make randconfig bootup testing found that the cpufreq code
crashes on bootup, if the powernow-k8 driver is enabled and
if maxcpus=1 passed on the boot line to a !CONFIG_HOTPLUG_CPU
kernel.
First lockdep found out that there's an inconsistent unlock
sequence:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
swapper/1 is trying to release lock (&per_cpu(cpu_policy_rwsem, cpu)) at:
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
but there are no more locks to release!
Call Trace:
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
[<ffffffff80251c29>] print_unlock_inbalance_bug+0x104/0x12c
[<ffffffff80252f3a>] mark_held_locks+0x56/0x94
[<ffffffff806ffd8e>] unlock_policy_rwsem_write+0x3c/0x42
[<ffffffff807008b6>] cpufreq_add_dev+0x2a8/0x5c4
...
then shortly afterwards the cpufreq code crashed on an assert:
------------[ cut here ]------------
kernel BUG at drivers/cpufreq/cpufreq.c:1068!
invalid opcode: 0000 [1] SMP
[...]
Call Trace:
[<ffffffff805145d6>] sysdev_driver_unregister+0x5b/0x91
[<ffffffff806ff520>] cpufreq_register_driver+0x15d/0x1a2
[<ffffffff80cc0596>] powernowk8_init+0x86/0x94
[...]
---[ end trace 1e9219be2b4431de ]---
the bug was caused by maxcpus=1 bootup, which brought up the
secondary core as !cpu_online() but !cpu_is_offline() either,
which on on !CONFIG_HOTPLUG_CPU is always 0 (include/linux/cpu.h):
/* CPUs don't go offline once they're online w/o CONFIG_HOTPLUG_CPU */
static inline int cpu_is_offline(int cpu) { return 0; }
but the cpufreq code uses cpu_online() and cpu_is_offline() in
a mixed way - the low-level drivers use cpu_online(), while
the cpufreq core uses cpu_is_offline(). This opened up the
possibility to add the non-initialized sysdev device of the
secondary core:
cpufreq-core: trying to register driver powernow-k8
cpufreq-core: adding CPU 0
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
cpufreq-core: initialization failed
cpufreq-core: adding CPU 1
cpufreq-core: initialization failed
which then blew up. The fix is to make cpu_is_offline() always
the negation of cpu_online(). With that fix applied the kernel
boots up fine without crashing:
Calling initcall 0xffffffff80cc0510: powernowk8_init+0x0/0x94()
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (1 cpu cores) (version 2.20.00)
powernow-k8: BIOS error - no PSB or ACPI _PSS objects
initcall 0xffffffff80cc0510: powernowk8_init+0x0/0x94() returned -19.
initcall 0xffffffff80cc0510 ran for 19 msecs: powernowk8_init+0x0/0x94()
Calling initcall 0xffffffff80cc328f: init_lapic_nmi_sysfs+0x0/0x39()
We could fix this by making CPU enumeration aware of max_cpus, but that
would be more fragile IMO, and the cpu_online(cpu) != cpu_is_offline(cpu)
possibility was quite confusing and a continuous source of bugs too.
Most distributions have kernels with CPU hotplug enabled, so this bug
remained hidden for a long time.
Bug forensics:
The broken cpu_is_offline() API variant was introduced via:
commit a59d2e4e6977e7b94e003c96a41f07e96cddc340
Author: Rusty Russell <rusty@rustcorp.com.au>
Date: Mon Mar 8 06:06:03 2004 -0800
[PATCH] minor cleanups for hotplug CPUs
( this predates linux-2.6.git, this commit is available from Thomas's
historic git tree. )
Then 1.5 years later the cpufreq code made use of it:
commit c32b6b8e52
Author: Ashok Raj <ashok.raj@intel.com>
Date: Sun Oct 30 14:59:54 2005 -0800
[PATCH] create and destroy cpufreq sysfs entries based on cpu notifiers
+ if (cpu_is_offline(cpu))
+ return 0;
which is a correct use of the subtly broken new API. v2.6.15 then
shipped with this bug included.
then it took two more years for random-kernel qa to hit it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit ac40532ef0, which gets
us back the original cleanup of 6f5391c283.
It turns out that the bug that was triggered by that commit was
apparently not actually triggered by that commit at all, and just the
testing conditions had changed enough to make it appear to be due to it.
The real problem seems to have been found by Peter Osterlund:
"pktcdvd sets it [block device size] when opening the /dev/pktcdvd
device, but when the drive is later opened as /dev/scd0, there is
nothing that sets it back. (Btw, 40944 is possible if the disk is a
CDRW that was formatted with "cdrwtool -m 10236".)
The problem is that pktcdvd opens the cd device in non-blocking mode
when pktsetup is run, and doesn't close it again until pktsetup -d is
run. The effect is that if you meanwhile open the cd device,
blkdev.c:do_open() doesn't call bd_set_size() because
bdev->bd_openers is non-zero."
In particular, to repeat the bug (regardless of whether commit
6f5391c283 is applied or not):
" 1. Start with an empty drive.
2. pktsetup 0 /dev/scd0
3. Insert a CD containing an isofs filesystem.
4. mount /dev/pktcdvd/0 /mnt/tmp
5. umount /mnt/tmp
6. Press the eject button.
7. Insert a DVD containing a non-writable filesystem.
8. mount /dev/scd0 /mnt/tmp
9. find /mnt/tmp -type f -print0 | xargs -0 sha1sum >/dev/null
10. If the DVD contains data beyond the physical size of a CD, you
get I/O errors in the terminal, and dmesg reports lots of
"attempt to access beyond end of device" errors."
which in turn is because the nested open after the media change won't
cause the size to be set properly (because the original open still holds
the block device, and we only do the bd_set_size() when we don't have
other people holding the device open).
The proper fix for that is probably to just do something like
bdev->bd_inode->i_size = (loff_t)get_capacity(disk)<<9;
in fs/block_dev.c:do_open() even for the cases where we're not the
original opener (but *not* call bd_set_size(), since that will also
change the block size of the device).
Cc: Peter Osterlund <petero2@telia.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SCSI SRP transport class currently iterates over all children
devices of the host that is being removed in srp_remove_host(). However,
not all of those children were created by the SRP transport, and
removing them will cause corruption and an oops when their creator tries
to remove them.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[ISDN]: i4l: Fix DLE handling for i4l-audio
[ISDN] i4l: 'NO CARRIER' message lost after ldisc flush
[CONNECTOR]: Return proper error code in cn_call_callback()
[INET]: Fix netdev renaming and inet address labels
[CASSINI]: Bump driver version and release date.
[CASSINI]: Fix two obvious NAPI bugs.
[CASSINI]: Set skb->truesize properly on receive packets.
[CASSINI]: Program parent Intel31154 bridge when necessary.
[CASSINI]: Revert 'dont touch page_count'.
[CASSINI]: Fix endianness bug.
[XFRM]: Do not define km_migrate() if !CONFIG_XFRM_MIGRATE
[X25]: Add missing x25_neigh_put
The DLE handling in i4l-audio seems to be broken.
It produces spurious DLEs so asterisk 1.2.24 with chan_modem_i4l
gets irritated, the error message is:
"chan_modem_i4l.c:450 i4l_read: Value of escape is ^ (17)".
-> There shouldn't be a DLE-^.
If a spurious DLE-ETX occurs, the audio connection even dies.
I use a "AVM Fritz!PCI" isdn card.
I found two issues that only appear if ISDN_AUDIO_SKB_DLECOUNT(skb) > 0:
- The loop in isdn_tty.c:isdn_tty_try_read() doesn't escape a DLE if it's
the last character.
- The loop in isdn_common.c:isdn_readbchan_tty() doesn't copy its characters,
it only remembers the last one ("last = *p;").
Compare it with the loop in isdn_common.c:isdn_readbchan(), that *does*
copy them ("*cp++ = *p;") correctly.
The special handling of the "last" character made it more difficult.
I compared it to linux-2.4.19: There was no "last"-handling and both loops
did escape and copy all characters correctly.
Signed-off-by: Matthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ISDN tty layer doesn't produce a 'NO CARRIER' message after hangup.
I suppose it broke when tty_buffer_flush() has been added to
tty_ldisc_flush() in the commit below.
For isdn_tty_modem_result(RESULT_NO_CARRIER..) the
message inserted via isdn_tty_at_cout() -> tty_insert_flip_char()
is flushed immediately by tty_ldisc_flush() -> tty_buffer_flush().
More annoyingly, the audio abort sequence DLE-ETX is also lost.
This patch fixes only active audio connections, because I assume that nobody
changes the line discipline for audio.
For non-audio connections the problem remains.
Maybe we can remove the tty_ldisc_flush() in isdn_tty_modem_result()
at all because it's done at tty_close?
On Mon, May 07, 2007 at 04:05:57PM -0500, Paul Fulghum wrote:
> Flush the tty flip buffer when the line discipline
> input queue is flushed, including the user call
> tcflush(TCIFLUSH/TCIOFLUSH). This prevents unexpected
> stale data after a user application calls tcflush().
>
> Cc: Alan Cox <alan@lxorguk.org.uk>
> Cc: Antonino Ingargiola <tritemio@gmail.com>
> Signed-off-by: Paul Fulghum <paulkf@microgate.com>
>
> --- a/drivers/char/tty_io.c 2007-05-04 05:46:55.000000000 -0500
> +++ b/drivers/char/tty_io.c 2007-05-05 03:23:46.000000000 -0500
> @@ -1240,6 +1263,7 @@ void tty_ldisc_flush(struct tty_struct *
> ld->flush_buffer(tty);
> tty_ldisc_deref(ld);
> }
> + tty_buffer_flush(tty);
[..]
Signed-off-by: Matthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code should be set to EINVAL instead of ENODEV if !queue_work().
There's another call of queue_work() which may set err to EINVAL.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-naming an interface, the previous secondary address
labels get lost e.g.
$> brctl addbr foo
$> ip addr add 192.168.0.1 dev foo
$> ip addr add 192.168.0.2 dev foo label foo:00
$> ip addr show dev foo | grep inet
inet 192.168.0.1/32 scope global foo
inet 192.168.0.2/32 scope global foo:00
$> ip link set foo name bar
$> ip addr show dev bar | grep inet
inet 192.168.0.1/32 scope global bar
inet 192.168.0.2/32 scope global bar:2
Turns out to be a simple thinko in inetdev_changename() - clearly we
want to look at the address label, rather than the device name, for
a suffix to retain.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts changeset fa4f0774d7
([CASSINI]: dont touch page_count) because it breaks the driver.
The local page counting added by this changeset did not account
for the asynchronous page count changes done by kfree_skb()
and friends.
The change adds extra atomics and on top of it all appears to be
totally unnecessary as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Nick Piggin <npiggin@suse.de>
Here's proposed fix for RX checksum handling in cassini; it affects
little-endian working with half-duplex gigabit, but obviously needs
testing on big-endian too.
The problem is, we need to convert checksum to fixed-endian *before*
correcting for (unstripped) FCS. On big-endian it won't matter
(conversion is no-op), on little-endian it will, but only if FCS is
not stripped by hardware; i.e. in half-duplex gigabit mode when
->crc_size is set.
cassini.c part is that fix, cassini.h one consists of trivial
endianness annotations. With that applied the sucker is endian-clean,
according to sparse.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In include/net/xfrm.h we find :
#ifdef CONFIG_XFRM_MIGRATE
extern int km_migrate(struct xfrm_selector *sel, u8 dir, u8 type,
struct xfrm_migrate *m, int num_bundles);
...
#endif
We can also guard the function body itself in net/xfrm/xfrm_state.c
with same condition.
(Problem spoted by sparse checker)
make C=2 net/xfrm/xfrm_state.o
...
net/xfrm/xfrm_state.c:1765:5: warning: symbol 'km_migrate' was not declared. Should it be static?
...
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function x25_get_neigh increments a reference count. At the point of
the second goto out, the result of calling x25_get_neigh is only stored in
a local variable, and thus no one outside the function will be able to
decrease the reference count. Thus, x25_neigh_put should be called before
the return in this case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* if ((E = x25_get_neigh(...)) == NULL)
S
... when != x25_neigh_put(...,(T1)E,...)
when != if (E != NULL) { ... x25_neigh_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != x25_neigh_put(...,(T2)E,...)
when != if (E != NULL) { ... x25_neigh_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Montecito and Montvale behaves slightly differently than previous
Itanium processors, resulting in the MCA due to a failed PIO read
to sometimes surfacing outside the nofault code. This code is
based on discussions with Intel CPU architects and verified at
customer sites.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I neglected to send Tony the most recent version of the
patch ("Fix Altix BTE error return status") applied
as commit: 64135fa97c
This patch gets it up to date. Without this patch
on shub2, if there is no error xpcBteUnmappedError is
returned instead of xpcSuccess.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The console is now by default in UTF-8 mode. Fix the documentation on
the default value, so that we can explain behaviour that otherwise
causes bug-reports like this:
http://bugzilla.kernel.org/show_bug.cgi?id=9319
Also add the needed "vt." prefix, so that the boot-time config options
to switch back to the legacy 8-bit mode is actually documented
correctly.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFSv4: Fix open_to_lock_owner sequenceid allocation...
NFSv4: nfs4_open_confirm must not set the open_owner as confirmed on error
NFS: add newline to kernel warning message in auth_gss code
NFSv4: Fix circular locking dependency in nfs4_kill_renewd
NFS: Fix a possible Oops in fs/nfs/super.c
Add a missing call to srp_remove_host() in srp_remove_one() so that we
don't leak SRP transport class list entries.
Tested-by: David Dillow <dillowda@ornl.gov>
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
NFSv4 file locking is currently completely broken since it doesn't respect
the OPEN sequencing when it is given an unconfirmed lock_owner and needs to
do an open_to_lock_owner. Worse: it breaks the sunrpc rules by doing a
GFP_KERNEL allocation inside an rpciod callback.
Fix is to preallocate the open seqid structure in nfs4_alloc_lockdata if we
see that the lock_owner is unconfirmed.
Then, in nfs4_lock_prepare() we wait for either the open_seqid, if
the lock_owner is still unconfirmed, or else fall back to waiting on the
standard lock_seqid.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RFC3530 states that the open_owner is confirmed if and only if the client
sends an OPEN_CONFIRM request with the appropriate sequence id and stateid
within the lease period.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Sigh... commit 4584f520e1 (NFS: Fix NFS
mountpoint crossing...) had a slight flaw: server can be NULL if sget()
returned an existing superblock.
Fix the fix by dereferencing s->s_fs_info.
Thanks to Coverity/Adrian Bunk and Frank Filz for spotting the bug.
(See http://bugzilla.kernel.org/show_bug.cgi?id=9647)
Also add in the same namespace Oops fix for NFSv4 in both the mountpoint
crossing case, and the referral case.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The VID input level change has been reported to cause trouble. Be more
careful in this respect:
* Only change the level on the W83627EHF/EHG. The W83627DHG is more
complex in this respect.
* Don't change the level if the VID pins are in output mode.
* Only set the level to TTL if VRM 9.x is used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The previous commit missed one use of "may_attach()" that had been
renamed to __ptrace_may_attach(). Tssk, tssk, Al.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Contents of /proc/*/maps is sensitive and may become sensitive after
open() (e.g. if target originally shares our ->mm and later does exec
on suid-root binary).
Check at read() (actually, ->start() of iterator) time that mm_struct
we'd grabbed and locked is
- still the ->mm of target
- equal to reader's ->mm or the target is ptracable by reader.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both SLUB and SLAB really did almost exactly the same thing for
/proc/slabinfo setup, using duplicate code and per-allocator #ifdef's.
This just creates a common CONFIG_SLABINFO that is enabled by both SLUB
and SLAB, and shares all the setup code. Maybe SLOB will want this some
day too.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A recent bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=9674
Was caused because the ULDs now set their own prep functions, but
don't necessarily reset the prep function back to the SCSI default
when they are removed. This leads to panics if commands are sent to
the device after the module is removed because the prep_fn is still
pointing to the old module code. The fix for this is to implement a
bus remove method that resets the prep_fn pointer correctly before
calling the ULD specific driver remove method.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to register slabinfo to procfs when CONFIG_SLUB is enabled to
make the file actually visible to user-space.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
After 17d57a9206 ("x86: fix x86-32 early
fixmap initialization.") removing lg.ko caused a printk from vunmap:
mm/memory.c:115: bad pgd 004b3027.
On the second use after module load, the kernel crashes.
This fixes the immediate problem (accessed and dirty bits not set as
expected in pmd_none_or_clear_bad). I can't see why this would cause
a crash, but I haven't been able to reproduce it once this is applied.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use __asm__ and __volatile__ in code that is exported to userspace. Wrap
kernel functions with __KERNEL__ so they get scrubbed.
No code changed:
text data bss dec hex filename
9681036 1698924 3407872 14787832 e1a4f8 vmlinux.before
9681036 1698924 3407872 14787832 e1a4f8 vmlinux.after
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since asm-x86/byteorder.h is exported to userspace, use __asm__ rather than
asm in its code.
Signed-Off-By: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Covert leds_list_lock to a rw_sempahore to match previous LED trigger
locking fixes, fixing lock ordering.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Meelis Roos reported these warnings on sparc64:
CC kernel/sched.o
In file included from kernel/sched.c:879:
kernel/sched_debug.c: In function 'nsec_high':
kernel/sched_debug.c:38: warning: comparison of distinct pointer types lacks a cast
the debug check in do_div() is over-eager here, because the long long
is always positive in these places. Mark this by casting them to
unsigned long long.
no change in code output:
text data bss dec hex filename
51471 6582 376 58429 e43d sched.o.before
51471 6582 376 58429 e43d sched.o.after
md5:
7f7729c111f185bf3ccea4d542abc049 sched.o.before.asm
7f7729c111f185bf3ccea4d542abc049 sched.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Because of workqueue delay, the put_device could be called before
device_del, so move it to del_conn.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a delayed ACK representing two packets arrives, there are two RTT
samples available, one for each packet. The first (in order of seq
number) will be artificially long due to the delay waiting for the
second packet, the second will trigger the ACK and so will not itself
be delayed.
According to rfc1323, the SRTT used for RTO calculation should use the
first rtt, so receivers echo the timestamp from the first packet in
the delayed ack. For congestion control however, it seems measuring
delayed ack delay is not desirable as it varies independently of
congestion.
The patch below causes seq_rtt and last_ackt to be updated with any
available later packet rtts which should have less (and hopefully
zero) delack delay. The rtt value then gets passed to
ca_ops->pkts_acked().
Where TCP_CONG_RTT_STAMP was set, effort was made to supress RTTs from
within a TSO chunk (!fully_acked), using only the final ACK (which
includes any TSO delay) to generate RTTs. This patch removes these
checks so RTTs are passed for each ACK to ca_ops->pkts_acked().
For non-delay based congestion control (cubic, h-tcp), rtt is
sometimes used for rtt-scaling. In shortening the RTT, this may make
them a little less aggressive. Delay-based schemes (eg vegas, veno,
illinois) should get a cleaner, more accurate congestion signal,
particularly for small cwnds. The congestion control module can
potentially also filter out bad RTTs due to the delayed ack alarm by
looking at the associated cnt which (where delayed acking is in use)
should probably be 1 if the alarm went off or greater if the ACK was
triggered by a packet.
Signed-off-by: Gavin McCullagh <gavin.mccullagh@nuim.ie>
Acked-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're exporting an __init function, oops :-)
The core issue here is that add_preferred_console() is marked
as __init, this makes it impossible to invoke this thing from
a driver probe routine which is what the Sparc serial drivers
need to do.
There is no harm in dropping the __init marker. This code will
actually work properly when invoked from a modular driver,
except that init will probably not pick up the console change
without some other support code.
Then we can drop the __init from sunserial_console_match()
and we're no longer exporting an __init function to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
David Brownell pointed out a regression in my recent "Fix ip command
line processing" patch. It turns out to be a fairly blatant oversight on
my part whereby ic_enable is never set, and thus autoconfiguration is
never enabled. Clearly my testing was broken :-(
The solution that I have is to set ic_enable to 1 if we hit
ip_auto_config_setup(), which basically means that autoconfiguration is
activated unless told otherwise. I then flip ic_enable to 0 if ip=off,
ip=none, ip=::::::off or ip=::::::none using ic_proto_name();
The incremental patch is below, let me know if a non-incremental version
is prepared, as I did as for the original patch to be reverted pending a
fix.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that some PCI-E bridges do the wrong thing in the presense of
CRS Software Visibility and MMCONFIG. In particular, it looks like an
ATI bridge (device ID 7936) will return 0001 in the vendor ID field of
any bridged devices indefinitely.
Not enabling CRS SV avoids the problem, and as we currently do not
really make good use of the feature anyway (we just time out rather than
do any threaded discovery as suggested by the CRS specs), we're better
off just not enabling it.
This should fix a slew of problem reports with random devices (generally
graphics adapters or fairly high-performance networking cards, since it
only affected PCI-E) not getting properly recognized on these AMD systems.
If we really want to use CRS-SV, we may end up eventually needing a
whitelist of systems where this should be enabled, along with some kind
of "pcibios_enable_crs()" query to call the system-specific code.
Suggested-by: Loic Prylli <loic@myri.com>
Tested-by: Kai Ruhnau <kai@tragetaschen.dyndns.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xcryptecb instruction always processes an even number of blocks so
we need to ensure th existence of an extra block if we have to process
an odd number of blocks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Did not fix the reported issue. Apart from other weirdness this causes a
bad link between the TLB flushing logic and the quicklists. If there is
indeed an issue that an arch needs a tlb flush before free then the arch
code needs to set tlb->need_flush before calling quicklist_free.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently the documentation in Documentation/nfsroot.txt was
update to note that in fact ip=off and ip=::::::off as the
latter is ignored and the default (on) is used.
This was certainly a step in the direction of reducing confusion.
But it seems to me that the code ought to be fixed up so that
ip=::::::off actually turns off ip autoconfiguration.
This patch also notes more specifically that ip=on (aka ip=::::::on)
is the default.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move veth.h from net/ to linux/ since it is a user api, and add it to
user header processing Kbuild.
[ Use header-y as suggested by Sam Ravnborg. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a trivial fix of debug message.
When a persist flag is set, the message should say "enabled".
Signed-off-by: Toyo Abe <tabe@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users do "modprobe ip_conntrack hashsize=...". Since we have the
module aliases this loads nf_conntrack_ipv4 and nf_conntrack, the
hashsize parameter is unknown for nf_conntrack_ipv4 however and makes
it fail.
Allow to specify hashsize= for both nf_conntrack and nf_conntrack_ipv4.
Note: the nf_conntrack message in the ringbuffer will display an
incorrect hashsize since nf_conntrack is first pulled in as a
dependency and calculates the size itself, then it gets changed
through a call to nf_conntrack_set_hashsize().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes mac80211 warn (once) when the driver passes up a
frame in which the payload data is not aligned on a four-byte
boundary, with a long comment for people who run into the condition
and need to know what to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station cleanup timer runs every ten seconds, the exact
timing is not relevant at all so it can well run together with
other things to save power.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit fbdcf18df7.
As pointed out by Yanmin Zhang, the problem was already fixed
differently (and correctly), and rather than fix anything, it actually
causes us to create a sub-optimal sched-domains hierarchy (not setting
up the domain belonging to the core) when CONFIG_X86_HT=y.
Requested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 528a572dae ("ide: add ->chipset field
to ide_pci_device_t") broke hwif->chipset setup (it is now set to ide_cmd646
for CMD648 instead of CMD646). It seems that the breakage happend while
I was moving patches around (cmd64x_chipsets[] entries for CMD646 and CMD648
are identical except for 'name' field). Fix it and bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mask 'ireason' variable so only the valid interrupt reason bits
will be reported on "drive appears confused" error.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mask 'ireason' variable with 0x3 so the valid interrupt reason value
is passed to cdrom_write_check_ireason() for checking.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_cd_release() to do the cleanup if ide_cdrom_setup() fails.
It fixes:
- the default drive->dsc_overlap value not being restored
- the default drive->queue's prep_rq_fn not being restored
- struct gendisk 'g' not being freed
- wrong function name being reported on unregister_cdrom() error
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
cdi->mask is cleared by ide_cdrom_register() which is called after the quirk.
Fix it by adding new ->no_speed_select flag to struct ide_cd_config_flags
and using it in ide_cdrom_register() to set CDC_SELECT_SPEED flag.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: New device ID for the CP2101 driver
USB: VID/PID update for sierra
USB: Unbreak fsl_usb2_udc
Commit 5a52bd4a2d introduced a subtle logic
change in tty_wait_until_sent(). The original version would only error out
of the 'do { ... } while (timeout)' loop if signal_pending() evaluated to
true; a timeout or break due to an empty buffer would fall out of the loop
and into the tty->driver->wait_until_sent handling. The current
implementation will error out on either a pending signal or an empty
buffer, falling through to the tty->driver->wait_until_sent handling only
on a timeout.
The ->wait_until_sent() will not be reached if the buffer empties before
timeout jiffies have elapsed. This behavior differs from that prior to commit
5a52bd4a2d.
I turned this up while using a little serial download utility to bootstrap an
ARM-based eval board. The util worked fine on 2.6.22.x, but consistently
failed on 2.6.23.x. Once I'd determined that, I narrowed things down with git
bisect, and found the above difference in logic in tty_wait_until_sent() by
inspection.
This change reverts the logic flow in tty_wait_until_sent() to match that
prior to the aforementioned commit.
Signed-off-by: Cory T. Tusar <ctusar@videon-central.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently when using KCONFIG_ALLCONFIG with randconfig the choice options
are clobbered. As recommended by Roman, this adds an is_new test to see
whether to select a new option or obey the existing one.
This is a resend of the earlier patch a couple of weeks ago, since there
was no reply. Original thread is at http://lkml.org/lkml/2007/11/28/94
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhe Jiang noticed that its possible to underflow pl->events in
prop_norm_percpu() when the value returned by percpu_counter_read() is less
than the error on that read and the period delay > 1. In that case half might
not trigger the batch increment and the value will be identical on the next
iteration, causing the same half to be subtracted again and again.
Fix this by rewriting the division as a single subtraction instead of a
subtraction loop and using percpu_counter_sum() when the value returned by
percpu_counter_read() is smaller than the error.
The latter is still needed if we want pl->events to shrink properly in the
error region.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This stray down would cause a permanent sleep which doesn't seem correct.
The other uses of this semaphore appear fairly mutex like it's even
initialized with init_MUTEX() .. So here a patch for removing this one
down().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to Jeff Moyer for pointing this out.
If the RDWR dentry_open() in ecryptfs_init_persistent_file fails,
it will do a dput/mntput. Need to re-take references if we
retry as RDONLY.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Mike Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should send quota message to netlink only once when hardlimit is
reached. Otherwise user could easily make the system busy by trying to
exceed the hardlimit (and also the messages could be anoying if you cannot
stop writing just now).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix computation of size of skb needed for quota message. We should use
netlink provided functions and not just an ad-hoc number. Also don't print
the return value from nla_put_foo() as it is always -1.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing a cipher name > 32 chars on mount results in an overflow when the
cipher name is printed, because the last character in the struct
ecryptfs_key_tfm's cipher_name string was never zeroed.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
attached please find a new device ID for CP2101 driver. This device is a
usb stick from Dynastream to communicate with ANT wireless devices which
I suppose is fairly similar to the ANT dev board having product id 0x1003.
From: Martin Kusserow <kusserow@ife.ee.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds VID/PID for the MC8775 found internally in the Thinkpad X61s laptop
(and likely others). For commercial reasons the driver maintainer cannot
add VID/PIDs for laptop OEM devices himself.
Signed-off-by: Kevin R Page <linux-kernel@krp.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the change in kobject name handling, the module kobject needs to
have a null release function to ensure that the name it previously set
will be properly cleaned up.
All of this wierdness goes away in 2.6.25 with the rework of the kobject
name and cleanup logic, but this is required for 2.6.24.
Thanks to Alexey Dobriyan for finding the problem, and to Kay Sievers
for pointing out the simple way to fix it after I tried many complex
ways.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an entry for the Userspace I/O framework to MAINTAINERS.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initially transmit buffer pointers were only reset. But buffer
descriptors were possibly still set as ready, and buffer in upper
layer was not freed. This caused driver hang under big load. Now
reset clean properly the buffer descriptor and freed upper layer.
Signed-off-by: Gregory CLEMENT <gclement00@gmail.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Same story as with olympic - htons(readw()) when swab16(readw()) is needed,
missing conversions to le32 when dealing with shared descriptors, etc.
Olympic got those fixes in 2.4.0-test2, 3c359 didn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you need to find a difference between addresses of two
struct members, subtract offsetof() or cast addresses to
char * and subtract those if you prefer it that way. Doing
that same with s/char */u32/, OTOH...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both store MAC address in CIS; there's no decoder for that
type (0x88) so the drivers work with raw data. It is
byteswapped, so ntohs() works for little-endian, but for
big-endian it's wrong. ntohs(le16_to_cpu()) does the
right thing on both (and always expands to swab16()).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* shift before cpu_to_le64(), not after it
* writel() converts to l-e itself
* misc missing conversions
* in set_multicast() hash_table[] is host-endian; we feed it to card
via writel() and populate it as host-endian, so we'd better put the
first element into it also in host-endian
* pci_unmap_single() et.al. expect host-endian, not little-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_unmap_single() and friends getting a little-endian address...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* usb_control_message() to/from stack (breaks on e.g. arm); some
places did kmalloc() for buffer, some just worked from stack.
Added kmalloc()/memcpy()/kfree() in asix_read_cmd()/asix_write_cmd(),
removed that crap from callers.
* Fixed a leak in ax88172_bind() - on success it forgot to kfree() the
buffer.
* Endianness bug in ax88178_bind() - we read a word from eeprom and work with
it without converting to host-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
txlo_dma_addr should be host-endian; we pass it to typhoon_tso_fill(),
which does arithmetics on it, converts to l-e and passes it to card.
Unfortunately, we forgot le32_to_cpu() when initializing it from
face->txLoAddr, which sits in shared memory and is little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
rxBuffCleared is little-endian; we miss le32_to_cpu() in checks for
rx ring overruns.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One cpu_to_le16() too many when passing argument for TYPHOON_CMD_XCVR_SELECT;
we end up passing host-endian while the hardware expects little-endian. The
other place doing that (typhoon_start_runtime()) does the right thing, so the
card will recover at the next ifconfig up/tx timeout/resume, which limits the
amount of mess, but still, WTF?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
in typhoon_get_drvinfo() .parm2 is little-endian; not critical
since we just get the firmware id flipped in get_drvinfo output
on big-endian boxen, but...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
txBytes and rxBytesGood are both 64bit; using le32_to_cpu() won't work
on big-endian for obvious reasons.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Increase the mininum number of partial slabs to keep around and put
partial slabs to the end of the partial queue so that they can add
more objects.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ Regression added by changeset:
cd40b7d398
[NET]: make netlink user -> kernel interface synchronious
-DaveM ]
nl_fib_input re-reuses incoming skb to send the reply. This means that this
packet will be freed twice, namely in:
- netlink_unicast_kernel
- on receive path
Use clone to send as a cure, the caller is responsible for kfree_skb on error.
Thanks to Alexey Dobryan, who originally found the problem.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: intel_cacheinfo.c: cpu cache info entry for Intel Tolapai
x86: fix die() to not be preemptible
After reading the directory contents into the temporary buffer, we grab
each dirent and pass it to filldir witht eh current offset of the dirent.
The current offset was not being set for the first dirent in the temporary
buffer, which coul dresult in bad offsets being set in the f_pos field
result in looping and duplicate entries being returned from readdir.
SGI-PV: 974905
SGI-Modid: xfs-linux-melb:xfs-kern:30282a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
This was broken by my '[XFS] simplify xfs_create/mknod/symlink prototype',
which assigned the re-shuffled ondisk dev_t back to the rdev variable in
xfs_vn_mknod. Because of that i_rdev is set to the ondisk dev_t instead of
the linux dev_t later down the function.
Fortunately the fix for it is trivial: we can just remove the assignment
because xfs_revalidate_inode has done the proper job before unlocking the
inode.
SGI-PV: 974873
SGI-Modid: xfs-linux-melb:xfs-kern:30273a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Andrew "Eagle Eye" Morton noticed that we use raw_local_save_flags()
instead of raw_local_irq_save(flags) in die(). This allows the
preemption of oopsing contexts - which is highly undesirable. It also
causes CONFIG_DEBUG_PREEMPT to complain, as reported by Miles Lane.
this bug was introduced via:
commit 39743c9ef7
Author: Andi Kleen <ak@suse.de>
Date: Fri Oct 19 20:35:03 2007 +0200
x86: use raw locks during oopses
- spin_lock_irqsave(&die.lock, flags);
+ __raw_spin_lock(&die.lock);
+ raw_local_save_flags(flags);
that is not a correct open-coding of spin_lock_irqsave(): both the
ordering is wrong (irqs should be disabled _first_), and the wrong
flags-saving API was used.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When used function put_cmsg() to copy kernel information to user
application memory, if the memory length given by user application is
not enough, by the bad length calculate of msg.msg_controllen,
put_cmsg() function may cause the msg.msg_controllen to be a large
value, such as 0xFFFFFFF0, so the following put_cmsg() can also write
data to usr application memory even usr has no valid memory to store
this. This may cause usr application memory overflow.
int put_cmsg(struct msghdr * msg, int level, int type, int len, void *data)
{
struct cmsghdr __user *cm
= (__force struct cmsghdr __user *)msg->msg_control;
struct cmsghdr cmhdr;
int cmlen = CMSG_LEN(len);
~~~~~~~~~~~~~~~~~~~~~
int err;
if (MSG_CMSG_COMPAT & msg->msg_flags)
return put_cmsg_compat(msg, level, type, len, data);
if (cm==NULL || msg->msg_controllen < sizeof(*cm)) {
msg->msg_flags |= MSG_CTRUNC;
return 0; /* XXX: return error? check spec. */
}
if (msg->msg_controllen < cmlen) {
~~~~~~~~~~~~~~~~~~~~~~~~
msg->msg_flags |= MSG_CTRUNC;
cmlen = msg->msg_controllen;
}
cmhdr.cmsg_level = level;
cmhdr.cmsg_type = type;
cmhdr.cmsg_len = cmlen;
err = -EFAULT;
if (copy_to_user(cm, &cmhdr, sizeof cmhdr))
goto out;
if (copy_to_user(CMSG_DATA(cm), data, cmlen - sizeof(struct cmsghdr)))
goto out;
cmlen = CMSG_SPACE(len);
~~~~~~~~~~~~~~~~~~~~~~~~~~~
If MSG_CTRUNC flags is set, msg->msg_controllen is less than
CMSG_SPACE(len), "msg->msg_controllen -= cmlen" will cause unsinged int
type msg->msg_controllen to be a large value.
