Pull PA-RISC fixes from James Bottomley:
"This is a set of three bug fixes that gets parisc running again on
systems with PA1.1 processors.
Two fix regressions introduced in 2.6.39 and one fixes a prefetch bug
that only affects PA7300LC processors. We also have another pending
fix to do with the sectional arrangement of vmlinux.lds, but there's a
query on it during testing on one particular system type, so I'll hold
off sending it in for now."
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix panic on prefetch(NULL) on PA7300LC
[PARISC] fix crash in flush_icache_page_asm on PA1.1
[PARISC] fix PA1.1 oops on boot
Pull x86 linker bug workarounds from Peter Anvin.
GNU ld-2.22.52.0.[12] (*) has an unfortunate bug where it incorrectly
turns certain relocation entries absolute. Section-relative symbols
that are part of otherwise empty sections are silently changed them to
absolute. We rely on section-relative symbols staying section-relative,
and actually have several sections in the linker script solely for this
purpose.
See for example
http://sourceware.org/bugzilla/show_bug.cgi?id=14052
We could just black-list the buggy linker, but it appears that it got
shipped in at least F17, and possibly other distros too, so it's sadly
not some rare unusual case.
This backports the workaround from the x86/trampoline branch, and as
Peter says: "This is not a minimal fix, not at all, but it is a tested
code base."
* 'x86/ld-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: When printing an error, say relative or absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
x86, realmode: 16-bit real-mode code support for relocs tool
(*) That's a manly release numbering system. Stupid, sure. But manly.
Pull block layer fixes from Jens Axboe:
"A few small, but important fixes. Most of them are marked for stable
as well
- Fix failure to release a semaphore on error path in mtip32xx.
- Fix crashable condition in bio_get_nr_vecs().
- Don't mark end-of-disk buffers as mapped, limit it to i_size.
- Fix for build problem with CONFIG_BLOCK=n on arm at least.
- Fix for a buffer overlow on UUID partition printing.
- Trivial removal of unused variables in dac960."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix buffer overflow when printing partition UUIDs
Fix blkdev.h build errors when BLOCK=n
bio allocation failure due to bio_get_nr_vecs()
block: don't mark buffers beyond end of disk as mapped
mtip32xx: release the semaphore on an error path
dac960: Remove unused variables from DAC960_CreateProcEntries()
Pull one more networking bug-fix from David Miller:
"One last straggler.
Eric Dumazet's pktgen unload oops fix was not entirely complete, but
all the cases should be handled properly now.... fingers crossed."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
pktgen: fix module unload for good
Occasionally, testing memcg's move_charge_at_immigrate on rc7 shows
a flurry of hundreds of warnings at kernel/res_counter.c:96, where
res_counter_uncharge_locked() does WARN_ON(counter->usage < val).
The first trace of each flurry implicates __mem_cgroup_cancel_charge()
of mc.precharge, and an audit of mc.precharge handling points to
mem_cgroup_move_charge_pte_range()'s THP handling in commit 12724850e8
("memcg: avoid THP split in task migration").
Checking !mc.precharge is good everywhere else, when a single page is to
be charged; but here the "mc.precharge -= HPAGE_PMD_NR" likely to
follow, is liable to result in underflow (a lot can change since the
precharge was estimated).
Simply check against HPAGE_PMD_NR: there's probably a better
alternative, trying precharge for more, splitting if unsuccessful; but
this one-liner is safer for now - no kernel/res_counter.c:96 warnings
seen in 26 hours.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the relocs tool throws an error, let the error message say if it
is an absolute or relative symbol. This should make it a lot more
clear what action the programmer needs to take and should help us find
the reason if additional symbol bugs show up.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
GNU ld 2.22.52.0.1 has a bug that it blindly changes symbols from
section-relative to absolute if they are in a section of zero length.
This turns the symbols __init_begin and __init_end into absolute
symbols. Let the relocs program know that those should be treated as
relative symbols.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
A new option is added to the relocs tool called '--realmode'.
This option causes the generation of 16-bit segment relocations
and 32-bit linear relocations for the real-mode code. When
the real-mode code is moved to the low-memory during kernel
initialization, these relocation entries can be used to
relocate the code properly.
In the assembly code 16-bit segment relocations must be relative
to the 'real_mode_seg' absolute symbol. Linear relocations must be
relative to a symbol prefixed with 'pa_'.
16-bit segment relocation is used to load cs:ip in 16-bit code.
Linear relocations are used in the 32-bit code for relocatable
data references. They are declared in the linker script of the
real-mode code.
The relocs tool is moved to arch/x86/tools/relocs.c, and added new
target archscripts that can be used to build scripts needed building
an architecture. be compiled before building the arch/x86 tree.
[ hpa: accelerating this because it detects invalid absolute
relocations, a serious bug in binutils 2.22.52.0.x which currently
produces bad kernels. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-2-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Pull a dm fix from Alasdair G Kergon:
"A fix to the thin provisioning userspace interface."
* tag 'dm-3.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: fix table output when pool target disables discard passdown internally
When the thin pool target clears the discard_passdown parameter
internally, it incorrectly changes the table line reported to userspace.
This breaks dumb string comparisons on these table lines in generic
userspace device-mapper library code and leads to tables being reloaded
repeatedly when nothing is actually meant to be changing.
This patch corrects this by no longer changing the table line when
discard passdown was disabled.
We can still tell when discard passdown is overridden by looking for the
message "Discard unsupported by data device (sdX): Disabling discard passdown."
This automatic detection is also moved from the 'load' to the 'resume'
so that it is re-evaluated should the properties of underlying devices
change.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull one more md bugfix from NeilBrown:
"Fix bug in recent fix to RAID10.
Without this patch, recovery will crash"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/raid10: fix transcription error in calc_sectors conversion.
Pull tile tree bugfix from Chris Metcalf:
"This fixes a security vulnerability (and correctness bug) in tilegx"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tilegx: enable SYSCALL_WRAPPERS support
The old code was
sector_div(stride, fc);
the new code was
sector_dir(size, conf->near_copies);
'size' is right (the stride various wasn't really needed), but
'fc' means 'far_copies', and that is an important difference.
Signed-off-by: NeilBrown <neilb@suse.de>
Merge misc fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (4 patches)
frv: delete incorrect task prototypes causing compile fail
slub: missing test for partial pages flush work in flush_all()
fs, proc: fix ABBA deadlock in case of execution attempt of map_files/ entries
drivers/rtc/rtc-pl031.c: configure correct wday for 2000-01-01
Instead of doing the i_mode calculations at proc_fd_instantiate() time,
move them into tid_fd_revalidate(), which is where the other inode state
(notably uid/gid information) is updated too.
Otherwise we'll end up with stale i_mode information if an fd is re-used
while the dentry still hangs around. Not that anything really *cares*
(symlink permissions don't really matter), but Tetsuo Handa noticed that
the owner read/write bits don't always match the state of the
readability of the file descriptor, and we _used_ to get this right a
long time ago in a galaxy far, far away.
Besides, aside from fixing an ugly detail (that has apparently been this
way since commit 61a2878402: "proc: Remove the hard coded inode
numbers" in 2006), this removes more lines of code than it adds. And it
just makes sense to update i_mode in the same place we update i_uid/gid.
Al Viro correctly points out that we could just do the inode fill in the
inode iops ->getattr() function instead. However, that does require
somewhat slightly more invasive changes, and adds yet *another* lookup
of the file descriptor. We need to do the revalidate() for other
reasons anyway, and have the file descriptor handy, so we might as well
fill in the information at this point.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit c57b546840 (pktgen: fix crash at module unload) did a very poor
job with list primitives.
1) list_splice() arguments were in the wrong order
2) list_splice(list, head) has undefined behavior if head is not
initialized.
3) We should use the list_splice_init() variant to clear pktgen_threads
list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some discussion with the glibc mailing lists revealed that this was
necessary for 64-bit platforms with MIPS-like sign-extension rules
for 32-bit values. The original symptom was that passing (uid_t)-1 to
setreuid() was failing in programs linked -pthread because of the "setxid"
mechanism for passing setxid-type function arguments to the syscall code.
SYSCALL_WRAPPERS handles ensuring that all syscall arguments end up with
proper sign-extension and is thus the appropriate fix for this problem.
On other platforms (s390, powerpc, sparc64, and mips) this was fixed
in 2.6.28.6. The general issue is tracked as CVE-2009-0029.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull a machine check recovery fix from Tony Luck.
I really don't like how the MCE code does some of the things it does,
but this does seem to be an improvement.
* tag 'linus-mce-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Only restart instruction after machine check recovery if it is safe
Commit 41101809a8 ("fork: Provide weak arch_release_[task_struct|
thread_info] functions") in -tip highlights a problem in the frv arch,
where it has needles prototypes for alloc_task_struct_node and
free_task_struct. This now shows up as:
kernel/fork.c:120:66: error: static declaration of 'alloc_task_struct_node' follows non-static declaration
kernel/fork.c:127:51: error: static declaration of 'free_task_struct' follows non-static declaration
since that commit turned them into real functions. Since arch/frv does
does not define define __HAVE_ARCH_TASK_STRUCT_ALLOCATOR (i.e. it just
uses the generic ones) it shouldn't list these at all.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found some kernel messages such as:
SLUB raid5-md127: kmem_cache_destroy called for cache that still has objects.
Pid: 6143, comm: mdadm Tainted: G O 3.4.0-rc6+ #75
Call Trace:
kmem_cache_destroy+0x328/0x400
free_conf+0x2d/0xf0 [raid456]
stop+0x41/0x60 [raid456]
md_stop+0x1a/0x60 [md_mod]
do_md_stop+0x74/0x470 [md_mod]
md_ioctl+0xff/0x11f0 [md_mod]
blkdev_ioctl+0xd8/0x7a0
block_ioctl+0x3b/0x40
do_vfs_ioctl+0x96/0x560
sys_ioctl+0x91/0xa0
system_call_fastpath+0x16/0x1b
Then using kmemleak I found these messages:
unreferenced object 0xffff8800b6db7380 (size 112):
comm "mdadm", pid 5783, jiffies 4294810749 (age 90.589s)
hex dump (first 32 bytes):
01 01 db b6 ad 4e ad de ff ff ff ff ff ff ff ff .....N..........
ff ff ff ff ff ff ff ff 98 40 4a 82 ff ff ff ff .........@J.....
backtrace:
kmemleak_alloc+0x21/0x50
kmem_cache_alloc+0xeb/0x1b0
kmem_cache_open+0x2f1/0x430
kmem_cache_create+0x158/0x320
setup_conf+0x649/0x770 [raid456]
run+0x68b/0x840 [raid456]
md_run+0x529/0x940 [md_mod]
do_md_run+0x18/0xc0 [md_mod]
md_ioctl+0xba8/0x11f0 [md_mod]
blkdev_ioctl+0xd8/0x7a0
block_ioctl+0x3b/0x40
do_vfs_ioctl+0x96/0x560
sys_ioctl+0x91/0xa0
system_call_fastpath+0x16/0x1b
This bug was introduced by commit a8364d5555 ("slub: only IPI CPUs that
have per cpu obj to flush"), which did not include checks for per cpu
partial pages being present on a cpu.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
map_files/ entries are never supposed to be executed, still curious
minds might try to run them, which leads to the following deadlock
======================================================
[ INFO: possible circular locking dependency detected ]
3.4.0-rc4-24406-g841e6a6 #121 Not tainted
-------------------------------------------------------
bash/1556 is trying to acquire lock:
(&sb->s_type->i_mutex_key#8){+.+.+.}, at: do_lookup+0x267/0x2b1
but task is already holding lock:
(&sig->cred_guard_mutex){+.+.+.}, at: prepare_bprm_creds+0x2d/0x69
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&sig->cred_guard_mutex){+.+.+.}:
validate_chain+0x444/0x4f4
__lock_acquire+0x387/0x3f8
lock_acquire+0x12b/0x158
__mutex_lock_common+0x56/0x3a9
mutex_lock_killable_nested+0x40/0x45
lock_trace+0x24/0x59
proc_map_files_lookup+0x5a/0x165
__lookup_hash+0x52/0x73
do_lookup+0x276/0x2b1
walk_component+0x3d/0x114
do_last+0xfc/0x540
path_openat+0xd3/0x306
do_filp_open+0x3d/0x89
do_sys_open+0x74/0x106
sys_open+0x21/0x23
tracesys+0xdd/0xe2
-> #0 (&sb->s_type->i_mutex_key#8){+.+.+.}:
check_prev_add+0x6a/0x1ef
validate_chain+0x444/0x4f4
__lock_acquire+0x387/0x3f8
lock_acquire+0x12b/0x158
__mutex_lock_common+0x56/0x3a9
mutex_lock_nested+0x40/0x45
do_lookup+0x267/0x2b1
walk_component+0x3d/0x114
link_path_walk+0x1f9/0x48f
path_openat+0xb6/0x306
do_filp_open+0x3d/0x89
open_exec+0x25/0xa0
do_execve_common+0xea/0x2f9
do_execve+0x43/0x45
sys_execve+0x43/0x5a
stub_execve+0x6c/0xc0
This is because prepare_bprm_creds grabs task->signal->cred_guard_mutex
and when do_lookup happens we try to grab task->signal->cred_guard_mutex
again in lock_trace.
Fix it using plain ptrace_may_access() helper in proc_map_files_lookup()
and in proc_map_files_readdir() instead of lock_trace(), the caller must
be CAP_SYS_ADMIN granted anyway.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
"Small set of fixes again."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7419/1: vfp: fix VFP flushing regression on sigreturn path
ARM: 7418/1: LPAE: fix access flag setup in mem_type_table
ARM: prevent VM_GROWSDOWN mmaps extending below FIRST_USER_ADDRESS
ARM: 7417/1: vfp: ensure preemption is disabled when enabling VFP access
Pull two networking fixes from David S. Miller:
1) Thanks to Willy Tarreau and Eric Dumazet, we've unlocked a bug that's
been present in do_tcp_sendpages() since that function was written in
2002.
When we block to wait for memory we have to unconditionally try and
push out pending TCP data, otherwise we can block for an unreasonably
long amount of time.
2) Fix deadlock in e1000, fixes kernel bugzilla 43132
From Tushar Dave.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
e1000: Prevent reset task killing itself.
tcp: do_tcp_sendpages() must try to push data out on oom conditions
Commit 1cc0c998fd ("ACPI: Fix D3hot v D3cold confusion") introduced a
bug in __acpi_bus_set_power() and changed the behavior of
acpi_pci_set_power_state() in such a way that it generally doesn't work
as expected if PCI_D3hot is passed to it as the second argument.
First off, if ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) is passed to
__acpi_bus_set_power() and the explicit_set flag is set for the D3cold
state, the function will try to execute AML method called "_PS4", which
doesn't exist.
Fix this by adding a check to ensure that the name of the AML method
to execute for transitions to ACPI_STATE_D3_COLD is correct in
__acpi_bus_set_power(). Also make sure that the explicit_set flag
for ACPI_STATE_D3_COLD will be set if _PS3 is present and modify
acpi_power_transition() to avoid accessing power resources for
ACPI_STATE_D3_COLD, because they don't exist.
Second, if PCI_D3hot is passed to acpi_pci_set_power_state() as the
target state, the function will request a transition to
ACPI_STATE_D3_HOT instead of ACPI_STATE_D3. However,
ACPI_STATE_D3_HOT is now only marked as supported if the _PR3 AML
method is defined for the given device, which is rare. This causes
problems to happen on systems where devices were successfully put
into ACPI D3 by pci_set_power_state(PCI_D3hot) which doesn't work
now. In particular, some unused graphics adapters are not turned
off as a result.
To fix this issue restore the old behavior of
acpi_pci_set_power_state(), which is to request a transition to
ACPI_STATE_D3 (equal to ACPI_STATE_D3_COLD) if either PCI_D3hot or
PCI_D3cold is passed to it as the argument.
This approach is not ideal, because generally power should not
be removed from devices if PCI_D3hot is the target power state,
but since this behavior is relied on, we have no choice but to
restore it at the moment and spend more time on designing a
better solution in the future.
References: https://bugzilla.kernel.org/show_bug.cgi?id=43228
Reported-by: rocko <rockorequin@hotmail.com>
Reported-by: Cristian Rodríguez <crrodriguez@opensuse.org>
Reported-and-tested-by: Peter <lekensteyn@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since recent changes on TCP splicing (starting with commits 2f533844
"tcp: allow splice() to build full TSO packets" and 35f9c09f "tcp:
tcp_sendpages() should call tcp_push() once"), I started seeing
massive stalls when forwarding traffic between two sockets using
splice() when pipe buffers were larger than socket buffers.
Latest changes (net: netdev_alloc_skb() use build_skb()) made the
problem even more apparent.
The reason seems to be that if do_tcp_sendpages() fails on out of memory
condition without being able to send at least one byte, tcp_push() is not
called and the buffers cannot be flushed.
After applying the attached patch, I cannot reproduce the stalls at all
and the data rate it perfectly stable and steady under any condition
which previously caused the problem to be permanent.
The issue seems to have been there since before the kernel migrated to
git, which makes me think that the stalls I occasionally experienced
with tux during stress-tests years ago were probably related to the
same issue.
This issue was first encountered on 3.0.31 and 3.2.17, so please backport
to -stable.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Pull two more target-core updates from Nicholas Bellinger:
"The first patch addresses a SPC-2 reservations RELEASE bug in a
special (iscsi specific) multi-ISID setup case that was allowing the
same initiator to be able to incorrect release it's own reservation on
a different SCSI path with enforce_pr_isid=1 operation. This bug was
caught by Bernhard Kohl.
The second patch is to address a bug with FILEIO backends where the
incorrect number of blocks for READ_CAPACITY was being reported after
an underlying device-mapper block_device size change. This patch uses
now i_size_read() in fd_get_blocks() for FILEIO backends with an
underlying block_device, instead of trying to determine this value at
setup time during fd_create_virtdevice(). (hch CC'ed)
Both are CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix bug in handling of FILEIO + block_device resize ops
target: Fix SPC-2 RELEASE bug for multi-session iSCSI client setups
This patch fixes a bug in the handling of FILEIO w/ underlying block_device
resize operations where the original fd_dev->fd_dev_size was incorrectly being
used in fd_get_blocks() for READ_CAPACITY response payloads.
This patch avoids using fd_dev->fd_dev_size for FILEIO devices with
an underlying block_device, and instead changes fd_get_blocks() to
get the sector count directly from i_size_read() as recommended by hch.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull last minute virtio fixes from Michael S. Tsirkin:
"Here are a couple of last minute virtio fixes for 3.4. Hope it's not
too late yes - I might have tried too hard to make sure the fix is
well tested.
Fixes are by Amit and myself. One fixes module removal and one
suspend of a VM, the last one the handling of out of memory condition.
They are thus very low risk as most people never hit these paths, but
do fix very annoying problems for people that do use the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: invoke softirqs after __napi_schedule
virtio: balloon: let host know of updated balloon size before module removal
virtio: console: tell host of open ports after resume from s3/s4
Pull ARM: SoC fixes from Olof Johansson:
"I will stop trying to predict when we're done with fixes for a
release.
Here's another small batch of three patches for arm-soc:
- A fix for a boot time WARN_ON() due to irq domain conversion on
PRIMA2
- Fix for a regression in Tegra SMP spinup code due to swapped
register offsets
- Fixed config dependency for mv_cesa crypto driver to avoid build
breakage"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: fix irq domain size and IRQ mask of internal interrupt controller
crypto: mv_cesa requires on CRYPTO_HASH to build
ARM: tegra: Fix flow controller accesses
Pull two md fixes from NeilBrown:
"One fixes a bug in the new raid10 resize code so is relevant to 3.4
only.
The other fixes a bug in the use of md by dm-raid, so is relevant to
any kernel with dm-raid support"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
MD: Add del_timer_sync to mddev_suspend (fix nasty panic)
md/raid10: set dev_sectors properly when resizing devices in array.
Pull perf, x86 and scheduler updates from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing: Do not enable function event with enable
perf stat: handle ENXIO error for perf_event_open
perf: Turn off compiler warnings for flex and bison generated files
perf stat: Fix case where guest/host monitoring is not supported by kernel
perf build-id: Fix filename size calculation
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: KVM paravirt kernels don't check for CPUID being unavailable
x86: Fix section annotation of acpi_map_cpu2node()
x86/microcode: Ensure that module is only loaded on supported Intel CPUs
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix KVM and ia64 boot crash due to sched_groups circular linked list assumption
Commit ff9a184c ("ARM: 7400/1: vfp: clear fpscr length and stride bits
on entry to sig handler") flushes the VFP state prior to entering a
signal handler so that a VFP operation inside the handler will trap and
force a restore of ABI-compliant registers. Reflushing and disabling VFP
on the sigreturn path is predicated on the saved thread state indicating
that VFP was used by the handler -- however for SMP platforms this is
only set on context-switch, making the check unreliable and causing VFP
register corruption in userspace since the register values are not
necessarily those restored from the sigframe.
This patch unconditionally flushes the VFP state after a signal handler.
Since we already perform the flush before the handler and the flushing
itself happens lazily, the redundant flush when VFP is not used by the
handler is essentially a nop.
Reported-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A zero value for prot_sect in the memory types table implies that
section mappings should never be created for the memory type in question.
This is checked for in alloc_init_section().
With LPAE, we set a bit to mask access flag faults for kernel mappings.
This breaks the aforementioned (!prot_sect) check in alloc_init_section().
This patch fixes this bug by first checking for a non-zero
prot_sect before setting the PMD_SECT_AF flag.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__napi_schedule might raise softirq but nothing
causes do_softirq to trigger, so it does not in fact
run. As a result,
the error message "NOHZ: local_softirq_pending 08"
sometimes occurs during boot of a KVM guest when the network service is
started and we are oom:
...
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0...NOHZ: local_softirq_pending 08
done.
[ OK ]
...
Further, receive queue processing might get delayed
indefinitely until some interrupt triggers:
virtio_net expected napi to be run immediately.
One way to cause do_softirq to be executed is by
invoking local_bh_enable(). As __napi_schedule is
normally called from bh or irq context, this
seems to make sense: disable bh before __napi_schedule
and enable afterwards.
In fact it's a very complicated way of calling do_softirq(),
and works since this function is only used when we are not
in interrupt context. It's not hot at all, in any ideal scenario.
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Tested-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
When the balloon module is removed, we deflate the balloon, reclaiming
all the pages that were given to the host. However, we don't update the
config values for the new balloon size, resulting in the host showing
outdated balloon values.
The size update is done after each leak and fill operation, only the
module removal case was left out.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If a port was open before going into one of the sleep states, the port
can continue normal operation after restore. However, the host has to
be told that the guest side of the connection is open to restore
pre-suspend state.
This wasn't noticed so far due to a bug in qemu that was fixed recently
(which marked the guest-side connection as always open).
CC: stable@vger.kernel.org # Only for 3.3
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
the old codes will cause 3.4 kernel warning as irq domain size is wrong:
------------[ cut here ]------------
WARNING: at kernel/irq/irqdomain.c:74 irq_domain_legacy_revmap+0x24/0x48()
Modules linked in:
[<c0013f50>] (unwind_backtrace+0x0/0xf8) from [<c001e7d8>] (warn_slowpath_common+0x54/0x64)
[<c001e7d8>] (warn_slowpath_common+0x54/0x64) from [<c001e804>] (warn_slowpath_null+0x1c/0x24)
[<c001e804>] (warn_slowpath_null+0x1c/0x24) from [<c005c3c4>] (irq_domain_legacy_revmap+0x24/0x48)
[<c005c3c4>] (irq_domain_legacy_revmap+0x24/0x48) from [<c005c704>] (irq_create_mapping+0x20/0x120)
[<c005c704>] (irq_create_mapping+0x20/0x120) from [<c005c880>] (irq_create_of_mapping+0x7c/0xf0)
[<c005c880>] (irq_create_of_mapping+0x7c/0xf0) from [<c01a6c48>] (irq_of_parse_and_map+0x2c/0x34)
[<c01a6c48>] (irq_of_parse_and_map+0x2c/0x34) from [<c01a6c68>] (of_irq_to_resource+0x18/0x74)
[<c01a6c68>] (of_irq_to_resource+0x18/0x74) from [<c01a6ce8>] (of_irq_count+0x24/0x34)
[<c01a6ce8>] (of_irq_count+0x24/0x34) from [<c01a7220>] (of_device_alloc+0x58/0x158)
[<c01a7220>] (of_device_alloc+0x58/0x158) from [<c01a735c>] (of_platform_device_create_pdata+0x3c/0x80)
[<c01a735c>] (of_platform_device_create_pdata+0x3c/0x80) from [<c01a7468>] (of_platform_bus_create+0xc8/0x190)
[<c01a7468>] (of_platform_bus_create+0xc8/0x190) from [<c01a74cc>] (of_platform_bus_create+0x12c/0x190)
---[ end trace 1b75b31a2719ed32 ]---
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use del_timer_sync to remove timer before mddev_suspend finishes.
We don't want a timer going off after an mddev_suspend is called. This is
especially true with device-mapper, since it can call the destructor function
immediately following a suspend. This results in the removal (kfree) of the
structures upon which the timer depends - resulting in a very ugly panic.
Therefore, we add a del_timer_sync to mddev_suspend to prevent this.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
raid10 stores dev_sectors in 'conf' separately from the one in
'mddev' because it can have a very significant effect on block
addressing and so need to be updated carefully.
However raid10_resize isn't updating it at all!
To update it correctly, we need to make sure it is a proper
multiple of the chunksize taking various details of the layout
in to account.
This calculation is currently done in setup_conf. So split it
out from there and call it from raid10_resize as well.
Then set conf->dev_sectors properly.
Signed-off-by: NeilBrown <neilb@suse.de>
Pull kvm powerpc fixes from Marcelo Tosatti:
"Urgent KVM PPC updates, quoting Alexander Graf:
There are a few bugs in 3.4 that really should be fixed before
people can be all happy and fuzzy about KVM on PowerPC. These fixes
are:
* fix POWER7 bare metal with PR=y
* fix deadlock on HV=y book3s_64 mode in low memory cases
* fix invalid MMU scope of PR=y mode on book3s_64, possibly eading
to memory corruption"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix bug leading to deadlock in guest HPT updates
powerpc/kvm: Fix VSID usage in 64-bit "PR" KVM
KVM: PPC: Book3S: PR: Fix hsrr code
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Book3S: PR: Handle EMUL_ASSIST
Pull sound fixes from Takashi Iwai:
"A few last-minute regression fixes for 3.4 final kernel. All trivial,
and Cc'ed to stable kernel."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Fix AIF2ADC power down
ALSA: hda/idt - Fix power-map for speaker-pins with some HP laptops
ASoC: cs42l73: Sync digital mixer kcontrols to allow for 0dB
Pull remoteproc fix from Ohad Ben-Cohen:
"Fix a nasty off-by-one remoteproc bug which leaks memory when a remote
processor is shut down and, on certain circumstances, can indirectly
prevent it from being reloaded."
* tag 'rproc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: fix off-by-one bug in __rproc_free_vrings
Pull two Tile arch fixes from Chris Metcalf:
"These are both bug-fixes, one to avoid some issues in how we invoke
the "pending userspace work" flags on return to userspace, and the
other to provide the same signal handler arguments for tilegx32 that
we do for tilegx64."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: apply commit 74fca9da0 to the compat signal handling as well
arch/tile: fix up some issues in calling do_work_pending()
Pull networking tree from David Miller:
1) ptp_pch driver build broke during this merge window due to missing
slab.h header, fix from Geery Uytterhoeven.
2) If ipset passes in a bogus hash table size we crash because the size
is not validated properly. Compounding this, gcc-4.7 can miscompile
ipset such that even when the user specifies legitimate parameters
the tool passes in an out-of-range size to the kernel.
Fix from Jozsef Kadlecsik.
3) Users have reported that the netdev watchdog can trigger with pch_gbe
devices, and it turns out this is happening because of races in the
TX path of the driver leading to the transmitter hanging. Fix from
Eric Dumazet, reported and tested by Andy Cress.
4) Novatel USB551L devices match the generic class entries for the cdc
ethernet USB driver, but they don't work because they have generic
descriptors and thus need FLAG_WWAN to function properly.
Add the necessary ID table entry to fix this, from Dan Williams.
5) A recursive locking fix in the USBNET driver added a new problem, in
that packet list traversal is now racy and we can thus access
unlinked SKBs and crash.
Avoid this situation by adding some extra state tracking, from Ming
Lei.
6) The rtlwifi conversion to asynchronous firmware loading is racy, fix
by reordering the probe procedure. From Larry Finger.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43187
7) Fix regressions with bluetooth keyboards by notifying userland
properly when the security level changes, from Gustavo Padovan.
8) Bluetooth needs to make sure device connected events are emitted
before other kinds of events, otherwise userspace will think there is
no baseband link yet and therefore abort the sockets associated with
that connection.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ipset: fix hash size checking in kernel
ptp_pch: Add missing #include <linux/slab.h>
pch_gbe: fix transmit races
cdc_ether: add Novatel USB551L device IDs for FLAG_WWAN
usbnet: fix skb traversing races during unlink(v2)
Bluetooth: mgmt: Fix device_connected sending order
Bluetooth: notify userspace of security level change
rtlwifi: fix for race condition when firmware is cached
This passes siginfo and mcontext to tilegx32 signal handlers that
don't have SA_SIGINFO set just as we have been doing for tilegx64.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
First, we were at risk of handling thread-info flags, in particular
do_signal(), when returning from kernel space. This could happen
after a failed kernel_execve(), or when forking a kernel thread.
The fix is to test in do_work_pending() for user_mode() and return
immediately if so; we already had this test for one of the flags,
so I just hoisted it to the top of the function.
Second, if a ptraced process updated the callee-saved registers
in the ptregs struct and then processed another thread-info flag, we
would overwrite the modifications with the original callee-saved
registers. To fix this, we add a register to note if we've already
saved the registers once, and skip doing it on additional passes
through the loop. To avoid a performance hit from the couple of
extra instructions involved, I modified the GET_THREAD_INFO() macro
to be guaranteed to be one instruction, then bundled it with adjacent
instructions, yielding an overall net savings.
Reported-By: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The hash size must fit both into u32 (jhash) and the max value of
size_t. The missing checking could lead to kernel crash, bug reported
by Seblu.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/ptp/ptp_pch.c: In function 'pch_remove':
drivers/ptp/ptp_pch.c:576:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
drivers/ptp/ptp_pch.c: In function 'pch_probe':
drivers/ptp/ptp_pch.c:587:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
...and add a "directio" synonym since that's what the manpage has
always advertised.
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'marvell_fixes_for_v3.4' of git://git.infradead.org/users/jcooper/linux:
crypto: mv_cesa requires on CRYPTO_HASH to build
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When handling the H_BULK_REMOVE hypercall, we were forgetting to
invalidate and unlock the hashed page table entry (HPTE) in the case
where the page had been paged out. This fixes it by clearing the
first doubleword of the HPTE in that case.
This fixes a regression introduced in commit a92bce95f0 ("KVM: PPC:
Book3S HV: Keep HPTE locked when invalidating"). The effect of the
regression is that the host kernel will sometimes hang when under
memory pressure.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code forgot to scramble the VSIDs the way we normally do
and was basically using the "proto VSID" directly with the MMU.
This means that in practice, KVM used random VSIDs that could
collide with segments used by other user space programs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: simplify ppc32 case]
Signed-off-by: Alexander Graf <agraf@suse.de>
When jumping back into the kernel to code that knows that it would be
using HSRR registers instead of SRR registers, we need to make sure we
pass it all information on where to jump to in HSRR registers.
Unfortunately, we used r10 to store the information to distinguish between
the HSRR and SRR case. That register got clobbered in between though,
rendering the later comparison invalid.
Instead, let's use cr1 to store this information. That way we don't
need yet another register and everyone's happy.
This fixes PR KVM on POWER7 bare metal for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on a system that is HV capable, some interrupts use HSRR
SPRs instead of the normal SRR SPRs. These are also used in the Linux
handlers to jump back to code after an interrupt got processed.
Unfortunately, in our "jump back to the real host handler after we've
done the context switch" code, we were only setting the SRR SPRs,
rendering Linux to jump back to some invalid IP after it's processed
the interrupt.
This fixes random crashes on p7 opal mode with PR KVM for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
In addition to normal "priviledged instruction" traps, we can also receive
"emulation assist" traps on newer hardware that has the HV bit set.
Handle that one the same way as a privileged instruction, including the
instruction fetching. That way we don't execute old instructions that we
happen to still leave in that field when an emul assist trap comes.
This fixes -M mac99 / -M g3beige on p7 bare metal for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
Due to an errata, the PA7300LC generates a TLB miss interruption even on the
prefetch instruction. This means that prefetch(NULL), which is supposed to be
a nop on linux actually generates a NULL deref fault. Fix this by testing the
address of prefetch against NULL before doing the prefetch.
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As pointed out by serveral people, PA1.1 only has a type 26 instruction
meaning that the space register must be explicitly encoded. Not giving an
explicit space means that the compiler uses the type 24 version which is PA2.0
only resulting in an illegal instruction crash.
This regression was caused by
commit f311847c2f
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Wed Dec 22 10:22:11 2010 -0600
parisc: flush pages through tmpalias space
Reported-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org #2.6.39+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
All PA1.1 systems have been oopsing on boot since
commit f311847c2f
Author: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Wed Dec 22 10:22:11 2010 -0600
parisc: flush pages through tmpalias space
because a PA2.0 instruction was accidentally introduced into the PA1.1 TLB
insertion interruption path when it was consolidated with the do_alias macro.
Fix the do_alias macro only to use PA2.0 instructions if compiled for 64 bit.
Cc: stable@vger.kernel.org #2.6.39+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
John Linville says:
Here are three more fixes that some of my developers are desperate to
see included in 3.4...
Johan Hedberg went to some length justifyng the inclusion of these two
Bluetooth fixes:
"The device_connected fix should be quite self-explanatory, but it's
actually a wider issue than just for keyboards. All profiles that do
incoming connection authorization (e.g. headsets) will break without it
with specific hardware. The reason it wasn't caught earlier is that it
only occurs with specific Bluetooth adapters.
As for the security level patch, this fixes L2CAP socket based security
level elevation during a connection. The HID profile needs this (for
keyboards) and it is the only way to achieve the security level
elevation when using the management interface to talk to the kernel
(hence the management enabling patch being the one that exposes this"
The rtlwifi fix addresses a regression related to firmware loading,
as described in kernel.org bug 43187. It basically just moves a hunk
of code to a more appropriate place.
Signed-off-by: David S. Miller <davem@davemloft.net>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-and-Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-and-Tested-by: Tobias Ulmer <tobiasu@tmux.org>
Tested-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy reported pch_gbe triggered "NETDEV WATCHDOG" errors.
May 11 11:06:09 kontron kernel: WARNING: at net/sched/sch_generic.c:261
dev_watchdog+0x1ec/0x200() (Not tainted)
May 11 11:06:09 kontron kernel: Hardware name: N/A
May 11 11:06:09 kontron kernel: NETDEV WATCHDOG: eth0 (pch_gbe):
transmit queue 0 timed out
It seems pch_gbe has a racy tx path (races with TX completion path)
Remove tx_queue_lock lock since it has no purpose, we must use tx_lock
instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock before unlink, but may
cause skb traversing races:
- after URB is unlinked and the queue lock is released,
the refered skb and skb->next may be moved to done queue,
even be released
- in skb_queue_walk_safe, the next skb is still obtained
by next pointer of the last skb
- so maybe trigger oops or other problems
This patch extends the usage of entry->state to describe 'start_unlink'
state, so always holding the queue(rx/tx) lock to change the state if
the referd skb is in rx or tx queue because we need to know if the
refered urb has been started unlinking in unlink_urbs.
The other part of this patch is based on Huajun's patch:
always traverse from head of the tx/rx queue to get skb which is
to be unlinked but not been started unlinking.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Export handle_edge_irq() and irq_to_desc() to modules to allow them to
do things such as
__irq_set_handler_locked(...., handle_edge_irq);
This fixes
ERROR: "handle_edge_irq" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_to_desc" [drivers/gpio/gpio-pch.ko] undefined!
when gpio-pch is being built as a module.
This was introduced by commit df9541a60a ("gpio: pch9: Use proper flow
type handlers") that added
__irq_set_handler_locked(d->irq, handle_edge_irq);
but handle_edge_irq() was not exported for modules (and inlined
__irq_set_handler_locked() requires irq_to_desc() exported as well)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
6d1d8050b4 "block, partition: add partition_meta_info to hd_struct"
added part_unpack_uuid() which assumes that the passed in buffer has
enough space for sprintfing "%pU" - 37 characters including '\0'.
Unfortunately, b5af921ec0 "init: add support for root devices
specified by partition UUID" supplied 33 bytes buffer to the function
leading to the following panic with stackprotector enabled.
Kernel panic - not syncing: stack-protector: Kernel stack corrupted in: ffffffff81b14c7e
[<ffffffff815e226b>] panic+0xba/0x1c6
[<ffffffff81b14c7e>] ? printk_all_partitions+0x259/0x26xb
[<ffffffff810566bb>] __stack_chk_fail+0x1b/0x20
[<ffffffff81b15c7e>] printk_all_paritions+0x259/0x26xb
[<ffffffff81aedfe0>] mount_block_root+0x1bc/0x27f
[<ffffffff81aee0fa>] mount_root+0x57/0x5b
[<ffffffff81aee23b>] prepare_namespace+0x13d/0x176
[<ffffffff8107eec0>] ? release_tgcred.isra.4+0x330/0x30
[<ffffffff81aedd60>] kernel_init+0x155/0x15a
[<ffffffff81087b97>] ? schedule_tail+0x27/0xb0
[<ffffffff815f4d24>] kernel_thread_helper+0x5/0x10
[<ffffffff81aedc0b>] ? start_kernel+0x3c5/0x3c5
[<ffffffff815f4d20>] ? gs_change+0x13/0x13
Increase the buffer size, remove the dangerous part_unpack_uuid() and
use snprintf() directly from printk_all_partitions().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Szymon Gruszczynski <sz.gruszczynski@googlemail.com>
Cc: Will Drewry <wad@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BIOS on some HP laptops don't set the speaker-pins as fixed but expose
as jacks, and this confuses the driver as if these pins are
jack-detectable. As a result, the machine doesn't get sounds from
speakers because the driver prepares the power-map update via jack
unsol events which never come up in reality. The bug was introduced
in some time in 3.2 for enabling the power-mapping feature.
This patch fixes the problem by replacing the check of the persistent
power-map bits with a proper is_jack_detectable() call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43240
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addresses a bug in a special case for target core SPC-2 RELEASE
logic where the same physical client (eg: iSCSI InitiatorName) with
differing iSCSI session identifiers (ISID) is allowed to incorrectly release
the same client's SPC-2 reservation from the non reservation holding path.
Note this bug is specific to iscsi-target w/ SPC-2 reservations, and
with the default enforce_pr_isids=1 device attr setting in target-core
controls if a InitiatorName + different ISID reservations are handled
the same as a single iSCSI client entity.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Section 15.3.1.2 of the software developer manual has this to say about the
RIPV bit in the IA32_MCG_STATUS register:
RIPV (restart IP valid) flag, bit 0 — Indicates (when set) that program
execution can be restarted reliably at the instruction pointed to by the
instruction pointer pushed on the stack when the machine-check exception
is generated. When clear, the program cannot be reliably restarted at
the pushed instruction pointer.
We need to save the state of this bit in do_machine_check() and use it
in mce_notify_process() to force a signal; even if memory_failure() says
it made a complete recovery ... e.g. replaced a clean LRU page.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull media fixes from Mauro Carvalho Chehab:
"For a some fix patches for v3.4, including a regression fix at DVB core"
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca - sonixj: Fix a zero divide in isoc interrupt
[media] media: videobuf2-dma-contig: include header for exported symbols
[media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
[media] media: vb2-memops: Export vb2_get_vma symbol
[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
[media] s5p-fimc: Fix locking in subdev set_crop op
[media] dvb_frontend: fix a regression with DVB-S zig-zag
[media] fintek-cir: change || to &&
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
[media] rc: Postpone ISR registration
[media] marvell-cam: fix an ARM build error
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
Pull networking fixes from David Miller:
"The main purpose of this pull request is to fix up the erroneous
bonding patch I applied last round. I meant to apply v4 of the patch
from Jiri but I applied v3 by accident. Mea culpa.
Also, eagle eyed Dan Carpenter noticed that openvswitch has one of
those "X = alloc(); if (!Y)" mistakes, test the proper pointer
instead."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
The mgmt_ev_device_connected signal must be sent before any event
indications happen for sockets associated with the connection. Otherwise
e.g. device authorization for the sockets will fail with ENOTCONN as
user space things that there is no baseband link.
This patch fixes the issue by ensuring that the device_connected event
if sent (if it hasn't been so already) as soon as the first ACL data
packet arrives from the remote device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It fixes L2CAP socket based security level elevation during a
connection. The HID profile needs this (for keyboards) and it is the only
way to achieve the security level elevation when using the management
interface to talk to the kernel (hence the management enabling patch
being the one that exposes this issue).
It enables the userspace a security level change when the socket is
already connected and create a way to notify the socket the result of the
request. At the moment of the request the socket is made non writable, if
the request fails the connections closes, otherwise the socket is made
writable again, POLL_OUT is emmited.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
flowctrl_write_cpu_csr uses the cpu halt offsets and vice versa. This patch
fixes this bug.
Reported-by: Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[swarren: This problem was introduced in v3.4-rc1, in commit 26fe681 "ARM:
tegra: functions to access the flowcontroller", when this file was first
added]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
I see builds failing with:
CC [M] drivers/mmc/host/dw_mmc.o
In file included from drivers/mmc/host/dw_mmc.c:15:
include/linux/blkdev.h:1404: warning: 'struct task_struct' declared inside parameter list
include/linux/blkdev.h:1404: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/blkdev.h:1408: warning: 'struct task_struct' declared inside parameter list
include/linux/blkdev.h:1413: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'blk_needs_flush_plug'
make[4]: *** [drivers/mmc/host/dw_mmc.o] Error 1
This is because dw_mmc.c includes linux/blkdev.h as the very first file,
and when CONFIG_BLOCK=n, blkdev.h omits all includes.
As it requires linux/sched.h even when CONFIG_BLOCK=n, move this out of
the #ifdef.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix a nasty off-by-one bug in __rproc_free_vrings which
resulted in a memory leak and (for some platforms) failures
to reload the remote processor.
Signed-off-by: Subramaniam Chanderashekarapuram <subramaniam.ca@ti.com>
[ohad@wizery.com: reword commit log, stick with the for loop]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
"skb" is non-NULL here, for example we dereference it in skb_clone().
The intent was to test "nskb" which was just set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8cd ("bonding: don't increase
rx_dropped after processing LACPDUs")
I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.
This inter-diffs such that the warnings are now gone.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.
Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.
Pull networking fixes from David S. Miller:
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."
* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
Since cpufreq has no official maintainer at the moment, I'm willing
to maintain it along some other power management core code I've been
maintaining already.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vfp_enable function enables access to the VFP co-processor register
space (cp10 and cp11) on the current CPU and must be called with
preemption disabled. Unfortunately, the vfp_init late initcall does not
disable preemption and can lead to an oops during boot if thread
migration occurs at the wrong time and we end up attempting to access
the FPSID on a CPU with VFP access disabled.
This patch fixes the initcall to call vfp_enable from a non-preemptible
context on each CPU and adds a BUG_ON(preemptible) to ensure that any
similar problems are easily spotted in the future.
Cc: stable@vger.kernel.org
Reported-by: Hyungwoo Yang <hwoo.yang@gmail.com>
Signed-off-by: Hyungwoo Yang <hyungwooy@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix two places in commit 104655fd4d ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.
Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:
WARNING: at lib/list_debug.c:32 __list_add+0x8f/0xa0()
...
list_add corruption. next->prev should be prev (ffff880323b96140), but was ffff8801d2c48440. (next=ffff8801d2c485c0).
...
Pid: 17205, comm: kworker/u:1 Tainted: G W O 3.4.0-rc3.snitm+ #1
Call Trace:
[<ffffffff8103ca1f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103cb16>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa04f6ce6>] ? bio_detain+0xc6/0x210 [dm_thin_pool]
[<ffffffff8124ff3f>] __list_add+0x8f/0xa0
[<ffffffffa04f70d2>] process_discard+0x2a2/0x2d0 [dm_thin_pool]
[<ffffffffa04f6a78>] ? remap_and_issue+0x38/0x50 [dm_thin_pool]
[<ffffffffa04f7c3b>] process_deferred_bios+0x7b/0x230 [dm_thin_pool]
[<ffffffffa04f7df0>] ? process_deferred_bios+0x230/0x230 [dm_thin_pool]
[<ffffffffa04f7e42>] do_worker+0x52/0x60 [dm_thin_pool]
[<ffffffff81056fa9>] process_one_work+0x129/0x450
[<ffffffff81059b9c>] worker_thread+0x17c/0x3c0
[<ffffffff81059a20>] ? manage_workers+0x120/0x120
[<ffffffff8105eabe>] kthread+0x9e/0xb0
[<ffffffff814ceda4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105ea20>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff814ceda0>] ? gs_change+0x13/0x13
---[ end trace 7e0a523bc5e52692 ]---
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit
6f94a4c45a ("dm thin: fix stacked bi_next
usage").
A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull GPIO omap bug fix from Grant Likely.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/omap: fix incorrect initialization of omap_gpio_mod_init
Pull another powerpc irq fix from Benjamin Herrenschmidt:
"It looks like my previous fix for the lazy irq masking problem wasn't
quite enough. There was another problem related to performance
monitor interrupts acting as NMIs leaving the flags in an incorrect
state. Here's a fix that finally seems to make perf solid again."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.
That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.
This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.
This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.
This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take vlan header length into account, when vlan id is stored as
vlan_tci. Otherwise tagged packets coming from macvtap will be
truncated.
Signed-off-by: Basil Gor <basil.gor@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some potentially problematic legacy code within
core_clear_initiator_node_from_tpg() that was originally intended to
release left over se_lun_acl setup during dynamic NodeACL+MappedLUN
generate when running with TPG demo-mode operation.
Since we now only ever expect to allocate and release se_lun_acl from
within target_core_fabric_configfs.c:target_fabric_make_mappedlun() and
target_fabric_drop_mappedlun() context respectively, this code for
demo-mode release is incorrect and needs to be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull a m68knommu fix from Greg Ungerer:
"It contains a single fix for including the ColdFire QSPI interface
setup code when enabled as a module. This was broken in the
consolidation of the ColdFire SoC device tables in the 3.4 merge
window."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable qspi support when SPI_COLDFIRE_QSPI = m
Why is there less MemFree than there used to be? It perturbed a test,
so I've just been bisecting linux-next, and now find the offender went
upstream yesterday.
Commit 93278814d3 "mm: fix division by 0 in percpu_pagelist_fraction()"
mistakenly initialized percpu_pagelist_fraction to the sysctl's minimum 8,
which leaves 1/8th of memory on percpu lists (on each cpu??); but most of
us expect it to be left unset at 0 (and it's not then used as a divisor).
MemTotal: 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB
Repetitive test with percpu_pagelist_fraction 8:
MemFree: 6948420kB 6237172kB 6949696kB 6840692kB 6949048kB 6862984kB
Same test with percpu_pagelist_fraction back to 0:
MemFree: 7945000kB 7944908kB 7948568kB 7949060kB 7948796kB 7948812kB
Signed-off-by: Hugh Dickins <hughd@google.com>
[ We really should fix the crazy sysctl interface too, but that's a
separate thing - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The number of bio_get_nr_vecs() is passed down via bio_alloc() to
bvec_alloc_bs(), which fails the bio allocation if
nr_iovecs > BIO_MAX_PAGES. For the underlying caller this causes an
unexpected bio allocation failure.
Limiting to queue_max_segments() is not sufficient, as max_segments
also might be very large.
bvec_alloc_bs(gfp_mask, nr_iovecs, ) => NULL when nr_iovecs > BIO_MAX_PAGES
bio_alloc_bioset(gfp_mask, nr_iovecs, ...)
bio_alloc(GFP_NOIO, nvecs)
xfs_alloc_ioend_bio()
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hi,
We have a bug report open where a squashfs image mounted on ppc64 would
exhibit errors due to trying to read beyond the end of the disk. It can
easily be reproduced by doing the following:
[root@ibm-p750e-02-lp3 ~]# ls -l install.img
-rw-r--r-- 1 root root 142032896 Apr 30 16:46 install.img
[root@ibm-p750e-02-lp3 ~]# mount -o loop ./install.img /mnt/test
[root@ibm-p750e-02-lp3 ~]# dd if=/dev/loop0 of=/dev/null
dd: reading `/dev/loop0': Input/output error
277376+0 records in
277376+0 records out
142016512 bytes (142 MB) copied, 0.9465 s, 150 MB/s
In dmesg, you'll find the following:
squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 43.106012] attempt to access beyond end of device
[ 43.106029] loop0: rw=0, want=277410, limit=277408
[ 43.106039] Buffer I/O error on device loop0, logical block 138704
[ 43.106053] attempt to access beyond end of device
[ 43.106057] loop0: rw=0, want=277412, limit=277408
[ 43.106061] Buffer I/O error on device loop0, logical block 138705
[ 43.106066] attempt to access beyond end of device
[ 43.106070] loop0: rw=0, want=277414, limit=277408
[ 43.106073] Buffer I/O error on device loop0, logical block 138706
[ 43.106078] attempt to access beyond end of device
[ 43.106081] loop0: rw=0, want=277416, limit=277408
[ 43.106085] Buffer I/O error on device loop0, logical block 138707
[ 43.106089] attempt to access beyond end of device
[ 43.106093] loop0: rw=0, want=277418, limit=277408
[ 43.106096] Buffer I/O error on device loop0, logical block 138708
[ 43.106101] attempt to access beyond end of device
[ 43.106104] loop0: rw=0, want=277420, limit=277408
[ 43.106108] Buffer I/O error on device loop0, logical block 138709
[ 43.106112] attempt to access beyond end of device
[ 43.106116] loop0: rw=0, want=277422, limit=277408
[ 43.106120] Buffer I/O error on device loop0, logical block 138710
[ 43.106124] attempt to access beyond end of device
[ 43.106128] loop0: rw=0, want=277424, limit=277408
[ 43.106131] Buffer I/O error on device loop0, logical block 138711
[ 43.106135] attempt to access beyond end of device
[ 43.106139] loop0: rw=0, want=277426, limit=277408
[ 43.106143] Buffer I/O error on device loop0, logical block 138712
[ 43.106147] attempt to access beyond end of device
[ 43.106151] loop0: rw=0, want=277428, limit=277408
[ 43.106154] Buffer I/O error on device loop0, logical block 138713
[ 43.106158] attempt to access beyond end of device
[ 43.106162] loop0: rw=0, want=277430, limit=277408
[ 43.106166] attempt to access beyond end of device
[ 43.106169] loop0: rw=0, want=277432, limit=277408
...
[ 43.106307] attempt to access beyond end of device
[ 43.106311] loop0: rw=0, want=277470, limit=2774
Squashfs manages to read in the end block(s) of the disk during the
mount operation. Then, when dd reads the block device, it leads to
block_read_full_page being called with buffers that are beyond end of
disk, but are marked as mapped. Thus, it would end up submitting read
I/O against them, resulting in the errors mentioned above. I fixed the
problem by modifying init_page_buffers to only set the buffer mapped if
it fell inside of i_size.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Nick Piggin <npiggin@kernel.dk>
--
Changes from v1->v2: re-used max_block, as suggested by Nick Piggin.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Release the semaphore in an error path in mtip_hw_get_scatterlist(). This
fixes the smatch warning inconsistent returns.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The variables 'StatusProcEntry' and 'UserCommandProcEntry' are
assigned to once and then never used. This patch gets rid of the
variables.
While I was there I also fixed the indentation of the function to use
tabs rather than spaces for the lines that did not already do so.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
the cookie updates completed the cyclic dma descriptor wrongly. This caused the
BUG_ON to be hit as submit is called for completed descriptor
Fix this by not marking the cyclic descriptor as complete
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.
Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.
In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).
Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.
In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.
Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.
The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).
To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yaseivch <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.
Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.
The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the caller (PM resume code) is not the one holding rtnl, when taking the
'else' branch rtnl may be released at any moment, thereby defeating the whole
purpose of this code block.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge PA-RISC compile fixes from Rolf Eike Beer:
"Since commit d66acc39c7 ("bitops: Optimise get_order()") getorder.h
includes log2.h which leads to an include loop on PA-RISC, bringing a
bunch of other breakage to light. This patchset fixes the compilation
of the current state of 3.4 on HPPA.
Unchanged against the first version, just added an Ack by Grant."
* emailed from Rolf Eike Beer <eike-kernel@sf-tec.de>: (5 patches)
parisc: move definition of PAGE0 to asm/page.h
parisc: add missing include of asm/page.h to asm/pgtable.h
parisc: drop include of asm/pdc.h from asm/hardware.h
parisc: add missing forward declarations in asm/hardware.h
parisc: add missing includes in asm/spinlock.h
Merge misc fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
MAINTAINERS: add maintainer for LED subsystem
mm: nobootmem: fix sign extend problem in __free_pages_memory()
drivers/leds: correct __devexit annotations
memcg: free spare array to avoid memory leak
namespaces, pid_ns: fix leakage on fork() failure
hugetlb: prevent BUG_ON in hugetlb_fault() -> hugetlb_cow()
mm: fix division by 0 in percpu_pagelist_fraction()
proc/pid/pagemap: correctly report non-present ptes and holes between vmas
This was defined in asm/pdc.h which needs to include asm/page.h for
__PAGE_OFFSET. This leads to an include loop so that page.h eventually will
include pdc.h again. While this is no problem because of header guards, it is
a problem because some symbols may be undefined. Such an error is this:
In file included from include/linux/bitops.h:35:0,
from include/asm-generic/getorder.h:7,
from arch/parisc/include/asm/page.h:162,
from arch/parisc/include/asm/pdc.h:346,
from arch/parisc/include/asm/processor.h:16,
from arch/parisc/include/asm/spinlock.h:6,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from include/linux/sysfs.h:20,
from include/linux/kobject.h:21,
from include/linux/device.h:17,
from include/linux/eisa.h:5,
from arch/parisc/kernel/pci.c:11:
arch/parisc/include/asm/bitops.h: In function ‘set_bit’:
arch/parisc/include/asm/bitops.h:82:2: error: implicit declaration of function ‘_atomic_spin_lock_irqsave’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/bitops.h:84:2: error: implicit declaration of function ‘_atomic_spin_unlock_irqrestore’ [-Werror=implicit-function-declaration]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes these errors:
In file included from arch/parisc/include/asm/io.h:5:0,
from include/linux/io.h:22,
from include/linux/pci.h:54,
from arch/parisc/kernel/setup.c:35:
arch/parisc/include/asm/pgtable.h:92:6: warning: "PAGE_SHIFT" is not defined [-Wundef]
arch/parisc/include/asm/pgtable.h:92:6: warning: "PAGE_SHIFT" is not defined [-Wundef]
arch/parisc/include/asm/pgtable.h:92:6: warning: "BITS_PER_PTE_ENTRY" is not defined [-Wundef]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems none of the symbols defined by pdc.h is needed, but it introduces an
include loop causing compile errors:
In file included from arch/parisc/include/asm/spinlock.h:4:0,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:56,
from include/linux/bitops.h:35,
from include/asm-generic/getorder.h:7,
from arch/parisc/include/asm/page.h:162,
from arch/parisc/include/asm/pdc.h:346,
from arch/parisc/include/asm/hardware.h:5,
from arch/parisc/kernel/hardware.c:30:
arch/parisc/include/asm/processor.h:74:16: error: field ‘cpu_type’ has incomplete type
arch/parisc/include/asm/processor.h:77:20: error: field ‘model’ has incomplete type
arch/parisc/include/asm/processor.h: In function ‘parisc_requires_coherency’:
arch/parisc/include/asm/processor.h:349:36: error: ‘mako’ undeclared (first use in this function)
arch/parisc/include/asm/processor.h:349:36: note: each undeclared identifier is reported only once for each function it appears in
arch/parisc/include/asm/processor.h:350:30: error: ‘mako2’ undeclared (first use in this function)
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Grant Grundler <grantgrundler@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes this warnings:
In file included from arch/parisc/include/asm/processor.h:15:0,
from arch/parisc/include/asm/spinlock.h:4,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:11,
from include/linux/bitops.h:22,
from include/linux/kernel.h:19,
from include/linux/sched.h:55,
from arch/parisc/kernel/asm-offsets.c:31:
arch/parisc/include/asm/hardware.h:106:10: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:106:10: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/parisc/include/asm/hardware.h:116:59: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:118:47: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:119:57: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This leads to this errors:
In file included from arch/parisc/include/asm/atomic.h:20:0,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:56,
from include/linux/bitops.h:22,
from include/linux/kernel.h:19,
from include/linux/sched.h:55,
from arch/parisc/kernel/asm-offsets.c:31:
arch/parisc/include/asm/spinlock.h: In function ‘arch_spin_is_locked’:
arch/parisc/include/asm/spinlock.h:9:2: error: implicit declaration of function ‘__ldcw_align’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/spinlock.h:9:29: warning: initialization makes pointer from integer without a cast [enabled by default]
arch/parisc/include/asm/spinlock.h: In function ‘arch_spin_lock_flags’:
arch/parisc/include/asm/spinlock.h:22:2: error: implicit declaration of function ‘mb’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/spinlock.h:23:4: warning: assignment makes pointer from integer without a cast [enabled by default]
arch/parisc/include/asm/spinlock.h:24:2: error: implicit declaration of function ‘__ldcw’ [-Werror=implicit-function-declaration]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull a sparc fix from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Do not clobber %g2 in xcall_fetch_glob_regs().
Commit 66aebce747 ("hugetlb: fix race condition in hugetlb_fault()")
added code to avoid a race condition by elevating the page refcount in
hugetlb_fault() while calling hugetlb_cow().
However, one code path in hugetlb_cow() includes an assertion that the
page count is 1, whereas it may now also have the value 2 in this path.
The consensus is that this BUG_ON has served its purpose, so rather than
extending it to cover both cases, we just remove it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Hillf Danton <dhillf@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.0.29+, 3.2.16+, 3.3.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu_pagelist_fraction_sysctl_handler() has only considered -EINVAL as
a possible error from proc_dointvec_minmax().
If any other error is returned, it would proceed to divide by zero since
percpu_pagelist_fraction wasn't getting initialized at any point. For
example, writing 0 bytes into the proc file would trigger the issue.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull percpu fixes from Tejun Heo:
"This pull request contains two patches. One is kmemleak annotation
fix which isn't critical. The other is kinda serious.
Depending on NUMA topology, percpu allocator may end up assigning
overlapping regions for the static percpu areas for different CPUs.
While critical, the bug has been there for a very long time and only
few configurations seem to be affected (NUMA configurations w/ no
memory nodes for example) - so, while it's critical, it isn't exactly
urgent."
* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
kmemleak: Fix the kmemleak tracking of the percpu areas with !SMP
percpu: pcpu_embed_first_chunk() should free unused parts after all allocs are complete
With the adding of function tracing event to perf, it caused a
side effect that produces the following warning when enabling all
events in ftrace:
# echo 1 > /sys/kernel/debug/tracing/events/enable
[console]
event trace: Could not enable event function
This is because when enabling all events via the debugfs system
it ignores events that do not have a ->reg() function assigned.
This was to skip over the ftrace internal events (as they are
not TRACE_EVENTs). But as the ftrace function event now has
a ->reg() function attached to it for use with perf, it is no
longer ignored.
Worse yet, this ->reg() function is being called when it should
not be. It returns an error and causes the above warning to
be printed.
By adding a new event_call flag (TRACE_EVENT_FL_IGNORE_ENABLE)
and have all ftrace internel event structures have it set,
setting the events/enable will no longe try to incorrectly enable
the function event and does not warn.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
%g2 is meant to hold the CPUID number throughout this routine, since
at the very beginning, and at the very end, we use %g2 to calculate
indexes into per-cpu arrays.
However we erroneously clobber it in order to hold the %cwp register
value mid-stream.
Fix this code to use %g3 for the %cwp read and related calulcations
instead.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull a NFS client bugfix from Trond Myklebust:
"Fix for the NFSv4 security negotiation: ensure that the security
negotiation tries all registered security flavours"
* tag 'nfs-for-3.4-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
auth_gss: the list of pseudoflavors not being parsed correctly
Pull sound fixes from Takashi Iwai:
"Slightly more than expected as rc7, but all are reasonablly small
fixes. A few additions of HD-audio fixup entries, a couple of other
regression fixes including a revert, and a few other trivial
oneliners."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: sh: fix migor.c compilation
ALSA: HDA: Lessen CPU usage when waiting for chip to respond
Revert "ALSA: hda - Set codec to D3 forcibly even if not used"
ALSA: hda/realtek - Call alc_auto_parse_customize_define() always after fixup
ALSA: hdsp - Provide ioctl_compat
ALSA: hda/realtek - Add missing CD-input pin for MSI-7350 mobo
ALSA: hda/realtek - Add a fixup for Acer Aspire 5739G
ALSA: echoaudio: Remove incorrect part of assertion
compat_sys_sigprocmask reads a smaller signal mask from userspace than
sigprogmask accepts for setting. So the high word of blocked.sig[0]
will be cleared, releasing any potentially blocked RT signal.
This was discovered via userspace code that relies on get/setcontext.
glibc's i386 versions of those functions use sigprogmask instead of
rt_sigprogmask to save/restore signal mask and caused RT signal
unblocking this way.
As suggested by Linus, this replaces the sys_sigprocmask based compat
version with one that open-codes the required logic, including the merge
of the existing blocked set with the new one provided on SIG_SETMASK.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.
Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.
Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.
Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix a use-after-free in the TMF path, where cmd may have been already
freed by virtscsi_complete_free when wait_for_completion restarts
executing virtscsi_tmf. Technically a race, but in practice the command
will always be freed long before the completion waiter is awoken.
The fix is to make callers specifying a completion responsible for
freeing the command in all cases.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 6f381fa344
Author: Lin Ming <ming.m.lin@intel.com>
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
Caused a regression where we oops in every legacy mode SCSI host driver
because they supply a NULL pointer to scsi_add_host(). Fix this by checking
for the NULL in scsi_add_host_with_dma() and changing the DMA device to being
the platform_bus in that case (which replicates the original behaviour).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This test is always true so it means we revalidate the length every
time, which generates more network traffic. When it is SEEK_SET or
SEEK_CUR, then we don't need to revalidate.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull ARM: SoC fixes from Olof Johansson:
"Things have slowed down a lot for us, but we have five more fixes for
omap and kirkwood below. Three are for boards setup issues, two are
SoC-level fixes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: igep0020: fix smsc911x dummy regulator id
ARM: orion5x: Fix GPIO enable bits for MPP9
ARM: kirkwood: add missing kexec.h include
ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler
Pull last minute regman bug fix from Mark Brown:
"This is a last minute bug fix that was only just noticed since the
code path that's being exercised here is one that is fairly rarely
used. The changelog for the change itself is extremely clear and the
code itself is obvious to inspection so should be pretty safe."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix possible memory corruption in regmap_bulk_read()
Pull KVM fixes from Avi Kivity:
"Two asynchronous page fault fixes (one guest, one host), a powerpc
page refcount fix, and an ia64 build fix."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: ia64: fix build due to typo
KVM: PPC: Book3S HV: Fix refcounting of hugepages
KVM: Do not take reference to mm during async #PF
KVM: ensure async PF event wakes up vcpu from halt
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a couple of last minute fixes for 3.4 for regressions
introduced by my rewrite of the lazy irq masking code."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/irq: Make alignment & program interrupt behave the same
powerpc/irq: Fix bug with new lazy IRQ handling code
perf stat on PPC currently fails to run:
$ perf stat -- sleep 1
Error: open_counter returned with 6 (No such device or address). /bin/dmesg may provide additional information.
Fatal: Not all events could be opened.
