimer_run_queues+0xfb/0x270
hrtimer_interrupt+0x122/0x270
smp_apic_timer_interrupt+0x6a/0x140
apic_timer_interrupt+0xf/0x20
</IRQ>
To prevent this we add protection to the loop that detects when the loop has run
too many times and scales the period and quota up, proportionally, so that the timer
can complete before then next period expires. This preserves the relative runtime
quota while preventing the hard lockup.
A warning is issued reporting this state and the new values.
Signed-off-by: Phil Auld <pauld@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190319130005.25492-1-pauld@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the oplock break handler, writing pending changes from pages puts
the FileInfo handle. If the refcount reaches zero it closes the handle
and waits for any oplock break handler to return, thus causing a deadlock.
To prevent this situation:
* We add a wait flag to cifsFileInfo_put() to decide whether we should
wait for running/pending oplock break handlers
* We keep an additionnal reference of the SMB FileInfo handle so that
for the rest of the handler putting the handle won't close it.
- The ref is bumped everytime we queue the handler via the
cifs_queue_oplock_break() helper.
- The ref is decremented at the end of the handler
This bug was triggered by xfstest 464.
Also important fix to address the various reports of
oops in smb2_push_mandatory_locks
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
If we enter smb2_query_symlink() for something that is not a symlink
and where the SMB2_open() would succeed we would never end up
closing this handle and would thus leak a handle on the server.
Fix this by immediately calling SMB2_close() on successfull open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
There is a KASAN slab-out-of-bounds:
BUG: KASAN: slab-out-of-bounds in _copy_from_iter_full+0x783/0xaa0
Read of size 80 at addr ffff88810c35e180 by task mount.cifs/539
CPU: 1 PID: 539 Comm: mount.cifs Not tainted 4.19 #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
Call Trace:
dump_stack+0xdd/0x12a
print_address_description+0xa7/0x540
kasan_report+0x1ff/0x550
check_memory_region+0x2f1/0x310
memcpy+0x2f/0x80
_copy_from_iter_full+0x783/0xaa0
tcp_sendmsg_locked+0x1840/0x4140
tcp_sendmsg+0x37/0x60
inet_sendmsg+0x18c/0x490
sock_sendmsg+0xae/0x130
smb_send_kvec+0x29c/0x520
__smb_send_rqst+0x3ef/0xc60
smb_send_rqst+0x25a/0x2e0
compound_send_recv+0x9e8/0x2af0
cifs_send_recv+0x24/0x30
SMB2_open+0x35e/0x1620
open_shroot+0x27b/0x490
smb2_open_op_close+0x4e1/0x590
smb2_query_path_info+0x2ac/0x650
cifs_get_inode_info+0x1058/0x28f0
cifs_root_iget+0x3bb/0xf80
cifs_smb3_do_mount+0xe00/0x14c0
cifs_do_mount+0x15/0x20
mount_fs+0x5e/0x290
vfs_kern_mount+0x88/0x460
do_mount+0x398/0x31e0
ksys_mount+0xc6/0x150
__x64_sys_mount+0xea/0x190
do_syscall_64+0x122/0x590
entry_SYSCALL_64_after_hwframe+0x44/0xa9
It can be reproduced by the following step:
1. samba configured with: server max protocol = SMB2_10
2. mount -o vers=default
When parse the mount version parameter, the 'ops' and 'vals'
was setted to smb30, if negotiate result is smb21, just
update the 'ops' to smb21, but the 'vals' is still smb30.
When add lease context, the iov_base is allocated with smb21
ops, but the iov_len is initiallited with the smb30. Because
the iov_len is longer than iov_base, when send the message,
copy array out of bounds.
we need to keep the 'ops' and 'vals' consistent.
Fixes: 9764c02fcb ("SMB3: Add support for multidialect negotiate (SMB2.1 and later)")
Fixes: d5c7076b77 ("smb3: add smb3.1.1 to default dialect list")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_read+0x1136/0x1190
Read of size 8 at addr ffff8880b4e45e50 by task ln/1009
Should not release the 'req' because it will use in the trace.
Fixes: eccb4422cf ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_write+0x1342/0x1580
Read of size 8 at addr ffff8880b6a8e450 by task ln/4196
Should not release the 'req' because it will use in the trace.
Fixes: eccb4422cf ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
There was a missing comparison with 0 when checking if type is "s64" or
"u64". Therefore, the body of the if-statement was entered if "type" was
"u64" or not "s64", which made the first strcmp() redundant since if
type is "u64", it's not "s64".
If type is "s64", the body of the if-statement is not entered but since
the remainder of the function consists of if-statements which will not
be entered if type is "s64", we will just return "val", which is
correct, albeit at the cost of a few more calls to strcmp(), i.e., it
will behave just as if the if-statement was entered.
If type is neither "s64" or "u64", the body of the if-statement will be
entered incorrectly and "val" returned. This means that any type that is
checked after "s64" and "u64" is handled the same way as "s64" and
"u64", i.e., the limiting of "val" to fit in for example "s8" is never
reached.
This was introduced in the kernel tree when the sources were copied from
trace-cmd in commit f7d82350e5 ("tools/events: Add files to create
libtraceevent.a"), and in the trace-cmd repo in 1cdbae6035cei
("Implement typecasting in parser") when the function was introduced,
i.e., it has always behaved the wrong way.
Detected by cppcheck.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Fixes: f7d82350e5 ("tools/events: Add files to create libtraceevent.a")
Link: http://lkml.kernel.org/r/20190409091529.2686-1-rikard.falkeborn@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull clockevent/clocksource fixes from Daniel Lezcano:
- Fix TIMER_OF missing option dependency for npcm (Arnd Bergmann)
- Remove a pointless macro call for arm_arch_timer (Yangtao Li)
- Fix wrong compatible string for oxnas (Neil Armstrong)
- Fix compilation warning by removing a dead function on omap (Nathan Chancellor)
The ALSA proc helper manages the child nodes in a linked list, but its
addition and deletion is done without any lock. This leads to a
corruption if they are operated concurrently. Usually this isn't a
problem because the proc entries are added sequentially in the driver
probe procedure itself. But the card registrations are done often
asynchronously, and the crash could be actually reproduced with
syzkaller.
This patch papers over it by protecting the link addition and deletion
with the parent's mutex. There is "access" mutex that is used for the
file access, and this can be reused for this purpose as well.
Reported-by: syzbot+48df349490c36f9f54ab@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In __apic_accept_irq() interface trig_mode is int and actually on some code
paths it is set above u8:
kvm_apic_set_irq() extracts it from 'struct kvm_lapic_irq' where trig_mode
is u16. This is done on purpose as e.g. kvm_set_msi_irq() sets it to
(1 << 15) & e->msi.data
kvm_apic_local_deliver sets it to reg & (1 << 15).
Fix the immediate issue by making 'tm' into u16. We may also want to adjust
__apic_accept_irq() interface and use proper sizes for vector, level,
trig_mode but this is not urgent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Changed passing argument as "0 to NULL" which resolves below sparse warning
arch/x86/kvm/x86.c:3096:61: warning: Using plain integer as NULL pointer
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a simple test for SMM, based on VMX. The test implements its own
sync between the guest and the host as using our ucall library seems to
be too cumbersome: SMI handler is happening in real-address mode.
This patch also fixes KVM_SET_NESTED_STATE to happen after
KVM_SET_VCPU_EVENTS, in fact it places it last. This is because
KVM needs to know whether the processor is in SMM or not.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-no-pie was added to GCC at the same time as their configuration option
--enable-default-pie. Compilers that were built before do not have
-no-pie, but they also do not need it. Detect the option at build
time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Starting state migration after an IO exit without first completing IO
may result in test failures. We already have two tests that need this
(this patch in fact fixes evmcs_test, similar to what was fixed for
state_test in commit 0f73bbc851, "KVM: selftests: complete IO before
migrating guest state", 2019-03-13) and a third is coming. So, move the
code to vcpu_save_state, and while at it do not access register state
until after I/O is complete.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Invoking the 64-bit variation on a 32-bit kenrel will crash the guest,
trigger a WARN, and/or lead to a buffer overrun in the host, e.g.
rsm_load_state_64() writes r8-r15 unconditionally, but enum kvm_reg and
thus x86_emulate_ctxt._regs only define r8-r15 for CONFIG_X86_64.
KVM allows userspace to report long mode support via CPUID, even though
the guest is all but guaranteed to crash if it actually tries to enable
long mode. But, a pure 32-bit guest that is ignorant of long mode will
happily plod along.
SMM complicates things as 64-bit CPUs use a different SMRAM save state
area. KVM handles this correctly for 64-bit kernels, e.g. uses the
legacy save state map if userspace has hid long mode from the guest,
but doesn't fare well when userspace reports long mode support on a
32-bit host kernel (32-bit KVM doesn't support 64-bit guests).
Since the alternative is to crash the guest, e.g. by not loading state
or explicitly requesting shutdown, unconditionally use the legacy SMRAM
save state map for 32-bit KVM. If a guest has managed to get far enough
to handle SMIs when running under a weird/buggy userspace hypervisor,
then don't deliberately crash the guest since there are no downsides
(from KVM's perspective) to allow it to continue running.
Fixes: 660a5d517a ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save
state area, i.e. don't save/restore EFER across SMM transitions. KVM
somewhat models this, e.g. doesn't clear EFER on entry to SMM if the
guest doesn't support long mode. But during RSM, KVM unconditionally
clears EFER so that it can get back to pure 32-bit mode in order to
start loading CRs with their actual non-SMM values.
Clear EFER only when it will be written when loading the non-SMM state
so as to preserve bits that can theoretically be set on 32-bit vCPUs,
e.g. KVM always emulates EFER_SCE.
And because CR4.PAE is cleared only to play nice with EFER, wrap that
code in the long mode check as well. Note, this may result in a
compiler warning about cr4 being consumed uninitialized. Re-read CR4
even though it's technically unnecessary, as doing so allows for more
readable code and RSM emulation is not a performance critical path.
Fixes: 660a5d517a ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Stop dancing around the issue of HF_SMM_MASK being set when
loading SMSTATE into architectural state, e.g. by toggling it for
problematic flows, and simply clear HF_SMM_MASK prior to loading
architectural state (from SMRAM save state area).
Reported-by: Jon Doron <arilou@gmail.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 5bea5123cb ("KVM: VMX: check nested state and CR4.VMXE against SMM")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Prepare for clearing HF_SMM_MASK prior to loading state from the SMRAM
save state map, i.e. kvm_smm_changed() needs to be called after state
has been loaded and so cannot be done automatically when setting
hflags from RSM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RSM emulation is currently broken on VMX when the interrupted guest has
CR4.VMXE=1. Rather than dance around the issue of HF_SMM_MASK being set
when loading SMSTATE into architectural state, ideally RSM emulation
itself would be reworked to clear HF_SMM_MASK prior to loading non-SMM
architectural state.
Ostensibly, the only motivation for having HF_SMM_MASK set throughout
the loading of state from the SMRAM save state area is so that the
memory accesses from GET_SMSTATE() are tagged with role.smm. Load
all of the SMRAM save state area from guest memory at the beginning of
RSM emulation, and load state from the buffer instead of reading guest
memory one-by-one.
This paves the way for clearing HF_SMM_MASK prior to loading state,
and also aligns RSM with the enter_smm() behavior, which fills a
buffer and writes SMRAM save state in a single go.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Issue was discovered when running kvm-unit-tests on KVM running as L1 on
top of Hyper-V.
When vmx_instruction_intercept unit-test attempts to run RDPMC to test
RDPMC-exiting, it is intercepted by L1 KVM which it's EXIT_REASON_RDPMC
handler raise #GP because vCPU exposed by Hyper-V doesn't support PMU.
Instead of unit-test expectation to be reflected with EXIT_REASON_RDPMC.
The reason vmx_instruction_intercept unit-test attempts to run RDPMC
even though Hyper-V doesn't support PMU is because L1 expose to L2
support for RDPMC-exiting. Which is reasonable to assume that is
supported only in case CPU supports PMU to being with.
Above issue can easily be simulated by modifying
vmx_instruction_intercept config in x86/unittests.cfg to run QEMU with
"-cpu host,+vmx,-pmu" and run unit-test.
To handle issue, change KVM to expose RDPMC-exiting only when guest
supports PMU.
Reported-by: Saar Amar <saaramar@microsoft.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Before this change, reading a VMware pseduo PMC will succeed even when
PMU is not supported by guest. This can easily be seen by running
kvm-unit-test vmware_backdoors with "-cpu host,-pmu" option.
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
guest xcr0 could leak into host when MCE happens in guest mode. Because
do_machine_check() could schedule out at a few places.
For example:
kvm_load_guest_xcr0
...
kvm_x86_ops->run(vcpu) {
vmx_vcpu_run
vmx_complete_atomic_exit
kvm_machine_check
do_machine_check
do_memory_failure
memory_failure
lock_page
In this case, host_xcr0 is 0x2ff, guest vcpu xcr0 is 0xff. After schedule
out, host cpu has guest xcr0 loaded (0xff).
In __switch_to {
switch_fpu_finish
copy_kernel_to_fpregs
XRSTORS
If any bit i in XSTATE_BV[i] == 1 and xcr0[i] == 0, XRSTORS will
generate #GP (In this case, bit 9). Then ex_handler_fprestore kicks in
and tries to reinitialize fpu by restoring init fpu state. Same story as
last #GP, except we get DOUBLE FAULT this time.
Cc: stable@vger.kernel.org
Signed-off-by: WANG Chao <chao.wang@ucloud.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P,
the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing
shows that we're sometimes able to deliver a few but never all.
When we're trying to inject an NMI we may fail to do so immediately for
various reasons, however, we still need to inject it so enable_nmi_window()
arms nmi_singlestep mode. #DB occurs as expected, but we're not checking
for pending NMIs before entering the guest and unless there's a different
event to process, the NMI will never get delivered.
Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure
pending NMIs are checked and possibly injected.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only clear the valid bit when invalidate logical APIC id entry.
The current logic clear the valid bit, but also set the rest of
the bits (including reserved bits) to 1.
Fixes: 98d90582be ('svm: Fix AVIC DFR and LDR handling')
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit bb218fbcfa.
As Oren Twaig pointed out the old discussion:
https://patchwork.kernel.org/patch/8292231/
that the change coud potentially cause an extra IPI to be sent to
the destination vcpu because the AVIC hardware already set the IRR bit
before the incomplete IPI #VMEXIT with id=1 (target vcpu is not running).
Since writting to ICR and ICR2 will also set the IRR. If something triggers
the destination vcpu to get scheduled before the emulation finishes, then
this could result in an additional IPI.
Also, the issue mentioned in the commit bb218fbcfa was misdiagnosed.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Oren Twaig <oren@scalemp.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM bases its memory usage limits on the total number of guest pages
across all memslots. However, those limits, and the calculations to
produce them, use 32 bit unsigned integers. This can result in overflow
if a VM has more guest pages that can be represented by a u32. As a
result of this overflow, KVM can use a low limit on the number of MMU
pages it will allocate. This makes KVM unable to map all of guest memory
at once, prompting spurious faults.
Tested: Ran all kvm-unit-tests on an Intel Haswell machine. This patch
introduced no new failures.
Signed-off-by: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The remaining failures of vmx.flat when EPT is disabled are caused by
incorrectly reflecting VMfails to the L1 hypervisor. What happens is
that nested_vmx_restore_host_state corrupts the guest CR3, reloading it
with the host's shadow CR3 instead, because it blindly loads GUEST_CR3
from the vmcs01.
For simplicity let's just always use hardware VMCS checks when EPT is
disabled. This way, nested_vmx_restore_host_state is not reached at
all (or at least shouldn't be reached).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
err_spi is used when SERIAL_SC16IS7XX_SPI is enabled, so make
the label only available under SERIAL_SC16IS7XX_SPI option.
Otherwise, the below warning appears.
drivers/tty/serial/sc16is7xx.c:1523:1: warning: label ‘err_spi’ defined but not used [-Wunused-label]
err_spi:
^~~~~~~
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Fixes: ac0cdb3d99 ("sc16is7xx: missing unregister/delete driver on error in sc16is7xx_init()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 008258d995 ("clocksource/drivers/timer-ti-dm: Make
omap_dm_timer_set_load_start() static") made omap_dm_time_set_load_start
static because its prototype was not defined in a header. Unfortunately,
this causes a build warning on multi_v7_defconfig because this function
is not used anywhere in this translation unit:
drivers/clocksource/timer-ti-dm.c:589:12: error: unused function
'omap_dm_timer_set_load_start' [-Werror,-Wunused-function]
In fact, omap_dm_timer_set_load_start hasn't been used anywhere since
commit f190be7f39 ("staging: tidspbridge: remove driver") and the
prototype was removed in commit 592ea6bd1f ("clocksource: timer-ti-dm:
Make unexported functions static"), which is probably where this should
have happened.
Fixes: 592ea6bd1f ("clocksource: timer-ti-dm: Make unexported functions static")
Fixes: 008258d995 ("clocksource/drivers/timer-ti-dm: Make omap_dm_timer_set_load_start() static")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+54c2f58f15fe6876b6ad@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanwoo writes:
Update extcon for v5.1-rc4
Detailed description for this pull request:
1. Fix the build issue of extcon-ptn5150.c driver by editing
the module dependency in Kconfig.
* tag 'extcon-fixes-for-5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon:
extcon: ptn5150: fix COMPILE_TEST dependencies
Current implementation was not properly handling frwr memory
registrations. This was uncovered by commit 27f26cec761das ("xprtrdma:
Plant XID in on-the-wire RDMA offset (FRWR)") in which xprtrdma, which is
used for NFS over RDMA, started failing as it was the first ULP to modify
the ib_mr iova resulting in the NFS server getting REMOTE ACCESS ERROR
when attempting to perform RDMA Writes to the client.
The fix is to properly capture the true iova, offset, and length in the
call to ib_map_mr_sg, and then update the iova when processing the
IB_WR_REG_MEM on the send queue.
Fixes: a41081aa59 ("IB/rdmavt: Add support for ib_map_mr_sg")
Cc: stable@vger.kernel.org
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Josh Collier <josh.d.collier@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
As mentioned in the comment, there are some special cases where we can simply
clear the TPR shadow bit from the CPU-based execution controls in the vmcs02.
Handle them so that we can remove some XFAILs from vmx.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xose Vazquez Perez reported boot warnings when NX is disabled on the kernel command line.
__early_set_fixmap() triggers this warning:
attempted to set unsupported pgprot: 8000000000000163
bits: 8000000000000000
supported: 7fffffffffffffff
WARNING: CPU: 0 PID: 0 at arch/x86/include/asm/pgtable.h:537
__early_set_fixmap+0xa2/0xff
because it uses __default_kernel_pte_mask to mask out unsupported bits.
Use __supported_pte_mask instead.
Disabling NX on the command line also triggers the NX warning in the page
table mapping check:
WARNING: CPU: 1 PID: 1 at arch/x86/mm/dump_pagetables.c:262 note_page+0x2ae/0x650
....
Make the warning depend on NX set in __supported_pte_mask.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Tested-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.21.1904151037530.1729@nanos.tec.linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit introduced a bug in one of our error paths:
819319fc93 ("kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()")
it missed to handle the return value of kprobe_optready() as
error-value. In reality, the kprobe_optready() returns a bool
result, so "true" case must be passed instead of 0.
This causes some errors on kprobe boot-time selftests on ARM:
[ ] Beginning kprobe tests...
[ ] Probe ARM code
[ ] kprobe
[ ] kretprobe
[ ] ARM instruction simulation
[ ] Check decoding tables
[ ] Run test cases
[ ] FAIL: test_case_handler not run
[ ] FAIL: Test andge r10, r11, r14, asr r7
[ ] FAIL: Scenario 11
...
[ ] FAIL: Scenario 7
[ ] Total instruction simulation tests=1631, pass=1433 fail=198
[ ] kprobe tests failed
This can happen if an optimized probe is unregistered and next
kprobe is registered on same address until the previous probe
is not reclaimed.
If this happens, a hidden aggregated probe may be kept in memory,
and no new kprobe can probe same address. Also, in that case
register_kprobe() will return "1" instead of minus error value,
which can mislead caller logic.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # v5.0+
Fixes: 819319fc93 ("kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()")
Link: http://lkml.kernel.org/r/155530808559.32517.539898325433642204.stgit@devnote2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If lockdep_register_key() and lockdep_unregister_key() are called with
debug_locks == false then the following warning is reported:
WARNING: CPU: 2 PID: 15145 at kernel/locking/lockdep.c:4920 lockdep_unregister_key+0x1ad/0x240
That warning is reported because lockdep_unregister_key() ignores the
value of 'debug_locks' and because the behavior of lockdep_register_key()
depends on whether or not 'debug_locks' is set. Fix this inconsistency
by making lockdep_unregister_key() take 'debug_locks' again into
account.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: shenghui <shhuiw@foxmail.com>
Fixes: 90c1cba2b3 ("locking/lockdep: Zap lock classes even with lock debugging disabled")
Link: http://lkml.kernel.org/r/20190415170538.23491-1-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When SCSI blk-mq is enabled, there is a bug in handling errors in
scsi_queue_rq. Specifically, the bug is not setting result field of
scsi_request correctly when the dispatch of the command has been
failed. Since the upper layer code including the sg_io ioctl expects to
receive any error status from result field of scsi_request, the error is
silently ignored and this could cause data corruptions for some
applications.
Fixes: d285203cf6 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jaesoo Lee <jalee@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull libnvdimm fixes from Dan Williams:
"I debated holding this back for the v5.2 merge window due to the size
of the "zero-key" changes, but affected users would benefit from
having the fixes sooner. It did not make sense to change the zero-key
semantic in isolation for the "secure-erase" command, but instead
include it for all security commands.
The short background on the need for these changes is that some NVDIMM
platforms enable security with a default zero-key rather than let the
OS specify the initial key. This makes the security enabling that
landed in v5.0 unusable for some users.
Summary:
- Compatibility fix for nvdimm-security implementations with a
default zero-key.
