What happens is that a write to /dev/sg is given a request with non-zero
->iovec_count combined with zero ->dxfer_len. Or with ->dxferp pointing
to an array full of empty iovecs.
Having write permission to /dev/sg shouldn't be equivalent to the
ability to trigger BUG_ON() while holding spinlocks...
Found by Dmitry Vyukov and syzkaller.
[ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the
underlying issue. - Linus ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't crash the machine just because of an empty transfer. Use WARN_ON()
combined with returning an error.
Found by Dmitry Vyukov and syzkaller.
[ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root
cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON()
might still be a cause of excessive log spamming.
NOTE! If this warning ever triggers, we may end up leaking resources,
since this doesn't bother to try to clean the command up. So this
WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is
much worse.
People really need to stop using BUG_ON() for "this shouldn't ever
happen". It makes pretty much any bug worse. - Linus ]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped
check, release the dst before returning an error.
Fixes: ec5e3b0a1d ("ipv6: Inhibit IPv4-mapped src address on the wire.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Arnd Bergmann:
"Two more bugfixes that came in during this week:
- a defconfig change to enable a vital driver used on some Qualcomm
based phones. This was already queued for 4.11, but the maintainer
asked to have it in 4.10 after all.
- a regression fix for the reset controller framework, this got
broken by a typo in the 4.10 merge window"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: enable Qualcomm RPMCC
reset: fix shared reset triggered_count decrement on error
Pull ARM fixes from Russell King:
"A couple of fixes from Kees concerning problems he spotted with our
user access support"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8658/1: uaccess: fix zeroing of 64-bit get_user()
ARM: 8657/1: uaccess: consistently check object sizes
Pull x86 fix from Thomas Gleixner:
"Make the build clean by working around yet another GCC stupidity"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vm86: Fix unused variable warning if THP is disabled
Pull locking fix from Thomas Gleixner:
"Move the futex init function to core initcall so user mode helper does
not run into an uninitialized futex syscall"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Move futex_init() to core_initcall
Pull timer fixes from Thomas Gleixner:
"Two small fixes::
- Prevent deadlock on the tick broadcast lock. Found and fixed by
Mike.
- Stop using printk() in the timekeeping debug code to prevent a
deadlock against the scheduler"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Use deferred printk() in debug code
tick/broadcast: Prevent deadlock on tick_broadcast_lock
Pull networking fixes from David Miller:
1) Fix leak in dpaa_eth error paths, from Dan Carpenter.
2) Use after free when using IPV6_RECVPKTINFO, from Andrey Konovalov.
3) fanout_release() cannot be invoked from atomic contexts, from Anoob
Soman.
4) Fix bogus attempt at lockdep annotation in IRDA.
5) dev_fill_metadata_dst() can OOP on a NULL dst cache pointer, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
irda: Fix lockdep annotations in hashbin_delete().
vxlan: fix oops in dev_fill_metadata_dst
dccp: fix freeing skb too early for IPV6_RECVPKTINFO
dpaa_eth: small leak on error
packet: Do not call fanout_release from atomic contexts
Use rcuidle console tracepoint because, apparently, it may be issued
from an idle CPU:
hw-breakpoint: Failed to enable monitor mode on CPU 0.
hw-breakpoint: CPU 0 failed to disable vector catch
===============================
[ ERR: suspicious RCU usage. ]
4.10.0-rc8-next-20170215+ #119 Not tainted
-------------------------------
./include/trace/events/printk.h:32 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 2, debug_locks = 0
RCU used illegally from extended quiescent state!
2 locks held by swapper/0/0:
#0: (cpu_pm_notifier_lock){......}, at: [<c0237e2c>] cpu_pm_exit+0x10/0x54
#1: (console_lock){+.+.+.}, at: [<c01ab350>] vprintk_emit+0x264/0x474
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-20170215+ #119
Hardware name: Generic OMAP4 (Flattened Device Tree)
console_unlock
vprintk_emit
vprintk_default
printk
reset_ctrl_regs
dbg_cpu_pm_notify
notifier_call_chain
cpu_pm_exit
omap_enter_idle_coupled
cpuidle_enter_state
cpuidle_enter_state_coupled
do_idle
cpu_startup_entry
start_kernel
This RCU warning, however, is suppressed by lockdep_off() in printk().
lockdep_off() increments the ->lockdep_recursion counter and thus
disables RCU_LOCKDEP_WARN() and debug_lockdep_rcu_enabled(), which want
lockdep to be enabled "current->lockdep_recursion == 0".