The problem is that until 2.6.37 (behavior changed with commit b0a873e)
perf on PPC returns ENXIO when hw_perf_event_init() fails. With this
patch we get the expected behavior:
$ perf stat -v -- sleep 1
cycles event is not supported by the kernel.
stalled-cycles-frontend event is not supported by the kernel.
stalled-cycles-backend event is not supported by the kernel.
instructions event is not supported by the kernel.
branches event is not supported by the kernel.
branch-misses event is not supported by the kernel.
...
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1336490956-57145-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kmemleak tracks the percpu allocations via a specific API and the
originally allocated areas must be removed from kmemleak (via
kmemleak_free). The code was already doing this for SMP systems.
Reported-by: Sami Liedes <sami.liedes@iki.fi>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
pcpu_embed_first_chunk() allocates memory for each node, copies percpu
data and frees unused portions of it before proceeding to the next
group. This assumes that allocations for different nodes doesn't
overlap; however, depending on memory topology, the bootmem allocator
may end up allocating memory from a different node than the requested
one which may overlap with the portion freed from one of the previous
percpu areas. This leads to percpu groups for different nodes
overlapping which is a serious bug.
This patch separates out copy & partial free from the allocation loop
such that all allocations are complete before partial frees happen.
This also fixes overlapping frees which could happen on allocation
failure path - out_free_areas path frees whole groups but the groups
could have portions freed at that point.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: "Pavel V. Panteleev" <pp_84@mail.ru>
Tested-by: "Pavel V. Panteleev" <pp_84@mail.ru>
LKML-Reference: <E1SNhwY-0007ui-V7.pp_84-mail-ru@f220.mail.ru>
Fix two board spefific regressions and one regression caused by bad documentation
By Archit Taneja (1) and others
via Tony Lindgren
* tag 'omap-fixes-for-v3.4-rc6-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: igep0020: fix smsc911x dummy regulator id
ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler
id 0 is already used and causes errors at boot:
WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'
Fix it by using the next available one (id=1).
This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.
Signed-off-by: Enrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.
Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.
I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:
[ 5.438589] regmap_bulk_read after regamp_read() for register 122
[ 5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.467535] regmap_bulk_read after regamp_read() for register 123
[ 5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.496425] regmap_bulk_read after regamp_read() for register 124
[ 5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.525372] regmap_bulk_read after regamp_read() for register 125
[ 5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 126
[ 5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 127
[ 5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001
Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we have one cpu that failed to boot and boot cpu gave up on
waiting for it and then another cpu is being booted, kernel
might crash with following OOPS:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff812c3630>] __bitmap_weight+0x30/0x80
Call Trace:
[<ffffffff8108b9b6>] build_sched_domains+0x7b6/0xa50
The crash happens in init_sched_groups_power() that expects
sched_groups to be circular linked list. However it is not
always true, since sched_groups preallocated in __sdt_alloc are
initialized in build_sched_groups and it may exit early
if (cpu != cpumask_first(sched_domain_span(sd)))
return 0;
without initializing sd->groups->next field.
Fix bug by initializing next field right after sched_group was
allocated.
Also-Reported-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Cc: a.p.zijlstra@chello.nl
Cc: pjt@google.com
Cc: seto.hidetoshi@jp.fujitsu.com
Link: http://lkml.kernel.org/r/1336559908-32533-1-git-send-email-imammedo@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When an IRQ for some reason gets lost, we wait up to a second using
udelay, which is CPU intensive. This patch improves the situation by
waiting about 30 ms in the CPU intensive mode, then stepping down to
using msleep(2) instead. In essence, we trade some granularity in
exchange for less CPU consumption when the waiting time is a bit longer.
As a result, PulseAudio should no longer be killed by the kernel
for taking up to much RT-prio CPU time. At least not for *this* reason.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Tested-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By Ben Hutchings (1) and Ian Campbell (1)
via Jason Cooper: "ARM: kirkwood: fixes for v3.4"
* 'kirkwood_fixes_for_v3.4' of git://git.infradead.org/users/jcooper/linux-kirkwood:
ARM: orion5x: Fix GPIO enable bits for MPP9
ARM: kirkwood: add missing kexec.h include
Alignment was the last user of the ENABLE_INTS macro, which we can
now remove. All non-syscall exceptions now disable interrupts on
entry, they get re-enabled conditionally from C code. Don't
unconditionally re-enable in program check either, check the
original context.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had a case where we could turn on hard interrupts while
leaving the PACA_IRQ_HARD_DIS bit set in the PACA. This can
in turn cause a BUG_ON() to hit in __check_irq_replay() due
to interrupt state getting out of sync.
The assembly code was also way too convoluted. Instead, we
now leave it to the C code to do the right thing which ends
up being smaller and more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The r8169 may get stuck or show bad behaviour after activating TSO :
the net_device is not stopped when it has no more TX descriptors.
This problem comes from TX_BUFS_AVAIL which may reach -1 when all
transmit descriptors are in use. The patch simply tries to keep positive
values.
Tested with 8111d(onboard) on a D510MO, and with 8111e(onboard) on a
Zotac 890GXITX.
Signed-off-by: Julien Ducourthial <jducourt@free.fr>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to request_mem_region() has been introduced in the omap-gpio
driver recently (commit 96751fcbe5,
"gpio/omap: Use devm_ API and add request_mem_region"). This change
prevented the Amstrad Delta NAND driver, which was doing the same in
order to take control over OMAP MPU I/O lines that the NAND device hangs
off, from loading successfully.
The I/O lines and corresponding registers used by the NAND driver are a
subset of those used for the GPIO function. Then, to avoid run time
collisions, all MPUIO GPIO lines should be marked as requested while
initializing the NAND driver, and vice versa, a single MPUIO GPIO line
already requested before the NAND driver initialization is attempted
should prevent the NAND device from being started successfully.
There is another driver, omap-keypad, which also manipulates MPUIO
registers, but has never been calling request_mem_region() on startup,
so it's not affected by the change in the gpio-omap and works correctly.
It uses the depreciated omap_read/write functions for accessing MPUIO
registers. Unlike the NAND driver, these I/O lines and registers are
separate from those used by the GPIO driver. However, both register sets
are non-contiguous and overlapping, so it would be impractical to
request the two sets separately, one from the gpio-omap, the other form
the omap-keypad driver.
In order to solve all these issues correctly, a solution first suggested
by Artem Bityutskiy, then closer specified by Tony Lindgren while they
commented the initial version of this fix, should be implemented. The
gpio-omap driver should export a few functions which would allow the
other two drivers to access MPUIO registers in a safe manner instead of
trying to manage them in parallel to the GPIO driver. However, such a
big change, affecting 3 drivers all together, is not suitable for the rc
cycle, and should be prepared for the merge window. Then, an
alternative solution is proposed as a regression fix.
For the ams-delta NAND driver to initialize correctly in coexistence
with the changed GPIO driver, drop the request_mem_region() call from
the former, especially as this call is going to be removed while the
long-term solution is implemented.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 554cdaefd1 ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only). For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:
[ 12.711476] leds-gpio: probe of leds-gpio failed with error -22
Reported-by: Henry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [v3.0+]
Tested-by: Hans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull regulator fixes from Mark Brown:
"One small fix for an edge condition in the max8997 driver and a fix
for a surprise in the devres API which caused devm_regulator_put() to
not actually put the regulator - a nicer version of this based on an
improvement of the devres API is queued for 3.5."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Actually free the regulator in devm_regulator_put()
regulator: Fix the logic to ensure new voltage setting in valid range
Fixes the following build error when CONFIG_KEXEC is enabled:
CC arch/arm/mach-kirkwood/board-dt.o
arch/arm/mach-kirkwood/board-dt.c: In function 'kirkwood_dt_init':
arch/arm/mach-kirkwood/board-dt.c:52:2: error: 'kexec_reinit' undeclared (first use in this function)
arch/arm/mach-kirkwood/board-dt.c:52:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
[v4, rebase onto recent Linus for repost]
[v3, speak actual English in the commit message, thanks Sergei Shtylyov]
[v2, using linux/kexec.h not asm/kexec.h]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull drm fixes from Dave Airlie:
"Two fixes from Intel, one a regression, one because I merged an early
version of a fix.
Also the nouveau revert of the i2c code that was tested on the list."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/i2c: resume use of i2c-algo-bit, rather than custom stack
drm/i915: Do no set Stencil Cache eviction LRA w/a on gen7+
drm/i915: disable sdvo hotplug on i945g/gm
Pull xen fixes from Konrad Rzeszutek Wilk:
- fix to Kconfig to make it fit within 80 line characters,
- two bootup fixes (AMD 8-core and with PCI BIOS),
- cleanup code in a Xen PV fb driver,
- and a crash fix when trying to see non-existent PTE's
* tag 'stable/for-linus-3.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/Kconfig: fix Kconfig layout
xen/pci: don't use PCI BIOS service for configuration space accesses
xen/pte: Fix crashes when trying to see non-existent PGD/PMD/PUD/PTEs
xen/apic: Return the APIC ID (and version) for CPU 0.
drivers/video/xen-fbfront.c: add missing cleanup code
Pull two percpu fixes from Tejun Heo:
"One adds missing KERN_CONT on split printk()s and the other makes
the percpu allocator avoid using PMD_SIZE as atom_size on x86_32.
Using PMD_SIZE led to vmalloc area exhaustion on certain
configurations (x86_32 android) and the only cost of using PAGE_SIZE
instead is static percpu area not being aligned to large page
mapping."
* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit
percpu: use KERN_CONT in pcpu_dump_alloc_info()
Pull ARM fixes from Russell King:
"This is mainly audit fixes, found by folks who happened to enable this
feature and then found it broke their user applications."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7414/1: SMP: prevent use of the console when using idmap_pgd
ARM: 7412/1: audit: use only AUDIT_ARCH_ARM regardless of endianness
ARM: 7411/1: audit: fix treatment of saved ip register during syscall tracing
ARM: 7410/1: Add extra clobber registers for assembly in kernel_execve
If RSS is disabled on the PF (efx->n_rx_channels == 1) we try to set
up the indirection table so that VFs can use it, setting
efx->rss_spread = efx_vf_size(efx). But if SR-IOV was disabled at
compile time, this evaluates to 0 and we end up dividing by zero when
initialising the table.
I considered changing the fallback definition of efx_vf_size() to
return 1, but its value is really meaningless if we are not going to
enable VFs. Therefore add a condition of efx_sriov_wanted(efx) in
efx_probe_interrupts().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In case of short marker, the number of received packets was not
incremented doing a zero divide when computing the filling rate.
Reported-by: Hans Petter Selasky <hans.petter.selasky@bitfrost.no>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size. PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future. Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.
With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.
As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.
v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
x86_32 PAGE_SIZE as suggested by hpa.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yanmin Zhang <yanmin.zhang@intel.com>
Reported-by: ShuoX Liu <shuox.liu@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4F97BA98.6010001@intel.com>
Cc: stable@vger.kernel.org
The H_REGISTER_VPA hcall implementation in HV Power KVM needs to pin some
guest memory pages into host memory so that they can be safely accessed
from usermode. It does this used get_user_pages_fast(). When the VPA is
unregistered, or the VCPUs are cleaned up, these pages are released using
put_page().
However, the get_user_pages() is invoked on the specific memory are of the
VPA which could lie within hugepages. In case the pinned page is huge,
we explicitly find the head page of the compound page before calling
put_page() on it.
At least with the latest kernel, this is not correct. put_page() already
handles finding the correct head page of a compound, and also deals with
various counts on the individual tail page which are important for
transparent huge pages. We don't support transparent hugepages on Power,
but even so, bypassing this count maintenance can lead (when the VM ends)
to a hugepage being released back to the pool with a non-zero mapcount on
one of the tail pages. This can then lead to a bad_page() when the page
is released from the hugepage pool.
This removes the explicit compound_head() call to correct this bug.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 785f857d1c.
The commit causes a problem with the wrong D3 state after suspend
because the call of hda_set_power_state() involves with the power-up
sequence, which changes the power_count, and this confuses the resume
sequence that checks the power_count as well.
Originally, this go-to-D3 sequence should be a simple task without the
power-up sequence. But, it'd need some proper sanity checks in the
case of power-saved state, so it's not too easy to write now in the
3.4-rc cycle.
In short, the safest option now is to revert this affecting commit.
Of course, we need to clean up and robustify the power-saving code
better for 3.5 kernel.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Include the header to pickup the definitions of the exported symbols.
Quiets the following sparse warnings:
warning: symbol 'vb2_dma_contig_memops' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_init_ctx' was not declared. Should it be static?
warning: symbol 'vb2_dma_contig_cleanup_ctx' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit 3b4c34aac7
"s5p-fimc: Add support for VIDIOC_PREPARE_BUF/CREATE_BUFS ioctls"
added a handler for VIDIOC_CREATE_BUFS ioctl, but the queue_setup
callback wasn't updated to properly interpret the pixel format.
In this situation memory corruption may happen with VIDIOC_CREATE_BUFS
ioctl. Update the queue_setup op to fix this.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The call for alc_auto_parse_customize_define() must be done after the
fixup pre-probe initialization. Otherwise SKU_IGNORE fixup won't work
properly (e.g. HP RP5800 with ALC662 codec).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.
Cc: stable@vger.kernel.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
snd_hdsp uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit applications can use it on 64bit kernels.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com>
Reviewed-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable Coldfire QSPI support when SPI_COLDFIRE_QSPI is built as a module.
This version of the patch combines changes to the config files and device.c
and uses IF_ENABLED (thanks to Sam Ravnborg for the suggestion).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When the kernel validates set TCP/UDP port actions, it looks at
the ports in the existing flow to make sure that the L4 header exists.
However, these actions always use the IPv4 version of the struct.
Following patch fixes this by checking for flow ip protocol first.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Neither compare_ether_addr() nor compare_ether_addr_64bits()
(as it can fall back to the former) have comparison semantics
like memcmp() where the sign of the return value indicates sort
order. We had a bug in the wireless code due to a blind memcmp
replacement because of this.
A cursory look suggests that the wireless bug was the only one
due to this semantic difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locking policy is such that the erase_complete_block spinlock is
nested within the alloc_sem mutex. This fixes a case in which the
acquisition order was erroneously reversed. This issue was caught by
the following lockdep splat:
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.5 #1
-------------------------------------------------------
jffs2_gcd_mtd6/299 is trying to acquire lock:
(&c->alloc_sem){+.+.+.}, at: [<c01f7714>] jffs2_garbage_collect_pass+0x314/0x890
but task is already holding lock:
(&(&c->erase_completion_lock)->rlock){+.+...}, at: [<c01f7708>] jffs2_garbage_collect_pass+0x308/0x890
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(&c->erase_completion_lock)->rlock){+.+...}:
[<c008bec4>] validate_chain+0xe6c/0x10bc
[<c008c660>] __lock_acquire+0x54c/0xba4
[<c008d240>] lock_acquire+0xa4/0x114
[<c046780c>] _raw_spin_lock+0x3c/0x4c
[<c01f744c>] jffs2_garbage_collect_pass+0x4c/0x890
[<c01f937c>] jffs2_garbage_collect_thread+0x1b4/0x1cc
[<c0071a68>] kthread+0x98/0xa0
[<c000f264>] kernel_thread_exit+0x0/0x8
-> #0 (&c->alloc_sem){+.+.+.}:
[<c008ad2c>] print_circular_bug+0x70/0x2c4
[<c008c08c>] validate_chain+0x1034/0x10bc
[<c008c660>] __lock_acquire+0x54c/0xba4
[<c008d240>] lock_acquire+0xa4/0x114
[<c0466628>] mutex_lock_nested+0x74/0x33c
[<c01f7714>] jffs2_garbage_collect_pass+0x314/0x890
[<c01f937c>] jffs2_garbage_collect_thread+0x1b4/0x1cc
[<c0071a68>] kthread+0x98/0xa0
[<c000f264>] kernel_thread_exit+0x0/0x8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&c->erase_completion_lock)->rlock);
lock(&c->alloc_sem);
lock(&(&c->erase_completion_lock)->rlock);
lock(&c->alloc_sem);
*** DEADLOCK ***
1 lock held by jffs2_gcd_mtd6/299:
#0: (&(&c->erase_completion_lock)->rlock){+.+...}, at: [<c01f7708>] jffs2_garbage_collect_pass+0x308/0x890
stack backtrace:
[<c00155dc>] (unwind_backtrace+0x0/0x100) from [<c0463dc0>] (dump_stack+0x20/0x24)
[<c0463dc0>] (dump_stack+0x20/0x24) from [<c008ae84>] (print_circular_bug+0x1c8/0x2c4)
[<c008ae84>] (print_circular_bug+0x1c8/0x2c4) from [<c008c08c>] (validate_chain+0x1034/0x10bc)
[<c008c08c>] (validate_chain+0x1034/0x10bc) from [<c008c660>] (__lock_acquire+0x54c/0xba4)
[<c008c660>] (__lock_acquire+0x54c/0xba4) from [<c008d240>] (lock_acquire+0xa4/0x114)
[<c008d240>] (lock_acquire+0xa4/0x114) from [<c0466628>] (mutex_lock_nested+0x74/0x33c)
[<c0466628>] (mutex_lock_nested+0x74/0x33c) from [<c01f7714>] (jffs2_garbage_collect_pass+0x314/0x890)
[<c01f7714>] (jffs2_garbage_collect_pass+0x314/0x890) from [<c01f937c>] (jffs2_garbage_collect_thread+0x1b4/0x1cc)
[<c01f937c>] (jffs2_garbage_collect_thread+0x1b4/0x1cc) from [<c0071a68>] (kthread+0x98/0xa0)
[<c0071a68>] (kthread+0x98/0xa0) from [<c000f264>] (kernel_thread_exit+0x0/0x8)
This was introduce in '81cfc9f jffs2: Fix serious write stall due to erase'.
Cc: stable@kernel.org [2.6.37+]
Signed-off-by: Josh Cartwright <joshc@linux.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I'm seeing an oops in mtd_dataflash.c with Linux 3.3. What appears to
be happening is that otp_select_filemode calls mtd_read_fact_prot_reg
with -1 for offset and length and a NULL buffer to test if OTP
operations are supported. This finds its way down to otp_read in
mtd_dataflash.c and causes an oops when memcpying the returned data
into the NULL buf.
None of the checks in otp_read catches the negative length and offset.
Changing the length of the dummy read to 0 prevents the oops.
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The accessing PCI configuration space with the PCI BIOS32 service does
not work in PV guests.
On systems without MMCONFIG or where the BIOS hasn't marked the
MMCONFIG region as reserved in the e820 map, the BIOS service is
probed (even though direct access is preferred) and this hangs.
CC: stable@kernel.org
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[v1: Fixed compile error when CONFIG_PCI is not set]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If I try to do "cat /sys/kernel/debug/kernel_page_tables"
I end up with:
BUG: unable to handle kernel paging request at ffffc7fffffff000
IP: [<ffffffff8106aa51>] ptdump_show+0x221/0x480
PGD 0
Oops: 0000 [#1] SMP
CPU 0
.. snip..
RAX: 0000000000000000 RBX: ffffc00000000fff RCX: 0000000000000000
RDX: 0000800000000000 RSI: 0000000000000000 RDI: ffffc7fffffff000
which is due to the fact we are trying to access a PFN that is not
accessible to us. The reason (at least in this case) was that
PGD[256] is set to __HYPERVISOR_VIRT_START which was setup (by the
hypervisor) to point to a read-only linear map of the MFN->PFN array.
During our parsing we would get the MFN (a valid one), try to look
it up in the MFN->PFN tree and find it invalid and return ~0 as PFN.
Then pte_mfn_to_pfn would happilly feed that in, attach the flags
and return it back to the caller. 'ptdump_show' bitshifts it and
gets and invalid value that it tries to dereference.
Instead of doing all of that, we detect the ~0 case and just
return !_PAGE_PRESENT.
This bug has been in existence .. at least until 2.6.37 (yikes!)
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
On x86_64 on AMD machines where the first APIC_ID is not zero, we get:
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] enabled)
BIOS bug: APIC version is 0 for CPU 1/0x10, fixing up to 0x10
BIOS bug: APIC version mismatch, boot CPU: 0, CPU 1: version 10
which means that when the ACPI processor driver loads and
tries to parse the _Pxx states it fails to do as, as it
ends up calling acpi_get_cpuid which does this:
for_each_possible_cpu(i) {
if (cpu_physical_id(i) == apic_id)
return i;
}
And the bootup CPU, has not been found so it fails and returns -1
for the first CPU - which then subsequently in the loop that
"acpi_processor_get_info" does results in returning an error, which
means that "acpi_processor_add" failing and per_cpu(processor)
is never set (and is NULL).
That means that when xen-acpi-processor tries to load (much much
later on) and parse the P-states it gets -ENODEV from
acpi_processor_register_performance() (which tries to read
the per_cpu(processor)) and fails to parse the data.
Reported-by-and-Tested-by: Stefan Bader <stefan.bader@canonical.com>
Suggested-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
[v2: Bit-shift APIC ID by 24 bits]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
It turns out that (quite surprisingly) devres_destroy() only undoes the
devres mapping, it doesn't destroy the underlying resource, meaning that
anything using devm_regulator_put() would leak. While we wait for the new
devres_release() which does what we want to get merged open code it in
devm_regulator_put().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The operations in the subsequent error-handling code appear to be also
useful here.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[v1: Collapse some of the error handling functions]
[v2: Fix compile warning]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Previous issues with i2c-algo-bit have now been resolved.
This is a revert of f553b79c03 mostly,
due to fixes in the i2c core repairing the original issue, this code
isn't required and was causing regressions.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel wrote:
2 little patches:
- One regression fix to disable sdvo hotplug on broken hw.
- One patch to upconvert the snb hang workaround from patch v1 to patch
v2.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Do no set Stencil Cache eviction LRA w/a on gen7+
drm/i915: disable sdvo hotplug on i945g/gm
Chris Wilson dug out a hw erratum saying that there's noise on the
interrupt line on i945G chips. We also have a bug report from a i945GM
chip with an sdvo hotplug interrupt storm (and no apparent cause).
Play it safe and disable sdvo hotplug on all i945 variants.
Note that this is a regression that has been introduced in 3.1,
when we've enabled sdvo hotplug support with
commit cc68c81aed
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date: Wed Sep 21 17:13:30 2011 +0100
drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI
Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442
Reported-and-tested-by: Dominik Köppl <dominik@devwork.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit ce7e5d2d19 ("x86: fix broken TASK_SIZE for ia32_aout") breaks
kernel builds when "CONFIG_IA32_AOUT=m" with
ERROR: "set_personality_ia32" [arch/x86/ia32/ia32_aout.ko] undefined!
make[1]: *** [__modpost] Error 1
The entry point needs to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Al Viro <viro@zeniv.linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes form Peter Anvin
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
x86, relocs: Remove an unused variable
asm-generic: Use __BITS_PER_LONG in statfs.h
x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it
Pull btrfs fixes from Chris Mason:
"The big ones here are a memory leak we introduced in rc1, and a
scheduling while atomic if the transid on disk doesn't match the
transid we expected. This happens for corrupt blocks, or out of date
disks.
It also fixes up the ioctl definition for our ioctl to resolve logical
inode numbers. The __u32 was a merging error and doesn't match what
we ship in the progs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: avoid sleeping in verify_parent_transid while atomic
Btrfs: fix crash in scrub repair code when device is missing
btrfs: Fix mismatching struct members in ioctl.h
Btrfs: fix page leak when allocing extent buffers
Btrfs: Add properly locking around add_root_to_dirty_list
Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there. Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some RNDIS devices include a bogus CDC Union descriptor pointing
to non-existing interfaces. The RNDIS code is already prepared
to handle devices without a CDC Union descriptor by hardwiring
the driver to use interfaces 0 and 1, which is correct for the
devices with the bogus descriptor as well. So we can reuse the
existing workaround.
Cc: Markus Kolb <linux-201011@tower-net.de>
Cc: Iker Salmón San Millán <shaola@esdebian.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: 655387@bugs.debian.org
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a bug fix for an "interface fails to load" issue.
The issue occurs when bnx2x driver loads after UNDI driver was previously
loaded over the chip. In such a scenario the UNDI driver is loaded and operates
in the pre-boot kernel, within its own specific host memory address range.
When the pre-boot stage is complete, the real kernel is loaded, in a new and
distinct host memory address range. The transition from pre-boot stage to boot
is asynchronous from UNDI point of view.
A race condition occurs when UNDI driver triggers a DMAE transaction to valid
host addresses in the pre-boot stage, when control is diverted to the real
kernel. This results in access to illegal addresses by our HW as the addresses
which were valid in the preboot stage are no longer considered valid.
Specifically, the 'was_error' bit in the pci glue of our device is set. This
causes all following pci transactions from chip to host to timeout (in
accordance to the pci spec).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turned to be totally unneeded. The reason the code was introduced is
so that KVM can prefault swapped in page, but prefault can fail even
if mm is pinned since page table can change anyway. KVM handles this
situation correctly though and does not inject spurious page faults.
Fixes:
"INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected" warning while
running LTP inside a KVM guest using the recent -next kernel.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If vcpu executes hlt instruction while async PF is waiting to be delivered
vcpu can block and deliver async PF only after another even wakes it
up. This happens because kvm_check_async_pf_completion() will remove
completion event from vcpu->async_pf.done before entering kvm_vcpu_block()
and this will make kvm_arch_vcpu_runnable() return false. The solution
is to make vcpu runnable when processing completion.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.
But, a few callers are using it with spinlocks held. Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case. This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This assertion seems to imply that chip->dsp_code_to_load is a pointer.
It's actually an integer handle on the actual firmware, and 0 has no
special meaning.
The assertion prevents initialisation of a Darla20 card, but would also
affect other models. It seems it was introduced in commit dd7b254d.
ALSA sound/pci/echoaudio/echoaudio.c:2061 Echoaudio driver starting...
ALSA sound/pci/echoaudio/echoaudio.c:1969 chip=ebe4e000
ALSA sound/pci/echoaudio/echoaudio.c:2007 pci=ed568000 irq=19 subdev=0010 Init hardware...
ALSA sound/pci/echoaudio/darla20_dsp.c:36 init_hw() - Darla20
------------[ cut here ]------------
WARNING: at sound/pci/echoaudio/echoaudio_dsp.c:478 init_hw+0x1d1/0x86c [snd_darla20]()
Hardware name: Dell DM051
BUG? (!chip->dsp_code_to_load || !chip->comm_page)
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 4e8ee7de22 (ARM: SMP: use
idmap_pgd for mapping MMU enable during secondary booting)
switched secondary boot to use idmap_pgd, which is initialized
during early_initcall, instead of a page table initialized during
__cpu_up. This causes idmap_pgd to contain the static mappings
but be missing all dynamic mappings.
If a console is registered that creates a dynamic mapping, the
printk in secondary_start_kernel will trigger a data abort on
the missing mapping before the exception handlers have been
initialized, leading to a hang. Initial boot is not affected
because no consoles have been registered, and resume is usually
not affected because the offending console is suspended.
Onlining a cpu with hotplug triggers the problem.
A workaround is to the printk in secondary_start_kernel until
after the page tables have been switched back to init_mm.
Cc: <stable@vger.kernel.org>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull alpha fixes from Matt Turner:
"My alpha tree is back up (after taking quite some time to get my GPG
key signed). It contains just some simple fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: silence 'const' warning in sys_marvel.c
alpha: include module.h to fix modpost on Tsunami
alpha: properly define get/set_rtc_time on Marvel/SMP
alpha: VGA_HOSE depends on VGA_CONSOLE
The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.
This did not matter until commit 5dd5bc40f3 ("TTY: pdc_cons, use
tty_port"). There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.
So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.
Well, the driver should not touch tty->count at all. It should use
tty_port->count and count open count there itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-tested-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Pull an ACPI patch from Len Brown:
"It fixes a D3 issue new in 3.4-rc1."
By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: Fix D3hot v D3cold confusion
Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root. This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:
[ 101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
[ 101.534499] VFS: Mounted root (9p filesystem) on device 0:18.
Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.
This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.
This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major. This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The machine endianness has no direct correspondence to the syscall ABI,
so use only AUDIT_ARCH_ARM when identifying the ABI to the audit tools
in userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM audit code incorrectly uses the saved application ip register
value to infer syscall entry or exit. Additionally, the saved value will
be clobbered if the current task is not being traced, which can lead to
libc corruption if ip is live (apparently glibc uses it for the TLS
pointer).
This patch fixes the syscall tracing code so that the why parameter is
used to infer the syscall direction and the saved ip is only updated if
we know that we will be signalling a ptrace trap.
Reported-and-Tested-by: Jon Masters <jcm@jonmasters.org>
Cc: stable@vger.kernel.org
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The inline assembly in kernel_execve() uses r8 and r9. Since this
code sequence does not return, it usually doesn't matter if the
register clobber list is accurate. However, I saw a case where a
particular version of gcc used r8 as an intermediate for the value
eventually passed to r9. Because r8 is used in the inline
assembly, and not mentioned in the clobber list, r9 was set
to an incorrect value.
This resulted in a kernel panic on execution of the first user-space
program in the system. r9 is used in ret_to_user as the thread_info
pointer, and if it's wrong, bad things happen.
Cc: <stable@vger.kernel.org>
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull timer fix from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtc: Fix possible null pointer dereference in rtc-mpc5121.c
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
fs/cifs: fix parsing of dfs referrals
cifs: make sure we ignore the credentials= and cred= options
[CIFS] Update cifs version to 1.78
cifs - check S_AUTOMOUNT in revalidate
cifs: add missing initialization of server->req_lock
cifs: don't cap ra_pages at the same level as default_backing_dev_info
CIFS: Fix indentation in cifs_show_options
Remove myself as cpufreq maintainer.
x86 driver changes can go through the regular x86/ACPI trees.
ARM driver changes through the ARM trees.
cpufreq core changes are rare these days, and can just go to lkml/direct.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The normal read_seqcount_begin() function will wait for any current
writers to exit their critical region by looping until the sequence
count is even.
That "wait for sequence count to stabilize" is the right thing to do if
the read-locker will just retry the whole operation on contention: no
point in doing a potentially expensive reader sequence if we know at the
beginning that we'll just end up re-doing it all.
HOWEVER. Some users don't actually retry the operation, but instead
will abort and do the operation with proper locking. So the sequence
count case may be the optimistic quick case, but in the presense of
writers you may want to do full locking in order to guarantee forward
progress. The prime example of this would be the RCU name lookup.
And in that case, you may well be better off without the "retry early",
and are in a rush to instead get to the failure handling. Thus this
"raw" interface that just returns the sequence number without testing it
- it just forces the low bit to zero so that read_seqcount_retry() will
always fail such a "active concurrent writer" scenario.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it. As a
result, it might end up returning an odd value (which means that a write
is in progress).
If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.
In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.
So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload. But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug. Let's just make sure.
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that there was an error with the active_low = 1 for the
LED, since it should be set to 0 (meaning that active is high,
since 0 is false, hence the confusion.
The wiki article about it confuses it, since it contradicts itself,
regarding what turns on the LED.
I have tested 3.4-rc2 on my net5501 with this patch, and it makes the LED
behave correctly, where "none" turns it off, and "default-on" turns it on,
when echoed onto the trigger "file" in /sys/class/leds.
Signed-off-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Link: http://lkml.kernel.org/r/20120504210146.62186A018B@akpm.mtv.corp.google.com
Cc: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit 46f8c3c7e9.
The commit above swapped the DSI1_PPID and DSI2_PPID register fields in
CONTROL_DSIPHY to be in sync with the newer public OMAP TRMs(after version V).
With this commit, contention errors were reported on DSI lanes some OMAP4 SDPs.
After probing the DSI lanes on OMAP4 SDP, it was seen that setting bits in the
DSI2_PPID field was pulling up voltage on DSI1 lanes, and DSI1_PPID field was
pulling up voltage on DSI2 lanes.
This proves that the current version of OMAP4 TRM is incorrect, swap the
position of register fields according to the older TRM versions as they were
correct.
Cc: stable@vger.kernel.org # v3.2+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix that when scrub tries to repair an I/O or checksum error and one of
the devices containing the mirror is missing, it crashes in bio_add_page
because the bdev is a NULL pointer for missing devices.
Reported-by: Marco L. Crociani <marco.crociani@gmail.com>
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Fix the size members of btrfs_ioctl_ino_path_args and
btrfs_ioctl_logical_ino_args. The user space btrfs-progs utilities used
__u64 and the kernel headers used __u32 before.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If we happen to alloc a extent buffer and then alloc a page and notice that
page is already attached to an extent buffer, we will only unlock it and
free our existing eb. Any pages currently attached to that eb will be
properly freed, but we don't do the page_cache_release() on the page where
we noticed the other extent buffer which can cause us to leak pages and I
hope cause the weird issues we've been seeing in this area. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
add_root_to_dirty_list happens once at the very beginning of the
transaction, but it is still racey.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Commit 384ebe1c28, "gpio/omap: Add DT
support to GPIO driver", introduced dynamic IRQ numbering of OMAP GPIO
interrupts, breaking all IH_GPIO_BASE based IRQ number calculations.
This issue was corrected in the OMAP GPIO driver and the related header
file with commit 25db711df3, "gpio/omap:
Fix IRQ handling for SPARSE_IRQ".
However, the Amstrad Delta FIQ handler, which replaces the gpio-omap
driver in serving GPIO interrupts on this board, still uses that
outdated method. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull drm fixes from Dave Airlie:
"Some minor fixes from Intel and a radeon fix.
I have the nouveau fix for the i2c regression queued for next week,
its mostly a revert and seems to work on the system it was originally
introduced for thanks to some i2c core changes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: clarify and extend wb setup on APUs and NI+ asics
drm/i915: enable dip before writing data on gen4
fixing dmi match for hp t5745 and hp st5747 thin client
drm/i915: Only enable IPS polling for gen5
drm/i915: Do not read non-existent DPLL registers on PCH hardware
Pull one small fix for md/bitmaps from NeilBrown:
"This fixes a regression that was introduced in the merge window."
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/bitmap: fix calculation of 'chunks' - missing shift.
Jana Saout confirmed that this fixes the page faults he saw.
His problem was triggered by ocfs2 and autofs symlink lookups, where the
symlink allocation was at the end of a page. But the deeper reason
seems to be the use of Xen-PV, which is what then causes him to have all
these unmapped pages, which is what then makes it a problem when the
unaligned word-at-a-time code fetches data past the end of a page.
* fix-unmapped-word-at-a-time:
vfs: make word-at-a-time accesses handle a non-existing page
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use family rather than DCE check for clarity, also always use
wb on APUs, there will never be AGP variants.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 61a0d80c "md/bitmap: discard CHUNK_BLOCK_SHIFT macro"
replaced CHUNK_BLOCK_RATIO() by the same text that was
replacing CHUNK_BLOCK_SHIFT() - which is clearly wrong.
The result is that 'chunks' is often too small by 1,
which can sometimes result in a crash (not sure how).
So use the correct replacement, and get rid of CHUNK_BLOCK_RATIO
which is no longe used.
Reported-by: Karl Newman <siliconfiend@gmail.com>
Tested-by: Karl Newman <siliconfiend@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The problem was that the first referral was parsed more than once
and so the caller tried the same referrals multiple times.
The problem was introduced partly by commit
066ce68994,
where 'ref += le16_to_cpu(ref->Size);' got lost,
but that was also wrong...
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Tested-by: Björn Jacke <bj@sernet.de>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch fixes a possible lock-up bug where rtnl_lock might not
get released.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Pull second set of MFD fixes from Samuel Ortiz:
"This time we only have a one liner fixing an omap-usb build error."
* tag 'mfd-for-linus-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix build breakage in omap-usb-host.c
Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull libata fixes from Jeff Garzik:
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
libata: init ata_print_id to 0
ahci: Detect Marvell 88SE9172 SATA controller
libata: skip old error history when counting probe trials
Pull i2c embedded fixes from Wolfram Sang:
"Here are some typical i2c driver bugfixes for 3.4. Missed clock
handling, improper timeout fixes, hardware wrokarounds... All
patches have been in linux-next for a few days, too."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: disable QUEUE when sending is done
i2c: mxs: handle spurious interrupt
i2c-eg20t: Modify MODULE_AUTHOR's email address
i2c-eg20t: change timeout value 50msec to 1000msec
i2c: tegra: Add delay before resetting the controller after NACK
i2c: pnx: Disable clk in suspend
Pull drm fixes from Dave Airlie:
"Just some regression fixes from Ben along with a variable that gcc
failed to spot is uninitialised."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: initialise has_optimus variable.
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
Pull networking fixes from David Miller:
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
Pull hwmon fixes from Guenter Roeck:
"Fix OOPS seen in coretemp driver if the CPU core ID is too large"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Increase CPU core limit
hwmon: (coretemp) fix oops on cpu unplug
It turns out that there are more cases than CONFIG_DEBUG_PAGEALLOC that
can have holes in the kernel address space: it seems to happen easily
with Xen, and it looks like the AMD gart64 code will also punch holes
dynamically.
Actually hitting that case is still very unlikely, so just do the
access, and take an exception and fix it up for the very unlikely case
of it being a page-crosser with no next page.
And hey, this abstraction might even help other architectures that have
other issues with unaligned word accesses than the possible missing next
page. IOW, this could do the byte order magic too.
Peter Anvin fixed a thinko in the shifting for the exception case.
Reported-and-tested-by: Jana Saout <jana@saout.de>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When revalidating a dentry, if the inode wasn't known to be a dfs
entry when the dentry was instantiated, such as when created via
->readdir(), the DCACHE_NEED_AUTOMOUNT flag needs to be set on the
dentry in ->d_revalidate().
The false return from cifs_d_revalidate(), due to the inode now
being marked with the S_AUTOMOUNT flag, might not invalidate the
dentry if there is a concurrent unlazy path walk. This is because
the dentry reference count will be at least 2 in this case causing
d_invalidate() to return EBUSY. So the asumption that the dentry
will be discarded then correctly instantiated via ->lookup() might
not hold.
Signed-off-by: Ian Kent <raven@themaw.net>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Cc: Steve French <smfrench@gmail.com>
Cc: linux-cifs@vger.kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
SPEAr13xx series of SoCs contain Synopsys AHCI SATA Controller which shares
ahci_platform driver with other controller versions.
This patch updates DT compatible list for ahci_platform. It also updates and
renames binding documentation to more generic name.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
#ifdef, #endif is not required in definition/usage of arasan_cf_pm_ops. So, move
this definition and its usage outside of them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:
-ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
-ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
-ata3: DUMMY
+ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
+ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
ata4: DUMMY
ata5: DUMMY
-ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
+ata6: DUMMY
+ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
The change of numbering comes from commit 85d6725b7c ("libata:
make ata_print_id atomic") that changed lines like
ap->print_id = ata_print_id++;
to
ap->print_id = atomic_inc_return(&ata_print_id);
As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The Marvell 88SE9172 SATA controller (PCI ID 1b4b 917a) already worked
once it was detected, but was missing an ahci_pci_tbl entry.
Boot tested on a Gigabyte Z68X-UD3H-B3 motherboard.
Signed-off-by: Matt Johnson <johnso87@illinois.edu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d902747("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.
But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.
Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().
Cc: stable <stable@vger.kernel.org> # 2.6.37+
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gss_mech_list_pseudoflavors() parses a list of registered mechanisms.
On that list contains a list of pseudo flavors which was not being
parsed correctly, causing only the first pseudo flavor to be found.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: enable dip before writing data on gen4
fixing dmi match for hp t5745 and hp st5747 thin client
drm/i915: Only enable IPS polling for gen5
drm/i915: Do not read non-existent DPLL registers on PCH hardware
By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.
This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.
As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.
Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While testing with the intel_infoframes tool on gen4, I see that when
video DIP is disabled, what we write to the DATA memory is not exactly
what we read back later.
This regression has been introduce in
commit 64a8fc0145
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Sep 22 11:16:00 2011 +0530
drm/i915: fix ILK+ infoframe support
That commit was setting VIDEO_DIP_CTL to 0 when initializing, which
caused the problem.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43947
Cc: stable@kernel.org
Tested-by: Yang Guang <guang.a.yang@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pimped commit message by using the usual commit citation
layout.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After this commit:
commit aacc1bea19
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date: Wed Mar 28 07:49:09 2012 +0000
ixgbe: driver fix for link flap
The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.
We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was possible for shutdown to pull the rug out from other driver entry
points. Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_ip_sendmsg could return without releasing socket lock, making it all the
way to userspace, and generating the following warning:
[ 130.891594] ================================================
[ 130.894569] [ BUG: lock held when returning to user space! ]
[ 130.897257] 3.4.0-rc5-next-20120501-sasha #104 Tainted: G W
[ 130.900336] ------------------------------------------------
[ 130.902996] trinity/8384 is leaving the kernel with locks still held!
[ 130.906106] 1 lock held by trinity/8384:
[ 130.907924] #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff82b9503f>] l2tp_ip_sendmsg+0x2f/0x550
Introduced by commit 2f16270 ("l2tp: Fix locking in l2tp_ip.c").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just noticed after some recent updates, that the init path for the drop
monitor protocol has a minor error. drop monitor maintains a per cpu structure,
that gets initalized from a single cpu. Normally this is fine, as the protocol
isn't in use yet, but I recently made a change that causes a failed skb
allocation to reschedule itself . Given the current code, the implication is
that this workqueue reschedule will take place on the wrong cpu. If drop
monitor is used early during the boot process, its possible that two cpus will
access a single per-cpu structure in parallel, possibly leading to data
corruption.
This patch fixes the situation, by storing the cpu number that a given instance
of this per-cpu data should be accessed from. In the case of a need for a
reschedule, the cpu stored in the struct is assigned the rescheule, rather than
the currently executing cpu
Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
warning: passing argument 1 of 'pci_find_capability' discards 'const' qualifier from pointer target type
Signed-off-by: Matt Turner <mattst88@gmail.com>
The marvel_get_rtc_time and marvel_set_rtc_time are static, but they're
available through Marvel's machine vector.
Reported-by: Raúl Porcel <armin76@gentoo.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
arch/alpha/kernel/console.c:locate_and_init_vga uses vga_con, causing
build failures if VGA_CONSOLE was not set and MARVEL, TITAN, DP264, or
GENERIC alpha system types were set.
Reported-by: Raúl Porcel <armin76@gentoo.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
This reverts commit a844adfd7b.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.
spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.
So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for perf/urgent:
- Add fallback in 'perf stat' for kernels that don't support
perf_event_attr.exclude_guest, from Stephane Eranian.
- Fix build id cache add routine to take the size of the buffer and not of a
pointer, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull NFS client bugfixes from Trond Myklebust:
- Fixes for the NFSv4 security negotiation
- Use the correct hostname when mounting from a private namespace
- NFS net namespace bugfixes for the pipefs filesystem
- NFSv4 GETACL bugfixes
- IPv6 bugfix for NFSv4 referrals
* tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Use the correct hostname in the client identifier string
SUNRPC: RPC client must use the current utsname hostname string
NFS: get module in idmap PipeFS notifier callback
NFS: Remove unused function nfs_lookup_with_sec()
NFS: Honor the authflavor set in the clone mount data
NFS: Fix following referral mount points with different security
NFS: Do secinfo as part of lookup
NFS: Handle exceptions coming out of nfs4_proc_fs_locations()
NFS: Fix SECINFO_NO_NAME
SUNRPC: traverse clients tree on PipeFS event
SUNRPC: set per-net PipeFS superblock before notification
SUNRPC: skip clients with program without PipeFS entries
SUNRPC: skip dead but not buried clients on PipeFS events
Avoid beyond bounds copy while caching ACL
Avoid reading past buffer when calling GETACL
fix page number calculation bug for block layout decode buffer
NFSv4.1 fix page number calculation bug for filelayout decode buffers
pnfs-obj: Remove unused variable from objlayout_get_deviceinfo()
nfs4: fix referrals on mounts that use IPv6 addrs
On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.
Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While testing, I've found that even when we are able to negotiate a
much larger rsize with the server, on-the-wire reads often end up being
capped at 128k because of ra_pages being capped at that level.
Lifting this restriction gave almost a twofold increase in sequential
read performance on my craptactular KVM test rig with a 1M rsize.
I think this is safe since the actual ra_pages that the VM requests
is run through max_sane_readahead() prior to submitting the I/O. Under
memory pressure we should end up with large readahead requests being
suppressed anyway.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Trivial patch which fixes a misplaced tab in cifs_show_options().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull two bug fixes in ktest from Steven Rostedt.
* tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix reboot on success stopping all reboots
ktest.pl: Fix combined usage of BISECT_REVERSE and BISECT_SKIP
Pull MIPS fixes from Ralf Baechle:
"misc fixes some of which are also applicable to 3.3 and removal of an
unused function. This has been sitting in -next for ages with no
complaints. Also there are no known regressions due to these patches"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Remove get_current_pgd().
MIPS: ath79: fix AR933X WMAC reset code
MIPS: JZ4740: Fix the JZ4740_IRQ_DMA macro
MIPS: Use set_current_blocked() and block_sigmask()
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, perf stat sets exclude_guest = 1. But when you run perf on a
kernel which does not support host/guest filtering, then you get an
error saying the event in unsupported. This comes from the fact that
when the perf_event_attr struct passed by the user is larger than the
one known to the kernel there is safety check which ensures that all
unknown bits are zero. But here, exclude_guest is 1 (part of the unknown
bits) and thus the perf_event_open() syscall return EINVAL.
To my surprise, running perf record on the same kernel did not exhibit
the problem. The reason is that perf record handles the problem by
catching the error and retrying with guest/host excludes set to zero.
For some reason, this was not done with perf stat. This patch fixes this
problem.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/20120427124538.GA7230@quad
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
The change to let individual tests decide to reboot the machine on
success of the entire test also prevented errors from rebooting
when an error was detected.
The "no_reboot" variable was only cleared if the test had
reboot_on_success set. But the no_reboot variable also prevents the test
rebooting when an error was detected even when REBOOT_ON_ERROR was set.
Add a new "reboot_success" variable that is used to determine if the
test should reboot on success and not touch the no_reboot variable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When BISECT_REVERSE and BISECT_SKIP are used together with boot or test
testing, build failures are treated as boot or test failures and
'git bisect bad' is executed instead of 'git bisect skip'. This is because
the $ret value of -1 is treated as a build failure, but the $reverse_bisect
logic does not properly handle this.
Simple fix, only invert it if it is positive.
Link: http://lkml.kernel.org/r/1335235380-8509-1-git-send-email-Russ.Dill@ti.com
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As s3c2412-i2s is using the s3c_i2sv2 it should call the more specialised
s3c_i2sv2_register_dai instead of simply calling snd_soc_register_dai.
Without this call the snd_soc_dai_ops structure isn't initialised correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
Pull SCSI fixes from James Bottomley:
"This is a set of SAS and SATA fixes; there are one or two longstanding
bug fixes, but most of this is regression fixes."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] libfc: update mfs boundry checking
[SCSI] Revert "[SCSI] libsas: fix sas port naming"
[SCSI] libsas: fix false positive 'device attached' conditions
[SCSI] libsas, libata: fix start of life for a sas ata_port
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
[SCSI] libsas: unify domain_device sas_rphy lifetimes
[SCSI] libsas: fix sas_get_port_device regression
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
[SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
[SCSI] libata: Pass correct DMA device to scsi host
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix printk format warnings -- both items are size_t,
so use %zu to print them.
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'size_t'
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a handful more fixes for powerpc. The irq stuff are all
regression fixes, and Gavin's patch is a simple compile fix."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
tty/serial/pmac_zilog: Fix "nobody cared" IRQ message
powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
powerpc/irqdomain: Fix broken NR_IRQ references
powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fix from Dmitry Torokhov:
"A simple fix for a recent regression in Synaptics driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix regression with "image sensor" trackpads
We need to use the hostname of the process that created the nfs_client.
That hostname is now stored in the rpc_client->cl_nodename.
Also remove the utsname()->domainname component. There is no reason
to include the NIS/YP domainname in a client identifier string.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that the rpc client is namespace aware, it needs to use the
utsname of the process that created it instead of using the
init_utsname. Both rpc_new_client and rpc_clone_client need to
be fixed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
* commit f9dfbf9 "ASoC: tlv320aic23: convert to soc-cache" leads to
a bug preventing resumeof the codec as regmap expects a 9 bits data
register but 0xFFFF is passed in tlv320aic23_set_bias_level and this
values gets cached preventing any write to the TLV320AIC23_PWR
register as the final value produced by regmap is (register << 9) | value
* this patch solves the problem by only working on the 9 bits the
register contains.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The current checking always succeeded. We have to check the first
character of the string to check that it's empty, thus, skipping
the timeout path.
This fixes the use of the CT target without the timeout option.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Change order of init so netns init is ready
when register ioctl and netlink.
Ver2
Whitespace fixes and __init added.
Reported-by: "Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid crash when registering shedulers after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
We started using the connector table on nv4x a while back, and this VBIOS
has bad connector indices which causes the wrong encoders to get paired
with connectors.
Add a quirk to fix this...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Recently, Ryan Wang tried to compile PPC pSeries platform without
CONFIG_EEH and eventually run into errors. Nishanth Aravamudan
helped to narrow down the root cause. Actually, the pSeries platform
depends on CONFIG_EEH heavily and that won't work properly without
EEH support.
According to Ben's suggestion, the patch make CONFIG_EEH invisible
and keep it as always selected on pSeries platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The switch from using irq_map to irq_alloc_desc*() for managing irq
number allocations introduced new bugs in some of the powerpc
interrupt code. Several functions rely on the value of NR_IRQS to
determine the maximum irq number that could get allocated. However,
with sparse_irq and using irq_alloc_desc*() the maximum possible irq
number is now specified with 'nr_irqs' which may be a number larger
than NR_IRQS. This has caused breakage on powermac when
CONFIG_NR_IRQS is set to 32.
This patch removes most of the direct references to NR_IRQS in the
powerpc code and replaces them with either a nr_irqs reference or by
using the common for_each_irq_desc() macro. The powerpc-specific
for_each_irq() macro is removed at the same time.
Also, the Cell axon_msi driver is refactored to remove the global
build assumption on the size of NR_IRQS and instead add a limit to the
maximum irq number when calling irq_domain_add_nomap().
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpc8xx driver uses a reference to NR_IRQS that is buggy. It uses
NR_IRQs for the array size of the ppc_cached_irq_mask bitmap, but
NR_IRQs could be smaller than the number of hardware irqs that
ppc_cached_irq_mask tracks.
Also, while fixing that problem, it became apparent that the interrupt
controller only supports 32 interrupt numbers, but it is written as if
it supports multiple register banks which is more complicated.
This patch pulls out the buggy reference to NR_IRQs and fixes the size
of the ppc_cached_irq_mask to match the number of HW irqs. It also
drops the now-unnecessary code since ppc_cached_irq_mask is no longer
an array.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4ab ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9de.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit
d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.
When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own. The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).
End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time. You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.
NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops. Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.
The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes). But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org # needed for systemd/autofs interaction fix
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are some tiny drivers/staging/ bugfixes. Some build fixes that
were recently reported, as well as one kfree bug that is hitting a
number of users."
* tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ozwpan: Fix bug where kfree is called twice.
staging: octeon-ethernet: fix build errors by including interrupt.h
staging: zcache: fix Kconfig crypto dependency
staging: tidspbridge: remove usage of OMAP2_L4_IO_ADDRESS
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of small USB fixes for 3.4-rc5.
Nothing major, as before, some USB gadget fixes. There's a crash fix
for a number of ASUS laptops on resume that had been reported by a
number of different people. We think the fix might also pertain to
other machines, as this was a BIOS bug, and they seem to travel to
different models and manufacturers quite easily. Other than that,
some other reported problems fixed as well."
* tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc-core: fix incompatibility with dummy-hcd
usb: gadget: udc-core: fix wrong call order
USB: cdc-wdm: fix race leading leading to memory corruption
USB: EHCI: fix crash during suspend on ASUS computers
usb gadget: uvc: uvc_request_data::length field must be signed
usb: gadget: dummy: do not call pullup() on udc_stop()
usb: musb: davinci.c: add missing unregister
usb: musb: drop __deprecated flag
USB: gadget: storage gadgets send wrong error code for unknown commands
usb: otg: gpio_vbus: Add otg transceiver events and notifiers
This is bug fix.
Notifier callback is called from SUNRPC module. So before dereferencing NFS
module we have to make sure, that it's alive.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull btrfs fixes from Chris Mason:
"This has our collection of bug fixes. I missed the last rc because I
thought our patches were making NFS crash during my xfs test runs.
Turns out it was an NFS client bug fixed by someone else while I tried
to bisect it.
All of these fixes are small, but some are fairly high impact. The
biggest are fixes for our mount -o remount handling, a deadlock due to
GFP_KERNEL allocations in readdir, and a RAID10 error handling bug.
This was tested against both 3.3 and Linus' master as of this morning."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (26 commits)
Btrfs: reduce lock contention during extent insertion
Btrfs: avoid deadlocks from GFP_KERNEL allocations during btrfs_real_readdir
Btrfs: Fix space checking during fs resize
Btrfs: fix block_rsv and space_info lock ordering
Btrfs: Prevent root_list corruption
Btrfs: fix repair code for RAID10
Btrfs: do not start delalloc inodes during sync
Btrfs: fix that check_int_data mount option was ignored
Btrfs: don't count CRC or header errors twice while scrubbing
Btrfs: fix btrfs_ioctl_dev_info() crash on missing device
btrfs: don't return EINTR
Btrfs: double unlock bug in error handling
Btrfs: always store the mirror we read the eb from
fs/btrfs/volumes.c: add missing free_fs_devices
btrfs: fix early abort in 'remount'
Btrfs: fix max chunk size check in chunk allocator
Btrfs: add missing read locks in backref.c
Btrfs: don't call free_extent_buffer twice in iterate_irefs
Btrfs: Make free_ipath() deal gracefully with NULL pointers
Btrfs: avoid possible use-after-free in clear_extent_bit()
...
Pull ARM SoC fixes from Olof Johansson:
"Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors
and warnings mostly, but also some clock/device setup issues on
exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: msm: Fix gic irqdomain support
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
Pull drm fixes from Dave Airlie:
"As soon as I sent the non-urgent stack, two important fixes come in:
- i915: fixes SNB GPU hangs in a number of 3D apps
- radeon: initial fix for VGA on LLano system, 3 or 4 of us have
spent time debugging this, and Jerome finally figured out the magic
bit the BIOS/fglrx set that we didn't. This at least should get
things working, there may be future reliability fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Set the Stencil Cache eviction policy to non-LRA mode.
drm/radeon/kms: need to set up ss on DP bridges as well
This reverts commit a32744d4ab.
While that commit was technically the right thing to do, and made the
x86-64 compat mode work identically to native 32-bit mode (and thus
fixing the problem with a 32-bit systemd install on a 64-bit kernel), it
turns out that the automount binaries had workarounds for this compat
problem.
Now, the workarounds are disgusting: doing an "uname()" to find out the
architecture of the kernel, and then comparing it for the 64-bit cases
and fixing up the size of the read() in automount for those. And they
were confused: it's not actually a generic 64-bit issue at all, it's
very much tied to just x86-64, which has different alignment for an
'u64' in 64-bit mode than in 32-bit mode.
But the end result is that fixing the compat layer actually breaks the
case of a 32-bit automount on a x86-64 kernel.
There are various approaches to fix this (including just doing a
"strcmp()" on current->comm and comparing it to "automount"), but I
think that I will do the one that teaches pipes about a special "packet
mode", which will allow user space to not have to care too deeply about
the padding at the end of the autofs packet.
That change will make the compat workaround unnecessary, so let's revert
it first, and get automount working again in compat mode. The
packetized pipes will then fix autofs for systemd.
Reported-and-requested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Ian Kent <raven@themaw.net>
Cc: stable@kernel.org # for 3.3
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a CPU is hotplugged off, we migrate any IRQs currently affine to it
away and onto another online CPU by calling the irq_set_affinity
function of the relevant interrupt controller chip. This function
returns either IRQ_SET_MASK_OK or IRQ_SET_MASK_OK_NOCOPY, to indicate
whether irq_data.affinity was updated.
If we are forcefully migrating an interrupt (because the affinity mask
no longer identifies any online CPUs) then we should update the IRQ
affinity mask to reflect the new CPU set. Failure to do so can
potentially leave /proc/irq/n/smp_affinity identifying only offline
CPUs, which may confuse userspace IRQ balancing daemons.
This patch updates migrate_one_irq to copy the affinity mask when
the interrupt chip returns IRQ_SET_MASK_OK after forcefully changing the
affinity of an interrupt.
Cc: stable@vger.kernel.org
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When performing a kexec on an SMP system, the secondary cores are stopped
by calling machine_shutdown(), which in turn issues IPIs to offline the
other CPUs. Unfortunately, this isn't enough to reboot the cores into
a new kernel (since they are just executing a cpu_relax loop somewhere
in memory) so we make use of platform_cpu_kill, part of the CPU hotplug
implementation, to place the cores somewhere safe. This function expects
to be called on the killing CPU for each core that it takes out.
This patch moves the platform_cpu_kill callback out of the IPI handler
and into smp_send_stop, therefore ensuring that it executes on the
killing CPU rather than on the victim, matching what the hotplug code
requires.
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TPIDRURW is a user read/write register forming part of the group of
thread registers in more recent versions of the ARM architecture (~v6+).
Currently, the kernel does not touch this register, which allows tasks
to communicate covertly by reading and writing to the register without
context-switching affecting its contents.
This patch clears TPIDRURW when TPIDRURO is updated via the set_tls
macro, which is called directly from __switch_to. Since the current
behaviour makes the register useless to userspace as far as thread
pointers are concerned, simply clearing the register (rather than saving
and restoring it) will not cause any problems to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x111b8): Section mismatch in reference
from the function arm_memory_present() to the function
.init.text:memory_present()
The function arm_memory_present() references
the function __init memory_present().
This is often because arm_memory_present lacks a __init
annotation or the annotation of memory_present is wrong.
WARNING: arch/arm/mm/built-in.o(.text+0x1edc): Section mismatch
in reference from the function alloc_init_pud() to the function
.init.text:alloc_init_section()
The function alloc_init_pud() references
the function __init alloc_init_section().
This is often because alloc_init_pud lacks a __init
annotation or the annotation of alloc_init_section is wrong.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers. Without it, the GPU tries to use the
LRA eviction policy, which isn't supported. This was supposed to be off
by default, but seems to be on for many machines.
This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist. Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535
Cc: stable@vger.kernel.org
Cc: Rob Castle <futuredub@gmail.com>
Cc: Eric Appleman <erappleman@gmail.com>
Cc: aaron667@gmx.net
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections. Specifically, its possible to replace data->skb while its
being written. This patch corrects that by making data->skb an rcu protected
variable. That will prevent it from being overwritten while a tracepoint is
modifying it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet pointed out this warning in the drop_monitor protocol to me:
[ 38.352571] BUG: sleeping function called from invalid context at kernel/mutex.c:85
[ 38.352576] in_atomic(): 1, irqs_disabled(): 0, pid: 4415, name: dropwatch
[ 38.352580] Pid: 4415, comm: dropwatch Not tainted 3.4.0-rc2+ #71
[ 38.352582] Call Trace:
[ 38.352592] [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[ 38.352599] [<ffffffff81063f2a>] __might_sleep+0xca/0xf0
[ 38.352606] [<ffffffff81655b16>] mutex_lock+0x26/0x50
[ 38.352610] [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[ 38.352616] [<ffffffff810b72d9>] tracepoint_probe_register+0x29/0x90
[ 38.352621] [<ffffffff8153a585>] set_all_monitor_traces+0x105/0x170
[ 38.352625] [<ffffffff8153a8ca>] net_dm_cmd_trace+0x2a/0x40
[ 38.352630] [<ffffffff8154a81a>] genl_rcv_msg+0x21a/0x2b0
[ 38.352636] [<ffffffff810f8029>] ? zone_statistics+0x99/0xc0
[ 38.352640] [<ffffffff8154a600>] ? genl_rcv+0x30/0x30
[ 38.352645] [<ffffffff8154a059>] netlink_rcv_skb+0xa9/0xd0
[ 38.352649] [<ffffffff8154a5f0>] genl_rcv+0x20/0x30
[ 38.352653] [<ffffffff81549a7e>] netlink_unicast+0x1ae/0x1f0
[ 38.352658] [<ffffffff81549d76>] netlink_sendmsg+0x2b6/0x310
[ 38.352663] [<ffffffff8150824f>] sock_sendmsg+0x10f/0x130
[ 38.352668] [<ffffffff8150abe0>] ? move_addr_to_kernel+0x60/0xb0
[ 38.352673] [<ffffffff81515f04>] ? verify_iovec+0x64/0xe0
[ 38.352677] [<ffffffff81509c46>] __sys_sendmsg+0x386/0x390
[ 38.352682] [<ffffffff810ffaf9>] ? handle_mm_fault+0x139/0x210
[ 38.352687] [<ffffffff8165b5bc>] ? do_page_fault+0x1ec/0x4f0
[ 38.352693] [<ffffffff8106ba4d>] ? set_next_entity+0x9d/0xb0
[ 38.352699] [<ffffffff81310b49>] ? tty_ldisc_deref+0x9/0x10
[ 38.352703] [<ffffffff8106d363>] ? pick_next_task_fair+0x63/0x140
[ 38.352708] [<ffffffff8150b8d4>] sys_sendmsg+0x44/0x80
[ 38.352713] [<ffffffff8165f8e2>] system_call_fastpath+0x16/0x1b
It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Use correct conversion specifiers in cifs_show_options
CIFS: Show backupuid/gid in /proc/mounts
cifs: fix offset handling in cifs_iovec_write
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Some of these had been in existence since the 2.6.27 days, some since
3.0 - and some due to new features added in v3.4.
The one that is most interesting is David's one - in the low-level
assembler code we had be checking events needlessly. With his patch
now we do it when the appropriate flag is set - with the added benefit
that we can process events faster. Stefano's is fixing a mistake
where the Linux IRQ numbers were ACK-ed instead of the Xen IRQ,
resulting in missing interrupts. The other ones are bootup related
that can show up on various hardware."
- In the low-level assembler code we would jump to check events even if
none were present. This incorrect behavior had been there since
2.6.27 days!
- When using the fast-path for ACK-ing interrupts we were using the
Linux IRQ numbers instead of the Xen ones (and they can differ) and
missing interrupts in process.
- Fix bootup crashes when ACPI hotplug CPUs were present and they would
expand past the set number of CPUs we were allocated.
- Deal with broken BIOSes when uploading C-states to the hypervisor.
- Disable the cpuid check for MWAIT_LEAF if the ACPI PAD driver is
loaded. If the ACPI PAD driver is used it will crash, so lets not
export the functionality so the ACPI PAD driver won't load.
* tag 'stable/for-linus-3.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: correctly check for pending events when restoring irq flags
xen/acpi: Workaround broken BIOSes exporting non-existing C-states.
xen/smp: Fix crash when booting with ACPI hotplug CPUs.
xen: use the pirq number to check the pirq_eoi_map
xen/enlighten: Disable MWAIT_LEAF so that acpi-pad won't be loaded.
Pull misc SPI device driver bug fixes from Grant Likely.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/spi-bfin5xx: Fix flush of last bit after each spi transfer
spi/spi-bfin5xx: fix reversed if condition in interrupt mode
spi/spi_bfin_sport: drop bits_per_word from client data
spi/bfin_spi: drop bits_per_word from client data
spi/spi-bfin-sport: move word length setup to transfer handler
spi/bfin5xx: rename config macro name for bfin5xx spi controller driver
spi/pl022: Allow request for higher frequency than maximum possible
spi/bcm63xx: set master driver mode_bits.
spi/bcm63xx: don't use the stopping state
spi/bcm63xx: convert to the pump message infrastructure
spi/spi-ep93xx.c: use dma_transfer_direction instead of dma_data_direction
spi: fix spi.h kernel-doc warning
spi/pl022: Fix calculate_effective_freq()
spi/pl022: Fix range checking for bits per word
Pull drm fixes from Dave Airlie:
"For your Friday pull request stack, nothing astounding or shattering
this week some exynos, some intel, some radeon fixes. One intel fix
for a regression somwehere back in 2.6.35 land."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: use frac fb div on APUs
drm/radeon: add a missing entry to encoder_names
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
drm/i915: fixup load-detect on enabled, but not active pipe
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Use x2apic physical mode based on FADT setting
x86/mrst: Quiet sparse noise about plain integer as NULL pointer
x86, intel_cacheinfo: Fix error return code in amd_set_l3_disable_slot()
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_for_each() to use sibling
perf symbols: Read plt symbols from proper symtab_type binary
tracing: Fix stacktrace of latency tracers (irqsoff and friends)
perf tools: Add 'G' and 'H' modifiers to event parsing
tracing: Fix regression with tracing_on
perf tools: Drop CROSS_COMPILE from flex and bison calls
perf report: Fix crash showing warning related to kernel maps
tracing: Fix build breakage without CONFIG_PERF_EVENTS (again)
Pull build fixes for less mainstream architectures from Paul Gortmaker:
"These are fixes for frv(1), blackfin(2), powerpc(1) and xtensa(4).
