Linux 2.6.32-rc4

As reported in

	http://bugzilla.kernel.org/show_bug.cgi?id=13940

on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them.  It then apparently hits some undocumented resource conflict,
resulting in non-working devices.

Try to increase alignment to get more safe range for unassigned devices.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/ABI/testing/sysfs-bus-pci-devices-cciss

@@ -31,3 +31,31 @@ Date:		March 2009
 Kernel Version: 2.6.30
 Contact:	iss_storagedev@hp.com
 Description:	A symbolic link to /sys/block/cciss!cXdY
+
+Where:		/sys/bus/pci/devices/<dev>/ccissX/rescan
+Date:		August 2009
+Kernel Version:	2.6.31
+Contact:	iss_storagedev@hp.com
+Description:	Kicks of a rescan of the controller to discover logical
+		drive topology changes.
+
+Where:		/sys/bus/pci/devices/<dev>/ccissX/cXdY/lunid
+Date:		August 2009
+Kernel Version: 2.6.31
+Contact:	iss_storagedev@hp.com
+Description:	Displays the 8-byte LUN ID used to address logical
+		drive Y of controller X.
+
+Where:		/sys/bus/pci/devices/<dev>/ccissX/cXdY/raid_level
+Date:		August 2009
+Kernel Version: 2.6.31
+Contact:	iss_storagedev@hp.com
+Description:	Displays the RAID level of logical drive Y of
+		controller X.
+
+Where:		/sys/bus/pci/devices/<dev>/ccissX/cXdY/usage_count
+Date:		August 2009
+Kernel Version: 2.6.31
+Contact:	iss_storagedev@hp.com
+Description:	Displays the usage count (number of opens) of logical drive Y
+		of controller X.

Documentation/SubmittingPatches

@@ -232,7 +232,7 @@ your e-mail client so that it sends your patches untouched.
 When sending patches to Linus, always follow step #7.
 
 Large changes are not appropriate for mailing lists, and some
-maintainers.  If your patch, uncompressed, exceeds 40 kB in size,
+maintainers.  If your patch, uncompressed, exceeds 300 kB in size,
 it is preferred that you store your patch on an Internet-accessible
 server, and provide instead a URL (link) pointing to your patch.
 

Documentation/arm/tcm.txt

@@ -29,11 +29,13 @@ TCM location and size. Notice that this is not a MMU table: you
 actually move the physical location of the TCM around. At the
 place you put it, it will mask any underlying RAM from the
 CPU so it is usually wise not to overlap any physical RAM with
-the TCM. The TCM memory exists totally outside the MMU and will
-override any MMU mappings.
+the TCM.
 
-Code executing inside the ITCM does not "see" any MMU mappings
-and e.g. register accesses must be made to physical addresses.
+The TCM memory can then be remapped to another address again using
+the MMU, but notice that the TCM if often used in situations where
+the MMU is turned off. To avoid confusion the current Linux
+implementation will map the TCM 1 to 1 from physical to virtual
+memory in the location specified by the machine.
 
 TCM is used for a few things:
 

Documentation/cgroups/cgroups.txt

@@ -227,7 +227,14 @@ as the path relative to the root of the cgroup file system.
 Each cgroup is represented by a directory in the cgroup file system
 containing the following files describing that cgroup:
 
- - tasks: list of tasks (by pid) attached to that cgroup
+ - tasks: list of tasks (by pid) attached to that cgroup.  This list
+   is not guaranteed to be sorted.  Writing a thread id into this file
+   moves the thread into this cgroup.
+ - cgroup.procs: list of tgids in the cgroup.  This list is not
+   guaranteed to be sorted or free of duplicate tgids, and userspace
+   should sort/uniquify the list if this property is required.
+   Writing a tgid into this file moves all threads with that tgid into
+   this cgroup.
  - notify_on_release flag: run the release agent on exit?
  - release_agent: the path to use for release notifications (this file
    exists in the top cgroup only)
@@ -374,7 +381,7 @@ Now you want to do something with this cgroup.
 
 In this directory you can find several files:
 # ls
-notify_on_release tasks
+cgroup.procs notify_on_release tasks
 (plus whatever files added by the attached subsystems)
 
 Now attach your shell to this cgroup:

Documentation/connector/cn_test.c

@@ -34,7 +34,7 @@ static char cn_test_name[] = "cn_test";
 static struct sock *nls;
 static struct timer_list cn_test_timer;
 
-static void cn_test_callback(struct cn_msg *msg)
+static void cn_test_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
 {
 	pr_info("%s: %lu: idx=%x, val=%x, seq=%u, ack=%u, len=%d: %s.\n",
 	        __func__, jiffies, msg->id.idx, msg->id.val,

Documentation/connector/connector.txt

@@ -23,7 +23,7 @@ handling, etc...  The Connector driver allows any kernelspace agents to use
 netlink based networking for inter-process communication in a significantly
 easier way:
 
-int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
+int cn_add_callback(struct cb_id *id, char *name, void (*callback) (struct cn_msg *, struct netlink_skb_parms *));
 void cn_netlink_send(struct cn_msg *msg, u32 __group, int gfp_mask);
 
 struct cb_id
@@ -53,15 +53,15 @@ struct cn_msg
 Connector interfaces.
 /*****************************************/
 
-int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
+int cn_add_callback(struct cb_id *id, char *name, void (*callback) (struct cn_msg *, struct netlink_skb_parms *));
 
  Registers new callback with connector core.
 
  struct cb_id *id		- unique connector's user identifier.
 				  It must be registered in connector.h for legal in-kernel users.
  char *name			- connector's callback symbolic name.
- void (*callback) (void *)	- connector's callback.
-				  Argument must be dereferenced to struct cn_msg *.
+ void (*callback) (struct cn..)	- connector's callback.
+				  cn_msg and the sender's credentials
 
 
 void cn_del_callback(struct cb_id *id);

Documentation/filesystems/ext4.txt

@@ -282,9 +282,16 @@ stripe=n		Number of filesystem blocks that mballoc will try
 			to use for allocation size and alignment. For RAID5/6
 			systems this should be the number of data
 			disks *  RAID chunk size in file system blocks.
-delalloc	(*)	Deferring block allocation until write-out time.
-nodelalloc		Disable delayed allocation. Blocks are allocation
-			when data is copied from user to page cache.
+
+delalloc	(*)	Defer block allocation until just before ext4
+			writes out the block(s) in question.  This
+			allows ext4 to better allocation decisions
+			more efficiently.
+nodelalloc		Disable delayed allocation.  Blocks are allocated
+			when the data is copied from userspace to the
+			page cache, either via the write(2) system call
+			or when an mmap'ed page which was previously
+			unallocated is written for the first time.
 
 max_batch_time=usec	Maximum amount of time ext4 should wait for
 			additional filesystem operations to be batch

Documentation/filesystems/proc.txt

@@ -1113,7 +1113,6 @@ Table 1-12: Files in /proc/fs/ext4/<devname>
 ..............................................................................
  File            Content                                        
  mb_groups       details of multiblock allocator buddy cache of free blocks
- mb_history      multiblock allocation history
 ..............................................................................
 
 

Documentation/filesystems/vfat.txt

@@ -102,7 +102,7 @@ shortname=lower|win95|winnt|mixed
 		 winnt: emulate the Windows NT rule for display/create.
 		 mixed: emulate the Windows NT rule for display,
 			emulate the Windows 95 rule for create.
-		 Default setting is `lower'.
+		 Default setting is `mixed'.
 
 tz=UTC        -- Interpret timestamps as UTC rather than local time.
                  This option disables the conversion of timestamps

Documentation/hwmon/ltc4215

@@ -22,12 +22,13 @@ Usage Notes
 -----------
 
 This driver does not probe for LTC4215 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
 
 Example: the following will load the driver for an LTC4215 at address 0x44
 on I2C bus #0:
-$ modprobe ltc4215 force=0,0x44
+$ modprobe ltc4215
+$ echo ltc4215 0x44 > /sys/bus/i2c/devices/i2c-0/new_device
 
 
 Sysfs entries

Documentation/hwmon/ltc4245

@@ -23,12 +23,13 @@ Usage Notes
 -----------
 
 This driver does not probe for LTC4245 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
 
 Example: the following will load the driver for an LTC4245 at address 0x23
 on I2C bus #1:
-$ modprobe ltc4245 force=1,0x23
+$ modprobe ltc4245
+$ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device
 
 
 Sysfs entries

Documentation/i2c/instantiating-devices

@@ -188,7 +188,7 @@ segment, the address is sufficient to uniquely identify the device to be
 deleted.
 
 Example:
-# echo eeprom 0x50 > /sys/class/i2c-adapter/i2c-3/new_device
+# echo eeprom 0x50 > /sys/bus/i2c/devices/i2c-3/new_device
 
 While this interface should only be used when in-kernel device declaration
 can't be done, there is a variety of cases where it can be helpful:

Documentation/infiniband/user_mad.txt

@@ -128,8 +128,8 @@ Setting IsSM Capability Bit
   To create the appropriate character device files automatically with
   udev, a rule like
 
-    KERNEL="umad*", NAME="infiniband/%k"
-    KERNEL="issm*", NAME="infiniband/%k"
+    KERNEL=="umad*", NAME="infiniband/%k"
+    KERNEL=="issm*", NAME="infiniband/%k"
 
   can be used.  This will create device nodes named
 

Documentation/infiniband/user_verbs.txt

@@ -58,7 +58,7 @@ Memory pinning
   To create the appropriate character device files automatically with
   udev, a rule like
 
-    KERNEL="uverbs*", NAME="infiniband/%k"
+    KERNEL=="uverbs*", NAME="infiniband/%k"
 
   can be used.  This will create device nodes named
 

Documentation/isdn/INTERFACE.CAPI

@@ -60,10 +60,9 @@ open() operation on regular files or character devices.
 
 After a successful return from register_appl(), CAPI messages from the
 application may be passed to the driver for the device via calls to the
-send_message() callback function. The CAPI message to send is stored in the
-data portion of an skb. Conversely, the driver may call Kernel CAPI's
-capi_ctr_handle_message() function to pass a received CAPI message to Kernel
-CAPI for forwarding to an application, specifying its ApplID.
+send_message() callback function. Conversely, the driver may call Kernel
+CAPI's capi_ctr_handle_message() function to pass a received CAPI message to
+Kernel CAPI for forwarding to an application, specifying its ApplID.
 
 Deregistration requests (CAPI operation CAPI_RELEASE) from applications are
 forwarded as calls to the release_appl() callback function, passing the same
@@ -142,6 +141,7 @@ u16  (*send_message)(struct capi_ctr *ctrlr, struct sk_buff *skb)
 	to accepting or queueing the message. Errors occurring during the
 	actual processing of the message should be signaled with an
 	appropriate reply message.
+	May be called in process or interrupt context.
 	Calls to this function are not serialized by Kernel CAPI, ie. it must
 	be prepared to be re-entered.
 
@@ -154,7 +154,8 @@ read_proc_t *ctr_read_proc
 	system entry, /proc/capi/controllers/<n>; will be called with a
 	pointer to the device's capi_ctr structure as the last (data) argument
 
-Note: Callback functions are never called in interrupt context.
+Note: Callback functions except send_message() are never called in interrupt
+context.
 
 - to be filled in before calling capi_ctr_ready():
 
@@ -171,14 +172,40 @@ u8 serial[CAPI_SERIAL_LEN]
 	value to return for CAPI_GET_SERIAL
 
 
-4.3 The _cmsg Structure
+4.3 SKBs
+
+CAPI messages are passed between Kernel CAPI and the driver via send_message()
+and capi_ctr_handle_message(), stored in the data portion of a socket buffer
+(skb).  Each skb contains a single CAPI message coded according to the CAPI 2.0
+standard.
+
+For the data transfer messages, DATA_B3_REQ and DATA_B3_IND, the actual
+payload data immediately follows the CAPI message itself within the same skb.
+The Data and Data64 parameters are not used for processing. The Data64
+parameter may be omitted by setting the length field of the CAPI message to 22
+instead of 30.
+
+
+4.4 The _cmsg Structure
 
 (declared in <linux/isdn/capiutil.h>)
 
 The _cmsg structure stores the contents of a CAPI 2.0 message in an easily
-accessible form. It contains members for all possible CAPI 2.0 parameters, of
-which only those appearing in the message type currently being processed are
-actually used. Unused members should be set to zero.
+accessible form. It contains members for all possible CAPI 2.0 parameters,
+including subparameters of the Additional Info and B Protocol structured
+parameters, with the following exceptions:
+
+* second Calling party number (CONNECT_IND)
+
+* Data64 (DATA_B3_REQ and DATA_B3_IND)
+
+* Sending complete (subparameter of Additional Info, CONNECT_REQ and INFO_REQ)
+
+* Global Configuration (subparameter of B Protocol, CONNECT_REQ, CONNECT_RESP
+  and SELECT_B_PROTOCOL_REQ)
+
+Only those parameters appearing in the message type currently being processed
+are actually used. Unused members should be set to zero.
 
 Members are named after the CAPI 2.0 standard names of the parameters they
 represent. See <linux/isdn/capiutil.h> for the exact spelling. Member data
@@ -190,18 +217,19 @@ u16         for CAPI parameters of type 'word'
 
 u32         for CAPI parameters of type 'dword'
 
-_cstruct    for CAPI parameters of type 'struct' not containing any
-	    variably-sized (struct) subparameters (eg. 'Called Party Number')
+_cstruct    for CAPI parameters of type 'struct'
 	    The member is a pointer to a buffer containing the parameter in
 	    CAPI encoding (length + content). It may also be NULL, which will
 	    be taken to represent an empty (zero length) parameter.
+	    Subparameters are stored in encoded form within the content part.
 
-_cmstruct   for CAPI parameters of type 'struct' containing 'struct'
-	    subparameters ('Additional Info' and 'B Protocol')
+_cmstruct   alternative representation for CAPI parameters of type 'struct'
+	    (used only for the 'Additional Info' and 'B Protocol' parameters)
 	    The representation is a single byte containing one of the values:
-	    CAPI_DEFAULT: the parameter is empty
-	    CAPI_COMPOSE: the values of the subparameters are stored
-	    individually in the corresponding _cmsg structure members
+	    CAPI_DEFAULT: The parameter is empty/absent.
+	    CAPI_COMPOSE: The parameter is present.
+	    Subparameter values are stored individually in the corresponding
+	    _cmsg structure members.
 