- Miscellaneous small fixes for out-of-bound accesses, cleanup after
initialization failures, and missing debug messages"
* tag 'libnvdimm-fixes-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Retain security state after overwrite
libnvdimm/pmem: fix a possible OOB access when read and write pmem
libnvdimm/security, acpi/nfit: unify zero-key for all security commands
libnvdimm/security: provide fix for secure-erase to use zero-key
libnvdimm/btt: Fix a kmemdup failure check
libnvdimm/namespace: Fix a potential NULL pointer dereference
acpi/nfit: Always dump _DSM output payload
Pull fsdax fix from Dan Williams:
"A single filesystem-dax fix. It has been lingering in -next for a long
while and there are no other fsdax fixes on the horizon:
- Avoid a crash scenario with architectures like powerpc that require
'pgtable_deposit' for the zero page"
* tag 'fsdax-fix-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
fs/dax: Deposit pagetable even when installing zero page
MAINTAINERS contains a lower-case and upper-case variant of
Woojung Huh' s email address.
Only keep the lower-case variant in MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
Second set of fixes for 5.1.
iwlwifi
* add some new PCI IDs (plus a struct name change they depend on)
* fix crypto with new devices, namely 22560 and above
* fix for a potential deadlock in the TX path
* a fix for offloaded rate-control
* support new PCI HW IDs which use a new FW
mt76
* fix lock initialisation and a possible deadlock
* aggregation fixes
rt2x00
* fix sequence numbering during retransmits
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c21b8fd8f (MIPS: seccomp: Handle indirect system calls (o32))
added indirect syscall detection for O32 processes running on MIPS64,
but it did not work correctly for big endian kernel/processes. The
reason is that the syscall number is loaded from ARG1 using the lw
instruction while this is a 64-bit value, so zero is loaded instead of
the syscall number.
Fix the code by using the ld instruction instead. When running a 32-bit
processes on a 64 bit CPU, the values are properly sign-extended, so it
ensures the value passed to syscall_trace_enter is correct.
Recent systemd versions with seccomp enabled whitelist the getpid
syscall for their internal processes (e.g. systemd-journald), but call
it through syscall(SYS_getpid). This fix therefore allows O32 big endian
systems with a 64-bit kernel to run recent systemd versions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@vger.kernel.org> # v3.15+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
If we have multiple threads, one doing io_uring_enter() while the other
is doing io_uring_register(), we can run into a deadlock between the
two. io_uring_register() must wait for existing users of the io_uring
instance to exit. But it does so while holding the io_uring mutex.
Callers of io_uring_enter() may need this mutex to make progress (and
eventually exit). If we wait for users to exit in io_uring_register(),
we can't do so with the io_uring mutex held without potentially risking
a deadlock.
Drop the io_uring mutex while waiting for existing callers to exit. This
is safe and guaranteed to make forward progress, since we already killed
the percpu ref before doing so. Hence later callers of io_uring_enter()
will be rejected.
Reported-by: syzbot+16dc03452dee970a0c3e@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We are no longer calling bxt_ddi_phy_calc_lane_lat_optim_mask() when
intel{hdmi,dp}_compute_config() succeeds, and instead only call it
when those fail. This is fallout from the bool->int
.compute_config() conversion which failed to invert the return
value check before calling bxt_ddi_phy_calc_lane_lat_optim_mask().
Let's just replace it with an early bailout so that it's harder
to miss.
This restores the correct latency optim setting calculation
(which could fix some real failures), and avoids the
MISSING_CASE() from bxt_ddi_phy_calc_lane_lat_optim_mask()
after intel{hdmi,dp}_compute_config() has failed.
Cc: Lyude Paul <lyude@redhat.com>
Fixes: 204474a6b8 ("drm/i915: Pass down rc in intel_encoder->compute_config()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109373
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190411164925.28491-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 7a412b8f60)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add the io_uring and pidfd_send_signal system calls to all architectures.
These system calls are designed to handle both native and compat tasks,
so all entries are the same across architectures, only arm-compat and
the generic tale still use an old format.
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> (s390)
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
spdxcheck.py complains:
drivers/power/supply/goldfish_battery.c: 1:28 Invalid License ID: GPL
which is correct because GPL is not a valid identifier. Of course this
could have been caught by checkpatch.pl _before_ submitting or merging the
patch.
WARNING: 'SPDX-License-Identifier: GPL' is not supported in LICENSES/...
#19: FILE: drivers/power/supply/goldfish_battery.c:1:
+// SPDX-License-Identifier: GPL
Which is absolutely hillarious as the commit introducing this wreckage says
in the changelog:
There was a checkpatch complain:
"Missing or malformed SPDX-License-Identifier tag".
Oh well. Replacing a checkpatch warning by a different checkpatch warning
is a really useful exercise.
Use the proper GPL-2.0 identifier which is what the boiler plate in the
file had originally.
Fixes: e75e3a125b ("drivers: power: supply: goldfish_battery: Put an SPDX tag")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug feature entries have been used with up to 5 arguents
(including the pointer to the format string) but there was only
space reserved for 4 arguemnts. So now the registration does
reserve space for 5 times a long value.
This fixes a sometime appearing weired value as the last
value of an debug feature entry like this:
... pkey_sec2protkey zcrypt_send_cprb (cardnr=10 domain=12)
failed with errno -2143346254
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Christian Rund <Christian.Rund@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Sven Auhagen reported that a 2nd ping request will fail if 'fully-random'
mode is used.
Reason is that if no proto information is given, min/max are both 0,
so we set the icmp id to 0 instead of chosing a random value between
0 and 65535.
Update test case as well to catch this, without fix this yields:
[..]
ERROR: cannot ping ns1 from ns2 with ip masquerade fully-random (attempt 2)
ERROR: cannot ping ns1 from ns2 with ipv6 masquerade fully-random (attempt 2)
... becaus 2nd ping clashes with existing 'id 0' icmp conntrack and gets
dropped.
Fixes: 203f2e7820 ("netfilter: nat: remove l4proto->unique_tuple")
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I believe that "hook->num" can be up to UINT_MAX. Shifting more than
31 bits would is undefined in C but in practice it would lead to shift
wrapping. That would lead to an array overflow in nf_tables_addchain():
ops->hook = hook.type->hooks[ops->hooknum];
Fixes: fe19c04ca1 ("netfilter: nf_tables: remove nhooks field from struct nft_af_info")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
else, we leak the addresses to userspace via ctnetlink events
and dumps.
Compute an ID on demand based on the immutable parts of nf_conn struct.
Another advantage compared to using an address is that there is no
immediate re-use of the same ID in case the conntrack entry is freed and
reallocated again immediately.
Fixes: 3583240249 ("[NETFILTER]: nf_conntrack_expect: kill unique ID")
Fixes: 7f85f91472 ("[NETFILTER]: nf_conntrack: kill unique ID")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[Why]
On some compositors, with two monitors attached, VT terminal
switch can cause a graphical issue by the following means:
There are two streams, one for each monitor. Each stream has one
plane
current state:
M1:S1->P1
M2:S2->P2
The user calls for a terminal switch and a commit is made to
change both planes to linear swizzle mode. In atomic check,
a new dc_state is constructed with new planes on each stream
new state:
M1:S1->P3
M2:S2->P4
In commit tail, each stream is committed, one at a time. The first
stream (S1) updates properly, triggerring a full update and replacing
the state
current state:
M1:S1->P3
M2:S2->P4
The update for S2 comes in, but dc detects that there is no difference
between the stream and plane in the new and current states, and so
triggers a fast update. The fast update does not program swizzle,
so the second monitor is corrupted
[How]
Add a flag to dc_plane_state that forces full updates
When a stream undergoes a full update, set this flag on all changed
planes, then clear it on the current stream
Subsequent streams will get full updates as a result
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge page ref overflow branch.
Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).
Admittedly it's not exactly easy. To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers. Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).
Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication. So let's just do that.
* branch page-refs:
fs: prevent page refcount overflow in pipe_buf_get
mm: prevent get_user_pages() from overflowing page refcount
mm: add 'try_get_page()' helper function
mm: make page ref count overflow check tighter and more explicit
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub forgot to either use nlmsg_len() or nlmsg_msg_size(),
allowing KMSAN to detect a possible uninit-value in rtnl_stats_get
BUG: KMSAN: uninit-value in rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
CPU: 0 PID: 10428 Comm: syz-executor034 Not tainted 5.1.0-rc2+ #24
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x131/0x2a0 mm/kmsan/kmsan.c:619
__msan_warning+0x7a/0xf0 mm/kmsan/kmsan_instr.c:310
rtnl_stats_get+0x6d9/0x11d0 net/core/rtnetlink.c:4997
rtnetlink_rcv_msg+0x115b/0x1550 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
___sys_sendmsg+0xdb3/0x1220 net/socket.c:2137
__sys_sendmsg net/socket.c:2175 [inline]
__do_sys_sendmsg net/socket.c:2184 [inline]
__se_sys_sendmsg+0x305/0x460 net/socket.c:2182
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2182
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
Fixes: 51bc860d4a ("rtnetlink: stats: validate attributes in get as well as dumps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mikhail reported a lockdep splat related to the AMD specific ssb_state
lock:
CPU0 CPU1
lock(&st->lock);
local_irq_disable();
lock(&(&sighand->siglock)->rlock);
lock(&st->lock);
<Interrupt>
lock(&(&sighand->siglock)->rlock);
*** DEADLOCK ***
The connection between sighand->siglock and st->lock comes through seccomp,
which takes st->lock while holding sighand->siglock.
Make sure interrupts are disabled when __speculation_ctrl_update() is
invoked via prctl() -> speculation_ctrl_update(). Add a lockdep assert to
catch future offenders.
Fixes: 1f50ddb4f4 ("x86/speculation: Handle HT correctly on AMD")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Cc: Thomas Lendacky <thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1904141948200.4917@nanos.tec.linutronix.de
Denis Bolotin says:
====================
qed: Fix the Doorbell Overflow Recovery mechanism
This patch series fixes and improves the doorbell recovery mechanism.
The main goals of this series are to fix missing attentions from the
doorbells block (DORQ) or not handling them properly, and execute the
recovery from periodic handler instead of the attention handler.
Please consider applying the series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the page refcount wraps around past zero, it will be freed while
there are still four billion references to it. One of the possible
avenues for an attacker to try to make this happen is by doing direct IO
on a page multiple times. This patch makes get_user_pages() refuse to
take a new page reference if there are already more than two billion
references to the page.
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe". It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).
Also like 'get_page()', you can't use this function unless you already
had a reference to the page. The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.
The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.
NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.
That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).
Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When cache allocation is supported and the user creates a new resctrl
resource group, the allocations of the new resource group are
initialized to all regions that it can possibly use. At this time these
regions are all that are shareable by other resource groups as well as
regions that are not currently used. The new resource group's mode is
also initialized to reflect this initialization and set to "shareable".
The new resource group's mode is currently repeatedly initialized within
the loop that configures the hardware with the resource group's default
allocations.
Move the initialization of the resource group's mode outside the
hardware configuration loop. The resource group's mode is now
initialized only once as the final step to reflect that its configured
allocations are "shareable".
Fixes: 95f0b77efa ("x86/intel_rdt: Initialize new resource group with sane defaults")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pei.p.jia@intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1554839629-5448-1-git-send-email-xiaochen.shen@intel.com
Since the fget/fput handling was reworked in commit 09bb839434, we
never call io_file_put() with state == NULL (and hence file != NULL)
anymore. Remove that case.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A previous commit moved the shallow depth and BFQ depth map calculations
to be done at init time, moving it outside of the hotter IO path. This
potentially causes hangs if the users changes the depth of the scheduler
map, by writing to the 'nr_requests' sysfs file for that device.
Add a blk-mq-sched hook that allows blk-mq to inform the scheduler if
the depth changes, so that the scheduler can update its internal state.
Tested-by: Kai Krakow <kai@kaishome.de>
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Fixes: f0635b8a41 ("bfq: calculate shallow depths at init time")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently call cpu_possible() even if we don't use the CPU. Move the
test under the SQ_AFF branch, which is the only place where we'll use
the value. Do the cpu_possible() test AFTER we've limited it to a max
of NR_CPUS. This avoids triggering the following warning:
WARNING: CPU: 1 PID: 7600 at include/linux/cpumask.h:121 cpu_max_bits_warn
if CONFIG_DEBUG_PER_CPU_MAPS is enabled.
While in there, also move the SQ thread idle period assignment inside
SETUP_SQPOLL, as we don't use it otherwise either.
Reported-by: syzbot+cd714a07c6de2bc34293@syzkaller.appspotmail.com
Fixes: 6c271ce2f1 ("io_uring: add submission polling")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block fixes from Jens Axboe:
"Set of fixes that should go into this round. This pull is larger than
I'd like at this time, but there's really no specific reason for that.
Some are fixes for issues that went into this merge window, others are
not. Anyway, this contains:
- Hardware queue limiting for virtio-blk/scsi (Dongli)
- Multi-page bvec fixes for lightnvm pblk
- Multi-bio dio error fix (Jason)
- Remove the cache hint from the io_uring tool side, since we didn't
move forward with that (me)
- Make io_uring SETUP_SQPOLL root restricted (me)
- Fix leak of page in error handling for pc requests (Jérôme)
- Fix BFQ regression introduced in this merge window (Paolo)
- Fix break logic for bio segment iteration (Ming)
- Fix NVMe cancel request error handling (Ming)
- NVMe pull request with two fixes (Christoph):
- fix the initial CSN for nvme-fc (James)
- handle log page offsets properly in the target (Keith)"
* tag 'for-linus-20190412' of git://git.kernel.dk/linux-block:
block: fix the return errno for direct IO
nvmet: fix discover log page when offsets are used
nvme-fc: correct csn initialization and increments on error
block: do not leak memory in bio_copy_user_iov()
lightnvm: pblk: fix crash in pblk_end_partial_read due to multipage bvecs
nvme: cancel request synchronously
blk-mq: introduce blk_mq_complete_request_sync()
scsi: virtio_scsi: limit number of hw queues by nr_cpu_ids
virtio-blk: limit number of hw queues by nr_cpu_ids
block, bfq: fix use after free in bfq_bfqq_expire
io_uring: restrict IORING_SETUP_SQPOLL to root
tools/io_uring: remove IOCQE_FLAG_CACHEHIT
block: don't use for-inside-for in bio_for_each_segment_all
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fix:
- Fix a deadlock in close() due to incorrect draining of RDMA queues
Bugfixes:
- Revert "SUNRPC: Micro-optimise when the task is known not to be
sleeping" as it is causing stack overflows
- Fix a regression where NFSv4 getacl and fs_locations stopped
working
- Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
- Fix xfstests failures due to incorrect copy_file_range() return
values"
* tag 'nfs-for-5.1-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
Revert "SUNRPC: Micro-optimise when the task is known not to be sleeping"
NFSv4.1 fix incorrect return value in copy_file_range
xprtrdma: Fix helper that drains the transport
NFS: Fix handling of reply page vector
NFS: Forbid setting AF_INET6 to "struct sockaddr_in"->sin_family.
Pull SCSI fix from James Bottomley:
"One obvious fix for a ciostor data corruption on error bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: csiostor: fix missing data copy in csio_scsi_err_handler()
Pull clk fixes from Stephen Boyd:
"Here's more than a handful of clk driver fixes for changes that came
in during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Fix PLL_1416X not rounding rates
clk: mediatek: fix clk-gate flag setting
platform/x86: pmc_atom: Drop __initconst on dmi table
clk: x86: Add system specific quirk to mark clocks as critical
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
clk: at91: fix programmable clock for sama5d2
Pull PCI fixes from Bjorn Helgaas:
- Add a DMA alias quirk for another Marvell SATA device (Andre
Przywara)
- Fix a pciehp regression that broke safe removal of devices (Sergey
Miroshnichenko)
* tag 'pci-v5.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Ignore Link State Changes after powering off a slot
PCI: Add function 1 DMA alias quirk for Marvell 9170 SATA controller
Pull powerpc fixes from Michael Ellerman:
"A minor build fix for 64-bit FLATMEM configs.
A fix for a boot failure on 32-bit powermacs.
My commit to fix CLOCK_MONOTONIC across Y2038 broke the 32-bit VDSO on
64-bit kernels, ie. compat mode, which is only used on big endian.
The rewrite of the SLB code we merged in 4.20 missed the fact that the
0x380 exception is also used with the Radix MMU to report out of range
accesses. This could lead to an oops if userspace tried to read from
addresses outside the user or kernel range.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Larry Finger, Nicholas
Piggin"
* tag 'powerpc-5.1-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Define MAX_PHYSMEM_BITS for all 64-bit configs
powerpc/64s/radix: Fix radix segment exception handling
powerpc/vdso32: fix CLOCK_MONOTONIC on PPC64
powerpc/32: Fix early boot failure with RTAS built-in
Pull arm64 fixes from Will Deacon:
"The main thing is a fix to our FUTEX_WAKE_OP implementation which was
unbelievably broken, but did actually work for the one scenario that
GLIBC used to use.
Summary:
- Fix stack unwinding so we ignore user stacks
- Fix ftrace module PLT trampoline initialisation checks
- Fix terminally broken implementation of FUTEX_WAKE_OP atomics"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: futex: Fix FUTEX_WAKE_OP atomic ops with non-zero result value
arm64: backtrace: Don't bother trying to unwind the userspace stack
arm64/ftrace: fix inadvertent BUG() in trampoline check
We can receive ICMP errors from client or from
tunneling real server. While the former can be
scheduled to real server, the latter should
not be scheduled, they are decapsulated only when
existing connection is found.
Fixes: 6044eeffaf ("ipvs: attempt to schedule icmp packets")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Luca Moro says:
------
The issue lies in the filtering of ICMP and ICMPv6 errors that include an
inner IP datagram.
For these packets, icmp_error_message() extract the ICMP error and inner
layer to search of a known state.
If a state is found the packet is tagged as related (IP_CT_RELATED).
The problem is that there is no correlation check between the inner and
outer layer of the packet.
So one can encapsulate an error with an inner layer matching a known state,
while its outer layer is directed to a filtered host.
In this case the whole packet will be tagged as related.
This has various implications from a rule bypass (if a rule to related
trafic is allow), to a known state oracle.
Unfortunately, we could not find a real statement in a RFC on how this case
should be filtered.
The closest we found is RFC5927 (Section 4.3) but it is not very clear.
A possible fix would be to check that the inner IP source is the same than
the outer destination.
We believed this kind of attack was not documented yet, so we started to
write a blog post about it.
You can find it attached to this mail (sorry for the extract quality).
It contains more technical details, PoC and discussion about the identified
behavior.
We discovered later that
https://www.gont.com.ar/papers/filtering-of-icmp-error-messages.pdf
described a similar attack concept in 2004 but without the stateful
filtering in mind.
-----
This implements above suggested fix:
In icmp(v6) error handler, take outer destination address, then pass
that into the common function that does the "related" association.
After obtaining the nf_conn of the matching inner-headers connection,
check that the destination address of the opposite direction tuple
is the same as the outer address and only set RELATED if thats the case.
Reported-by: Luca Moro <luca.moro@synacktiv.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When an icmp error such as pkttoobig is received, conntrack checks
if the "inner" header (header of packet that did not fit link mtu)
is matches an existing connection, and, if so, sets that packet as
being related to the conntrack entry it found.
It was recently reported that this "related" setting also works
if the inner header is from another, different connection (i.e.,
artificial/forged icmp error).
Add a test, followup patch will add additional "inner dst matches
outer dst in reverse direction" check before setting related state.
Link: https://www.synacktiv.com/posts/systems/icmp-reachable.html
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The recent commit 98081ca62c ("ALSA: hda - Record the current power
state before suspend/resume calls") made the HD-audio driver to store
the PM state in power_state field. This forgot, however, the
initialization at power up. Although the codec drivers usually don't
need to refer to this field in the normal operation, let's initialize
it properly for consistency.
Fixes: 98081ca62c ("ALSA: hda - Record the current power state before suspend/resume calls")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The in-kernel afs filesystem client counts the number of server-level
callback invalidation events (CB.InitCallBackState* RPC operations) that it
receives from the server. This is stored in cb_s_break in various
structures, including afs_server and afs_vnode.
If an inode is examined by afs_validate(), say, the afs_server copy is
compared, along with other break counters, to those in afs_vnode, and if
one or more of the counters do not match, it is considered that the
server's callback promise is broken. At points where this happens,
AFS_VNODE_CB_PROMISED is cleared to indicate that the status must be
refetched from the server.
afs_validate() issues an FS.FetchStatus operation to get updated metadata -
and based on the updated data_version may invalidate the pagecache too.
However, the break counters are also used to determine whether to note a
new callback in the vnode (which would set the AFS_VNODE_CB_PROMISED flag)
and whether to cache the permit data included in the YFSFetchStatus record
by the server.
The problem comes when the server sends us a CB.InitCallBackState op. The
first such instance doesn't cause cb_s_break to be incremented, but rather
causes AFS_SERVER_FL_NEW to be cleared - but thereafter, say some hours
after last use and all the volumes have been automatically unmounted and
the server has forgotten about the client[*], this *will* likely cause an
increment.
[*] There are other circumstances too, such as the server restarting or
needing to make space in its callback table.
Note that the server won't send us a CB.InitCallBackState op until we talk
to it again.
So what happens is:
(1) A mount for a new volume is attempted, a inode is created for the root
vnode and vnode->cb_s_break and AFS_VNODE_CB_PROMISED aren't set
immediately, as we don't have a nominated server to talk to yet - and
we may iterate through a few to find one.
(2) Before the operation happens, afs_fetch_status(), say, notes in the
cursor (fc.cb_break) the break counter sum from the vnode, volume and
server counters, but the server->cb_s_break is currently 0.
(3) We send FS.FetchStatus to the server. The server sends us back
CB.InitCallBackState. We increment server->cb_s_break.
(4) Our FS.FetchStatus completes. The reply includes a callback record.
(5) xdr_decode_AFSCallBack()/xdr_decode_YFSCallBack() check to see whether
the callback promise was broken by checking the break counter sum from
step (2) against the current sum.
This fails because of step (3), so we don't set the callback record
and, importantly, don't set AFS_VNODE_CB_PROMISED on the vnode.
This does not preclude the syscall from progressing, and we don't loop here
rechecking the status, but rather assume it's good enough for one round
only and will need to be rechecked next time.
(6) afs_validate() it triggered on the vnode, probably called from
d_revalidate() checking the parent directory.
(7) afs_validate() notes that AFS_VNODE_CB_PROMISED isn't set, so doesn't
update vnode->cb_s_break and assumes the vnode to be invalid.
(8) afs_validate() needs to calls afs_fetch_status(). Go back to step (2)
and repeat, every time the vnode is validated.
This primarily affects volume root dir vnodes. Everything subsequent to
those inherit an already incremented cb_s_break upon mounting.
The issue is that we assume that the callback record and the cached permit
information in a reply from the server can't be trusted after getting a
server break - but this is wrong since the server makes sure things are
done in the right order, holding up our ops if necessary[*].