Link: http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk@armlinux.org.uk>
Cc: <stable@vger.kernel.org> [3.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A nested lock depth was added to the hasbin_delete() code but it
doesn't actually work some well and results in tons of lockdep splats.
Fix the code instead to properly drop the lock around the operation
and just keep peeking the head of the hashbin queue.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block layer fix from Jens Axboe:
"A single fix for a lockdep splat reported by Thomas and Gabriel"
* 'for-linus' of git://git.kernel.dk/linux-block:
cfq-iosched: don't call wbt_disable_default() with IRQs disabled
Since the commit 0c1d70af92 ("net: use dst_cache for vxlan device")
vxlan_fill_metadata_dst() calls vxlan_get_route() passing a NULL
dst_cache pointer, so the latter should explicitly check for
valid dst_cache ptr. Unfortunately the commit d71785ffc7 ("net: add
dst_cache to ovs vxlan lwtunnel") removed said check.
As a result is possible to trigger a null pointer access calling
vxlan_fill_metadata_dst(), e.g. with:
ovs-vsctl add-br ovs-br0
ovs-vsctl add-port ovs-br0 vxlan0 -- set interface vxlan0 \
type=vxlan options:remote_ip=192.168.1.1 \
options:key=1234 options:dst_port=4789 ofport_request=10
ip address add dev ovs-br0 172.16.1.2/24
ovs-vsctl set Bridge ovs-br0 ipfix=@i -- --id=@i create IPFIX \
targets=\"172.16.1.1:1234\" sampling=1
iperf -c 172.16.1.1 -u -l 1000 -b 10M -t 1 -p 1234
This commit addresses the issue passing to vxlan_get_route() the
dst_cache already available into the lwt info processed by
vxlan_fill_metadata_dst().
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet
is forcibly freed via __kfree_skb in dccp_rcv_state_process if
dccp_v6_conn_request successfully returns.
However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb
is saved to ireq->pktopts and the ref count for skb is incremented in
dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed
in dccp_rcv_state_process.
Fix by calling consume_skb instead of doing goto discard and therefore
calling __kfree_skb.
Similar fixes for TCP:
fb7e2399ec [TCP]: skb is unexpectedly freed.
0aea76d35c tcp: SYN packets are now
simply consumed
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fix from Michael Ellerman:
"One fix from Paul: we can not use the radix MMU under a hypervisor for
now.
Although the code checked if the processor supports radix, that is not
sufficient"
* tag 'powerpc-4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Disable use of radix under a hypervisor
Pull input fix from Dmitry Torokhov:
"Just a single change to Elan touchpad driver to recognize a new ACPI
ID"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ELAN0605 to the ACPI table
Pull i2c fix from Wolfram Sang:
"I2C has a revert to fix a regression"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: designware: detect when dynamic tar update is possible"
Pull MMC fix from Ulf Hansson:
"Fix multi-bit bus width without high-speed mode for MMC"
* tag 'mmc-v4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: fix multi-bit bus width without high-speed mode
Pull NTB bugfixes frfom Jon Mason:
"NTB bug fixes to address a crash when unloading the ntb module, a DMA
engine unmap leak, allowing the proper queue choice, and clearing the
SKX irq bit"
* tag 'ntb-4.10-bugfixes' of git://github.com/jonmason/ntb:
ntb: ntb_hw_intel: link_poll isn't clearing the pending status properly
ntb_transport: Pick an unused queue
ntb: ntb_perf missing dmaengine_unmap_put
NTB: ntb_transport: fix debugfs_remove_recursive
This should be >= instead of > here. It means that we don't increment
the free count enough so it becomes off by one.
Fixes: 9ad1a37493 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull "Reset controller fixes for v4.10" from Philipp Zabel:
- Remove erroneous negation of the error check of the reset function
to decrement trigger_count in the error case, not on success. This
fixes shared resets to actually only trigger once, as intended.
* tag 'reset-for-4.10-fixes' of https://git.pengutronix.de/git/pza/linux:
reset: fix shared reset triggered_count decrement on error
For a shared reset, when the reset is successful, the triggered_count is
incremented when trying to call the reset callback, so that another device
sharing the same reset line won't trigger it again. If the reset has not
been triggered successfully, the trigger_count should be decremented.
The code does the opposite, and decrements the trigger_count on success.
As a consequence, another device sharing the reset will be able to trigger
it again.
Fixed be removing negation in from of the error code of the reset function.
