Linux 3.6-rc5

Pull DMA-mapping fixes from Marek Szyprowski:
 "Another set of fixes for ARM dma-mapping subsystem.

  Commit e9da6e9905 replaced custom consistent buffer remapping code
  with generic vmalloc areas.  It however introduced some regressions
  caused by limited support for allocations in atomic context.  This
  series contains fixes for those regressions.

  For some subplatforms the default, pre-allocated pool for atomic
  allocations turned out to be too small, so a function for setting its
  size has been added.

  Another set of patches adds support for atomic allocations to
  IOMMU-aware DMA-mapping implementation.

  The last part of this pull request contains two fixes for Contiguous
  Memory Allocator, which relax too strict requirements."

* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
  ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
  ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
  ARM: dma-mapping: atomic_pool with struct page **pages
  ARM: Kirkwood: increase atomic coherent pool size
  ARM: DMA-Mapping: print warning when atomic coherent allocation fails
  ARM: DMA-Mapping: add function for setting coherent pool size from platform code
  ARM: relax conditions required for enabling Contiguous Memory Allocator
  mm: cma: fix alignment requirements for contiguous regions

Documentation/ABI/testing/sysfs-bus-pci

@@ -210,3 +210,15 @@ Users:
 		firmware assigned instance number of the PCI
 		device that can help in understanding the firmware
 		intended order of the PCI device.
+
+What:		/sys/bus/pci/devices/.../d3cold_allowed
+Date:		July 2012
+Contact:	Huang Ying <ying.huang@intel.com>
+Description:
+		d3cold_allowed is bit to control whether the corresponding PCI
+		device can be put into D3Cold state.  If it is cleared, the
+		device will never be put into D3Cold state.  If it is set, the
+		device may be put into D3Cold state if other requirements are
+		satisfied too.  Reading this attribute will show the current
+		value of d3cold_allowed bit.  Writing this attribute will set
+		the value of d3cold_allowed bit.

Documentation/ABI/testing/sysfs-platform-ideapad-laptop

@@ -5,4 +5,15 @@ Contact:	"Ike Panhc <ike.pan@canonical.com>"
 Description:
 		Control the power of camera module. 1 means on, 0 means off.
 
+What:		/sys/devices/platform/ideapad/fan_mode
+Date:		June 2012
+KernelVersion:	3.6
+Contact:	"Maxim Mikityanskiy <maxtram95@gmail.com>"
+Description:
+		Change fan mode
+		There are four available modes:
+			* 0 -> Super Silent Mode
+			* 1 -> Standard Mode
+			* 2 -> Dust Cleaning
+			* 4 -> Efficient Thermal Dissipation Mode
 

Documentation/DocBook/filesystems.tmpl

@@ -224,8 +224,8 @@ all your transactions.
 </para>
 
 <para>
-Then at umount time , in your put_super() (2.4) or write_super() (2.5)
-you can then call journal_destroy() to clean up your in-core journal object.
+Then at umount time , in your put_super() you can then call journal_destroy()
+to clean up your in-core journal object.
 </para>
 
 <para>

Documentation/DocBook/media/v4l/vidioc-g-tuner.xml

@@ -125,7 +125,7 @@ the structure refers to a radio tuner the
 <constant>V4L2_TUNER_CAP_NORM</constant> flags can't be used.</para>
 <para>If multiple frequency bands are supported, then
 <structfield>capability</structfield> is the union of all
-<structfield>capability></structfield> fields of each &v4l2-frequency-band;.
+<structfield>capability</structfield> fields of each &v4l2-frequency-band;.
 </para></entry>
 	  </row>
 	  <row>

Documentation/block/00-INDEX

@@ -3,15 +3,21 @@
 biodoc.txt
 	- Notes on the Generic Block Layer Rewrite in Linux 2.5
 capability.txt
-	- Generic Block Device Capability (/sys/block/<disk>/capability)
+	- Generic Block Device Capability (/sys/block/<device>/capability)
+cfq-iosched.txt
+	- CFQ IO scheduler tunables
+data-integrity.txt
+	- Block data integrity
 deadline-iosched.txt
 	- Deadline IO scheduler tunables
 ioprio.txt
 	- Block io priorities (in CFQ scheduler)
+queue-sysfs.txt
+	- Queue's sysfs entries
 request.txt
 	- The members of struct request (in include/linux/blkdev.h)
 stat.txt
-	- Block layer statistics in /sys/block/<dev>/stat
+	- Block layer statistics in /sys/block/<device>/stat
 switching-sched.txt
 	- Switching I/O schedulers at runtime
 writeback_cache_control.txt

Documentation/block/cfq-iosched.txt

@@ -1,3 +1,14 @@
+CFQ (Complete Fairness Queueing)
+===============================
+
+The main aim of CFQ scheduler is to provide a fair allocation of the disk
+I/O bandwidth for all the processes which requests an I/O operation.
+
+CFQ maintains the per process queue for the processes which request I/O
+operation(syncronous requests). In case of asynchronous requests, all the
+requests from all the processes are batched together according to their
+process's I/O priority.
+
 CFQ ioscheduler tunables
 ========================
 
@@ -25,6 +36,72 @@ there are multiple spindles behind single LUN (Host based hardware RAID
 controller or for storage arrays), setting slice_idle=0 might end up in better
 throughput and acceptable latencies.
 
+back_seek_max
+-------------
+This specifies, given in Kbytes, the maximum "distance" for backward seeking.
+The distance is the amount of space from the current head location to the
+sectors that are backward in terms of distance.
+
+This parameter allows the scheduler to anticipate requests in the "backward"
+direction and consider them as being the "next" if they are within this
+distance from the current head location.
+
+back_seek_penalty
+-----------------
+This parameter is used to compute the cost of backward seeking. If the
+backward distance of request is just 1/back_seek_penalty from a "front"
+request, then the seeking cost of two requests is considered equivalent.
+
+So scheduler will not bias toward one or the other request (otherwise scheduler
+will bias toward front request). Default value of back_seek_penalty is 2.
+
+fifo_expire_async
+-----------------
+This parameter is used to set the timeout of asynchronous requests. Default
+value of this is 248ms.
+
+fifo_expire_sync
+----------------
+This parameter is used to set the timeout of synchronous requests. Default
+value of this is 124ms. In case to favor synchronous requests over asynchronous
+one, this value should be decreased relative to fifo_expire_async.
+
+slice_async
+-----------
+This parameter is same as of slice_sync but for asynchronous queue. The
+default value is 40ms.
+
+slice_async_rq
+--------------
+This parameter is used to limit the dispatching of asynchronous request to
+device request queue in queue's slice time. The maximum number of request that
+are allowed to be dispatched also depends upon the io priority. Default value
+for this is 2.
+
+slice_sync
+----------
+When a queue is selected for execution, the queues IO requests are only
+executed for a certain amount of time(time_slice) before switching to another
+queue. This parameter is used to calculate the time slice of synchronous
+queue.
+
+time_slice is computed using the below equation:-
+time_slice = slice_sync + (slice_sync/5 * (4 - prio)). To increase the
+time_slice of synchronous queue, increase the value of slice_sync. Default
+value is 100ms.
+
+quantum
+-------
+This specifies the number of request dispatched to the device queue. In a
+queue's time slice, a request will not be dispatched if the number of request
+in the device exceeds this parameter. This parameter is used for synchronous
+request.
+
+In case of storage with several disk, this setting can limit the parallel
+processing of request. Therefore, increasing the value can imporve the
+performace although this can cause the latency of some I/O to increase due
+to more number of requests.
+
 CFQ IOPS Mode for group scheduling
 ===================================
 Basic CFQ design is to provide priority based time slices. Higher priority

Documentation/block/queue-sysfs.txt

@@ -9,20 +9,71 @@ These files are the ones found in the /sys/block/xxx/queue/ directory.
 Files denoted with a RO postfix are readonly and the RW postfix means
 read-write.
 
+add_random (RW)
+----------------
+This file allows to trun off the disk entropy contribution. Default
+value of this file is '1'(on).
+
+discard_granularity (RO)
+-----------------------
+This shows the size of internal allocation of the device in bytes, if
+reported by the device. A value of '0' means device does not support
+the discard functionality.
+
+discard_max_bytes (RO)
+----------------------
+Devices that support discard functionality may have internal limits on
+the number of bytes that can be trimmed or unmapped in a single operation.
+The discard_max_bytes parameter is set by the device driver to the maximum
+number of bytes that can be discarded in a single operation. Discard
+requests issued to the device must not exceed this limit. A discard_max_bytes
+value of 0 means that the device does not support discard functionality.
+
+discard_zeroes_data (RO)
+------------------------
+When read, this file will show if the discarded block are zeroed by the
+device or not. If its value is '1' the blocks are zeroed otherwise not.
+
 hw_sector_size (RO)
 -------------------
 This is the hardware sector size of the device, in bytes.
 
+iostats (RW)
+-------------
+This file is used to control (on/off) the iostats accounting of the
+disk.
+
+logical_block_size (RO)
+-----------------------
+This is the logcal block size of the device, in bytes.
+
 max_hw_sectors_kb (RO)
 ----------------------
 This is the maximum number of kilobytes supported in a single data transfer.
 
+max_integrity_segments (RO)
+---------------------------
+When read, this file shows the max limit of integrity segments as
+set by block layer which a hardware controller can handle.
+
 max_sectors_kb (RW)
 -------------------
 This is the maximum number of kilobytes that the block layer will allow
 for a filesystem request. Must be smaller than or equal to the maximum
 size allowed by the hardware.
 
+max_segments (RO)
+-----------------
+Maximum number of segments of the device.
+
+max_segment_size (RO)
+---------------------
+Maximum segment size of the device.
+
+minimum_io_size (RO)
+--------------------
+This is the smallest preferred io size reported by the device.
+
 nomerges (RW)
 -------------
 This enables the user to disable the lookup logic involved with IO
@@ -45,11 +96,24 @@ per-block-cgroup request pool.  IOW, if there are N block cgroups,
 each request queue may have upto N request pools, each independently
 regulated by nr_requests.
 
+optimal_io_size (RO)
+--------------------
+This is the optimal io size reported by the device.
+
+physical_block_size (RO)
+------------------------
+This is the physical block size of device, in bytes.
+
 read_ahead_kb (RW)
 ------------------
 Maximum number of kilobytes to read-ahead for filesystems on this block
 device.
 
+rotational (RW)
+---------------
+This file is used to stat if the device is of rotational type or
+non-rotational type.
+
 rq_affinity (RW)
 ----------------
 If this option is '1', the block layer will migrate request completions to the

Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt

@@ -10,8 +10,8 @@ Required properties:
 - compatible : Should be "fsl,<chip>-esdhc"
 
 Optional properties:
-- fsl,cd-internal : Indicate to use controller internal card detection
-- fsl,wp-internal : Indicate to use controller internal write protection
+- fsl,cd-controller : Indicate to use controller internal card detection
+- fsl,wp-controller : Indicate to use controller internal write protection
 
 Examples:
 
@@ -19,8 +19,8 @@ esdhc@70004000 {
 	compatible = "fsl,imx51-esdhc";
 	reg = <0x70004000 0x4000>;
 	interrupts = <1>;
-	fsl,cd-internal;
-	fsl,wp-internal;
+	fsl,cd-controller;
+	fsl,wp-controller;
 };
 
 esdhc@70008000 {

Documentation/devicetree/bindings/regulator/tps6586x.txt

@@ -9,9 +9,9 @@ Required properties:
 - regulators: list of regulators provided by this controller, must have
   property "regulator-compatible" to match their hardware counterparts:
   sm[0-2], ldo[0-9] and ldo_rtc
-- sm0-supply: The input supply for the SM0.
-- sm1-supply: The input supply for the SM1.
-- sm2-supply: The input supply for the SM2.
+- vin-sm0-supply: The input supply for the SM0.
+- vin-sm1-supply: The input supply for the SM1.
+- vin-sm2-supply: The input supply for the SM2.
 - vinldo01-supply: The input supply for the LDO1 and LDO2
 - vinldo23-supply: The input supply for the LDO2 and LDO3
 - vinldo4-supply: The input supply for the LDO4
@@ -30,9 +30,9 @@ Example:
 		#gpio-cells = <2>;
 		gpio-controller;
 
-		sm0-supply = <&some_reg>;
-		sm1-supply = <&some_reg>;
-		sm2-supply = <&some_reg>;
+		vin-sm0-supply = <&some_reg>;
+		vin-sm1-supply = <&some_reg>;
+		vin-sm2-supply = <&some_reg>;
 		vinldo01-supply = <...>;
 		vinldo23-supply = <...>;
 		vinldo4-supply = <...>;

Documentation/feature-removal-schedule.txt

@@ -579,7 +579,7 @@ Why:	KVM tracepoints provide mostly equivalent information in a much more
 ----------------------------
 
 What:	at91-mci driver ("CONFIG_MMC_AT91")
-When:	3.7
+When:	3.8
 Why:	There are two mci drivers: at91-mci and atmel-mci. The PDC support
 	was added to atmel-mci as a first step to support more chips.
 	Then at91-mci was kept only for old IP versions (on at91rm9200 and

Documentation/filesystems/Locking

@@ -114,7 +114,6 @@ prototypes:
 	int (*drop_inode) (struct inode *);
 	void (*evict_inode) (struct inode *);
 	void (*put_super) (struct super_block *);
-	void (*write_super) (struct super_block *);
 	int (*sync_fs)(struct super_block *sb, int wait);
 	int (*freeze_fs) (struct super_block *);
 	int (*unfreeze_fs) (struct super_block *);
@@ -136,7 +135,6 @@ write_inode:
 drop_inode:				!!!inode->i_lock!!!
 evict_inode:
 put_super:		write
-write_super:		read
 sync_fs:		read
 freeze_fs:		write
 unfreeze_fs:		write

Documentation/filesystems/porting

@@ -94,9 +94,8 @@ protected.
 ---
 [mandatory]
 
-BKL is also moved from around sb operations.  ->write_super() Is now called 
-without BKL held.  BKL should have been shifted into individual fs sb_op
-functions.  If you don't need it, remove it.  
+BKL is also moved from around sb operations. BKL should have been shifted into
+individual fs sb_op functions.  If you don't need it, remove it.
 
 ---
 [informational]

Documentation/filesystems/vfat.txt

@@ -137,6 +137,17 @@ errors=panic|continue|remount-ro
 		 without doing anything or remount the partition in
 		 read-only mode (default behavior).
 
+discard       -- If set, issues discard/TRIM commands to the block
+		 device when blocks are freed. This is useful for SSD devices
+		 and sparse/thinly-provisoned LUNs.
+
+nfs           -- This option maintains an index (cache) of directory
+		 inodes by i_logstart which is used by the nfs-related code to
+		 improve look-ups.
+
+		 Enable this only if you want to export the FAT filesystem
+		 over NFS
+
 <bool>: 0,1,yes,no,true,false
 
 TODO

Documentation/filesystems/vfs.txt

@@ -216,7 +216,6 @@ struct super_operations {
         void (*drop_inode) (struct inode *);
         void (*delete_inode) (struct inode *);
         void (*put_super) (struct super_block *);
-        void (*write_super) (struct super_block *);
         int (*sync_fs)(struct super_block *sb, int wait);
         int (*freeze_fs) (struct super_block *);
         int (*unfreeze_fs) (struct super_block *);
@@ -273,9 +272,6 @@ or bottom half).
   put_super: called when the VFS wishes to free the superblock
 	(i.e. unmount). This is called with the superblock lock held
 
-  write_super: called when the VFS superblock needs to be written to
-	disc. This method is optional
-
   sync_fs: called when VFS is writing out all dirty data associated with
   	a superblock. The second parameter indicates whether the method
 	should wait until the write out has been completed. Optional.

Documentation/laptops/laptop-mode.txt

@@ -262,9 +262,9 @@ MINIMUM_BATTERY_MINUTES=10
 
 #
 # Allowed dirty background ratio, in percent.  Once DIRTY_RATIO has been
-# exceeded, the kernel will wake pdflush which will then reduce the amount
-# of dirty memory to dirty_background_ratio.  Set this nice and low, so once
-# some writeout has commenced, we do a lot of it.
+# exceeded, the kernel will wake flusher threads which will then reduce the
+# amount of dirty memory to dirty_background_ratio.  Set this nice and low,
+# so once some writeout has commenced, we do a lot of it.
 #
 #DIRTY_BACKGROUND_RATIO=5
 
@@ -384,9 +384,9 @@ CPU_MAXFREQ=${CPU_MAXFREQ:-'slowest'}
 
 #
 # Allowed dirty background ratio, in percent.  Once DIRTY_RATIO has been
-# exceeded, the kernel will wake pdflush which will then reduce the amount
-# of dirty memory to dirty_background_ratio.  Set this nice and low, so once
-# some writeout has commenced, we do a lot of it.
+# exceeded, the kernel will wake flusher threads which will then reduce the
+# amount of dirty memory to dirty_background_ratio.  Set this nice and low,
+# so once some writeout has commenced, we do a lot of it.
 #
 DIRTY_BACKGROUND_RATIO=${DIRTY_BACKGROUND_RATIO:-'5'}
 

Documentation/networking/netconsole.txt

@@ -51,8 +51,23 @@ Built-in netconsole starts immediately after the TCP stack is
 initialized and attempts to bring up the supplied dev at the supplied
 address.
 
-The remote host can run either 'netcat -u -l -p <port>',
-'nc -l -u <port>' or syslogd.
+The remote host has several options to receive the kernel messages,
+for example:
+
+1) syslogd
+
+2) netcat
+
+   On distributions using a BSD-based netcat version (e.g. Fedora,
+   openSUSE and Ubuntu) the listening port must be specified without
+   the -p switch:
+
+   'nc -u -l -p <port>' / 'nc -u -l <port>' or
+   'netcat -u -l -p <port>' / 'netcat -u -l <port>'
+
+3) socat
+
+   'socat udp-recv:<port> -'
 
 Dynamic reconfiguration:
 ========================

Documentation/pinctrl.txt

@@ -840,9 +840,9 @@ static unsigned long i2c_pin_configs[] = {
 
 static struct pinctrl_map __initdata mapping[] = {
 	PIN_MAP_MUX_GROUP("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0", "i2c0"),
-	PIN_MAP_MUX_CONFIGS_GROUP("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0", i2c_grp_configs),
-	PIN_MAP_MUX_CONFIGS_PIN("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0scl", i2c_pin_configs),
-	PIN_MAP_MUX_CONFIGS_PIN("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0sda", i2c_pin_configs),
+	PIN_MAP_CONFIGS_GROUP("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0", i2c_grp_configs),
+	PIN_MAP_CONFIGS_PIN("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0scl", i2c_pin_configs),
+	PIN_MAP_CONFIGS_PIN("foo-i2c.0", PINCTRL_STATE_DEFAULT, "pinctrl-foo", "i2c0sda", i2c_pin_configs),
 };
 
 Finally, some devices expect the mapping table to contain certain specific

Documentation/security/Yama.txt

@@ -46,14 +46,13 @@ restrictions, it can call prctl(PR_SET_PTRACER, PR_SET_PTRACER_ANY, ...)
 so that any otherwise allowed process (even those in external pid namespaces)
 may attach.
 
-These restrictions do not change how ptrace via PTRACE_TRACEME operates.
-
-The sysctl settings are:
+The sysctl settings (writable only with CAP_SYS_PTRACE) are:
 
 0 - classic ptrace permissions: a process can PTRACE_ATTACH to any other
     process running under the same uid, as long as it is dumpable (i.e.
     did not transition uids, start privileged, or have called
-    prctl(PR_SET_DUMPABLE...) already).
+    prctl(PR_SET_DUMPABLE...) already). Similarly, PTRACE_TRACEME is
+    unchanged.
 
 1 - restricted ptrace: a process must have a predefined relationship
     with the inferior it wants to call PTRACE_ATTACH on. By default,
@@ -61,12 +60,13 @@ The sysctl settings are:
     classic criteria is also met. To change the relationship, an
     inferior can call prctl(PR_SET_PTRACER, debugger, ...) to declare
     an allowed debugger PID to call PTRACE_ATTACH on the inferior.
+    Using PTRACE_TRACEME is unchanged.
 