[*] There is an extremely unlikely scenario where a reply from before the
CB.InitCallBackState could get its delivery deferred till after - at
which point we think we have a promise when we don't. This, however,
requires unlucky mass packet loss to one call.
AFS_SERVER_FL_NEW tries to paper over the cracks for the initial mount from
a server we've never contacted before, but this should be unnecessary.
It's also further insulated from the problem on an initial mount by
querying the server first with FS.GetCapabilities, which triggers the
CB.InitCallBackState.
Fix this by
(1) Remove AFS_SERVER_FL_NEW.
(2) In afs_calc_vnode_cb_break(), don't include cb_s_break in the
calculation.
(3) In afs_cb_is_broken(), don't include cb_s_break in the check.
Signed-off-by: David Howells <dhowells@redhat.com>
__pagevec_release() complains loudly if any page in the vector is still
locked. The pages need to be locked for generic_error_remove_page(), but
that function doesn't actually unlock them.
Unlock the pages afterwards.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Differentiate an abort due to an unmarshalling error from an abort due to
other errors, such as ENETUNREACH. It doesn't make sense to set abort code
RXGEN_*_UNMARSHAL in such a case, so use RX_USER_ABORT instead.
Signed-off-by: David Howells <dhowells@redhat.com>
get_seconds() has a limited range on 32-bit architectures and is
deprecated because of that. While AFS uses the same limits for
its inode timestamps on the wire protocol, let's just use the
simpler current_time() as we do for other file systems.
This will still zero out the 'tv_nsec' field of the timestamps
internally.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Pull x86 fixes from Ingo Molnar:
"Fix typos in user-visible resctrl parameters, and also fix assembly
constraint bugs that might result in miscompilation"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Use stricter assembly constraints in bitops
x86/resctrl: Fix typos in the mba_sc mount option
Pull timer fix from Ingo Molnar:
"Fix the alarm_timer_remaining() return value"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Return correct remaining time
Pull scheduler fix from Ingo Molnar:
"Fix a NULL pointer dereference crash in certain environments"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Do not re-read ->h_load_next during hierarchical load calculation
Pull perf fixes from Ingo Molnar:
"Six kernel side fixes: three related to NMI handling on AMD systems, a
race fix, a kexec initialization fix and a PEBS sampling fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix perf_event_disable_inatomic() race
x86/perf/amd: Remove need to check "running" bit in NMI handler
x86/perf/amd: Resolve NMI latency issues for active PMCs
x86/perf/amd: Resolve race condition when disabling PMC
perf/x86/intel: Initialize TFA MSR
perf/x86/intel: Fix handling of wakeup_events for multi-entry PEBS
Pull locking fix from Ingo Molnar:
"Fixes a crash when accessing /proc/lockdep"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Zap lock classes even with lock debugging disabled
Pull core fixes from Ingo Molnar:
"Fix an objtool warning plus fix a u64_to_user_ptr() macro expansion
bug"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Add rewind_stack_do_exit() to the noreturn list
linux/kernel.h: Use parentheses around argument in u64_to_user_ptr()
Recompile IP options since IPCB may not be valid anymore when
ipv4_link_failure is called from arp_error_report.
Refer to the commit 3da1ed7ac3 ("net: avoid use IPCB in cipso_v4_error")
and the commit before that (9ef6b42ad6) for a similar issue.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells says:
====================
rxrpc: Fixes
Here is a collection of fixes for rxrpc:
(1) rxrpc_error_report() needs to call sock_error() to clear the error
code from the UDP transport socket, lest it be unexpectedly revisited
on the next kernel_sendmsg() call. This has been causing all sorts of
weird effects in AFS as the effects have typically been felt by the
wrong RxRPC call.
(2) Allow a kernel user of AF_RXRPC to easily detect if an rxrpc call has
completed.
(3) Allow errors incurred by attempting to transmit data through the UDP
socket to get back up the stack to AFS.
(4) Make AFS use (2) to abort the synchronous-mode call waiting loop if
the rxrpc-level call completed.
(5) Add a missing tracepoint case for tracing abort reception.
(6) Fix detection and handling of out-of-order ACKs.
====================
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rxrpc packet serial number cannot be safely used to compute out of
order ack packets for several reasons:
1. The allocation of serial numbers cannot be assumed to imply the order
by which acks are populated and transmitted. In some rxrpc
implementations, delayed acks and ping acks are transmitted
asynchronously to the receipt of data packets and so may be transmitted
out of order. As a result, they can race with idle acks.
2. Serial numbers are allocated by the rxrpc connection and not the call
and as such may wrap independently if multiple channels are in use.
In any case, what matters is whether the ack packet provides new
information relating to the bounds of the window (the firstPacket and
previousPacket in the ACK data).
Fix this by discarding packets that appear to wind back the window bounds
rather than on serial number procession.
Fixes: 298bc15b20 ("rxrpc: Only take the rwind and mtu values from latest ACK")
Signed-off-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace received calls that are aborted due to a connection abort, typically
because of authentication failure. Without this, connection aborts don't
show up in the trace log.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the state of the rxrpc call backing an afs call in each iteration of
the call wait loop in case the rxrpc call has already been terminated at
the rxrpc layer.
Interrupt the wait loop and mark the afs call as complete if the rxrpc
layer call is complete.
There were cases where rxrpc errors were not passed up to afs, which could
result in this loop waiting forever for an afs call to transition to
AFS_CALL_COMPLETE while the rx call was already complete.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change rxrpc_queue_packet()'s signature so that it can return any error
code it may encounter when trying to send the packet.
This allows the caller to eventually do something in case of error - though
it should be noted that the packet has been queued and a resend is
scheduled.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rxrpc_kernel_check_life() pass back the life counter through the
argument list and return true if the call has not yet completed.
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ICMP or ICMPV6 error is received, the error will be attached
to the socket (sk_err) and the report function will get called.
Clear any pending error here by calling sock_error().
This would cause the following attempt to use the socket to fail with
the error code stored by the ICMP error, resulting in unexpected errors
with various side effects depending on the context.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jonathan Billings <jsbillin@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975a ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279 ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Second batch of iwlwifi fixes intended for v5.1
* fix for a potential deadlock in the TX path;
* a fix for offloaded rate-control;
* support new PCI HW IDs which use a new FW;
Currently rt2x00 devices retransmit the management frames with
incremented sequence number if hardware is assigning the sequence.
This is HW bug fixed already for non-QOS data frames, but it should
be fixed for management frames except beacon.
Without fix retransmitted frames have wrong SN:
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1648, FN=0, Flags=........C Frame is not being retransmitted 1648 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1649, FN=0, Flags=....R...C Frame is being retransmitted 1649 1
AlphaNet_e8:fb:36 Vivotek_52:31:51 Authentication, SN=1650, FN=0, Flags=....R...C Frame is being retransmitted 1650 1
With the fix SN stays correctly the same:
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=........C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
88:6a:e3:e8:f9:a2 8c:f5:a3:88:76:87 Authentication, SN=1450, FN=0, Flags=....R...C
Cc: stable@vger.kernel.org
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
[sgruszka: simplify code, change comments and changelog]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that the sequence number allocation is fixed, we can finally send a BAR
at powersave wakeup time to refresh the receiver side reorder window
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the MT_TXD3_SN_VALID flag is not set in the tx descriptor, the hardware
assigns the sequence number. However, the rest of the code assumes that the
sequence number specified in the 802.11 header gets transmitted.
This was causing issues with the aggregation setup, which worked for the
initial one (where the sequence numbers were still close), but not for
further teardown/re-establishing of sessions.
Additionally, the overwrite of the TID sequence number in WTBL2 was resetting
the hardware assigned sequence numbers, causing them to drift further apart.
Fix this by using the software assigned sequence numbers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
KMSAN will complain if valid address length passed to udpv6_pre_connect()
is shorter than sizeof("struct sockaddr"->sa_family) bytes.
(This patch is bogus if it is guaranteed that udpv6_pre_connect() is
always called after checking "struct sockaddr"->sa_family. In that case,
we want a comment why we don't need to check valid address length here.)
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bpf_bind() is
shorter than sizeof("struct sockaddr"->sa_family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_llc) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_sco) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_rxrpc) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof(struct sockaddr_nl) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof("struct sockaddr_mISDN"->family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
shadow was added into shadow_list by amdgpu_bo_create_shadow.
meanwhile, shadow->tbo.mem was not fully configured.
tbo.mem would be fully configured by amdgpu_vm_sdma_map_table until calling amdgpu_vm_clear_bo.
If sriov TDR occurred between amdgpu_bo_create_shadow and amdgpu_vm_sdma_map_table,
amdgpu_device_recover_vram would deal with shadow without tbo.mem.start.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull dma-mapping fixes from Christoph Hellwig:
"Fix a sparc64 sun4v_pci regression introduced in this merged window,
and a dma-debug stracktrace regression from the big refactor last
merge window"
* tag 'dma-mapping-5.1-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: only skip one stackframe entry
sparc64/pci_sun4v: fix ATU checks for large DMA masks
Pull IOMMU fix from Joerg Roedel:
"Fix an AMD IOMMU issue where the driver didn't correctly setup the
exclusion range in the hardware registers, resulting in exclusion
ranges being one page too big.
This can cause data corruption of the address of that last page is
used by DMA operations"
* tag 'iommu-fix-v5.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Set exclusion range correctly
Pull clang-format update from Miguel Ojeda:
"The usual roughly-per-release .clang-format macro list update"
* tag 'clang-format-for-linus-v5.1-rc5' of git://github.com/ojeda/linux:
clang-format: Update with the latest for_each macro list
Pull MMC host fixes from Ulf Hansson:
- alcor: Stabilize data write requests
- sdhci-omap: Fix command error path during tuning
* tag 'mmc-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-omap: Don't finish_mrq() on a command error during tuning
mmc: alcor: don't write data before command has completed
Pull sound fixes from Takashi Iwai:
"Well, this one became unpleasantly larger than previous pull requests,
but it's a kind of usual pattern: now it contains a collection of ASoC
fixes, and nothing to worry too much.
The fixes for ASoC core (DAPM, DPCM, topology) are all small and just
covering corner cases. The rest changes are driver-specific, many of
which are for x86 platforms and new drivers like STM32, in addition to
the usual fixups for HD-audio"
* tag 'sound-5.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (66 commits)
ASoC: wcd9335: Fix missing regmap requirement
ALSA: hda: Fix racy display power access
ASoC: pcm: fix error handling when try_module_get() fails.
ASoC: stm32: sai: fix master clock management
ASoC: Intel: kbl: fix wrong number of channels
ALSA: hda - Add two more machines to the power_save_blacklist
ASoC: pcm: update module refcount if module_get_upon_open is set
ASoC: core: conditionally increase module refcount on component open
ASoC: stm32: fix sai driver name initialisation
ASoC: topology: Use the correct dobj to free enum control values and texts
ALSA: seq: Fix OOB-reads from strlcpy
ASoC: intel: skylake: add remove() callback for component driver
ASoC: cs35l35: Disable regulators on driver removal
ALSA: xen-front: Do not use stream buffer size before it is set
ASoC: rockchip: pdm: change dma burst to 8
ASoC: rockchip: pdm: fix regmap_ops hang issue
ASoC: simple-card: don't select DPCM via simple-audio-card
ASoC: audio-graph-card: don't select DPCM via audio-graph-card
ASoC: tlv320aic32x4: Change author's name
ALSA: hda/realtek - Add quirk for Tuxedo XC 1509
...
Pull ACPI fix from Rafael Wysocki:
"Fix an ACPICA issue introduced during the 4.20 development cycle and
causing some systems to crash because of leftover operation region
data still maintained after the operation region in question has gone
away (Erik Schmauss)"
* tag 'acpi-5.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Namespace: remove address node from global list after method termination
Pull drm fixes from Dave Airlie:
"Fixes across the driver spectrum this week, the mediatek fbdev support
might be a bit late for this round, but I looked over it and it's not
very large and seems like a useful feature for them.
Otherwise the main thing is a regression fix for i915 5.0 bug that
caused black screens on a bunch of Dell XPS 15s I think, I know at
least Fedora is waiting for this to land, and the udl fix is also for
a regression since 5.0 where unplugging the device would end badly.
core:
- make atomic hooks optional
i915:
- Revert a 5.0 regression where some eDP panels stopped working
- DSI related fixes for platforms up to IceLake
- GVT (regression fix, warning fix, use-after free fix)
amdgpu:
- Cursor fixes
- missing PCI ID fix for KFD
- XGMI fix
- shadow buffer handling after reset fix
udl:
- fix unplugging device crashes.
mediatek:
- stabilise MT2701 HDMI support
- fbdev support
tegra:
- fix for build regression in rc1.
sun4i:
- Allwinner A6 max freq improvements
- null ptr deref fix
dw-hdmi:
- SCDC configuration improvements
omap:
- CEC clock management policy fix"
* tag 'drm-fixes-2019-04-12' of git://anongit.freedesktop.org/drm/drm: (32 commits)
gpu: host1x: Fix compile error when IOMMU API is not available
drm/i915/gvt: Roundup fb->height into tile's height at calucation fb->size
drm/i915/dp: revert back to max link rate and lane count on eDP
drm/i915/icl: Fix port disable sequence for mipi-dsi
drm/i915/icl: Ungate ddi clocks before IO enable
drm/mediatek: no change parent rate in round_rate() for MT2701 hdmi phy
drm/mediatek: using new factor for tvdpll for MT2701 hdmi phy
drm/mediatek: remove flag CLK_SET_RATE_PARENT for MT2701 hdmi phy
drm/mediatek: make implementation of recalc_rate() for MT2701 hdmi phy
drm/mediatek: fix the rate and divder of hdmi phy for MT2701
drm/mediatek: fix possible object reference leak
drm/i915: Get power refs in encoder->get_power_domains()
drm/i915: Fix pipe_bpp readout for BXT/GLK DSI
drm/amd/display: Fix negative cursor pos programming (v2)
drm/sun4i: tcon top: Fix NULL/invalid pointer dereference in sun8i_tcon_top_un/bind
drm/udl: add a release method and delay modeset teardown
drm/i915/gvt: Prevent use-after-free in ppgtt_free_all_spt()
drm/i915/gvt: Annotate iomem usage
drm/sun4i: DW HDMI: Lower max. supported rate for H6
Revert "Documentation/gpu/meson: Remove link to meson_canvas.c"
...
Rather embarrassingly, our futex() FUTEX_WAKE_OP implementation doesn't
explicitly set the return value on the non-faulting path and instead
leaves it holding the result of the underlying atomic operation. This
means that any FUTEX_WAKE_OP atomic operation which computes a non-zero
value will be reported as having failed. Regrettably, I wrote the buggy
code back in 2011 and it was upstreamed as part of the initial arm64
support in 2012.
The reasons we appear to get away with this are:
1. FUTEX_WAKE_OP is rarely used and therefore doesn't appear to get
exercised by futex() test applications
2. If the result of the atomic operation is zero, the system call
behaves correctly
3. Prior to version 2.25, the only operation used by GLIBC set the
futex to zero, and therefore worked as expected. From 2.25 onwards,
FUTEX_WAKE_OP is not used by GLIBC at all.
Fix the implementation by ensuring that the return value is either 0
to indicate that the atomic operation completed successfully, or -EFAULT
if we encountered a fault when accessing the user mapping.
Cc: <stable@kernel.org>
Fixes: 6170a97460 ("arm64: Atomic operations")
Signed-off-by: Will Deacon <will.deacon@arm.com>
The exlcusion range limit register needs to contain the
base-address of the last page that is part of the range, as
bits 0-11 of this register are treated as 0xfff by the
hardware for comparisons.
So correctly set the exclusion range in the hardware to the
last page which is _in_ the range.
Fixes: b2026aa2dc ('x86, AMD IOMMU: add functions for programming IOMMU MMIO space')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Re-run the shell fragment that generated the original list now that
there are two dozens of new entries after v5.1's merge window.
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Thomas-Mich Richter reported he triggered a WARN()ing from event_function_local()
on his s390. The problem boils down to:
CPU-A CPU-B
perf_event_overflow()
perf_event_disable_inatomic()
@pending_disable = 1
irq_work_queue();
sched-out
event_sched_out()
@pending_disable = 0
sched-in
perf_event_overflow()
perf_event_disable_inatomic()
@pending_disable = 1;
irq_work_queue(); // FAILS
irq_work_run()
perf_pending_event()
if (@pending_disable)
perf_event_disable_local(); // WHOOPS
The problem exists in generic, but s390 is particularly sensitive
because it doesn't implement arch_irq_work_raise(), nor does it call
irq_work_run() from it's PMU interrupt handler (nor would that be
sufficient in this case, because s390 also generates
perf_event_overflow() from pmu::stop). Add to that the fact that s390
is a virtual architecture and (virtual) CPU-A can stall long enough
for the above race to happen, even if it would self-IPI.
Adding a irq_work_sync() to event_sched_in() would work for all hardare
PMUs that properly use irq_work_run() but fails for software PMUs.
Instead encode the CPU number in @pending_disable, such that we can
tell which CPU requested the disable. This then allows us to detect
the above scenario and even redirect the IPI to make up for the failed
queue.
Reported-by: Thomas-Mich Richter <tmricht@linux.ibm.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After commit e21db6f69a ("tcp: track total bytes delivered with ECN CE marks")
core TCP stack does a very good job tracking ECN signals.
The "sender's best estimate of CE information" Yuchung mentioned in his
patch is indeed the best we can do.
DCTCP can use tp->delivered_ce and tp->delivered to not duplicate the logic,
and use the existing best estimate.
This solves some problems, since current DCTCP logic does not deal with losses
and/or GRO or ack aggregation very well.
This also removes a dubious use of inet_csk(sk)->icsk_ack.rcv_mss
(this should have been tp->mss_cache), and a 64 bit divide.
Finally, we can see that the DCTCP logic, calling dctcp_update_alpha() for
every ACK could be done differently, calling it only once per RTT.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Abdul Kabbani <akabbani@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Revert back to max link rate and lane count on eDP.
- DSI related fixes for all platforms including Ice Lake.
- GVT Fixes including one vGPU display plane size regression fix,
one for preventing use-after-free in ppgtt shadow free function,
and another warning fix for iomem access annotation.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190411235832.GA6476@intel.com
If the last bio returned is not dio->bio, the status of the bio will
not assigned to dio->bio if it is error. This will cause the whole IO
status wrong.
ksoftirqd/21-117 [021] ..s. 4017.966090: 8,0 C N 4883648 [0]
<idle>-0 [018] ..s. 4017.970888: 8,0 C WS 4924800 + 1024 [0]
<idle>-0 [018] ..s. 4017.970909: 8,0 D WS 4935424 + 1024 [<idle>]
<idle>-0 [018] ..s. 4017.970924: 8,0 D WS 4936448 + 321 [<idle>]
ksoftirqd/21-117 [021] ..s. 4017.995033: 8,0 C R 4883648 + 336 [65475]
ksoftirqd/21-117 [021] d.s. 4018.001988: myprobe1: (blkdev_bio_end_io+0x0/0x168) bi_status=7
ksoftirqd/21-117 [021] d.s. 4018.001992: myprobe: (aio_complete_rw+0x0/0x148) x0=0xffff802f2595ad80 res=0x12a000 res2=0x0
We always have to assign bio->bi_status to dio->bio.bi_status because we
will only check dio->bio.bi_status when we return the whole IO to
the upper layer.
Fixes: 542ff7bf18 ("block: new direct I/O implementation")
Cc: stable@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull btrfs fixes from David Sterba:
- fix parsing of compression algorithm when set as a inode property,
this could end up with eg. 'zst' or 'zli' in the value
- don't allow trim on a filesystem with unreplayed log, this could
cause data loss if there are pending updates to the block groups that
would not be subject to trim after replay
* tag 'for-5.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: prop: fix vanished compression property after failed set
btrfs: prop: fix zstd compression parameter validation
Btrfs: do not allow trimming when a fs is mounted with the nologreplay option
A couple of tests are verifying a route has been removed. The helper
expects the prefix as the first part of the expected output. When
checking that a route has been deleted the prefix is empty leading
to an invalid ip command:
$ ip ro ls match
Command line is not complete. Try option "help"
Fix by moving the comparison of expected output and output to a new
function that is used by both check_route and check_route6. Use the
new helper for the 2 checks on route removal.
Also, remove the reset of 'set -x' in route_setup which overrides the
user managed setting.
Fixes: d69faad765 ("selftests: fib_tests: Add prefix route tests with metric")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this commit ded24019b6b6f(clocksource: arm_arch_timer: clean up
printk usage), the previous macro is redundant, so delete it.
And move the new macro to the previous position.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
When this is disabled, we get a link failure:
drivers/clocksource/timer-npcm7xx.o: In function `npcm7xx_timer_init':
timer-npcm7xx.c:(.init.text+0xf): undefined reference to `timer_of_init'
Fixes: 1c00289ecd ("clocksource/drivers/npcm: Add NPCM7xx timer driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This reverts commit 009a82f643.
The ability to optimise here relies on compiler being able to optimise
away tail calls to avoid stack overflows. Unfortunately, we are seeing
reports of problems, so let's just revert.
Reported-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
According to the NFSv4.2 spec if the input and output file is the
same file, operation should fail with EINVAL. However, linux
copy_file_range() system call has no such restrictions. Therefore,
in such case let's return EOPNOTSUPP and allow VFS to fallback
to doing do_splice_direct(). Also when copy_file_range is called
on an NFSv4.0 or 4.1 mount (ie., a server that doesn't support
COPY functionality), we also need to return EOPNOTSUPP and
fallback to a regular copy.
Fixes xfstest generic/075, generic/091, generic/112, generic/263
for all NFSv4.x versions.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
We want to drain only the RQ first. Otherwise the transport can
deadlock on ->close if there are outstanding Send completions.
Fixes: 6d2d0ee27c ("xprtrdma: Replace rpcrdma_receive_wq ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
NFSv4 GETACL and FS_LOCATIONS requests stopped working in v5.1-rc.
These two need the extra padding to be added directly to the reply
length.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: 02ef04e432 ("NFS: Account for XDR pad of buf->pages")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
syzbot is reporting uninitialized value at rpc_sockaddr2uaddr() [1]. This
is because syzbot is setting AF_INET6 to "struct sockaddr_in"->sin_family
(which is embedded into user-visible "struct nfs_mount_data" structure)
despite nfs23_validate_mount_data() cannot pass sizeof(struct sockaddr_in6)
bytes of AF_INET6 address to rpc_sockaddr2uaddr().