~~~~~~~~~~~~~~~~~~~~~~~~~~~
msg->msg_control += cmlen;
msg->msg_controllen -= cmlen;
~~~~~~~~~~~~~~~~~~~~~
err = 0;
out:
return err;
}
The same promble exists in put_cmsg_compat(). This patch can fix this
problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible max_phys_segments violation in cloned dm-crypt bio.
In write operation dm-crypt needs to allocate new bio request
and run crypto operation on this clone. Cloned request has always
the same size, but number of physical segments can be increased
and violate max_phys_segments restriction.
This can lead to data corruption and serious hardware malfunction.
This was observed when using XFS over dm-crypt and at least
two HBA controller drivers (arcmsr, cciss) recently.
Fix it by using bio_add_page() call (which tests for other
restrictions too) instead of constructing own biovec.
All versions of dm-crypt are affected by this bug.
Cc: stable@kernel.org
Cc: dm-crypt@saout.de
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Make sure dm honours max_hw_sectors of underlying devices
We still have no firm testing evidence in support of this patch but
believe it may help to resolve some bug reports. - agk
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Insert a missing KOBJ_CHANGE notification when a device is renamed.
Cc: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
With CONFIG_SCSI=n __scsi_print_sense() is never linked in.
drivers/built-in.o: In function `hp_sw_end_io':
dm-mpath-hp-sw.c:(.text+0x914f8): undefined reference to `__scsi_print_sense'
Caught with a randconfig on current git.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a panic on shrinking a DM device if there is
outstanding I/O to the part of the device that is being removed.
(Normally this doesn't happen - a filesystem would be resized first,
for example.)
The bug is that __clone_and_map() assumes dm_table_find_target()
always returns a valid pointer. It may fail if a bio arrives from the
block layer but its target sector is no longer included in the DM
btree.
This patch appends an empty entry to table->targets[] which will
be returned by a lookup beyond the end of the device.
After calling dm_table_find_target(), __clone_and_map() and target_message()
check for this condition using
dm_target_is_valid().
Sample test script to trigger oops:
Right now it's nearly impossible for parsers that collect kernel crashes
from logs or emails (such as www.kerneloops.org) to detect the
end-of-oops condition. In addition, it's not currently possible to
detect whether or not 2 oopses that look alike are actually the same
oops reported twice, or are truly two unique oopses.
This patch adds an end-of-oops marker, and makes the end marker include
a very simple 64-bit random ID to be able to detect duplicate reports.
Normally, this ID is calculated as a late_initcall() (in the hope that
at that time there is enough entropy to get a unique enough ID); however
for early oopses the oops_exit() function needs to generate the ID on
the fly.
We do this all at the _end_ of an oops printout, so this does not impact
our ability to get the most important portions of a crash out to the
console first.
[ Sidenote: the already existing oopses-since-bootup counter we print
during crashes serves as the differentiator between multiple oopses
that trigger during the same bootup. ]
Tested on 32-bit and 64-bit x86. Artificially injected very early
crashes as well, as expected they result in this constant ID after
multiple bootups:
---[ end trace ca143223eefdc828 ]---
---[ end trace ca143223eefdc828 ]---
because the random pools are still all zero. But it all still works
fine and causes no additional problems (which is the main goal of
instrumentation code).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Realtime tasks would not account their runtime during ticks. Which would lead
to:
struct sched_param param = { .sched_priority = 10 };
pthread_setschedparam(pthread_self(), SCHED_FIFO, ¶m);
while (1) ;
Not showing up in top.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I included these operations vector cases for situations
where we never need to do anything, the entries aren't
filled in by any implementation, so we OOPS trying to
invoke NULL pointer functions.
Really make them NOPs, to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
This operation helper abstracts:
skb->mac_header = skb->data;
but it was done in two more places which were actually:
skb->mac_header = skb->network_header;
and those are corrected here.
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_header update in ipgre_recv() was incorrectly changed to
skb_reset_mac_header() when it was introduced.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places the arguments to the xfrm_audit_start() function are
in the wrong order resulting in incorrect user information being
reported. This patch corrects this by pacing the arguments in the
correct order.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aalgos/ealgos fields are only 32 bits wide. However, af_key tries
to test them with the expression 1 << id where id can be as large as
253. This produces different behaviour on different architectures.
The following patch explicitly checks whether ID is greater than 31
and fails the check if that's the case.
We cannot easily extend the mask to be longer than 32 bits due to
exposure to user-space. Besides, this whole interface is obsolete
anyway in favour of the xfrm_user interface which doesn't use this
bit mask in templates (well not within the kernel anyway).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In arp_process() (net/ipv4/arp.c), there is unused code: definition
and assignment of tha (target hw address ).
Signed-off-by: Mark Ryden <markryde@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if log_len is larger than 4K then we are killing the stack.
allocate on heap instead and limit size to what practically can
be used (PAGE_SIZE)
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves _cancel_deferred_work out of mutex protection and removes
unnecessary mutex in pci_suspend and pci_resume.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tg3_nvram_write_block_unbuffered() is reading data from nvram into
allocated buffer before overwriting a part of it with user-supplied
data. Then it feeds the entire page back to nvram. It should be
storing the words it had read as little-endian, not as host-endian.
Note that tg3_set_eeprom() does exactly that for padding the same
data to full words before it gets passed down to tg3_nvram_write_block()
and then to tg3_nvram_write_block_unbuffered().
Moreover, when we get to sending the entire thing back to nvram, we
go through it word-by-word, doing essentially
writel(swab32(le32_to_cpu(word)), ...)
so if we want them to reach the card in host-independent endianness,
we'd better really have all that buffer filled with fixed-endian.
For user-supplied part we obviously do have that (it's an array of
octets memcpy'd in), ditto for padding of user-supplied part to word
boundaries (taken care of in tg3_set_eeprom()). The rest of the
buffer gets filled by tg3_nvram_write_block_unbuffered() and it would
damn better be consistent with that (and with tg3_get_eeprom(), while
we are at it - there we also convert the words read from nvram to
little-endian before returning the buffer to user).
The bug should get triggered on big-endian boxen when set_eeprom is done
for less than entire page. Then the words that should've been unaffected
at all will actually get byteswapped in place in nvram.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed misannotations, introduced a new helper - tg3_nvram_read_le().
It gets __le32 * instead of u32 * and puts there the value converted
to little-endian. A lot of callers of tg3_nvram_read() were doing
that; converted them to tg3_nvram_read_le().
At that point the driver is practically endian-clean; the only remaining
place is an actual bug, AFAICS; will be dealt with in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix inappropriate memory freeing in case of requested rate_control_ops was
not found. In this case the list head entity is going to be accidentally
wasted.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using recvfrom() on a SOCK_DGRAM packet socket, I noticed that the MAC
address passed back for wireless frames was always completely wrong. The
reason for this is that the header parse function assigned to our virtual
interfaces is a function parsing an 802.11 rather than 802.3 header. This
patch fixes it by keeping the default ethernet header operations assigned.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in staying in IEEE80211_ASSOCIATED if there is no
sta_info entry to receive frames with.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Adjust CMCI mask on CPU hotplug
[IA64] make flush_tlb_kernel_range() an inline function
[IA64] Guard elfcorehdr_addr with #if CONFIG_PROC_FS
[IA64] Fix Altix BTE error return status
[IA64] Remove assembler warnings on head.S
[IA64] Remove compiler warinings about uninitialized variable in irq_ia64.c
[IA64] set_thread_area fails in IA32 chroot
[IA64] print kernel release in OOPS to make kerneloops.org happy
[IA64] Two trivial spelling fixes
[IA64] Avoid unnecessary TLB flushes when allocating memory
[IA64] ia32 nopage
[IA64] signal: remove redundant code in setup_sigcontext()
IA64: Slim down __clear_bit_unlock
ps3fb: Update for firmware 2.10
As of PS3 firmware version 2.10, the GPU command buffer size must be at least 2
MiB large. Since we use only a small part of the GPU command buffer and don't
want to waste precious XDR memory, move the GPU command buffer back to the
start of the XDR memory reserved for ps3fb and let the unused part overlap with
the actual frame buffer.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Oledzki noticed a dirty page accounting leak on some of his
machines, causing the machine to eventually lock up when the kernel
decided that there was too much dirty data, but nobody could actually
write anything out to fix it.
The culprit turns out to be filesystems (cough ext3 with data=journal
cough) that re-dirty the page when the "->invalidatepage()" callback is
called.
Fix it up by doing a final dirty page accounting check when we actually
remove the page from the page cache.
This fixes bugzilla entry 9182:
http://bugzilla.kernel.org/show_bug.cgi?id=9182
Tested-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Krzysztof Oledzki <olel@ans.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes an unused variable warning in mm/vmalloc.c.
Tony: also fix resulting fallout in uncached.c with a
typo in args to flush_tlb_kernel_range().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Access to elfcorehdr_addr needs to be guarded by #if CONFIG_PROC_FS
as well as the existing #if guards.
Fixes the following build problem:
arch/ia64/hp/common/built-in.o: In function
`sba_init':arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
:arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Altix shub2 BTE error detail bits are in a different location
than on shub1. The current code does not take this into account
resulting in all shub2 BTE failures mapping to "unknown".
This patch reads the error detail bits from the proper location,
so the correct BTE failure reason is returned for both shub1
and shub2.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following assembler warning messages.
AS arch/ia64/kernel/head.o
arch/ia64/kernel/head.S: Assembler messages:
arch/ia64/kernel/head.S:1179: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1179: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
arch/ia64/kernel/head.S:1180: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1180: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
:
arch/ia64/kernel/head.S:1213: Warning: Use of 'ldf.fill.nta' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1213: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following compiler warning messages.
CC arch/ia64/kernel/irq_ia64.o
arch/ia64/kernel/irq_ia64.c: In function 'create_irq':
arch/ia64/kernel/irq_ia64.c:343: warning: 'domain.bits[0u]' may be used uninitialized in this function
arch/ia64/kernel/irq_ia64.c: In function 'assign_irq_vector':
arch/ia64/kernel/irq_ia64.c:203: warning: 'domain.bits[0u]' may be used uninitialized in this function
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I tried to upgrade an IA32 chroot on my IA64 to a new glibc with TLS.
It kept dying because set_thread_area was returning -ESRCH
(bugs.debian.org/451939).
I instrumented arch/ia64/ia32/sys_ia32.c:get_free_idx() and ended up
seeing output like
[pid] idx desc->a desc->b
-----------------------------
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> 0 0
[2710] 2 -> 0 0
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> c6b0ffff 40dff31b
[2710] 2 -> 0 0
[2711] 0 -> c6b0ffff 40dff31b
[2711] 1 -> c6b0ffff 40dff31b
[2711] 2 -> 48c0ffff 40dff317
which suggested to me that TLS pointers were surviving exec() calls,
leading to GDT pointers filling up and the eventual failure of
get_free_idx().
I think the solution is flushing the tls array on exec.
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64 oops message doesn't include the kernel version, which
makes it hard to automatically categorize oops messages scraped
from mailing lists and bug databases.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Improve performance of memory allocations on ia64 by avoiding a global TLB
purge to purge a single page from the file cache. This happens whenever we
evict a page from the buffer cache to make room for some other allocation.
Test case: Run 'find /usr -type f | xargs cat > /dev/null' in the
background to fill the buffer cache, then run something that uses memory,
e.g. 'gmake -j50 install'. Instrumentation showed that the number of
global TLB purges went from a few millions down to about 170 over a 12
hours run of the above.
The performance impact is particularly noticeable under virtualization,
because a virtual TLB is generally both larger and slower to purge than
a physical one.
Signed-off-by: Christophe de Dinechin <ddd@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some redundant code in the function setup_sigcontext().
The registers ar.ccv,b7,r14,ar.csd,ar.ssd,r2-r3 and r16-r31 are not
restored in restore_sigcontext() when (flags & IA64_SC_FLAG_IN_SYSCALL) is
true. So we don't need to zero those variables in setup_sigcontext().
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
__clear_bit_unlock does not need to perform atomic operations on the
variable. Avoid a cmpxchg and simply do a store with release semantics.
Add a barrier to be safe that the compiler does not do funky things.
Tony: Use intrinsic rather than inline assembler
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
patch: [SCSI] initio: convert to use the data buffer accessors had a
small but fatal bug in that it didn't increment the pointer into the
initio scatterlist descriptors as it looped over the block generated
ones. Fixed here.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
> I have a scanner connected to a Initio INI-950 SCSI card and I recently
> upgraded from SuSE 10.2 to 10.3. The new kernel doesn't see any of my
> devices. I get the following in /var/log/messages:
>
> ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16
> initio: I/O port range 0x0 is busy.
> ACPI: PCI interrupt for device 0000:00:0a.0 disabled
Humm not a collision - thats a bug in the driver updating. Looks like the
changes I made and combined with Christoph's lost a line somewhere when I
was merging it all.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The patch described by the following excerpt from ChangeLog-2.6.24-rc1
eventually causes a "irq X: nobody cared" error after a while:
commit 99c9e0a1d6
Author: Matthew Wilcox <matthew@wil.cx>
Date: Fri Oct 5 15:55:12 2007 -0400
[SCSI] sym53c8xx: Make interrupt handler capable of returning IRQ_NONE
After this happens, the kernel disables the IRQ, causing the SCSI card
to stop working until the next reboot. The problem is caused by the
interrupt handler returning IRQ_NONE instead of IRQ_HANDLED after
handling an interrupt-on-the-fly (INTF) condition. The following patch
fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This fixes a potential corruption bug where the truncation would cause
reading or writing to the wrong memory area on machines with >4GB of
main memory.
Cc: Stable Kernel Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following commit changed the pointer passed to request_irq(), but
failed to change the pointer passed to free_irq():
commit 99c9e0a1d6
Author: Matthew Wilcox <matthew@wil.cx>
Date: Fri Oct 5 15:55:12 2007 -0400
[SCSI] sym53c8xx: Make interrupt handler capable of returning IRQ_NONE
...
The result is that free_irq() doesn't actually take any action. This
patch fixes it.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
this is the tale of a full day spent debugging an ancient but elusive bug.
after booting up thousands of random .config kernels, i finally happened
to generate a .config that produced the following rare bootup failure
on 32-bit x86:
| ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
| ..MP-BIOS bug: 8254 timer not connected to IO-APIC
| ...trying to set up timer (IRQ0) through the 8259A ... failed.
| ...trying to set up timer as Virtual Wire IRQ... failed.
| ...trying to set up timer as ExtINT IRQ... failed :(.
| Kernel panic - not syncing: IO-APIC + timer doesn't work! Boot with apic=debug
| and send a report. Then try booting with the 'noapic' option
this bug has been reported many times during the years, but it was never
reproduced nor fixed.
the bug that i hit was extremely sensitive to .config details.
First i did a .config-bisection - suspecting some .config detail.
That led to CONFIG_X86_MCE: enabling X86_MCE magically made the bug disappear
and the system would boot up just fine.
Debugging my way through the MCE code ended up identifying two unlikely
candidates: the thing that made a real difference to the hang was that
X86_MCE did two printks:
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
Adding the same printks to a !CONFIG_X86_MCE kernel made the bug go away!
this left timing as the main suspect: i experimented with adding various
udelay()s to the arch/x86/kernel/io_apic_32.c:check_timer() function, and
the race window turned out to be narrower than 30 microseconds (!).
That made debugging especially funny, debugging without having printk
ability before the bug hits is ... interesting ;-)
eventually i started suspecting IRQ activities - those are pretty much the
only thing that happen this early during bootup and have the timescale of
a few dozen microseconds. Also, check_timer() changes the IRQ hardware
in various creative ways, so the main candidate became IRQ0 interaction.
i've added a counter to track timer irqs (on which core they arrived, at
what exact time, etc.) and found that no timer IRQ would arrive after the
bug condition hits - even if we re-enable IRQ0 and re-initialize the i8259A,
but that we'd get a small number of timer irqs right around the time when we
call the check_timer() function.
Eventually i got the following backtrace triggered from debug code in the
timer interrupt:
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ...
Pid: 1, comm: swapper Not tainted (2.6.24-rc5 #57)
EIP: 0060:[<c044d57e>] EFLAGS: 00000246 CPU: 0
EIP is at _spin_unlock_irqrestore+0x5/0x1c
EAX: c0634178 EBX: 00000000 ECX: c4947d63 EDX: 00000246
ESI: 00000002 EDI: 00010031 EBP: c04e0f2e ESP: f7c41df4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: ffe04000 CR3: 00630000 CR4: 000006d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c05f5784>] setup_IO_APIC+0x9c3/0xc5c
the spin_unlock() was called from init_8259A(). Wait ... we have an IRQ0
entry while we are in the middle of setting up the local APIC, the i8259A
and the PIT??
That is certainly not how it's supposed to work! check_timer() was supposed
to be called with irqs turned off - but this eroded away sometime in the
past. This code would still work most of the time because this code runs
very quickly, but just the right timing conditions are present and IRQ0
hits in this small, ~30 usecs window, timer irqs stop and the system does
not boot up. Also, given how early this is during bootup, the hang is
very deterministic - but it would only occur on certain machines (and
certain configs).
The fix was quite simple: disable/restore interrupts properly in this
function. With that in place the test-system now boots up just fine.
(64-bit x86 io_apic_64.c had the same bug.)
Phew! One down, only 1500 other kernel bugs are left ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit 76d2160147 lazy irq disabling
was implemented, and the simple irq handler had a masking set to it.
Remy Bohmer discovered that some devices in the ARM architecture
would trigger the mask, but never unmask it. His patch to do the
unmasking was questioned by Russell King about masking simple irqs
to begin with. Looking further, it was discovered that the problems
Remy was seeing was due to improper use of the simple handler by
devices, and he later submitted patches to fix those. But the issue
that was uncovered was that the simple handler should never mask.
This patch reverts the masking in the simple handler.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch introducing this left out 64-bit x86 despite it also having
extra entries.
this solves Xen guest troubles.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Kprobes for x86-64 may cause a kernel crash if it inserted on "iret"
instruction. "call absolute" is invalid on x86-64, so we don't need
treat it.
- Change the processing order as same as x86-32.
- Add "iret"(0xcf) case.
- Remove next_rip local variable.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
jprobe for x86-64 may cause kernel page fault when the jprobe_return()
is called from incorrect function.
- Use jprobe_saved_regs instead getting it from stack.
(Especially on x86-64, it may get incorrect data, because
pt_regs can not be get by using container_of(rsp))
- Change the type of stack pointer to unsigned long *.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:
...
WARNING: vmlinux.o(.text+0x41cd3): Section mismatch: reference to .init.data:tvec_base_done.22610 (between 'timer_cpu_notify' and 'run_timer_softirq')
WARNING: vmlinux.o(.text+0x41d67): Section mismatch: reference to .init.data:tvec_base_done.22610 (between 'timer_cpu_notify' and 'run_timer_softirq')
...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add unlocked version for use by irq_chip.set_type handlers which may
wish to change handler to level or edge handler when IRQ type is
changed.
The normal set_irq_handler() call cannot be used because it tries to
take irq_desc.lock which is already held when the irq_chip.set_type
hook is called.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Resolve the following regression of a choppy, almost unusable laptop:
http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525
A previous version of the code did the reprogramming of the broadcast
device in the return from idle code. This was removed, but the logic in
tick_handle_oneshot_broadcast() was kept the same.
When a broadcast interrupt happens we signal the expiry to all CPUs
which have an expired event. If none of the CPUs has an expired event,
which can happen in dyntick mode, then we reprogram the broadcast
device. We do not reprogram otherwise, but this is only correct if all
CPUs, which are in the idle broadcast state have been woken up.
The code ignores, that there might be pending not yet expired events on
other CPUs, which are in the idle broadcast state. So the delivery of
those events can be delayed for quite a time.
Change the tick_handle_oneshot_broadcast() function to check for CPUs,
which are in broadcast state and are not woken up by the current event,
and enforce the rearming of the broadcast device for those CPUs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is for controlling the upper 32bits of the event ctrl msrs.
This includes the upper 4 bits of the event select and the Guest Only and
Host Only bits
This patch is necessary to make Event Based Profiling work reliably on a
Family 10h processor
[akpm@linux-foundation.org: checkpatch.pl fixes]
Signed-off-by: Barry Kasindorf <barry.kasindorf@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: do not hurt SCHED_BATCH on wakeup
sched: touch softlockup watchdog after idling
sched: sysctl, proc_dointvec_minmax() expects int values for
sched: mark rwsem functions as __sched for wchan/profiling
sched: fix crash on ia64, introduce task_current()
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Cleanup umem driver: fix most checkpatch warnings, conform to kernel
block: let elv_register() return void
as-iosched: fix write batch start point
as-iosched: fix incorrect comments
block: use jiffies conversion functions in scsi_ioctl.c
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Put the correct offset in dirent d_off
[XFS] Don't wait for pending I/Os when purging blocks beyond eof.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: remove unused 'mode' from the mmc_host structure
sdhci: support JMicron JMB38x chips
sdhci: use PIO when DMA can't satisfy the request
sdhci: don't warn about sdhci 2.0 controllers
sdhci: describe quirks
measurements by Yanmin Zhang have shown that SCHED_BATCH tasks benefit
if they run the same place_entity() logic as SCHED_OTHER tasks - so
uniformize behavior in this area.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
min_sched_granularity_ns, max_sched_granularity_ns,
min_wakeup_granularity_ns and max_wakeup_granularity_ns are declared
"unsigned long".
This is incorrect since proc_dointvec_minmax() expects plain "int" guard
values.
This bug only triggers on big endian 64 bit arches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This following commit
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fdf8cb0909b531f9ae8f9b9d7e4eb35ba3505f07
un-inlined a low-level rwsem function, but did not mark it as __sched.
The result is that it now shows up as thread wchan (which also affects
/proc/profile stats). The following simple patch fixes this by properly
marking rwsem_down_failed_common() as a __sched function.
Also in this patch, which is up for discussion, marks down_read() and
down_write() proper as __sched. For profiling, it is pretty much
useless to know that a semaphore is beig help - it is necessary to know
_which_ one. By going up another frame on the stack, the information
becomes much more useful.
In summary, the below change to lib/rwsem.c should be applied; the
changes to kernel/rwsem.c could be applied if other kernel hackers agree
with my proposal that down_read()/down_write() in the profile is not
enough.
[ akpm@linux-foundation.org: build fix ]
Signed-off-by: Livio Soares <livio@eecg.toronto.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some services (e.g. sched_setscheduler(), rt_mutex_setprio() and
sched_move_task()) must handle a given task differently in case it's the
'rq->curr' task on its run-queue. The task_running() interface is not
suitable for determining such tasks for platforms with one of the
following options:
#define __ARCH_WANT_UNLOCKED_CTXSW
#define __ARCH_WANT_INTERRUPTS_ON_CTXSW
Due to the fact that it makes use of 'p->oncpu == 1' as a criterion but
such a task is not necessarily 'rq->curr'.
The detailed explanation is available here:
https://lists.linux-foundation.org/pipermail/containers/2007-December/009262.html
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Tested-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
coding style.
linux-2.6.24-rc5-git3> checkpatch.pl-next patches/block-umem-ckpatch.patch
total: 0 errors, 5 warnings, 530 lines checked
All of these are line-length warnings.
Only change in generated object file is due to not initializing a
static global variable to 0.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
elv_register() always returns 0, and there isn't anything it does where
it should return an error (the only error condition is so grave that
it's handled with a BUG_ON).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
New write batches currently start from where the last one completed.
We have no idea where the head is after switching batches, so this
makes little sense. Instead, start the next batch from the request
with the earliest deadline in the hope that we avoid a deadline
expiry later on.
Signed-off-by: Aaron Carroll <aaronc@gelato.unsw.edu.au>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use msecs_to_jiffies() and jiffies_to_msecs() in scsi_ioctl().
Sometimes callers use very large values for e.g. vendor specific media
clear command and calculation can overflow.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The recent filldir regression fix was not putting the correct d_off in
each dirent. This was resulting in incorrect cookies being passed to dmapi
ioctls and the wrong offset appearing in the dirents. readdir was
unaffected as the filp->f_pos was being updated with the correct offset
and this was being written into the last dirent in each buffer. Fix the
XFS code to do the right thing.
SGI-PV: 973746
SGI-Modid: xfs-linux-melb:xfs-kern:30240a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
On last close of a file we purge blocks beyond eof. The same code is used
when we truncate the file size down. In this case we need to wait for any
pending I/Os for dirty pages beyond the new eof. For the last close case
we are not changing the file size and therefore do not need to wait for
any I/Os to complete. This fixes a performance bottleneck where writes
into the page cache and cache flushes can become mutually exclusive.
SGI-PV: 964002
SGI-Modid: xfs-linux-melb:xfs-kern:30220a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Peter Leckie <pleckie@sgi.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: fix ATAPI draining
libata: update atapi_eh_request_sense() such that lbam/lbah contains buffer size
libata-acpi: implement _GTF command filtering
libata-acpi: improve _GTF execution error handling and reporting
libata-acpi: improve ACPI disabling
libata-acpi: implement dev->gtf_cache and evaluate _GTF right after _STM during resume
libata-acpi: implement and use ata_acpi_init_gtm()
libata-acpi: add new hooks ata_acpi_dissociate() and ata_acpi_on_disable()
libata: ata_dev_disable() should be called from EH context
libata: add more opcodes to ata.h
libata: update ata_*_printk() macros such that level can be a variable
libata-acpi: adjust constness in ata_acpi_gtm/stm() parameters
sata_mv: improve warnings about Highpoint RocketRAID 23xx cards
libata: add ST3160023AS / 3.42 to NCQ blacklist
libata: clear link->eh_info.serror from ata_std_postreset()
sata_sil: fix spurious IRQ handling
This reverts commit 54f9f80d65 ("hugetlb:
Add hugetlb_dynamic_pool sysctl")
Given the new sysctl nr_overcommit_hugepages, the boolean dynamic pool
sysctl is not needed, as its semantics can be expressed by 0 in the
overcommit sysctl (no dynamic pool) and non-0 in the overcommit sysctl
(pool enabled).
(Needed in 2.6.24 since it reverts a post-2.6.23 userspace-visible change)
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hugetlb: introduce nr_overcommit_hugepages sysctl
While examining the code to support /proc/sys/vm/hugetlb_dynamic_pool, I
became convinced that having a boolean sysctl was insufficient:
1) To support per-node control of hugepages, I have previously submitted
patches to add a sysfs attribute related to nr_hugepages. However, with
a boolean global value and per-mount quota enforcement constraining the
dynamic pool, adding corresponding control of the dynamic pool on a
per-node basis seems inconsistent to me.
2) Administration of the hugetlb dynamic pool with multiple hugetlbfs
mount points is, arguably, more arduous than it needs to be. Each quota
would need to be set separately, and the sum would need to be monitored.
To ease the administration, and to help make the way for per-node
control of the static & dynamic hugepage pool, I added a separate
sysctl, nr_overcommit_hugepages. This value serves as a high watermark
for the overall hugepage pool, while nr_hugepages serves as a low
watermark. The boolean sysctl can then be removed, as the condition
nr_overcommit_hugepages > 0
indicates the same administrative setting as
hugetlb_dynamic_pool == 1
Quotas still serve as local enforcement of the size of the pool on a
per-mount basis.
A few caveats:
1) There is a race whereby the global surplus huge page counter is
incremented before a hugepage has allocated. Another process could then
try grow the pool, and fail to convert a surplus huge page to a normal
huge page and instead allocate a fresh huge page. I believe this is
benign, as no memory is leaked (the actual pages are still tracked
correctly) and the counters won't go out of sync.
2) Shrinking the static pool while a surplus is in effect will allow the
number of surplus huge pages to exceed the overcommit value. As long as
this condition holds, however, no more surplus huge pages will be
allowed on the system until one of the two sysctls are increased
sufficiently, or the surplus huge pages go out of use and are freed.
Successfully tested on x86_64 with the current libhugetlbfs snapshot,
modified to use the new sysctl.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ecryptfs in 2.6.24-rc3 wasn't surviving fsx for me at all, dying after 4
ops. Generally, encountering problems with stale data and improperly
zeroed pages. An extending truncate + write for example would expose stale
data.
With the changes below I got to a million ops and beyond with all mmap ops
disabled - mmap still needs work. (A version of this patch on a RHEL5
kernel ran for over 110 million fsx ops)
I added a few comments as well, to the best of my understanding
as I read through the code.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bloat-o-meter assumes that a '.' anywhere in a symbol's name means that it
is static and prepends 'static.' to the first part of the symbol name,
discarding the portion of the name that follows the '.'. However, the
names of function entry points begin with '.' in the ppc64 ABI. This
causes all function text size changes to be accounted to a single 'static.'
entry in the output when comparing ppc64 kernels.
Change getsizes() to ignore the first character of the symbol name when
searching for '.'.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few fixups from Andrew's code comments.
- removed "static inline" forward-declares
- changed use of min() to min_t()
- removed some unnecessary NULL initializations
- removed a couple of BUG() calls
Fixes this:
drivers/dma/ioat_dma.c: In function `ioat1_tx_submit':
drivers/dma/ioat_dma.c:177: sorry, unimplemented: inlining failed in call to '__ioat1_dma_memcpy_issue_pending': function body not available
drivers/dma/ioat_dma.c:268: sorry, unimplemented: called from here
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eCryptfs wasn't setting s_blocksize in it's superblock; just pick it up
from the lower FS. Having an s_blocksize of 0 made things like "filefrag"
which call FIGETBSZ unhappy.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Mike Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases the IO subsystem is able to merge requests if the pages are
adjacent in physical memory. This was achieved in the allocator by having
expand() return pages in physically contiguous order in situations were a
large buddy was split. However, list-based anti-fragmentation changed the
order pages were returned in to avoid searching in buffered_rmqueue() for a
page of the appropriate migrate type.
This patch restores behaviour of rmqueue_bulk() preserving the physical
order of pages returned by the allocator without incurring increased search
costs for anti-fragmentation.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark Lord <mlord@pobox.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These types define the size of data read from /dev/apm_bios. They should
not be hidden behind #ifdef __KERNEL__.
This is killing my xserver compile, apm_event_t is used in the xserver
source.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpufreq_stats_free_table() mustn't be __cpuexit since it's called by the
__cpuinit cpufreq_stat_cpu_callback().
This patch fixes the following section mismatch reported by
Chris Clayton:
WARNING: vmlinux.o(.init.text+0x143dd): Section mismatch: reference to .exit.text:cpufreq_stats_free_table (between 'cpufreq_stat_cpu_callback' and 'cpufreq_stats_init')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Chris Clayton <chris2553@googlemail.com>
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error handling code should undo the ioremap as well.
The problem was detected using the following semantic match
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2;
constant C;
int ret;
@@
T E;
...
* E = ioremap(...);
if (E == NULL) S
... when != iounmap(E)
when != if (E != NULL) { ... iounmap(E); ...}
when != x1 = (T1)E
if (...) {
... when != iounmap(E)
when != if (E != NULL) { ... iounmap(E); ...}
when != x2 = (T2)E
(
* return;
|
* return C;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve the error handling for mm/sparse.c::sparse_add_one_section(). And I
see no reason to check 'usemap' until holding the 'pgdat_resize_lock'.
[geoffrey.levand@am.sony.com: sparse_index_init() returns -EEXIST]
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo hit some BUG_ONs that were probably caused by these missing unlocks
causing an unbalance. He couldn't reproduce the bug reliably, so it's
unknown that it's definitly fixing the problem he hit, but it's a fairly
good chance, and this fixes an obvious bug.
[ Dave: "Ingo followed up that he hit some lockdep related output with
this applied, so it may not be right. I'll look at it after
xmas if no-one has it figured out before then."
Akpm: "It looks pretty correct to me though." ]
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes some of the alpha-specific build problems, except a) modpost
warning about COMMON symbol "saved_config" and b) nasty final link
failure with gcc-4.x, -Os and scsi-disk driver configured built-in
(due to jump table in .rodata referencing discarded .exit.text).
- build failure with gcc-4.2.x: fix up casts in cia_io* routines to avoid
warnings ('discards qualifiers from pointer target type'), which are
failures, thanks to -Werror;
- modpost warnings: add missing __init qualifier for titan and marvel;
for non-generic build, move machine vectors from .data to .data.init.refok
section;
- unbreak CPU-specific optimization: rearrange cpuflags-y assignments
so that extended -mcpu value (ev56, pca56, ev67) overrides basic
one (ev5, ev6) and not vice versa.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it turns out, the kernel divides by EXT3_INODES_PER_GROUP(s) when
mounting an ext3 filesystem. If that number is zero, a crash follows.
Below a patch.
This crash was reported by Joeri de Ruiter, Carst Tankink and Pim Vullers.
Cc: <linux-ext4@vger.kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPARSEMEM_VMEMMAP needs to be a selectable config option to support
building the kernel both with and without sparsemem vmemmap support. This
selection is desirable for platforms which could be configured one way for
platform specific builds and the other for multi-platform builds.
Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ecryptfs_destroy_mount_crypt_stat() checks whether each
auth_tok->global_auth_tok_key is nonzero and if so puts that key. However,
in some early mount error paths nothing has initialized the pointer, and we
try to key_put() garbage. Running the bad cipher tests in the testsuite
exposes this, and it's happy with the following change.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While auditing proc_doulongvec_ms_jiffies_minmax() usage in kernel, I found
a bug in drivers/parport/procfs.c, incorrectly using sizeof(int) instead of
sizeof(unsigned long)
Only 64bit arches are affected by this old bug.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First of all, thanks to Bob Tracy <rct@frus.com> and
Michael Cree <mcree@orcon.net.nz> for testing.
Especially to Bob, as he has done titanic multi-day git-bisect
work that finally helped to reproduce and nail down the bug
(http://bugzilla.kernel.org/show_bug.cgi?id=9457).
[ev6-]stxncpy.S: it's t12, not t2 register that is supposed to contain
the last byte offset upon return. As a result of wrong register use
(which was my fault back in 2003, IIRC), under some circumstances extra
terminating zero bytes were added to destination string. This particularly
led to incorrect DEVPATH strings generated in uevent and therefore to udev
problems.
strncpy.S: unrelated bug I found while testing the above fix - destination
is not properly zero-padded then a byte count exceeds source length.
Actually this is addition to strncpy fix from last year.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Bob Tracy <rct@frus.com>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes when UML is debugged gdb miss breakpoints.
When process traced by gdb do fork, debugger remove breakpoints from
child address space. There is possibility to trace more than one fork,
but this not work with UML, I guess (only guess) there is a deadlock -
gdb waits for UML and UML waits for gdb.
When clone() is called with SIGCHLD and CLONE_VM flags, gdb see this
as PTRACE_EVENT_FORK not as PTRACE_EVENT_CLONE and remove breakpoints
from child and at the same time from traced process, because either
have the same address space.