Fixes: 7da33a37b4 ("reset: allow using reset_control_reset with shared reset")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit. Adding a new function for SKX that handles clearing of status bit the
right way.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fix typo causing ntb_transport_create_queue to select the first
queue every time, instead of using the next free queue.
Signed-off-by: Thomas VanSelus <tvanselus@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: fce8a7bb5 ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In the normal I/O execution path, ntb_perf is missing a call to
dmaengine_unmap_put() after submission. That causes us to leak
unmap objects.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a77 ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level
directory must not be later than
debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory.
Otherwise, the sub-level directory will not exist, and it would be
invalid (panic) to attempt to remove it. This removes the top-level
directory last, after sub-level directories have been cleaned up.
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: e26a5843f ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull drm fixes from Dave Airlie:
"Just two last minute fixes, one for DP MST oopses and one for a radeon
regression"
* tag 'drm-fixes-for-v4.10-final' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Use mode h/vdisplay fields to hide out of bounds HW cursor
drm/dp/mst: fix kernel oops when turning off secondary monitor
One regression fix for interlaced modes on radeon
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Use mode h/vdisplay fields to hide out of bounds HW cursor
This reverts commit 24b91e360e and commit
7bdb59f1ad ("tick/nohz: Fix possible missing clock reprog after tick
soft restart") that depends on it,
Pavel reports that it causes occasional boot hangs for him that seem to
depend on just how the machine was booted. In particular, his machine
hangs at around the PCI fixups of the EHCI USB host controller, but only
hangs from cold boot, not from a warm boot.
Thomas Gleixner suspecs it's a CPU hotplug interaction, particularly
since Pavel also saw suspend/resume issues that seem to be related.
We're reverting for now while trying to figure out the root cause.
Reported-bisected-and-tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # reverted commits were marked for stable
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull media fix from Mauro Carvalho Chehab:
"A regression fix that makes the Siano driver to work again after the
CONFIG_VMAP_STACK change"
* tag 'media/v4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] siano: make it work again with CONFIG_VMAP_STACK
Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer. Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.
Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # 2.6.17+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull fuse fixes from Miklos Szeredi:
"Fix a use after free bug introduced in 4.2 and using an uninitialized
value introduced in 4.9"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix uninitialized flags in pipe_buffer
fuse: fix use after free issue in fuse_dev_do_read()
Pull PCI fix from Bjorn Helgaas:
"Add back pcie_pme_remove() so we free the IRQ when removing PCIe port
devices; previously the leaked IRQ caused an MSI BUG_ON"
* tag 'pci-v4.10-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PME: Restore pcie_pme_driver.remove
Pull networking fixes from David Miller:
1) In order to avoid problems in the future, make cgroup bpf overriding
explicit using BPF_F_ALLOW_OVERRIDE. From Alexei Staovoitov.
2) LLC sets skb->sk without proper skb->destructor and this explodes,
fix from Eric Dumazet.
3) Make sure when we have an ipv4 mapped source address, the
destination is either also an ipv4 mapped address or
ipv6_addr_any(). Fix from Jonathan T. Leighton.
4) Avoid packet loss in fec driver by programming the multicast filter
more intelligently. From Rui Sousa.
5) Handle multiple threads invoking fanout_add(), fix from Eric
Dumazet.
6) Since we can invoke the TCP input path in process context, without
BH being disabled, we have to accomodate that in the locking of the
TCP probe. Also from Eric Dumazet.
7) Fix erroneous emission of NETEVENT_DELAY_PROBE_TIME_UPDATE when we
aren't even updating that sysctl value. From Marcus Huewe.
8) Fix endian bugs in ibmvnic driver, from Thomas Falcon.
[ This is the second version of the pull that reverts the nested
rhashtable changes that looked a bit too scary for this late in the
release - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
rhashtable: Revert nested table changes.
ibmvnic: Fix endian errors in error reporting output
ibmvnic: Fix endian error when requesting device capabilities
net: neigh: Fix netevent NETEVENT_DELAY_PROBE_TIME_UPDATE notification
net: xilinx_emaclite: fix freezes due to unordered I/O
net: xilinx_emaclite: fix receive buffer overflow
bpf: kernel header files need to be copied into the tools directory
tcp: tcp_probe: use spin_lock_bh()
uapi: fix linux/if_pppol2tp.h userspace compilation errors
packet: fix races in fanout_add()
ibmvnic: Fix initial MTU settings
net: ethernet: ti: cpsw: fix cpsw assignment in resume
kcm: fix a null pointer dereference in kcm_sendmsg()
net: fec: fix multicast filtering hardware setup
ipv6: Handle IPv4-mapped src to in6addr_any dst.
ipv6: Inhibit IPv4-mapped src address on the wire.
net/mlx5e: Disable preemption when doing TC statistics upcall
rhashtable: Add nested tables
tipc: Fix tipc_sk_reinit race conditions
gfs2: Use rhashtable walk interface in glock_hash_walk
...