 Functions capi_cmsg2message() and capi_message2cmsg() are provided to convert
 messages between their transport encoding described in the CAPI 2.0 standard
@@ -297,3 +325,26 @@ char *capi_cmd2str(u8 Command, u8 Subcommand)
 	be NULL if the command/subcommand is not one of those defined in the
 	CAPI 2.0 standard.
 
+
+7. Debugging
+
+The module kernelcapi has a module parameter showcapimsgs controlling some
+debugging output produced by the module. It can only be set when the module is
+loaded, via a parameter "showcapimsgs=<n>" to the modprobe command, either on
+the command line or in the configuration file.
+
+If the lowest bit of showcapimsgs is set, kernelcapi logs controller and
+application up and down events.
+
+In addition, every registered CAPI controller has an associated traceflag
+parameter controlling how CAPI messages sent from and to tha controller are
+logged. The traceflag parameter is initialized with the value of the
+showcapimsgs parameter when the controller is registered, but can later be
+changed via the MANUFACTURER_REQ command KCAPI_CMD_TRACE.
+
+If the value of traceflag is non-zero, CAPI messages are logged.
+DATA_B3 messages are only logged if the value of traceflag is > 2.
+
+If the lowest bit of traceflag is set, only the command/subcommand and message
+length are logged. Otherwise, kernelcapi logs a readable representation of
+the entire message.

Documentation/kernel-parameters.txt

@@ -671,6 +671,7 @@ and is between 256 and 4096 characters. It is defined in the file
 	earlyprintk=	[X86,SH,BLACKFIN]
 			earlyprintk=vga
 			earlyprintk=serial[,ttySn[,baudrate]]
+			earlyprintk=ttySn[,baudrate]
 			earlyprintk=dbgp[debugController#]
 
 			Append ",keep" to not disable it when the real console

Documentation/misc-devices/max6875

@@ -42,10 +42,12 @@ General Remarks
 
 Valid addresses for the MAX6875 are 0x50 and 0x52.
 Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56.
-The driver does not probe any address, so you must force the address.
+The driver does not probe any address, so you explicitly instantiate the
+devices.
 
 Example:
-$ modprobe max6875 force=0,0x50
+$ modprobe max6875
+$ echo max6875 0x50 > /sys/bus/i2c/devices/i2c-0/new_device
 
 The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple
 addresses.  For example, for address 0x50, it also reserves 0x51.

Documentation/networking/pktgen.txt

@@ -90,6 +90,11 @@ Examples:
  pgset "dstmac 00:00:00:00:00:00"    sets MAC destination address
  pgset "srcmac 00:00:00:00:00:00"    sets MAC source address
 
+ pgset "queue_map_min 0" Sets the min value of tx queue interval
+ pgset "queue_map_max 7" Sets the max value of tx queue interval, for multiqueue devices
+                         To select queue 1 of a given device,
+                         use queue_map_min=1 and queue_map_max=1
+
  pgset "src_mac_count 1" Sets the number of MACs we'll range through.  
                          The 'minimum' MAC is what you set with srcmac.
 
@@ -101,6 +106,9 @@ Examples:
                               IPDST_RND, UDPSRC_RND,
                               UDPDST_RND, MACSRC_RND, MACDST_RND 
                               MPLS_RND, VID_RND, SVID_RND
+                              QUEUE_MAP_RND # queue map random
+                              QUEUE_MAP_CPU # queue map mirrors smp_processor_id()
+
 
  pgset "udp_src_min 9"   set UDP source port min, If < udp_src_max, then
                          cycle through the port range.

Documentation/networking/timestamping/timestamping.c

@@ -381,7 +381,7 @@ int main(int argc, char **argv)
 	memset(&hwtstamp, 0, sizeof(hwtstamp));
 	strncpy(hwtstamp.ifr_name, interface, sizeof(hwtstamp.ifr_name));
 	hwtstamp.ifr_data = (void *)&hwconfig;
-	memset(&hwconfig, 0, sizeof(&hwconfig));
+	memset(&hwconfig, 0, sizeof(hwconfig));
 	hwconfig.tx_type =
 		(so_timestamping_flags & SOF_TIMESTAMPING_TX_HARDWARE) ?
 		HWTSTAMP_TX_ON : HWTSTAMP_TX_OFF;

Documentation/scsi/hptiop.txt

@@ -3,6 +3,25 @@ HIGHPOINT ROCKETRAID 3xxx/4xxx ADAPTER DRIVER (hptiop)
 Controller Register Map
 -------------------------
 
+For RR44xx Intel IOP based adapters, the controller IOP is accessed via PCI BAR0 and BAR2:
+
+     BAR0 offset    Register
+            0x11C5C Link Interface IRQ Set
+            0x11C60 Link Interface IRQ Clear
+
+     BAR2 offset    Register
+            0x10    Inbound Message Register 0
+            0x14    Inbound Message Register 1
+            0x18    Outbound Message Register 0
+            0x1C    Outbound Message Register 1
+            0x20    Inbound Doorbell Register
+            0x24    Inbound Interrupt Status Register
+            0x28    Inbound Interrupt Mask Register
+            0x30    Outbound Interrupt Status Register
+            0x34    Outbound Interrupt Mask Register
+            0x40    Inbound Queue Port
+            0x44    Outbound Queue Port
+
 For Intel IOP based adapters, the controller IOP is accessed via PCI BAR0:
 
      BAR0 offset    Register
@@ -93,7 +112,7 @@ The driver exposes following sysfs attributes:
 
 
 -----------------------------------------------------------------------------
-Copyright (C) 2006-2007 HighPoint Technologies, Inc. All Rights Reserved.
+Copyright (C) 2006-2009 HighPoint Technologies, Inc. All Rights Reserved.
 
   This file is distributed in the hope that it will be useful,
   but WITHOUT ANY WARRANTY; without even the implied warranty of

Documentation/sound/alsa/HD-Audio-Models.txt

@@ -209,6 +209,7 @@ AD1884A / AD1883 / AD1984A / AD1984B
   laptop	laptop with HP jack sensing
   mobile	mobile devices with HP jack sensing
   thinkpad	Lenovo Thinkpad X300
+  touchsmart	HP Touchsmart
 
 AD1884
 ======

Documentation/vm/ksm.txt

@@ -52,15 +52,15 @@ The KSM daemon is controlled by sysfs files in /sys/kernel/mm/ksm/,
 readable by all but writable only by root:
 
 max_kernel_pages - set to maximum number of kernel pages that KSM may use
-                   e.g. "echo 2000 > /sys/kernel/mm/ksm/max_kernel_pages"
+                   e.g. "echo 100000 > /sys/kernel/mm/ksm/max_kernel_pages"
                    Value 0 imposes no limit on the kernel pages KSM may use;
                    but note that any process using MADV_MERGEABLE can cause
                    KSM to allocate these pages, unswappable until it exits.
-                   Default: 2000 (chosen for demonstration purposes)
+                   Default: quarter of memory (chosen to not pin too much)
 
 pages_to_scan    - how many present pages to scan before ksmd goes to sleep
-                   e.g. "echo 200 > /sys/kernel/mm/ksm/pages_to_scan"
-                   Default: 200 (chosen for demonstration purposes)
+                   e.g. "echo 100 > /sys/kernel/mm/ksm/pages_to_scan"
+                   Default: 100 (chosen for demonstration purposes)
 
 sleep_millisecs  - how many milliseconds ksmd should sleep before next scan
                    e.g. "echo 20 > /sys/kernel/mm/ksm/sleep_millisecs"
@@ -70,7 +70,8 @@ run              - set 0 to stop ksmd from running but keep merged pages,
                    set 1 to run ksmd e.g. "echo 1 > /sys/kernel/mm/ksm/run",
                    set 2 to stop ksmd and unmerge all pages currently merged,
                          but leave mergeable areas registered for next run
-                   Default: 1 (for immediate use by apps which register)
+                   Default: 0 (must be changed to 1 to activate KSM,
+                               except if CONFIG_SYSFS is disabled)
 
 The effectiveness of KSM and MADV_MERGEABLE is shown in /sys/kernel/mm/ksm/:
 
@@ -86,4 +87,4 @@ pages_volatile embraces several different kinds of activity, but a high
 proportion there would also indicate poor use of madvise MADV_MERGEABLE.
 
 Izik Eidus,
-Hugh Dickins, 30 July 2009
+Hugh Dickins, 24 Sept 2009

Documentation/vm/page-types.c

@@ -2,7 +2,10 @@
  * page-types: Tool for querying page flags
  *
  * Copyright (C) 2009 Intel corporation
- * Copyright (C) 2009 Wu Fengguang <fengguang.wu@intel.com>
+ *
+ * Authors: Wu Fengguang <fengguang.wu@intel.com>
+ *
+ * Released under the General Public License (GPL).
  */
 
 #define _LARGEFILE64_SOURCE
@@ -69,7 +72,9 @@
 #define KPF_COMPOUND_TAIL	16
 #define KPF_HUGE		17
 #define KPF_UNEVICTABLE		18
+#define KPF_HWPOISON		19
 #define KPF_NOPAGE		20
+#define KPF_KSM			21
 
 /* [32-] kernel hacking assistances */
 #define KPF_RESERVED		32
@@ -116,7 +121,9 @@ static char *page_flag_names[] = {
 	[KPF_COMPOUND_TAIL]	= "T:compound_tail",
 	[KPF_HUGE]		= "G:huge",
 	[KPF_UNEVICTABLE]	= "u:unevictable",
+	[KPF_HWPOISON]		= "X:hwpoison",
 	[KPF_NOPAGE]		= "n:nopage",
+	[KPF_KSM]		= "x:ksm",
 
 	[KPF_RESERVED]		= "r:reserved",
 	[KPF_MLOCKED]		= "m:mlocked",
@@ -152,9 +159,6 @@ static unsigned long	opt_size[MAX_ADDR_RANGES];
 static int		nr_vmas;
 static unsigned long	pg_start[MAX_VMAS];
 static unsigned long	pg_end[MAX_VMAS];
-static unsigned long	voffset;
-
-static int		pagemap_fd;
 
 #define MAX_BIT_FILTERS	64
 static int		nr_bit_filters;
@@ -163,9 +167,16 @@ static uint64_t		opt_bits[MAX_BIT_FILTERS];
 
 static int		page_size;
 
-#define PAGES_BATCH	(64 << 10)	/* 64k pages */
+static int		pagemap_fd;
 static int		kpageflags_fd;
 
+static int		opt_hwpoison;
+static int		opt_unpoison;
+
+static char		*hwpoison_debug_fs = "/debug/hwpoison";
+static int		hwpoison_inject_fd;
+static int		hwpoison_forget_fd;
+
 #define HASH_SHIFT	13
 #define HASH_SIZE	(1 << HASH_SHIFT)
 #define HASH_MASK	(HASH_SIZE - 1)
@@ -207,6 +218,74 @@ static void fatal(const char *x, ...)
 	exit(EXIT_FAILURE);
 }
 
+int checked_open(const char *pathname, int flags)
+{
+	int fd = open(pathname, flags);
+
+	if (fd < 0) {
+		perror(pathname);
+		exit(EXIT_FAILURE);
+	}
+
+	return fd;
+}
+
+/*
+ * pagemap/kpageflags routines
+ */
+
+static unsigned long do_u64_read(int fd, char *name,
+				 uint64_t *buf,
+				 unsigned long index,
+				 unsigned long count)
+{
+	long bytes;
+
+	if (index > ULONG_MAX / 8)
+		fatal("index overflow: %lu\n", index);
+
+	if (lseek(fd, index * 8, SEEK_SET) < 0) {
+		perror(name);
+		exit(EXIT_FAILURE);
+	}
+
+	bytes = read(fd, buf, count * 8);
+	if (bytes < 0) {
+		perror(name);
+		exit(EXIT_FAILURE);
+	}
+	if (bytes % 8)
+		fatal("partial read: %lu bytes\n", bytes);
+
+	return bytes / 8;
+}
+
+static unsigned long kpageflags_read(uint64_t *buf,
+				     unsigned long index,
+				     unsigned long pages)
+{
+	return do_u64_read(kpageflags_fd, PROC_KPAGEFLAGS, buf, index, pages);
+}
+
+static unsigned long pagemap_read(uint64_t *buf,
+				  unsigned long index,
+				  unsigned long pages)
+{
+	return do_u64_read(pagemap_fd, "/proc/pid/pagemap", buf, index, pages);
+}
+
+static unsigned long pagemap_pfn(uint64_t val)
+{
+	unsigned long pfn;
+
+	if (val & PM_PRESENT)
+		pfn = PM_PFRAME(val);
+	else
+		pfn = 0;
+
+	return pfn;
+}
+
 
 /*
  * page flag names
@@ -255,7 +334,8 @@ static char *page_flag_longname(uint64_t flags)
  * page list and summary
  */
 
-static void show_page_range(unsigned long offset, uint64_t flags)
+static void show_page_range(unsigned long voffset,
+			    unsigned long offset, uint64_t flags)
 {
 	static uint64_t      flags0;
 	static unsigned long voff;
@@ -281,7 +361,8 @@ static void show_page_range(unsigned long offset, uint64_t flags)
 	count  = 1;
 }
 
-static void show_page(unsigned long offset, uint64_t flags)
+static void show_page(unsigned long voffset,
+		      unsigned long offset, uint64_t flags)
 {
 	if (opt_pid)
 		printf("%lx\t", voffset);
@@ -362,6 +443,62 @@ static uint64_t well_known_flags(uint64_t flags)
 	return flags;
 }
 
+static uint64_t kpageflags_flags(uint64_t flags)
+{
+	flags = expand_overloaded_flags(flags);
+
+	if (!opt_raw)
+		flags = well_known_flags(flags);
+
+	return flags;
+}
+
+/*
+ * page actions
+ */
+
+static void prepare_hwpoison_fd(void)
+{
+	char buf[100];
+
+	if (opt_hwpoison && !hwpoison_inject_fd) {
+		sprintf(buf, "%s/corrupt-pfn", hwpoison_debug_fs);
+		hwpoison_inject_fd = checked_open(buf, O_WRONLY);
+	}
+
+	if (opt_unpoison && !hwpoison_forget_fd) {
+		sprintf(buf, "%s/renew-pfn", hwpoison_debug_fs);
+		hwpoison_forget_fd = checked_open(buf, O_WRONLY);
+	}
+}
+
+static int hwpoison_page(unsigned long offset)
+{
+	char buf[100];
+	int len;
+
+	len = sprintf(buf, "0x%lx\n", offset);
+	len = write(hwpoison_inject_fd, buf, len);
+	if (len < 0) {
+		perror("hwpoison inject");
+		return len;
+	}
+	return 0;
+}
+
+static int unpoison_page(unsigned long offset)
+{
+	char buf[100];
+	int len;
+
+	len = sprintf(buf, "0x%lx\n", offset);
+	len = write(hwpoison_forget_fd, buf, len);
+	if (len < 0) {
+		perror("hwpoison forget");
+		return len;
+	}
+	return 0;
+}
 