Maybe it is possible to do fix in gdb, but I'm not sure if there is
easy way to find out if traced and child processes share memory. So I
do fix for UML, it simply do not call clone() with both SIGCHLD and
CLONE_VM flags together. Additionally __WALL flag is used for
waitpid() to assure not miss clone and normal process events.
[ jdike - checkpatch fixes ]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make[3]: *** No rule to make target `/usr/src/devel/include/linux/ticable.h', needed by `/usr/src/devel/usr/include/linux/ticable.h'. Stop.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With ATAPI transfer chunk size properly programmed, libata PIO HSM
should be able to handle full spurious data chunks. Also, it's a good
idea to suppress trailing data warning for misc ATAPI commands as
there can be many of them per command - for example, if the chunk size
is 16 and the drive tries to transfer 510 bytes, there can be 31
trailing data messages.
This patch makes the following updates to libata ATAPI PIO HSM
implementation.
* Make it drain full spurious chunks.
* Suppress trailing data warning message for misc commands.
* Put limit on how many bytes can be drained.
* If odd, round up consumed bytes and the number of bytes to be
drained. This gets the number of bytes to drain right for drivers
which do 16bit PIO.
This patch is partial backport of improve-ATAPI-data-xfer patchset
pending for #upstream.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While updating lbam/h for ATAPI commands, atapi_eh_request_sense() was
left out. Update it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTF command filtering which can be controlled by
libata.acpi_filter kernel parameter. Currently SETXFER and LOCK
commands are filtered.
libata configures transfer mode by itself and _GTF SETXFER commands
can potentially disrupt device configuration. _GTM/_STM mechanism
can't handle hotplugging too well and when _GTF is executed,
controller is in PIO0 rather than the mode _STM configured.
Note that detecting SET MAX LOCK requires looking at the previous
command. This adds a bit to code complexity.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As _GTF commands can't transfer data, device error never signals
transfer error. It indicates that the device vetoed the operation, so
it's meaningless to retry.
This patch makes libata-acpi to report and continue on device errors
when executing _GTF commands. Also commands rejected by device don't
contribute to the number of _GTF commands executed.
While at it, update _GTF execution reporting such that all successful
commands are logged at KERN_DEBUG and rename taskfile_load_raw() to
ata_acpi_run_tf() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If _GTF evalution fails, it's pointless to retry. If nothing else
is wrong, just ignore the error.
* After disabling ACPI, return success iff the number of executed _GTF
command equals zero. Otherwise, tell EH to retry. This change
fixes bogus 1 return bug where ata_acpi_on_devcfg() expects the
caller to reload IDENTIFY data and continue but the caller
interprets it as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain implementations, _GTF evaluation depends on preceding _STM
and both can be pretty picky about the configuration. Using _GTM
result cached during controller initialization satisfies the most
neurotic _STM implementation. However, libata evaluates _GTF after
reset during device configuration and the hardware state can be
different from what _GTF expects and can cause evaluation failure.
This patch adds dev->gtf_cache and updates ata_dev_get_GTF() such that
it uses the cached value if available. Cache is cleared with a call
to ata_acpi_clear_gtf().
Because for SATA ACPI nodes _GTF must be evaluated after _SDD which
can't be done till IDENTIFY is complete, _GTF caching from
ata_acpi_on_resume() is used only for IDE ACPI nodes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
_GTM fetches currently configured transfer mode while _STM configures
controller according to _GTM parameter and prepares transfer mode
configuration TFs for _GTF. In many cases _GTM and _STM
implementations are quite brittle and can't cope with configuration
changed by libata.
libata does not depend on ATA ACPI to configure devices. The only
reason libata performs _GTM and _STM are to make _GTF evaluation
succeed and libata also doesn't care about how _GTF TFs configure
transfer mode. It overrides that configuration anyway, so from
libata's POV, it doesn't matter what value is feeded to _STM as long
as evaluation succeeds for _STM and following _GTF.
This patch adds dev->__acpi_init_gtm and store initial _GTM values on
host initialization before modified by reset and mode configuration.
If the field is valid, ata_acpi_init_gtm() returns pointer to the
saved _GTM structure; otherwise, NULL.
This saved value is used for _STM during resume and peek at
BIOS/firmware programmed initial timing for later use. The accessor
is there to make building w/o ACPI easy as dev->__acpi_init doesn't
exist if ACPI is not enabled.
On driver detach, the initial BIOS configuration is restored by
executing _STM with the initial _GTM values such that the next driver
can also use the initial BIOS configured values.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add two hooks - ata_acpi_dissociate() which is called during driver
detach after the whole host is shutdown and ata_acpi_on_disable()
which is called when a device is disabled.
Signed-off-by: Tejun heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_detach() calls ata_dev_disable() with host lock held but
ata_dev_disable() should be called from EH context. ata_port_detach()
steals EH context by setting ATA_PFLAG_UNLOADAING and flushing EH.
Drop locking around ata_dev_disable() and note that ata_port_detach()
owns EH context at that point.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add constants for DEVICE CONFIGURATION OVERLAY and SET_MAX to
include/linux/ata.h.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make prink helpers format @lv together rather than prepending to the
format string as constant.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* No internal function uses const ata_port. Drop const from @ap.
* Make ata_acpi_stm() copy @stm before using it and change @stm to
const.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.
Harmless to us, but very useful for end users.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ. It also should
be cleared after reset just like SError itself.
Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge. Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.
* On SATA PHY event interrupt, serror value is checked to see whether
it really is PHYRDY CHG event. If not, SATA PHY event interrupt is
ignored.
* If ATA interrupt occurs while no command is in progress, it's
cleared and ignored.
This fixes bugzilla bug 9505.
http://bugzilla.kernel.org/show_bug.cgi?id=9505
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch fixes the STATUS_RF_KILL_HW state is not cleared problem if the
device goes to suspend when the rf_kill switch is enabled. The bug causes
the driver always thinks the rf_kill switch is enabled (although it is
disabled) after resume.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c: In function `tsf_write_file':
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
We do not know what type was used to implement u64 and we can never use u64 in
printk(), sscanf(), etc.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that libertas selects WIRELESS_EXT, since selecting other stuff that
should depend on WEXT, like IEEE80211, doesn't seem to drag that in for us.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rate control algo reference leak in case if network device has been
failed to register. In this case special flag priv->mac80211_registered is
not set and the rate algo reference is not freeing on module unload. That
leads to OOPs in further ieee80211 rate register/unregister procedure (by
any callee).
It should fix the bug #9470http://bugzilla.kernel.org/show_bug.cgi?id=9470
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah found an alignment problem with zd1211rw driver at
2007-11-19. This patch fixes it, it is based on the patch proposed by
Herbert Xu. The alignment 4 has been the agreed value on the
linux-wireless mailing list.
Notify that the problem does only affect the old zd1211rw softmac
driver and not the zd1211rw-mac80211 driver. Daniel Drake has
already provided a patch for the replacement of the softmac
driver, which this patch will break.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
MAINTAINERS: update the NFS CLIENT entry
NFS: Fix an Oops in NFS unmount
Revert "NFS: Ensure we return zero if applications attempt to write zero bytes"
SUNRPC xprtrdma: fix XDR tail buf marshalling for all ops
NFSv2/v3: Fix a memory leak when using -onolock
NFS: Fix NFS mountpoint crossing...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Re-journal buffers after transaction extend
ocfs2: Allow for debugging of transaction extends
ocfs2: Don't panic when truncating an empty extent
ocfs2: fix exit-while-locked bug in ocfs2_queue_orphans()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
HOWTO: update misspelling and word incorrected
add stable_api_nonsense.txt in korean
HOWTO: change addresses of maintainer and lxr url for Korean HOWTO
Add Documentation for FAIR_USER_SCHED sysfs files
HOWTO: Change man-page maintainer address for Japanese HOWTO
tipar: remove obsolete module
kobject: fix the documentation of how kobject_set_name works
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: revert portions of "UNUSUAL_DEV: Sync up some reported devices from Ubuntu"
usb: Remove broken optimisation in OHCI IRQ handler
USB: at91_udc: correct hanging while disconnecting usb cable
USB: use IRQF_DISABLED for HCD interrupt handlers
USB: fix locking loop by avoiding flush_scheduled_work
usb.h: fix kernel-doc warning
USB: option: Bind to the correct interface of the Huawei E220
USB: cp2101: new device id
usb-storage: Fix devices that cannot handle 32k transfers
USB: sierra: fix product id
Check in sis190_rx_interrupt() is broken on big-endian
(desc->status is little-endian and everything else actually uses
it correctly, including other checks for OWNbit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit ed7e63a51d has tried to fix
section mismatch:
WARNING: vmlinux.o(.init.text+0x17278): Section mismatch: reference to
.exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
But that mismatch still happens.
This patch actually fixing section mismatch by removing __exit from
the header file.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ocfs2_extend_trans() might call journal_restart() which will commit dirty
buffers and then restart the transaction. This means that any buffers which
still need changes should be passed to journal_access() again. Some paths
during extend weren't doing this right.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The nastiest cases of transaction extends are also the rarest. We can expose
them more quickly at the expense of performance by going straight to the
journal_restart() in ocfs2_extend_trans(). Wrap things in OCFS2_DEBUG_FS so
that we only do this when "expensive debugging" is turned on.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
We're holding the cluster lock when a failure might happen in
ocfs2_dir_foreach() so it needs to be released.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct hanging while disconnecting the USB device cable. Prevent a race
between vbus and UDP interrupts. This bug was tracked on at91sam9260ek
boards.
A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock). A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc warning in usb.h:
Warning(linux-2.6.24-rc3-git7//include/linux/usb.h:166): No description found for parameter 'sysfs_files_created'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch to fix the addition of the new product ids I sent.
It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(
Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore PCI expansion ROM P2P prefetch window creation.
This patch reverts previous "Avoid creating P2P prefetch
window for expansion ROMs" change due to regressions that
were spotted on some systems.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So sorry. again My mail is set with EUC-kR.
I'll resend with UTF-8.
Signed-off-by: barrios <minchan.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch to change email address of man-page maintainer for
Japanese HOWTO document (Documentation/ja_JP/HOWTO).
This is for sync to Documentation/HOWTO that Michael Kerrisk mentioned
to me.
From: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access
to Texas Instruments parallel link cable. A user-land method now
exists thru PPDEV & PARPORT.
Signed-off-by: Romain Liévin <roms@lpg.ticalc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] add Nano 7240 driver
[WATCHDOG] ipmi: add the standard watchdog timeout ioctls
[WATCHDOG] IT8212F watchdog driver
[WATCHDOG] Sbus: cpwatchdog, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] bfin_wdt, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] Stop looking for device as soon as one is found
[WATCHDOG] at32ap700x_wdt: add support for boot status and add fix for silicon errata
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix lock flag variable location, bump version number
IB/ehca: Serialize HCA-related hCalls if necessary
IB/ehca: Return correct number of SGEs for SRQ
Add proper support for CLOCK_EVT_MODE_RESUME and in the process fix
CLOCK_EVT_MODE_SHUTDOWN so that only the enable bits are toggled for both.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to ARM7TDMI Technical Reference Manual (ARM DDI 0210C) writing
to the DCC data write register coproc dest registers are 1 and 0, not 0
and 1.
ARM920T TRM (ARM DDI 0151C) agrees on that.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA]: irda parameters warning fixes.
[IRDA]: stir4200 fixes.
[IRDA]: irlmp_unregister_link() needs to free lsaps.
[IRDA]: mcs7780 needs to free allocated rx buffer.
[IRDA]: Race between open and disconnect in irda-usb.
[SCTP]: Flush fragment queue when exiting partial delivery.
[AX25]: Locking dependencies fix in ax25_disconnect().
[IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
[IPV6]: Fix the return value of ipv6_getsockopt
[BRIDGE]: Assign random address.
[IPV4]: Updates to nfsroot documentation
[ATM]: Fix compiler warning noise with FORE200E driver
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
[SYNCPPP]: Endianness and 64bit fixes.
[TIPC]: Fix semaphore handling.
[NETFILTER]: xt_hashlimit should use time_after_eq()
[XFRM]: Display the audited SPI value in host byte order.
[NETFILTER]: ip_tables: fix compat copy race
[NETFILTER]: ctnetlink: set expected bit for related conntracks
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make PS3_SYS_MANAGER default y, not m
[POWERPC] Fix rounding bug in emulation for double float operating
[POWERPC] iSeries: don't printk with HV spinlock held
[POWERPC] 82xx: mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
[POWRPC] CPM2: Eliminate section mismatch warning in cpm2_reset().
[POWERPC] Kill non-existent symbols from ksyms and commproc.h
[POWERPC] Fix typo #ifdef -> #ifndef
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ensure that ST0_FR is never set on a 32 bit kernel
[MIPS] time: Delete weak definition of plat_time_init() due to gcc bug.
[MIPS] PCI: Make pcibios_fixup_device_resources ignore legacy resources.
[MIPS] Atlas, Malta: Don't free firmware memory on free_initmem.
[MIPS] Alchemy: fix off by two error in __fixup_bigphys_addr()
[MIPS] Alchemy: fix PCI resource conflict
[MIPS] time: Set up Cobalt's mips_hpt_frequency
Git commit 3610cce87a (yeah my own :-/)
introduced a bug in regard to pud/pmd table entries.
If the address of the page table refered to by a pud/pmd value happens
to have zeroes in the lower 32 bits, pud_present and pmd_present return
false. The obvious effect is that this triggers the BUG_ON in exit_mmap
because some ptes will not get released on process end. Worse is that
the next fault for memory covered by that pud/pmd will allocate another
pmd/pte table and populate the pud/pmd entry. The old page table
entries hanging below this entry are lost!
The fix is simple, properly check against 0. The check is added for
pud_none/pmd_none as well even if these two functions work because
the invalid bit is in the lower 32 bits.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes:
CHECK /home/kernel/src/net/irda/parameters.c
/home/kernel/src/net/irda/parameters.c:466:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:520:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:573:2: warning: Using plain integer as NULL pointer
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>
The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in irlmp_unregister_link(). Hashbin for lsaps is created in
irlmp_register_link and should probably be freed in irlmp_unregister_link().
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of partial delivery, we may have complete messages
sitting on the fragment queue. These messages are stuck there
until a new fragment arrives. This can comletely stall a
given association. When clearing partial delivery state, flush
any complete messages from the fragment queue and send them on
their way up.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bernard Pidoux reported these lockdep warnings:
[ INFO: possible irq lock inversion dependency detected ]
2.6.23.1 #1
---------------------------------------------------------
fpac/4933 just changed the state of lock:
(slock-AF_AX25){--..}, at: [<d8be3312>] ax25_disconnect+0x46/0xaf
[ax25]
but this lock was taken by another, soft-irq-safe lock in the past:
(ax25_list_lock){-+..}
and interrupts could create inverse lock ordering between them.
[...]
[ INFO: inconsistent lock state ]
2.6.23.1 #1
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
ax25_call/4005 [HC0[0]:SC0[0]:HE1:SE1] takes:
(slock-AF_AX25){-+..}, at: [<d8b79312>] ax25_disconnect+0x46/0xaf [ax25]
[...]
This means slock-AF_AX25 could be taken both from softirq and process
context with softirqs enabled, so it's endangered itself, but also makes
ax25_list_lock vulnerable. It was not 100% verified if the real lockup
can happen, but this fix isn't very costly and looks safe anyway.
(It was tested by Bernard with 2.6.23.9 and 2.6.24-rc5 kernels.)
Reported_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Tested_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_input_metrics() refers to the built-time constant TCP_RTO_MIN
regardless of configured minimum RTO with iproute2.
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NETFILTER if not selected when compile the kernel source code,
ipv6_getsockopt will returen an EINVAL error if optname is not supported by
the kernel. But if CONFIG_NETFILTER is selected, ENOPROTOOPT error will
be return.
This patch fix to always return ENOPROTOOPT error if optname argument of
ipv6_getsockopt is not supported by the kernel.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assigning a valid random address to bridge device solves problems
when bridge device is brought up before adding real device to bridge.
When the first real device is added to the bridge, it's address
will overide the bridges random address.
Note: any device added to a bridge must already have a valid
ethernet address.
br_add_if -> br_fdb_insert -> fdb_insert -> is_valid_ether_addr
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between ip=off and ip=::::::off has been a cause of much
confusion. Document how each behaves, and do not contradict ourselves by
saying that "off" is the default when in fact "any" is the default and is
descibed as being so lower in the file.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc throws these warnings with:
CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set
drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used
By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Damien Thebault, the double POSTROUTING hook invocation
fix caused outgoing packets routed between two bridges to appear without
a link-layer header. The reason for this is that we're skipping the
br_nf_post_routing hook for routed packets now and don't save the
original link layer header, but nevertheless tries to restore it on
output, causing corruption.
The root cause for this is that skb->nf_bridge has no clearly defined
lifetime and is used to indicate all kind of things, but that is
quite complicated to fix. For now simply don't touch these packets
and handle them like packets from any other device.
Tested-by: Damien Thebault <damien.thebault@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* trivial annotations
* long != 32bit, use __be32
* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Kevin, tipc's release() does down_interruptible() and
ignores the return value. So if signal_pending() we'll end up doing
up() on a non-downed semaphore. Fix.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid jiffies wraparound and its effect, special care must
be taken
when doing comparisons ...
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IPsec protocol SPI values are written to the audit log in
network byte order which is different from almost all other values which
are recorded in host byte order. This patch corrects this inconsistency
by writing the SPI values to the audit record in host byte order.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying entries to user, the kernel makes two passes through the
data, first copying all the entries, then fixing up names and counters.
On the second pass it copies the kernel and match data from userspace
to the kernel again to find the corresponding structures, expecting
that kernel pointers contained in the data are still valid.
This is obviously broken, fix by avoiding the second pass completely
and fixing names and counters while dumping the ruleset, using the
kernel-internal data structures.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a fix. It sets IPS_EXPECTED for related conntracks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code used by the non-__devinit s2io_open() mustn't be __devinit.
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x6f6e3e): Section mismatch: reference to .init.text.20:s2io_test_intr (between 's2io_open' and 's2io_ethtool_sset')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.init.text.20+0x4cb25): Section mismatch: reference to .exit.text:sis190_mii_remove (between 'sis190_init_one' and 'read_eeprom')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Frank Rowand <frank.rowand@am.sony.com> reports:
> In linux-2.6.24-rc4 the Toshiba RBTX4927 hangs on boot.
>
> The cause is that plat_time_init() from arch/mips/tx4927/common/
> tx4927_setup.c does not override the __weak plat_time_init() from
> arch/mips/kernel/time.c. This is due to a compiler bug in gcc 4.1.1. The
> bug is reported to not exist in earlier versions of gcc, and to be fixed in
> 4.1.2. The problem is that the __weak plat_time_init() is empty and thus
> gets optimized out of existence (thus the linker is never given the option
> to replace the __weak function).
[ He meant the call to plat_time_init() from time_init() gets optimized away ]
> For more info on the gcc bug see
>
> http://gcc.gnu.org/bugzilla/show_bug.cgi?id=27781
>
> The attached patch is one workaround. Another possible workaround
[ His patch adds -fno-unit-at-a-time for time.c ]
> would be to change the __weak plat_time_init() to be a non-empty
> function.
The __weak definition of plat_time_init was only ever meant to be a
migration helper to keep platforms that don't have a plat_time_init
compiling. A few greps says that all platforms now supply their own
plat_time_init() so the weak definition is no longer needed. So I
instead delete it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There might be other reasons why a resource might be marked as fixed
such as a PCI UART holding the system console but until we use
IORESOURCE_PCI_FIXED that way also this will work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the PCI specific code in this function doesn't check for the address range
being under the upper bound of the PCI memory window correctly -- fix this,
somewhat beautifying the code around the check, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
... by getting the PCI resources back into the 32-bit range -- there's no
need therefore for CONFIG_RESOURCES_64BIT either. This makes Alchemy PCI
work again while currently the kernel skips the bus scan.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
This patch fixes this issue.
Signed-off-by: Liu Yu <b13201@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Starting in 2.6.23...
Several reports from X60 users complained that the default Lenovo keymap
issuing EV_KEY KEY_BRIGHTNESS_UP/DOWN input events caused major issues when
the proper brightness support through ACPI video.c was loaded.
Therefore, remove the generation of these events by default, which is the
right thing for T60, X60, R60, T61, X61 and R61 with their latest BIOSes.
Distros that want to misuse these events into OSD reporting (which requires
an ugly hack from hell in HAL) are welcome to set up the key map they need
through HAL. That way, we don't break everyone else's systems.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
for sn2_defconfig:
WARNING: vmlinux.o(.text+0x4b8601): Section mismatch: reference to .init.data:node_to_pxm_map (between '__acpi_map_pxm_to_node' and 'acpi_get_pxm')
WARNING: vmlinux.o(.text+0x4b8741): Section mismatch: reference to .init.data:pxm_to_node_map (between 'acpi_map_pxm_to_node' and 'acpi_get_node')
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ->cap fields of struct acpi_video_device and struct acpi_video_bus
are 1B each, not 4B. The oversized memset()'s corrupted the subsequent
list_head fields. This resulted in silent corruption without
CONFIG_DEBUG_LIST and BUG's with it. This patch uses sizeof() to pass
the proper bounds to the memset() calls and thereby correct the bugs.
Signed-off-by: William Irwin <wli@holomorphy.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Len Brown <len.brown@intel.com>
QAM SNR values were incorrect when the cable was disconnected. This
patch extends the lookup tables to ensure correct values are being
returned.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since not all code under drivers/media/video/ depends on
CONFIG_VIDEO_DEV we cannot only enter it depending
on CONFIG_VIDEO_DEV.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commit:
18c32dac75 "kbuild: fix
building with O=.. options"
disabled the creation of a Makefile in a new O=... directory. Restore it.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This was caught and identified by Greg Onufer.
Since we setup the 256M/4M bitmap table after taking over the trap
table, it's possible for some 4M mapping to get loaded in the TLB
beforhand which later will be 256M mappings.
This can cause illegal TLB multiple-match conditions. Fix this by
setting up the bitmap before we take over the trap table.
Next, __flush_tlb_all() was not doing anything on hypervisor
platforms. Fix by adding sun4v_mmu_demap_all() and calling it.
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 19fb145799 the callers in
videobuf-core.c that already hold the lock must call
__videobuf_read_start() instead of videobuf_read_start().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add in the new NFS mailing list on vger, website, and git tree info, and
update my email address to reflect the fact that I've been working for
netapp for the past 2 years.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
set_io_32bit() (ide_procset_t function) can race against running
PIO transfers. Fix it by using ide_spin_wait_hwgroup().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After looking into the HPT370 manual (now that I have it) and re-checking all
the timing tables, here's what I have discovered:
- at 33 MHz clock, PIO mode 0 timings turned to be overclocked, and all other
PIO modes underclocked;
- at 50 MHz clock, PIO modes 0 to 2 turned to be overclocked;
- at 66 MHz clock, PIO mode 0 was overclocked too.
Finally, the taskfile timing (matching PIO mode 0) turned to be overclocked at
all clock frequencies (and in all manuals)...
The new timings have been tested on HPT370 chip (at 33 MHz PCI clock) and on
HPT371N chip (at both 50 and 66 MHz DPLL clock).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In case of Promise TX4 the first PCI device is located at slot 1
and the second one is at slot 2 so the offset used by pci_get_slot()
should be "+1" and not "+2".
Thanks goes out to Markus Dietz for bugreport and testing this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
post_transform_command() call in cdrom_newpc_intr() has no effect because
it is done after the request has already been fully completed (rq->bio and
rq->data are always NULL). It was verified to be true regardless whether
INQUIRY command is using DMA or PIO to transfer data (by using modified
Tejun Heo's test-shortsg.c utility and adding a few printk()-s to ide-cd).
This was uncovered thanks to the "blk_end_request: full I/O completion
handler (take 3)" patch series from Kiyoshi Ueda.
Cc: jens.axboe@oracle.com
Cc: bharrosh@panasas.com
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_xfer_verbose() fixups:
- beautify returned mode names
- fix PIO5 reporting
- make it return 'const char *'
* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().
* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
DMA info in identify block.
* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().
As a result DMA won't be tuned or will be disabled after tuning if device
reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
same checks while the IDE device is probed by ide-{cd,disk} device driver).
* Remove no longer needed ide_dma_verbose().
This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
skipping word 93 validity check
, UDMA(66)
and later debugged by Mark Lord to be caused by:
ide_dma_verbose()
printk( ... "2048kB Cache");
eighty_ninty_three()
printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
ide_dma_verbose()
printk(", UDMA(66)"
Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.
v2:
* fixes suggested by Randy:
- use KERN_CONT for printk()-s in ide-{cd,disk}.c
- don't remove argument name from ide_xfer_verbose() declaration
v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
(spotted by Sergei).
* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).
* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
limited by 'req_mode').
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove trailing whitespaces
* 'if()' -> 'if ()'
* remove extra new-line before EXPORT_SYMBOL_GPL()
* add extra new-line after 'id' definition
* respect 80-columns limit
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add missing checks for control register existence (some legacy m68k specific
IDE controllers don't have it). Also use drive->ctl while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several pSeries firmware versions share a rare locking issue in the
HCA-related hCalls. Check for a feature flag that indicates the issue
being fixed and serialize all HCA hCalls if not.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware would round up the number of SGEs to four, because the WQE
structure holds four SGEs. For SRQ, only three are supported, so return
a fixed value instead.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This field and corresponding defines are simply never used anywhere
in the code. But its mere presence is enough to confuse some host
driver authors who attempt to rely on it. Let's eliminate the
possibility for confusion and remove it entirely.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The JMicron JMB38x chip doesn't support transfers that aren't 32-bit
aligned (both size and start address). It also doesn't like switching
between PIO and DMA mode, so it needs to be reset after each request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ensure that the dummy 'root dentry' is invisible to d_find_alias(). If not,
then it may be spliced into the tree if a parent directory from the same
filesystem gets mounted at a later time.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This reverts commit b9148c6b80.
On Wed, 12 Dec 2007 10:57:30 -0500, Chuck Lever wrote
> commit b9148c6b should be reverted. It was recently forward-ported
> from some years-old patches, and is clearly not needed now.
>
> On Dec 11, 2007, at 5:21 PM, Adrian Bunk wrote:
>
>> This code became dead after commit
>> b9148c6b80
>> (which BTW doesn't seem to have changed any behaviour) and can
>> therefore
>> be removed.
>>
>> Spotted by the Coverity checker.
>>
>> Signed-off-by: Adrian Bunk <bunk@kernel.org>
>>
>> ---
>> --- linux-2.6/fs/nfs/direct.c.old 2007-12-02 21:54:53.000000000 +0100
>> +++ linux-2.6/fs/nfs/direct.c 2007-12-02 21:55:10.000000000 +0100
>> @@ -897,15 +897,12 @@ ssize_t nfs_file_direct_write(struct kio
>> if (!count)
>> goto out; /* return 0 */
>>
>> retval = -EINVAL;
>> if ((ssize_t) count < 0)
>> goto out;
>> - retval = 0;
>> - if (!count)
>> - goto out;
>>
>> retval = nfs_sync_mapping(mapping);
>> if (retval)
>> goto out;
>>
>> retval = nfs_direct_write(iocb, iov, nr_segs, pos, count);
>>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.
This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 70eba18b56, as per
Jeff Garzik:
"That was meant for 2.6.25, and actually (due to patching) applied to
a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rpcrdma_convert_iovs is passed an xdr_buf representing either an RPC
request or an RPC reply. In the case of a request, several
calculations and tests involving pos are unnecessary. In the case of a
reply, several calculations and tests involving pos are incorrect (the
code tests pos against the reply xdr buf's len field, which is always
0 at the time rpcrdma_convert_iovs is executed). This change removes
the incorrect/unnecessary calculations and tests involving pos.
This fixes an observed problem when reading certain file sizes over
NFS/RDMA.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: James Lentini <jlentini@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Neil Brown said:
> Hi Trond,
>
> We found that a machine which made moderately heavy use of
> 'automount' was leaking some nfs data structures - particularly the
> 4K allocated by rpc_alloc_iostats.
> It turns out that this only happens with filesystems with -onolock
> set.
> The problem is that if NFS_MOUNT_NONLM is set, nfs_start_lockd doesn't
> set server->destroy, so when the filesystem is unmounted, the
> ->client_acl is not shutdown, and so several resources are still
> held. Multiple mount/umount cycles will slowly eat away memory
> several pages at a time.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: NeilBrown <neilb@suse.de>
The check that was added to nfs_xdev_get_sb() to work around broken
servers, works fine for NFSv2, but causes mountpoint crossing on NFSv3 to
always return ESTALE.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
On Tue, 4 Dec 2007, Ingo Molnar wrote:
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_get_tuner_i2c_master'
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_set_config'
Seems like -common part contains also code that is not completely
common to all the modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch
drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is pretty serious bug. map->count is never initialized after the
call to kmalloc making the count start at some random trash value. The
end result is leaking videobufs.
Also, fix up the debug statements to print unsigned values.
Pushed to http://ifup.org/hg/v4l-dvb too
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Complement va_start() with va_end() + minor style fixes in the same function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result. Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case
TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a modified version of a patch previously posted by Thomas
Unverzagt.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch is required so that the autodetecion code also works after
a reboot.
Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If we get an error during the actual policy lookup we don't free the
original dst while the caller expects us to always free the original
dst in case of error.
This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan module cleanup function starts with
vlan_netlink_fini();
vlan_ioctl_set(NULL);
The first call removes all the vlan devices and
the second one closes the vlan ioctl.
AFAIS there's a tiny race window between these two
calls - after rtnl unregistered all the vlans, but
the ioctl handler isn't set to NULL yet, user can
manage to call this ioctl and create one vlan device,
and that this function will later BUG_ON seeing
non-emply hashes.
I think, that we must first close the vlan ioctl
and only after this remove all the vlans with the
vlan_netlink_fini() call.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some return value comments for void functions.
Fixed it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. netif_rx_ni calls netif_rx, so the same problem occurs in
the files below.
I have left the updating of dev->last_rx after the calls to netif_rx_ni
because it seems time dependent, but moved the other field updates before.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Herbert, the ipv4_devconf_setall should be called
only when the ifa is added to the device. However, failed
ifa allocation may bring things into inconsistent state.
Move the call to ipv4_devconf_setall after the ifa allocation.
Fits both net-2.6 (with offsets) and net-2.6.25 (cleanly).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTCF_xxx flags, defined in include/linux/in_route.h) are available for
IPv4 route (rtable) entries only. Use RTF_xxx flags instead, defined
in include/linux/ipv6_route.h, for IPv6 route entries (rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some versions of Xen 3.x set their magic number to "xen-3.[12]", so
relax the test to match them.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ultimately to implement /proc perfectly we need an implementation of
d_revalidate because files and directories can be removed behind the back
of the VFS, and d_revalidate is the only way we can let the VFS know that
this has happened.
Unfortunately the linux VFS can not cope with anything in the path to a
mount point going away. So a proper d_revalidate method that calls d_drop
also needs to call have_submounts which is moderately expensive, so you
really don't want a d_revalidate method that unconditionally calls it, but
instead only calls it when the backing object has really gone away.
proc generic entries only disappear on module_unload (when not counting the
fledgling network namespace) so it is quite rare that we actually encounter
that case and has not actually caused us real world trouble yet.
So until we get a proper test for keeping dentries in the dcache fix the
current d_revalidate method by completely removing it. This returns us to
the current status quo.
So with CONFIG_NETNS=n things should look as they have always looked.
For CONFIG_NETNS=y things work most of the time but there are a few rare
corner cases that don't behave properly. As the network namespace is
barely present in 2.6.24 this should not be a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "Denis V. Lunev" <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a wifi module connected to the spi bus and got sometimes FIFO
overrun errors on the spi bus.
After some investigation i found that the driver loads the TCR (transmit
count) register before the RCR (receive count). When the transfer list is
not empty the atmel_spi_next_message is called while tx and rx are enabled.
As soon as the TCR is loaded, hardware starts transfer and causes a rx
fifo overrun because the RCR is not loaded yet.
Load the RCR before the TCR. After this patch the fifo overrun disapears
at out setup.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The esp_reset_cleanup() function is called with the host lock held and
invokes starget_for_each_device() which wants to take it too. Here is a
fix along the lines of shost_for_each_device()/__shost_for_each_device()
adding a __starget_for_each_device() counterpart which assumes the lock
has already been taken.
Eventually, I think the driver should get modified so that more work is
done as a softirq rather than in the interrupt context, but for now it
fixes a bug that causes the spinlock debugger to fire.
While at it, it fixes a small number of cosmetic problems with
starget_for_each_device() too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There should be an of_node_put when breaking out of a loop that iterates
using for_each_compatible_node.
This was detected and fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_compatible_node;
@@
T *d;
...
for_each_compatible_node(d,...)
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The follow_hugetlb_page() fix I posted (merged as git commit
5b23dbe817) missed one case. If the pte is
present, but not writable and write access is requested by the caller to
get_user_pages(), the code will do the wrong thing. Rather than calling
hugetlb_fault to make the pte writable, it notes the presence of the pte
and continues.
This simple one-liner makes sure we also fault on the pte for this case.
Please apply.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Acked-by: Dave Kleikamp <shaggy@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some places where CLOCK_TICK_RATE may be used incorrectly:
arch/arm/mach-mx3/time.c:125: __raw_writel((v / CLOCK_TICK_RATE) - 1, MXC_GPT_GPTPR);
drivers/watchdog/davinci_wdt.c:103: timer_margin = (((u64)heartbeat * CLOCK_TICK_RATE) & 0xffffffff);
drivers/watchdog/davinci_wdt.c:105: timer_margin = (((u64)heartbeat * CLOCK_TICK_RATE) >> 32);
drivers/watchdog/ks8695_wdt.c:64: unsigned long tval = wdt_time * CLOCK_TICK_RATE;
I'm not sure whether this definition is used there, but adding parentheses
should be good anyway.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc comments in drivers/pcmcia/:
- ti113x.h does not contain kernel-doc, so don't use /** to begin a doc
comment
- yenta_socket.c: remove /** on non-kernel-doc comments;
escape the ':' in an "http:" comment so that it won't be treated as a
section heading;
- cs.c: remove /** on non-kernel-doc comments & add function parameter info
- ds.c: fix function parameter info
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Third rendition of FireWire OHCI 1.0 Isochronous Receive support, using a
zer-copy method similar to OHCI 1.1 which puts the IR data payload directly
into the userspace buffer. The zero-copy implementation eliminates the
video artifacts, audio popping, and buffer underrun problems seen with
version 1 of this patch, as well as fixing a regression in OHCI 1.1 support
introduced by version 2 of this patch.