Fortunately the touches are nearly all specific to files just used by
the arch in question. The two touches to shared/common files
[kernel/irq/debug.h and drivers/pci/Makefile] are trivial to assess as
no risk to anyone.
Half of them relate to xtensa directly. It was only when I fixed the
last xtensa issue that I realized that the arch has been broken for a
significant time, and isn't a specific v3.4 regression. So if you
wanted, we could leave xtensa lying bleeding in the street for a
couple more weeks and queue those for 3.5. But given they are no risk
to anyone outside of xtensa, I figured to just leave them in.
If you are OK with taking the xtensa fixes, then please pull to get:
- one last implicit include uncovered by system.h that is in a file
specific to just one powerpc defconfig. (I'd sync'd with BenH).
- fix an oversight in the PCI makefile where shared code wasn't being
compiled for ARCH=frv
- fix a missing include for GPIO in blackfin framebuffer.
- audit and tag endif in blackfin ezkit board file, in order to find
and fix the misplaced endif masking a block of code.
- fix irq/debug.h choice of temporary macro names to be more internal
so they don't conflict with names used by xtensa.
- fix a reference to an undeclared local var in xtensa's signal.c
- fix an implicit bug.h usage in xtensa's asm/io.h uncovered by my
removing bug.h from kernel.h
- fix xtensa to properly indicate it is using asm-generic/hardirq.h
in order to resolve the link error - undefined ack_bad_irq
The xtensa still fails final link as my latest binutils does something
evil when ld forward-relocates unlikely() blocks, but in theory people
who have older/valid toolchains could now use the thing."
* 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
xtensa: fix build fail on undefined ack_bad_irq
blackfin: fix ifdef fustercluck in mach-bf538/boards/ezkit.c
blackfin: fix compile error in bfin-lq035q1-fb.c
pci: frv architecture needs generic setup-bus infrastructure
irq: hide debug macros so they don't collide with others.
xtensa: fix build error in xtensa/include/asm/io.h
xtensa: fix build failure in xtensa/kernel/signal.c
powerpc: fix system.h fallout in sysdev/scom.c [chroma_defconfig]
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up tracepoint build fallout from static key introduction.
sh: Fix error synchronising kernel page tables
Pull security key doc update from Jeff Layton:
"Ordinarily, I send my patches through others' trees, but David
suggested I just send this one to you directly since it's just a
Documentation/ update"
* 'docs-3.4' of git://git.samba.org/jlayton/linux:
keys: update the documentation with info about "logon" keys
In xen_restore_fl_direct(), xen_force_evtchn_callback() was being
called even if no events were pending. This resulted in (depending on
workload) about a 100 times as many xen_version hypercalls as
necessary.
Fix this by correcting the sense of the conditional jump.
This seems to give a significant performance benefit for some
workloads.
There is some subtle tricksy "..since the check here is trying to
check both pending and masked in a single cmpw, but I think this is
correct. It will call check_events now only when the combined
mask+pending word is 0x0001 (aka unmasked, pending)." (Ian)
CC: stable@kernel.org
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.
Fix this by freeing glue data last.
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 2a19032 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.
BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When our driver device is removed on the AHB bus, our IO memory is never unmapped.
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're spending huge amounts of time on lock contention during
end_io processing because we unconditionally assume we are overwriting
an existing extent in the file for each IO.
This checks to see if we are outside i_size, and if so, it uses a
less expensive readonly search of the btree to look for existing
extents.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs has an optimization where it will preallocate dentries during
readdir to fill in enough information to open the inode without an extra
lookup.
But, we're calling d_alloc, which is doing GFP_KERNEL allocations, and
that leads to deadlocks because our readdir code has tree locks held.
For now, disable this optimization. We'll fix the gfp mask in the next
merge window.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This condition is used to determine 8 bits or 16 and 32 bits transfer.
Obviously it is reversed.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The authflavor is set in an nfs_clone_mount structure and passed to the
xdev_mount() functions where it was promptly ignored. Instead, use it
to initialize an rpc_clnt for the cloned server.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I create a new proc_lookup_mountpoint() to use when submounting an NFS
v4 share. This function returns an rpc_clnt to use for performing an
fs_locations() call on a referral's mountpoint.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Whenever lookup sees wrongsec do a secinfo and retry the lookup to find
attributes of the file or directory, such as "is this a referral
mountpoint?". This also allows me to remove handling -NFS4ERR_WRONSEC
as part of getattr xdr decoding.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We don't want to return -NFS4ERR_WRONGSEC to the VFS because it could
cause the kernel to oops.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I was using the same decoder function for SECINFO and SECINFO_NO_NAME,
so it was returning an error when it tried to decode an OP_SECINFO_NO_NAME
header as OP_SECINFO.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
v2: recursion was replaced by loop
If client is a clone, then it's parent can not be in the list.
But parent's Pipefs dentries have to be created and destroyed.
Note: event skip helper for clients introduced
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There can be a case, when on MOUNT event RPC client (after it's dentries were
created) is not longer hold by anyone except notification callback.
I.e. on release this client will be destoroyed. And it's dentries have to be
destroyed as well. Which in turn requires per-net PipeFS superblock to be set.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
1) This is sane.
2) Otherwise there will be soft lockup:
do {
rpc_get_client_for_event (clnt->cl_dentry == NULL ==> choose)
__rpc_pipefs_event (clnt->cl_program->pipe_dir_name == NULL ==> return)
} while (1)
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When attempting to cache ACLs returned from the server, if the bitmap
size + the ACL size is greater than a PAGE_SIZE but the ACL size itself
is smaller than a PAGE_SIZE, we can read past the buffer page boundary.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reported-by: Jian Li <jiali@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix out-of-space checking, addressing a warning and potential resource
leak when resizing the filesystem down while allocating blocks.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
may_commit_transaction() calls
spin_lock(&space_info->lock);
spin_lock(&delayed_rsv->lock);
and update_global_block_rsv() calls
spin_lock(&block_rsv->lock);
spin_lock(&sinfo->lock);
Lockdep complains about this at run time.
Everywhere except in update_global_block_rsv(), the space_info lock is
the outer lock, therefore the locking order in update_global_block_rsv()
is changed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
I was seeing root_list corruption on unmount during fs resize in 3.4-rc4; add
correct locking to address this.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_map_block sets mirror_num, so that the repair code knows eventually
which device gave us the read error. For RAID10, mirror_num must be 1 or 2.
Before this fix mirror_num was incorrectly related to our stripe index.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_start_delalloc_inodes will just walk the list of delalloc inodes and
start writing them out, but it doesn't splice the list or anything so as
long as somebody is doing work on the box you could end up in this section
_forever_. So just remove it, it's not needed anyway since sync will start
writeback on all inodes anyway, all we need to do is wait for ordered
extents and then we can commit the transaction. In my horrible torture test
sync goes from taking 4 minutes to about 1.5 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bug noticed in commit
bf118a342f
When calling GETACL, if the size of the bitmap array, the length
attribute and the acl returned by the server is greater than the
allocated buffer(args.acl_len), we can Oops with a General Protection
fault at _copy_from_pages() when we attempt to read past the pages
allocated.
This patch allocates an extra PAGE for the bitmap and checks to see that
the bitmap + attribute_length + ACLs don't exceed the buffer space
allocated to it.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reported-by: Jian Li <jiali@redhat.com>
[Trond: Fixed a size_t vs unsigned int printk() warning]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix kernel-doc warning in spi.h (copy/paste):
Warning(include/linux/spi/spi.h:365): No description found for parameter 'unprepare_transfer_hardware'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb: fixes for v3.4-rc cycle
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
BIOS will switch off the corresponding feature flag on family
15h models 10h-1fh non-desktop CPUs.
The topology extension CPUID leafs are required to detect which
cores belong to the same compute unit. (thread siblings mask is
set accordingly and also correct information about L1i and L2
cache sharing depends on this).
W/o this patch we wouldn't see which cores belong to the same
compute unit and also cache sharing information for L1i and L2
would be incorrect on such systems.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since the last fixes to this driver ensure now the queue termination is
done correctly, we can finally disable the queue after a transfer
without problems. The gain is that it will only be reenabled after the
next transfer is fully set up. Before, the queue was running all the
time and if the setup of the next message was interrupted by another
thread, an incomplete buffer could have been sent, padded with zeroes.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit
8ae8090c82 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From Daniel Vetter
- VGA load-detect fix. This bug seems to be as old as the load-detect code
(2.6.30), but needs stupid userspace (upowerd trying to detect
connectors on dpms-off outputs) to actually kill the machine. And
obviously a machine without VGA-hotplug, otherwise we don't do load
detect.
- 2 interger overflow fixes for unpriviledged ioctls from Xi Wang.
- Fix SDVO regression for low-res (pixelclock < 100MHz) digital outputs,
introduce in 2.6.36.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/i915: fixup load-detect on enabled, but not active pipe
From Inki Dae:
this patch set fixes gem allocation and mapping issue between user space and
physical memory region.
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-2.6-samsung:
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
Pins configured as input and have MFP_LPM_DRIVE_* flag set, can have a
wrong output value for some period of time (spike) during the suspend
sequence.
This can happen because the direction of the pins (GPDR) is set by
software and the output level is set by hardware (PGSR) at a later
stage.
Fix the above potential bug by setting the output levels first.
Also save the actual levels of the pins before the suspend and restore
them after the resume, but before the direction settings take place, so
the same bug as described above will not happen in the resume sequence.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output
must retain the output state in low power mode.
Currently, the pin direction configuration is overrided with values
in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting.
Fix the above bug and add some documentation to clarify the
MFP_LPM_KEEP_OUTPUT setting purpose.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
DEFINE_RES_MEM() takes the size of resource as a second argument,
not the end address. Passing end address leads to following error
in runtime during device registration:
sa1100-rtc: failed to claim resource 0
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
We did a similar check for the P-states but did not do it for
the C-states. What we want to do is ignore cases where the DSDT
has definition for sixteen CPUs, but the machine only has eight
CPUs and we get:
xen-acpi-processor: (CX): Hypervisor error (-22) for ACPI CPU14
Reported-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When we boot on a machine that can hotplug CPUs and we
are using 'dom0_max_vcpus=X' on the Xen hypervisor line
to clip the amount of CPUs available to the initial domain,
we get this:
(XEN) Command line: com1=115200,8n1 dom0_mem=8G noreboot dom0_max_vcpus=8 sync_console mce_verbosity=verbose console=com1,vga loglvl=all guest_loglvl=all
.. snip..
DMI: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x032.072520111118 07/25/2011
.. snip.
SMP: Allowing 64 CPUs, 32 hotplug CPUs
installing Xen timer for CPU 7
cpu 7 spinlock event irq 361
NMI watchdog: disabled (cpu7): hardware events not enabled
Brought up 8 CPUs
.. snip..
[acpi processor finds the CPUs are not initialized and starts calling
arch_register_cpu, which creates /sys/devices/system/cpu/cpu8/online]
CPU 8 got hotplugged
CPU 9 got hotplugged
CPU 10 got hotplugged
.. snip..
initcall 1_acpi_battery_init_async+0x0/0x1b returned 0 after 406 usecs
calling erst_init+0x0/0x2bb @ 1
[and the scheduler sticks newly started tasks on the new CPUs, but
said CPUs cannot be initialized b/c the hypervisor has limited the
amount of vCPUS to 8 - as per the dom0_max_vcpus=8 flag.
The spinlock tries to kick the other CPU, but the structure for that
is not initialized and we crash.]
BUG: unable to handle kernel paging request at fffffffffffffed8
IP: [<ffffffff81035289>] xen_spin_lock+0x29/0x60
PGD 180d067 PUD 180e067 PMD 0
Oops: 0002 [#1] SMP
CPU 7
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.4.0-rc2upstream-00001-gf5154e8 #1 Intel Corporation S2600CP/S2600CP
RIP: e030:[<ffffffff81035289>] [<ffffffff81035289>] xen_spin_lock+0x29/0x60
RSP: e02b:ffff8801fb9b3a70 EFLAGS: 00010282
With this patch, we cap the amount of vCPUS that the initial domain
can run, to exactly what dom0_max_vcpus=X has specified.
In the future, if there is a hypercall that will allow a running
domain to expand past its initial set of vCPUS, this patch should
be re-evaluated.
CC: stable@kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
With the introduction of static keys, anything using tracepoints blows up
in the following manner:
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update')
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update.key')
This is a result of the STATIC_KEY_INIT_xxx defs wrapping ATOMIC_INIT()
which on sh includes an atomic_t typecast. Given that we don't really
need the typecast for anything anymore, the simplest solution is simply
to kill off the cast.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/3363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull arch/tile fixes from Chris Metcalf:
"One change fixes a platform-independent bug about environment var
handling in the boot command line. The other is a trivial
tile-specific bug fix to avoid a link-time warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix a couple of functions that should be __init
init: fix bug where environment vars can't be passed via boot args
Pull infiniband fixes from Roland Dreier:
"A few fixes for regressions introduced in 3.4-rc1:
- fix memory leak in mlx4
- fix two problems with new MAD response generation code"
* tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix memory leaks in ib_link_query_port()
IB/mad: Don't send response for failed MADs
IB/mad: Set 'D' bit in response for unhandled MADs
Commit e520c41085
"xtensa: convert to asm-generic/hardirq.h"
converted over to using the asm-generic parts, but it also
added the sentinel
#define ack_bad_irq ack_bad_irq
which tells asm-generic to _not_ use the common ack_bad_irq.
Since e520c41 deleted the duplicated code from the arch specific
file, we _do_ want the asm-generic one in scope. So delete
the trigger define above which hides it. In doing so we'll
realize that we've got to delete the almost-duplicate prototype
as well to avoid "static declaration ... follows non-static".
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull sound fixes from Takashi Iwai:
"A workaround for an ASUS laptop and a few ASoC changes; most of the
commits are tagged for stable, too."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Improve sequencing of AIF channel enables
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
ASoC: core: Fix card RTD count for deferred probe.
ASoC: cs42l73: don't use negative array index
ASoC: dapm: Ensure power gets managed for line widgets
Pull a watchdog fix from Wim Van Sebroeck:
"It will fix the size when reading or writing to WD Timer port 0x72 in
the hpwdt driver."
* git://www.linux-watchdog.org/linux-watchdog:
hpwdt: Only BYTE reads/writes to WD Timer port 0x72
Pull timer fixes from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix the spurious broadcast timer ticks after resume
tick: Ensure that the broadcast device is initialized
tick: Fix oneshot broadcast setup really
Merge fixes from Andrew Morton:
"13 fixes. The acerhdf patches aren't (really) fixes. But they've
been stuck in my tree for up to two years, sent to Matthew multiple
times and the developers are unhappy."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (13 patches)
mm: fix NULL ptr dereference in move_pages
mm: fix NULL ptr dereference in migrate_pages
revert "proc: clear_refs: do not clear reserved pages"
drivers/rtc/rtc-ds1307.c: fix BUG shown with lock debugging enabled
arch/arm/mach-ux500/mbox-db5500.c: world-writable sysfs fifo file
hugetlbfs: lockdep annotate root inode properly
acerhdf: lowered default temp fanon/fanoff values
acerhdf: add support for new hardware
acerhdf: add support for Aspire 1410 BIOS v1.3314
fs/buffer.c: remove BUG() in possible but rare condition
mm: fix up the vmscan stat in vmstat
epoll: clear the tfile_check_list on -ELOOP
mm/hugetlb: fix warning in alloc_huge_page/dequeue_huge_page_vma
In pirq_check_eoi_map use the pirq number rather than the Linux irq
number to check whether an eoi is needed in the pirq_eoi_map.
The reason is that the irq number is not always identical to the
pirq number so if we wrongly use the irq number to check the
pirq_eoi_map we are going to check for the wrong pirq to EOI.
As a consequence some interrupts might not be EOI'ed by the
guest correctly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Tobias Geiger <tobias.geiger@vido.info>
[v1: Added some extra wording to git commit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There are exactly four users of __monitor and __mwait:
- cstate.c (which allows acpi_processor_ffh_cstate_enter to be called
when the cpuidle API drivers are used. However patch
"cpuidle: replace xen access to x86 pm_idle and default_idle"
provides a mechanism to disable the cpuidle and use safe_halt.
- smpboot (which allows mwait_play_dead to be called). However
safe_halt is always used so we skip that.
- intel_idle (same deal as above).
- acpi_pad.c. This the one that we do not want to run as we
will hit the below crash.
Why do we want to expose MWAIT_LEAF in the first place?
We want it for the xen-acpi-processor driver - which uploads
C-states to the hypervisor. If MWAIT_LEAF is set, the cstate.c
sets the proper address in the C-states so that the hypervisor
can benefit from using the MWAIT functionality. And that is
the sole reason for using it.
Without this patch, if a module performs mwait or monitor we
get this:
invalid opcode: 0000 [#1] SMP
CPU 2
.. snip..
Pid: 5036, comm: insmod Tainted: G O 3.4.0-rc2upstream-dirty #2 Intel Corporation S2600CP/S2600CP
RIP: e030:[<ffffffffa000a017>] [<ffffffffa000a017>] mwait_check_init+0x17/0x1000 [mwait_check]
RSP: e02b:ffff8801c298bf18 EFLAGS: 00010282
RAX: ffff8801c298a010 RBX: ffffffffa03b2000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff8801c29800d8 RDI: ffff8801ff097200
RBP: ffff8801c298bf18 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: ffffffffa000a000 R14: 0000005148db7294 R15: 0000000000000003
FS: 00007fbb364f2700(0000) GS:ffff8801ff08c000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000179f038 CR3: 00000001c9469000 CR4: 0000000000002660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process insmod (pid: 5036, threadinfo ffff8801c298a000, task ffff8801c29cd7e0)
Stack:
ffff8801c298bf48 ffffffff81002124 ffffffffa03b2000 00000000000081fd
000000000178f010 000000000178f030 ffff8801c298bf78 ffffffff810c41e6
00007fff3fb30db9 00007fff3fb30db9 00000000000081fd 0000000000010000
Call Trace:
[<ffffffff81002124>] do_one_initcall+0x124/0x170
[<ffffffff810c41e6>] sys_init_module+0xc6/0x220
[<ffffffff815b15b9>] system_call_fastpath+0x16/0x1b
Code: <0f> 01 c8 31 c0 0f 01 c9 c9 c3 00 00 00 00 00 00 00 00 00 00 00 00
RIP [<ffffffffa000a017>] mwait_check_init+0x17/0x1000 [mwait_check]
RSP <ffff8801c298bf18>
---[ end trace 16582fc8a3d1e29a ]---
Kernel panic - not syncing: Fatal exception
With this module (which is what acpi_pad.c would hit):
MODULE_AUTHOR("Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>");
MODULE_DESCRIPTION("mwait_check_and_back");
MODULE_LICENSE("GPL");
MODULE_VERSION();
static int __init mwait_check_init(void)
{
__monitor((void *)¤t_thread_info()->flags, 0, 0);
__mwait(0, 0);
return 0;
}
static void __exit mwait_check_exit(void)
{
}
module_init(mwait_check_init);
module_exit(mwait_check_exit);
Reported-by: Liu, Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The current condition is always true, so everything uses
LOGICAL_DEV_CIR_REV2 (8). It should be that Fintek products
0x0408(F71809) and 0x0804(F71855) use logical device
LOGICAL_DEV_CIR_REV1 (5) and other chip ids use logical device 8.
In other words, this fixes hardware detection for 0x0408 and 0x0804.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file has lots and lots of ifdef, around structure decls
and structure usages. The failure issue was that we would
build the BF538-EZKIT_defconfig and get:
arch/blackfin/mach-bf538/boards/ezkit.c:924:3: error: 'bfin_lq035q1_device'
undeclared here (not in a function)
even though the same ifdef _appeared_ to enable both the struct
declaration and the code that used it. Yet cpp was telling us we
didn't have the struct, but we still had the usage of it.
However, _appeared_ is the operative word. After marking all the
anonymous #endif with their parent #ifdef config options, it was
_then_ clear that there was a misplaced #endif that was hiding
the struct declaration.
The real guts of the patch boils down to this:
-#endif
+#endif /* CONFIG_MTD_M25P80 */
+#endif /* CONFIG_SPI_BFIN5XX */
[...]
-#endif /* spi master and devices */
but since I had to tag the #endif with their respective #ifdef
options to find this misplaced SPI endif, it would be silly to
then go and delete them all. So they stay.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bob Liu <lliubbo@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file has an implicit dependency on GPIO stuff, showing
up as the following build failure:
drivers/video/bfin-lq035q1-fb.c:369:6: error: 'GPIOF_OUT_INIT_LOW' undeclared
Other more global bfin build issues prevent an automated bisect, but
it really doesn't matter - simply add in the appropriate header.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Otherwise we get this link failure for frv's defconfig:
LD .tmp_vmlinux1
drivers/built-in.o: In function `pci_assign_resource':
(.text+0xbf0c): undefined reference to `pci_cardbus_resource_alignment'
drivers/built-in.o: In function `pci_setup':
pci.c:(.init.text+0x174): undefined reference to `pci_realloc_get_opt'
pci.c:(.init.text+0x1a0): undefined reference to `pci_realloc_get_opt'
make[1]: *** [.tmp_vmlinux1] Error 1
Cc: David Howells <dhowells@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These controls have been marked for long time as V4L2_CID_HCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED in the DocBook and are going to be removed
from include/linux/videodev2.h.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An early registration of an ISR was causing a crash to several users (for
example, with the ite-cir driver: http://bugs.launchpad.net/bugs/972723).
The reason was that IRQs were being triggered before a driver
initialisation was completed.
This patch fixes this by moving the invocation to request_irq() and to
request_region() to a later stage on the driver probe function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
One of the OLPC changes lost a little in its translation to mainline,
leading to build errors on the ARM architecture. Remove the offending
line, and all will be well.
Reported-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We seem to have a decent confusion between the output timings and the
input timings of the sdvo encoder. If I understand the code correctly,
we use the original mode unchanged for the output timings, safe for
the lvds case. And we should use the adjusted mode for input timings.
Clarify the situation by adding an explicit output_dtd to the sdvo
mode_set function and streamline the code-flow by moving the input and
output mode setting in the sdvo encode together.
Furthermore testing showed that the sdvo input timing needs the
unadjusted dotclock, the sdvo chip will automatically compute the
required pixel multiplier to get a dotclock above 100 MHz.
Fix this up when converting a drm mode to an sdvo dtd.
This regression was introduced in
commit c74696b9c8
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 2 14:46:34 2010 -0400
i915: revert some checks added by commit 32aad86f
particularly the following hunk:
diff --git a/drivers/gpu/drm/i915/intel_sdvo.c
b/drivers/gpu/drm/i915/intel_sdvo.c
index 093e914..62d22ae 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -1122,11 +1123,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
/* We have tried to get input timing in mode_fixup, and filled into
adjusted_mode */
- if (intel_sdvo->is_tv || intel_sdvo->is_lvds) {
- intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ if (intel_sdvo->is_tv || intel_sdvo->is_lvds)
input_dtd.part2.sdvo_flags = intel_sdvo->sdvo_flags;
- } else
- intel_sdvo_get_dtd_from_mode(&input_dtd, mode);
/* If it's a TV, we already set the output timing in mode_fixup.
* Otherwise, the output timing is equal to the input timing.
Due to questions raised in review, below a more elaborate analysis of
the bug at hand:
Sdvo seems to have two timings, one is the output timing which will be
sent over whatever is connected on the other side of the sdvo chip (panel,
hdmi screen, tv), the other is the input timing which will be generated by
the gmch pipe. It looks like sdvo is expected to scale between the two.
To make things slightly more complicated, we have a bunch of special
cases:
- For lvds panel we always use a fixed output timing, namely
intel_sdvo->sdvo_lvds_fixed_mode, hence that special case.
- Sdvo has an interface to generate a preferred input timing for a given
output timing. This is the confusing thing that I've tried to clear up
with the follow-on patches.
- A special requirement is that the input pixel clock needs to be between
100MHz and 200MHz (likely to keep it within the electromechanical design
range of PCIe), 270MHz on later gen4+. Lower pixel clocks are
doubled/quadrupled.
The thing this patch tries to fix is that the pipe needs to be
explicitly instructed to double/quadruple the pixels and needs the
correspondingly higher pixel clock, whereas the sdvo adaptor seems to
do that itself and needs the unadjusted pixel clock. For the sdvo
encode side we already set the pixel mutliplier with a different
command (0x21).
This patch tries to fix this mess by:
- Keeping the output mode timing in the unadjusted plain mode, safe
for the lvds case.
- Storing the input timing in the adjusted_mode with the adjusted
pixel clock. This way we don't need to frob around with the core
crtc mode set code.
- Fixing up the pixelclock when constructing the sdvo dtd timing
struct. This is why the first hunk of the patch is an integral part
of the series.
- Dropping the is_tv special case because input_dtd is equivalent to
adjusted_mode after these changes. Follow-up patches clear this up
further (by simply ripping out intel_sdvo->input_dtd because it's
not needed).
v2: Extend commit message with an in-depth bug analysis.
Reported-and-Tested-by: Bernard Blackham <b-linuxgit@largestprime.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48157
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All referrals (IPv4 addr, IPv6 addr, and DNS) are broken on mounts of
IPv6 addresses, because validation code uses a path that is parsed
from the dev_name ("<server>:<path>") by splitting on the first colon and
colons are used in IPv6 addrs.
This patch ignores colons within IPv6 addresses that are escaped by '[' and ']'.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If multiple clients are registered on a single camera host interface,
the user-space hot-plug software can try to access the one, that probed
first, before probing of the second one has completed. This can be
handled by individual host drivers, but it is even better to hold back
the user-space until all the probing on this host has completed. This
fixes a race on ecovec with two clients registered on the CEU1 host, which
otherwise triggers a BUG() in sh_mobile_ceu_remove_device().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is to correct the use of the iLO port 0x72 usage.
The port 0x72 is a byte size write/read and hpwdt is currently
writing a WORD.
Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In perf_event_for_each() we call a function on an event, and then
iterate over the siblings of the event.
However we don't call the function on the siblings, we call it
repeatedly on the original event - it seems "obvious" that we should
be calling it with sibling as the argument.
It looks like this broke in commit 75f937f24b ("Fix ctx->mutex
vs counter->mutex inversion").
The only effect of the bug is that the PERF_IOC_FLAG_GROUP parameter
to the ioctls doesn't work.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334109253-31329-1-git-send-email-michael@ellerman.id.au
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Under extreme memory used up situations, percpu allocation
might fail. We hit it when system goes to suspend-to-ram,
causing a kworker panic:
EIP: [<c124411a>] build_sched_domains+0x23a/0xad0
Kernel panic - not syncing: Fatal exception
Pid: 3026, comm: kworker/u:3
3.0.8-137473-gf42fbef #1
Call Trace:
[<c18cc4f2>] panic+0x66/0x16c
[...]
[<c1244c37>] partition_sched_domains+0x287/0x4b0
[<c12a77be>] cpuset_update_active_cpus+0x1fe/0x210
[<c123712d>] cpuset_cpu_inactive+0x1d/0x30
[...]
With this fix applied build_sched_domains() will return -ENOMEM and
the suspend attempt fails.
Signed-off-by: he, bo <bo.he@intel.com>
Reviewed-by: Zhang, Yanmin <yanmin.zhang@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1335355161.5892.17.camel@hebo
[ So, we fail to deallocate a CPU because we cannot allocate RAM :-/
I don't like that kind of sad behavior but nevertheless it should
not crash under high memory load. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commits 367456c756 ("sched: Ditch per cgroup task lists for
load-balancing") and 5d6523ebd ("sched: Fix load-balance wreckage")
left some more wreckage.
By setting loop_max unconditionally to ->nr_running load-balancing
could take a lot of time on very long runqueues (hackbench!). So keep
the sysctl as max limit of the amount of tasks we'll iterate.
Furthermore, the min load filter for migration completely fails with
cgroups since inequality in per-cpu state can easily lead to such
small loads :/
Furthermore the change to add new tasks to the tail of the queue
instead of the head seems to have some effect.. not quite sure I
understand why.
Combined these fixes solve the huge hackbench regression reported by
Tim when hackbench is ran in a cgroup.
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1335365763.28150.267.camel@twins
[ got rid of the CONFIG_PREEMPT tuning and made small readability edits ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Tested on my Beagle XM.
v2: added mantainer to the list of recipient
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dl2k driver's rio_ioctl call has a few issues:
- No permissions checking
- Implements SIOCGMIIREG and SIOCGMIIREG using the SIOCDEVPRIVATE numbers
- Has a few ioctls that may have been used for debugging at one point
but have no place in the kernel proper.
This patch removes all but the MII ioctls, renumbers them to use the
standard ones, and adds the proper permission check for SIOCSMIIREG.
We can also get rid of the dl2k-specific struct mii_data in favor of
the generic struct mii_ioctl_data.
Since we have the phyid on hand, we can add the SIOCGMIIPHY ioctl too.
Most of the MII code for the driver could probably be converted to use
the generic MII library but I don't have a device to test the results.
Reported-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean all the pending fragments and relative timers if 6lowpan link
is going to be deleted.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nescesary mlme callbacks to satisfy "iz list" request from user space.
Due to 6lowpan device doesn't have its own phy, mlme implemented as a pipe
to a real phy to which 6lowpan is attached.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Loard pointed out:
"For example, this beauty from rtc-mpc5121.c in the same update:
...
rtc->rtc = rtc_device_register("mpc5200-rtc", &op->dev,
&mpc5200_rtc_ops, THIS_MODULE);
...
rtc->rtc->uie_unsupported = 1; // <<<< Ooops NULL pointer >>>>
if (IS_ERR(rtc->rtc)) { // <<<< this needs to be earlier >>>>
err = PTR_ERR(rtc->rtc);
goto out_free_irq;
}
..."
This patch moves setting the uie_unsupported flag to after we validate
the rtc->rtc pointer to resolve this.
Reported by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1335300215-21427-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit a4910b7444 has broken promiscuous
mode, which is never set. port->promisc just reflects the last setting
of PROMISCUOUS mode to avoid doing an extra hypercall when it's already
set.
However, since it may fail because of hypervisor permissions, we should
still respect the multicast settings and not simply exit after setting
promiscuous mode.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug in the mask of regtype parameter for registering a
multicast filter. It was ignoring the scope bit, which was wrongly being
used for all filters. The SCOPE_ALL value adds a filter that allows all
multicast packets and ignores the MAC parameter, just what allmulticast
needs. The normals filters, however, should not use SCOPE_ALL.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure net->ipvs is reset on netns cleanup or failed
initialization. It is needed for IPVS applications to know that
IPVS core is not loaded in netns.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Avoid crash when registering ip_vs_ftp after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Pull NFS client bugfixes from Trond Myklebust:
- Fix NFSv4 infinite loops on open(O_TRUNC)
- Fix an Oops and an infinite loop in the NFSv4 flock code
- Don't register the PipeFS filesystem until it has been set up
- Fix an Oops in nfs_try_to_update_request
- Don't reuse NFSv4 open owners: fixes a bad sequence id storm.
* tag 'nfs-for-3.4-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Keep dropped state owners on the LRU list for a while
NFSv4: Ensure that we don't drop a state owner more than once
NFSv4: Ensure we do not reuse open owner names
nfs: Enclose hostname in brackets when needed in nfs_do_root_mount
NFS: put open context on error in nfs_flush_multi
NFS: put open context on error in nfs_pagein_multi
NFSv4: Fix open(O_TRUNC) and ftruncate() error handling
NFSv4: Ensure that we check lock exclusive/shared type against open modes
NFSv4: Ensure that the LOCK code sets exception->inode
NFS: check for req==NULL in nfs_try_to_update_request cleanup
SUNRPC: register PipeFS file system after pernet sybsystem
* 'u300-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
Pull x86 fixes from H. Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x32, siginfo: Provide proper overrides for x32 siginfo_t
asm-generic: Allow overriding clock_t and add attributes to siginfo_t
x32: Check __ILP32__ instead of __LP64__ for x32
x86, acpi: Call acpi_enter_sleep_state via an asmlinkage C function from assembler
ACPI: Convert wake_sleep_flags to a value instead of function
x86, apic: APIC code touches invalid MSR on P5 class machines
i387: ptrace breaks the lazy-fpu-restore logic
x86/platform: Remove incorrect error message in x86_default_fixup_cpu_id()
x86, efi: Add dedicated EFI stub entry point
x86/amd: Remove broken links from comment and kernel message
x86, microcode: Ensure that module is only loaded on supported AMD CPUs
x86, microcode: Fix sysfs warning during module unload on unsupported CPUs
Pull x86 platform driver fixes from Matthew Garrett:
"One annoyance fix (make intel_ips stop complaining unnecessarily) and
one oops fix (unterminated list in dell-laptop). Both have been in
-next for a while with no complaints."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
dell-laptop: Terminate quirks list properly
intel_ips: Hush the i915 symbols message
Revert commit 85e72aa538 ("proc: clear_refs: do not clear reserved
pages"), which was a quick fix suitable for -stable until ARM had been
moved over to the gate_vma mechanism:
https://lkml.org/lkml/2012/1/14/55
With commit f9d4861f ("ARM: 7294/1: vectors: use gate_vma for vectors user
mapping"), ARM does now use the gate_vma, so the PageReserved check can be
removed from the proc code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Nicolas Pitre <nico@linaro.org>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct bin_attribute initialization to fix the following bug:
rtc-ds1307 3-0068: rtc core: registered ds1307 as rtc0
BUG: key cfb14fcc not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2986 sysfs_add_file_mode+0x84/0xdc()
Modules linked in:
[<c0018d94>] (unwind_backtrace+0x0/0xf8) from [<c0031f7c>] (warn_slowpath_common+0x4c/0x64)
[<c0031f7c>] (warn_slowpath_common+0x4c/0x64) from [<c0031fb0>] (warn_slowpath_null+0x1c/0x24)
[<c0031fb0>] (warn_slowpath_null+0x1c/0x24) from [<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc)
[<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc) from [<c04b11e4>] (ds1307_probe+0x5e4/0x6ac)
[<c04b11e4>] (ds1307_probe+0x5e4/0x6ac) from [<c036e600>] (i2c_device_probe+0xdc/0x108)
[<c036e600>] (i2c_device_probe+0xdc/0x108) from [<c02cdf84>] (driver_probe_device+0x90/0x210)
[<c02cdf84>] (driver_probe_device+0x90/0x210) from [<c02ce198>] (__driver_attach+0x94/0x98)
[<c02ce198>] (__driver_attach+0x94/0x98) from [<c02cc824>] (bus_for_each_dev+0x50/0x7c)
[<c02cc824>] (bus_for_each_dev+0x50/0x7c) from [<c02cd780>] (bus_add_driver+0x184/0x244)
[<c02cd780>] (bus_add_driver+0x184/0x244) from [<c02ce43c>] (driver_register+0x78/0x12c)
[<c02ce43c>] (driver_register+0x78/0x12c) from [<c03701ac>] (i2c_register_driver+0x2c/0xb4)
[<c03701ac>] (i2c_register_driver+0x2c/0xb4) from [<c0008798>] (do_one_initcall+0x34/0x178)
[<c0008798>] (do_one_initcall+0x34/0x178) from [<c0691860>] (kernel_init+0xdc/0x194)
[<c0691860>] (kernel_init+0xdc/0x194) from [<c0013cf0>] (kernel_thread_exit+0x0/0x8)
Since commit 6992f53349 ("sysfs: Use one lockdep class per sysfs
attribute") this initialization is required.
Reported-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the below reported false lockdep warning. e096d0c7e2
("lockdep: Add helper function for dir vs file i_mutex annotation") added
a similar annotation for every other inode in hugetlbfs but missed the
root inode because it was allocated by a separate function.
For HugeTLB fs we allow taking i_mutex in mmap. HugeTLB fs doesn't
support file write and its file read callback is modified in a05b0855fd
("hugetlbfs: avoid taking i_mutex from hugetlbfs_read()") to not take
i_mutex. Hence for HugeTLB fs with regular files we really don't take
i_mutex with mmap_sem held.
======================================================
[ INFO: possible circular locking dependency detected ]
3.4.0-rc1+ #322 Not tainted
-------------------------------------------------------
bash/1572 is trying to acquire lock:
(&mm->mmap_sem){++++++}, at: [<ffffffff810f1618>] might_fault+0x40/0x90
but task is already holding lock:
(&sb->s_type->i_mutex_key#12){+.+.+.}, at: [<ffffffff81125f88>] vfs_readdir+0x56/0xa8
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&sb->s_type->i_mutex_key#12){+.+.+.}:
[<ffffffff810a09e5>] lock_acquire+0xd5/0xfa
[<ffffffff816a2f5e>] __mutex_lock_common+0x48/0x350
[<ffffffff816a3325>] mutex_lock_nested+0x2a/0x31
[<ffffffff811fb8e1>] hugetlbfs_file_mmap+0x7d/0x104
[<ffffffff810f859a>] mmap_region+0x272/0x47d
[<ffffffff810f8a39>] do_mmap_pgoff+0x294/0x2ee
[<ffffffff810f8b65>] sys_mmap_pgoff+0xd2/0x10e
[<ffffffff8103d19e>] sys_mmap+0x1d/0x1f
[<ffffffff816a5922>] system_call_fastpath+0x16/0x1b
-> #0 (&mm->mmap_sem){++++++}:
[<ffffffff810a0256>] __lock_acquire+0xa81/0xd75
[<ffffffff810a09e5>] lock_acquire+0xd5/0xfa
[<ffffffff810f1645>] might_fault+0x6d/0x90
[<ffffffff81125d62>] filldir+0x6a/0xc2
[<ffffffff81133a83>] dcache_readdir+0x5c/0x222
[<ffffffff81125fa8>] vfs_readdir+0x76/0xa8
[<ffffffff811260b6>] sys_getdents+0x79/0xc9
[<ffffffff816a5922>] system_call_fastpath+0x16/0x1b
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sb->s_type->i_mutex_key#12);
lock(&mm->mmap_sem);
lock(&sb->s_type->i_mutex_key#12);
lock(&mm->mmap_sem);
*** DEADLOCK ***
1 lock held by bash/1572:
#0: (&sb->s_type->i_mutex_key#12){+.+.+.}, at: [<ffffffff81125f88>] vfs_readdir+0x56/0xa8
stack backtrace:
Pid: 1572, comm: bash Not tainted 3.4.0-rc1+ #322
Call Trace:
[<ffffffff81699a3c>] print_circular_bug+0x1f8/0x209
[<ffffffff810a0256>] __lock_acquire+0xa81/0xd75
[<ffffffff810f38aa>] ? handle_pte_fault+0x5ff/0x614
[<ffffffff8109e622>] ? mark_lock+0x2d/0x258
[<ffffffff810f1618>] ? might_fault+0x40/0x90
[<ffffffff810a09e5>] lock_acquire+0xd5/0xfa
[<ffffffff810f1618>] ? might_fault+0x40/0x90
[<ffffffff816a3249>] ? __mutex_lock_common+0x333/0x350
[<ffffffff810f1645>] might_fault+0x6d/0x90
[<ffffffff810f1618>] ? might_fault+0x40/0x90
[<ffffffff81125d62>] filldir+0x6a/0xc2
[<ffffffff81133a83>] dcache_readdir+0x5c/0x222
[<ffffffff81125cf8>] ? sys_ioctl+0x74/0x74
[<ffffffff81125cf8>] ? sys_ioctl+0x74/0x74
[<ffffffff81125cf8>] ? sys_ioctl+0x74/0x74
[<ffffffff81125fa8>] vfs_readdir+0x76/0xa8
[<ffffffff811260b6>] sys_getdents+0x79/0xc9
[<ffffffff816a5922>] system_call_fastpath+0x16/0x1b
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to new supported hardware, of which the actual temperature limits of
processor, harddisk and other components are unknown, it feels safer with
lower fanon / fanoff settings.
It won't change much for most people, already using acerhdf, as they use
their own fanon/fanoff variable settings when loading the module.
Furthermore seems like kernel and userspace tools have been improved to
work more efficient and netbooks don't get so hot anymore.
Signed-off-by: Peter Feuerer <peter@piie.net>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While stressing the kernel with with failing allocations today, I hit the
following chain of events:
alloc_page_buffers():
bh = alloc_buffer_head(GFP_NOFS);
if (!bh)
goto no_grow; <= path taken
grow_dev_page():
bh = alloc_page_buffers(page, size, 0);
if (!bh)
goto failed; <= taken, consequence of the above
and then the failed path BUG()s the kernel.
The failure is inserted a litte bit artificially, but even then, I see no
reason why it should be deemed impossible in a real box.
Even though this is not a condition that we expect to see around every
time, failed allocations are expected to be handled, and BUG() sounds just
too much. As a matter of fact, grow_dev_page() can return NULL just fine
in other circumstances, so I propose we just remove it, then.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "pgsteal" stat is confusing because it counts both direct reclaim as
well as background reclaim. However, we have "kswapd_steal" which also
counts background reclaim value.
This patch fixes it and also makes it match the existng "pgscan_" stats.
Test:
pgsteal_kswapd_dma32 447623
pgsteal_kswapd_normal 42272677
pgsteal_kswapd_movable 0
pgsteal_direct_dma32 2801
pgsteal_direct_normal 44353270
pgsteal_direct_movable 0
Signed-off-by: Ying Han <yinghan@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a gcc warning (and bug?) introduced in cc9a6c877 ("cpuset: mm: reduce
large amounts of memory barrier related damage v3")
Local variable "page" can be uninitialized if the nodemask from vma policy
does not intersects with nodemask from cpuset. Even if it doesn't happens
it is better to initialize this variable explicitly than to introduce
a kernel oops in a weird corner case.
mm/hugetlb.c: In function `alloc_huge_page':
mm/hugetlb.c:1135:5: warning: `page' may be used uninitialized in this function
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
None of the callsites actually need the page_cgroup descriptor
themselves, so just pass the page and do the look up in there.
We already had two bugs (6568d4a 'mm: memcg: update the correct soft
limit tree during migration' and 'memcg: fix Bad page state after
replace_page_cache') where the passed page and pc were not referring
to the same page frame.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The comments above __alloc_bootmem_node() claim that the code will
first try the allocation using 'goal' and if that fails it will
try again but with the 'goal' requirement dropped.
Unfortunately, this is not what the code does, so fix it to do so.
This is important for nobootmem conversions to architectures such
as sparc where MAX_DMA_ADDRESS is infinity.
On such architectures all of the allocations done by generic spots,
such as the sparse-vmemmap implementation, will pass in:
__pa(MAX_DMA_ADDRESS)
as the goal, and with the limit given as "-1" this will always fail
unless we add the appropriate fallback logic here.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we use netlink to monitor queue information for udp socket,
idiag_rqueue and idiag_wqueue of inet_diag_msg are returned with 0.
Keep consistent with netstat, just return back allocated rmem/wmem size.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After an error interrupt setting cmd->err, I see another interrupt that
the data engine is empty which clears cmd->err before being processed.
So, clear cmd->err at the beginning of a transfer only to handle these
consecutive interrupts.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 026cee0086 had the side-effect of dropping the '=' from
the unknown boot arguments that are passed to init as environment
variables. This is because parse_args() puts a NUL in the string
where the '=' was when it passes the "param" and "val" pointers
to the parsing subfunctions. Previously, unknown_bootoption() was
the last parse_args() subfunction to run, and it carefully put back
the '=' character. Now the ignore_unknown_bootoption() is the last
one to run, and it wasn't doing the necessary repair, so the
envp params ended up with the embedded NUL and were no longer
seen as valid environment variables by init.
Tested-by: Woody Suwalski <terraluna977@gmail.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
A small L3 cache index disable fix from Srivatsa Bhat which unifies the
way the code checks for already disabled indices.
( Pulling it into v3.4 despite the v3.5 tag - the fix is small and we better
keep the same code across kernel versions for such user facing interfaces. )
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 980b0bc69 ("ASoC: blackfin: Use dai_fmt") converted the blackfin ASoC
machine drivers to use the dai_links dai_fmt field to setup their DAI format.
For the bf5xx-ssm2602 the commit removed the manual call to snd_soc_dai_set_fmt,
but missed to set the dai_links dai_fmt field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a client calls pl08x_control with DMA_TERMINATE_ALL, it is correct
to terminate and release the phy channel currently in use (if one is in use),
but the phychan_hold counter must also be reset (otherwise it could get
trapped in an unbalanced state).
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Move a couple of tests and do a minor refactor to avoid:
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:2929:215: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/dma/pl330.c: In function 'pl330_tasklet':
drivers/dma/pl330.c:2250:8: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2228:25: note: 'pch' was declared here
drivers/dma/pl330.c:2277:130: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2260:25: note: 'pch' was declared here
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
commit 14e405461e (2.6.39)
("Add __ip_vs_control_{init,cleanup}_sysctl()")
introduced regression due to wrong __net_init for
__ip_vs_control_cleanup_sysctl. This leads to crash when
the ip_vs module is unloaded.
Fix it by changing __net_init to __net_exit for
the function that is already renamed to ip_vs_control_net_cleanup_sysctl.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.
This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on the original patch from Ying Cai <ycai@google.com>
This change ensures that the itr/itr_setting adjustment logic is used,
even for the default/compiled-in value.
Context:
When we changed the default InterruptThrottleRate value from default
(3 = dynamic mode) to 8000 for example, only adapter->itr_setting
(which controls interrupt coalescing mode) was set to 8000, but
adapter->itr (which controls the value set in NIC register) was not
updated accordingly. So from ethtool, it seemed the interrupt
throttling is enabled at 8000 intr/s, but the NIC actually was
running in dynamic mode which has lower CPU efficiency especially
when throughput is not high.
CC: Ying Cai <ycai@google.com>
CC: David Decotigny <david.decotigny@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Following logs where seen on Systems with multiple NICs,
while using MSI interrupts as shown below:
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0d.0: lan0_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: wan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.notice kernel: 0000:40:0d.0: lan0_1: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:32 (none) user.warn kernel: 0000:40:0e.0: wan4_0: MSI interrupt
test failed, using legacy interrupt.
Feb 16 15:09:32 (none) user.notice kernel: 0000:00:0e.0: wan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0e.0: lan1_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: wan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:00:0f.0: lan2_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: wan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:33 (none) user.notice kernel: 0000:40:0a.0: lan3_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0e.0: lan4_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: wan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
Feb 16 15:09:34 (none) user.notice kernel: 0000:40:0f.0: lan5_0: NIC Link is Up
1000 Mbps Full Duplex, Flow Control: RX/TX
This patch fixes this problem by increasing the msleep from 50 to 100.
Signed-off-by: Prasanna S Panchamukhi <ppanchamukhi@riverbed.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 6e8201f57c "mmc: core: add the capability for broken voltage"
introduced a new quirk to indicate that MMC core should ignore voltage
change errors reported by the regulators core. This is required to get
SDHCI working on UniversalC210, NURI and GONI boards again after commit
ceb6143b2d ("mmc: sdhci: fix vmmc handling").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If the call to mlx4_MAD_IFC() fails in ib_link_query_port() we will
currently do 'return err;' which will leak 'in_mad' and 'out_mad'. We
should instead do 'goto out;' where we'll properly free the memory we
previously allocated.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 0b30704304 ("IB/mad: Return error response for unsupported
MADs") does not failed MADs (eg those that return
IB_MAD_RESULT_FAILURE) properly -- these MADs should be silently
discarded. (We should not force the lower-layer drivers to return
SUCCESS | CONSUMED in this case, since the MAD is NOT successful).
Unsupported MADs are not failures -- they return SUCCESS, but with an
"unsupported error" status value inside the response MAD.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 0b30704304 ("IB/mad: Return error response for unsupported
MADs") does not handle directed-route MADs properly -- it fails to set
the 'D' bit in the response MAD status field. This is a problem for
SmInfo MADs when the receiver does not have an SM running.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hibernation regression fix, since 3.2.
Calculate the number of required free pages based on non-high memory
pages only, because that is where the buffers will come from.
Commit 081a9d043c introduced a new buffer
page allocation logic during hibernation, in order to improve the
performance. The amount of pages allocated was calculated based on total
amount of pages available, although only non-high memory pages are
usable for this purpose. This caused hibernation code to attempt to over
allocate pages on platforms that have high memory, which led to hangs.
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@suse.de>
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed following compile time error.
arch/arm/mach-exynos/common.c: In function 'exynos5_init_irq':
arch/arm/mach-exynos/common.c:539:2: error: implicit declaration of function 'of_irq_init'
arch/arm/mach-exynos/common.c:539:14: error: 'exynos4_dt_irq_match' undeclared (first use in this function)
arch/arm/mach-exynos/common.c:539:14: note: each undeclared identifier is reported only once for each function it appears in
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Should be EXYNOS4_IRQ_DWMCI instead of IRQ_DWMCI,
and use DEFINE_RES_{MEM,IRQ}.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
warning: (CPU_S3C2440 && CPU_S3C2442) selects S3C2410_PM which has unmet direct dependencies (ARCH_S3C24XX && CPU_S3C2410)
warning: (CPU_S3C2440 && CPU_S3C2442) selects S3C2410_PM which has unmet direct dependencies (ARCH_S3C24XX && CPU_S3C2410)
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed to fix mini2440_defconfig after the platform
files have been moved around.
arm-none-linux-gnueabi-ld: no machine record defined
arm-none-linux-gnueabi-ld: no machine record defined
arm-none-linux-gnueabi-ld: no machine record defined
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following build failures:
drivers/staging/octeon/ethernet.c: In function 'cvm_oct_cleanup_module':
drivers/staging/octeon/ethernet.c:799:2: error: implicit declaration of function 'free_irq'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_no_more_work':
drivers/staging/octeon/ethernet-rx.c:119:3: error: implicit declaration of function 'enable_irq'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_do_interrupt':
drivers/staging/octeon/ethernet-rx.c:136:2: error: implicit declaration of function 'disable_irq_nosync'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_rx_initialize':
drivers/staging/octeon/ethernet-rx.c:532:2: error: implicit declaration of function 'request_irq'
drivers/staging/octeon/ethernet-tx.c: In function 'cvm_oct_tx_initialize':
drivers/staging/octeon/ethernet-tx.c:712:2: error: implicit declaration of function 'request_irq'
drivers/staging/octeon/ethernet-tx.c: In function 'cvm_oct_tx_shutdown':
drivers/staging/octeon/ethernet-tx.c:723:2: error: implicit declaration of function 'free_irq'
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZCACHE is a boolean in the Kconfig. When selected, it
should require that CRYPTO be builtin (=y).
Currently, ZCACHE=y and CRYPTO=m is a valid configuration
when it should not be.
This patch changes the zcache Kconfig to enforce this
dependency.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead now use ioremap. This is needed for 3.4 since this change
emerged in mainline during one of the previous rc cycles.
These solves the following compilation breaks:
drivers/staging/tidspbridge/core/tiomap3430.c:
In function ‘bridge_brd_start’:
drivers/staging/tidspbridge/core/tiomap3430.c:425:4:
error: implicit declaration of function ‘OMAP2_L4_IO_ADDRESS’
drivers/staging/tidspbridge/core/wdt.c: In function ‘dsp_wdt_init’:
drivers/staging/tidspbridge/core/wdt.c:56:2:
error: implicit declaration of function ‘OMAP2_L4_IO_ADDRESS’
For control registers a new function needs to be defined so we
can get rid of a layer violation, but that approach must be queued
for the next merge window.
As seen in:
http://www.arm.linux.org.uk/developer/build/
platform: omap4430-sdp build: uImage
config: randconfig version: 3.4.0-rc3
start time: Apr 20 2012 01:07
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cifs_show_options uses the wrong conversion specifier for uid, gid,
rsize & wsize. Correct this to %u to match it to the variable type
'unsigned integer'.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Show backupuid/backupgid in /proc/mounts for cifs shares mounted with
the backupuid/backupgid feature.
Also consolidate the two separate checks for
pvolume_info->backupuid_specified into a single if condition in
cifs_setup_cifs_sb().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull HSI fixes and ABI documentation from Carlos Chinea
* tag 'hsi_fixes_for_3.4' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: Add HSI ABI documentation
HSI: hsi_char: Remove max_data_size from sysfs
HSI: hsi: Rework hsi_event interface
HSI: hsi: Remove controllers and ports from the bus
HSI: hsi: Fix error path cleanup on client registration
HSI: hsi: Rework hsi_controller release
Command complete event for HCI_OP_USER_PASSKEY_NEG_REPLY would result
in calling handler function also for HCI_OP_LE_SET_SCAN_PARAM. This
could result in undefined behaviour.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch instructs DLM to prevent an "in place" conversion, where the
lock just stays on the granted queue, and instead forces the conversion to
the back of the convert queue. This is done on upward conversions only.
This is useful in cases where, for example, a lock is frequently needed in
PR on one node, but another node needs it temporarily in EX to update it.
This may happen, for example, when the rindex is being updated by gfs2_grow.
The gfs2_grow needs to have the lock in EX, but the other nodes need to
re-read it to retrieve the updates. The glock is already granted in PR on
the non-growing nodes, so this prevents them from continually re-granting
the lock in PR, and forces the EX from gfs2_grow to go through.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: set fake_rtable's dst to NULL to avoid kernel Oops
when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.
v4 reformat, change br_drop_fake_rtable(skb) to {}
v3 enrich commit header
v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.
[ Use "do { } while (0)" for nop br_drop_fake_rtable()
implementation -DaveM ]
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Huang <peter.huangpeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ext4 bug fixes from Ted Ts'o:
"These are two low-risk bug fixes for ext4, fixing a compile warning
and a potential deadlock."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
super.c: unused variable warning without CONFIG_QUOTA
jbd2: use GFP_NOFS for blkdev_issue_flush
Pull Hexagon fixes from Richard Kuo:
"It's mostly compile fixes and the Hexagon portion of a CPU hotplug
patch set."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
hexagon: add missing cpu.h include
hexagon/CPU hotplug: Add missing call to notify_cpu_starting()
hexagon: use renamed tick_nohz_idle_* functions
Hexagon: misc compile warning/error cleanup due to missing headers
Pull build system failure fix from Michal Marek:
"This fixes build failure with newer gcc that adds some internal
symbols that end in "__mod_*_device_table", but are not actually the
tables themselves."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Fix modpost failures in fedora 17
sb info is only checked with quota support.
fs/ext4/super.c: In function ‘parse_options’:
fs/ext4/super.c:1600:23: warning: unused variable ‘sbi’ [-Wunused-variable]
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
flush request is issued in transaction commit code path, so looks using
GFP_KERNEL to allocate memory for flush request bio falls into the classic
deadlock issue. I saw btrfs and dm get it right, but ext4, xfs and md are
using GFP.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
Pull dlm fixes from David Teigland:
"This includes one short patch fixing the behavior of the QUECVT flag,
which the gfs2 folks are waiting on."
* tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: fix QUECVT when convert queue is empty
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ken Chen <kenchen@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit c744a65c1e
md: don't set md arrays to readonly on shutdown.
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org
Reported-by: Christoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit 7bfec5f35c
md/raid5: If there is a spare and a want_replacement device, start replacement.
cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.
So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.
This fix is suitable for 3.3.y:
Cc: stable@vger.kernel.org
Reported-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Fix segfault caused by using rdev_for_each instead of rdev_for_each_safe
Commit dafb20fa34 mistakenly replaced a safe
iterator with an unsafe one when making some macro changes.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For the particular issue of x32, which shares code with i386 in the
handling of compat_siginfo_t, the use of a 64-bit clock_t bumps the
sigchld structure out of alignment, which triggers a messy cascade of
padding.
This was already handled on the kernel compat side, but it needs
handling on the user space side, which uses the generic header. To
make that possible:
1. Allow __kernel_clock_t to be overridden in struct siginfo;
2. Allow there to be attributes added to struct siginfo.
Reported-by: H.J. Lu <hjl.rools@gmail.com>
Cc: Bruce J. Beare <bruce.j.beare@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/CAMe9rOqF6Kh6-NK7oP0Fpzkd4SBAWU%2BG53hwBbSD4iA2UzyxuA@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
As of
commit 75294957be
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 14 14:06:57 2012 -0700
irq_domain: Remove 'new' irq_domain in favour of the ppc one
the ARM gic controller uses proper irq domains. Fix the MSM gic
initialization and DT so that it works again.
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Check __LP64__ isn't a reliable way to tell if we are compiling for x32
since __LP64__ isnn't specified by x86-64 psABI. Not all x86-64
compilers define __LP64__, which was added to GCC 3.3. The updated x32
psABI:
https://sites.google.com/site/x32abi/documents
definse _ILP32 and __ILP32__ for x32. GCC trunk and 4.7 branch have
been updated to define _ILP32 and __ILP32__ for x32. This patch
replaces __LP64__ check with __ILP32__.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On 32-bit systems, a large args->num_cliprects from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 432e58ed ("drm/i915: Avoid
allocation for execbuffer object list").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On 32-bit systems, a large args->buffer_count from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 8408c282 ("drm/i915:
First try a normal large kmalloc for the temporary exec buffers").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the
wake_sleep_flags is required when calling acpi_enter_sleep_state.
The assembler code in wakeup_*.S did not do that. One solution
is to call it from assembler and stick the wake_sleep_flags on
the stack (for 32-bit) or in %esi (for 64-bit). hpa and rafael
both suggested however to create a wrapper function to call
acpi_enter_sleep_state and call said wrapper function
("acpi_enter_s3") from assembler.
For 32-bit, the acpi_enter_s3 ends up looking as so:
push %ebp
mov %esp,%ebp
sub $0x8,%esp
movzbl 0xc1809314,%eax [wake_sleep_flags]
movl $0x3,(%esp)
mov %eax,0x4(%esp)
call 0xc12d1fa0 <acpi_enter_sleep_state>
leave
ret
And 64-bit:
movzbl 0x9afde1(%rip),%esi [wake_sleep_flags]
push %rbp
mov $0x3,%edi
mov %rsp,%rbp
callq 0xffffffff812e9800 <acpi_enter_sleep_state>
leaveq
retq
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
[v2: Remove extra assembler operations, per hpa review]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-3-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.
This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
While we need to clean up unused single ended line outputs we don't want
to do this if the outputs are in differential mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7b
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
ASoC: updates for 3.4
Slightly larger than normal - the DAPM fix is a "this should always have
worked" type of thing which is very clear and should have no impact on
systems that don't need it. The WM8994 fix is driver specific but
pretty important for that driver.
The QUECVT flag should not prevent conversions from
being granted immediately when the convert queue is
empty.
Signed-off-by: David Teigland <teigland@redhat.com>
The file kernel/irq/debug.h temporarily defines P, PS, PD
and then undefines them. However these names aren't really
"internal" enough, and collide with other more legit users
such as the ones in the xtensa arch, causing:
In file included from kernel/irq/internals.h:58:0,
from kernel/irq/irqdesc.c:18:
kernel/irq/debug.h:8:0: warning: "PS" redefined [enabled by default]
arch/xtensa/include/asm/regs.h:59:0: note: this is the location of the previous definition
Add a handful of underscores to do a better job of hiding these
temporary macros.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Caused by commit 6c03438ede
kernel.h: doesn't explicitly use bug.h, so don't include it.
This header uses bug.h so explicitly include it now that the
implicit presence was removed by 6c03438ed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Caused by commit 3785006ac3
"xtensa: don't mask signals if we fail to setup signal stack"
It assigns a return value to "ret", but there is no such variable
anywhere in scope. Create one.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Using coherent DMA memory with the OMAP DMA engine results in
unpredictable behaviour due to memory ordering issues; as things stand,
there is no guarantee that data written to coherent DMA memory will be
visible to the DMA hardware.
This is because the OMAP dma_write() accessor contains no barriers,
necessary on ARMv6 and above. The effect of this can be seen in comments
in the OMAP serial driver, which incorrectly talks about cache flushing
for the coherent DMA stuff.
Rather than adding barriers to the accessors, add it in the DMA support
code just before we enable DMA, and just after we disable DMA. This
avoids having barriers for every DMA register access.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMCI driver will not work without two IRQs since this is not
flagged as a single-irq variant. Looking through the complex IRQ
definition for the MMCI on the versatile (including an #if 1
statement forcing MMCI IRQ0 to the VIC) this appears to the the
correct IRQ number for both models.
Cc: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM PCS mandates that the length and stride bits of the fpscr are
cleared on entry to and return from a public interface. Although signal
handlers run asynchronously with respect to the interrupted function,
the handler itself expects to run as though it has been called like a
normal function.
This patch updates the state mirroring the VFP hardware before entry to
a signal handler so that it adheres to the PCS. Furthermore, we disable
VFP to ensure that we trap on any floating point operation performed by
the signal handler and synchronise the hardware appropriately. A check
is inserted after the signal handler to avoid redundant flushing if VFP
was not used.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The user VFP state must be preserved (subject to ucontext modifications)
across invocation of a signal handler and this is currently handled by
vfp_{preserve,restore}_context in signal.c
Since this code requires intimate low-level knowledge of the VFP state,
this patch moves it into vfpmodule.c.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 errata #588369 and #727915 require writes to the debug registers
of the cache controller to work around known problems. Writing these
registers on L220 may cause deadlock, so ensure that we only perform
this operation when we identify a PL310 at probe time.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The workaround for PL310 erratum #753970 can lead to deadlock on systems
with an L220 cache controller.
This patch makes the workaround effective only when the cache controller
is identified as a PL310 at probe time.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Erratum #326103 ("FSR write bit incorrect on a SWP to read-only memory")
only affects the ARM 1136 core prior to r1p0. The workaround
disassembles the faulting instruction to determine whether it was a read
or write access on all v6 cores.
An issue has been reported on the ARM 11MPCore whereby loading the
faulting instruction may happen in parallel with that page being
unmapped, resulting in a deadlock due to the lack of TLB broadcasting
in hardware:
http://lists.infradead.org/pipermail/linux-arm-kernel/2012-March/091561.html
This patch limits the workaround so that it is only used on affected
cores, which are known to be UP only. Other v6 cores can rely on the
FSR to indicate the access type correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A small fallout from Vinod's conversions to dma_transfer_direction,
this small comparison was done with a dma_data_direction instead.
Fix it by comparing against the correct enum.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The patch "ARM: amba: Remove AMBA level regulator support" breaks
the DMA40 driver since the <linux/amba/bus.h> header implicitly
included the regulator consumer header. So include it explicitly
and fix the build error.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
can be directly stopped by issuing a SUSPEND_REQ on the EE
bits. There is no need to suspend the physical channel and
restart it.
Also, the support for pre-V2 hw is discontinued.
EE bits for writing:
00: disable only if AS=11 or AS=00
01: enable
10: suspend_req only if AS=01 & EE=01 or EE=11
11: round / no change for writing
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
with this patch, if the memory region is physically non-continuous
then VM_MIXEDMAP is set to vm->vm_flags otherwise VM_PFNMAP.
we had missed this flag setting.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
this patch fixes the problem that the physical memory region to be mapped
to user space could be exceeded. if page fault address was placed at between
buffer start and end then memory region to be mapped would be exceeded.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
the gem was already allocated at gem allocation time but is allocated
at page fault handler so this patch fixes the problem that gem was
allocated one more time.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Remove max_data_size sysfs entry. Otherwise is possible
to have a buffer overrun if its value is increased after
the device is open.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Remove custom hack and make use of the notifier chain interfaces for
delivering events from the ports to their associated clients.