The 64-bit get_user() wasn't clearing the high word due to a typo in the
error handler. The exception handler entry was already correct, though.
Noticed during recent usercopy test additions in lib/test_user_copy.c.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
In commit 76624175dc ("arm64: uaccess: consistently check object sizes"),
the object size checks are moved outside the access_ok() so that bad
destinations are detected before hitting the "memset(dest, 0, size)" in the
copy_from_user() failure path.
This makes the same change for arm, with attention given to possibly
extracting the uaccess routines into a common header file for all
architectures in the future.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
wbt_disable_default() calls del_timer_sync() to wait for the wbt
timer to finish before disabling throttling. We can't do this with
IRQs disable. This fixes a lockdep splat on boot, if non-root
cgroups are used.
Reported-by: Gabriel C <nix.or.die@gmail.com>
Fixes: 87760e5eef ("block: hook up writeback throttling")
Signed-off-by: Jens Axboe <axboe@fb.com>
This reverts commits:
6a254780779dbbfb0ab640137906c5
It's too risky to put in this late in the release
cycle. We'll put these changes into the next merge
window instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
dp/mst oops fix for v4.10
* tag 'drm-misc-fixes-2017-02-15' of git://anongit.freedesktop.org/git/drm-misc:
drm/dp/mst: fix kernel oops when turning off secondary monitor
Currently, if the kernel is running on a POWER9 processor under a
hypervisor, it may try to use the radix MMU even though it doesn't have
the necessary code to do so (it doesn't negotiate use of radix, and it
doesn't do the H_REGISTER_PROC_TBL hcall). If the hypervisor supports
both radix and HPT, then it will set up the guest to use HPT (since the
guest doesn't request radix in the CAS call), but if the radix feature
bit is set in the ibm,pa-features property (which is valid, since
ibm,pa-features is defined to represent the capabilities of the
processor) the guest will try to use radix, resulting in a crash when
it turns the MMU on.
This makes the minimal fix for the current code, which is to disable
radix unless we are running in hypervisor mode.
Fixes: 2bfd65e45e ("powerpc/mm/radix: Add radix callbacks for early init routines")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a neigh related sysctl parameter, we always send a
NETEVENT_DELAY_PROBE_TIME_UPDATE netevent. For instance, when
executing
sysctl net.ipv6.neigh.wlp3s0.retrans_time_ms=2000
a NETEVENT_DELAY_PROBE_TIME_UPDATE netevent is generated.
This is caused by commit 2a4501ae18 ("neigh: Send a
notification when DELAY_PROBE_TIME changes"). According to the
commit's description, it was intended to generate such an event
when setting the "delay_first_probe_time" sysctl parameter.
In order to fix this, only generate this event when actually
setting the "delay_first_probe_time" sysctl parameter. This fix
should not have any unintended side-effects, because all but one
registered netevent callbacks check for other netevent event
types (the registered callbacks were obtained by grepping for
"register_netevent_notifier"). The only callback that uses the
NETEVENT_DELAY_PROBE_TIME_UPDATE event is
mlxsw_sp_router_netevent_event() (in
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c): in case
of this event, it only accesses the DELAY_PROBE_TIME of the
passed neigh_parms.
Fixes: 2a4501ae18 ("neigh: Send a notification when DELAY_PROBE_TIME changes")
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.
The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.
I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.
In commit 123c1407af ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.
Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.
Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407af ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.
Fix those cases.
Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential race between fuse_dev_do_write()
and request_wait_answer() contexts as shown below:
TASK 1:
__fuse_request_send():
|--spin_lock(&fiq->waitq.lock);
|--queue_request();
|--spin_unlock(&fiq->waitq.lock);
|--request_wait_answer():
|--if (test_bit(FR_SENT, &req->flags))
<gets pre-empted after it is validated true>
TASK 2:
fuse_dev_do_write():
|--clears bit FR_SENT,
|--request_end():
|--sets bit FR_FINISHED
|--spin_lock(&fiq->waitq.lock);
|--list_del_init(&req->intr_entry);
|--spin_unlock(&fiq->waitq.lock);
|--fuse_put_request();
|--queue_interrupt();
<request gets queued to interrupts list>
|--wake_up_locked(&fiq->waitq);
|--wait_event_freezable();
<as FR_FINISHED is set, it returns and then
the caller frees this request>
Now, the next fuse_dev_do_read(), see interrupts list is not empty
and then calls fuse_read_interrupt() which tries to access the request
which is already free'd and gets the below crash:
[11432.401266] Unable to handle kernel paging request at virtual address
6b6b6b6b6b6b6b6b
...