 /*
  * page frame walker
@@ -394,104 +531,83 @@ static int hash_slot(uint64_t flags)
 	exit(EXIT_FAILURE);
 }
 
-static void add_page(unsigned long offset, uint64_t flags)
+static void add_page(unsigned long voffset,
+		     unsigned long offset, uint64_t flags)
 {
-	flags = expand_overloaded_flags(flags);
-
-	if (!opt_raw)
-		flags = well_known_flags(flags);
+	flags = kpageflags_flags(flags);
 
 	if (!bit_mask_ok(flags))
 		return;
 
+	if (opt_hwpoison)
+		hwpoison_page(offset);
+	if (opt_unpoison)
+		unpoison_page(offset);
+
 	if (opt_list == 1)
-		show_page_range(offset, flags);
+		show_page_range(voffset, offset, flags);
 	else if (opt_list == 2)
-		show_page(offset, flags);
+		show_page(voffset, offset, flags);
 
 	nr_pages[hash_slot(flags)]++;
 	total_pages++;
 }
 
-static void walk_pfn(unsigned long index, unsigned long count)
+#define KPAGEFLAGS_BATCH	(64 << 10)	/* 64k pages */
+static void walk_pfn(unsigned long voffset,
+		     unsigned long index,
+		     unsigned long count)
 {
+	uint64_t buf[KPAGEFLAGS_BATCH];
 	unsigned long batch;
-	unsigned long n;
+	unsigned long pages;
 	unsigned long i;
 
-	if (index > ULONG_MAX / KPF_BYTES)
-		fatal("index overflow: %lu\n", index);
-
-	lseek(kpageflags_fd, index * KPF_BYTES, SEEK_SET);
-
 	while (count) {
-		uint64_t kpageflags_buf[KPF_BYTES * PAGES_BATCH];
-
-		batch = min_t(unsigned long, count, PAGES_BATCH);
-		n = read(kpageflags_fd, kpageflags_buf, batch * KPF_BYTES);
-		if (n == 0)
+		batch = min_t(unsigned long, count, KPAGEFLAGS_BATCH);
+		pages = kpageflags_read(buf, index, batch);
+		if (pages == 0)
 			break;
-		if (n < 0) {
-			perror(PROC_KPAGEFLAGS);
-			exit(EXIT_FAILURE);
-		}
 
-		if (n % KPF_BYTES != 0)
-			fatal("partial read: %lu bytes\n", n);
-		n = n / KPF_BYTES;
+		for (i = 0; i < pages; i++)
+			add_page(voffset + i, index + i, buf[i]);
 
-		for (i = 0; i < n; i++)
-			add_page(index + i, kpageflags_buf[i]);
-
-		index += batch;
-		count -= batch;
+		index += pages;
+		count -= pages;
 	}
 }
 
-
-#define PAGEMAP_BATCH	4096
-static unsigned long task_pfn(unsigned long pgoff)
+#define PAGEMAP_BATCH	(64 << 10)
+static void walk_vma(unsigned long index, unsigned long count)
 {
-	static uint64_t buf[PAGEMAP_BATCH];
-	static unsigned long start;
-	static long count;
-	uint64_t pfn;
+	uint64_t buf[PAGEMAP_BATCH];
+	unsigned long batch;
+	unsigned long pages;
+	unsigned long pfn;
+	unsigned long i;
 
-	if (pgoff < start || pgoff >= start + count) {
-		if (lseek64(pagemap_fd,
-			    (uint64_t)pgoff * PM_ENTRY_BYTES,
-			    SEEK_SET) < 0) {
-			perror("pagemap seek");
-			exit(EXIT_FAILURE);
+	while (count) {
+		batch = min_t(unsigned long, count, PAGEMAP_BATCH);
+		pages = pagemap_read(buf, index, batch);
+		if (pages == 0)
+			break;
+
+		for (i = 0; i < pages; i++) {
+			pfn = pagemap_pfn(buf[i]);
+			if (pfn)
+				walk_pfn(index + i, pfn, 1);
 		}
-		count = read(pagemap_fd, buf, sizeof(buf));
-		if (count == 0)
-			return 0;
-		if (count < 0) {
-			perror("pagemap read");
-			exit(EXIT_FAILURE);
-		}
-		if (count % PM_ENTRY_BYTES) {
-			fatal("pagemap read not aligned.\n");
-			exit(EXIT_FAILURE);
-		}
-		count /= PM_ENTRY_BYTES;
-		start = pgoff;
+
+		index += pages;
+		count -= pages;
 	}
-
-	pfn = buf[pgoff - start];
-	if (pfn & PM_PRESENT)
-		pfn = PM_PFRAME(pfn);
-	else
-		pfn = 0;
-
-	return pfn;
 }
 
 static void walk_task(unsigned long index, unsigned long count)
 {
-	int i = 0;
 	const unsigned long end = index + count;
+	unsigned long start;
+	int i = 0;
 
 	while (index < end) {
 
@@ -501,15 +617,11 @@ static void walk_task(unsigned long index, unsigned long count)
 		if (pg_start[i] >= end)
 			return;
 
-		voffset = max_t(unsigned long, pg_start[i], index);
-		index   = min_t(unsigned long, pg_end[i], end);
+		start = max_t(unsigned long, pg_start[i], index);
+		index = min_t(unsigned long, pg_end[i], end);
 
-		assert(voffset < index);
-		for (; voffset < index; voffset++) {
-			unsigned long pfn = task_pfn(voffset);
-			if (pfn)
-				walk_pfn(pfn, 1);
-		}
+		assert(start < index);
+		walk_vma(start, index - start);
 	}
 }
 
@@ -527,18 +639,14 @@ static void walk_addr_ranges(void)
 {
 	int i;
 
-	kpageflags_fd = open(PROC_KPAGEFLAGS, O_RDONLY);
-	if (kpageflags_fd < 0) {
-		perror(PROC_KPAGEFLAGS);
-		exit(EXIT_FAILURE);
-	}
+	kpageflags_fd = checked_open(PROC_KPAGEFLAGS, O_RDONLY);
 
 	if (!nr_addr_ranges)
 		add_addr_range(0, ULONG_MAX);
 
 	for (i = 0; i < nr_addr_ranges; i++)
 		if (!opt_pid)
-			walk_pfn(opt_offset[i], opt_size[i]);
+			walk_pfn(0, opt_offset[i], opt_size[i]);
 		else
 			walk_task(opt_offset[i], opt_size[i]);
 
@@ -575,6 +683,8 @@ static void usage(void)
 "            -l|--list                 Show page details in ranges\n"
 "            -L|--list-each            Show page details one by one\n"
 "            -N|--no-summary           Don't show summay info\n"
+"            -X|--hwpoison             hwpoison pages\n"
+"            -x|--unpoison             unpoison pages\n"
 "            -h|--help                 Show this usage message\n"
 "addr-spec:\n"
 "            N                         one page at offset N (unit: pages)\n"
@@ -624,11 +734,7 @@ static void parse_pid(const char *str)
 	opt_pid = parse_number(str);
 
 	sprintf(buf, "/proc/%d/pagemap", opt_pid);
-	pagemap_fd = open(buf, O_RDONLY);
-	if (pagemap_fd < 0) {
-		perror(buf);
-		exit(EXIT_FAILURE);
-	}
+	pagemap_fd = checked_open(buf, O_RDONLY);
 
 	sprintf(buf, "/proc/%d/maps", opt_pid);
 	file = fopen(buf, "r");
@@ -788,6 +894,8 @@ static struct option opts[] = {
 	{ "list"      , 0, NULL, 'l' },
 	{ "list-each" , 0, NULL, 'L' },
 	{ "no-summary", 0, NULL, 'N' },
+	{ "hwpoison"  , 0, NULL, 'X' },
+	{ "unpoison"  , 0, NULL, 'x' },
 	{ "help"      , 0, NULL, 'h' },
 	{ NULL        , 0, NULL, 0 }
 };
@@ -799,7 +907,7 @@ int main(int argc, char *argv[])
 	page_size = getpagesize();
 
 	while ((c = getopt_long(argc, argv,
-				"rp:f:a:b:lLNh", opts, NULL)) != -1) {
+				"rp:f:a:b:lLNXxh", opts, NULL)) != -1) {
 		switch (c) {
 		case 'r':
 			opt_raw = 1;
@@ -825,6 +933,14 @@ int main(int argc, char *argv[])
 		case 'N':
 			opt_no_summary = 1;
 			break;
+		case 'X':
+			opt_hwpoison = 1;
+			prepare_hwpoison_fd();
+			break;
+		case 'x':
+			opt_unpoison = 1;
+			prepare_hwpoison_fd();
+			break;
 		case 'h':
 			usage();
 			exit(0);
@@ -844,7 +960,7 @@ int main(int argc, char *argv[])
 	walk_addr_ranges();
 
 	if (opt_list == 1)
-		show_page_range(0, 0);  /* drain the buffer */
+		show_page_range(0, 0, 0);  /* drain the buffer */
 
 	if (opt_no_summary)
 		return 0;

Documentation/vm/pagemap.txt

@@ -57,7 +57,9 @@ There are three components to pagemap:
     16. COMPOUND_TAIL
     16. HUGE
     18. UNEVICTABLE
+    19. HWPOISON
     20. NOPAGE
+    21. KSM
 
 Short descriptions to the page flags:
 
@@ -86,9 +88,15 @@ Short descriptions to the page flags:
 17. HUGE
     this is an integral part of a HugeTLB page
 
+19. HWPOISON
+    hardware detected memory corruption on this page: don't touch the data!
+
 20. NOPAGE
     no page frame exists at the requested address
 
+21. KSM
+    identical memory pages dynamically shared between one or more processes
+
     [IO related page flags]
  1. ERROR     IO error occurred
  3. UPTODATE  page has up-to-date data

Documentation/w1/masters/ds2482

@@ -24,8 +24,8 @@ General Remarks
 
 Valid addresses are 0x18, 0x19, 0x1a, and 0x1b.
 However, the device cannot be detected without writing to the i2c bus, so no
-detection is done.
-You should force the device address.
+detection is done. You should instantiate the device explicitly.
 
-$ modprobe ds2482 force=0,0x18
+$ modprobe ds2482
+$ echo ds2482 0x18 > /sys/bus/i2c/devices/i2c-0/new_device
 

MAINTAINERS

@@ -257,6 +257,13 @@ W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/acpi/fan.c
 
+ACPI PROCESSOR AGGREGATOR DRIVER
+M:	Shaohua Li <shaohua.li@intel.com>
+L:	linux-acpi@vger.kernel.org
+W:	http://www.lesswatts.org/projects/acpi/
+S:	Supported
+F:	drivers/acpi/acpi_pad.c
+
 ACPI THERMAL DRIVER
 M:	Zhang Rui <rui.zhang@intel.com>
 L:	linux-acpi@vger.kernel.org
@@ -646,24 +653,24 @@ ARM/INTEL IOP32X ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IOP33X ARM ARCHITECTURE
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IOP13XX ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IQ81342EX MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IXP2000 ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -691,7 +698,7 @@ ARM/INTEL XSC3 (MANZANO) ARM CORE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/IP FABRICS DOUBLE ESPRESSO MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -741,23 +748,36 @@ M:	Dirk Opfer <dirk@opfer-online.de>
 S:	Maintained
 
 ARM/PALMTX,PALMT5,PALMLD,PALMTE2,PALMTC SUPPORT
-P:	Marek Vasut
-M:	marek.vasut@gmail.com
+M:	Marek Vasut <marek.vasut@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
+F:	arch/arm/mach-pxa/include/mach/palmtx.h
+F:	arch/arm/mach-pxa/palmtx.c
+F:	arch/arm/mach-pxa/include/mach/palmt5.h
+F:	arch/arm/mach-pxa/palmt5.c
+F:	arch/arm/mach-pxa/include/mach/palmld.h
+F:	arch/arm/mach-pxa/palmld.c
+F:	arch/arm/mach-pxa/include/mach/palmte2.h
+F:	arch/arm/mach-pxa/palmte2.c
+F:	arch/arm/mach-pxa/include/mach/palmtc.h
+F:	arch/arm/mach-pxa/palmtc.c
 
 ARM/PALM TREO 680 SUPPORT
 M:	Tomas Cech <sleep_walker@suse.cz>
 L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
+F:	arch/arm/mach-pxa/include/mach/treo680.h
+F:	arch/arm/mach-pxa/treo680.c
 
 ARM/PALMZ72 SUPPORT
 M:	Sergey Lapin <slapin@ossfans.org>
 L:	linux-arm-kernel@lists.infradead.org
 W:	http://hackndev.com
 S:	Maintained
+F:	arch/arm/mach-pxa/include/mach/palmz72.h
+F:	arch/arm/mach-pxa/palmz72.c
 
 ARM/PLEB SUPPORT
 M:	Peter Chubb <pleb@gelato.unsw.edu.au>
@@ -1211,6 +1231,13 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/tg3.*
 
+BROCADE BFA FC SCSI DRIVER
+P:      Jing Huang
+M:      huangj@brocade.com
+L:      linux-scsi@vger.kernel.org
+S:      Supported
+F:      drivers/scsi/bfa/
+
 BSG (block layer generic sg v4 driver)
 M:	FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
 L:	linux-scsi@vger.kernel.org
@@ -2038,7 +2065,7 @@ S:	Maintained
 F:	fs/*
 
 FINTEK F75375S HARDWARE MONITOR AND FAN CONTROLLER DRIVER
-M:	Riku Voipio <riku.vipio@iki.fi>
+M:	Riku Voipio <riku.voipio@iki.fi>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/f75375s.c
@@ -2682,7 +2709,7 @@ F:	include/linux/intel-iommu.h
 
 INTEL IOP-ADMA DMA DRIVER
 M:	Dan Williams <dan.j.williams@intel.com>
-S:	Supported
+S:	Maintained
 F:	drivers/dma/iop-adma.c
 
 INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT
@@ -3623,6 +3650,13 @@ F:	Documentation/blockdev/nbd.txt
 F:	drivers/block/nbd.c
 F:	include/linux/nbd.h
 
