Linux 4.3-rc3

Pull x86 fixes from Thomas Gleixner:
 "Two bugfixes from Andy addressing at least some of the subtle NMI
  related wreckage which has been reported by Sasha Levin"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
  x86/paravirt: Replace the paravirt nop with a bona fide empty function

Documentation/devicetree/bindings/arm/gic-v3.txt

@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};

Documentation/devicetree/bindings/arm/idle-states.txt

@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";

Documentation/devicetree/bindings/gpio/gpio.txt

@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with

Documentation/devicetree/bindings/iio/accel/bma180.txt

@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.

Documentation/devicetree/bindings/regulator/pbias-regulator.txt

@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };

Documentation/devicetree/bindings/thermal/thermal.txt

@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };

Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt

@@ -6,6 +6,7 @@ Required properties:
 	"lsi,zevio-usb"
 	"qcom,ci-hdrc"
 	"chipidea,usb2"
+	"xlnx,zynq-usb-2.20a"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation

Documentation/networking/vrf.txt

@@ -0,0 +1,96 @@
+Virtual Routing and Forwarding (VRF)
+====================================
+The VRF device combined with ip rules provides the ability to create virtual
+routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the
+Linux network stack. One use case is the multi-tenancy problem where each
+tenant has their own unique routing tables and in the very least need
+different default gateways.
+
+Processes can be "VRF aware" by binding a socket to the VRF device. Packets
+through the socket then use the routing table associated with the VRF
+device. An important feature of the VRF device implementation is that it
+impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected
+(ie., they do not need to be run in each VRF). The design also allows
+the use of higher priority ip rules (Policy Based Routing, PBR) to take
+precedence over the VRF device rules directing specific traffic as desired.
+
+In addition, VRF devices allow VRFs to be nested within namespaces. For
+example network namespaces provide separation of network interfaces at L1
+(Layer 1 separation), VLANs on the interfaces within a namespace provide
+L2 separation and then VRF devices provide L3 separation.
+
+Design
+------
+A VRF device is created with an associated route table. Network interfaces
+are then enslaved to a VRF device:
+
+         +-----------------------------+
+         |           vrf-blue          |  ===> route table 10
+         +-----------------------------+
+            |        |            |
+         +------+ +------+     +-------------+
+         | eth1 | | eth2 | ... |    bond1    |
+         +------+ +------+     +-------------+
+                                  |       |
+                              +------+ +------+
+                              | eth8 | | eth9 |
+                              +------+ +------+
+
+Packets received on an enslaved device and are switched to the VRF device
+using an rx_handler which gives the impression that packets flow through
+the VRF device. Similarly on egress routing rules are used to send packets
+to the VRF device driver before getting sent out the actual interface. This
+allows tcpdump on a VRF device to capture all packets into and out of the
+VRF as a whole.[1] Similiarly, netfilter [2] and tc rules can be applied
+using the VRF device to specify rules that apply to the VRF domain as a whole.
+
+[1] Packets in the forwarded state do not flow through the device, so those
+    packets are not seen by tcpdump. Will revisit this limitation in a
+    future release.
+
+[2] Iptables on ingress is limited to NF_INET_PRE_ROUTING only with skb->dev
+    set to real ingress device and egress is limited to NF_INET_POST_ROUTING.
+    Will revisit this limitation in a future release.
+
+
+Setup
+-----
+1. VRF device is created with an association to a FIB table.
+   e.g, ip link add vrf-blue type vrf table 10
+        ip link set dev vrf-blue up
+
+2. Rules are added that send lookups to the associated FIB table when the
+   iif or oif is the VRF device. e.g.,
+       ip ru add oif vrf-blue table 10
+       ip ru add iif vrf-blue table 10
+
+   Set the default route for the table (and hence default route for the VRF).
+   e.g, ip route add table 10 prohibit default
+
+3. Enslave L3 interfaces to a VRF device.
+   e.g,  ip link set dev eth1 master vrf-blue
+
+   Local and connected routes for enslaved devices are automatically moved to
+   the table associated with VRF device. Any additional routes depending on
+   the enslaved device will need to be reinserted following the enslavement.
+
+4. Additional VRF routes are added to associated table.
+   e.g., ip route add table 10 ...
+
+
+Applications
+------------
+Applications that are to work within a VRF need to bind their socket to the
+VRF device:
+
+    setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1);
+
+or to specify the output device using cmsg and IP_PKTINFO.
+
+
+Limitations
+-----------
+VRF device currently only works for IPv4. Support for IPv6 is under development.
+
+Index of original ingress interface is not available via cmsg. Will address
+soon.

Documentation/sysctl/net.txt

@@ -54,13 +54,15 @@ default_qdisc
 --------------
 
 The default queuing discipline to use for network devices. This allows
-overriding the default queue discipline of pfifo_fast with an
-alternative. Since the default queuing discipline is created with the
-no additional parameters so is best suited to queuing disciplines that
-work well without configuration like stochastic fair queue (sfq),
-CoDel (codel) or fair queue CoDel (fq_codel). Don't use queuing disciplines
-like Hierarchical Token Bucket or Deficit Round Robin which require setting
-up classes and bandwidths.
+overriding the default of pfifo_fast with an alternative. Since the default
+queuing discipline is created without additional parameters so is best suited
+to queuing disciplines that work well without configuration like stochastic
+fair queue (sfq), CoDel (codel) or fair queue CoDel (fq_codel). Don't use
+queuing disciplines like Hierarchical Token Bucket or Deficit Round Robin
+which require setting up classes and bandwidths. Note that physical multiqueue
+interfaces still use mq as root qdisc, which in turn uses this default for its
+leaves. Virtual devices (like e.g. lo or veth) ignore this setting and instead
+default to noqueue.
 Default: pfifo_fast
 
 busy_read

Documentation/thermal/power_allocator.txt

@@ -4,7 +4,7 @@ Power allocator governor tunables
 Trip points
 -----------
 
-The governor requires the following two passive trip points:
+The governor works optimally with the following two passive trip points:
 
 1.  "switch on" trip point: temperature above which the governor
     control loop starts operating.  This is the first passive trip

MAINTAINERS

@@ -615,9 +615,8 @@ F:	Documentation/hwmon/fam15h_power
 F:	drivers/hwmon/fam15h_power.c
 
 AMD GEODE CS5536 USB DEVICE CONTROLLER DRIVER
-M:	Thomas Dahlmann <dahlmann.thomas@arcor.de>
 L:	linux-geode@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Orphan
 F:	drivers/usb/gadget/udc/amd5536udc.*
 
 AMD GEODE PROCESSOR/CHIPSET SUPPORT
@@ -808,6 +807,13 @@ S:	Maintained
 F:	drivers/video/fbdev/arcfb.c
 F:	drivers/video/fbdev/core/fb_defio.c
 
+ARCNET NETWORK LAYER
+M:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/arcnet/
+F:	include/uapi/linux/if_arcnet.h
+
 ARM MFM AND FLOPPY DRIVERS
 M:	Ian Molton <spyro@f2s.com>
 S:	Maintained
@@ -3394,7 +3400,6 @@ F:	drivers/staging/dgnc/
 
 DIGI EPCA PCI PRODUCTS
 M:	Lidza Louina <lidza.louina@gmail.com>
-M:	Mark Hounschell <markh@compro.net>
 M:	Daeseok Youn <daeseok.youn@gmail.com>
 L:	driverdev-devel@linuxdriverproject.org
 S:	Maintained
@@ -8500,7 +8505,6 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/ethernet/qlogic/qla3xxx.*
 
 QLOGIC QLCNIC (1/10)Gb ETHERNET DRIVER
-M:	Shahed Shaikh <shahed.shaikh@qlogic.com>
 M:	Dept-GELinuxNICDev@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -9904,8 +9908,8 @@ F:	drivers/staging/media/lirc/
 STAGING - LUSTRE PARALLEL FILESYSTEM
 M:	Oleg Drokin <oleg.drokin@intel.com>
 M:	Andreas Dilger <andreas.dilger@intel.com>
-L:	HPDD-discuss@lists.01.org (moderated for non-subscribers)
-W:	http://lustre.opensfs.org/
+L:	lustre-devel@lists.lustre.org (moderated for non-subscribers)
+W:	http://wiki.lustre.org/
 S:	Maintained
 F:	drivers/staging/lustre
 
@@ -10338,6 +10342,16 @@ F:	include/uapi/linux/thermal.h
 F:	include/linux/cpu_cooling.h
 F:	Documentation/devicetree/bindings/thermal/
 
+THERMAL/CPU_COOLING
+M:	Amit Daniel Kachhap <amit.kachhap@gmail.com>
+M:	Viresh Kumar <viresh.kumar@linaro.org>
+M:	Javi Merino <javi.merino@arm.com>
+L:	linux-pm@vger.kernel.org
+S:	Supported
+F:	Documentation/thermal/cpu-cooling-api.txt
+F:	drivers/thermal/cpu_cooling.c
+F:	include/linux/cpu_cooling.h
+
 THINGM BLINK(1) USB RGB LED DRIVER
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 S:	Maintained
@@ -11187,7 +11201,7 @@ F:	drivers/vlynq/vlynq.c
 F:	include/linux/vlynq.h
 
 VME SUBSYSTEM
-M:	Martyn Welch <martyn.welch@ge.com>
+M:	Martyn Welch <martyn@welchs.me.uk>
 M:	Manohar Vanga <manohar.vanga@gmail.com>
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	devel@driverdev.osuosl.org
@@ -11239,7 +11253,6 @@ VOLTAGE AND CURRENT REGULATOR FRAMEWORK
 M:	Liam Girdwood <lgirdwood@gmail.com>
 M:	Mark Brown <broonie@kernel.org>
 L:	linux-kernel@vger.kernel.org
-W:	http://opensource.wolfsonmicro.com/node/15
 W:	http://www.slimlogic.co.uk/?p=48
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
 S:	Supported
@@ -11253,6 +11266,7 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/vrf.c
 F:	include/net/vrf.h
+F:	Documentation/networking/vrf.txt
 
 VT1211 HARDWARE MONITOR DRIVER
 M:	Juerg Haefliger <juergh@gmail.com>
@@ -11368,17 +11382,15 @@ WM97XX TOUCHSCREEN DRIVERS
 M:	Mark Brown <broonie@kernel.org>
 M:	Liam Girdwood <lrg@slimlogic.co.uk>
 L:	linux-input@vger.kernel.org
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
-W:	http://opensource.wolfsonmicro.com/node/7
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	drivers/input/touchscreen/*wm97*
 F:	include/linux/wm97xx.h
 
 WOLFSON MICROELECTRONICS DRIVERS
 L:	patches@opensource.wolfsonmicro.com
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-asoc
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
-W:	http://opensource.wolfsonmicro.com/content/linux-drivers-wolfson-devices
+T:	git https://github.com/CirrusLogic/linux-drivers.git
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	arch/arm/mach-s3c64xx/mach-crag6410*

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/alpha/kernel/pci.c

@@ -242,7 +242,12 @@ pci_restore_srm_config(void)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	struct pci_dev *dev;
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		pdev_save_srm_config(dev);

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -252,10 +252,10 @@
 		};
 
 		vdd1_reg: regulator@2 {
-			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			/* VDD_MPU voltage limits 0.95V - 1.325V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1312500>;
+			regulator-max-microvolt = <1378000>;
 			regulator-boot-on;
 			regulator-always-on;
 		};

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -98,13 +98,6 @@
 		pinctrl-0 = <&extcon_usb1_pins>;
 	};
 
-	extcon_usb2: extcon_usb2 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&extcon_usb2_pins>;
-	};
-
 	hdmi0: connector {
 		compatible = "hdmi-connector";
 		label = "hdmi";
@@ -326,12 +319,6 @@
 		>;
 	};
 
-	extcon_usb2_pins: extcon_usb2_pins {
-		pinctrl-single,pins = <
-			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
-		>;
-	};
-
 	tpd12s015_pins: pinmux_tpd12s015_pins {
 		pinctrl-single,pins = <
 			0x3b0 (PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
@@ -432,7 +419,7 @@
 				};
 
 				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHY */
+					/* VDDA_1V8_PHYA */
 					regulator-name = "ldo3";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -440,6 +427,15 @@
 					regulator-boot-on;
 				};
 
+				ldo4_reg: ldo4 {
+					/* VDDA_1V8_PHYB */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
 				ldo9_reg: ldo9 {
 					/* VDD_RTC */
 					regulator-name = "ldo9";
@@ -495,6 +491,14 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
+
+		extcon_usb2: tps659038_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+		};
+
 	};
 
 	tmp102: tmp102@48 {
@@ -517,7 +521,8 @@
 	mcp_rtc: rtc@6f {
 		compatible = "microchip,mcp7941x";
 		reg = <0x6f>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
+		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
+				      <&dra7_pmx_core 0x424>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;
@@ -579,7 +584,6 @@
 	pinctrl-0 = <&mmc1_pins_default>;
 
 	vmmc-supply = <&ldo1_reg>;
-	vmmc_aux-supply = <&vdd_3v3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
 };
@@ -623,6 +627,14 @@
 };
 
 &usb2 {
+	/*
+	 * Stand alone usage is peripheral only.
+	 * However, with some resistor modifications
+	 * this port can be used via expansion connectors
+	 * as "host" or "dual-role". If so, provide
+	 * the necessary dr_mode override in the expansion
+	 * board's DT.
+	 */
 	dr_mode = "peripheral";
 };
 