[11432.418518] Kernel BUG at ffffff80083720e0
[11432.456168] PC is at __list_del_entry+0x6c/0xc4
[11432.463573] LR is at fuse_dev_do_read+0x1ac/0x474
...
[11432.679999] [<ffffff80083720e0>] __list_del_entry+0x6c/0xc4
[11432.687794] [<ffffff80082c65e0>] fuse_dev_do_read+0x1ac/0x474
[11432.693180] [<ffffff80082c6b14>] fuse_dev_read+0x6c/0x78
[11432.699082] [<ffffff80081d5638>] __vfs_read+0xc0/0xe8
[11432.704459] [<ffffff80081d5efc>] vfs_read+0x90/0x108
[11432.709406] [<ffffff80081d67f0>] SyS_read+0x58/0x94
As FR_FINISHED bit is set before deleting the intr_entry with input
queue lock in request completion path, do the testing of this flag and
queueing atomically with the same lock in queue_interrupt().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: fd22d62ed0 ("fuse: no fc->lock for iqueue parts")
Cc: <stable@vger.kernel.org> # 4.2+
tcp_rcv_established() can now run in process context.
We need to disable BH while acquiring tcp probe spinlock,
or risk a deadlock.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of <linux/libc-compat.h> interface limitations, <netinet/in.h>
provided by libc cannot be included after <linux/in.h>, therefore any
header that includes <netinet/in.h> cannot be included after <linux/in.h>.
Change uapi/linux/l2tp.h, the last uapi header that includes
<netinet/in.h>, to include <linux/in.h> and <linux/in6.h> instead of
<netinet/in.h> and use __SOCK_SIZE__ instead of sizeof(struct sockaddr)
the same way as uapi/linux/in.h does, to fix linux/if_pppol2tp.h userspace
compilation errors like this:
In file included from /usr/include/linux/l2tp.h:12:0,
from /usr/include/linux/if_pppol2tp.h:21,
/usr/include/netinet/in.h:31:8: error: redefinition of 'struct in_addr'
Fixes: 47c3e7783b ("net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Tested with USB ID 2040:5510: Hauppauge Windham
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Multiple threads can call fanout_add() at the same time.
We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.
Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.
Fixes: dc99f60069 ("packet: Add fanout support.")
Fixes: 0648ab70af ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan T. Leighton says:
====================
IPv4-mapped on wire, :: dst address issue
Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.
linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull media fixes from Mauro Carvalho Chehab:
"A colorspace regression fix in V4L2 core and a CEC core bug that makes
it discard valid messages"
* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: initiator should be the same as the destination for, poll
[media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB
Commit 577fb13199 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().
However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.
This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.
Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.
Tested with a Zynq-7000 PicoZed 7020 board.
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Herbert Xu says:
====================
rhashtable: Handle table allocation failure during insertion
v2 -
Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.
v1 -
This series tackles the problem of table allocation failures during
insertion. The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.
The first two patches removes manual hash table walks which cannot
work on a nested table.
The final patch introduces nested tables.
I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion. As we cannot use vmalloc, we solve it by making our
hash table nested. That is, we allocate single pages at each level
and reach our desired table size by nesting them.
When a nested table is created, only a single page is allocated
at the top-level. Lower levels are allocated on demand during
insertion. Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.
After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible. Also,
the rehash code will never rehash into a nested table. If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems with the function tipc_sk_reinit. Firstly
it's doing a manual walk over an rhashtable. This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.
Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.
This patch fixes both problems.
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function glock_hash_walk walks the rhashtable by hand. This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.
This patch replaces the manual walk by using the rhashtable walk
interface.