Successfully tested in OHCI 1.1 mode on the following chipsets:
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
- Ti TSB41AB2 (rev 01), OHCI 1.1 (PCI on SB Audigy)
- Apple UniNorth 2 (rev 81), OHCI 1.1 (PowerBook G4 onboard)
Successfully tested in OHCI 1.0 mode on the following chipsets:
- Agere FW323 (rev 06), OHCI 1.0 (Mac Mini onboard)
- Agere FW323 (rev 06), OHCI 1.0 (PCI)
- Via VT6306 (rev 46), OHCI 1.0 (PCI)
- NEC OrangeLink (rev 01), OHCI 1.0 (PCI)
- NEC uPD72847 (rev 01), OHCI 1.1 (PCI)
- Ti XIO2200(A) (rev 01), OHCI 1.1 (PCIe)
The bulk of testing was done in an x86_64 system, but was also successfully
sanity-tested on other systems, including a PPC(32) PowerBook G4 and an i686
EPIA M10k. Crude benchmarking (watching top during capture) puts the cpu
utilization during capture on the EPIA's 1GHz Via C3 processor around 13%,
which is down from 30% with the v1 code.
Some implementation details:
To maintain the same userspace API as dual-buffer mode, we set up two
descriptors for every incoming packet. The first is an INPUT_MORE descriptor,
pointing to a buffer large enough to hold just the packet's iso headers,
immediately followed by an INPUT_LAST descriptor, pointing to a chunk of the
userspace buffer big enough for the packet's data payload. With this setup,
each incoming packet fills in these two descriptors in a manner that very
closely emulates dual-buffer receive, to the point where the bulk of the
handle_ir_* code is now identical between the two (and probably primed for
some restructuring to share code between them).
The only caveat I have at the moment is that neither of my OHCI 1.0 Via
VT6307-based FireWire controllers work particularly well with this code
for reasons I have yet to figure out.
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix xfs_ichgtime()s broken usage of I_SYNC
[XFS] Make xfsbufd threads freezable
[XFS] revert to double-buffering readdir
[XFS] Fix broken inode cluster setup.
[XFS] Clear XBF_READ_AHEAD flag on I/O completion.
[XFS] Fixed a few bugs in xfs_buf_associate_memory()
[XFS] 971064 Various fixups for xfs_bulkstat().
[XFS] Fix dbflush panic in xfs_qm_sync.
This reverts commit fd6e732186, which
helped up things on MIPS, but was wrong for everything else. As Ralf
Baechle puts it:
"It seems the whole MIPS resource managment is complicated enough (out
of necessity) that only a few people actually grok it. Ioports being
actually memory mapped on MIPS only makes the confusion worse, sigh."
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PowerMac and CHRP/BriQ platforms have quirks to switch some IDE
controllers from legacy mode to fully native mode. Those quirks
however will not work properly anymore due to a change to the
generic code to better handle legacy IDE resources.
This fixes it by moving those quirk to "early" quirks (so they
run before resources are probed for the devices) and clearing
all BARs after the conversion to force a reallocation of sane
values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent I_LOCK->I_SYNC changes mistakenly changed xfs_ichgtime to look
at I_SYNC instead of I_LOCK. This was incorrect and prevents newly created
inodes from moving to the dirty list. Change this to the correct check
which is for I_NEW, not I_LOCK or I_SYNC so that behaviour is correct.
SGI-PV: 974225
SGI-Modid: xfs-linux-melb:xfs-kern:30204a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Fix breakage caused by commit 8314418629
that did not introduce the necessary call to set_freezable() in
xfs/linux-2.6/xfs_buf.c .
SGI-PV: 974224
SGI-Modid: xfs-linux-melb:xfs-kern:30203a
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The current readdir implementation deadlocks on a btree buffers locks
because nfsd calls back into ->lookup from the filldir callback. The only
short-term fix for this is to revert to the old inefficient
double-buffering scheme.
SGI-PV: 973377
SGI-Modid: xfs-linux-melb:xfs-kern:30201a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
The radix tree based inode caches did away with the inode cluster hashes,
replacing them with a bunch of masking and gang lookups on the radix tree.
This masking got broken when moving the code to per-ag radix trees and
indexing by agino # rather than straight inode number. The result is
clustered inode writeback does not cluster and things can go extremely
slowly when there are lots of inodes to write.
Fix it up by comparing the agino # of the inode we just looked up to the
index of the cluster we are looking for.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
SGI-PV: 972915
SGI-Modid: xfs-linux-melb:xfs-kern:30033a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
- calculation of 'page_count' was incorrect as it did not
consider the offset of 'mem' into the first page. The
logic to bump 'page_count' didn't work if 'len' was <=
PAGE_CACHE_SIZE (ie offset = 3k, len = 2k).
- setting b_buffer_length to 'len' is incorrect if 'offset'
is > 0. Set it to the total length of the buffer.
- I suspect that passing a non-aligned address into
mem_to_page() for the first page may have been causing
issues - don't know but just tidy up that code anyway.
SGI-PV: 971596
SGI-Modid: xfs-linux-melb:xfs-kern:30143a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
- sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]()
- remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This
special case causes bulkstat to fail because the special case uses
xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions
have different semantics. xfs_bulkstat() will return the next inode
after the one supplied while skipping internal inodes (ie quota inodes).
xfs_bulkstate_single() will only lookup the inode supplied and return
an error if it is an internal inode.
- in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied
so in cases were we return without examining any inodes the scan wont
restart back at zero.
- sanity check for valid *ubcountp values. Cannot sanity check for valid
ubuffer here because some users of xfs_bulkstat() don't supply a buffer.
- checks against 'ubleft' (the space left in the user's buffer) should be
against 'statstruct_size' which is the supplied minimum object size.
The mixture of checks against statstruct_size and 0 was one of the
reasons we were skipping inodes.
- if the formatter function returns BULKSTAT_RV_NOTHING and an error and
the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT
is for inodes that are no longer valid and we just skip them. EINVAL is
returned if we try to lookup an internal inode so we skip them too. For
a DMF scan if the inode and DMF attribute cannot fit into the space left
in the user's buffer it would return ERANGE. We didn't handle this error
and skipped the inode. We would continue to skip inodes until one fitted
into the user's buffer or we completed the scan.
- put back the recalculation of agino (that got removed with the last fix)
at the end of the while loop. This is because the code at the start of
the loop expects agino to be the last inode examined if it is non-zero.
- if we found some inodes but then encountered an error, return success
this time and the error next time. If the formatter aborted with ENOMEM
we will now return this error but only if we couldn't read any inodes.
Previously if we encountered ENOMEM without reading any inodes we
returned a zero count and no error which falsely indicated the scan was
complete.
SGI-PV: 973431
SGI-Modid: xfs-linux-melb:xfs-kern:30089a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
The recent behaviour layer removal dropped the check for quotas that have
been requested at mount time but have subsequently been turned off. This
results in a panic when accessing m_quotainfo which has been freed.
This patch adds the check originally made by xfs_qm_syncall() to
xfs_qm_sync().
SGI-PV: 969769
SGI-Modid: xfs-linux-melb:xfs-kern:29908a
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Both slob and slub react to __GFP_ZERO by clearing the allocation, which
means that passing the GFP_ZERO bit down to the page allocator is just
wasteful and pointless.
Acked-by: Matt Mackall <mpm@selenic.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check introduced in commit:
4f1127e204 "kbuild: fix
infinite make recursion"
caused certain external modules not to build and
also caused 'make targz-pkg' to fail.
This is a minimal fix so we revert to previous
behaviour - but we do not overwrite the Makefile
in the top-level directory.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Jan Altenberg <jan.altenberg@linutronix.de> reported that
building with redirected input like this failed:
make O=dir oldconfig bzImage < /dev/null
The problem were caused by a make silentoldconfig being
run before oldconfig and with a non-recent .config the build
failed because silentoldconfig requires non-redirected stdin.
Silentoldconfig was run as a side-effect of having the
top-level Makefile re-made by make.
Introducing an empty rule for the top-level Makefile
(and Kbuild.include) fixed the issue.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Most Malta use an FPGA CPU card which rarely is good for more than 40MHz.
So the performance penalta of the regular timer interrupt, especially
for the VSMP kernel model is significant, even at a mere 100Hz.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IP7 will be enabled automatically in mips_clockevent_init(), if available.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the introduction of MIPS_CPU_IRQ_BASE, the hardcoded IRQ number of
the au1100/au1200 SD controller(s) is no longer valid.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix CKEN register corruption in the PXA27x cold reset code
located in sound/arm/pxa27x-ac97.c. The problem has been
introduced with a pxa_set_cken() function change in linux 2.6.23.
This patch is based on patch 4527/1 that fixes the same problem in
the ASoC PXA-AC97 driver. Additionally a definition for the CKEN
index value is added and applied to both PXA AC97 drivers.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change printk to dev_dbg in ITE 8152 driver and remove printk in ITE 8152 ISR.
Move PCI intialization from ->scan to ->preinit method
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If "CPEI Processor Override" bit is not set in "Platform Interrupt
Source Flags" in "Platform Interrupt Sources Structure" in ACPI MADT,
the target processor of CPEI is restricted to a specific CPU. Because
of this, the delivery mode for CPEI should be IOSAPIC_FIXED.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
'!' has a higher priority than '&', so as was
this won't test the first bit, but rather evaluates to false for any non-zero
lsapic->lapic_flags.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rename _bss to __bss_start as on other architectures. That makes it
possible to use the <linux/sections.h> instead of own declarations. Also
add __bss_stop because that symbol exists on other architectures.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When initializing pci_controller->node to point to the closest node we need
to take into consideration that a PIC PCI Bridge ASIC can be connected to a
headless/memless node just like the TIOCP and TIOCE Bridge ASICs
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make some IOSAPIC functions static and remove one that is unused.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not all the return value of __copy_from_user and
__put_user is checked.This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the unionfs patch applied I get
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
the other architectures (some, at least) export copy_page() so I guess ia64
should also do so.
To do this we need to move the copy_page() functions out of lib.a and into
built-in.o and add the EXPORT_SYMBOL().
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Don't assume that this file has execute permissions. For example, patch(1)
loses that information.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/ia64-unknown-linux-gnu/lib/gcc/ia64-unknown-linux-gnu/3.4.5/../../../../ia64-unknown-linux-gnu/bin/ld: section .data.patch [a000000000000500 -> a000000000000507] overlaps section .dynamic [a0000000000003c8 -> a000000000000507]
This only appears to be a problem with strangely configured
cross-compilation ... native compilers don't have this issue.
But in the interests of helping others at least compile for
ia64, this can go in. -Tony
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Spurious NCQ completion detection implemented in ahci was incorrect.
On AHCI receving and processing FISes and raising interrupts are not
interlocked and spurious interrupts are expected.
For example, if an interrupt occurs while interrupt handler is running
and the running interrupt handler handles the event the new IRQ
indicated, after IRQ handler finishes, it will be executed again
because IRQ pending bit is set by the new interrupt but there won't be
anything to process.
Please read the following message for more information.
http://article.gmane.org/gmane.linux.ide/26012
This patch...
* Removes all spurious IRQ whining from ahci. Spurious NCQ completion
detection was completely wrong. Spurious D2H Register FIS taught us
that some early drives send spurious D2H Register FIS with I bit set
while NCQ commands are in progress but none of recent drives does
that and even the ones which show such behavior can do NCQ fine.
* Kills all NCQ blacklist entries which were added because of spurious
NCQ completions. I tracked down each commit and verified all
removed ones are actually added because of spurious completions.
WD740ADFD-00NLR1 wasn't deleted but moved upward because the drive
not only had spurious NCQ completions but also is slow on sequential
data transfers if NCQ is enabled.
Maxtor 7V300F0 was added by 0e3dbc01d5
from Alan Cox. I can only find evidences that the drive only had
troubles with spuruious completions by searching the mailing list.
This entry needs to be verified and removed if it doesn't have other
NCQ related problems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ICH6 R/Ms share PCI ID between piix and ahci modes and we've been
allowing ahci to attach regardless of how BIOS configured it.
However, enabling AHCI mode when the controller is in combined mode
can result in unexpected behavior. Don't attach if the controller is
in combined mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bill Nottingham <notting@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Toshiba Tecra M4 to broken suspend list. This is from OSDL
bugzilla bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There isn't much point in reporting -EOPNOTSUPP as failure. Also the
message was missing newline.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Making sure register initialisation is complete before proceeding further.
The driver must wait until initialization is complete before attempting to
access any other device registers.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This updates the copyright notices of the new EMAC driver to
avoid confusion as who is to be blamed for new bugs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch moves dev_set_drvdata(&ofdev->dev, dev) up before tah_reset(ofdev)
is called to avoid a NULL pointer dereference, since tah_reset uses drvdata.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a typo in ibm_newemac/core.c
(tah_port should be used instead of tah_ph)
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The EMAC4_MR1_OBCI(freq) macro expects freg in MHz,
while opb_bus_freq is kept in Hz. Correct this.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how the 44x processors are wired, some EMAC cells
might not be useable (and not connected to a PHY). However, some
device-trees may choose to still expose them (since their registers
are present in the MMIO space) but with an "unused" property in them.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With some PHYs, when the link goes away, the EMAC reset fails due
to the loss of the RX clock I believe.
The old EMAC driver worked around that using some internal chip-specific
clock force bits that are different on various 44x implementations.
This is an attempt at doing it differently, by avoiding the reset when
there is no link, but forcing loopback mode instead. It seems to work
on my Taishan 440GX based board so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When using ZMII for MDIO only (such as 440GX with RGMII for data and ZMII for
MDIO), the ZMII code would fail to properly refcount, thus triggering a
BUG_ON().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the Agere ET1011c PHY as found on the AMCC Taishan
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds BCM5248 and Marvell 88E1111 PHY support to NEW EMAC driver.
These PHY chips are used on PowerPC 440EPx boards.
The PHY code is based on the previous work by Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bnx2x module depends on the zlib_inflate functions. The
build will fail if ZLIB_INFLATE has not been selected manually
or by building another module that automatically selects it.
Modify BNX2X config option to 'select ZLIB_INFLATE' like BNX2
and others. This seems to fix it.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes a race condition in module unload. Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().
Update version to 3.2.3.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add new hash for balance-xor and 802.3ad modes. Originally
submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
Jay Vosburgh to move setting of hash policy out of line, tweak the
documentation update and add version update to 3.2.2.
Glenn's original comment follows:
Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information. This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy. This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.
Signed-off-by: "Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: David Sterba <dsterba@suse.cz>
Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.
Signed-off-by: David Sterba <dsterba@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
Code for rendering multivalue sysfs files occurs three times
in this module. Rename 'buffer' to 'buf' in the first, for
the sake of consistency.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'. This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.
I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
Also remove trailing spaces from multivalued files.
This fixes output like for example:
$ od -c /sys/class/net/bond0/bonding/slaves
0000000 e t h - l e f t e t h - r i g
0000020 h t \n \0
0000025
It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires. The three multivalue
cases are different, because they also have to swallow back a trailing
space.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
ACPI: move timer broadcast before busmaster disable
clockevents: warn once when program_event() is called with negative expiry
hrtimers: avoid overflow for large relative timeouts
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: enable early use of sched_clock()
lockdep: make cli/sti annotation warnings clearer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Fix wrong pt_regs in critical exception handler
[AVR32] Fix copy_to_user_page() breakage
[AVR32] Follow the rules when dealing with the OCD system
[AVR32] Clean up OCD register usage
[AVR32] Implement irqflags trace and lockdep support
[AVR32] Implement stacktrace support
[AVR32] Kconfig: Use def_bool instead of bool + default
[AVR32] Fix invalid status register bit definitions in asm/ptrace.h
[AVR32] Add TIF_RESTORE_SIGMASK to the work masks
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[AF_RXRPC]: Add a missing goto
[VLAN]: Lost rtnl_unlock() in vlan_ioctl()
[SCTP]: Fix the bind_addr info during migration.
[SCTP]: Add bind hash locking to the migrate code
[IPV4]: Remove prototype of ip_rt_advice
[IPv4]: Reply net unreachable ICMP message
[IPv6] SNMP: Increment OutNoRoutes when connecting to unreachable network
[BRIDGE]: Section fix.
[NIU]: Fix link LED handling.
The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.
In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
The hrtimer problem with large relative timeouts resulting in a
negative expiry time went unnoticed as there is no check in the
clockevents_program_event() code. Put a check there with a WARN_ONCE
to avoid such problems in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Relative hrtimers with a large timeout value might end up as negative
timer values, when the current time is added in hrtimer_start().
This in turn is causing the clockevents_set_next() function to set an
huge timeout and sleep for quite a long time when we have a clock
source which is capable of long sleeps like HPET. With PIT this almost
goes unnoticed as the maximum delta is ~27ms. The non-hrt/nohz code
sorts this out in the next timer interrupt, so we never noticed that
problem which has been there since the first day of hrtimers.
This bug became more apparent in 2.6.24 which activates HPET on more
hardware.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
some platforms have sched_clock() implementations that cannot be called
very early during wakeup. If it's called it might hang or crash in hard
to debug ways. So only call update_rq_clock() [which calls sched_clock()]
if sched_init() has already been called. (rq->idle is NULL before the
scheduler is initialized.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
make cli/sti annotation warnings easier to interpret.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
It's not like it really matters at this point since the system is
dying anyway, but handle_critical pushes too few registers on the
stack so the register dump, which makes the register dump look a bit
strange. This patch fixes it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current implementation of copy_to_user_page() gives "vaddr" to the
cache instruction when trying to sync the icache with the dcache. If
vaddr does not exist in the TLB, the CPU will silently abort the
operation, which may result in the caches staying out of sync.
To fix this, pass the "dst" parameter to flush_icache_range() instead
-- we know this is valid because we just wrote to it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current debug trap handling code does a number of things that are
illegal according to the AVR32 Architecture manual. Most importantly,
it may try to schedule from Debug Mode, thus clearing the D bit, which
can lead to "undefined behaviour".
It seems like this works in most cases, but several people have
observed somewhat unstable behaviour when debugging programs,
including soft lockups. So there's definitely something which is not
right with the existing code.
The new code will never schedule from Debug mode, it will always exit
Debug mode with a "retd" instruction, and if something not running in
Debug mode needs to do something debug-related (like doing a single
step), it will enter debug mode through a "breakpoint" instruction.
The monitor code will then return directly to user space, bypassing
its own saved registers if necessary (since we don't actually care
about the trapped context, only the one that came before.)
This adds three instructions to the common exception handling code,
including one branch. It does not touch super-hot paths like the TLB
miss handler.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Generate a new set of OCD register definitions in asm/ocd.h and rename
__mfdr() and __mtdr() to ocd_read() and ocd_write() respectively.
The bitfield definitions are a lot more complete now, and they are
entirely based on bit numbers, not masks. This is because OCD
registers are frequently accessed from assembly code, where bit
numbers are a lot more useful (can be fed directly to sbr, bfins,
etc.)
Bitfields that consist of more than one bit have two definitions:
_START, which indicates the number of the first bit, and _SIZE, which
indicates the number of bits. These directly correspond to the
parameters taken by the bfextu, bfexts and bfins instructions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The 'H' bit is bit 29, while the 'R' bit doesn't exist. Luckily, we
don't actually use any of the bits in question.
Also update show_regs() to show the Debug Mask and Debug state bits.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
We really need to check TIF_RESTORE_SIGMASK before returning to
userspace. The existing code does not necessarily do this.
Define the work masks as a bitwise OR of the respective flags instead
of a hardcoded hex value to make it easier to spot errors like this in
the future.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add a missing goto to error handling in the RXKAD security module for
AF_RXRPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_cpu() always returns zero on non-SMP builds, but we
really want the physical cpu number in this code in order
to do the right thing.
Based upon a non-SMP kernel boot failure report from Bernd Zeimetz.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_VLAN_NAME_TYPE_CMD command w/o CAP_NET_ADMIN capability
doesn't release the rtnl lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During accept/migrate the code attempts to copy the addresses from
the parent endpoint to the new endpoint. However, if the parent
was bound to a wildcard address, then we end up pointlessly copying
all of the current addresses on the system.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP accept code tries to add a newliy created socket
to a bind bucket without holding a lock. On a really
busy system, that can causes slab corruptions.
Add a lock around this code.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_rt_advice has been gone, so no need to keep prototype and debug message.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 stack doesn't reply any ICMP destination unreachable message
with net unreachable code when IP detagrams are being discarded
because of no route could be found in the forwarding path.
Incidentally, IPv6 stack replies such ICMPv6 message in the similar
situation.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert part of the led trigger core from rw spinlocks to rw
semaphores. We're calling functions which can sleep from invalid
contexts otherwise. Fixes bug #9264.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
IPv6 stack doesn't increment OutNoRoutes counter when IP datagrams
is being discarded because no route could be found to transmit them
to their destination. IPv6 stack should increment the counter.
Incidentally, IPv4 stack increments that counter in such situation.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: vmlinux.o(.init.text+0x204e2): Section mismatch: reference to .exit.text:br_fdb_fini (between 'br_init' and 'br_fdb_init')
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED in the current driver will not be controlled correctly. During
a link change the carrier of the link is not available and the LED
will never turn on.
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some systems report technology information with trailing spaces:
{pts/1}% cat -E /var/tmp/bat/2.6.23 | grep type
battery type: Li-ION $
Use strncasecmp to compare model string to skip trailing part
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The ml300 and ml403 xparameters.h files use different macros for the
AC97 interrupt pin assignments. This normalizes them to a canonical
value similar to what EDK generates for most other devices. This is
needed to get ml300 support to compile in arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old debugging hack sneaked back during x86 merge, this removes it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] lba_pci: pci_claim_resources disabled expansion roms
[PARISC] print more than one character at a time for pdc console
[PARISC] Update parisc-linux MAINTAINERS entries
[PARISC] timer interrupt should not be IRQ_DISABLED
Revert "[PARISC] import necessary bits of libgcc.a"
The size of swapper_pg_dir is 8k instead of 4k when using 64-bit PTEs
(CONFIG_PTE_64BIT).
This was reported by Cedric Hombourger <chombourger@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Oprofile: Fix computation of number of counters.
[MIPS] Alchemy: fix IRQ bases
[MIPS] Alchemy: replace ffs() with __ffs()
[MIPS] BCM1480: Fix interrupt routing, take 2.
Make the Kconfig.instrumentation file a bit easier on the eyes, and use
the new ARCH_SUPPORTS_OPROFILE for x86[-64].
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radeonfb was HPMC-ing my C8000 by trying to map its expansion rom from
IO_VIEW, instead of PA_VIEW. Fix seems to be to ensure that its disabled
ROM is properly inserted into the resource tree.
FIXME: this will result in a whinging printk for cards which share expansion
ROMS, such as a quad tulip. Thankfully, it isn't harmful.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The cleanup 09cadedbdc broke the oprofile
configuration for MIPS by allowing oprofile support to be built for
kernel models where oprofile doesn't have a chance in hell to work.
Just a dependecy list on a number of architectures is - surprise - broken
and should as per past discussions probably in most considered to be
broken in most cases. So I introduce a dependency for the oprofile
configuration on ARCH_SUPPORTS_OPROFILE.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's really no reason not to print more than one character at a
time to the PDC console... Booting is measurably speedier, and now I don't
have to watch individual characters get drawn.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The timer interrupt had accidentally been marked IRQ_DISABLED since
IRQ_PER_CPU had been OR-ed in, instead of set. This had been working
by accident for quite a while.
Commit c642b8391c changed the behaviour of
IRQ_PER_CPU interrupts, which previously weren't checked for IRQ_DISABLED.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This reverts commit efb80e7e09, it turned
out to cause sporadic problems with the timer interrupt on 32-bit kernels.
Needs more investigation.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
VSMP kernels will split the available performance counters between the two
processors / cores. But don't do this when we're not on a VSMP system ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix havoc wrought by commit 56f621c7f6 --
au_ffs() and ffs() are equivalent, that patch should have just replaced one
with another. Now replace ffs() with __ffs() which returns an unbiased bit
number.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This updates all the defconfigs in arch/powerpc/configs except iseries
and ps3, which were updated by the preceding commits.
This mostly takes the defaults, except that I turned on tickless idle
and high-resolution timers for everything, and turned off instrumentation
support and "Fair group CPU scheduler" for the smaller/embedded platforms.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The notable changes here are the enabling of NO_HZ and HIGH_RES_TIMERS.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The commit fa13a5a1f2 (sched: restore
deterministic CPU accounting on powerpc), unconditionally calls
update_process_tick() in system context. In the deterministic
accounting case this is the correct thing to do. However, in the
non-deterministic accounting case we need to not do this, since doing
this results in the time accounted as hardware irq time being
artificially elevated.
Also this collapses 2 consecutive '#ifdef CONFIG_VIRT_CPU_ACCOUNTING'
checks in time.h into one for neatness.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
VM/Security: add security hook to do_brk
Security: round mmap hint address above mmap_min_addr
security: protect from stack expantion into low vm addresses
Security: allow capable check to permit mmap or low vm space
SELinux: detect dead booleans
SELinux: do not clear f_op when removing entries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[LRO]: fix lro_gen_skb() alignment
[TCP]: NAGLE_PUSH seems to be a wrong way around
[TCP]: Move prior_in_flight collect to more robust place
[TCP] FRTO: Use of existing funcs make code more obvious & robust
[IRDA]: Move ircomm_tty_line_info() under #ifdef CONFIG_PROC_FS
[ROSE]: Trivial compilation CONFIG_INET=n case
[IPVS]: Fix sched registration race when checking for name collision.
[IPVS]: Don't leak sysctl tables if the scheduler registration fails.
endianness annotations in networking code had been in place for quite a
while; in particular, sin_port and s_addr are annotated as big-endian.
Code in ocfs2 had __force casts added apparently to shut the sparse
warnings up; of course, these days they only serve to *produce* warnings
for no reason whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BFS_FILEBLOCKS() expects struct bfs_inode * (on-disk data, with little-
endian fields), not struct bfs_inode_info * (in-core stuff, with host-
endian ones).
It's a macro and fields with the right names are present in
bfs_inode_info, so it compiles, but on big-endian host it gives bogus
results.
Introduced in commit f433dc5634 ("Fixes to
the BFS filesystem driver").
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that X86_32 is provided on Kconfig level for uml-i386, there's no
need to play with it explicitly on Makefile level anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
access_flags_to_mode() gets on-the-wire data (little-endian) and treats
it as host-endian.
Introduced in commit e01b640013 ("[CIFS]
enable get mode from ACL when cifsacl mount option specified")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.
Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.
This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: Ben Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_sysctl_table() can return NULL sometimes, e.g. when kmalloc()
returns NULL or when sysctl check fails.
I've also noticed, that many (most?) code in the kernel doesn't check for
the return value from register_sysctl_table() and later simply calls the
unregister_sysctl_table() with potentially NULL argument.
This is unlikely on a common kernel configuration, but in case we're
dealing with modules and/or fault-injection support, there's a slight
possibility of an OOPS.
Changing all the users to check for return code from the registering does
not look like a good solution - there are too many code doing this and
failure in sysctl tables registration is not a good reason to abort module
loading (in most of the cases).
So I think, that we can just have this check in unregister_sysctl_table
just to avoid accidental OOPS-es (actually, the unregister_sysctl_table()
did exactly this, before the start_unregistering() appeared).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status. In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible. The command sets are different, as
is the treatment of erasure. (FLASH needs explicit erasure, but
with EEPROM it's implicit.) Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes regression, introduced since 2.6.16. NextStep variant of
UFS as OpenStep uses directory block size equals to 1024. Without this
change, ufs_check_page fails in many cases.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Dave Bailey <dsbailey@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we are complicating the code in copy_process, the clone ABI, and
if we fix the bugs sys_setsid itself, with an unnecessary open coded
version of sys_setsid.
So just simplify everything and don't special case the session and pgrp of
the initial process in a pid namespace.
Having this special case actually presents to user space the classic linux
startup conditions with session == pgrp == 0 for /sbin/init.
We already handle sending signals to processes in a child pid namespace.
We need to handle sending signals to processes in a parent pid namespace
for cases like SIGCHILD and SIGIO.
This makes nothing extra visible inside a pid namespace. So this extra
special case appears to have no redeeming merits.
Further removing this special case increases the flexibility of how we can
use pid namespaces, by not requiring the initial process in a pid namespace
to be a daemon.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 2.6.24, top started showing 100% iowait on one CPU when a UML instance was
running (but completely idle). The UML code sits in io_getevents waiting for
an event to be submitted and completed.
Fix this by checking ctx->reqs_active before scheduling to determine whether
or not we are waiting for I/O.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Torsten Kaiser wrote:
| static inline int in_range(const void *start, const void *addr, const void *end)
| {
| return addr >= start && addr <= end;
| }
| This will return true, if addr is in the range of start (including)
| to end (including).
|
| But debug_check_no_locks_freed() seems does:
| const void *mem_to = mem_from + mem_len
| -> mem_to is the last byte of the freed range, that fits in_range
| lock_from = (void *)hlock->instance;
| -> first byte of the lock
| lock_to = (void *)(hlock->instance + 1);
| -> first byte of the next lock, not last byte of the lock that is being checked!
|
| The test is:
| if (!in_range(mem_from, lock_from, mem_to) &&
| !in_range(mem_from, lock_to, mem_to))
| continue;
| So it tests, if the first byte of the lock is in the range that is freed ->OK
| And if the first byte of the *next* lock is in the range that is freed
| -> Not OK.
We can also simplify in_range checks, we need only 2 comparisons, not 4.
If the lock is not in memory range, it should be either at the left of range
or at the right.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
style cleanup of various changes that were done recently.
no code changed:
text data bss dec hex filename
23680 2542 28 26250 668a sched.o.before
23680 2542 28 26250 668a sched.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Holmes found a bug in the -rt tree with respect to
pthread_cond_timedwait. After trying his test program on the latest git
from mainline, I found the bug was there too. The bug he was seeing
that his test program showed, was that if one were to do a "Ctrl-Z" on a
process that was in the pthread_cond_timedwait, and then did a "bg" on
that process, it would return with a "-ETIMEDOUT" but early. That is,
the timer would go off early.
Looking into this, I found the source of the problem. And it is a rather
nasty bug at that.
Here's the relevant code from kernel/futex.c: (not in order in the file)
[...]
smlinkage long sys_futex(u32 __user *uaddr, int op, u32 val,
struct timespec __user *utime, u32 __user *uaddr2,
u32 val3)
{
struct timespec ts;
ktime_t t, *tp = NULL;
u32 val2 = 0;
int cmd = op & FUTEX_CMD_MASK;
if (utime && (cmd == FUTEX_WAIT || cmd == FUTEX_LOCK_PI)) {
if (copy_from_user(&ts, utime, sizeof(ts)) != 0)
return -EFAULT;
if (!timespec_valid(&ts))
return -EINVAL;
t = timespec_to_ktime(ts);
if (cmd == FUTEX_WAIT)
t = ktime_add(ktime_get(), t);
tp = &t;
}
[...]
return do_futex(uaddr, op, val, tp, uaddr2, val2, val3);
}
[...]
long do_futex(u32 __user *uaddr, int op, u32 val, ktime_t *timeout,
u32 __user *uaddr2, u32 val2, u32 val3)
{
int ret;
int cmd = op & FUTEX_CMD_MASK;
struct rw_semaphore *fshared = NULL;
if (!(op & FUTEX_PRIVATE_FLAG))
fshared = ¤t->mm->mmap_sem;
switch (cmd) {
case FUTEX_WAIT:
ret = futex_wait(uaddr, fshared, val, timeout);
[...]
static int futex_wait(u32 __user *uaddr, struct rw_semaphore *fshared,
u32 val, ktime_t *abs_time)
{
[...]
struct restart_block *restart;
restart = ¤t_thread_info()->restart_block;
restart->fn = futex_wait_restart;
restart->arg0 = (unsigned long)uaddr;
restart->arg1 = (unsigned long)val;
restart->arg2 = (unsigned long)abs_time;
restart->arg3 = 0;
if (fshared)
restart->arg3 |= ARG3_SHARED;
return -ERESTART_RESTARTBLOCK;
[...]
static long futex_wait_restart(struct restart_block *restart)
{
u32 __user *uaddr = (u32 __user *)restart->arg0;
u32 val = (u32)restart->arg1;
ktime_t *abs_time = (ktime_t *)restart->arg2;
struct rw_semaphore *fshared = NULL;
restart->fn = do_no_restart_syscall;
if (restart->arg3 & ARG3_SHARED)
fshared = ¤t->mm->mmap_sem;
return (long)futex_wait(uaddr, fshared, val, abs_time);
}
So when the futex_wait is interrupt by a signal we break out of the
hrtimer code and set up or return from signal. This code does not return
back to userspace, so we set up a RESTARTBLOCK. The bug here is that we
save the "abs_time" which is a pointer to the stack variable "ktime_t t"
from sys_futex.
This returns and unwinds the stack before we get to call our signal. On
return from the signal we go to futex_wait_restart, where we update all
the parameters for futex_wait and call it. But here we have a problem
where abs_time is no longer valid.
I verified this with print statements, and sure enough, what abs_time
was set to ends up being garbage when we get to futex_wait_restart.
The solution I did to solve this (with input from Linus Torvalds)
was to add unions to the restart_block to allow system calls to
use the restart with specific parameters. This way the futex code now
saves the time in a 64bit value in the restart block instead of storing
it on the stack.
Note: I'm a bit nervious to add "linux/types.h" and use u32 and u64
in thread_info.h, when there's a #ifdef __KERNEL__ just below that.
Not sure what that is there for. If this turns out to be a problem, I've
tested this with using "unsigned int" for u32 and "unsigned long long" for
u64 and it worked just the same. I'm using u32 and u64 just to be
consistent with what the futex code uses.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
There should be an of_node_put when breaking out of a loop that iterates
using for_each_node_by_type.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for possible NULL pointer dereference
if of_find_property() failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a field to the lro_mgr struct so that drivers can specify how much
padding is required to align layer 3 headers when a packet is copied
into a freshly allocated skb by inet_lro.c:lro_gen_skb(). Without
padding, skbs generated by LRO will cause alignment warnings on
architectures which require strict alignment (seen on sparc64).
Myri10GE is updated to use this field.
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment in tcp_nagle_test suggests that. This bug is very
very old, even 2.4.0 seems to have it.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous location is after sacktag processing, which affects
counters tcp_packets_in_flight depends on. This may manifest as
wrong behavior if new SACK blocks are present and all is clear
for call to tcp_cong_avoid, which in the case of
tcp_reno_cong_avoid bails out early because it thinks that
TCP is not limited by cwnd.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though there's little need for everything that tcp_may_send_now
does (actually, even the state had to be adjusted to pass some
checks FRTO does not want to occur), it's more robust to let it
make the decision if sending is allowed. State adjustments
needed:
- Make sure snd_cwnd limit is not hit in there
- Disable nagle (if necessary) through the frto_counter == 2
The result of check for frto_counter in argument to call for
tcp_enter_frto_loss can just be open coded, therefore there
isn't need to store the previous frto_counter past
tcp_may_send_now.