Since "struct nfs_mount_data" structure is user-visible, we can't change
"struct nfs_mount_data" to use "struct sockaddr_storage". Therefore,
assuming that everybody is using AF_INET family when passing address via
"struct nfs_mount_data"->addr, reject if its sin_family is not AF_INET.
[1] https://syzkaller.appspot.com/bug?id=599993614e7cbbf66bc2656a919ab2a95fb5d75c
Reported-by: syzbot <syzbot+047a11c361b872896a4f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06 ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce says:
====================
Fix thunderx MTU with XDP
The thunderx driver can't use XDP with all MTU values.
This patches sets the right MTU values, and add a check to avoid setting
a wrong value which will not function.
v3: Fix a copy-paste from two functions, tested on proper hardware:
2: enP2p1s0v0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 1c:1b:0d:0d:52:a4 brd ff:ff:ff:ff:ff:ff
[ 787.019730] nicvf 0002:01:00.1 enP2p1s0v0: Jumbo frames not yet supported with XDP, current MTU 1800.
RTNETLINK answers: Operation not supported
[ 800.574568] nicvf 0002:01:00.1 enP2p1s0v0: Link is Up 10000 Mbps Full duplex
[ 807.248321] nicvf 0002:01:00.1 enP2p1s0v0: Jumbo frames not yet supported with XDP, current MTU 1500.
RTNETLINK answers: Invalid argument
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: fixes 2019-04-11
here are some fixes in different areas of the smc code for the net
tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit <26d92e951fe0>
("net/smc: move unhash as early as possible in smc_release()")
fixes one occurrence in the smc code, but the same pattern exists
in other places. This patch covers the remaining occurrences and
makes sure, the unhash operation is done before the smc->clcsock is
released. This avoids a potential use-after-free in smc_diag_dump().
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLUSH command is used to empty the pnet table. No return code is
expected from the command. Commit a9d8b0b1e3d6 added namespace support
for the pnet table and changed the FLUSH command processing to call
smc_pnet_remove_by_pnetid() to remove the pnet entries. This function
returns -ENOENT when no entry was deleted, which is now the return code
of the FLUSH command. As a result the FLUSH command will return an error
when the pnet table is already empty.
Restore the expected behavior and let FLUSH always return 0.
Fixes: a9d8b0b1e3d6 ("net/smc: add pnet table namespace support")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fcntl(fd, F_SETOWN, getpid()) selects the recipient of SIGURG signals
that are delivered when out-of-band data arrives on socket fd.
If an SMC socket program makes use of such an fcntl() call, it fails
in case of fallback to TCP-mode. In case of fallback the traffic is
processed with the internal TCP socket. Propagating field "file" from the
SMC socket to the internal TCP socket fixes the issue.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case alloc_ordered_workqueue fails, the fix returns NULL
to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the clcsock is already released using sock_release() and a pending
smc_listen_work accesses the clcsock than that will fail. Solve this
by canceling and waiting for the work to complete first. Because the
work holds the sock_lock it must make sure that the lock is not hold
before the new helper smc_clcsock_release() is invoked. And before the
smc_listen_work starts working check if the parent listen socket is
still valid, otherwise stop the work early.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With skip set to 1, I get a traceback like this:
[ 106.867637] DMA-API: Mapped at:
[ 106.870784] afu_dma_map_region+0x2cd/0x4f0 [dfl_afu]
[ 106.875839] afu_ioctl+0x258/0x380 [dfl_afu]
[ 106.880108] do_vfs_ioctl+0xa9/0x720
[ 106.883688] ksys_ioctl+0x60/0x90
[ 106.887007] __x64_sys_ioctl+0x16/0x20
With the previous value of 2, afu_dma_map_region was being omitted. I
suspect that the code paths have simply changed since the value of 2 was
chosen a decade ago, but it's also possible that it varies based on which
mapping function was used, compiler inlining choices, etc. In any case,
it's best to err on the side of skipping less.
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It's used by probe and that isn't an init function. Drop this so that we
don't get a section mismatch.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: David Müller <dave.mueller@gmx.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: 7c2e071300 ("clk: x86: Add system specific quirk to mark clocks as critical")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If SMMU support is not available, fall back to programming the bypass
stream ID (0x7f).
Fixes: de5469c21f ("gpu: host1x: Program the channel stream ID")
Suggested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: rebase this on top of a later build fix]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull NVMe fixes from Christoph:
"Two nvme fixes for 5.1 - fixing the initial CSN for nvme-fc, and handle
log page offsets properly in the target."
* 'nvme-5.1' of git://git.infradead.org/nvme:
nvmet: fix discover log page when offsets are used
nvme-fc: correct csn initialization and increments on error
The nvme target hadn't been taking the Get Log Page offset parameter
into consideration, and so has been returning corrupted log pages when
offsets are used. Since many tools, including nvme-cli, split the log
request to 4k, we've been breaking discovery log responses when more
than 3 subsystems exist.
Fix the returned data by internally generating the entire discovery
log page and copying only the requested bytes into the user buffer. The
command log page offset type has been modified to a native __le64 to
make it easier to extract the value from a command.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes a long-standing bug that initialized the FC-NVME
cmnd iu CSN value to 1. Early FC-NVME specs had the connection starting
with CSN=1. By the time the spec reached approval, the language had
changed to state a connection should start with CSN=0. This patch
corrects the initialization value for FC-NVME connections.
Additionally, in reviewing the transport, the CSN value is assigned to
the new IU early in the start routine. It's possible that a later dma
map request may fail, causing the command to never be sent to the
controller. Change the location of the assignment so that it is
immediately prior to calling the lldd. Add a comment block to explain
the impacts if the lldd were to additionally fail sending the command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Why]
AUX takes longer to reply when using active DP-DVI dongle on some asics
resulting in up to 2000+ us edid read (timeout).
[How]
1. Adjust AUX poll to match spec
2. Extend the SW timeout. This does not affect normal
operation since we exit the loop as soon as AUX acks.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the ttm_bo_add_move_fence takes a reference to the struct dma_fence, but
failed to release it on the error path, leading to a memory leak.
add dma_fence_put before return when error occur.
Signed-off-by: Lin Yi <teroincn@163.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we increment the counter we need to increment the pointer as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: e16858a7e6e7 drm/ttm: fix start page for huge page check in ttm_put_pages()
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When ttm_put_pages() tries to figure out whether it's dealing with
transparent hugepages, it just reads past the bounds of the pages array
without a check.
v2: simplify the test if enough pages are left in the array (Christian).
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 5c42c64f7d ("drm/ttm: fix the fix for huge compound pages")
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When setting sync EIC as IRQ_TYPE_EDGE_BOTH type, we missed to set the
SPRD_EIC_SYNC_INTMODE register to 0, which means detecting edge signals.
Thus this patch fixes the issue.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ASoC: Fixes for v5.1
A few core fixes along with the driver specific ones, mainly fixing
small issues that only affect x86 platforms for various reasons (their
unusual machine enumeration mechanisms mainly, plus a fix for error
handling in topology).
There's some of the driver fixes that look larger than they are, like
the hdmi-codec changes which resulted in an indentation change, and most
of the other large changes are for new drivers like the STM32 changes.
commit 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback") skips data resets during tuning operation. Because of this,
a data error or data finish interrupt might still arrive after a command
error has been handled and the mrq ended. This ends up with a "mmc0: Got
data interrupt 0x00000002 even though no data operation was in progress"
error message.
Fix this by adding a platform specific callback for sdhci_irq. Mark the
mrq as a failure but wait for a data interrupt instead of calling
finish_mrq().
Fixes: 5b0d62108b ("mmc: sdhci-omap: Add platform specific reset
callback")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the IOMMU API is not available compiling host1x fails with
the following error:
In file included from drivers/gpu/host1x/hw/host1x06.c:27:
drivers/gpu/host1x/hw/channel_hw.c: In function ‘host1x_channel_set_streamid’:
drivers/gpu/host1x/hw/channel_hw.c:118:30: error: implicit declaration of function
‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(channel->dev->parent);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
Fixes: de5469c21f ("gpu: host1x: Program the channel stream ID")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
gue tunnels run iptunnel_pull_offloads on received skbs. This can
determine a possible use-after-free accessing guehdr pointer since
the packet will be 'uncloned' running pskb_expand_head if it is a
cloned gso skb (e.g if the packet has been sent though a veth device)
Fixes: a09a4c8dd1 ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding multiple services with specific type 1Ki, 2Ki..,
this leads to some entries in the name table of publications
missing when listed out via 'tipc name show'.
The problem is at identify zero last_type conditional provided
via netlink. The first is initial 'type' when starting name table
dummping. The second is continuously with zero type (node state
service type). Then, lookup function failure to finding node state
service type in next iteration.
To solve this, adding more conditional to marked as dirty type and
lookup correct service type for the next iteration instead of select
the first service as initial 'type' zero.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.
As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.
Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.
It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point. The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.
Fixes: 30c8bd5aa8 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fb is tiled and fb->height isn't the multiple of tile's height,
the format fb->size = fb->stride * fb->height, will get a smaller size
than the actual size. As the memory height of tiled fb should be multiple
of tile's height.
Fixes: 7f1a93b1f1 ("drm/i915/gvt: Correct the calculation of plane size")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
After adding a team interface to bridge, the team interface will enter
promisc mode. Then if we add a new slave to team0, the slave will keep
promisc off. Fix it by setting slave to promisc on if team master is
already in promisc mode, also do the same for allmulti.
v2: add promisc and allmulti checking when delete ports
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
buildbot noticed that TLS_HW is not defined if CONFIG_TLS_DEVICE=n.
Wrap the cleanup branch into an ifdef, tls_device_free_resources_tx()
wouldn't be compiled either in this case.
Fixes: 35b71a34ad ("net/tls: don't leak partially sent record in device mode")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 648e921888 ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the pmc_plt_clocks of the Bay Trail SoC are
unconditionally gated off. Unfortunately this will break systems where these
clocks are used for external purposes beyond the kernel's knowledge. Fix it
by implementing a system specific quirk to mark the necessary pmc_plt_clks as
critical.
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: David Müller <dave.mueller@gmx.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
During a safe hot remove, the OS powers off the slot, which may cause a
Data Link Layer State Changed event. The slot has already been set to
OFF_STATE, so that event results in re-enabling the device, making it
impossible to safely remove it.
Clear out the Presence Detect Changed and Data Link Layer State Changed
events when the disabled slot has settled down.
It is still possible to re-enable the device if it remains in the slot
after pressing the Attention Button by pressing it again.
Fixes the problem that Micah reported below: an NVMe drive power button may
not actually turn off the drive.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203237
Reported-by: Micah Parrish <micah.parrish@hpe.com>
Tested-by: Micah Parrish <micah.parrish@hpe.com>
Signed-off-by: Sergey Miroshnichenko <s.miroshnichenko@yadro.com>
[bhelgaas: changelog, add bugzilla URL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
Jakub Kicinski says:
====================
net: tls: fix memory leaks and freeing skbs
This series fixes two memory issues and a stack overflow.
First two patches are fairly simple leaks. Third patch
partially reverts an optimization made to the strparser
which causes creation of skb->frag_list->skb->frag_list...
chains of 100s of skbs, leading to recursive kfree_skb()
filling up the kernel stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the first part of commit 4e485d06bb ("strparser: Call
skb_unclone conditionally"). To build a message with multiple
fragments we need our own root of frag_list. We can't simply
use the frag_list of orig_skb, because it will lead to linking
all orig_skbs together creating very long frag chains, and causing
stack overflow on kfree_skb() (which is called recursively on
the frag_lists).
BUG: stack guard page was hit at 00000000d40fad41 (stack is 0000000029dde9f4..000000008cce03d5)
kernel stack overflow (double-fault): 0000 [#1] PREEMPT SMP
RIP: 0010:free_one_page+0x2b/0x490
Call Trace:
__free_pages_ok+0x143/0x2c0
skb_release_data+0x8e/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
[...]
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
? skb_release_data+0xad/0x140
kfree_skb+0x32/0xb0
skb_release_data+0xad/0x140
__kfree_skb+0xe/0x20
tcp_disconnect+0xd6/0x4d0
tcp_close+0xf4/0x430
? tcp_check_oom+0xf0/0xf0
tls_sk_proto_close+0xe4/0x1e0 [tls]
inet_release+0x36/0x60
__sock_release+0x37/0xa0
sock_close+0x11/0x20
__fput+0xa2/0x1d0
task_work_run+0x89/0xb0
exit_to_usermode_loop+0x9a/0xa0
do_syscall_64+0xc0/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Let's leave the second unclone conditional, as I'm not entirely
sure what is its purpose :)
Fixes: 4e485d06bb ("strparser: Call skb_unclone conditionally")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reports that tls triggers warnings related to
sk->sk_forward_alloc not being zero at destruction time:
WARNING: CPU: 5 PID: 6831 at net/core/stream.c:206 sk_stream_kill_queues+0x103/0x110
WARNING: CPU: 5 PID: 6831 at net/ipv4/af_inet.c:160 inet_sock_destruct+0x15b/0x170
When sender fills up the write buffer and dies from
SIGPIPE. This is due to the device implementation
not cleaning up the partially_sent_record.
This is because commit a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
moved the partial record cleanup to the SW-only path.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f66de3ee2c ("net/tls: Split conf to rx + tx") made
freeing of IV and record sequence number conditional to SW
path only, but commit e8f6979981 ("net/tls: Add generic NIC
offload infrastructure") also allocates that state for the
device offload configuration. Remember to free it.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we allow drivers to always need to set larger than required
DMA masks we need to be a little more careful in the sun4v PCI iommu
driver to chose when to select the ATU support - a larger DMA mask
can be set even when the platform does not support ATU, so we always
have to check if it is avaiable before using it. Add a little helper
for that and use it in all the places where we make ATU usage decisions
based on the DMA mask.
Fixes: 24132a419c ("sparc64/pci_sun4v: allow large DMA masks")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
Pull rdma fixes from Jason Gunthorpe:
"Several driver bug fixes posted in the last several weeks
- Several bug fixes for the hfi1 driver 'TID RDMA' functionality
merged into 5.1. Since TID RDMA is on by default these all seem to
be regressions.
- Wrong software permission checks on memory in mlx5
- Memory leak in vmw_pvrdma during driver remove
- Several bug fixes for hns driver features merged into 5.1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/hfi1: Do not flush send queue in the TID RDMA second leg
RDMA/hns: Bugfix for SCC hem free
RDMA/hns: Fix bug that caused srq creation to fail
RDMA/vmw_pvrdma: Fix memory leak on pvrdma_pci_remove
IB/mlx5: Reset access mask when looping inside page fault handler
IB/hfi1: Fix the allocation of RSM table
IB/hfi1: Eliminate opcode tests on mr deref
IB/hfi1: Clear the IOWAIT pending bits when QP is put into error state
IB/hfi1: Failed to drain send queue when QP is put into error state
Thomas Falcon says:
====================
ibmvnic: Fix netdev features settings on reset
In its current state, a driver reset clobbers any feature settings
a user may have toggled and will disable GRO as it is not explicitly
enabled in the driver. This patch set enables GRO and tries to retain
user settings after a reset. If the underlying carrier changes, however,
the driver will disable features unsupported by the new carrier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a patchwork instance behind bcm-kernel-feedback-list that is
helpful to track submissions, add this list for the MIPS BMIPS entry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Ido Schimmel says:
====================
mlxsw: Various fixes
This patchset contains various small fixes for mlxsw.
Patch #1 fixes a warning generated by switchdev core when the driver
fails to insert an MDB entry in the commit phase.
Patches #2-#4 fix a warning in check_flush_dependency() that can be
triggered when a work item in a WQ_MEM_RECLAIM workqueue tries to flush
a non-WQ_MEM_RECLAIM workqueue.
It seems that the semantics of the WQ_MEM_RECLAIM flag are not very
clear [1] and that various patches have been sent to remove it from
various workqueues throughout the kernel [2][3][4] in order to silence
the warning.
These patches do the same for the workqueues created by mlxsw that
probably should not have been created with this flag in the first place.
Patch #5 fixes a regression where an IP address cannot be assigned to a
VRF upper due to erroneous MAC validation check. Patch #6 adds a test
case.
Patch #7 adjusts Spectrum-2 shared buffer configuration to be compatible
with Spectrum-1. The problem and fix are described in detail in the
commit message.
Please consider patches #1-#5 for 5.0.y. I verified they apply cleanly.
[1] https://patchwork.kernel.org/patch/10791315/
[2] Commit ce162bfbc0 ("mac80211_hwsim: don't use WQ_MEM_RECLAIM")
[3] Commit 39baf10310 ("IB/core: Fix use workqueue without WQ_MEM_RECLAIM")
[4] Commit 75215e5bb2 ("iwcm: Don't allocate iwcm workqueue with WQ_MEM_RECLAIM")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that it is possible to set an IP address on a VRF and that it is
not vetoed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e920 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of multipage bio vectors broke pblk's partial read
logic due to it not being prepared for multipage bio vectors.
Use bio vector iterators instead of direct bio vector indexing.
Fixes: 07173c3ec2 ("block: enable multipage bvecs")
Reported-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Updated description.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a QP is put into error state, the send queue will be flushed.
This mechanism is implemented in both the first and the second leg
of the send engine. Since the second leg is only responsible for
data transactions in the KDETH space for the TID RDMA WRITE request,
it should not perform the flushing of the send queue.
This patch removes the flushing function of the second leg, but
still keeps the bailing out of the QP if it is put into error state.
Fixes: 70dcb2e3dc ("IB/hfi1: Add the TID second leg send packet builder")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pull virtio fixes from Michael Tsirkin:
"Several fixes, add more reviewers to the list"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: Honour 'may_reduce_num' in vring_create_virtqueue
MAiNTAINERS: add Paolo, Stefan for virtio blk/scsi
virtio_pci: fix a NULL pointer reference in vp_del_vqs
The Maximum Physical Memory 2GiB option for 64bit systems is currently
broken because kernel hangs at boot-time when this option is enabled
and the underlying system has more than 2GiB memory.
This issue can be easily reproduced on SiFive Unleashed board where
we have 8GiB of memory.
This patch fixes above issue by removing unusable memory region in
setup_bootmem().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
nvme_cancel_request() is used in error handler, and it is always
reliable to cancel request synchronously, and avoids possible race
in which request may be completed after real hw queue is destroyed.
One issue is reported by our customer on NVMe RDMA, in which freed ib
queue pair may be used in nvme_rdma_complete_rq().
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-nvme@lists.infradead.org
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In NVMe's error handler, follows the typical steps of tearing down
hardware for recovering controller:
1) stop blk_mq hw queues
2) stop the real hw queues
3) cancel in-flight requests via
blk_mq_tagset_busy_iter(tags, cancel_request, ...)
cancel_request():
mark the request as abort
blk_mq_complete_request(req);
4) destroy real hw queues
However, there may be race between #3 and #4, because blk_mq_complete_request()
may run q->mq_ops->complete(rq) remotelly and asynchronously, and
->complete(rq) may be run after #4.
This patch introduces blk_mq_complete_request_sync() for fixing the
above race.
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-nvme@lists.infradead.org
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With commit 01396a374c ("s390/zcrypt: revisit ap device remove
procedure") the ap queue remove is now a two stage process. However,
a del_timer_sync() call may trigger the timer function which may
try to lock the very same spinlock as is held by the function
just initiating the del_timer_sync() call. This could end up in
a deadlock situation. Very unlikely but possible as you need to
remove an ap queue at the exact sime time when a timeout of a
request occurs.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Pierre Morel <pmorel@linux.ibm.com>
Fixes: commit 01396a374c ("s390/zcrypt: revisit ap device remove procedure")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The spinlock in the raw3270_view structure is used by con3270, tty3270
and fs3270 in different ways. For con3270 the lock can be acquired in
irq context, for tty3270 and fs3270 the highest context is bh.
Lockdep sees the view->lock as a single class and if the 3270 driver
is used for the console the following message is generated:
WARNING: inconsistent lock state
5.1.0-rc3-05157-g5c168033979d #12 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
swapper/0/1 [HC0[0]:SC1[1]:HE1:SE0] takes:
(____ptrval____) (&(&view->lock)->rlock){?.-.}, at: tty3270_update+0x7c/0x330
Introduce a lockdep subclass for the view lock to distinguish bh from
irq locks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-scsi, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num_queues' specified
by qemu is more than maxcpus, virtio-scsi would not be able to allocate
more than maxcpus vectors in order to have a vector for each queue. As a
result, it falls back into MSI-X with one vector for config and one shared
for queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-scsi by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-blk, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num-queues' specified
by qemu is more than maxcpus, virtio-blk would not be able to allocate more
than maxcpus vectors in order to have a vector for each queue. As a result,
it falls back into MSI-X with one vector for config and one shared for
queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-blk by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function bfq_bfqq_expire() invokes the function
__bfq_bfqq_expire(), and the latter may free the in-service bfq-queue.
If this happens, then no other instruction of bfq_bfqq_expire() must
be executed, or a use-after-free will occur.
Basing on the assumption that __bfq_bfqq_expire() invokes
bfq_put_queue() on the in-service bfq-queue exactly once, the queue is
assumed to be freed if its refcounter is equal to one right before
invoking __bfq_bfqq_expire().
But, since commit 9dee8b3b05 ("block, bfq: fix queue removal from
weights tree") this assumption is false. __bfq_bfqq_expire() may also
invoke bfq_weights_tree_remove() and, since commit 9dee8b3b05
("block, bfq: fix queue removal from weights tree"), also
the latter function may invoke bfq_put_queue(). So __bfq_bfqq_expire()
may invoke bfq_put_queue() twice, and this is the actual case where
the in-service queue may happen to be freed.
To address this issue, this commit moves the check on the refcounter
of the queue right around the last bfq_put_queue() that may be invoked
on the queue.
Fixes: 9dee8b3b05 ("block, bfq: fix queue removal from weights tree")
Reported-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
snd_hdac_display_power() doesn't handle the concurrent calls carefully
enough, and it may lead to the doubly get_power or put_power calls,
when a runtime PM and an async work get called in racy way.
This patch addresses it by reusing the bus->lock mutex that has been
used for protecting the link state change in ext bus code, so that it
can protect against racy display state changes. The initialization of
bus->lock was moved from snd_hdac_ext_bus_init() to
snd_hdac_bus_init() as well accordingly.