@@ -681,7 +693,7 @@
 
 &hdmi {
 	status = "ok";
-	vdda-supply = <&ldo3_reg>;
+	vdda-supply = <&ldo4_reg>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_pins>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm8148-t410.dts

@@ -8,7 +8,7 @@
 #include "dm814x.dtsi"
 
 / {
-	model = "DM8148 EVM";
+	model = "HP t410 Smart Zero Client";
 	compatible = "hp,t410", "ti,dm8148";
 
 	memory {
@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm814x.dtsi

@@ -181,9 +181,9 @@
 				ti,hwmods = "timer3";
 			};
 
-			control: control@160000 {
+			control: control@140000 {
 				compatible = "ti,dm814-scm", "simple-bus";
-				reg = <0x160000 0x16d000>;
+				reg = <0x140000 0x16d000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x160000 0x16d000>;
@@ -321,9 +321,9 @@
 				mac-address = [ 00 00 00 00 00 00 ];
 			};
 
-			phy_sel: cpsw-phy-sel@0x48160650 {
+			phy_sel: cpsw-phy-sel@48140650 {
 				compatible = "ti,am3352-cpsw-phy-sel";
-				reg= <0x48160650 0x4>;
+				reg= <0x48140650 0x4>;
 				reg-names = "gmii-sel";
 			};
 		};

arch/arm/boot/dts/dra7.dtsi

@@ -120,9 +120,10 @@
 					reg = <0x0 0x1400>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x0 0x1400>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-dra7", "ti,pbias-omap";
 						reg = <0xe00 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap5 {
@@ -1417,7 +1418,7 @@
 			ti,irqs-safe-map = <0>;
 		};
 
-		mac: ethernet@4a100000 {
+		mac: ethernet@48484000 {
 			compatible = "ti,dra7-cpsw","ti,cpsw";
 			ti,hwmods = "gmac";
 			clocks = <&dpll_gmac_ck>, <&gmac_gmii_ref_clk_div>;

arch/arm/boot/dts/omap2430.dtsi

@@ -56,6 +56,7 @@
 					reg = <0x270 0x240>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x240>;
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -63,7 +64,7 @@
 					};
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap2", "ti,pbias-omap";
 						reg = <0x230 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap2430 {

arch/arm/boot/dts/omap3-beagle.dts

@@ -202,7 +202,7 @@
 
 	tfp410_pins: pinmux_tfp410_pins {
 		pinctrl-single,pins = <
-			0x194 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
+			0x196 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
 		>;
 	};
 

arch/arm/boot/dts/omap3-igep.dtsi

@@ -78,12 +78,6 @@
 		>;
 	};
 
-	smsc9221_pins: pinmux_smsc9221_pins {
-		pinctrl-single,pins = <
-			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
-		>;
-	};
-
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0x18a (PIN_INPUT | MUX_MODE0)   /* i2c1_scl.i2c1_scl */

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -156,6 +156,12 @@
 			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
 		>;
 	};
+
+	smsc9221_pins: pinmux_smsc9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4)	/* mcspi1_cs2.gpio_176 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/omap3.dtsi

@@ -113,10 +113,22 @@
 				};
 
 				scm_conf: scm_conf@270 {
-					compatible = "syscon";
+					compatible = "syscon", "simple-bus";
 					reg = <0x270 0x330>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x330>;
+
+					pbias_regulator: pbias_regulator {
+						compatible = "ti,pbias-omap3", "ti,pbias-omap";
+						reg = <0x2b0 0x4>;
+						syscon = <&scm_conf>;
+						pbias_mmc_reg: pbias_mmc_omap2430 {
+							regulator-name = "pbias_mmc_omap2430";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <3000000>;
+						};
+					};
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -202,17 +214,6 @@
 			dma-requests = <96>;
 		};
 
-		pbias_regulator: pbias_regulator {
-			compatible = "ti,pbias-omap";
-			reg = <0x2b0 0x4>;
-			syscon = <&scm_conf>;
-			pbias_mmc_reg: pbias_mmc_omap2430 {
-				regulator-name = "pbias_mmc_omap2430";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3000000>;
-			};
-		};
-
 		gpio1: gpio@48310000 {
 			compatible = "ti,omap3-gpio";
 			reg = <0x48310000 0x200>;

arch/arm/boot/dts/omap4.dtsi

@@ -196,9 +196,10 @@
 					reg = <0x5a0 0x170>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0x170>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap4", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap4_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap4 {

arch/arm/boot/dts/omap5-uevm.dts

@@ -174,8 +174,8 @@
 
 	i2c5_pins: pinmux_i2c5_pins {
 		pinctrl-single,pins = <
-			0x184 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
-			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
+			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
+			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
 		>;
 	};
 

arch/arm/boot/dts/omap5.dtsi

@@ -185,9 +185,10 @@
 					reg = <0x5a0 0xec>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0xec>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap5", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap5_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap5 {

arch/arm/boot/dts/rk3288-veyron.dtsi

@@ -158,6 +158,7 @@
 };
 
 &hdmi {
+	ddc-i2c-bus = <&i2c5>;
 	status = "okay";
 };
 

arch/arm/boot/dts/stih407.dtsi

@@ -103,48 +103,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
+			};
 
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
 
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
 
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 	};

arch/arm/boot/dts/stih410.dtsi

@@ -178,48 +178,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
+			};
 
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
 
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
 
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 

arch/arm/configs/omap2plus_defconfig

@@ -240,7 +240,8 @@ CONFIG_SSI_PROTOCOL=m
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
-CONFIG_GPIO_PCF857X=m
+CONFIG_GPIO_PCA953X=m
+CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_TWL4030=y
 CONFIG_GPIO_PALMAS=y
 CONFIG_W1=m
@@ -350,6 +351,8 @@ CONFIG_USB_MUSB_HDRC=m
 CONFIG_USB_MUSB_OMAP2PLUS=m
 CONFIG_USB_MUSB_AM35X=m
 CONFIG_USB_MUSB_DSPS=m
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=m
 CONFIG_AM335X_PHY_USB=y

arch/arm/include/asm/kvm_host.h

@@ -33,6 +33,7 @@
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 #define KVM_HAVE_ONE_REG
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #define KVM_VCPU_MAX_FEATURES 2
 

arch/arm/include/asm/unistd.h

@@ -19,7 +19,7 @@
  * This may need to be greater than __NR_last_syscall+1 in order to
  * account for the padding in the syscall table
  */
-#define __NR_syscalls  (388)
+#define __NR_syscalls  (392)
 
 /*
  * *NOTE*: This is a ghost syscall private to the kernel.  Only the

arch/arm/include/uapi/asm/unistd.h

@@ -414,6 +414,8 @@
 #define __NR_memfd_create		(__NR_SYSCALL_BASE+385)
 #define __NR_bpf			(__NR_SYSCALL_BASE+386)
 #define __NR_execveat			(__NR_SYSCALL_BASE+387)
+#define __NR_userfaultfd		(__NR_SYSCALL_BASE+388)
+#define __NR_membarrier			(__NR_SYSCALL_BASE+389)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/calls.S

@@ -397,6 +397,8 @@
 /* 385 */	CALL(sys_memfd_create)
 		CALL(sys_bpf)
 		CALL(sys_execveat)
+		CALL(sys_userfaultfd)
+		CALL(sys_membarrier)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/mach-omap2/Kconfig

@@ -44,10 +44,11 @@ config SOC_OMAP5
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
-	select HAVE_ARM_TWD if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config SOC_AM33XX
 	bool "TI AM33XX"
@@ -70,10 +71,13 @@ config SOC_DRA7XX
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
+	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select IRQ_CROSSBAR
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config ARCH_OMAP2PLUS
 	bool

arch/arm/mach-omap2/board-generic.c

@@ -20,13 +20,6 @@
 
 #include "common.h"
 
-#if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
-#define intc_of_init	NULL
-#endif
-#ifndef CONFIG_ARCH_OMAP4
-#define gic_of_init		NULL
-#endif
-
 static const struct of_device_id omap_dt_match_table[] __initconst = {
 	{ .compatible = "simple-bus", },
 	{ .compatible = "ti,omap-infra", },

arch/arm/mach-omap2/id.c

@@ -653,8 +653,12 @@ void __init dra7xxx_check_revision(void)
 			omap_revision = DRA752_REV_ES1_0;
 			break;
 		case 1:
-		default:
 			omap_revision = DRA752_REV_ES1_1;
+			break;
+		case 2:
+		default:
+			omap_revision = DRA752_REV_ES2_0;
+			break;
 		}
 		break;
 
@@ -674,7 +678,7 @@ void __init dra7xxx_check_revision(void)
 		/* Unknown default to latest silicon rev as default*/
 		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
 			__func__, idcode, hawkeye, rev);
-		omap_revision = DRA752_REV_ES1_1;
+		omap_revision = DRA752_REV_ES2_0;
 	}
 
 	sprintf(soc_name, "DRA%03x", omap_rev() >> 16);

arch/arm/mach-omap2/io.c

@@ -676,6 +676,7 @@ void __init am43xx_init_early(void)
 void __init am43xx_init_late(void)
 {
 	omap_common_late_init();
+	omap2_clk_enable_autoidle_all();
 }
 #endif
 

arch/arm/mach-omap2/omap_device.c

@@ -901,7 +901,8 @@ static int __init omap_device_late_idle(struct device *dev, void *data)
 		if (od->hwmods[i]->flags & HWMOD_INIT_NO_IDLE)
 			return 0;
 
-	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) {
+	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER &&
+	    od->_driver_status != BUS_NOTIFY_BIND_DRIVER) {
 		if (od->_state == OMAP_DEVICE_STATE_ENABLED) {
 			dev_warn(dev, "%s: enabled but no driver.  Idling\n",
 				 __func__);

arch/arm/mach-omap2/pm.h

@@ -103,7 +103,8 @@ static inline void enable_omap3630_toggle_l2_on_restore(void) { }
 #define PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD	(1 << 0)
 #define PM_OMAP4_CPU_OSWR_DISABLE		(1 << 1)
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_PM) && (defined(CONFIG_ARCH_OMAP4) ||\
+	   defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX))
 extern u16 pm44xx_errata;
 #define IS_PM44XX_ERRATUM(id)		(pm44xx_errata & (id))
 #else

arch/arm/mach-omap2/soc.h

@@ -469,6 +469,8 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define DRA7XX_CLASS		0x07000000
 #define DRA752_REV_ES1_0	(DRA7XX_CLASS | (0x52 << 16) | (0x10 << 8))
 #define DRA752_REV_ES1_1	(DRA7XX_CLASS | (0x52 << 16) | (0x11 << 8))
+#define DRA752_REV_ES2_0	(DRA7XX_CLASS | (0x52 << 16) | (0x20 << 8))
+#define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 #define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 
 void omap2xxx_check_revision(void);

arch/arm/mach-omap2/timer.c

@@ -297,12 +297,8 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
 	if (IS_ERR(src))
 		return PTR_ERR(src);
 
-	r = clk_set_parent(timer->fclk, src);
-	if (r < 0) {
-		pr_warn("%s: %s cannot set source\n", __func__, oh->name);
-		clk_put(src);
-		return r;
-	}
+	WARN(clk_set_parent(timer->fclk, src) < 0,
+	     "Cannot set timer parent clock, no PLL clock driver?");
 
 	clk_put(src);
 

arch/arm/mach-omap2/vc.c

@@ -300,7 +300,7 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
 
 	val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET);
 	if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) ||
-	    (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) {
+	    (val & OMAP3430_PRM_POLCTRL_OFFMODE_POL)) {
 		val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
 		val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
 		pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n",

arch/arm/mach-pxa/balloon3.c

@@ -502,7 +502,7 @@ static void balloon3_irq_handler(struct irq_desc *desc)
 					balloon3_irq_enabled;
 	do {
 		struct irq_data *d = irq_desc_get_irq_data(desc);
-		struct irq_chip *chip = irq_data_get_chip(d);
+		struct irq_chip *chip = irq_desc_get_chip(desc);
 		unsigned int irq;
 
 		/* clear useless edge notification */

arch/arm/mach-pxa/include/mach/addr-map.h

@@ -43,6 +43,13 @@
  * 0xf6200000..0xf6201000
  */
 
+/*
+ * DFI Bus for NAND, PXA3xx only
+ */
+#define NAND_PHYS		0x43100000
+#define NAND_VIRT		IOMEM(0xf6300000)
+#define NAND_SIZE		0x00100000
+
 /*
  * Internal Memory Controller (PXA27x and later)
  */

arch/arm/mach-pxa/pxa3xx.c

@@ -47,6 +47,13 @@ extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
 #define ISRAM_START	0x5c000000
 #define ISRAM_SIZE	SZ_256K
 
+/*
+ * NAND NFC: DFI bus arbitration subset
+ */
+#define NDCR			(*(volatile u32 __iomem*)(NAND_VIRT + 0))
+#define NDCR_ND_ARB_EN		(1 << 12)
+#define NDCR_ND_ARB_CNTL	(1 << 19)
+
 static void __iomem *sram;
 static unsigned long wakeup_src;
 
@@ -362,7 +369,12 @@ static struct map_desc pxa3xx_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(PXA3XX_SMEMC_BASE),
 		.length		= SMEMC_SIZE,
 		.type		= MT_DEVICE
-	}
+	}, {
+		.virtual	= (unsigned long)NAND_VIRT,
+		.pfn		= __phys_to_pfn(NAND_PHYS),
+		.length		= NAND_SIZE,
+		.type		= MT_DEVICE
+	},
 };
 
 void __init pxa3xx_map_io(void)
@@ -419,6 +431,13 @@ static int __init pxa3xx_init(void)
 		 */
 		ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S);
 