In addition, returns can then be combined.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function in question is called only from ircomm_tty_read_proc,
which is under this option. Move this helper to the same place.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rose_rebuild_header() consists only of some variables in
case INET=n, and gcc will warn us about it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register_ip_vs_scheduler() checks for the scheduler with the
same name under the read-locked __ip_vs_sched_lock, then drops,
takes it for writing and puts the scheduler in list.
This is racy, since we can have a race window between the lock
being re-locked for writing.
The fix is to search the scheduler with the given name right under
the write-locked __ip_vs_sched_lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we load lblc or lblcr module we can leak some sysctl
tables if the call to register_ip_vs_scheduler() fails.
I've looked at the register_ip_vs_scheduler() code and saw, that
the only reason to fail is the name collision, so I think that
with some 3rd party schedulers this becomes a relevant issue. No?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a specifically crafted binary do_brk() can be used to get low
pages available in userspace virtually memory and can thus be used to
circumvent the mmap_min_addr low memory protection. Add security checks
in do_brk().
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
If mmap_min_addr is set and a process attempts to mmap (not fixed) with a
non-null hint address less than mmap_min_addr the mapping will fail the
security checks. Since this is just a hint address this patch will round
such a hint address above mmap_min_addr.
gcj was found to try to be very frugal with vm usage and give hint addresses
in the 8k-32k range. Without this patch all such programs failed and with
the patch they happily get a higher address.
This patch is wrappad in CONFIG_SECURITY since mmap_min_addr doesn't exist
without it and there would be no security check possible no matter what. So
we should not bother compiling in this rounding if it is just a waste of
time.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add security checks to make sure we are not attempting to expand the
stack into memory protected by mmap_min_addr
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
On a kernel with CONFIG_SECURITY but without an LSM which implements
security_file_mmap it is impossible for an application to mmap addresses
lower than mmap_min_addr. Based on a suggestion from a developer in the
openwall community this patch adds a check for CAP_SYS_RAWIO. It is
assumed that any process with this capability can harm the system a lot
more easily than writing some stuff on the zero page and then trying to
get the kernel to trip over itself. It also means that programs like X
on i686 which use vm86 emulation can work even with mmap_min_addr set.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Instead of using f_op to detect dead booleans, check the inode index
against the number of booleans and check the dentry name against the
boolean name for that index on reads and writes. This prevents
incorrect use of a boolean file opened prior to a policy reload while
allowing valid use of it as long as it still corresponds to the same
boolean in the policy.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Do not clear f_op when removing entries since it isn't safe to do.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Lately I've got this nice badness on mdio bus removal:
Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700 Not tainted (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR> CR: 24088422 XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...
Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.
This patch implement phy device's release function, thus
we're getting rid of this badness.
Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eliminate an uninitialized variable warning. The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we're freeing the skb when we detect CRC error, but we're
not clearing out info->skb. We could either clear it and have the stack
reallocate it, or just leave it and the rx ring refill code will reuse
the one that was allocated.
Reusing a freed skb obviously caused some nasty crashes of various kind,
as reported by Brent Baude and David Woodhouse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.
Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Don't program UDMA timings when programming PIO or MWDMA modes.
This has also a nice side-effect of fixing regression added by commit
681c80b5d9 ("libata: correct handling of
SRST reset sequences") (->set_piomode method for PIO0 is called before
->cable_detect method which checks UDMA timings to get the cable type).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: "Thomas Lindroth" <thomas.lindroth@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.
This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.
So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Make sure the restore psw masks are initialized.
[S390] Fix compile error on 31bit without preemption
[S390] dcssblk: prevent early access without own make_request function
[S390] cio: add missing reprobe loop end statement
[S390] cio: Issue SenseID per path.
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: default to more agressive yield for SCHED_BATCH tasks
sched: fix crash in sys_sched_rr_get_interval()
I haven't seen Richard doing MTRR related work for quite some time, and
the "X86 ARCHITECTURE" entry in MAINTAINERS already covers the people
currently responsible for this code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for the built-in watchdog on EPIC Nano 7240 boards from IEI.
Tested on Nano-7240RS.
Hardware documentation of the platform (including watchdog) can be found
on the IEI website: http://www.ieiworld.com
Signed-off-by: Gilles Gigan <gilles.gigan@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
fix this on i386 allnoconfig:
WARNING: vmlinux.o(.text+0x6f2e): Section mismatch: reference to .init.text:register_cpu (between 'arch_register_cpu' and 'text_poke')
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
free_cache_attributes() must be __cpuinit since it calls the
__cpuinit cache_remove_shared_cpu_map().
This patch fixes the following section mismatch reported by
Chris Clayton:
...
WARNING: vmlinux.o(.text+0x90b6): Section mismatch: reference to .init.text:cache_remove_shared_cpu_map (between 'free_cache_attributes' and 'show_level')
...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Our automated test suite looks for keywords like error, fail, warning in
the boot log. In the case when the nmi watchdog is determined to be
stuck in check_nmi_watchdog(), none of those keywords are displayed.
This patch adds a keyword, "WARNING:", so it makes it easier to notice
when the nmi watchdog isn't working correctly. Also add a proper
KERN_WARNING mark to this printout.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent Kconfig changes in x86 resulted in CONFIG_X86_HT no longer
being set if (X86_32 && MK8).
After grep'ing through the tree I think the problem is that different
places have different assumptions about the semantics of CONFIG_X86_HT,
either:
- hyperthreading or
- multicore
This should be sorted out properly, but until then we should keep the
2.6.23 status quo.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
do more agressive yield for SCHED_BATCH tuned tasks: they are all
about throughput anyway. This allows a gentler migration path for
any apps that relied on stronger yield.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Luiz Fernando N. Capitulino reported that sched_rr_get_interval()
crashes for SCHED_OTHER tasks that are on an idle runqueue.
The fix is to return a 0 timeslice for tasks that are on an idle
runqueue. (and which are not running, obviously)
this also shrinks the code a bit:
text data bss dec hex filename
47903 3934 336 52173 cbcd sched.o.before
47885 3934 336 52155 cbbb sched.o.after
Reported-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case of TRACE_IRQFLAGS the restore psw masks will not be
initialized if noexec is turned on. This will lead to an
immediate system crash.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit b8e7a54cd0 introduced a compile
error if CONFIG_PREEMPT is not set:
arch/s390/kernel/built-in.o: In function `cleanup_io_leave_insn':
/space/kvm/arch/s390/kernel/entry.S:(.text+0xbfce): undefined reference to `preempt_schedule_irq'
This patch hides preempt_schedule_irq if CONFIG_PREEMPT is not set.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When loading a dcss segment with the dcssblk driver, sometimes the
following kind of message appears:
bio too big device dcssblk0 (8 > 0)
Buffer I/O error on device dcssblk0, logical block 172016
..
The fix is to move the disk registration after setting the
make_request function, to avoid calls into generic_make_request
for dcssblock without having the make_request function set up
properly.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We may receive a unit check for every path when we issue a SenseID.
Unfortunately, the channel subsystem will try on a different path
every time if we use a lpm of 0xff, which will exhaust our retry
counter.
Therefore, revert SenseID to its previous per-path behaviour and
just leave out the suspend multipath reconnect.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix breakage caused by commit d5d8c5976d
"freezer: do not send signals to kernel threads" in
jffs2_garbage_collect_thread() that assumed it would be sent signals
by the freezer.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete MacKay <armlinux@architechnical.net>
Signed-off-by: Len Brown <len.brown@intel.com>
It's not permitted to unregister a device after devices have been suspended.
It causes deadlocks to appear on systems with coretemp hwmon loaded. To avoid
this, we can make coretemp_cpu_callback() do nothing if the _FROZEN bit is set
in action.
Also, in other cases it's generally too late to unregister the coretemp device
if the CPU is already dead, so it should be unregistered on CPU_DOWN_PREPARE.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: Support PCI IO access of SH7780 base boards.
sh: Fix PCI IO space base address of SH7780.
The old code did did only work as long as CFE and the kernel were using
the same interrupt numbering ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove xmon from ml300 and ml403 defconfig in arch/ppc
Revert "[POWERPC] Fix RTAS os-term usage on kernel panic"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: fix acpi-cpufreq boot crash due to _PSD return-by-reference
ACPI: Delete the IRQ operation in throttling controll via PTC
pageexec@freemail.hu writes:
> i've just noticed that the chunk in i386/kernel/head.S ended up in a
> weird place, namely, it's not going to be executed as it's just after
> a 'jmp 3f' and before startup_32_smp, probably not what you intended.
> on a sidenote, the whole thing can be done in a single insn, like:
>
> movl $(swapper_pg_pmd - __PAGE_OFFSET + 0x067), (swapper_pg_dir -
> __PAGE_OFFSET+ 4092)
Thanks for the reminder I thought we had fixed this problem a while ago.
Needed to get fixed virtual address for USB debug and earlycon with mmio.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
LIB82596: correct data types for hardware addresses
via-velocity: don't oops on MTU change (resend)
Stop phy code from returning success to unknown ioctls.
SET_NETDEV_DEV() in fec_mpc52xx.c
net: smc911x: only enable for mpr2 on sh.
e1000: Fix NAPI state bug when Rx complete
sky2: turn of dynamic Tx watermark workaround (FE+ only)
sky2: don't use AER routines
sky2: revert to access PCI config via device space
cxgb - fix stats
cxgb - fix NAPI
cxgb - fix T2 GSO
ucc_geth: handle passing of RX-only and TX-only internal delay PHY connection type parameters
phylib: marvell: add support for TX-only and RX-only Internal Delay
phylib: add PHY interface modes for internal delay for tx and rx only
skge: MTU changing fix
skge: serial mode register values
skge version 1.13
skge: increase TX threshold for Jumbo
skge: fiber link up/down fix
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix broken Marvell 7042 support.
libata: Fix early use of port printk. (Was Re: ata4294967295: failed to start port (errno=-19))
ata_piix: add more toshiba laptops to broken suspend list
libata: More IVB horkage from TSST
libata: report protocol and full CDB on error
Several fixes for the AVR32 PATA driver
sata_mv: fix compilation error when enabling DEBUG
Set proper ATA UDMA mode for bf548 according to system clock.
Under the conditions that UML uses it, tcgetattr is guaranteed to return
-EINTR when the console is attached to /dev/ptmx, making generic_console_write
hang because it loops, calling tcgetattr until it succeeds. This is a host
bug - see http://marc.info/?l=linux-kernel&m=119618990807182&w=2 for the
details.
This patch works around it by blocking SIGIO while the terminal attributes are
being fiddled.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a UML build breakage introduced by commit
1032c0ba9d - it introduces X86_32, with many
things which UML needs depending on it.
This patch adds definitions of X86_32 and RWSEM_XCHGADD_ALGORITHM to
the UML/i386 Kconfig.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The inet_diag register fix broke inet_diag module loading because the
loaded module had to take the same mutex that's already held by the
loader in order to register the new handler.
This patch fixes it by introducing a separate mutex to protect the
handling of handlers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
xmon is broken under arch/ppc so remove it from the defconfig.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed resolution of named references in packages
Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.
http://bugzilla.kernel.org/show_bug.cgi?id=5328http://bugzilla.kernel.org/show_bug.cgi?id=9429
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit cfb5285660 removed a useful feature for
us, which provided a cpu accounting resource controller. This feature would be
useful if someone wants to group tasks only for accounting purpose and doesnt
really want to exercise any control over their cpu consumption.
The patch below reintroduces the feature. It is based on Paul Menage's
original patch (Commit 62d0df6406), with
these differences:
- Removed load average information. I felt it needs more thought (esp
to deal with SMP and virtualized platforms) and can be added for
2.6.25 after more discussions.
- Convert group cpu usage to be nanosecond accurate (as rest of the cfs
stats are) and invoke cpuacct_charge() from the respective scheduler
classes
- Make accounting scalable on SMP systems by splitting the usage
counter to be per-cpu
- Move the code from kernel/cpu_acct.c to kernel/sched.c (since the
code is not big enough to warrant a new file and also this rightly
needs to live inside the scheduler. Also things like accessing
rq->lock while reading cpu usage becomes easier if the code lived in
kernel/sched.c)
The patch also modifies the cpu controller not to provide the same accounting
information.
Tested-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Tested the patches on top of 2.6.24-rc3. The patches work fine. Ran
some simple tests like cpuspin (spin on the cpu), ran several tasks in
the same group and timed them. Compared their time stamps with
cpuacct.usage.
Signed-off-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.
This fixes an oops on T61 -- a regression due to
f79f06ab9f b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:
> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.
Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add more toshiba laptops to broken suspend list. This is from OSDL
bugzilla bug 7780.
tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.
signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands. Report them on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several fixes for the AVR32 PATA driver:
* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.
* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.
* Removed .port_disable and .irq_ack as these are no longer needed.
* Improved some comments.
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This kind of sucks, and prevents the Fedora installer from using the
device for network installs...
[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...
eth0 ESSID:off/any Nickname:""
NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0
Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0
RTS thr:off Fragment thr:off
Encryption key:<too big>
Power Management:off
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This helps to allow the Fedora installer to use the built-in Ethernet on
the Efika for a network install.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x.h is a bit of a mess, not supporting any sort of generic
configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have
suitable definitions, so we reflect this in the Kconfig also.
While there are other SH boards that will likely turn this on in the
2.6.25 time frame, it's not worth trying to stub around at the moment.
Fixes up the allmodconfig build, as noted by akpm.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.
This reverts 555382cbfc
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.
Reverts: 167f53d05f
Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netif_rx_complete() should be called only
when work_done < budget.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting. On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.
Resloves problem described in: http://lkml.org/lkml/2007/11/6/395
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently ctc-device initialization is broken (kernel bug in
ctc_new_device).
The new network namespace code reveals a deficiency of the
ctc driver. It should make use of alloc_netdev() as described
in Documentation/networking/netdevices.txt.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Well I clearly goofed when I added the initial network namespace support
for /proc/net. Currently things work but there are odd details visible to
user space, even when we have a single network namespace.
Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.
To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.
As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix static rate if path faster than link
IPoIB: Fix oops if xmit is called when priv->broadcast is NULL
Freeing prom memory: 956kb freed
Freeing firmware memory: 978944k freed
Freeing unused kernel memory: 180k freed
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/1
caller is r4k_dma_cache_wback_inv+0x144/0x2a0
Call Trace:
[<80117af8>] r4k_dma_cache_wback_inv+0x144/0x2a0
[<802e4b84>] debug_smp_processor_id+0xd4/0xf0
[<802e4b7c>] debug_smp_processor_id+0xcc/0xf0
...
CONFIG_DEBUG_PREEMPT is enabled.
--
Bug cause is blast_dcache_range() in preemptible code [in
r4k_dma_cache_wback_inv()].
blast_dcache_range() is constructed via __BUILD_BLAST_CACHE_RANGE that
uses cpu_dcache_line_size(). It uses current_cpu_data that use
smp_processor_id() in turn. In case of CONFIG_DEBUG_PREEMPT
smp_processor_id emits BUG if we are executing with preemption
enabled.
Cpu options of cpu0 are assumed to be the superset of all processors.
Can I make the same assumptions for cache line size and fix this
issue the following way:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
The database performance group have found that half the cycles spent
in kmem_cache_free are spent in this one call to BUG_ON. Moving it
into the CONFIG_SLAB_DEBUG-only function cache_free_debugcheck() is a
performance win of almost 0.5% on their particular benchmark.
The call was added as part of commit ddc2e812d5
with the comment that "overhead should be minimal". It may have been
minimal at the time, but it isn't now.
[ Quoth Pekka Enberg: "I don't think the BUG_ON per se caused the
performance regression but rather the virt_to_head_page() changes to
virt_to_cache() that were added later." ]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a zero length pattern is passed then return EINVAL.
Avoids infinite loops (bm) or invalid memory accesses (kmp).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
When xt_CONNMARK is used outside the mangle table and the user specified
"--restore-mark", the connmark_tg_check() function will (correctly)
error out, but (incorrectly) forgets to release the L3 conntrack module.
Same for xt_CONNSECMARK.
Fix is to move the call to acquire the L3 module after the basic
constraint checks.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As far as I see from the err variable initialization
the dn_nl_deladdr() routine was designed to report errors
like "EADDRNOTAVAIL" and probaby "ENODEV".
But the code sets this err to 0 after the first nlmsg_parse
and goes on, returning this 0 in any case.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avaid provided test application, so bug got fixed.
IPv6 addrconf removes ipv6 inner device from netdev each time cmu
changes and new value is less than IPV6_MIN_MTU (1280 bytes).
When mtu is changed and new value is greater than IPV6_MIN_MTU,
it does not add ipv6 addresses and inner device bac.
This patch fixes that.
Tested with Avaid's application, which works ok now.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The IO access of PCI is not supported in R7780RP and the MS7780SE
board now. The support of the IO access mode of e100 and a lot of IDE
chips becomes possible by fixing the code.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PCI IO space base address of SH7780 was wrong.
Change from 0xFE400000 to 0xFE200000.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attached patch rate limits "WEP decrypt failed (ICV)" to avoid
flooding the logfiles.
Signed-off-by: Adel Gadllah <adel.gadllah@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_toggle_radio is called from functions where
rfkill->mutex is already aquired.
Remove the lock from rfkill_toggle_radio() and add it to
the only calling function that calls it without the lock held.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression I (most likely) introduced, namely that
unencrypted frames are right now accepted even if we have a key for that
specific sender. That has very bad security implications.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes:
- Incorrect calls to ieee80211_hw_config when the radiotap flag is set.
- Failure to actually unset the radiotap flag when all monitors are down.
- Failure to call ieee80211_hw_config after successful interface start.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no guarantee that data+SNAP_SIZE will reside on an even numbered
address, so doing a 16 bit read will cause an unaligned access in some
situations. Based on a patch from Jun Sun.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure if this is best choice, someone might have better
solutions. But this patch fixed the connection problem when switching
from a WPA enabled AP (using wpa_supplicant) to an open AP (using
iwconfig). The root cause is when we connect to a WPA enabled AP,
wpa_supplicant sets the ifsta->extra_ie thru SIOCSIWGENIE. But if we
stop wpa_supplicant and connect to an open AP with iwconfig, there is
no way to clear the extra_ie so that mac80211 keeps connecting with that.
Someone could argue wpa_supplicant should clear the extra_ie during
its shutdown. But mac80211 should also handle the unexpected shutdown
case (ie. killall -9 wpa_supplicant).
On Wed, 2007-11-21 at 16:19 +0100, Johannes Berg wrote:
> Yeah. Can you amend the patch to also clear the
> IEEE80211_STA_PRIVACY_INVOKED flag?
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If NR_IRQS is defined as a sum without surrounding parentheses, this may
lead to problems when used in multiplications. This may lead to problems
in:
arch/ia64/sn/kernel/irq.c:516
arch/x86/kernel/io_apic_32.c:693, 694, 699, 700
fs/proc/proc_misc.c:464
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be
higher than default to cope with the fast PCLK frequency.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In wait_task_stopped() exit_code already contains the right value for the
si_status member of siginfo, and this is simply set in the non WNOWAIT
case.
If you call waitid() with a stopped or traced process, you'll get the signal
in siginfo.si_status as expected -- however if you call waitid(WNOWAIT) at the
same time, you'll get the signal << 8 | 0x7f
Pass it unchanged to wait_noreap_copyout(); we would only need to shift it
and add 0x7f if we were returning it in the user status field and that
isn't used for any function that permits WNOWAIT.
Signed-off-by: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arrange the sections in the FRV arch so that a BRA instruction with a
16-bit displacement can always reach from the trap table to entry.S,
tlb-miss.S and break.S.
The problem otherwise is that the linker can insert sufficient code between
the slots in the trap table and the targets of the branch instructions in
those slots that the displacement field in the instruction isn't
sufficiently large. This is because the branch targets were in the .text
section along with most of the other code in the kernel.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the extern declaration of kallsyms_num_syms to indicate that the symbol
does not reside in the small-data storage space, and so may not be accessed
relative to the small data base register.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC code is using mutex to assure exclusive access to /dev/rtc. This is
however wrong usage, as it leaves the mutex locked when returning into
userspace, which is unacceptable.
Convert rtc->char_lock into bit operation.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found problems accessing (executing) previously existing files, until
I did chmod on them (or setattr).
If the fi->attr_version is not initialized, then it could be
larger than fc->attr_version until a setattr is executed, and as a
result the inode attributes would never be set.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUSE_FILE_OPS is meant to signal that the kernel will send the open file to to
the userspace filesystem for operations on open files, so that sillyrenaming
unlinked files becomes unnecessary.
However this needs VFS changes, which won't make it into 2.6.24.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some open flags (O_APPEND, O_DIRECT) can be changed with fcntl(F_SETFL, ...)
after open, but fuse currently only sends the flags to userspace in open.
To make it possible to correcly handle changing flags, send the
current value to userspace in each read and write.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently reading a fuse file will stop at cached i_size and return
EOF, even though the file might have grown since the attributes were
last updated.
So detect if trying to read past EOF, and refresh the attributes
before continuing with the read.
Thanks to mpb for the report.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds Graphics Output Protocol support to the kernel. UEFI2.0 spec
deprecates Universal Graphics Adapter (UGA) protocol and only Graphics Output
Protocol (GOP) is produced. Therefore, the boot loader needs to query the
UEFI firmware with appropriate Output Protocol and pass the video information
to the kernel. As a result of GOP protocol, an EFI framebuffer driver is
needed for displaying console messages. The patch adds a EFI framebuffer
driver. The EFI frame buffer driver in this patch is based on the Intel Mac
framebuffer driver.
The ELILO bootloader takes care of passing the video information as
appropriate for EFI firmware.
The framebuffer driver has been tested in i386 kernel and x86_64 kernel on EFI
platform.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7eea436433.
Lucy said:
This patch will work with the 19HS but WILL BREAK all other Keyspan
adapters. It will take me a few days to get to looking at a correct fix but
that keyspan_send_setup(port, 1) (and the '1' is the important part) must
happen once when the port is first opened. The cflag can just be set to
whatever the normal default is for your serial environment.
So revert this again pending the proper fix.
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With NO_HZ disabled, the UML idle loop effectively becomes a busy loop, as
it will sleep for no time.
The cause was forgetting to restart the tick after waking up from sleep.
It was disabled before sleeping, and the remaining time used as the
interval to sleep. So, the tick needs to be restarted when nanosleep
finishes.
This is done by introducing after_sleep_interval, which is empty in the
NO_HZ case, but which sets the tick starting in the !NO_HZ case.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
got this HiSax bootup crash on a "make randconfig" bzImage bootup:
Calling initcall 0xc0bb1320: HiSax_init+0x0/0x380()
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (kernel)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: HFC-S driver Rev. 1.10.2.4
HFCS: defined at 0x500 IRQ 5 HZ 250
Teles 16.3c: IRQ 5 count 0
HFCS: resetting card
Teles 16.3c: IRQ 5 count 0
Teles 16.3c: IRQ(5) getting no interrupts during init 1
HFCS: resetting card
------------[ cut here ]------------
kernel BUG at include/linux/timer.h:145!
invalid opcode: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
Modules linked in:
Pid: 1, comm: swapper Not tainted (2.6.24-rc3 #2045)
EIP: 0060:[<c063afbf>] EFLAGS: 00010286 CPU: 0
EIP is at hfcs_card_msg+0x15f/0x180
EAX: c0cf2e5c EBX: 000000f2 ECX: 00000000 EDX: ffff1193
ESI: f76e8000 EDI: f76e8000 EBP: f7c23ec4 ESP: f7c23eac
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process swapper (pid: 1, ti=f7c22000 task=f7c0e000 task.ti=f7c22000)
Stack: 00000000 f7c23ec4 c011703b 00000002 f76e8000 00000000 f7c23ef8 c060c3e5
c0a7c9c0 c0a315dc 00000005 00000001 00000000 f7c23f34 00000000 c0b5c9c0
f7c23f34 00000000 c0f5a8e0 f7c23f80 c0bb154f 00000000 00000001 c0a9b5b9
Call Trace:
[<c010339a>] show_trace_log_lvl+0x1a/0x40
[<c0103469>] show_stack_log_lvl+0xa9/0xe0
[<c010355f>] show_registers+0xbf/0x200
[<c01037a4>] die+0x104/0x220
[<c0103943>] do_trap+0x83/0xc0
[<c0103ca8>] do_invalid_op+0x88/0xa0
[<c083621a>] error_code+0x6a/0x70
[<c060c3e5>] checkcard+0x4a5/0x620
[<c0bb154f>] HiSax_init+0x22f/0x380
[<c0b867b7>] kernel_init+0x97/0x2a0
[<c0102f87>] kernel_thread_helper+0x7/0x20
=======================
Code: e8 43 ae ff 8b 57 3c 85 d2 0f 84 ef fe ff ff b8 a0 99 ad c0 b9 02 00 00 00 e8 ce 11 ae ff 83 c4 0c b8 00 00 00 00 5b 5e 5f c9 c3 <0f> 0b eb fe 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
EIP: [<c063afbf>] hfcs_card_msg+0x15f/0x180 SS:ESP 0068:f7c23eac
Kernel panic - not syncing: Attempted to kill init!
The box has no HiSax card installed.
the reason for the crash is add_timer() done on an already running
timer. This happens because for some reason CARD_INIT is called twice.
this patch works this problem around by using mod_timer() - this gets
a booting system - but it would be nice to figure out why CARD_INIT
is done twice.
the ISDN config section (generated via make randconfig) is this:
#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
CONFIG_ISDN_DIVERSION=y
#
# ISDN4Linux hardware drivers
#
#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=y
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8
#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
CONFIG_HISAX_S0BOX=y
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
CONFIG_HISAX_HFCS=y
# CONFIG_HISAX_SEDLBAUER is not set
CONFIG_HISAX_SPORTSTER=y
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set
#
# HiSax PCMCIA card service modules
#
#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=y
CONFIG_HISAX_HFCUSB=y
# CONFIG_HISAX_HFC4S8S is not set
CONFIG_HISAX_FRITZ_PCIPNP=y
CONFIG_HISAX_HDLC=y
#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=y
# CONFIG_ISDN_DRV_ACT2000 is not set
CONFIG_HYSDN=m
# CONFIG_ISDN_DRV_GIGASET is not set
# CONFIG_ISDN_CAPI is not set
CONFIG_PHONE=y
CONFIG_PHONE_IXJ=m
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Kai Germaschewski <kai@germaschewski.name>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An unprivileged process must be able to kill a setuid root program started
by the same user. This is legacy behavior needed for instance for xinit to
kill X when the window manager exits.
When an unprivileged user runs a setuid root program in !SECURE_NOROOT
mode, fP, fI, and fE are set full on, so pP' and pE' are full on. Then
cap_task_kill() prevents the user from signaling the setuid root task.
This is a change in behavior compared to when
!CONFIG_SECURITY_FILE_CAPABILITIES.
This patch introduces a special check into cap_task_kill() just to check
whether a non-root user is signaling a setuid root program started by the
same user. If so, then signal is allowed.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Andrew Morgan <morgan@kernel.org>
Cc: Stephen Smalley <sds@epoch.ncsc.mil>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: James Morris <jmorris@namei.org>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit a686cd898b:
"Val's cross-port of the ext3 reservations code into ext2."
include/linux/ext2_fs.h got a new function whose return value is only
defined if __KERNEL__ is defined. Putting #ifdef __KERNEL__ around the
function seems to help, patch below.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch corrects recently changed (and now invalid) Kconfig descriptions
for the DMA engine framework:
- Non-Intel(R) hardware also has DMA engines;
- DMA is used for more than memcpy and RAID offloading.
In fact, on most platforms memcpy and RAID aren't factors, and DMA
exists so that peripherals can transfer data to/from memory while
the CPU does other work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an additional loop, that delays turning off the DMA
until the LCDC core has been turned off. This prevents the picture
to be shifted some random length when the kernel re-initializes
the LCDC.
Without this patch, the LCDC keeps running for some small time after the
PWRCON:LCD_PWR has been cleared ; the FIFO suffers an underrun and on
re-starting the LCDC the FIFO data stays shifted.
This behavior has been seen and fixed on AT91SAM9261-EK and two custom
AT91SAM9261 boards, all of them having different LCD panels.
Thanks a lot to Anti Sullin for submitting this patch (long
time ago).
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
People discuss how the namespaces are working/going-to-work together.
Ted Ts'o proposed to create some document that describes what problems user
may have when he/she creates some new namespace, but keeps others shared.
I liked this idea, so here's the initial version of such a document with
the problems I currently have in mind and can describe somewhat audibly -
the "namespaces compatibility list".
The Documentation/namespaces/ directory is about to contain more docs about
the namespaces stuff.
Thanks to Cedirc for notes and spell checks on the doc, to Daniel for
additional info about IPC and User namespaces interaction and to Randy, who
alluded me to using a spell checker before sending the documentation :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 7d69a1f4a7 ("remove CONFIG_UTS_NS
and CONFIG_IPC_NS") by Cedric Le Goater accidentally removed the code
that prevented the uts->hostname and uts->domainname values from being
overwritten from another namespace.
In other words, setting hostname/domainname via sysfs (echo xxx >
/proc/sys/kernel/(host|domain)name) cased the new value to be set in
init UTS namespace only.
Return the isolation back.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Cedric Le Goater <clg@fr.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
This was fixed using the following semantic patch.
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@
T *d;
...
for_each_pci_dev(d)
{... when != pci_dev_put(d)
when != e = d
(
return d;
|
+ pci_dev_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Greg KH <greg@kroah.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in fb_ddc_read() is said to be based on the implementation of the
radeon driver:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=fc5891c8a3ba284f13994d7bc1f1bfa8283982de
However, comparing the old radeon driver code with the new fb_ddc code
reveals some differences. Most notably, the I2C bus lines are held at the
end of the function, while the original code was releasing them (as the
comment above correctly says.)
There are a few other differences, which appear to be responsible for read
failures on my system. While tracing low-level I2C code in i2c-algo-bit, I
noticed that the initial attempt to read the EDID always failed. It takes
one retry for the read to succeed. As we are about to remove this
automatic retry property from i2c-algo-bit, reading the EDID would really
fail.
As a summary, the I2C lines quirk which is supposedly needed to read EDID
on some older monitors is currently breaking the (first) read on all other
monitors (and might not even work with older ones - did anyone try since
October 2006?)
After applying the patch below, which makes the code in fb_ddc_read()
really similar to what the radeon driver used to have, the first EDID read
succeeds again.
On top of that, as it appears that this code has been broken for one year
now and nobody seems to have complained, I'm curious if it makes sense to
keep this quirk in place. It makes the code more complex and slower just
for the sake of monitors which I guess nobody uses anymore. Can't we just
get rid of it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Roger Leigh <rleigh@whinlatter.ukfsn.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For reasons unclear to me, glibc's <sys/kd.h> deliberately defeats the
attempt we make in <linux/kd.h> to include <linux/types.h>
For now, change the one instance of __u32 to 'unsigned int' instead
because it's breaking userspace. We should probably also remove our
inclusion of <linux/types.h>, since we don't use it -- but that's not a
change to make in -rc.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we specify an GPIO which cannot be used for the purpose, then assume
that the GPIO is not to be used and do not try and configure it. This can
be the case where the SPI bus is TX only.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the initialization of the TPM TIS driver, the necessary locality has
to be requested earlier in the init-process. Depending on the used TPM
chip, this leads to wrong information. For example: Lenovo X61s with Atmel
TPM:
tpm_tis 00:0a: 1.2 TPM (device-id 0xFFFF, rev-id 255)
But correct is:
tpm_tis 00:0c: 1.2 TPM (device-id 0x3203, rev-id 9)
This short patch fixes this issue.
Signed-off-by: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg noticed that the call of task_pid_nr_ns() in proc_pid_readdir
is racy with respect to tasks exiting.
After a bit of examination it also appears that the call itself
is completely unnecessary.
So to fix the problem this patch modifies next_tgid() to return
both a tgid and the task struct in question.
A structure is introduced to return these values because it is
slightly cleaner and easier to optimize, and the resulting code
is a little shorter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc_kill_inodes() can clear ->i_fop in the middle of vfs_readdir resulting in
NULL dereference during "file->f_op->readdir(file, buf, filler)".
The solution is to remove proc_kill_inodes() completely:
a) we don't have tricky modules implementing their tricky readdir hooks which
could keeping this revoke from hell.
b) In a situation when module is gone but PDE still alive, standard
readdir will return only "." and "..", because pde->next was cleared by
remove_proc_entry().
c) the race proc_kill_inode() destined to prevent is not completely
fixed, just race window made smaller, because vfs_readdir() is run
without sb_lock held and without file_list_lock held. Effectively,
->i_fop is cleared at random moment, which can't fix properly anything.
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000018
printing eip: c1061205 *pdpt = 0000000005b22001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: foo af_packet ipv6 cpufreq_ondemand loop serio_raw sr_mod k8temp cdrom hwmon amd_rng
Pid: 2033, comm: find Not tainted (2.6.24-rc1-b1d08ac064268d0ae2281e98bf5e82627e0f0c56 #2)
EIP: 0060:[<c1061205>] EFLAGS: 00010246 CPU: 0
EIP is at vfs_readdir+0x47/0x74
EAX: c6b6a780 EBX: 00000000 ECX: c1061040 EDX: c5decf94
ESI: c6b6a780 EDI: fffffffe EBP: c9797c54 ESP: c5decf78
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process find (pid: 2033, ti=c5dec000 task=c64bba90 task.ti=c5dec000)
Stack: c5decf94 c1061040 fffffff7 0805ffbc 00000000 c6b6a780 c1061295 0805ffbc
00000000 00000400 00000000 00000004 0805ffbc 4588eff4 c5dec000 c10026ba
00000004 0805ffbc 00000400 0805ffbc 4588eff4 bfdc6c70 000000dc 0000007b
Call Trace:
[<c1061040>] filldir64+0x0/0xc5
[<c1061295>] sys_getdents64+0x63/0xa5
[<c10026ba>] sysenter_past_esp+0x5f/0x85
=======================
Code: 49 83 78 18 00 74 43 8d 6b 74 bf fe ff ff ff 89 e8 e8 b8 c0 12 00 f6 83 2c 01 00 00 10 75 22 8b 5e 10 8b 4c 24 04 89 f0 8b 14 24 <ff> 53 18 f6 46 1a 04 89 c7 75 0b 8b 56 0c 8b 46 08 e8 c8 66 00
EIP: [<c1061205>] vfs_readdir+0x47/0x74 SS:ESP 0068:c5decf78
hch: "Nice, getting rid of this is a very good step formwards.
Unfortunately we have another copy of this junk in
security/selinux/selinuxfs.c:sel_remove_entries() which would need the
same treatment."