 2 - admin-only attach: only processes with CAP_SYS_PTRACE may use ptrace
-    with PTRACE_ATTACH.
+    with PTRACE_ATTACH, or through children calling PTRACE_TRACEME.
 
-3 - no attach: no processes may use ptrace with PTRACE_ATTACH. Once set,
-    this sysctl cannot be changed to a lower value.
+3 - no attach: no processes may use ptrace with PTRACE_ATTACH nor via
+    PTRACE_TRACEME. Once set, this sysctl value cannot be changed.
 
 The original children-only logic was based on the restrictions in grsecurity.
 

Documentation/sysctl/vm.txt

@@ -76,8 +76,8 @@ huge pages although processes will also directly compact memory as required.
 
 dirty_background_bytes
 
-Contains the amount of dirty memory at which the pdflush background writeback
-daemon will start writeback.
+Contains the amount of dirty memory at which the background kernel
+flusher threads will start writeback.
 
 Note: dirty_background_bytes is the counterpart of dirty_background_ratio. Only
 one of them may be specified at a time. When one sysctl is written it is
@@ -89,7 +89,7 @@ other appears as 0 when read.
 dirty_background_ratio
 
 Contains, as a percentage of total system memory, the number of pages at which
-the pdflush background writeback daemon will start writing out dirty data.
+the background kernel flusher threads will start writing out dirty data.
 
 ==============================================================
 
@@ -112,9 +112,9 @@ retained.
 dirty_expire_centisecs
 
 This tunable is used to define when dirty data is old enough to be eligible
-for writeout by the pdflush daemons.  It is expressed in 100'ths of a second.
-Data which has been dirty in-memory for longer than this interval will be
-written out next time a pdflush daemon wakes up.
+for writeout by the kernel flusher threads.  It is expressed in 100'ths
+of a second.  Data which has been dirty in-memory for longer than this
+interval will be written out next time a flusher thread wakes up.
 
 ==============================================================
 
@@ -128,7 +128,7 @@ data.
 
 dirty_writeback_centisecs
 
-The pdflush writeback daemons will periodically wake up and write `old' data
+The kernel flusher threads will periodically wake up and write `old' data
 out to disk.  This tunable expresses the interval between those wakeups, in
 100'ths of a second.
 

Documentation/vm/hugetlbpage.txt

@@ -299,11 +299,17 @@ map_hugetlb.c.
 *******************************************************************
 
 /*
- * hugepage-shm:  see Documentation/vm/hugepage-shm.c
+ * map_hugetlb: see tools/testing/selftests/vm/map_hugetlb.c
  */
 
 *******************************************************************
 
 /*
- * hugepage-mmap:  see Documentation/vm/hugepage-mmap.c
+ * hugepage-shm:  see tools/testing/selftests/vm/hugepage-shm.c
+ */
+
+*******************************************************************
+
+/*
+ * hugepage-mmap:  see tools/testing/selftests/vm/hugepage-mmap.c
  */

Documentation/w1/slaves/w1_therm

@@ -3,6 +3,7 @@ Kernel driver w1_therm
 
 Supported chips:
   * Maxim ds18*20 based temperature sensors.
+  * Maxim ds1825 based temperature sensors.
 
 Author: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
 
@@ -15,6 +16,7 @@ supported family codes:
 W1_THERM_DS18S20	0x10
 W1_THERM_DS1822		0x22
 W1_THERM_DS18B20	0x28
+W1_THERM_DS1825		0x3B
 
 Support is provided through the sysfs w1_slave file.  Each open and
 read sequence will initiate a temperature conversion then provide two

Documentation/watchdog/src/watchdog-test.c

@@ -31,7 +31,7 @@ static void keep_alive(void)
  * or "-e" to enable the card.
  */
 
-void term(int sig)
+static void term(int sig)
 {
     close(fd);
     fprintf(stderr, "Stopping watchdog ticks...\n");

MAINTAINERS

@@ -827,24 +827,24 @@ F:	arch/arm/mach-pxa/colibri-pxa270-income.c
 
 ARM/INTEL IOP32X ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
 ARM/INTEL IOP33X ARM ARCHITECTURE
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
 ARM/INTEL IOP13XX ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
 ARM/INTEL IQ81342EX MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
@@ -869,7 +869,7 @@ F:	drivers/pcmcia/pxa2xx_stargate2.c
 
 ARM/INTEL XSC3 (MANZANO) ARM CORE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 
@@ -925,14 +925,14 @@ S:	Maintained
 
 ARM/NOMADIK ARCHITECTURE
 M:	Alessandro Rubini <rubini@unipv.it>
-M:	Linus Walleij <linus.walleij@stericsson.com>
+M:	Linus Walleij <linus.walleij@linaro.org>
 M:	STEricsson <STEricsson_nomadik_linux@list.st.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-nomadik/
 F:	arch/arm/plat-nomadik/
 F:	drivers/i2c/busses/i2c-nomadik.c
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik.git
 
 ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
 M:	Nelson Castillo <arhuaco@freaks-unidos.net>
@@ -1146,7 +1146,7 @@ F:	drivers/usb/host/ehci-w90x900.c
 F:	drivers/video/nuc900fb.c
 
 ARM/U300 MACHINE SUPPORT
-M:	Linus Walleij <linus.walleij@stericsson.com>
+M:	Linus Walleij <linus.walleij@linaro.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	arch/arm/mach-u300/
@@ -1161,15 +1161,20 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git
 
 ARM/Ux500 ARM ARCHITECTURE
 M:	Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
-M:	Linus Walleij <linus.walleij@stericsson.com>
+M:	Linus Walleij <linus.walleij@linaro.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-ux500/
+F:	drivers/clocksource/clksrc-dbx500-prcmu.c
 F:	drivers/dma/ste_dma40*
+F:	drivers/hwspinlock/u8500_hsem.c
 F:	drivers/mfd/abx500*
 F:	drivers/mfd/ab8500*
-F:	drivers/mfd/stmpe*
+F:	drivers/mfd/dbx500*
+F:	drivers/mfd/db8500*
+F:	drivers/pinctrl/pinctrl-nomadik*
 F:	drivers/rtc/rtc-ab8500.c
+F:	drivers/rtc/rtc-pl031.c
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git
 
 ARM/VFP SUPPORT
@@ -1227,9 +1232,9 @@ S:	Maintained
 F:	drivers/hwmon/asb100.c
 
 ASYNCHRONOUS TRANSFERS/TRANSFORMS (IOAT) API
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 W:	http://sourceforge.net/projects/xscaleiop
-S:	Supported
+S:	Maintained
 F:	Documentation/crypto/async-tx-api.txt
 F:	crypto/async_tx/
 F:	drivers/dma/
@@ -2212,7 +2217,7 @@ S:	Maintained
 F:	drivers/scsi/tmscsim.*
 
 DC395x SCSI driver
-M:	Oliver Neukum <oliver@neukum.name>
+M:	Oliver Neukum <oliver@neukum.org>
 M:	Ali Akcaagac <aliakc@web.de>
 M:	Jamie Lenehan <lenehan@twibble.org>
 W:	http://twibble.org/dist/dc395x/
@@ -2359,7 +2364,7 @@ T:	git git://git.linaro.org/people/sumitsemwal/linux-dma-buf.git
 
 DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
 M:	Vinod Koul <vinod.koul@intel.com>
-M:	Dan Williams <dan.j.williams@intel.com>
+M:	Dan Williams <djbw@fb.com>
 S:	Supported
 F:	drivers/dma/
 F:	include/linux/dma*
@@ -3094,7 +3099,7 @@ F:	include/linux/gigaset_dev.h
 
 GPIO SUBSYSTEM
 M:	Grant Likely <grant.likely@secretlab.ca>
-M:	Linus Walleij <linus.walleij@stericsson.com>
+M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
 T:	git git://git.secretlab.ca/git/linux-2.6.git
 F:	Documentation/gpio.txt
@@ -3547,7 +3552,6 @@ K:	\b(ABS|SYN)_MT_
 
 INTEL C600 SERIES SAS CONTROLLER DRIVER
 M:	Intel SCU Linux support <intel-linux-scu@intel.com>
-M:	Dan Williams <dan.j.williams@intel.com>
 M:	Dave Jiang <dave.jiang@intel.com>
 M:	Ed Nadolski <edmund.nadolski@intel.com>
 L:	linux-scsi@vger.kernel.org
@@ -3590,8 +3594,8 @@ F:	arch/x86/kernel/microcode_core.c
 F:	arch/x86/kernel/microcode_intel.c
 
 INTEL I/OAT DMA DRIVER
-M:	Dan Williams <dan.j.williams@intel.com>
-S:	Supported
+M:	Dan Williams <djbw@fb.com>
+S:	Maintained
 F:	drivers/dma/ioat*
 
 INTEL IOMMU (VT-d)
@@ -3603,8 +3607,8 @@ F:	drivers/iommu/intel-iommu.c
 F:	include/linux/intel-iommu.h
 
 INTEL IOP-ADMA DMA DRIVER
-M:	Dan Williams <dan.j.williams@intel.com>
-S:	Maintained
+M:	Dan Williams <djbw@fb.com>
+S:	Odd fixes
 F:	drivers/dma/iop-adma.c
 
 INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT
@@ -4533,7 +4537,7 @@ S:	Supported
 F:	arch/microblaze/
 
 MICROTEK X6 SCANNER
-M:	Oliver Neukum <oliver@neukum.name>
+M:	Oliver Neukum <oliver@neukum.org>
 S:	Maintained
 F:	drivers/usb/image/microtek.*
 
@@ -5329,14 +5333,15 @@ PIN CONTROL SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
 F:	drivers/pinctrl/
+F:	include/linux/pinctrl/
 
 PIN CONTROLLER - ST SPEAR
-M:     Viresh Kumar <viresh.linux@gmail.com>
+M:	Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
 S:	Maintained
-F:	driver/pinctrl/spear/
+F:	drivers/pinctrl/spear/
 
 PKTCDVD DRIVER
 M:	Peter Osterlund <petero2@telia.com>
@@ -7071,7 +7076,7 @@ F:	include/linux/mtd/ubi.h
 F:	include/mtd/ubi-user.h
 
 USB ACM DRIVER
-M:	Oliver Neukum <oliver@neukum.name>
+M:	Oliver Neukum <oliver@neukum.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	Documentation/usb/acm.txt
@@ -7092,7 +7097,7 @@ S:	Supported
 F:	drivers/block/ub.c
 
 USB CDC ETHERNET DRIVER
-M:	Oliver Neukum <oliver@neukum.name>
+M:	Oliver Neukum <oliver@neukum.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/net/usb/cdc_*.c
@@ -7165,7 +7170,7 @@ F:	drivers/usb/host/isp116x*
 F:	include/linux/usb/isp116x.h
 
 USB KAWASAKI LSI DRIVER
-M:	Oliver Neukum <oliver@neukum.name>
+M:	Oliver Neukum <oliver@neukum.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/kl5kusb105.*
@@ -7283,6 +7288,12 @@ W:	http://www.connecttech.com
 S:	Supported
 F:	drivers/usb/serial/whiteheat*
 
+USB SMSC75XX ETHERNET DRIVER
+M:	Steve Glendinning <steve.glendinning@shawell.net>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/usb/smsc75xx.*
+
 USB SMSC95XX ETHERNET DRIVER
 M:	Steve Glendinning <steve.glendinning@shawell.net>
 L:	netdev@vger.kernel.org
@@ -7665,23 +7676,28 @@ S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	arch/arm/mach-s3c64xx/mach-crag6410*
 F:	drivers/clk/clk-wm83*.c
+F:	drivers/extcon/extcon-arizona.c
 F:	drivers/leds/leds-wm83*.c
 F:	drivers/gpio/gpio-*wm*.c
+F:	drivers/gpio/gpio-arizona.c
 F:	drivers/hwmon/wm83??-hwmon.c
 F:	drivers/input/misc/wm831x-on.c
 F:	drivers/input/touchscreen/wm831x-ts.c
 F:	drivers/input/touchscreen/wm97*.c
-F:	drivers/mfd/wm8*.c
+F:	drivers/mfd/arizona*
+F:	drivers/mfd/wm*.c
 F:	drivers/power/wm83*.c
 F:	drivers/rtc/rtc-wm83*.c
 F:	drivers/regulator/wm8*.c
 F:	drivers/video/backlight/wm83*_bl.c
 F:	drivers/watchdog/wm83*_wdt.c
+F:	include/linux/mfd/arizona/
 F:	include/linux/mfd/wm831x/
 F:	include/linux/mfd/wm8350/
 F:	include/linux/mfd/wm8400*
 F:	include/linux/wm97xx.h
 F:	include/sound/wm????.h
+F:	sound/soc/codecs/arizona.?
 F:	sound/soc/codecs/wm*
 
 WORKQUEUE

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 6
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc5
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

arch/alpha/Kconfig

@@ -18,6 +18,8 @@ config ALPHA
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG
 	select GENERIC_SMP_IDLE_THREAD
 	select GENERIC_CMOS_UPDATE
+	select GENERIC_STRNCPY_FROM_USER
+	select GENERIC_STRNLEN_USER
 	help
 	  The Alpha is a 64-bit general-purpose processor designed and
 	  marketed by the Digital Equipment Corporation of blessed memory,

arch/alpha/include/asm/atomic.h

@@ -14,8 +14,8 @@
  */
 
 
-#define ATOMIC_INIT(i)		( (atomic_t) { (i) } )
-#define ATOMIC64_INIT(i)	( (atomic64_t) { (i) } )
+#define ATOMIC_INIT(i)		{ (i) }
+#define ATOMIC64_INIT(i)	{ (i) }
 
 #define atomic_read(v)		(*(volatile int *)&(v)->counter)
 #define atomic64_read(v)	(*(volatile long *)&(v)->counter)

arch/alpha/include/asm/fpu.h

@@ -1,7 +1,9 @@
 #ifndef __ASM_ALPHA_FPU_H
 #define __ASM_ALPHA_FPU_H
 
+#ifdef __KERNEL__
 #include <asm/special_insns.h>
+#endif
 
 /*
  * Alpha floating-point control register defines:

arch/alpha/include/asm/ptrace.h

@@ -76,7 +76,10 @@ struct switch_stack {
 #define task_pt_regs(task) \
   ((struct pt_regs *) (task_stack_page(task) + 2*PAGE_SIZE) - 1)
 
-#define force_successful_syscall_return() (task_pt_regs(current)->r0 = 0)
+#define current_pt_regs() \
+  ((struct pt_regs *) ((char *)current_thread_info() + 2*PAGE_SIZE) - 1)
+
+#define force_successful_syscall_return() (current_pt_regs()->r0 = 0)
 
 #endif
 

arch/alpha/include/asm/socket.h

@@ -76,9 +76,11 @@
 /* Instruct lower device to use last 4-bytes of skb data as FCS */
 #define SO_NOFCS		43
 
+#ifdef __KERNEL__
 /* O_NONBLOCK clashes with the bits used for socket types.  Therefore we
  * have to define SOCK_NONBLOCK to a different value here.
  */
 #define SOCK_NONBLOCK	0x40000000
+#endif /* __KERNEL__ */
 
 #endif /* _ASM_SOCKET_H */

arch/alpha/include/asm/uaccess.h

@@ -433,36 +433,12 @@ clear_user(void __user *to, long len)
 #undef __module_address
 #undef __module_call
 
-/* Returns: -EFAULT if exception before terminator, N if the entire
-   buffer filled, else strlen.  */
+#define user_addr_max() \
+        (segment_eq(get_fs(), USER_DS) ? TASK_SIZE : ~0UL)
 
-extern long __strncpy_from_user(char *__to, const char __user *__from, long __to_len);
-
-extern inline long
-strncpy_from_user(char *to, const char __user *from, long n)
-{
-	long ret = -EFAULT;
-	if (__access_ok((unsigned long)from, 0, get_fs()))
-		ret = __strncpy_from_user(to, from, n);
-	return ret;
-}
-
-/* Returns: 0 if bad, string length+1 (memory size) of string if ok */
-extern long __strlen_user(const char __user *);
-
-extern inline long strlen_user(const char __user *str)
-{
-	return access_ok(VERIFY_READ,str,0) ? __strlen_user(str) : 0;
-}
-
-/* Returns: 0 if exception before NUL or reaching the supplied limit (N),
- * a value greater than N if the limit would be exceeded, else strlen.  */
-extern long __strnlen_user(const char __user *, long);
-
-extern inline long strnlen_user(const char __user *str, long n)
-{
-	return access_ok(VERIFY_READ,str,0) ? __strnlen_user(str, n) : 0;
-}
+extern long strncpy_from_user(char *dest, const char __user *src, long count);
+extern __must_check long strlen_user(const char __user *str);
+extern __must_check long strnlen_user(const char __user *str, long n);
 
 /*
  * About the exception table:

arch/alpha/include/asm/unistd.h

@@ -465,10 +465,12 @@
 #define __NR_setns			501
 #define __NR_accept4			502
 #define __NR_sendmmsg			503
+#define __NR_process_vm_readv		504
+#define __NR_process_vm_writev		505
 
 #ifdef __KERNEL__
 
-#define NR_SYSCALLS			504
+#define NR_SYSCALLS			506
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_STAT64

arch/alpha/include/asm/word-at-a-time.h

@@ -0,0 +1,55 @@
+#ifndef _ASM_WORD_AT_A_TIME_H
+#define _ASM_WORD_AT_A_TIME_H
+
+#include <asm/compiler.h>
+
+/*
+ * word-at-a-time interface for Alpha.
+ */
+
+/*
+ * We do not use the word_at_a_time struct on Alpha, but it needs to be
+ * implemented to humour the generic code.
+ */
+struct word_at_a_time {
+	const unsigned long unused;
+};
+
+#define WORD_AT_A_TIME_CONSTANTS { 0 }
+
+/* Return nonzero if val has a zero */
+static inline unsigned long has_zero(unsigned long val, unsigned long *bits, const struct word_at_a_time *c)
+{
+	unsigned long zero_locations = __kernel_cmpbge(0, val);
+	*bits = zero_locations;
+	return zero_locations;
+}
+
+static inline unsigned long prep_zero_mask(unsigned long val, unsigned long bits, const struct word_at_a_time *c)
+{
+	return bits;
+}
+
+#define create_zero_mask(bits) (bits)
+
+static inline unsigned long find_zero(unsigned long bits)
+{
+#if defined(CONFIG_ALPHA_EV6) && defined(CONFIG_ALPHA_EV67)
+	/* Simple if have CIX instructions */
+	return __kernel_cttz(bits);
+#else
+	unsigned long t1, t2, t3;
+	/* Retain lowest set bit only */
+	bits &= -bits;
+	/* Binary search for lowest set bit */
+	t1 = bits & 0xf0;
+	t2 = bits & 0xcc;
+	t3 = bits & 0xaa;
+	if (t1) t1 = 4;
+	if (t2) t2 = 2;
+	if (t3) t3 = 1;
+	return t1 + t2 + t3;
+#endif
+}
+
+#endif /* _ASM_WORD_AT_A_TIME_H */

arch/alpha/kernel/alpha_ksyms.c

@@ -52,7 +52,6 @@ EXPORT_SYMBOL(alpha_write_fp_reg_s);
 
 /* entry.S */
 EXPORT_SYMBOL(kernel_thread);
-EXPORT_SYMBOL(kernel_execve);
 
 /* Networking helper routines. */
 EXPORT_SYMBOL(csum_tcpudp_magic);
@@ -74,8 +73,6 @@ EXPORT_SYMBOL(alpha_fp_emul);
  */
 EXPORT_SYMBOL(__copy_user);
 EXPORT_SYMBOL(__do_clear_user);
-EXPORT_SYMBOL(__strncpy_from_user);
-EXPORT_SYMBOL(__strnlen_user);
 
 /* 
  * SMP-specific symbols.