Testcase: igt/i915_pm_rpm/module-reload #glk-dsi
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following commit:
a0b0fd53e1 ("locking/lockdep: Free lock classes that are no longer in use")
changed the behavior of lockdep_free_key_range() from
unconditionally zapping lock classes into only zapping lock classes if
debug_lock == true. Not zapping lock classes if debug_lock == false leaves
dangling pointers in several lockdep datastructures, e.g. lock_class::name
in the all_lock_classes list.
The shell command "cat /proc/lockdep" causes the kernel to iterate the
all_lock_classes list. Hence the "unable to handle kernel paging request" cash
that Shenghui encountered by running cat /proc/lockdep.
Since the new behavior can cause cat /proc/lockdep to crash, restore the
pre-v5.1 behavior.
This patch avoids that cat /proc/lockdep triggers the following crash
with debug_lock == false:
BUG: unable to handle kernel paging request at fffffbfff40ca448
RIP: 0010:__asan_load1+0x28/0x50
Call Trace:
string+0xac/0x180
vsnprintf+0x23e/0x820
seq_vprintf+0x82/0xc0
seq_printf+0x92/0xb0
print_name+0x34/0xb0
l_show+0x184/0x200
seq_read+0x59e/0x6c0
proc_reg_read+0x11f/0x170
__vfs_read+0x4d/0x90
vfs_read+0xc5/0x1f0
ksys_read+0xab/0x130
__x64_sys_read+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: shenghui <shhuiw@foxmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: a0b0fd53e1 ("locking/lockdep: Free lock classes that are no longer in use") # v5.1-rc1.
Link: https://lkml.kernel.org/r/20190403233552.124673-1-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Handle error before returning when try_module_get() fails
to prevent inconsistent mutex lock/unlock.
Fixes: 52034add7 (ASoC: pcm: update module refcount if
module_get_upon_open is set)
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before commit c5459b829b ("LSM: Plumb visibility into optional "enabled"
state"), /sys/module/apparmor/parameters/enabled would show "Y" or "N"
since it was using the "bool" handler. After being changed to "int",
this switched to "1" or "0", breaking the userspace AppArmor detection
of dbus-broker. This restores the Y/N output while keeping the LSM
infrastructure happy.
Before:
$ cat /sys/module/apparmor/parameters/enabled
1
After:
$ cat /sys/module/apparmor/parameters/enabled
Y
Reported-by: David Rheinsberg <david.rheinsberg@gmail.com>
Reviewed-by: David Rheinsberg <david.rheinsberg@gmail.com>
Link: https://lkml.kernel.org/r/CADyDSO6k8vYb1eryT4g6+EHrLCvb68GAbHVWuULkYjcZcYNhhw@mail.gmail.com
Fixes: c5459b829b ("LSM: Plumb visibility into optional "enabled" state")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>
When master clock is used, master clock rate is set exclusively.
Parent clocks of master clock cannot be changed after a call to
clk_set_rate_exclusive(). So the parent clock of SAI kernel clock
must be set before.
Ensure also that exclusive rate operations are balanced
in STM32 SAI driver.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Spurious interrupt support was added to perf in the following commit, almost
a decade ago:
63e6be6d98 ("perf, x86: Catch spurious interrupts after disabling counters")
The two previous patches (resolving the race condition when disabling a
PMC and NMI latency mitigation) allow for the removal of this older
spurious interrupt support.
Currently in x86_pmu_stop(), the bit for the PMC in the active_mask bitmap
is cleared before disabling the PMC, which sets up a race condition. This
race condition was mitigated by introducing the running bitmap. That race
condition can be eliminated by first disabling the PMC, waiting for PMC
reset on overflow and then clearing the bit for the PMC in the active_mask
bitmap. The NMI handler will not re-enable a disabled counter.
If x86_pmu_stop() is called from the perf NMI handler, the NMI latency
mitigation support will guard against any unhandled NMI messages.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The validation of random PID should be done by checking the
boardinfo->pid instead of info.pid which is empty.
Doing the change the info struture declaration is no longer necessary.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The recent commit 8bc0868998 ("powerpc/mm: Only define
MAX_PHYSMEM_BITS in SPARSEMEM configurations") removed our definition
of MAX_PHYSMEM_BITS when SPARSEMEM is disabled.
This inadvertently broke some 64-bit FLATMEM using configs with eg:
arch/powerpc/include/asm/book3s/64/mmu-hash.h:584:6: error: "MAX_PHYSMEM_BITS" is not defined, evaluates to 0
#if (MAX_PHYSMEM_BITS > MAX_EA_BITS_PER_CONTEXT)
^~~~~~~~~~~~~~~~
Fix it by making sure we define MAX_PHYSMEM_BITS for all 64-bit
configs regardless of SPARSEMEM.
Fixes: 8bc0868998 ("powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Reported-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Badly-designed systems might have (for example) active-high wake pins
that default to high (e.g., because of external pull ups) until they
have an active firmware which starts driving it low. This can cause an
interrupt storm in the time between request_irq() and disable_irq().
We don't support shared interrupts here, so let's just pre-configure the
interrupt to avoid auto-enabling it.
Fixes: fd913ef7ce ("Bluetooth: btusb: Add out-of-band wakeup support")
Fixes: 5364a0b4f4 ("arm64: dts: rockchip: move QCA6174A wakeup pin into its USB node")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS fixes from Paul Burton:
"A few minor MIPS fixes:
- Provide struct pt_regs * from get_irq_regs() to kgdb_nmicallback()
when handling an IPI triggered by kgdb_roundup_cpus(), matching the
behavior of other architectures & resolving kgdb issues for SMP
systems.
- Defer a pointer dereference until after a NULL check in the
irq_shutdown callback for SGI IP27 HUB interrupts.
- A defconfig update for the MSCC Ocelot to enable some necessary
drivers"
* tag 'mips_fixes_5.1_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: generic: Add switchdev, pinctrl and fit to ocelot_defconfig
MIPS: SGI-IP27: Fix use of unchecked pointer in shutdown_bridge_irq
MIPS: KGDB: fix kgdb support for SMP platforms.
Pull misc fixes from Al Viro:
"A few regression fixes from this cycle"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: use kmem_cache_free() instead of kfree()
iov_iter: Fix build error without CONFIG_CRYPTO
aio: Fix an error code in __io_submit_one()
Although XOR hash function can perform very well on some special use
cases, to align with all drivers, mlx5 driver should use Toeplitz hash
by default.
Toeplitz is more stable for the general use case and it is more standard
and reliable.
On top of that, since XOR (MLX5_RX_HASH_FN_INVERTED_XOR8) gives only a
repeated 8 bits pattern. When used for udp tunneling RSS source port
manipulation it results in fixed source port, which will cause bad RSS
spread.
Fixes: 2be6967cdb ("net/mlx5e: Support ETH_RSS_HASH_XOR")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit b820e6fb09.
Prior the commit we are reverting, checksum unnecessary was only set when
both the L3 OK and L4 OK bits are set on the CQE. This caused packets
of IP protocols such as SCTP which are not dealt by the current HW L4
parser (hence the L4 OK bit is not set, but the L4 header type none bit
is set) to go through the checksum none code, where currently we wrongly
report checksum unnecessary for them, a regression. Fix this by a revert.
Note that on our usual track we report checksum complete, so the revert
isn't expected to have any notable performance impact. Also, when we are
not on the checksum complete track, the L4 protocols for which we report
checksum none are not high performance ones, we will still report
checksum unnecessary for UDP/TCP.
Fixes: b820e6fb09 ("net/mlx5e: Enable reporting checksum unnecessary also for L3 packets")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Avi Urman <aviu@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
TC encap offload is supported only for the physical uplink
representor. Fail for non uplink representor.
Fixes: 3e621b19b0 ("net/mlx5e: Support TC encapsulation offloads with upper devices")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the two places is_last_ethertype_ip is being called, the caller will
be looking inside the ip header, to be safe, add ip{4,6} header sanity
check. And return true only on valid ip headers, i.e: the whole header
is contained in the linear part of the skb.
Note: Such situation is very rare and hard to reproduce, since mlx5e
allocates a large enough headroom to contain the largest header one can
imagine.
Fixes: fe1dc06999 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an ethernet frame with ip payload is padded, the padding octets are
not covered by the hardware checksum.
Prior to the cited commit, skb checksum was forced to be CHECKSUM_NONE
when padding is detected. After it, the kernel will try to trim the
padding bytes and subtract their checksum from skb->csum.
In this patch we fixup skb->csum for any ip packet with tail padding of
any size, if any padding found.
FCS case is just one special case of this general purpose patch, hence,
it is removed.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
XDP programs might change packets data contents which will make the
reported skb checksum (checksum complete) invalid.
When XDP programs are loaded/unloaded set/clear rx RQs
MLX5E_RQ_STATE_NO_CSUM_COMPLETE flag.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When requested to recover from error, the tx reporter might open new
channels and close the existing ones. Use safe channels switch flow in
order to guarantee opened channels at the end of the recover flow.
For this purpose, define mlx5e_safe_reopen_channels function and use it
within those flows.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Skip recover operation if interface is in down state as TX objects are
not open. This fixes a bug were the recover flow re-opened TX objects
which were not opened before, leading to a possible memory leak at
driver unload.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes: ab412e1dd7 ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rv32_defconfig for 32bit systems. The only
difference between rv32_defconfig and defconfig is that
rv32_defconfig has CONFIG_ARCH_RV32I=y.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the third step to make MT2701 HDMI stable.
We should not change the rate of parent for hdmi phy when
doing round_rate for this clock. The parent clock of hdmi
phy must be the same as it. We change it when doing set_rate
only.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This is the second step to make MT2701 HDMI stable.
The factor depends on the divider of DPI in MT2701, therefore,
we should fix this factor to the right and new one.
Test: search ok
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This is the first step to make MT2701 hdmi stable.
The parent rate of hdmi phy had set by DPI driver.
We should not set or change the parent rate of MT2701 hdmi phy,
as a result we should remove the flags of "CLK_SET_RATE_PARENT"
from the clock of MT2701 hdmi phy.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Recalculate the rate of this clock, by querying hardware to
make implementation of recalc_rate() to match the definition.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Due to a clerical error,there is one zero less for 12800000.
Fix it for 128000000
Fixes: 0fc721b296 ("drm/mediatek: add hdmi driver for MT2701 and MT7623")
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
ACPICA commit b233720031a480abd438f2e9c643080929d144c3
ASL operation_regions declare a range of addresses that it uses. In a
perfect world, the range of addresses should be used exclusively by
the AML interpreter. The OS can use this information to decide which
drivers to load so that the AML interpreter and device drivers use
different regions of memory.
During table load, the address information is added to a global
address range list. Each node in this list contains an address range
as well as a namespace node of the operation_region. This list is
deleted at ACPI shutdown.
Unfortunately, ASL operation_regions can be declared inside of control
methods. Although this is not recommended, modern firmware contains
such code. New module level code changes unintentionally removed the
functionality of adding and removing nodes to the global address
range list.
A few months ago, support for adding addresses has been re-
implemented. However, the removal of the address range list was
missed and resulted in some systems to crash due to the address list
containing bogus namespace nodes from operation_regions declared in
control methods. In order to fix the crash, this change removes
dynamic operation_regions after control method termination.
Link: https://github.com/acpica/acpica/commit/b2337200
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202475
Fixes: 4abb951b73 ("ACPICA: AML interpreter: add region addresses in global list during initialization")
Reported-by: Michael J Gruber <mjg@fedoraproject.org>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Push getting the reference for the encoders' power domains into the
encoder get_power_domains() hook instead of doing this from the caller.
This way the encoder can store away the corresponding wakerefs.
This fixes the DSI encoder disabling, which didn't release these
power references it acquired during HW state readout.
Note that longtime ownership for the corresponding wakerefs can be thus
acquired / released in two ways. Nevertheless there is always only one
owner for them:
After HW readout (booting/system resume):
- encoder->get_power_domains() acquires
- encoder->disable*() releases
After a modeset (calling intel_atomic_commit()):
- encoder->enable*() acquires
- encoder->disable*() releases
* can be any of the encoder enable/disable hooks.
v2:
- Check that the DSI io_wakerefs are unset both during encoder HW
readout and enabling. (Chris)
Fixes: 0e6e0be4c9 ("drm/i915: Markup paired operations on display power domains")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190407124655.31536-1-imre.deak@intel.com
(cherry picked from commit 3a52fb7e79)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull networking fixes from David Miller:
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
Pull TPM fixes from James Morris:
"From Jarkko: These are critical fixes for v5.1. Contains also couple
of new selftests for v5.1 features (partial reads in /dev/tpm0)"
* 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selftests/tpm2: Open tpm dev in unbuffered mode
selftests/tpm2: Extend tests to cover partial reads
KEYS: trusted: fix -Wvarags warning
tpm: Fix the type of the return value in calc_tpm2_event_size()
KEYS: trusted: allow trusted.ko to initialize w/o a TPM
tpm: fix an invalid condition in tpm_common_poll
tpm: turn on TPM on suspend for TPM 1.x
Pull xtensa fixes from Max Filippov:
- fix syscall number passed to trace_sys_exit
- fix syscall number initialization in start_thread
- fix level interpretation in the return_address
- fix format string warning in init_pmd
* tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix format string warning in init_pmd
xtensa: fix return_address
xtensa: fix initialization of pt_regs::syscall in start_thread
xtensa: use actual syscall number in do_syscall_trace_leave
If scsi cmd sglist is not suitable for DDP then csiostor driver uses
preallocated buffers for DDP, because of this data copy is required from
DDP buffer to scsi cmd sglist before calling ->scsi_done().
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Michael Chan says:
====================
bnxt_en: 2 bug fixes.
The first patch prevents possible driver crash if we get a bad RX index
from the hardware. The second patch resets the device when the hardware
reports buffer error to recover from the error.
Please queue these for -stable also. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: fa7e28127a ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Zhivich says:
====================
ethtool: fix use of SPEED_UNKNOWN constant
This patch series addresses 2 related issues:
1. ethtool_validate_speed() triggers a "signed-unsigned comparison"
warning due to type difference of SPEED_UNKNOWN constant (int)
and argument to ethtool_validate_speed (__u32).
2. some drivers use u16 storage for SPEED_UNKNOWN constant,
resulting in value truncation and thus failure to test against
SPEED_UNKNOWN correctly.
This revised series addresses several feedback comments:
- split up the patch in to series
- do not unnecessarily change drivers that use "int" storage
for speed values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building C++ userspace code that includes ethtool.h
with "-Werror -Wall", g++ complains about signed-unsigned comparison in
ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1.
Explicitly cast SPEED_UNKNOWN to __u32 to match type of
ethtool_validate_speed() argument.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi says:
====================
fix possible use-after-free in erspan_v{4,6}
Similar to what I did in commit bb9bd814eb ("ipv6: sit: reset ip
header pointer in ipip6_rcv"), fix possible use-after-free in
erspan_rcv and ip6erspan_rcv extracting tunnel metadata since the
packet can be 'uncloned' running __iptunnel_pull_header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove
erspan header. This can determine a possible use-after-free accessing
pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header
Fixes: 1d7e2ed22f ("net: erspan: refactor existing erspan code")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
erspan tunnels run __iptunnel_pull_header on received skbs to remove
gre and erspan headers. This can determine a possible use-after-free
accessing pkt_md pointer in erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header
Fixes: 1d7e2ed22f ("net: erspan: refactor existing erspan code")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three new tests added:
1. Send get random cmd, read header in 1st read, read the rest in second
read - expect success
2. Send get random cmd, read only part of the response, send another
get random command, read the response - expect success
3. Send get random cmd followed by another get random cmd, without
reading the first response - expect the second cmd to fail with -EBUSY
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Fixes the warning reported by Clang:
security/keys/trusted.c:146:17: warning: passing an object that
undergoes default
argument promotion to 'va_start' has undefined behavior [-Wvarargs]
va_start(argp, h3);
^
security/keys/trusted.c:126:37: note: parameter of type 'unsigned
char' is declared here
unsigned char *h2, unsigned char h3, ...)
^
Specifically, it seems that both the C90 (4.8.1.1) and C11 (7.16.1.4)
standards explicitly call this out as undefined behavior:
The parameter parmN is the identifier of the rightmost parameter in
the variable parameter list in the function definition (the one just
before the ...). If the parameter parmN is declared with ... or with a
type that is not compatible with the type that results after
application of the default argument promotions, the behavior is
undefined.
Link: https://github.com/ClangBuiltLinux/linux/issues/41
Link: https://www.eskimo.com/~scs/cclass/int/sx11c.html
Suggested-by: David Laight <David.Laight@aculab.com>
Suggested-by: Denis Kenzior <denkenz@gmail.com>
Suggested-by: James Bottomley <jejb@linux.vnet.ibm.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.
Fixes: 9488585b21 ("tpm: add support for partial reads")
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.
Fixes: a3fbfae82b ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: a99790bf5c ("r8169: Reinstate ASPM Support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vring_create_virtqueue() allows the caller to specify via the
may_reduce_num parameter whether the vring code is allowed to
allocate a smaller ring than specified.
However, the split ring allocation code tries to allocate a
smaller ring on allocation failure regardless of what the
caller specified. This may cause trouble for e.g. virtio-pci
in legacy mode, which does not support ring resizing. (The
packed ring code does not resize in any case.)
Let's fix this by bailing out immediately in the split ring code
if the requested size cannot be allocated and may_reduce_num has
not been specified.
While at it, fix a typo in the usage instructions.
Fixes: 2a2d1382fe ("virtio: Add improved queue allocation API")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
When moving the documentation for the ieee802154 subsystem from
plain text to rst the file pattern in the MAINTAINERS file got wrong.
Updating it here to fix scripts using this file.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dump_backtrace() with a pt_regs argument corresponding to
userspace doesn't make any sense and our unwinder will simply print
"Call trace:" before unwinding the stack looking for user frames.
Rather than go through this song and dance, just return early if we're
passed a user register state.
Cc: <stable@vger.kernel.org>
Fixes: 1149aad10b ("arm64: Add dump_backtrace() in show_regs")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This options spawns a kernel side thread that will poll for submissions
(and completions, if IORING_SETUP_IOPOLL is set). As this allows a user
to potentially use more cycles outside of the normal hierarchy,
restrict the use of this feature to root.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This ended up not being included in the mainline version of io_uring,
so drop it from the test app as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If there are multiple callbacks queued, waiting for the callback
slot when the callback gets shut down, then they all currently
end up acting as if they hold the slot, and call
nfsd4_cb_sequence_done() resulting in interesting side-effects.
In addition, the 'retry_nowait' path in nfsd4_cb_sequence_done()
causes a loop back to nfsd4_cb_prepare() without first freeing the
slot, which causes a deadlock when nfsd41_cb_get_slot() gets called
a second time.
This patch therefore adds a boolean to track whether or not the
callback did pick up the slot, so that it can do the right thing
in these 2 cases.
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The method of hem free for SCC context is different from qp context.
In the current version, if free SCC hem during the execution of qp free,
there may be smmu error as below:
arm-smmu-v3 arm-smmu-v3.1.auto: event 0x10 received:
arm-smmu-v3 arm-smmu-v3.1.auto: 0x00007d0000000010
arm-smmu-v3 arm-smmu-v3.1.auto: 0x000012000000017c
arm-smmu-v3 arm-smmu-v3.1.auto: 0x00000000000009e0
arm-smmu-v3 arm-smmu-v3.1.auto: 0x0000000000000000
As SCC context is still used by hardware after qp free, we can solve this
problem by removing SCC hem free from hns_roce_qp_free.
Fixes: 6a157f7d1b ("RDMA/hns: Add SCC context allocation support for hip08")
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Overwrite retains the security state after completion of operation. Fix
nfit_test to reflect this so that the kernel can test the behavior it is
more likely to see in practice.
Fixes: 926f74802c ("tools/testing/nvdimm: Add overwrite support for nfit_test")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Due to the incorrect use of the seg and obj information, the position of
the mtt is calculated incorrectly, and the free space of the page is not
enough to store the entire mtt, resulting in access to the next page. This
patch fixes this problem.
Unable to handle kernel paging request at virtual address ffff00006e3cd000
...
Call trace:
hns_roce_write_mtt+0x154/0x2f0 [hns_roce]
hns_roce_buf_write_mtt+0xa8/0xd8 [hns_roce]
hns_roce_create_srq+0x74c/0x808 [hns_roce]
ib_create_srq+0x28/0xc8
Fixes: 0203b14c4f ("RDMA/hns: Unify the calculation for hem index in hip08")
Signed-off-by: chenglang <chenglang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make sure to free the DSR on pvrdma_pci_remove() to avoid the memory leak.
Fixes: 29c8d9eba5 ("IB: Add vmw_pvrdma driver")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The ftrace trampoline code (which deals with modules loaded out of
BL range of the core kernel) uses plt_entries_equal() to check whether
the per-module trampoline equals a zero buffer, to decide whether the
trampoline has already been initialized.
This triggers a BUG() in the opcode manipulation code, since we end
up checking the ADRP offset of a 0x0 opcode, which is not an ADRP
instruction.
So instead, add a helper to check whether a PLT is initialized, and
call that from the frace code.
Cc: <stable@vger.kernel.org> # v5.0
Fixes: bdb85cd1d2 ("arm64/module: switch to ADRP/ADD sequences for PLT entries")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
v2: add hunk that got dropped accidently when this patch was originally
committed. (Alex)
Fixes: 0921c41e19 ("drm/amd/display: Fix negative cursor pos programming")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 6dc4f100c1 ("block: allow bio_for_each_segment_all() to
iterate over multi-page bvec") changes bio_for_each_segment_all()
to use for-inside-for.
This way breaks all bio_for_each_segment_all() call with error out
branch via 'break', since now 'break' can only break from the inner
loop.
Fixes this issue by implementing bio_for_each_segment_all() via
single 'for' loop, and now the logic is very similar with normal
bvec iterator.
Cc: Qu Wenruo <quwenruo.btrfs@gmx.com>
Cc: linux-btrfs@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: Omar Sandoval <osandov@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-and-Tested-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Fixes: 6dc4f100c1 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jason doesn't really have the time to review blk/scsi
patches. Paolo and Setfan agreed to help out.
Thanks guys!
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
broke the radix-mode segment exception handler. In radix mode, this is
exception is not an SLB miss, rather it signals that the EA is outside
the range translated by any page table.
The commit lost the radix feature alternate code patch, which can
cause faults to some EAs to kernel BUG at arch/powerpc/mm/slb.c:639!