Fixes: 88ffbf3e03 ("GFS2: Use resizable hash table for glocks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized. For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
172.20.1.99 0x3 0x0 * bpq0
The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:
$ arp
Address HWtype HWaddress Flags Mask Iface
gateway ether 52:54:00:00:5d:5f C ens3
172.20.1.99 (incomplete) ens3
This changes the content of /proc/net/arp to:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
172.20.1.99 0x3 0x0 * * bpq0
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
To do so it change ax2asc to put the string "*" in buf for a NULL address
argument. Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC complains about unused variable 'vma' in mark_screen_rdonly() if THP is
disabled:
arch/x86/kernel/vm86_32.c: In function ‘mark_screen_rdonly’:
arch/x86/kernel/vm86_32.c:180:26: warning: unused variable ‘vma’
[-Wunused-variable]
struct vm_area_struct *vma = find_vma(mm, 0xA0000);
That's silly. pmd_trans_huge() resolves to 0 when THP is disabled, so the
whole block should be eliminated.
Moving the variable declaration outside the if() block shuts GCC up.
Reported-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: Carlos O'Donell <carlos@redhat.com>
Link: http://lkml.kernel.org/r/20170213125228.63645-1-kirill.shutemov@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ghostprotocols.net domain is not working, remove it from CREDITS and
MAINTAINERS, and change the status to "Odd fixes", and since I haven't
been maintaining those, remove my address from there.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Poll messages that are used to allocate a logical address should
use the same initiator as the destination. Instead, it expected that
the initiator was 0xf which is not according to the standard.
This also had consequences for the message checks in cec_transmit_msg_fh
that incorrectly rejected poll messages with the same initiator and
destination.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts 'commit 7e0739cd9c ("[media] videodev2.h: fix
sYCC/AdobeYCC default quantization range").
The problem is that many drivers can convert R'G'B' content (often
from sensors) to Y'CbCr, but they all produce limited range Y'CbCr.
To stay backwards compatible the default quantization range for
sRGB and AdobeRGB Y'CbCr encoding should be limited range, not full
range, even though the corresponding standards specify full range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT define accordingly and
also update the documentation.
Fixes: 7e0739cd9c ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.9 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The UEVENT user mode helper is enabled before the initcalls are executed
and is available when the root filesystem has been mounted.
The user mode helper is triggered by device init calls and the executable
might use the futex syscall.
futex_init() is marked __initcall which maps to device_initcall, but there
is no guarantee that futex_init() is invoked _before_ the first device init
call which triggers the UEVENT user mode helper.
If the user mode helper uses the futex syscall before futex_init() then the
syscall crashes with a NULL pointer dereference because the futex subsystem
has not been initialized yet.
Move futex_init() to core_initcall so futexes are initialized before the
root filesystem is mounted and the usermode helper becomes available.
[ tglx: Rewrote changelog ]
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Cc: jiang.biao2@zte.com.cn
Cc: jiang.zhengxiong@zte.com.cn
Cc: zhong.weidong@zte.com.cn
Cc: deng.huali@zte.com.cn
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cn
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick_broadcast_lock is taken from interrupt context, but the following call
chain takes the lock without disabling interrupts:
[ 12.703736] _raw_spin_lock+0x3b/0x50
[ 12.703738] tick_broadcast_control+0x5a/0x1a0
[ 12.703742] intel_idle_cpu_online+0x22/0x100
[ 12.703744] cpuhp_invoke_callback+0x245/0x9d0
[ 12.703752] cpuhp_thread_fun+0x52/0x110
[ 12.703754] smpboot_thread_fn+0x276/0x320
So the following deadlock can happen:
lock(tick_broadcast_lock);
<Interrupt>
lock(tick_broadcast_lock);
intel_idle_cpu_online() is the only place which violates the calling
convention of tick_broadcast_control(). This was caused by the removal of
the smp function call in course of the cpu hotplug rework.
Instead of slapping local_irq_disable/enable() at the call site, we can
relax the calling convention and handle it in the core code, which makes
the whole machinery more robust.
Fixes: 29d7bbada9 ("intel_idle: Remove superfluous SMP fuction call")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Ruslan Ruslichenko <rruslich@cisco.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: lwn@lwn.net
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1486953115.5912.4.camel@gmx.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It seems nobody used LLC since linux-3.12.
Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.
Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.
Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.
Fixes: 376c7311bd ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.
Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X
2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.
3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.
In the future this behavior may be extended with a chain of
non-overridable programs.
Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.
Add several testcases and adjust libbpf.
Fixes: 3007098494 ("cgroup: add support for eBPF programs")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ELAN0605 has been confirmed to be a variant of ELAN0600, which is
blacklisted in the hid-core to be managed by elan_i2c. This device can be
found in Lenovo ideapad 310s (80U4000).
Signed-off-by: Hiroka IHARA <ihara_h@live.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-11 21:23:43 -05:00
69 changed files with 568 additions and 346 deletions
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