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some systems the number of resources(IO,MEM) returnedy by PNP device is
greater than the PNP constant, for example motherboard devices. It brings
that some resources can't be reserved and resource confilicts. This will
cause PCI resources are assigned wrongly in some systems, and cause hang.
This is a regression since we deleted ACPI motherboard driver and use PNP
system driver.
[akpm@linux-foundation.org: fix text and coding-style a bit]
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_PAGE_PCD maps a page with caching disabled, which is typically used for
mapping harware registers. Xen never allows it to be set on a mapping, and
unprivileged guests never need it since they can't see the real underlying
hardware. However, some uncached mappings are made early when probing the
(non-existent) APIC, and its OK to mask off the PCD flag in these cases.
This became necessary because Xen started checking for this bit, rather
than silently masking it off.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ordinarily the size of a pageblock is determined at compile-time based on the
hugepage size. On PPC64, the hugepage size is determined at runtime based on
what is supported by the machine. With legacy machines such as iSeries that
do not support hugepages, HPAGE_SHIFT is 0. This results in pageblock_order
being set to -PAGE_SHIFT and a crash results shortly afterwards.
This patch adds a function to select a sensible value for pageblock order by
default when HUGETLB_PAGE_SIZE_VARIABLE is set. It checks that HPAGE_SHIFT
is a sensible value before using the hugepage size; if it is not MAX_ORDER-1
is used.
This is a fix for 2.6.24.
Credit goes to Stephen Rothwell for identifying the bug and testing candidate
patches. Additional credit goes to Andy Whitcroft for spotting a problem
with respects to IA-64 before releasing. Additional credit to David Gibson
for testing with the libhugetlbfs test suite.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Limit video memory size to avoid crossing a 256 MiB boundary in IOIF space.
- Pass the actual amount of video memory used to lv1_gpu_memory_allocate().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version brings a new terse output mode as well as many improvements to
the unary detection and bare type regcognition. It also brings the usual
updates for false positives, though these seem to be slowing markedly
now that the unary detector is no longer just putting its finger in the
air and guessing. Of note:
- new --terse mode producing a single line per report
- loosening of the block brace checks
- new checks for enum/union/struch brace placements
- hugely expanded "bare type" detection
- checks for inline usage
- better handling of already open comment blocks
- handle patches which introduce or remove lines without newlines
Andy Whitcroft (19):
Version: 0.12
style fixes as spotted by checkpatch
add a --terse options of a single line of output per report
block brace checks should only apply for single line blocks
all new bare type detector
check spacing for open braces with enum, union and struct
check for LINUX_VERSION_CODE
macros definition bracketing checks need to ignore -ve context
clean up the mail-back mode, -q et al
expand possible type matching to declarations
allow const and sparse annotations on possible types
handle possible types as regular types everywhere
prefer plain inline over __inline__ and __inline
all new open comment detection
fix up conditional extraction for if assignment checks
add const to the possible type matcher
unary checks: a for loop is a conditional too
possible types: detect function pointer definitions
handle missind newlines at end of file, report addition
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SCTP-AUTH requires selection of CRYPTO, HMAC and SHA1 since
SHA1 is a MUST requirement for AUTH. We also support SHA256,
but that's optional, so fix the code to treat it as such.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
In the case where no autheticated chunks were specified, we were still
trying to verify that a given chunk needs authentication and doing so
incorrectly. Add a check for parameter length to make sure we don't
try to use an empty auth_chunks parameter to verify against.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Supported extensions parameter was not coded right and ended up
over-writing memory or causing skb overflows. First, remove
the FWD_TSN support from as it shouldn't be there and also fix
the paramter encoding.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
There was a typo that cleared the HMACS parameters when no
authenticated chunks were specified. We whould be clearing
the chunks pointer instead of the hmacs.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Our treatment of Heartbeats is special in that the inital HB chunk
counts against the error count for the association, where as for
other chunks, only retransmissions or timeouts count against us.
As a result, we had an off-by-1 situation with a number of
Heartbeats we could send.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Lachlan Andrew observed that my TCP-Illinois implementation uses the
beta value incorrectly:
The parameter beta in the paper specifies the amount to decrease
*by*: that is, on loss,
W <- W - beta*W
but in tcp_illinois_ssthresh() uses beta as the amount
to decrease *to*: W <- beta*W
This bug makes the Linux TCP-Illinois get less-aggressive on uncongested network,
hurting performance. Note: since the base beta value is .5, it has no
impact on a congested network.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Andrew Morton reported that __xfrm_lookup generates this warning:
net/xfrm/xfrm_policy.c: In function '__xfrm_lookup':
net/xfrm/xfrm_policy.c:1449: warning: 'dst' may be used uninitialized in this function
This is because if policy->action is of an unexpected value then dst will
not be initialised. Of course, in practice this should never happen since
the input layer xfrm_user/af_key will filter out all illegal values. But
the compiler doesn't know that of course.
So this patch fixes this by taking the conservative approach and treat all
unknown actions the same as a blocking action.
Thanks to Andrew for finding this and providing an initial fix.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following race is possible when one cpu unregisters the handler
while other one is trying to receive a message and call this one:
CPU1: CPU2:
inet_diag_rcv() inet_diag_unregister()
mutex_lock(&inet_diag_mutex);
netlink_rcv_skb(skb, &inet_diag_rcv_msg);
if (inet_diag_table[nlh->nlmsg_type] ==
NULL) /* false handler is still registered */
...
netlink_dump_start(idiagnl, skb, nlh,
inet_diag_dump, NULL);
cb = kzalloc(sizeof(*cb), GFP_KERNEL);
/* sleep here freeing memory
* or preempt
* or sleep later on nlk->cb_mutex
*/
spin_lock(&inet_diag_register_lock);
inet_diag_table[type] = NULL;
... spin_unlock(&inet_diag_register_lock);
synchronize_rcu();
/* CPU1 is sleeping - RCU quiescent
* state is passed
*/
return;
/* inet_diag_dump is finally called: */
inet_diag_dump()
handler = inet_diag_table[cb->nlh->nlmsg_type];
BUG_ON(handler == NULL);
/* OOPS! While we slept the unregister has set
* handler to NULL :(
*/
Grep showed, that the register/unregister functions are called
from init/fini module callbacks for tcp_/dccp_diag, so it's OK
to use the inet_diag_mutex to synchronize manipulations with the
inet_diag_table and the access to it.
Besides, as Herbert pointed out, asynchronous dumps should hold
this mutex as well, and thus, we provide the mutex as cb_mutex one.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This hook is protected with the RCU, so simple
if (br_should_route_hook)
br_should_route_hook(...)
is not enough on some architectures.
Use the rcu_dereference/rcu_assign_pointer in this case.
Fixed Stephen's comment concerning using the typeof().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case the br_netfilter_init() (or any subsequent call)
fails, the br_fdb_fini() must be called to free the allocated
in br_fdb_init() br_fdb_cache kmem cache.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
I am not absolutely sure whether this actually is a bug (as in: I've got
no clue what the standards say or what other implementations do), but at
least I was pretty surprised when I noticed that a recv() on a
non-blocking unix domain socket of type SOCK_SEQPACKET (which is connection
oriented, after all) where the remote end has closed the connection
returned -1 (EAGAIN) rather than 0 to indicate end of file.
This is a test case:
| #include <sys/types.h>
| #include <unistd.h>
| #include <sys/socket.h>
| #include <sys/un.h>
| #include <fcntl.h>
| #include <string.h>
| #include <stdlib.h>
|
| int main(){
| int sock;
| struct sockaddr_un addr;
| char buf[4096];
| int pfds[2];
|
| pipe(pfds);
| sock=socket(PF_UNIX,SOCK_SEQPACKET,0);
| addr.sun_family=AF_UNIX;
| strcpy(addr.sun_path,"/tmp/foobar_testsock");
| bind(sock,(struct sockaddr *)&addr,sizeof(addr));
| listen(sock,1);
| if(fork()){
| close(sock);
| sock=socket(PF_UNIX,SOCK_SEQPACKET,0);
| connect(sock,(struct sockaddr *)&addr,sizeof(addr));
| fcntl(sock,F_SETFL,fcntl(sock,F_GETFL)|O_NONBLOCK);
| close(pfds[1]);
| read(pfds[0],buf,sizeof(buf));
| recv(sock,buf,sizeof(buf),0); // <-- this one
| }else accept(sock,NULL,NULL);
| exit(0);
| }
If you try it, make sure /tmp/foobar_testsock doesn't exist.
The marked recv() returns -1 (EAGAIN) on 2.6.23.9. Below you find a
patch that fixes that.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sungem's gem_reset_task() will unconditionally try to disable NAPI even
when it's called while the interface is not operating and hence the NAPI
struct isn't enabled. Make napi_disable() depend on gp->running.
Also removes a superfluous test of gp->running in the same function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to work around old LILO versions providing an invalid ss
register, the current setup code always sets up a new stack,
immediately following .bss and the heap. But this breaks LOADLIN.
This rewrite of the workaround checks for an invalid stack (ss!=ds)
first, and leaves ss:sp alone otherwise (apart from aligning esp).
[hpa note: LOADLIN has a number of arbitrary hard-coded limits that
are being pushed up against. Without some major revision of LOADLIN
itself it will not be sustainable keeping it alive. This gives it
another brief lease on life, however. This patch also helps the
cmdline truncation problem with old versions of SYSLINUX.]
Signed-off-by: Jens Rottmann <JRottmann at LiPPERT-AT. de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
sysfs: fix off-by-one error in fill_read_buffer()
kobject: two typo fixes
UIO: add UIO documentation target to DocBook Makefile
UIO: fix up the UIO documentation
create /sys/.../power when CONFIG_PM is set
allow LEGACY_PTYS to be set to 0
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
This was fixed using the following semantic patch.
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_pci_dev;
@@
T *d;
...
for_each_pci_dev(d)
{... when != pci_dev_put(d)
when != e = d
(
return d;
|
+ pci_dev_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pcie protdrv status can be returned uninitialized,
if there are no children under a device. This leads to
bad responses downstream. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some CPUs in the S3C24XX series do not support readback of the
value of a pin when the pin has been configured to an IRQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If another driver wants to claim the vbus pin, say
to notify the user of an connect/disconnect then allow
the IRQ to be shared by specifiying IRQ_SHARED in the
flags.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1018) adds an unusual_devs entry for the JetFlash
TS1GJF2A. This device doesn't like read requests for more than 188
sectors. Setting max_sectors down to 64 is overkill, but at least
it will work without errors.
For the torturous debugging history, see this thread:
http://marc.info/?t=118745764700005&r=1&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A recent patch added software synchronization during EHCI startup,
so ports aren't switched away from the companion controllers after
resets have started. This patch adds a short delay letting hardware
finish that port switching before any new resets begin ... so both
ends of that hardware race window are closed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dave Miller <davem@davemloft.net>
Cc: Dely Sy <dely.l.sy@intel.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
to make HAL like the microtek driver's devices the parent must be
correctly set.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1010) was written by both Kay Sievers and me. It solves
the problem of duplicated keys in USB uevent structures by refactoring
the uevent subroutines, taking advantage of the way the hotplug core
calls uevent handlers for the device's bus and for the device's type.
Keys needed for both USB-device and USB-interface events are added in
usb_uevent(), which is the bus handler. Keys appropriate only for
USB-device or USB-interface events are added in usb_dev_uevent() or
usb_if_uevent() respectively, the type handlers.
In addition, unnecessary tests for NULL pointers are removed as are
duplicated debugging log statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1009) solves the problem of multiple registrations for
USB sysfs files in a more satisfying way than the existing code. It
simply adds a flag to keep track of whether or not the files have been
created; that way the files can be created or removed as needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Arnd Bergmann wrote:
usb_hcd_flush_endpoint() has a retry loop that starts with a spin_lock_irq(),
but only gives up the spinlock, not the irq_disable before jumping to the
rescan label.
Alan Stern:
I agree with your sentiment, but it would be better to solve this
problem without using local_irq_disable().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Digging through old mail, I found a note about needing to remove the
separate entry for the USB HUB driver. It's not been separable from
usbcore (host side!) since quite early in the 2.4 kernel series.
And Johanness certainly isn't involved with it any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another one in the "ok, this is trivial to fix" list... :-)
[PATCH] fix directory references in usb/README
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Two main issues fixed here are:
- An improper use of in-struct lock to protect an open count
- Use of urb status for -EINPROGRESS
Also, along the way:
- Change usb_unlink_urb to usb_kill_urb. Apparently there's no need
to use usb_unlink_urb whatsoever in this driver, and the old use of
usb_kill_urb was outright racy (it unlinked and immediately freed).
- Fix indentation in adu_write. Looks like it was damaged by a script.
- Vitaly wants -EBUSY on multiply opens.
- bInterval was taken from a wrong endpoint.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Tested-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1014) was partly written by Tilman Schmidt. It
clarifies the USB power-management documentation by explaining that
when a disconnect occurs, a suspend method call might not be followed
by either a resume or a reset_resume call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This trivial documentation patch corrects a comment in usbdevice_fs.h; it
previously suggested that the signal would only be sent on error, but I am
told that it is sent on both successful and unsuccessful completion, and
that zero indicates that no signal should be sent.
Signed-off-by: Phil Endecott <spam_from_usb_devel@chezphil.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit acd2a847e7 usb_serial_generic_write()
disables interrupts when taking &port->lock which is also taken in
usb_serial_generic_read_bulk_callback() resulting in an inconsistent lock state
due to the latter not disabling interrupts on the local cpu. Fix that by
disabling interrupts in the latter call site also.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbled has a race where show methods for attributes in sysfs can
follow a NULL pointer during disconnect. The correct ordering fixes
it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1000) sets the SCSI allow_restart flag for USB disk
devices. In theory this should never hurt, and there definitely are
devices out there (such as the Seagate 250-GB external drive) which
need the flag to be set.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pl2303: add support for Corega CG-USBRS232R
This patch adds support for Corega CG-USBRS232R Serial Adapters.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes some build errors ... unclear how this got past earlier tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found that there is a off-by-one problem in the following code.
Version: 2.6.24-rc2
File: fs/sysfs/file.c:118-122
Function: fill_read_buffer
--------------------------------------------------------------------
count = ops->show(kobj, attr_sd->s_attr.attr, buffer->page);
sysfs_put_active_two(attr_sd);
BUG_ON(count > (ssize_t)PAGE_SIZE);
--------------------------------------------------------------------
Because according to the specification of the sysfs and the implement of
the show methods, the show methods return the number of bytes which would
be generated for the given input, excluding the trailing null.So if the
return value of the show methods equals PAGE_SIZE - 1, the buffer is full
in fact. And if the return value equals PAGE_SIZE, the resulting string
was already truncated,or buffer overflow occurred.
This patch fixes an off-by-one error in fill_read_buffer.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tejun Heo <teheo@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove references to the old uio_dummy demo module from UIO documentation.
Add a small paragraph to make it clearer that UIO is not a universal driver
interface.
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The CONFIG_SUSPEND changes in 2.6.23 caused a regression under certain
configuration conditions (SUSPEND=n, USB_AUTOSUSPEND=y) where all USB
device attributes in sysfs (idVendor, idProduct, ...) silently disappeared,
causing udev breakage and more.
The cause of this is that the /sys/.../power subdirectory is now only
created when CONFIG_PM_SLEEP is set, however, it should be created whenever
CONFIG_PM is set to handle the above situation. The following patch fixes
the regression.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The count of legacy pty devices can be set by a kernel commandline
parameter. For the distro kernel, we would like to disable all pty's
by default, but keep the opportunity to request devices on the kernel
commandline.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2.6.11 gave __GFP_ZERO's prep_zero_page a bogus "highmem may have to wait"
assertion. Presumably added under the misconception that clear_highpage
uses nonatomic kmap; but then and now it uses kmap_atomic, so no problem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tmpfs was misconverted to __GFP_ZERO in 2.6.11. There's an unusual case in
which shmem_getpage receives the page from its caller instead of allocating.
We must cover this case by clear_highpage before SetPageUptodate, as before.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: clean up kernel/sched_stat.h
sched: clean up overlong line in kernel/sched_debug.c
sched: clean up, move __sched_text_start/end to sched.h
sched: clean up sd_alloc_ctl_cpu_table() definition
softlockup: fix false positives on CONFIG_NOHZ
David Miller reported soft lockup false-positives that trigger
on NOHZ due to CPUs idling for more than 10 seconds.
The solution is touch the softlockup watchdog when we return from
idle. (by definition we are not 'locked up' when we were idle)
http://bugzilla.kernel.org/show_bug.cgi?id=9409
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ocfs2_truncate() and ocfs2_remove_inode_range() had reversed their "set
i_size" arguments to ocfs2_truncate_inline(). Fix things so that truncate
sets i_size, and punching a hole ignores it.
This exposed a problem where punching a hole in an inline-data file wasn't
updating the page cache, so fix that too.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The existing bug statement didn't take into account unhashed dentries which
might not have a cluster lock on them. This could happen if a node exporting
the file system via NFS is rebooted, re-exported to nfs clients and then
unmounted. It's fine in this case to not have a dentry cluster lock.
Just remove the bug statement and replace it with an error print, which
does the proper checks. Though we want to know if something has happened
which might have prevented a cluster lock from being created, it's
definitely not necessary to panic the machine for this.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Enable expensive bitmap scanning only if DEBUG option is enabled.
The bitmap scanning quite loads the CPU and on my machine the write
throughput of dd if=/dev/zero of=/ocfs2/file bs=1M count=500 conv=sync
improves from 37 MB/s to 45.4 MB/s in local mode...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
If the inode block isn't valid then we don't want to print the value from
that, instead print the block number which was passed in (which should
always be correct). Also, turn this into a debug print for now - folks who
hit an actual problem always have other logs indicating what the source is.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
It's almost never worth printing in that situation and we keep forgetting to
manually filter it out.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Right now we're just setting them from the existing parameters, not the
new ones that a remount specified.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
If a port goes down, ipoib_ib_dev_down() is invoked -- which flushes
the mcasts (clearing priv->broadcast) and clearing the path record
cache. If ipoib_start_xmit() is then invoked (before the broadcast
group is rejoined), a kernel oops results from attempting to access
priv->broadcast, which is still unset.
Returning NULL from path_rec_create() if priv->broadcast is NULL is a
harmless way of bypassing the problem -- the offending packet is
simply discarded "without prejudice."
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: SVM: Fix FPU leak while emulating clts
KVM: SVM: Unload guest fpu on vcpu_put()
KVM: x86 emulator: Use emulator_write_emulated and not emulator_write_std
KVM: x86 emulator: fix the saving of of the eip value
KVM: x86 emulator: fix JMP_REL
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add missing counter increment in iser_data_buf_aligned_len()
IB/ehca: Fix static rate regression
mlx4_core: Fix state check in mlx4_qp_modify()
IB/ipath: Normalize error return codes for posting work requests
IB/ipath: Fix offset returned to ibv_modify_srq()
IB/ipath: Fix error path in QP creation
IB/ipath: Fix offset returned to ibv_resize_cq()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: adds the context menu key (HUT GenDesc 0x84)
Input: add definitions for frame forward and frame back keys
Input: bf54x-keys - keypad does not exist on BF544 parts
Input: gpio-keys - request and configure GPIOs
Input: i8042 - add i8042.noloop quirk for MS Virtual Machine
Sonypi: use synchronize_irq instead of sycnronize_sched
sonypi: fit input devices into sysfs tree
sony-laptop: fit input devices into sysfs tree
these utilities implemented in lib/hexdump.c are more handy, please use this.
Bart:
- s/KERN_DEBUG/KERN_CONT/ as pointed out by Randy
- s/DUMP_PREFIX_OFFSET/DUMP_PREFIX_NONE/
- don't include ASCII dump
- respect 80-columns limit
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/pci/amd74xx.c: In function `init_hwif_amd74xx':
drivers/ide/pci/amd74xx.c:387: error: implicit declaration of function `pci_get_legacy_ide_irq'
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't override ide_register_hw() result and check if there is a hwif
available to use.
* MAX_HWIFS is user configurable nowadays so replace it by hard-coded value.
* Remove the comment about ide_hwifs[].
Acked-by: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ETRAX_IDE and friends from arch/cris/arch-{v10,v32}/drivers/Kconfig
to drivers/ide/Kconfig.
* Don't force selecting ide-disk and ide-cd device drivers
(please handle this through defconfig if necessary).
* Make ETRAX_IDE depend on BROKEN for the time being
(it doesn't even compile currently).
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add a separate config option for ide-8300 host driver instead of depending
on CONFIG_H8300.
This change is a preparation for the future changes and also allows ide-h8300
to be disabled if needed.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Only LWMON, IVMS8, IVML24 and TQM8xxL platforms have the needed
defines (IDE0_BASE_OFFSET and friends) in the platform header file.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add pci_enable_device() to aec62xx probe function
before doing any I/O.
Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR
is 0 and the following inb() causes a kernel oops.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).
If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.
The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.
Bart: minor cleanups
Signed-off-by: Jonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Update sys_rt_sigsuspend() of arch/m32r/signal.c.
This modification is derived from generic one of kernel/signal.c.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
checksyscalls.sh reports warnings for missing syscalls.
But, on m32r, some legacy syscalls were removed elaborately.
This patch kills warnings for obsolete syscalls, which are
no longer used in the m32r kernel.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
The clts code didn't use set_cr0 properly, so our lazy FPU
processing wasn't being done by the clts instruction at all.
(this isn't called on Intel as the hardware does the decode for us)
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
emulator_write_std() is not implemented, and calling write_emulated should
work just as well in place of write_std.
Fixes emulator failures with the push r/m instruction.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
this make sure that no matter what is the operand size,
all the value of the eip will be saved
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Change JMP_REL to call to register_address_increment(): the operands size
should not effect the calculation of the eip, instead the ad_bytes should
affect it.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add more safeguards to protect against misinterpreting a chain entry
as a normal scatterlist and vice-versa.
* Make sure the entry isn't a chain when assigning and reading a
normal sg.
* Clear offset and length when chaining.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This was a temporary debugging thing for sg chaining testing, revert
it now as it has served its purpose.
This reverts commit 563063a808.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mmc_init_queue only initializes the scatterlists with sg_init_table()
when using a bounce buffer. This leads to a BUG() when CONFIG_DEBUG_SG
is set.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix a memory leak in alloc_disk_node(). Don't forget to free 'dkstats' when the allocation of 'part' failed.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
if blktrace program segfault it will not be able
to call BLKTRACETEARDOWN. Now if we run the blktrace
again that would result in a failure to create the
block/<device> debugfs directory.This will result
in blk_remove_root() to be called which will set
blk_tree_root to NULL. But the debugfs block dir
still exist because it contain subdirectory.
Now if we try to fix it using BLKTRACETEARDOWN
it won't work because blk_tree_root is NULL.
Fix the same.
Tested as below
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
Segmentation fault
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
BLKTRACESETUP: No such file or directory
Failed to start trace on /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -k /dev/hdc
root@qemu-image:/home/kvaneesh/blktrace# ./blktrace -d /dev/hdc
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (41 commits)
[XFRM]: Fix leak of expired xfrm_states
[ATM]: [he] initialize lock and tasklet earlier
[IPV4]: Remove bogus ifdef mess in arp_process
[SKBUFF]: Free old skb properly in skb_morph
[IPV4]: Fix memory leak in inet_hashtables.h when NUMA is on
[IPSEC]: Temporarily remove locks around copying of non-atomic fields
[TCP] MTUprobe: Cleanup send queue check (no need to loop)
[TCP]: MTUprobe: receiver window & data available checks fixed
[MAINTAINERS]: tlan list is subscribers-only
[SUNRPC]: Remove SPIN_LOCK_UNLOCKED
[SUNRPC]: Make xprtsock.c:xs_setup_{udp,tcp}() static
[PFKEY]: Sending an SADB_GET responds with an SADB_GET
[IRDA]: Compilation for CONFIG_INET=n case
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
[ARP]: Fix arp reply when sender ip 0
[IPV6] TCPMD5: Fix deleting key operation.
[IPV6] TCPMD5: Check return value of tcp_alloc_md5sig_pool().
[IPV4] TCPMD5: Use memmove() instead of memcpy() because we have overlaps.
[IPV4] TCPMD5: Omit redundant NULL check for kfree() argument.
ieee80211: Stop net_ratelimit/IEEE80211_DEBUG_DROP log pollution
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] api: Fix potential race in crypto_remove_spawn
[CRYPTO] authenc: Move initialisations up to shut up gcc
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFS: Clean up new multi-segment direct I/O changes
NFS: Ensure we return zero if applications attempt to write zero bytes
NFS: Support multiple segment iovecs in the NFS direct I/O path
NFS: Introduce iovec I/O helpers to fs/nfs/direct.c
SUNRPC: Add missing "space" to net/sunrpc/auth_gss.c
SUNRPC: make sunrpc/xprtsock.c:xs_setup_{udp,tcp}() static
NFS: fs/nfs/dir.c should #include "internal.h"
NFS: make nfs_wb_page_priority() static
NFS: mount failure causes bad page state
SUNRPC: remove NFS/RDMA client's binary sysctls
kernel BUG at fs/nfs/namespace.c:108! - can be triggered by bad server
sunrpc: rpc_pipe_poll may miss available data in some cases
sunrpc: return error if unsupported enctype or cksumtype is encountered
sunrpc: gss_pipe_downcall(), don't assume all errors are transient
NFS: Fix the ustat() regression
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (56 commits)
Blackfin arch: fix bug when enable uart1 with uart0 disabled => no initial console
Blackfin arch: split apart dump_bfin_regs and merge/remove show_regs from process.c, which was largely duplicated
Blackfin arch: use common __INIT/__FINIT defines rather than setting the .section ourselves to .init.text
Blackfin arch: fix bug when sending signals with the wrong PC, cause gdb get confused
Blackfin arch: Ensure we printk out strings with the proper loglevel
Blackfin arch: Need to specify ax with the .init.text section,
Blackfin arch: Update Kconfig to latest Blackfin silicon datasheets
Blackfin arch: update defconfig files
Blackfin arch: Fix typo, and add ENDPROC - no functional changes
Blackfin arch: convert READY to DMA_READY as it causes build errors in common sound code otherwise
Blackfin arch: add defines for the on-chip L1 ROM of BF54x
Blackfin arch: cplb and map header file cleanup
Blackfin arch: cleanup the cplb declares
Blackfin arch: fix broken on BF52x, remove silly checks on processors for L1_SCRATCH defines
Blackfin arch: add support for working around anomaly 05000312
Blackfin arch: cleanup BF54x header file and add BF547 definition
Blackfin arch: fix building for BF542 processors which only have 1 TWI
Blackfin arch: rename _return_from_exception to _bfin_return_from_exception and export it
Blackfin arch: move EXPORT_SYMBOL() to C files where the symbol is actually defined
Blackfin arch: fix bug NOR Flash MTD mount fail
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: include ax88796 in the defconfig for r7785rp
sh: include ax88796 in the defconfig for r7780mp
sh: fix R2D-1 CF support
fb: Orphan imsttfb.
sh: Update mailing list info.
sh: lockless UTLB miss fast-path.
sh: Kill off UTLB flush in fast-path.
sh: Fix copy_{to,from}_user_page() with cache disabled.
Plip passes a string "name" that is allocated on stack to
parport_register_device. parport_register_device holds the pointer to
"name" and when the registering function exits, it points nowhere.
On some machine, this bug causes bad names to appear in /proc, such as
/proc/sys/dev/parport/parport0/devices/T^/�X^/�, on others, the plip
proc node is completely missing.
The patch also fixes documentation to note this requirement.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd. For calling from outside interrupts, netif_rx_ni exists.
This fixes plip to use netif_rx_ni. It fixes the infamous error "NOHZ:
local_softirq_panding 08" that happens on some machines with NOHZ and
plip --- it is caused by the fact that softirq is pending and ksoftirqd
is sleeping.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: Avoid re-using minor numbers before the original device is closed.
tifm_sd: handle non-power-of-2 block sizes
mmc_block: check card state after write
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix check after use error in ACL code
[CIFS] Fix potential data corruption when writing out cached dirty pages
[CIFS] Fix spurious reconnect on 2nd peek from read of SMB length
[CIFS] remove build warning
[CIFS] Have CIFS_SessSetup build correct SPNEGO SessionSetup request
[CIFS] minor checkpatch cleanup
[CIFS] have cifs_get_spnego_key get the hostname from TCP_Server_Info
[CIFS] add hostname field to TCP_Server_Info struct
[CIFS] clean up error handling in cifs_mount
[CIFS] add ver= prefix to upcall format version
[CIFS] Fix buffer overflow if server sends corrupt response to small
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: bump transfer chunk size if it's odd
libata: Return proper ATA INT status in pata_bf54x driver
pata_ali: trim trailing whitespace (fix checkpatch complaints)
pata_isapnp: Polled devices
pata_hpt37x: Fix cable detect bug spotted by Sergei
pata_ali: Lots of problems still showing up with small ATAPI DMA
pata_ali: Add Mitac 8317 and derivatives
libata-core: List more documentation sources for reference
ata_piix: Invalid use of writel/readl with iomap
sata_sil24: fix sg table sizing
pata_jmicron: fix disabled port handling in jmicron_pre_reset()
pata_sil680: kill bogus reset code (take 2)
ata_piix: port enable for the first SATA controller of ICH8 is 0xf not 0x3
ata_piix: only enable the first port on apple macbook pro
ata_piix: reorganize controller IDs
pata_sis.c: Add Packard Bell EasyNote K5305 to laptops
libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
libata: use ATA_HORKAGE_STUCK_ERR for ATAPI tape drives
libata: workaround DRQ=1 ERR=1 for ATAPI tape drives
libata: remove unused functions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: fix net driver loop case where we fail to restart
module: fix and elaborate comments
virtio: fix module/device unloading
lguest: Fix uninitialized members in example launcher
The xfrm_timer calls __xfrm_state_delete, which drops the final reference
manually without triggering destruction of the state. Change it to use
xfrm_state_put to add the state to the gc list when we're dropping the
last reference. The timer function may still continue to use the state
safely since the final destruction does a del_timer_sync().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (39 commits)
ACPI: EC: Workaround for optimized controllers (version 3)
ACPI: EC: use printk_ratelimit(), add some DEBUG mode messages
Revert "ACPI: EC: Workaround for optimized controllers"
ACPI: fix two IRQ8 issues in IOAPIC mode
ACPI: Add missing spaces to printk format
cpuidle: fix HP nx6125 regression
cpuidle: add sched_clock_idle_[sleep|wakeup]_event() hooks
cpuidle: fix C3 for no bus-master control case
ACPI: thinkpad-acpi: fix oops when a module parameter has no value
Revert "Fix very high interrupt rate for IRQ8 (rtc) unless pnpacpi=off"
ACPI: EC: Don't init EC early if it has no _INI
Revert "acpi: make ACPI_PROCFS default to y"
Revert "ACPI: add documentation for deprecated /proc/acpi/battery in ACPI_PROCFS"
ACPI: Split out control for /proc/acpi entries from battery, ac, and sbs.
ACPI: Video: Increase buffer size for writes to brightness proc file.
ACPI: EC: Workaround for optimized controllers
ACPI: SBS: Fix retval warning
ACPI: Enable MSR (FixedHW) support for T-States
ACPI: Get throttling info from BIOS only after evaluating _PDC
ACPI: Use _TSS for throttling control, when present. Add error checks.
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] vpe: Add missing "space"
[MIPS] Compliment va_start() with va_end().
[MIPS] IP22: Fix broken eeprom access by using __raw_readl/__raw_writel
[MIPS] IP22: Fix broken EISA interrupt setup by switching to generic i8259
[MIPS] 64-bit Sibyte kernels need DMA32.
[MIPS] Only build r4k clocksource for systems that work ok with it.
[MIPS] Handle R4000/R4400 mfc0 from count register.
[MIPS] Fix possible hang in LL/SC futex loops.
[MIPS] Fix context DSP context / TLS pointer switching bug for new threads.
[MIPS] IP32: More interrupt renumbering fixes.
[MIPS] time: MIPSsim's plat_time_init doesn't need to be irq safe.
[MIPS] time: Fix negated condition in cevt-r4k driver.
[MIPS] Fix pcspeaker build.
if you are lucky (unlucky?) enough to have shared interrupts, the
interrupt handler can be called before the tasklet and lock are ready
for use.
Signed-off-by: chas williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For a kernel built with "make ARCH=x86" the following system
information is displayed when running the new kernel
$ uname -m
x86
On some i386 systems (e.g. K7) we even have the following information
$ uname -m
x66
This is weird. The usual information for "uname -m" should be "x86_64"
on 64-bit and "i386" or "i686" on 32-bit.
This patch fixes the issue by setting UTS_MACHINE to "i386" for 32-bit
kernel builds and to "x86_64" for 64-bit kernel builds. I.e., "x86"
won't be used for UTS_MACHINE anymore.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify calling sequence of nfs_direct_{read,write}_schedule(), and
rename them to reflect their new role.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add helpers that iterate over multi-segment iovecs. These will
be used to support multi-segment scatter/gather direct I/O in a
later patch.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
While testing a kernel based upon ecd744eec3
(with wrong boot arguments), I got the following bad page state entry while
NFS was trying to mount it's rootfs:
IP-Config: Complete:
device=eth0, addr=192.168.1.101, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.1.101, domain=, nis-domain=(none),
bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.100
rpcbind: server 192.168.1.100 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.100
rpcbind: server 192.168.1.100 not responding, timed out
Root-NFS: Unable to get mountd port number from server, using default
mount: server 192.168.1.100 not responding, timed out
Root-NFS: Server returned error -5 while mounting /nfs/rootfs/
VFS: Unable to mount root fs via NFS, trying floppy.
Bad page state in process 'swapper'
page:c02b1260 flags:0x00000400 mapping:00000000 mapcount:0 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
[<c0023e34>] (dump_stack+0x0/0x14) from [<c0062570>] (bad_page+0x70/0xac)
[<c0062500>] (bad_page+0x0/0xac) from [<c0064914>] (free_hot_cold_page+0x80/0x178)
[<c0064894>] (free_hot_cold_page+0x0/0x178) from [<c0064a74>] (free_hot_page+0x14/0x18)
[<c0064a60>] (free_hot_page+0x0/0x18) from [<c0067078>] (put_page+0xf8/0x154)
[<c0066f80>] (put_page+0x0/0x154) from [<c007dbc8>] (kfree+0xc8/0xd0)
[<c007db00>] (kfree+0x0/0xd0) from [<c00cbb54>] (nfs_get_sb+0x230/0x710)
[<c00cb924>] (nfs_get_sb+0x0/0x710) from [<c0084334>] (vfs_kern_mount+0x58/0xac)[<c00842dc>] (vfs_kern_mount+0x0/0xac) from [<c00843c0>] (do_kern_mount+0x38/0xf4)
[<c0084388>] (do_kern_mount+0x0/0xf4) from [<c0099c7c>] (do_mount+0x1e8/0x614)
...