+		/*
+		 * Disable DFI bus arbitration, to prevent a system bus lock if
+		 * somebody disables the NAND clock (unused clock) while this
+		 * bit remains set.
+		 */
+		NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
+
 		if ((ret = pxa_init_dma(IRQ_DMA, 32)))
 			return ret;
 

arch/arm/mm/alignment.c

@@ -365,15 +365,21 @@ do_alignment_ldrhstrh(unsigned long addr, unsigned long instr, struct pt_regs *r
  user:
 	if (LDST_L_BIT(instr)) {
 		unsigned long val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get16t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 
 		/* signed half-word? */
 		if (instr & 0x40)
 			val = (signed long)((signed short) val);
 
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put16t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 
 	return TYPE_LDST;
 
@@ -420,14 +426,21 @@ do_alignment_ldrdstrd(unsigned long addr, unsigned long instr,
 
  user:
 	if (load) {
-		unsigned long val;
+		unsigned long val, val2;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get32t_unaligned_check(val, addr);
+		get32t_unaligned_check(val2, addr + 4);
+
+		uaccess_restore(__ua_flags);
+
 		regs->uregs[rd] = val;
-		get32t_unaligned_check(val, addr + 4);
-		regs->uregs[rd2] = val;
+		regs->uregs[rd2] = val2;
 	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
 		put32t_unaligned_check(regs->uregs[rd2], addr + 4);
+		uaccess_restore(__ua_flags);
 	}
 
 	return TYPE_LDST;
@@ -458,10 +471,15 @@ do_alignment_ldrstr(unsigned long addr, unsigned long instr, struct pt_regs *reg
  trans:
 	if (LDST_L_BIT(instr)) {
 		unsigned int val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		get32t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 	return TYPE_LDST;
 
  fault:
@@ -531,6 +549,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 #endif
 
 	if (user_mode(regs)) {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)
 			if (regbits & 1) {
@@ -542,6 +561,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 					put32t_unaligned_check(regs->uregs[rd], eaddr);
 				eaddr += 4;
 			}
+		uaccess_restore(__ua_flags);
 	} else {
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)

arch/arm/plat-pxa/ssp.c

@@ -107,7 +107,6 @@ static const struct of_device_id pxa_ssp_of_ids[] = {
 	{ .compatible = "mvrl,pxa168-ssp",	.data = (void *) PXA168_SSP },
 	{ .compatible = "mrvl,pxa910-ssp",	.data = (void *) PXA910_SSP },
 	{ .compatible = "mrvl,ce4100-ssp",	.data = (void *) CE4100_SSP },
-	{ .compatible = "mrvl,lpss-ssp",	.data = (void *) LPSS_SSP },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids);

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -81,7 +81,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			CPU_SLEEP_0: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -106,7 +106,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			cpu_sleep: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/include/asm/kvm_host.h

@@ -33,6 +33,7 @@
 #define KVM_USER_MEM_SLOTS 32
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #include <kvm/arm_vgic.h>
 #include <kvm/arm_arch_timer.h>

arch/frv/mb93090-mb00/pci-vdk.c

@@ -294,6 +294,8 @@ void pcibios_fixup_bus(struct pci_bus *bus)
 	printk("### PCIBIOS_FIXUP_BUS(%d)\n",bus->number);
 #endif
 
+	pci_read_bridge_bases(bus);
+
 	if (bus->number == 0) {
 		struct pci_dev *dev;
 		list_for_each_entry(dev, &bus->devices, bus_list) {

arch/ia64/pci/pci.c

@@ -533,9 +533,10 @@ void pcibios_fixup_bus(struct pci_bus *b)
 {
 	struct pci_dev *dev;
 
-	if (b->self)
+	if (b->self) {
+		pci_read_bridge_bases(b);
 		pcibios_fixup_bridge_resources(b->self);
-
+	}
 	list_for_each_entry(dev, &b->devices, bus_list)
 		pcibios_fixup_device_resources(dev);
 	platform_pci_fixup_bus(b);

arch/microblaze/pci/pci-common.c

@@ -863,7 +863,14 @@ void pcibios_setup_bus_devices(struct pci_bus *bus)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	/* Fixup the bus */
+	/* When called from the generic PCI probe, read PCI<->PCI bridge
+	 * bases. This is -not- called when generating the PCI tree from
+	 * the OF device-tree.
+	 */
+	if (bus->self != NULL)
+		pci_read_bridge_bases(bus);
+
+	/* Now fixup the bus bus */
 	pcibios_setup_bus_self(bus);
 
 	/* Now fixup devices on that bus */

arch/mips/include/asm/kvm_host.h

@@ -61,6 +61,7 @@
 #define KVM_PRIVATE_MEM_SLOTS 	0
 
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 
 

arch/mips/pci/pci.c

@@ -311,6 +311,12 @@ int pcibios_enable_device(struct pci_dev *dev, int mask)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
 }
 
 EXPORT_SYMBOL(PCIBIOS_MIN_IO);

arch/mn10300/unit-asb2305/pci.c

@@ -324,6 +324,7 @@ void pcibios_fixup_bus(struct pci_bus *bus)
 	struct pci_dev *dev;
 
 	if (bus->self) {
+		pci_read_bridge_bases(bus);
 		pcibios_fixup_bridge_resources(bus->self);
 	}
 

arch/powerpc/include/asm/kvm_host.h

@@ -44,6 +44,7 @@
 #ifdef CONFIG_KVM_MMIO
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 #endif
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 /* These values are internal and can be increased later */
 #define KVM_NR_IRQCHIPS          1

arch/powerpc/include/asm/systbl.h

@@ -369,3 +369,4 @@ SYSCALL_SPU(bpf)
 COMPAT_SYS(execveat)
 PPC64ONLY(switch_endian)
 SYSCALL_SPU(userfaultfd)
+SYSCALL_SPU(membarrier)

arch/powerpc/include/asm/unistd.h

@@ -12,7 +12,7 @@
 #include <uapi/asm/unistd.h>
 
 
-#define __NR_syscalls		365
+#define __NR_syscalls		366
 
 #define __NR__exit __NR_exit
 #define NR_syscalls	__NR_syscalls

arch/powerpc/include/uapi/asm/unistd.h

@@ -387,5 +387,6 @@
 #define __NR_execveat		362
 #define __NR_switch_endian	363
 #define __NR_userfaultfd	364
+#define __NR_membarrier		365
 
 #endif /* _UAPI_ASM_POWERPC_UNISTD_H_ */

arch/powerpc/kernel/pci-common.c

@@ -1032,7 +1032,13 @@ void pcibios_set_master(struct pci_dev *dev)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	/* Fixup the bus */
+	/* When called from the generic PCI probe, read PCI<->PCI bridge
+	 * bases. This is -not- called when generating the PCI tree from
+	 * the OF device-tree.
+	 */
+	pci_read_bridge_bases(bus);
+
+	/* Now fixup the bus bus */
 	pcibios_setup_bus_self(bus);
 
 	/* Now fixup devices on that bus */

arch/powerpc/kvm/book3s.c

@@ -829,12 +829,15 @@ int kvmppc_h_logical_ci_load(struct kvm_vcpu *vcpu)
 	unsigned long size = kvmppc_get_gpr(vcpu, 4);
 	unsigned long addr = kvmppc_get_gpr(vcpu, 5);
 	u64 buf;
+	int srcu_idx;
 	int ret;
 
 	if (!is_power_of_2(size) || (size > sizeof(buf)))
 		return H_TOO_HARD;
 
+	srcu_idx = srcu_read_lock(&vcpu->kvm->srcu);
 	ret = kvm_io_bus_read(vcpu, KVM_MMIO_BUS, addr, size, &buf);
+	srcu_read_unlock(&vcpu->kvm->srcu, srcu_idx);
 	if (ret != 0)
 		return H_TOO_HARD;
 
@@ -869,6 +872,7 @@ int kvmppc_h_logical_ci_store(struct kvm_vcpu *vcpu)
 	unsigned long addr = kvmppc_get_gpr(vcpu, 5);
 	unsigned long val = kvmppc_get_gpr(vcpu, 6);
 	u64 buf;
+	int srcu_idx;
 	int ret;
 
 	switch (size) {
@@ -892,7 +896,9 @@ int kvmppc_h_logical_ci_store(struct kvm_vcpu *vcpu)
 		return H_TOO_HARD;
 	}
 
+	srcu_idx = srcu_read_lock(&vcpu->kvm->srcu);
 	ret = kvm_io_bus_write(vcpu, KVM_MMIO_BUS, addr, size, &buf);
+	srcu_read_unlock(&vcpu->kvm->srcu, srcu_idx);
 	if (ret != 0)
 		return H_TOO_HARD;
 

arch/powerpc/kvm/book3s_hv.c

@@ -2692,9 +2692,13 @@ static int kvmppc_run_vcpu(struct kvm_run *kvm_run, struct kvm_vcpu *vcpu)
 
 	while (vcpu->arch.state == KVMPPC_VCPU_RUNNABLE &&
 	       (vc->vcore_state == VCORE_RUNNING ||
-		vc->vcore_state == VCORE_EXITING))
+		vc->vcore_state == VCORE_EXITING ||
+		vc->vcore_state == VCORE_PIGGYBACK))
 		kvmppc_wait_for_exec(vc, vcpu, TASK_UNINTERRUPTIBLE);
 
+	if (vc->vcore_state == VCORE_PREEMPT && vc->runner == NULL)
+		kvmppc_vcore_end_preempt(vc);
+
 	if (vcpu->arch.state == KVMPPC_VCPU_RUNNABLE) {
 		kvmppc_remove_runnable(vc, vcpu);
 		vcpu->stat.signal_exits++;

arch/powerpc/kvm/book3s_hv_rmhandlers.S

@@ -1257,6 +1257,7 @@ mc_cont:
 	bl	kvmhv_accumulate_time
 #endif
 
+	mr 	r3, r12
 	/* Increment exit count, poke other threads to exit */
 	bl	kvmhv_commence_exit
 	nop

arch/s390/configs/zfcpdump_defconfig

@@ -1,7 +1,6 @@
 # CONFIG_SWAP is not set
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
-CONFIG_RCU_FAST_NO_HZ=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 # CONFIG_COMPAT_BRK is not set
@@ -54,10 +53,6 @@ CONFIG_RAW_DRIVER=y
 # CONFIG_MONWRITER is not set
 # CONFIG_S390_VMUR is not set
 # CONFIG_HID is not set
-CONFIG_MEMSTICK=y
-CONFIG_MEMSTICK_DEBUG=y
-CONFIG_MEMSTICK_UNSAFE_RESUME=y
-CONFIG_MSPRO_BLOCK=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y

arch/s390/include/asm/kvm_host.h

@@ -35,6 +35,7 @@
  */
 #define KVM_NR_IRQCHIPS 1
 #define KVM_IRQCHIP_NUM_PINS 4096
+#define KVM_HALT_POLL_NS_DEFAULT 0
 
 #define SIGP_CTRL_C		0x80
 #define SIGP_CTRL_SCN_MASK	0x3f

arch/s390/include/asm/unistd.h

@@ -8,28 +8,8 @@
 
 #include <uapi/asm/unistd.h>
 
-
 #define __IGNORE_time
 
-/* Ignore system calls that are also reachable via sys_socketcall */
-#define __IGNORE_recvmmsg
-#define __IGNORE_sendmmsg
-#define __IGNORE_socket
-#define __IGNORE_socketpair
-#define __IGNORE_bind
-#define __IGNORE_connect
-#define __IGNORE_listen
-#define __IGNORE_accept4
-#define __IGNORE_getsockopt
-#define __IGNORE_setsockopt
-#define __IGNORE_getsockname
-#define __IGNORE_getpeername
-#define __IGNORE_sendto
-#define __IGNORE_sendmsg
-#define __IGNORE_recvfrom
-#define __IGNORE_recvmsg
-#define __IGNORE_shutdown
-
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_SYS_ALARM
 #define __ARCH_WANT_SYS_GETHOSTNAME

arch/s390/include/uapi/asm/unistd.h

@@ -290,7 +290,26 @@
 #define __NR_s390_pci_mmio_write	352
 #define __NR_s390_pci_mmio_read		353
 #define __NR_execveat		354
-#define NR_syscalls 355
+#define __NR_userfaultfd	355
+#define __NR_membarrier		356
+#define __NR_recvmmsg		357
+#define __NR_sendmmsg		358
+#define __NR_socket		359
+#define __NR_socketpair		360
+#define __NR_bind		361
+#define __NR_connect		362
+#define __NR_listen		363
+#define __NR_accept4		364
+#define __NR_getsockopt		365
+#define __NR_setsockopt		366
+#define __NR_getsockname	367
+#define __NR_getpeername	368
+#define __NR_sendto		369
+#define __NR_sendmsg		370
+#define __NR_recvfrom		371
+#define __NR_recvmsg		372
+#define __NR_shutdown		373
+#define NR_syscalls 374
 
 /* 
  * There are some system calls that are not present on 64 bit, some

arch/s390/kernel/compat_signal.c

@@ -48,6 +48,19 @@ typedef struct
 	struct ucontext32 uc;
 } rt_sigframe32;
 