+NETWORK DROP MONITOR
+M:	Neil Horman <nhorman@tuxdriver.com>
+L:	netdev@vger.kernel.org
+S:	Maintained
+W:	https://fedorahosted.org/dropwatch/
+F:	net/core/drop_monitor.c
+
 NETWORKING [GENERAL]
 M:	"David S. Miller" <davem@davemloft.net>
 L:	netdev@vger.kernel.org
@@ -3953,6 +3987,7 @@ F:	drivers/block/paride/
 PARISC ARCHITECTURE
 M:	Kyle McMartin <kyle@mcmartin.ca>
 M:	Helge Deller <deller@gmx.de>
+M:	"James E.J. Bottomley" <jejb@parisc-linux.org>
 L:	linux-parisc@vger.kernel.org
 W:	http://www.parisc-linux.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.git
@@ -4618,6 +4653,14 @@ F:	drivers/ata/
 F:	include/linux/ata.h
 F:	include/linux/libata.h
 
+SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
+P:     Jayamohan Kallickal
+M:     jayamohank@serverengines.com
+L:     linux-scsi@vger.kernel.org
+W:     http://www.serverengines.com
+S:     Supported
+F:     drivers/scsi/be2iscsi/
+
 SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
 M:	Sathya Perla <sathyap@serverengines.com>
 M:	Subbu Seetharaman <subbus@serverengines.com>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 32
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc4
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*

arch/arm/common/sa1111.c

@@ -1032,6 +1032,7 @@ unsigned int sa1111_pll_clock(struct sa1111_dev *sadev)
 
 	return __sa1111_pll_clock(sachip);
 }
+EXPORT_SYMBOL(sa1111_pll_clock);
 
 /**
  *	sa1111_select_audio_mode - select I2S or AC link mode
@@ -1059,6 +1060,7 @@ void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode)
 
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_select_audio_mode);
 
 /**
  *	sa1111_set_audio_rate - set the audio sample rate
@@ -1083,6 +1085,7 @@ int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate)
 
 	return 0;
 }
+EXPORT_SYMBOL(sa1111_set_audio_rate);
 
 /**
  *	sa1111_get_audio_rate - get the audio sample rate
@@ -1100,6 +1103,7 @@ int sa1111_get_audio_rate(struct sa1111_dev *sadev)
 
 	return __sa1111_pll_clock(sachip) / (256 * div);
 }
+EXPORT_SYMBOL(sa1111_get_audio_rate);
 
 void sa1111_set_io_dir(struct sa1111_dev *sadev,
 		       unsigned int bits, unsigned int dir,
@@ -1128,6 +1132,7 @@ void sa1111_set_io_dir(struct sa1111_dev *sadev,
 	MODIFY_BITS(gpio + SA1111_GPIO_PCSDR, (bits >> 16) & 255, sleep_dir >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_io_dir);
 
 void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 {
@@ -1142,6 +1147,7 @@ void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 	MODIFY_BITS(gpio + SA1111_GPIO_PCDWR, (bits >> 16) & 255, v >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_io);
 
 void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 {
@@ -1156,6 +1162,7 @@ void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned i
 	MODIFY_BITS(gpio + SA1111_GPIO_PCSSR, (bits >> 16) & 255, v >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_sleep_io);
 
 /*
  * Individual device operations.
@@ -1176,6 +1183,7 @@ void sa1111_enable_device(struct sa1111_dev *sadev)
 	sa1111_writel(val | sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_enable_device);
 
 /**
  *	sa1111_disable_device - disable an on-chip SA1111 function block
@@ -1192,6 +1200,7 @@ void sa1111_disable_device(struct sa1111_dev *sadev)
 	sa1111_writel(val & ~sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_disable_device);
 
 /*
  *	SA1111 "Register Access Bus."
@@ -1259,17 +1268,20 @@ struct bus_type sa1111_bus_type = {
 	.suspend	= sa1111_bus_suspend,
 	.resume		= sa1111_bus_resume,
 };
+EXPORT_SYMBOL(sa1111_bus_type);
 
 int sa1111_driver_register(struct sa1111_driver *driver)
 {
 	driver->drv.bus = &sa1111_bus_type;
 	return driver_register(&driver->drv);
 }
+EXPORT_SYMBOL(sa1111_driver_register);
 
 void sa1111_driver_unregister(struct sa1111_driver *driver)
 {
 	driver_unregister(&driver->drv);
 }
+EXPORT_SYMBOL(sa1111_driver_unregister);
 
 static int __init sa1111_init(void)
 {
@@ -1290,16 +1302,3 @@ module_exit(sa1111_exit);
 
 MODULE_DESCRIPTION("Intel Corporation SA1111 core driver");
 MODULE_LICENSE("GPL");
-
-EXPORT_SYMBOL(sa1111_select_audio_mode);
-EXPORT_SYMBOL(sa1111_set_audio_rate);
-EXPORT_SYMBOL(sa1111_get_audio_rate);
-EXPORT_SYMBOL(sa1111_set_io_dir);
-EXPORT_SYMBOL(sa1111_set_io);
-EXPORT_SYMBOL(sa1111_set_sleep_io);
-EXPORT_SYMBOL(sa1111_enable_device);
-EXPORT_SYMBOL(sa1111_disable_device);
-EXPORT_SYMBOL(sa1111_pll_clock);
-EXPORT_SYMBOL(sa1111_bus_type);
-EXPORT_SYMBOL(sa1111_driver_register);
-EXPORT_SYMBOL(sa1111_driver_unregister);

arch/arm/configs/h3600_defconfig

@@ -90,7 +90,6 @@ CONFIG_ARCH_SA1100=y
 # CONFIG_SA1100_COLLIE is not set
 # CONFIG_SA1100_H3100 is not set
 CONFIG_SA1100_H3600=y
-CONFIG_SA1100_H3XXX=y
 # CONFIG_SA1100_BADGE4 is not set
 # CONFIG_SA1100_JORNADA720 is not set
 # CONFIG_SA1100_HACKKIT is not set

arch/arm/include/asm/glue.h

@@ -120,25 +120,39 @@
 #endif
 
 /*
- * Prefetch abort handler.  If the CPU has an IFAR use that, otherwise
- * use the address of the aborted instruction
+ *	Prefetch Abort Model
+ *	================
+ *
+ *	We have the following to choose from:
+ *	  legacy	- no IFSR, no IFAR
+ *	  v6		- ARMv6: IFSR, no IFAR
+ *	  v7		- ARMv7: IFSR and IFAR
  */
+
 #undef CPU_PABORT_HANDLER
 #undef MULTI_PABORT
 
-#ifdef CONFIG_CPU_PABRT_IFAR
+#ifdef CONFIG_CPU_PABRT_LEGACY
 # ifdef CPU_PABORT_HANDLER
 #  define MULTI_PABORT 1
 # else
-#  define CPU_PABORT_HANDLER(reg, insn)	mrc p15, 0, reg, cr6, cr0, 2
+#  define CPU_PABORT_HANDLER legacy_pabort
 # endif
 #endif
 
-#ifdef CONFIG_CPU_PABRT_NOIFAR
+#ifdef CONFIG_CPU_PABRT_V6
 # ifdef CPU_PABORT_HANDLER
 #  define MULTI_PABORT 1
 # else
-#  define CPU_PABORT_HANDLER(reg, insn)	mov reg, insn
+#  define CPU_PABORT_HANDLER v6_pabort
+# endif
+#endif
+
+#ifdef CONFIG_CPU_PABRT_V7
+# ifdef CPU_PABORT_HANDLER
+#  define MULTI_PABORT 1
+# else
+#  define CPU_PABORT_HANDLER v7_pabort
 # endif
 #endif
 

arch/arm/include/asm/hardware/iop3xx.h

@@ -215,6 +215,7 @@ extern int iop3xx_get_init_atu(void);
  * IOP3XX I/O and Mem space regions for PCI autoconfiguration
  */
 #define IOP3XX_PCI_LOWER_MEM_PA	0x80000000
+#define IOP3XX_PCI_MEM_WINDOW_SIZE	0x08000000
 
 #define IOP3XX_PCI_IO_WINDOW_SIZE	0x00010000
 #define IOP3XX_PCI_LOWER_IO_PA		0x90000000

arch/arm/include/asm/smp_plat.h

@@ -0,0 +1,16 @@
+/*
+ * ARM specific SMP header, this contains our implementation
+ * details.
+ */
+#ifndef __ASMARM_SMP_PLAT_H
+#define __ASMARM_SMP_PLAT_H
+
+#include <asm/cputype.h>
+
+/* all SMP configurations have the extended CPUID registers */
+static inline int tlb_ops_need_broadcast(void)
+{
+	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
+}
+
+#endif

arch/arm/include/asm/unistd.h

@@ -456,6 +456,7 @@
  * Unimplemented (or alternatively implemented) syscalls
  */
 #define __IGNORE_fadvise64_64		1
+#define __IGNORE_migrate_pages		1
 
 #endif /* __KERNEL__ */
 #endif /* __ASM_ARM_UNISTD_H */

arch/arm/kernel/entry-armv.S

@@ -311,22 +311,16 @@ __pabt_svc:
 	tst	r3, #PSR_I_BIT
 	biceq	r9, r9, #PSR_I_BIT
 
-	@
-	@ set args, then call main handler
-	@
-	@  r0 - address of faulting instruction
-	@  r1 - pointer to registers on stack
-	@
-#ifdef MULTI_PABORT
 	mov	r0, r2			@ pass address of aborted instruction.
+#ifdef MULTI_PABORT
 	ldr	r4, .LCprocfns
 	mov	lr, pc
 	ldr	pc, [r4, #PROCESSOR_PABT_FUNC]
 #else
-	CPU_PABORT_HANDLER(r0, r2)
+	bl	CPU_PABORT_HANDLER
 #endif
 	msr	cpsr_c, r9			@ Maybe enable interrupts
-	mov	r1, sp				@ regs
+	mov	r2, sp				@ regs
 	bl	do_PrefetchAbort		@ call abort handler
 
 	@
@@ -701,16 +695,16 @@ ENDPROC(__und_usr_unknown)
 __pabt_usr:
 	usr_entry
 
-#ifdef MULTI_PABORT
 	mov	r0, r2			@ pass address of aborted instruction.
+#ifdef MULTI_PABORT
 	ldr	r4, .LCprocfns
 	mov	lr, pc
 	ldr	pc, [r4, #PROCESSOR_PABT_FUNC]
 #else
-	CPU_PABORT_HANDLER(r0, r2)
+	bl	CPU_PABORT_HANDLER
 #endif
 	enable_irq				@ Enable interrupts
-	mov	r1, sp				@ regs
+	mov	r2, sp				@ regs
 	bl	do_PrefetchAbort		@ call abort handler
  UNWIND(.fnend		)
 	/* fall through */

arch/arm/kernel/entry-common.S

@@ -126,7 +126,7 @@ ENTRY(__gnu_mcount_nc)
 	cmp r0, r2
 	bne gnu_trace
 	ldmia sp!, {r0-r3, ip, lr}
-	bx ip
+	mov pc, ip
 
 gnu_trace:
 	ldr r1, [sp, #20]			@ lr of instrumented routine
@@ -135,7 +135,7 @@ gnu_trace:
 	mov lr, pc
 	mov pc, r2
 	ldmia sp!, {r0-r3, ip, lr}
-	bx ip
+	mov pc, ip
 
 ENTRY(mcount)
 	stmdb sp!, {r0-r3, lr}
@@ -425,13 +425,6 @@ sys_mmap2:
 #endif
 ENDPROC(sys_mmap2)
 
-ENTRY(pabort_ifar)
-		mrc	p15, 0, r0, cr6, cr0, 2
-ENTRY(pabort_noifar)
-		mov	pc, lr
-ENDPROC(pabort_ifar)
-ENDPROC(pabort_noifar)
-
 #ifdef CONFIG_OABI_COMPAT
 
 /*

arch/arm/kernel/head-common.S

@@ -13,6 +13,7 @@
 
 #define ATAG_CORE 0x54410001
 #define ATAG_CORE_SIZE ((2*4 + 3*4) >> 2)
+#define ATAG_CORE_SIZE_EMPTY ((2*4) >> 2)
 
 	.align	2
 	.type	__switch_data, %object
@@ -251,7 +252,8 @@ __vet_atags:
 	bne	1f
 
 	ldr	r5, [r2, #0]			@ is first tag ATAG_CORE?
-	subs	r5, r5, #ATAG_CORE_SIZE
+	cmp	r5, #ATAG_CORE_SIZE
+	cmpne	r5, #ATAG_CORE_SIZE_EMPTY
 	bne	1f
 	ldr	r5, [r2, #4]
 	ldr	r6, =ATAG_CORE

arch/arm/kernel/smp.c

@@ -36,6 +36,7 @@
 #include <asm/tlbflush.h>
 #include <asm/ptrace.h>
 #include <asm/localtimer.h>
+#include <asm/smp_plat.h>
 
 /*
  * as from 2.5, kernels no longer have an init_tasks structure
@@ -153,7 +154,7 @@ int __cpuinit __cpu_up(unsigned int cpu)
 /*
  * __cpu_disable runs on the processor to be shutdown.
  */
-int __cpuexit __cpu_disable(void)
+int __cpu_disable(void)
 {
 	unsigned int cpu = smp_processor_id();
 	struct task_struct *p;
@@ -200,7 +201,7 @@ int __cpuexit __cpu_disable(void)
  * called on the thread which is asking for a CPU to be shutdown -
  * waits until shutdown has completed, or it is timed out.
  */
-void __cpuexit __cpu_die(unsigned int cpu)
+void __cpu_die(unsigned int cpu)
 {
 	if (!platform_cpu_kill(cpu))
 		printk("CPU%u: unable to kill\n", cpu);
@@ -214,7 +215,7 @@ void __cpuexit __cpu_die(unsigned int cpu)
  * of the other hotplug-cpu capable cores, so presumably coming
  * out of idle fixes this.
  */
-void __cpuexit cpu_die(void)
+void __ref cpu_die(void)
 {
 	unsigned int cpu = smp_processor_id();
 
@@ -586,12 +587,6 @@ struct tlb_args {
 	unsigned long ta_end;
 };
 
-/* all SMP configurations have the extended CPUID registers */
-static inline int tlb_ops_need_broadcast(void)
-{
-	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
-}
-
 static inline void ipi_flush_tlb_all(void *ignored)
 {
 	local_flush_tlb_all();

arch/arm/kernel/smp_twd.c

@@ -166,10 +166,12 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 	clockevents_register_device(clk);
 }
 