The original radix code would send faults to slb_miss_large_addr,
which would end up faulting due to slb_addr_limit being 0. This patch
sends radix directly to do_bad_slb_fault, which is a bit clearer.
Fixes: 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.
Reported-by: syzbot+8f91bd563bbff230d0ee@syzkaller.appspotmail.com
Fixes: 99e3a44bac ("mac80211_hwsim: allow setting iftype support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two problems here:
1. Not all clk_data->hws[] need to be initialized, depending on various
configured quirks. This leads to NULL ptr deref in
clk_hw_unregister_gate() in sun8i_tcon_top_unbind()
2. If there is error when registering the clk_data->hws[],
err_unregister_gates error path will try to unregister
IS_ERR()=true (invalid) pointer.
For problem (1) I have this stack trace:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
clk_hw_unregister+0x8/0x18
clk_hw_unregister_gate+0x14/0x28
sun8i_tcon_top_unbind+0x2c/0x60
component_unbind.isra.4+0x2c/0x50
component_bind_all+0x1d4/0x230
sun4i_drv_bind+0xc4/0x1a0
try_to_bring_up_master+0x164/0x1c0
__component_add+0xa0/0x168
component_add+0x10/0x18
sun8i_dw_hdmi_probe+0x18/0x20
platform_drv_probe+0x3c/0x70
really_probe+0xcc/0x278
driver_probe_device+0x34/0xa8
Problem (2) was identified by head scratching.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405233048.3823-1-megous@megous.com
Setting the module_get_upon_open field for component driver
prevents the module refcount from being incremented during
component probe(). This could lead to the module being
allowed to be unloaded when a pcm stream is open. So,
if this field is set, the module's refcount should be
incremented during pcm open to prevent module removal
when the component is in use. And, the refcount should
be decremented upon pcm close.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently, for Intel platforms the "ignore_module_refcount" field
was introduced for the component driver. In order to avoid a
deadlock preventing the PCI modules from being removed
even when the card was idle, the refcounts were not incremented
for the device driver module during component probe.
However, this change introduced a nasty side effect:
the device driver module can be unloaded while a pcm stream is open.
This patch proposes to change the field to be renamed as
"module_get_upon_open". When this field is set, the module
refcount should be incremented on pcm open amd decremented
upon pcm close. This will enable modules to be removed
when no PCM playback/capture happens and prevent removal
when the component is actually in use.
Also, align with the skylake component driver with the new name.
Fixes: b450b878('ASoC: core: don't increase component module refcount
unconditionally'
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The x86_64 implementation of Poly1305 produces the wrong result on some
inputs because poly1305_4block_avx2() incorrectly assumes that when
partially reducing the accumulator, the bits carried from limb 'd4' to
limb 'h0' fit in a 32-bit integer. This is true for poly1305-generic
which processes only one block at a time. However, it's not true for
the AVX2 implementation, which processes 4 blocks at a time and
therefore can produce intermediate limbs about 4x larger.
Fix it by making the relevant calculations use 64-bit arithmetic rather
than 32-bit. Note that most of the carries already used 64-bit
arithmetic, but the d4 -> h0 carry was different for some reason.
To be safe I also made the same change to the corresponding SSE2 code,
though that only operates on 1 or 2 blocks at a time. I don't think
it's really needed for poly1305_block_sse2(), but it doesn't hurt
because it's already x86_64 code. It *might* be needed for
poly1305_2block_sse2(), but overflows aren't easy to reproduce there.
This bug was originally detected by my patches that improve testmgr to
fuzz algorithms against their generic implementation. But also add a
test vector which reproduces it directly (in the AVX2 case).
Fixes: b1ccc8f4b6 ("crypto: poly1305 - Add a four block AVX2 variant for x86_64")
Fixes: c70f4abef0 ("crypto: poly1305 - Add a SSE2 SIMD variant for x86_64")
Cc: <stable@vger.kernel.org> # v4.3+
Cc: Martin Willi <martin@strongswan.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes the sai driver structure overwriting which results in
a cpu dai name equal NULL.
Fixes: 3e086ed ("ASoC: stm32: add SAI driver")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control values and texts of the enum kcontrol associated
with a widget need to be freed when the widget is removed.
However, both struct snd_soc_dapm_widget and struct soc_enum
contain a dobj member, which resulted in a confusion.
The existing code generates a null pointer dereference by
attempting to free the values and texts from the dobj which
belongs to the widget instead of the dobj belonging to the
enum kcontrol.
The suggested fix is to use the correct dobj member (se->dobj)
of the enum kcontrol.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull crypto fix from Herbert Xu:
"This fixes a bug in the implementation of xcbc and cmac in caam"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix copy of next buffer for xcbc and cmac
When the mtu of a vrf device is set to 0, it would cause ping
failed. So I think we should limit vrf mtu in a reasonable range
to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it
will works for both ipv4 and ipv6. And if dev->max_mtu still be 0
can be confusing, so I set dev->max_mtu to ETH_MAX_MTU.
Here is the reproduce step:
1.Config vrf interface and set mtu to 0:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
2.Ping peer:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.1/16 scope global enp4s0
valid_lft forever preferred_lft forever
connect: Network is unreachable
3.Set mtu to default value, ping works:
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms
Fixes: ad49bc6361 ("net: vrf: remove MTU limits for vrf device")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 510ded33e0 ("slab: implement slab_root_caches list")
changes the name of the list node within "struct kmem_cache" from "list"
to "root_caches_node", but leaks_show() still use the "list" which
causes a crash when reading /proc/slab_allocators.
You need to have CONFIG_SLAB=y and CONFIG_MEMCG=y to see the problem,
because without MEMCG all slab caches are root caches, and the "list"
node happens to be the right one.
Fixes: 510ded33e0 ("slab: implement slab_root_caches list")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tobin C. Harding <tobin@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ppgtt_free_all_spt() iterates the radixtree as it is deleting it,
forgoing all protection against the leaves being freed in the process
(leaving the iter pointing into the void).
A minimal fix seems to be to use the available post_shadow_list to
decompose the tree into a list prior to destroying the radixtree.
Alerted by the sparse warnings:
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
drivers/gpu/drm/i915/gvt/gtt.c:758:45: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:758:45: expected void [noderef] <asn:4> **slot
drivers/gpu/drm/i915/gvt/gtt.c:758:45: got void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void [noderef] <asn:4> **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/gtt.c:757:9: expected void **slot
drivers/gpu/drm/i915/gvt/gtt.c:757:9: got void [noderef] <asn:4> **
This would also have been loudly warning if run through CI for the
invalid RCU dereferences.
Fixes: b6c126a393 ("drm/i915/gvt: Manage shadow pages with radix tree")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fix the sparse warning for blithely using iomem with normal memcpy:
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: expected void *aperture_va
drivers/gpu/drm/i915/gvt/kvmgt.c:916:21: got void [noderef] <asn:2> *
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: warning: incorrect type in argument 1 (different address spaces)
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: expected void [noderef] <asn:2> *vaddr
drivers/gpu/drm/i915/gvt/kvmgt.c:927:26: got void *aperture_va
Fixes: d480b28a41 ("drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This is a follow up of the commit 0db6f8befc ("net/sched: fix ->get
helper of the matchall cls").
To test it:
$ cd tools/testing/selftests/tc-testing
$ ln -s ../plugin-lib/nsPlugin.py plugins/20-nsPlugin.py
$ ./tdc.py -n -e 2638
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b5b4453e79 ("powerpc/vdso64: Fix CLOCK_MONOTONIC
inconsistencies across Y2038") changed the type of wtom_clock_sec
to s64 on PPC64. Therefore, VDSO32 needs to read it with a 4 bytes
shift in order to retrieve the lower part of it.
Fixes: b5b4453e79 ("powerpc/vdso64: Fix CLOCK_MONOTONIC inconsistencies across Y2038")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is similar to commit e285d5bfb7 ("NFC: Fix the number of pipes")
where we changed NFC_HCI_MAX_PIPES from 127 to 128.
As the comment next to the define explains, the pipe identifier is 7
bits long. The highest possible pipe is 127, but the number of possible
pipes is 128. As the code is now, then there is potential for an
out of bounds array access:
net/nfc/nci/hci.c:297 nci_hci_cmd_received() warn: array off by one?
'ndev->hci_dev->pipes[pipe]' '0-127 == 127'
Fixes: 11f54f2286 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to commit 674d9de02a ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands").
I'm not totally sure, but I think that commit description may have
overstated the danger. I was under the impression that this data came
from the firmware? If you can't trust your networking firmware, then
you're already in trouble.
Anyway, these days we add bounds checking where ever we can and we call
it kernel hardening. Better safe than sorry.
Fixes: 11f54f2286 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a number of problems with how arch/x86/include/asm/bitops.h
is currently using assembly constraints for the memory region
bitops are modifying:
1) Use memory clobber in bitops that touch arbitrary memory
Certain bit operations that read/write bits take a base pointer and an
arbitrarily large offset to address the bit relative to that base.
Inline assembly constraints aren't expressive enough to tell the
compiler that the assembly directive is going to touch a specific memory
location of unknown size, therefore we have to use the "memory" clobber
to indicate that the assembly is going to access memory locations other
than those listed in the inputs/outputs.
To indicate that BTR/BTS instructions don't necessarily touch the first
sizeof(long) bytes of the argument, we also move the address to assembly
inputs.
This particular change leads to size increase of 124 kernel functions in
a defconfig build. For some of them the diff is in NOP operations, other
end up re-reading values from memory and may potentially slow down the
execution. But without these clobbers the compiler is free to cache
the contents of the bitmaps and use them as if they weren't changed by
the inline assembly.
2) Use byte-sized arguments for operations touching single bytes.
Passing a long value to ANDB/ORB/XORB instructions makes the compiler
treat sizeof(long) bytes as being clobbered, which isn't the case. This
may theoretically lead to worse code in the case of heavy optimization.
Practical impact:
I've built a defconfig kernel and looked through some of the functions
generated by GCC 7.3.0 with and without this clobber, and didn't spot
any miscompilations.
However there is a (trivial) theoretical case where this code leads to
miscompilation:
https://lkml.org/lkml/2019/3/28/393
using just GCC 8.3.0 with -O2. It isn't hard to imagine someone writes
such a function in the kernel someday.
So the primary motivation is to fix an existing misuse of the asm
directive, which happens to work in certain configurations now, but
isn't guaranteed to work under different circumstances.
[ --mingo: Added -stable tag because defconfig only builds a fraction
of the kernel and the trivial testcase looks normal enough to
be used in existing or in-development code. ]
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: James Y Knight <jyknight@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20190402112813.193378-1-glider@google.com
[ Edited the changelog, tidied up one of the defines. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After this commit
f875a79 nfsd: allow nfsv3 readdir request to be larger.
nfsv3 readdir request size can be larger than PAGE_SIZE. So if the
directory been read is large enough, we can use multiple pages
in rq_respages. Update buffer count and page pointers like we do
in readdirplus to make this happen.
Now listing a directory within 3000 files will panic because we
are counting in a wrong way and would write on random page.
Fixes: f875a79 "nfsd: allow nfsv3 readdir request to be larger"
Signed-off-by: Murphy Zhou <jencce.kernel@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
A recent commit added a call to cache_fresh_locked()
when an expired item was found.
The call sets the CACHE_VALID flag, so it is important
that the item actually is valid.
There are two ways it could be valid:
1/ If ->update has been called to fill in relevant content
2/ if CACHE_NEGATIVE is set, to say that content doesn't exist.
An expired item that is waiting for an update will be neither.
Setting CACHE_VALID will mean that a subsequent call to cache_put()
will be likely to dereference uninitialised pointers.
So we must make sure the item is valid, and we already have code to do
that in try_to_negate_entry(). This takes the hash lock and so cannot
be used directly, so take out the two lines that we need and use them.
Now cache_fresh_locked() is certain to be called only on
a valid item.
Cc: stable@kernel.org # 2.6.35
Fixes: 4ecd55ea07 ("sunrpc: fix cache_head leak due to queued request")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There is a Marvell 88SE9170 PCIe SATA controller I found on a board here.
Some quick testing with the ARM SMMU enabled reveals that it suffers from
the same requester ID mixup problems as the other Marvell chips listed
already.
Add the PCI vendor/device ID to the list of chips which need the
workaround.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
If a child irqchip calls irq_chip_set_wake_parent() but its parent irqchip
has the IRQCHIP_SKIP_SET_WAKE flag set an error is returned.
This is inconsistent behaviour vs. set_irq_wake_real() which returns 0 when
the irqchip has the IRQCHIP_SKIP_SET_WAKE flag set. It doesn't attempt to
walk the chain of parents and set irq wake on any chips that don't have the
flag set either. If the intent is to call the .irq_set_wake() callback of
the parent irqchip, then we expect irqchip implementations to omit the
IRQCHIP_SKIP_SET_WAKE flag and implement an .irq_set_wake() function that
calls irq_chip_set_wake_parent().
The problem has been observed on a Qualcomm sdm845 device where set wake
fails on any GPIO interrupts after applying work in progress wakeup irq
patches to the GPIO driver. The chain of chips looks like this:
QCOM GPIO -> QCOM PDC (SKIP) -> ARM GIC (SKIP)
The GPIO controllers parent is the QCOM PDC irqchip which in turn has ARM
GIC as parent. The QCOM PDC irqchip has the IRQCHIP_SKIP_SET_WAKE flag
set, and so does the grandparent ARM GIC.
The GPIO driver doesn't know if the parent needs to set wake or not, so it
unconditionally calls irq_chip_set_wake_parent() causing this function to
return a failure because the parent irqchip (PDC) doesn't have the
.irq_set_wake() callback set. Returning 0 instead makes everything work and
irqs from the GPIO controller can be configured for wakeup.
Make it consistent by returning 0 (success) from irq_chip_set_wake_parent()
when a parent chip has IRQCHIP_SKIP_SET_WAKE set.
[ tglx: Massaged changelog ]
Fixes: 08b55e2a92 ("genirq: Add irqchip_set_wake_parent")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190325181026.247796-1-swboyd@chromium.org
When ioctl calls are made with non-null-terminated userspace strings,
strlcpy causes an OOB-read from within strlen. Fix by changing to use
strscpy instead.
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Topology is not unloaded in the core during unregister_component()
anymore. So, add the remove() callback that will unload the
topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chips main power supplies VA and VP are enabled during probe but
then never disabled, this will cause warnings from the regulator
framework on driver removal. Fix this by adding a remove callback and
disabling the supplies, whilst doing so follow best practice and put the
chip back into reset as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use %lu instead of %zu to fix the following warning introduced with
recent memblock refactoring:
xtensa/mm/mmu.c:36:9: warning: format '%zu' expects argument of type
'size_t', but argument 3 has type 'long unsigned int
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The PTN5150 dependencies look like they were meant to do the
right thing, but they actually should not allow building without
I2C for compile testing, as that results in a Kconfig warning
and subsequent build failure:
WARNING: unmet direct dependencies detected for REGMAP_I2C
Depends on [m]: I2C [=m]
Selected by [y]:
- EXTCON_PTN5150 [=y] && EXTCON [=y] && (I2C [=m] && GPIOLIB [=y] || COMPILE_TEST [=y])
Selected by [m]:
- EEPROM_AT24 [=m] && I2C [=m] && SYSFS [=y]
- KEYBOARD_CAP11XX [=m] && !UML && INPUT [=y] && INPUT_KEYBOARD [=y] && OF [=y] && I2C [=m]
- INPUT_DRV260X_HAPTICS [=m] && !UML && INPUT_MISC [=y] && INPUT [=y] && I2C [=m] && (GPIOLIB [=y] || COMPILE_TEST [=y])
- ... [many others]
Add parentheses around the expression so we can compile-test
without GPIOLIB but not without I2C.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
memory allocated by kmem_cache_alloc() should be freed using
kmem_cache_free(), not kfree().
Fixes: fa0ca2aee3 ("deal with get_reqs_available() in aio_get_req() itself")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
return_address returns the address that is one level higher in the call
stack than requested in its argument, because level 0 corresponds to its
caller's return address. Use requested level as the number of stack
frames to skip.
This fixes the address reported by might_sleep and friends.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The compression property resets to NULL, instead of the old value if we
fail to set the new compression parameter.
$ btrfs prop get /btrfs compression
compression=lzo
$ btrfs prop set /btrfs compression zli
ERROR: failed to set compression for /btrfs: Invalid argument
$ btrfs prop get /btrfs compression
This is because the compression property ->validate() is successful for
'zli' as the strncmp() used the length passed from the userspace.
Fix it by using the expected string length in strncmp().
Fixes: 63541927c8 ("Btrfs: add support for inode properties")
Fixes: 5c1aab1dd5 ("btrfs: Add zstd support")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We let pass zstd compression parameter even if it is not fully valid.
For example:
$ btrfs prop set /btrfs compression zst
$ btrfs prop get /btrfs compression
compression=zst
zlib and lzo are fine.
Fix it by checking the correct prefix length.
Fixes: 5c1aab1dd5 ("btrfs: Add zstd support")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[Why]
the member sdr_white_level of struct dc_cursor_attributes was not
initialized, then the random value result that
dcn10_set_cursor_sdr_white_level() set error hw_scale value 0x20D9(normal
value is 0x3c00), this cause the black cursor issue.
[how]
just initilize the obj of struct dc_cursor_attributes to zero to avoid
the random value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Tianci Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_bo_restore_shadow would assign zero to r if succeeded.
r would remain zero if there is only one node in shadow_list.
current code would always return failure when r <= 0.
restart the timeout for each wait was a rather problematic bug as well.
The value of tmo SHOULD be changed, otherwise we wait tmo jiffies on each loop.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is because set_fmt ops maybe called when PD is off,
and in such case, regmap_ops will lead system hang.
enale PD before doing regmap_ops.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit da215354eb ("ASoC: simple-card: merge simple-scu-card")
merged simple-scu-audio-card which can handle DPCM into
simple-audio-card.
By this patch, the judgement to select "normal sound card" or
"DPCM sound card" is based on its CPU/Codec DAI count.
But, because of it, existing "simple-audio-card" user who is
assuming "normal sound card" might select DPCM unintentionally.
To solve this issue, this patch allows "simple-audio-card" user
can select "normal sound card", and "simple-scu-audio-card" user
can select both "normal sound card" and "DPCM sound card".
This keeps compatibility collectry.
Fixes: da215354eb ("ASoC: simple-card: merge simple-scu-card")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit ae3cb57909 ("ASoC: audio-graph-card: merge
audio-graph-scu-card") merged audio-graph-scu-card which can
handle DPCM into audio-graph-card.
By this patch, the judgement to select "normal sound card" or
"DPCM sound card" is based on its OF-graph endpoint connection.
But, because of it, existing "audio-graph-card" user who is
assuming "normal sound card" might select DPCM unintentionally.
To solve this issue, this patch allows "audio-graph-card" user
can select "normal sound card", and "audio-graph-scu-card" user
can select both "normal sound card" and "DPCM sound card".
This keeps compatibility collectry.
Fixes: ae3cb57909 ("ASoC: audio-graph-card: merge audio-graph-scu-card")
Reported-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New pt_regs should indicate that there's no syscall, not that there's
syscall #0. While at it wrap macro body in do/while and parenthesize
macro arguments.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Syscall may alter pt_regs structure passed to it, resulting in a
mismatch between syscall entry end syscall exit entries in the ftrace.
Temporary restore syscall field of the pt_regs for the duration of
do_syscall_trace_leave.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The author of these files has changed her name. Update
instances in the code of her dead name to current legal
name.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_CRYPTO is not set or set to m,
gcc building warn this:
lib/iov_iter.o: In function `hash_and_copy_to_iter':
iov_iter.c:(.text+0x9129): undefined reference to `crypto_stats_get'
iov_iter.c:(.text+0x9152): undefined reference to `crypto_stats_ahash_update'
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d05f443554 ("iov_iter: introduce hash_and_copy_to_iter helper")
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
SNVS IRQ is requested before necessary driver data initialized,
if there is a pending IRQ during driver probe phase, kernel
NULL pointer panic will occur in IRQ handler. To avoid such
scenario, just initialize necessary driver data before enabling
IRQ. This patch is inspired by NXP's internal kernel tree.
Fixes: d3dc6e2322 ("input: keyboard: imx: add snvs power key driver")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This accidentally returns the wrong variable. The "req->ki_eventfd"
pointer is NULL so this return success.
Fixes: 7316b49c2a ("aio: move sanity checks and request allocation to io_submit_one()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This adds a SND_PCI_QUIRK(...) line for the Tuxedo XC 1509.
The Tuxedo XC 1509 and the System76 oryp5 are the same barebone
notebooks manufactured by Clevo. To name the fixups both use after the
actual underlying hardware, this patch also changes System76_orpy5
to clevo_pb51ed in 2 enum symbols and one function name,
matching the other pci_quirk entries which are also named after the
device ODM.
Fixes: 7f665b1c32 ("ALSA: hda/realtek - Headset microphone and internal speaker support for System76 oryp5")
Signed-off-by: Richard Sailer <rs@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It will be lose Mic JD state when Chrome OS boot and headset was plugged.
Just Implement of reset combo jack JD verb for ACT_PRE_PROBE state.
Intel test result was also failed.
It test passed until changed the initial state to ACT_INIT.
Mic JD will show every time.
This patch also changed the model name as 'alc-chrome-book' for
application of Chrome OS.
Fixes: 10f5b1b85e ("ALSA: hda/realtek - Fixed Headset Mic JD not stable")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On AMD processors, the detection of an overflowed PMC counter in the NMI
handler relies on the current value of the PMC. So, for example, to check
for overflow on a 48-bit counter, bit 47 is checked to see if it is 1 (not
overflowed) or 0 (overflowed).
When the perf NMI handler executes it does not know in advance which PMC
counters have overflowed. As such, the NMI handler will process all active
PMC counters that have overflowed. NMI latency in newer AMD processors can
result in multiple overflowed PMC counters being processed in one NMI and
then a subsequent NMI, that does not appear to be a back-to-back NMI, not
finding any PMC counters that have overflowed. This may appear to be an
unhandled NMI resulting in either a panic or a series of messages,
depending on how the kernel was configured.