Clients that want to receive port events need to register their callbacks
using hsi_register_port_event(). The callbacks can be called in interrupt
context. Use hsi_unregestier_port_event() to undo the registration.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use the proper release mechanism for hsi_controller and
hsi_ports structures. Free the structures through their
associated device release callbacks.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit a692b0eec5.
Tom reports:
[ 8.741033] ------------[ cut here ]------------
[ 8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[ 8.741040] Hardware name: To Be Filled By O.E.M.
[ 8.741041] sysfs: cannot create duplicate filename
...and missing 2 out of 4 drives connected to mvsas. Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique. However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas. So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7. The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: Tom Rini <trini@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover(). The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change. When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled. So change
the code to skip the sas_address and change count updates when ata_eh is
active.
Cc: Jack Wang <jack_wang@usish.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 899fcf4 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]
...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull ARM fixes from Russell King:
"Here's my usual Sunday push, just for one revert which PeterZ hollered
about after last weeks push. Other than that, all seems strangely
quiet as far as fixes go in non-platform ARM land at the moment."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for powerpc. Note the addition to the generic
irq.h. This is part of a 3-patches regression fix for mpic due to
changes in how IRQ_TYPE_NONE is being handled. Thomas agreed to the
addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
replied with an Ack to the actual patch yet. I don't to wait much
longer with these patches tho."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mpic: Properly set default triggers
irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
powerpc/mpic: Fix confusion between hw_irq and virq
powerpc/pmac: Don't add_timer() twice
powerpc/eeh: Fix crash caused by null eeh_dev
powerpc/mpc85xx: add MPIC message dts node
powerpc/mpic_msgr: fix offset error when setting mer register
powerpc/mpic_msgr: add lock for MPIC message global variable
powerpc/mpic_msgr: fix compile error when SMP disabled
powerpc: fix build when CONFIG_BOOKE_WDT is enabled
powerpc/85xx: don't call of_platform_bus_probe() twice
Pull networking fixes from David Miller:
1) Fix namespace init and cleanup in phonet to fix some oopses, from
Eric W. Biederman.
2) Missing kfree_skb() in AF_KEY, from Julia Lawall.
3) Refcount leak and source address handling fix in l2tp from James
Chapman.
4) Memory leak fix in CAIF from Tomasz Gregorek.
5) When routes are cloned from ipv6 addrconf routes, we don't process
expirations properly. Fix from Gao Feng.
6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.
7) Only enable interrupts in 8139cp driver after we've registered the
IRQ handler. From Jason Wang.
8) Fix too many reads of KS_CIDER register in ks8851 during probe,
fixing crashes on spurious interrupts. From Matt Renzelmann.
9) Missing include in ath5k driver and missing iounmap on probe
failure, from Jonathan Bither.
10) Fix RX packet handling in smsc911x driver, from Will Deacon.
11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.
12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
buffers are easily overflown. Fix from Davide Cimingahi.
13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.
14) gred packet scheduler can dump in WRED more when doing a netlink
dump. Fix from David Ward.
15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.
16) Dummy device needs ->ndo_uninit handler to properly handle
->ndo_init failures. From Hiroaki SHIMODA.
17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.
18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.
19) Missing iounmap in farsync WAN driver, from Julia Lawall.
20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
the receive window properly, and this hurts performance. Fix from
Eric Dumazet.
21) Network namespace init failure can leak net_generic data, fix from
Julian Anastasov.
22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
SKBs. From Eric Dumazet.
23) New IDs for qmi_wwan driver, from Bjørn Mork.
24) Fix races in ax25_exit(), from Eric W. Biederman.
25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
logic from the IPV4 side. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: fix TCP_MAXSEG for established IPv6 passive sockets
drivers/net: Do not free an IRQ if its request failed
drop_monitor: allow more events per second
ks8851: Fix request_irq/free_irq mismatch
net/hyperv: Adding cancellation to ensure rndis filter is closed
ks8851: Fix mutex deadlock in ks8851_net_stop()
net ax25: Reorder ax25_exit to remove races.
icplus: fix interrupt for IC+ 101A/G and 1001LF
net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
ksz884x: don't copy too much in netdev_set_mac_address()
tcp: fix retransmit of partially acked frames
netns: do not leak net_generic data on failed init
net/sock.h: fix sk_peek_off kernel-doc warning
tcp: fix tcp_grow_window() for large incoming frames
drivers/net/wan/farsync.c: add missing iounmap
davinci_mdio: Fix MDIO timeout check
ipv6: clean up rt6_clean_expires
ipv6: fix rt6_update_expires
arcnet: rimi: Fix device name in debug output
...
The following build warning is seen in some configurations.
drivers/hwmon/ad7314.c: In function 'ad7314_show_temperature':
drivers/hwmon/ad7314.c:70: warning: 'data' may be used uninitialized in this function
Fix by overloading the return value from ad7314_spi_read with both data and
error code (the returned data is really u16 and needs to be converted into a
signed value anyway).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.
This in turn makes us read the HW state and update the irq desc
accordingly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).
The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.
However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.
Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.
The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.
The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, during i2c works alone, wait-event timeout is not occurred.
However, as CPU load increases, timeout occurs frequently.
So, I modified like this patch.
Modifying like this patch, I've never seen the timeout event with high
load test.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
NACK interrupt is generated before I2C controller generates the STOP
condition on bus. Because of this reset of controller is happening
before I2C controller could complete STOP condition. So wait for some
time before resetting the controller so that STOP condition has
delivered properly on bus.
Added delay of 2 clock period before resetting the controller in case of
NACK error.
Signed-off-by: Alok Chauhan <alokc@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[wsa: Reworded the commit msg and code comment a bit]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org
[wsa: reworded commit header slightly]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.
Since commit d139b9b([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.
Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Somehow we have a fast-path that tries to avoid going through
the load-detect code when the encode already has a crtc associated.
But this fails horribly when the crtc is off. The load detect pipe
itself manages this case well (and also does not forget to restore the
dpms state), so just rip out this special case.
The issue seems to go back all the way to the commit that originally
introduced load-detection on the vga output:
commit e4a5d54f92
Author: Ma Ling <ling.ma@intel.com>
Date: Tue May 26 11:31:00 2009 +0800
drm/i915: Add support for VGA load detection (pre-945).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43020
Reported-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems there is a logic error in trace_drop_common(), since we store
only 64 drops, even if they are from same location.
This fix is a one liner, but we probably need more work to avoid useless
atomic dec/inc
Now I can watch 1 Mpps drops through dropwatch...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_id parameter passed to free_irq needs to match the one passed
to the corresponding request_irq.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
Although the network interface is down, the RX packets number which
could be observed by ifconfig may keep on increasing.
This is because the WORK scheduled in netvsc_set_multicast_list()
may be executed after netvsc_close(). That means the rndis filter
may be re-enabled by do_set_multicast() even if it was closed by
netvsc_close().
By canceling possible WORK before close the rndis filter, the issue
could be never happened.
Signed-off-by: Wenqi Ma <wenqi_ma@trendmicro.com.cn>
Reviewed-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential deadlock scenario when the ks8851 driver
is removed. The interrupt handler schedules a workqueue which
acquires a mutex that ks8851_net_stop() also acquires before
flushing the workqueue. Previously lockdep wouldn't be able
to find this problem but now that it has the support we can
trigger this lockdep warning by rmmoding the driver after
an ifconfig up.
Fix the possible deadlock by disabling the interrupts in
the chip and then release the lock across the workqueue
flushing. The mutex is only there to proect the registers
anyway so this should be ok.
=======================================================
[ INFO: possible circular locking dependency detected ]
3.0.21-00021-g8b33780-dirty #2911
-------------------------------------------------------
rmmod/125 is trying to acquire lock:
((&ks->irq_work)){+.+...}, at: [<c019e0b8>] flush_work+0x0/0xac
but task is already holding lock:
(&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&ks->lock){+.+...}:
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c083dbec>] mutex_lock_nested+0x68/0x3dc
[<bf00bd48>] ks8851_irq_work+0x24/0x46c [ks8851]
[<c019c580>] process_one_work+0x2d8/0x518
[<c019cb98>] worker_thread+0x220/0x3a0
[<c01a2ad4>] kthread+0x88/0x94
[<c0107008>] kernel_thread_exit+0x0/0x8
-> #0 ((&ks->irq_work)){+.+...}:
[<c01b7984>] validate_chain+0x914/0x1018
[<c01b89c8>] __lock_acquire+0x940/0x9f8
[<c01b9058>] lock_acquire+0x10c/0x130
[<c019e104>] flush_work+0x4c/0xac
[<bf00b858>] ks8851_net_stop+0x6c/0x138 [ks8851]
[<c06b209c>] __dev_close_many+0x98/0xcc
[<c06b2174>] dev_close_many+0x68/0xd0
[<c06b22ec>] rollback_registered_many+0xcc/0x2b8
[<c06b2554>] rollback_registered+0x28/0x34
[<c06b25b8>] unregister_netdevice_queue+0x58/0x7c
[<c06b25f4>] unregister_netdev+0x18/0x20
[<bf00c1f4>] ks8851_remove+0x64/0xb4 [ks8851]
[<c049ddf0>] spi_drv_remove+0x18/0x1c
[<c0468e98>] __device_release_driver+0x7c/0xbc
[<c0468f64>] driver_detach+0x8c/0xb4
[<c0467f00>] bus_remove_driver+0xb8/0xe8
[<c01c1d20>] sys_delete_module+0x1e8/0x27c
[<c0105ec0>] ret_fast_syscall+0x0/0x3c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&ks->lock);
lock((&ks->irq_work));
lock(&ks->lock);
lock((&ks->irq_work));
*** DEADLOCK ***
4 locks held by rmmod/125:
#0: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f44>] driver_detach+0x6c/0xb4
#1: (&__lockdep_no_validate__){+.+.+.}, at: [<c0468f50>] driver_detach+0x78/0xb4
#2: (rtnl_mutex){+.+.+.}, at: [<c06b25e8>] unregister_netdev+0xc/0x20
#3: (&ks->lock){+.+...}, at: [<bf00b850>] ks8851_net_stop+0x64/0x138 [ks8851]
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retest the RB_EMPTY_NODE() condition under the spin lock
to ensure that we don't call rb_erase() more than once on the
same state owner.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
pfm_vm_munmap() is simply vm_munmap() and pfm_remove_smpl_mapping()
always get current as the first argument.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
commit 7968a5dd49
Input: synaptics - add support for Relative mode
Accidentally broke support for advanced gestures (multitouch)
on some trackpads such as the one in my ThinkPad X220 by
incorretly changing the condition for enabling them. This
restores it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org [3.3]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The NFSv4 spec is ambiguous about whether or not it is permissible
to reuse open owner names, so play it safe. This patch adds a timestamp
to the state_owner structure, and combines that with the IDA based
uniquifier.
Fixes a regression whereby the Linux server returns NFS4ERR_BAD_SEQID.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since SDIO drivers may want to do some SDIO operations in their suspend
callback functions, we must not keep the host claimed when calling them.
Daniel Drake reported that libertas_sdio encountered a deadlock in its
suspend function.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Tested-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.2-stable and 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.
If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the of_irq_init() call to setup the gic which also properly
registers the gic device node pointer with gic irq domain,
without which all interrupt specifier translations for gic fail.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This was broken by me in 37865fe915
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Include the linux/mmc/cd-gpio.h header to pickup the prototypes
for the two exported symbols.
This quiets the sparse warnings:
warning: symbol 'mmc_cd_gpio_request' was not declared. Should it be static?
warning: symbol 'mmc_cd_gpio_free' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit c79396c191 ("mmc: sdhci: prevent card detection activity
for non-removable cards") disables card detection where the cards
are marked as non-removable.
This makes sense, but the implementation detail of calling
mmc_card_is_removable() causes some problems, because
mmc_card_is_removable() is overloaded with CONFIG_MMC_UNSAFE_RESUME
semantics.
In the OLPC XO case, we need CONFIG_MMC_UNSAFE_RESUME because our root
filesystem is stored on SD, but we also have external SD card slots
where we want automatic card detection.
Refine the check to only apply to hosts marked as MMC_CAP_NONREMOVABLE,
which is defined to mean that the card is *really* nonremovable. This
could be revisited in future if we find a way to improve
CONFIG_MMC_UNSAFE_RESUME semantics.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
[stable@: please apply to 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the vm_brk() function, this is the same as "do_munmap()", except it
does the VM locking for the caller.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_have_populated_dt() is not expected to be used in drivers but
instead only in early platform init code.
Drivers on the other hand should rely on dev->of_node or of_match_device().
Besides usage of of_have_populated_dt() also throws up build error as below
which was reported by Balaji TK, when omap_hsmmc is built as a module.
ERROR: "allnodes" [drivers/mmc/host/omap_hsmmc.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
So get rid of all of_have_populated_dt() usage in omap_hsmmc driver and
instead use dev->of_node to make the same dicisions as earlier.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Benoit Cousson <b-cousson@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 46856a68dc ("mmc: omap_hsmmc: Convert hsmmc driver to use device tree")
introduced in 3.4-rc1 has a missing semi-colon, causing:
drivers/mmc/host/omap_hsmmc.c:1745: error: expected ',' or ';' before 'extern'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC v4.5 sanitize operation erases all copies of unmapped
data. However trim or erase operations must be used first
to unmap the required sectors. That was not being done.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC v4.5 discard operation is significantly different from the
existing trim operation because it is not guaranteed to work with
the new sanitize operation. Consequently mmc_can_trim() is
separated from mmc_can_discard().
Also the new discard operation does not result in the sectors being
set to all-zeros, so discard_zeroes_data must not be set.
In addition, the new discard has the same timeout as trim, but from
v4.5 trim is defined to use the hc timeout. The timeout calculation
is adjusted accordingly.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It does the same thing as "do_brk()", except it handles the VM locking
too.
It turns out that all external callers want that anyway, so we can make
do_brk() static to just mm/mmap.c while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the addition of platform specific driver data in the sdhci driver
for EXYNOS4 and EXYNOS5, the device name of sdhci controllers on EXYNOS4
and EXYNOS5 are changed accordingly.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: re-worked on top of v3.4-rc2]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When hostname contains colon (e.g. when it is an IPv6 address) it needs
to be enclosed in brackets to make parsing of NFS device string possible.
Fix nfs_do_root_mount() to enclose hostname properly when needed. NFS code
actually does not need this as it does not parse the string passed by
nfs_do_root_mount() but the device string is exposed to userspace in
/proc/mounts.
CC: Josh Boyer <jwboyer@redhat.com>
CC: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull pinctrl fixes from Linus Walleij:
- Fixed compilation errors and warnings
- Stricter checks on the ops vtable
* tag 'for-torvalds-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: implement pinctrl_check_ops
pinctrl: include <linux/bug.h> to prevent compile errors
pinctrl: fix compile error if not select PINMUX support
Pull 3 tiny tty bugfixes from Greg Kroah-Hartman.
* tag 'tty-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
drivers/tty/amiserial.c: add missing tty_unlock
pch_uart: Fix dma channel unallocated issue
ARM: clps711x: serial driver hungs are a result of call disable_irq within ISR
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB fixes for 3.4-rc4.
Most of them are in the USB gadget area, but a few other minor USB
driver and core fixes are here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
USB: serial: cp210x: Fixed usb_control_msg timeout values
USB: ehci-tegra: don't call set_irq_flags(IRQF_VALID)
USB: yurex: Fix missing URB_NO_TRANSFER_DMA_MAP flag in urb
USB: yurex: Remove allocation of coherent buffer for setup-packet buffer
drivers/usb/misc/usbtest.c: add kfrees
USB: ehci-fsl: Fix kernel crash on mpc5121e
uwb: fix error handling
uwb: fix use of del_timer_sync() in interrupt
EHCI: always clear the STS_FLR status bit
EHCI: fix criterion for resuming the root hub
USB: sierra: avoid QMI/wwan interface on MC77xx
usb: usbtest: avoid integer overflow in alloc_sglist()
usb: usbtest: avoid integer overflow in test_ctrl_queue()
USB: fix deadlock in bConfigurationValue attribute method
usb: gadget: eliminate NULL pointer dereference (bugfix)
usb: gadget: uvc: Remove non-required locking from 'uvc_queue_next_buffer' routine
usb: gadget: rndis: fix Missing req->context assignment
usb: musb: omap: fix the error check for pm_runtime_get_sync
usb: gadget: udc-core: fix asymmetric calls in remove_driver
usb: musb: omap: fix crash when musb glue (omap) gets initialized
...
Pull xen fixes from Konrad Rzeszutek Wilk:
- mechanism to work with misconfigured backends (where they are
advertised but in reality don't exist).
- two tiny compile warning fixes.
- proper error handling in gnttab_resume
- Not using VM_PFNMAP anymore to allow backends in the same domain.
* tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen/p2m: m2p_find_override: use list_for_each_entry_safe"
xen/resume: Fix compile warnings.
xen/xenbus: Add quirk to deal with misconfigured backends.
xen/blkback: Fix warning error.
xen/p2m: m2p_find_override: use list_for_each_entry_safe
xen/gntdev: do not set VM_PFNMAP
xen/grant-table: add error-handling code on failure of gnttab_resume
This reverts commit cf450136bf.
It breaks reboot on at least one Thinkpad T43, as reported by Jörg Otte:
"On reboot it shuts down as normal.
The last lines displayed are:
>Unmounting temporary filesystems.. [OK]
>Deactivating swap... [OK]
>Unmounting local filesystems... [OK]
>Will now restart
> Restarting system
Then I hear it accessing the cd-drive, but then it's being stuck."
Jörg bisected the regression to this commit.
That commit fixes another machine (see
https://bugzilla.kernel.org/show_bug.cgi?id=11533
for details) that has a BIOS bug and doesn't support ACPI reset.
However, at least one of those other reporters no longer even has the
machine in question, and had a different workaround to begin with.
Besides, it clearly was a buggy BIOS. Let's not break the correct case
to fix that case.
Reported-and-bisected-by: Jörg Otte <jrg.otte@googlemail.com>
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 24aa07882b ("memblock, x86: Replace memblock_x86_reserve/
free_range() with generic ones") replaced x86 specific memblock
operations with the generic ones; unfortunately, it lost zero length
operation handling in the process making the kernel panic if somebody
tries to reserve zero length area.
There isn't much to be gained by being cranky to zero length operations
and panicking is almost the worst response. Drop the BUG_ON() in
memblock_reserve() and update memblock_add_region/isolate_range() so
that all zero length operations are handled as noops.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: Valere Monseur <valere.monseur@ymail.com>
Bisected-by: Joseph Freeman <jfree143dev@gmail.com>
Tested-by: Joseph Freeman <jfree143dev@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43098
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pyll hwmon fixes from Guenter Roeck:
"Two patches: Fix build warning in ads1015 driver, and fix bogus power
values with current BIOSes in fam15h_power driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ads1015) Fix build warning
hwmon: fam15h_power: fix bogus values with current BIOSes
Pull sound fixes from Takashi Iwai:
"Fixes for a few regressions of HD-audio, originated partly from 3.4
and partly 3.3.
The fixes for ThinkPad docking-station are for 3.3 kernels, thus they
are based on 3.3 then merged back to 3.4, so that they can be merged
to stable tree cleanly. The non-trivial merge conflicts are because
of this action.
In addition, a couple of trivial fixes for documentation and a long-
standing issue in the listing of built-in sound driver at boot time."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/conexant - Set up the missing docking-station pins
ALSA: hda/conexant - Don't set HP pin-control bit unconditionally
ALSA: workaround: change the timing of alsa_sound_last_init()
ALSA: hda/sigmatel - Fix inverted mute LED
ALSA: hda/realtek - Fix regression on Quanta/Gericom KN1
ALSA: fix core/vmaster.c kernel-doc warning
Pull HID fixes from Jiri Kosina:
"Fix for one particular device (bluetooth Tivo Slide) and change of
'default y' -> 'default n' for CONFIG_HID_BATTERY_STRENGTH which I
overlooked in the initial merge of the battery support"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: default HID_BATTERY_STRENGTH to no
HID: tivo: fix support for bluetooth version of tivo Slide
Pull m68k arch fixes from Greg Ungerer:
"This contains four fixes for 3.4. Two fix and clean up compilation
for the nommu 68x328 CPU targets. The other two fix the platform
definition and multi-function pin setup of the second eth interface
on the ColdFire 5275 SoC."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: make sure 2nd FEC eth interface pins are enabled on 5275 ColdFire
m68knommu: fix id number for second eth device on 5275 ColdFire
m68knommu: move and fix the 68VZ328 platform bootlogo.h
m68knommu: remove the unused bootlogo.h processing for 68EZ328 and 68VZ328
When loading symbols from DSO we check multiple paths of DSO binary
until we succeed to load symbols ('.symtab' section). Once symbols are
read we try to load also plt symbols.
During the reading of plt symbols, the dso file is reopened from
location given by dso->long_name. This could be wrong in case we want
process buildid binaries.
The change is to make the plt symbols being read from the DSO path, that
normal symbols were read from.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334756818-6631-1-git-send-email-jolsa@redhat.com
[ committer note: moved dso to be the first parameter of that function ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit b960d6c43a.
If we have another thread (very likely) touched the list, we
end up hitting a problem "that the next element is wrong because
we should be able to cope with that. The problem is that the
next->next pointer would be set LIST_POISON1. " (Stefano's
comment on the patch).
Reverting for now.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
Signed-off-by: Yuri Matylitski <ym@tekinsoft.com>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This loop on EBCISR register was designed to clear IRQ sources before enabling
a DMA channel. This register is clear-on-read so a race condition can appear if
another channel is already active and has just finished its transfer.
Removing this read on EBCISR is fixing the issue as there is no case where an IRQ
could be pending: we already make sure that this register is drained at probe()
time and during resume.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Enable channel in device_issue_pending call, so that the order between
cookie assignment and channel enabling can be ensured naturally.
It fixes the mxs gpmi-nand breakage which is caused by the incorrect
order of cookie assigning and channel enabling.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <b32955@freescale.com>
Tested-by <samgandhi9@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
the cookie updates completed the cyclic dma descriptor wrongly. This caused the
BUG_ON to be hit as submit is called for completed descriptor
Fix this by not marking the cyclic descriptor as complete
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
According to the reporter, external mic starts to work if the
laptop-dmic model is used. According to BIOS pin config, all
pins are consistent with the alc269vb_laptop_dmic fixup, except
for the external mic, which is not present.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/950490
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the VIC was converted to use generic IRQ domains IRQ 0
is silently ignored. This IRQ is used on the U300 so we're
missing it now. Bump all IRQ numbers by one since they are
now decoupled from the hardware IRQ numbers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make sense to grant permission to change the status of a
regulator that is also set as always on and similarly it doesn't make
sense to allow a driver to change the voltage of a regulator which can
only be set to a single voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the recent update of the cifs_iovec_write code to use async writes,
the handling of the file position was broken. That patch added a local
"offset" variable to handle the offset, and then only updated the
original "*poffset" before exiting.
Unfortunately, it copied off the original offset from the beginning,
instead of doing so after generic_write_checks had been called. Fix
this by moving the initialization of "offset" after that in the
function.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull nfsd bugfixes from J. Bruce Fields:
"One bugfix, and one minor header fix from Jeff Layton while we're
here"
* 'for-3.4' of git://linux-nfs.org/~bfields/linux:
nfsd: include cld.h in the headers_install target
nfsd: don't fail unchecked creates of non-special files
While debugging a latency with someone on IRC (mirage335) on #linux-rt (OFTC),
we discovered that the stacktrace output of the latency tracers
(preemptirqsoff) was empty.
This bug was caused by the creation of the dynamic length stack trace
again (like commit 12b5da3 "tracing: Fix ent_size in trace output" was).
This bug is caused by the latency tracers requiring the next event
to determine the time between the current event and the next. But by
grabbing the next event, the iter->ent_size is set to the next event
instead of the current one. As the stacktrace event is the last event,
this makes the ent_size zero and causes nothing to be printed for
the stack trace. The dynamic stacktrace uses the ent_size to determine
how much of the stack can be printed. The ent_size of zero means
no stack.
The simple fix is to save the iter->ent_size before finding the next event.
Note, mirage335 asked to remain anonymous from LKML and git, so I will
not add the Reported-by and Tested-by tags, even though he did report
the issue and tested the fix.
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Also fix issue of accessing invalid msgr pointer issue. The local
msgr pointer in fucntion mpic_msgr_get will be accessed before
getting a valid address which will cause kernel crash.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In file included from arch/powerpc/sysdev/mpic_msgr.c:20:0:
~/arch/powerpc/include/asm/mpic_msgr.h: In function 'mpic_msgr_set_destination':
~/arch/powerpc/include/asm/mpic_msgr.h:117:2:
error: implicit declaration of function 'get_hard_smp_processor_id'
make[1]: *** [arch/powerpc/sysdev/mpic_msgr.o] Error 1
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit ae3a197e (Disintegrate asm/system.h for PowerPC) broke build of
assembly files when CONFIG_BOOKE_WDT is enabled as follows:
AS arch/powerpc/lib/string.o
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h: Assembler messages:
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h:19: Error: Unrecognized opcode: `extern'
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h:20: Error: Unrecognized opcode: `extern'
Since setup_32.c is the only user of the booke_wdt configuration variables, move
the declarations there.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 46d026ac ("powerpc/85xx: consolidate of_platform_bus_probe calls")
replaced platform-specific of_device_id tables with a single function
that probes the most of the busses in 85xx device trees. If a specific
platform needed additional busses probed, then it could call
of_platform_bus_probe() again. Typically, the additional platform-specific
busses are children of existing busses that have already been probed.
of_platform_bus_probe() does not handle those child busses automatically.
Unfortunately, this doesn't actually work. The second (platform-specific)
call to of_platform_bus_probe() never finds any of the busses it's asked
to find.
To remedy this, the platform-specific of_device_id tables are eliminated,
and their entries are merged into mpc85xx_common_ids[], so that all busses
are probed at once.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.
Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices. This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current
registered.
Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).
Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: svenjoac@gmx.de
Cc: torvalds@linux-foundation.org
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/1334802459.28674.209.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:
From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.
Prior to commit 'fa4da365bc7772c', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'fa4da365bc7772c', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).
But the commit 'fa4da365bc7772c' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.
Enforce the mode setting when trying to set an event.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: svenjoac@gmx.de
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181723350.2542@ionos
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.
Also we used "pri" before capping it. It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.
The modified firmware will never be released, so we're better off
merging this now rather than waiting for v3.5.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
linux/drivers/xen/manage.c: In function 'do_suspend':
linux/drivers/xen/manage.c:160:5: warning: 'si.cancelled' may be used uninitialized in this function
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull drm fixes from Dave Airlie:
"It's like a grab bag of one liners:
- core: fix page flip error path, reorder object teardown.
- usb: fix the drm_usb module license.
- i915: VT switch on SNB with non-native modes fix, and a regression
fix from 3.3.
- radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
IA64, but its a generic bug), an rn50 regression from 3.3, turn off
MSIs on rv515 (it loses rearms every so often)."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: Set special lane map for the right chipset
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
drm: Releasing FBs before releasing GEM objects during drm_release
drm/nouveau/pm: don't read/write beyond end of stack buffer
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
radeon: fix r600/agp when vram is after AGP (v3)
drm: fix page_flip error handling
drm/radeon/kms: fix the regression of DVI connector check
drm/usb: fix module license on drm/usb layer.
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
drm/radeon: disable MSI on RV515
drm/i915: don't clobber the special upscaling lvds timings
Fix the following compilation failure:
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
by adding a dependency on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 9f85550347.
Peter Zijlstra says:
| Argh, how did that ever make it upstream, please drop.
|
| Russell, please make that go away upstream.
|
| Like I said, this is both completely the wrong way to solve, and you're
| so not paying attention, see:
|
| 5fbd036b55
| 2baab4e904
| e3831edd59
|
| What's even worse:
|
| git describe --contains 9f85550347 --match "v*"
| v3.4-rc3~1^2~3
|
| that nonsense got merged long after those other commits.
Linus Walleij says:
| My bad, was because the initial patch was submitted march 9th before
| these fixes were merged:
| http://marc.info/?l=linux-arm-kernel&m=133159655513844&w=2
|
| It was pending for a while in Russell's patch tracker and I
| rebased it to -rc2 without paying enough attention to recent
| related scheduler fixes ... lesson learned.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull KVM updates from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: lock slots_lock around device assignment
KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
KVM: unmap pages from the iommu when slots are removed
KVM: PMU emulation: GLOBAL_CTRL MSR should be enabled on reset
MAX_ADDR_LEN is 32. ETH_ALEN is 6. mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array. I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we may be simulating flock() locks using NFS byte range locks,
we can't rely on the VFS having checked the file open mode for us.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
All callers of nfs4_handle_exception() that need to handle
NFS4ERR_OPENMODE correctly should set exception->inode
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.
Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.
That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.
To trigger this, put this in your guest config:
vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']
instead of this:
vnc=1
vnclisten="0.0.0.0"
CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v3: Split delay in non-essential (30 seconds) and essential
devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the L3 disable slot is already in use, return -EEXIST instead of
-EINVAL. The caller, store_cache_disable(), checks this return value to
print an appropriate warning.
Also, we want to signal with -EEXIST that the current index we're
disabling has actually been already disabled on the node:
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_0
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_0
-bash: echo: write error: File exists
$ echo 12 > /sys/devices/system/cpu/cpu3/cache/index3/cache_disable_1
-bash: echo: write error: File exists
$ echo 12 > /sys/devices/system/cpu/cpu5/cache/index3/cache_disable_1
-bash: echo: write error: File exists
The old code would say
-bash: echo: write error: Invalid argument
for disable slot 1 when playing the example above with no output in
dmesg, which is clearly misleading.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20120419070053.GB16645@elgon.mountain
[Boris: add testing for the other index too]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge fixes for Thinkpad docking-station regressions for 3.3 kernels
back to 3.4. These were committed in that branch to make the stable
merging easier.
Conflicts:
sound/pci/hda/patch_conexant.c
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.
Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.
Reported-by: Evan McNabb (Red Hat)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.
If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NUL-terminate after strncpy.
If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.
Signed-off-by: Jim Meyering <meyering@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The output of "make versioncheck" points a incorrect include of
version.h in the drivers/gpu/drm/gma500/mdfld_dsi_output.h:
drivers/gpu/drm/gma500/mdfld_dsi_output.h: 32 linux/version.h not needed.
If we take a look in the file, we can agree to remove it.
Cc: David Airlie <airlied@linux.ie>
Cc: <dri-devel@lists.freedesktop.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If AGP is placed in the middle, the size_af is off-by-one, it results
in VRAM being placed at 0x7fffffff instead of 0x8000000.
v2: fix the vram_start setup.
v3: also fix r7xx & newer ASIC
Reported-by: russiane39 on #radeon
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some output pins on Conexant chips have no HP control bit, but the
auto-parser initializes these pins unconditionally with PIN_HP.
Check the pin-capability and avoid the HP bit if not supported.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/i915: don't clobber the special upscaling lvds timings
The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.
Fixed the typo now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 4f5ca836b "HID: hid-input: add support for HID devices reporting
Battery Strength" added the CONFIG_HID_BATTERY_STRENGTH option to report
the battery strength of HID devices. The commit log explicitly mentions
it not working properly with recent userspace, but it is default y
anyway. This is rather odd, and actually causes problems on real
systems.
This works around Fedora bug
https://bugzilla.redhat.com/show_bug.cgi?id=806295
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current alsa_sound_last_init() was called as __initcall().
So, on current ALSA, only devices that had been properly
registered at this point were shown.
So, it will show "No soundcards found" if driver requests
probe deferment. it's often misleading.
This patch delays the timing of alsa_sound_last_init()
as workaround.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The problem is caused by the interaction of two features in the Linux
memory management code.
A processes address space is described by a struct mm_struct, and
every thread has a pointer to the mm it should run in. The exception
to this are kernel threads, which don't have an mm, and so borrow
the mm from the last thread which ran. The system is bootstrapped
by the initial kernel thread using init's mm (even though init hasn't
been created yet, its mm is the static init_mm).
The other feature is how the kernel handles the page table which
describes the portion of the address space which is only visible when
executing inside the kernel, and which is shared by all threads. On
the SH4 the only portion of the kernel's address space which described
using the page table is called P3, from 0xc0000000 to 0xdfffffff. This
portion of the address space is divided into three:
- mappings for dma_alloc_coherent()
- mappings for vmalloc() and ioremap()
- fixmap mappings, primarily used in copy_user_pages() to create
kernel mappings of user pages with the correct cache colour.
To optimise the TLB miss handler we don't want to add an additional
condition which checks whether the faulting address is in the user or
the kernel portion of the address space, and so all page tables have a
common portion which describes the kernel part of the address
space. As the SH4 uses a two level page table, only the kernel portion
of first level page table (the pgd entries) is duplicated. These all
point to the same second level entries (the pte's), and so no memory
is wasted.
The reference page table for the kernel is called the swapper_pg_dir,
and when a new page table is created for a new process the kernel
portion of the page table is copied from swapper_pg_dir. This works
fine when changes only occur in the second level of the kernel's page
table, or the first level entries are created before any new user
processes. However if a change occurs to the first level of the page
table, and there are existing processes which don't have this entry in
their page table, this new entry needs to be added. This is done on
demand, when the kernel accesses a P3 address which isn't mapped using
the current page table, the code in vmalloc_fault() copies the entry
from the reference page table (swapper_pg_dir) into the current
processes page table.
The bug which this patch addresses is that the code in vmalloc_fault()
was not copying addresses which fell in the dma_alloc_coherent()
portion of the address space, and it should have been copying any P3
address.
Why we hadn't seen this before, and what made this hard to reproduce,
is that normally the kernel will have called dma_alloc_coherent(), and
accessed the memory mapping created, before any user process
runs. Typically drivers such as USB or SATA will have created and used
mappings of this type during the kernel initialisation, when probing
for the attached devices, before init runs. Ethernet is slightly
different, as it normally only creates and accesses
dma_alloc_coherent() mappings when the network is brought up, but if
kernel level IP configuration is used this will also occur before any
user space process runs. So the first reproduction of this problem
which we saw was occurred when USB and SATA were removed from the
kernel, and then bring up Ethernet from user space using ifconfig.
I'd like to thank Joseph Bormolini who did the hard work reducing the
problem to this simple to reproduce criteria.
In your case the situation is slightly different, and turns out to
depends on the exact kernel configuration (which we had) and your
ramdisk contents (which we didn't - hence the need for some assumptions).
In this case the problem is a side effect of kernel level module
loading. Kernel subsystems sometimes trigger the load of kernel
modules directly, for example the crypto subsystem tries to load the
cryptomgr and MTD tries to load modules for Flash partitioning if
these are not built into the kernel. This is done by the kernel
creating a user process which runs insmod to try and load the
appropriate module.
In order for this to cause problems the system must be running with a
initrd or initramfs, which contains an insmod executable - if the
kernel can't find an insmod to run, no user process is created, and
the problem doesn't occur. If an insmod is found, a process is
created to run it, which will inherit the kernel portion of the
swapper_pg_dir first level page table. It doesn't matter whether the
inmod is successful or not, but when the the kernel scheduler context
switches back to the kernel initialisation thread, the insmod's mm is
'borrowed' by the kernel thread, as it doesn't have an address space
of its own. (Reference counting is used to ensure this mm is not
destroyed, even though the user process which caused its creation may no
longer exist.) If this address space doesn't have a first level page
table entry for the consistent mappings, and a driver tries to access
such a mapping, we are in the same situation as described above,
except this time in a kernel thread rather than a user thread
executing inside the kernel.
See bugzilla: 15425, 15836, 15862, 16106, 16793
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
My 9ce70c0240 "memcg: fix deadlock by inverting lrucare nesting" put a
nasty little bug into v3.3's version of mem_cgroup_replace_page_cache(),
sometimes used for FUSE. Replacing __mem_cgroup_commit_charge_lrucare()
by __mem_cgroup_commit_charge(), I used the "pc" pointer set up earlier:
but it's for oldpage, and needs now to be for newpage. Once oldpage was
freed, its PageCgroupUsed bit (cleared above but set again here) caused
"Bad page state" messages - and perhaps worse, being missed from newpage.
(I didn't find this by using FUSE, but in reusing the function for tmpfs.)
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [v3.3 only]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Through the transition to the auto-parser, the support for
Quanta/Gericom KN1 got broken. There are two problems behind it:
- This machine doesn't like the default COEF setup for ALC260 we take
now as default
- BIOS doesn't set the pins correctly at all; especially the machine
uses only the pin 0x0f for both headphone and speaker
This patch adds the fixup as a workaround for these issues.
Reported-and-tested-by: Uros Vampl <mobile.leecher@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is another fixes series for AT91 designed for 3.4-rc.
We experienced some issues while compiling some drivers as modules: Joachim has
corrected several of them. We may reduce this number of exported values by
reworking some drivers, in the future.
Some drivers are also modified here, I would like to keep them in the series
as the modifications are really related with our recent move to irqdomains or
simply related with compiler annotations.
I keep dmaengine Kconfig modification in this "fixes" series. The DMA
driver will not be available for 9x5 SoC family otherwise.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dmaengine: Kconfig: fix Atmel at_hdmac entry
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
USB: ohci-at91: change annotations for probe/remove functions
leds-atmel-pwm.c: Make pwmled_probe() __devinit
ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
ARM: at91: fix rm9200ek flash size
ARM: at91: remove empty at91_init_serial function
ARM: at91: fix typo in at91_pmc_base assembly declaration
ARM: at91: Export at91_matrix_base
ARM: at91: Export at91_pmc_base
ARM: at91: Export at91_ramc_base
ARM: at91: Export at91_st_base
* 'fixes-for-arm-soc-20120416' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: update defconfig
ARM: ux500: Fix unmet direct dependency
ARM: ux500: wake secondary cpu via resched
ARM i.MX misc fixes for -rc
* tag 'v3.4-rc3-imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: Fix imx5 idle logic bug
ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
Fix regression for bad uart muxing and oops when PM is not set.
Revert one softreset regression and few other minor fixes.
* tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
ARM: OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status"
ARM: OMAP2+: hwmod: add softreset delay field and OMAP4 data
ARM: OMAP1: mux: add missing include
This error appeared in the bcmring_defconfig build:
CC arch/arm/mach-bcmring/core.o
arch/arm/mach-bcmring/core.c:55: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:55: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:56: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:56: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:134: error: 'uartA_device' undeclared here (not in a function)
arch/arm/mach-bcmring/core.c:135: error: 'uartB_device' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-bcmring/core.o] Error 1
It appeared as of commit 8ede1ae65e
"ARM: amba: bcmring: use common amba device initializers"
Note that in include/linux/amba/bus.h we have:
#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) ...
There is an a --> A case error in the busid and a missing zero
placeholder for the id field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[olof: reworded patch subject]
Signed-off-by: Olof Johansson <olof@lixom.net>
As pointed out by Jason Baron, when assigning a device to a guest
we first set the iommu domain pointer, which enables mapping
and unmapping of memory slots to the iommu. This leaves a window
where this path is enabled, but we haven't synchronized the iommu
mappings to the existing memory slots. Thus a slot being removed
at that point could send us down unexpected code paths removing
non-existent pinnings and iommu mappings. Take the slots_lock
around creating the iommu domain and initial mappings as well as
around iommu teardown to avoid this race.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add missing "personality.h"
security/commoncap.c: In function 'cap_bprm_set_creds':
security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function)
security/commoncap.c:510: error: (Each undeclared identifier is reported only once
security/commoncap.c:510: error: for each function it appears in.)
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
kvm_set_shared_msr() may not be called in preemptible context,
but vmx_set_msr() does so:
BUG: using smp_processor_id() in preemptible [00000000] code: qemu-kvm/22713
caller is kvm_set_shared_msr+0x32/0xa0 [kvm]
Pid: 22713, comm: qemu-kvm Not tainted 3.4.0-rc3+ #39
Call Trace:
[<ffffffff8131fa82>] debug_smp_processor_id+0xe2/0x100
[<ffffffffa0328ae2>] kvm_set_shared_msr+0x32/0xa0 [kvm]
[<ffffffffa03a103b>] vmx_set_msr+0x28b/0x2d0 [kvm_intel]
...
Making kvm_set_shared_msr() work in preemptible is cleaner, but
it's used in the fast path. Making two variants is overkill, so
this patch just disables preemption around the call.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull fuse updates from Miklos Szeredi.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use flexible array in fuse.h
fuse: allow nanosecond granularity
fuse: O_DIRECT support for files
fuse: fix nlink after unlink
Pull s390 updates from Martin Schwidefsky:
"A couple of bug fixes, one of them is a TLB flush fix. Included as
well is one small coding style patch and a patch to update the default
configuration."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] Fix compile error in swab.h
[S390] Fix stfle() lowcore protection problem
[S390] cpum_cf: get rid of compile warnings
[S390] irq: simple coding style change
[S390] update default configuration
[S390] fix tlb flushing for page table pages
[S390] kernel: Use local_irq_save() for memcpy_real()
[S390] s390/char/vmur.c: fix memory leak
[S390] drivers/s390/block/dasd_eckd.c: add missing dasd_sfree_request
This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.
0. initial value: use_dma=0
1. starup()
- dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
- Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
- memory access violation occurs!
This patch fixes the issue.
Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following shows up in chroma_defconfig:
CC arch/powerpc/sysdev/scom.o
arch/powerpc/sysdev/scom.c: In function 'scom_debug_init':
arch/powerpc/sysdev/scom.c:182:36: error: 'powerpc_debugfs_root' undeclared (first use in this function)
arch/powerpc/sysdev/scom.c:182:36: note: each undeclared identifier is reported only once for each function it appears in
make[2]: *** [arch/powerpc/sysdev/scom.o] Error 1
make[1]: *** [arch/powerpc/sysdev/scom.o] Error 2
A bisect leads to commit 9ffc93f203
"Remove all #inclusions of asm/system.h"
Add the debug header which contains powerpc_debugfs_root.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Beregalov reported skb_over_panic errors and provided stack
trace.
I occurs commit a21d45726a (tcp: avoid order-1 allocations on wifi and
tx path) added a regression, when a retransmit is done after a partial
ACK.
tcp_retransmit_skb() tries to aggregate several frames if the first one
has enough available room to hold the following ones payload. This is
controlled by /proc/sys/net/ipv4/tcp_retrans_collapse tunable (default :
enabled)
Problem is we must make sure _pskb_trim_head() doesnt fool
skb_availroom() when pulling some bytes from skb (this pull is done when
receiver ACK part of the frame).
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull security subsystem fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
fcaps: clear the same personality flags as suid when fcaps are used
mpi: Avoid using freed pointer in mpi_lshift_limbs()
Smack: move label list initialization
Fatal errors such as a device disconnect must not trigger
error handling. The error returns must be checked.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BCJ filters were meant to be enabled already on these
archs, but the xz_wrap.sh script was buggy. Enabling the
filters should give smaller kernel images.
xz_wrap.sh will now use $SRCARCH instead of $ARCH to detect
the architecture. That way it doesn't need to care about the
subarchs (like i386 vs. x86_64) since the BCJ filters don't
care either.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Acked-by: Jan Beulich <jbeulich@suse.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull libara fixes from Jeff Garzik:
- Notable regression fix. Forbid dynamic runtime power management by
default, due to issues with suspend/resume and hotplug.
To re-enable, use sysfs.
- make ata_print_id atomic, due to ref from multiple contexts
- sata_mv warning fix
- ata_piix new PCI ID
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: forbid port runtime pm by default, fixing regression
libata: make ata_print_id atomic
sata_mv: silence an uninitialized variable warning
ata_piix: IDE-mode SATA patch for Intel DH89xxCC DeviceIDs
drivers/block/xen-blkback/xenbus.c: In function 'xen_blkbk_discard':
drivers/block/xen-blkback/xenbus.c:419:4: warning: passing argument 1 of 'dev_warn' makes pointer from integer without a cast
+[enabled by default]
include/linux/device.h:894:5: note: expected 'const struct device *' but argument is of type 'long int'
It is unclear how that mistake made it in. It surely is wrong.
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit 'c104f1fa1ecf4ee0fc06e31b1f77630b2551be81': (14566 commits)
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
kconfig: delete last traces of __enabled_ from autoconf.h
Revert "kconfig: fix __enabled_ macros definition for invisible and un-selected symbols"
kconfig: fix IS_ENABLED to not require all options to be defined
irq_domain: fix type mismatch in debugfs output format
staging: android: fix mem leaks in __persistent_ram_init()
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
staging: iio: hmc5843: Fix crash in probe function.
panic: fix stack dump print on direct call to panic()
drivers/rtc/rtc-pl031.c: enable clock on all ST variants
Revert "mm: vmscan: fix misused nr_reclaimed in shrink_mem_cgroup_zone()"
hugetlb: fix race condition in hugetlb_fault()
drivers/rtc/rtc-twl.c: use static register while reading time
drivers/rtc/rtc-s3c.c: add placeholder for driver private data
drivers/rtc/rtc-s3c.c: fix compilation error
MAINTAINERS: add PCDP console maintainer
memcg: do not open code accesses to res_counter members
drivers/rtc/rtc-efi.c: fix section mismatch warning
...
The symbol table on x86-64 starts to have entries that have names
like:
_GLOBAL__sub_I_65535_0___mod_x86cpu_device_table
They are of type STT_FUNCTION and this one had a length of 18. This
matched the device ID validation logic and it barfed because the
length did not meet the device type's criteria.
--------------------
FATAL: arch/x86/crypto/aesni-intel: sizeof(struct x86cpu_device_id)=16 is not a modulo of the size of section __mod_x86cpu_device_table=18.
Fix definition of struct x86cpu_device_id in mod_devicetable.h
--------------------
These are some kind of compiler tool internal stuff being emitted and
not something we want to inspect in modpost's device ID table
validation code.
So skip the symbol if it is not of type STT_OBJECT.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
From John:
Another batch of fixes intended for 3.4...
First up, we have a minor signedness fix for libertas from Amitkumar
Karwar. Next, Arend gives us a brcm80211 fix for correctly enabling
Tx FIFOs on channels 12 and 13. Bing Zhao gives us some register
address corrections for mwifiex. Felix give us a trio of fixes --
one for ath9k to wake the hardware properly from full sleep, one for
mac80211 to properly handle packets in cooked monitor mode, and one
for ensuring that the proper HT mode selection is honored.
Hauke gives us a bcma fix for handling the lack of an sprom. Jonathon
Bither gives us an ath5k fix for a missing THIS_MODULE build issue,
and another ath5k fix for an io mapping leak. Lukasz Kucharczyk
fixes a bitwise check in cfg80211, and Sujith gives us an ath9k fix
for assigning sequence numbers for fragmented frames. Finally, we
have a MAINTAINERS change from Wey-Yi Guy -- congrats to Johannes
Berg for taking the lead on iwlwifi. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Forbid port runtime pm by default because it has known hotplug issue.
User can allow it by, for example
echo auto > /sys/devices/pci0000:00/0000:00:1f.2/ata2/power/control
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following build warning is seen in some configurations.
drivers/hwmon/ads1015.c: In function 'show_in':
drivers/hwmon/ads1015.c:129: warning: 'in' may be used uninitialized in this function
Fix by separating the register read function from the code converting the result
into mV.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Newer BKDG[1] versions recommend a different initialization value for
the running average range register in the northbridge. This improves
the power reading by avoiding counter saturations resulting in bogus
values for anything below about 80% of TDP power consumption.
Updated BIOSes will have this new value set up from the beginning,
but meanwhile we correct this value ourselves.
This needs to be done on all northbridges, even on those where the
driver itself does not register at.
This fixes the driver on all current machines to provide proper
values for idle load.
[1]
http://support.amd.com/us/Processor_TechDocs/42301_15h_Mod_00h-0Fh_BKDG.pdf
Chapter 3.8: D18F5xE0 Processor TDP Running Average (p. 452)
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
[guenter.roeck@ericsson.com: Removed unnecessary return statement]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
The bitfield member mount_opt was too small by one bit to hold the mount
option that enabled to include data extents in the integrity checker.
Since the same issue happened when the BTRFS_MOUNT_PANIC_ON_FATAL_ERROR
option was added (git rebase silently merges so that the increase of the
size of the bitfield member is lost), the bit limit was removed entirely.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
When a filesystem is mounted with the degraded option, it is
possible that some of the devices are not there.
btrfs_ioctl_dev_info() crashs in this case because the device
name is a NULL pointer. This ioctl was only used for scrub.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
It is basically a good thing if we are interruptible when waiting for
free space, but the generality in which it is implemented currently
leads to system calls being interruptible that are not documented this
way. For example git can't handle interrupted unlink(), leading to
corrupt repos under space pressure.
Instead we raise the bar to only be interruptible by SIGKILL.
Thanks to David Sterba for suggesting this.
Signed-off-by: Arne Jansen <sensille@gmx.net>
The caller expects this function to return with the lock held and
releases it immediately on error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
A user reported a panic where we were trying to fix a bad mirror but the
mirror number we were giving was 0, which is invalid. This is because we
don't do the transid verification until after the read, so as far as the
read code is concerned the read was a success. So instead store the mirror
we read from so that if there is some failure post read we know which mirror
to try next and which mirror needs to be fixed if we find a good copy of the
block. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Fix a bug, where in case we need to adjust stripe_size so that the
length of the resulting chunk is less than or equal to max_chunk_size,
DUP chunks turn out to be only half as big as they could be.
Cc: Arne Jansen <sensille@gmx.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
iref_to_path and iterate_irefs both increment the eb's refcount to use it
after releasing the path. Both depend on consistent data remaining in the
extent buffer and need a read lock to protect it.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Avoid calling free_extent_buffer more than once when the iterator function
returns non-zero. The only code that uses this is scrub repair for corrupted
nodatasum blocks.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Make free_ipath() behave like most other freeing functions in the
kernel and gracefully do nothing when passed a NULL pointer.
Besides this making the bahaviour consistent with functions such as
kfree(), vfree(), btrfs_free_path() etc etc, it also fixes a real NULL
deref issue in fs/btrfs/ioctl.c::btrfs_ioctl_ino_to_path(). In that
function we have this code:
...
ipath = init_ipath(size, root, path);
if (IS_ERR(ipath)) {
ret = PTR_ERR(ipath);
ipath = NULL;
goto out;
}
...
out:
btrfs_free_path(path);
free_ipath(ipath);
...
If we ever take the true branch of that 'if' statement we'll end up
passing a NULL pointer to free_ipath() which will subsequently
dereference it and we'll go "Boom" :-(
This patch will avoid that.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
clear_extent_bit()
{
next_node = rb_next(&state->rb_node);
...
clear_state_bit(state); <-- this may free next_node
if (next_node) {
state = rb_entry(next_node);
...
}
}
clear_state_bit() calls merge_state() which may free the next node
of the passing extent_state, so clear_extent_bit() may end up
referencing freed memory.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Currently it returns a set of bits that were cleared, but this return
value is not used at all.
Moreover it doesn't seem to be useful, because we may clear the bits
of a few extent_states, but only the cleared bits of last one is
returned.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Our code is not ready to cope with a sectorsize that's not equal to PAGE_SIZE.
It will lead to hanging-on while writing something.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
This reverts commit 6fe0d06282.
Paul bisected this regression.
The conversion was done blindly and is wrong, as it does not provide a
primary handler to disable the level type irq on the device level.
Neither does it set the IRQF_ONESHOT flag which handles that at the irq
line level. This can't be done as the interrupt might be shared, though
we might extend the core to force it.
So an interrupt on this line will wake up the thread, but immediately
unmask the irq after that. Due to the interrupt being level type the
hardware interrupt is raised over and over and prevents the irq thread
from handling it. Fail.
request_irq() unfortunately does not refuse such a request and the patch
was obviously never tested with real interrupts.
Bisected-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally when there are 2 copies of a block, we add both to the
reada extent tree and prefetch only the one that is easier to reach.
This way we can better utilize multiple devices.
In case of DUP this makes no sense as both copies reside on the
same device.
Signed-off-by: Arne Jansen <sensille@gmx.net>
When inserting into the radix tree returns EEXIST, get the existing
entry without giving up the spinlock in between.
There was a race for both the zones trees and the extent tree.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Follow those instructions, and you'll trigger a warning in the
beginning of d_set_d_op():
# mkfs.btrfs /dev/loop3
# mount /dev/loop3 /mnt
# btrfs sub create /mnt/sub
# btrfs sub snap /mnt /mnt/snap
# touch /mnt/snap/sub
touch: cannot touch `tmp': Permission denied
__d_alloc() set d_op to sb->s_d_op (btrfs_dentry_operations), and
then simple_lookup() reset it to simple_dentry_operations, which
triggered the warning.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Current APIC code assumes MSR_IA32_APICBASE is present for all systems.
Pentium Classic P5 and friends didn't have this MSR. MSR_IA32_APICBASE
was introduced as an architectural MSR by Intel @ P6.
Code paths that can touch this MSR invalidly are when vendor == Intel &&
cpu-family == 5 and APIC bit is set in CPUID - or when you simply pass
lapic on the kernel command line, on a P5.
The below patch stops Linux incorrectly interfering with the
MSR_IA32_APICBASE for P5 class machines. Other code paths exist that
touch the MSR - however those paths are not currently reachable for a
conformant P5.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linux.intel.com>
Link: http://lkml.kernel.org/r/4F8EEDD3.1080404@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
PipeFS superblock creation routine relays on SUNRPC pernet data presense, which
is created on register_pernet_subsys() call in SUNRPC module init function.
Registering of PipeFS filesystem prior to registering of per-net subsystem
leads to races (mount of PipeFS can dereference uninitialized data).
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Setting the correct mode is required by rc-core or scancodes won't be
generated (which isn't very user-friendly).
This one-line fix should be suitable for 3.4-rc2.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If sanity check fails in scu_command(), goto error leads to unlock of
an unheld mutex. The check should not fail in reality, but it nevertheless
worth fixing.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some softwares (Kaffeine and likely xine) that uses a
DVBv5 call to switch to DVB-S2, but expects that a DVBv3 call to
switch back to DVB-S. Well, this is not right, as a DVBv3 call
doesn't know anything about delivery systems.
However, as, by accident, this used to work, we need to restore its
behavior, in order to avoid regressions with those softwares.
Reported on this Fedora 16 bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=812895
Reported-by: Dieter Roever <Dieter.Roever@gmx.de>
Cc: stable@kernel.org # for version 3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.
commit fa4da365b(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit 77b0d60c5(
clockevents: Leave the broadcast device in shutdown mode when not
needed).
The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.
commit fa4da365b tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.
The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users.
That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos
usb_nop_xceiv_unregister is needed on failure of usb_get_transceiver, as
done in other error-handling code in the same function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Looks like we cannot live without that double_buffer_not_ok
flag due to many HW bugs this MUSB core has.
So, let's drop the __deprecated flag to avoid annoying
compile warnings.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The imx5_idle() check of the tzic_eanble_wake() return value uses
incorrect (inverted) logic causing all attempt to idle to fail.
Signed-off-by: Robert Lee <rob.lee@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 6b783f7c (irq_domain: Remove irq_domain_add_simple()
replaced irq_domain_add_simple with irq_domain_add_legacy()
Implement this conversion so that imx27-dt can be built again.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for CONFIG_REGULATOR_FIXED_VOLTAGE.
Without this option the mx27_3ds cannot have the external Ethernet functional
due to the need of smsc regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not only do the pageflip work without it at non-native modes (i.e. with
the panel fitter enabled), it also causes normal (non-pageflipped)
modesets to fail.
Reported-by: Adam Jackson <ajax@redhat.com>
Tested-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Wanted-by-for-fixes: Dave Airlie <airlied@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Leading up to the ->device_prep_slave_sg change in
185ecb5f4f 'dmaengine: add context
parameter to prep_slave_sg and prep_dma_cyclic' a generic wrapper was
added in place to guard against the API change, though the fsi driver
wasn't updated in the process (presumably its dmaengine support hadn't
been merged yet at the time). This trivially switches over to the new
wrapper and gets it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix kernel-doc warning in sound/core/vmaster.c:
Warning(sound/core/vmaster.c:429): No description found for parameter 'private_data'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a process increases permissions using fcaps all of the dangerous
personality flags which are cleared for suid apps should also be cleared.
Thus programs given priviledge with fcaps will continue to have address space
randomization enabled even if the parent tried to disable it to make it
easier to attack.
Signed-off-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Fix kernel-doc warning in net/sock.h:
Warning(include/net/sock.h:377): No description found for parameter 'sk_peek_off'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free card->mem in the error-handling code since it was successfully
allocated just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionally, this change is a NOP.
Semantically, rt6_clean_expires() wants to do rt->dst.from = NULL instead of
rt->dst.expires = 0. It is clearing the RTF_EXPIRES flag, so the union is going
to be treated as a pointer (dst.from) not a long (dst.expires).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1716a961 (ipv6: fix problem with expired dst cache) broke PMTU
discovery. rt6_update_expires() calls dst_set_expires(), which only updates
dst->expires if it has not been set previously (expires == 0) or if the new
expires is earlier than the current dst->expires.
rt6_update_expires() needs to zero rt->dst.expires, otherwise it will contain
ivalid data left over from rt->dst.from and will confuse dst_set_expires().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
arcrimi_probe() calls BUGMSG() before register_netdev() happens. BUGMSG()
itself prints dev->name, but as the format string hasn't been expanded by
register_netdev() yet, the output contains bogus device name such as
arc%d: Given: node 00h, shmem 0h, irq 0
As we don't know the device name yet, just drop the prefix completely from
the debugging messages.
Reported-by: Steven Young <sdyoung@vt220.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the start of the function we assign 'a->d' to 'ap'. Then we use the
RESIZE_IF_NEEDED macro on 'a' - this may free 'a->d' and replace it
with newly allocaetd storage. In that case, we'll be operating on
freed memory further down in the function when we index into 'ap[]'.
Since we don't actually need 'ap' until after the use of the
RESIZE_IF_NEEDED macro we can just delay the assignment to it until
after we've potentially resized, thus avoiding the issue.
While I was there anyway I also changed the integer variable 'n' to be
const. It might as well be since we only assign to it once and use it
as a constant, and then the compiler will tell us if we ever assign to
it in the future.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
A kernel with Smack enabled will fail if tmpfs has xattr support.
Move the initialization of predefined Smack label
list entries to the LSM initialization from the
smackfs setup. This became an issue when tmpfs
acquired xattr support, but was never correct.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e8620 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DMTIMER source selection on OMAP1 is broken. omap1_dm_timer_set_src()
tries to use __raw_{read,write}l() to read from and write to physical
addresses, but those functions take virtual addresses.
sparse caught this:
arch/arm/mach-omap1/timer.c:50:13: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:50:13: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:50:13: got unsigned int
arch/arm/mach-omap1/timer.c:52:9: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:52:9: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:52:9: got unsigned int
Fix by using omap_{read,writel}(), just like the other users of the
MOD_CONF_CTRL_1 register in the OMAP1 codebase. Of course, in the long term,
removing omap_{read,write}l() is the appropriate thing to do; but
this will take some work to do this cleanly.
Looks like this was caused by 97933d6 (ARM: OMAP1: dmtimer: conversion
to platform devices) that dangerously moved code and changed it in
the same patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: stable@vger.kernel.org
[tony@atomide.com: updated comments to include the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ext4 regression fixes from Ted Ts'o:
"This fixes a scalability problem reported by Andi Kleen and Tim Chen;
they were quite secretive about the precise nature of their workload,
but they later admitted that it only showed up when they were using a
large sparse file, so the amount of data I/O that was needed was close
to zero.
I'm not sure how realistic this is and it's only a regression if you
consider changes made since 2.6.39 to be a "regression" vis-a-vis the
policy regarding post-merge window bug fixes, but Linus agreed it was
worth fixing, so I'm including it in this pull request.
This also fixes the journalled quota mount options, which I
accidentally broke while I was cleaning up the mount option handling."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix handling of journalled quota options
ext4: address scalability issue by removing extent cache statistics
Pull vfs fixes from Al Viro:
"A bunch of endianness fixes and a couple of nfsd error value fixes.
Speaking of endianness stuff, I'm rather tempted to slap
ccflags-y += -D__CHECK_ENDIAN__
in fs/Makefile, if not making it default for the entire tree; nfsd
regressions I've caught make one hell of a pile and we'd obviously
benefit from having that kind of stuff caught earlier..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
lockd: fix the endianness bug
ocfs2: ->e_leaf_clusters endianness breakage
ocfs2: ->rl_count endianness breakage
ocfs: ->rl_used breakage on big-endian
ocfs2: ->l_next_free_req breakage on big-endian
btrfs: btrfs_root_readonly() broken on big-endian
ext4: fix endianness breakage in ext4_split_extent_at()
nfsd: fix compose_entry_fh() failure exits
nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
nfsd: fix endianness breakage in TEST_STATEID handling
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
nfsd: fix b0rken error value for setattr on read-only mount
Currently we increment the number of RTD's per card during the DAI link
bind. This can cause an incorrect RTD count when we cannot find a component
and defer the probe (and hence perform the DAI link bind for the card again).
Fix the count so that it is cleared before every card registration
and bind attempt.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.
HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Russ Dill <russ.dill@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use list_for_each_entry_safe and remove the spin_lock acquisition in
m2p_find_override.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since we are using the m2p_override we do have struct pages
corresponding to the user vma mmap'ed by gntdev.
Removing the VM_PFNMAP flag makes get_user_pages work on that vma.
An example test case would be using a Xen userspace block backend
(QDISK) on a file on NFS using O_DIRECT.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
_omap3_sram_configure_core_dpll is called when SDRC is reprogrammed,
which is done regardless of CONFIG_PM setting, so we always need it's
setup code too. Without this, we hit a BUG() on OMAP3 when kernel is
built without CONFIG_PM:
Reprogramming SDRC clock to 332000000 Hz
------------[ cut here ]------------
kernel BUG at arch/arm/plat-omap/sram.c:342!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c001c694>] (omap3_configure_core_dpll+0x68/0x6c) from [<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x1)
[<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x138/0x1b0) from [<c001a478>] (omap2_clk_set_rate+0x14/0x2)
[<c001a478>] (omap2_clk_set_rate+0x14/0x20) from [<c001c9dc>] (clk_set_rate+0x54/0x74)
[<c001c9dc>] (clk_set_rate+0x54/0x74) from [<c022b9c8>] (omap_sdrc_init+0x70/0x90)
[<c022b9c8>] (omap_sdrc_init+0x70/0x90) from [<c022f178>] (omap3pandora_init+0x11c/0x164)
[<c022f178>] (omap3pandora_init+0x11c/0x164) from [<c022849c>] (customize_machine+0x20/0x28)
[<c022849c>] (customize_machine+0x20/0x28) from [<c0225810>] (do_one_initcall+0xa0/0x16c)
[<c0225810>] (do_one_initcall+0xa0/0x16c) from [<c02259e0>] (kernel_init+0x104/0x1ac)
[<c02259e0>] (kernel_init+0x104/0x1ac) from [<c0009cec>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Fix number parsing in cifs_parse_mount_options
Cleanup handling of NULL value passed for a mount option
As of:
29494be71a ("rcu,cleanup: simplify the code when cpu is dying")
RCU adopts callbacks from the dying CPU in its CPU_DYING notifier,
which means that any callbacks posted by later CPU_DYING notifiers
are ignored until the CPU comes back online.
A WARN_ON_ONCE() was added to __call_rcu() by:
e560140008 ("rcu: Simplify offline processing")
to check for this condition. Although this condition did not trigger
(at least as far as I know) during -next testing, it did recently
trigger in mainline:
https://lkml.org/lkml/2012/4/2/34
What is needed longer term is for RCU's CPU_DEAD notifier to adopt any
callbacks that were posted by CPU_DYING notifiers, however, the Linux
kernel has been running with this sort of thing happening for quite
some time. So the only thing that qualifies as a regression is the
WARN_ON_ONCE(), which this commit removes.
Making RCU's CPU_DEAD notifier adopt callbacks posted by CPU_DYING
notifiers is a topic for the 3.5 release of the Linux kernel.
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will
allow to select this driver for newer chips. Keep dependency on AT91 because of
the use of an header file located in include/mach directory.
Modify the comment to reflect this.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Now that we are using irqdomains, we need to convert GPIO pins to Linux
IRQ numbers using the gpio_to_irq() function.