+#ifdef CONFIG_HOTPLUG_CPU
 /*
  * take a local timer down
  */
-void __cpuexit twd_timer_stop(void)
+void twd_timer_stop(void)
 {
 	__raw_writel(0, twd_base + TWD_TIMER_CONTROL);
 }
+#endif

arch/arm/kernel/time.c

@@ -21,6 +21,7 @@
 #include <linux/interrupt.h>
 #include <linux/time.h>
 #include <linux/init.h>
+#include <linux/sched.h>
 #include <linux/smp.h>
 #include <linux/timex.h>
 #include <linux/errno.h>

arch/arm/kernel/traps.c

@@ -418,12 +418,14 @@ static int bad_syscall(int n, struct pt_regs *regs)
 static inline void
 do_cache_op(unsigned long start, unsigned long end, int flags)
 {
+	struct mm_struct *mm = current->active_mm;
 	struct vm_area_struct *vma;
 
 	if (end < start || flags)
 		return;
 
-	vma = find_vma(current->active_mm, start);
+	down_read(&mm->mmap_sem);
+	vma = find_vma(mm, start);
 	if (vma && vma->vm_start < end) {
 		if (start < vma->vm_start)
 			start = vma->vm_start;
@@ -432,6 +434,7 @@ do_cache_op(unsigned long start, unsigned long end, int flags)
 
 		flush_cache_user_range(vma, start, end);
 	}
+	up_read(&mm->mmap_sem);
 }
 
 /*

arch/arm/mach-bcmring/core.c

@@ -31,7 +31,6 @@
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 
-#include <linux/amba/bus.h>
 #include <mach/csp/mm_addr.h>
 #include <mach/hardware.h>
 #include <asm/clkdev.h>
@@ -45,7 +44,6 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 
 #include <cfg_global.h>
 

arch/arm/mach-davinci/board-dm365-evm.c

@@ -35,7 +35,6 @@
 #include <mach/common.h>
 #include <mach/i2c.h>
 #include <mach/serial.h>
-#include <mach/common.h>
 #include <mach/mmc.h>
 #include <mach/nand.h>
 

arch/arm/mach-integrator/pci_v3.c

@@ -31,6 +31,7 @@
 
 #include <mach/hardware.h>
 #include <asm/irq.h>
+#include <asm/signal.h>
 #include <asm/system.h>
 #include <asm/mach/pci.h>
 #include <asm/irq_regs.h>
@@ -486,7 +487,7 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys)
 	return ret;
 }
 
-struct pci_bus *pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
+struct pci_bus * __init pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
 {
 	return pci_scan_bus(sys->busnr, &pci_v3_ops, sys);
 }

arch/arm/mach-iop32x/include/mach/iop32x.h

@@ -31,7 +31,5 @@
 #define IOP32X_MAX_RAM_SIZE            0x40000000UL
 #define IOP3XX_MAX_RAM_SIZE            IOP32X_MAX_RAM_SIZE
 #define IOP3XX_PCI_LOWER_MEM_BA        0x80000000
-#define IOP32X_PCI_MEM_WINDOW_SIZE     0x04000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE     IOP32X_PCI_MEM_WINDOW_SIZE
 
 #endif

arch/arm/mach-iop33x/include/mach/iop33x.h

@@ -36,8 +36,6 @@
 #define IOP33X_MAX_RAM_SIZE		0x80000000UL
 #define IOP3XX_MAX_RAM_SIZE		IOP33X_MAX_RAM_SIZE
 #define IOP3XX_PCI_LOWER_MEM_BA	(PHYS_OFFSET + IOP33X_MAX_RAM_SIZE)
-#define IOP33X_PCI_MEM_WINDOW_SIZE	0x08000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE	IOP33X_PCI_MEM_WINDOW_SIZE
 
 
 #endif

arch/arm/mach-ns9xxx/clock.c

@@ -195,7 +195,7 @@ static int clk_debugfs_open(struct inode *inode, struct file *file)
 	return single_open(file, clk_debugfs_show, NULL);
 }
 
-static struct file_operations clk_debugfs_operations = {
+static const struct file_operations clk_debugfs_operations = {
 	.open = clk_debugfs_open,
 	.read = seq_read,
 	.llseek = seq_lseek,

arch/arm/mach-omap1/id.c

@@ -38,7 +38,7 @@ static struct omap_id omap_ids[] __initdata = {
 	{ .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000},
 	{ .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100},
 	{ .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300},
-	{ .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320500, .type = 0x08500000},
+	{ .jtag_id = 0xb62c, .die_rev = 0x1, .omap_id = 0x03320500, .type = 0x08500000},
 	{ .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000},
 	{ .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x16100000},
 	{ .jtag_id = 0xb576, .die_rev = 0x2, .omap_id = 0x03320100, .type = 0x16110000},

arch/arm/mach-omap2/board-3430sdp.c

@@ -54,7 +54,7 @@
 
 #define TWL4030_MSECURE_GPIO 22
 
-static int sdp3430_keymap[] = {
+static int board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_RIGHT),
 	KEY(0, 2, KEY_A),
@@ -88,11 +88,15 @@ static int sdp3430_keymap[] = {
 	0
 };
 
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
 static struct twl4030_keypad_data sdp3430_kp_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 5,
 	.cols		= 6,
-	.keymap		= sdp3430_keymap,
-	.keymapsize	= ARRAY_SIZE(sdp3430_keymap),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/board-ldp.c

@@ -80,7 +80,7 @@ static struct platform_device ldp_smsc911x_device = {
 	},
 };
 
-static int ldp_twl4030_keymap[] = {
+static int board_keymap[] = {
 	KEY(0, 0, KEY_1),
 	KEY(1, 0, KEY_2),
 	KEY(2, 0, KEY_3),
@@ -101,11 +101,15 @@ static int ldp_twl4030_keymap[] = {
 	0
 };
 
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
 static struct twl4030_keypad_data ldp_kp_twl4030_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 6,
 	.cols		= 6,
-	.keymap		= ldp_twl4030_keymap,
-	.keymapsize	= ARRAY_SIZE(ldp_twl4030_keymap),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/board-omap3beagle.c

@@ -139,8 +139,13 @@ static struct gpio_led gpio_leds[];
 static int beagle_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
+	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+		omap_cfg_reg(AG9_34XX_GPIO23);
+		mmc[0].gpio_wp = 23;
+	} else {
+		omap_cfg_reg(AH8_34XX_GPIO29);
+	}
 	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	omap_cfg_reg(AH8_34XX_GPIO29);
 	mmc[0].gpio_cd = gpio + 0;
 	twl4030_mmc_init(mmc);
 

arch/arm/mach-omap2/board-omap3evm.c

@@ -159,7 +159,7 @@ static struct twl4030_usb_data omap3evm_usb_data = {
 	.usb_mode	= T2_USB_MODE_ULPI,
 };
 
-static int omap3evm_keymap[] = {
+static int board_keymap[] = {
 	KEY(0, 0, KEY_LEFT),
 	KEY(0, 1, KEY_RIGHT),
 	KEY(0, 2, KEY_A),
@@ -178,11 +178,15 @@ static int omap3evm_keymap[] = {
 	KEY(3, 3, KEY_P)
 };
 
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
 static struct twl4030_keypad_data omap3evm_kp_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 4,
 	.cols		= 4,
-	.keymap		= omap3evm_keymap,
-	.keymapsize	= ARRAY_SIZE(omap3evm_keymap),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/board-omap3pandora.c

@@ -133,7 +133,7 @@ static void __init pandora_keys_gpio_init(void)
 	omap_set_gpio_debounce_time(32 * 5, GPIO_DEBOUNCE_TIME);
 }
 
-static int pandora_keypad_map[] = {
+static int board_keymap[] = {
 	/* col, row, code */
 	KEY(0, 0, KEY_9),
 	KEY(0, 1, KEY_0),
@@ -180,11 +180,15 @@ static int pandora_keypad_map[] = {
 	KEY(5, 2, KEY_FN),
 };
 
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
 static struct twl4030_keypad_data pandora_kp_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 8,
 	.cols		= 6,
-	.keymap		= pandora_keypad_map,
-	.keymapsize	= ARRAY_SIZE(pandora_keypad_map),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -36,58 +36,62 @@
 #define SYSTEM_REV_B_USES_VAUX3	0x1699
 #define SYSTEM_REV_S_USES_VAUX3 0x8
 
-static int rx51_keymap[] = {
+static int board_keymap[] = {
 	KEY(0, 0, KEY_Q),
-	KEY(0, 1, KEY_W),
-	KEY(0, 2, KEY_E),
-	KEY(0, 3, KEY_R),
-	KEY(0, 4, KEY_T),
-	KEY(0, 5, KEY_Y),
-	KEY(0, 6, KEY_U),
-	KEY(0, 7, KEY_I),
-	KEY(1, 0, KEY_O),
+	KEY(0, 1, KEY_O),
+	KEY(0, 2, KEY_P),
+	KEY(0, 3, KEY_COMMA),
+	KEY(0, 4, KEY_BACKSPACE),
+	KEY(0, 6, KEY_A),
+	KEY(0, 7, KEY_S),
+	KEY(1, 0, KEY_W),
 	KEY(1, 1, KEY_D),
-	KEY(1, 2, KEY_DOT),
-	KEY(1, 3, KEY_V),
-	KEY(1, 4, KEY_DOWN),
-	KEY(2, 0, KEY_P),
-	KEY(2, 1, KEY_F),
+	KEY(1, 2, KEY_F),
+	KEY(1, 3, KEY_G),
+	KEY(1, 4, KEY_H),
+	KEY(1, 5, KEY_J),
+	KEY(1, 6, KEY_K),
+	KEY(1, 7, KEY_L),
+	KEY(2, 0, KEY_E),
+	KEY(2, 1, KEY_DOT),
 	KEY(2, 2, KEY_UP),
-	KEY(2, 3, KEY_B),
-	KEY(2, 4, KEY_RIGHT),
-	KEY(3, 0, KEY_COMMA),
-	KEY(3, 1, KEY_G),
-	KEY(3, 2, KEY_ENTER),
+	KEY(2, 3, KEY_ENTER),
+	KEY(2, 5, KEY_Z),
+	KEY(2, 6, KEY_X),
+	KEY(2, 7, KEY_C),
+	KEY(3, 0, KEY_R),
+	KEY(3, 1, KEY_V),
+	KEY(3, 2, KEY_B),
 	KEY(3, 3, KEY_N),
-	KEY(4, 0, KEY_BACKSPACE),
-	KEY(4, 1, KEY_H),
-	KEY(4, 3, KEY_M),
+	KEY(3, 4, KEY_M),
+	KEY(3, 5, KEY_SPACE),
+	KEY(3, 6, KEY_SPACE),
+	KEY(3, 7, KEY_LEFT),
+	KEY(4, 0, KEY_T),
+	KEY(4, 1, KEY_DOWN),
+	KEY(4, 2, KEY_RIGHT),
 	KEY(4, 4, KEY_LEFTCTRL),
-	KEY(5, 1, KEY_J),
-	KEY(5, 2, KEY_Z),
-	KEY(5, 3, KEY_SPACE),
-	KEY(5, 4, KEY_LEFTSHIFT),
-	KEY(6, 0, KEY_A),
-	KEY(6, 1, KEY_K),
-	KEY(6, 2, KEY_X),
-	KEY(6, 3, KEY_SPACE),
-	KEY(6, 4, KEY_FN),
-	KEY(7, 0, KEY_S),
-	KEY(7, 1, KEY_L),
-	KEY(7, 2, KEY_C),
-	KEY(7, 3, KEY_LEFT),
-	KEY(0xff, 0, KEY_F6),
-	KEY(0xff, 1, KEY_F7),
-	KEY(0xff, 2, KEY_F8),
-	KEY(0xff, 4, KEY_F9),
-	KEY(0xff, 5, KEY_F10),
+	KEY(4, 5, KEY_RIGHTALT),
+	KEY(4, 6, KEY_LEFTSHIFT),
+	KEY(5, 0, KEY_Y),
+	KEY(6, 0, KEY_U),
+	KEY(7, 0, KEY_I),
+	KEY(7, 1, KEY_F7),
+	KEY(7, 2, KEY_F8),
+	KEY(0xff, 2, KEY_F9),
+	KEY(0xff, 4, KEY_F10),
+	KEY(0xff, 5, KEY_F11),
+};
+
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
 };
 
 static struct twl4030_keypad_data rx51_kp_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 8,
 	.cols		= 8,
-	.keymap		= rx51_keymap,
-	.keymapsize	= ARRAY_SIZE(rx51_keymap),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/board-zoom2.c

@@ -27,7 +27,7 @@
 #include "mmc-twl4030.h"
 
 /* Zoom2 has Qwerty keyboard*/
-static int zoom2_twl4030_keymap[] = {
+static int board_keymap[] = {
 	KEY(0, 0, KEY_E),
 	KEY(1, 0, KEY_R),
 	KEY(2, 0, KEY_T),
@@ -82,11 +82,15 @@ static int zoom2_twl4030_keymap[] = {
 	0
 };
 
+static struct matrix_keymap_data board_map_data = {
+	.keymap			= board_keymap,
+	.keymap_size		= ARRAY_SIZE(board_keymap),
+};
+
 static struct twl4030_keypad_data zoom2_kp_twl4030_data = {
+	.keymap_data	= &board_map_data,
 	.rows		= 8,
 	.cols		= 8,
-	.keymap		= zoom2_twl4030_keymap,
-	.keymapsize	= ARRAY_SIZE(zoom2_twl4030_keymap),
 	.rep		= 1,
 };
 

arch/arm/mach-omap2/clock34xx.c

@@ -338,6 +338,13 @@ static struct omap_clk omap34xx_clks[] = {
  */
 #define SDRC_MPURATE_LOOPS		96
 
+/*
+ * DPLL5_FREQ_FOR_USBHOST: USBHOST and USBTLL are the only clocks
+ * that are sourced by DPLL5, and both of these require this clock
+ * to be at 120 MHz for proper operation.
+ */
+#define DPLL5_FREQ_FOR_USBHOST		120000000
+
 /**
  * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI
  * @clk: struct clk * being enabled
@@ -1056,6 +1063,28 @@ void omap2_clk_prepare_for_reboot(void)
 #endif
 }
 
+static void omap3_clk_lock_dpll5(void)
+{
+	struct clk *dpll5_clk;
+	struct clk *dpll5_m2_clk;
+
+	dpll5_clk = clk_get(NULL, "dpll5_ck");
+	clk_set_rate(dpll5_clk, DPLL5_FREQ_FOR_USBHOST);
+	clk_enable(dpll5_clk);
+
+	/* Enable autoidle to allow it to enter low power bypass */
+	omap3_dpll_allow_idle(dpll5_clk);
+
+	/* Program dpll5_m2_clk divider for no division */
+	dpll5_m2_clk = clk_get(NULL, "dpll5_m2_ck");
+	clk_enable(dpll5_m2_clk);
+	clk_set_rate(dpll5_m2_clk, DPLL5_FREQ_FOR_USBHOST);
+
+	clk_disable(dpll5_m2_clk);
+	clk_disable(dpll5_clk);
+	return;
+}
+
 /* REVISIT: Move this init stuff out into clock.c */
 