arch/alpha/kernel/entry.S

@@ -663,58 +663,6 @@ kernel_thread:
 	br	ret_to_kernel
 .end kernel_thread
 
-/*
- * kernel_execve(path, argv, envp)
- */
-	.align	4
-	.globl	kernel_execve
-	.ent	kernel_execve
-kernel_execve:
-	/* We can be called from a module.  */
-	ldgp	$gp, 0($27)
-	lda	$sp, -(32+SIZEOF_PT_REGS+8)($sp)
-	.frame	$sp, 32+SIZEOF_PT_REGS+8, $26, 0
-	stq	$26, 0($sp)
-	stq	$16, 8($sp)
-	stq	$17, 16($sp)
-	stq	$18, 24($sp)
-	.prologue 1
-
-	lda	$16, 32($sp)
-	lda	$17, 0
-	lda	$18, SIZEOF_PT_REGS
-	bsr	$26, memset		!samegp
-
-	/* Avoid the HAE being gratuitously wrong, which would cause us
-	   to do the whole turn off interrupts thing and restore it.  */
-	ldq	$2, alpha_mv+HAE_CACHE
-	stq	$2, 152+32($sp)
-
-	ldq	$16, 8($sp)
-	ldq	$17, 16($sp)
-	ldq	$18, 24($sp)
-	lda	$19, 32($sp)
-	bsr	$26, do_execve		!samegp
-
-	ldq	$26, 0($sp)
-	bne	$0, 1f			/* error! */
-
-	/* Move the temporary pt_regs struct from its current location
-	   to the top of the kernel stack frame.  See copy_thread for
-	   details for a normal process.  */
-	lda	$16, 0x4000 - SIZEOF_PT_REGS($8)
-	lda	$17, 32($sp)
-	lda	$18, SIZEOF_PT_REGS
-	bsr	$26, memmove		!samegp
-
-	/* Take that over as our new stack frame and visit userland!  */
-	lda	$sp, 0x4000 - SIZEOF_PT_REGS($8)
-	br	$31, ret_from_sys_call
-
-1:	lda	$sp, 32+SIZEOF_PT_REGS+8($sp)
-	ret
-.end kernel_execve
-
 
 /*
  * Special system calls.  Most of these are special in that they either
@@ -796,115 +744,6 @@ sys_rt_sigreturn:
 	br	ret_from_sys_call
 .end sys_rt_sigreturn
 
-	.align	4
-	.globl	sys_sethae
-	.ent	sys_sethae
-sys_sethae:
-	.prologue 0
-	stq	$16, 152($sp)
-	ret
-.end sys_sethae
-
-	.align	4
-	.globl	osf_getpriority
-	.ent	osf_getpriority
-osf_getpriority:
-	lda	$sp, -16($sp)
-	stq	$26, 0($sp)
-	.prologue 0
-
-	jsr	$26, sys_getpriority
-
-	ldq	$26, 0($sp)
-	blt	$0, 1f
-
-	/* Return value is the unbiased priority, i.e. 20 - prio.
-	   This does result in negative return values, so signal
-	   no error by writing into the R0 slot.  */
-	lda	$1, 20
-	stq	$31, 16($sp)
-	subl	$1, $0, $0
-	unop
-
-1:	lda	$sp, 16($sp)
-	ret
-.end osf_getpriority
-
-	.align	4
-	.globl	sys_getxuid
-	.ent	sys_getxuid
-sys_getxuid:
-	.prologue 0
-	ldq	$2, TI_TASK($8)
-	ldq	$3, TASK_CRED($2)
-	ldl	$0, CRED_UID($3)
-	ldl	$1, CRED_EUID($3)
-	stq	$1, 80($sp)
-	ret
-.end sys_getxuid
-
-	.align	4
-	.globl	sys_getxgid
-	.ent	sys_getxgid
-sys_getxgid:
-	.prologue 0
-	ldq	$2, TI_TASK($8)
-	ldq	$3, TASK_CRED($2)
-	ldl	$0, CRED_GID($3)
-	ldl	$1, CRED_EGID($3)
-	stq	$1, 80($sp)
-	ret
-.end sys_getxgid
-
-	.align	4
-	.globl	sys_getxpid
-	.ent	sys_getxpid
-sys_getxpid:
-	.prologue 0
-	ldq	$2, TI_TASK($8)
-
-	/* See linux/kernel/timer.c sys_getppid for discussion
-	   about this loop.  */
-	ldq	$3, TASK_GROUP_LEADER($2)
-	ldq	$4, TASK_REAL_PARENT($3)
-	ldl	$0, TASK_TGID($2)
-1:	ldl	$1, TASK_TGID($4)
-#ifdef CONFIG_SMP
-	mov	$4, $5
-	mb
-	ldq	$3, TASK_GROUP_LEADER($2)
-	ldq	$4, TASK_REAL_PARENT($3)
-	cmpeq	$4, $5, $5
-	beq	$5, 1b
-#endif
-	stq	$1, 80($sp)
-	ret
-.end sys_getxpid
-
-	.align	4
-	.globl	sys_alpha_pipe
-	.ent	sys_alpha_pipe
-sys_alpha_pipe:
-	lda	$sp, -16($sp)
-	stq	$26, 0($sp)
-	.prologue 0
-
-	mov	$31, $17
-	lda	$16, 8($sp)
-	jsr	$26, do_pipe_flags
-
-	ldq	$26, 0($sp)
-	bne	$0, 1f
-
-	/* The return values are in $0 and $20.  */
-	ldl	$1, 12($sp)
-	ldl	$0, 8($sp)
-
-	stq	$1, 80+16($sp)
-1:	lda	$sp, 16($sp)
-	ret
-.end sys_alpha_pipe
-
 	.align	4
 	.globl	sys_execve
 	.ent	sys_execve

arch/alpha/kernel/osf_sys.c

@@ -1404,3 +1404,52 @@ SYSCALL_DEFINE3(osf_writev, unsigned long, fd,
 }
 
 #endif
+
+SYSCALL_DEFINE2(osf_getpriority, int, which, int, who)
+{
+	int prio = sys_getpriority(which, who);
+	if (prio >= 0) {
+		/* Return value is the unbiased priority, i.e. 20 - prio.
+		   This does result in negative return values, so signal
+		   no error */
+		force_successful_syscall_return();
+		prio = 20 - prio;
+	}
+	return prio;
+}
+
+SYSCALL_DEFINE0(getxuid)
+{
+	current_pt_regs()->r20 = sys_geteuid();
+	return sys_getuid();
+}
+
+SYSCALL_DEFINE0(getxgid)
+{
+	current_pt_regs()->r20 = sys_getegid();
+	return sys_getgid();
+}
+
+SYSCALL_DEFINE0(getxpid)
+{
+	current_pt_regs()->r20 = sys_getppid();
+	return sys_getpid();
+}
+
+SYSCALL_DEFINE0(alpha_pipe)
+{
+	int fd[2];
+	int res = do_pipe_flags(fd, 0);
+	if (!res) {
+		/* The return values are in $0 and $20.  */
+		current_pt_regs()->r20 = fd[1];
+		res = fd[0];
+	}
+	return res;
+}
+
+SYSCALL_DEFINE1(sethae, unsigned long, val)
+{
+	current_pt_regs()->hae = val;
+	return 0;
+}

arch/alpha/kernel/process.c

@@ -455,3 +455,22 @@ get_wchan(struct task_struct *p)
 	}
 	return pc;
 }
+
+int kernel_execve(const char *path, const char *const argv[], const char *const envp[])
+{
+	/* Avoid the HAE being gratuitously wrong, which would cause us
+	   to do the whole turn off interrupts thing and restore it.  */
+	struct pt_regs regs = {.hae = alpha_mv.hae_cache};
+	int err = do_execve(path, argv, envp, &regs);
+	if (!err) {
+		struct pt_regs *p = current_pt_regs();
+		/* copy regs to normal position and off to userland we go... */
+		*p = regs;
+		__asm__ __volatile__ (
+			"mov	%0, $sp;"
+			"br	$31, ret_from_sys_call"
+			: : "r"(p));
+	}
+	return err;
+}
+EXPORT_SYMBOL(kernel_execve);

arch/alpha/kernel/systbls.S

@@ -111,7 +111,7 @@ sys_call_table:
 	.quad sys_socket
 	.quad sys_connect
 	.quad sys_accept
-	.quad osf_getpriority			/* 100 */
+	.quad sys_osf_getpriority			/* 100 */
 	.quad sys_send
 	.quad sys_recv
 	.quad sys_sigreturn
@@ -522,6 +522,8 @@ sys_call_table:
 	.quad sys_setns
 	.quad sys_accept4
 	.quad sys_sendmmsg
+	.quad sys_process_vm_readv
+	.quad sys_process_vm_writev		/* 505 */
 
 	.size sys_call_table, . - sys_call_table
 	.type sys_call_table, @object

arch/alpha/lib/Makefile

@@ -31,8 +31,6 @@ lib-y =	__divqu.o __remqu.o __divlu.o __remlu.o \
 	$(ev6-y)memchr.o \
 	$(ev6-y)copy_user.o \
 	$(ev6-y)clear_user.o \
-	$(ev6-y)strncpy_from_user.o \
-	$(ev67-y)strlen_user.o \
 	$(ev6-y)csum_ipv6_magic.o \
 	$(ev6-y)clear_page.o \
 	$(ev6-y)copy_page.o \

arch/alpha/lib/ev6-strncpy_from_user.S

@@ -1,424 +0,0 @@
-/*
- * arch/alpha/lib/ev6-strncpy_from_user.S
- * 21264 version contributed by Rick Gorton <rick.gorton@alpha-processor.com>
- *
- * Just like strncpy except in the return value:
- *
- * -EFAULT       if an exception occurs before the terminator is copied.
- * N             if the buffer filled.
- *
- * Otherwise the length of the string is returned.
- *
- * Much of the information about 21264 scheduling/coding comes from:
- *	Compiler Writer's Guide for the Alpha 21264
- *	abbreviated as 'CWG' in other comments here
- *	ftp.digital.com/pub/Digital/info/semiconductor/literature/dsc-library.html
- * Scheduling notation:
- *	E	- either cluster
- *	U	- upper subcluster; U0 - subcluster U0; U1 - subcluster U1
- *	L	- lower subcluster; L0 - subcluster L0; L1 - subcluster L1
- * A bunch of instructions got moved and temp registers were changed
- * to aid in scheduling.  Control flow was also re-arranged to eliminate
- * branches, and to provide longer code sequences to enable better scheduling.
- * A total rewrite (using byte load/stores for start & tail sequences)
- * is desirable, but very difficult to do without a from-scratch rewrite.
- * Save that for the future.
- */
-
-
-#include <asm/errno.h>
-#include <asm/regdef.h>
-
-
-/* Allow an exception for an insn; exit if we get one.  */
-#define EX(x,y...)			\
-	99: x,##y;			\
-	.section __ex_table,"a";	\
-	.long 99b - .;			\
-	lda $31, $exception-99b($0); 	\
-	.previous
-
-
-	.set noat
-	.set noreorder
-	.text
-
-	.globl __strncpy_from_user
-	.ent __strncpy_from_user
-	.frame $30, 0, $26
-	.prologue 0
-
-	.align 4
-__strncpy_from_user:
-	and	a0, 7, t3	# E : find dest misalignment
-	beq	a2, $zerolength	# U :
-
-	/* Are source and destination co-aligned?  */
-	mov	a0, v0		# E : save the string start
-	xor	a0, a1, t4	# E :
-	EX( ldq_u t1, 0(a1) )	# L : Latency=3 load first quadword
-	ldq_u	t0, 0(a0)	# L : load first (partial) aligned dest quadword
-
-	addq	a2, t3, a2	# E : bias count by dest misalignment
-	subq	a2, 1, a3	# E :
-	addq	zero, 1, t10	# E :
-	and	t4, 7, t4	# E : misalignment between the two
-
-	and	a3, 7, t6	# E : number of tail bytes
-	sll	t10, t6, t10	# E : t10 = bitmask of last count byte
-	bne	t4, $unaligned	# U :
-	lda	t2, -1		# E : build a mask against false zero
-
-	/*
-	 * We are co-aligned; take care of a partial first word.
-	 * On entry to this basic block:
-	 * t0 == the first destination word for masking back in
-	 * t1 == the first source word.
-	 */
-
-	srl	a3, 3, a2	# E : a2 = loop counter = (count - 1)/8
-	addq	a1, 8, a1	# E :
-	mskqh	t2, a1, t2	# U :   detection in the src word
-	nop
-
-	/* Create the 1st output word and detect 0's in the 1st input word.  */
-	mskqh	t1, a1, t3	# U :
-	mskql	t0, a1, t0	# U : assemble the first output word
-	ornot	t1, t2, t2	# E :
-	nop
-
-	cmpbge	zero, t2, t8	# E : bits set iff null found
-	or	t0, t3, t0	# E :
-	beq	a2, $a_eoc	# U :
-	bne	t8, $a_eos	# U : 2nd branch in a quad.  Bad.
-
-	/* On entry to this basic block:
-	 * t0 == a source quad not containing a null.
-	 * a0 - current aligned destination address
-	 * a1 - current aligned source address
-	 * a2 - count of quadwords to move.
-	 * NOTE: Loop improvement - unrolling this is going to be
-	 *	a huge win, since we're going to stall otherwise.
-	 *	Fix this later.  For _really_ large copies, look
-	 *	at using wh64 on a look-ahead basis.  See the code
-	 *	in clear_user.S and copy_user.S.
-	 * Presumably, since (a0) and (a1) do not overlap (by C definition)
-	 * Lots of nops here:
-	 *	- Separate loads from stores
-	 *	- Keep it to 1 branch/quadpack so the branch predictor
-	 *	  can train.
-	 */
-$a_loop:
-	stq_u	t0, 0(a0)	# L :
-	addq	a0, 8, a0	# E :
-	nop
-	subq	a2, 1, a2	# E :
-
-	EX( ldq_u t0, 0(a1) )	# L :
-	addq	a1, 8, a1	# E :
-	cmpbge	zero, t0, t8	# E : Stall 2 cycles on t0
-	beq	a2, $a_eoc      # U :
-
-	beq	t8, $a_loop	# U :
-	nop
-	nop
-	nop
-
-	/* Take care of the final (partial) word store.  At this point
-	 * the end-of-count bit is set in t8 iff it applies.
-	 *
-	 * On entry to this basic block we have:
-	 * t0 == the source word containing the null
-	 * t8 == the cmpbge mask that found it.
-	 */
-$a_eos:
-	negq	t8, t12		# E : find low bit set
-	and	t8, t12, t12	# E : 
-
-	/* We're doing a partial word store and so need to combine
-	   our source and original destination words.  */
-	ldq_u	t1, 0(a0)	# L :
-	subq	t12, 1, t6	# E :
-
-	or	t12, t6, t8	# E :
-	zapnot	t0, t8, t0	# U : clear src bytes > null
-	zap	t1, t8, t1	# U : clear dst bytes <= null
-	or	t0, t1, t0	# E :
-
-	stq_u	t0, 0(a0)	# L :
-	br	$finish_up	# L0 :
-	nop
-	nop
-
-	/* Add the end-of-count bit to the eos detection bitmask.  */
-	.align 4
-$a_eoc:
-	or	t10, t8, t8
-	br	$a_eos
-	nop
-	nop
-
-
-/* The source and destination are not co-aligned.  Align the destination
-   and cope.  We have to be very careful about not reading too much and
-   causing a SEGV.  */
-
-	.align 4
-$u_head:
-	/* We know just enough now to be able to assemble the first
-	   full source word.  We can still find a zero at the end of it
-	   that prevents us from outputting the whole thing.
-
-	   On entry to this basic block:
-	   t0 == the first dest word, unmasked
-	   t1 == the shifted low bits of the first source word
-	   t6 == bytemask that is -1 in dest word bytes */
-
-	EX( ldq_u t2, 8(a1) )	# L : load second src word
-	addq	a1, 8, a1	# E :
-	mskql	t0, a0, t0	# U : mask trailing garbage in dst
-	extqh	t2, a1, t4	# U :
-
-	or	t1, t4, t1	# E : first aligned src word complete
-	mskqh	t1, a0, t1	# U : mask leading garbage in src
-	or	t0, t1, t0	# E : first output word complete
-	or	t0, t6, t6	# E : mask original data for zero test
-
-	cmpbge	zero, t6, t8	# E :
-	beq	a2, $u_eocfin	# U :
-	bne	t8, $u_final	# U : bad news - 2nd branch in a quad
-	lda	t6, -1		# E : mask out the bits we have
-
-	mskql	t6, a1, t6	# U :   already seen
-	stq_u	t0, 0(a0)	# L : store first output word
-	or      t6, t2, t2	# E :
-	cmpbge	zero, t2, t8	# E : find nulls in second partial
-
-	addq	a0, 8, a0		# E :
-	subq	a2, 1, a2		# E :
-	bne	t8, $u_late_head_exit	# U :
-	nop
-
-	/* Finally, we've got all the stupid leading edge cases taken care
-	   of and we can set up to enter the main loop.  */
-
-	extql	t2, a1, t1	# U : position hi-bits of lo word
-	EX( ldq_u t2, 8(a1) )	# L : read next high-order source word
-	addq	a1, 8, a1	# E :
-	cmpbge	zero, t2, t8	# E :
-
-	beq	a2, $u_eoc	# U :
-	bne	t8, $u_eos	# U :
-	nop
-	nop
-
-	/* Unaligned copy main loop.  In order to avoid reading too much,
-	   the loop is structured to detect zeros in aligned source words.
-	   This has, unfortunately, effectively pulled half of a loop
-	   iteration out into the head and half into the tail, but it does
-	   prevent nastiness from accumulating in the very thing we want
-	   to run as fast as possible.
-
-	   On entry to this basic block:
-	   t1 == the shifted high-order bits from the previous source word
-	   t2 == the unshifted current source word
-
-	   We further know that t2 does not contain a null terminator.  */
-
-	/*
-	 * Extra nops here:
-	 *	separate load quads from store quads
-	 *	only one branch/quad to permit predictor training
-	 */
-
-	.align 4
-$u_loop:
-	extqh	t2, a1, t0	# U : extract high bits for current word
-	addq	a1, 8, a1	# E :
-	extql	t2, a1, t3	# U : extract low bits for next time
-	addq	a0, 8, a0	# E :
-
-	or	t0, t1, t0	# E : current dst word now complete
-	EX( ldq_u t2, 0(a1) )	# L : load high word for next time
-	subq	a2, 1, a2	# E :
-	nop
-
-	stq_u	t0, -8(a0)	# L : save the current word
-	mov	t3, t1		# E :
-	cmpbge	zero, t2, t8	# E : test new word for eos
-	beq	a2, $u_eoc	# U :
-
-	beq	t8, $u_loop	# U :
-	nop
-	nop
-	nop
-
-	/* We've found a zero somewhere in the source word we just read.
-	   If it resides in the lower half, we have one (probably partial)
-	   word to write out, and if it resides in the upper half, we
-	   have one full and one partial word left to write out.
-
-	   On entry to this basic block:
-	   t1 == the shifted high-order bits from the previous source word
-	   t2 == the unshifted current source word.  */
-	.align 4
-$u_eos:
-	extqh	t2, a1, t0	# U :
-	or	t0, t1, t0	# E : first (partial) source word complete
-	cmpbge	zero, t0, t8	# E : is the null in this first bit?
-	nop
-
-	bne	t8, $u_final	# U :
-	stq_u	t0, 0(a0)	# L : the null was in the high-order bits
-	addq	a0, 8, a0	# E :
-	subq	a2, 1, a2	# E :
-
-	.align 4
-$u_late_head_exit:
-	extql	t2, a1, t0	# U :
-	cmpbge	zero, t0, t8	# E :
-	or	t8, t10, t6	# E :
-	cmoveq	a2, t6, t8	# E :
-
-	/* Take care of a final (probably partial) result word.
-	   On entry to this basic block:
-	   t0 == assembled source word
-	   t8 == cmpbge mask that found the null.  */
-	.align 4
-$u_final:
-	negq	t8, t6		# E : isolate low bit set
-	and	t6, t8, t12	# E :
-	ldq_u	t1, 0(a0)	# L :
-	subq	t12, 1, t6	# E :
-
-	or	t6, t12, t8	# E :
-	zapnot	t0, t8, t0	# U : kill source bytes > null
-	zap	t1, t8, t1	# U : kill dest bytes <= null
-	or	t0, t1, t0	# E :
-
-	stq_u	t0, 0(a0)	# E :
-	br	$finish_up	# U :
-	nop
-	nop
-
-	.align 4
-$u_eoc:				# end-of-count
-	extqh	t2, a1, t0	# U :
-	or	t0, t1, t0	# E :
-	cmpbge	zero, t0, t8	# E :
-	nop
-
-	.align 4
-$u_eocfin:			# end-of-count, final word
-	or	t10, t8, t8	# E :
-	br	$u_final	# U :
-	nop
-	nop
-
-	/* Unaligned copy entry point.  */
-	.align 4
-$unaligned:
-
-	srl	a3, 3, a2	# U : a2 = loop counter = (count - 1)/8
-	and	a0, 7, t4	# E : find dest misalignment
-	and	a1, 7, t5	# E : find src misalignment
-	mov	zero, t0	# E :
-
-	/* Conditionally load the first destination word and a bytemask
-	   with 0xff indicating that the destination byte is sacrosanct.  */
-
-	mov	zero, t6	# E :
-	beq	t4, 1f		# U :
-	ldq_u	t0, 0(a0)	# L :
-	lda	t6, -1		# E :
-
-	mskql	t6, a0, t6	# E :
-	nop
-	nop
-	nop
-
-	.align 4
-1:
-	subq	a1, t4, a1	# E : sub dest misalignment from src addr
-	/* If source misalignment is larger than dest misalignment, we need
-	   extra startup checks to avoid SEGV.  */
-	cmplt	t4, t5, t12	# E :
-	extql	t1, a1, t1	# U : shift src into place
-	lda	t2, -1		# E : for creating masks later
-
-	beq	t12, $u_head	# U :
-	mskqh	t2, t5, t2	# U : begin src byte validity mask
-	cmpbge	zero, t1, t8	# E : is there a zero?
-	nop
-
-	extql	t2, a1, t2	# U :
-	or	t8, t10, t5	# E : test for end-of-count too
-	cmpbge	zero, t2, t3	# E :
-	cmoveq	a2, t5, t8	# E : Latency=2, extra map slot
-
-	nop			# E : goes with cmov
-	andnot	t8, t3, t8	# E :
-	beq	t8, $u_head	# U :
-	nop
-
-	/* At this point we've found a zero in the first partial word of
-	   the source.  We need to isolate the valid source data and mask
-	   it into the original destination data.  (Incidentally, we know
-	   that we'll need at least one byte of that original dest word.) */
-
-	ldq_u	t0, 0(a0)	# L :
-	negq	t8, t6		# E : build bitmask of bytes <= zero
-	mskqh	t1, t4, t1	# U :
-	and	t6, t8, t12	# E :
-
-	subq	t12, 1, t6	# E :
-	or	t6, t12, t8	# E :
-	zapnot	t2, t8, t2	# U : prepare source word; mirror changes
-	zapnot	t1, t8, t1	# U : to source validity mask
-
-	andnot	t0, t2, t0	# E : zero place for source to reside
-	or	t0, t1, t0	# E : and put it there
-	stq_u	t0, 0(a0)	# L :
-	nop
-
-	.align 4
-$finish_up:
-	zapnot	t0, t12, t4	# U : was last byte written null?
-	and	t12, 0xf0, t3	# E : binary search for the address of the
-	cmovne	t4, 1, t4	# E : Latency=2, extra map slot
-	nop			# E : with cmovne
-
-	and	t12, 0xcc, t2	# E : last byte written
-	and	t12, 0xaa, t1	# E :
-	cmovne	t3, 4, t3	# E : Latency=2, extra map slot
-	nop			# E : with cmovne
-
-	bic	a0, 7, t0
-	cmovne	t2, 2, t2	# E : Latency=2, extra map slot
-	nop			# E : with cmovne
-	nop
-
-	cmovne	t1, 1, t1	# E : Latency=2, extra map slot
-	nop			# E : with cmovne
-	addq	t0, t3, t0	# E :
-	addq	t1, t2, t1	# E :
-
-	addq	t0, t1, t0	# E :
-	addq	t0, t4, t0	# add one if we filled the buffer
-	subq	t0, v0, v0	# find string length
-	ret			# L0 :
-
-	.align 4
-$zerolength:
-	nop
-	nop
-	nop
-	clr	v0
-
-$exception:
-	nop
-	nop
-	nop
-	ret
-
-	.end __strncpy_from_user