This call is added to request/free_irq calls.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Add missing DMI_NONE entry to end of the quirks list so
dmi_check_system() won't read past the end of the list.
Signed-off-by: Martin Nyhus <martin.nyhus@gmx.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We can't control order here, and getting it inverted is harmless. So
turn this down to dev_info() and leave a note about how to fix it in
case userspace is insufficiently automagic.
Bugzilla: https://bugzilla.redhat.com/794953
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The CONFIG_FEC2 define was removed from the kernel many versions ago.
But it is still being used to set the multi-function pins when compiling
for a ColdFire 527[45] SoC that has 2 ethernet interfaces. Remove the
last remaining uses of this define, and so fix the setting of the pins
for the 2nd ethernet interface.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The second ColdFire FEC ethernet device should have an id number of 1,
not 0. Otherwise it clashes with the first FEC ethernet device.
On booting a kernel on a 5275 based board you will get messages out of
the kernel like this:
<4>------------[ cut here ]------------
<4>WARNING: at fs/sysfs/dir.c:508 0x0a8b50()
<4>sysfs: cannot create duplicate filename 'fec.0'
And likely you won't be able to completely boot up after this at all.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Jump to the label ini_nomem as done on the failure of the page allocations
above.
The code at ini_nomem is modified to accommodate different return values.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc75xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Omap3 with EVB-LAN7500-LC.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \
DPs 3 default 2 grio
tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS
tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull virtio fixes from Michael S. Tsirkin:
"Here are some virtio fixes for 3.4: a test build fix, a patch by Ren
fixing naming for systems with a massive number of virtio blk devices,
and balloon fixes for powerpc by David Gibson.
There was some discussion about Ren's patch for virtio disc naming:
some people wanted to move the legacy name mangling function to the
block core. But there's no concensus on that yet, and we can always
deduplicate later. Added comments in the hope that this will stop
people from copying this legacy naming scheme into future drivers."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix handling of PAGE_SIZE != 4k
virtio_balloon: Fix endian bug
virtio_blk: helper function to format disk names
tools/virtio: fix up vhost/test module build
Some shortcomings introduced into pci_restore_state() by commit
26f41062f2 ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit ebfc5b802f ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.
That is not entirely correct, because Type 1 and Type 2 headers have
different layouts. In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).
For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers. This effectively makes it behave
as before commit 26f41062f2 for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm dropping off as Documentation/ maintainer.
Rob Landley has agreed to take it over. Thanks, Rob.
I'll still be around reviewing patches and testing.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michel Lespinasse cleaned up the futex calling conventions in commit
37a9d912b2 ("futex: Sanitize cmpxchg_futex_value_locked API").
But the ia64 implementation was subtly broken. Gcc does not know that
register "r8" will be updated by the fault handler if the cmpxchg
instruction takes an exception. So it feels safe in letting the
initialization of r8 slide to after the cmpxchg. Result: we always
return 0 whether the user address faulted or not.
Fix by moving the initialization of r8 into the __asm__ code so gcc
won't move it.
Reported-by: <emeric.maschino@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42757
Tested-by: <emeric.maschino@gmail.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Starting from 7e16838d "i387: support lazy restore of FPU state"
we assume that fpu_owner_task doesn't need restore_fpu_checking()
on the context switch, its FPU state should match what we already
have in the FPU on this CPU.
However, debugger can change the tracee's FPU state, in this case
we should reset fpu.last_cpu to ensure fpu_lazy_restore() can't
return true.
Change init_fpu() to do this, it is called by user_regset->set()
methods.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20120416204815.GB24884@redhat.com
Cc: <stable@vger.kernel.org> v3.3
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit 26092bf5 broke handling of journalled quota mount options by
trying to parse argument of every mount option as a number. Fix this
by dealing with the quota options before we call match_int().
Thanks to Jan Kara for discovering this regression.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Revert the --strict test for the old preferred block
comment style in drivers/net and net/
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The change to make tracing_on affect only the ftrace ring buffer, caused
a bug where it wont affect any ring buffer. The problem was that the buffer
of the trace_array was passed to the write function and not the trace array
itself.
The trace_array can change the buffer when running a latency tracer. If this
happens, then the buffer being disabled may not be the buffer currently used
by ftrace. This will cause the tracing_on file to become useless.
The simple fix is to pass the trace_array to the write function instead of
the buffer. Then the actual buffer may be changed.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If either call to pcan_usb_pro_send_req() in
drivers/net/can/usb/peak_usb/pcan_usb_pro.c::pcan_usb_pro_init()
fails, we'll leak the memory we allocated to 'usb_if' with kzalloc()
when the 'usb_if' variable goes out of scope without having been
assigned to anything as we 'return err;'.
Fix this by adding appropriate kfree(usb_if) calls to the error paths.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The combination of commit 1b1247dd75
"mfd: Add support for RICOH PMIC RC5T583"
and commit 6ffc327021
"regulator: Add support for RICOH PMIC RC5T583 regulator"
are causing the i386 allmodconfig builds to fail with this:
ERROR: "rc5t583_update" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_set_bits" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_clear_bits" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_read" [drivers/regulator/rc5t583-regulator.ko] undefined!
and this:
ERROR: "rc5t583_ext_power_req_config" [drivers/regulator/rc5t583-regulator.ko] undefined!
For the 1st four, make the simple ops static inline, instead of
polluting the namespace with trivial exports. For the last one,
add an EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cld.h file contains the definition of the upcall format to talk
with nfsdcld. When I added the file though, I neglected to add it
to the headers-y target, so make headers_install wasn't installing it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's only called from amd.c:srat_detect_node(). The introduced
condition for calling the fixup code is true for all AMD
multi-node processors, e.g. Magny-Cours and Interlagos. There we
have 2 NUMA nodes on one socket. Thus there are cores having
different numa-node-id but with equal phys_proc_id.
There is no point to print error messages in such a situation.
The confusing/misleading error message was introduced with
commit 64be4c1c24 ("x86: Add
x86_init platform override to fix up NUMA core numbering").
Remove the default fixup function (especially the error message)
and replace it by a NULL pointer check, move the
Numascale-specific condition for calling the fixup into the
fixup-function itself and slightly adapt the comment.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Cc: <sp@numascale.com>
Cc: <bp@amd64.org>
Cc: <daniel@numascale-asia.com>
Link: http://lkml.kernel.org/r/20120402160648.GR27684@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The method used to work out whether we were booted by EFI firmware or
via a boot loader is broken. Because efi_main() is always executed
when booting from a boot loader we will dereference invalid pointers
either on the stack (CONFIG_X86_32) or contained in %rdx
(CONFIG_X86_64) when searching for an EFI System Table signature.
Instead of dereferencing these invalid system table pointers, add a
new entry point that is only used when booting from EFI firmware, when
we know the pointer arguments will be valid. With this change legacy
boot loaders will no longer execute efi_main(), but will instead skip
EFI stub initialisation completely.
[ hpa: Marking this for urgent/stable since it is a regression when
the option is enabled; without the option the patch has no effect ]
Signed-off-by: Matt Fleming <matt.hfleming@intel.com>
Link: http://lkml.kernel.org/r/1334584744.26997.14.camel@mfleming-mobl1.ger.corp.intel.com
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> v3.3
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assumption that irq numbers of asic3 gpios start at
IRQ_BOARD_START is certainly wrong - driver may as well
use any other base for its irqs (consider for example
the imaginary case of two ASIC3 chips onboard)
Furthermore, some platforms even don't have IRQ_BOARD_START
defined, so driver will fail to build on them:
-------------------------------------------------------
drivers/mfd/asic3.c: In function 'asic3_gpio_to_irq':
drivers/mfd/asic3.c:530: error: 'IRQ_BOARD_START' undeclared (first use in this function)
drivers/mfd/asic3.c:530: error: (Each undeclared identifier is reported only once
drivers/mfd/asic3.c:530: error: for each function it appears in.)
-------------------------------------------------------
Fix it by using irq_base from driver data.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Andi Kleen and Tim Chen have reported that under certain circumstances
the extent cache statistics are causing scalability problems due to
cache line bounces.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ux500 default config enables the db5500 and the db8500.
The incoming cpuidle driver uses the 'prcmu_enable_wakeups'
and the 'prcmu_set_power_state' functions but these ones
are defined but not implemented for the db5500, leading to
an unresolved symbol error at link time. In order to compile,
we have to disable the db5500 support which is not acceptable
for the default config.
I noticed there are also some other functions which are
defined but not implemented.
This patch fix this by removing the functions definitions
and move out of the config section the empty functions which
are normally used when the DB550 config is disabled.
Only the functions which are not implemented are concerned
by this modification.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While testing https://lkml.org/lkml/2012/4/10/123 I hit this crash:
(gdb) bt
0 0x000000000042000f in __cmd_report (rep=0x7fff80cec580) at builtin-report.c:380
1 cmd_report (argc=0, argv=<optimized out>, prefix=<optimized out>) at builtin-report.c:759
2 0x0000000000414513 in run_builtin (p=0x7724a8, argc=3, argv=0x7fff80ceca70) at perf.c:273
3 0x0000000000413d41 in handle_internal_command (argv=0x7fff80ceca70, argc=3) at perf.c:345
4 run_argv (argv=0x7fff80cec880, argcp=0x7fff80cec88c) at perf.c:389
5 main (argc=3, argv=0x7fff80ceca70) at perf.c:487
kernel_map can be NULL, so need to handle it while dumping a warning
to user.
v2:
- fixed RB_EMPTY_ROOT check -- desc takes the altnerative output when RB_EMPTY_ROOT is false.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Link: http://lkml.kernel.org/r/1334544855-55021-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Forget to unreserve after pinning. This can lead to problems in
soft reset and resume.
v2: rework patch as per Michel's suggestion.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My rv515 card is very flaky with msi enabled. Every so often it loses a rearm
and never comes back, manually banging the rearm brings it back.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a key is non persistent then it should not be used in future
connections but it should be kept for current connection. And it
should be removed when connecion is removed.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch changes the return type of function hci_persistent_key
from int to bool because it makes more sense to return information
whether a key is persistent or not as a bool.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The real function is long gone and the empty one will generate warnings
when configured without Atmel serial:
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: 'struct at91_uart_config' declared inside parameter list
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91_matrix_* macro's are used by at91_udc usb gadget driver,
which can be built as module, therefore we need to export the
variable containing matrix base address.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit b55149529d (ARM: at91/PMC: make register base soc independent)
building atmel_usba_udc as a module fails with following message
ERROR: "at91_pmc_base" [drivers/usb/gadget/atmel_usba_udc.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit f363c40 (ARM: at91: make sdram/ddr register base soc independent)
building at91_cf as a module fails with:
ERROR: "at91_ramc_base" [drivers/pcmcia/at91_cf.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export at91_ramc_base symbol to allow drivers using at91_ramc_*
functions to be built as modules again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: modify slightly commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit 5e9cf5e (ARM: at91: make ST (System Timer) soc independent)
building at91rm9200_wdt as a module fails with following message
ERROR: "at91_st_base" [drivers/watchdog/at91rm9200_wdt.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow wdt driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: use EXPORT_SYMBOL_GPL()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This regression has been introduced in
commit ca9bfa7eed
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some new drivers and changed Kconfig dependencies for the v3.4
kernel affecting the U8500 defconfig:
- The SOC config options are now brought in by default
- No need to explicitly select misc devices anymore
- I2C is selected by default
- We now have support for charging from the AB8500 so compile
in this
- The regulator framework needs to be explictly selected
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A recent change to a Kconfig configuration saw MACH_U8500
remove TPS6105X selection. In doing so Kconfig stopped
selecting REGULATORS, which is still required. This patch
sees UX500_SOC_DB8500 explicitly select it instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 68EZ328/bootlogo.h is not actually used in the 68EZ328 platform code
at all. It is used by the 68VZ328 platform code though, so move it to be
with the rest of the 68VZ328 platform code.
Commit c0e0c89c08 ("fix broken boot logo
inclusion") modified the bootlogo code to not be included in asm code.
Modify 68VZ328/bootlogo.h so that the bootlogo bit map is named correctly
for direct use in the C code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 68EZ328 and 68VZ328 platforms currently try to process their bootlogo.h
to make it clean to include in asm files. This is no longer used, the
bootlogo.h file is now included only in C code, so remove all the processing
code in the 68EZ328 and 68VZ328 Makefiles.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit 92ae03f2ef ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 26f41062f2 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by David Gibson, current code handles PAGE_SIZE != 4k
completely wrong which can lead to guest memory corruption errors:
- page_to_balloon_pfn is wrong: e.g. on system with 64K page size
it gives the same pfn value for 16 different pages.
- we also need to convert back to linux pfns when we free.
- for each linux page we need to tell host about multiple balloon
pages, but code only adds one pfn to the array.
This patch fixes all that, tested with a 64k ppc64 kernel.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although virtio config space fields are usually in guest-native endian,
the spec for the virtio balloon device explicitly states that both fields
in its config space are little-endian.
However, the current virtio_balloon driver does not have a suitable endian
swap for the 'num_pages' field, although it does have one for the 'actual'
field. This patch corrects the bug, adding sparse annotation while we're
at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
. Properly handle ~/.debug, the build id cache, when it is a symlink,
fix from Chanho Park
. Fixes for the parser generation process, from Jiri Olsa and Namhyung Kim
. Fix build when NO_GTK2 is specified, From Stephane Eranian
. When a machine is not found, bump the relevant error stat but return
0, so that we correctly move to the next perf event. Fix from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a '$PERF_BUILDID_DIR'(typically $HOME/.debug) is a symbolic link
directory, cutting of the path will fail.
Here is an example where a buildid directory is a symbolic link.
/ # ls -al /root
lrwxrwxrwx 1 root root 13 Mar 26 2012 /root -> opt/home/root
/ # cd ~
/opt/home/root # perf record -a -g sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.322 MB perf.data (~14057 samples) ]
/opt/home/root # perf archive
tar: Removing leading `/' from member names
Now please run:
$ tar xvf perf.data.tar.bz2 -C ~/.debug
wherever you need to run 'perf report' on.
/opt/home/root # mkdir temp
/opt/home/root # tar xf perf.data.tar.bz2 -C ./temp
/opt/home/root # find ./temp -name "*kernel*"
./temp/opt/home/root/.debug/[kernel.kallsyms]
-> If successfully cut off the path, [kernel.kallsyms] is located
in top of the archived file.
This patch enables to cut correctly even if the buildid directory
is a symbolic link.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333348109-12598-1-git-send-email-chanho61.park@samsung.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit 81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull from Borislav Petkov a two-patch fix from Andreas taking care of a sysfs
warning when the microcode driver is loaded on unsupported platforms.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are times we turn of the laser before shutdown. This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices. After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices. The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset. With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
Pull fbdev fixes from Florian Tobias Schandinat:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
"The fix for kyrofb is a bit large but it's just replacing "unsigned
long" by "u32" for 64 bit compatibility."
* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
fbdev: fix au1*fb builds
kyrofb: fix on x86_64
Pull the minimal btrfs branch from Chris Mason:
"We have a use-after-free in there, along with errors when mount -o
discard is enabled, and a BUG_ON(we should compile with UP more
often)."
* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use commit root when loading free space cache
Btrfs: fix use-after-free in __btrfs_end_transaction
Btrfs: check return value of bio_alloc() properly
Btrfs: remove lock assert from get_restripe_target()
Btrfs: fix eof while discarding extents
Btrfs: fix uninit variable in repair_eb_io_failure
Revert "Btrfs: increase the global block reserve estimates"
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Today's -next fails to link for me:
kernel/built-in.o:(.data+0x178e50): undefined reference to `perf_ftrace_event_register'
It looks like multiple fixes have been merged for the issue fixed by
commit fa73dc9 (tracing: Fix build breakage without CONFIG_PERF_EVENTS)
though I can't identify the other changes that have gone in at the
minute, it's possible that the changes which caused the breakage fixed
by the previous commit got dropped but the fix made it in.
Link: http://lkml.kernel.org/r/1334307179-21255-1-git-send-email-broonie@opensource.wolfsonmicro.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few OMAP hwmod fixes against v3.4-rc2. One of them is a reversion
of a previous v3.4-rc patch that caused some regressions, and upon
further review, appears not to be necessary. The other two are fairly
minor.
Pull sparc fixes from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
Pull GPIO bug fixes from Grant Likely:
"Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warning in gpio-samsung.c file
gpio: Fix range check in of_gpio_simple_xlate()
gpio: Fix uninitialized variable bit in adp5588_irq_handler
gpio/sodaville: Convert sodaville driver to new irqdomain API
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratch register addresses have been changed for newer chips.
Since the old chip was never shipped and it will not be supported
any more, just update register addresses to support the new chips.
Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cross compiling ath5k for a Mips machine with kernel 3.2.14
the compilation fails with "/ath5k/ahb.c:231:12: error: 'THIS_MODULE' undeclared here (not in a function)"
Fix the build by including <linux/export.h>
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to
mac80211.
This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.
Cc: stable@vger.kernel.org
Tested-by: Francesco Saverio Schiavarelli <fschiava@libero.it>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return type for lbs_auth_to_authtype() is changed from "u8" to
"int" to return negative error code correctly.
Also an error check is added in connect handler for invalid auth
type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ks8851_rdreg16 call above the call to request_irq and cache
the result for subsequent repeated use. A spurious interrupt may
otherwise cause a crash. Thanks to Stephen Boyd, Flavio Leitner, and
Ben Hutchings for feedback.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix MAINTAINERS file to reflect autorship.
Daniel and Ariane changed coding style but not any functional changes in the driver
itself.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change
commit 4416e9eb0b
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:12 2010 -0700
arm: msm: Fix section mismatch in smd.c.
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
The change
commit 461cbe77d0
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
This came in with the following commit 9f97da78bf
which removes asm/system.h
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David Brown <davidb@codeaurora.org>
This old fixup causes a build failure, so I remove it just like in
trout.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Building with IRQ_WORK configured results in
kernel/irq_work.c: In function ‘irq_work_run’:
kernel/irq_work.c:110: error: implicit declaration of function ‘irqs_disabled’
The appropriate header just needs to be included.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
commit 93f378883c
"Fix ia64 build errors (fallout from system.h disintegration)"
introduced arch/ia64/include/asm/cmpxchg.h as a temporary
build fix and stated:
"... leave the migration of xchg() and cmpxchg() to this new
header file for a future patch."
Migrate the appropriate chunks from asm/intrinsics.h and fix
the whitespace issues in the migrated chunk.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
commit ec2212088c
"Disintegrate asm/system.h for Alpha"
combined with commit b4816afa39
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the alpha arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Some minor whitespace fixups were done on the block of code that
created the new file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The skb struct ubuf_info callback gets passed struct ubuf_info
itself, not the arg value as the field name and the function signature
seem to imply. Rename the arg field to ctx to match usage,
add documentation and change the callback argument type
to make usage clear and to have compiler check correctness.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e675f0cc9a ("ppp: Don't stop and
restart queue on every TX packet") introduced a race condition which
could leave the net queue stopped even when the channel is no longer
busy. By calling netif_stop_queue() from ppp_start_xmit(), based on the
return value from ppp_xmit_process() but *after* all the locks have been
dropped, we could potentially do so *after* the channel has actually
finished transmitting and attempted to re-wake the queue.
Fix this by moving the netif_stop_queue() into ppp_xmit_process() under
the xmit lock. I hadn't done this previously, because it gets called
from other places than ppp_start_xmit(). But I now think it's the better
option. The net queue *should* be stopped if the channel becomes
congested due to writes from pppd, anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.
Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.
rt6_check_expired check if rt6_info.dst.from is expired.
ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
ip6_dst_destroy release the ort.
Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.
Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.
Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->root_flags is __le64 and all accesses to it go through the helpers
that do proper conversions. Except for btrfs_root_readonly(), which
checks bit 0 as in host-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The function kstrtoul() used to parse number strings in the mount
option parser is set to expect a base 10 number . This treats the octal
numbers passed for mount options such as file_mode as base10 numbers
leading to incorrect behavior.
Change the 'base' argument passed to kstrtoul from 10 to 0 to
allow it to auto-detect the base of the number passed.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Jeff Layton <jlayton@samba.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Applications using L2TP/IP sockets want to be able to bind() an L2TP/IP
socket to set the local tunnel id while leaving the auto-assigned source
address alone. So if no source address is supplied, don't overwrite
the address already stored in the socket.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The l2tp_ip socket close handler does not update the module refcount
correctly which prevents module unload after the first bind() call on
an L2TPv3 IP encapulation socket.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2e57b79cce misplaced its
parenthesis and now tx_fifo_errors will only be incremented if an
ENOMEM error is not written to the syslog.
Correct the parenthesis and indentation to the original goal of
counting all non ENOMEM errors and ratelimiting only the messages.
Signed-of-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the point of this error-handling code, alloc_skb has succeded, so free
the resulting skb by jumping to the err label.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently an oops was reported in phonet if there was a failure during
network namespace creation.
[ 163.733755] ------------[ cut here ]------------
[ 163.734501] kernel BUG at include/net/netns/generic.h:45!
[ 163.734501] invalid opcode: 0000 [#1] PREEMPT SMP
[ 163.734501] CPU 2
[ 163.734501] Pid: 19145, comm: trinity Tainted: G W 3.4.0-rc1-next-20120405-sasha-dirty #57
[ 163.734501] RIP: 0010:[<ffffffff824d6062>] [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0
[ 163.734501] RSP: 0018:ffff8800674d5ca8 EFLAGS: 00010246
[ 163.734501] RAX: 000000003fffffff RBX: 0000000000000000 RCX: ffff8800678c88d8
[ 163.734501] RDX: 00000000003f4000 RSI: ffff8800678c8910 RDI: 0000000000000282
[ 163.734501] RBP: ffff8800674d5cc8 R08: 0000000000000000 R09: 0000000000000000
[ 163.734501] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880068bec920
[ 163.734501] R13: ffffffff836b90c0 R14: 0000000000000000 R15: 0000000000000000
[ 163.734501] FS: 00007f055e8de700(0000) GS:ffff88007d000000(0000) knlGS:0000000000000000
[ 163.734501] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 163.734501] CR2: 00007f055e6bb518 CR3: 0000000070c16000 CR4: 00000000000406e0
[ 163.734501] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 163.734501] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 163.734501] Process trinity (pid: 19145, threadinfo ffff8800674d4000, task ffff8800678c8000)
[ 163.734501] Stack:
[ 163.734501] ffffffff824d5f00 ffffffff810e2ec1 ffff880067ae0000 00000000ffffffd4
[ 163.734501] ffff8800674d5cf8 ffffffff824d667a ffff880067ae0000 00000000ffffffd4
[ 163.734501] ffffffff836b90c0 0000000000000000 ffff8800674d5d18 ffffffff824d707d
[ 163.734501] Call Trace:
[ 163.734501] [<ffffffff824d5f00>] ? phonet_pernet+0x20/0x1a0
[ 163.734501] [<ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50
[ 163.734501] [<ffffffff824d667a>] phonet_device_destroy+0x1a/0x100
[ 163.734501] [<ffffffff824d707d>] phonet_device_notify+0x3d/0x50
[ 163.734501] [<ffffffff810dd96e>] notifier_call_chain+0xee/0x130
[ 163.734501] [<ffffffff810dd9d1>] raw_notifier_call_chain+0x11/0x20
[ 163.734501] [<ffffffff821cce12>] call_netdevice_notifiers+0x52/0x60
[ 163.734501] [<ffffffff821cd235>] rollback_registered_many+0x185/0x270
[ 163.734501] [<ffffffff821cd334>] unregister_netdevice_many+0x14/0x60
[ 163.734501] [<ffffffff823123e3>] ipip_exit_net+0x1b3/0x1d0
[ 163.734501] [<ffffffff82312230>] ? ipip_rcv+0x420/0x420
[ 163.734501] [<ffffffff821c8515>] ops_exit_list+0x35/0x70
[ 163.734501] [<ffffffff821c911b>] setup_net+0xab/0xe0
[ 163.734501] [<ffffffff821c9416>] copy_net_ns+0x76/0x100
[ 163.734501] [<ffffffff810dc92b>] create_new_namespaces+0xfb/0x190
[ 163.734501] [<ffffffff810dca21>] unshare_nsproxy_namespaces+0x61/0x80
[ 163.734501] [<ffffffff810afd1f>] sys_unshare+0xff/0x290
[ 163.734501] [<ffffffff8187622e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 163.734501] [<ffffffff82665539>] system_call_fastpath+0x16/0x1b
[ 163.734501] Code: e0 c3 fe 66 0f 1f 44 00 00 48 c7 c2 40 60 4d 82 be 01 00 00 00 48 c7 c7 80 d1 23 83 e8 48 2a c4 fe e8 73 06 c8 fe 48 85 db 75 0e <0f> 0b 0f 1f 40 00 eb fe 66 0f 1f 44 00 00 48 83 c4 10 48 89 d8
[ 163.734501] RIP [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0
[ 163.734501] RSP <ffff8800674d5ca8>
[ 163.861289] ---[ end trace fb5615826c548066 ]---
After investigation it turns out there were two issues.
1) Phonet was not implementing network devices but was using register_pernet_device
instead of register_pernet_subsys.
This was allowing there to be cases when phonenet was not initialized and
the phonet net_generic was not set for a network namespace when network
device events were being reported on the netdevice_notifier for a network
namespace leading to the oops above.
2) phonet_exit_net was implementing a confusing and special case of handling all
network devices from going away that it was hard to see was correct, and would
only occur when the phonet module was removed.
Now that unregister_netdevice_notifier has been modified to synthesize unregistration
events for the network devices that are extant when called this confusing special
case in phonet_exit_net is no longer needed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already synthesize events in register_netdevice_notifier and synthesizing
events in unregister_netdevice_notifier allows to us remove the need for
special case cleanup code.
This change should be safe as it adds no new cases for existing callers
of unregiser_netdevice_notifier to handle.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->ee_len is __le16, so assigning cpu_to_le32() to it is going to do
Bad Things(tm) on big-endian hosts...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Restore the original logics ("fail on mountpoints, negatives and in
case of fh_compose() failures"). Since commit 8177e (nfsd: clean up
readdirplus encoding) that got broken -
rv = fh_compose(fhp, exp, dchild, &cd->fh);
if (rv)
goto out;
if (!dchild->d_inode)
goto out;
rv = 0;
out:
is equivalent to
rv = fh_compose(fhp, exp, dchild, &cd->fh);
out:
and the second check has no effect whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
->ts_id_status gets nfs errno, i.e. it's already big-endian; no need
to apply htonl() to it. Broken by commit 174568 (NFSD: Added TEST_STATEID
operation) last year...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
nfsd_open() already returns an NFS error value; only vfs_test_lock()
result needs to be fed through nfserrno(). Broken by commit 55ef12
(nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT)
three years ago...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 94e5a85b ("ARM: earlier initialization of vectors page") made it
the responsibility of paging_init to initialise the vectors page.
This patch adds a call to early_trap_init for the !CONFIG_MMU case,
placing the vectors at CONFIG_VECTORS_BASE.
Cc: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The description for the CPU_HIGH_VECTOR Kconfig option for nommu builds
doesn't make any sense.
This patch fixes up the trivial grammatical error.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.
Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick". This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit f9a2f9c3fa. This
commit caused a regression in the I2C hwmod reset on OMAP2/3/4,
logging messages similar to these during boot:
[ 0.200378] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
[ 0.222076] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
While the original patch was intended to fix some reset-related timing
issues, it's believed that these problems were actually fixed by
commit 2800852a07 ("ARM: OMAP2+: hwmod:
Restore sysc after a reset"):
http://marc.info/?l=linux-arm-kernel&m=133410322617245&w=2
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Due to HW limitation, some IPs should not be accessed just after a
softreset. Since the current hwmod sequence is accessing the sysconfig
register just after the reset, it might lead to OCP bus error in
that case.
Add a new field in the sysconfig structure to specify a delay in usecs
needed after doing a softreset.
In the case of the ISS and FDIF modules, the L3 OCP port will be
disconnected upon a SW reset. That issue was confirmed with HW simulation
and an errata should be available soon. The HW recommendation to avoid
that is to wait for 100 OCP clk cycles, before accessing the IP.
Considering the worse case (OPP50), the L3 bus will run at 100 MHz,
so a 1 usec delay is needed. Add an x2 margin to be safe.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: dropped FDIF change for now since the hwmod data is not
yet upstream; the FDIF change will need to be added later once the FDIF
data is merged]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If cs42l73_get_mclkx_coeff() returns < 0 (which it can) in
sound/soc/codecs/cs42l73.c::cs42l73_set_mclk(), then we'll be using
the (negative) return value as array index on the very next line of
code - that's bad.
Catch the negative return value and propagate it to the caller (which
checks for it) and things are a bit more sane :-)
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In sound/pci/hda/patch_realtek.c::alc_auto_fill_dac_nids(), in the
'for (;;)' loop, if the 'badness' value returned from
fill_and_eval_dacs() is negative, then we'll return from the function
without freeing the memory we allocated for 'best_cfg', thus leaking.
Fix the leak by kfree()'ing the memory when badness is negative.
While I was there I also noticed some trailing whitespace in the
function that I removed (along with all other trailing whitespace in
the file) - it didn't seem worth-while to do that as two patches, so I
hope it's OK that I just did it all as one patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull infiniband fix from Roland Dreier:
"Add a fix for a bug hit by Alexey Shvetsov in ib_srtp that hits on
non-mlx4 hardware."
* tag 'srpt-srq-type' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srpt: Set srq_type to IB_SRQT_BASIC
We've now fixed IS_ENABLED() and friends to not require any special
"__enabled_" prefixed versions of the normal Kconfig options, so delete
the last traces of them being generated.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 953742c8fe.
Dumping two lines into autoconf.h for all existing Kconfig options
results in a giant file (~16k lines) we have to process each time we
compile something. We've weaned IS_ENABLED() and similar off of
requiring the __enabled_ definitions so now we can revert the change
which caused all the extra lines.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using IS_ENABLED() within C (vs. within CPP #if statements) in its
current form requires us to actually define every possible bool/tristate
Kconfig option twice (__enabled_* and __enabled_*_MODULE variants).
This results in a huge autoconf.h file, on the order of 16k lines for a
x86_64 defconfig.
Fixing IS_ENABLED to be able to work on the smaller subset of just
things that we really have defined is step one to fixing this. Which
means it has to not choke when fed non-enabled options, such as:
include/linux/netdevice.h:964:1: warning: "__enabled_CONFIG_FCOE_MODULE" is not defined [-Wundef]
The original prototype of how to implement a C and preprocessor
compatible way of doing this came from the Google+ user "comex ." in
response to Linus' crowdsourcing challenge for a possible improvement on
his earlier C specific solution:
#define config_enabled(x) (__stringify(x)[0] == '1')
In this implementation, I've chosen variable names that hopefully make
how it works more understandable.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A user reported that booting his box up with btrfs root on 3.4 was way
slower than on 3.3 because I removed the ideal caching code. It turns out
that we don't load the free space cache if we're in a commit for deadlock
reasons, but since we're reading the cache and it hasn't changed yet we are
safe reading the inode and free space item from the commit root, so do that
and remove all of the deadlock checks so we don't unnecessarily skip loading
the free space cache. The user reported this fixed the slowness. Thanks,
Tested-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Pull USB fixes from Greg KH:
"Here are a number of fixes for the USB core and drivers for 3.4-rc2
Lots of tiny xhci fixes here, a few usb-serial driver fixes and new
device ids, and a smattering of other minor fixes in different USB
drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
USB: update usbtmc api documentation
xHCI: Correct the #define XHCI_LEGACY_DISABLE_SMI
xHCI: use gfp flags from caller instead of GFP_ATOMIC
xHCI: add XHCI_RESET_ON_RESUME quirk for VIA xHCI host
USB: fix bug of device descriptor got from superspeed device
xhci: Fix register save/restore order.
xhci: Restore event ring dequeue pointer on resume.
xhci: Don't write zeroed pointers to xHC registers.
xhci: Warn when hosts don't halt.
xhci: don't re-enable IE constantly
usb: xhci: fix section mismatch in linux-next
xHCI: correct to print the true HSEE of USBCMD
USB: serial: fix race between probe and open
UHCI: hub_status_data should indicate if ports are resuming
EHCI: keep track of ports being resumed and indicate in hub_status_data
USB: fix race between root-hub suspend and remote wakeup
USB: sierra: add support for Sierra Wireless MC7710
USB: ftdi_sio: fix race condition in TIOCMIWAIT, and abort of TIOCMIWAIT when the device is removed
USB: ftdi_sio: fix status line change handling for TIOCMIWAIT and TIOCGICOUNT
USB: don't ignore suspend errors for root hubs
...
Pull tty and serial fixes from Greg KH:
"Here are some tty and serial fixes for 3.4-rc2.
Most important here is the pl011 fix, which has been reported by about
100 different people, which means more people use it than I expected
:)
There are also some 8250 driver reverts due to some problems reported
by them. And other minor fixes as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pch_uart: Add Kontron COMe-mTT10 uart clock quirk
pch_uart: Fix MSI setting issue
serial/8250_pci: add a "force background timer" flag and use it for the "kt" serial port
Revert "serial/8250_pci: setup-quirk workaround for the kt serial controller"
Revert "serial/8250_pci: init-quirk msi support for kt serial controller"
tty/serial/omap: console can only be built-in
serial: samsung: fix omission initialize ulcon in reset port fn()
printk(): add KERN_CONT where needed in hpet and vt code
tty/serial: atmel_serial: fix RS485 half-duplex problem
tty: serial: altera_uart: Check for NULL platform_data in probe.
isdn/gigaset: use gig_dbg() for debugging output
omap-serial: Fix the error handling in the omap_serial probe
serial: PL011: move interrupt clearing
Pull staging tree fixes from Greg KH:
"Here are a number of bugfixes for the drivers/staging/ portion of the
kernel that have been reported recently.
Nothing major here, with maybe the exception of the ramster code can
now be built so it is enabled in the build again, and lots of memory
leaks that people like to have fixed on their systems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: fix mem leaks in __persistent_ram_init()
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
staging: iio: hmc5843: Fix crash in probe function.
staging/xgifb: fix display on XGI Volari Z11m cards
Staging: android: timed_gpio: Fix resource leak in timed_gpio_probe error paths
android: make persistent_ram based drivers depend on HAVE_MEMBLOCK
staging: iio: ak8975: Remove i2c client data corruption
staging: drm/omap: move where DMM driver is registered
staging: zsmalloc: fix memory leak
Staging: rts_pstor: off by one in for loop
staging: ozwpan: Added new maintainer for ozwpan
staging:rts_pstor:Avoid "Bad target number" message when probing driver
staging:rts_pstor:Fix possible panic by NULL pointer dereference
Staging: vt6655-6: check keysize before memcpy()
staging/media/as102: Don't call release_firmware() on uninitialized variable
staging:iio:core add missing increment of loop index in iio_map_array_unregister()
staging: ramster: unbreak my heart
staging/vme: Fix module parameters
staging: sep: Fix sign of error
Pull driver core and kobject fixes from Greg KH:
"Here are some minor fixes for the driver core and kobjects that people
have reported recently.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: provide more diagnostic info for kobject_add_internal() failures
sysfs: handle 'parent deleted before child added'
sysfs: Prevent crash on unset sysfs group attributes
sysfs: Update the name hash for an entry after changing the namespace
drivers/base: fix compiler warning in SoC export driver - idr should be ida
drivers/base: Remove unneeded spin_lock_init call for soc_lock
Pull a fix for the recent irqdomain bug fixes from Grant Likely:
"I flubbed one patch in the last pull request which broke a format
string on 64 bit platforms. Here's the fix."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irq_domain: fix type mismatch in debugfs output format
sizeof(void*) returns an unsigned long, but it was being used as a width parameter to a "%-*s" format string which requires an int. On 64 bit platforms this causes a type mismatch:
linux/kernel/irq/irqdomain.c:575: warning: field width should have type
'int', but argument 6 has type 'long unsigned int'
This change casts the size to an int so printf gets the right data type.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Pull trivial perf build failure fix from Thomas Gleixner.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix getrusage() related build failure on glibc trunk
Pull timer fixes from Thomas Gleixner:
"The itimer removal one is not strictly a fix, but I really wanted to
avoid a rebase of the urgent ones."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource: Load the ACPI PM clocksource asynchronously"
clockevents: tTack broadcast device mode change in tick_broadcast_switch_to_oneshot()
itimer: Use printk_once instead of WARN_ONCE
nohz: Fix stale jiffies update in tick_nohz_restart()
tick: Document TICK_ONESHOT config option
proc: stats: Use arch_idle_time for idle and iowait times if available
itimer: Schedule silent NULL pointer fixup in setitimer() for removal
Pull x86 fixes from Thomas Gleixner.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Use correct byte-sized register constraint in __add()
x86: Use correct byte-sized register constraint in __xchg_op()
x86: vsyscall: Use NULL instead 0 for a pointer argument
If, in __persistent_ram_init(), the call to
persistent_ram_buffer_init() fails or the call to
persistent_ram_init_ecc() fails then we fail to free the memory we
allocated to 'prz' with kzalloc() - thus leaking it.
To prevent the leaks I consolidated all error exits from the function
at a 'err:' label at the end and made all error cases jump to that
label where we can then make sure we always free 'prz'. This is safe
since all the situations where the code bails out happen before 'prz'
has been stored anywhere and although we'll do a redundant kfree(NULL)
call in the case of kzalloc() itself failing that's OK since kfree()
deals gracefully with NULL pointers and I felt it was more important
to keep all error exits at a single location than to avoid that one
harmless/redundant kfree() on a error path.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Colin Cross <ccross@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If copy_to_user() fails in the WLAN_CMD_GET_NODE_LIST case of the
switch in drivers/staging/vt6656/ioctl.c::private_ioctl() we'll leak
the memory allocated to 'pNodeList'. Fix that by kfree'ing the memory
in the failure case.
Also remove a pointless cast (to type 'PSNodeList') of a kmalloc()
return value - kmalloc() returns a void pointer that is implicitly
converted, so there is no need for an explicit cast.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (14 patches)
panic: fix stack dump print on direct call to panic()
drivers/rtc/rtc-pl031.c: enable clock on all ST variants
Revert "mm: vmscan: fix misused nr_reclaimed in shrink_mem_cgroup_zone()"
hugetlb: fix race condition in hugetlb_fault()
drivers/rtc/rtc-twl.c: use static register while reading time
drivers/rtc/rtc-s3c.c: add placeholder for driver private data
drivers/rtc/rtc-s3c.c: fix compilation error
MAINTAINERS: add PCDP console maintainer
memcg: do not open code accesses to res_counter members
drivers/rtc/rtc-efi.c: fix section mismatch warning
drivers/rtc/rtc-r9701.c: reset registers if invalid values are detected
drivers/char/random.c: fix boot id uniqueness race
memcg: fix broken boolen expression
memcg: fix up documentation on global LRU
Pull networking fixes from David Miller:
1) Fix bluetooth userland regression reported by Keith Packard, from
Gustavo Padovan.
2) Revert ath9k PS idle change, from Sujith Manoharan.
3) Correct default TCP memory limits (again), from Eric Dumazet.
4) Fix tcp_rcv_rtt_update() accidental use of unscaled RTT, from Neal
Cardwell.
5) We made a facility for layers like wireless to say how much tailroom
they need in the SKB for link layer stuff such as wireless
encryption etc., but TCP works hard to fill every SKB out to the end
defeating this specification.
This leads to every TCP packet getting reallocated by the wireless
code in order to have the right amount of tailroom available.
Fix TCP to only fill SKBs out to the real amount of data area it
asked for during the allocation, this way it won't eat into the
slack added for the device's tailroom needs.
Reported by Marc Merlin and fixed by Eric Dumazet.
6) Leaks, endian bugs, and new device IDs in bluetooth from Santosh
Nayak, João Paulo Rechi Vita, Cho, Yu-Chen, Andrei Emeltchenko,
AceLan Kao, and Andrei Emeltchenko.
7) OOPS on tty_close fix in bluetooth's hci_ldisc from Johan Hovold.
8) netfilter erroneously scales TCP window twice, fix from Changli Gao.
9) Memleak fix in wext-core from Julia Lawall.
10) Consistently handle invalid TCP packets in ipv4 vs. ipv6 conntrack,
from Jozsef Kadlecsik.
11) Validate IP header length properly in netfilter conntrack's
ipv4_get_l4proto().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
NFC: Fix the LLCP Tx fragmentation loop
rtlwifi: Add missing DMA buffer unmapping for PCI drivers
rtlwifi: Preallocate USB read buffers and eliminate kalloc in read routine
tcp: avoid order-1 allocations on wifi and tx path
net: allow pskb_expand_head() to get maximum tailroom
bridge: Do not send queries on multicast group leaves
MAINTAINERS: Mark NATSEMI driver as orphan'd.
tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample
tcp: restore correct limit
Revert "ath9k: fix going to full-sleep on PS idle"
rt2x00: Fix rfkill_polling register function.
bcma: fix build error on MIPS; implicit pcibios_enable_device
netfilter: nf_conntrack: fix incorrect logic in nf_conntrack_init_net
netfilter: nf_ct_ipv4: packets with wrong ihl are invalid
netfilter: nf_ct_ipv4: handle invalid IPv4 and IPv6 packets consistently
net/wireless/wext-core.c: add missing kfree
rtlwifi: Fix oops on rate-control failure
mac80211: Convert WARN_ON to WARN_ON_ONCE
rtlwifi: rtl8192de: Fix firmware initialization
nl80211: ensure interface is up in various APIs
...
Pull drm fixes from Dave Airlie:
"Mostly exynos and intel.
Intel has 3 regression fixers (more info in intel merge commit), along
with some other make hw work fixes, exynos has some cleanups and an
ioctl fix.
A couple of radeon fixes, couple of build fixes, and a savage
userspace interface possible overflow fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (23 commits)
drm/exynos: fixed exynos broken ioctl
drm/i915: clear fencing tracking state when retiring requests
drm/exynos: fix to pointer manager member of struct exynos_drm_subdrv
drm/exynos: fix struct for operation callback functions to driver name
drm/exynos: use define instead of default_win member in struct mixer_context
drm/exynos: rename s/HDMI_OVERLAY_NUMBER/MIXER_WIN_NR
drm/exynos: remove unused codes in hdmi and mixer
drm/exynos: remove unnecessary type conversion of hdmi and mixer
drm/i915: make rc6 module parameter read-only
drm/i915: implement ColorBlt w/a
drm/i915/ringbuffer: Exclude last 2 cachlines of ring on 845g
Revert "drm/i915: reenable gmbus on gen3+ again"
drm/radeon: only add the mm i2c bus if the hw_i2c module param is set
vgaarb.h: fix build warnings
drm/i915: properly compute dp dithering for user-created modes
drm/radeon/kms: fix DVO setup on some r4xx chips
drm/savage: fix integer overflows in savage_bci_cmdbuf()
drm/radeon: replace udelay with mdelay for long timeouts
drm/i915: Finish any pending operations on the framebuffer before disabling
drm/i915: Removed IVB forced enable of sprite dest key.
...
Pull a few more fixes for md from NeilBrown:
"Two are tagged for -stable. They can cause an oops, but very rarely."
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/bitmap: prevent bitmap_daemon_work running while initialising bitmap
md/raid1,raid10: Fix calculation of 'vcnt' when processing error recovery.
MD: Bitmap version cleanup.
Commit 6e6f0a1f0f ("panic: don't print redundant backtraces on oops")
causes a regression where no stack trace will be printed at all for the
case where kernel code calls panic() directly while not processing an
oops, and of course there are 100's of instances of this type of call.
The original commit executed the check (!oops_in_progress), but this will
always be false because just before the dump_stack() there is a call to
bust_spinlocks(1), which does the following:
void __attribute__((weak)) bust_spinlocks(int yes)
{
if (yes) {
++oops_in_progress;
The proper way to resolve the problem that original commit tried to
solve is to avoid printing a stack dump from panic() when the either of
the following conditions is true:
1) TAINT_DIE has been set (this is done by oops_end())
This indicates and oops has already been printed.
2) oops_in_progress > 1
This guards against the rare case where panic() is invoked
a second time, or in between oops_begin() and oops_end()
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: <stable@vger.kernel.org> [3.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c38446cc65.
Before the commit, the code makes senses to me but not after the commit.
The "nr_reclaimed" is the number of pages reclaimed by scanning through
the memcg's lru lists. The "nr_to_reclaim" is the target value for the
whole function. For example, we like to early break the reclaim if
reclaimed 32 pages under direct reclaim (not DEF_PRIORITY).
After the reverted commit, the target "nr_to_reclaim" is decremented each
time by "nr_reclaimed" but we still use it to compare the "nr_reclaimed".
It just doesn't make sense to me...
Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The race is as follows:
Suppose a multi-threaded task forks a new process (on cpu A), thus
bumping up the ref count on all the pages. While the fork is occurring
(and thus we have marked all the PTEs as read-only), another thread in
the original process (on cpu B) tries to write to a huge page, taking an
access violation from the write-protect and calling hugetlb_cow(). Now,
suppose the fork() fails. It will undo the COW and decrement the ref
count on the pages, so the ref count on the huge page drops back to 1.
Meanwhile hugetlb_cow() also decrements the ref count by one on the
original page, since the original address space doesn't need it any
more, having copied a new page to replace the original page. This
leaves the ref count at zero, and when we call unlock_page(), we panic.
fork on CPU A fault on CPU B
============= ==============
...
down_write(&parent->mmap_sem);
down_write_nested(&child->mmap_sem);
...
while duplicating vmas
if error
break;
...
up_write(&child->mmap_sem);
up_write(&parent->mmap_sem); ...
down_read(&parent->mmap_sem);
...
lock_page(page);
handle COW
page_mapcount(old_page) == 2
alloc and prepare new_page
...
handle error
page_remove_rmap(page);
put_page(page);
...
fold new_page into pte
page_remove_rmap(page);
put_page(page);
...
oops ==> unlock_page(page);
up_read(&parent->mmap_sem);
The solution is to take an extra reference to the page while we are
holding the lock on it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC stores time and date in several registers. Due to the fact that
these registers can't be read instantaneously, there is a chance that
reading from counting registers gives an error of one minute, one hour,
one day, etc.
To address this issue, the RTC has hardware support to copy the RTC
counting registers to static shadowed registers. The current
implementation does not use this feature, and in a stress test, we can
reproduce this error at a rate of around two times per 300000 readings.
Fix the implementation to ensure that the right snapshot of time is
captured.
Signed-off-by: Konstantin Shlyakhovoy <x0155534@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: linux-omap <linux-omap@vger.kernel.org>
Acked-by: Mykola Oleksiienko <x0174904@ti.com>
Acked-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver data field is a pointer, hence assigning that to an integer results
in compilation warnings.
Fixes following compilation warnings:
drivers/rtc/rtc-s3c.c: In function `s3c_rtc_get_driver_data':
drivers/rtc/rtc-s3c.c:452:3: warning: return makes integer from pointer without a cast [enabled by default]
drivers/rtc/rtc-s3c.c: At top level:
drivers/rtc/rtc-s3c.c:674:3: warning: initialization makes pointer from integer without a cast [enabled by default]
drivers/rtc/rtc-s3c.c:674:3: warning: (near initialization for `s3c_rtc_dt_match[1].data') [enabled by default]
drivers/rtc/rtc-s3c.c:677:3: warning: initialization makes pointer from integer without a cast [enabled by default]
drivers/rtc/rtc-s3c.c:677:3: warning: (near initialization for `s3c_rtc_dt_match[2].data') [enabled by default]
drivers/rtc/rtc-s3c.c:680:3: warning: initialization makes pointer from integer without a cast [enabled by default]
drivers/rtc/rtc-s3c.c:680:3: warning: (near initialization for `s3c_rtc_dt_match[3].data') [enabled by default]
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this error:
drivers/rtc/rtc-s3c.c: At top level:
drivers/rtc/rtc-s3c.c:671:3: error: request for member `data' in something not a structure or union
drivers/rtc/rtc-s3c.c:674:3: error: request for member `data' in something not a structure or union
drivers/rtc/rtc-s3c.c:677:3: error: request for member `data' in something not a structure or union
drivers/rtc/rtc-s3c.c:680:3: error: request for member `data' in something not a structure or union
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should use the accessor res_counter_read_u64 for that.
Although a purely cosmetic change is sometimes better delayed, to avoid
conflicting with other people's work, we are starting to have people
touching this code as well, and reproducing the open code behavior
because that's the standard =)
Time to fix it, then.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
efi_rtc_init() uses platform_driver_probe(), so there's no need to also
set efi_rtc_driver's probe member (as it won't be used anyway). This
fixes a modpost section mismatch warning (as efi_rtc_probe() validly is
__init).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/sys/kernel/random/boot_id can be read concurrently by userspace
processes. If two (or more) user-space processes concurrently read
boot_id when sysctl_bootid is not yet assigned, a race can occur making
boot_id differ between the reads. Because the whole point of the boot id
is to be unique across a kernel execution, fix this by protecting this
operation with a spinlock.
Given that this operation is not frequently used, hitting the spinlock
on each call should not be an issue.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bio_alloc() has the possibility of returning NULL.
So, it is necessary to check the return value.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This fixes a regression introduced by fc67c450. spin_is_locked() always
returns 0 on UP kernels, which caused assert in get_restripe_target() to
be fired on every call from btrfs_reduce_alloc_profile() on UP systems.
Remove it completely for now, it's not clear if it's going to be needed
in future.
Reported-by: Bobby Powers <bobbypowers@gmail.com>
Reported-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Tested-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This variable is incremented from multiple contexts (module_init via
libata-lldds and the libsas discovery thread). Make it atomic to head
off any chance of libsas and libata creating duplicate ids.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Gcc version 4.6.2-12 complains that if we can't find the "nr-ports"
property in of_property_read_u32_array() then "n_ports" is used
uninitialized. Let's set it to zero in that case.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the IDE-mode SATA DeviceIDs for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We'd have to be passing bogus extent buffers for this uninit variable to
actually be used, but set it to zero just in case.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Pull irqdomain bug fixes from Grant Likely:
"This branch fixes a bug in irq_create_mapping() where an error return
from irq_alloc_desc_from() gets ignored.
It also removes irq_virq_count to fix a bug on powerpc where the
irqdomain code does not find irqs allocated above the CONFIG_NR_IRQS
boundary.
The remaining patches get rid of an completely pointless export and
fix some minor bugs in the irqdomain debug output."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irq_domain: Move irq_virq_count into NOMAP revmap
irqdomain: Fix debugfs formatting
irq_domain: correct the debugfs file name
irq: Kill pointless irqd_to_hw export
irq/irq_domain: Quit ignoring error returns from irq_alloc_desc_from().
Pull input updates from Dmitry Torokhov:
"Just a few small fixes..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: da9052 - fix memory leak in da9052_onkey_probe()
Input: gpio_mouse - use linux/gpio.h rather than asm/gpio.h
Input: trackpoint - use psmouse_fmt() for messages
Input: elantech - v4 is a clickpad, with only one button
Input: elantech - reset touchpad before configuring it
Input: sentelic - filter taps in absolute mode
Input: tps6507x-ts - fix MODULE_ALIAS to match driver name
Pull vfs fixes from Al Viro:
"Regression fix in mtdchar_open(), fix for a really old leak
(almost never hit in practice - it's a b0rken failure exit in
simple_fill_super()) and a typo fix in vfs.txt (misspelled
method type)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix in Documentation/filesystems/vfs.txt
dentry leak in simple_fill_super() failure exit
fix breakage in mtdchar_open(), sanitize failure exits
Line widgets had not been included in either the power up or power down
sequences so if a widget had an event associated with it that event would
never be run. Fix this minimally by adding them to the sequences, we
should probably be doing away with the specific widget types as they all
have the same priority anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A user reported that setting model=imac24 used to allow sound to work on their
Mac Pro 5,1 machine. Commit 5671087ffa "Move ALC885 macpro and imac24 models
to auto-parser" removed this model option. All Mac machines are now explicitly
handled with a quirk and the auto-parser. This adds a quirk for the device
found on the Mac Pro 5,1 machines.
This (partially) fixes https://bugzilla.redhat.com/show_bug.cgi?id=808559
[sorted the new entry in the ID number order by tiwai]
Reported-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 5500cdbe14.
We've had a number of complaints of early enospc that bisect down
to this patch. We'll hae to fix the reservations differently.
CC: stable@kernel.org
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed exynos broken ioctl
drm/exynos: fix to pointer manager member of struct exynos_drm_subdrv
drm/exynos: fix struct for operation callback functions to driver name
drm/exynos: use define instead of default_win member in struct mixer_context
drm/exynos: rename s/HDMI_OVERLAY_NUMBER/MIXER_WIN_NR
drm/exynos: remove unused codes in hdmi and mixer
drm/exynos: remove unnecessary type conversion of hdmi and mixer
drm/exynos: add format list of plane
drm/exynos: fixed duplicated page allocation bug.
drm/exynos: fixed page align and code clean.
Daniel Vetter writes:
3 regression fixes:
- disable gmbus again, too broken for 3.4, we'll try again for 3.5
- dp bandwidth computation fix, we've lost the 6bpc dithering flag
sometimes, this is a 3.3 regression (maybe even earlier for some
configurations).
- fix resume regression caused by the gen2/3 fencing fix merged into -rc2.
And a few other fixes:
- gpu hang fix for i845 (Chris)
- sprite fix (Armin Reese)
- crtc disable vs. scanlinewait race fix (Chris)
- rc6 module option read-only, it confused testers (Jesse)
- fbc related blitter death hw workaround, note that we disable fbc on snb
by default anyway.
With these fixes we have one 3.4 regression outstanding: One of the
cleanup patches for the interlaced support managed to confuse the lvds
panel fitter when upscaling. The root-cause is still unclear, but test
patches are awaiting feedback from the reporter.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear fencing tracking state when retiring requests
drm/i915: make rc6 module parameter read-only
drm/i915: implement ColorBlt w/a
drm/i915/ringbuffer: Exclude last 2 cachlines of ring on 845g
Revert "drm/i915: reenable gmbus on gen3+ again"
drm/i915: properly compute dp dithering for user-created modes
drm/i915: Finish any pending operations on the framebuffer before disabling
drm/i915: Removed IVB forced enable of sprite dest key.
Hi Greg,
Here's 11 xHCI bug fixes for 3.4.
Some of the patches fix issues with crashes on system resume related to
VIA xHCI host controllers accessing bad memory addresses. The patches
change the register restore ordering, so I had several vendors confirm
that the patches don't break their xHCI hosts.
Elric Fu confirms this patchset fixes the VIA issue, Alex He confirms
the changes does not break suspend/resume on AMD xHCI systems, and I've
made sure it doesn't break Intel host controllers. I have not heard
back from Felipe about the TI host, so at this point, I'm just going to
send them off.
Several of the patches are marked for stable. Please pull.
Sarah Sharp
Since commit 96104eda01 ("RDMA/core: Add SRQ type field"), kernel
users of SRQs need to specify srq_type = IB_SRQT_BASIC in struct
ib_srq_init_attr, or else most low-level drivers will fail in
when srpt_add_one() calls ib_create_srq() and gets -ENOSYS.
(mlx4_ib works OK nearly all of the time, because it just needs
srq_type != IB_SRQT_XRC. And apparently nearly everyone using
ib_srpt is using mlx4 hardware)
Reported-by: Alexey Shvetsov <alexxy@gentoo.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch (as1539) fixes a minor bug in the mass-storage gadget
drivers. When an unknown command is received, the error code sent
back is "Invalid Field in CDB" rather than "Invalid Command". This is
because the bitmask of CDB bytes allowed to be nonzero is incorrect.
When handling an unknown command, we don't care which command bytes
are nonzero. All the bits in the mask should be set, not just eight
of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <Michal Nazarewicz <mina86@mina86.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 9ad63986c6 (pda_power: Add support for using otg transceiver events)
converted the pda-power driver to use otg events to determine the status
of the power supply.
As gpio-vbus didn't use otg events until now, this change breaks setups
of pda-power with a gpio-vbus transceiver.
This patch adds the necessary otg events and notifiers to gpio-vbus.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Dima Zavin <dima@android.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the ISO C standard compliant form instead of the gcc extension in the
interface definition.
Reported-by: Shachar Sharon <ssnail@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
this patch removes the pointer of uint64_t *edid. it should be just
a uint64_t.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The current virtio block's naming algorithm just supports 18278
(26^3 + 26^2 + 26) disks. If there are more virtio blocks,
there will be disks with the same name.
Based on commit 3e1a7ff8a0, add
a function "virtblk_name_format()" for virtio block to support mass
of disks naming.
Notes:
- Our naming scheme is ugly. We are stuck with it
for virtio but don't use it for any new driver:
new drivers should name their devices PREFIX%d
where the sequence number can be allocated by ida
- sd_format_disk_name has exactly the same logic.
Moving it to a central place was deferred over worries
that this will make people keep using the legacy naming
in new drivers.
We kept code idential in case someone wants to deduplicate later.
Signed-off-by: Ren Mingxin <renmx@cn.fujitsu.com>
Acked-by: Asias He <asias@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit ea5d404655
broke build for the vhost test module used
by tools/virtio. Fix it up.
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fixes a resume regression introduced in
commit 7dd4906586
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Mar 21 10:48:18 2012 +0000
drm/i915: Mark untiled BLT commands as fenced on gen2/3
which fixed fencing tracking for untiled blt commands.
A side effect of that patch was that now also untiled objects have a
non-zero obj->last_fenced_seqno to track when a fence can be set up
after a pipelined tiling change. Unfortunately this was only cleared
by the fence setup and teardown code, resulting in tons of untiled but
inactive objects with non-zero last_fenced_seqno.
Now after resume we completely reset the seqno tracking, both on the
driver side (by setting dev_priv->next_seqno = 1) and on the hw side
(by allocating a new hws page, which contains the seqnos). Hilarity
and indefinite waits ensued from the stale seqnos in
obj->last_fenced_seqno from before the suspend.
The fix is to properly clear the fencing tracking state like we
already do for the normal gpu rendering while moving objects off the
active list.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch replaces the old global setting of irq_virq_count that is only
used by the NOMAP mapping and instead uses a revmap_data property so that
the maximum NOMAP allocation can be set per NOMAP irq_domain.
There is exactly one user of irq_virq_count in-tree right now: PS3.
Also, irq_virq_count is only useful for the NOMAP mapping. So,
instead of having a single global irq_virq_count values, this change
drops it entirely and added a max_irq argument to irq_domain_add_nomap().
That makes it a property of an individual nomap irq domain instead of
a global system settting.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
If a bitmap is added while the array is active, it is possible
for bitmap_daemon_work to run while the bitmap is being
initialised.
This is particularly a problem if bitmap_daemon_work sees
bitmap->filemap as non-NULL before it has been filled in properly.
So hold bitmap_info.mutex while filling in ->filemap
to prevent problems.
This patch is suitable for any -stable kernel, though it might not
apply cleanly before about 3.1.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.
This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Add GPIO1 setup explicitly for Acer Aspire 493x & co.
This could be set by alc_auto_init_amp(), but it's safer to set it
more explicitly in the fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
bitmap_new_disk_sb() would still create V3 bitmap superblock
with host-endian layout.
Perhaps I'm confused, but shouldn't bitmap_new_disk_sb() be
creating a V4 bitmap superblock instead, that is portable,
as per comment in bitmap.h?
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The struct exynos_drm_manager has to exist for exynos drm sub driver
using encoder and connector. If it isn't NULL to member of struct
exynos_drm_subdrv, will create encoder and connector else will not. And
the is_local member also doesn't need.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The mixer driver and hdmi driver have each operation callback functions
and they is registered to hdmi common driver. Their struct names in hdmi
common driver include display, manager and overlay. It confuses to
appear whose operation and two driver cannot register same operation
callback functions at the same time. Use their struct names to driver
name.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The default_win member in struct mixer_context isn't change its value
after initialized to 0, so it's better using to define.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI_OVERLAY_NUMBER is specific of mixer driver and be used "windows
layer" term in exynos user manaual, so rename it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some members in struct mixer_context aren't used and the define
HDMI_OVERLAY_NUMBER is unused in hdmi driver, remove them.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When the void pointer type variable is assigned to the specific pointer
type variable, don't need to do type conversion.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If, in drivers/input/misc/da9052_onkey.c::da9052_onkey_probe(), the
call to either kzalloc() or input_allocate_device() fails then we will
return -ENOMEM from the function without freeing the other allocation
that may have succeeded, thus we leak either the memory allocated for
'onkey' or the memory allocated for 'input_dev' if one succeeds and
the other fails.
Fix that by jumping to the 'err_free_mem' label at the end of the
function that properly cleans up rather than returning directly.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull powerpc fixes from Benjamin Herrenschmidt:
"Fixes for two nasty regression affecting powerpc in 3.4."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix typo in runlatch code
powerpc: Fix page fault with lockdep regression
Allow blank user= and ip= mount option. Also clean up redundant
checks for NULL values since the token parser will not actually
match mount options with NULL values unless explicitly specified.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Acked-by: Jeff Layton <jlayton@samba.org>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We've been adding new mappings, but not destroying old mappings.
This can lead to a page leak as pages are pinned using
get_user_pages, but only unpinned with put_page if they still
exist in the memslots list on vm shutdown. A memslot that is
destroyed while an iommu domain is enabled for the guest will
therefore result in an elevated page reference count that is
never cleared.
Additionally, without this fix, the iommu is only programmed
with the first translation for a gpa. This can result in
peer-to-peer errors if a mapping is destroyed and replaced by a
new mapping at the same gpa as the iommu will still be pointing
to the original, pinned memory address.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This reverts commit b519508298.
The reason for this revert is that making the frequency verification
preemptible and interruptible is not working reliably. Michaels
machine failed to use PM-timer with the message:
PM-Timer running at invalid rate: 113% of normal - aborting.
That's not a surprise as the frequency verification does rely on
interrupts being disabled. With a async scheduled thread there is no
guarantee to achieve the same result. Also some driver might fiddle
with the CTC channel 2 during the verification period, which makes the
result even more random and unpredictable.
This can be solved by using the same mechanism as we use in the
deferred TSC validation code, but that only will work if we verified a
working HPET _BEFORE_ trying to do the PM-Timer lazy validation.
So for now reverting is the safe option.
Bisected-by: Michael Witten <mfwitten@gmail.com>
Cc: Arjan van de Ven <arjanvandeven@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <alpine.LFD.2.02.1204112303270.2542@ionos>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Allow a v3 unchecked open of a non-regular file succeed as if it were a
lookup; typically a client in such a case will want to fall back on a
local open, so succeeding and giving it the filehandle is more useful
than failing with nfserr_exist, which makes it appear that nothing at
all exists by that name.
Similarly for v4, on an open-create, return the same errors we would on
an attempt to open a non-regular file, instead of returning
nfserr_exist.
This fixes a problem found doing a v4 open of a symlink with
O_RDONLY|O_CREAT, which resulted in the current client returning EEXIST.
Thanks also to Trond for analysis.
Cc: stable@kernel.org
Reported-by: Orion Poplawski <orion@cora.nwra.com>
Tested-by: Orion Poplawski <orion@cora.nwra.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Pull infiniband fixes from Roland Dreier:
"Fix a regression in the /sys/class/infiniband/.../rate attribute --
old kernels used to just return something, even if the underlying
value was out-of-bounds, while 3.4-rc1 returned EINVAL to userspace.