To mitigate this issue, add an AMD handle_irq callback function,
amd_pmu_handle_irq(), that will invoke the common x86_pmu_handle_irq()
function and upon return perform some additional processing that will
indicate if the NMI has been handled or would have been handled had an
earlier NMI not handled the overflowed PMC. Using a per-CPU variable, a
minimum value of the number of active PMCs or 2 will be set whenever a
PMC is active. This is used to indicate the possible number of NMIs that
can still occur. The value of 2 is used for when an NMI does not arrive
at the LAPIC in time to be collapsed into an already pending NMI. Each
time the function is called without having handled an overflowed counter,
the per-CPU value is checked. If the value is non-zero, it is decremented
and the NMI indicates that it handled the NMI. If the value is zero, then
the NMI indicates that it did not handle the NMI.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On AMD processors, the detection of an overflowed counter in the NMI
handler relies on the current value of the counter. So, for example, to
check for overflow on a 48 bit counter, bit 47 is checked to see if it
is 1 (not overflowed) or 0 (overflowed).
There is currently a race condition present when disabling and then
updating the PMC. Increased NMI latency in newer AMD processors makes this
race condition more pronounced. If the counter value has overflowed, it is
possible to update the PMC value before the NMI handler can run. The
updated PMC value is not an overflowed value, so when the perf NMI handler
does run, it will not find an overflowed counter. This may appear as an
unknown NMI resulting in either a panic or a series of messages, depending
on how the kernel is configured.
To eliminate this race condition, the PMC value must be checked after
disabling the counter. Add an AMD function, amd_pmu_disable_all(), that
will wait for the NMI handler to reset any active and overflowed counter
after calling x86_pmu_disable_all().
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new configuration with a new firmware name for quz devices.
And, since these devices have the same PCI device and subsystem IDs,
we need to add some code to switch from a normal qu firmware to the
quz firmware.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With offloaded rate control, if the station parameters (rates, NSS,
bandwidth) change (sta_rc_update method), call iwl_mvm_rs_rate_init()
to propagate those change to the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_tx_mpdu() may run from iwl_mvm_add_new_dqa_stream_wk(), where
soft-IRQs aren't disabled. In this case, it may hold the station lock
and be interrupted by a soft-IRQ that also wants to acquire said lock,
leading to a deadlock.
Fix it by disabling soft-IRQs in iwl_mvm_add_new_dqa_stream_wk().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When an event is programmed with attr.wakeup_events=N (N>0), it means
the caller is interested in getting a user level notification after
N samples have been recorded in the kernel sampling buffer.
With precise events on Intel processors, the kernel uses PEBS.
The kernel tries minimize sampling overhead by verifying
if the event configuration is compatible with multi-entry PEBS mode.
If so, the kernel is notified only when the buffer has reached its threshold.
Other PEBS operates in single-entry mode, the kenrel is notified for each
PEBS sample.
The problem is that the current implementation look at frequency
mode and event sample_type but ignores the wakeup_events field. Thus,
it may not be possible to receive a notification after each precise event.
This patch fixes this problem by disabling multi-entry PEBS if wakeup_events
is non-zero.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Link: https://lkml.kernel.org/r/20190306195048.189514-1-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A NULL pointer dereference bug was reported on a distribution kernel but
the same issue should be present on mainline kernel. It occured on s390
but should not be arch-specific. A partial oops looks like:
Unable to handle kernel pointer dereference in virtual kernel address space
...
Call Trace:
...
try_to_wake_up+0xfc/0x450
vhost_poll_wakeup+0x3a/0x50 [vhost]
__wake_up_common+0xbc/0x178
__wake_up_common_lock+0x9e/0x160
__wake_up_sync_key+0x4e/0x60
sock_def_readable+0x5e/0x98
The bug hits any time between 1 hour to 3 days. The dereference occurs
in update_cfs_rq_h_load when accumulating h_load. The problem is that
cfq_rq->h_load_next is not protected by any locking and can be updated
by parallel calls to task_h_load. Depending on the compiler, code may be
generated that re-reads cfq_rq->h_load_next after the check for NULL and
then oops when reading se->avg.load_avg. The dissassembly showed that it
was possible to reread h_load_next after the check for NULL.
While this does not appear to be an issue for later compilers, it's still
an accident if the correct code is generated. Full locking in this path
would have high overhead so this patch uses READ_ONCE to read h_load_next
only once and check for NULL before dereferencing. It was confirmed that
there were no further oops after 10 days of testing.
As Peter pointed out, it is also necessary to use WRITE_ONCE() to avoid any
potential problems with store tearing.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Fixes: 685207963b ("sched: Move h_load calculation to task_h_load()")
Link: https://lkml.kernel.org/r/20190319123610.nsivgf3mjbjjesxb@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Users have been seeing sound stability issues with max98090 codecs since:
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
At first that commit broke sound for Chromebook Swanky and Clapper models,
the problem was that the machine-driver has been controlling the wrong
clock on those models since support for them was added. This was hidden by
clk-pmc-atom.c keeping the actual clk on unconditionally.
With the machine-driver controlling the proper clock, sound works again
but we are seeing bug reports describing it as: low volume,
"sounds like played at 10x speed" and instable.
When these issues are hit the following message is seen in dmesg:
"max98090 i2c-193C9890:00: PLL unlocked".
Attempts have been made to fix this by inserting a delay between enabling
the clk and enabling and checking the pll, but this has not helped.
It seems that at least on boards which use pmc_plt_clk_0 as clock,
if we ever disable the clk, the pll looses its lock and after that we get
various issues.
This commit fixes this by enabling the clock once at probe time on
these boards. In essence this restores the old behavior of clk-pmc-atom.c
always keeping the clk on on these boards.
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-by: Mogens Jensen <mogens-jensen@protonmail.com>
Reported-by: Dean Wallace <duffydack73@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trigger stop can be called in situations where trigger start failed
and as such it can't be assumed the buffer is already attached to
the compressed stream or a NULL pointer may be dereferenced.
Fixes: 639e5eb3c7 ("ASoC: wm_adsp: Correct handling of compressed streams that restart")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses the device description to clearly identity a device
attached to the bus. It is needed as the currently useed mdevX
notation is not sufficiant in case more than one network
interface controller is being used at the same time.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There be should check return value from dma_set_mask to throw some info
if fail to set dma mask.
Detected by CoverityScan, CID# 1443983: Error handling issues (CHECKED_RETURN)
Fixes: f6f9279f2b ("misc: fastrpc: Add Qualcomm fastrpc basic driver model")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oded writes:
The following bug fix is included in this tag:
- Fix the low credit limit for DMA channel #0. Without this fix, the
channel is unusable by the user.
* tag 'misc-habanalabs-fixes-2019-04-01' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: remove low credit limit of DMA #0
The uapi header asound.h defines types based on struct timespec. We need
to #include <time.h> to get access to the definition of this struct.
Previously, we encountered the following error message when building
applications with a clang/bionic toolchain:
kernel-headers/sound/asound.h:350:19: error: field has incomplete type 'struct timespec'
struct timespec trigger_tstamp;
^
The absence of the time.h #include statement does not cause build errors
with glibc, because its version of stdlib.h indirectly includes time.h.
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer TravelMate B114-21 laptop cannot detect and record sound from
headset MIC. This patch adds the ALC233_FIXUP_ACER_HEADSET_MIC HDA verb
quirk chained with ALC233_FIXUP_ASUS_MIC_NO_PRESENCE pin quirk to fix
this issue.
[ fixed the missing brace and reordered the entry -- tiwai ]
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jonathan writes:
First set of IIO fixes for the 5.1 cycle.
Mostly the usual mix, but the bme680 SPI fix is much larger than
I would normally like. It never worked, but conversely we have
code there that would make people expect it to do so. Chances
of side effects are very low.
* core
- Fix an uninitialised bitaks that could potentially result in random
channels being enabled on startup.
* ad7192
- Fix a wrong channel address for ad7193.
* ade7854
- Fix a typo that results in returning peak voltage instead of peak current.
* at91
- Fix a potential hang due to a race on interrupt setting.
* bmg160
- Fix scale factor of temperature
* bme680
- Fix scale factor of temperature
- Fix SPI read interface. This is a bit of a large patch as it seems
that it never worked. It's major for this driver but is unlikely to
have any negative side effects.
* kxcjk1013
- restore sensor range setting after resume.
* mcp4725
- make sure to store powerdown bits when storing to the eeprom.
* mpu3050
- Mask the chip ID correctly as we have chips that set the bother bits of
this register.
* sgp30
- Fix a missing Kconfig block that means the driver doesn't actually ever
get built.
* tag 'iio-fixes-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
iio: Fix scan mask selection
staging: iio: ad7192: Fix ad7193 channel address
iio/gyro/bmg160: Use millidegrees for temperature scale
Staging: iio: meter: fixed typo
Currently, buffers, schedulers, src's, encoders, decoders
and effect type dapm widgets remain always on as their
power_check method is not set. Setting this callback allows these
widgets in the audio path to be powered managed properly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If for any reason, the backend does not have the requested substream
(like capture on a playback only backend), the BE will be skipped in
dpcm_be_dai_startup().
However, dpcm_apply_symmetry() does not skip those BE and will
dereference the be_substream (NULL) pointer anyway.
Like in dpcm_be_dai_startup(), just skip those BE.
Fixes: 906c7d690c ("ASoC: dpcm: Apply symmetry for DPCM")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't want to overwrite "ret", it already holds the correct error
code. The "regmap" variable might be a valid pointer as this point.
Fixes: 8f83f26891 ("drm/mediatek: Add HDMI support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Commit 0df977eafc ("powerpc/6xx: Don't use SPRN_SPRG2 for storing
stack pointer while in RTAS") changes the code to use a field in
thread struct to store the stack pointer while in RTAS instead of
using SPRN_SPRG2. It therefore converts all places which were
manipulating SPRN_SPRG2 to use that field. During early startup, the
zeroing of SPRN_SPRG2 has been replaced by a zeroing of that field in
thread struct. But at least in start_here, that's done wrongly because
it used the physical address of the fields while MMU is on at that
time.
So the virtual address of the field should be used instead, but in
the meantime, thread struct has already been zeroed and initialised
so we can just drop this initialisation.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Fixes: 0df977eafc ("powerpc/6xx: Don't use SPRN_SPRG2 for storing stack pointer while in RTAS")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The common pins were mistakenly not added to the DAPM graph.
Adding these pins will allow valid graphs to be created.
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->info_exist_lock){+.+.}:
__mutex_lock+0x70/0xa3c
mutex_lock_nested+0x1c/0x24
iio_read_channel_raw+0x1c/0x60
iio_read_channel_info+0xa8/0xb0
dev_attr_show+0x1c/0x48
sysfs_kf_seq_show+0x84/0xec
seq_read+0x154/0x528
__vfs_read+0x2c/0x15c
vfs_read+0x8c/0x110
ksys_read+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbedefb60
-> #0 (kn->count#30){++++}:
lock_acquire+0xd8/0x268
__kernfs_remove+0x288/0x374
kernfs_remove_by_name_ns+0x3c/0x84
remove_files+0x34/0x78
sysfs_remove_group+0x40/0x9c
sysfs_remove_groups+0x24/0x34
device_remove_attrs+0x38/0x64
device_del+0x11c/0x360
cdev_device_del+0x14/0x2c
iio_device_unregister+0x24/0x60
release_nodes+0x1bc/0x200
device_release_driver_internal+0x1a0/0x230
unbind_store+0x80/0x130
kernfs_fop_write+0x100/0x1e4
__vfs_write+0x2c/0x160
vfs_write+0xa4/0x17c
ksys_write+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbe906840
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->info_exist_lock);
lock(kn->count#30);
lock(&dev->info_exist_lock);
lock(kn->count#30);
*** DEADLOCK ***
...
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With zero-key defined, we can remove previous detection of key id 0 or null
key in order to deal with a zero-key situation. Syncing all security
commands to use the zero-key. Helper functions are introduced to return the
data that points to the actual key payload or the zero_key. This helps
uniformly handle the key material even with zero_key.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a zero key in order to standardize hardware that want a key of 0's to
be passed. Some platforms defaults to a zero-key with security enabled
rather than allow the OS to enable the security. The zero key would allow
us to manage those platform as well. This also adds a fix to secure erase
so it can use the zero key to do crypto erase. Some other security commands
already use zero keys. This introduces a standard zero-key to allow
unification of semantics cross nvdimm security commands.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
First batch of iwlwifi fixes intended for v5.1
* add some new PCI IDs (plus a struct name change they depend on);
* fix crypto with new devices, namely 22560 and above;
* a bunch of fixes (and a dependency) for the new debugging infra;
Pull more fixes for meson clocks from Neil Armstrong:
- clk-pll: fix rate rounding fixing meson8b boot failure
- vid-pll-div: fix recal_rate warning and return when invalid setting
* tag 'meson-clk-fixes-for-5.1-v2' of https://github.com/BayLibre/clk-meson:
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
Holding the lock around the entire duration of tx scheduling can create
some nasty lock contention, especially when processing airtime information
from the tx status or the rx path.
Improve locking by only holding the active_txq_lock for lookups / scheduling
list modifications.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds NL80211_FLAG_CLEAR_SKB flag to other NL commands
that carry key data to ensure they do not stick around on heap
after the SKB is freed.
Also introduced this flag for NL80211_CMD_VENDOR as there are sub
commands which configure the keys.
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are several scenarios in which mac80211 can call drv_wake_tx_queue
after ieee80211_restart_hw has been called and has not yet completed.
Driver private structs are considered uninitialized until mac80211 has
uploaded the vifs, stations and keys again, so using private tx queue
data during that time is not safe.
The driver can also not rely on drv_reconfig_complete to figure out when
it is safe to accept drv_wake_tx_queue calls again, because it is only
called after all tx queues are woken again.
To fix this, bail out early in drv_wake_tx_queue if local->in_reconfig
is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building with -Wsometimes-uninitialized, Clang warns:
net/wireless/util.c:1223:11: warning: variable 'result' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Clang can't evaluate at this point that WARN(1, ...) always returns true
because __ret_warn_on is defined as !!(condition), which isn't
immediately evaluated as 1. Change this branch to else so that it's
clear to Clang that we intend to bail out here.
Link: https://github.com/ClangBuiltLinux/linux/issues/382
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
skb->truesize can change due to memory reallocation or when adding extra
fragments. Adjust fq->memory_usage accordingly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The support added for regulatory WMM rules did not handle
the case of regulatory domain intersections. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Looks that 100 chars isn't enough for messages, as we keep getting
warnings popping from different places due to message shortening.
Instead of trying to shorten the prints, just increase the buffer size.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer to the last four bytes of the address is not guaranteed to be
aligned, so we need to use __get_unaligned_cpu32 here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Once a station enters powersave, its queues should not be returned by
ieee80211_next_txq() anymore. They will be re-scheduled again after the
station has woken up again
Fixes: 1866760096 ("mac80211: Add TXQ scheduling API")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vid_pll_div is a programmable fractional divider, but vendor gives a
limited of known configuration value and it's corresponding fraction.
Thus when at reset value (0) or unknown value, we cannot determine the
result rate.
The initial behaviour was to print a warning, but the warning triggers
at each boot and when the clock tree is refreshed.
This patch moves the print to debug and returns 0 instead of the
parent rate.
Fixes: 72dbb8c94d ("clk: meson: Add vid_pll divider driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lkml.kernel.org/r/20190327151348.27402-1-narmstrong@baylibre.com
The DASD driver incorrectly limits the maximum number of blocks of ECKD
DASD volumes to 32 bit numbers. Volumes with a capacity greater than
2^32-1 blocks are incorrectly recognized as smaller volumes.
This results in the following volume capacity limits depending on the
formatted block size:
BLKSIZE MAX_GB MAX_CYL
512 2047 5843492
1024 4095 8676701
2048 8191 13634816
4096 16383 23860929
The same problem occurs when a volume with more than 17895697 cylinders
is accessed in raw-track-access mode.
Fix this problem by adding an explicit type cast when calculating the
maximum number of blocks.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IS_ENABLED should generally use CONFIG_ prefaced symbols and
it doesn't appear as if there is a BLK_DEV_INITRD define.
Cc: <stable@vger.kernel.org> # 4.20
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Whan a filesystem is mounted with the nologreplay mount option, which
requires it to be mounted in RO mode as well, we can not allow discard on
free space inside block groups, because log trees refer to extents that
are not pinned in a block group's free space cache (pinning the extents is
precisely the first phase of replaying a log tree).
So do not allow the fitrim ioctl to do anything when the filesystem is
mounted with the nologreplay option, because later it can be mounted RW
without that option, which causes log replay to happen and result in
either a failure to replay the log trees (leading to a mount failure), a
crash or some silent corruption.
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Fixes: 96da09192c ("btrfs: Introduce new mount option to disable tree log replay")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The alcor driver is setting up data transfer and submitting the associated
MMC command at the same time. While this works most of the time, it
occasionally causes problems upon write.
In the working case, after setting up the data transfer and submitting
the MMC command, an interrupt comes in a moment later with CMD_END and
WRITE_BUF_RDY bits set. The data transfer then happens without problem.
However, on occasion, the interrupt that arrives at that point only
has WRITE_BUF_RDY set. The hardware notifies that it's ready to write
data, but the associated MMC command is still running. Regardless, the
driver was proceeding to write data immediately, and that would then cause
another interrupt indicating data CRC error, and the write would fail.
Additionally, the transfer setup function alcor_trigger_data_transfer()
was being called 3 times for each write operation, which was confusing
and may be contributing to this issue.
Solve this by tweaking the driver behaviour to follow the sequence observed
in the original ampe_stor vendor driver:
1. When starting request handling, write 0 to DATA_XFER_CTRL
2. Submit the command
3. Wait for CMD_END interrupt and then trigger data transfer
4. For the PIO case, trigger the next step of the data transfer only
upon the following DATA_END interrupt, which occurs after the block has
been written.
I confirmed that the read path still works (DMA & PIO) and also now
presents more consistency with the operations performed by ampe_stor.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: c5413ad815 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix a side effect of adding xcbc support, when the next_buffer is not
copied.
The issue occurs, when there is stored from previous state a blocksize
buffer and received, a less than blocksize, from user. In this case, the
nents for req->src is 0, and the next_buffer is not copied.
An example is:
{
.tap = { 17, 15, 8 },
.psize = 40,
.np = 3,
.ksize = 16,
}
Fixes: 12b8567f6f ("crypto: caam - add support for xcbc(aes)")
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If page-fault handler spans multiple MRs then the access mask needs to
be reset before each MR handling or otherwise write access will be
granted to mapped pages instead of read-only.
Cc: <stable@vger.kernel.org> # 3.19
Fixes: 7bdf65d411 ("IB/mlx5: Handle page faults")
Reported-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The receive side mapping (RSM) on hfi1 hardware is a special
matching mechanism to direct an incoming packet to a given
hardware receive context. It has 4 instances of matching capabilities
(RSM0 - RSM3) that share the same RSM table (RMT). The RMT has a total of
256 entries, each of which points to a receive context.
Currently, three instances of RSM have been used:
1. RSM0 by QOS;
2. RSM1 by PSM FECN;
3. RSM2 by VNIC.
Each RSM instance should reserve enough entries in RMT to function
properly. Since both PSM and VNIC could allocate any receive context
between dd->first_dyn_alloc_ctxt and dd->num_rcv_contexts, PSM FECN must
reserve enough RMT entries to cover the entire receive context index
range (dd->num_rcv_contexts - dd->first_dyn_alloc_ctxt) instead of only
the user receive contexts allocated for PSM
(dd->num_user_contexts). Consequently, the sizing of
dd->num_user_contexts in set_up_context_variables is incorrect.
Fixes: 2280740f01 ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When an old ack_queue entry is used to store an incoming request, it may
need to clean up the old entry if it is still referencing the
MR. Originally only RDMA READ request needed to reference MR on the
responder side and therefore the opcode was tested when cleaning up the
old entry. The introduction of tid rdma specific operations in the
ack_queue makes the specific opcode tests wrong. Multiple opcodes (RDMA
READ, TID RDMA READ, and TID RDMA WRITE) may need MR ref cleanup.
Remove the opcode specific tests associated with the ack_queue.
Fixes: f48ad614c1 ("IB/hfi1: Move driver out of staging")
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When a QP is put into error state, it may be waiting for send engine
resources. In this case, the QP will be removed from the send engine's
waiting list, but its IOWAIT pending bits are not cleared. This will
normally not have any major impact as the QP is being destroyed. However,
the QP still needs to wind down its operations, such as draining the send
queue by scheduling the send engine. Clearing the pending bits will avoid
any potential complications. In addition, if the QP will eventually hang,
clearing the pending bits can help debugging by presenting a consistent
picture if the user dumps the qp_stats.
This patch clears a QP's IOWAIT_PENDING_IB and IO_PENDING_TID bits in
priv->s_iowait.flags in this case.
Fixes: 5da0fc9dbf ("IB/hfi1: Prepare resource waits for dual leg")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When a QP is put into error state, all pending requests in the send work
queue should be drained. The following sequence of events could lead to a
failure, causing a request to hang:
(1) The QP builds a packet and tries to send through SDMA engine.
However, PIO engine is still busy. Consequently, this packet is put on
the QP's tx list and the QP is put on the PIO waiting list. The field
qp->s_flags is set with HFI1_S_WAIT_PIO_DRAIN;
(2) The QP is put into error state by the user application and
notify_error_qp() is called, which removes the QP from the PIO waiting
list and the packet from the QP's tx list. In addition, qp->s_flags is
cleared of RVT_S_ANY_WAIT_IO bits, which does not include
HFI1_S_WAIT_PIO_DRAIN bit;
(3) The hfi1_schdule_send() function is called to drain the QP's send
queue. Subsequently, hfi1_do_send() is called. Since the flag bit
HFI1_S_WAIT_PIO_DRAIN is set in qp->s_flags, hfi1_send_ok() fails. As
a result, hfi1_do_send() bails out without draining any request from
the send queue;
(4) The PIO engine completes the sending and tries to wake up any QP on
its waiting list. But the QP has been removed from the PIO waiting
list and therefore is kept in sleep forever.
The fix is to clear qp->s_flags of HFI1_S_ANY_WAIT_IO bits in step (2).
HFI1_S_ANY_WAIT_IO includes RVT_S_ANY_WAIT_IO and HFI1_S_WAIT_PIO_DRAIN.
Fixes: 2e2ba09e48 ("IB/rdmavt, IB/hfi1: Create device dependent s_flags")
Cc: <stable@vger.kernel.org> # 4.19.x+
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In case kmemdup fails, the fix releases resources and returns to
avoid the NULL pointer dereference.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
According to HUT 1.12 usage 0xb5 from the generic desktop page is reserved
for switching between external and internal display, so let's add the
mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUT 1.12 usage 0x232 from the consumer page is reserved for
switching application between full screen and windowed mode, so let's add
the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR73 usages 0x79, 0x7a and 0x7c from the consumer page
correspond to Brightness Up/Down/Toggle keys, so let's add the mappings.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR77 usage 0x29f from the consumer page is reserved for
the Desktop application to present all running user’s application windows.