arch/alpha/lib/ev67-strlen_user.S

@@ -1,107 +0,0 @@
-/*
- * arch/alpha/lib/ev67-strlen_user.S
- * 21264 version contributed by Rick Gorton <rick.gorton@api-networks.com>
- *
- * Return the length of the string including the NULL terminator
- * (strlen+1) or zero if an error occurred.
- *
- * In places where it is critical to limit the processing time,
- * and the data is not trusted, strnlen_user() should be used.
- * It will return a value greater than its second argument if
- * that limit would be exceeded. This implementation is allowed
- * to access memory beyond the limit, but will not cross a page
- * boundary when doing so.
- *
- * Much of the information about 21264 scheduling/coding comes from:
- *      Compiler Writer's Guide for the Alpha 21264
- *      abbreviated as 'CWG' in other comments here
- *      ftp.digital.com/pub/Digital/info/semiconductor/literature/dsc-library.html
- * Scheduling notation:
- *      E       - either cluster
- *      U       - upper subcluster; U0 - subcluster U0; U1 - subcluster U1
- *      L       - lower subcluster; L0 - subcluster L0; L1 - subcluster L1
- * Try not to change the actual algorithm if possible for consistency.
- */
-
-#include <asm/regdef.h>
-
-
-/* Allow an exception for an insn; exit if we get one.  */
-#define EX(x,y...)			\
-	99: x,##y;			\
-	.section __ex_table,"a";	\
-	.long 99b - .;			\
-	lda v0, $exception-99b(zero);	\
-	.previous
-
-
-	.set noreorder
-	.set noat
-	.text
-
-	.globl __strlen_user
-	.ent __strlen_user
-	.frame sp, 0, ra
-
-	.align 4
-__strlen_user:
-	ldah	a1, 32767(zero)	# do not use plain strlen_user() for strings
-				# that might be almost 2 GB long; you should
-				# be using strnlen_user() instead
-	nop
-	nop
-	nop
-
-	.globl __strnlen_user
-
-	.align 4
-__strnlen_user:
-	.prologue 0
-	EX( ldq_u t0, 0(a0) )	# L : load first quadword (a0 may be misaligned)
-	lda     t1, -1(zero)	# E :
-
-	insqh   t1, a0, t1	# U :
-	andnot  a0, 7, v0	# E :
-	or      t1, t0, t0	# E :
-	subq	a0, 1, a0	# E : get our +1 for the return 
-
-	cmpbge  zero, t0, t1	# E : t1 <- bitmask: bit i == 1 <==> i-th byte == 0
-	subq	a1, 7, t2	# E :
-	subq	a0, v0, t0	# E :
-	bne     t1, $found	# U :
-
-	addq	t2, t0, t2	# E :
-	addq	a1, 1, a1	# E :
-	nop			# E :
-	nop			# E :
-
-	.align 4
-$loop:	ble	t2, $limit	# U :
-	EX( ldq t0, 8(v0) )	# L :
-	nop			# E :
-	nop			# E :
-
-	cmpbge  zero, t0, t1	# E :
-	subq	t2, 8, t2	# E :
-	addq    v0, 8, v0	# E : addr += 8
-	beq     t1, $loop	# U :
-
-$found: cttz	t1, t2		# U0 :
-	addq	v0, t2, v0	# E :
-	subq    v0, a0, v0	# E :
-	ret			# L0 :
-
-$exception:
-	nop
-	nop
-	nop
-	ret
-
-	.align 4		# currently redundant
-$limit:
-	nop
-	nop
-	subq	a1, t2, v0
-	ret
-
-	.end __strlen_user

arch/alpha/lib/strlen_user.S

@@ -1,91 +0,0 @@
-/*
- * arch/alpha/lib/strlen_user.S
- *
- * Return the length of the string including the NUL terminator
- * (strlen+1) or zero if an error occurred.
- *
- * In places where it is critical to limit the processing time,
- * and the data is not trusted, strnlen_user() should be used.
- * It will return a value greater than its second argument if
- * that limit would be exceeded. This implementation is allowed
- * to access memory beyond the limit, but will not cross a page
- * boundary when doing so.
- */
-
-#include <asm/regdef.h>
-
-
-/* Allow an exception for an insn; exit if we get one.  */
-#define EX(x,y...)			\
-	99: x,##y;			\
-	.section __ex_table,"a";	\
-	.long 99b - .;			\
-	lda v0, $exception-99b(zero);	\
-	.previous
-
-
-	.set noreorder
-	.set noat
-	.text
-
-	.globl __strlen_user
-	.ent __strlen_user
-	.frame sp, 0, ra
-
-	.align 3
-__strlen_user:
-	ldah	a1, 32767(zero)	# do not use plain strlen_user() for strings
-				# that might be almost 2 GB long; you should
-				# be using strnlen_user() instead
-
-	.globl __strnlen_user
-
-	.align 3
-__strnlen_user:
-	.prologue 0
-
-	EX( ldq_u t0, 0(a0) )	# load first quadword (a0 may be misaligned)
-	lda     t1, -1(zero)
-	insqh   t1, a0, t1
-	andnot  a0, 7, v0
-	or      t1, t0, t0
-	subq	a0, 1, a0	# get our +1 for the return 
-	cmpbge  zero, t0, t1	# t1 <- bitmask: bit i == 1 <==> i-th byte == 0
-	subq	a1, 7, t2
-	subq	a0, v0, t0
-	bne     t1, $found
-
-	addq	t2, t0, t2
-	addq	a1, 1, a1
-
-	.align 3
-$loop:	ble	t2, $limit
-	EX( ldq t0, 8(v0) )
-	subq	t2, 8, t2
-	addq    v0, 8, v0	# addr += 8
-	cmpbge  zero, t0, t1
-	beq     t1, $loop
-
-$found:	negq    t1, t2		# clear all but least set bit
-	and     t1, t2, t1
-
-	and     t1, 0xf0, t2	# binary search for that set bit
-	and	t1, 0xcc, t3
-	and	t1, 0xaa, t4
-	cmovne	t2, 4, t2
-	cmovne	t3, 2, t3
-	cmovne	t4, 1, t4
-	addq	t2, t3, t2
-	addq	v0, t4, v0
-	addq	v0, t2, v0
-	nop			# dual issue next two on ev4 and ev5
-	subq    v0, a0, v0
-$exception:
-	ret
-
-	.align 3		# currently redundant
-$limit:
-	subq	a1, t2, v0
-	ret
-
-	.end __strlen_user

arch/alpha/lib/strncpy_from_user.S

@@ -1,339 +0,0 @@
-/*
- * arch/alpha/lib/strncpy_from_user.S
- * Contributed by Richard Henderson (rth@tamu.edu)
- *
- * Just like strncpy except in the return value:
- *
- * -EFAULT       if an exception occurs before the terminator is copied.
- * N             if the buffer filled.
- *
- * Otherwise the length of the string is returned.
- */
-
-
-#include <asm/errno.h>
-#include <asm/regdef.h>
-
-
-/* Allow an exception for an insn; exit if we get one.  */
-#define EX(x,y...)			\
-	99: x,##y;			\
-	.section __ex_table,"a";	\
-	.long 99b - .;			\
-	lda $31, $exception-99b($0); 	\
-	.previous
-
-
-	.set noat
-	.set noreorder
-	.text
-
-	.globl __strncpy_from_user
-	.ent __strncpy_from_user
-	.frame $30, 0, $26
-	.prologue 0
-
-	.align 3
-$aligned:
-	/* On entry to this basic block:
-	   t0 == the first destination word for masking back in
-	   t1 == the first source word.  */
-
-	/* Create the 1st output word and detect 0's in the 1st input word.  */
-	lda	t2, -1		# e1    : build a mask against false zero
-	mskqh	t2, a1, t2	# e0    :   detection in the src word
-	mskqh	t1, a1, t3	# e0    :
-	ornot	t1, t2, t2	# .. e1 :
-	mskql	t0, a1, t0	# e0    : assemble the first output word
-	cmpbge	zero, t2, t8	# .. e1 : bits set iff null found
-	or	t0, t3, t0	# e0    :
-	beq	a2, $a_eoc	# .. e1 :
-	bne	t8, $a_eos	# .. e1 :
-
-	/* On entry to this basic block:
-	   t0 == a source word not containing a null.  */
-
-$a_loop:
-	stq_u	t0, 0(a0)	# e0    :
-	addq	a0, 8, a0	# .. e1 :
-	EX( ldq_u t0, 0(a1) )	# e0    :
-	addq	a1, 8, a1	# .. e1 :
-	subq	a2, 1, a2	# e0    :
-	cmpbge	zero, t0, t8	# .. e1 (stall)
-	beq	a2, $a_eoc      # e1    :
-	beq	t8, $a_loop	# e1    :
-
-	/* Take care of the final (partial) word store.  At this point
-	   the end-of-count bit is set in t8 iff it applies.
-
-	   On entry to this basic block we have:
-	   t0 == the source word containing the null
-	   t8 == the cmpbge mask that found it.  */
-
-$a_eos:
-	negq	t8, t12		# e0    : find low bit set
-	and	t8, t12, t12	# e1 (stall)
-
-	/* For the sake of the cache, don't read a destination word
-	   if we're not going to need it.  */
-	and	t12, 0x80, t6	# e0    :
-	bne	t6, 1f		# .. e1 (zdb)
-
-	/* We're doing a partial word store and so need to combine
-	   our source and original destination words.  */
-	ldq_u	t1, 0(a0)	# e0    :
-	subq	t12, 1, t6	# .. e1 :
-	or	t12, t6, t8	# e0    :
-	unop			#
-	zapnot	t0, t8, t0	# e0    : clear src bytes > null
-	zap	t1, t8, t1	# .. e1 : clear dst bytes <= null
-	or	t0, t1, t0	# e1    :
-
-1:	stq_u	t0, 0(a0)
-	br	$finish_up
-
-	/* Add the end-of-count bit to the eos detection bitmask.  */
-$a_eoc:
-	or	t10, t8, t8
-	br	$a_eos
-
-	/*** The Function Entry Point ***/
-	.align 3
-__strncpy_from_user:
-	mov	a0, v0		# save the string start
-	beq	a2, $zerolength
-
-	/* Are source and destination co-aligned?  */
-	xor	a0, a1, t1	# e0    :
-	and	a0, 7, t0	# .. e1 : find dest misalignment
-	and	t1, 7, t1	# e0    :
-	addq	a2, t0, a2	# .. e1 : bias count by dest misalignment
-	subq	a2, 1, a2	# e0    :
-	and	a2, 7, t2	# e1    :
-	srl	a2, 3, a2	# e0    : a2 = loop counter = (count - 1)/8
-	addq	zero, 1, t10	# .. e1 :
-	sll	t10, t2, t10	# e0    : t10 = bitmask of last count byte
-	bne	t1, $unaligned	# .. e1 :
-
-	/* We are co-aligned; take care of a partial first word.  */
-
-	EX( ldq_u t1, 0(a1) )	# e0    : load first src word
-	addq	a1, 8, a1	# .. e1 :
-
-	beq	t0, $aligned	# avoid loading dest word if not needed
-	ldq_u	t0, 0(a0)	# e0    :
-	br	$aligned	# .. e1 :
-
-
-/* The source and destination are not co-aligned.  Align the destination
-   and cope.  We have to be very careful about not reading too much and
-   causing a SEGV.  */
-
-	.align 3
-$u_head:
-	/* We know just enough now to be able to assemble the first
-	   full source word.  We can still find a zero at the end of it
-	   that prevents us from outputting the whole thing.
-
-	   On entry to this basic block:
-	   t0 == the first dest word, unmasked
-	   t1 == the shifted low bits of the first source word
-	   t6 == bytemask that is -1 in dest word bytes */
-
-	EX( ldq_u t2, 8(a1) )	# e0    : load second src word
-	addq	a1, 8, a1	# .. e1 :
-	mskql	t0, a0, t0	# e0    : mask trailing garbage in dst
-	extqh	t2, a1, t4	# e0    :
-	or	t1, t4, t1	# e1    : first aligned src word complete
-	mskqh	t1, a0, t1	# e0    : mask leading garbage in src
-	or	t0, t1, t0	# e0    : first output word complete
-	or	t0, t6, t6	# e1    : mask original data for zero test
-	cmpbge	zero, t6, t8	# e0    :
-	beq	a2, $u_eocfin	# .. e1 :
-	bne	t8, $u_final	# e1    :
-
-	lda	t6, -1			# e1    : mask out the bits we have
-	mskql	t6, a1, t6		# e0    :   already seen
-	stq_u	t0, 0(a0)		# e0    : store first output word
-	or      t6, t2, t2		# .. e1 :
-	cmpbge	zero, t2, t8		# e0    : find nulls in second partial
-	addq	a0, 8, a0		# .. e1 :
-	subq	a2, 1, a2		# e0    :
-	bne	t8, $u_late_head_exit	# .. e1 :
-
-	/* Finally, we've got all the stupid leading edge cases taken care
-	   of and we can set up to enter the main loop.  */
-
-	extql	t2, a1, t1	# e0    : position hi-bits of lo word
-	EX( ldq_u t2, 8(a1) )	# .. e1 : read next high-order source word
-	addq	a1, 8, a1	# e0    :
-	cmpbge	zero, t2, t8	# e1 (stall)
-	beq	a2, $u_eoc	# e1    :
-	bne	t8, $u_eos	# e1    :
-
-	/* Unaligned copy main loop.  In order to avoid reading too much,
-	   the loop is structured to detect zeros in aligned source words.
-	   This has, unfortunately, effectively pulled half of a loop
-	   iteration out into the head and half into the tail, but it does
-	   prevent nastiness from accumulating in the very thing we want
-	   to run as fast as possible.
-
-	   On entry to this basic block:
-	   t1 == the shifted high-order bits from the previous source word
-	   t2 == the unshifted current source word
-
-	   We further know that t2 does not contain a null terminator.  */
-
-	.align 3
-$u_loop:
-	extqh	t2, a1, t0	# e0    : extract high bits for current word
-	addq	a1, 8, a1	# .. e1 :
-	extql	t2, a1, t3	# e0    : extract low bits for next time
-	addq	a0, 8, a0	# .. e1 :
-	or	t0, t1, t0	# e0    : current dst word now complete
-	EX( ldq_u t2, 0(a1) )	# .. e1 : load high word for next time
-	stq_u	t0, -8(a0)	# e0    : save the current word
-	mov	t3, t1		# .. e1 :
-	subq	a2, 1, a2	# e0    :
-	cmpbge	zero, t2, t8	# .. e1 : test new word for eos
-	beq	a2, $u_eoc	# e1    :
-	beq	t8, $u_loop	# e1    :
-
-	/* We've found a zero somewhere in the source word we just read.
-	   If it resides in the lower half, we have one (probably partial)
-	   word to write out, and if it resides in the upper half, we
-	   have one full and one partial word left to write out.
-
-	   On entry to this basic block:
-	   t1 == the shifted high-order bits from the previous source word
-	   t2 == the unshifted current source word.  */
-$u_eos:
-	extqh	t2, a1, t0	# e0    :
-	or	t0, t1, t0	# e1    : first (partial) source word complete
-
-	cmpbge	zero, t0, t8	# e0    : is the null in this first bit?
-	bne	t8, $u_final	# .. e1 (zdb)
-
-	stq_u	t0, 0(a0)	# e0    : the null was in the high-order bits
-	addq	a0, 8, a0	# .. e1 :
-	subq	a2, 1, a2	# e1    :
-
-$u_late_head_exit:
-	extql	t2, a1, t0	# .. e0 :
-	cmpbge	zero, t0, t8	# e0    :
-	or	t8, t10, t6	# e1    :
-	cmoveq	a2, t6, t8	# e0    :
-	nop			# .. e1 :
-
-	/* Take care of a final (probably partial) result word.
-	   On entry to this basic block:
-	   t0 == assembled source word
-	   t8 == cmpbge mask that found the null.  */
-$u_final:
-	negq	t8, t6		# e0    : isolate low bit set
-	and	t6, t8, t12	# e1    :
-
-	and	t12, 0x80, t6	# e0    : avoid dest word load if we can
-	bne	t6, 1f		# .. e1 (zdb)
-
-	ldq_u	t1, 0(a0)	# e0    :
-	subq	t12, 1, t6	# .. e1 :
-	or	t6, t12, t8	# e0    :
-	zapnot	t0, t8, t0	# .. e1 : kill source bytes > null
-	zap	t1, t8, t1	# e0    : kill dest bytes <= null
-	or	t0, t1, t0	# e1    :
-
-1:	stq_u	t0, 0(a0)	# e0    :
-	br	$finish_up
-
-$u_eoc:				# end-of-count
-	extqh	t2, a1, t0
-	or	t0, t1, t0
-	cmpbge	zero, t0, t8
-
-$u_eocfin:			# end-of-count, final word
-	or	t10, t8, t8
-	br	$u_final
-
-	/* Unaligned copy entry point.  */
-	.align 3
-$unaligned:
-
-	EX( ldq_u t1, 0(a1) )	# e0    : load first source word
-
-	and	a0, 7, t4	# .. e1 : find dest misalignment
-	and	a1, 7, t5	# e0    : find src misalignment
-
-	/* Conditionally load the first destination word and a bytemask
-	   with 0xff indicating that the destination byte is sacrosanct.  */
-
-	mov	zero, t0	# .. e1 :
-	mov	zero, t6	# e0    :
-	beq	t4, 1f		# .. e1 :
-	ldq_u	t0, 0(a0)	# e0    :
-	lda	t6, -1		# .. e1 :
-	mskql	t6, a0, t6	# e0    :
-1:
-	subq	a1, t4, a1	# .. e1 : sub dest misalignment from src addr
-
-	/* If source misalignment is larger than dest misalignment, we need
-	   extra startup checks to avoid SEGV.  */
-
-	cmplt	t4, t5, t12	# e1    :
-	extql	t1, a1, t1	# .. e0 : shift src into place
-	lda	t2, -1		# e0    : for creating masks later
-	beq	t12, $u_head	# e1    :
-
-	mskqh	t2, t5, t2	# e0    : begin src byte validity mask
-	cmpbge	zero, t1, t8	# .. e1 : is there a zero?
-	extql	t2, a1, t2	# e0    :
-	or	t8, t10, t5	# .. e1 : test for end-of-count too
-	cmpbge	zero, t2, t3	# e0    :
-	cmoveq	a2, t5, t8	# .. e1 :
-	andnot	t8, t3, t8	# e0    :
-	beq	t8, $u_head	# .. e1 (zdb)
-
-	/* At this point we've found a zero in the first partial word of
-	   the source.  We need to isolate the valid source data and mask
-	   it into the original destination data.  (Incidentally, we know
-	   that we'll need at least one byte of that original dest word.) */
-
-	ldq_u	t0, 0(a0)	# e0    :
-	negq	t8, t6		# .. e1 : build bitmask of bytes <= zero
-	mskqh	t1, t4, t1	# e0    :
-	and	t6, t8, t12	# .. e1 :
-	subq	t12, 1, t6	# e0    :
-	or	t6, t12, t8	# e1    :
-
-	zapnot	t2, t8, t2	# e0    : prepare source word; mirror changes
-	zapnot	t1, t8, t1	# .. e1 : to source validity mask
-
-	andnot	t0, t2, t0	# e0    : zero place for source to reside
-	or	t0, t1, t0	# e1    : and put it there
-	stq_u	t0, 0(a0)	# e0    :
-
-$finish_up:
-	zapnot	t0, t12, t4	# was last byte written null?
-	cmovne	t4, 1, t4
-
-	and	t12, 0xf0, t3	# binary search for the address of the
-	and	t12, 0xcc, t2	# last byte written
-	and	t12, 0xaa, t1
-	bic	a0, 7, t0
-	cmovne	t3, 4, t3
-	cmovne	t2, 2, t2
-	cmovne	t1, 1, t1
-	addq	t0, t3, t0
-	addq	t1, t2, t1
-	addq	t0, t1, t0
-	addq	t0, t4, t0	# add one if we filled the buffer
-
-	subq	t0, v0, v0	# find string length
-	ret
-
-$zerolength:
-	clr	v0
-$exception:
-	ret
-
-	.end __strncpy_from_user