This breaks some applications that check for the error, so go back to
the old behavior."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Don't return EINVAL from sysfs rate attribute for invalid speeds
IB/mlx4: Don't return an invalid speed when a port is down
The current version of rtlwifi for USB operations uses kmalloc to
acquire a 32-bit buffer for each read of the device. When
_usb_read_sync() is called with the rcu_lock held, the result is
a "sleeping function called from invalid context" BUG. This is
reported for two cases in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
The first case has the lock originating from within rtlwifi and could
be fixed by rearranging the locking; however, the second originates from
within mac80211. The kmalloc() call is removed from _usb_read_sync()
by creating a ring buffer pointer in the private area and
allocating the buffer data in the probe routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [This version good for 3.3+ - different patch for 3.2 - 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull arch/tile fixes from Chris Metcalf:
"This is one important change from Srivatsa Bhat that got dropped when
I put together my pull request for -rc2, plus a trivial change to
remove a compiler warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: avoid unused variable warning in proc.c for tilegx
tile/CPU hotplug: Add missing call to notify_cpu_starting()
Pull sound fixes from Takashi Iwai:
- A series of fixes for Conexant 20549 HD-audio codec chip
- A workaround for HDMI hotplug debug prints that annoyed people
- A fix for the new support of platform DAPM contexts
- Many driver-specific minor fixes
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - hide HDMI/ELD printks unless snd.debug=2
ALSA: sound/isa/sscape.c: add missing resource-release code
sound: sound/oss/msnd_pinnacle.c: add vfrees
ALSA: hda - clean up CX20549 test mixer setup
ALSA: hda - CX20549 doesn't need pin_amp_workaround.
ALSA: hda - Remove CD control from model=benq for CX20549
ALSA: hda - fix record volume controls of CX20459 ("Venice")
ALSA: hda - Rename capture sources of CX20549 to match common conventions
ALSA: hda - Fix proc output for ADC amp values of CX20549
ASoC: tegra: fix i2s compilation when !CONFIG_DEBUG_FS
ASoC: set idle_bias_off=1 for all platform DAPM contexts
ASoC: imx-audmux: Check for NULL pointer
ASoC: imx-audmux: Fix ssi port numbers in sysfs
ASoC: ak4642: fixup: mute needs +1 step
MAINTAINERS: Don't list everyone working on Wolfson drivers
MAINTAINERS: Add missing ASoC OMAP co-maintainer
ASoC: pxa: pxa2xx-i2s: add io.h for IOMEM macro
ASoC: tegra: ensure clocks are enabled when touching registers
ASoC: sgtl5000: Enable VAG when DAC/ADC up
ALSA: asihpi - fix return value of hpios_locked_mem_alloc()
Pull media fixes from Mauro Carvalho Chehab:
- dvb core: there is a regression found when used with xine. For
whatever unknown reason, xine (and xine-lib clients) wants that the
frontend to tell what frequency he is using even before the PLL lock
(or at least, it expects a non-zero frequency).
On DVB, the frequency is only actually known after a frequency
zig-zag seek, done by the DVB core. Anyway, the fix was trivial.
That solves Fedora BZ#808871.
- ivtv: fix a regression when selecting the language channel
- uvc: fix a race-related crash
- it913x: fixes firmware loading
- two trivial patches (a dependency issue at a radio driver at sound
Kconfig, and a warning fix on dvb).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Fix race-related crash in uvc_video_clock_update()
[media] Drivers/media/radio: Fix build error
[media] dvb_frontend: fix compiler warning
[media] it913x: fix firmware loading errors
[media] ivtv: Fix AUDIO_(BILINGUAL_)CHANNEL_SELECT regression
[media] dvb_frontend: regression fix: userspace ABI broken for xine
Pull GFS2 fixes from Steven Whitehouse
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Allow caching of rindex glock
GFS2: Make sure rindex is uptodate before starting transactions
GFS2: use depends instead of select in kconfig
GFS2: put glock reference in error patch of read_rindex_entry
Until we push the unaligned access support for tilegx, it's silly
to have arch/tile/kernel/proc.c generate a warning about an unused
variable. Extend the #ifdef to cover all the code and data for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This merges the 32- and 64-bit versions of the x86 strncpy_from_user()
by just rewriting it in C rather than the ancient inline asm versions
that used lodsb/stosb and had been duplicated for (trivial) differences
between the 32-bit and 64-bit versions.
While doing that, it also speeds them up by doing the accesses a word at
a time. Finally, the new routines also properly handle the case of
hitting the end of the address space, which we have never done correctly
before (fs/namei.c has a hack around it for that reason).
Despite all these improvements, it actually removes more lines than it
adds, due to the de-duplication. Also, we no longer export (or define)
the legacy __strncpy_from_user() function (that was defined to not do
the user permission checks), since it's not actually used anywhere, and
the user address space checks are built in to the new code.
Other architecture maintainers have been notified that the old hack in
fs/namei.c will be going away in the 3.5 merge window, in case they
copied the x86 approach of being a bit cavalier about the end of the
address space.
Cc: linux-arch@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin" <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The caller is allowed to specify the GFP flags for these functions.
We should prefer their flags unless we have good reason. For
example, if we take a spin_lock ourselves we'd need to use
GFP_ATOMIC. But in this case it's safe to use the callers GFP
flags.
The callers all pass GFP_ATOMIC here, so this change doesn't affect
how the kernel behaves but we may add other callers later and this
is a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When the Seagate Goflex USB3.0 device is attached to VIA xHCI
host, sometimes the device will downgrade mode to high speed.
By the USB analyzer, I found the device finished the link
training process and worked at superspeed mode. But the device
descriptor got from the device shows the device works at 2.1.
It is very strange and seems like the device controller of
Seagate Goflex has a little confusion.
The first 8 bytes of device descriptor should be:
12 01 00 03 00 00 00 09
But the first 8 bytes of wrong device descriptor are:
12 01 10 02 00 00 00 40
The wrong device descriptor caused the initialization of mass
storage failed. After a while, the device would be recognized
as a high speed device and works fine.
This patch will warm reset the device to fix the issue after
finding the bcdUSB field of device descriptor isn't 0x0300
but the speed mode of device is superspeed.
This patch should be backported to kernels as old as 3.2, or ones that
contain the commit 75d7cf72ab "usbcore:
refine warm reset logic".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Acked-by: Andiry Xu <Andiry.Xu@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in. It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last. I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled. Therefore we need to restore the event ring registers
before we re-enable interrupts.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it. No other code in the xHCI successful resume path would
ever restore it either. Fix that.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8 "USB: xHCI: PCI power
management implementation".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: stable@vger.kernel.org
Eric Fu reports a problem with his VIA host controller fetching a zeroed
event ring pointer on resume from suspend. The host should have been
halted, but we can't be sure because that code ignores the return value
from xhci_halt(). Print a warning when the host controller refuses to
halt within XHCI_MAX_HALT_USEC (currently 16 seconds).
(Update: it turns out that the VIA host controller is reporting a halted
state when it fetches the zeroed event ring pointer. However, we still
need this warning for other host controllers.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a361 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
keyctl_session_to_parent(task) sets ->replacement_session_keyring,
it should be processed and cleared by key_replace_session_keyring().
However, this task can fork before it notices TIF_NOTIFY_RESUME and
the new child gets the bogus ->replacement_session_keyring copied by
dup_task_struct(). This is obviously wrong and, if nothing else, this
leads to put_cred(already_freed_cred).
change copy_creds() to clear this member. If copy_process() fails
before this point the wrong ->replacement_session_keyring doesn't
matter, exit_creds() won't be called.
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
After investigation, it turns out TCP uses sk_stream_alloc_skb() and
used as a convention skb_tailroom(skb) to know how many bytes of data
payload could be put in this skb (for non SG capable devices)
Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER +
sizeof(struct skb_shared_info) being above 2048)
Later, mac80211 layer need to add some bytes at the tail of skb
(IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is
available has to call pskb_expand_head() and request order-1
allocations.
This patch changes sk_stream_alloc_skb() so that only
sk->sk_prot->max_header bytes of headroom are reserved, and use a new
skb field, avail_size to hold the data payload limit.
This way, order-0 allocations done by TCP stack can leave more than 2 KB
of tailroom and no more allocation is performed in mac80211 layer (or
any layer needing some tailroom)
avail_size is unioned with mark/dropcount, since mark will be set later
in IP stack for output packets. Therefore, skb size is unchanged.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
Turns out part of the problem comes from pskb_expand_head() not using
ksize() to get exact head size given by kmalloc(). Doing the same thing
than __alloc_skb() allows more tailroom in skb and can prevent future
reallocations.
As a bonus, struct skb_shared_info becomes cache line aligned.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inline assembly in__arch_swab16p causes compile errors of the form:
*error*: *invalid* '*asm*': operand number missing after %-*letter*
The assembly uses the %O<n>/%R<n> notation but the first operand misses
the operand number, it needs to be "%O1" instead of "%O".
Reported-by: Gil Peleg <gilpeleg@servframe.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The stfle() function writes into lowcore memory when stfl_fac_list
is initialized with "S390_lowcore.stfl_fac_list = 0". For older
compilers this triggers a lowcore exception. With newer compilers
and "-OXX" compile option the bug does not show up because
the "S390_lowcore.stfl_fac_list" initialization is removed by the
compiler. The reason for thatis the incorrect "=m"
(S390_lowcore.stfl_fac_list) constraint in the stfl inline assembly.
The following shows the disassembly of the stfle() optimized code
that is inlined in the lgr_info_get() function:
000000000011325c <lgr_info_get>:
11325c: eb 9f f0 60 00 24 stmg %r9,%r15,96(%r15)
113262: c0 d0 00 29 0e 47 larl %r13,634ef0 <servi..>
113268: a7 f1 3f c0 tml %r15,16320
11326c: b9 04 00 ef lgr %r14,%r15
113270: a7 84 00 01 je 113272 <lgr_info_g..>
113274: a7 fb ff c0 aghi %r15,-64
113278: b9 04 00 c2 lgr %r12,%r2
11327c: a7 29 00 01 lghi %r2,1
113280: e3 e0 f0 98 00 24 stg %r14,152(%r15)
113286: d7 97 c0 00 c0 00 xc 0(152,%r12),0(%r12)
11328c: c0 e5 00 28 db 4c brasl %r14,62e924 <add_e..>
113292: b2 b1 00 00 stfl 0
To fix the problem we now clear the S390_lowcore.stfl_fac_list at
startup in "head.S" for all machine types before lowcore protection
is enabled.
In addition to that the "=m" constraint is replaced by "+m".
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix these:
arch/s390/kernel/perf_cpum_cf.c:180:3: warning: format '%lx'
expects argument of type 'long unsigned int',
but argument 2 has type 'int' [-Wformat]
arch/s390/kernel/perf_cpum_cf.c: In function 'cpumf_pmu_disable':
arch/s390/kernel/perf_cpum_cf.c:205:3: warning: format '%lx'
expects argument of type 'long unsigned int',
but argument 2 has type 'int' [-Wformat]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use braces for if/else/list_for_each_entry bodies if the body consists
of more than a single line. Otherwise I get confused and check if there
is something broken whenever I see these code snippets.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add TASKSTATS options, enable CRASH_DUMP, and regenerate defconfig
file with "make savedefconfig".
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Git commit 36409f6353 "use generic RCU
page-table freeing code" introduced a tlb flushing bug. Partially revert
the above git commit and go back to s390 specific page table flush code.
For s390 the TLB can contain three types of entries, "normal" TLB
page-table entries, TLB combined region-and-segment-table (CRST) entries
and real-space entries. Linux does not use real-space entries which
leaves normal TLB entries and CRST entries. The CRST entries are
intermediate steps in the page-table translation called translation paths.
For example a 4K page access in a three-level page table setup will
create two CRST TLB entries and one page-table TLB entry. The advantage
of that approach is that a page access next to the previous one can reuse
the CRST entries and needs just a single read from memory to create the
page-table TLB entry. The disadvantage is that the TLB flushing rules are
more complicated, before any page-table may be freed the TLB needs to be
flushed.
In short: the generic RCU page-table freeing code is incorrect for the
CRST entries, in particular the check for mm_users < 2 is troublesome.
This is applicable to 3.0+ kernels.
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently in the memcpy_real() function interrupts are disabled with
__arch_local_irq_stnsm(). In order to notify lockdep that interrupts
are disabled, with this patch local_irq_save() is used instead. The
function __arch_local_irq_stnsm() is still used for switching to
real mode.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch is used to fix a memory leak issue in s390/char/vmur.c.
A character device instance is allocated by cdev_alloc, the cdev_del
will not free that space if cdev_init is applied before.
Signed-off-by: Dennis Chen <dennis1.chen@amd.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extend some error paths to call dasd_sfree_request as done earlier in the
function. The error-handling code is also moved to the end of the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since there are still many Acer models that might not be covered by
the current fixup table, let's add back a few typical model names so
that user can test the fixup without recompiling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to an internal workaround master list, we need to set bit 5
of register 9400 to avoid issues with color blits.
Testing shows that this seems to fix the blitter hangs when fbc is
enabled on snb, thanks to Chris Wilson for figuring this out.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Michael "brot" Groh <michael.groh@minad.de>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 845g shares the errata with i830 whereby executing a command
within 2 cachelines of the end of the ringbuffer may cause a GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Derrik Pates reports that an utimensat with a NULL argument results in the
current time being sent from the kernel with 1 second granularity.
Reported-by: Derrik Pates <demon@now.ai>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fix build warnings by providing a struct stub since no fields of
the struct are used:
include/linux/vgaarb.h:66:9: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:66:9: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/vgaarb.h:99:34: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:109:6: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:121:8: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:140:37: warning: 'struct pci_dev' declared inside parameter list
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most code assumes that the pinctrl ops are present. Validate this when
registering a pinctrl driver. Remove the one place in the code that
was checking whether one of these non-optional ops was present.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Macros in <linux/pinctrl/machine.h> call ARRAY_SIZE(), the definition of
which eventually calls BUILD_BUG_ON_ZERO(), which is defined in
<linux/bug.h>. Include that so that every .c file using the pinctrl macros
doesn't have to do that itself.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_register_mappings is defined in core.c, so change the dependent
macro from CONFIG_MUX to CONFIG_PINCTRL.
The compile error message is:
drivers/pinctrl/core.c:886: error: redefinition of 'pinctrl_register_mappings'
include/linux/pinctrl/machine.h:160: note: previous definition of 'pinctrl_register_mappings' was here
make[2]: *** [drivers/pinctrl/core.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the irq_domain_mapping debugfs output to pad pointer
values with leading zeros so that pointer values are displayed
correctly. Otherwise you get output similar to "0x 5e0000000000000".
Also, when the irq_domain is set to 'null'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
It makes no sense to export this trivial function. Make it a static inline
instead.
This patch also drops virq_to_hw from arch/c6x since it is unused by that
architecture.
v2: Move irq_hw_number_t into types.h to fix ARM build failure
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 4bbdd45a (irq_domain/powerpc: eliminate irq_map; use
irq_alloc_desc() instead) code was added that ignores error returns
from irq_alloc_desc_from() by (silently) casting the return value to
unsigned. The negitive value error return now suddenly looks like a
valid irq number.
Commits cc79ca69 (irq_domain: Move irq_domain code from powerpc to
kernel/irq) and 1bc04f2c (irq_domain: Add support for base irq and
hwirq in legacy mappings) move this code to its current location in
irqdomain.c
The result of all of this is a null pointer dereference OOPS if one of
the error cases is hit.
The fix: Don't cast away the negativeness of the return value and then
check for errors.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: dropped addition of new 'irq' variable]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit fe1952fc0a
"powerpc: Rework runlatch code" has a nasty typo
where it uses "TLF_RUNLATCH" instead of "_TLF_RUNLATCH"
(bit number instead of bit mask), causing some flags to
be potentially lost such as _TLF_RESTORE_SIGMASK
(Brown paper bag for me ! We should be able to make
that break at compile time with a bit of magic, any
volunteer ?)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes builds where CONFIG_AUDIT is not defined and
CONFIG_SECURITY_SMACK=y.
This got introduced by the stack-usage reducation commit 48c62af68a
("LSM: shrink the common_audit_data data union").
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
1/ convert open-coded KERN_ERR+dump_stack() to WARN(), so that automated
tools pick up this warning.
2/ include the 'child' and 'parent' kobject names. This information was
useful for tracking down the case where scsi invoked device_del() on a
parent object and subsequently invoked device_add() on a child. Now the
warning looks like:
kobject_add_internal failed for target8:0:16 (error: -2 parent: end_device-8:0:24)
Pid: 2942, comm: scsi_scan_8 Not tainted 3.3.0-rc7-isci+ #2
Call Trace:
[<ffffffff8125e551>] kobject_add_internal+0x1c1/0x1f3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e659>] kobject_add_varg+0x41/0x50
[<ffffffff8125e723>] kobject_add+0x64/0x66
[<ffffffff8131124b>] device_add+0x12d/0x63a
[<ffffffff8125e0ef>] ? kobject_put+0x4c/0x50
[<ffffffff8132f370>] scsi_sysfs_add_sdev+0x4e/0x28a
[<ffffffff8132dce3>] do_scan_async+0x9c/0x145
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In scsi at least two cases of the parent device being deleted before the
child is added have been observed.
1/ scsi is performing async scans and the device is removed prior to the
async can thread running (can happen with an in-opportune / unlikely
unplug during initial scan).
2/ libsas discovery event running after the parent port has been torn
down (this is a bug in libsas).
Result in crash signatures like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
IP: [<ffffffff8115e100>] sysfs_create_dir+0x32/0xb6
...
Process scsi_scan_8 (pid: 5417, threadinfo ffff88080bd16000, task ffff880801b8a0b0)
Stack:
00000000fffffffe ffff880813470628 ffff88080bd17cd0 ffff88080614b7e8
ffff88080b45c108 00000000fffffffe ffff88080bd17d20 ffffffff8125e4a8
ffff88080bd17cf0 ffffffff81075149 ffff88080bd17d30 ffff88080614b7e8
Call Trace:
[<ffffffff8125e4a8>] kobject_add_internal+0x120/0x1e3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e641>] kobject_add_varg+0x41/0x50
[<ffffffff8125e70b>] kobject_add+0x64/0x66
[<ffffffff8131122b>] device_add+0x12d/0x63a
In this scenario the parent is still valid (because we have a
reference), but it has been device_del()'d which means its kobj->sd
pointer is NULL'd via:
device_del()->kobject_del()->sysfs_remove_dir()
...and then sysfs_create_dir() (without this fix) goes ahead and
de-references parent_sd via sysfs_ns_type():
return (sd->s_flags & SYSFS_NS_TYPE_MASK) >> SYSFS_NS_TYPE_SHIFT;
This scenario is being fixed in scsi/libsas, but if other subsystems
present the same ordering the system need not immediately crash.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio_simple_xlate() has an off-by-one bug where it checks to see if
args[0] is > ngpio instead of >=. args[0] must always be less than
ngpio because it is a zero-based enumeration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
[grant.likely: beef up commit text]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c43b874d5d (tcp: properly initialize tcp memory limits) tried
to fix a regression added in commits 4acb4190 & 3dc43e3,
but still get it wrong.
Result is machines with low amount of memory have too small tcp_rmem[2]
value and slow tcp receives : Per socket limit being 1/1024 of memory
instead of 1/128 in old kernels, so rcv window is capped to small
values.
Fix this to match comment and previous behavior.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move rt2x00rfkill_register(rt2x00dev) to rt2x00lib_probe_dev
function. It fixes of starting rfkill_poll function at the
right time if sets hard rfkill block and reboot. rt2x00mac_rfkill_poll
should be starting before bringing up the wireless interface.
Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
CC: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull sparc fixes from David Miller:
1) Build fix for LEON, from Sam Ravnborg.
2) Make the sparc side changes that go along with the infrastructure to
retry faults when blocking on a disk transfer. From Kautuk Consul.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32,leon: fix leon build
sparc/mm/fault_32.c: Port OOM changes to do_sparc_fault
sparc/mm/fault_64.c: Port OOM changes to do_sparc64_fault
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
We've only computed whether we need to fall back to 6bpc due to dp
link bandwidth constrains in mode_valid, but not mode_fixup. Under
various circumstances X likes to create new modes which then lack
proper 6bpc flags (if required), resulting in mode_fixup failures and
ultimately black screens.
Chris Wilson pointed out that we still get things wrong for bpp > 24,
but that should be fixed in another patch (and it'll be easier because
this patch consolidates the logic).
The likely culprit for this regression is
commit 3d794f87238f74d80e78a7611c7fbde8a54c85c2
Author: Keith Packard <keithp@keithp.com>
Date: Wed Jan 25 08:16:25 2012 -0800
drm/i915: Force explicit bpp selection for intel_dp_link_required
v2: Fix indentation and tune down the too bold claim that this should
fix the world. Both noticed by Chris Wilson.
v3: Try to really git add things.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48170
Cc: stable@kernel.org
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Image on Z11m cards was totally garbled due to wrong memory being
selected. Add a special handling for Z11m cards. Tested on PCIe Z11 and
Z11m cards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gpio_request fails, we need to free all allocated resources.
Current code uses wrong array index to access gpio_data array.
So current code actually frees gpio_data[i].gpio by j times.
This patch moves the error handling code to err_out and thus improves
readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m68k doesn't have memblock_reserve, which causes a build failure
with allmodconfig. Make PERSISTENT_RAM and RAM_CONSOLE depend on
HAVE_MEMBLOCK.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c client data set is of type struct indio_dev pointer and hence the
pointer returned from i2c_get_clientdata() should be assigned to
an object of type struct indio_dev and not to an object of type
struct ak8975_data.
Also in ak8975_probe() client data should be set first
before calling ak8975_setup() as it references the client data.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
CC: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not sure what triggered the change in behavior, but seems to
result in recursively acquiring a mutex and hanging on boot. But
omap_drm_init() seems a much more sane place to register the
driver for the DMM sub-device.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I already fixed the other similar for loop in this file. I'm not sure
how I missed this one. We use seg_no+1 inside the loop so we can't go
right up to the end of the loop.
Also if we don't break out of the loop then we end up past the end of
the array, but with this fix we end up on the last element.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added Rupesh Gujare to MAINTAINERS file and contact in TODO file
for ozwpan driver.
Signed-off-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid "Bad LUN" and "Bad target number" message by setting the supported
max_lun and max_id for the scsi host
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtsx_transport.c (rtsx_transfer_sglist_adma_partial):
pointer struct scatterlist *sg, which is mapped in dma_map_sg,
is used as an iterator in later transfer operation. It is corrupted and
passed to dma_unmap_sg, thus causing fatal unmap of some erroneous address.
Fix it by duplicating *sg_ptr for iterating.
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to check the we don't copy too much memory. This comes from a
copy_from_user() in the ioctl.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If, in drivers/staging/media/as102/as102_fw.c::as102_fw_upload(), the call
cmd_buf = kzalloc(MAX_FW_PKT_SIZE, GFP_KERNEL);
should fail and return NULL so that we jump to the 'error:' label,
then we'll end up calling 'release_firmware(firmware);' with
'firmware' still uninitialized - not good.
The easy fix is to just initialize 'firmware' to NULL when we declare
it, since release_firmware() deals gracefully with being passed NULL
pointers.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The just-merged ramster staging driver was dependent on a cleanup patch in
cleancache, so was marked CONFIG_BROKEN until that patch could be
merged. That cleancache patch is now merged (and the correct SHA of the
cleancache patch is 3167760f83 rather than
the one shown in the comment removed in the patch below).
So remove the CONFIG_BROKEN now and the comment that is no longer true...
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of our errors wasn't negative as intended. Fix this.
(Found by Hillf Danton)
While we are at it turn user causable messages down to dev_dbg level in the
ioctl paths.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: gadget: eliminate NULL pointer dereference (bugfix)
This patch fixes a bug which causes NULL pointer dereference in
ffs_ep0_ioctl. The bug happens when the FunctionFS is not bound (either
has not been bound yet or has been bound and then unbound) and can be
reproduced with running the following commands:
$ insmod g_ffs.ko
$ mount -t functionfs func /dev/usbgadget
$ ./null
where null.c is:
#include <fcntl.h>
#include <linux/usb/functionfs.h>
int main(void)
{
int fd = open("/dev/usbgadget/ep0", O_RDWR);
ioctl(fd, FUNCTIONFS_CLEAR_HALT);
return 0;
}
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the non-required spinlock acquire/release calls on
'queue->irqlock' from 'uvc_queue_next_buffer' routine.
This routine is called from 'video->encode' function (which translates to
either 'uvc_video_encode_bulk' or 'uvc_video_encode_isoc') in 'uvc_video.c'.
As, the 'video->encode' routines are called with 'queue->irqlock' already held,
so acquiring a 'queue->irqlock' again in 'uvc_queue_next_buffer' routine causes
a spin lock recursion.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is crucial to assign each req->context value to struct rndis.
The problem happens for multi function gadget (g_multi) when multiple
functions are calling common usb_composite_dev control request.
It might happen that *_setup method from one usb function will
alter some fields of this common request issued by other USB
function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.
Cc: stable@vger.kernel.org
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During modprobe of gadget driver, pullup is called after
udc_start. In order to make the exit path symmetric when
removing a gadget driver, call pullup before ->udc_stop.
This is needed to avoid issues with PM where udc_stop
disables the module completely (put IP in reset state,
cut functional and interface clocks, and so on), which
prevents us from accessing the IP's address space,
thus creating the possibility of an abort exception
when we try to access IP's address space after clocks
are off.
Cc: stable@vger.kernel.org
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.
Cc: stable@vger.kernel.org # v3.0, v3.1, v3.2, v3.3
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb can be suspended at the time some other driver wants to do ulpi
transfers using usb_phy_io_* functions, and that can cause data abort,
as it happened with isp1704_charger:
http://article.gmane.org/gmane.linux.kernel/1226122
Add pm_runtime to ulpi functions to rectify this. This also adds io_dev
to usb_phy so that pm_runtime_* functions can be used.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Control transfers with data expected from device to host will use usb_rcvctrlpipe()
for urb->pipe so for such urbs 'is_in' will be set causing control urb to fall
into the first "if" condition in musb_cleanup_urb().
Fixed by adding logic to check for non control endpoints.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Array should be freed together with event buffers, since it was
allocated dynamically.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DMA address register shouldn't be updated manually if transfer size
requires multiple packets.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Writing to TxFIFO relates only to Slave mode and leads to
TxFIFO corruption in DMA mode.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to documentation, TX FIFO_number index starts from 1.
For IN endpoint FIFO 0 we use GNPTXFSIZ register for programming
the size and memory start address.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- For Control Read transfer, the ACK handshake on an IN transaction
may be corrupted, so the device may not receive the ACK for data
stage, the complete irq will not occur at this situation.
Therefore, we need to move prime status stage from complete irq
routine to the place where the data stage has just primed, or the
host will never get ACK for status stage.
The above issue has been described at USB2.0 spec chapter 8.5.3.3.
- After adding prime status stage just after prime the data stage,
there is a potential problem when the status dTD is added before the data stage
has primed by hardware. The reason is the device's dTD descriptor has NO direction bit,
if data stage (IN) prime hasn't finished, the status stage(OUT)
dTD will be added at data stage dTD's Next dTD Pointer, so when the data stage
transfer has finished, the status dTD will be primed as IN by hardware,
then the host will never receive ACK from the device side for status stage.
- Delete below code at fsl_ep_queue:
/* Update ep0 state */
if ((ep_index(ep) == 0))
udc->ep0_state = DATA_STATE_XMIT;
the udc->ep0_state will be updated again after udc->driver->setup
finishes.
It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When runtime_pm was originally added, it was done in rather confusing
way: omap2430_musb_init() (called from musb_init_controller) would do
runtime_pm_get_sync() and musb_init_controller() itself would do
runtime_pm_put to balance it out. This is not only confusing but also
wrong if non-omap2430 glue layer is used.
This confusion resulted in commit 772aed45b6 "usb: musb: fix
pm_runtime mismatch", that removed runtime_pm_put() from
musb_init_controller as that looked unbalanced, and also happened to
fix unrelated isp1704_charger crash. However this broke runtime PM
functionality (musb is now always powered, even without gadget active).
Avoid these confusing runtime pm dependences by making
musb_init_controller() and omap2430_musb_init() do their own runtime
get/put pairs; also cover error paths. Remove unneeded runtime_pm_put
in omap2430_remove too. isp1704_charger crash that motivated
772aed45b6 will be fixed by following patch.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This change prevents runtime suspend and resume actual execution, if
omap2430 controller driver is loaded after musb-hdrc, and therefore the
controller isn't initialized properly.
The problem is reproducible with 3.1.y and 3.2 kernels.
Kernel configuration of musb:
% cat .config | egrep 'MUSB|GADGET'
CONFIG_USB_MUSB_HDRC=y
# CONFIG_USB_MUSB_TUSB6010 is not set
CONFIG_USB_MUSB_OMAP2PLUS=m
# CONFIG_USB_MUSB_AM35X is not set
CONFIG_MUSB_PIO_ONLY=y
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG is not set
# CONFIG_USB_GADGET_DEBUG_FILES is not set
# CONFIG_USB_GADGET_DEBUG_FS is not set
CONFIG_USB_GADGET_VBUS_DRAW=2
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_GADGETFS=m
# CONFIG_USB_MIDI_GADGET is not set
Fixes the following oops on module unloading:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
----8<----
[<bf162088>] (omap2430_runtime_resume+0x24/0x54 [omap2430]) from [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50)
[<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50) from [<c0031a24>] (_od_runtime_resume+0x28/0x2c)
[<c0031a24>] (_od_runtime_resume+0x28/0x2c) from [<c0306cb0>] (__rpm_callback+0x60/0xa0)
[<c0306cb0>] (__rpm_callback+0x60/0xa0) from [<c0307f2c>] (rpm_resume+0x3fc/0x6e4)
[<c0307f2c>] (rpm_resume+0x3fc/0x6e4) from [<c030851c>] (__pm_runtime_resume+0x5c/0x90)
[<c030851c>] (__pm_runtime_resume+0x5c/0x90) from [<c02fd0dc>] (__device_release_driver+0x2c/0xd0)
[<c02fd0dc>] (__device_release_driver+0x2c/0xd0) from [<c02fda18>] (driver_detach+0xe8/0xf4)
[<c02fda18>] (driver_detach+0xe8/0xf4) from [<c02fcf88>] (bus_remove_driver+0xa0/0x104)
[<c02fcf88>] (bus_remove_driver+0xa0/0x104) from [<c02fde54>] (driver_unregister+0x60/0x80)
[<c02fde54>] (driver_unregister+0x60/0x80) from [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20)
[<c02ff2d4>] (platform_driver_unregister+0x1c/0x20) from [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430])
[<bf162928>] (omap2430_exit+0x14/0x1c [omap2430]) from [<c007d8bc>] (sys_delete_module+0x1f4/0x264)
[<c007d8bc>] (sys_delete_module+0x1f4/0x264) from [<c000f000>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this default case returning an error,
thus replying with a stall, we would fail
USB30CV TD 9.11 Bad Feature test case.
Cc: stable@vger.kernel.org
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add PDMA and MDMA physical base address macros which is
require for EXYNOS5 of_dev_auxdata setup.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: changed dma channel fo mdma1]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the following warning:
warning: 'dma_dmamask' defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Also remove two warnings when CONFIG_SND_DEBUG is not set:
sound/pci/hda/patch_hdmi.c: In function ‘hdmi_intrinsic_event’:
sound/pci/hda/patch_hdmi.c:761:6: warning: unused variable ‘eldv’ [-Wunused-variable]
sound/pci/hda/patch_hdmi.c:760:6: warning: unused variable ‘pd’ [-Wunused-variable]
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch allows caching of the rindex glock. We were previously
setting the GL_NOCACHE bit when the glock was released. That forced
the rindex inode to be invalidated, which caused us to re-read
rindex at the next access. However, it caused the glock to be
unnecessarily bounced around the cluster. This patch allows
the glock to remain cached, but it still causes the rindex to be
re-read once it has been written to by gfs2_grow.
Ben and I have tested single-node gfs2_grow cases and I've tested
clustered gfs2_grow cases on my four-node cluster.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
On reset all MPU counters should be enabled in GLOBAL_CTRL MSR.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
in function nf_conntrack_init_net,when nf_conntrack_timeout_init falied,
we should call nf_conntrack_ecache_fini to do rollback.
but the current code calls nf_conntrack_timeout_fini.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It was reported that the Linux kernel sometimes logs:
klogd: [2629147.402413] kernel BUG at net / netfilter /
nf_conntrack_proto_tcp.c: 447!
klogd: [1072212.887368] kernel BUG at net / netfilter /
nf_conntrack_proto_tcp.c: 392
ipv4_get_l4proto() in nf_conntrack_l3proto_ipv4.c and tcp_error() in
nf_conntrack_proto_tcp.c should catch malformed packets, so the errors
at the indicated lines - TCP options parsing - should not happen.
However, tcp_error() relies on the "dataoff" offset to the TCP header,
calculated by ipv4_get_l4proto(). But ipv4_get_l4proto() does not check
bogus ihl values in IPv4 packets, which then can slip through tcp_error()
and get caught at the TCP options parsing routines.
The patch fixes ipv4_get_l4proto() by invalidating packets with bogus
ihl value.
The patch closes netfilter bugzilla id 771.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the commit 77b0d60c5a,
"clockevents: Leave the broadcast device in shutdown mode when not needed",
we were bailing out too quickly in tick_broadcast_switch_to_oneshot(),
with out tracking the broadcast device mode change to 'TICKDEV_MODE_ONESHOT'.
This breaks the platforms which need broadcast device oneshot services during
deep idle states. tick_broadcast_oneshot_control() thinks that it is
in periodic mode and fails to take proper decisions based on the
CLOCK_EVT_NOTIFY_BROADCAST_[ENTER, EXIT] notifications during deep
idle entry/exit.
Fix this by tracking the broadcast device mode as 'TICKDEV_MODE_ONESHOT',
before leaving the broadcast HW device in shutdown mode if there are no active
requests for the moment.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: johnstul@us.ibm.com
Link: http://lkml.kernel.org/r/1334011304.12400.81.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some r4xx chips have the wrong frev in the
DVOEncoderControl table. It should always be 1
on r4xx. Fixes modesetting on DVO on r4xx chips
with the bad frev.
Reported by twied on #radeon.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since cmdbuf->size and cmdbuf->nbox are from userspace, a large value
would overflow the allocation size, leading to out-of-bounds access.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
due to a HW limitation we have a bounce buffer for ep0
out transfers which are not aligned with MaxPacketSize.
On such case we were not increment r->actual as we should.
This patch fixes that mistake.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
To allow ep0 out transfers of upto bounce buffer size
instead of maxpacketsize, use the transfer size as multiple
of ep0 maxpacket size.
Cc: stable@vger.kernel.org
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we want to do device-initiated disconnect,
let's make sure we stop the UDC in order to
e.g. allow lower power states to be achieved by
turning off unnecessary clocks and/or stoping
PHYs.
When reconnecting, call ->udc_start() again to
make sure UDC is reinitialized.
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some architectures require that delays longer than a few
miliseconds are called through mdelay. This was triggered
on ARM randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
David pointed out, that WARN_ONCE() to report usage of an deprecated
misfeature make folks unhappy. Use printk_once() instead.
Andrew told me to stop grumbling and to remove the silly typecast
while touching the file.
Reported-by: David Rientjes <rientjes@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
handle_IRQ may briefly cause interrupts to be re-enabled during soft IRQ
processing on the exit path, leading to nested handling of VIC interrupts.
Since the current code does not re-read the VIC_IRQ_STATUS register, this
can lead to multiple invocations of the same interrupt handler and
spurious interrupts to be reported.
This patch changes the VIC interrupt dispatching code to re-read the
status register each time, avoiding duplicate invocations of the same
handler.
Acked-and-Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit 8878a539ff was done by me
to make the page fault handler retryable as well as interruptible.
Due to this commit, there is a mistake in the way in which
tsk->[maj|min]_flt counter gets incremented for VM_FAULT_ERROR:
If VM_FAULT_ERROR is returned in the fault flags by handle_mm_fault,
then either maj_flt or min_flt will get incremented. This is wrong
as in the case of a VM_FAULT_ERROR we need to be skip ahead to the
error handling code in do_page_fault.
Added a check after the call to __do_page_fault() to check for
(fault & VM_FAULT_ERROR).
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add pointer and buttonpad properties for v4 hardware.
Also, Jachiet reported that on Asus UX31, right button has no effect.
It turns out v4 has only one button, the right-button effect is
implemented with software when Windows driver is installed, or in
firmware when touchpad is in relative mode. So remove BTN_RIGHT
while at it.
Reported-by: Jachiet Louis <louis@jachiet.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acer VH40 has a Fn key toggling the touchpad on and off, but it's
implemented in system firmware, and the EC chip has to receive
reset command to activate this function. Also when this machine
wakes up after resume, psmouse_reset is necessary to bring the
touchpad back on.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
commit a546498f3b
introduced a regression on 32-bit when irq tracing
is enabled by exposing an old bug in our irq tracing
code for exception entry.
The code would save and restore some GPRs around the
calls to the C lockdep code, however, it tries to be
too smart for its own good and restores some of the
GPRs from the exception frame (as saved there on
exception entry).
However, for page faults, we do replace those GPRs with
arguments to do_page_fault before we call transfer_to_handler
and so restoring from the exception frame is plain wrong in
this case.
This was fine as long as we didn't touch the interrupt state
when taking page fault, but when I started doing it, it would
trigger the lockdep calls and the bug.
This fixes it by cleaning up that code a bit. It did create
a small stack frame for the sake of backtraces, so let's
make it a bit bigger and use it to save and restore the
stuff we care about.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the point of this error-handling code, both regions and the dma have
been allocated, so free it as done in previous and subsequent
error-handling code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the point of this error-handling code, HAVE_DSPCODEH may be undefined,
so free INITCODE and PERMCODE as done elsewhere. A jump and label are
introduced to avoid code duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit f02e8a6596 ("module: Sort exported symbols") sorts symbols
placing each of them in its own elf section. This sorting and merging
into the canonical sections are done by the linker.
Unfortunately modpost to generate Module.symvers file parses vmlinux.o
(which is not linked yet) and all modules object files (which aren't
linked yet). These aren't sanitized by the linker yet. That breaks
modpost that can't detect license properly for modules.
This patch makes modpost aware of the new exported symbols structure.
[ This above is a slightly corrected version of the explanation of the
problem, copied from commit 62a2635610 ("modpost: Fix modpost's
license checking V3"). That commit fixed the problem for module
object files, but not for vmlinux.o. This patch fixes modpost for
vmlinux.o. ]
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Alessio Igor Bogani <abogani@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The task handoff notifier leaks task_struct since it never gets freed
after the callback returns NOTIFY_OK, which means it is responsible for
doing so.
It turns out the lowmemorykiller actually doesn't need this notifier at
all. It's used to prevent unnecessary killing by waiting for a thread
to exit as a result of lowmem_shrink(), however, it's possible to do
this in the same way the kernel oom killer works by setting TIF_MEMDIE
and avoid killing if we're still waiting for it to exit.
The kernel oom killer will already automatically set TIF_MEMDIE for
threads that are attempting to allocate memory that have a fatal signal.
The thread selected by lowmem_shrink() will have such a signal after the
lowmemorykiller sends it a SIGKILL, so this won't result in an
unnecessary use of memory reserves for the thread to exit.
This has the added benefit that we don't have to rely on
CONFIG_PROFILING to prevent needlessly killing tasks.
Reported-by: Werner Landgraf <w.landgraf@ru.ru>
Cc: stable@vger.kernel.org
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1538) causes uhci_hub_status_data() to return a nonzero
value when any port is undergoing a resume transition while the root
hub is suspended. This will allow usbcore to handle races between
root-hub suspend and port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1537) adds a bit-array to ehci-hcd for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when ehci_hub_status_data() is called, the routine will return
a nonzero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1533) fixes a race between root-hub suspend and remote
wakeup. If a wakeup event occurs while a root hub is suspending, it
might not cause the suspend to fail. Although the host controller
drivers check for pending wakeup events at the start of their
bus_suspend routines, they generally do not check for wakeup events
while the routines are running.
In addition, if a wakeup event occurs any time after khubd is frozen
and before the root hub is fully suspended, it might not cause a
system sleep transition to fail. For example, the host controller
drivers do not fail root-hub suspends when a connect-change event is
pending.
To fix both these issues, this patch causes hcd_bus_suspend() to query
the controller driver's hub_status_data method after a root hub is
suspended, if the root hub is enabled for wakeup. Any pending status
changes will count as wakeup events, causing the root hub to be
resumed and the overall suspend to fail with -EBUSY.
A significant point is that not all events are reflected immediately
in the status bits. Both EHCI and UHCI controllers notify the CPU
when remote wakeup begins on a port, but the port's suspend-change
status bit doesn't get set until after the port has completed the
transition out of the suspend state, some 25 milliseconds later.
Consequently, the patch will interpret any nonzero return value from
hub_status_data as indicating a pending event, even if none of the
status bits are set in the data buffer. Follow-up patches make the
necessary changes to ehci-hcd and uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues here, one is that the device is generating
spurious very fast modem status line changes somewhere:
CTS becomes high then low 18µs later:
[121226.924373] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=6
[121226.924378] ftdi_process_packet: status=10 prev=00 diff=10
[121226.924382] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=7
(wake_up_interruptible is called)
[121226.924391] ftdi_process_packet: prev rng=0 dsr=10 dcd=0 cts=7
[121226.924394] ftdi_process_packet: status=00 prev=10 diff=10
[121226.924397] ftdi_process_packet: now rng=0 dsr=10 dcd=0 cts=8
(wake_up_interruptible is called)
This wakes up the task in TIOCMIWAIT:
[121226.924405] ftdi_ioctl: 19451 rng=0->0 dsr=10->10 dcd=0->0 cts=6->8
(wait from 20:51:46 returns and observes both changes)
Which then calls TIOCMIWAIT again:
20:51:46.400239 ioctl(3, TIOCMIWAIT, 0x20) = 0
22:11:09.441818 ioctl(3, TIOCMGET, [TIOCM_DTR|TIOCM_RTS]) = 0
22:11:09.442812 ioctl(3, TIOCMIWAIT, 0x20) = -1 EIO (Input/output error)
(the second wake_up_interruptible takes effect and an I/O error occurs)
The other issue is that TIOCMIWAIT will wait forever (unless the task is
interrupted) if the device is removed.
This change removes the -EIO return that occurs if the counts don't
appear to have changed. Multiple counts may have been processed as
one or the waiting task may have started waiting after recording the
current count.
It adds a bool to indicate that the device has been removed so that
TIOCMIWAIT doesn't wait forever, and wakes up any tasks so that they can
return -EIO.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling of TIOCMIWAIT was changed by commit 1d749f9afa
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
FTDI_STATUS_B0_MASK does not indicate the changed modem status lines,
it indicates the value of the current modem status lines. An xor is
still required to determine which lines have changed.
The count was only being incremented if the line was high. The only
reason TIOCMIWAIT still worked was because the status packet is
repeated every 1ms, so the count was always changing. The wakeup
itself still ran based on the status lines changing.
This change fixes handling of updates to the modem status lines and
allows multiple processes to use TIOCMIWAIT concurrently.
Tested with two processes waiting on different status lines being
toggled independently.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IPv6 conntrack marked invalid packets as INVALID and let the user
drop those by an explicit rule, while IPv4 conntrack dropped such
packets itself.
IPv4 conntrack is changed so that it marks INVALID packets and let
the user to drop them.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1536) fixes a bug in the USB serial core. Unloading and
reloading a serial driver while a serial device is plugged in causes
errors because of the code in usb_serial_disconnect() that tries to
make sure the port_remove method is called. With the new order of
driver registration introduced in the 3.4 kernel, this is definitely
not the right thing to do (if indeed it ever was).
The patch removes that whole section code, along with the mechanism
for keeping track of each port's registration state, which is no
longer needed. The driver core can handle all that stuff for us.
Note: This has been tested only with one or two USB serial drivers.
In theory, other drivers might still run into trouble. But if they
do, it will be the fault of the drivers, not of this patch -- that is,
the drivers will need to be fixed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right idProduct for Metrologic Bar Code Scanner
in Uni-Directional Serial Emulation mode is 0x0700.
Also rename idProduct for Bi-Directional mode to be a bit more informative.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to allow renaming network devices that have been moved
to another network namespace.
Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following gcc complain
arch/um/kernel/skas/mmu.c: In function 'uml_setup_stubs':
arch/um/kernel/skas/mmu.c:106:16: warning: unused variable 'pages' [-Wunused-variable]
Signed-Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
... rather than open-coding the 64bit versions. endian.h has those guys.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
When the rate-control indexing is incorrectly set up, mac80211 issues
a warning and returns NULL from the call to ieee80211_get_tx_rate().
When this happens, avoid a NULL pointer dereference.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the control-rate tables are not set up correctly, it makes
little sense to spam the logs, thus change the WARN_ON to WARN_ON_ONCE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before the switch to asynchronous firmware loading (mainline commit b0302ab),
it was necessary to load firmware when initializing the first of the units
in a dual-mac system. After the change, it is necessary to load firmware in
both units.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the case where we are changing from one framebuffer to
another, we need to be sure that there are no pending WAIT_FOR_EVENTs on
the pipe for the current framebuffer before switching. If we disable the
pipe, and then try to execute a WAIT_FOR_EVENT it will block
indefinitely and cause a GPU hang.
We attempted to fix this in commit 85345517fe
(drm/i915: Retire any pending operations on the old scanout when switching)
for the case of mode switching, but this leaves the condition where we
are switching off the pipe vulnerable.
There still remains the race condition were a display may be unplugged,
switched off by the core, a uevent sent to notify the DDX and the DDX
may issue a WAIT_FOR_EVENT before it processes the uevent. This window
does not exist if the pipe is only switched off in response to the
uevent. Time to make sure that is so...
Reported-by: Francis Leblanc <Francis.Leblanc-Lebeau@verint.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36515
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45413
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixup spelling in comment, noticed by Eugeni.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some configurations produce the following compiler warning:
drivers/hwmon/pmbus/pmbus_core.c: In function 'pmbus_show_boolean':
drivers/hwmon/pmbus/pmbus_core.c:752: warning: 'val' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from pmbus_get_boolean with both val and error return code (val is a
boolean and thus never negative).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47m1.c: In function 'sm_smsc47m1_init':
drivers/hwmon/smsc47m1.c:938: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47m1_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (46 bytes for x86_64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
In some configurations, BUG() does not result in an endless loop but returns
to the caller. This results in the following compiler warning:
drivers/hwmon/acpi_power_meter.c: In function 'show_str':
drivers/hwmon/acpi_power_meter.c:380: warning: 'val' may be used uninitialized in this function
Fix the warning by setting val to an empty string after BUG().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some configurations produce the following compiler warning:
drivers/hwmon/smsc47b397.c: In function 'smsc47b397_init':
drivers/hwmon/smsc47b397.c:385: warning: 'address' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from smsc47b397_find with both address and error return code (the address
is an unsigned short and thus never negative). This also reduces module size by
a few bytes (64 bytes for x86_64).
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
while we can't just use -U$(SUBARCH), we still need to kill idiotic define
(implicit -Di386=1), both for SUBARCH=i386 and SUBARCH=x86/CONFIG_64BIT=n
builds.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add UART clock quirk for the Kontron COMe-mTT10 module.
The board has previously been called nanoETXexpress-TT, therefore this
is also checked.
As suggested by Darren Hart the comparison in this patch version is
placed after the FRI2 checks to ensure it will also work with possible
upcoming changes to the FRI2 firmware.
This patch follows the patchset submitted by Darren Hart at
commit a46f5533ec.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build breakage in v3.4-rc2 that happens
with CONFIG_OMAP_MUX=y:
arch/arm/mach-omap1/mux.c:89:1: error: 'FUNC_MUX_CTRL_9' undeclared here (not in a function)
arch/arm/mach-omap1/mux.c:89:1: error: 'PULL_DWN_CTRL_2' undeclared here (not in a function)
arch/arm/mach-omap1/mux.c:93:1: error: 'FUNC_MUX_CTRL_C' undeclared here (not in a function)
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Workaround dropped notifications in the iir register. Register reads
coincident with new interrupt notifications sometimes result in this
device clearing the interrupt event without reporting it in the read
data.
The serial core already has a heuristic for determining when a device
has an untrustworthy iir register. In this case when we apriori know
that the iir is faulty use a flag (UPF_BUG_THRE) to bypass the test and
force usage of the background timer.
[stable: 3.3.x]
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Reported-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Tested-by: Nhan H Mai <nhan.h.mai@intel.com>
Tested-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 448ac154c9.
The semantic of UPF_IIR_ONCE is only guaranteed to workaround the race
condition in the kt serial's iir register if the only source of
interrupts is THRE (fifo-empty) events. An modem status event at the
wrong time can again cause an iir read to drop the 'empty' status
leading to a hang. So, revert this in preparation for using the
existing "I don't trust my iir register" workaround in the 8250 core
(UART_BUG_THRE).
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e86ff4a63c.
This tried to enforce the semantics of one interrupt per iir read of the
THRE (transmit-hold empty) status, but events from other sources
(particularly modem status) defeat this guarantee.
This change also broke 8250_pci suspend/resume support as
pciserial_resume_ports() re-runs .init() quirks, but does not run
.exit() quirks in pciserial_suspend_ports() leading to reports like:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:16.3/msi_irqs'
...and a subsequent crash. The mismatch of init/exit at suspend/resume
seems like a bug in its own right.
[stable: 3.3.x]
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Sudhakar Mamillapalli <sudhakar@fb.com>
Reported-by: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the omap serial driver is built as a module, we must
not allow the console driver to be selected, because consoles
can not be loadable modules.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix omission initialize ulcon in s3c24xx_serial_resetport(),
reset port function in drivers/tty/serial/samsung.c. It has
been happened from commit 0dfb3b41("serial: samsung: merge
all SoC specific port reset functions")
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable <stable@vger.kernel.org> [3.3]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A prototype for kmsg records instead of a byte-stream buffer revealed
a couple of missing printk(KERN_CONT ...) uses. Subsequent calls produce
one record per printk() call, while all should have ended up in a single
record.
Instead of:
ACPI: (supports S0 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
hpet0: at MMIO 0xfed00000, IRQs 2 , 8 , 0
It prints:
ACPI: (supports S0
S5
)
ACPI: PCI Interrupt Link [LNKA] (IRQs
5
*10
11
)
hpet0: at MMIO 0xfed00000, IRQs
2
, 8
, 0
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On our custom board, we are using RS485 in half-duplex mode on an AT91SAM9G45.
SER_RS485_RX_DURING_TX is not set as we do not want to receive the data we
transmit (our transceiver will receive transmitted data).
Although the current driver attempts to disable and enable the receiver at the
appropriate points, incoming data is still loaded into the receive register
causing our code to receive the very last byte that was sent once the receiver
is enabled.
I ran this by Atmel support and they wrote: "The issue comes from the fact
that you disable the PDC/DMA Reception and not the USART Reception channel. In
your case, the[n] you will still receive data into the USART_RHR register, and
maybe you [h]ave the overrun flag set. So please disable the USART reception
channel."
The following patch should force the driver to enable/disable the receiver via
RXEN/RXDIS fields of the USART control register. It fixed the issue I was
having.
Signed-off-by: Gabe Siftar <gabe.siftar@getingeusa.com>
[nicolas.ferre@atmel.com: slightly modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "TTY buffer in tty_port" patchset introduced an opencoded
debug message in the Gigaset tty device if_close() function.
Change it to use the gig_dbg() macro like everywhere else in
the driver.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch does the following
- The pm_runtime_disable is called in the remove not in the error
case of probe.The patch calls the pm_runtime_disable in the error
case.
- Calls pm_runtime_put in the error case.
- The up is not freed in the error path. Fix the memory leak by using
devm_* so that the memory need not be freed in the driver.
- Also the iounmap is not called fix the same by calling using devm_ioremap.
- Make the name of the error tags more meaningful.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may hit this in xt_LOG:
net/built-in.o:xt_LOG.c:function dump_ipv6_packet:
error: undefined reference to 'ip6t_ext_hdr'
happens with these config options:
CONFIG_NETFILTER_XT_TARGET_LOG=y
CONFIG_IP6_NF_IPTABLES=m
ip6t_ext_hdr is fairly small and it is called in the packet path.
Make it static inline.
Reported-by: Simon Kirby <sim@netnation.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For a picked up connection, the window win is scaled twice: one is by the
initialization code, and the other is by the sender updating code.
I use the temporary variable swin instead of modifying the variable win.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The driver frees the clock samples buffer before stopping the video
buffers queue. If a DQBUF call arrives in-between,
uvc_video_clock_update() will be called with a NULL clock samples
buffer, leading to a crash. This occurs very frequently when using the
webcam with the flash browser plugin.
Move clock initialization/cleanup to uvc_video_enable() in order to free
the clock samples buffer after the queue is stopped. Make sure the clock
is reset at resume time to avoid miscalculating timestamps.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Sunday, April 01, 2012 21:09:34 Tracey Dent wrote:
> radio-maxiradio depends on SND_FM801_TEA575X_BOOL to build or will
> result in an build error such as:
>
> Kernel: arch/x86/boot/bzImage is ready (#1)
> ERROR: "snd_tea575x_init" [drivers/media/radio/radio-maxiradio.ko] undefined!
> ERROR: "snd_tea575x_exit" [drivers/media/radio/radio-maxiradio.ko] undefined!
> WARNING: modpost: Found 6 section mismatch(es).
> To see full details build your kernel with:
> 'make CONFIG_DEBUG_SECTION_MISMATCH=y'
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Select CONFIG_SND_TEA575X to fixes problem and enable
> the driver to be built as desired.
>
> v2:
> instead of selecting CONFIG_SND_FM801_TEA575X_BOOL, select
> CONFIG_SND_TEA575X, which in turns selects CONFIG_SND_FM801_TEA575X_BOOL
> and any other dependencies for it to build.
No, this is the correct patch:
RADIO_MAXIRADIO should be treated just like RADIO_SF16FMR2, I just didn't
realize at the time that it had to be added as a SND_TEA575X dependency.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
has_get_frontend() should return a boolean, not a pointer.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some systems the device does not respond or give obscure values after cold,
warm or firmware reboot.
This patch retries to get chip version and type 5 times. If it
fails it applies chip version 0x1 and type 0x9135.
This patch does not fix warm cycle problems from other operating
systems and indeed the reverse applies. Users should power off cold boot.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When I converted ivtv to the new decoder API I introduced a regression in the
support of the old channel select API.
Thanks to Martin Dauskardt for reporting this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit e399ce77e6 has broken the DVB ABI for xine:
The problem is that xine is expecting every event after a successful
FE_SET_FRONTEND ioctl to have a non-zero frequency parameter, regardless
of whether the tuning process has LOCKed yet. What used to happen is
that the events inherited the initial tuning parameters from the
FE_SET_FRONTEND call. However, the fepriv->parameters_out struct is now
not initialised until the status contains the FE_HAS_LOCK bit.
You might argue that this behaviour is intentional, except that if an
application other than xine uses the DVB adapter and manages to set the
parameters_out.frequency field to something other than zero, then xine
no longer has any problems until either the adapter is replugged or the
kernel modules reloaded. This can only mean that the
fepriv->parameters_out struct still contains the (stale) tuning
information from the previous application.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Cc: stable@kernel.org # for kernel version 3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Access to global talitos registers must be protected for the case when
affinities are configured such that primary and secondary talitos irqs
run on different cpus.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Dump tagmap on failure, instead of individual tags.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* If a ncq command time out and a non-ncq command is active, skip restart port
* Queue(pause) ncq commands during operations spanning more than one non-ncq commands - secure erase, download microcode
* When a non-ncq command is active, allow incoming non-ncq commands to wait instead of failing back
* Changed timeout for download microcode and smart commands
* If the device in write protect mode, fail all writes (do not send to device)
* Set maximum retries to 2
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shortened macros used to represent mtip_port->flags and dd->dd_flag
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Handle the interrupt completion of polled internal commands
* Do not check remove pending flag for standby command
* On rebuild failure,
- set corresponding bit dd_flag
- do not send standby command
* Free ida index in remove path
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Add support for detecting the following device status
- write protect
- over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Moved setting completion time into mtip_issue_ncq_command()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Merged the following flags into one variable 'dd_flag':
* drv_cleanup_done
* resumeflag
* Added the following flags into 'dd_flag'
* remove pending
* init done
* Removed 'ftlrebuildflag' (similar flag is already part of mti_port->flags)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
d_genocide() does _not_ evict dentries; it just removes extra ref
pinning each of those. Normally it's followed by shrinking the
tree (it's done just before generic_shutdown_super() by kill_litter_super()),
but in case of simple_fill_super() nothing of that kind will follow.
Just do shrink_dcache_parent() manually.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch is omitted in v2 patch of Jaecheol Lee.
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_clkdiv':
drivers/cpufreq/exynos5250-cpufreq.c:144: error: 'EXYNOS5_CLKDIV_STATCPU0' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:144: error: (Each undeclared identifier is reported only once
drivers/cpufreq/exynos5250-cpufreq.c:144: error: for each function it appears in.)
drivers/cpufreq/exynos5250-cpufreq.c:150: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:152: error: 'EXYNOS5_CLKDIV_STATCPU1' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'set_apll':
drivers/cpufreq/exynos5250-cpufreq.c:166: error: 'EXYNOS5_CLKMUX_STATCPU' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c:173: error: 'EXYNOS5_APLL_LOCK' undeclared (first use in this function)
drivers/cpufreq/exynos5250-cpufreq.c: In function 'exynos5250_cpufreq_init':
drivers/cpufreq/exynos5250-cpufreq.c:312: error: 'EXYNOS5_CLKDIV_CPU1' undeclared (first use in this function)
Cc: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This fixes following build error when sound support is selected
on EXYNOS4 platform.
sound/soc/samsung/idma.c: In function ‘idma_close’:
sound/soc/samsung/idma.c:327:11: error: ‘IRQ_I2S0’ undeclared (first use in this function)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit 719a4240("mfd: Remove unused LDO supply field
from WM8994 pdata"), the LDO supply field should be removed from
the initializer.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kyrofb is completely broken on x86_64 because the registers are defined as
unsigned long. Change them to u32 to make the driver work.
Tested with Hercules 3D Prophet 4000XT.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Pull security layer fixlet from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
sysctl: fix write access to dmesg_restrict/kptr_restrict
ASoC: fixes for 3.4
A bunch of driver-specific fixes and one generic fix for the new support
for platform DAPM contexts - we were picking the wrong default for the
idle_bias_off setting which was meaning we weren't actually achieving
any useful runtime PM on platform devices.
name pins consistently (MIC1/LINE1/HP-OUT/CD) on all controls
affecting those pins.
remove duplicate SET_AMP_GAIN_MUTE to 0x17/index 0 and 0x17/index 1
really select MIC1, not Mixer out for recording
"Mixer out" for recording is not a "pin", adjust comment
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CX20549 (ctx5045) doesn't accept data on index 1 for output pins,
as shown in the following hda-var transaction:
$ hda-verb /dev/snd/hwC0D0 0x10 set_amp_gain 0xb126
nid = 0x10, verb = 0x300, param = 0xb126
value = 0x0
$ hda-verb /dev/snd/hwC0D0 0x10 get_amp_gain 0x8001
nid = 0x10, verb = 0xb00, param = 0x8001
value = 0x0
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ID used for detection of the BenQ R55E actually identifies the
Quanta TW3 ODM design, which is also used for the Gigabyte W551 laptop
series. Schematics on the internet clearly indicate that the "Port C"
(analog input connected to record source #4 and mixer input #4) is
unconnected.
Playing an audio CD through analog playback (using cdplay from cdtools)
produces no sound, even with the mixer input labelled "CD" enabled, and
the volume control in the CD drive set to maximum. This indicates the
connection is really not present.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "input converter" widget of the CX20459 has only one input amplifier,
expose that one as "Capture Volume/Capture Switch". The actual record
source selection is already exposed through the separately installed
input mux.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CX20549 has only one single input amp on it's input converter
widget. Fix printing of values in the codec file in /proc/asound.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Pull target fixes from Nicholas Bellinger:
"Pull two tcm_fc fabric related fixes for -rc2:
Note that both have been CC'ed to stable, and patch #1 is the
important one that addresses a memory corruption bug related to FC
exchange timeouts + command abort.
Thanks again to MDR for tracking down this issue!"
* '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Do not free tpg structure during wq allocation failure
tcm_fc: Add abort flag for gracefully handling exchange timeout
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
Pull MMC fixes from Chris Ball:
- Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
- Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
- Fix module reloading on omap_hsmmc.
- Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
* tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (28 commits)
mmc: use really long write timeout to deal with crappy cards
mmc: sdhci-dove: Fix compile error by including module.h
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Revert "mmc: sdhci-pci: Add MSI support"
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
mmc: core: fix power class selection
mmc: omap_hsmmc: fix module re-insertion
mmc: omap_hsmmc: convert to module_platform_driver
mmc: omap_hsmmc: make it behave well as a module
mmc: omap_hsmmc: trivial cleanups
mmc: omap_hsmmc: context save after enabling runtime pm
mmc: omap_hsmmc: use runtime put sync in probe error patch
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
mmc: bus: print bus speed mode of UHS-I card
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
mmc: sh_mmcif: Simplify calculation of mmc->f_min
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc: sh_mmcif: double clock speed
mmc: block: Remove use of mmc_blk_set_blksize
mmc: atmel-mci: add support for odd clock dividers
...
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1534c) updates the documentation for usb_unlink_urb and
related functions. It explains that the caller must prevent the URB
being unlinked from getting deallocated while the unlink is taking
place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com>
CC: Ming Lei <tom.leiming@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The doc says that the data
| 55534243 5e000000 00000000 00000600 00000000 00000000 00000000 000000
is the SCSI command 0x5e. According to the usbmon source, it dumps one
byte after the other. The first 4 bytes are US_BULK_CB_SIGN which is
correct. After that we see the TAG which is 0x5e. The cdb is 0x00 in
this example.
In order to correct this, I change the example to a READ_10 command
which is 0x28 so it is not just a zero somewhere in the stream.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53c6bc24fd (usb: Don't make
USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.) Removed the
dependency of the USB_ARCH_HAS_* symbols on USB_SUPPORT. However the
resulting Kconfig somehow caused many of the USB configuration items
to appear under the top level devices menu.
To fix this we reunite the 'menuconfig USB_SUPPORT' with the 'if
USB_SUPPORT', and the config items magically go back to their desired
location.
Reported-by: Julian Wollrath <jwollrath@web.de>
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Reported-by: Rupesh Gujare <rgujare@ozmodevices.com>
Reported-by: Feng King <ronyjin@tencent.com>
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a NULL pointer dereference panic in cpuidle_play_dead() during
CPU off-lining when no cpuidle driver is registered. A cpuidle
driver may be registered at boot-time based on CPU type. This patch
allows an off-lined CPU to enter HLT-based idle in this condition.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Cc: Boris Ostrovsky <boris.ostrovsky@amd.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We do auto block plug flush to reduce latency, the threshold is 16
requests. This works well if the task is accessing one or two drives.
The problem is if the task is accessing a raid 0 device and the raid
disk number is big, say 8 or 16, 16/8 = 2 or 16/16=1, we will have
heavy lock contention.
This patch makes the threshold per-disk based. The latency should be
still ok accessing one or two drives. The setup with application
accessing a lot of drives in the meantime uaually is big machine,
avoiding lock contention is more important, because any contention
will actually increase latency.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is an extra and unnecessary call to smp_processor_id()
in cpu_bringup(). Remove it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The above mentioned patch checks the IOAPIC and if it contains
-1, then it unmaps said IOAPIC. But under Xen we get this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
IP: [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
PGD 0
Oops: 0002 [#1] SMP
CPU 0
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.2.10-3.fc16.x86_64 #1 Dell Inc. Inspiron
1525 /0U990C
RIP: e030:[<ffffffff8134e51f>] [<ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
RSP: e02b: ffff8800d42cbb70 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000000ffffffef RCX: 0000000000000001
RDX: 0000000000000040 RSI: 00000000ffffffef RDI: 0000000000000001
RBP: ffff8800d42cbb80 R08: ffff8800d6400000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffef
R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000010
FS: 0000000000000000(0000) GS:ffff8800df5fe000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0:000000008005003b
CR2: 0000000000000040 CR3: 0000000001a05000 CR4: 0000000000002660
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper/0 (pid: 1, threadinfo ffff8800d42ca000, task ffff8800d42d0000)
Stack:
00000000ffffffef 0000000000000010 ffff8800d42cbbe0 ffffffff8134f157
ffffffff8100a9b2 ffffffff8182ffd1 00000000000000a0 00000000829e7384
0000000000000002 0000000000000010 00000000ffffffff 0000000000000000
Call Trace:
[<ffffffff8134f157>] xen_bind_pirq_gsi_to_irq+0x87/0x230
[<ffffffff8100a9b2>] ? check_events+0x12+0x20
[<ffffffff814bab42>] xen_register_pirq+0x82/0xe0
[<ffffffff814bac1a>] xen_register_gsi.part.2+0x4a/0xd0
[<ffffffff814bacc0>] acpi_register_gsi_xen+0x20/0x30
[<ffffffff8103036f>] acpi_register_gsi+0xf/0x20
[<ffffffff8131abdb>] acpi_pci_irq_enable+0x12e/0x202
[<ffffffff814bc849>] pcibios_enable_device+0x39/0x40
[<ffffffff812dc7ab>] do_pci_enable_device+0x4b/0x70
[<ffffffff812dc878>] __pci_enable_device_flags+0xa8/0xf0
[<ffffffff812dc8d3>] pci_enable_device+0x13/0x20
The reason we are dying is b/c the call acpi_get_override_irq() is used,
which returns the polarity and trigger for the IRQs. That function calls
mp_find_ioapics to get the 'struct ioapic' structure - which along with the
mp_irq[x] is used to figure out the default values and the polarity/trigger
overrides. Since the mp_find_ioapics now returns -1 [b/c the IOAPIC is filled
with 0xffffffff], the acpi_get_override_irq() stops trying to lookup in the
mp_irq[x] the proper INT_SRV_OVR and we can't install the SCI interrupt.