This seems to be caused by use of an uninitialised structure due to NULL
options being passed to nfs_validate_mount_data(). Ensure that the
parsed mount data is always initialised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(Trond: added fix for the same bug in nfs4_validate_mount_data()).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Support for binary sysctls is being deprecated in 2.6.24. Since there
are no applications using the NFS/RDMA client's binary sysctls, it
makes sense to remove them. The patch below does this while leaving
the /proc/sys interface unchanged.
Please consider this for 2.6.24.
Signed-off-by: James Lentini <jlentini@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
increase the default minimum granularity some more - this gives us
more performance in aim7 benchmarks.
also correct some comments: we scale with ilog(ncpus) + 1.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Devan Lippman noticed that the RLIMIT_CPU comment in resource.h is
incorrect: the field is in seconds, not msecs. We used msecs in
earlier versions of the patch but that got changed.
Found-by: Devan Lippman <devan.lippman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Srivatsa Vaddagiri noticed occasionally incorrect CPU usage
values in top and tracked it down to stime going below 0 in
task_stime(). Negative values are possible there due to the
sampled nature of stime/utime.
Fix suggested by Balbir Singh.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <balbir@linux.vnet.ibm.com>
The commit
commit 5cb350baf5
Author: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Date: Mon Oct 15 17:00:14 2007 +0200
sched: group scheduling, sysfs tunables
introduced the uids_mutex and the helpers to lock/unlock it.
Unfortunately, the error paths of alloc_uid() were not patched
to unlock it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ARM __kuser_cmpxchg routine is meant to implement an atomic cmpxchg
in user space. It however can produce spurious false negative if a
processor exception occurs in the middle of the operation. Normally
this is not a problem since cmpxchg is typically called in a loop until
it succeeds to implement an atomic increment for example.
Some use cases which don't involve a loop require that the operation be
100% reliable though. This patch changes the implementation so to
reattempt the operation after an exception has occurred in the critical
section rather than abort it.
Here's a simple program to test the fix (don't use CONFIG_NO_HZ in your
kernel as this depends on a sufficiently high interrupt rate):
#include <stdio.h>
typedef int (__kernel_cmpxchg_t)(int oldval, int newval, int *ptr);
#define __kernel_cmpxchg (*(__kernel_cmpxchg_t *)0xffff0fc0)
int main()
{
int i, x = 0;
for (i = 0; i < 100000000; i++) {
int v = x;
if (__kernel_cmpxchg(v, v+1, &x))
printf("failed at %d: %d vs %d\n", i, v, x);
}
printf("done with %d vs %d\n", i, x);
return 0;
}
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The lock is acquired with spin_lock_irqsave() and released in the
not-found case with spin_unlock_irqrestore().
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AITC code did not allow to start kernel, if bootloader
manipulates with interrupt level mask. The change ensures,
that NIMASK is initialized into correct state and that
interrupts enable registers are cleared.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
warmbloodedcreature@gmail.com reported that an APIC-enabled
Asus a7v8x-x with an Athlon XP reboots early in the bootup:
http://bugzilla.kernel.org/show_bug.cgi?id=8723
after a long marathon of spontaneous-reboot debugging, it turns
out to be caused by sync_Arb_ids(). AMD CPUs never really needed
this sequence anyway, so just return early if we meet an AMD CPU.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Michael Kerrisk reported that a long standing bug in the adjtimex()
system call causes glibc's adjtime(3) function to deliver the wrong
results if 'delta' is NULL.
add the ADJ_OFFSET_SS_READ API detail, which will be used by glibc
to fix this API compatibility bug.
Also see: http://bugzilla.kernel.org/show_bug.cgi?id=6761
[ mingo@elte.hu: added patch description and made it backwards compatible ]
NOTE: the new flag is defined 0xa001 so that it returns -EINVAL on
older kernels - this way glibc can use it safely. Suggested by Ulrich
Drepper.
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix:
arch/x86/kernel/kprobes_64.c: In function 'set_current_kprobe':
arch/x86/kernel/kprobes_64.c:152: sorry, unimplemented: inlining failed in call to 'is_IF_modifier': recursive inlining
arch/x86/kernel/kprobes_64.c:166: sorry, unimplemented: called from here
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: mingo@elte.hu
Cc: akpm@linux-foundation.org
Cc: tglx@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
HP ProLiant systems DL385 G2 and DL585 G2 need pci=bfsort to enumerate PCI
devices in the expected order.
Matt sayeth:
biosdevname is a userspace app I wrote to help solve this so we don't need
to patch the kernel for future systems. It's not integrated into any
distributions properly yet, but is included in openSUSE 10.3 and Fedora 8
for people who want to download and install it there. It acts as a udev
helper.
For the time being, patching the kernel is necessary. I really hope
biosdevname eliminates that need in future distributions.
http://linux.dell.com/biosdevname/
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Cc: mingo@elte.hu
Cc: andy@greyhouse.net
Cc: john.cagle@hp.com
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: correctly set UTS_MACHINE for "make ARCH=x86"
For a kernel built with "make ARCH=x86" the following system
information is displayed when running the new kernel
$ uname -m
x86
On some i386 systems (e.g. K7) we even have the following information
$ uname -m
x66
This is weird. The usual information for "uname -m" should be "x86_64"
on 64-bit and "i386" or "i686" on 32-bit.
This patch fixes the issue by setting UTS_MACHINE to "i386" for 32-bit
kernel builds and to "x86_64" for 64-bit kernel builds. I.e., "x86"
won't be used for UTS_MACHINE anymore.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Herrmann <aherrman@arcor.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@redhat.com>
ACPI processor idle code references local_apic_timer_c2_ok, which
is not available when LOCAL_APIC is disabled.
Define local_apic_timer_c2_ok as a constant, when LOCAL_APIC=n
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
today, all oopses contain a version number of the kernel, which is nice
because the people who actually do bother to read the oops get this
vital bit of information always without having to ask the reporter in
another round trip.
However, WARN_ON() and many other dump_stack() users right now lack this
information; the patch below adds this. This information is essential
for getting people to use their time effectively when looking at these
things; in addition, it's essential for tools that try to collect
statistics about defects.
Please consider, since its so simple and important for long term kernel
quality processes.
The code is identical between 32/64 bit; a lot of this code should be
unified over time, the patch keeps the identical-ness intact.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
AMD Opteron processors before CG revision don't like C-states > 1.
This solves the long standing bugzilla #5303 and probably some more
on affected machines:
http://bugzilla.kernel.org/show_bug.cgi?id=5303
[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
More than 3 years ago Niclas Gustafsson reported a 'stopped time'
problem:
> Watching the /proc/interrupts with 10s apart after the "stop".
>
> [root@s151 root]# more /proc/interrupts
> CPU0
> 0: 66413955 local-APIC-edge timer
[...]
> LOC: 67355837
> ERR: 0
> MIS: 0
> [root@s151 root]# more /proc/interrupts
> CPU0
> 0: 66413955 local-APIC-edge timer
[...]
> LOC: 67379568
> ERR: 0
> MIS: 0
This may be because buggy SMM firmware messes with the 8259A (configured
for a transparent mode -- yes that rare "local-APIC-edge" mode is tricky
;-) ) insanely.
this should resolve:
http://bugzilla.kernel.org/show_bug.cgi?id=2544http://bugzilla.kernel.org/show_bug.cgi?id=6296
Patch-dusted-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The incorrect GPIO pins are being initialized for the buttons on the
Atmel AT91SAM9261-EK board. This buggy configuration turns LCD screen
blue...
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91 I2C driver is currently marked as "broken" due to hardware
issues. This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.
This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).
Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The calculation for the Master clock divisor (MDIV) is different on the
SAM9 processors than on the AT91RM9200.
Orignal patch from Sascha Erlacher.
Also use the defined AT91_PMC_PRES instead of hard-coded bitmasks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sibyte SOCs only have 32-bit PCI. Due to the sparse use of the address
space only the first 1GB of memory is mapped at physical addresses
below 1GB. If a system has more than 1GB of memory 32-bit DMA will
not be able to reach all of it.
For now this patch is good enough to keep Sibyte users happy but it seems
eventually something like swiotlb will be needed for Sibyte.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The R4000 and R4400 have an errata where if the cp0 count register is read
in the exact moment when it matches the compare register no interrupt will
be generated.
This bug may be triggered if the cp0 count register is being used as
clocksource and the compare interrupt as clockevent. So a simple
workaround is to avoid using the compare for both facilities on the
affected CPUs.
This is different from the workaround suggested in the old errata documents;
at some opportunity probably the official version should be implemented
and tested. Another thing to find out is which processor versions
exactly are affected. I only have errata documents upto R4400 V3.0
available so for the moment the code treats all R4000 and R4400 as broken.
This is potencially a problem for some machines that have no other decent
clocksource available; this workaround will cause them to fall back to
another clocksource, worst case the "jiffies" source.
The LL / SC loops in __futex_atomic_op() have the usual fixups necessary
for memory acccesses to userspace from kernel space installed:
__asm__ __volatile__(
" .set push \n"
" .set noat \n"
" .set mips3 \n"
"1: ll %1, %4 # __futex_atomic_op \n"
" .set mips0 \n"
" " insn " \n"
" .set mips3 \n"
"2: sc $1, %2 \n"
" beqz $1, 1b \n"
__WEAK_LLSC_MB
"3: \n"
" .set pop \n"
" .set mips0 \n"
" .section .fixup,\"ax\" \n"
"4: li %0, %6 \n"
" j 2b \n" <-----
" .previous \n"
" .section __ex_table,\"a\" \n"
" "__UA_ADDR "\t1b, 4b \n"
" "__UA_ADDR "\t2b, 4b \n"
" .previous \n"
: "=r" (ret), "=&r" (oldval), "=R" (*uaddr)
: "0" (0), "R" (*uaddr), "Jr" (oparg), "i" (-EFAULT)
: "memory");
The branch at the end of the fixup code, it goes back to the SC
instruction, no matter if the fault was first taken by the LL or SC
instruction resulting in an endless loop which will only terminate if
the address become valid again due to another thread setting up an
accessible mapping and the CPU happens to execute the SC instruction
successfully which due to the preceeding ERET instruction of the fault
handler would only happen if UNPREDICTABLE instruction behaviour of the
SC instruction without a preceeding LL happens to favor that outcome.
But normally processes are nice, pass valid arguments and we were just
getting away with this.
Thanks to Kaz Kylheku <kaz@zeugmasystems.com> for providing the original
report and a test case.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A new born thread starts execution not in schedule but rather in
ret_from_fork which results in it bypassing the part of the code to
load a new context written in C which are the DSP context and the
userlocal register which Linux uses for the TLS pointer. Frequently
we were just getting away with this bug for a number of reasons:
o Real world application scenarios are very unlikely to use clone or fork
in blocks of DSP code.
o Linux by default runs the child process right after the fork, so the
child by luck will find all the right context in the DSP and userlocal
registers.
o So far the rdhwr instruction was emulated on all hardware so userlocal
wasn't getting referenced at all and the emulation wasn't suffering
from the issue since it gets it's value straight from the thread's
thread_info.
Fixed by moving the code to load the context from switch_to() to
finish_arch_switch which will be called by newborn and old threads.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
None of the drives I have follows what the standard says about
transfer chunk size. Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.
According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended. However, in reality, none of the
drives I have does that. They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.
In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA. Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes. This causes data corruption and buffer
overruns.
This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte. This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The #ifdef's in arp_process() were not only a mess, they were also wrong
in the CONFIG_NET_ETHERNET=n and (CONFIG_NETDEV_1000=y or
CONFIG_NETDEV_10000=y) cases.
Since they are not required this patch removes them.
Also removed are some #ifdef's around #include's that caused compile
errors after this change.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The skb_morph function only freed the data part of the dst skb, but leaked
the auxiliary data such as the netfilter fields. This patch fixes this by
moving the relevant parts from __kfree_skb to skb_release_all and calling
it in skb_morph.
It also makes kfree_skbmem static since it's no longer called anywhere else
and it now no longer does skb_release_data.
Thanks to Yasuyuki KOZAKAI for finding this problem and posting a patch for
it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. update default MFPR value to drive strength fast 3mA and edge
detection logic disabled
2. update impacted MFP_CFG_xxx() macros
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
x = vmalloc(...);
else
#endif
x = kmalloc(...);
Unlike it, the inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
vfree(x);
else
#else
kfree(x);
#endif
The error is obvious - if the NUMA is on and the size
is less than the PAGE_SIZE we leak the pointer (kfree is
inside the #else branch).
Compiler doesn't warn us because after the kfree(x) there's
a "x = NULL" assignment, so here's another (minor?) bug: we
don't set x to NULL under certain circumstances.
Boring explanation, I know... Patch explains it better.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The change 050f009e16
[IPSEC]: Lock state when copying non-atomic fields to user-space
caused a regression.
Ingo Molnar reports that it causes a potential dead-lock found by the
lock validator as it tries to take x->lock within xfrm_state_lock while
numerous other sites take the locks in opposite order.
For 2.6.24, the best fix is to simply remove the added locks as that puts
us back in the same state as we've been in for years. For later kernels
a proper fix would be to reverse the locking order for every xfrm state
user such that if x->lock is taken together with xfrm_state_lock then
it is to be taken within it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* Always pass the same value to free_irq() that we pass to
request_irq(). This fixes several bugs.
* Always call NCR5380_intr() with 'irq' and 'dev_id' arguments.
Note, scsi_falcon_intr() is the only case now where dev_id is not the
scsi_host.
* Always pass Scsi_Host to request_irq(). For most cases, the drivers
already did so, and I merely neated the source code line. In other
cases, either NULL or a non-sensical value was passed, verified to be
unused, then changed to be Scsi_Host in anticipation of the future.
In addition to the bugs fixes, this change makes the interface usage
consistent, which in turn enables the possibility of directly
referencing Scsi_Host from all NCR5380_intr() invocations.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While adding sg chaining support to iSER, a "for" loop was replaced
with a "for_each_sg" loop. The "for" loop included the incrementation
of 2 variables. Only one of them is incremented in the current
"for_each_sg" loop. This caused iSER to think that all data is
unaligned, and all data was copied to aligned buffers.
This patch increments the missing counter inside the "for_each_sg"
loop whenever necessary.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Accidently I reversed the order of pci_save_state and
pci_set_power_state in .suspend()/.resume() callbacks
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
smc911x_set_multicast_list fails to fill out the multicast hash table
correctly; Bit 1 was used rather than bit 5 to decide if the lower or
upper register should be used.
The function is at the same time cleaned up by calling ether_crc rather
than using it's own bit reversal table.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell Yukon XL chipset appears to have a hardware glitch
where it will repeat the checksum of the last packet. Of course, this is
timing sensitive and only happens sometimes...
More info: http://bugzilla.kernel.org/show_bug.cgi?id=9381
As a workaround just disable hardware checksumming by default on
this chip version. The earlier workaround for PCIX, dual port
was also on Yukon XL so don't need to disable checksumming there.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent driver from brawly logging packet checksum errors.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using own tx_packets counter instead of firmware counters.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x_local pointer in smc911x_rcv is only used in the SMC_USE_DMA
case. Move it under the #ifdef so GCC doesn't generate a warning in the
non-DMA case.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
elif defined(CONFIG_*) should be used instead of elif CONFIG_*
so GCC doesn't give warnings about undefined symbols when the config
option is disabled.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The amd8111e network driver was broken by
bea3348eef, which makes the driver
call napi_enable() and napi_disable() even if the driver had been
configured without CONFIG_AMD8111E_NAPI, and thus
netif_napi_add() had not been called on initialization.
This triggers a BUG in napi_enable().
This patch fixes the problem. Please apply.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A printk in the error handling code of dm9601.c was missing a newline.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems. This patch
updates sg table sizing such that
* One full page is used for PRB + sg table. On 4k page,
this results in 253 sg's.
* Make ATAPI sg block properly sized.
* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are two bugs in disabled port handling.
* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0
The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0. The net result is that cable
is always left at ATA_CBL_UNKNOWN. This results in false 80c
configuration and thus transfer errors.
This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As it is crypto_remove_spawn may try to unregister an instance which is
yet to be registered. This patch fixes this by checking whether the
instance has been registered before attempting to remove it.
It also removes a bogus cra_destroy check in crypto_register_instance as
1) it's outside the mutex;
2) we have a check in __crypto_register_alg already.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It seems that newer versions of gcc have regressed in their abilities to
analyse initialisations. This patch moves the initialisations up to avoid
the warnings.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The original code has striking complexity to perform a query
which can be reduced to a very simple compare.
FIN seqno may be included to write_seq but it should not make
any significant difference here compared to skb->len which was
used previously. One won't end up there with SYN still queued.
Use of write_seq check guarantees that there's a valid skb in
send_head so I removed the extra check.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: John Heffner <jheffner@psc.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It seems that the checked range for receiver window check should
begin from the first rather than from the last skb that is going
to be included to the probe. And that can be achieved without
reference to skbs at all, snd_nxt and write_seq provides the
correct seqno already. Plus, it SHOULD account packets that are
necessary to trigger fast retransmit [RFC4821].
Location of snd_wnd < probe_size/size_needed check is bogus
because it will cause the other if() match as well (due to
snd_nxt >= snd_una invariant).
Removed dead obvious comment.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the ax88796 device driver to the r7785rp defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ax88796 device driver to the r7780mp defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes CF support for R2D-1 boards. Both R2D-1 and
R2D-PLUS are equipped with CF IRQs, but the R2D-1 FPGA version
seem to deliver IRQ spikes with certain CF cards during libata
probing. This patch enables polling for R2D-1 as a workaround
for this broken FGPA logic.
R2D-1 CF support was recently introduced by commit:
43f4b8c757.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Your mail to 'Tlan-devel' with the subject
drivers/net/tlan question
Is being held until the list moderator can review it for approval.
The reason it is being held:
Post by non-member to a members-only list
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Found this occasionally.
The CONFIG_INET=n is hardly ever set, but if it is the
irlan_eth_send_gratuitous_arp() compilation should produce a
warning about unused variable in_dev.
Too pedantic? :)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, gpio_keys.c assumes the GPIOs to be already properly configured;
this patch changes gpio-keys to perform explicit calls to gpio_request() and
gpio_configure_input().
This matches the behaviour of leds-gpio.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When booting under Microsoft Virtual Machine, the noloop quirk is
needed, otherwise PS/2 mouse is not properly detected.
Reported-by: Lawrence Steeger <vendor@russte.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We know exactly what IRQ we are using, so synchronize_irq()
suits much better. Plus synchronize_sched() will not work
for us in -rt kernels.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Properly set up parent on input devices registered by sonypi.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Properly set up parent on input devices registered by sony-laptop.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Mattia Dongili <malattia@linux.it>
Move the code which marks the minor number as free to mmc_blk_put() so
that it happens on the final close() (or removal), instead of doing it
at removal even when the device is still logically open.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is possible to handle arbitrary block sizes with tifm card reader by
conditionally switching to PIO in case such block has to be delivered. At
the beginning of each request, DMA is either disabled (non-power-of-2 block
size) or set to load time user preference.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards have been reported to signal that they're ready prematurely.
Checking both the busy bit and card state solves the issue.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We need to send signals with the proper PC, or gdb gets
confused, and lots of tests fail. This should fix that.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- remove duplicated defines for the BF561
- generalize L2 support (so that it works for BF54x) and mark it executable
- add support for reading/executing the Boot ROM sections
(since it has data/functions we may need at runtime)
- and fixup names for each map
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- no need to declare their sizes in the common header
- no need to tack on the section attribute as only the definition matters, not references
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Anomaly 05000312 - Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted:
DESCRIPTION:
When instruction cache is enabled, erroneous behavior may occur when any of the following instructions are interrupted:
. CSYNC
• SSYNC
• LCx =
• LTx = (only when LCx is non-zero)
• LBx = (only when LCx is non-zero)
When this problem occurs, a variety of incorrect things could happen, including an illegal instruction exception. Additional errors could
show up as an exception, a hardware error, or an instruction that is valid but different than the one that was expected.
WORKAROUND:
Place a cli before all SSYNC, CSYNC, "LCx =", "LTx =", and "LBx =" instructions to disable interrupts, and place an sti after each of these
instructions to re-enable interrupts. When these instructions are executed in code that is already non-interruptible, the problem will not
occur.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The APM emulation is currently broken as a result of commit
8314418629
"Freezer: make kernel threads nonfreezable by default"
that removed the PF_NOFREEZE annotations from apm_ioctl() without adding
the appropriate freezer hooks. Fix it and remove the unnecessary variable flags
from apm_ioctl().
Special thanks to Franck Bui-Huu <vagabon.xyz@gmail.com> for pointing out the
problem.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Len Brown <len.brown@intel.com>
This is silly, but I have turned the CONFIG_IP_VS to m,
to check the compilation of one (recently sent) fix
and set all the CONFIG_IP_VS_PROTO_XXX options to n to
speed up the compilation.
In this configuration the compiler warns me about
CC [M] net/ipv4/ipvs/ip_vs_proto.o
net/ipv4/ipvs/ip_vs_proto.c:49: warning: 'register_ip_vs_protocol' defined but not used
Indeed. With no protocols selected there are no
calls to this function - all are compiled out with
ifdefs.
Maybe the best fix would be to surround this call with
ifdef-s or tune the Kconfig dependences, but I think that
marking this register function as __used is enough. No?
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix arp reply when received arp probe with sender ip 0.
Send arp reply with target ip address 0.0.0.0 and target hardware
address set to hardware address of requester. Previously sent reply
with target ip address and target hardware address set to same as
source fields.
Signed-off-by: Jonas Danielsson <the.sator@gmail.com>
Acked-by: Alexey Kuznetov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the bug, refcnt for md5sig pool was leaked when
an user try to delete a key if we have more than one key.
In addition to the leakage, we returned incorrect return
result value for userspace.
This fix should close Bug #9418, reported by <ming-baini@163.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In cases where acpi_pci_bind() does not
attach device data, acpi_pci_unbind()
complains via an ACPI exception about the missing data when
the device is removed. For example, acpi_pci_bind() does not
attach data for non-existent device functions so when the device
is removed using the ACPI PCI hotplug driver 'acpiphp' an ACPI
exception is logged for every non-existent function. This patch
avoids the confusing log messages by removing the unnecessary
ACPI exception.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix RedHat bug 329431
The idea here is separate "conscious" from "unconscious" flushes.
Conscious flushes are those due to a fsync() or close(). Unconscious
ones are flushes that occur as a side effect of some other operation or
due to memory pressure.
Currently, when an error occurs during an unconscious flush (ENOSPC or
EIO), we toss out the page and don't preserve that error to report to
the user when a conscious flush occurs. If after the unconscious flush,
there are no more dirty pages for the inode, the conscious flush will
simply return success even though there were previous errors when writing
out pages. This can lead to data corruption.
The easiest way to reproduce this is to mount up a CIFS share that's
very close to being full or where the user is very close to quota. mv
a file to the share that's slightly larger than the quota allows. The
writes will all succeed (since they go to pagecache). The mv will do a
setattr to set the new file's attributes. This calls
filemap_write_and_wait,
which will return an error since all of the pages can't be written out.
Then later, when the flush and release ops occur, there are no more
dirty pages in pagecache for the file and those operations return 0. mv
then assumes that the file was written out correctly and deletes the
original.
CIFS already has a write_behind_rc variable where it stores the results
from earlier flushes, but that value is only reported in cifs_close.
Since the VFS ignores the return value from the release operation, this
isn't helpful. We should be reporting this error during the flush
operation.
This patch does the following:
1) changes cifs_fsync to use filemap_write_and_wait and cifs_flush and also
sync to check its return code. If it returns successful, they then check
the value of write_behind_rc to see if an earlier flush had reported any
errors. If so, they return that error and clear write_behind_rc.
2) sets write_behind_rc in a few other places where pages are written
out as a side effect of other operations and the code waits on them.
3) changes cifs_setattr to only call filemap_write_and_wait for
ATTR_SIZE changes.
4) makes cifs_writepages accurately distinguish between EIO and ENOSPC
errors when writing out pages.
Some simple testing indicates that the patch works as expected and that
it fixes the reproduceable known problem.
Acked-by: Dave Kleikamp <shaggy@austin.rr.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
if (net_ratelimit())
IEEE80211_DEBUG_DROP(...)
can pollute the logs with messages like:
printk: 1 messages suppressed.
printk: 2 messages suppressed.
printk: 7 messages suppressed.
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When an interface with promisc/allmulti bit is taken down,
the mac80211 state can become confused. This fixes it by
making mac80211 keep track of all *active* interfaces that
have the promisc/allmulti bit set in the sdata, we sync
the interface bit into sdata at set_multicast_list() time
so this works.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I recently experienced unexplainable behaviour with the b43
driver when I had broken firmware uploaded. The cause may have
been that promisc mode was not correctly enabled or disabled
and this bug may have been the cause.
Note how the values are compared later in the function so
just doing the & will result in the wrong thing being
compared and the test being false almost always.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When checking the states passed in, mlx4_qp_modify() accidentally checks
cur_state twice rather than checking cur_state and new_state. Fix this
to make sure that both values are in-bounds.
Since these values may be passed in from userspace, this bug results in
userspace being able to trigger an oops.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check value ranges in ctl callbacks properly. This fixes the unexpected
crash due to wrong value assignment.
Also, remove invalid comments in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the calculation of the private_data pointer in the CS4270 driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Ingo Molnar,
when booting an allyesconfig bzImage kernel the bootup hangs in the
portman2x4 driver (on a box that does not have this hardware), at:
Pid: 1, comm: swapper
EIP: 0060:[<c02f763c>] CPU: 0
EIP is at parport_pc_read_status+0x4/0x8
EFLAGS: 00000202 Not tainted (2.6.23-rc9 #904)
EAX: f7e57a7f EBX: 00000010 ECX: c2b808c0 EDX: 00000379
ESI: f7cb8230 EDI: 00000010 EBP: f7cb8230 DS: 007b ES: 007b FS: 0000
CR0: 8005003b CR2: fff9c000 CR3: 007ec000 CR4: 00000690
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c04613de>] portman_flush_input+0xde/0x12c
[<c0461a24>] snd_portman_probe+0x368/0x484
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02fce68>] platform_drv_probe+0xc/0x10
[<c02fba6c>] driver_probe_device+0x74/0x194
[<c0587174>] klist_next+0x38/0x70
[<c02fbb8c>] __device_attach+0x0/0x8
[<c02faea1>] bus_for_each_drv+0x35/0x68
[<c02fbc22>] device_attach+0x72/0x78
the reason is due to an inconsistent error return code of 1 or 2, while
snd_portman_probe only realizes negative error codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The driver assigns the write proc callback to read wrongly.
Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The Samsung S3C24xx uses new architecture file layout in the post 2.6.23
kernel. This patch fixes include path for the s3c2443-ac97.c.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When connection tracking entry (nf_conn) is about to copy itself it can
have some of its extension users (like nat) as being already freed and
thus not required to be copied.
Actually looking at this function I suspect it was copied from
nf_nat_setup_info() and thus bug was introduced.
Report and testing from David <david@unsolicited.net>.
[ Patrick McHardy states:
I now understand whats happening:
- new connection is allocated without helper
- connection is REDIRECTed to localhost
- nf_nat_setup_info adds NAT extension, but doesn't initialize it yet
- nf_conntrack_alter_reply performs a helper lookup based on the
new tuple, finds the SIP helper and allocates a helper extension,
causing reallocation because of too little space
- nf_nat_move_storage is called with the uninitialized nat extension
So your fix is entirely correct, thanks a lot :) ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit systems sizeof(struct ifreq) is 8 bytes larger than
sizeof(struct iwreq).
For GET calls, the wireless extension code copies back into userspace
using sizeof(struct ifreq) but userspace and elsewhere only allocates
a "struct iwreq". Thus, this copy writes past the end of the iwreq
object and corrupts whatever sits after it in memory.
Fix the copy_to_user() length.
This particularly hurts the compat case because the wireless compat
code uses compat_alloc_userspace() and right after this allocated
buffer is the current bottom of the user stack, and that's what gets
overwritten by the copy_to_user() call.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all subchannel handling is done on the slow path workqueue
so that we don't have races between an old subchannel unregistering
and a new subchannel with the same name registering.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Before we're getting short on memory detection fixes here is the next
one: if neither sclp nor diag260 report the storage size the detection
loop will return immediately without detecting anything. Fix this by
breaking the detection loop only if the memory end is known.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iucv is the only user of the various functions that are used to bring
parts of cpus up and down. Its the only allocpercpu user that will do
I/O on per cpu objects (which is difficult to do with virtually mapped memory).
And its the only use of allocpercpu where a GFP_DMA allocation is done.
Remove the allocpercpu calls from iucv and code the allocation and freeing
manually. After this patch it is possible to remove a large part of
the allocpercpu API.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't perform a sigp store-status-at-address on smp_send_stop().
It will overwrite the lowcores of other cpus and destroys valueable
debug informations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
page_mkclean used to call page_clear_dirty for every given page. This
is different to all other architectures, where the dirty bit in the
PTEs is only resetted, if page_mapping() returns a non-NULL pointer.
We can move the page_test_dirty/page_clear_dirty sequence into the
2nd if to avoid unnecessary iske/sske sequences, which are expensive.
This change also helps kvm for s390 as the host must transfer the
dirty bit into the guest status bits. By moving the page_clear_dirty
operation into the 2nd if, the vm will only call page_clear_dirty
for pages where it walks the mapping anyway. There it calls
ptep_clear_flush for writable ptes, so we can transfer the dirty bit
to the guest.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When returning from IRQ handling and TIF_NEED_RESCHED is set we must
call preempt_schedule_irq() instead of schedule().
Otherwise the BKL might be unlocked in schedule() and therfore
everything that relies on the BKL is broken.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When doing an magic sysrq reboot on s390 the following bug message
appears:
SysRq : Resetting
BUG: sleeping function called from invalid context at include/asm/semaphore.h:61
in_atomic():1, irqs_disabled():0
07000000004002a8 000000000fe6bc48 0000000000000002 0000000000000000
000000000fe6bce8 000000000fe6bc60 000000000fe6bc60 000000000012a79a
0000000000000000 07000000004002a8 0000000000000006 0000000000000000
0000000000000000 000000000fe6bc48 000000000000000d 000000000fe6bcb8
00000000004000c8 0000000000103234 000000000fe6bc48 000000000fe6bc90
Call Trace:
(¬<00000000001031b2>| show_trace+0x12e/0x148)
¬<000000000011ffca>| __might_sleep+0x10a/0x118
¬<0000000000129fba>| acquire_console_sem+0x92/0xf4
¬<000000000012a2ca>| console_unblank+0xc2/0xc8
¬<0000000000107bb4>| machine_restart+0x54/0x6c
¬<000000000028e806>| sysrq_handle_reboot+0x26/0x30
¬<000000000028e52a>| __handle_sysrq+0xa6/0x180
¬<0000000000140134>| run_workqueue+0xcc/0x18c
¬<000000000014029a>| worker_thread+0xa6/0x108
¬<00000000001458e4>| kthread+0x64/0x9c
¬<0000000000106f0e>| kernel_thread_starter+0x6/0xc
¬<0000000000106f08>| kernel_thread_starter+0x0/0xc
The only reason for doing a console_unblank on s390 is to flush the
log buffer. We have to check for in_atomic before doing a
console_unblank as the console is otherwise filled with an unrelated
bug message.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Modify the sense id channel program to allow device sensing of pav
alias devices which belong to a base device with ungrouped paths.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
My changes to _tlbie to fix 4xx unfortunately broke 8xx build in a
couple of places. This fixes it.
Spotted by Olof Johansson.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
From: "Sam Jansen" <sjansen@google.com>
sysctl_tcp_congestion_control seems to have a bug that prevents it
from actually calling the tcp_set_default_congestion_control
function. This is not so apparent because it does not return an error
and generally the /proc interface is used to configure the default TCP
congestion control algorithm. This is present in 2.6.18 onwards and
probably earlier, though I have not inspected 2.6.15--2.6.17.
sysctl_tcp_congestion_control calls sysctl_string and expects a successful
return code of 0. In such a case it actually sets the congestion control
algorithm with tcp_set_default_congestion_control. Otherwise, it returns the
value returned by sysctl_string. This was correct in 2.6.14, as sysctl_string
returned 0 on success. However, sysctl_string was updated to return 1 on
success around about 2.6.15 and sysctl_tcp_congestion_control was not updated.
Even though sysctl_tcp_congestion_control returns 1, do_sysctl_strategy
converts this return code to '0', so the caller never notices the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen_output_ipsec() function can unlock this lock twice
due to merged error and plain paths. Remove one of the calls
to spin_unlock.
Other possible solution would be to place "return 0" right
after the first unlock, but at this place the err is known
to be 0, so these solutions are the same except for this one
makes the code shorter.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl table check failed: /net/ipv4/vs/lblc_expiration .3.5.21.19 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/lblcr_expiration .3.5.21.20 Missing strategy
Switch these entried over to use CTL_UNNUMBERED as clearly
the sys_syscal portion wasn't working.
This is along the same lines as Christian Borntraeger's patch that fixes
up entries with no stratergy in net/ipv4/ipvs/ip_vs_ctl.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.
* 8544 DS:
- Fix interrupt mask
- Be explicit about use of INTA for on chip peripherals
* 8572 DS/8641 HPCN:
- Fix interrupt mask
- Expand interrupt map for PCI slots to cover all functions
- Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we get no user time and no system time allocated since the last
account_system_vtime, the system to user time ratio estimate can end
up dividing by zero.
This was causing a problem noticed by Balbir Singh.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can currently cause an oops by repeatedly creating and destroying
contexts, while doing getdents() calls on the "/spu" directory.
This is due to the context's top-level dentry remaining hashed while
the context is being destroyed.
Fix this by unhashing the context's dentry with the
dentry->d_inode->i_mutex held. This way, we'll hit the check for
d_unhashed in dentry_readdir, and won't be included in the
list of subdirs for /spu.
test: spufs-testsuite:tests/01-spu_create/07-destroy-vs-readdir-race
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If on a rev. 2.1, adjust UCC clock and data timing characteristics
as specified in the rev.2.1 erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A h/w bug requires we program the PHY in RGMII mode for internal delay
on the receive or transmit side only; document the new property values.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
correct the reg property, remove duplicate io port entry, whitespace fixes.
Thanks to Peter Van Ackeren for pointing this out.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
currently the board-level PHY reset code for the mpc832x MDS messes with
reset configuration words source settings which is plain wrong (it
looks like this board code was cut-n-pasted from the mpc8360 mds code,
which has the PHY reset bits in a different BCSR); this patch points
the PHY reset code to the proper mpc832x mds PHY reset bits in the BCSR.