arch/alpha/mm/fault.c

@@ -89,6 +89,8 @@ do_page_fault(unsigned long address, unsigned long mmcsr,
 	const struct exception_table_entry *fixup;
 	int fault, si_code = SEGV_MAPERR;
 	siginfo_t info;
+	unsigned int flags = (FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE |
+			      (cause > 0 ? FAULT_FLAG_WRITE : 0));
 
 	/* As of EV6, a load into $31/$f31 is a prefetch, and never faults
 	   (or is suppressed by the PALcode).  Support that for older CPUs
@@ -114,6 +116,7 @@ do_page_fault(unsigned long address, unsigned long mmcsr,
 		goto vmalloc_fault;
 #endif
 
+retry:
 	down_read(&mm->mmap_sem);
 	vma = find_vma(mm, address);
 	if (!vma)
@@ -144,8 +147,11 @@ do_page_fault(unsigned long address, unsigned long mmcsr,
 	/* If for any reason at all we couldn't handle the fault,
 	   make sure we exit gracefully rather than endlessly redo
 	   the fault.  */
-	fault = handle_mm_fault(mm, vma, address, cause > 0 ? FAULT_FLAG_WRITE : 0);
-	up_read(&mm->mmap_sem);
+	fault = handle_mm_fault(mm, vma, address, flags);
+
+	if ((fault & VM_FAULT_RETRY) && fatal_signal_pending(current))
+		return;
+
 	if (unlikely(fault & VM_FAULT_ERROR)) {
 		if (fault & VM_FAULT_OOM)
 			goto out_of_memory;
@@ -153,10 +159,26 @@ do_page_fault(unsigned long address, unsigned long mmcsr,
 			goto do_sigbus;
 		BUG();
 	}
-	if (fault & VM_FAULT_MAJOR)
-		current->maj_flt++;
-	else
-		current->min_flt++;
+
+	if (flags & FAULT_FLAG_ALLOW_RETRY) {
+		if (fault & VM_FAULT_MAJOR)
+			current->maj_flt++;
+		else
+			current->min_flt++;
+		if (fault & VM_FAULT_RETRY) {
+			flags &= ~FAULT_FLAG_ALLOW_RETRY;
+
+			 /* No need to up_read(&mm->mmap_sem) as we would
+			 * have already released it in __lock_page_or_retry
+			 * in mm/filemap.c.
+			 */
+
+			goto retry;
+		}
+	}
+
+	up_read(&mm->mmap_sem);
+
 	return;
 
 	/* Something tried to access memory that isn't in our memory map.
@@ -186,12 +208,14 @@ do_page_fault(unsigned long address, unsigned long mmcsr,
 	/* We ran out of memory, or some other thing happened to us that
 	   made us unable to handle the page fault gracefully.  */
  out_of_memory:
+	up_read(&mm->mmap_sem);
 	if (!user_mode(regs))
 		goto no_context;
 	pagefault_out_of_memory();
 	return;
 
  do_sigbus:
+	up_read(&mm->mmap_sem);
 	/* Send a sigbus, regardless of whether we were in kernel
 	   or user mode.  */
 	info.si_signo = SIGBUS;

arch/alpha/oprofile/common.c

@@ -12,6 +12,7 @@
 #include <linux/smp.h>
 #include <linux/errno.h>
 #include <asm/ptrace.h>
+#include <asm/special_insns.h>
 
 #include "op_impl.h"
 

arch/arm/Kconfig

@@ -6,7 +6,7 @@ config ARM
 	select HAVE_DMA_API_DEBUG
 	select HAVE_IDE if PCI || ISA || PCMCIA
 	select HAVE_DMA_ATTRS
-	select HAVE_DMA_CONTIGUOUS if (CPU_V6 || CPU_V6K || CPU_V7)
+	select HAVE_DMA_CONTIGUOUS if MMU
 	select HAVE_MEMBLOCK
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
@@ -38,7 +38,6 @@ config ARM
 	select HARDIRQS_SW_RESEND
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW
-	select GENERIC_IRQ_PROBE
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select HARDIRQS_SW_RESEND
 	select CPU_PM if (SUSPEND || CPU_IDLE)
@@ -126,11 +125,6 @@ config TRACE_IRQFLAGS_SUPPORT
 	bool
 	default y
 
-config GENERIC_LOCKBREAK
-	bool
-	default y
-	depends on SMP && PREEMPT
-
 config RWSEM_GENERIC_SPINLOCK
 	bool
 	default y
@@ -2150,6 +2144,7 @@ source "drivers/cpufreq/Kconfig"
 config CPU_FREQ_IMX
 	tristate "CPUfreq driver for i.MX CPUs"
 	depends on ARCH_MXC && CPU_FREQ
+	select CPU_FREQ_TABLE
 	help
 	  This enables the CPUfreq driver for i.MX CPUs.
 

arch/arm/boot/dts/am33xx.dtsi

@@ -154,5 +154,10 @@
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
 		};
+
+		wdt2: wdt@44e35000 {
+			compatible = "ti,omap3-wdt";
+			ti,hwmods = "wd_timer2";
+		};
 	};
 };

arch/arm/boot/dts/at91sam9g25ek.dts

@@ -15,7 +15,7 @@
 	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
 	};
 
 	ahb {

arch/arm/boot/dts/imx23.dtsi

@@ -51,11 +51,11 @@
 
 			dma-apbh@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
-				reg = <0x80004000 2000>;
+				reg = <0x80004000 0x2000>;
 			};
 
 			ecc@80008000 {
-				reg = <0x80008000 2000>;
+				reg = <0x80008000 0x2000>;
 				status = "disabled";
 			};
 
@@ -63,7 +63,7 @@
 				compatible = "fsl,imx23-gpmi-nand";
 				#address-cells = <1>;
 				#size-cells = <1>;
-				reg = <0x8000c000 2000>, <0x8000a000 2000>;
+				reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>;
 				reg-names = "gpmi-nand", "bch";
 				interrupts = <13>, <56>;
 				interrupt-names = "gpmi-dma", "bch";
@@ -72,14 +72,14 @@
 			};
 
 			ssp0: ssp@80010000 {
-				reg = <0x80010000 2000>;
+				reg = <0x80010000 0x2000>;
 				interrupts = <15 14>;
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
 
 			etm@80014000 {
-				reg = <0x80014000 2000>;
+				reg = <0x80014000 0x2000>;
 				status = "disabled";
 			};
 
@@ -87,7 +87,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx23-pinctrl", "simple-bus";
-				reg = <0x80018000 2000>;
+				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
 					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
@@ -273,32 +273,32 @@
 			};
 
 			emi@80020000 {
-				reg = <0x80020000 2000>;
+				reg = <0x80020000 0x2000>;
 				status = "disabled";
 			};
 
 			dma-apbx@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
-				reg = <0x80024000 2000>;
+				reg = <0x80024000 0x2000>;
 			};
 
 			dcp@80028000 {
-				reg = <0x80028000 2000>;
+				reg = <0x80028000 0x2000>;
 				status = "disabled";
 			};
 
 			pxp@8002a000 {
-				reg = <0x8002a000 2000>;
+				reg = <0x8002a000 0x2000>;
 				status = "disabled";
 			};
 
 			ocotp@8002c000 {
-				reg = <0x8002c000 2000>;
+				reg = <0x8002c000 0x2000>;
 				status = "disabled";
 			};
 
 			axi-ahb@8002e000 {
-				reg = <0x8002e000 2000>;
+				reg = <0x8002e000 0x2000>;
 				status = "disabled";
 			};
 
@@ -310,14 +310,14 @@
 			};
 
 			ssp1: ssp@80034000 {
-				reg = <0x80034000 2000>;
+				reg = <0x80034000 0x2000>;
 				interrupts = <2 20>;
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
 
 			tvenc@80038000 {
-				reg = <0x80038000 2000>;
+				reg = <0x80038000 0x2000>;
 				status = "disabled";
 			};
                 };
@@ -330,37 +330,37 @@
 			ranges;
 
 			clkctl@80040000 {
-				reg = <0x80040000 2000>;
+				reg = <0x80040000 0x2000>;
 				status = "disabled";
 			};
 
 			saif0: saif@80042000 {
-				reg = <0x80042000 2000>;
+				reg = <0x80042000 0x2000>;
 				status = "disabled";
 			};
 
 			power@80044000 {
-				reg = <0x80044000 2000>;
+				reg = <0x80044000 0x2000>;
 				status = "disabled";
 			};
 
 			saif1: saif@80046000 {
-				reg = <0x80046000 2000>;
+				reg = <0x80046000 0x2000>;
 				status = "disabled";
 			};
 
 			audio-out@80048000 {
-				reg = <0x80048000 2000>;
+				reg = <0x80048000 0x2000>;
 				status = "disabled";
 			};
 
 			audio-in@8004c000 {
-				reg = <0x8004c000 2000>;
+				reg = <0x8004c000 0x2000>;
 				status = "disabled";
 			};
 
 			lradc@80050000 {
-				reg = <0x80050000 2000>;
+				reg = <0x80050000 0x2000>;
 				status = "disabled";
 			};
 
@@ -370,26 +370,26 @@
 			};
 
 			i2c@80058000 {
-				reg = <0x80058000 2000>;
+				reg = <0x80058000 0x2000>;
 				status = "disabled";
 			};
 
 			rtc@8005c000 {
 				compatible = "fsl,imx23-rtc", "fsl,stmp3xxx-rtc";
-				reg = <0x8005c000 2000>;
+				reg = <0x8005c000 0x2000>;
 				interrupts = <22>;
 			};
 
 			pwm: pwm@80064000 {
 				compatible = "fsl,imx23-pwm";
-				reg = <0x80064000 2000>;
+				reg = <0x80064000 0x2000>;
 				#pwm-cells = <2>;
 				fsl,pwm-number = <5>;
 				status = "disabled";
 			};
 
 			timrot@80068000 {
-				reg = <0x80068000 2000>;
+				reg = <0x80068000 0x2000>;
 				status = "disabled";
 			};
 
@@ -429,7 +429,7 @@
 		ranges;
 
 		usbctrl@80080000 {
-			reg = <0x80080000 0x10000>;
+			reg = <0x80080000 0x40000>;
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/imx27-3ds.dts

@@ -27,7 +27,7 @@
 				status = "okay";
 			};
 
-			uart@1000a000 {
+			uart1: serial@1000a000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};

arch/arm/boot/dts/imx27.dtsi

@@ -19,6 +19,12 @@
 		serial3 = &uart4;
 		serial4 = &uart5;
 		serial5 = &uart6;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		gpio5 = &gpio6;
 	};
 
 	avic: avic-interrupt-controller@e0000000 {

arch/arm/boot/dts/imx28.dtsi

@@ -57,18 +57,18 @@
 			};
 
 			hsadc@80002000 {
-				reg = <0x80002000 2000>;
+				reg = <0x80002000 0x2000>;
 				interrupts = <13 87>;
 				status = "disabled";
 			};
 
 			dma-apbh@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
-				reg = <0x80004000 2000>;
+				reg = <0x80004000 0x2000>;
 			};
 
 			perfmon@80006000 {
-				reg = <0x80006000 800>;
+				reg = <0x80006000 0x800>;
 				interrupts = <27>;
 				status = "disabled";
 			};
@@ -77,7 +77,7 @@
 				compatible = "fsl,imx28-gpmi-nand";
 				#address-cells = <1>;
 				#size-cells = <1>;
-				reg = <0x8000c000 2000>, <0x8000a000 2000>;
+				reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>;
 				reg-names = "gpmi-nand", "bch";
 				interrupts = <88>, <41>;
 				interrupt-names = "gpmi-dma", "bch";
@@ -86,28 +86,28 @@
 			};
 
 			ssp0: ssp@80010000 {
-				reg = <0x80010000 2000>;
+				reg = <0x80010000 0x2000>;
 				interrupts = <96 82>;
 				fsl,ssp-dma-channel = <0>;
 				status = "disabled";
 			};
 
 			ssp1: ssp@80012000 {
-				reg = <0x80012000 2000>;
+				reg = <0x80012000 0x2000>;
 				interrupts = <97 83>;
 				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
 
 			ssp2: ssp@80014000 {
-				reg = <0x80014000 2000>;
+				reg = <0x80014000 0x2000>;
 				interrupts = <98 84>;
 				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
 
 			ssp3: ssp@80016000 {
-				reg = <0x80016000 2000>;
+				reg = <0x80016000 0x2000>;
 				interrupts = <99 85>;
 				fsl,ssp-dma-channel = <3>;
 				status = "disabled";
@@ -117,7 +117,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx28-pinctrl", "simple-bus";
-				reg = <0x80018000 2000>;
+				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
 					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
@@ -510,96 +510,96 @@
 			};
 
 			digctl@8001c000 {
-				reg = <0x8001c000 2000>;
+				reg = <0x8001c000 0x2000>;
 				interrupts = <89>;
 				status = "disabled";
 			};
 
 			etm@80022000 {
-				reg = <0x80022000 2000>;
+				reg = <0x80022000 0x2000>;
 				status = "disabled";
 			};
 
 			dma-apbx@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
-				reg = <0x80024000 2000>;
+				reg = <0x80024000 0x2000>;
 			};
 
 			dcp@80028000 {
-				reg = <0x80028000 2000>;
+				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
 				status = "disabled";
 			};
 
 			pxp@8002a000 {
-				reg = <0x8002a000 2000>;
+				reg = <0x8002a000 0x2000>;
 				interrupts = <39>;
 				status = "disabled";
 			};
 
 			ocotp@8002c000 {
-				reg = <0x8002c000 2000>;
+				reg = <0x8002c000 0x2000>;
 				status = "disabled";
 			};
 
 			axi-ahb@8002e000 {
-				reg = <0x8002e000 2000>;
+				reg = <0x8002e000 0x2000>;
 				status = "disabled";
 			};
 
 			lcdif@80030000 {
 				compatible = "fsl,imx28-lcdif";
-				reg = <0x80030000 2000>;
+				reg = <0x80030000 0x2000>;
 				interrupts = <38 86>;
 				status = "disabled";
 			};
 
 			can0: can@80032000 {
 				compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
-				reg = <0x80032000 2000>;
+				reg = <0x80032000 0x2000>;
 				interrupts = <8>;
 				status = "disabled";
 			};
 
 			can1: can@80034000 {
 				compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
-				reg = <0x80034000 2000>;
+				reg = <0x80034000 0x2000>;
 				interrupts = <9>;
 				status = "disabled";
 			};
 
 			simdbg@8003c000 {
-				reg = <0x8003c000 200>;
+				reg = <0x8003c000 0x200>;
 				status = "disabled";
 			};
 
 			simgpmisel@8003c200 {
-				reg = <0x8003c200 100>;
+				reg = <0x8003c200 0x100>;
 				status = "disabled";
 			};
 
 			simsspsel@8003c300 {
-				reg = <0x8003c300 100>;
+				reg = <0x8003c300 0x100>;
 				status = "disabled";
 			};
 
 			simmemsel@8003c400 {
-				reg = <0x8003c400 100>;
+				reg = <0x8003c400 0x100>;
 				status = "disabled";
 			};
 
 			gpiomon@8003c500 {
-				reg = <0x8003c500 100>;
+				reg = <0x8003c500 0x100>;
 				status = "disabled";
 			};
 
 			simenet@8003c700 {
-				reg = <0x8003c700 100>;
+				reg = <0x8003c700 0x100>;
 				status = "disabled";
 			};
 
 			armjtag@8003c800 {
-				reg = <0x8003c800 100>;
+				reg = <0x8003c800 0x100>;
 				status = "disabled";
 			};
                 };
@@ -612,45 +612,45 @@
 			ranges;
 
 			clkctl@80040000 {
-				reg = <0x80040000 2000>;
+				reg = <0x80040000 0x2000>;
 				status = "disabled";
 			};
 
 			saif0: saif@80042000 {
 				compatible = "fsl,imx28-saif";
-				reg = <0x80042000 2000>;
+				reg = <0x80042000 0x2000>;
 				interrupts = <59 80>;
 				fsl,saif-dma-channel = <4>;
 				status = "disabled";
 			};
 
 			power@80044000 {
-				reg = <0x80044000 2000>;
+				reg = <0x80044000 0x2000>;
 				status = "disabled";
 			};
 
 			saif1: saif@80046000 {
 				compatible = "fsl,imx28-saif";
-				reg = <0x80046000 2000>;
+				reg = <0x80046000 0x2000>;
 				interrupts = <58 81>;
 				fsl,saif-dma-channel = <5>;
 				status = "disabled";
 			};
 
 			lradc@80050000 {
-				reg = <0x80050000 2000>;
+				reg = <0x80050000 0x2000>;
 				status = "disabled";
 			};
 
 			spdif@80054000 {
-				reg = <0x80054000 2000>;
+				reg = <0x80054000 0x2000>;
 				interrupts = <45 66>;
 				status = "disabled";
 			};
 
 			rtc@80056000 {
 				compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc";
-				reg = <0x80056000 2000>;
+				reg = <0x80056000 0x2000>;
 				interrupts = <29>;
 			};
 