The proper fix for this is going in v3.5 and adds an x86_io_apic_ops
struct so that platforms can override it. But for v3.4 lets carry this
work-around. This patch does that by providing a slightly different variant
of the fake IOAPIC entries.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
commit b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Commit d4a2eca "ASoC: Tegra I2S: Remove dependency on pdev->id" changed
the prototype of tegra_i2s_debug_add, but didn't update the dummy inline
used when !CONFIG_DEBUG_FS. Fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org> # 3.3
Fix tick_nohz_restart() to not use a stale ktime_t "now" value when
calling tick_do_update_jiffies64(now).
If we reach this point in the loop it means that we crossed a tick
boundary since we grabbed the "now" timestamp, so at this point "now"
refers to a time in the old jiffy, so using the old value for "now" is
incorrect, and is likely to give us a stale jiffies value.
In particular, the first time through the loop the
tick_do_update_jiffies64(now) call is always a no-op, since the
caller, tick_nohz_restart_sched_tick(), will have already called
tick_do_update_jiffies64(now) with that "now" value.
Note that tick_nohz_stop_sched_tick() already uses the correct
approach: when we notice we cross a jiffy boundary, grab a new
timestamp with ktime_get(), and *then* update jiffies.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Ben Segall <bsegall@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1332875377-23014-1-git-send-email-ncardwell@google.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc1f8bf68b ('netdev: change
transmit to limited range type') changed the required return type and
9a1654ba0b ('net: Optimize
hard_start_xmit() return checking') changed the valid numerical
return values.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08baf56108 ('net:
txq_trans_update() helper') made it unnecessary for most drivers to
set net_device::trans_start (or netdev_queue::trans_start).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits d314774cf2 ('netdev: network
device operations infrastructure') and
008298231a ('netdev: add more functions
to netdevice ops') moved and renamed net device operation pointers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits e308a5d806 ('netdev: Add
netdev->addr_list_lock protection.') and
e8a0464cc9 ('netdev: Allocate multiple
queues for TX.') introduced more fine-grained locks.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348eef ('[NET]: Make NAPI
polling independent of struct net_device objects.') removed the
automatic disabling of NAPI polling by dev_close(), and drivers
must now do this themselves.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e52ac3398c ('net: Use device
model to get driver name in skb_gso_segment()') removed the only
in-tree caller of ethtool ops that doesn't hold the RTNL lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Pull a few blackfin compile fixes from Bob Liu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: update defconfig for bf527-ezkit
blackfin: gpio: fix compile error if !CONFIG_GPIOLIB
blackfin: fix L1 data A overflow link issue
To fix compile error:
drivers/usb/musb/blackfin.h:51:3: error: #error "Please use PIO mode in MUSB
driver on bf52x chip v0.0 and v0.1"
make[4]: *** [drivers/usb/musb/blackfin.o] Error 1
Signed-off-by: Bob Liu <lliubbo@gmail.com>
This patch fix below compile error:
"bfin-uclinux-ld: L1 data A overflow!"
It is due to the recent lib/gen_crc32table.c change:
46c5801eaf
crc32: bolt on crc32c
it added 8KiB more data to __cacheline_aligned which cause blackfin L1 data
cache overflow.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Pull an APM fix from Jiri Kosina:
"One deadlock/race fix from Niel that got introduced when we were
moving away from freezer_*_count() to wait_event_freezable()."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
APM: fix deadlock in APM_IOC_SUSPEND ioctl
Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.
This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:
* With certain SD cards timeouts like the following have been seen
due to an improper calculation of the dto value:
mmcblk0: error -110 transferring data, sector 4126233, nr 8,
card status 0xc00
* By removing the dto calculation and setting the timeout value
to the maximum specified by the SD card specification part A2
section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
relevant ones are:
* http://talk.maemo.org/showthread.php?p=1000707#post1000707
* http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a compile error in drivers/mmc/host/sdhci-dove.c
by including the linux/module.h file.
Signed-off-by: Alf Høgemark <alf@i100.no>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit e6039832be.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.
According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.
Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
OMAP4 and OMAP3 HSMMC IP registers differ by 0x100 offset.
Adding the offset to platform_device resource structure
increments the start address for every insmod operation.
MMC command fails on re-insertion as module due to incorrect register
base. Fix this by updating the ioremap base address only.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This will delete some boilerplate code, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If we put probe() on __init section, that will never work for multiple
module insertions/removals.
In order to make it work properly, move probe to __devinit section and
use platform_driver_register() instead of platform_driver_probe().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A bunch of non-functional cleanups to the omap_hsmmc driver.
It basically decreases indentation level, drop unneded dereferences
and drop unneded accesses to the platform_device structure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call context save api after enabling runtime pm to make sure that
register access in context save api happens with clk enabled.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Neil Brown reports that commit 35cd133c
PM: Run the driver callback directly if the subsystem one is not there
breaks suspend for his libertas wifi, because SDIO has a protocol
where the suspend method can return -ENOSYS and this means "There is
no point in suspending, just turn me off". Moreover, the suspend
methods provided by SDIO drivers are not supposed to be called by
the PM core or bus-level suspend routines (which aren't presend for
SDIO). Instead, when the SDIO core gets to suspend the device's
ancestor, it calls the device driver's suspend function, catches the
ENOSYS, and turns the device off.
The commit above breaks the SDIO core's assumption that the device
drivers' callbacks won't be executed if it doesn't provide any
bus-level callbacks. If fact, however, this assumption has never
been really satisfied, because device class or device type suspend
might very well use the driver's callback even without that commit.
The simplest way to address this problem is to make the SDIO core
tell the PM core to ignore driver callbacks, for example by providing
no-operation suspend/resume callbacks at the bus level for it,
which is implemented by this change.
Reported-and-tested-by: Neil Brown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
[stable: please apply to 3.3-stable only]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MSI on my O2Micro OZ600 SD card reader is broken. This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no need to tune mmc->f_min to a value near 400kHz as the MMC core
begins testing frequencies at 400kHz regardless of the value of mmc->f_min.
As suggested by Guennadi Liakhovetski.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc->f_max should be half of the bus clock.
And now that mmc->f_max is not equal to the bus clock the
latter should be used directly to calculate mmc->f_min.
Cc: Magnus Damm <magnus.damm@gmail.com>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Correct an off-by one error when calculating the clock divisor in cases
where the host clock is a power of two of the target clock. Previously the
divisor was one greater than the correct value in these cases leading to
the clock being set at half the desired speed.
Thanks to Guennadi Liakhovetski for working with me on the logic for this
change.
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since most of the work is already done by the core we just need to add
runtime suspend methods and tell the PM core that runtime PM is enabled
for this device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
The call to platform_get_resource was moved just to make it closer to the
place where its result it used.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the sdhci-s3c driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_width member in platform data can be used to derive the mmc bus transfer
width that can be supported by the controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI controllers on Exynos4 do not include the sdclk divider as per the
sdhci controller specification. This case can be represented using the
sdhci quirk SDHCI_QUIRK_NONSTANDARD_CLOCK instead of using an additional
enum type definition 'clk_types'.
Hence, usage of clk_type member in platform data is removed and the sdhci
quirk is used. In addition to that, since this qurik is SoC specific,
driver data is introduced to represent controllers on SoC's that require
this quirk.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Marvell has agreed to do maintenance on the sky2 driver.
* Add the developer to the maintainers file
* Remove the old reference to the long gone (sk98lin) driver
* Rearrange to fit current topic organization
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2f53384424 (tcp: allow splice() to build full TSO packets) added
a regression for splice() calls using SPLICE_F_MORE.
We need to call tcp_flush() at the end of the last page processed in
tcp_sendpages(), or else transmits can be deferred and future sends
stall.
Add a new internal flag, MSG_SENDPAGE_NOTLAST, acting like MSG_MORE, but
with different semantic.
For all sendpage() providers, its a transparent change. Only
sock_sendpage() and tcp_sendpages() can differentiate the two different
flags provided by pipe_to_sendpage()
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail>com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This routine was checking only if the provided address was after
sym->end, not if it was before sym->start.
Fix that by checking for both and return in both cases -ERANGE, so that
tools can communicate this to the user properly, or if they chose so, to
abort.
This problem was reported previously but the fixes involved either doing
what was being done for the > end case, i.e. silently drop the sample,
returning 0, or aborting at this function, which is in a lib (or better,
is slated to be at some point) and shouldn't abort.
The 'report' tool already checks this value and uses pr_debug to warn
the user.
This patch makes the 'top' tool check it too and warn once per map where
such range problem takes place.
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Sorin Dumitru <dumitru.sorin87@gmail.com>
Reported-by: Stephane Eranian <eranian@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-lw8gs7p9i9nhldilo82tzpne@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
This is the fallout from adding memcpy alignment workaround for certain
IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align
ops.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Although mem_cgroup_uncharge_swap has an empty placeholder for
!CONFIG_CGROUP_MEM_RES_CTLR_SWAP the definition is placed in the
CONFIG_SWAP ifdef block so we are missing the same definition for
!CONFIG_SWAP which implies !CONFIG_CGROUP_MEM_RES_CTLR_SWAP.
This has not been an issue before, because mem_cgroup_uncharge_swap was
not called from !CONFIG_SWAP context. But Hugh Dickins has a cleanup
patch to call __mem_cgroup_commit_charge_swapin which is defined also
for !CONFIG_SWAP.
Let's move both the empty definition and declaration outside of the
CONFIG_SWAP block to avoid the following compilation error:
mm/memcontrol.c: In function '__mem_cgroup_commit_charge_swapin':
mm/memcontrol.c:2837: error: implicit declaration of function 'mem_cgroup_uncharge_swap'
if CONFIG_SWAP is disabled.
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS. It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.
This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described in e6fa16ab9c ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described in e6fa16ab9c ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check for shared signals we're about to block.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
debugfs and a few other drivers use an open-coded version of
simple_open() to pass a pointer from the file to the read/write file
ops. Add support for this simple case to libfs so that we can remove
the many duplicate copies of this simple function.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was introduced by d1d5e05ffd ("hugetlbfs: return error code when
initializing module") but as Al pointed out, is a bad idea.
Quoted comments from Al:
"Note that unregister_filesystem() in module init is *always* wrong;
it's not an issue here (it's done too early to care about and
realistically the box is not going anywhere - it'll panic when attempt
to exec /sbin/init fails, if not earlier), but it's a damn bad
example.
Consider a normal fs module. Somebody loads it and in parallel with
that we get a mount attempt on that fs type. It comes between
register and failure exits that causes unregister; at that point we
are screwed since grabbing a reference to module as done by mount is
enough to prevent exit, but not to prevent the failure of init. As
the result, module will get freed when init fails, mounted fs of that
type be damned."
So remove it.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allocation can be as large as 64k. As David points out, "falling
back to vmalloc here is much better solution than failing to retreive
the attribute - it will work no matter how fragmented memory gets. That
means we don't get incomplete backups occurring after days or months of
uptime and successful backups".
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change send_sig_all() to use do_send_sig_info(SEND_SIG_FORCED) instead
of force_sig(SIGKILL). With the recent changes we do not need force_ to
kill the CLONE_NEWPID tasks.
And this is more correct. force_sig() can race with the exiting thread,
while do_send_sig_info(group => true) kill the whole process.
Some more notes from Oleg Nesterov:
> Just one note. This change makes no difference for sysrq_handle_kill().
> But it obviously changes the behaviour sysrq_handle_term(). I think
> this is fine, if you want to really kill the task which blocks/ignores
> SIGTERM you can use sysrq_handle_kill().
>
> Even ignoring the reasons why force_sig() is simply wrong here,
> force_sig(SIGTERM) looks strange. The task won't be killed if it has
> a handler, but SIG_IGN can't help. However if it has the handler
> but blocks SIGTERM temporary (this is very common) it will be killed.
Also,
> force_sig() can't kill the process if the main thread has already
> exited. IOW, it is trivial to create the process which can't be
> killed by sysrq.
So, this patch fixes the issue.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The proc_parse_options() call from proc_mount() runs only once at boot
time. So on any later mount attempt, any mount options are ignored
because ->s_root is already initialized.
As a consequence, "mount -o <options>" will ignore the options. The
only way to change mount options is "mount -o remount,<options>".
To fix this, parse the mount options unconditionally.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silicon errata where when RAID and legacy descriptors are mixed, the legacy
(memcpy and friends) operation must have alignment of 64 bytes to avoid
hanging. This effects Intel Xeon C55xx, C35xx, E5-2600.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The alloc order can be up to 16 and 1 << 16 will over flow the 16bit
integer. Change the appropriate variables to 16bit to avoid overflow.
Reported-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If there's an event with no samples in data file, the perf report
command can segfault after entering the event details menu.
Following steps reproduce the issue:
# ./perf record -e syscalls:sys_enter_kexec_load,syscalls:sys_enter_mmap ls
# ./perf report
# enter '0 syscalls:sys_enter_kexec_load' menu
# pres ENTER twice
Above steps are valid assuming ls wont run kexec.. ;)
The check for sellection to be NULL is missing. The fix makes sure it's
being check. Above steps now endup with menu being displayed allowing
'Exit' as the only option.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333570898-10505-2-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a process exec()'s, all the maps are retired, but we keep the hist
entries around which hold references to those outdated maps.
If the same library gets mapped in for which we have hist entries, a new
map will be created. But when we take a perf entry hit within that map,
we'll find the existing hist entry with the older map.
This causes symbol translations to be done incorrectly. For example,
the perf entry processing will lookup the correct uptodate map entry and
use that to calculate the symbol and DSO relative address. But later
when we update the histogram we'll translate the address using the
outdated map file instead leading to conditions such as out-of-range
offsets in symbol__inc_addr_samples().
Therefore, update the map of the hist_entry dynamically at lookup/
creation time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/20120327.031418.1220315351537060808.davem@davemloft.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ASoC core currently defaults to using STANDBY rather than OFF for
idle ASoC platform devices, which causes a permanent pm_runtime_get() on
them. This keeps the device active unnecessarily. This can be especially
problematic when the ASoC platform device and DAI device are the same
device.
The distinction between OFF and STANDBY is likely not relevant for ASoC
platform drivers, since they aren't analog devices. So, solve this issue
by hard-coding idle_bias_off = 1 for all ASoC platform devices. If this
turns out to be a problem, this value could be sourced from the
snd_soc_platform_driver, similarly to soc_probe_codec().
Note: Prior to this change, this caused a large (10) runtime_active count
for the Tegra I2S controller even when not in use, and a leak in that
value as streams were started and stopped. This change probably hides a
bug.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With commit c334bc1 (ARM: make mach/io.h include optional), PCMCIA was
broken. PCMCIA depends on __io() returning a valid i/o address, and most
ARM platforms require IO_SPACE_LIMIT be set to 0xffffffff for PCMCIA. This
needs a better fix with a fixed i/o address mapping, but for now we just
restore things to the previous behavior.
This fixes at91, omap1, pxa and sa11xx. pxa needs io.h if PCI is enabled,
but PCMCIA is not. sa11xx already has IO_SPACE_LIMIT set to 0xffffffff,
so it doesn't need an io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Joachim Eastwood <joachim.eastwood@jotron.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com> (pxa270)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
To ensure that old user space versions do not accidentally pick up and
try to use the management channel, use a different channel number.
Reported-by: Keith Packard <keithp@keithp.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
From Tony Lindgren:
Note that this also contains a set of fixes that are not regressions
or oopses to properly deal with the smsc911x regulator issue.
Basically the regulators must be per board file as the regulators
can also come from drivers, such as twl4030. So it's best to dumb
down gpmc-smsc911x.c to not even care about the regulators.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: fix section mismatches in usb-host.c
ARM: OMAP2+: Fix omap2+ build error
ARM: OMAP2+: smsc911x: Add fixed board regulators
ARM: OMAP2+: smsc911x: Remove regulator support from gmpc-smsc911x
ARM: OMAP2+: smsc911x: Remove unused rate calculation
ARM: OMAP2+ smsc911x: Fix possible stale smsc911x flags
ARM: OMAP2+: smsc911x: Remove odd gpmc_cfg/board_data redirection
ARM: OMAP3+: fix oops triggered in omap_prcm_register_chain_handler(v1)
ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present
arm: omap3: pm34xx.c: Replace printk() with appropriate pr_*()
arm: omap3: pm34xx.c: Fix omap3_pm_init() error out paths
ARM: OMAP4: Workaround the OCP synchronisation issue with 32K synctimer.
ARM: OMAP4: prm: fix interrupt register offsets
ARM: OMAP: hwmod: Use sysc_fields->srst_shift and get rid of hardcoded SYSC_TYPE2_SOFTRESET_MASK
* 'for-3.4/fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain
"halt()" function. Use safe_halt() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Five fixes for bugs that have crept in to the powerpc KVM implementations.
These are all small simple patches that only affect arch/powerpc/kvm.
They come from the series that Alex Graf put together but which was too
late for the 3.4 merge window.
* tag 'powerpc-fixes' of git://github.com/paulusmack/linux:
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Signed-off-by: Avi Kivity <avi@redhat.com>
vmx_set_cr0 is called from vcpu run context, therefore it expects
kvm->srcu to be held (for setting up the real-mode TSS).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fixes the following warning:
warning: 'dma_dmamask' defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Before commit de47725421 ("include: replace
linux/module.h with "struct module" wherever possible") <linux/module.h> was
implicitly included through <linux/platform_device.h> -> <linux/device.h>.
Signed-off-by: Michał Wróbel <michal.wrobel@flytronic.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current code only increments the upper 64 bits of the SHA-512 byte
counter when the number of bytes hashed happens to hit 2^64 exactly.
This patch increments the upper 64 bits whenever the lower 64 bits
overflows.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the call from gfs2_blk2rgrd to function
gfs2_rindex_update and replaces it with individual calls.
The former way turned out to be too problematic.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
In the SYSC_TYPE1_XXX_MASK configuration, SYSC_XXX_SHIFT macro
is used which is not defined anywhere in the kernel.
Until now the build was going through successfully, since it
is not being used anywhere in kernel.
This bug got introduced by the commit
358f0e630d ("OMAP3: hwmod: support
to specify the offset position of various SYSCONFIG register bits.")
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_hwmod_softreset() does not seem to wait for reset status
after doing a softreset. Make it use _ocp_softreset() instead
which does this correctly.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After a softreset, make sure the sysc settings are correctly
restored.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
[paul@pwsan.com: combined post-reset SYSCONFIG reload code into the
_reset() function to avoid duplication and future mistakes]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some modules doesn't have SYSC_HAS_ENAWAKEUP bit available (ex: usb
host uhh module) in absence of this flag
omap_hwmod_enable/disable_wakeup avoids configuring pad mux wakeup
capability.
Configure sysc if SYSC_HAS_ENAWAKEUP is available and for other cases
try enabling/disabling wakeup from mux_pad pins.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[paul@pwsan.com: updated function kerneldoc documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit bfdc0b4 adds code to restrict access to dmesg_restrict,
however, it incorrectly alters kptr_restrict rather than
dmesg_restrict.
The original patch from Richard Weinberger
(https://lkml.org/lkml/2011/3/14/362) alters dmesg_restrict as
expected, and so the patch seems to have been misapplied.
This adds the CAP_SYS_ADMIN check to both dmesg_restrict and
kptr_restrict, since both are sensitive.
Reported-by: Phillip Lougher <plougher@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
Convert array index from the loop bound to the loop index.
And remove the void type conversion to ip6_mc_del1_src() return
code, seem it is unnecessary, since ip6_mc_del1_src() does not
use __must_check similar attribute, no compiler will report the
warning when it is removed.
v2: enrich the commit header
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Fix UNC parsing on mount
Remove unnecessary check for NULL in password parser
CIFS: Fix VFS lock usage for oplocked files
Revert "CIFS: Fix VFS lock usage for oplocked files"
cifs: writing past end of struct in cifs_convert_address()
cifs: silence compiler warnings showing up with gcc-4.7.0
CIFS: Fix VFS lock usage for oplocked files
The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.
This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.
This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.
Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
Pull DMA mapping branch from Marek Szyprowski:
"Short summary for the whole series:
A few limitations have been identified in the current dma-mapping
design and its implementations for various architectures. There exist
more than one function for allocating and freeing the buffers:
currently these 3 are used dma_{alloc, free}_coherent,
dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent.
For most of the systems these calls are almost equivalent and can be
interchanged. For others, especially the truly non-coherent ones
(like ARM), the difference can be easily noticed in overall driver
performance. Sadly not all architectures provide implementations for
all of them, so the drivers might need to be adapted and cannot be
easily shared between different architectures. The provided patches
unify all these functions and hide the differences under the already
existing dma attributes concept. The thread with more references is
available here:
http://www.spinics.net/lists/linux-sh/msg09777.html
These patches are also a prerequisite for unifying DMA-mapping
implementation on ARM architecture with the common one provided by
dma_map_ops structure and extending it with IOMMU support. More
information is available in the following thread:
http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819
More works on dma-mapping framework are planned, especially in the
area of buffer sharing and managing the shared mappings (together with
the recently introduced dma_buf interface: commit d15bd7ee44
"dma-buf: Introduce dma buffer sharing mechanism").
The patches in the current set introduce a new alloc/free methods
(with support for memory attributes) in dma_map_ops structure, which
will later replace dma_alloc_coherent and dma_alloc_writecombine
functions."
People finally started piping up with support for merging this, so I'm
merging it as the last of the pending stuff from the merge window.
Looks like pohmelfs is going to wait for 3.5 and more external support
for merging.
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
common: DMA-mapping: add NON-CONSISTENT attribute
common: DMA-mapping: add WRITE_COMBINE attribute
common: dma-mapping: introduce mmap method
common: dma-mapping: remove old alloc_coherent and free_coherent methods
Hexagon: adapt for dma_map_ops changes
Unicore32: adapt for dma_map_ops changes
Microblaze: adapt for dma_map_ops changes
SH: adapt for dma_map_ops changes
Alpha: adapt for dma_map_ops changes
SPARC: adapt for dma_map_ops changes
PowerPC: adapt for dma_map_ops changes
MIPS: adapt for dma_map_ops changes
X86 & IA64: adapt for dma_map_ops changes
common: dma-mapping: introduce generic alloc() and free() methods
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to 32-bit sparc.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to 64-bit sparc.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit (bfab27a stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified from original patch from Chris.
The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.
This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.
Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7d26bb103c "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.
Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.
This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.
This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.
This leads to the new behavior that users see what they have been aware
of at compile time.
The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more power management updates from Rafael Wysocki:
- Patch series that hopefully fixes races between the freezer and
request_firmware() and request_firmware_nowait() for good, with two
cleanups from Stephen Boyd on top.
- Runtime PM fix from Alan Stern preventing tasks from getting stuck
indefinitely in the runtime PM wait queue.
- Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
* tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: add pm_qos_update_request_timeout() API
firmware_class: Move request_firmware_nowait() to workqueues
firmware_class: Reorganize fw_create_instance()
PM / Sleep: Mitigate race between the freezer and request_firmware()
PM / Sleep: Move disabling of usermode helpers to the freezer
PM / Hibernate: Disable usermode helpers right before freezing tasks
firmware_class: Do not warn that system is not ready from async loads
firmware_class: Split _request_firmware() into three functions, v2
firmware_class: Rework usermodehelper check
PM / Runtime: don't forget to wake up waitqueue on failure
Several clocks are missing clockdomains. This can cause problems with
the hwmod and power management code. Fill these in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
All DPLLs except USB are in ALWON powerdomain. Make sure the
clkdm/pwrdm for USB DPLL (l3init) is turned on before attempting
a DPLL relock. So, mark the database accordingly.
Without this fix, it was seen that DPLL relock fails while testing
relock in a loop of USB DPLL.
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b1cbdb00d ("OMAP: clockdomain: Wait for powerdomain to be ON
when using clockdomain force wakeup") was assuming that
pwrdm_state_switch() does wait for the powerdomain transition which is
not the case. The missing wait for the powerdomain transition
violates the sequence which the hardware expects, which causes power
management failures on some devices.
Fix this API by adding the pwrdm_wait_transition().
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: added some more details in the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Merge common_audit_data cleanup patches from Eric Paris.
This is really too late, but it's a long-overdue cleanup of the costly
wrapper functions for the security layer.
The "struct common_audit_data" is used all over in critical paths,
allocated and initialized on the stack. And used to be much too large,
causing not only unnecessarily big stack frames but the clearing of the
(mostly useless) data was also very visible in profiles.
As a particular example, in one microbenchmark for just doing "stat()"
over files a lot, selinux_inode_permission() used 7% of the CPU time.
That's despite the fact that it doesn't actually *do* anything: it is
just a helper wrapper function in the selinux security layer.
This patch-series shrinks "struct common_audit_data" sufficiently that
code generation for these kinds of wrapper functions is improved
noticeably, and we spend much less time just initializing data that we
will never use.
The functions still get called all the time, and it still shows up at
3.5+% in my microbenchmark, but it's quite a bit lower down the list,
and much less noticeable.
* Emailed patches from Eric Paris <eparis@redhat.com>:
lsm_audit: don't specify the audit pre/post callbacks in 'struct common_audit_data'
SELinux: do not allocate stack space for AVC data unless needed
SELinux: remove avd from slow_avc_audit()
SELinux: remove avd from selinux_audit_data
LSM: shrink the common_audit_data data union
LSM: shrink sizeof LSM specific portion of common_audit_data
Pull a single regmap fix from Mark Brown:
"A simple bug that's been lurking for a while but not terribly visible
since a high proportion of chips have no register 0 so the normal
failure is that we end up doing a bit of extra I/O."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fix register default look-up in sync
Pull regulator fixes from Mark Brown:
"A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Remove non-existent parameter from fixed-helper.c kernel doc
regulator: Fix setting new voltage in s5m8767_set_voltage
regulator: fix sysfs name collision between dummy and fixed dummy regulator
regulator: Fix deadlock on removal of regulators with supplies
regulator: Fix comments in include/linux/regulator/machine.h
regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable
regulator: Fix setting low power mode for wm831x aldo
regulator: Return microamps in wm8350_isink_get_current
regulator: wm8350: Fix the logic to choose best current limit setting
regulator: wm831x-isink: Fix the logic to choose best current limit setting
regulator: wm831x-dcdc: Fix the logic to choose best current limit setting
regulator: anatop: patching to device-tree property "reg".
regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting
regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable
regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
regulator: Fix set and get current limit for wm831x_buckv
regulator: tps6586x: Fix list minimal voltage setting for LDO0
This fixes the CPUFREQ dependency for regarding EXYNOS SoCs
such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq
driver should be built with selection of SoC arch part.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Call restore_sched_clock_state() only after %gs is initialized
x86: Use -mno-avx when available
x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility
x86: Preserve lazy irq disable semantics in fixup_irqs()
SPI chip select pins have to be checked by gpio_is_valid().
The USB host overcurrent_pin checking was missing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add comments to NAND "gpios" property to make it clearer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The DT information are filled in a pdata structure and then passed on
to the usual check code of the probe function. Thus we do not need to
redo the gpio checking and irq configuration in the DT-related code.
On the other hand, we setup GPIO direction in driver for vbus and
overcurrent. It will be useful when moving to pinctrl subsystem.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Due to an error while handling vbus_pin_active_low in ohci-at91 driver,
the specification of this property was not good in devices/board files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> [3.2+]
addruart cannot read from the physical address of the chipid
register, that will fail as soon as the mmu is turned on.
Fixing it to read from the physical or virtual address depending
on the mmu state also does not work, because there is a period
between head.S and exynos_map_io where the mmu is on, the uart
is mapped and used, but the chipid mapping is not yet present.
Fix addruart to use the ARM Main ID cp15 register to determine
if the core is Cortex A15 (EXYNOS5) or not (EXYNOS4).
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull hwmon patches from Guenter Roeck:
- Fix crash in ad7314 driver
- Add support for AMD Trinity CPUs to k10temp driver
- Fix __initdata/__initconst mixup in w83627ehf driver
- Fix runtime warnings in acpi_power_meter and max6639 drivers
- Fix build warnings in adm1031, f75375s, sht15, and gpio-fan drivers
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ad7314) Adds missing spi_dev initialization
hwmon: (k10temp) Add support for AMD Trinity CPUs
hwmon: (w83627ehf) mark const init data with __initconst instead of __initdata
hwmon: (acpi_power_meter) fix lockdep spew due to non-static lock class
hwmon: (adm1031) Fix compiler warning
hwmon: (f75375s) Fix warning message seen in some configurations
hwmon: (max6639) Convert to dev_pm_ops
hwmon: (sht15) Fix Kconfig dependencies
hwmon: (gpio-fan) Fix Kconfig dependencies
Pull MCE fixlet from Borislav Petkov:
"One fix which makes MCE decoding much more "liberal" wrt families."
* tag 'mce-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
MCE, AMD: Drop too granulary family model checks
Rename EMAC clocks to match driver expectations: both davinci_emac and
davinci_mdio drivers call clk_get(dev, NULL) so we have to provide
("davinci_emac", NULL) and ("davinci_mdio.0", NULL) clocks instead of
("davinci_emac", "emac_clk") and ("davinci_emac", "phy_clk") resp.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull assorted md fixes from Neil Brown:
- some RAID levels didn't clear up properly if md_integrity_register
failed
- a 'check' of RAID5/RAID6 doesn't actually read any data since a
recent patch - so fix that (and mark for -stable)
- a couple of other minor bugs.
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/raid1,raid10: don't compare excess byte during consistency check.
md/raid5: Fix a bug about judging if the operation is syncing or replacing
md/raid1:Remove unnecessary rcu_dereference(conf->mirrors[i].rdev).
md: Avoid OOPS when reshaping raid1 to raid0
md/raid5: fix handling of bad blocks during recovery.
md/raid1: If md_integrity_register() failed,run() must free the mem
md/raid0: If md_integrity_register() fails, raid0_run() must free the mem.
md/linear: If md_integrity_register() fails, linear_run() must free the mem.
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
Pull Sparc fixes from David Miller:
"One build regression and one serial probe regression fix on sparc."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunzilog: fix keyboard on SUN SPARCstation
sparc: pgtable_64: change include order
To fix:
In file included from kernel/exit.c:61:
arch/avr32/include/asm/mmu_context.h: In function 'enable_mmu':
arch/avr32/include/asm/mmu_context.h:135: error: implicit declaration of function 'nop'
It needs an include of the new file created in commit ae47394658
("Disintegrate asm/system.h for AVR32"), but since that file only
contains "nop", and since other arch already have precedent of putting
nop in asm/barrier.h we should just delete the new file and put nop in
barrier.h
Suggested-and-acked-by: David Howells <dhowells@redhat.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_disable_unused is invoked when CONFIG_OMAP_RESET_CLOCKS=y.
Since clk_disable_unused is called as lateinitcall, there can
be more than a few workqueues executing off secondary CPU(s).
The current code does the following:
a) checks if clk is unused
b) holds lock
c) disables clk
d) unlocks
Between (a) and (b) being executed on CPU0, It is possible to
have a driver executing on CPU1 which could do a get_sync->clk_get
(and increase the use_count) of the clock which was just about
to be disabled by clk_disable_unused.
We ensure instead that the entire list traversal is protected by
the lock allowing for parent child clock traversal which could be
potentially be done by runtime operations to be safe as well.
Reported-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit d06221c061.
It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(),
apparently because the code ends up trying to free somethng that was
never kmalloced in the first place.
BenH points out that the patch was untested and wasn't meant to go into
the upstream kernel that quickly in the first place.
Backtrace:
bios_shadow
bios_shadow_prom
nv_mask
init_io
bios_shadow
nouveau_bios_init
NVReadVgaCrtc
NVSetOwner
nouveau_card_init
nouveau_load
Reported-by: Meelis Roos <mroos@linux.ee>
Requested-by: Dave Airlie <airlied@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CLKS signal for McBSP ports can be selected from internal (PRCM) or
external (ABE_CLKS pin) source. To be able to use existing code we
need to create clock aliases consistent among OMAP2/3/4.
Based on a patch from Péter Ujfalusi <peter.ujfalusi@ti.com>;
the patch description above is his.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The commit 996bc8aebd (mmc: sh_mobile_sdhi:
do not manage PM clocks manually) modified the sh_mobile_sdhi driver to
remove the clk_enable/clk_disable. So, we need to change
the "CLKDEV_CON_ID" to "CLKDEV_DEV_ID".
If we don't change this, we will see the following error from the driver:
sh_mobile_sdhi sh_mobile_sdhi.0: timeout waiting for hardware interrupt (CMD52)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 2a9f5a4d45 "OMAP3 clock: remove unnecessary duplicate of dpll4_m2_ck,
added for 36xx" consolidated dpll4 clock structures between 34xx and 36xx,
but left 34xx CLKSEL masks for most dpll4 related clocks, which causes
clock code to not behave correctly when booting on DM3730 with higher
(36xx only) divisors set:
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:375 omap2_init_clksel_parent+0x104/0x114()
[ 0.000000] clock: dpll4_m3_ck: init parent: could not find regval 0
[ 0.000000] WARNING: at arch/arm/mach-omap2/clkt_clksel.c:194 omap2_clksel_recalc+0xd4/0xe4()
[ 0.000000] clock: Could not find fieldval 0 for clock dpll4_m3_ck parent dpll4_ck
Fix this by switching to 36xx masks, as valid divisors will be limited
by clksel_rate lists.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
If transceiver is attached to a MMC host of ES2.1 OMAP35xx, it seems
2.1.1.128 erratum doesn't apply and there is no data corruption,
probably because of different signal timing. The workaround for this
erratum disables multiblock reads, which causes dramatic loss of
performance (over 75% slower), so avoid it when transceiver is present.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 4430 ES2.0 TRM vX Table 3-744 "CM_EMU_CLKSTCTRL",
the emu_sys clockdomain data in mainline is incorrect.
The emu_sys clockdomain does not support the DISABLE_AUTO state, and
instead it supports the FORCE_WAKEUP state.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
MCA details seldom change inbetween the models of a family so don't
be too conservative and enable decoding on everything starting from
K8 onwards. Minor adjustments can come in later but most importantly,
we have some decoding infrastructure in place for upcoming models by
default.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Rather than listing every single person who works on the drivers include
the mailing list where they can all be found. Leave myself as a human
contact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On a system running glibc trunk perf doesn't build:
CC builtin-sched.o
builtin-sched.c: In function ‘get_cpu_usage_nsec_parent’: builtin-sched.c:399:16: error: storage size of ‘ru’ isn’t known builtin-sched.c:403:2: error: implicit declaration of function ‘getrusage’ [-Werror=implicit-function-declaration]
[...]
Fix it by including sys/resource.h.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120404084527.GA294@x4
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code cleanup of cifs_parse_mount_options resulted in a new bug being
introduced in the parsing of the UNC. This results in vol->UNC being
modified before vol->UNC was allocated.
Reported-by: Steve French <smfrench@gmail.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This driver was recently moved from IIO (where it worked) to hwmon (where
it doesn't.) This breakage occured because the hwmon version neglected to
correctly initialize a reference to spi_dev in its drvdata. The result is a
segfault every time the temperature is queried.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The error path misses putting the timeout object. This patch adds
new function xt_ct_tg_timeout_put() to put the timeout object.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The password parser has an unnecessary check for a NULL value which
triggers warnings in source checking tools. The code contains artifacts
from the old parsing code which are no longer required.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.
Without this fix, the link could reset and result in
a link flap.
The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes. The other
places where changes were detected previously can be removed.
Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Signed-of-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is renamed to make it a little more clear what it does.
It is not added to any .h because it is not for general consumption, only for
bpf internal use (and so by the jits).
Signed-of-by: Jan Seiffert <kaffeemonster@googlemail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The explanation of ip_local_port_range in
Documentation/networking/ip-sysctl.txt contains several factual
errors:
- The default value of ip_local_port_range does not depend on the
amount of memory available in the system.
- tcp_tw_recycle is not enabled by default.
- 1024-4999 is not the default value.
- Etc.
Clean up the mess.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)
The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.
4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)
This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)
In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.
Call tcp_push() only if MSG_MORE is not set in the flags parameter.
This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.
In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail>com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f04565ddf5 (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.
When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)
Problem is after above commit, we dont restart the lookup at right
position in ->start() method.
Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.
This also reverts commit 5cac98dd0 (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mihai Maruseac <mmaruseac@ixiacom.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the below section mismatch warning and alike:
WARNING: vmlinux.o(.text+0x281d4): Section mismatch in reference from
the function setup_ehci_io_mux() to the function
.init.text:omap_mux_init_signal()
The function setup_ehci_io_mux() references
the function __init omap_mux_init_signal().
This is often because setup_ehci_io_mux lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_OMAP4_ERRATA_I688 enabled, omap2+ build
was broken as below:
arch/arm/kernel/io.c: In function '_memcpy_toio':
arch/arm/kernel/io.c:29: error: implicit declaration of function 'outer_sync'
make[1]: *** [arch/arm/kernel/io.o] Error 1
This was caused by commit 9f97da78 (Disintegrate asm/system.h for ARM).
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize fixed regulators in the board files. Trying to
do this in a generic way in gpmc-smsc911x.c gets messy as
the regulator may be provided by drivers, such as twl4030,
for some boards.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: combined into one patch, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding in support for regulators here creates several headaches.
- Boards that declare their own regulator cannot use this function.
- Multiple calls to this function require special handling.
- Boards that declare id's other than '0' need special handling.
Now that there is a simple regulator_register_fixed, we can push
this registration back into the board files.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking back into git history, this code was never used and was
probably left over from a copy/paste.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If this function is called the first time with flags set, and the
second time without flags set then the leftover flags from the first
called will be used rather than the desired default flags.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This seems to be a leftover from when gpmc-smsc911x.c was copied
from gpmc-smc91x.c.
Signed-off-by: Russ Dill <russ.dill@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull drm update from Dave Airlie:
"This pull just contains a forward of the Intel fixes from Daniel.
The only annoyance is the RC6 enable, which really should have made
-next, but since Ubuntu are shipping it I reckon its getting a good
testing now by the time 3.4 comes out.
The pull from Daniel contains his pull message to me:
"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it
still works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year
old, fix curtesy Chris Wilson. I've created an shockingly simple
i-g-t test to catch this in the future."
Wrt regressions I've just got a report that gmbus (newly enabled
again in 3.4) is a bit noisy. I'm looking into this atm.
Also included are the rc6 enable patches for snb from Eugeni. I
wanted to include these in the main 3.4 pull but screwed it up.
Please hit me. Imo these kind of patches really should go in
before -rc1, but in thise case rc6 has brought us tons of press and
guinea pigs^W^W testers and ubuntu is already running with it. So
I estimate a pretty small chance for this to blow up.
And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios
some more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"
Let's see if the "enable RC6 on sandybridge" finally works and sticks.
I've been enabling it by hand (i915.i915_enable_rc6=1) for several
months on my Macbook Air, and it definitely makes a difference (and has
worked for me). But every time we enabled it before it showed some odd
hw buglet for *somebody*.
This time it's all good, I'm sure.
* 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux:
drm/i915: treat src w & h as fixed point in sprite handling code
drm/i915: no-lvds quirk on MSI DC500
drm/i915: Add lock on drm_helper_resume_force_mode
drm/i915: don't leak struct_mutex lock on ppgtt init failures
drm/i915: disable ppgtt on snb when dmar is enabled
drm/i915: add Ivy Bridge GT2 Server entries
drm/i915: properly clear SSC1 bit in the pch refclock init code
drm/i915: apply CS reg readback trick against missed IRQ on snb
drm/i915: quirk away broken OpRegion VBT
drm/i915: enable plain RC6 on Sandy Bridge by default
drm/i915: allow to select rc6 modes via kernel parameter
drm/i915: Mark untiled BLT commands as fenced on gen2/3
drm/i915: properly restore the ppgtt page directory on resume
drm/i915: Sanitize BIOS debugging bits from PIPECONF
Pull drm fixes from Dave Airlie:
"Mainly nouveau fixes, one for a regressions in -rc1, fixes for booting
on a ppc G5, and a Kconfig fix. Two radeon fixes, one oops, one s/r
fix. One udl mmap fix. And one core drm fix to stop bad fbdev apps
overwriting bits of ram."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Validate requested virtual size against allocated fb size
drm/radeon: Don't dereference possibly-NULL pointer.
mm, drm/udl: fixup vma flags on mmap
drm/radeon/kms: fix fans after resume
nouveau/bios: Fix tracking of BIOS image data
nouveau: Fix crash when pci_ram_rom() returns a size of 0
drm/nouveau: select POWER_SUPPLY
drm/nouveau: inform userspace of relaxed kernel subchannel requirements
Revert "drm/nouveau: inform userspace of new kernel subchannel requirements"
drm/nouveau: oops, create m2mf for nvd9 too
Pull arch/microblaze fixes from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix ret_from_fork declaration
microblaze: Do not use tlb_skip in early_printk
microblaze: Add missing headers caused by disintegration asm/system.h
microblaze: Fix stack usage in PAGE_SIZE copy_tofrom_user
microblaze: Fix tlb_skip variable on noMMU system
microblaze: Fix __futex_atomic_op macro register usage
Pull m68k fixes from Geert Uytterhoeven:
"Here are a few fixes for the m68k architecture. Nothing fancy this
time, just a build fix for the asm/system.h disintegration, and two
fixes for missing platform checks (one got in during last merge
window), which can cause crashes in multi-platform kernels."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/q40: Add missing platform check before registering platform devices
m68k/mac: Add missing platform check before registering platform devices
m68k: include asm/cmpxchg.h in our m68k atomic.h
Taps in absolute positioning single-finger mode are currently reported
as physical clicks by the driver. This should be handled by userspace,
not the kernel.
When a tap occurs, the FSP_PB0_LBTN bit is set, but the FSP_PB0_PHY_BTN
is not. We use this to filter out physical clicks from taps.
Signed-off-by: Oskari Saarenmaa <os@ohmu.fi>
Reviewed-by: Tai-hwa Liang <avatar@sentelic.com>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is needed to make module auto loading work.
[dtor@mail.ru: remove file name from comment]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It just bloats the audit data structure for no good reason, since the
only time those fields are filled are just before calling the
common_lsm_audit() function, which is also the only user of those
fields.
So just make them be the arguments to common_lsm_audit(), rather than
bloating that structure that is passed around everywhere, and is
initialized in hot paths.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of declaring the entire selinux_audit_data on the stack when we
start an operation on declare it on the stack if we are going to use it.
We know it's usefulness at the end of the security decision and can declare
it there.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After shrinking the common_audit_data stack usage for private LSM data I'm
not going to shrink the data union. To do this I'm going to move anything
larger than 2 void * ptrs to it's own structure and require it to be declared
separately on the calling stack. Thus hot paths which don't need more than
a couple pointer don't have to declare space to hold large unneeded
structures. I could get this down to one void * by dealing with the key
struct and the struct path. We'll see if that is helpful after taking care of
networking.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus found that the gigantic size of the common audit data caused a big
perf hit on something as simple as running stat() in a loop. This patch
requires LSMs to declare the LSM specific portion separately rather than
doing it in a union. Thus each LSM can be responsible for shrinking their
portion and don't have to pay a penalty just because other LSMs have a
bigger space requirement.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From Daniel Vetter:
"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it still
works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year old, fix
curtesy Chris Wilson. I've created an shockingly simple i-g-t test to
catch this in the future.
Wrt regressions I've just got a report that gmbus (newly enabled again in
3.4) is a bit noisy. I'm looking into this atm.
Also included are the rc6 enable patches for snb from Eugeni. I wanted to
include these in the main 3.4 pull but screwed it up. Please hit me. Imo
these kind of patches really should go in before -rc1, but in thise case
rc6 has brought us tons of press and guinea pigs^W^W testers and ubuntu is
already running with it. So I estimate a pretty small chance for this to
blow up.
And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios some
more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: treat src w & h as fixed point in sprite handling code
drm/i915: no-lvds quirk on MSI DC500
drm/i915: Add lock on drm_helper_resume_force_mode
drm/i915: don't leak struct_mutex lock on ppgtt init failures
drm/i915: disable ppgtt on snb when dmar is enabled
drm/i915: add Ivy Bridge GT2 Server entries
drm/i915: properly clear SSC1 bit in the pch refclock init code
drm/i915: apply CS reg readback trick against missed IRQ on snb
drm/i915: quirk away broken OpRegion VBT
drm/i915: enable plain RC6 on Sandy Bridge by default
drm/i915: allow to select rc6 modes via kernel parameter
drm/i915: Mark untiled BLT commands as fenced on gen2/3
drm/i915: properly restore the ppgtt page directory on resume
drm/i915: Sanitize BIOS debugging bits from PIPECONF
this patch fixes that buf->pages is allocated two times when it allocates
physically continuous memory region and removes unnecessary codes.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
1M section, 64k page count also should be rounded up so this patch
rounds up them and caculates page count of them properly and also
checks memory flags from user.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
regcache_sync_region() isn't going to be useful to most drivers if we
don't export it since otherwise they can't use it when built modular.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mplayer -vo fbdev tries to create a screen that is twice as tall as the
allocated framebuffer for "doublebuffering". By default, and all in-tree
users, only sufficient memory is allocated and mapped to satisfy the
smallest framebuffer and the virtual size is no larger than the actual.
For these users, we should therefore reject any userspace request to
create a screen that requires a buffer larger than the framebuffer
originally allocated.
References: https://bugs.freedesktop.org/show_bug.cgi?id=38138
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
i915_drm_thaw was not locking the mode_config lock when calling
drm_helper_resume_force_mode. When there were multiple wake sources,
this caused FDI training failure on SNB which in turn corrupted the
display.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If CONFIG_NF_CONNTRACK_TIMEOUT=n we have following warning :
CC [M] net/netfilter/xt_CT.o
net/netfilter/xt_CT.c: In function ‘xt_ct_tg_check_v1’:
net/netfilter/xt_CT.c:284: warning: label ‘err4’ defined but not used
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We were leaking preemption counters. Fix the code to always toggle
between preempt and non-preempt properly.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PPC, CR2-CR4 are nonvolatile, thus have to be saved across function calls.
We didn't respect that for any architecture until Paul spotted it in his
patch for Book3S-HV. This patch saves/restores CR for all KVM capable PPC hosts.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ABI specifies that CR fields CR2--CR4 are nonvolatile across function
calls. Currently __kvmppc_vcore_entry doesn't save and restore the CR,
leading to CR2--CR4 getting corrupted with guest values, possibly leading
to incorrect behaviour in its caller. This adds instructions to save
and restore CR at the points where we save and restore the nonvolatile
GPRs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In kvm_alloc_linear we were using and deferencing ri after the
list_for_each_entry had come to the end of the list. In that
situation, ri is not really defined and probably points to the
list head. This will happen every time if the free_linears list
is empty, for instance. This led to a NULL pointer dereference
crash in memset on POWER7 while trying to allocate an HPT in the
case where no HPTs were preallocated.
This fixes it by using a separate variable for the return value
from the loop iterator.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were failing to compile on book3s_32 with the following errors:
arch/powerpc/kvm/book3s_pr.c:883:45: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
arch/powerpc/kvm/book3s_pr.c:898:79: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Fix this by explicity casting the u64 to long before we use it as a pointer.
Also, on PPC32 we can not use get_user/put_user for 64bit wide variables,
as there is no single instruction that could load or store variables that big.
So instead, we have to use copy_from/to_user which works everywhere.
Reported-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When comparing two pages read from different legs of a mirror, only
compare the bytes that were read, not the whole page.
In most cases we read a whole page, but in some cases with
bad blocks or odd sizes devices we might read fewer than that.
This bug has been present "forever" but at worst it might cause
a report of two many mismatches and generate a little bit
extra resync IO, so there is no need to back-port to -stable
kernels.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When create a raid5 using assume-clean and echo check or repair to
sync_action.Then component disks did not operated IO but the raid
check/resync faster than normal.
Because the judgement in function analyse_stripe():
if (do_recovery ||
sh->sector >= conf->mddev->recovery_cp)
s->syncing = 1;
else
s->replacing = 1;
When check or repair,the recovery_cp == MaxSectore,so syncing equal zero
not one.
This bug was introduced by commit 9a3e1101b8
md/raid5: detect and handle replacements during recovery.
so this patch is suitable for 3.3-stable.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because rde->nr_pending > 0,so can not remove this disk.
And in any case, we aren't holding rcu_read_lock()
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raid1 arrays do not have the notion of chunk size. Calculate the
largest chunk sector size we can use to avoid a divide by zero OOPS
when aligning the size of the new array to the chunk size.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
1/ We can only treat a known-bad-block like a read-error if we
have the data that belongs in that block. So fix that test.
2/ If we cannot recovery a stripe due to insufficient data,
don't tell "md_done_sync" that the sync failed unless we really
did fail something. If we successfully record bad blocks,
that is success.
Reported-by: "majianpeng" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit 086ada54ab
"FB: sa1100: remove global sa1100fb_.*_power function pointers"
got rid of all instances but one in locomolcd.c -- which was
conditional on CONFIG_SA1100_COLLIE. The associated .power
field which replaces the global is populated in mach-sa1100/collie.c
so move the assignment there, but make it conditional on the
locomolcd support, so use CONFIG_BACKLIGHT_LOCOMO in that file.
Cc: arm@kernel.org
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 9f786d033d
"arm/PCI: get rid of device resource fixups"
causes this failure on the versatile:
arch/arm/mach-versatile/pci.c: In function 'pci_versatile_setup_resources':
arch/arm/mach-versatile/pci.c:221: error: 'sys' undeclared (first use in this function)
because the versatile wasn't passing in the full struct pci_sys_data
but only the resource sub-field. Change it to pass in the full
struct so that sys will be in scope.
Reported-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
I found the Xorg server on my ARM device stuck in the 'msleep()' loop
in apm_ioctl.
I suspect it had attempted suspend immediately after resuming and lost
a race.
During that msleep(10);, a new suspend cycle must have started and
changed ->suspend_state to SUSPEND_PENDING, so it was never seen to
be SUSPEND_DONE and the loop could never exited. It would have moved on
to SUSPEND_ACKTO but never been able to reach SUSPEND_DONE.
So change the loop to only run while SUSPEND_ACKED rather than until
SUSPEND_DONE. This is much safer.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull dma-buf prime support from Dave Airlie:
"This isn't a majorly urgent thing to have, but we'd like to set the
stage for working on dma-buf support in the drm drivers for the next
merge window, so I'd like to push in the initial submission now so
people have something that we can build on top of. The code just
introduces the user interface and internal helper functions for
drivers to use.
We have driver support under development for i915, nouveau, udl on x86
and exynos, omapdrm on arm, which we would be aiming for the next
merge window."
In the -rc1 announcement I asked for people who would use this to
comment on it, and got severa "Yes please" from people for this and for
HSI (that I merged earlier).
So far crickets on pohmelfs and the DMA-mapping infrastructure.
* 'drm-prime-dmabuf-initial' of git://people.freedesktop.org/~airlied/linux:
drm: base prime/dma-buf support (v5)
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a name collision between 'struct platform_driver
anatop_regulator' and 'struct anatop_regulator', which causes some
section mismatch warnings like below.
WARNING: vmlinux.o(.data+0x154d4): Section mismatch in reference from the variable anatop_regulator to the function .devinit.text:anatop_regulator_probe()
The variable anatop_regulator references
the function __devinit anatop_regulator_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Rename 'struct platform_driver anatop_regulator' to
'struct platform_driver anatop_regulator_driver' to fix the warnings.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* fixes
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: initializer element is not constant
after 23019a733b removed IOMEM
definition from arch/arm/mach-pxa/include/mach/hardware.h
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Debugfs files could be accessed any time, so explicitly enable clocks
when reading registers to generate debugfs file content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As manual described, VAG is an internal voltage reference of DAC/ADC,
So enabled it before DAC/ADC up.
One more thing should care about is VAG fully ramped down requires 400ms,
wait it to avoid pop.
Signed-off-by: Zeng Zhaoming <zengzm.kernel@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This merges some of the fixes from Paul Gortmaker for the header file
cleanup fallout.
Some of the patches are going through arch maintainer trees, and David
Howells suggested another be done differently, but this at least fixes a
few cases.
* emailed from Paul Gortmaker <paul.gortmaker@windriver.com>:
asm-generic: add linux/types.h to cmpxchg.h
firewire: restore the device.h include in linux/firewire.h
frv: fix warnings in mb93090-mb00/pci-dma.c about implicit EXPORT_SYMBOL
parisc: fix missing cmpxchg file error from system.h split
blackfin: fix cmpxchg build fails from system.h fallout
avr32: fix build failures from mis-naming of atmel_nand.h
ARM: mach-msm: fix compile fail from system.h fallout
irq_work: fix compile failure on MIPS from system.h split
If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1. This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Builds of the openrisc or1ksim_defconfig show the following:
In file included from arch/openrisc/include/generated/asm/cmpxchg.h:1:0,
from include/asm-generic/atomic.h:18,
from arch/openrisc/include/generated/asm/atomic.h:1,
from include/linux/atomic.h:4,
from include/linux/dcache.h:4,
from fs/notify/fsnotify.c:19:
include/asm-generic/cmpxchg.h: In function '__xchg':
include/asm-generic/cmpxchg.h:34:20: error: expected ')' before 'u8'
include/asm-generic/cmpxchg.h:34:20: warning: type defaults to 'int' in type name
and many more lines of similar errors. It seems specific to the or32
because most other platforms have an arch specific component that would
have already included types.h ahead of time, but the o32 does not.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 313162d0b8 ("device.h: audit and cleanup users in main include
dir") exchanged an include <linux/device.h> for a struct *device but in
actuality I misread this file when creating 313162d and it should have
remained an include.
There were no build regressions since all consumers were already getting
device.h anyway, but make it right regardless.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To fix:
arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: data definition has no type or storage class [enabled by default]
arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/frv/mb93090-mb00/pci-dma.c:31:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/frv/mb93090-mb00/pci-dma.c:38:1: warning: data definition has no type or storage class [enabled by default]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b4816afa39 ("Move the asm-generic/system.h xchg()
implementation to asm-generic/cmpxchg.h") introduced the concept of
asm/cmpxchg.h but the parisc arch never got one. Fork the cmpxchg
content out of the asm/atomic.h file to create one.
Some minor whitespace fixups were done on the block of code that created
the new file.
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3bed8d6746 ("Disintegrate asm/system.h for Blackfin [ver #2]")
introduced arch/blackfin/include/asm/cmpxchg.h but has it also including
the asm-generic one which causes this:
CC arch/blackfin/kernel/asm-offsets.s
In file included from arch/blackfin/include/asm/cmpxchg.h:125:0,
from arch/blackfin/include/asm/atomic.h:10,
from include/linux/atomic.h:4,
from include/linux/spinlock.h:384,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:57,
from arch/blackfin/kernel/asm-offsets.c:10:
include/asm-generic/cmpxchg.h:24:15: error: redefinition of '__xchg'
arch/blackfin/include/asm/cmpxchg.h:82:29: note: previous definition of '__xchg' was here
make[2]: *** [arch/blackfin/kernel/asm-offsets.s] Error 1
It really only needs two simple defines from asm-generic, so just use
those instead.
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bf4289cba0 ("ATMEL: fix nand ecc support") indicated that it
wanted to "Move platform data to a common header
include/linux/platform_data/atmel_nand.h" and the new header even had
re-include protectors with:
#ifndef __ATMEL_NAND_H__
However, the file that was added was simply called atmel.h
and this caused avr32 defconfig to fail with:
In file included from arch/avr32/boards/atstk1000/setup.c:22:
arch/avr32/mach-at32ap/include/mach/board.h:10:44: error: linux/platform_data/atmel_nand.h: No such file or directory
In file included from arch/avr32/boards/atstk1000/setup.c:22:
arch/avr32/mach-at32ap/include/mach/board.h:121: warning: 'struct atmel_nand_data' declared inside parameter list
arch/avr32/mach-at32ap/include/mach/board.h:121: warning: its scope is only this definition or declaration, which is probably not what you want
make[2]: *** [arch/avr32/boards/atstk1000/setup.o] Error 1
It seems the scope of the file contents will expand beyond
just nand, so ignore the original intention, and fix up the
users who reference the bad name with the _nand suffix.
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
CC: David Woodhouse <dwmw2@infradead.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To fix:
In file included from arm/boot/compressed/misc.c:28:0:
arm/mach-msm/include/mach/uncompress.h: In function 'putc':
arch/arm/mach-msm/include/mach/uncompress.h:48:3: error: implicit
declaration of function 'smp_mb' [-Werror=implicit-function-declaration]
The putc does a cpu_relax which for this platform is smp_mb.
Bisect indicates the 1st failing commit as: 0195c00244 ("Merge tag
'split-asm_system_h...")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When collecting TCP flags we check that the IP header indicates that
a TCP header is present but not that the packet is actually long
enough to contain the header. This adds a check to prevent reading
off the end of the packet.
In practice, this is only likely to result in reading of bad data and
not a crash due to the presence of struct skb_shared_info at the end
of the packet.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Commit e9319b0cb0 ("IB/core: Fix SDR rates in sysfs") changed our
sysfs rate attribute to return EINVAL to userspace if the underlying
device driver returns an invalid rate. Apparently some drivers do this
when the link is down and some userspace pukes if it gets an error when
reading this attribute, so avoid a regression by not return an error to
match the old code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
When the IB port is down, the active_speed value returned by the
MAD_IFC command is seven (7) which isn't among the defined IB speeds
in enum ib_port_speed, and this invalid speed value is passed up to
higher layers or applications who do port query.
Fix that by setting the speed to be SDR -- the lowest possible -- when
the port is down.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit dae2e9f430 changed dev_alloc_skb()
to netdev_alloc_skb(), adding a dev pointer, but erroneously used "->"
instead of "." for a struct member when accessing the dev pointer.
This change fixes the build breakage.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull HSI (High Speed Synchronous Serial Interface) framework from Carlos Chinea:
"The High Speed Synchronous Serial Interface (HSI) is a serial
interface mainly used for connecting application engines (APE) with
cellular modem engines (CMT) in cellular handsets.
The framework is currently being used for some people and we would
like to see it integrated into the kernel for 3.3. There is no HW
controller drivers in this pull, but some people have already some of
them pending which they would like to push as soon as this integrated.
I am also working on the acceptance for an TI OMAP one, based on a
compatible legacy version of the interface called SSI."
Ok, so it didn't get into 3.3, but here it is pulled into 3.4.
Several people piped up to say "yeah, we want this".
* 'for-next' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: hsi_char: Update ioctl-number.txt
HSI: Add HSI API documentation
HSI: hsi_char: Add HSI char device kernel configuration
HSI: hsi_char: Add HSI char device driver
HSI: hsi: Introducing HSI framework
Pull 'make cscope' fix from Michal Marek:
"The kbuild.git#misc pull request introduced a bug that broke make
cscope. Apparently, both the original author and me only tested the
use case that the commit was supposed to improve (make tags/TAGS), and
not the use case that was not supposed (make cscope)."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
tags.sh: Add missing quotes
Pull crypto fixes from Herbert Xu:
- Fix for CPU hotplug hang in padata.
- Avoid using cpu_active inappropriately in pcrypt and padata.
- Fix for user-space algorithm lookup hang with IV generators.
- Fix for netlink dump of algorithms where stuff went missing due to
incorrect calculation of message size.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Fix size of netlink dump message
crypto: user - Fix lookup of algorithms with IV generator
crypto: pcrypt - Use the online cpumask as the default
padata: Fix cpu hotplug
padata: Use the online cpumask as the default
padata: Add a reference to the api documentation
Pull powerpc fixes from Benjamin Herrenschmidt:
"This contains a couple more fixes for the system.h disintegration, a
trivial section mismatch fix, a couple of patches from akpm that I
didn't quite get he expected me to pickup, and a few more trivialities
form Kumar that he appear to have forgotten to send me in the previous
batch."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Fix use of set_current_state() in eeh event handling set_current_state() wart
powerpc/eeh: Remove eeh_event_handler()->daemonize()
powerpc/kvm: Fallout from system.h disintegration
powerpc: Fix fallout from system.h split up
powerpc: Mark const init data with __initconst instead of __initdata
powerpc/qe: Update the SNUM table for MPC8569 Rev2.0
powerpc/dts: Removed fsl,msi property from dts.
powerpc/epapr: add "memory" as a clobber to all hypercalls
powerpc/85xx: Enable I2C_CHARDEV and I2C_MPC options in defconfigs
powerpc/85xx: add the P1020UTM-PC DTS support
powerpc/85xx: add the P1020MBG-PC DTS support
powerpc/8xxx: remove 85xx/86xx restrictions from fsl_guts.h
The bluesmoke mailing list no longer works, so use
linux-edac@vger.kernel.org. And, use a less restrictive pattern so all
drivers/edac changes go to linux-edac as well.
Borislav suggested I just push this through the tile tree since there
is currently no core edac maintainer (emails to Doug Thompson bounce).
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This commit fixes a number of issues seen with the driver:
- Improve handling of return credits to the hardware shim
- Use skb_frag_size() appropriately
- Fix driver so it works properly with netpoll for console over UDP
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This is just an aesthetic change but it was silly to say TILEPro
when booting up on the tilegx architecture.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The return path as we reload registers and core state requires that r30
hold a boolean indicating whether we are returning from an NMI, but in a
couple of cases we weren't setting this properly, with the result that we
could accidentally unmask the NMI interrupt(s), which could cause confusion.
Now we set r30 in every place where we jump into the interrupt return path.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were re-homing the initial task's kernel stack on the boot cpu,
but in fact it's better to let it stay globally homed, since that
task isn't bound to the boot cpu anyway. This is more of a general
cleanup than an actual performance optimization, but it removes
code, which is a good thing. :-)
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we were returning SIGSEGV in this case. It seems cleaner
to return SIGBUS since the hardware figures out alignment traps
before TLB violations, so SIGBUS is the "more correct" signal.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
There were some correctness issues with this code that are now fixed
with this change. The change is likely less performant than it could
be, but it should no longer be vulnerable to any races with memory
operations on the memory network while invalidating a range of memory.
This code is run infrequently so performance isn't critical, but
correctness definitely is.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This idiom is used elsewhere when we do an unlock by writing a zero,
but I missed it here. Using an atomic operation avoids waiting
on the write buffer for the unlocking write to be sent to the home cache.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It causes "make clean" to fail, for example. Once we have KVM support
complete, we'll reinstate the subdir reference.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pragmatically it couldn't be wrong to cast pointers to long to compare
them (since all kernel addresses are in the top half of VA space),
but it's more correct to cast to unsigned long.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If we are single-stepping and make a syscall, we call ptrace_notify()
explicitly on the return path back to user space, since we are returning
to a pc value set artificially to the next instruction, and otherwise
we won't register that we stepped over the syscall instruction (swint1).
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This allows the later-panicking tiles to wait in a lower power state
until they get interrupted with an smp_send_stop().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We should be holding the init_mm.page_table_lock in shatter_huge_page()
since we are modifying the kernel page tables. Then, only if we are
walking the other root page tables to update them, do we want to take
the pgd_lock.