Linux defines KEY_SCALE to request Compiz Scale (Expose) mode, so let's
add the mapping.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to HUTRR37 usage 0x6d from the consumer usage page corresponds
to action that selects the next available supported aspect ratio option
on a device which outputs or displays video. However KEY_ZOOM means
activate "Full Screen" mode, KEY_ASPECT_RATIO should be used instead.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We defined better names for keys to activate full screen mode or
change aspect ratio (while keeping the existing keycodes to avoid
breaking userspace), so let's use them in the document.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is hard to say what KEY_SCREEN and KEY_ZOOM mean, but historically DVB
folks have used them to indicate switch to full screen mode. Later, they
converged on using KEY_ZOOM to switch into full screen mode and KEY)SCREEN
to control aspect ratio (see Documentation/media/uapi/rc/rc-tables.rst).
Let's commit to these uses, and define:
- KEY_FULL_SCREEN (and make KEY_ZOOM its alias)
- KEY_ASPECT_RATIO (and make KEY_SCREEN its alias)
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are many Lenovo laptops which need elan_i2c support, this patch adds
relevant IDs to the Elan driver so that touchpads are recognized.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To enable S24_LE format, sample_type in topology fw has to be set to 1.
But sample_type defined in topology firmware configuration is not
getting reflected in the dsp param. This patch sets sample_type in base
config so that the sample type defined in the topology firmware is reflected
in the dsp params. This issues was uncovered while debugging the S24_LE format
which require the MSB byte in 32 bit word to be skipped. Setting sample_type
in topology firmware to 1 helps to skip MSB byte word.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make meson_clk_pll_is_better() consider a rate that precisely matches
the requested rate to be better than any previous rate (which was
smaller than the current).
Prior to commit 8eed1db1ad ("clk: meson: pll: update driver for the
g12a") meson_clk_get_pll_settings() returned early (before calling
meson_clk_pll_is_better()) if the rate from the current iteration
matches the requested rate precisely. After this commit
meson_clk_pll_is_better() is called unconditionally. This requires
meson_clk_pll_is_better() to work with the case where "now == rate".
This fixes a hang during boot on Meson8b / Odroid-C1 for me.
Fixes: 8eed1db1ad ("clk: meson: pll: update driver for the g12a")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190324164327.22590-2-martin.blumenstingl@googlemail.com
This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates,
while only supporting low TMDS bit rates
This to avoid communicating with the SCDC DDC slave uncessary, and
setting the DW-HDMI TMDS Scrambler setup when not supported by the
underlying hardware.
Reported-by: Rob Herring <robh@kernel.org>
Fixes: 264fce6cc2 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315095414.28520-1-narmstrong@baylibre.com
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because DMA #0 is now used by the user, remove the limitation of credits
from this channel. Without this patch, this channel is pretty much
unusable due to its very low bandwidth configuration.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In case kmemdup fails, the fix goes to blk_err to avoid NULL
pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dynamic-debug statements for command payload output only get emitted
when the command is not ND_CMD_CALL. Move the output payload dumping
ahead of the early return path for ND_CMD_CALL.
Fixes: 31eca76ba2 ("...whitelisted dimm command marshaling mechanism")
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In case of alive interrupt timeout or any failure in the init flow
the driver generates FW nmi. The driver assumes that the nmi will
generate SW interrupt. This assumption does not hold and leads to faulty
behavior in the recovery flow.
Solve this by using sync nmi, this way, even if the driver does not
receive SW interrupt, it still starts the recovery flow.
Also remove the wait queue from iwl_fwrt_stop_device since the driver is
handling the SW interrupt synchronously.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver initiates the size value with the size of the struct and then
adds the size of the data and checks if the size is zero so size can not
be equal to zero.
Solve this by getting the data size, check that it is not equal to zero
and only then add the struct size.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the driver fails to dump a memory region, and this is the last
region, then partial region would be extracted.
Solve this by setting the data to zero in case of failure.
This will cause dump to be a list of consecutive successful memory
regions and trailing zeros with no partial memories extracted.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the old days, we could transmit with HW crypto with an arbitrary
key by filling it into TX_CMD. This was broken first with the advent
of CCMP/GCMP-256 keys which don't fit there.
This was broken *again* with the newer TX_CMD format on 22560+,
where we simply cannot pass key material anymore. However, we forgot
to update all the cases when we get a key from mac80211 and don't
program it into the hardware but still return 0 for HW crypto on TX.
In AP mode with WEP, we tried to fix this by programming the keys
separately for each station later, but this ultimately turns out to
be buggy, for example now it leaks memory when we have more than one
WEP key.
Fix this by simply using only SW crypto for WEP in newer devices by
returning -EOPNOTSUPP instead of trying to program WEP keys later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is very low possibility ( < 0.1% ) that channel swap happened
in beginning when multi output/input pin is enabled. The issue is
that hardware can't send data to correct pin in the beginning with
the normal enable flow.
This is hardware issue, but there is no errata, the workaround flow
is that: Each time playback/recording, firstly clear the xSMA/xSMB,
then enable TE/RE, then enable xSMB and xSMA (xSMB must be enabled
before xSMA). Which is to use the xSMA as the trigger start register,
previously the xCR_TE or xCR_RE is the bit for starting.
Fixes commit 43d24e76b6 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a constraint for the channel number setting on the
asrc of older version (e.g. imx35), the channel number should
be even, odd number isn't valid.
So add this constraint when the asrc of older version is used.
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS4270 does not by default increment the register address on
consecutive writes. During normal operation it doesn't matter as all
register accesses are done individually. At resume time after suspend,
however, the regcache code gathers the biggest possible block of
registers to sync and sends them one on one go.
To fix this, set the INCR bit in all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register platform component with a prefix, to avoid warnings
on debugfs entries creation, due to component name
redundancy.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DFSDM must be stopped when a new setting is applied.
restart systematically DFSDM on multiple prepare calls,
to apply changes.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull a round of fixes for meson clocks from Neil Armstrong:
- g12a: Fix VPU clock parents and mux mask
- gxbb: Add CLK_DIVIDER_ROUND_CLOSEST to video decoder clocks
* tag 'meson-clk-fixes-for-5.1' of https://github.com/BayLibre/clk-meson:
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
When dev_exception_add() returns an error (due to a failed memory
allocation), make sure that we move the RCU preemption count back to where
it was before we were called. We dropped the RCU read lock inside the loop
body, so we can't just "break".
sparse complains about this, too:
$ make -s C=2 security/device_cgroup.o
./include/linux/rcupdate.h:647:9: warning: context imbalance in
'propagate_exception' - unexpected unlock
Fixes: d591fb5661 ("device_cgroup: simplify cgroup tree walk in propagate_exception()")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If a watchdog timeout is received from the DSP it is safe to assume the
DSP is not functioning anymore and as such any active compressed streams
should be put into an error state.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Best to lock across handling the bus error to ensure the DSP doesn't
change power state as we are reading the status registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During recent logging improvements it seems two error messages lost
their updates during patch application/rebasing. Add these back in.
Fixes: 0d3fba3e7a ("ASoC: wm_adsp: Improve logging messages")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously support was added to allow streams to be stopped and
started again without the DSP being power cycled and this was done
by clearing the buffer state in trigger start. Another supported
use-case is using the DSP for a trigger event then opening the
compressed stream later to receive the audio, unfortunately clearing
the buffer state in trigger start destroys the data received
from such a trigger. Correct this issue by moving the call to
wm_adsp_buffer_clear to be in trigger stop instead.
Fixes: 61fc060c40 ("ASoC: wm_adsp: Support streams which can start/stop with DSP active")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some application which need kernel virtual address, such as fbcon,
implement these function to map/unmap kernel virtual address of prime
buffer.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Since commit ad67b74d24 ("printk: hash addresses printed with %p"),
at boot "____ptrval____" is printed instead of actual addresses:
percpu: Embedded 38 pages/cpu @(____ptrval____) s124376 r0 d31272 u524288
Instead of changing the print to "%px", and leaking kernel addresses,
just remove the print completely, cfr. e.g. commit 071929dbdd
("arm64: Stop printing the virtual memory layout").
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
If ASRC turns on, HW will use clk_dac as the reference clock
whether recording or playback.
Both of clk_dac and clk_adc should set proper clock while using ASRC.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jack type detection needs the main bias power of analog.
The modification makes sure the main bias power on/off while jack plug/unplug.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ function may not work when system suspend.
We remove snd_soc_dapm_force_enable_pin function call to
make sure the bias off when idle and run into suspend/resume function.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skip for i2s5 in mck_disable which is also bypassed in mck_enable.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without IIO_TRIGGERED_BUFFER, this driver fails to link:
drivers/iio/chemical/pms7003.o: In function `pms7003_probe':
pms7003.c:(.text+0x21c): undefined reference to `devm_iio_triggered_buffer_setup'
pms7003.c:(.text+0x21c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_iio_triggered_buffer_setup'
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Calculation did not use IIO_DEGREE_TO_RAD and implemented a variant to
avoid precision loss as we aim a nano value. The offset added to avoid
rounding error, though, doesn't give us a close result to the expected
value. E.g.
For 1000dps, the result should be:
(1000 * pi ) / 180 >> 15 ~= 0.000532632218
But with current calculation we get
$ cat scale
0.000547890
Fix the calculation by just doing the maths involved for a nano value
val * pi * 10e12 / (180 * 2^15)
so we get a closer result.
$ cat scale
0.000532632
Fixes: c14dca07a3 ("iio: cros_ec_sensors: add ChromeOS EC Contiguous Sensors driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In remove, the clock is disabled before canceling the
delayed work. This means that the delayed work may be
touching unclocked hardware.
Fix by disabling the clock after the delayed work is
fully canceled. This is consistent with the probe error
path order.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If probe errors out after request_irq(), its error path
does not explicitly cancel the delayed work, which may
have been scheduled by the interrupt handler.
This means the delayed work may still be running when
the core frees the private structure (struct xadc).
This is a potential use-after-free.
Fix by inserting cancel_delayed_work_sync() in the probe
error path.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When cancel_delayed_work() returns, the delayed work may still
be running. This means that the core could potentially free
the private structure (struct xadc) while the delayed work
is still using it. This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync(), which waits for
any residual work to finish before returning.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.
This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Architectures like ppc64 use the deposited page table to store hardware
page table slot information. Make sure we deposit a page table when
using zero page at the pmd level for hash.
Without this we hit
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000082a74
Oops: Kernel access of bad area, sig: 11 [#1]
....
NIP [c000000000082a74] __hash_page_thp+0x224/0x5b0
LR [c0000000000829a4] __hash_page_thp+0x154/0x5b0
Call Trace:
hash_page_mm+0x43c/0x740
do_hash_page+0x2c/0x3c
copy_from_iter_flushcache+0xa4/0x4a0
pmem_copy_from_iter+0x2c/0x50 [nd_pmem]
dax_copy_from_iter+0x40/0x70
dax_iomap_actor+0x134/0x360
iomap_apply+0xfc/0x1b0
dax_iomap_rw+0xac/0x130
ext4_file_write_iter+0x254/0x460 [ext4]
__vfs_write+0x120/0x1e0
vfs_write+0xd8/0x220
SyS_write+0x6c/0x110
system_call+0x3c/0x130
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
After commit fbeec965b8 ("ASoC: samsung: odroid: Fix 32000 sample rate
handling") the audio root clock frequency is configured improperly for
44100 sample rate. Due to clock rate rounding it's 20070401 Hz instead
of 22579000 Hz. This results in a too low value of the PSR clock divider
in the CPU DAI driver and too fast actual sample rate for fs=44100. E.g.
1 kHz tone has actual 1780 Hz frequency (1 kHz * 20070401/22579000 * 2).
Fix this by increasing the correction passed to clk_set_rate() to take
into account inaccuracy of the EPLL frequency properly.
Fixes: fbeec965b8 ("ASoC: samsung: odroid: Fix 32000 sample rate handling")
Reported-by: JaeChul Lee <jcsing.lee@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver changes the stream name of DAC and ADC to avoid the issue of
widget with prefixed name. When the machine adds prefixed name for codec,
the stream name of DAI may not find the widgets.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
compiler complains about following declarations
sound/soc/sh/rcar/src.c:174:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 bsdsr_table_pattern1[] = {
^~~~~
sound/soc/sh/rcar/src.c:183:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 bsdsr_table_pattern2[] = {
^~~~~
sound/soc/sh/rcar/src.c:192:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 bsisr_table[] = {
^~~~~
sound/soc/sh/rcar/src.c:201:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 chan288888[] = {
^~~~~
sound/soc/sh/rcar/src.c:210:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 chan244888[] = {
^~~~~
sound/soc/sh/rcar/src.c:219:1: warning: 'static' is not at beginning of declaration [-Wold-style-declaration]
const static u32 chan222222[] = {
^~~~~
This patch moves the 'static' keyword to the front of the
declaration to fix the compiler warnings
Fixes: linux-next commit 7674bec4fc ("ASoC: rsnd: update BSDSR/BSDISR handling")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
lockdep warns us that priv->lock and k->k_lock can cause a
deadlock when after acquire of k->k_lock, process is interrupted
by src, while in another routine of src .init, k->k_lock is
acquired with priv->lock held.
This patch avoids a potential deadlock by not calling soc_device_match()
in SRC .init callback, instead it adds new soc fields in priv->flags to
differentiate SoCs.
Fixes: linux-next commit 7674bec4fc ("ASoC: rsnd: update BSDSR/BSDISR handling")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Declare SR as volatile, as it is changed by hardware.
- Remove TXDR from readable and volatile register list,
as it is intended for write accesses only.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has two issues when machine add prefix name for codec.
(1)The stream name of DAI can't find the AIF widgets.
(2)The drivr can enable/disalbe the MICBIAS and SAR widgets.
The patch will fix these issues caused by prefixed name added.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dpcm get from fe_clients/be_clients
may be free before use
Add a spin lock at snd_soc_card level,
to protect the dpcm instance.
The lock may be used in atomic context, so use spin lock.
Use irq spin lock version,
since the lock may be used in interrupts.
possible race condition between
void dpcm_be_disconnect(
...
list_del(&dpcm->list_be);
list_del(&dpcm->list_fe);
kfree(dpcm);
...
and
for_each_dpcm_fe()
for_each_dpcm_be*()
race condition example
Thread 1:
snd_soc_dapm_mixer_update_power()
-> soc_dpcm_runtime_update()
-> dpcm_be_disconnect()
-> kfree(dpcm);
Thread 2:
dpcm_fe_dai_trigger()
-> dpcm_be_dai_trigger()
-> snd_soc_dpcm_can_be_free_stop()
-> if (dpcm->fe == fe)
Excpetion Scenario:
two FE link to same BE
FE1 -> BE
FE2 ->
Thread 1: switch of mixer between FE2 -> BE
Thread 2: pcm_stop FE1
Exception:
Unable to handle kernel paging request at virtual address dead0000000000e0
pc=<> [<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
sound/soc/soc-pcm.c:3226
if (dpcm->fe == fe)
lr=<> [<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
Backtrace:
[<ffffff89602dba80>] notify_die+0x68/0xb8
[<ffffff896028c7dc>] die+0x118/0x2a8
[<ffffff89602a2f84>] __do_kernel_fault+0x13c/0x14c
[<ffffff89602a27f4>] do_translation_fault+0x64/0xa0
[<ffffff8960280cf8>] do_mem_abort+0x4c/0xd0
[<ffffff8960282ad0>] el1_da+0x24/0x40
[<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
[<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
[<ffffff8960e2edec>] dpcm_fe_dai_trigger+0x3c/0x44
[<ffffff8960de5588>] snd_pcm_do_stop+0x50/0x5c
[<ffffff8960dded24>] snd_pcm_action+0xb4/0x13c
[<ffffff8960ddfdb4>] snd_pcm_drop+0xa0/0x128
[<ffffff8960de69bc>] snd_pcm_common_ioctl+0x9d8/0x30f0
[<ffffff8960de1cac>] snd_pcm_ioctl_compat+0x29c/0x2f14
[<ffffff89604c9d60>] compat_SyS_ioctl+0x128/0x244
[<ffffff8960283740>] el0_svc_naked+0x34/0x38
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If playback and capture are enabled concurrently, when the capture stops
the output becomes inaudile. The playback application will become stuck
and underrun after a timeout.
This is caused by mistaken use of the stream_id, which should only be
set for playback and not for capture
Tested on Apollolake and Kabylake with SST driver.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation of the hdac_hda codec results in zero-valued
samples on capture and noise with headset playback when SOF is used on
platforms with an on-board HDaudio codec. This is root-caused to SOF
using be_hw_params_fixup, and the prepare() call using invalid runtime
fields to determine the format.
This patch moves the format handling to the hw_params() callback, as
done already for hdac_hdmi, to make sure the fixed-up information is
taken into account but keeps the codec initialization in prepare() as
the stream_tag is only available at that time. Moving everything in the
prepare() callback is possible but the code is less elegant so this
two-step solution was chosen.
The solution was tested with the SST driver with no regressions, and all
the issues with SOF playback and capture are solved.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On HDaudio platforms, if playback is started when capture is working,
there is no audible output.
This can be root-caused to the use of the rx|tx_mask to store an HDaudio
stream tag.
If capture is stared before playback, rx_mask would be non-zero on HDaudio
platform, then the channel number of playback, which is in the same codec
dai with the capture, would be changed by soc_pcm_codec_params_fixup based
on the tx_mask at first, then overwritten by this function based on rx_mask
at last.
According to the author of tx|rx_mask, tx_mask is for playback and rx_mask
is for capture. And stream direction is checked at all other references of
tx|rx_mask in ASoC, so here should be an error. This patch checks stream
direction for tx|rx_mask for fixup function.
This issue would affect not only HDaudio+ASoC, but also I2S codecs if the
channel number based on rx_mask is not equal to the one for tx_mask. It could
be rarely reproduecd because most drivers in kernel set the same channel number
to tx|rx_mask or rx_mask is zero.
Tested on all platforms using stream_tag & HDaudio and intel I2S platforms.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets missing stream_name of capture part of the DAI driver
so we can define DAPM routing properly also for the capture stream.
While at it "Playback" suffix is added to the playback stream names
to clearly identify playback/capture.
Together with related dts patch this fixes NULL pointer dereference
when opening ALSA device for recording on Odroid XU3.
Fixes: 64aba9bca5 ("ASoC: samsung: i2s: Add widgets and routes for DPCM support")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI interface implementation was completely broken.
When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.
This fixes that the device wouldn't even probe in SPI mode.
The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.
Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.
The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.
Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The standard unit for temperature is millidegrees Celcius. Adapt the
driver to report in millidegrees instead of degrees.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I clearly messed up applying this patch. Not sure
how but the entire Kconfig block is missing. This
patch puts it back as it was in the original patch.
Reported-by: Andreas Brauchli <a.brauchli@elementarea.net>
Fixes: ce51412416 ("iio: chemical: sgp30: Support Sensirion SGP30/SGPC3 sensors")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet, the last bit of CHIP_ID register controls
I2C bus, and the first one is unused. Handle this correctly.
Note that there are chips out there that have a value such that
the id check currently fails.
Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.
Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit 057ac1acdf ("iio: Use kmalloc_array() in iio_scan_mask_set()").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 78a24e10cd ("ASoC: soc-core: clear platform pointers on error")
re-worked the clean-up of any platform pointers that may have been
initialised by the function snd_soc_init_platform(). This commit missed
one error path where if any of the prelinks for a soundcard failed to
initialise, then these platform pointers would not be cleaned-up. This
then prevents the soundcard from being initialised following a probe
deferral when any of the soundcard prelinks cannot be found.
Fix this by ensuring that soc_cleanup_platform() is called when
initialising the soundcard prelinks fails.
Fixes: 78a24e10cd ("ASoC: soc-core: clear platform pointers on error")
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Limiting the value of the passed in params->msbits in the hw_params()
callback is redundant on three counts:
1. We already specify in the DAI driver that we can only handle up to
24 bits. This means msbits will be limited to 24 via the ALSA
constraints imposed by the ASoC core, unless we have multiple codecs
that can handle more bits.
2. Nothing in our hw_params() implementation uses this value.
3. The copy of the params that we are passed by the ASoC core never
reads back the msbits value.
Consequently, this code is unnecessary and does nothing useful. Remove
it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error check on set_sync function return.
Add of_node_put() as of_get_parent() takes a reference
which has to be released.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When snd_pcm_stop_xrun() is called in interrupt routine,
substream context may have already been released.
Add protection on substream context.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change capabilities exposed in SAI S/PDIF mode, to match
actually supported formats.
In S/PDIF mode only 32 bits stereo is supported.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow indexation of sai iec958 controls according
to device id.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
In file included from sound/soc/codecs/ab8500-codec.c:24:
sound/soc/codecs/ab8500-codec.c: In function ‘ab8500_codec_set_dai_fmt’:
./include/linux/device.h:1485:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/codecs/ab8500-codec.c:2129:3: note: in expansion of macro ‘dev_err’
dev_err(dai->component->dev,
^~~~~~~
sound/soc/codecs/ab8500-codec.c:2132:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the S/PDIF DAI, there is no requirement to call
snd_soc_dai_set_fmt() as there is no DAI format definition that defines
S/PDIF. In any case, S/PDIF does not have separate clocks, this is
embedded into the data stream.
Consequently, when attempting to use TDA998x in S/PDIF mode, the attempt
to configure TDA998x via the hw_params callback fails as the
hdmi_codec_daifmt is left initialised to zero.
Since the S/PDIF DAI will only be used by S/PDIF, prepare the
hdmi_codec_daifmt structure for this format.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes a bug that prevents freeing the reset gpio on unloading
the module.
aic3x_i2c_probe is called when loading the module and it calls list_add
with a probably uninitialized list entry aic3x->list (next = prev = NULL)).
So even if list_del is called it does nothing and in the end the gpio_reset
is not freed. Then a repeated module probing fails silently because
gpio_request fails.
When moving INIT_LIST_HEAD to aic3x_i2c_probe we also have to move
list_del to aic3x_i2c_remove because aic3x_remove may be called
multiple times without aic3x_i2c_remove being called which leads to
a NULL pointer dereference.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2019-02-28 14:15:57 +00:00
642 changed files with 6397 additions and 2914 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