 /*
@@ -1148,6 +1177,12 @@ int __init omap2_clk_init(void)
 	 */
 	clk_enable_init_clocks();
 
+	/*
+	 * Lock DPLL5 and put it in autoidle.
+	 */
+	if (omap_rev() >= OMAP3430_REV_ES2_0)
+		omap3_clk_lock_dpll5();
+
 	/* Avoid sleeping during omap2_clk_prepare_for_reboot() */
 	/* REVISIT: not yet ready for 343x */
 #if 0

arch/arm/mach-omap2/cm4xxx.c

@@ -22,7 +22,6 @@
 #include <asm/atomic.h>
 
 #include "cm.h"
-#include "cm-regbits-4xxx.h"
 
 /* XXX move this to cm.h */
 /* MAX_MODULE_READY_TIME: max milliseconds for module to leave idle */
@@ -50,19 +49,7 @@
  */
 int omap4_cm_wait_idlest_ready(u32 prcm_mod, u8 prcm_dev_offs)
 {
-	int i = 0;
-	u8 cm_id;
-	u16 prcm_mod_offs;
-	u32 mask = OMAP4_PRCM_CM_CLKCTRL_IDLEST_MASK;
-
-	cm_id = prcm_mod >> OMAP4_PRCM_MOD_CM_ID_SHIFT;
-	prcm_mod_offs = prcm_mod & OMAP4_PRCM_MOD_OFFS_MASK;
-
-	while (((omap4_cm_read_mod_reg(cm_id, prcm_mod_offs, prcm_dev_offs,
-				       OMAP4_CM_CLKCTRL_DREG) & mask) != 0) &&
-	       (i++ < MAX_MODULE_READY_TIME))
-		udelay(1);
-
-	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+	/* FIXME: Add clock manager related code */
+	return 0;
 }
 

arch/arm/mach-omap2/devices.c

@@ -355,29 +355,60 @@ static struct platform_device omap2_mcspi4 = {
 };
 #endif
 
-static void omap_init_mcspi(void)
+#ifdef CONFIG_ARCH_OMAP4
+static inline void omap4_mcspi_fixup(void)
 {
-	if (cpu_is_omap44xx()) {
-		omap2_mcspi1_resources[0].start	= OMAP4_MCSPI1_BASE;
-		omap2_mcspi1_resources[0].end	= OMAP4_MCSPI1_BASE + 0xff;
-		omap2_mcspi2_resources[0].start	= OMAP4_MCSPI2_BASE;
-		omap2_mcspi2_resources[0].end	= OMAP4_MCSPI2_BASE + 0xff;
-		omap2_mcspi3_resources[0].start	= OMAP4_MCSPI3_BASE;
-		omap2_mcspi3_resources[0].end	= OMAP4_MCSPI3_BASE + 0xff;
-		omap2_mcspi4_resources[0].start	= OMAP4_MCSPI4_BASE;
-		omap2_mcspi4_resources[0].end	= OMAP4_MCSPI4_BASE + 0xff;
-	}
-	platform_device_register(&omap2_mcspi1);
-	platform_device_register(&omap2_mcspi2);
+	omap2_mcspi1_resources[0].start	= OMAP4_MCSPI1_BASE;
+	omap2_mcspi1_resources[0].end	= OMAP4_MCSPI1_BASE + 0xff;
+	omap2_mcspi2_resources[0].start	= OMAP4_MCSPI2_BASE;
+	omap2_mcspi2_resources[0].end	= OMAP4_MCSPI2_BASE + 0xff;
+	omap2_mcspi3_resources[0].start	= OMAP4_MCSPI3_BASE;
+	omap2_mcspi3_resources[0].end	= OMAP4_MCSPI3_BASE + 0xff;
+	omap2_mcspi4_resources[0].start	= OMAP4_MCSPI4_BASE;
+	omap2_mcspi4_resources[0].end	= OMAP4_MCSPI4_BASE + 0xff;
+}
+#else
+static inline void omap4_mcspi_fixup(void)
+{
+}
+#endif
+
 #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
 	defined(CONFIG_ARCH_OMAP4)
-	if (cpu_is_omap2430() || cpu_is_omap343x() || cpu_is_omap44xx())
-		platform_device_register(&omap2_mcspi3);
+static inline void omap2_mcspi3_init(void)
+{
+	platform_device_register(&omap2_mcspi3);
+}
+#else
+static inline void omap2_mcspi3_init(void)
+{
+}
 #endif
+
 #if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
-	if (cpu_is_omap343x() || cpu_is_omap44xx())
-		platform_device_register(&omap2_mcspi4);
+static inline void omap2_mcspi4_init(void)
+{
+	platform_device_register(&omap2_mcspi4);
+}
+#else
+static inline void omap2_mcspi4_init(void)
+{
+}
 #endif
+
+static void omap_init_mcspi(void)
+{
+	if (cpu_is_omap44xx())
+		omap4_mcspi_fixup();
+
+	platform_device_register(&omap2_mcspi1);
+	platform_device_register(&omap2_mcspi2);
+
+	if (cpu_is_omap2430() || cpu_is_omap343x() || cpu_is_omap44xx())
+		omap2_mcspi3_init();
+
+	if (cpu_is_omap343x() || cpu_is_omap44xx())
+		omap2_mcspi4_init();
 }
 
 #else

arch/arm/mach-omap2/io.c

@@ -294,10 +294,10 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
 	else if (cpu_is_omap34xx())
 		hwmods = omap34xx_hwmods;
 
-	omap_hwmod_init(hwmods);
-	omap2_mux_init();
 #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
 	/* The OPP tables have to be registered before a clk init */
+	omap_hwmod_init(hwmods);
+	omap2_mux_init();
 	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);

arch/arm/mach-omap2/iommu2.c

@@ -79,7 +79,7 @@ static int omap2_iommu_enable(struct iommu *obj)
 		l = iommu_read_reg(obj, MMU_SYSSTATUS);
 		if (l & MMU_SYS_RESETDONE)
 			break;
-	} while (time_after(jiffies, timeout));
+	} while (!time_after(jiffies, timeout));
 
 	if (!(l & MMU_SYS_RESETDONE)) {
 		dev_err(obj->dev, "can't take mmu out of reset\n");

arch/arm/mach-omap2/mailbox.c

@@ -30,6 +30,14 @@
 #define MAILBOX_IRQ_NEWMSG(u)		(1 << (2 * (u)))
 #define MAILBOX_IRQ_NOTFULL(u)		(1 << (2 * (u) + 1))
 
+/* SYSCONFIG: register bit definition */
+#define AUTOIDLE	(1 << 0)
+#define SOFTRESET	(1 << 1)
+#define SMARTIDLE	(2 << 3)
+
+/* SYSSTATUS: register bit definition */
+#define RESETDONE	(1 << 0)
+
 #define MBOX_REG_SIZE			0x120
 #define MBOX_NR_REGS			(MBOX_REG_SIZE / sizeof(u32))
 
@@ -69,21 +77,33 @@ static inline void mbox_write_reg(u32 val, size_t ofs)
 /* Mailbox H/W preparations */
 static int omap2_mbox_startup(struct omap_mbox *mbox)
 {
-	unsigned int l;
+	u32 l;
+	unsigned long timeout;
 
 	mbox_ick_handle = clk_get(NULL, "mailboxes_ick");
 	if (IS_ERR(mbox_ick_handle)) {
-		printk("Could not get mailboxes_ick\n");
+		pr_err("Can't get mailboxes_ick\n");
 		return -ENODEV;
 	}
 	clk_enable(mbox_ick_handle);
 
+	mbox_write_reg(SOFTRESET, MAILBOX_SYSCONFIG);
+	timeout = jiffies + msecs_to_jiffies(20);
+	do {
+		l = mbox_read_reg(MAILBOX_SYSSTATUS);
+		if (l & RESETDONE)
+			break;
+	} while (!time_after(jiffies, timeout));
+
+	if (!(l & RESETDONE)) {
+		pr_err("Can't take mmu out of reset\n");
+		return -ENODEV;
+	}
+
 	l = mbox_read_reg(MAILBOX_REVISION);
 	pr_info("omap mailbox rev %d.%d\n", (l & 0xf0) >> 4, (l & 0x0f));
 
-	/* set smart-idle & autoidle */
-	l = mbox_read_reg(MAILBOX_SYSCONFIG);
-	l |= 0x00000011;
+	l = SMARTIDLE | AUTOIDLE;
 	mbox_write_reg(l, MAILBOX_SYSCONFIG);
 
 	omap2_mbox_enable_irq(mbox, IRQ_RX);
@@ -156,6 +176,9 @@ static void omap2_mbox_ack_irq(struct omap_mbox *mbox,
 	u32 bit = (irq == IRQ_TX) ? p->notfull_bit : p->newmsg_bit;
 
 	mbox_write_reg(bit, p->irqstatus);
+
+	/* Flush posted write for irq status to avoid spurious interrupts */
+	mbox_read_reg(p->irqstatus);
 }
 
 static int omap2_mbox_is_irq(struct omap_mbox *mbox,

arch/arm/mach-omap2/mux.c

@@ -460,6 +460,8 @@ MUX_CFG_34XX("AF26_34XX_GPIO0", 0x1e0,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
 MUX_CFG_34XX("AF22_34XX_GPIO9", 0xa18,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("AG9_34XX_GPIO23", 0x5ee,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
 MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
 MUX_CFG_34XX("U8_34XX_GPIO54_OUT", 0x0b4,
@@ -472,6 +474,8 @@ MUX_CFG_34XX("G25_34XX_GPIO86_OUT", 0x0fc,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("AG4_34XX_GPIO134_OUT", 0x160,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("AF4_34XX_GPIO135_OUT", 0x162,
+		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("AE4_34XX_GPIO136_OUT", 0x164,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("AF6_34XX_GPIO140_UP", 0x16c,

arch/arm/mach-omap2/pm-debug.c

@@ -541,7 +541,7 @@ static int __init pm_dbg_init(void)
 		printk(KERN_ERR "%s: only OMAP3 supported\n", __func__);
 		return -ENODEV;
 	}
-		
+
 	d = debugfs_create_dir("pm_debug", NULL);
 	if (IS_ERR(d))
 		return PTR_ERR(d);
@@ -551,7 +551,7 @@ static int __init pm_dbg_init(void)
 	(void) debugfs_create_file("time", S_IRUGO,
 		d, (void *)DEBUG_FILE_TIMERS, &debug_fops);
 
-	pwrdm_for_each(pwrdms_setup, (void *)d);
+	pwrdm_for_each_nolock(pwrdms_setup, (void *)d);
 
 	pm_dbg_dir = debugfs_create_dir("registers", d);
 	if (IS_ERR(pm_dbg_dir))

arch/arm/mach-omap2/pm34xx.c

@@ -51,97 +51,112 @@ static void (*_omap_sram_idle)(u32 *addr, int save_state);
 
 static struct powerdomain *mpu_pwrdm;
 
-/* PRCM Interrupt Handler for wakeups */
+/*
+ * PRCM Interrupt Handler Helper Function
+ *
+ * The purpose of this function is to clear any wake-up events latched
+ * in the PRCM PM_WKST_x registers. It is possible that a wake-up event
+ * may occur whilst attempting to clear a PM_WKST_x register and thus
+ * set another bit in this register. A while loop is used to ensure
+ * that any peripheral wake-up events occurring while attempting to
+ * clear the PM_WKST_x are detected and cleared.
+ */
+static int prcm_clear_mod_irqs(s16 module, u8 regs)
+{
+	u32 wkst, fclk, iclk, clken;
+	u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
+	u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1;
+	u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1;
+	u16 grpsel_off = (regs == 3) ?
+		OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL;
+	int c = 0;
+
+	wkst = prm_read_mod_reg(module, wkst_off);
+	wkst &= prm_read_mod_reg(module, grpsel_off);
+	if (wkst) {
+		iclk = cm_read_mod_reg(module, iclk_off);
+		fclk = cm_read_mod_reg(module, fclk_off);
+		while (wkst) {
+			clken = wkst;
+			cm_set_mod_reg_bits(clken, module, iclk_off);
+			/*
+			 * For USBHOST, we don't know whether HOST1 or
+			 * HOST2 woke us up, so enable both f-clocks
+			 */
+			if (module == OMAP3430ES2_USBHOST_MOD)
+				clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT;
+			cm_set_mod_reg_bits(clken, module, fclk_off);
+			prm_write_mod_reg(wkst, module, wkst_off);
+			wkst = prm_read_mod_reg(module, wkst_off);
+			c++;
+		}
+		cm_write_mod_reg(iclk, module, iclk_off);
+		cm_write_mod_reg(fclk, module, fclk_off);
+	}
+
+	return c;
+}
+
+static int _prcm_int_handle_wakeup(void)
+{
+	int c;
+
+	c = prcm_clear_mod_irqs(WKUP_MOD, 1);
+	c += prcm_clear_mod_irqs(CORE_MOD, 1);
+	c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1);
+	if (omap_rev() > OMAP3430_REV_ES1_0) {
+		c += prcm_clear_mod_irqs(CORE_MOD, 3);
+		c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1);
+	}
+
+	return c;
+}
+
+/*
+ * PRCM Interrupt Handler
+ *
+ * The PRM_IRQSTATUS_MPU register indicates if there are any pending
+ * interrupts from the PRCM for the MPU. These bits must be cleared in
+ * order to clear the PRCM interrupt. The PRCM interrupt handler is
+ * implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear
+ * the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU
+ * register indicates that a wake-up event is pending for the MPU and
+ * this bit can only be cleared if the all the wake-up events latched
+ * in the various PM_WKST_x registers have been cleared. The interrupt
+ * handler is implemented using a do-while loop so that if a wake-up
+ * event occurred during the processing of the prcm interrupt handler
+ * (setting a bit in the corresponding PM_WKST_x register and thus
+ * preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register)
+ * this would be handled.
+ */
 static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
 {
-	u32 wkst, irqstatus_mpu;
-	u32 fclk, iclk;
+	u32 irqstatus_mpu;
+	int c = 0;
 