@@ -658,7 +658,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx28-i2c";
-				reg = <0x80058000 2000>;
+				reg = <0x80058000 0x2000>;
 				interrupts = <111 68>;
 				clock-frequency = <100000>;
 				status = "disabled";
@@ -668,7 +668,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx28-i2c";
-				reg = <0x8005a000 2000>;
+				reg = <0x8005a000 0x2000>;
 				interrupts = <110 69>;
 				clock-frequency = <100000>;
 				status = "disabled";
@@ -676,14 +676,14 @@
 
 			pwm: pwm@80064000 {
 				compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
-				reg = <0x80064000 2000>;
+				reg = <0x80064000 0x2000>;
 				#pwm-cells = <2>;
 				fsl,pwm-number = <8>;
 				status = "disabled";
 			};
 
 			timrot@80068000 {
-				reg = <0x80068000 2000>;
+				reg = <0x80068000 0x2000>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/imx51-babbage.dts

@@ -25,8 +25,8 @@
 		aips@70000000 { /* aips-1 */
 			spba@70000000 {
 				esdhc@70004000 { /* ESDHC1 */
-					fsl,cd-internal;
-					fsl,wp-internal;
+					fsl,cd-controller;
+					fsl,wp-controller;
 					status = "okay";
 				};
 
@@ -53,7 +53,7 @@
 						spi-max-frequency = <6000000>;
 						reg = <0>;
 						interrupt-parent = <&gpio1>;
-						interrupts = <8>;
+						interrupts = <8 0x4>;
 
 						regulators {
 							sw1_reg: sw1 {

arch/arm/boot/dts/imx51.dtsi

@@ -17,6 +17,10 @@
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
 	};
 
 	tzic: tz-interrupt-controller@e0000000 {

arch/arm/boot/dts/imx53-ard.dts

@@ -64,12 +64,32 @@
 			reg = <0xf4000000 0x2000000>;
 			phy-mode = "mii";
 			interrupt-parent = <&gpio2>;
-			interrupts = <31>;
+			interrupts = <31 0x8>;
 			reg-io-width = <4>;
+			/*
+			 * VDD33A and VDDVARIO of LAN9220 are supplied by
+			 * SW4_3V3 of LTC3589.  Before the regulator driver
+			 * for this PMIC is available, we use a fixed dummy
+			 * 3V3 regulator to get LAN9220 driver probing work.
+			 */
+			vdd33a-supply = <&reg_3p3v>;
+			vddvario-supply = <&reg_3p3v>;
 			smsc,irq-push-pull;
 		};
 	};
 
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 

arch/arm/boot/dts/imx53.dtsi

@@ -19,6 +19,13 @@
 		serial2 = &uart3;
 		serial3 = &uart4;
 		serial4 = &uart5;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		gpio5 = &gpio6;
+		gpio6 = &gpio7;
 	};
 
 	tzic: tz-interrupt-controller@0fffc000 {

arch/arm/boot/dts/imx6q-sabrelite.dts

@@ -53,6 +53,7 @@
 						fsl,pins = <
 							   144  0x80000000	/* MX6Q_PAD_EIM_D22__GPIO_3_22 */
 							   121  0x80000000	/* MX6Q_PAD_EIM_D19__GPIO_3_19 */
+							   953  0x80000000	/* MX6Q_PAD_GPIO_0__CCM_CLKO */
 							   >;
 					};
 				};

arch/arm/boot/dts/imx6q.dtsi

@@ -19,6 +19,13 @@
 		serial2 = &uart3;
 		serial3 = &uart4;
 		serial4 = &uart5;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		gpio5 = &gpio6;
+		gpio6 = &gpio7;
 	};
 
 	cpus {

arch/arm/boot/dts/kirkwood-iconnect.dts

@@ -41,9 +41,13 @@
 		};
 		power-blue {
 			label = "power:blue";
-			gpios = <&gpio1 11 0>;
+			gpios = <&gpio1 10 0>;
 			linux,default-trigger = "timer";
 		};
+		power-red {
+			label = "power:red";
+			gpios = <&gpio1 11 0>;
+		};
 		usb1 {
 			label = "usb1:blue";
 			gpios = <&gpio1 12 0>;

arch/arm/boot/dts/twl6030.dtsi

@@ -66,6 +66,7 @@
 
 	vcxio: regulator@8 {
 		compatible = "ti,twl6030-vcxio";
+		regulator-always-on;
 	};
 
 	vusb: regulator@9 {
@@ -74,10 +75,12 @@
 
 	v1v8: regulator@10 {
 		compatible = "ti,twl6030-v1v8";
+		regulator-always-on;
 	};
 
 	v2v1: regulator@11 {
 		compatible = "ti,twl6030-v2v1";
+		regulator-always-on;
 	};
 
 	clk32kg: regulator@12 {

arch/arm/configs/armadillo800eva_defconfig

@@ -33,7 +33,7 @@ CONFIG_AEABI=y
 CONFIG_FORCE_MAX_ZONEORDER=13
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
+CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096 rw"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
 CONFIG_VFP=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -192,6 +192,7 @@ CONFIG_RTC_DRV_MC13XXX=y
 CONFIG_RTC_DRV_MXC=y
 CONFIG_DMADEVICES=y
 CONFIG_IMX_SDMA=y
+CONFIG_MXS_DMA=y
 CONFIG_COMMON_CLK_DEBUG=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT2_FS=y

arch/arm/configs/mxs_defconfig

@@ -34,7 +34,6 @@ CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_AEABI=y
-CONFIG_DEFAULT_MMAP_MIN_ADDR=65536
 CONFIG_AUTO_ZRELADDR=y
 CONFIG_FPE_NWFPE=y
 CONFIG_NET=y

arch/arm/configs/tct_hammer_defconfig

@@ -7,7 +7,7 @@ CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_BUG is not set
+# CONFIG_BUGVERBOSE is not set
 # CONFIG_ELF_CORE is not set
 # CONFIG_SHMEM is not set
 CONFIG_SLOB=y

arch/arm/configs/u8500_defconfig

@@ -86,6 +86,7 @@ CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_LP5521=y
+CONFIG_LEDS_GPIO=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AB8500=y
 CONFIG_RTC_DRV_PL031=y

arch/arm/include/asm/dma-mapping.h

@@ -202,6 +202,13 @@ static inline void dma_free_writecombine(struct device *dev, size_t size,
 	return dma_free_attrs(dev, size, cpu_addr, dma_handle, &attrs);
 }
 
+/*
+ * This can be called during early boot to increase the size of the atomic
+ * coherent DMA pool above the default value of 256KiB. It must be called
+ * before postcore_initcall.
+ */
+extern void __init init_dma_coherent_pool_size(unsigned long size);
+
 /*
  * This can be called during boot to increase the size of the consistent
  * DMA region above it's default value of 2MB. It must be called before the

arch/arm/include/asm/pgtable.h

@@ -195,25 +195,6 @@ static inline pte_t *pmd_page_vaddr(pmd_t pmd)
 
 #define pte_clear(mm,addr,ptep)	set_pte_ext(ptep, __pte(0), 0)
 
-#if __LINUX_ARM_ARCH__ < 6
-static inline void __sync_icache_dcache(pte_t pteval)
-{
-}
-#else
-extern void __sync_icache_dcache(pte_t pteval);
-#endif
-
-static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
-			      pte_t *ptep, pte_t pteval)
-{
-	if (addr >= TASK_SIZE)
-		set_pte_ext(ptep, pteval, 0);
-	else {
-		__sync_icache_dcache(pteval);
-		set_pte_ext(ptep, pteval, PTE_EXT_NG);
-	}
-}
-
 #define pte_none(pte)		(!pte_val(pte))
 #define pte_present(pte)	(pte_val(pte) & L_PTE_PRESENT)
 #define pte_write(pte)		(!(pte_val(pte) & L_PTE_RDONLY))
@@ -226,6 +207,27 @@ static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
 	((pte_val(pte) & (L_PTE_PRESENT | L_PTE_USER)) == \
 	 (L_PTE_PRESENT | L_PTE_USER))
 
+#if __LINUX_ARM_ARCH__ < 6
+static inline void __sync_icache_dcache(pte_t pteval)
+{
+}
+#else
+extern void __sync_icache_dcache(pte_t pteval);
+#endif
+
+static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
+			      pte_t *ptep, pte_t pteval)
+{
+	unsigned long ext = 0;
+
+	if (addr < TASK_SIZE && pte_present_user(pteval)) {
+		__sync_icache_dcache(pteval);
+		ext |= PTE_EXT_NG;
+	}
+
+	set_pte_ext(ptep, pteval, ext);
+}
+
 #define PTE_BIT_FUNC(fn,op) \
 static inline pte_t pte_##fn(pte_t pte) { pte_val(pte) op; return pte; }
 
@@ -251,13 +253,13 @@ static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
  *
  *   3 3 2 2 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1 1 1
  *   1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
- *   <--------------- offset --------------------> <- type --> 0 0 0
+ *   <--------------- offset ----------------------> < type -> 0 0 0
  *
- * This gives us up to 63 swap files and 32GB per swap file.  Note that
+ * This gives us up to 31 swap files and 64GB per swap file.  Note that
  * the offset field is always non-zero.
  */
 #define __SWP_TYPE_SHIFT	3
-#define __SWP_TYPE_BITS		6
+#define __SWP_TYPE_BITS		5
 #define __SWP_TYPE_MASK		((1 << __SWP_TYPE_BITS) - 1)
 #define __SWP_OFFSET_SHIFT	(__SWP_TYPE_BITS + __SWP_TYPE_SHIFT)
 

arch/arm/include/asm/sched_clock.h

@@ -10,5 +10,7 @@
 
 extern void sched_clock_postinit(void);
 extern void setup_sched_clock(u32 (*read)(void), int bits, unsigned long rate);
+extern void setup_sched_clock_needs_suspend(u32 (*read)(void), int bits,
+		unsigned long rate);
 
 #endif

arch/arm/kernel/sched_clock.c

@@ -21,6 +21,8 @@ struct clock_data {
 	u32 epoch_cyc_copy;
 	u32 mult;
 	u32 shift;
+	bool suspended;
+	bool needs_suspend;
 };
 
 static void sched_clock_poll(unsigned long wrap_ticks);
@@ -49,6 +51,9 @@ static unsigned long long cyc_to_sched_clock(u32 cyc, u32 mask)
 	u64 epoch_ns;
 	u32 epoch_cyc;
 
+	if (cd.suspended)
+		return cd.epoch_ns;
+
 	/*
 	 * Load the epoch_cyc and epoch_ns atomically.  We do this by
 	 * ensuring that we always write epoch_cyc, epoch_ns and
@@ -98,6 +103,13 @@ static void sched_clock_poll(unsigned long wrap_ticks)
 	update_sched_clock();
 }
 
+void __init setup_sched_clock_needs_suspend(u32 (*read)(void), int bits,
+		unsigned long rate)
+{
+	setup_sched_clock(read, bits, rate);
+	cd.needs_suspend = true;
+}
+
 void __init setup_sched_clock(u32 (*read)(void), int bits, unsigned long rate)
 {
 	unsigned long r, w;
@@ -169,11 +181,23 @@ void __init sched_clock_postinit(void)
 static int sched_clock_suspend(void)
 {
 	sched_clock_poll(sched_clock_timer.data);
+	if (cd.needs_suspend)
+		cd.suspended = true;
 	return 0;
 }
 
+static void sched_clock_resume(void)
+{
+	if (cd.needs_suspend) {
+		cd.epoch_cyc = read_sched_clock();
+		cd.epoch_cyc_copy = cd.epoch_cyc;
+		cd.suspended = false;
+	}
+}
+
 static struct syscore_ops sched_clock_ops = {
 	.suspend = sched_clock_suspend,
+	.resume = sched_clock_resume,
 };
 
 static int __init sched_clock_syscore_init(void)

arch/arm/kernel/topology.c

@@ -321,7 +321,7 @@ void store_cpu_topology(unsigned int cpuid)
  * init_cpu_topology is called at boot when only one cpu is running
  * which prevent simultaneous write access to cpu_topology array
  */
-void init_cpu_topology(void)
+void __init init_cpu_topology(void)
 {
 	unsigned int cpu;
 

arch/arm/lib/Makefile

@@ -16,13 +16,30 @@ lib-y		:= backtrace.o changebit.o csumipv6.o csumpartial.o   \
 		   call_with_stack.o
 
 mmu-y	:= clear_user.o copy_page.o getuser.o putuser.o
-mmu-y	+= copy_from_user.o copy_to_user.o
+
+# the code in uaccess.S is not preemption safe and
+# probably faster on ARMv3 only
+ifeq ($(CONFIG_PREEMPT),y)
+  mmu-y	+= copy_from_user.o copy_to_user.o
+else
+ifneq ($(CONFIG_CPU_32v3),y)
+  mmu-y	+= copy_from_user.o copy_to_user.o
+else
+  mmu-y	+= uaccess.o
+endif
+endif
 
 # using lib_ here won't override already available weak symbols
 obj-$(CONFIG_UACCESS_WITH_MEMCPY) += uaccess_with_memcpy.o
 
-lib-$(CONFIG_MMU)		+= $(mmu-y)
-lib-y				+= io-readsw-armv4.o io-writesw-armv4.o
+lib-$(CONFIG_MMU) += $(mmu-y)
+
+ifeq ($(CONFIG_CPU_32v3),y)
+  lib-y	+= io-readsw-armv3.o io-writesw-armv3.o
+else
+  lib-y	+= io-readsw-armv4.o io-writesw-armv4.o
+endif
+
 lib-$(CONFIG_ARCH_RPC)		+= ecard.o io-acorn.o floppydma.o
 lib-$(CONFIG_ARCH_SHARK)	+= io-shark.o
 

arch/arm/lib/io-readsw-armv3.S

@@ -0,0 +1,106 @@
+/*
+ *  linux/arch/arm/lib/io-readsw-armv3.S
+ *
+ *  Copyright (C) 1995-2000 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+.Linsw_bad_alignment:
+		adr	r0, .Linsw_bad_align_msg
+		mov	r2, lr
+		b	panic
+.Linsw_bad_align_msg:
+		.asciz	"insw: bad buffer alignment (0x%p, lr=0x%08lX)\n"
+		.align
+
+.Linsw_align:	tst	r1, #1
+		bne	.Linsw_bad_alignment
+
+		ldr	r3, [r0]
+		strb	r3, [r1], #1
+		mov	r3, r3, lsr #8
+		strb	r3, [r1], #1
+
+		subs	r2, r2, #1
+		moveq	pc, lr
+
+ENTRY(__raw_readsw)
+		teq	r2, #0		@ do we have to check for the zero len?
+		moveq	pc, lr
+		tst	r1, #3
+		bne	.Linsw_align
+
+.Linsw_aligned:	mov	ip, #0xff
+		orr	ip, ip, ip, lsl #8
+		stmfd	sp!, {r4, r5, r6, lr}
+
+		subs	r2, r2, #8
+		bmi	.Lno_insw_8
+
+.Linsw_8_lp:	ldr	r3, [r0]
+		and	r3, r3, ip
+		ldr	r4, [r0]
+		orr	r3, r3, r4, lsl #16
+
+		ldr	r4, [r0]
+		and	r4, r4, ip
+		ldr	r5, [r0]
+		orr	r4, r4, r5, lsl #16
+
+		ldr	r5, [r0]
+		and	r5, r5, ip
+		ldr	r6, [r0]
+		orr	r5, r5, r6, lsl #16
+
+		ldr	r6, [r0]
+		and	r6, r6, ip
+		ldr	lr, [r0]
+		orr	r6, r6, lr, lsl #16
+
+		stmia	r1!, {r3 - r6}
+
+		subs	r2, r2, #8
+		bpl	.Linsw_8_lp
+
+		tst	r2, #7
+		ldmeqfd	sp!, {r4, r5, r6, pc}
+
+.Lno_insw_8:	tst	r2, #4
+		beq	.Lno_insw_4
+
+		ldr	r3, [r0]
+		and	r3, r3, ip
+		ldr	r4, [r0]
+		orr	r3, r3, r4, lsl #16
+
+		ldr	r4, [r0]
+		and	r4, r4, ip
+		ldr	r5, [r0]
+		orr	r4, r4, r5, lsl #16
+
+		stmia	r1!, {r3, r4}
+
+.Lno_insw_4:	tst	r2, #2
+		beq	.Lno_insw_2
+
+		ldr	r3, [r0]
+		and	r3, r3, ip
+		ldr	r4, [r0]
+		orr	r3, r3, r4, lsl #16
+
+		str	r3, [r1], #4
+
+.Lno_insw_2:	tst	r2, #1
+		ldrne	r3, [r0]
+		strneb	r3, [r1], #1
+		movne	r3, r3, lsr #8
+		strneb	r3, [r1]
+
+		ldmfd	sp!, {r4, r5, r6, pc}
+
+

arch/arm/lib/io-writesw-armv3.S

@@ -0,0 +1,126 @@
+/*
+ *  linux/arch/arm/lib/io-writesw-armv3.S
+ *
+ *  Copyright (C) 1995-2000 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+.Loutsw_bad_alignment:
+		adr	r0, .Loutsw_bad_align_msg
+		mov	r2, lr
+		b	panic
+.Loutsw_bad_align_msg:
+		.asciz	"outsw: bad buffer alignment (0x%p, lr=0x%08lX)\n"
+		.align
+
+.Loutsw_align:	tst	r1, #1
+		bne	.Loutsw_bad_alignment
+
+		add	r1, r1, #2
+
+		ldr	r3, [r1, #-4]
+		mov	r3, r3, lsr #16
+		orr	r3, r3, r3, lsl #16
+		str	r3, [r0]
+		subs	r2, r2, #1
+		moveq	pc, lr
+
+ENTRY(__raw_writesw)
+		teq	r2, #0		@ do we have to check for the zero len?
+		moveq	pc, lr
+		tst	r1, #3
+		bne	.Loutsw_align
+
+		stmfd	sp!, {r4, r5, r6, lr}
+
+		subs	r2, r2, #8
+		bmi	.Lno_outsw_8
+
+.Loutsw_8_lp:	ldmia	r1!, {r3, r4, r5, r6}
+
+		mov	ip, r3, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r3, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+		mov	ip, r4, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r4, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+		mov	ip, r5, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r5, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+		mov	ip, r6, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r6, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+		subs	r2, r2, #8
+		bpl	.Loutsw_8_lp
+
+		tst	r2, #7
+		ldmeqfd	sp!, {r4, r5, r6, pc}
+
+.Lno_outsw_8:	tst	r2, #4
+		beq	.Lno_outsw_4
+
+		ldmia	r1!, {r3, r4}
+
+		mov	ip, r3, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r3, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+		mov	ip, r4, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r4, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+.Lno_outsw_4:	tst	r2, #2
+		beq	.Lno_outsw_2
+
+		ldr	r3, [r1], #4
+
+		mov	ip, r3, lsl #16
+		orr	ip, ip, ip, lsr #16
+		str	ip, [r0]
+
+		mov	ip, r3, lsr #16
+		orr	ip, ip, ip, lsl #16
+		str	ip, [r0]
+
+.Lno_outsw_2:	tst	r2, #1
+
+		ldrne	r3, [r1]
+
+		movne	ip, r3, lsl #16
+		orrne	ip, ip, ip, lsr #16
+		strne	ip, [r0]
+
+		ldmfd	sp!, {r4, r5, r6, pc}