+static inline void sigset_to_sigset32(unsigned long *set64,
+				      compat_sigset_word *set32)
+{
+	set32[0] = (compat_sigset_word) set64[0];
+	set32[1] = (compat_sigset_word)(set64[0] >> 32);
+}
+
+static inline void sigset32_to_sigset(compat_sigset_word *set32,
+				      unsigned long *set64)
+{
+	set64[0] = (unsigned long) set32[0] | ((unsigned long) set32[1] << 32);
+}
+
 int copy_siginfo_to_user32(compat_siginfo_t __user *to, const siginfo_t *from)
 {
 	int err;
@@ -281,10 +294,12 @@ COMPAT_SYSCALL_DEFINE0(sigreturn)
 {
 	struct pt_regs *regs = task_pt_regs(current);
 	sigframe32 __user *frame = (sigframe32 __user *)regs->gprs[15];
+	compat_sigset_t cset;
 	sigset_t set;
 
-	if (__copy_from_user(&set.sig, &frame->sc.oldmask, _SIGMASK_COPY_SIZE32))
+	if (__copy_from_user(&cset.sig, &frame->sc.oldmask, _SIGMASK_COPY_SIZE32))
 		goto badframe;
+	sigset32_to_sigset(cset.sig, set.sig);
 	set_current_blocked(&set);
 	save_fpu_regs();
 	if (restore_sigregs32(regs, &frame->sregs))
@@ -302,10 +317,12 @@ COMPAT_SYSCALL_DEFINE0(rt_sigreturn)
 {
 	struct pt_regs *regs = task_pt_regs(current);
 	rt_sigframe32 __user *frame = (rt_sigframe32 __user *)regs->gprs[15];
+	compat_sigset_t cset;
 	sigset_t set;
 
-	if (__copy_from_user(&set, &frame->uc.uc_sigmask, sizeof(set)))
+	if (__copy_from_user(&cset, &frame->uc.uc_sigmask, sizeof(cset)))
 		goto badframe;
+	sigset32_to_sigset(cset.sig, set.sig);
 	set_current_blocked(&set);
 	if (compat_restore_altstack(&frame->uc.uc_stack))
 		goto badframe;
@@ -377,7 +394,7 @@ static int setup_frame32(struct ksignal *ksig, sigset_t *set,
 		return -EFAULT;
 
 	/* Create struct sigcontext32 on the signal stack */
-	memcpy(&sc.oldmask, &set->sig, _SIGMASK_COPY_SIZE32);
+	sigset_to_sigset32(set->sig, sc.oldmask);
 	sc.sregs = (__u32)(unsigned long __force) &frame->sregs;
 	if (__copy_to_user(&frame->sc, &sc, sizeof(frame->sc)))
 		return -EFAULT;
@@ -438,6 +455,7 @@ static int setup_frame32(struct ksignal *ksig, sigset_t *set,
 static int setup_rt_frame32(struct ksignal *ksig, sigset_t *set,
 			    struct pt_regs *regs)
 {
+	compat_sigset_t cset;
 	rt_sigframe32 __user *frame;
 	unsigned long restorer;
 	size_t frame_size;
@@ -485,11 +503,12 @@ static int setup_rt_frame32(struct ksignal *ksig, sigset_t *set,
 	store_sigregs();
 
 	/* Create ucontext on the signal stack. */
+	sigset_to_sigset32(set->sig, cset.sig);
 	if (__put_user(uc_flags, &frame->uc.uc_flags) ||
 	    __put_user(0, &frame->uc.uc_link) ||
 	    __compat_save_altstack(&frame->uc.uc_stack, regs->gprs[15]) ||
 	    save_sigregs32(regs, &frame->uc.uc_mcontext) ||
-	    __copy_to_user(&frame->uc.uc_sigmask, set, sizeof(*set)) ||
+	    __copy_to_user(&frame->uc.uc_sigmask, &cset, sizeof(cset)) ||
 	    save_sigregs_ext32(regs, &frame->uc.uc_mcontext_ext))
 		return -EFAULT;
 

arch/s390/kernel/compat_wrapper.c

@@ -52,15 +52,13 @@
  * the regular system call wrappers.
  */
 #define COMPAT_SYSCALL_WRAPx(x, name, ...)					\
-	asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__));		\
-	asmlinkage long compat_sys##name(__MAP(x,__SC_COMPAT_TYPE,__VA_ARGS__));\
-	asmlinkage long compat_sys##name(__MAP(x,__SC_COMPAT_TYPE,__VA_ARGS__))	\
-	{									\
-		return sys##name(__MAP(x,__SC_COMPAT_CAST,__VA_ARGS__));	\
-	}
+asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__));			\
+asmlinkage long notrace compat_sys##name(__MAP(x,__SC_COMPAT_TYPE,__VA_ARGS__));\
+asmlinkage long notrace compat_sys##name(__MAP(x,__SC_COMPAT_TYPE,__VA_ARGS__))	\
+{										\
+	return sys##name(__MAP(x,__SC_COMPAT_CAST,__VA_ARGS__));		\
+}
 
-COMPAT_SYSCALL_WRAP1(exit, int, error_code);
-COMPAT_SYSCALL_WRAP1(close, unsigned int, fd);
 COMPAT_SYSCALL_WRAP2(creat, const char __user *, pathname, umode_t, mode);
 COMPAT_SYSCALL_WRAP2(link, const char __user *, oldname, const char __user *, newname);
 COMPAT_SYSCALL_WRAP1(unlink, const char __user *, pathname);
@@ -68,23 +66,16 @@ COMPAT_SYSCALL_WRAP1(chdir, const char __user *, filename);
 COMPAT_SYSCALL_WRAP3(mknod, const char __user *, filename, umode_t, mode, unsigned, dev);
 COMPAT_SYSCALL_WRAP2(chmod, const char __user *, filename, umode_t, mode);
 COMPAT_SYSCALL_WRAP1(oldumount, char __user *, name);
-COMPAT_SYSCALL_WRAP1(alarm, unsigned int, seconds);
 COMPAT_SYSCALL_WRAP2(access, const char __user *, filename, int, mode);
-COMPAT_SYSCALL_WRAP1(nice, int, increment);
-COMPAT_SYSCALL_WRAP2(kill, int, pid, int, sig);
 COMPAT_SYSCALL_WRAP2(rename, const char __user *, oldname, const char __user *, newname);
 COMPAT_SYSCALL_WRAP2(mkdir, const char __user *, pathname, umode_t, mode);
 COMPAT_SYSCALL_WRAP1(rmdir, const char __user *, pathname);
-COMPAT_SYSCALL_WRAP1(dup, unsigned int, fildes);
 COMPAT_SYSCALL_WRAP1(pipe, int __user *, fildes);
 COMPAT_SYSCALL_WRAP1(brk, unsigned long, brk);
 COMPAT_SYSCALL_WRAP2(signal, int, sig, __sighandler_t, handler);
 COMPAT_SYSCALL_WRAP1(acct, const char __user *, name);
 COMPAT_SYSCALL_WRAP2(umount, char __user *, name, int, flags);
-COMPAT_SYSCALL_WRAP2(setpgid, pid_t, pid, pid_t, pgid);
-COMPAT_SYSCALL_WRAP1(umask, int, mask);
 COMPAT_SYSCALL_WRAP1(chroot, const char __user *, filename);
-COMPAT_SYSCALL_WRAP2(dup2, unsigned int, oldfd, unsigned int, newfd);
 COMPAT_SYSCALL_WRAP3(sigsuspend, int, unused1, int, unused2, old_sigset_t, mask);
 COMPAT_SYSCALL_WRAP2(sethostname, char __user *, name, int, len);
 COMPAT_SYSCALL_WRAP2(symlink, const char __user *, old, const char __user *, new);
@@ -93,37 +84,23 @@ COMPAT_SYSCALL_WRAP1(uselib, const char __user *, library);
 COMPAT_SYSCALL_WRAP2(swapon, const char __user *, specialfile, int, swap_flags);
 COMPAT_SYSCALL_WRAP4(reboot, int, magic1, int, magic2, unsigned int, cmd, void __user *, arg);
 COMPAT_SYSCALL_WRAP2(munmap, unsigned long, addr, size_t, len);
-COMPAT_SYSCALL_WRAP2(fchmod, unsigned int, fd, umode_t, mode);
-COMPAT_SYSCALL_WRAP2(getpriority, int, which, int, who);
-COMPAT_SYSCALL_WRAP3(setpriority, int, which, int, who, int, niceval);
 COMPAT_SYSCALL_WRAP3(syslog, int, type, char __user *, buf, int, len);
 COMPAT_SYSCALL_WRAP1(swapoff, const char __user *, specialfile);
-COMPAT_SYSCALL_WRAP1(fsync, unsigned int, fd);
 COMPAT_SYSCALL_WRAP2(setdomainname, char __user *, name, int, len);
 COMPAT_SYSCALL_WRAP1(newuname, struct new_utsname __user *, name);
 COMPAT_SYSCALL_WRAP3(mprotect, unsigned long, start, size_t, len, unsigned long, prot);
 COMPAT_SYSCALL_WRAP3(init_module, void __user *, umod, unsigned long, len, const char __user *, uargs);
 COMPAT_SYSCALL_WRAP2(delete_module, const char __user *, name_user, unsigned int, flags);
 COMPAT_SYSCALL_WRAP4(quotactl, unsigned int, cmd, const char __user *, special, qid_t, id, void __user *, addr);
-COMPAT_SYSCALL_WRAP1(getpgid, pid_t, pid);
-COMPAT_SYSCALL_WRAP1(fchdir, unsigned int, fd);
 COMPAT_SYSCALL_WRAP2(bdflush, int, func, long, data);
 COMPAT_SYSCALL_WRAP3(sysfs, int, option, unsigned long, arg1, unsigned long, arg2);
-COMPAT_SYSCALL_WRAP1(s390_personality, unsigned int, personality);
 COMPAT_SYSCALL_WRAP5(llseek, unsigned int, fd, unsigned long, high, unsigned long, low, loff_t __user *, result, unsigned int, whence);
-COMPAT_SYSCALL_WRAP2(flock, unsigned int, fd, unsigned int, cmd);
 COMPAT_SYSCALL_WRAP3(msync, unsigned long, start, size_t, len, int, flags);
-COMPAT_SYSCALL_WRAP1(getsid, pid_t, pid);
-COMPAT_SYSCALL_WRAP1(fdatasync, unsigned int, fd);
 COMPAT_SYSCALL_WRAP2(mlock, unsigned long, start, size_t, len);
 COMPAT_SYSCALL_WRAP2(munlock, unsigned long, start, size_t, len);
-COMPAT_SYSCALL_WRAP1(mlockall, int, flags);
 COMPAT_SYSCALL_WRAP2(sched_setparam, pid_t, pid, struct sched_param __user *, param);
 COMPAT_SYSCALL_WRAP2(sched_getparam, pid_t, pid, struct sched_param __user *, param);
 COMPAT_SYSCALL_WRAP3(sched_setscheduler, pid_t, pid, int, policy, struct sched_param __user *, param);
-COMPAT_SYSCALL_WRAP1(sched_getscheduler, pid_t, pid);
-COMPAT_SYSCALL_WRAP1(sched_get_priority_max, int, policy);
-COMPAT_SYSCALL_WRAP1(sched_get_priority_min, int, policy);
 COMPAT_SYSCALL_WRAP5(mremap, unsigned long, addr, unsigned long, old_len, unsigned long, new_len, unsigned long, flags, unsigned long, new_addr);
 COMPAT_SYSCALL_WRAP3(poll, struct pollfd __user *, ufds, unsigned int, nfds, int, timeout);
 COMPAT_SYSCALL_WRAP5(prctl, int, option, unsigned long, arg2, unsigned long, arg3, unsigned long, arg4, unsigned long, arg5);
@@ -131,20 +108,11 @@ COMPAT_SYSCALL_WRAP2(getcwd, char __user *, buf, unsigned long, size);
 COMPAT_SYSCALL_WRAP2(capget, cap_user_header_t, header, cap_user_data_t, dataptr);
 COMPAT_SYSCALL_WRAP2(capset, cap_user_header_t, header, const cap_user_data_t, data);
 COMPAT_SYSCALL_WRAP3(lchown, const char __user *, filename, uid_t, user, gid_t, group);
-COMPAT_SYSCALL_WRAP2(setreuid, uid_t, ruid, uid_t, euid);
-COMPAT_SYSCALL_WRAP2(setregid, gid_t, rgid, gid_t, egid);
 COMPAT_SYSCALL_WRAP2(getgroups, int, gidsetsize, gid_t __user *, grouplist);
 COMPAT_SYSCALL_WRAP2(setgroups, int, gidsetsize, gid_t __user *, grouplist);
-COMPAT_SYSCALL_WRAP3(fchown, unsigned int, fd, uid_t, user, gid_t, group);
-COMPAT_SYSCALL_WRAP3(setresuid, uid_t, ruid, uid_t, euid, uid_t, suid);
 COMPAT_SYSCALL_WRAP3(getresuid, uid_t __user *, ruid, uid_t __user *, euid, uid_t __user *, suid);
-COMPAT_SYSCALL_WRAP3(setresgid, gid_t, rgid, gid_t, egid, gid_t, sgid);
 COMPAT_SYSCALL_WRAP3(getresgid, gid_t __user *, rgid, gid_t __user *, egid, gid_t __user *, sgid);
 COMPAT_SYSCALL_WRAP3(chown, const char __user *, filename, uid_t, user, gid_t, group);
-COMPAT_SYSCALL_WRAP1(setuid, uid_t, uid);
-COMPAT_SYSCALL_WRAP1(setgid, gid_t, gid);
-COMPAT_SYSCALL_WRAP1(setfsuid, uid_t, uid);
-COMPAT_SYSCALL_WRAP1(setfsgid, gid_t, gid);
 COMPAT_SYSCALL_WRAP2(pivot_root, const char __user *, new_root, const char __user *, put_old);
 COMPAT_SYSCALL_WRAP3(mincore, unsigned long, start, size_t, len, unsigned char __user *, vec);
 COMPAT_SYSCALL_WRAP3(madvise, unsigned long, start, size_t, len, int, behavior);
@@ -161,23 +129,16 @@ COMPAT_SYSCALL_WRAP3(flistxattr, int, fd, char __user *, list, size_t, size);
 COMPAT_SYSCALL_WRAP2(removexattr, const char __user *, path, const char __user *, name);
 COMPAT_SYSCALL_WRAP2(lremovexattr, const char __user *, path, const char __user *, name);
 COMPAT_SYSCALL_WRAP2(fremovexattr, int, fd, const char __user *, name);
-COMPAT_SYSCALL_WRAP1(exit_group, int, error_code);
 COMPAT_SYSCALL_WRAP1(set_tid_address, int __user *, tidptr);
-COMPAT_SYSCALL_WRAP1(epoll_create, int, size);
 COMPAT_SYSCALL_WRAP4(epoll_ctl, int, epfd, int, op, int, fd, struct epoll_event __user *, event);
 COMPAT_SYSCALL_WRAP4(epoll_wait, int, epfd, struct epoll_event __user *, events, int, maxevents, int, timeout);
-COMPAT_SYSCALL_WRAP1(timer_getoverrun, timer_t, timer_id);
-COMPAT_SYSCALL_WRAP1(timer_delete, compat_timer_t, compat_timer_id);
 COMPAT_SYSCALL_WRAP1(io_destroy, aio_context_t, ctx);
 COMPAT_SYSCALL_WRAP3(io_cancel, aio_context_t, ctx_id, struct iocb __user *, iocb, struct io_event __user *, result);
 COMPAT_SYSCALL_WRAP1(mq_unlink, const char __user *, name);
 COMPAT_SYSCALL_WRAP5(add_key, const char __user *, tp, const char __user *, dsc, const void __user *, pld, size_t, len, key_serial_t, id);
 COMPAT_SYSCALL_WRAP4(request_key, const char __user *, tp, const char __user *, dsc, const char __user *, info, key_serial_t, id);
 COMPAT_SYSCALL_WRAP5(remap_file_pages, unsigned long, start, unsigned long, size, unsigned long, prot, unsigned long, pgoff, unsigned long, flags);
-COMPAT_SYSCALL_WRAP3(ioprio_set, int, which, int, who, int, ioprio);
-COMPAT_SYSCALL_WRAP2(ioprio_get, int, which, int, who);
 COMPAT_SYSCALL_WRAP3(inotify_add_watch, int, fd, const char __user *, path, u32, mask);
-COMPAT_SYSCALL_WRAP2(inotify_rm_watch, int, fd, __s32, wd);
 COMPAT_SYSCALL_WRAP3(mkdirat, int, dfd, const char __user *, pathname, umode_t, mode);
 COMPAT_SYSCALL_WRAP4(mknodat, int, dfd, const char __user *, filename, umode_t, mode, unsigned, dev);
 COMPAT_SYSCALL_WRAP5(fchownat, int, dfd, const char __user *, filename, uid_t, user, gid_t, group, int, flag);
@@ -192,23 +153,11 @@ COMPAT_SYSCALL_WRAP1(unshare, unsigned long, unshare_flags);
 COMPAT_SYSCALL_WRAP6(splice, int, fd_in, loff_t __user *, off_in, int, fd_out, loff_t __user *, off_out, size_t, len, unsigned int, flags);
 COMPAT_SYSCALL_WRAP4(tee, int, fdin, int, fdout, size_t, len, unsigned int, flags);
 COMPAT_SYSCALL_WRAP3(getcpu, unsigned __user *, cpu, unsigned __user *, node, struct getcpu_cache __user *, cache);
-COMPAT_SYSCALL_WRAP1(eventfd, unsigned int, count);
-COMPAT_SYSCALL_WRAP2(timerfd_create, int, clockid, int, flags);
-COMPAT_SYSCALL_WRAP2(eventfd2, unsigned int, count, int, flags);
-COMPAT_SYSCALL_WRAP1(inotify_init1, int, flags);
 COMPAT_SYSCALL_WRAP2(pipe2, int __user *, fildes, int, flags);
-COMPAT_SYSCALL_WRAP3(dup3, unsigned int, oldfd, unsigned int, newfd, int, flags);
-COMPAT_SYSCALL_WRAP1(epoll_create1, int, flags);
-COMPAT_SYSCALL_WRAP2(tkill, int, pid, int, sig);
-COMPAT_SYSCALL_WRAP3(tgkill, int, tgid, int, pid, int, sig);
 COMPAT_SYSCALL_WRAP5(perf_event_open, struct perf_event_attr __user *, attr_uptr, pid_t, pid, int, cpu, int, group_fd, unsigned long, flags);
 COMPAT_SYSCALL_WRAP5(clone, unsigned long, newsp, unsigned long, clone_flags, int __user *, parent_tidptr, int __user *, child_tidptr, unsigned long, tls);
-COMPAT_SYSCALL_WRAP2(fanotify_init, unsigned int, flags, unsigned int, event_f_flags);
 COMPAT_SYSCALL_WRAP4(prlimit64, pid_t, pid, unsigned int, resource, const struct rlimit64 __user *, new_rlim, struct rlimit64 __user *, old_rlim);
 COMPAT_SYSCALL_WRAP5(name_to_handle_at, int, dfd, const char __user *, name, struct file_handle __user *, handle, int __user *, mnt_id, int, flag);
-COMPAT_SYSCALL_WRAP1(syncfs, int, fd);
-COMPAT_SYSCALL_WRAP2(setns, int, fd, int, nstype);
-COMPAT_SYSCALL_WRAP2(s390_runtime_instr, int, command, int, signum);
 COMPAT_SYSCALL_WRAP5(kcmp, pid_t, pid1, pid_t, pid2, int, type, unsigned long, idx1, unsigned long, idx2);
 COMPAT_SYSCALL_WRAP3(finit_module, int, fd, const char __user *, uargs, int, flags);
 COMPAT_SYSCALL_WRAP3(sched_setattr, pid_t, pid, struct sched_attr __user *, attr, unsigned int, flags);
@@ -220,3 +169,10 @@ COMPAT_SYSCALL_WRAP2(memfd_create, const char __user *, uname, unsigned int, fla
 COMPAT_SYSCALL_WRAP3(bpf, int, cmd, union bpf_attr *, attr, unsigned int, size);
 COMPAT_SYSCALL_WRAP3(s390_pci_mmio_write, const unsigned long, mmio_addr, const void __user *, user_buffer, const size_t, length);
 COMPAT_SYSCALL_WRAP3(s390_pci_mmio_read, const unsigned long, mmio_addr, void __user *, user_buffer, const size_t, length);
+COMPAT_SYSCALL_WRAP4(socketpair, int, family, int, type, int, protocol, int __user *, usockvec);
+COMPAT_SYSCALL_WRAP3(bind, int, fd, struct sockaddr __user *, umyaddr, int, addrlen);
+COMPAT_SYSCALL_WRAP3(connect, int, fd, struct sockaddr __user *, uservaddr, int, addrlen);
+COMPAT_SYSCALL_WRAP4(accept4, int, fd, struct sockaddr __user *, upeer_sockaddr, int __user *, upeer_addrlen, int, flags);
+COMPAT_SYSCALL_WRAP3(getsockname, int, fd, struct sockaddr __user *, usockaddr, int __user *, usockaddr_len);
+COMPAT_SYSCALL_WRAP3(getpeername, int, fd, struct sockaddr __user *, usockaddr, int __user *, usockaddr_len);
+COMPAT_SYSCALL_WRAP6(sendto, int, fd, void __user *, buff, size_t, len, unsigned int, flags, struct sockaddr __user *, addr, int, addr_len);