Add a comment about taking the pgd_lock that we always do it with
interrupts disabled and therefore are not at risk from the tlbflush
IPI deadlock as is seen on x86.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We were carefully computing a value to use for the number of loops
to spin for, and then ignoring it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we only handled kernels up to a single huge page in size.
Now we create additional PTEs appropriately.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
If we took a page fault while we had interrupts disabled, we
shouldn't enable them in the page fault handler.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We make sure not to try to set the home for an MMIO PTE (on tilegx)
or a PTE that isn't referencing memory managed by Linux.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Doing so raises the possibility of self-deadlock if we are waiting
for a backtrace for an oprofile or perf interrupt while we are
in the middle of migrating our own stack page.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Not associated with any code changes, so I'm just lumping these
comment changes into a commit by themselves.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
We now respond to MEM_ERROR traps (e.g. an atomic instruction to
non-cacheable memory) with a SIGBUS.
We also no longer generate a console crash message if a user
process die due to a SIGTRAP.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
In certain circumstances we need to do a bunch of jump-and-link
instructions to fill the hardware return-address stack with nonzero values.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Fix a long-standing bug in the stack backtracer where we would print
garbage to the console instead of kernel function names, if the kernel
wasn't built with symbol support (e.g. mboot).
Make sure to tag every line of userspace backtrace output if we actually
have the mmap_sem, since that way if there's no tag, we know that it's
because we couldn't trylock the semaphore.
Stop doing a TLB flush and examining page tables during backtrace.
Instead, just trust that __copy_from_user_inatomic() will properly fault
and return a failure, which it should do in all cases.
Fix a latent bug where the backtracer would directly examine a signal
context in user space, rather than copying it safely to kernel memory
first. This meant that a race with another thread could potentially
have caused a kernel panic.
Guard against unaligned sp when trying to restart backtrace at an
interrupt or signal handler point in the kernel backtracer.
Report kernel symbolic information for the call instruction rather
than for the following instruction. We still report the actual numeric
address corresponding to the instruction after the call, for the sake
of consistency with the normal expectations for stack backtracers.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Add a comment explaining why this is important, and add a CFLAGS_REMOVE
clause to the Makefile to make sure it happens.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
With lockstat we can end up trying to get a backtrace before
"high_memory" is initialized, so don't worry about range testing
if it is zero.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It still returns whether @v was not @u, not the old value,
unlike __atomic_add_unless().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arun Sharma <asharma@fb.com>
We aren't yet using this definition in the kernel, but fix it up
before someone goes looking for it.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Commit bd119c6923
"Disintegrate asm/system.h for Tile"
created the asm/switch_to.h file, but did not add an include
of it to all its users.
Also, commit b4816afa39
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the tile arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull cpumask cleanups from Rusty Russell:
"(Somehow forgot to send this out; it's been sitting in linux-next, and
if you don't want it, it can sit there another cycle)"
I'm a sucker for things that actually delete lines of code.
Fix up trivial conflict in arch/arm/kernel/kprobes.c, where Rusty fixed
a user of &cpu_online_map to be cpu_online_mask, but that code got
deleted by commit b21d55e98a ("ARM: 7332/1: extract out code patch
function from kprobes").
* tag 'for-linus' of git://github.com/rustyrussell/linux:
cpumask: remove old cpu_*_map.
documentation: remove references to cpu_*_map.
drivers/cpufreq/db8500-cpufreq: remove references to cpu_*_map.
remove references to cpu_*_map in arch/
Builds of the MIPS platform ip32_defconfig fails as of commit
0195c00244 ("Merge tag 'split-asm_system_h ...") because MIPS xchg()
macro uses BUILD_BUG_ON and it was moved in commit b81947c646
("Disintegrate asm/system.h for MIPS").
The root cause is that the system.h split wasn't tested on a baseline
with commit 6c03438ede ("kernel.h: doesn't explicitly use bug.h, so
don't include it.")
Since this file uses BUG code in several other places besides the xchg
call, simply make the inclusion explicit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds PCI ID for IVB GT2 server variant which we were missing.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fix up conflict because the patch has been diffed against next. tsk.]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
s2ram broke due to this KVM commit:
b74f05d61b x86: kvmclock: abstract save/restore sched_clock_state
restore_sched_clock_state() methods use percpu data, therefore
they must run after %gs is initialized, but before mtrr_bp_restore()
(due to lockstat using sched_clock).
Move it to the correct place.
Reported-and-tested-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ret_from_fork is used by noMMU system too.
It should be the part of patch
"Disintegrate asm/system.h for Microblaze"
(sha1: c40d04df15)
Signed-off-by: Michal Simek <monstr@monstr.eu>
The code tries various methods for retreiving the BIOS data. However
it doesn't clear the bios->data pointer between the iterations.
In some cases, the shadow() method will fail and not update bios->data
at all, which will cause us to "score" the old data and incorrectly
attribute that score to the new method. This can cause double frees
later when disposing of the unused data.
Additionally, we were not freeing the data for methods that fail the
score test (we only freed when a "best" is superseeded, not when the
new method has a lower score than the exising "best"). Fix that as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From b15b244d6e6e20964bd4b85306722cb60c3c0809 Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Mon, 2 Apr 2012 13:28:18 +1000
Subject:
Under some circumstances, pci_map_rom() can return a valid mapping
but a size of 0 (if it cannot find an image in the header).
This causes nouveau to try to kmalloc() a 0 sized pointer and
dereference it, which crashes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben H. reported that building nouveau into the kernel and power supply
as a module was broken.
Just have nouveau select it, like radeon does.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: inform userspace of relaxed kernel subchannel requirements
Revert "drm/nouveau: inform userspace of new kernel subchannel requirements"
drm/nouveau: oops, create m2mf for nvd9 too
When $remove_structs is empty a test for empty string will turn
into test -n with no arguments meaning true. Add quotes so an
empty string is tested and so that make cscope works again.
Reported-and-tested-by: Jike Song <albcamus@gmail.com>
Reported-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Yang Bai <hamo.by@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Fix the following build warning:
arch/arm/mach-imx/mach-mx35_3ds.c: In function 'mx35_3ds_lcd_set_power':
arch/arm/mach-imx/mach-mx35_3ds.c:112: warning: passing argument 2 of 'gpiochip_find' from incompatible pointer type
include/asm-generic/gpio.h:145: note: expected 'int (*)(struct gpio_chip *, const void *)' but argument is of type 'int (*)(struct gpio_chip *, void *)'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
That set_current_state() won't work very well: the subsequent mutex_lock()
might flip the task back into TASK_RUNNING.
Attempt to put it somewhere where it might have been meant to be, and
attempt to describe why it might have been added.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
daemonize() is only needed when a user-space task does kernel_thread().
eeh_event_handler() thread is created by the worker kthread, and thus it
doesn't need the soon-to-be-deprecated daemonize().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Tested with the Linux USB Ethernet gadget.
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
SuperH has the "CONFIG_CPU_LITTLE_ENDIAN" and the "__LITTLE_ENDIAN__".
But, other architecture doesn't have them. So, this patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist duplicated macro definitions in rtl8150.c, remove them.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes missing mach-s3c24xx/common.h which has been
lost when regarding s3c24xx directories merged.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In cfq, when we calculate a time slice for a process(or a cfqq to
be precise), we have to consider the cfq_target_latency so that all the
sync request have an estimated latency(300ms) and it is controlled by
cfq_target_latency. But in some hadoop test, we have found that if
there are many processes doing sequential read(24 for example), the
throughput is bad because every process can only work for about 25ms
and the cfqq is switched. That leads to a higher disk seek. We can
achive the good throughput by setting low_latency=0, but then some
read's latency is too much for the application.
So this patch makes cfq_target_latency tunable through sysfs so that
we can tune it and find some magic number which is not bad for both
the throughput and the read latency.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In IPv4, if an RTA_IIF attribute is specified within an RTM_GETROUTE
message, then a route is searched as if a packet was received on the
specified 'iif' interface.
However in IPv6, RTA_IIF is not interpreted in the same way:
'inet6_rtm_getroute()' always calls 'ip6_route_output()', regardless the
RTA_IIF attribute.
As a result, in IPv6 there's no way to use RTM_GETROUTE in order to look
for a route as if a packet was received on a specific interface.
Fix 'inet6_rtm_getroute()' so that RTA_IIF is interpreted as "lookup a
route as if a packet was received on the specified interface", similar
to IPv4's 'inet_rtm_getroute()' interpretation.
Reported-by: Ami Koren <amikoren@yahoo.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build breakage in v3.4-rc1:
CC arch/sparc/kernel/cpu.o
In file included from /home/aaro/git/linux/arch/sparc/include/asm/pgtable_64.h:15:0,
from /home/aaro/git/linux/arch/sparc/include/asm/pgtable.h:4,
from arch/sparc/kernel/cpu.c:15:
include/asm-generic/pgtable-nopud.h:13:16: error: unknown type name 'pgd_t'
include/asm-generic/pgtable-nopud.h:25:28: error: unknown type name 'pgd_t'
include/asm-generic/pgtable-nopud.h:26:27: error: unknown type name 'pgd_t'
include/asm-generic/pgtable-nopud.h:27:31: error: unknown type name 'pgd_t'
include/asm-generic/pgtable-nopud.h:28:30: error: unknown type name 'pgd_t'
include/asm-generic/pgtable-nopud.h:38:34: error: unknown type name 'pgd_t'
In file included from /home/aaro/git/linux/arch/sparc/include/asm/pgtable_64.h:783:0,
from /home/aaro/git/linux/arch/sparc/include/asm/pgtable.h:4,
from arch/sparc/kernel/cpu.c:15:
include/asm-generic/pgtable.h: In function 'pgd_none_or_clear_bad':
include/asm-generic/pgtable.h:258:2: error: implicit declaration of function 'pgd_none' [-Werror=implicit-function-declaration]
include/asm-generic/pgtable.h:260:2: error: implicit declaration of function 'pgd_bad' [-Werror=implicit-function-declaration]
include/asm-generic/pgtable.h: In function 'pud_none_or_clear_bad':
include/asm-generic/pgtable.h:269:6: error: request for member 'pgd' in something not a structure or union
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
On multi-platform kernels, the Q40/Q60 platform devices should be
registered when running on Q40/Q60 only. Else it may crash later.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
On multi-platform kernels, the Mac platform devices should be registered
when running on Mac only. Else it may crash later.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
After commit 9ffc93f203 ("Remove all
CC init/main.o
In file included from include/linux/mm.h:15:0,
from include/linux/ring_buffer.h:5,
from include/linux/ftrace_event.h:4,
from include/trace/syscall.h:6,
from include/linux/syscalls.h:78,
from init/main.c:16:
include/linux/debug_locks.h: In function ‘__debug_locks_off’:
include/linux/debug_locks.h:16:2: error: implicit declaration of function ‘xchg’
There is no indirect inclusions of the new asm/cmpxchg.h for m68k here.
Looking at most other architectures they include asm/cmpxchg.h in their
asm/atomic.h. M68k currently does not do this. Including this in atomic.h
fixes all m68k build problems.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been
renamed to eth_hw_addr_random(). This patch fixes it also in the new driver
lpc_eth.c.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If both addresses equal, nothing needs to be done. If the device is down,
then we simply copy the new address to dev->dev_addr. If the device is up,
then we add another loopback device with the new address, and if that does
not fail, we remove the loopback device with the old address. And only
then, we update the dev->dev_addr.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An infinite loop occurred if garp_attr_create was called with the values
of an existing attribute. This might happen if a previous leave request
for the attribute has not yet been followed by a PDU transmission (or,
if the application previously issued a join request for the attribute
and is now issuing another one, without having issued a leave request).
If garp_attr_create finds an existing attribute having the same values,
return the address to it. Its state will then get updated (i.e., if it
was in a leaving state, it will move into a non-leaving state and not
get deleted during the next PDU transmission).
To accomplish this fix, collapse garp_attr_insert into garp_attr_create
(which is its only caller).
Thanks to Jorge Boncompte [DTI2] <jorge@dti2.net> for contributing to
this fix.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can deadlock if we have a write oplock and two processes
use the same file handle. In this case the first process can't
unlock its lock if the second process blocked on the lock in the
same time.
Fix it by using posix_lock_file rather than posix_lock_file_wait
under cinode->lock_mutex. If we request a blocking lock and
posix_lock_file indicates that there is another lock that prevents
us, wait untill that lock is released and restart our call.
Cc: stable@kernel.org
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Similar to a30dcb4f which fixed asus_atk0110.ko, I recently received a
bug report from someone hitting the same issue in acpi_power_meter.
[ 13.963168] power_meter ACPI000D:00: Found ACPI power meter.
[ 13.963900] BUG: key ffff8802161f3920 not in .data!
[ 13.963904] ------------[ cut here ]------------
[ 13.963915] WARNING: at kernel/lockdep.c:2986
lockdep_init_map+0x52f/0x560()
So let's fix that up for them by statically declaring the
lockdep_class_key.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Some configurations produce the following compile warning:
drivers/hwmon/adm1031.c: In function 'set_fan_auto_channel':
drivers/hwmon/adm1031.c:292: warning: 'reg' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from get_fan_auto_nearest with both register value and error return code
(the register value is never negative). Coincidentially, that also reduces
module size by a few bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
In some configurations, BUG() does not result in an endless loop but returns to
the caller. This results in the following compiler warning:
drivers/hwmon/f75375s.c: In function 'duty_mode_enabled':
drivers/hwmon/f75375s.c:280: warning: control reaches end of non-void function
drivers/hwmon/f75375s.c: In function 'auto_mode_enabled':
drivers/hwmon/f75375s.c:295: warning: control reaches end of non-void function
Fix the warning by returning something sensible after BUG().
Cc: Nikolaus Schulz <schulz@macnetix.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The I2C specific PM operations have been deprecated and printing a
warning on boot for over a year now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[guenter.roeck@ericsson.com: Added missing #ifdef around pm functions]
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
sht15 depends on GPIOLIB, not on GENERIC_GPIO.
This fixes the following build error, seen if GPIOLIB is not defined:
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_direction_input': => 293:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_direction_output': => 216:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_free': => 1000:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_get_value': => 296:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_request': => 946:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_set_value': => 218:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_to_irq': => 514:2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
gpio-fan depends on GPIOLIB, not on GENERIC_GPIO.
This fixes the following build error, seen if GPIOLIB is not defined:
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_direction_output': => 372:3
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_free': => 130:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_get_value': => 79:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_request': => 98:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_set_value': => 156:3
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_to_irq': => 114:2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Simon Guinot <sguinot@lacie.com>
The code currently passes the register offset in the current block to
regcache_lookup_reg. This works fine as long as there is only one block and with
base register of 0, but in all other cases it will look-up the default for a
wrong register, which can cause unnecessary register writes. This patch fixes
it by passing the actual register number to regcache_lookup_reg.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org>
Noticed by staring at intel_reg_dumper diffs. Unfortunately it does
not seem to completely fix the bug.
Still, it's good to get this right, and maybe it helps someplace else.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47117
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky reported missed IRQ issues and this patch here helps.
We have one other missed IRQ report still left on snb, reported by QA:
https://bugs.freedesktop.org/show_bug.cgi?id=46145
This is _not_ a regression due to the forcewake voodoo though, it
started showing up before that was applied and has been on-and-off for
the past few weeks. According to QA this patch does not help. But the
missed IRQ is always from the blt ring (despite running piglit, so
also render activity expected), so I'm hopefully that this is an issue
with the blt ring itself.
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is yet another chapter in the ongoing saga of bringing RC6 to Sandy
Bridge machines by default.
Now that we have discovered that RC6 issues are triggered by RC6+ state,
let's try to disable it by default. Plain RC6 is the one responsible for
most energy savings, and so far it haven't given any problems - at least,
none we are aware of.
So with this, when i915_enable_rc6=-1 (e.g., the default value), we'll
attempt to enable plain RC6 only on SNB. For Ivy Bridge, the behavior
stays the same as always - we enable both RC6 and deep RC6.
Note that while this exact patch does not has explicit tested-by's, the
equivalent settings were fixed in 3.3 kernel by a smaller patch. And it
has also received considerable testing through Canonical RC6 task-force
testing at https://wiki.ubuntu.com/Kernel/PowerManagementRC6. Up to date,
it looks like all the known issues are gone.
v2: improve description and reference a couple of open bugs related to
RC6 which seem to be fixed with this change.
References: https://bugs.freedesktop.org/show_bug.cgi?id=41682
References: https://bugs.freedesktop.org/show_bug.cgi?id=38567
References: https://bugs.freedesktop.org/show_bug.cgi?id=44867
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to select which rc6 modes are to be used via kernel parameter,
via a bitmask parameter. E.g.:
- to enable rc6, i915_enable_rc6=1
- to enable rc6 and deep rc6, i915_enable_rc6=3
- to enable rc6 and deepest rc6, use i915_enable_rc6=5
- to enable rc6, deep and deepest rc6, use i915_enable_rc6=7
Please keep in mind that the deepest RC6 state really should NOT be used
by default, as it could potentially worsen the issues with deep RC6. So do
enable it only when you know what you are doing. However, having it around
could help solving possible future rc6-related issues and their debugging
on user machines.
Note that this changes behavior - previously, value of 1 would enable both
RC6 and deep RC6. Now it should only enable RC6 and deep/deepest RC6
stages must be enabled manually.
v2: address Chris Wilson comments and clean up the code.
References: https://bugs.freedesktop.org/show_bug.cgi?id=42579
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ppgtt page directory lives in a snatched part of the gtt pte
range. Which naturally gets cleared on hibernate when we pull the
power. Suspend to ram (which is what I've tested) works because
despite the fact that this is a mmio region, it is actually back by
system ram.
Fix this by moving the page directory setup code to the ppgtt init
code (which gets called on resume).
This fixes hibernate on my ivb and snb.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"s6->sin6_scope_id" is an int bits but strict_strtoul() writes a long
so this can corrupt memory on 64 bit systems.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
gcc-4.7.0 has started throwing these warnings when building cifs.ko.
CC [M] fs/cifs/cifssmb.o
fs/cifs/cifssmb.c: In function ‘CIFSSMBSetCIFSACL’:
fs/cifs/cifssmb.c:3905:9: warning: array subscript is above array bounds [-Warray-bounds]
fs/cifs/cifssmb.c: In function ‘CIFSSMBSetFileInfo’:
fs/cifs/cifssmb.c:5711:8: warning: array subscript is above array bounds [-Warray-bounds]
fs/cifs/cifssmb.c: In function ‘CIFSSMBUnixSetFileInfo’:
fs/cifs/cifssmb.c:6001:25: warning: array subscript is above array bounds [-Warray-bounds]
This patch cleans up the code a bit by using the offsetof macro instead
of the funky "&pSMB->hdr.Protocol" construct.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We can deadlock if we have a write oplock and two processes
use the same file handle. In this case the first process can't
unlock its lock if another process blocked on the lock in the
same time.
Fix this by removing lock_mutex protection from waiting on a
blocked lock and protect only posix_lock_file call.
Cc: stable@kernel.org
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This option has been selected from arch code as it was assumed that
it's necessary to support oneshot mode clockevent devices. But it's
just a core internal helper to compile tick-oneshot.c if NOHZ or
HIG_RES_TIMERS are selected.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When regulator_register_fixed() is being used to register fixed dummy
regulator, the following line will be seen in the boot log. And the
sysfs entry for fixed dummy regulator is not shown.
dummy: Failed to create debugfs directory
The patch renames the fixed dummy supply to "fixed-dummy" to avoid
the name collision with dummy regulator.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. TRACE_EVENT(sched_process_exec) forgets to actually use the
old pid argument, it sets ->old_pid = p->pid.
2. search_binary_handler() uses the wrong pid number. tracepoint
needs the global pid_t from the root namespace, while old_pid
is the virtual pid number as it seen by the tracer/parent.
With this patch we have two pid_t's in search_binary_handler(),
not really nice. Perhaps we should switch to "struct pid*", but
in this case it would be better to cleanup the current code
first and move the "depth == 0" code outside.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: David Smith <dsmith@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Link: http://lkml.kernel.org/r/20120330162636.GA4857@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
arch/arm/kernel/io.c: In function '_memcpy_toio':
arch/arm/kernel/io.c:29: error: implicit declaration of function 'outer_sync'
arch/arm/mach-omap2/omap_l3_noc.c: In function 'l3_interrupt_handler':
arch/arm/mach-omap2/omap_l3_noc.c💯 error: implicit declaration of function 'outer_sync'
kernel/irq/generic-chip.c: In function 'irq_gc_mask_disable_reg':
kernel/irq/generic-chip.c:45: error: implicit declaration of function 'outer_sync'
kernel/sched/rt.c: In function 'rt_set_overload':
kernel/sched/rt.c:248: error: implicit declaration of function 'outer_sync'
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed device initialization to be children of the
bus master, not children of the bus masters parent device. The pdata
pointer used in fsl_spi_chipselect must updated to reflect the changed
initialization.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver uses NULL for dma_unmap_single instead of
the struct device that the API expects.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Tested-by: Akshay Shankarmurthy <akshay.s@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
linux/pl022.h uses definitions like, u8, u16, etc, which have dependency of
types.h file, which isn't included in it. So, we get compilation warnings.
This patch includes types.h there to fix these warnings.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
arch/arm/kernel/bios32.c: In function 'pcibios_fixup_bus':
arch/arm/kernel/bios32.c:302: warning: unused variable 'root'
caused by 9f786d033 (arm/PCI: get rid of device resource fixups)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On gccs that support AVX it's a good idea to disable that too, similar to
how SSE2, SSE1 etc. are already disabled. This prevents the compiler
from generating AVX ever implicitely.
No failure observed, just from review.
[ hpa: Marking this for urgent and stable, simply because the patch
will either have absolutely no effect *or* it will avoid potentially
very hard to debug failures. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1332960678-11879-1-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@vger.kernel.org>
Make this function consistent with others in this module by
returning 1 for error, instead of -ENOMEM
(reverts function signature change from a938fb1e)
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Git commit a25cac5198 "proc: Consider NO_HZ when printing idle and
iowait times" changes the code for /proc/stat to use get_cpu_idle_time_us
and get_cpu_iowait_time_us if the system is running with nohz enabled.
For architectures which define arch_idle_time (currently s390 only)
this is a change for the worse. The result of arch_idle_time is supposed
to be the exact sleep time of the target cpu and should be used instead
of the value kept by the scheduler.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20120330122308.18720283@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
setitimer() should return -EFAULT if called with an invalid pointer
for value. The current code excludes a NULL pointer from this rule and
silently uses it to stop the timer. This violates the spec.
Warn about user space apps which rely on that feature and schedule it
for removal.
[ tglx: Massaged changelog, warn message and Doc entry ]
Signed-off-by: Sasikantha babu <sasikanth.v19@gmail.com>
Link: http://lkml.kernel.org/r/1332340854-26053-1-git-send-email-sasikanth.v19@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The device is a bluetooth device, but one occurence by mistake
had marked it as USB.
Reported-by: Joshua Dillon <jvdillon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 68b7f715 ("nommu: ptrace support") added definitions for
PT_TEXT_ADDR and friends, as well as adding ptrace support for reading
from these magic offsets.
Unfortunately, this has probably never worked, since ptrace_read_user
predicates reading on off < sizeof(struct user), returning -EIO
otherwise.
This patch moves the offset size check until after we have tried to
match it against either a magic value or an offset into pt_regs.
Cc: Paul Brook <paul@codesourcery.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the basic drm dma-buf interface layer, called PRIME. This
commit doesn't add any driver support, it is simply and agreed upon starting
point so we can work towards merging driver support for the next merge window.
Current drivers with work done are nouveau, i915, udl, exynos and omap.
The main APIs exposed to userspace allow translating a 32-bit object handle
to a file descriptor, and a file descriptor to a 32-bit object handle.
The flags value is currently limited to O_CLOEXEC.
Acknowledgements:
Daniel Vetter: lots of review
Rob Clark: cleaned up lots of the internals and did lifetime review.
v2: rename some functions after Chris preferred a green shed
fix IS_ERR_OR_NULL -> IS_ERR
v3: Fix Ville pointed out using buffer + kmalloc
v4: add locking as per ickle review
v5: allow re-exporting the original dma-buf (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
arch/arm/kernel/insn.c: In function '__arm_gen_branch_thumb2':
arch/arm/kernel/insn.c:13: error: implicit declaration of function 'WARN_ON_ONCE'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Follows the 8250 change for pretty much the same rationale.
See commit "serial: use serial_port_in/out vs serial_in/out in 8250".
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The recent merge of the sa11x0 code into mainline had silent conflicts
with further development of the DMA engine API, leading to build errors
and warnings:
drivers/net/irda/sa1100_ir.c: In function 'sa1100_irda_dma_start':
drivers/net/irda/sa1100_ir.c:151: error: too few arguments to function 'chan->device->device_prep_slave_sg'
drivers/dma/sa11x0-dma.c: In function 'sa11x0_dma_probe':
drivers/dma/sa11x0-dma.c:950: warning: assignment from incompatible pointer type
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some improper formatting caused the .eh_frame generation to fail,
resulting in gcc/g++ testsuite failures with regards to unwinding through
the vDSO. Now that someone is actually working on this on the gcc side
it's time to fix up the kernel side, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there's no SHmedia support plugged in for the dwarf unwinder.
While it's trivial to provide an SHmedia version of dwarf_read_arch_reg(),
the general sh64 case is more complicated in that the TLB miss handler
uses a locked down set of registers for optimization (including the frame
pointer) which we need for the unwind table generation.
While freeing up the frame pointer for use in the TLB miss handler is
reasonably straightforward, it's still more trouble than it's worth, so
we simply restrict the unwinder to 32-bit for now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If access to user space failed we need to reconstruct
stack pointer and restore all register.
This patch fixed problem introduces by:
"microblaze: Add loop unrolling for PAGE in copy_tofrom_user"
(sha1: ebe211254b)
Signed-off-by: Michal Simek <monstr@monstr.eu>
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There has long been a limitation using software breakpoints with a
kernel compiled with CONFIG_DEBUG_RODATA going back to 2.6.26. For
this particular patch, it will apply cleanly and has been tested all
the way back to 2.6.36.
The kprobes code uses the text_poke() function which accommodates
writing a breakpoint into a read-only page. The x86 kgdb code can
solve the problem similarly by overriding the default breakpoint
set/remove routines and using text_poke() directly.
The x86 kgdb code will first attempt to use the traditional
probe_kernel_write(), and next try using a the text_poke() function.
The break point install method is tracked such that the correct break
point removal routine will get called later on.
Cc: x86@kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # >= 2.6.36
Inspried-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There is extra state information that needs to be exposed in the
kgdb_bpt structure for tracking how a breakpoint was installed. The
debug_core only uses the the probe_kernel_write() to install
breakpoints, but this is not enough for all the archs. Some arch such
as x86 need to use text_poke() in order to install a breakpoint into a
read only page.
Passing the kgdb_bpt structure to kgdb_arch_set_breakpoint() and
kgdb_arch_remove_breakpoint() allows other archs to set the type
variable which indicates how the breakpoint was installed.
Cc: stable@vger.kernel.org # >= 2.6.36
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The do_fork and sys_open tests have never worked properly on anything
other than a UP configuration with the kgdb test suite. This is
because the test suite did not fully implement the behavior of a real
debugger. A real debugger tracks the state of what thread it asked to
single step and can correctly continue other threads of execution or
conditionally stop while waiting for the original thread single step
request to return.
Below is a simple method to cause a fatal kernel oops with the kgdb
test suite on a 2 processor ARM system:
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
echo V1I1F100 > /sys/module/kgdbts/parameters/kgdbts
Very soon after starting the test the kernel will start warning with
messages like:
kgdbts: BP mismatch c002487c expected c0024878
------------[ cut here ]------------
WARNING: at drivers/misc/kgdbts.c:317 check_and_rewind_pc+0x9c/0xc4()
[<c01f6520>] (check_and_rewind_pc+0x9c/0xc4)
[<c01f595c>] (validate_simple_test+0x3c/0xc4)
[<c01f60d4>] (run_simple_test+0x1e8/0x274)
The kernel will eventually recovers, but the test suite has completely
failed to test anything useful.
This patch implements behavior similar to a real debugger that does
not rely on hardware single stepping by using only software planted
breakpoints.
In order to mimic a real debugger, the kgdb test suite now tracks the
most recent thread that was continued (cont_thread_id), with the
intent to single step just this thread. When the response to the
single step request stops in a different thread that hit the original
break point that thread will now get continued, while the debugger
waits for the thread with the single step pending. Here is a high
level description of the sequence of events.
cont_instead_of_sstep = 0;
1) set breakpoint at do_fork
2) continue
3) Save the thread id where we stop to cont_thread_id
4) Remove breakpoint at do_fork
5) Reset the PC if needed depending on kernel exception type
6) soft single step
7) Check where we stopped
if current thread != cont_thread_id {
if (here for more than 2 times for the same thead) {
### must be a really busy system, start test again ###
goto step 1
}
goto step 5
} else {
cont_instead_of_sstep = 0;
}
8) clean up and run test again if needed
9) Clear out any threads that were waiting on a break point at the
point in time the test is ended with get_cont_catch(). This
happens sometimes because breakpoints are used in place of single
stepping and some threads could have been in the debugger exception
handling queue because breakpoints were hit concurrently on
different CPUs. This also means we wait at least one second before
unplumbing the debugger connection at the very end, so as respond
to any debug threads waiting to be serviced.
Cc: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The do_fork and sys_open tests have never worked properly on anything
other than a UP configuration with the kgdb test suite. This is
because the test suite did not fully implement the behavior of a real
debugger. A real debugger tracks the state of what thread it asked to
single step and can correctly continue other threads of execution or
conditionally stop while waiting for the original thread single step
request to return.
Below is a simple method to cause a fatal kernel oops with the kgdb
test suite on a 4 processor x86 system:
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
echo V1I1F1000 > /sys/module/kgdbts/parameters/kgdbts
Very soon after starting the test the kernel will oops with a message like:
kgdbts: BP mismatch 3b7da66480 expected ffffffff8106a590
WARNING: at drivers/misc/kgdbts.c:303 check_and_rewind_pc+0xe0/0x100()
Call Trace:
[<ffffffff812994a0>] check_and_rewind_pc+0xe0/0x100
[<ffffffff81298945>] validate_simple_test+0x25/0xc0
[<ffffffff81298f77>] run_simple_test+0x107/0x2c0
[<ffffffff81298a18>] kgdbts_put_char+0x18/0x20
The warn will turn to a hard kernel crash shortly after that because
the pc will not get properly rewound to the right value after hitting
a breakpoint leading to a hard lockup.
This change is broken up into 2 pieces because archs that have hw
single stepping (2.6.26 and up) need different changes than archs that
do not have hw single stepping (3.0 and up). This change implements
the correct behavior for an arch that supports hw single stepping.
A minor defect was fixed where sys_open should be do_sys_open
for the sys_open break point test. This solves the problem of running
a 64 bit with a 32 bit user space. The sys_open() never gets called
when using the 32 bit file system for the kgdb testsuite because the
32 bit binaries invoke the compat_sys_open() call leading to the test
never completing.
In order to mimic a real debugger, the kgdb test suite now tracks the
most recent thread that was continued (cont_thread_id), with the
intent to single step just this thread. When the response to the
single step request stops in a different thread that hit the original
break point that thread will now get continued, while the debugger
waits for the thread with the single step pending. Here is a high
level description of the sequence of events.
cont_instead_of_sstep = 0;
1) set breakpoint at do_fork
2) continue
3) Save the thread id where we stop to cont_thread_id
4) Remove breakpoint at do_fork
5) Reset the PC if needed depending on kernel exception type
6) if (cont_instead_of_sstep) { continue } else { single step }
7) Check where we stopped
if current thread != cont_thread_id {
cont_instead_of_sstep = 1;
goto step 5
} else {
cont_instead_of_sstep = 0;
}
8) clean up and run test again if needed
Cc: stable@vger.kernel.org # >= 2.6.26
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
On x86 the kgdb test suite will oops when the kernel is compiled with
CONFIG_DEBUG_RODATA and you run the tests after boot time. This is
regression has existed since 2.6.26 by commit: b33cb815 (kgdbts: Use
HW breakpoints with CONFIG_DEBUG_RODATA).
The test suite can use hw breakpoints for all the tests, but it has to
execute the hardware breakpoint specific tests first in order to
determine that the hw breakpoints actually work. Specifically the
very first test causes an oops:
# echo V1I1 > /sys/module/kgdbts/parameters/kgdbts
kgdb: Registered I/O driver kgdbts.
kgdbts:RUN plant and detach test
Entering kdb (current=0xffff880017aa9320, pid 1078) on processor 0 due to Keyboard Entry
[0]kdb> kgdbts: ERROR PUT: end of test buffer on 'plant_and_detach_test' line 1 expected OK got $E14#aa
WARNING: at drivers/misc/kgdbts.c:730 run_simple_test+0x151/0x2c0()
[...oops clipped...]
This commit re-orders the running of the tests and puts the RODATA
check into its own function so as to correctly avoid the kernel oops
by detecting and using the hw breakpoints.
Cc: <stable@vger.kernel.org> # >= 2.6.26
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The Smatch tool warned that the change from commit b8adde8dd
(kdb: Avoid using dbg_io_ops until it is initialized) should
add another null check later in the kdb_printf().
It is worth noting that the second use of dbg_io_ops->is_console
is protected by the KDB_PAGER state variable which would only
get set when kdb is fully active and initialized. If we
ever encounter changes or defects in the KDB_PAGER state
we do not want to crash the kernel in a kdb_printf/printk.
CC: Tim Bird <tim.bird@am.sony.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When K >= 0xFFFF0000, AND needs the two least significant bytes of K as
its operand, but EMIT2() gives it the least significant byte of K and
0x2. EMIT() should be used here to replace EMIT2().
Signed-off-by: Feiran Zhuang <zhuangfeiran@ict.ac.cn>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
How to reproduce this bug ?
-----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24 \--|-- eth1-/ |
--------------------------------
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a regulator with a supply is being unregistered we will call
regulator_put() to release the supply with the regulator_list_mutex held
but this deadlocks as regulator_put() takes the same lock. Fix this by
releasing the supply before we take the mutex in regulator_unregister().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pcpu_dump_alloc_info() was printing continued lines without KERN_CONT.
Use it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
The default irq_disable() sematics are to mark the interrupt disabled,
but keep it unmasked. If the interrupt is delivered while marked
disabled, the low level interrupt handler masks it and marks it
pending. This is important for detecting wakeup interrupts during
suspend and for edge type interrupts to avoid losing interrupts.
fixup_irqs() moves the interrupts away from an offlined cpu. For
certain interrupt types it needs to mask the interrupt line before
changing the affinity. After affinity has changed the interrupt line
is unmasked again, but only if it is not marked disabled.
This breaks the lazy irq disable semantics and causes problems in
suspend as the interrupt can be lost or wakeup functionality is
broken.
Check irqd_irq_masked() instead of irqd_irq_disabled() because
irqd_irq_masked() is only set, when the core code actually masked the
interrupt line. If it's not set, we unmask the interrupt and let the
lazy irq disable logic deal with an eventually incoming interrupt.
[ tglx: Massaged changelog and added a comment ]
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Link: http://lkml.kernel.org/r/27240C0AC20F114CBF8149A2696CBE4A05DFB3@SHSMSX101.ccr.corp.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit a81f15499887d3f9f24ec70bb9b7e778942a6b7b.
Gah, we have a released userspace component using fixed subc assignment
that conflicts with this. To avoid breaking ABI this needs to be
reverted.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The association in the decice tree between PCI and MSI
using fsl,msi property was an artificial one and it does
not reflect the actual hardware.
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The "memory" clobber tells the compiler to ensure that all writes to memory
are committed before the hypercall is made.
"memory" is only necessary for hcalls where the Hypervisor will read or
write guest memory. However, we add it to all hcalls because the impact is
minimal, and we want to ensure that it's present for the hcalls that need
it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable I2C char dev interface for user space testing of I2C controler.
Enable the I2C driver on 64-bit builds (corenet64_smp_defconfig) as it
was missing.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the check for CONFIG_PPC_85xx and CONFIG_PPC_86xx from fsl_guts.h.
The check was originally intended to allow the same header file to
be used on 85xx and 86xx systems, even though the Global Utilities
register could be different. It turns out that they're not actually
different, and so the check is not necessary. In addition, neither
macro is defined for 64-bit e5500 kernels, so that causes a build
break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The default netlink message size limit might be exceeded when dumping a
lot of algorithms to userspace. As a result, not all of the instantiated
algorithms dumped to userspace. So calculate an upper bound on the message
size and call netlink_dump_start() with that value.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We lookup algorithms with crypto_alg_mod_lookup() when instantiating via
crypto_add_alg(). However, algorithms that are wrapped by an IV genearator
(e.g. aead or genicv type algorithms) need special care. The userspace
process hangs until it gets a timeout when we use crypto_alg_mod_lookup()
to lookup these algorithms. So export the lookup functions for these
algorithms and use them in crypto_add_alg().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We use the active cpumask to determine the superset of cpus
to use for parallelization. However, the active cpumask is
for internal usage of the scheduler and therefore not the
appropriate cpumask for these purposes. So use the online
cpumask instead.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We don't remove the cpu that went offline from our cpumasks
on cpu hotplug. This got lost somewhere along the line, so
restore it. This fixes a hang of the padata instance on cpu
hotplug.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We use the active cpumask to determine the superset of cpus
to use for parallelization. However, the active cpumask is
for internal usage of the scheduler and therefore not the
appropriate cpumask for these purposes. So use the online
cpumask instead.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
What we want is to disable output by setting [LDOx|DCx]_HIB_MODE bits.
Current code also clears other bits in LDOx/DCDCx Low Power register.
R202 (CAh) LDO1 Low Power
BIT[13:12] LDO1 Hibernate behaviour:
00 = Select voltage image settings
01 = disable output
10 = reserved
11 = reserved
R182 (B6h) DCDC1 Low Power
BIT[14:12] DC-DC1 Hibernate behaviour:
000 = Use current settings (no change)
001 = Select voltage image settings
010 = Force standby mode
011 = Force standby mode and voltage image settings.
100 = Force LDO mode
101 = Force LDO mode and voltage image settings.
110 = Reserved.
111 = Disable output
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set BIT[8] of LDO7 ON Control mode for low power mode.
R16507 (407Bh) LDO7 ON Control
BIT[8] LDO7_ON_MODE: LDO7 ON Operating Mode
0 = Normal mode
1 = Low Power mode
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x21e1
bcdDevice 1.12
iManufacturer 1 Broadcom Corp
iProduct 2 BCM20702A0
iSerial 3 60D819F0338C
bNumConfigurations 1
Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.
Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads
correctly.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If a virtio disk is open in guest and a disk resize operation is done,
(virsh blockresize), new size is not visible to tools like "fdisk -l".
This seems to be happening as we update only part->nr_sects and not
bdev->bd_inode size.
Call revalidate_disk() which should take care of it. I tested growing disk
size of already open disk and it works for me.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The new API, pm_qos_update_request_timeout() is to provide a timeout
with pm_qos_update_request.
For example, pm_qos_update_request_timeout(req, 100, 1000), means that
QoS request on req with value 100 will be active for 1000 microseconds.
After 1000 microseconds, the QoS request thru req is reset. If there
were another pm_qos_update_request(req, x) during the 1000 us, this
new request with value x will override as this is another request on the
same req handle. A new request on the same req handle will always
override the previous request whether it is the conventional request or
it is the new timeout request.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Oddly enough a work_struct was already part of the firmware_work
structure but nobody was using it. Instead of creating a new
kthread for each request_firmware_nowait() call just schedule the
work on the system workqueue. This should avoid some overhead
in forking new threads when they're not strictly necessary.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Recent patches to split up the three phases of request_firmware()
lead to a casting away of const in fw_create_instance(). We can
avoid this cast by splitting up fw_create_instance() a bit.
Make _request_firmware_setup() return a struct fw_priv and use
that struct instead of passing struct firmware to
_request_firmware(). Move the uevent and device file creation
bits to the loading phase and rename the function to
_request_firmware_load() to better reflect its purpose.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There is a race condition between the freezer and request_firmware()
such that if request_firmware() is run on one CPU and
freeze_processes() is run on another CPU and usermodehelper_disable()
called by it succeeds to grab umhelper_sem for writing before
usermodehelper_read_trylock() called from request_firmware()
acquires it for reading, the request_firmware() will fail and
trigger a WARN_ON() complaining that it was called at a wrong time.
However, in fact, it wasn't called at a wrong time and
freeze_processes() simply happened to be executed simultaneously.
To avoid this race, at least in some cases, modify
usermodehelper_read_trylock() so that it doesn't fail if the
freezing of tasks has just started and hasn't been completed yet.
Instead, during the freezing of tasks, it will try to freeze the
task that has called it so that it can wait until user space is
thawed without triggering the scary warning.
For this purpose, change usermodehelper_disabled so that it can
take three different values, UMH_ENABLED (0), UMH_FREEZING and
UMH_DISABLED. The first one means that usermode helpers are
enabled, the last one means "hard disable" (i.e. the system is not
ready for usermode helpers to be used) and the second one
is reserved for the freezer. Namely, when freeze_processes() is
started, it sets usermodehelper_disabled to UMH_FREEZING which
tells usermodehelper_read_trylock() that it shouldn't fail just
yet and should call try_to_freeze() if woken up and cannot
return immediately. This way all freezable tasks that happen
to call request_firmware() right before freeze_processes() is
started and lose the race for umhelper_sem with it will be
frozen and will sleep until thaw_processes() unsets
usermodehelper_disabled. [For the non-freezable callers of
request_firmware() the race for umhelper_sem against
freeze_processes() is unfortunately unavoidable.]
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
The core suspend/hibernation code calls usermodehelper_disable() to
avoid race conditions between the freezer and the starting of
usermode helpers and each code path has to do that on its own.
However, it is always called right before freeze_processes()
and usermodehelper_enable() is always called right after
thaw_processes(). For this reason, to avoid code duplication and
to make the connection between usermodehelper_disable() and the
freezer more visible, make freeze_processes() call it and remove the
direct usermodehelper_disable() and usermodehelper_enable() calls
from all suspend/hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
There is no reason to call usermodehelper_disable() before creating
memory bitmaps in hibernate() and software_resume(), so call it right
before freeze_processes(), in accordance with the other suspend and
hibernation code. Consequently, call usermodehelper_enable() right
after the thawing of tasks rather than after freeing the memory
bitmaps.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
If firmware is requested asynchronously, by calling
request_firmware_nowait(), there is no reason to fail the request
(and warn the user) when the system is (presumably temporarily)
unready to handle it (because user space is not available yet or
frozen). For this reason, introduce an alternative routine for
read-locking umhelper_sem, usermodehelper_read_lock_wait(), that
will wait for usermodehelper_disabled to be unset (possibly with
a timeout) and make request_firmware_work_func() use it instead of
usermodehelper_read_trylock().
Accordingly, modify request_firmware() so that it uses
usermodehelper_read_trylock() to acquire umhelper_sem and remove
the code related to that lock from _request_firmware().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Split _request_firmware() into three functions,
_request_firmware_prepare() doing preparatory work that need not be
done under umhelper_sem, _request_firmware_cleanup() doing the
post-error cleanup and _request_firmware() carrying out the remaining
operations.
This change is requisite for moving the acquisition of umhelper_sem
from _request_firmware() to the callers, which is going to be done
subsequently.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: stable@vger.kernel.org
Instead of two functions, read_lock_usermodehelper() and
usermodehelper_is_disabled(), used in combination, introduce
usermodehelper_read_trylock() that will only return with umhelper_sem
held if usermodehelper_disabled is unset (and will return -EAGAIN
otherwise) and make _request_firmware() use it.
Rename read_unlock_usermodehelper() to
usermodehelper_read_unlock() to follow the naming convention of the
new function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Whenever the station informs the AP that it is about to leave the
operating channel, the timestamp should be recorded. It is handled
in scan resume but not in scan start. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With flag 'GFP_ATOMIC', probability of allocation failure is more.
Add error handling after kmalloc() call to avoid null dereference.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect pointer passed to eir_append_data made mgmt_device_connected
event unparsable by mgmt user space entity.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If passed 0 as data_length the (parsed < data_length - 1) test will be
true and cause a buffer overflow. In practice we need at least two bytes
for the element length and type so add a test for it to the very
beginning of the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The parsed variable is already incremented inside the for-loop so there
no need to increment it again (not to mention that the code was
incrementing it the wrong amount).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
When we queue delayed work we hold(chan) and delayed work
shall put(chan) after execution.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch uses the correct flags for checking the HCI_SSP_ENABLED bit.
Without this authentication request was not being initiated.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
DMA_ATTR_NON_CONSISTENT lets the platform to choose to return either
consistent or non-consistent memory as it sees fit. By using this API,
you are guaranteeing to the platform that you have all the correct and
necessary sync points for this memory in the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
DMA_ATTR_WRITE_COMBINE specifies that writes to the mapping may be
buffered to improve performance. It will be used by the replacement for
ARM/ARV32 specific dma_alloc_writecombine() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Introduce new generic mmap method with attributes argument.
This method lets drivers to create a userspace mapping for a DMA buffer
in generic, architecture independent way.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Adapt core x86 and IA64 architecture code for dma_map_ops changes: replace
alloc/free_coherent with generic alloc/free methods.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[removed swiotlb related changes and replaced it with wrappers,
merged with IA64 patch to avoid inter-patch dependences in intel-iommu code]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Introduce new generic alloc and free methods with attributes argument.
Existing alloc_coherent and free_coherent can be implemented on top of the
new calls with NULL attributes argument. Later also dma_alloc_non_coherent
can be implemented using DMA_ATTR_NONCOHERENT attribute as well as
dma_alloc_writecombine with separate DMA_ATTR_WRITECOMBINE attribute.
This way the drivers will get more generic, platform independent way of
allocating dma buffers with specific parameters.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: David Gibson <david@gibson.dropbear.ud.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The values in isink_cur array are microamps.
The regulator core expects get_current_limit callback to return microamps.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current implementation in get_isink_val actually choose the biggest current
limit setting falls within the specified range.
What we want is to choose the smallest current limit setting falls within the
specified range. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code in wm831x_isink_set_current actually set the current limit setting
smaller than specified range.
Fix the logic in wm831x_isink_set_current to choose the smallest current limit
setting falls within the specified range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code in wm831x_buckv_set_current_limit actually set the current limit
setting greater than specified range.
Fix the logic in wm831x_buckv_set_current_limit to choose the
smallest current limit setting falls within the specified range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change "reg" to "anatop-reg-offset" due to there is a warning of handling no
size field in reg.
This patch also adds the missing device-tree binding documentation.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bug: cppcheck reported overflow in array assignment (for loop walks
0 to IOP_ADMA_NUM_SRC_TEST+2, array size is IOP_ADMA_NUM_SRC_TEST).
Reported as: https://bugzilla.kernel.org/show_bug.cgi?id=42677
Test code pq_src array was grown by two elements to correspond with actual
usage (IOP_ADMA_NUM_SRC_TEST+2), stack consumption was kept constant by
modifying the pq_dest two element array which is only used when pq_src
is referenced up to IOP_ADMA_NUM_SRC_TEST elements into the address
of the new last two elements of the pq_src array. This is presumed to
be the original intent but would be reliant on compilers always having
pq_dest contiguous with the final element of pq_src.
Note: This is a re-send of a request for review from two weeks ago.
Looking for review (or shootdown), adding LKML to list for a wider
audience. Thanks.
Updated per review comments of Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Don Morris <don.morris@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While investigating another bug, I found that the code on the incoming path
in __netif_receive_skb will only set skb->skb_iif if it is already 0. When
dev_forward_skb() is used in the case of interfaces like veth, skb_iif may
already have been set. Making dev_forward_skb() cause the packet to look
like a newly received packet would seem to the the correct behaviour here,
as otherwise the wrong incoming interface can be reported for such a packet.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using multicast over a local bridge feeding a number of LXC guests
using veth, the LXC guests are unable to get a response from other guests
when pinging 224.0.0.1. Multicast packets did not appear to be getting
delivered to the network namespaces of the guest hosts, and further
inspection showed that the incoming route was pointing to the loopback
device of the host, not the guest. This lead to the wrong network namespace
being picked up by sockets (like ICMP). Fix this by using the correct
network namespace when creating the inbound route entry.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is desirable to rate limit certain messages, it is not
desirable to rate limit the incrementing of counters associated
with those messages.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLBs are available only for MMU systems.
Error log:
arch/microblaze/kernel/setup.c: In function 'debugfs_tlb':
arch/microblaze/kernel/setup.c:217: error: 'tlb_skip' undeclared (first use in this function)
arch/microblaze/kernel/setup.c:217: error: (Each undeclared identifier is reported only once
arch/microblaze/kernel/setup.c:217: error: for each function it appears in.)
make[1]: *** [arch/microblaze/kernel/setup.o] Error 1
Signed-off-by: Michal Simek <monstr@monstr.eu>
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.
The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Old Microblaze toolchain supported "b" contstrains for
all register but it always points to general purpose reg.
New Microblaze toolchain is more strict in this
and general purpose register should be used there "r".
Signed-off-by: Michal Simek <monstr@monstr.eu>
HZ is more likely to be 1000 these days.
timer handlers are run from softirq, no need to disable bh
skb priority 1 is TC_PRIO_FILLER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two channels here. User space starts counting channels at one
but in the kernel we start at zero. If the user passes in a zero
channel that's invalid and could lead to memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the bug that may prevent from mac to be configured,
while there is an empty slot for it.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add define of SH7734 register and sh_eth_reset_hw_crc function.
V3: Rebase net/HEAD.
V2: Do not split line of #if defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the USB variant of the driver uses usb_make_path in order to
provide bus-info compatible to other USB drivers (like e.g. asix.c).
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".
Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make use of a shared tree setup to limit the confusions on which
tree is current.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch (as1535) fixes a bug in the runtime PM core. When a
runtime suspend attempt completes, whether successfully or not, the
device's power.wait_queue is supposed to be signalled. But this
doesn't happen in the failure pathway of rpm_suspend() when another
autosuspend attempt is rescheduled. As a result, a task can get stuck
indefinitely on the wait queue (I have seen this happen in testing).
The patch fixes the problem by moving the wake_up_all() call up near
the start of the failure code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver
rtl8192ce are reported. One fix (commit a9b89e2) has already been applied,
and it helped, but the maximum RX speed would still drop to 1 Mbps. As in
the previous fix, the initial gain was determined to be the problem; however,
the problem arises from a setting of the gain when scans are started.
Driver rtl8192de also has the same code structure - this one is fixed as well.
Reported-and-Tested-by: Ivan Pesin <ivan.pesin@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I simply don't have any hobby hacking time after family time
and non-kernel-related job time, so I resume status as part-time
mailing list lurker.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Is possible that we will arm the tid_rx->reorder_timer after
del_timer_sync() in ___ieee80211_stop_rx_ba_session(). We need to stop
timer after RCU grace period finish, so move it to
ieee80211_free_tid_rx(). Timer will not be armed again, as
rcu_dereference(sta->ampdu_mlme.tid_rx[tid]) will return NULL.
Debug object detected problem with the following warning:
ODEBUG: free active (active state 0) object type: timer_list hint: sta_rx_agg_reorder_timer_expired+0x0/0xf0 [mac80211]
Bug report (with all warning messages):
https://bugzilla.redhat.com/show_bug.cgi?id=804007
Reported-by: "jan p. springer" <jsd@igroup.org>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another good catch from Jakub Kicinski. This patch fixes my
recent commit: ed61e2b020
"rt2x00: rt2800usb: rework txdone code"
We should reread status register only when nobody else start already
reading status i.e. test_and_set_bit(TX_STATUS_READING, flags) return 0.
Reported-by: Jakub Kicinski <moorray@wp.pl>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is fix for my current commit
ed61e2b020
"rt2x00: rt2800usb: rework txdone code"
We should schedule txdone work on timeout, otherwise if newer get
tx status from hardware, we will never report tx status to mac80211
and eventually never wakeup tx queue.
Reported-by: Jakub Kicinski <moorray@wp.pl>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The on-oper-channel optimization was reverted,
so remove the outdated comment as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station_info struct had demanded dBm signal values, but the
cfg80211 wireless extensions implementation was also accepting
"unspecified" (i.e. RSSI) unit values while the nl80211 code was
completely unaware of them. Resolve this by formally allowing the
"unspecified" units while making nl80211 ignore them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Current commit 0775f9f90c
"mac80211: remove spurious BSSID change flag" exposed bug on iwlegacy,
that we do not set BSSID address correctly and then device was not able
to receive frames after successful associate.
On the way fix scan canceling comment. Apparently ->post_associate()
do cancel scan itself, but scan cancel on BSS_CHANGED_BSSID is needed.
I'm not sure why, but when I removed it, I had frequent auth failures:
wlan4: send auth to 54:e6:fc:98:63:fe (try 1/3)
wlan4: send auth to 54:e6:fc:98:63:fe (try 2/3)
wlan4: send auth to 54:e6:fc:98:63:fe (try 3/3)
wlan4: authentication with 54:e6:fc:98:63:fe timed out
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This il->vif is dereferenced in different part of iwlegacy code, so do
not nullify it. This should fix random crashes observed in companion
with microcode errors i.e. crash in il3945_config_ap().
Additionally this should address also
WARNING: at drivers/net/wireless/iwlegacy/common.c:4656 il_mac_remove_interface
at least one of the possible reasons of that warning.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the xt_set.h header in userspace, one will get these gcc
reports:
ipset/ip_set.h:184:1: error: unknown type name "u16"
In file included from libxt_SET.c:21:0:
netfilter/xt_set.h:61:2: error: unknown type name "u32"
netfilter/xt_set.h:62:2: error: unknown type name "u32"
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
DC[2|5]_HIB_MODE is BIT 12 of DCDC[2|5] Control register.
WM8350_DC2_HIB_MODE_ACTIVE/WM8350_DC2_HIB_MODE_DISABLE are defined as 1/0.
Thus we need to left shift WM8350_DC2_HIB_MODE_SHIFT bits.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want is to restore wm8350->pmic.dcdcx_hib_mode settings to
WM8350_DCDCx_LOW_POWER registers. Current code also clears all other
bits of WM8350_DCDCx_LOW_POWER registers which is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We do not hold a lock while registering regulator, thus should not call unlock
if regulator_register fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At least on ia64 the (bogus) use of xchg() here results in the compiler
warning about an unused expression result. As only an assignment is
intended here, convert it to such.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
According to the datasheet, LDO0 has minimal voltage 1.2V rather than 1.25V.
Table 3-39. VLDO0[2:0] Settings
VLDOx[2:0] VOUT (V) VLDOx[2:0] VOUT (V)
000 1.20 100 2.70
001 1.50 101 2.85
010 1.80 110 3.10
011 2.50 111 3.30
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoids having to duplicate the dependencies of what is 'select'ed (and on
down...)
Those dependencies are currently incomplete, leading to broken builds with
GFS2_FS_LOCKING_DLM=y and IP_SCTP=n.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch fixes the error path of function read_rindex_entry
so that it correctly gives up its glock reference in cases where
there is a race to re-read the rindex after gfs2_grow.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Konrad writes:
I've two small fixes for the xen-blkback - and I think one more will show up
eventually (a partial revert), but not sure when. So in the spirit of keeping
the patches flowing, please git pull the following branch.
They were using the xenbus_dev_fatal() function which would
change the state of the connection immediately. Which is not
what we want when we advertise optional features.
So make 'feature-discard','feature-barrier','feature-flush-cache'
optional.
Suggested-by: Jan Beulich <JBeulich@suse.com>
[v1: Made the discard function void and static]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The only reason for the distinction was for the special case of
'file' (which is assumed to be loopback device), was to reach inside
the loopback device, find the underlaying file, and call fallocate on it.
Fortunately "xen-blkback: convert hole punching to discard request on
loop devices" removes that use-case and we now based the discard
support based on blk_queue_discard(q) and extract all appropriate
parameters from the 'struct request_queue'.
CC: Li Dongyang <lidongyang@novell.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
[v1: Dropping pointless initializer and keeping blank line]
[v2: Remove the kfree as it is not used anymore]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Starting with v3.2 Jonathan reports that Xen crashes loading the ioatdma
driver. A debug run shows:
ioatdma 0000:00:16.4: desc[0]: (0x300cc7000->0x300cc7040) cookie: 0 flags: 0x2 ctl: 0x29 (op: 0 int_en: 1 compl: 1)
...
ioatdma 0000:00:16.4: ioat_get_current_completion: phys_complete: 0xcc7000
...which shows that in this environment GFP_KERNEL memory may be backed
by a 64-bit dma address. This breaks the driver's assumption that an
unsigned long should be able to contain the physical address for
descriptor memory. Switch to dma_addr_t which beyond being the right
size, is the true type for the data i.e. an io-virtual address
inidicating the engine's last processed descriptor.
[stable: 3.2+]
Cc: <stable@vger.kernel.org>
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Reported-by: William Dauchy <wdauchy@gmail.com>
Tested-by: William Dauchy <wdauchy@gmail.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch includes two changes:
* fix incorrect value set for drv_cleanup_done
* re-initialize and start port in mtip_restart_port()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We should use the GFP flags that the caller specified instead of picking
our own. All the callers specify GFP_KERNEL so this doesn't make a
difference to how the kernel runs, it's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On platforms such as OMAP3, certain variants may not have IVA, SGX
or some specific component. We currently have a check to aid fixing
wrong population of OPP entries for issues such as typos. This however
causes a conflict with valid requirement where the SoC variant does
not actually have the module present.
So, reduce the severity of the print to a debug statement and skip
registering that specific OPP, but continue down the list.
Reported-by: Steve Sakoman <steve@sakoman.com>
Reported-by: Maximilian Schwerin <mvs@tigris.de>
Acked-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Maximilian Schwerin <mvs@tigris.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently, pm34xx.c has a mix of printk() and pr_*() statements
so replace the printk() statements with the equivalent pr_*()
statements.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It appears that the error paths were overlooked when the
omap3_pm_init() routine had the prcm chain handler code
added. Fix this by adding a goto target and reordering
the error handling code. Also fix how the irq argument
for free_irq() is determined.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4, recently a synchronisation bug is discovered by hardware
team, which leads to incorrect timer value read from 32K sync timer
IP when the IP is comming out of idle.
The issue is due to the synchronization methodology used in the SYNCTIMER IP.
The value of the counter register in 32kHz domain is synchronized to the OCP
domain register only at count up event, and if the OCP clock is switched off,
the OCP register gets out of synch until the first count up event after the
clock is switched back -at the next falling edge of the 32kHz clock.
Further investigation revealed that it applies to gptimer1 and watchdog timer2
as well which may run on 32KHz. This patch fixes the issue for all the
applicable modules.
The BUG has not made it yet to the OMAP errata list and it is applicable to
OMAP1/2/3/4/5. OMAP1/2/3 it is taken care indirectly by autodeps.
By enabling static depedency of wakeup clockdomain with MPU, as soon as MPU
is woken up from lowpower state(idle) or whenever MPU is active, PRCM forces
the OCP clock to be running and allow the counter value to be updated properly
in the OCP clock domain.
The bug is going to fixed in future OMAP versions.
Reported-Tested-by: dave.long@linaro.org
[dave.long@linaro.org: Reported the oprofile time stamp issue with synctimer
and helped to test this patch]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The total number of scatter gather elements in the CISS command
used by the scsi tape code was being cast to a u8, which can hold
at most 255 scatter gather elements. It should have been cast to
a u16. Without this patch the command gets rejected by the controller
since the total scatter gather count did not add up to the right
value resulting in an i/o error.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The default is too small (1024 blocks), use h->cciss_max_sectors (8192 blocks)
Without this change, if you try to set the block size of a tape drive above
512*1024, via "mt -f /dev/st0 setblk nnn" where nnn is greater than 524288,
it won't work right.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch moves the global blkif_io_lock to the per-device structure. The
spinlock seems to exists for two reasons: to disable IRQs when in the interrupt
handlers for blkfront, and to protect the blkfront VBDs when a detachment is
requested.
Having a global blkif_io_lock doesn't make sense given the use case, and it
drastically hinders performance due to contention. All VBDs with pending IOs
have to take the lock in order to get work done, which serializes everything
pretty badly.
Signed-off-by: Steven Noonan <snoonan@amazon.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We should hang onto bdev until we're done with it.
Signed-off-by: Andrew Jones <drjones@redhat.com>
[v1: Fixed up git commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fix a bug when using 'ethtool -K ethx tx off' to turn off tx ip checksum,
FCoE CRC offload should not be impacte. The skb_checksum_help() is needed
only if it's not FCoE traffic for ip checksum, regardless of ethtool toggling
the tx ip checksum on or off. Instead of using CHECKSUM_PARTIAL, we will
use CHECKSUM_UNNECESSARY as a proper indication to avoid sw ip checksum
on FCoE frames.
Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is related to fixing the bug of dropping FCoE frames when disabling tx ip
checksum by 'ethtool -K ethx tx off'. The FCoE protocol stack driver would
use CHECKSUM_UNNECESSARY on tx path instead of CHECKSUM_PARTIAL (as indicated in
the 2/2 of this series). To do so, netif_needs_gso() has to be changed here to
not do gso for both CHECKSUM_PARTIAL and CHECKSUM_UNNECESSARY.
Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows us to avoid a Tx hang when SR-IOV is enabled. This hang
can be triggered by sending small packets at a rate that was triggering Rx
missed errors from the adapter while the internal Tx switch and at least
one VF are enabled.
This was all due to the fact that under heavy stress the Rx FIFO never
drained below the flow control high water mark. This resulted in the Tx
FIFO being head of line blocked due to the fact that it relies on the flow
control high water mark to determine when it is acceptable for the Tx to
place a packet in the Rx FIFO.
The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so
that even if the ring is almost completely full we can still place Tx
packets on the Rx ring and drop incoming Rx traffic if we do not have
sufficient space available in the Rx FIFO.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previous code used wrong instance for the interrupt register access.
Use the right one which is OCP_SOCKET.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is useful when we have broken type2 compliant IPs' where
the softreset shift is not the same as SYSC_TYPE2_SOFTRESET_SHIFT
and hence is overridden using sysc_fields->srst_shift.
We have at least one such instance now with onchip keypad on OMAP5
which has a different softreset shift as compared to other type2
IPs'.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Balaji TK <balajitk@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Implement ->direct_IO() method in aops. The ->direct_IO() method combines
the existing fuse_direct_read/fuse_direct_write methods to implement
O_DIRECT functionality.
Reaching ->direct_IO() in the read path via generic_file_aio_read ensures
proper synchronization with page cache with its existing framework.
Reaching ->direct_IO() in the write path via fuse_file_aio_write is made
to come via generic_file_direct_write() which makes it play nice with
the page cache w.r.t other mmap pages etc.
On files marked 'direct_io' by the filesystem server, IO always follows
the fuse_direct_read/write path. There is no effect of fcntl(O_DIRECT)
and it always succeeds.
On files not marked with 'direct_io' by the filesystem server, the IO
path depends on O_DIRECT flag by the application. This can be passed
at the time of open() as well as via fcntl().
Note that asynchronous O_DIRECT iocb jobs are completed synchronously
always (this has been the case with FUSE even before this patch)
Signed-off-by: Anand Avati <avati@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Anand Avati reports that the following sequence of system calls fail on a fuse
filesystem:
create("filename") => 0
link("filename", "linkname") => 0
unlink("filename") => 0
link("linkname", "filename") => -ENOENT ### BUG ###
vfs_link() fails with ENOENT if i_nlink is zero, this is done to prevent
resurrecting already deleted files.
Fuse clears i_nlink on unlink even if there are other links pointing to the
file.
Reported-by: Anand Avati <avati@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Adds HSI framework in to the linux kernel.
High Speed Synchronous Serial Interface (HSI) is a
serial interface mainly used for connecting application
engines (APE) with cellular modem engines (CMT) in cellular
handsets.
HSI provides multiplexing for up to 16 logical channels,
low-latency and full duplex communication.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-05 15:42:13 +02:00
1684 changed files with 20301 additions and 11479 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