arch/arm/lib/uaccess.S

@@ -0,0 +1,564 @@
+/*
+ *  linux/arch/arm/lib/uaccess.S
+ *
+ *  Copyright (C) 1995, 1996,1997,1998 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  Routines to block copy data to/from user memory
+ *   These are highly optimised both for the 4k page size
+ *   and for various alignments.
+ */
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/errno.h>
+#include <asm/domain.h>
+
+		.text
+
+#define PAGE_SHIFT 12
+
+/* Prototype: int __copy_to_user(void *to, const char *from, size_t n)
+ * Purpose  : copy a block to user memory from kernel memory
+ * Params   : to   - user memory
+ *          : from - kernel memory
+ *          : n    - number of bytes to copy
+ * Returns  : Number of bytes NOT copied.
+ */
+
+.Lc2u_dest_not_aligned:
+		rsb	ip, ip, #4
+		cmp	ip, #2
+		ldrb	r3, [r1], #1
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
+		ldrgeb	r3, [r1], #1
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
+		ldrgtb	r3, [r1], #1
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
+		sub	r2, r2, ip
+		b	.Lc2u_dest_aligned
+
+ENTRY(__copy_to_user)
+		stmfd	sp!, {r2, r4 - r7, lr}
+		cmp	r2, #4
+		blt	.Lc2u_not_enough
+		ands	ip, r0, #3
+		bne	.Lc2u_dest_not_aligned
+.Lc2u_dest_aligned:
+
+		ands	ip, r1, #3
+		bne	.Lc2u_src_not_aligned
+/*
+ * Seeing as there has to be at least 8 bytes to copy, we can
+ * copy one word, and force a user-mode page fault...
+ */
+
+.Lc2u_0fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lc2u_0nowords
+		ldr	r3, [r1], #4
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
+		mov	ip, r0, lsl #32 - PAGE_SHIFT	@ On each page, use a ld/st??t instruction
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lc2u_0fupi
+/*
+ * ip = max no. of bytes to copy before needing another "strt" insn
+ */
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #32
+		blt	.Lc2u_0rem8lp
+
+.Lc2u_0cpy8lp:	ldmia	r1!, {r3 - r6}
+		stmia	r0!, {r3 - r6}			@ Shouldnt fault
+		ldmia	r1!, {r3 - r6}
+		subs	ip, ip, #32
+		stmia	r0!, {r3 - r6}			@ Shouldnt fault
+		bpl	.Lc2u_0cpy8lp
+
+.Lc2u_0rem8lp:	cmn	ip, #16
+		ldmgeia	r1!, {r3 - r6}
+		stmgeia	r0!, {r3 - r6}			@ Shouldnt fault
+		tst	ip, #8
+		ldmneia	r1!, {r3 - r4}
+		stmneia	r0!, {r3 - r4}			@ Shouldnt fault
+		tst	ip, #4
+		ldrne	r3, [r1], #4
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
+		ands	ip, ip, #3
+		beq	.Lc2u_0fupi
+.Lc2u_0nowords:	teq	ip, #0
+		beq	.Lc2u_finished
+.Lc2u_nowords:	cmp	ip, #2
+		ldrb	r3, [r1], #1
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
+		ldrgeb	r3, [r1], #1
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
+		ldrgtb	r3, [r1], #1
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
+		b	.Lc2u_finished
+
+.Lc2u_not_enough:
+		movs	ip, r2
+		bne	.Lc2u_nowords
+.Lc2u_finished:	mov	r0, #0
+		ldmfd	sp!, {r2, r4 - r7, pc}
+
+.Lc2u_src_not_aligned:
+		bic	r1, r1, #3
+		ldr	r7, [r1], #4
+		cmp	ip, #2
+		bgt	.Lc2u_3fupi
+		beq	.Lc2u_2fupi
+.Lc2u_1fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lc2u_1nowords
+		mov	r3, r7, pull #8
+		ldr	r7, [r1], #4
+		orr	r3, r3, r7, push #24
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
+		mov	ip, r0, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lc2u_1fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lc2u_1rem8lp
+
+.Lc2u_1cpy8lp:	mov	r3, r7, pull #8
+		ldmia	r1!, {r4 - r7}
+		subs	ip, ip, #16
+		orr	r3, r3, r4, push #24
+		mov	r4, r4, pull #8
+		orr	r4, r4, r5, push #24
+		mov	r5, r5, pull #8
+		orr	r5, r5, r6, push #24
+		mov	r6, r6, pull #8
+		orr	r6, r6, r7, push #24
+		stmia	r0!, {r3 - r6}			@ Shouldnt fault
+		bpl	.Lc2u_1cpy8lp
+
+.Lc2u_1rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #8
+		ldmneia	r1!, {r4, r7}
+		orrne	r3, r3, r4, push #24
+		movne	r4, r4, pull #8
+		orrne	r4, r4, r7, push #24
+		stmneia	r0!, {r3 - r4}			@ Shouldnt fault
+		tst	ip, #4
+		movne	r3, r7, pull #8
+		ldrne	r7, [r1], #4
+		orrne	r3, r3, r7, push #24
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
+		ands	ip, ip, #3
+		beq	.Lc2u_1fupi
+.Lc2u_1nowords:	mov	r3, r7, get_byte_1
+		teq	ip, #0
+		beq	.Lc2u_finished
+		cmp	ip, #2
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
+		movge	r3, r7, get_byte_2
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
+		movgt	r3, r7, get_byte_3
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
+		b	.Lc2u_finished
+
+.Lc2u_2fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lc2u_2nowords
+		mov	r3, r7, pull #16
+		ldr	r7, [r1], #4
+		orr	r3, r3, r7, push #16
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
+		mov	ip, r0, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lc2u_2fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lc2u_2rem8lp
+
+.Lc2u_2cpy8lp:	mov	r3, r7, pull #16
+		ldmia	r1!, {r4 - r7}
+		subs	ip, ip, #16
+		orr	r3, r3, r4, push #16
+		mov	r4, r4, pull #16
+		orr	r4, r4, r5, push #16
+		mov	r5, r5, pull #16
+		orr	r5, r5, r6, push #16
+		mov	r6, r6, pull #16
+		orr	r6, r6, r7, push #16
+		stmia	r0!, {r3 - r6}			@ Shouldnt fault
+		bpl	.Lc2u_2cpy8lp
+
+.Lc2u_2rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #16
+		ldmneia	r1!, {r4, r7}
+		orrne	r3, r3, r4, push #16
+		movne	r4, r4, pull #16
+		orrne	r4, r4, r7, push #16
+		stmneia	r0!, {r3 - r4}			@ Shouldnt fault
+		tst	ip, #4
+		movne	r3, r7, pull #16
+		ldrne	r7, [r1], #4
+		orrne	r3, r3, r7, push #16
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
+		ands	ip, ip, #3
+		beq	.Lc2u_2fupi
+.Lc2u_2nowords:	mov	r3, r7, get_byte_2
+		teq	ip, #0
+		beq	.Lc2u_finished
+		cmp	ip, #2
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
+		movge	r3, r7, get_byte_3
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
+		ldrgtb	r3, [r1], #0
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
+		b	.Lc2u_finished
+
+.Lc2u_3fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lc2u_3nowords
+		mov	r3, r7, pull #24
+		ldr	r7, [r1], #4
+		orr	r3, r3, r7, push #8
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
+		mov	ip, r0, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lc2u_3fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lc2u_3rem8lp
+
+.Lc2u_3cpy8lp:	mov	r3, r7, pull #24
+		ldmia	r1!, {r4 - r7}
+		subs	ip, ip, #16
+		orr	r3, r3, r4, push #8
+		mov	r4, r4, pull #24
+		orr	r4, r4, r5, push #8
+		mov	r5, r5, pull #24
+		orr	r5, r5, r6, push #8
+		mov	r6, r6, pull #24
+		orr	r6, r6, r7, push #8
+		stmia	r0!, {r3 - r6}			@ Shouldnt fault
+		bpl	.Lc2u_3cpy8lp
+
+.Lc2u_3rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #24
+		ldmneia	r1!, {r4, r7}
+		orrne	r3, r3, r4, push #8
+		movne	r4, r4, pull #24
+		orrne	r4, r4, r7, push #8
+		stmneia	r0!, {r3 - r4}			@ Shouldnt fault
+		tst	ip, #4
+		movne	r3, r7, pull #24
+		ldrne	r7, [r1], #4
+		orrne	r3, r3, r7, push #8
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
+		ands	ip, ip, #3
+		beq	.Lc2u_3fupi
+.Lc2u_3nowords:	mov	r3, r7, get_byte_3
+		teq	ip, #0
+		beq	.Lc2u_finished
+		cmp	ip, #2
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
+		ldrgeb	r3, [r1], #1
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
+		ldrgtb	r3, [r1], #0
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
+		b	.Lc2u_finished
+ENDPROC(__copy_to_user)
+
+		.pushsection .fixup,"ax"
+		.align	0
+9001:		ldmfd	sp!, {r0, r4 - r7, pc}
+		.popsection
+
+/* Prototype: unsigned long __copy_from_user(void *to,const void *from,unsigned long n);
+ * Purpose  : copy a block from user memory to kernel memory
+ * Params   : to   - kernel memory
+ *          : from - user memory
+ *          : n    - number of bytes to copy
+ * Returns  : Number of bytes NOT copied.
+ */
+.Lcfu_dest_not_aligned:
+		rsb	ip, ip, #4
+		cmp	ip, #2
+USER(	TUSER(	ldrb)	r3, [r1], #1)			@ May fault
+		strb	r3, [r0], #1
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
+		strgeb	r3, [r0], #1
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
+		strgtb	r3, [r0], #1
+		sub	r2, r2, ip
+		b	.Lcfu_dest_aligned
+
+ENTRY(__copy_from_user)
+		stmfd	sp!, {r0, r2, r4 - r7, lr}
+		cmp	r2, #4
+		blt	.Lcfu_not_enough
+		ands	ip, r0, #3
+		bne	.Lcfu_dest_not_aligned
+.Lcfu_dest_aligned:
+		ands	ip, r1, #3
+		bne	.Lcfu_src_not_aligned
+
+/*
+ * Seeing as there has to be at least 8 bytes to copy, we can
+ * copy one word, and force a user-mode page fault...
+ */
+
+.Lcfu_0fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lcfu_0nowords
+USER(	TUSER(	ldr)	r3, [r1], #4)
+		str	r3, [r0], #4
+		mov	ip, r1, lsl #32 - PAGE_SHIFT	@ On each page, use a ld/st??t instruction
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lcfu_0fupi
+/*
+ * ip = max no. of bytes to copy before needing another "strt" insn
+ */
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #32
+		blt	.Lcfu_0rem8lp
+
+.Lcfu_0cpy8lp:	ldmia	r1!, {r3 - r6}			@ Shouldnt fault
+		stmia	r0!, {r3 - r6}
+		ldmia	r1!, {r3 - r6}			@ Shouldnt fault
+		subs	ip, ip, #32
+		stmia	r0!, {r3 - r6}
+		bpl	.Lcfu_0cpy8lp
+
+.Lcfu_0rem8lp:	cmn	ip, #16
+		ldmgeia	r1!, {r3 - r6}			@ Shouldnt fault
+		stmgeia	r0!, {r3 - r6}
+		tst	ip, #8
+		ldmneia	r1!, {r3 - r4}			@ Shouldnt fault
+		stmneia	r0!, {r3 - r4}
+		tst	ip, #4
+	TUSER(	ldrne) r3, [r1], #4			@ Shouldnt fault
+		strne	r3, [r0], #4
+		ands	ip, ip, #3
+		beq	.Lcfu_0fupi
+.Lcfu_0nowords:	teq	ip, #0
+		beq	.Lcfu_finished
+.Lcfu_nowords:	cmp	ip, #2
+USER(	TUSER(	ldrb)	r3, [r1], #1)			@ May fault
+		strb	r3, [r0], #1
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
+		strgeb	r3, [r0], #1
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
+		strgtb	r3, [r0], #1
+		b	.Lcfu_finished
+
+.Lcfu_not_enough:
+		movs	ip, r2
+		bne	.Lcfu_nowords
+.Lcfu_finished:	mov	r0, #0
+		add	sp, sp, #8
+		ldmfd	sp!, {r4 - r7, pc}
+
+.Lcfu_src_not_aligned:
+		bic	r1, r1, #3
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
+		cmp	ip, #2
+		bgt	.Lcfu_3fupi
+		beq	.Lcfu_2fupi
+.Lcfu_1fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lcfu_1nowords
+		mov	r3, r7, pull #8
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
+		orr	r3, r3, r7, push #24
+		str	r3, [r0], #4
+		mov	ip, r1, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lcfu_1fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lcfu_1rem8lp
+
+.Lcfu_1cpy8lp:	mov	r3, r7, pull #8
+		ldmia	r1!, {r4 - r7}			@ Shouldnt fault
+		subs	ip, ip, #16
+		orr	r3, r3, r4, push #24
+		mov	r4, r4, pull #8
+		orr	r4, r4, r5, push #24
+		mov	r5, r5, pull #8
+		orr	r5, r5, r6, push #24
+		mov	r6, r6, pull #8
+		orr	r6, r6, r7, push #24
+		stmia	r0!, {r3 - r6}
+		bpl	.Lcfu_1cpy8lp
+
+.Lcfu_1rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #8
+		ldmneia	r1!, {r4, r7}			@ Shouldnt fault
+		orrne	r3, r3, r4, push #24
+		movne	r4, r4, pull #8
+		orrne	r4, r4, r7, push #24
+		stmneia	r0!, {r3 - r4}
+		tst	ip, #4
+		movne	r3, r7, pull #8
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
+		orrne	r3, r3, r7, push #24
+		strne	r3, [r0], #4
+		ands	ip, ip, #3
+		beq	.Lcfu_1fupi
+.Lcfu_1nowords:	mov	r3, r7, get_byte_1
+		teq	ip, #0
+		beq	.Lcfu_finished
+		cmp	ip, #2
+		strb	r3, [r0], #1
+		movge	r3, r7, get_byte_2
+		strgeb	r3, [r0], #1
+		movgt	r3, r7, get_byte_3
+		strgtb	r3, [r0], #1
+		b	.Lcfu_finished
+
+.Lcfu_2fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lcfu_2nowords
+		mov	r3, r7, pull #16
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
+		orr	r3, r3, r7, push #16
+		str	r3, [r0], #4
+		mov	ip, r1, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lcfu_2fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lcfu_2rem8lp
+
+
+.Lcfu_2cpy8lp:	mov	r3, r7, pull #16
+		ldmia	r1!, {r4 - r7}			@ Shouldnt fault
+		subs	ip, ip, #16
+		orr	r3, r3, r4, push #16
+		mov	r4, r4, pull #16
+		orr	r4, r4, r5, push #16
+		mov	r5, r5, pull #16
+		orr	r5, r5, r6, push #16
+		mov	r6, r6, pull #16
+		orr	r6, r6, r7, push #16
+		stmia	r0!, {r3 - r6}
+		bpl	.Lcfu_2cpy8lp
+
+.Lcfu_2rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #16
+		ldmneia	r1!, {r4, r7}			@ Shouldnt fault
+		orrne	r3, r3, r4, push #16
+		movne	r4, r4, pull #16
+		orrne	r4, r4, r7, push #16
+		stmneia	r0!, {r3 - r4}
+		tst	ip, #4
+		movne	r3, r7, pull #16
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
+		orrne	r3, r3, r7, push #16
+		strne	r3, [r0], #4
+		ands	ip, ip, #3
+		beq	.Lcfu_2fupi
+.Lcfu_2nowords:	mov	r3, r7, get_byte_2
+		teq	ip, #0
+		beq	.Lcfu_finished
+		cmp	ip, #2
+		strb	r3, [r0], #1
+		movge	r3, r7, get_byte_3
+		strgeb	r3, [r0], #1
+USER(	TUSER(	ldrgtb) r3, [r1], #0)			@ May fault
+		strgtb	r3, [r0], #1
+		b	.Lcfu_finished
+
+.Lcfu_3fupi:	subs	r2, r2, #4
+		addmi	ip, r2, #4
+		bmi	.Lcfu_3nowords
+		mov	r3, r7, pull #24
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
+		orr	r3, r3, r7, push #8
+		str	r3, [r0], #4
+		mov	ip, r1, lsl #32 - PAGE_SHIFT
+		rsb	ip, ip, #0
+		movs	ip, ip, lsr #32 - PAGE_SHIFT
+		beq	.Lcfu_3fupi
+		cmp	r2, ip
+		movlt	ip, r2
+		sub	r2, r2, ip
+		subs	ip, ip, #16
+		blt	.Lcfu_3rem8lp
+
+.Lcfu_3cpy8lp:	mov	r3, r7, pull #24
+		ldmia	r1!, {r4 - r7}			@ Shouldnt fault
+		orr	r3, r3, r4, push #8
+		mov	r4, r4, pull #24
+		orr	r4, r4, r5, push #8
+		mov	r5, r5, pull #24
+		orr	r5, r5, r6, push #8
+		mov	r6, r6, pull #24
+		orr	r6, r6, r7, push #8
+		stmia	r0!, {r3 - r6}
+		subs	ip, ip, #16
+		bpl	.Lcfu_3cpy8lp
+
+.Lcfu_3rem8lp:	tst	ip, #8
+		movne	r3, r7, pull #24
+		ldmneia	r1!, {r4, r7}			@ Shouldnt fault
+		orrne	r3, r3, r4, push #8
+		movne	r4, r4, pull #24
+		orrne	r4, r4, r7, push #8
+		stmneia	r0!, {r3 - r4}
+		tst	ip, #4
+		movne	r3, r7, pull #24
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
+		orrne	r3, r3, r7, push #8
+		strne	r3, [r0], #4
+		ands	ip, ip, #3
+		beq	.Lcfu_3fupi
+.Lcfu_3nowords:	mov	r3, r7, get_byte_3
+		teq	ip, #0
+		beq	.Lcfu_finished
+		cmp	ip, #2
+		strb	r3, [r0], #1
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
+		strgeb	r3, [r0], #1
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
+		strgtb	r3, [r0], #1
+		b	.Lcfu_finished
+ENDPROC(__copy_from_user)
+
+		.pushsection .fixup,"ax"
+		.align	0
+		/*
+		 * We took an exception.  r0 contains a pointer to
+		 * the byte not copied.
+		 */
+9001:		ldr	r2, [sp], #4			@ void *to
+		sub	r2, r0, r2			@ bytes copied
+		ldr	r1, [sp], #4			@ unsigned long count
+		subs	r4, r1, r2			@ bytes left to copy
+		movne	r1, r4
+		blne	__memzero
+		mov	r0, r4
+		ldmfd	sp!, {r4 - r7, pc}
+		.popsection
+

arch/arm/mach-at91/at91rm9200_time.c

@@ -197,7 +197,7 @@ void __init at91rm9200_timer_init(void)
 	at91_st_read(AT91_ST_SR);
 
 	/* Make IRQs happen for the system timer */
-	setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq);
+	setup_irq(NR_IRQS_LEGACY + AT91_ID_SYS, &at91rm9200_timer_irq);
 
 	/* The 32KiHz "Slow Clock" (tick every 30517.58 nanoseconds) is used
 	 * directly for the clocksource and all clockevents, after adjusting

arch/arm/mach-at91/at91sam9260_devices.c

@@ -726,6 +726,8 @@ static struct resource rtt_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	},
 };
 