arch/s390/kernel/entry.S

@@ -1191,6 +1191,7 @@ cleanup_critical:
 	clg	%r9,BASED(.Lcleanup_save_fpu_fpc_end)
 	jhe	1f
 	lg	%r2,__LC_CURRENT
+	aghi	%r2,__TASK_thread
 0:	# Store floating-point controls
 	stfpc	__THREAD_FPU_fpc(%r2)
 1:	# Load register save area and check if VX is active
@@ -1252,6 +1253,7 @@ cleanup_critical:
 	clg	%r9,BASED(.Lcleanup_load_fpu_regs_vx_ctl)
 	jhe	6f
 	lg	%r4,__LC_CURRENT
+	aghi	%r4,__TASK_thread
 	lfpc	__THREAD_FPU_fpc(%r4)
 	tm	__THREAD_FPU_flags+3(%r4),FPU_USE_VX	# VX-enabled task ?
 	lg	%r4,__THREAD_FPU_regs(%r4)	# %r4 <- reg save area

arch/s390/kernel/perf_cpum_cf.c

@@ -157,10 +157,14 @@ static int validate_ctr_auth(const struct hw_perf_event *hwc)
 
 	cpuhw = &get_cpu_var(cpu_hw_events);
 
-	/* check authorization for cpu counter sets */
+	/* Check authorization for cpu counter sets.
+	 * If the particular CPU counter set is not authorized,
+	 * return with -ENOENT in order to fall back to other
+	 * PMUs that might suffice the event request.
+	 */
 	ctrs_state = cpumf_state_ctl[hwc->config_base];
 	if (!(ctrs_state & cpuhw->info.auth_ctl))
-		err = -EPERM;
+		err = -ENOENT;
 
 	put_cpu_var(cpu_hw_events);
 	return err;
@@ -536,7 +540,7 @@ static int cpumf_pmu_add(struct perf_event *event, int flags)
 	 */
 	if (!(cpuhw->flags & PERF_EVENT_TXN))
 		if (validate_ctr_auth(&event->hw))
-			return -EPERM;
+			return -ENOENT;
 
 	ctr_set_enable(&cpuhw->state, event->hw.config_base);
 	event->hw.state = PERF_HES_UPTODATE | PERF_HES_STOPPED;
@@ -611,7 +615,7 @@ static int cpumf_pmu_commit_txn(struct pmu *pmu)
 	state = cpuhw->state & ~((1 << CPUMF_LCCTL_ENABLE_SHIFT) - 1);
 	state >>= CPUMF_LCCTL_ENABLE_SHIFT;
 	if ((state & cpuhw->info.auth_ctl) != state)
-		return -EPERM;
+		return -ENOENT;
 
 	cpuhw->flags &= ~PERF_EVENT_TXN;
 	perf_pmu_enable(pmu);

arch/s390/kernel/swsusp.S

@@ -30,6 +30,9 @@ ENTRY(swsusp_arch_suspend)
 	aghi	%r15,-STACK_FRAME_OVERHEAD
 	stg	%r1,__SF_BACKCHAIN(%r15)
 
+	/* Store FPU registers */
+	brasl	%r14,save_fpu_regs
+
 	/* Deactivate DAT */
 	stnsm	__SF_EMPTY(%r15),0xfb
 
@@ -47,23 +50,6 @@ ENTRY(swsusp_arch_suspend)
 
 	/* Store registers */
 	mvc	0x318(4,%r1),__SF_EMPTY(%r15)	/* move prefix to lowcore */
-	stfpc	0x31c(%r1)			/* store fpu control */
-	std	0,0x200(%r1)			/* store f0 */
-	std	1,0x208(%r1)			/* store f1 */
-	std	2,0x210(%r1)			/* store f2 */
-	std	3,0x218(%r1)			/* store f3 */
-	std	4,0x220(%r1)			/* store f4 */
-	std	5,0x228(%r1)			/* store f5 */
-	std	6,0x230(%r1)			/* store f6 */
-	std	7,0x238(%r1)			/* store f7 */
-	std	8,0x240(%r1)			/* store f8 */
-	std	9,0x248(%r1)			/* store f9 */
-	std	10,0x250(%r1)			/* store f10 */
-	std	11,0x258(%r1)			/* store f11 */
-	std	12,0x260(%r1)			/* store f12 */
-	std	13,0x268(%r1)			/* store f13 */
-	std	14,0x270(%r1)			/* store f14 */
-	std	15,0x278(%r1)			/* store f15 */
 	stam	%a0,%a15,0x340(%r1)		/* store access registers */
 	stctg	%c0,%c15,0x380(%r1)		/* store control registers */
 	stmg	%r0,%r15,0x280(%r1)		/* store general registers */
@@ -249,24 +235,6 @@ restore_registers:
 	lctlg	%c0,%c15,0x380(%r13)	/* load control registers */
 	lam	%a0,%a15,0x340(%r13)	/* load access registers */
 
-	lfpc	0x31c(%r13)		/* load fpu control */
-	ld	0,0x200(%r13)		/* load f0 */
-	ld	1,0x208(%r13)		/* load f1 */
-	ld	2,0x210(%r13)		/* load f2 */
-	ld	3,0x218(%r13)		/* load f3 */
-	ld	4,0x220(%r13)		/* load f4 */
-	ld	5,0x228(%r13)		/* load f5 */
-	ld	6,0x230(%r13)		/* load f6 */
-	ld	7,0x238(%r13)		/* load f7 */
-	ld	8,0x240(%r13)		/* load f8 */
-	ld	9,0x248(%r13)		/* load f9 */
-	ld	10,0x250(%r13)		/* load f10 */
-	ld	11,0x258(%r13)		/* load f11 */
-	ld	12,0x260(%r13)		/* load f12 */
-	ld	13,0x268(%r13)		/* load f13 */
-	ld	14,0x270(%r13)		/* load f14 */
-	ld	15,0x278(%r13)		/* load f15 */
-
 	/* Load old stack */
 	lg	%r15,0x2f8(%r13)
 

arch/s390/kernel/syscalls.S

@@ -9,12 +9,12 @@
 #define NI_SYSCALL SYSCALL(sys_ni_syscall,sys_ni_syscall)
 