Signed-off-by: Peter Van Ackeren <peter.vanackeren@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch does fix potential NULL pointer dereference that could take
place inside of strcmp() if of_get_property() call failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current VDSO implementation is hardcoded to 128 byte cache blocks,
which are only used on IBM's 64-bit processors.
Convert it to get the cache block sizes out of vdso_data instead,
similar to how the ppc64 in-kernel cache flush does it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355
cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Port 18eab85503
(Enable C3 even when PM2_control is zero) to cpuidle.
Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When retrying kernel_recvmsg() because of a short read, check returned
length against the remaining length, not against total length. This
avoids unneeded session reconnects which would otherwise occur when
kernel_recvmsg() finally returns zero when asked to read zero bytes.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Due to an erratum, we don't want to reset the mpic at boot time. It can
sometimes cause problems with lost interrupts later on while running.
Signed-off-by: Olof Johansson <olof@lixom.net>
On platforms doing non-coherent DMA (4xx, 8xx, ...), it's important
that the kmalloc minimum alignment is set to the cache line size, to
avoid sharing cache lines between different objects, so that DMA to
one of the objects doesn't corrupt the other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Include <asm/iseries/hv_call.h> in arch/powerpc/mm/stab.c to fix the
following compile error (found with randconfig):
CC arch/powerpc/mm/stab.o
arch/powerpc/mm/stab.c: In function "stab_initialize":
arch/powerpc/mm/stab.c:282: error: implicit declaration of function "HvCall1"
arch/powerpc/mm/stab.c:282: error: "HvCallBaseSetASR" undeclared (first use in this function)
arch/powerpc/mm/stab.c:282: error: (Each undeclared identifier is reported only once
arch/powerpc/mm/stab.c:282: error: for each function it appears in.)
make[1]: *** [arch/powerpc/mm/stab.o] Error 1
make: *** [arch/powerpc/mm] Error 2
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the ITE Tech Inc. IT8712F EC-LPC Super I/O
chipset found on many Pentium III and AMD motherboards. Developed using code
from other watchdog drivers and the datasheet on ITE Tech homepage.
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
set_ibm_param() could OOPS with a NULL pointer derreference if one did not give
any values for a module parameter it handles. This would, of course, cause all
sort of trouble for future modprobing and require a reboot to clean up
properly.
Fix it by returning -EINVAL if no values are given for the parameter, and also
avoid any nastyness from BUG_ON while at it.
How to reproduce: modprobe thinkpad-acpi brightness
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Tested-by: Mike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: Len Brown <len.brown@intel.com>
cpwatchdog, remove SPIN_LOCK_UNLOCKED
SPIN_LOCK_UNLOCKED is deprecated, use __SPIN_LOCK_UNLOCKED with an unique
name instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If no address is given for the W83697HF/HG watchdog IO port, stop looping
through possible locations when a watchdog device has been found.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch enables the watchdog to read out the reset cause after a boot and
provide this to the user.
The driver will now also return -EIO if probed when booting from a watchdog
reset. This is due to a silicon errata in the AT32AP700x devices.
Detailed description and work-arounds can be found in the errata section of the
datasheet avilable from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Check the value ranges in ctl put callbacks properly.
Some callbacks may access a wrong pointer depending on the value passed.
Also, fixed the access to the wrong field for enum values, and fixed
some callbacks to return the proper error code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The recent addition of checking PINCAP for EAPD seems to break some
systems due to unexpected response from the codec chip. We shouldn't
issue GET_PINCAP verb to non-PIN widgets. Now checks the widget type
before checking EAPD bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When the output and input ports are used at the same time, the timer can
be interrupted by the hardware interrupt, so we have to disable
interrupts when we take a lock in the timer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the definitions of the CM_FLINKON/CM_FLINKOFF register bits that
were garbled in the last 'update register definitions' patch.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
AD1986A has a hardware problem that it cannot share a stream with
multiple pins properly. The problem occurs e.g. when a volume is changed
during playback.
So far, hda-intel driver unconditionally assigns the stream to multiple
output pins in copy-front mode, and this should be avoided for AD1986A
codec.
The original fix patch was by zhejiang <zhe.jiang@intel.com>.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduce new ACPI_PROCFS_POWER (default Yes) config option and move
procfs code in battery, ac, and sbs drivers under it.
This is done to allow ACPI_PROCFS to be default No.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes arch/ppc 440EP platforms to setup the FPU correctly. A virtual
PVR is used, as 440GR platforms share an identical hardware PVR value and do
not have an FPU.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds uic_mask_ack_irq() callback to PowerPC 4xx uic code
to avoid kernel crash. It is used for edge-triggered interrupts
by handle_uic_irq().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
pcibios_free_controller() is now available for both 32 and 64 bits
but the header only declares it for 64 bits. This moves the
declaration down next to the pcibios_alloc_controller() one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are several issues with the rtas_ibm_suspend_me code, which
enables platform-assisted suspension of an LPAR as covered in PAPR
2.2.
1.) rtas_ibm_suspend_me uses on_each_cpu() to invoke
rtas_percpu_suspend_me on all cpus via IPI:
if (on_each_cpu(rtas_percpu_suspend_me, &data, 1, 0))
...
'data' is on the calling task's stack, but rtas_ibm_suspend_me takes
no measures to ensure that all instances of rtas_percpu_suspend_me are
finished accessing 'data' before returning. This can result in the
IPI'd cpus accessing random stack data and getting stuck in H_JOIN.
This is addressed by using an atomic count of workers and a completion
on the stack.
2.) rtas_percpu_suspend_me is needlessly calling H_JOIN in a loop.
The only event that can cause a cpu to return from H_JOIN is an H_PROD
from another cpu or a NMI/system reset. Each cpu need call H_JOIN
only once per suspend operation.
Remove the loop and the now unnecessary 'waiting' state variable.
3.) H_JOIN must be called with MSR[EE] off, but lazy interrupt
disabling may cause the caller of rtas_ibm_suspend_me to call H_JOIN
with it on; the local_irq_disable() in on_each_cpu() is not
sufficient.
Fix this by explicitly saving the MSR and clearing the EE bit before
calling H_JOIN.
4.) H_PROD is being called with the Linux logical cpu number as the
parameter, not the platform interrupt server value. (It's also being
called for all possible cpus, which is harmless, but unnecessary.)
This is fixed by calling H_PROD for each online cpu using
get_hard_smp_processor_id(cpu) for the argument.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I haven't had this hardware in years, so kill off my MAINTAINERS entry
for this and flag it as orphaned.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ICH8 and 9 use two SFF controllers to show 6 SATA ports. The first
controllre hosts the first 4 ports while the second one hosts the last
2. The PCS register of the first controller encompasses the first
four ports or all six ports depending on configuration while PCS of
the second controller controls the last two ports. Using 0xf for the
first controller and 0x3 for the second controller always result in
the correct configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
DaveM has provided a vger list, update MAINTAINERS to reflect this.
Also, rip out the sh64 entry (as this can just be rolled in to the
general sh case), and add the git path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the refactored update_mmu_cache() introduced in older kernels,
there's no longer any need to take the page_table_lock in this path,
so simply drop it completely.
Without this, performance degradation is seen on SMP on heavily
threaded workloads that don't use the split ptlock, and ultimately
we have no reason to contend for the lock in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __do_page_fault() fast-path contains a UTLB flush in order to
force an ITLB reload, this isn't needed in practice as the ITLB is
auto-reloaded from the UTLB anyways, which is already displaced by
the manual 'ldtlb' in the update_mmu_cache() path.
This provides a measurable speed up in the TLB miss fast-path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ICH8M on apple macbook pro occasionally locks up completely during PCS
initialization if ports other than the first one are enabled. Add a
separate controller ID and only enable the first port.
tj: commit description added and patch updated to fit with the
previous controller ID update.
Signed-off-by: Thomas Rohwer <tr@tng.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move piix_pata_mwdma to top, rename ich9_2port_sata to ich8_2port_sata
for consistency and use automatically incremented values instead of
assigning fixed values to ease adding new controller IDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Sebastian Kemper reported that issuing CD/DVD commands under libata is
not fully compatible with ide-scsi. In particular, the
GPCMD_SET_STREAMING was being rejected at the host level in some
instances.
The reason is that libata-scsi insists upon the cmd_len field exactly
matching the SCSI opcode being issued, whereas ide-scsi tolerates
12-byte commands contained within a 16-byte (cmd_len) CDB.
There doesn't seem to be a good reason for us to not be compatible
there, so here is a patch to fix libata-scsi to permit SCSI opcodes so
long as they fit within whatever size CDB is provided.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Per Mark's comments, maybe all ATAPI tape drives need ATA_HORKAGE_STUCK_ERR.
This patch applys ATA_HORKAGE_STUCK_ERR for all ATAPI tape drives.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Satellite U205 has alternate product name where the satellite part is
all capatalized. Add it to the blacklist.
This is reported by Ross Patterson in kernel bugzilla bug #7780.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ross Patterson <me@rpatterson.net>
Indeed my previous change to alloc_pskb has made it possible
for the TCP header to be misaligned iff the MTU is not a multiple
of 4 (and less than a page). So I suspect the optimised IPsec
MTU calculation is giving you just such an MTU :)
This patch fixes it by changing alloc_pskb to make sure that
the size is at least 32-bit aligned. This does not cause the
problem fixed by the previous patch because max_header is always
32-bit aligned which means that in the SG/NOTSO case this will
be a no-op.
I thought about putting this in the callers but all the current
callers are from TCP. If and when we get a non-TCP caller we
can always create a TCP wrapper for this function and move the
alignment over there.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that stats of cpu 0 are counted twice, since
for_each_possible_cpu() is looping on all possible cpus, including 0
Before percpu conversion of ip_rt_acct, we should also remove the
assumption that CPU 0 is online (or even possible)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usb max packet size won't change during the
device's presence. We should store it in a
variable inside rt2x00dev and use that.
This should also fix a division error when the
device is being hot-unplugged while a frame is
being send out.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The virtio code never hooked through the ->remove callback. Although
noone supports device removal at the moment, this code is already
needed for module unloading.
This of course also revealed bugs in virtio_blk, virtio_net and lguest
unloading paths.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
drivers/acpi/sbs.c: In function acpi_battery_add:
drivers/acpi/sbs.c:811: warning: ignoring return value of device_create_file,
declared with attribute warn_unused_result
Additional cleanups:
* use struct acpi_battery in acpi_battery_remove() to clean up function
calls, just like acpi_battery_add() already does.
* put braces around unregister call, as it depends on dev being not NULL.
* remove unneeded braces
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Hi Trond,
I have discovered that the BUG_ON in nfs_follow_mountpoint:
BUG_ON(IS_ROOT(dentry));
can be triggered by a misbehaving server.
What happens is the client does a lookup and discoveres that the named
directory has a different fsid, so it initiates a mount.
It then performs a GETATTR on the mounted directory and gets a
different fsid again (due to a bug in the NFS server).
This causes nfs_follow_mountpoint to be called on the newly mounted
root, which triggers the BUG_ON.
To duplicate this, have a directory which contains some mountpoints,
and export that directory with the "crossmnt" flag using nfs-utils
1.1.1 (or 1.1.0 I think)
The GETATTR on the root of the mounted filesystem will return the
information for the top exportpoint, while a lookup will return the
correct information. This difference causes the NFS client to BUG.
I think the best way to fix this is to trap this possibility early, so
just before completing the mount in the NFS client, check that it isn't
going to use nfs_mountpoint_inode_operations.
As long as i_op will never change once set (is that true?), this
should be adequately safe.
The following patch shows a possible approach, and it works for me.
i.e. when the NFS server is misbehaving, I get ESTALE on those
mountpoints, while when the NFS server is working correctly, I get
correct behaviour on the client.
NeilBrown
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pipe messages start out life on a queue on the inode, but when first
read they're moved to the filp's private pointer. So it's possible for
a poll here to return null even though there's a partially read message
available.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Return an error from gss_import_sec_context_kerberos if the
negotiated context contains encryption or checksum types not
supported by the kernel code.
This fixes an Oops because success was assumed and later code found
no internal_ctx_id.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Instead of mapping all errors except EACCES to EAGAIN, map all errors
except EAGAIN to EACCES.
An example is user-land negotiating a Kerberos context with an encryption
type that is not supported by the kernel code. (This can happen due to
mis-configuration or a bug in the Kerberos code that does not honor our
request to limit the encryption types negotiated.) This failure is not
transient, and returning EAGAIN causes mount to continuously retry rather
than giving up.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since 2.6.18, the superblock sb->s_root has been a dummy dentry with a
dummy inode. This breaks ustat(), which actually uses sb->s_root in a
vfstat() call.
Fix this by making the s_root a dummy alias to the directory inode that was
used when creating the superblock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: simplify "make ARCH=x86" and fix kconfig all.config
x86: reboot fixup for wrap2c board
x86: check boundary in count setup resource
x86: fix reboot with no keyboard attached
x86: add hpet sanity checks
x86: on x86_64, correct reading of PC RTC when update in progress in time_64.c
x86: fix freeze in x86_64 RTC update code in time_64.c
ntp: fix typo that makes sync_cmos_clock erratic
Remove x86 merge artifact from top Makefile
x86: fixup cpu_info array conversion
x86: show cpuinfo only for online CPUs
x86: fix cpu-hotplug regression
x86: ignore the sys_getcpu() tcache parameter
x86: voyager use correct header file name
x86: fix smp init sections
x86: fix voyager_cat_init section
x86: fix bogus memcpy in es7000_check_dsdt()
Simplify "make ARCH=x86" and fix kconfig so we again can set 64BIT in
all.config.
For a fix the diffstat is nice:
6 files changed, 3 insertions(+), 36 deletions(-)
The patch reverts these commits:
- 0f855aa64b ("kconfig: add helper to set
config symbol from environment variable")
- 2a113281f5 ("kconfig: use $K64BIT to
set 64BIT with all*config targets")
Roman Zippel pointed out that kconfig supported string compares so
the additional complexity introduced by the above two patches were
not needed.
With this patch we have following behaviour:
# make {allno,allyes,allmod,rand}config [ARCH=...]
option \ host arch | 32bit | 64bit
=====================================================
./. | 32bit | 64bit
ARCH=x86 | 32bit | 32bit
ARCH=i386 | 32bit | 32bit
ARCH=x86_64 | 64bit | 64bit
The general rule are that ARCH= and native architecture takes
precedence over the configuration.
So make ARCH=i386 [whatever] will always build a 32-bit kernel
no matter what the configuration says. The configuration will
be updated to 32-bit if it was configured to 64-bit and the
other way around.
This behaviour is consistent with previous behaviour so no
suprises here.
make ARCH=x86 will per default result in a 32-bit kernel but as
the only ARCH= value x86 allow the user to select between 32-bit
and 64-bit using menuconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Herrmann <aherrman@arcor.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify "make ARCH=x86" and fix kconfig so we again
can set 64BIT in all.config.
For a fix the diffstat is nice:
6 files changed, 3 insertions(+), 36 deletions(-)
The patch reverts these commits:
0f855aa64b
-> kconfig: add helper to set config symbol from environment variable
2a113281f5
-> kconfig: use $K64BIT to set 64BIT with all*config targets
Roman Zippel pointed out that kconfig supported string
compares so the additional complexity introduced by the
above two patches were not needed.
With this patch we have following behaviour:
# make {allno,allyes,allmod,rand}config [ARCH=...]
option \ host arch | 32bit | 64bit
=====================================================
./. | 32bit | 64bit
ARCH=x86 | 32bit | 32bit
ARCH=i386 | 32bit | 32bit
ARCH=x86_64 | 64bit | 64bit
The general rule are that ARCH= and native architecture
takes precedence over the configuration.
So make ARCH=i386 [whatever] will always build a 32-bit
kernel no matter what the configuration says.
The configuration will be updated to 32-bit if it was
configured to 64-bit and the other way around.
This behaviour is consistent with previous behaviour so
no suprises here.
make ARCH=x86 will per default result in a 32-bit kernel
but as the only ARCH= value x86 allow the user to select
between 32-bit and 64-bit using menuconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Herrmann <aherrman@arcor.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Revert this patch:
move the init sections to the end of memory, so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation. When doing this, we also pack some of the other
sections a little closer together, to make sure we don't waste memory.
To make this happen, we need to rename the .data.init_task section to
.init_task.data, so it doesn't get picked up by the linker script glob.
Since it causes the kernel not to boot up with mtd filesystems.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
/*
* CPUs often take a performance hit when accessing unaligned memory
* locations. The actual performance hit varies, it can be small if the
* hardware handles it or large if we have to take an exception and fix
* it
* in software.
*
* Since an ethernet header is 14 bytes network drivers often end up
* with
* the IP header at an unaligned offset. The IP header can be aligned by
* shifting the start of the packet by 2 bytes. Drivers should do this
* with:
*
* skb_reserve(NET_IP_ALIGN);
*
* The downside to this alignment of the IP header is that the DMA is
* now
* unaligned. On some architectures the cost of an unaligned DMA is high
* and this cost outweighs the gains made by aligning the IP header.
*
* Since this trade off varies between architectures, we allow
* NET_IP_ALIGN
* to be overridden.
*/
This new function insl_16 allows to read form 32-bit IO and writes to
16-bit aligned memory. This is useful in above described scenario -
In particular with the AXIS AX88180 Gigabit Ethernet MAC.
Once the device is in 32-bit mode, reads from the RX FIFO always
decrements 4bytes.
While on the other side the destination address in SDRAM is always
16-bit aligned.
If we use skb_reserve(0) the receive buffer is 32-bit aligned but later
we hit a unaligned exception in the IP code.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Some BIOSes advertise HPET at 0x0. We really do no want to
allocate a resource there. Check for it and leave early.
Other BIOSes tell us the HPET is at 0xfed0000000000000
instead of 0xfed00000. Add a check and fix it up with a warning
on user request.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Correct potentially unstable PC RTC time register reading in time_64.c
Stop the use of an incorrect technique for reading the standard PC RTC
timer, which is documented to "disconnect" time registers from the bus
while updates are in progress. The use of UIP flag while interrupts
are disabled to protect a 244 microsecond window is one of the
Motorola spec sheet's documented ways to read the RTC time registers
reliably.
tglx: removed locking changes from original patch, as they gain nothing
(read_persistent_clock is only called during boot, suspend, resume - so
no hot path affected) and conflict with the paravirt locking scheme
(see 32bit code), which we do not want to complicate for no benefit.
Signed-off-by: David P. Reed <dpreed@reed.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix hard freeze on x86_64 when the ntpd service calls
update_persistent_clock()
A repeatable but randomly timed freeze has been happening in Fedora 6
and 7 for the last year, whenever I run the ntpd service on my AMD64x2
HP Pavilion dv9000z laptop. This freeze is due to the use of
spin_lock(&rtc_lock) under the assumption (per a bad comment) that
set_rtc_mmss is called only with interrupts disabled. The call from
ntp.c to update_persistent_clock is made with interrupts enabled.
Signed-off-by: David P. Reed <dpreed@reed.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix a typo in ntp.c that has caused updating of the persistent (RTC)
clock when synced to NTP to behave erratically.
When debugging a freeze that arises on my AMD64 machines when I
run the ntpd service, I added a number of printk's to monitor the
sync_cmos_clock procedure. I discovered that it was not syncing to
cmos RTC every 11 minutes as documented, but instead would keep trying
every second for hours at a time. The reason turned out to be a typo
in sync_cmos_clock, where it attempts to ensure that
update_persistent_clock is called very close to 500 msec. after a 1
second boundary (required by the PC RTC's spec). That typo referred to
"xtime" in one spot, rather than "now", which is derived from "xtime"
but not equal to it. This makes the test erratic, creating a
"coin-flip" that decides when update_persistent_clock is called - when
it is called, which is rarely, it may be at any time during the one
second period, rather than close to 500 msec, so the value written is
needlessly incorrect, too.
Signed-off-by: David P. Reed
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x86 merge modified the tags target to handle the two separate
source directories. Remove it now that i386/x86_64 are gone completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
92cb7612ae sets cpu_info->cpu_index to zero
for no reason. Referencing cpu_info->cpu_index now points always to CPU#0,
which is apparently not what we want.
Remove it.
Spotted-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix regressions introduced with 92cb7612ae.
It can happen that cpuinfo is displayed for CPUs that are not online or
even worse for CPUs not present at all. As an example, following was
shown for a "second" CPU of a single core K8 variant:
processor : 0
vendor_id : unknown
cpu family : 0
model : 0
model name : unknown
stepping : 0
cache size : 0 KB
fpu : yes
fpu_exception : yes
cpuid level : 0
wp : yes
flags :
bogomips : 0.00
clflush size : 0
cache_alignment : 0
address sizes : 0 bits physical, 0 bits virtual
power management:
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit d435d862ba
("cpu hotplug: mce: fix cpu hotplug error handling")
changed the error handling in mce_cpu_callback.
In cases where not all CPUs are brought up during
boot (e.g. using maxcpus and additional_cpus parameters)
mce_cpu_callback now returns NOTFIY_BAD because
for such CPUs cpu_data is not completely filled when
the notifier is called. Thus mce_create_device fails right
at its beginning:
if (!mce_available(&cpu_data[cpu]))
return -EIO;
As a quick fix I suggest to check boot_cpu_data for MCE.
To reproduce this regression:
(1) boot with maxcpus=2 addtional_cpus=2 on a 4 CPU x86-64 system
(2) # echo 1 >/sys/devices/system/cpu/cpu2/online
-bash: echo: write error: Invalid argument
dmesg shows:
_cpu_up: attempt to bring up CPU 2 failed
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
dont use the vgetcpu tcache - it's causing problems with tasks
migrating, they'll see the old cache up to a jiffy after the
migration, further increasing the costs of the migration.
In the worst case they see a complete bogus information from
the tcache, when a sys_getcpu() call "invalidated" the cache
info by incrementing the jiffies _and_ the cpuid info in the
cache and the following vdso_getcpu() call happens after
vdso_jiffies have been incremented.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix header file name for Voyager build.
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-voyager/setup_arch.h:2:26: error: asm/setup_32.h: No such file or directory
make[1]: *** [arch/x86/kernel/setup_32.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix Voyager section mismatch due to using __devinit instead of __cpuinit.
WARNING: vmlinux.o(.text+0xd943): Section mismatch: reference to .init.text:init_gdt (between 'voyager_smp_prepare_boot_cpu' and 'smp_vic_cmn_interrupt')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
es7000_check_dst() contains a memcpy from 0, which probably should have been
a memset. Remove it and check the retunr value from acpi_get_table_header.
Noticed by: Joe Perches <joe@perches.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only user of get_wchan I was able to find is the proc fs - and proc
can't be built modular.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The only user is the a.out support.
It was therefore removed prior to the blackfin merge from all
architectures not supporting a.out.
Currently, Blackfin doesn't suppport a.out.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
i'm *reasonably* confident that this is a typo that should be fixed.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_TSS was erroneously ignored, in favor of the FADT.
When TSS is used, the access width is included in the PTC control/status
register. So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.
It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the function interface for throttling control via PTC.
The following functions are concerned:
acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.
Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the following section mismatches with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.data+0x23640): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x2366c): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
WARNING: vmlinux.o(.data+0x23698): Section mismatch: reference to .init.text.20:can_skip_ioresource_align (between 'acpi_pciprobe_dmi_table' and 'pcibios_irq_mask')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Have CIFS_SessSetup call cifs_get_spnego_key when Kerberos is
negotiated. Use the info in the key payload to build a session
setup request packet. Also clean up how the request buffer in
the function is freed on error.
With appropriate user space helper (in samba/source/client). Kerberos
support (secure session establishment can be done now via Kerberos,
previously users would have to use NTLMv2 instead for more secure
session setup).
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
...and populate it with the hostname portion of the UNC string.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Move all of the kfree's sprinkled in the middle of the function to the
end, and have the code set rc and just goto there on error. Also zero
out the password string before freeing it. Looks like this should also
fix a potential memory leak of the prepath string if an error occurs
near the end of the function.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Calling zfcp_erp_strategy_check_action() after zfcp_erp_action_to_running()
in zfcp_erp_strategy() might cause an unbalanced up() for erp_ready_sem,
which makes the zfcp recovery fail somewhere along the way:
erp thread processing erp_action:
|
| someone waking up erp thread for erp_action
| |
| | someone else dismissing erp_action:
| | |
V V V
write_lock_irqsave(&adapter->erp_lock, flags);
...
if (zfcp_erp_action_exists(erp_action) == ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem); /* first up() for erp_action */
}
write_unlock_irqrestore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
...
zfcp_erp_action_to_running(erp_action);
write_unlock_restore(&adapter->erp_lock, flags);
/* processing erp_action */
write_lock_irqsave(&adapter->erp_lock, flags);
...
erp_action->status |= ZFCP_STATUS_ERP_DISMISSED;
if (zfcp_erp_action_exists(erp_action) ==
ZFCP_ERP_ACTION_RUNNING) {
zfcp_erp_action_to_ready(erp_action);
up(&adapter->erp_ready_sem);
/* second, unbalanced up() for erp_action */
}
...
write_unlock_restore(&adapter->erp_lock, flags);
write_lock_irqsave(&adapter->erp_lock, flags);
if (erp_action->status & ZFCP_STATUS_ERP_DISMISSED) {
zfcp_erp_action_dequeue(erp_action);
retval = ZFCP_ERP_DISMISSED;
}
...
write_unlock_restore(&adapter->erp_lock, flags);
down(&adapter->erp_ready_sem);
/* this down() is meant to balance the first up() */
The erp thread must not dismiss an erp_action after moving that action to
erp_running_head. Instead it should just go through the down() operation,
which balances the first up(), and run through zfcp_erp_strategy one more
time for the second up(), which eventually cleans up erp_action. Which
is similar to the normal processing of an event for erp_action doing
something asynchronously (e.g. waiting for the completion of an fsf_req).
This only works if we make sure that a dismissed erp_action is passed to
zfcp_erp_strategy() prior to the other action, which caused actions to be
dismissed. Therefore the patch implements this rule: running actions go to
the head of the ready list; new actions go to the tail of the ready list;
the erp thread picks actions to be processed from the ready list's head.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp_erp_action_dismiss() used to ignore any actions in the ready list. This
is a bug. Any action superseded by a stronger action needs to be dismissed.
This patch changes zfcp_erp_action_dismiss() so that it dismisses actions
regardless of their list affiliation. The ERP thread is able to handle this.
It is important to kick the erp thread only for actions in the running list,
though, as an imbalance of wakeup signals would confuse the erp thread
otherwise.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
VDSP has double fault on core a/b inverted for BF561 -- bit 11 is core a while bit 12 is core b
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
since we have this always turned on now and dont want it off (and hasnt been an option in a while)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
move the init sections to the end of memory, so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation. When doing this, we also pack some of the other
sections a little closer together, to make sure we don't waste memory.
To make this happen, we need to rename the .data.init_task section to
.init_task.data, so it doesn't get picked up by the linker script glob.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the parameters.
Fixed to missing initialization of sg lists before calling
for_each_sg() by Jes Sorensen - sg list needs to be initialized before
trying to pull the elements out of it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, the iSCSI driver returns the data transfer residual for
data-in commands (e.g. read) but not data-out commands (e.g. write).
This patch makes it return the data transfer residual for both types of
commands.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is a race condition in iscsi_tcp.c that may cause it to forget
that it received a R2T from the target. This race may cause a data-out
command (such as a write) to lock up. The race occurs here:
static int
iscsi_send_unsol_pdu(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask)
{
struct iscsi_tcp_cmd_task *tcp_ctask = ctask->dd_data;
int rc;
if (tcp_ctask->xmstate & XMSTATE_UNS_HDR) {
BUG_ON(!ctask->unsol_count);
tcp_ctask->xmstate &= ~XMSTATE_UNS_HDR; <---- RACE
...
static int
iscsi_r2t_rsp(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask)
{
...
tcp_ctask->xmstate |= XMSTATE_SOL_HDR_INIT; <---- RACE
...
While iscsi_xmitworker() (called from scsi_queue_work()) is preparing to
send unsolicited data, iscsi_tcp_data_recv() (called from
tcp_read_sock()) interrupts it upon receipt of a R2T from the target.
Both contexts do read-modify-write of tcp_ctask->xmstate. Usually, gcc
on x86 will make &= and |= atomic on UP (not guaranteed of course), but
in this case iscsi_send_unsol_pdu() reads the value of xmstate before
clearing the bit, which causes gcc to read xmstate into a CPU register,
test it, clear the bit, and then store it back to memory. If the recv
interrupt happens during this sequence, then the XMSTATE_SOL_HDR_INIT
bit set by the recv interrupt will be lost, and the R2T will be
forgotten.
The patch below (against 2.6.24-rc1) converts accesses of xmstate to use
set_bit, clear_bit, and test_bit instead of |= and &=. I have tested
this patch and verified that it fixes the problem. Another possible
approach would be to hold a lock during most of the rx/tx setup and
post-processing, and drop the lock only for the actual rx/tx.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
list_for_each_safe() only protects list from list alterations
performed by the same thread. One still needs to implement
proper locking when list is being accessed from several threads.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If input_register_device() fails input_free_device() must
be called to release memory allocated for the device.
Also consolidate error handling in acpi_bus_video_add()
and handle input_allocate_device() failures.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Properly set up parent on input device registered by the video driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
request
In SendReceive() function in transport.c - it memcpy's
message payload into a buffer passed via out_buf param. The function
assumes that all buffers are of size (CIFSMaxBufSize +
MAX_CIFS_HDR_SIZE) , unfortunately it is also called with smaller
(MAX_CIFS_SMALL_BUFFER_SIZE) buffers. There are eight callers
(SMB worker functions) which are primarily affected by this change:
TreeDisconnect, uLogoff, Close, findClose, SetFileSize, SetFileTimes,
Lock and PosixLock
CC: Dave Kleikamp <shaggy@austin.ibm.com>
CC: Przemyslaw Wegrzyn <czajnik@czajsoft.pl>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
We currently do not. Also make it easier to handle cplb violations - in traps.c
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Actually there are several but one is trivially fixed
1. FSACTL_GET_NEXT_ADAPTER_FIB ioctl does not lock dev->fib_list
but needs to
2. Ditto for FSACTL_CLOSE_GET_ADAPTER_FIB
3. It is possible to construct an attack via the SRB ioctls where
the user obtains assorted elevated privileges. Various approaches are
possible, the trivial ones being things like writing to the raw media
via scsi commands and the swap image of other executing programs with
higher privileges.
So the ioctls should be CAP_SYS_RAWIO - at least all the FIB manipulating
ones. This is a bandaid fix for #3 but probably the ioctls should grow
their own capable checks. The other two bugs need someone competent in that
driver to fix them.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If a battery is at a critical charge level and not being charged or
discharged, then the ACPI _BST method will return a state of 4, and
the current acpi_battery_get_property() code will not set any property
value for POWER_SUPPLY_PROP_STATUS. This will cause an oops in
power_supply_show_property() when it reads off the end of the
status_text array. This actually was causing a 100% reproducible
crash on boot on my laptop with two batteries, when one battery was
completely drained and the laptop was not plugged in.
Fix this by making sure acpi_battery_get_property() returns
POWER_SUPPLY_STATUS_UNKNOWN for any battery state it doesn't already
handle explicitly. There doesn't seem to be any status enum value
defined that makes more sense than 'unknown' for a battery at a
critical charge level.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <lenb@t61.(none)>
Got a panic in the threading code on an older kernel when the Adapter
failed to load properly and driver shut down apparently before any
threading had started, can not dupe. Expect that this may be relevant in
the latest kernel, but not sure. This patch does no harm, and should
alleviate the possibility of this panic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Noticed on PowerPC allmod config build:
drivers/scsi/aacraid/commsup.c:1342: warning: large integer implicitly truncated to unsigned type
drivers/scsi/aacraid/commsup.c:1343: warning: large integer implicitly truncated to unsigned type
drivers/scsi/aacraid/commsup.c:1344: warning: large integer implicitly truncated to unsigned type
Also fix some whitespace on the changed lines.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The code calling brightness_set() can't handle EINTR/ERESTARTSYS well, nor
is it checking brightness_set() return status properly.
Fix it.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Map an mutex_lock_interruptible() error return into ERESTARTSYS, as the
only possible error from mutex_lock_interruptible is EINTR, and that will
only happen if signal_pending() causes the mutex lock attempt to abort.
This still allows signals to be delivered ASAP, which is much nicer than
just doing mutex_lock, and still shadows userspace from EINTR when
SA_RESTART is active.
Problem reported by Peter Jordan.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Peter Jordan <usernetwork@gmx.info>
Cc: Richard Neill <rn214@hermes.cam.ac.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
The lm-sensors 3.0.0/libsensors4 compatibility changes are reason enough to
bump up the version string. Do it.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Newer Lenovo BIOSes support the standard ACPI backlight brightness
interface (_BCM, _BQC, _BCL). It should be used instead of the native
thinkpad backlight brightness control interface when possible.
This patch disables the native brightness support in the driver by default
when we detect that the standard ACPI interface is available. The local
admin can still enable it using the module parameter "brightness_enable".
Note that we need to detect the standard ACPI backlight interface only in
boxes for which we would load the native backlight interface in the first
place, and that no ThinkPad BIOS has _BCL but misses the other methods, so
the detection routines can be really simple.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a "brightness_enable" module parameter that allows the local admin to
force the backlight support to not be enabled.
It can also be used to force the backlight support to be enabled, but that
is currently a no-op as the backlight support is enabled by default when
available. This will be changed by a different patch.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Lenovo ThinkPads often have 16 brightness levels in EC, and not just eight
levels like older ThinkPads. They also have standard ACPI backlight
brightness control.
We detect the number of brightness levels by the presence of a BCLL package
with 16 entries. If BCLL is not there, we assume eight levels (Z6*). If
it is there, but it doesn't have 16 entries, we assume eight levels (T60).
Otherwise we assume sixteen levels (T61, X61, etc).
We don't use _BCL because it can have side-effects in thinkpads. Thanks to
Thomas Renninger <trenn@suse.de> for notifying me of this potential
problem.
Using the standard ACPI backlight brightness control *instead* of the
native thinkpad backlight control is a better idea, though. A different
patch will take care of this.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Revert commit fba956c46a, "Map volume and
brightness events on thinkpads".
That commit made some modifications to the default keymaps that cause bad
behaviour on all IBM ThinkPads if HAL doesn't know to change them into
passive (on-screen-display only) events.
The proper solution for IBM ThinkPads is to use the _NOTIFY version of the
key codes for the IBM default map (which are not available in mainline
yet), and for the Lenovo keymap, it will take some studying of the various
DSDTs and testing to know the best path (which I will do shortly).
For more data, refer to:
http://thread.gmane.org/gmane.linux.kernel/591037/focus=591045
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2007-11-05 13:07:10 -05:00
1329 changed files with 20952 additions and 18856 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