@@ -744,10 +746,12 @@ static void __init at91_add_device_rtt_rtc(void)
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9260_rtt_device.num_resources = 2;
+	at91sam9260_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9260_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)

arch/arm/mach-at91/at91sam9261_devices.c

@@ -609,6 +609,8 @@ static struct resource rtt_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -626,10 +628,12 @@ static void __init at91_add_device_rtt_rtc(void)
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9261_rtt_device.num_resources = 2;
+	at91sam9261_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9261_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)

arch/arm/mach-at91/at91sam9263_devices.c

@@ -990,6 +990,8 @@ static struct resource rtt0_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1006,6 +1008,8 @@ static struct resource rtt1_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1027,14 +1031,14 @@ static void __init at91_add_device_rtt_rtc(void)
 		 * The second resource is needed only for the chosen RTT:
 		 * GPBR will serve as the storage for RTC time offset
 		 */
-		at91sam9263_rtt0_device.num_resources = 2;
+		at91sam9263_rtt0_device.num_resources = 3;
 		at91sam9263_rtt1_device.num_resources = 1;
 		pdev = &at91sam9263_rtt0_device;
 		r = rtt0_resources;
 		break;
 	case 1:
 		at91sam9263_rtt0_device.num_resources = 1;
-		at91sam9263_rtt1_device.num_resources = 2;
+		at91sam9263_rtt1_device.num_resources = 3;
 		pdev = &at91sam9263_rtt1_device;
 		r = rtt1_resources;
 		break;
@@ -1047,6 +1051,8 @@ static void __init at91_add_device_rtt_rtc(void)
 	pdev->name = "rtc-at91sam9";
 	r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	r[1].end = r[1].start + 3;
+	r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -1293,6 +1293,8 @@ static struct resource rtt_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1310,10 +1312,12 @@ static void __init at91_add_device_rtt_rtc(void)
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9g45_rtt_device.num_resources = 2;
+	at91sam9g45_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9G45_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -688,6 +688,8 @@ static struct resource rtt_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -705,10 +707,12 @@ static void __init at91_add_device_rtt_rtc(void)
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9rl_rtt_device.num_resources = 2;
+	at91sam9rl_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9RL_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)

arch/arm/mach-at91/clock.c

@@ -63,6 +63,12 @@ EXPORT_SYMBOL_GPL(at91_pmc_base);
 
 #define cpu_has_300M_plla()	(cpu_is_at91sam9g10())
 
+#define cpu_has_240M_plla()	(cpu_is_at91sam9261() \
+				|| cpu_is_at91sam9263() \
+				|| cpu_is_at91sam9rl())
+
+#define cpu_has_210M_plla()	(cpu_is_at91sam9260())
+
 #define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
 				|| cpu_is_at91sam9g45() \
 				|| cpu_is_at91sam9x5() \
@@ -706,6 +712,12 @@ static int __init at91_pmc_init(unsigned long main_clock)
 	} else if (cpu_has_800M_plla()) {
 		if (plla.rate_hz > 800000000)
 			pll_overclock = true;
+	} else if (cpu_has_240M_plla()) {
+		if (plla.rate_hz > 240000000)
+			pll_overclock = true;
+	} else if (cpu_has_210M_plla()) {
+		if (plla.rate_hz > 210000000)
+			pll_overclock = true;
 	} else {
 		if (plla.rate_hz > 209000000)
 			pll_overclock = true;

arch/arm/mach-davinci/board-neuros-osd2.c

@@ -162,38 +162,6 @@ static void __init davinci_ntosd2_map_io(void)
 	dm644x_init();
 }
 
-/*
- I2C initialization
-*/
-static struct davinci_i2c_platform_data ntosd2_i2c_pdata = {
-	.bus_freq	= 20 /* kHz */,
-	.bus_delay	= 100 /* usec */,
-};
-
-static struct i2c_board_info __initdata ntosd2_i2c_info[] =  {
-};
-
-static	int ntosd2_init_i2c(void)
-{
-	int	status;
-
-	davinci_init_i2c(&ntosd2_i2c_pdata);
-	status = gpio_request(NTOSD2_MSP430_IRQ, ntosd2_i2c_info[0].type);
-	if (status == 0) {
-		status = gpio_direction_input(NTOSD2_MSP430_IRQ);
-		if (status == 0) {
-			status = gpio_to_irq(NTOSD2_MSP430_IRQ);
-			if (status > 0) {
-				ntosd2_i2c_info[0].irq = status;
-				i2c_register_board_info(1,
-					ntosd2_i2c_info,
-					ARRAY_SIZE(ntosd2_i2c_info));
-			}
-		}
-	}
-	return status;
-}
-
 static struct davinci_mmc_config davinci_ntosd2_mmc_config = {
 	.wires		= 4,
 	.version	= MMC_CTLR_VERSION_1
@@ -218,7 +186,6 @@ static __init void davinci_ntosd2_init(void)
 {
 	struct clk *aemif_clk;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
-	int	status;
 
 	aemif_clk = clk_get(NULL, "aemif");
 	clk_enable(aemif_clk);
@@ -242,12 +209,6 @@ static __init void davinci_ntosd2_init(void)
 	platform_add_devices(davinci_ntosd2_devices,
 				ARRAY_SIZE(davinci_ntosd2_devices));
 
-	/* Initialize I2C interface specific for this board */
-	status = ntosd2_init_i2c();
-	if (status < 0)
-		pr_warning("davinci_ntosd2_init: msp430 irq setup failed:"
-						"	 %d\n", status);
-
 	davinci_serial_init(&uart_config);
 	dm644x_init_asp(&dm644x_ntosd2_snd_data);
 

arch/arm/mach-dove/common.c

@@ -102,7 +102,8 @@ void __init dove_ehci1_init(void)
 void __init dove_ge00_init(struct mv643xx_eth_platform_data *eth_data)
 {
 	orion_ge00_init(eth_data, DOVE_GE00_PHYS_BASE,
-			IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR);
+			IRQ_DOVE_GE00_SUM, IRQ_DOVE_GE00_ERR,
+			1600);
 }
 
 /*****************************************************************************

arch/arm/mach-exynos/mach-origen.c

@@ -42,6 +42,7 @@
 #include <plat/backlight.h>
 #include <plat/fb.h>
 #include <plat/mfc.h>
+#include <plat/hdmi.h>
 
 #include <mach/ohci.h>
 #include <mach/map.h>
@@ -734,6 +735,11 @@ static void __init origen_bt_setup(void)
 	s3c_gpio_setpull(EXYNOS4_GPX2(2), S3C_GPIO_PULL_NONE);
 }
 
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* Direct HPD to HDMI chip */
@@ -781,6 +787,7 @@ static void __init origen_machine_init(void)
 
 	s5p_tv_setup();
 	s5p_i2c_hdmiphy_set_platdata(NULL);
+	s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
 
 #ifdef CONFIG_DRM_EXYNOS
 	s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;

arch/arm/mach-exynos/mach-smdkv310.c

@@ -40,6 +40,7 @@
 #include <plat/mfc.h>
 #include <plat/ehci.h>
 #include <plat/clock.h>
+#include <plat/hdmi.h>
 
 #include <mach/map.h>
 #include <mach/ohci.h>
@@ -354,6 +355,11 @@ static struct platform_pwm_backlight_data smdkv310_bl_data = {
 	.pwm_period_ns  = 1000,
 };
 
+/* I2C module and id for HDMIPHY */
+static struct i2c_board_info hdmiphy_info = {
+	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* direct HPD to HDMI chip */
@@ -388,6 +394,7 @@ static void __init smdkv310_machine_init(void)
 
 	s5p_tv_setup();
 	s5p_i2c_hdmiphy_set_platdata(NULL);
+	s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0);
 
 	samsung_keypad_set_platdata(&smdkv310_keypad_data);
 

arch/arm/mach-exynos/pm_domains.c

@@ -115,7 +115,7 @@ static __init int exynos_pm_dt_parse_domains(void)
 }
 #endif /* CONFIG_OF */
 
-static __init void exynos_pm_add_dev_to_genpd(struct platform_device *pdev,
+static __init __maybe_unused void exynos_pm_add_dev_to_genpd(struct platform_device *pdev,
 						struct exynos_pm_domain *pd)
 {
 	if (pdev->dev.bus) {

arch/arm/mach-gemini/irq.c

@@ -17,6 +17,7 @@
 #include <linux/sched.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
+#include <asm/system_misc.h>
 #include <mach/hardware.h>
 
 #define IRQ_SOURCE(base_addr)	(base_addr + 0x00)

arch/arm/mach-imx/Makefile

@@ -9,7 +9,8 @@ obj-$(CONFIG_SOC_IMX27) += clk-imx27.o mm-imx27.o ehci-imx27.o
 obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clk-imx31.o iomux-imx31.o ehci-imx31.o pm-imx3.o
 obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clk-imx35.o ehci-imx35.o pm-imx3.o
 
-obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o pm-imx5.o cpu_op-mx51.o
+imx5-pm-$(CONFIG_PM) += pm-imx5.o
+obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o mm-imx5.o clk-imx51-imx53.o ehci-imx5.o $(imx5-pm-y) cpu_op-mx51.o
 
 obj-$(CONFIG_COMMON_CLK) += clk-pllv1.o clk-pllv2.o clk-pllv3.o clk-gate2.o \
 			    clk-pfd.o clk-busy.o
@@ -70,14 +71,13 @@ obj-$(CONFIG_DEBUG_LL) += lluart.o
 obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
 obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
 obj-$(CONFIG_HAVE_IMX_SRC) += src.o
-obj-$(CONFIG_CPU_V7) += head-v7.o
-AFLAGS_head-v7.o :=-Wa,-march=armv7-a
-obj-$(CONFIG_SMP) += platsmp.o
+AFLAGS_headsmp.o :=-Wa,-march=armv7-a
+obj-$(CONFIG_SMP) += headsmp.o platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
 obj-$(CONFIG_SOC_IMX6Q) += clk-imx6q.o mach-imx6q.o
 
 ifeq ($(CONFIG_PM),y)
-obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
 endif
 
 # i.MX5 based machines

arch/arm/mach-imx/clk-imx27.c

@@ -223,7 +223,7 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[per3_gate], "per", "imx-fb.0");
 	clk_register_clkdev(clk[lcdc_ipg_gate], "ipg", "imx-fb.0");
 	clk_register_clkdev(clk[lcdc_ahb_gate], "ahb", "imx-fb.0");
-	clk_register_clkdev(clk[csi_ahb_gate], NULL, "mx2-camera.0");
+	clk_register_clkdev(clk[csi_ahb_gate], "ahb", "mx2-camera.0");
 	clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc");
 	clk_register_clkdev(clk[usb_ipg_gate], "ipg", "fsl-usb2-udc");
 	clk_register_clkdev(clk[usb_ahb_gate], "ahb", "fsl-usb2-udc");
@@ -250,8 +250,10 @@ int __init mx27_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[i2c2_ipg_gate], NULL, "imx-i2c.1");
 	clk_register_clkdev(clk[owire_ipg_gate], NULL, "mxc_w1.0");
 	clk_register_clkdev(clk[kpp_ipg_gate], NULL, "imx-keypad");
-	clk_register_clkdev(clk[emma_ahb_gate], "ahb", "imx-emma");
-	clk_register_clkdev(clk[emma_ipg_gate], "ipg", "imx-emma");
+	clk_register_clkdev(clk[emma_ahb_gate], "emma-ahb", "mx2-camera.0");
+	clk_register_clkdev(clk[emma_ipg_gate], "emma-ipg", "mx2-camera.0");
+	clk_register_clkdev(clk[emma_ahb_gate], "ahb", "m2m-emmaprp.0");
+	clk_register_clkdev(clk[emma_ipg_gate], "ipg", "m2m-emmaprp.0");
 	clk_register_clkdev(clk[iim_ipg_gate], "iim", NULL);
 	clk_register_clkdev(clk[gpio_ipg_gate], "gpio", NULL);
 	clk_register_clkdev(clk[brom_ahb_gate], "brom", NULL);

arch/arm/mach-imx/clk-imx31.c

@@ -130,7 +130,7 @@ int __init mx31_clocks_init(unsigned long fref)
 	clk_register_clkdev(clk[nfc], NULL, "mxc_nand.0");
 	clk_register_clkdev(clk[ipu_gate], NULL, "ipu-core");
 	clk_register_clkdev(clk[ipu_gate], NULL, "mx3_sdc_fb");
-	clk_register_clkdev(clk[kpp_gate], "kpp", NULL);
+	clk_register_clkdev(clk[kpp_gate], NULL, "imx-keypad");
 	clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.0");
 	clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.0");
 	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.0");

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -303,6 +303,7 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk_prepare_enable(clk[aips_tz2]); /* fec */
 	clk_prepare_enable(clk[spba]);
 	clk_prepare_enable(clk[emi_fast_gate]); /* fec */
+	clk_prepare_enable(clk[emi_slow_gate]); /* eim */
 	clk_prepare_enable(clk[tmax1]);
 	clk_prepare_enable(clk[tmax2]); /* esdhc2, fec */
 	clk_prepare_enable(clk[tmax3]); /* esdhc1, esdhc4 */

arch/arm/mach-imx/clk-imx6q.c

@@ -152,7 +152,7 @@ enum mx6q_clks {
 	ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
 	usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
 	pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
-	ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2,
+	ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2, ldb_di0_div_3_5, ldb_di1_div_3_5,
 	clk_max
 };
 
@@ -288,8 +288,10 @@ int __init mx6q_clocks_init(void)
 	clk[gpu3d_shader]     = imx_clk_divider("gpu3d_shader",     "gpu3d_shader_sel",  base + 0x18, 29, 3);
 	clk[ipu1_podf]        = imx_clk_divider("ipu1_podf",        "ipu1_sel",          base + 0x3c, 11, 3);
 	clk[ipu2_podf]        = imx_clk_divider("ipu2_podf",        "ipu2_sel",          base + 0x3c, 16, 3);
-	clk[ldb_di0_podf]     = imx_clk_divider("ldb_di0_podf",     "ldb_di0_sel",       base + 0x20, 10, 1);
-	clk[ldb_di1_podf]     = imx_clk_divider("ldb_di1_podf",     "ldb_di1_sel",       base + 0x20, 11, 1);
+	clk[ldb_di0_div_3_5]  = imx_clk_fixed_factor("ldb_di0_div_3_5", "ldb_di0_sel", 2, 7);
+	clk[ldb_di0_podf]     = imx_clk_divider("ldb_di0_podf",     "ldb_di0_div_3_5",       base + 0x20, 10, 1);
+	clk[ldb_di1_div_3_5]  = imx_clk_fixed_factor("ldb_di1_div_3_5", "ldb_di1_sel", 2, 7);
+	clk[ldb_di1_podf]     = imx_clk_divider("ldb_di1_podf",     "ldb_di1_div_3_5",   base + 0x20, 11, 1);
 	clk[ipu1_di0_pre]     = imx_clk_divider("ipu1_di0_pre",     "ipu1_di0_pre_sel",  base + 0x34, 3,  3);
 	clk[ipu1_di1_pre]     = imx_clk_divider("ipu1_di1_pre",     "ipu1_di1_pre_sel",  base + 0x34, 12, 3);
 	clk[ipu2_di0_pre]     = imx_clk_divider("ipu2_di0_pre",     "ipu2_di0_pre_sel",  base + 0x38, 3,  3);

arch/arm/mach-imx/hotplug.c

@@ -42,22 +42,6 @@ static inline void cpu_enter_lowpower(void)
 	  : "cc");
 }
 
-static inline void cpu_leave_lowpower(void)
-{
-	unsigned int v;
-
-	asm volatile(
-		"mrc	p15, 0, %0, c1, c0, 0\n"
-	"	orr	%0, %0, %1\n"
-	"	mcr	p15, 0, %0, c1, c0, 0\n"
-	"	mrc	p15, 0, %0, c1, c0, 1\n"
-	"	orr	%0, %0, %2\n"
-	"	mcr	p15, 0, %0, c1, c0, 1\n"
-	  : "=&r" (v)
-	  : "Ir" (CR_C), "Ir" (0x40)
-	  : "cc");
-}
-
 /*
  * platform-specific code to shutdown a CPU
  *
@@ -67,11 +51,10 @@ void platform_cpu_die(unsigned int cpu)
 {
 	cpu_enter_lowpower();
 	imx_enable_cpu(cpu, false);
-	cpu_do_idle();
-	cpu_leave_lowpower();
 
-	/* We should never return from idle */
-	panic("cpu %d unexpectedly exit from shutdown\n", cpu);
+	/* spin here until hardware takes it down */
+	while (1)
+		;
 }
 
 int platform_cpu_disable(unsigned int cpu)

arch/arm/mach-imx/mach-imx6q.c

@@ -71,7 +71,7 @@ soft:
 /* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
 static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 {
-	if (IS_ENABLED(CONFIG_PHYLIB)) {
+	if (IS_BUILTIN(CONFIG_PHYLIB)) {
 		/* min rx data delay */
 		phy_write(phydev, 0x0b, 0x8105);
 		phy_write(phydev, 0x0c, 0x0000);
@@ -112,7 +112,7 @@ put_clk:
 
 static void __init imx6q_sabrelite_init(void)
 {
-	if (IS_ENABLED(CONFIG_PHYLIB))
+	if (IS_BUILTIN(CONFIG_PHYLIB))
 		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
 				ksz9021rn_phy_fixup);
 	imx6q_sabrelite_cko1_setup();

arch/arm/mach-integrator/core.c

@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/device.h>
+#include <linux/export.h>
 #include <linux/spinlock.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>

arch/arm/mach-integrator/integrator_ap.c

@@ -456,7 +456,7 @@ static void __init ap_init_timer(void)
 
 	clk = clk_get_sys("ap_timer", NULL);
 	BUG_ON(IS_ERR(clk));
-	clk_enable(clk);
+	clk_prepare_enable(clk);
 	rate = clk_get_rate(clk);
 
 	writel(0, TIMER0_VA_BASE + TIMER_CTRL);

arch/arm/mach-kirkwood/Makefile.boot

@@ -7,7 +7,8 @@ dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns320.dtb
 dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb
 dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb
 dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb
-dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-qnap-ts219.dtb
+dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-ts219-6281.dtb
+dtb-$(CONFIG_MACH_TS219_DT)	+= kirkwood-ts219-6282.dtb
 dtb-$(CONFIG_MACH_GOFLEXNET_DT) += kirkwood-goflexnet.dtb
-dbt-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
-dbt-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb
+dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lschlv2.dtb
+dtb-$(CONFIG_MACH_LSXL_DT) += kirkwood-lsxhl.dtb

arch/arm/mach-kirkwood/common.c

@@ -301,7 +301,7 @@ void __init kirkwood_ge00_init(struct mv643xx_eth_platform_data *eth_data)
 {
 	orion_ge00_init(eth_data,
 			GE00_PHYS_BASE, IRQ_KIRKWOOD_GE00_SUM,
-			IRQ_KIRKWOOD_GE00_ERR);
+			IRQ_KIRKWOOD_GE00_ERR, 1600);
 	/* The interface forgets the MAC address assigned by u-boot if
 	the clock is turned off, so claim the clk now. */
 	clk_prepare_enable(ge0);
@@ -315,7 +315,7 @@ void __init kirkwood_ge01_init(struct mv643xx_eth_platform_data *eth_data)
 {
 	orion_ge01_init(eth_data,
 			GE01_PHYS_BASE, IRQ_KIRKWOOD_GE01_SUM,
-			IRQ_KIRKWOOD_GE01_ERR);
+			IRQ_KIRKWOOD_GE01_ERR, 1600);
 	clk_prepare_enable(ge1);
 }
 
@@ -517,6 +517,13 @@ void __init kirkwood_wdt_init(void)
 void __init kirkwood_init_early(void)
 {
 	orion_time_set_base(TIMER_VIRT_BASE);
+
+	/*
+	 * Some Kirkwood devices allocate their coherent buffers from atomic
+	 * context. Increase size of atomic coherent pool to make sure such
+	 * the allocations won't fail.
+	 */
+	init_dma_coherent_pool_size(SZ_1M);
 }
 
 int kirkwood_tclk;

arch/arm/mach-kirkwood/db88f6281-bp-setup.c

@@ -10,6 +10,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/sizes.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/partitions.h>
 #include <linux/ata_platform.h>

arch/arm/mach-mmp/sram.c

@@ -68,7 +68,7 @@ static int __devinit sram_probe(struct platform_device *pdev)
 	struct resource *res;
 	int ret = 0;
 
-	if (!pdata && !pdata->pool_name)
+	if (!pdata || !pdata->pool_name)
 		return -ENODEV;
 
 	info = kzalloc(sizeof(*info), GFP_KERNEL);