 NI_SYSCALL						/* 0 */
-SYSCALL(sys_exit,compat_sys_exit)
+SYSCALL(sys_exit,sys_exit)
 SYSCALL(sys_fork,sys_fork)
 SYSCALL(sys_read,compat_sys_s390_read)
 SYSCALL(sys_write,compat_sys_s390_write)
 SYSCALL(sys_open,compat_sys_open)			/* 5 */
-SYSCALL(sys_close,compat_sys_close)
+SYSCALL(sys_close,sys_close)
 SYSCALL(sys_restart_syscall,sys_restart_syscall)
 SYSCALL(sys_creat,compat_sys_creat)
 SYSCALL(sys_link,compat_sys_link)
@@ -35,21 +35,21 @@ SYSCALL(sys_ni_syscall,compat_sys_s390_setuid16)	/* old setuid16 syscall*/
 SYSCALL(sys_ni_syscall,compat_sys_s390_getuid16)	/* old getuid16 syscall*/
 SYSCALL(sys_ni_syscall,compat_sys_stime)		/* 25 old stime syscall */
 SYSCALL(sys_ptrace,compat_sys_ptrace)
-SYSCALL(sys_alarm,compat_sys_alarm)
+SYSCALL(sys_alarm,sys_alarm)
 NI_SYSCALL						/* old fstat syscall */
 SYSCALL(sys_pause,sys_pause)
 SYSCALL(sys_utime,compat_sys_utime)			/* 30 */
 NI_SYSCALL						/* old stty syscall */
 NI_SYSCALL						/* old gtty syscall */
 SYSCALL(sys_access,compat_sys_access)
-SYSCALL(sys_nice,compat_sys_nice)
+SYSCALL(sys_nice,sys_nice)
 NI_SYSCALL						/* 35 old ftime syscall */
 SYSCALL(sys_sync,sys_sync)
-SYSCALL(sys_kill,compat_sys_kill)
+SYSCALL(sys_kill,sys_kill)
 SYSCALL(sys_rename,compat_sys_rename)
 SYSCALL(sys_mkdir,compat_sys_mkdir)
 SYSCALL(sys_rmdir,compat_sys_rmdir)			/* 40 */
-SYSCALL(sys_dup,compat_sys_dup)
+SYSCALL(sys_dup,sys_dup)
 SYSCALL(sys_pipe,compat_sys_pipe)
 SYSCALL(sys_times,compat_sys_times)
 NI_SYSCALL						/* old prof syscall */
@@ -65,13 +65,13 @@ NI_SYSCALL						/* old lock syscall */
 SYSCALL(sys_ioctl,compat_sys_ioctl)
 SYSCALL(sys_fcntl,compat_sys_fcntl)			/* 55 */
 NI_SYSCALL						/* intel mpx syscall */
-SYSCALL(sys_setpgid,compat_sys_setpgid)
+SYSCALL(sys_setpgid,sys_setpgid)
 NI_SYSCALL						/* old ulimit syscall */
 NI_SYSCALL						/* old uname syscall */
-SYSCALL(sys_umask,compat_sys_umask)			/* 60 */
+SYSCALL(sys_umask,sys_umask)				/* 60 */
 SYSCALL(sys_chroot,compat_sys_chroot)
 SYSCALL(sys_ustat,compat_sys_ustat)
-SYSCALL(sys_dup2,compat_sys_dup2)
+SYSCALL(sys_dup2,sys_dup2)
 SYSCALL(sys_getppid,sys_getppid)
 SYSCALL(sys_getpgrp,sys_getpgrp)			/* 65 */
 SYSCALL(sys_setsid,sys_setsid)
@@ -102,10 +102,10 @@ SYSCALL(sys_old_mmap,compat_sys_s390_old_mmap)		/* 90 */
 SYSCALL(sys_munmap,compat_sys_munmap)
 SYSCALL(sys_truncate,compat_sys_truncate)
 SYSCALL(sys_ftruncate,compat_sys_ftruncate)
-SYSCALL(sys_fchmod,compat_sys_fchmod)
+SYSCALL(sys_fchmod,sys_fchmod)
 SYSCALL(sys_ni_syscall,compat_sys_s390_fchown16)	/* 95 old fchown16 syscall*/
-SYSCALL(sys_getpriority,compat_sys_getpriority)
-SYSCALL(sys_setpriority,compat_sys_setpriority)
+SYSCALL(sys_getpriority,sys_getpriority)
+SYSCALL(sys_setpriority,sys_setpriority)
 NI_SYSCALL						/* old profil syscall */
 SYSCALL(sys_statfs,compat_sys_statfs)
 SYSCALL(sys_fstatfs,compat_sys_fstatfs)			/* 100 */
@@ -126,7 +126,7 @@ SYSCALL(sys_wait4,compat_sys_wait4)
 SYSCALL(sys_swapoff,compat_sys_swapoff)			/* 115 */
 SYSCALL(sys_sysinfo,compat_sys_sysinfo)
 SYSCALL(sys_s390_ipc,compat_sys_s390_ipc)
-SYSCALL(sys_fsync,compat_sys_fsync)
+SYSCALL(sys_fsync,sys_fsync)
 SYSCALL(sys_sigreturn,compat_sys_sigreturn)
 SYSCALL(sys_clone,compat_sys_clone)			/* 120 */
 SYSCALL(sys_setdomainname,compat_sys_setdomainname)
@@ -140,35 +140,35 @@ SYSCALL(sys_init_module,compat_sys_init_module)
 SYSCALL(sys_delete_module,compat_sys_delete_module)
 NI_SYSCALL						/* 130: old get_kernel_syms */
 SYSCALL(sys_quotactl,compat_sys_quotactl)
-SYSCALL(sys_getpgid,compat_sys_getpgid)
-SYSCALL(sys_fchdir,compat_sys_fchdir)
+SYSCALL(sys_getpgid,sys_getpgid)
+SYSCALL(sys_fchdir,sys_fchdir)
 SYSCALL(sys_bdflush,compat_sys_bdflush)
 SYSCALL(sys_sysfs,compat_sys_sysfs)			/* 135 */
-SYSCALL(sys_s390_personality,compat_sys_s390_personality)
+SYSCALL(sys_s390_personality,sys_s390_personality)
 NI_SYSCALL						/* for afs_syscall */
 SYSCALL(sys_ni_syscall,compat_sys_s390_setfsuid16)	/* old setfsuid16 syscall */
 SYSCALL(sys_ni_syscall,compat_sys_s390_setfsgid16)	/* old setfsgid16 syscall */
 SYSCALL(sys_llseek,compat_sys_llseek)			/* 140 */
 SYSCALL(sys_getdents,compat_sys_getdents)
 SYSCALL(sys_select,compat_sys_select)
-SYSCALL(sys_flock,compat_sys_flock)
+SYSCALL(sys_flock,sys_flock)
 SYSCALL(sys_msync,compat_sys_msync)
 SYSCALL(sys_readv,compat_sys_readv)			/* 145 */
 SYSCALL(sys_writev,compat_sys_writev)
-SYSCALL(sys_getsid,compat_sys_getsid)
-SYSCALL(sys_fdatasync,compat_sys_fdatasync)
+SYSCALL(sys_getsid,sys_getsid)
+SYSCALL(sys_fdatasync,sys_fdatasync)
 SYSCALL(sys_sysctl,compat_sys_sysctl)
 SYSCALL(sys_mlock,compat_sys_mlock)			/* 150 */
 SYSCALL(sys_munlock,compat_sys_munlock)
-SYSCALL(sys_mlockall,compat_sys_mlockall)
+SYSCALL(sys_mlockall,sys_mlockall)
 SYSCALL(sys_munlockall,sys_munlockall)
 SYSCALL(sys_sched_setparam,compat_sys_sched_setparam)
 SYSCALL(sys_sched_getparam,compat_sys_sched_getparam)	/* 155 */
 SYSCALL(sys_sched_setscheduler,compat_sys_sched_setscheduler)
-SYSCALL(sys_sched_getscheduler,compat_sys_sched_getscheduler)
+SYSCALL(sys_sched_getscheduler,sys_sched_getscheduler)
 SYSCALL(sys_sched_yield,sys_sched_yield)
-SYSCALL(sys_sched_get_priority_max,compat_sys_sched_get_priority_max)
-SYSCALL(sys_sched_get_priority_min,compat_sys_sched_get_priority_min)	/* 160 */
+SYSCALL(sys_sched_get_priority_max,sys_sched_get_priority_max)
+SYSCALL(sys_sched_get_priority_min,sys_sched_get_priority_min)	/* 160 */
 SYSCALL(sys_sched_rr_get_interval,compat_sys_sched_rr_get_interval)
 SYSCALL(sys_nanosleep,compat_sys_nanosleep)
 SYSCALL(sys_mremap,compat_sys_mremap)
@@ -211,20 +211,20 @@ SYSCALL(sys_getuid,sys_getuid)
 SYSCALL(sys_getgid,sys_getgid)				/* 200 */
 SYSCALL(sys_geteuid,sys_geteuid)
 SYSCALL(sys_getegid,sys_getegid)
-SYSCALL(sys_setreuid,compat_sys_setreuid)
-SYSCALL(sys_setregid,compat_sys_setregid)
+SYSCALL(sys_setreuid,sys_setreuid)
+SYSCALL(sys_setregid,sys_setregid)
 SYSCALL(sys_getgroups,compat_sys_getgroups)		/* 205 */
 SYSCALL(sys_setgroups,compat_sys_setgroups)
-SYSCALL(sys_fchown,compat_sys_fchown)
-SYSCALL(sys_setresuid,compat_sys_setresuid)
+SYSCALL(sys_fchown,sys_fchown)
+SYSCALL(sys_setresuid,sys_setresuid)
 SYSCALL(sys_getresuid,compat_sys_getresuid)
-SYSCALL(sys_setresgid,compat_sys_setresgid)		/* 210 */
+SYSCALL(sys_setresgid,sys_setresgid)			/* 210 */
 SYSCALL(sys_getresgid,compat_sys_getresgid)
 SYSCALL(sys_chown,compat_sys_chown)
-SYSCALL(sys_setuid,compat_sys_setuid)
-SYSCALL(sys_setgid,compat_sys_setgid)
-SYSCALL(sys_setfsuid,compat_sys_setfsuid)		/* 215 */
-SYSCALL(sys_setfsgid,compat_sys_setfsgid)
+SYSCALL(sys_setuid,sys_setuid)
+SYSCALL(sys_setgid,sys_setgid)
+SYSCALL(sys_setfsuid,sys_setfsuid)			/* 215 */
+SYSCALL(sys_setfsgid,sys_setfsgid)
 SYSCALL(sys_pivot_root,compat_sys_pivot_root)
 SYSCALL(sys_mincore,compat_sys_mincore)
 SYSCALL(sys_madvise,compat_sys_madvise)
@@ -245,19 +245,19 @@ SYSCALL(sys_removexattr,compat_sys_removexattr)
 SYSCALL(sys_lremovexattr,compat_sys_lremovexattr)
 SYSCALL(sys_fremovexattr,compat_sys_fremovexattr)	/* 235 */
 SYSCALL(sys_gettid,sys_gettid)
-SYSCALL(sys_tkill,compat_sys_tkill)
+SYSCALL(sys_tkill,sys_tkill)
 SYSCALL(sys_futex,compat_sys_futex)
 SYSCALL(sys_sched_setaffinity,compat_sys_sched_setaffinity)
 SYSCALL(sys_sched_getaffinity,compat_sys_sched_getaffinity)	/* 240 */
-SYSCALL(sys_tgkill,compat_sys_tgkill)
+SYSCALL(sys_tgkill,sys_tgkill)
 NI_SYSCALL						/* reserved for TUX */
 SYSCALL(sys_io_setup,compat_sys_io_setup)
 SYSCALL(sys_io_destroy,compat_sys_io_destroy)
 SYSCALL(sys_io_getevents,compat_sys_io_getevents)	/* 245 */
 SYSCALL(sys_io_submit,compat_sys_io_submit)
 SYSCALL(sys_io_cancel,compat_sys_io_cancel)
-SYSCALL(sys_exit_group,compat_sys_exit_group)
-SYSCALL(sys_epoll_create,compat_sys_epoll_create)
+SYSCALL(sys_exit_group,sys_exit_group)
+SYSCALL(sys_epoll_create,sys_epoll_create)
 SYSCALL(sys_epoll_ctl,compat_sys_epoll_ctl)		/* 250 */
 SYSCALL(sys_epoll_wait,compat_sys_epoll_wait)
 SYSCALL(sys_set_tid_address,compat_sys_set_tid_address)
@@ -265,8 +265,8 @@ SYSCALL(sys_fadvise64_64,compat_sys_s390_fadvise64)
 SYSCALL(sys_timer_create,compat_sys_timer_create)
 SYSCALL(sys_timer_settime,compat_sys_timer_settime)	/* 255 */
 SYSCALL(sys_timer_gettime,compat_sys_timer_gettime)
-SYSCALL(sys_timer_getoverrun,compat_sys_timer_getoverrun)
-SYSCALL(sys_timer_delete,compat_sys_timer_delete)
+SYSCALL(sys_timer_getoverrun,sys_timer_getoverrun)
+SYSCALL(sys_timer_delete,sys_timer_delete)
 SYSCALL(sys_clock_settime,compat_sys_clock_settime)
 SYSCALL(sys_clock_gettime,compat_sys_clock_gettime)	/* 260 */
 SYSCALL(sys_clock_getres,compat_sys_clock_getres)
@@ -290,11 +290,11 @@ SYSCALL(sys_add_key,compat_sys_add_key)
 SYSCALL(sys_request_key,compat_sys_request_key)
 SYSCALL(sys_keyctl,compat_sys_keyctl)			/* 280 */
 SYSCALL(sys_waitid,compat_sys_waitid)
-SYSCALL(sys_ioprio_set,compat_sys_ioprio_set)
-SYSCALL(sys_ioprio_get,compat_sys_ioprio_get)
+SYSCALL(sys_ioprio_set,sys_ioprio_set)
+SYSCALL(sys_ioprio_get,sys_ioprio_get)
 SYSCALL(sys_inotify_init,sys_inotify_init)
 SYSCALL(sys_inotify_add_watch,compat_sys_inotify_add_watch)	/* 285 */
-SYSCALL(sys_inotify_rm_watch,compat_sys_inotify_rm_watch)
+SYSCALL(sys_inotify_rm_watch,sys_inotify_rm_watch)
 SYSCALL(sys_migrate_pages,compat_sys_migrate_pages)
 SYSCALL(sys_openat,compat_sys_openat)
 SYSCALL(sys_mkdirat,compat_sys_mkdirat)
@@ -326,31 +326,31 @@ SYSCALL(sys_fallocate,compat_sys_s390_fallocate)
 SYSCALL(sys_utimensat,compat_sys_utimensat)		/* 315 */
 SYSCALL(sys_signalfd,compat_sys_signalfd)
 NI_SYSCALL						/* 317 old sys_timer_fd */
-SYSCALL(sys_eventfd,compat_sys_eventfd)
-SYSCALL(sys_timerfd_create,compat_sys_timerfd_create)
+SYSCALL(sys_eventfd,sys_eventfd)
+SYSCALL(sys_timerfd_create,sys_timerfd_create)
 SYSCALL(sys_timerfd_settime,compat_sys_timerfd_settime) /* 320 */
 SYSCALL(sys_timerfd_gettime,compat_sys_timerfd_gettime)
 SYSCALL(sys_signalfd4,compat_sys_signalfd4)
-SYSCALL(sys_eventfd2,compat_sys_eventfd2)
-SYSCALL(sys_inotify_init1,compat_sys_inotify_init1)
+SYSCALL(sys_eventfd2,sys_eventfd2)
+SYSCALL(sys_inotify_init1,sys_inotify_init1)
 SYSCALL(sys_pipe2,compat_sys_pipe2)			/* 325 */
-SYSCALL(sys_dup3,compat_sys_dup3)
-SYSCALL(sys_epoll_create1,compat_sys_epoll_create1)
+SYSCALL(sys_dup3,sys_dup3)
+SYSCALL(sys_epoll_create1,sys_epoll_create1)
 SYSCALL(sys_preadv,compat_sys_preadv)
 SYSCALL(sys_pwritev,compat_sys_pwritev)
 SYSCALL(sys_rt_tgsigqueueinfo,compat_sys_rt_tgsigqueueinfo) /* 330 */
 SYSCALL(sys_perf_event_open,compat_sys_perf_event_open)
-SYSCALL(sys_fanotify_init,compat_sys_fanotify_init)
+SYSCALL(sys_fanotify_init,sys_fanotify_init)
 SYSCALL(sys_fanotify_mark,compat_sys_fanotify_mark)
 SYSCALL(sys_prlimit64,compat_sys_prlimit64)
 SYSCALL(sys_name_to_handle_at,compat_sys_name_to_handle_at) /* 335 */
 SYSCALL(sys_open_by_handle_at,compat_sys_open_by_handle_at)
 SYSCALL(sys_clock_adjtime,compat_sys_clock_adjtime)
-SYSCALL(sys_syncfs,compat_sys_syncfs)
-SYSCALL(sys_setns,compat_sys_setns)
+SYSCALL(sys_syncfs,sys_syncfs)
+SYSCALL(sys_setns,sys_setns)
 SYSCALL(sys_process_vm_readv,compat_sys_process_vm_readv) /* 340 */
 SYSCALL(sys_process_vm_writev,compat_sys_process_vm_writev)
-SYSCALL(sys_s390_runtime_instr,compat_sys_s390_runtime_instr)
+SYSCALL(sys_s390_runtime_instr,sys_s390_runtime_instr)
 SYSCALL(sys_kcmp,compat_sys_kcmp)
 SYSCALL(sys_finit_module,compat_sys_finit_module)
 SYSCALL(sys_sched_setattr,compat_sys_sched_setattr)	/* 345 */
@@ -363,3 +363,22 @@ SYSCALL(sys_bpf,compat_sys_bpf)
 SYSCALL(sys_s390_pci_mmio_write,compat_sys_s390_pci_mmio_write)
 SYSCALL(sys_s390_pci_mmio_read,compat_sys_s390_pci_mmio_read)
 SYSCALL(sys_execveat,compat_sys_execveat)
+SYSCALL(sys_userfaultfd,sys_userfaultfd)		/* 355 */
+SYSCALL(sys_membarrier,sys_membarrier)
+SYSCALL(sys_recvmmsg,compat_sys_recvmmsg)
+SYSCALL(sys_sendmmsg,compat_sys_sendmmsg)
+SYSCALL(sys_socket,sys_socket)
+SYSCALL(sys_socketpair,compat_sys_socketpair)		/* 360 */
+SYSCALL(sys_bind,sys_bind)
+SYSCALL(sys_connect,sys_connect)
+SYSCALL(sys_listen,sys_listen)
+SYSCALL(sys_accept4,sys_accept4)
+SYSCALL(sys_getsockopt,compat_sys_getsockopt)		/* 365 */
+SYSCALL(sys_setsockopt,compat_sys_setsockopt)
+SYSCALL(sys_getsockname,compat_sys_getsockname)
+SYSCALL(sys_getpeername,compat_sys_getpeername)
+SYSCALL(sys_sendto,compat_sys_sendto)
+SYSCALL(sys_sendmsg,compat_sys_sendmsg)			/* 370 */
+SYSCALL(sys_recvfrom,compat_sys_recvfrom)
+SYSCALL(sys_recvmsg,compat_sys_recvmsg)
+SYSCALL(sys_shutdown,sys_shutdown)