-	/* WKUP */
-	wkst = prm_read_mod_reg(WKUP_MOD, PM_WKST);
-	if (wkst) {
-		iclk = cm_read_mod_reg(WKUP_MOD, CM_ICLKEN);
-		fclk = cm_read_mod_reg(WKUP_MOD, CM_FCLKEN);
-		cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_ICLKEN);
-		cm_set_mod_reg_bits(wkst, WKUP_MOD, CM_FCLKEN);
-		prm_write_mod_reg(wkst, WKUP_MOD, PM_WKST);
-		while (prm_read_mod_reg(WKUP_MOD, PM_WKST))
-			cpu_relax();
-		cm_write_mod_reg(iclk, WKUP_MOD, CM_ICLKEN);
-		cm_write_mod_reg(fclk, WKUP_MOD, CM_FCLKEN);
-	}
+	do {
+		irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
+					OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
-	/* CORE */
-	wkst = prm_read_mod_reg(CORE_MOD, PM_WKST1);
-	if (wkst) {
-		iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN1);
-		fclk = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
-		cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN1);
-		cm_set_mod_reg_bits(wkst, CORE_MOD, CM_FCLKEN1);
-		prm_write_mod_reg(wkst, CORE_MOD, PM_WKST1);
-		while (prm_read_mod_reg(CORE_MOD, PM_WKST1))
-			cpu_relax();
-		cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN1);
-		cm_write_mod_reg(fclk, CORE_MOD, CM_FCLKEN1);
-	}
-	wkst = prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3);
-	if (wkst) {
-		iclk = cm_read_mod_reg(CORE_MOD, CM_ICLKEN3);
-		fclk = cm_read_mod_reg(CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
-		cm_set_mod_reg_bits(wkst, CORE_MOD, CM_ICLKEN3);
-		cm_set_mod_reg_bits(wkst, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
-		prm_write_mod_reg(wkst, CORE_MOD, OMAP3430ES2_PM_WKST3);
-		while (prm_read_mod_reg(CORE_MOD, OMAP3430ES2_PM_WKST3))
-			cpu_relax();
-		cm_write_mod_reg(iclk, CORE_MOD, CM_ICLKEN3);
-		cm_write_mod_reg(fclk, CORE_MOD, OMAP3430ES2_CM_FCLKEN3);
-	}
+		if (irqstatus_mpu & (OMAP3430_WKUP_ST | OMAP3430_IO_ST)) {
+			c = _prcm_int_handle_wakeup();
 
-	/* PER */
-	wkst = prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST);
-	if (wkst) {
-		iclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_ICLKEN);
-		fclk = cm_read_mod_reg(OMAP3430_PER_MOD, CM_FCLKEN);
-		cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_ICLKEN);
-		cm_set_mod_reg_bits(wkst, OMAP3430_PER_MOD, CM_FCLKEN);
-		prm_write_mod_reg(wkst, OMAP3430_PER_MOD, PM_WKST);
-		while (prm_read_mod_reg(OMAP3430_PER_MOD, PM_WKST))
-			cpu_relax();
-		cm_write_mod_reg(iclk, OMAP3430_PER_MOD, CM_ICLKEN);
-		cm_write_mod_reg(fclk, OMAP3430_PER_MOD, CM_FCLKEN);
-	}
-
-	if (omap_rev() > OMAP3430_REV_ES1_0) {
-		/* USBHOST */
-		wkst = prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD, PM_WKST);
-		if (wkst) {
-			iclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
-					       CM_ICLKEN);
-			fclk = cm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
-					       CM_FCLKEN);
-			cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
-					    CM_ICLKEN);
-			cm_set_mod_reg_bits(wkst, OMAP3430ES2_USBHOST_MOD,
-					    CM_FCLKEN);
-			prm_write_mod_reg(wkst, OMAP3430ES2_USBHOST_MOD,
-					  PM_WKST);
-			while (prm_read_mod_reg(OMAP3430ES2_USBHOST_MOD,
-						PM_WKST))
-				cpu_relax();
-			cm_write_mod_reg(iclk, OMAP3430ES2_USBHOST_MOD,
-					 CM_ICLKEN);
-			cm_write_mod_reg(fclk, OMAP3430ES2_USBHOST_MOD,
-					 CM_FCLKEN);
+			/*
+			 * Is the MPU PRCM interrupt handler racing with the
+			 * IVA2 PRCM interrupt handler ?
+			 */
+			WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup "
+			     "but no wakeup sources are marked\n");
+		} else {
+			/* XXX we need to expand our PRCM interrupt handler */
+			WARN(1, "prcm: WARNING: PRCM interrupt received, but "
+			     "no code to handle it (%08x)\n", irqstatus_mpu);
 		}
-	}
 
-	irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
-					 OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-	prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
-			  OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+		prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
+					OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
-	while (prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET))
-		cpu_relax();
+	} while (prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET));
 
 	return IRQ_HANDLED;
 }
@@ -624,6 +639,16 @@ static void __init prcm_setup_regs(void)
 	prm_write_mod_reg(OMAP3430_IO_EN | OMAP3430_WKUP_EN,
 			  OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 
+	/* Enable GPIO wakeups in PER */
+	prm_write_mod_reg(OMAP3430_EN_GPIO2 | OMAP3430_EN_GPIO3 |
+			  OMAP3430_EN_GPIO4 | OMAP3430_EN_GPIO5 |
+			  OMAP3430_EN_GPIO6, OMAP3430_PER_MOD, PM_WKEN);
+	/* and allow them to wake up MPU */
+	prm_write_mod_reg(OMAP3430_GRPSEL_GPIO2 | OMAP3430_EN_GPIO3 |
+			  OMAP3430_GRPSEL_GPIO4 | OMAP3430_EN_GPIO5 |
+			  OMAP3430_GRPSEL_GPIO6,
+			  OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL);
+
 	/* Don't attach IVA interrupts */
 	prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
 	prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);

arch/arm/mach-omap2/powerdomain.c

@@ -273,35 +273,50 @@ struct powerdomain *pwrdm_lookup(const char *name)
 }
 
 /**
- * pwrdm_for_each - call function on each registered clockdomain
+ * pwrdm_for_each_nolock - call function on each registered clockdomain
  * @fn: callback function *
  *
  * Call the supplied function for each registered powerdomain.  The
  * callback function can return anything but 0 to bail out early from
- * the iterator.  The callback function is called with the pwrdm_rwlock
- * held for reading, so no powerdomain structure manipulation
- * functions should be called from the callback, although hardware
- * powerdomain control functions are fine.  Returns the last return
- * value of the callback function, which should be 0 for success or
- * anything else to indicate failure; or -EINVAL if the function
- * pointer is null.
+ * the iterator.  Returns the last return value of the callback function, which
+ * should be 0 for success or anything else to indicate failure; or -EINVAL if
+ * the function pointer is null.
  */
-int pwrdm_for_each(int (*fn)(struct powerdomain *pwrdm, void *user),
-			void *user)
+int pwrdm_for_each_nolock(int (*fn)(struct powerdomain *pwrdm, void *user),
+				void *user)
 {
 	struct powerdomain *temp_pwrdm;
-	unsigned long flags;
 	int ret = 0;
 
 	if (!fn)
 		return -EINVAL;
 
-	read_lock_irqsave(&pwrdm_rwlock, flags);
 	list_for_each_entry(temp_pwrdm, &pwrdm_list, node) {
 		ret = (*fn)(temp_pwrdm, user);
 		if (ret)
 			break;
 	}
+
+	return ret;
+}
+
+/**
+ * pwrdm_for_each - call function on each registered clockdomain
+ * @fn: callback function *
+ *
+ * This function is the same as 'pwrdm_for_each_nolock()', but keeps the
+ * &pwrdm_rwlock locked for reading, so no powerdomain structure manipulation
+ * functions should be called from the callback, although hardware powerdomain
+ * control functions are fine.
+ */
+int pwrdm_for_each(int (*fn)(struct powerdomain *pwrdm, void *user),
+			void *user)
+{
+	unsigned long flags;
+	int ret;
+
+	read_lock_irqsave(&pwrdm_rwlock, flags);
+	ret = pwrdm_for_each_nolock(fn, user);
 	read_unlock_irqrestore(&pwrdm_rwlock, flags);
 
 	return ret;

arch/arm/mach-omap2/serial.c

@@ -110,7 +110,7 @@ static struct plat_serial8250_port serial_platform_data2[] = {
 		.uartclk	= OMAP24XX_BASE_BAUD * 16,
 	}, {
 #ifdef CONFIG_ARCH_OMAP4
-		.membase	= IO_ADDRESS(OMAP_UART4_BASE),
+		.membase	= OMAP2_IO_ADDRESS(OMAP_UART4_BASE),
 		.mapbase	= OMAP_UART4_BASE,
 		.irq		= 70,
 		.flags		= UPF_BOOT_AUTOCONF,
@@ -126,7 +126,7 @@ static struct plat_serial8250_port serial_platform_data2[] = {
 #ifdef CONFIG_ARCH_OMAP4
 static struct plat_serial8250_port serial_platform_data3[] = {
 	{
-		.membase	= IO_ADDRESS(OMAP_UART4_BASE),
+		.membase	= OMAP2_IO_ADDRESS(OMAP_UART4_BASE),
 		.mapbase	= OMAP_UART4_BASE,
 		.irq		= 70,
 		.flags		= UPF_BOOT_AUTOCONF,
@@ -579,7 +579,7 @@ static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
 	{
 		.pdev = {
 			.name			= "serial8250",
-			.id			= 3
+			.id			= 3,
 			.dev			= {
 				.platform_data	= serial_platform_data3,
 			},

arch/arm/mach-sa1100/Kconfig

@@ -71,11 +71,6 @@ config SA1100_H3600
 	  <http://www.handhelds.org/Compaq/index.html#iPAQ_H3600>
 	  <http://www.compaq.com/products/handhelds/pocketpc/>
 
-config SA1100_H3XXX
-	bool
-	depends on SA1100_H3100 || SA1100_H3600
-	default y
-
 config SA1100_BADGE4
 	bool "HP Labs BadgePAD 4"
 	select SA1111

arch/arm/mach-sa1100/time.c

@@ -77,7 +77,7 @@ static struct clock_event_device ckevt_sa1100_osmr0 = {
 	.set_mode	= sa1100_osmr0_set_mode,
 };
 
-static cycle_t sa1100_read_oscr(void)
+static cycle_t sa1100_read_oscr(struct clocksource *s)
 {
 	return OSCR;
 }

arch/arm/mach-u300/gpio.c

@@ -281,6 +281,16 @@ int gpio_unregister_callback(unsigned gpio)
 }
 EXPORT_SYMBOL(gpio_unregister_callback);
 
+/* Non-zero means valid */
+int gpio_is_valid(int number)
+{
+	if (number >= 0 &&
+	    number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT))
+		return 1;
+	return 0;
+}
+EXPORT_SYMBOL(gpio_is_valid);
+
 int gpio_request(unsigned gpio, const char *label)
 {
 	if (gpio_pin[gpio].users)

arch/arm/mach-u300/include/mach/gpio.h

@@ -258,6 +258,7 @@
 #define PIN_TO_PORT(val) (val >> 3)
 
 /* These can be found in arch/arm/mach-u300/gpio.c */
+extern int gpio_is_valid(int number);
 extern int gpio_request(unsigned gpio, const char *label);
 extern void gpio_free(unsigned gpio);
 extern int gpio_direction_input(unsigned gpio);

arch/arm/mm/Kconfig

@@ -17,7 +17,7 @@ config CPU_ARM610
 	select CPU_CP15_MMU
 	select CPU_COPY_V3 if MMU
 	select CPU_TLB_V3 if MMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	help
 	  The ARM610 is the successor to the ARM3 processor
 	  and was produced by VLSI Technology Inc.
@@ -31,7 +31,7 @@ config CPU_ARM7TDMI
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	help
 	  A 32-bit RISC microprocessor based on the ARM7 processor core
@@ -49,7 +49,7 @@ config CPU_ARM710
 	select CPU_CP15_MMU
 	select CPU_COPY_V3 if MMU
 	select CPU_TLB_V3 if MMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	help
 	  A 32-bit RISC microprocessor based on the ARM7 processor core
 	  designed by Advanced RISC Machines Ltd. The ARM710 is the
@@ -64,7 +64,7 @@ config CPU_ARM720T
 	bool "Support ARM720T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -83,7 +83,7 @@ config CPU_ARM740T
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V3	# although the core is v4t
 	select CPU_CP15_MPU
 	help
@@ -100,7 +100,7 @@ config CPU_ARM9TDMI
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	help
 	  A 32-bit RISC microprocessor based on the ARM9 processor core
@@ -114,7 +114,7 @@ config CPU_ARM920T
 	bool "Support ARM920T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -135,7 +135,7 @@ config CPU_ARM922T
 	bool "Support ARM922T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -154,7 +154,7 @@ config CPU_ARM925T
  	bool "Support ARM925T processor" if ARCH_OMAP1
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -173,7 +173,7 @@ config CPU_ARM926T
 	bool "Support ARM926T processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB
 	select CPU_32v5
 	select CPU_ABRT_EV5TJ
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU
@@ -191,7 +191,7 @@ config CPU_FA526
 	bool
 	select CPU_32v4
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_CACHE_FA
@@ -210,7 +210,7 @@ config CPU_ARM940T
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MPU
 	help
@@ -228,7 +228,7 @@ config CPU_ARM946E
 	depends on !MMU
 	select CPU_32v5
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MPU
 	help
@@ -244,7 +244,7 @@ config CPU_ARM1020
 	bool "Support ARM1020T (rev 0) processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -262,7 +262,7 @@ config CPU_ARM1020E
 	bool "Support ARM1020E processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -275,7 +275,7 @@ config CPU_ARM1022
 	bool "Support ARM1022E processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU # can probably do better
@@ -293,7 +293,7 @@ config CPU_ARM1026
 	bool "Support ARM1026EJ-S processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV5T # But need Jazelle, but EV5TJ ignores bit 10
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU # can probably do better
@@ -311,7 +311,7 @@ config CPU_SA110
 	select CPU_32v3 if ARCH_RPC
 	select CPU_32v4 if !ARCH_RPC
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WB
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -331,7 +331,7 @@ config CPU_SA1100
 	bool
 	select CPU_32v4
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WB
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -342,7 +342,7 @@ config CPU_XSCALE
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -352,7 +352,7 @@ config CPU_XSC3
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -363,7 +363,7 @@ config CPU_MOHAWK
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -374,7 +374,7 @@ config CPU_FEROCEON
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_FEROCEON if MMU
@@ -394,7 +394,7 @@ config CPU_V6
 	bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX
 	select CPU_32v6
 	select CPU_ABRT_EV6
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_V6
 	select CPU_CACHE_V6
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
@@ -420,7 +420,7 @@ config CPU_V7
 	select CPU_32v6K
 	select CPU_32v7
 	select CPU_ABRT_EV7
-	select CPU_PABRT_IFAR
+	select CPU_PABRT_V7
 	select CPU_CACHE_V7
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
@@ -482,10 +482,13 @@ config CPU_ABRT_EV6
 config CPU_ABRT_EV7
 	bool
 