arch/s390/kernel/vtime.c

@@ -89,17 +89,21 @@ static int do_account_vtime(struct task_struct *tsk, int hardirq_offset)
 	if (smp_cpu_mtid &&
 	    time_after64(jiffies_64, __this_cpu_read(mt_scaling_jiffies))) {
 		u64 cycles_new[32], *cycles_old;
-		u64 delta, mult, div;
+		u64 delta, fac, mult, div;
 
 		cycles_old = this_cpu_ptr(mt_cycles);
 		if (stcctm5(smp_cpu_mtid + 1, cycles_new) < 2) {
+			fac = 1;
 			mult = div = 0;
 			for (i = 0; i <= smp_cpu_mtid; i++) {
 				delta = cycles_new[i] - cycles_old[i];
-				mult += delta;
-				div += (i + 1) * delta;
+				div += delta;
+				mult *= i + 1;
+				mult += delta * fac;
+				fac *= i + 1;
 			}
-			if (mult > 0) {
+			div *= fac;
+			if (div > 0) {
 				/* Update scaling factor */
 				__this_cpu_write(mt_scaling_mult, mult);
 				__this_cpu_write(mt_scaling_div, div);

arch/x86/entry/entry_64.S

@@ -1128,7 +1128,18 @@ END(error_exit)
 
 /* Runs on exception stack */
 ENTRY(nmi)
+	/*
+	 * Fix up the exception frame if we're on Xen.
+	 * PARAVIRT_ADJUST_EXCEPTION_FRAME is guaranteed to push at most
+	 * one value to the stack on native, so it may clobber the rdx
+	 * scratch slot, but it won't clobber any of the important
+	 * slots past it.
+	 *
+	 * Xen is a different story, because the Xen frame itself overlaps
+	 * the "NMI executing" variable.
+	 */
 	PARAVIRT_ADJUST_EXCEPTION_FRAME
+
 	/*
 	 * We allow breakpoints in NMIs. If a breakpoint occurs, then
 	 * the iretq it performs will take us out of NMI context.
@@ -1179,9 +1190,12 @@ ENTRY(nmi)
 	 * we don't want to enable interrupts, because then we'll end
 	 * up in an awkward situation in which IRQs are on but NMIs
 	 * are off.
+	 *
+	 * We also must not push anything to the stack before switching
+	 * stacks lest we corrupt the "NMI executing" variable.
 	 */
 
-	SWAPGS
+	SWAPGS_UNSAFE_STACK
 	cld
 	movq	%rsp, %rdx
 	movq	PER_CPU_VAR(cpu_current_top_of_stack), %rsp

arch/x86/include/asm/efi.h

@@ -86,6 +86,16 @@ extern u64 asmlinkage efi_call(void *fp, ...);
 extern void __iomem *__init efi_ioremap(unsigned long addr, unsigned long size,
 					u32 type, u64 attribute);
 
+/*
+ * CONFIG_KASAN may redefine memset to __memset.  __memset function is present
+ * only in kernel binary.  Since the EFI stub linked into a separate binary it
+ * doesn't have __memset().  So we should use standard memset from
+ * arch/x86/boot/compressed/string.c.  The same applies to memcpy and memmove.
+ */
+#undef memcpy
+#undef memset
+#undef memmove
+
 #endif /* CONFIG_X86_32 */
 
 extern struct efi_scratch efi_scratch;

arch/x86/include/asm/kvm_host.h

@@ -40,6 +40,7 @@
 
 #define KVM_PIO_PAGE_OFFSET 1
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 2
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #define KVM_IRQCHIP_NUM_PINS  KVM_IOAPIC_NUM_PINS
 

arch/x86/include/asm/msr-index.h

@@ -331,6 +331,7 @@
 /* C1E active bits in int pending message */
 #define K8_INTP_C1E_ACTIVE_MASK		0x18000000
 #define MSR_K8_TSEG_ADDR		0xc0010112
+#define MSR_K8_TSEG_MASK		0xc0010113
 #define K8_MTRRFIXRANGE_DRAM_ENABLE	0x00040000 /* MtrrFixDramEn bit    */
 #define K8_MTRRFIXRANGE_DRAM_MODIFY	0x00080000 /* MtrrFixDramModEn bit */
 #define K8_MTRR_RDMEM_WRMEM_MASK	0x18181818 /* Mask: RdMem|WrMem    */

arch/x86/kernel/paravirt.c

@@ -41,10 +41,18 @@
 #include <asm/timer.h>
 #include <asm/special_insns.h>
 
-/* nop stub */
-void _paravirt_nop(void)
-{
-}
+/*
+ * nop stub, which must not clobber anything *including the stack* to
+ * avoid confusing the entry prologues.
+ */
+extern void _paravirt_nop(void);
+asm (".pushsection .entry.text, \"ax\"\n"
+     ".global _paravirt_nop\n"
+     "_paravirt_nop:\n\t"
+     "ret\n\t"
+     ".size _paravirt_nop, . - _paravirt_nop\n\t"
+     ".type _paravirt_nop, @function\n\t"
+     ".popsection");
 
 /* identity function, which can be inlined */
 u32 _paravirt_ident_32(u32 x)

arch/x86/kvm/mmu.c

@@ -3322,7 +3322,7 @@ walk_shadow_page_get_mmio_spte(struct kvm_vcpu *vcpu, u64 addr, u64 *sptep)
 			break;
 
 		reserved |= is_shadow_zero_bits_set(&vcpu->arch.mmu, spte,
-						    leaf);
+						    iterator.level);
 	}
 
 	walk_shadow_page_lockless_end(vcpu);
@@ -3614,7 +3614,7 @@ static void
 __reset_rsvds_bits_mask(struct kvm_vcpu *vcpu,
 			struct rsvd_bits_validate *rsvd_check,
 			int maxphyaddr, int level, bool nx, bool gbpages,
-			bool pse)
+			bool pse, bool amd)
 {
 	u64 exb_bit_rsvd = 0;
 	u64 gbpages_bit_rsvd = 0;
@@ -3631,7 +3631,7 @@ __reset_rsvds_bits_mask(struct kvm_vcpu *vcpu,
 	 * Non-leaf PML4Es and PDPEs reserve bit 8 (which would be the G bit for
 	 * leaf entries) on AMD CPUs only.
 	 */
-	if (guest_cpuid_is_amd(vcpu))
+	if (amd)
 		nonleaf_bit8_rsvd = rsvd_bits(8, 8);
 
 	switch (level) {
@@ -3699,7 +3699,7 @@ static void reset_rsvds_bits_mask(struct kvm_vcpu *vcpu,
 	__reset_rsvds_bits_mask(vcpu, &context->guest_rsvd_check,
 				cpuid_maxphyaddr(vcpu), context->root_level,
 				context->nx, guest_cpuid_has_gbpages(vcpu),
-				is_pse(vcpu));
+				is_pse(vcpu), guest_cpuid_is_amd(vcpu));
 }
 
 static void
@@ -3749,13 +3749,24 @@ static void reset_rsvds_bits_mask_ept(struct kvm_vcpu *vcpu,
 void
 reset_shadow_zero_bits_mask(struct kvm_vcpu *vcpu, struct kvm_mmu *context)
 {
+	/*
+	 * Passing "true" to the last argument is okay; it adds a check
+	 * on bit 8 of the SPTEs which KVM doesn't use anyway.
+	 */
 	__reset_rsvds_bits_mask(vcpu, &context->shadow_zero_check,
 				boot_cpu_data.x86_phys_bits,
 				context->shadow_root_level, context->nx,
-				guest_cpuid_has_gbpages(vcpu), is_pse(vcpu));
+				guest_cpuid_has_gbpages(vcpu), is_pse(vcpu),
+				true);
 }
 EXPORT_SYMBOL_GPL(reset_shadow_zero_bits_mask);
 
+static inline bool boot_cpu_is_amd(void)
+{
+	WARN_ON_ONCE(!tdp_enabled);
+	return shadow_x_mask == 0;
+}
+
 /*
  * the direct page table on host, use as much mmu features as
  * possible, however, kvm currently does not do execution-protection.
@@ -3764,11 +3775,11 @@ static void
 reset_tdp_shadow_zero_bits_mask(struct kvm_vcpu *vcpu,
 				struct kvm_mmu *context)
 {
-	if (guest_cpuid_is_amd(vcpu))
+	if (boot_cpu_is_amd())
 		__reset_rsvds_bits_mask(vcpu, &context->shadow_zero_check,
 					boot_cpu_data.x86_phys_bits,
 					context->shadow_root_level, false,
-					cpu_has_gbpages, true);
+					cpu_has_gbpages, true, true);
 	else
 		__reset_rsvds_bits_mask_ept(&context->shadow_zero_check,
 					    boot_cpu_data.x86_phys_bits,

arch/x86/kvm/svm.c

@@ -202,6 +202,7 @@ module_param(npt, int, S_IRUGO);
 static int nested = true;
 module_param(nested, int, S_IRUGO);
 
+static void svm_set_cr0(struct kvm_vcpu *vcpu, unsigned long cr0);
 static void svm_flush_tlb(struct kvm_vcpu *vcpu);
 static void svm_complete_interrupts(struct vcpu_svm *svm);
 
@@ -1263,7 +1264,8 @@ static void init_vmcb(struct vcpu_svm *svm, bool init_event)
 	 * svm_set_cr0() sets PG and WP and clears NW and CD on save->cr0.
 	 * It also updates the guest-visible cr0 value.
 	 */
-	(void)kvm_set_cr0(&svm->vcpu, X86_CR0_NW | X86_CR0_CD | X86_CR0_ET);
+	svm_set_cr0(&svm->vcpu, X86_CR0_NW | X86_CR0_CD | X86_CR0_ET);
+	kvm_mmu_reset_context(&svm->vcpu);
 
 	save->cr4 = X86_CR4_PAE;
 	/* rdx = ?? */

arch/x86/kvm/x86.c

@@ -2190,6 +2190,8 @@ int kvm_get_msr_common(struct kvm_vcpu *vcpu, struct msr_data *msr_info)
 	case MSR_IA32_LASTINTFROMIP:
 	case MSR_IA32_LASTINTTOIP:
 	case MSR_K8_SYSCFG:
+	case MSR_K8_TSEG_ADDR:
+	case MSR_K8_TSEG_MASK:
 	case MSR_K7_HWCR:
 	case MSR_VM_HSAVE_PA:
 	case MSR_K8_INT_PENDING_MSG:

arch/x86/pci/common.c

@@ -166,6 +166,7 @@ void pcibios_fixup_bus(struct pci_bus *b)
 {
 	struct pci_dev *dev;
 
+	pci_read_bridge_bases(b);
 	list_for_each_entry(dev, &b->devices, bus_list)
 		pcibios_fixup_device_resources(dev);
 }

arch/xtensa/kernel/pci.c

@@ -210,6 +210,10 @@ subsys_initcall(pcibios_init);
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
+	if (bus->parent) {
+		/* This is a subordinate bridge */
+		pci_read_bridge_bases(bus);
+	}
 }
 
 void pcibios_set_master(struct pci_dev *dev)

drivers/atm/he.c

@@ -1578,9 +1578,7 @@ he_stop(struct he_dev *he_dev)
 
 	kfree(he_dev->rbpl_virt);
 	kfree(he_dev->rbpl_table);
-
-	if (he_dev->rbpl_pool)
-		dma_pool_destroy(he_dev->rbpl_pool);
+	dma_pool_destroy(he_dev->rbpl_pool);
 
 	if (he_dev->rbrq_base)
 		dma_free_coherent(&he_dev->pci_dev->dev, CONFIG_RBRQ_SIZE * sizeof(struct he_rbrq),
@@ -1594,8 +1592,7 @@ he_stop(struct he_dev *he_dev)
 		dma_free_coherent(&he_dev->pci_dev->dev, CONFIG_TBRQ_SIZE * sizeof(struct he_tbrq),
 				  he_dev->tpdrq_base, he_dev->tpdrq_phys);
 
-	if (he_dev->tpd_pool)
-		dma_pool_destroy(he_dev->tpd_pool);
+	dma_pool_destroy(he_dev->tpd_pool);
 
 	if (he_dev->pci_dev) {
 		pci_read_config_word(he_dev->pci_dev, PCI_COMMAND, &command);

drivers/atm/solos-pci.c

@@ -805,7 +805,12 @@ static void solos_bh(unsigned long card_arg)
 					continue;
 				}
 
-				skb = alloc_skb(size + 1, GFP_ATOMIC);
+				/* Use netdev_alloc_skb() because it adds NET_SKB_PAD of
+				 * headroom, and ensures we can route packets back out an
+				 * Ethernet interface (for example) without having to
+				 * reallocate. Adding NET_IP_ALIGN also ensures that both
+				 * PPPoATM and PPPoEoBR2684 packets end up aligned. */
+				skb = netdev_alloc_skb_ip_align(NULL, size + 1);
 				if (!skb) {
 					if (net_ratelimit())
 						dev_warn(&card->dev->dev, "Failed to allocate sk_buff for RX\n");
@@ -869,7 +874,10 @@ static void solos_bh(unsigned long card_arg)
 		/* Allocate RX skbs for any ports which need them */
 		if (card->using_dma && card->atmdev[port] &&
 		    !card->rx_skb[port]) {
-			struct sk_buff *skb = alloc_skb(RX_DMA_SIZE, GFP_ATOMIC);
+			/* Unlike the MMIO case (qv) we can't add NET_IP_ALIGN
+			 * here; the FPGA can only DMA to addresses which are
+			 * aligned to 4 bytes. */
+			struct sk_buff *skb = dev_alloc_skb(RX_DMA_SIZE);
 			if (skb) {
 				SKB_CB(skb)->dma_addr =
 					dma_map_single(&card->dev->dev, skb->data,

drivers/base/cacheinfo.c

@@ -148,7 +148,11 @@ static void cache_shared_cpu_map_remove(unsigned int cpu)
 
 			if (sibling == cpu) /* skip itself */
 				continue;
+
 			sib_cpu_ci = get_cpu_cacheinfo(sibling);
+			if (!sib_cpu_ci->info_list)
+				continue;
+
 			sib_leaf = sib_cpu_ci->info_list + index;
 			cpumask_clear_cpu(cpu, &sib_leaf->shared_cpu_map);
 			cpumask_clear_cpu(sibling, &this_leaf->shared_cpu_map);
@@ -159,6 +163,9 @@ static void cache_shared_cpu_map_remove(unsigned int cpu)
 
 static void free_cache_attributes(unsigned int cpu)
 {
+	if (!per_cpu_cacheinfo(cpu))
+		return;
+
 	cache_shared_cpu_map_remove(cpu);
 
 	kfree(per_cpu_cacheinfo(cpu));
@@ -514,8 +521,7 @@ static int cacheinfo_cpu_callback(struct notifier_block *nfb,
 		break;
 	case CPU_DEAD:
 		cache_remove_dev(cpu);
-		if (per_cpu_cacheinfo(cpu))
-			free_cache_attributes(cpu);
+		free_cache_attributes(cpu);
 		break;
 	}
 	return notifier_from_errno(rc);

drivers/char/hw_random/xgene-rng.c

@@ -344,11 +344,12 @@ static int xgene_rng_probe(struct platform_device *pdev)
 	if (IS_ERR(ctx->csr_base))
 		return PTR_ERR(ctx->csr_base);
 
-	ctx->irq = platform_get_irq(pdev, 0);
-	if (ctx->irq < 0) {
+	rc = platform_get_irq(pdev, 0);
+	if (rc < 0) {
 		dev_err(&pdev->dev, "No IRQ resource\n");
-		return ctx->irq;
+		return rc;
 	}
+	ctx->irq = rc;
 
 	dev_dbg(&pdev->dev, "APM X-Gene RNG BASE %p ALARM IRQ %d",
 		ctx->csr_base, ctx->irq);

drivers/crypto/marvell/cesa.h

@@ -687,6 +687,33 @@ static inline u32 mv_cesa_get_int_mask(struct mv_cesa_engine *engine)
 
 int mv_cesa_queue_req(struct crypto_async_request *req);
 
+/*
+ * Helper function that indicates whether a crypto request needs to be
+ * cleaned up or not after being enqueued using mv_cesa_queue_req().
+ */
+static inline int mv_cesa_req_needs_cleanup(struct crypto_async_request *req,
+					    int ret)
+{
+	/*
+	 * The queue still had some space, the request was queued
+	 * normally, so there's no need to clean it up.
+	 */
+	if (ret == -EINPROGRESS)
+		return false;
+
+	/*
+	 * The queue had not space left, but since the request is
+	 * flagged with CRYPTO_TFM_REQ_MAY_BACKLOG, it was added to
+	 * the backlog and will be processed later. There's no need to
+	 * clean it up.
+	 */
+	if (ret == -EBUSY && req->flags & CRYPTO_TFM_REQ_MAY_BACKLOG)
+		return false;
+
+	/* Request wasn't queued, we need to clean it up */
+	return true;
+}
+
 /* TDMA functions */
 
 static inline void mv_cesa_req_dma_iter_init(struct mv_cesa_dma_iter *iter,

drivers/crypto/marvell/cipher.c

@@ -189,7 +189,6 @@ static inline void mv_cesa_ablkcipher_prepare(struct crypto_async_request *req,
 {
 	struct ablkcipher_request *ablkreq = ablkcipher_request_cast(req);
 	struct mv_cesa_ablkcipher_req *creq = ablkcipher_request_ctx(ablkreq);
-
 	creq->req.base.engine = engine;
 
 	if (creq->req.base.type == CESA_DMA_REQ)
@@ -431,7 +430,7 @@ static int mv_cesa_des_op(struct ablkcipher_request *req,
 		return ret;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS)
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ablkcipher_cleanup(req);
 
 	return ret;
@@ -551,7 +550,7 @@ static int mv_cesa_des3_op(struct ablkcipher_request *req,
 		return ret;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS)
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ablkcipher_cleanup(req);
 
 	return ret;
@@ -693,7 +692,7 @@ static int mv_cesa_aes_op(struct ablkcipher_request *req,
 		return ret;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS)
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ablkcipher_cleanup(req);
 
 	return ret;

drivers/crypto/marvell/hash.c

@@ -739,10 +739,8 @@ static int mv_cesa_ahash_update(struct ahash_request *req)
 		return 0;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS) {
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ahash_cleanup(req);
-		return ret;
-	}
 
 	return ret;
 }
@@ -766,7 +764,7 @@ static int mv_cesa_ahash_final(struct ahash_request *req)
 		return 0;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS)
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ahash_cleanup(req);
 
 	return ret;
@@ -791,7 +789,7 @@ static int mv_cesa_ahash_finup(struct ahash_request *req)
 		return 0;
 
 	ret = mv_cesa_queue_req(&req->base);
-	if (ret && ret != -EINPROGRESS)
+	if (mv_cesa_req_needs_cleanup(&req->base, ret))
 		mv_cesa_ahash_cleanup(req);
 
 	return ret;

drivers/crypto/qat/qat_common/adf_aer.c

@@ -88,6 +88,9 @@ static void adf_dev_restore(struct adf_accel_dev *accel_dev)
 	struct pci_dev *parent = pdev->bus->self;
 	uint16_t bridge_ctl = 0;
 
+	if (accel_dev->is_vf)
+		return;
+
 	dev_info(&GET_DEV(accel_dev), "Resetting device qat_dev%d\n",
 		 accel_dev->accel_id);
 

drivers/extcon/extcon.c

@@ -159,7 +159,7 @@ static int find_cable_index_by_name(struct extcon_dev *edev, const char *name)
 static bool is_extcon_changed(u32 prev, u32 new, int idx, bool *attached)
 {
 	if (((prev >> idx) & 0x1) != ((new >> idx) & 0x1)) {
-		*attached = new ? true : false;
+		*attached = ((new >> idx) & 0x1) ? true : false;
 		return true;
 	}
 

drivers/firmware/Kconfig

@@ -139,6 +139,14 @@ config QCOM_SCM
 	bool
 	depends on ARM || ARM64
 
+config QCOM_SCM_32
+	def_bool y
+	depends on QCOM_SCM && ARM
+
+config QCOM_SCM_64
+	def_bool y
+	depends on QCOM_SCM && ARM64
+
 source "drivers/firmware/broadcom/Kconfig"
 source "drivers/firmware/google/Kconfig"
 source "drivers/firmware/efi/Kconfig"