-config CPU_PABRT_IFAR
+config CPU_PABRT_LEGACY
 	bool
 
-config CPU_PABRT_NOIFAR
+config CPU_PABRT_V6
+	bool
+
+config CPU_PABRT_V7
 	bool
 
 # The cache model

arch/arm/mm/Makefile

@@ -27,6 +27,10 @@ obj-$(CONFIG_CPU_ABRT_EV5TJ)	+= abort-ev5tj.o
 obj-$(CONFIG_CPU_ABRT_EV6)	+= abort-ev6.o
 obj-$(CONFIG_CPU_ABRT_EV7)	+= abort-ev7.o
 
+obj-$(CONFIG_CPU_PABRT_LEGACY)	+= pabort-legacy.o
+obj-$(CONFIG_CPU_PABRT_V6)	+= pabort-v6.o
+obj-$(CONFIG_CPU_PABRT_V7)	+= pabort-v7.o
+
 obj-$(CONFIG_CPU_CACHE_V3)	+= cache-v3.o
 obj-$(CONFIG_CPU_CACHE_V4)	+= cache-v4.o
 obj-$(CONFIG_CPU_CACHE_V4WT)	+= cache-v4wt.o

arch/arm/mm/fault.c

@@ -519,9 +519,58 @@ do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	arm_notify_die("", regs, &info, fsr, 0);
 }
 
+
+static struct fsr_info ifsr_info[] = {
+	{ do_bad,		SIGBUS,  0,		"unknown 0"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 1"			   },
+	{ do_bad,		SIGBUS,  0,		"debug event"			   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"section access flag fault"	   },
+	{ do_bad,		SIGBUS,  0,		"unknown 4"			   },
+	{ do_translation_fault,	SIGSEGV, SEGV_MAPERR,	"section translation fault"	   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"page access flag fault"	   },
+	{ do_page_fault,	SIGSEGV, SEGV_MAPERR,	"page translation fault"	   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on non-linefetch"  },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"section domain fault"		   },
+	{ do_bad,		SIGBUS,  0,		"unknown 10"			   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"page domain fault"		   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on translation"	   },
+	{ do_sect_fault,	SIGSEGV, SEGV_ACCERR,	"section permission fault"	   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on translation"	   },
+	{ do_page_fault,	SIGSEGV, SEGV_ACCERR,	"page permission fault"		   },
+	{ do_bad,		SIGBUS,  0,		"unknown 16"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 17"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 18"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 19"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 20"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 21"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 22"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 23"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 24"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 25"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 26"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 27"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 28"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 29"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 30"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 31"			   },
+};
+
 asmlinkage void __exception
-do_PrefetchAbort(unsigned long addr, struct pt_regs *regs)
+do_PrefetchAbort(unsigned long addr, unsigned int ifsr, struct pt_regs *regs)
 {
-	do_translation_fault(addr, FSR_LNX_PF, regs);
+	const struct fsr_info *inf = ifsr_info + fsr_fs(ifsr);
+	struct siginfo info;
+
+	if (!inf->fn(addr, ifsr | FSR_LNX_PF, regs))
+		return;
+
+	printk(KERN_ALERT "Unhandled prefetch abort: %s (0x%03x) at 0x%08lx\n",
+		inf->name, ifsr, addr);
+
+	info.si_signo = inf->sig;
+	info.si_errno = 0;
+	info.si_code  = inf->code;
+	info.si_addr  = (void __user *)addr;
+	arm_notify_die("", regs, &info, ifsr, 0);
 }
 

arch/arm/mm/mmap.c

@@ -124,7 +124,7 @@ int valid_phys_addr_range(unsigned long addr, size_t size)
 {
 	if (addr < PHYS_OFFSET)
 		return 0;
-	if (addr + size >= __pa(high_memory - 1))
+	if (addr + size > __pa(high_memory - 1) + 1)
 		return 0;
 
 	return 1;

arch/arm/mm/mmu.c

@@ -21,6 +21,7 @@
 #include <asm/cachetype.h>
 #include <asm/setup.h>
 #include <asm/sizes.h>
+#include <asm/smp_plat.h>
 #include <asm/tlb.h>
 #include <asm/highmem.h>
 
@@ -709,10 +710,6 @@ static void __init sanity_check_meminfo(void)
 			if (meminfo.nr_banks >= NR_BANKS) {
 				printk(KERN_CRIT "NR_BANKS too low, "
 						 "ignoring high memory\n");
-			} else if (cache_is_vipt_aliasing()) {
-				printk(KERN_CRIT "HIGHMEM is not yet supported "
-						 "with VIPT aliasing cache, "
-						 "ignoring high memory\n");
 			} else {
 				memmove(bank + 1, bank,
 					(meminfo.nr_banks - i) * sizeof(*bank));
@@ -726,6 +723,8 @@ static void __init sanity_check_meminfo(void)
 			bank->size = VMALLOC_MIN - __va(bank->start);
 		}
 #else
+		bank->highmem = highmem;
+
 		/*
 		 * Check whether this memory bank would entirely overlap
 		 * the vmalloc area.
@@ -754,6 +753,38 @@ static void __init sanity_check_meminfo(void)
 #endif
 		j++;
 	}
+#ifdef CONFIG_HIGHMEM
+	if (highmem) {
+		const char *reason = NULL;
+
+		if (cache_is_vipt_aliasing()) {
+			/*
+			 * Interactions between kmap and other mappings
+			 * make highmem support with aliasing VIPT caches
+			 * rather difficult.
+			 */
+			reason = "with VIPT aliasing cache";
+#ifdef CONFIG_SMP
+		} else if (tlb_ops_need_broadcast()) {
+			/*
+			 * kmap_high needs to occasionally flush TLB entries,
+			 * however, if the TLB entries need to be broadcast
+			 * we may deadlock:
+			 *  kmap_high(irqs off)->flush_all_zero_pkmaps->
+			 *  flush_tlb_kernel_range->smp_call_function_many
+			 *   (must not be called with irqs off)
+			 */
+			reason = "without hardware TLB ops broadcasting";
+#endif
+		}
+		if (reason) {
+			printk(KERN_CRIT "HIGHMEM is not supported %s, ignoring high memory\n",
+				reason);
+			while (j > 0 && meminfo.bank[j - 1].highmem)
+				j--;
+		}
+	}
+#endif
 	meminfo.nr_banks = j;
 }
 

arch/arm/mm/pabort-legacy.S

@@ -0,0 +1,19 @@
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: legacy_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = Simulated IFSR with section translation fault status
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(legacy_pabort)
+	mov	r1, #5
+	mov	pc, lr
+ENDPROC(legacy_pabort)

arch/arm/mm/pabort-v6.S

@@ -0,0 +1,19 @@
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(v6_pabort)
+	mrc	p15, 0, r1, c5, c0, 1		@ get IFSR
+	mov	pc, lr
+ENDPROC(v6_pabort)

arch/arm/mm/pabort-v7.S

@@ -0,0 +1,20 @@
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(v7_pabort)
+	mrc	p15, 0, r0, c6, c0, 2		@ get IFAR
+	mrc	p15, 0, r1, c5, c0, 1		@ get IFSR
+	mov	pc, lr
+ENDPROC(v7_pabort)

arch/arm/mm/proc-arm1020.S

@@ -449,7 +449,7 @@ arm1020_crval:
 	.type	arm1020_processor_functions, #object
 arm1020_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1020_proc_init
 	.word	cpu_arm1020_proc_fin
 	.word	cpu_arm1020_reset

arch/arm/mm/proc-arm1020e.S

@@ -430,7 +430,7 @@ arm1020e_crval:
 	.type	arm1020e_processor_functions, #object
 arm1020e_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1020e_proc_init
 	.word	cpu_arm1020e_proc_fin
 	.word	cpu_arm1020e_reset

arch/arm/mm/proc-arm1022.S

@@ -413,7 +413,7 @@ arm1022_crval:
 	.type	arm1022_processor_functions, #object
 arm1022_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1022_proc_init
 	.word	cpu_arm1022_proc_fin
 	.word	cpu_arm1022_reset

arch/arm/mm/proc-arm1026.S

@@ -408,7 +408,7 @@ arm1026_crval:
 	.type	arm1026_processor_functions, #object
 arm1026_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1026_proc_init
 	.word	cpu_arm1026_proc_fin
 	.word	cpu_arm1026_reset

arch/arm/mm/proc-arm6_7.S

@@ -278,7 +278,7 @@ __arm7_setup:	mov	r0, #0
 		.type	arm6_processor_functions, #object
 ENTRY(arm6_processor_functions)
 		.word	cpu_arm6_data_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm6_proc_init
 		.word	cpu_arm6_proc_fin
 		.word	cpu_arm6_reset
@@ -295,7 +295,7 @@ ENTRY(arm6_processor_functions)
 		.type	arm7_processor_functions, #object
 ENTRY(arm7_processor_functions)
 		.word	cpu_arm7_data_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm7_proc_init
 		.word	cpu_arm7_proc_fin
 		.word	cpu_arm7_reset

arch/arm/mm/proc-arm720.S

@@ -181,7 +181,7 @@ arm720_crval:
 		.type	arm720_processor_functions, #object
 ENTRY(arm720_processor_functions)
 		.word	v4t_late_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm720_proc_init
 		.word	cpu_arm720_proc_fin
 		.word	cpu_arm720_reset

arch/arm/mm/proc-arm740.S

@@ -126,7 +126,7 @@ __arm740_setup:
 	.type	arm740_processor_functions, #object
 ENTRY(arm740_processor_functions)
 	.word	v4t_late_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm740_proc_init
 	.word	cpu_arm740_proc_fin
 	.word	cpu_arm740_reset

arch/arm/mm/proc-arm7tdmi.S

@@ -64,7 +64,7 @@ __arm7tdmi_setup:
 		.type	arm7tdmi_processor_functions, #object
 ENTRY(arm7tdmi_processor_functions)
 		.word	v4t_late_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm7tdmi_proc_init
 		.word	cpu_arm7tdmi_proc_fin
 		.word	cpu_arm7tdmi_reset

arch/arm/mm/proc-arm920.S

@@ -395,7 +395,7 @@ arm920_crval:
 	.type	arm920_processor_functions, #object
 arm920_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm920_proc_init
 	.word	cpu_arm920_proc_fin
 	.word	cpu_arm920_reset

arch/arm/mm/proc-arm922.S

@@ -399,7 +399,7 @@ arm922_crval:
 	.type	arm922_processor_functions, #object
 arm922_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm922_proc_init
 	.word	cpu_arm922_proc_fin
 	.word	cpu_arm922_reset

arch/arm/mm/proc-arm925.S

@@ -462,7 +462,7 @@ arm925_crval:
 	.type	arm925_processor_functions, #object
 arm925_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm925_proc_init
 	.word	cpu_arm925_proc_fin
 	.word	cpu_arm925_reset

arch/arm/mm/proc-arm926.S

@@ -415,7 +415,7 @@ arm926_crval:
 	.type	arm926_processor_functions, #object
 arm926_processor_functions:
 	.word	v5tj_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm926_proc_init
 	.word	cpu_arm926_proc_fin
 	.word	cpu_arm926_reset

arch/arm/mm/proc-arm940.S

@@ -322,7 +322,7 @@ __arm940_setup:
 	.type	arm940_processor_functions, #object
 ENTRY(arm940_processor_functions)
 	.word	nommu_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm940_proc_init
 	.word	cpu_arm940_proc_fin
 	.word	cpu_arm940_reset

arch/arm/mm/proc-arm946.S

@@ -377,7 +377,7 @@ __arm946_setup:
 	.type	arm946_processor_functions, #object
 ENTRY(arm946_processor_functions)
 	.word	nommu_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm946_proc_init
 	.word	cpu_arm946_proc_fin
 	.word	cpu_arm946_reset

arch/arm/mm/proc-arm9tdmi.S

@@ -64,7 +64,7 @@ __arm9tdmi_setup:
 		.type	arm9tdmi_processor_functions, #object
 ENTRY(arm9tdmi_processor_functions)
 		.word	nommu_early_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm9tdmi_proc_init
 		.word	cpu_arm9tdmi_proc_fin
 		.word	cpu_arm9tdmi_reset

arch/arm/mm/proc-fa526.S

@@ -191,7 +191,7 @@ fa526_cr1_set:
 	.type	fa526_processor_functions, #object
 fa526_processor_functions:
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_fa526_proc_init
 	.word	cpu_fa526_proc_fin
 	.word	cpu_fa526_reset

arch/arm/mm/proc-feroceon.S

@@ -499,7 +499,7 @@ feroceon_crval:
 	.type	feroceon_processor_functions, #object
 feroceon_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_feroceon_proc_init
 	.word	cpu_feroceon_proc_fin
 	.word	cpu_feroceon_reset

arch/arm/mm/proc-mohawk.S

@@ -359,7 +359,7 @@ mohawk_crval:
 	.type	mohawk_processor_functions, #object
 mohawk_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_mohawk_proc_init
 	.word	cpu_mohawk_proc_fin
 	.word	cpu_mohawk_reset

arch/arm/mm/proc-sa110.S

@@ -199,7 +199,7 @@ sa110_crval:
 	.type	sa110_processor_functions, #object
 ENTRY(sa110_processor_functions)
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_sa110_proc_init
 	.word	cpu_sa110_proc_fin
 	.word	cpu_sa110_reset

arch/arm/mm/proc-sa1100.S

@@ -214,7 +214,7 @@ sa1100_crval:
 	.type	sa1100_processor_functions, #object
 ENTRY(sa1100_processor_functions)
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_sa1100_proc_init
 	.word	cpu_sa1100_proc_fin
 	.word	cpu_sa1100_reset

arch/arm/mm/proc-v6.S

@@ -191,7 +191,7 @@ v6_crval:
 	.type	v6_processor_functions, #object
 ENTRY(v6_processor_functions)
 	.word	v6_early_abort
-	.word	pabort_noifar
+	.word	v6_pabort
 	.word	cpu_v6_proc_init
 	.word	cpu_v6_proc_fin
 	.word	cpu_v6_reset