* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata clear horkage on ata_dev_init()
[libata, IDE] add new VIA bridge to VIA PATA drivers
pata_it821x: fix lost interrupt with atapi devices
Fix broken pata_via cable detection
dev->horkage should be cleared over device hotunplug/plug. Clear it
in ata_dev_init().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The earlier crash dump fix on x86_64 depended on patches in -mm which
are intended for post-2.6.23. Without those, it broke the build when
it went into 2.6.23-rc5.
This changes the field references in ELF_CORE_COPY_REGS back to those
still used in mainline.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the case when an nmi gets stucks the endflag stays equal to zero.
This causes the busy looping on other cpus to continue, even though the
nmi test is done.
On my machine with out the change below the system would hang right
after check_nmi_watchdog(). The change below just sets endflag prior to
checking if the test was successful or not.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CLFLUSH for the modified code line in text_poke was supposed
to speed up CPU recovery. Unfortunately it seems to cause hangs
on some VIA C3s (at least on VIA Esther Model 10 Stepping 9)
Remove it.
Thanks to Stefan Becker for reporting/testing.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the NMI watchdog on Intel CoreDuo processor where the kernel would
get stuck during boot. The issue is related to errata AE49, where the
PERFEVTSEL1 counter does not have a working enable bit. Thus it is not
possible to use it for NMI.
The patch creates a dedicated wd_ops for CoreDuo which falls back to
using PERFEVTSEL0. The other Intel processors supporting the
architectural PMU will keep on using PERFEVTSEL1 as this allows other
subsystems, such as perfmon, to use PERFEVTSEL0 for PEBS monitoring in
particular. Bug initially reported by Daniel Walker.
AK: Added comments
Signed-off-by: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fsid_source decided where to get the 'fsid' number to
return for a GETATTR based on the type of filehandle.
It can be from the device, from the fsid, or from the
UUID.
It is possible for the filehandle to be inconsistent
with the export information, so make sure the export information
actually has the info implied by the value returned by
fsid_source.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Luiz Fernando N. Capitulino" <lcapitulino@gmail.com>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes in NFSd cause a directory which is mounted-on
to not appear properly when the filesystem containing it is exported.
*exp_get* now returns -ENOENT rather than NULL and when
commit 5d3dbbeaf5
removed the NULL checks, it didn't add a check for -ENOENT.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When PTRACE_SYSCALL was used and then PTRACE_DETACH is used, the
TIF_SYSCALL_TRACE flag is left set on the formerly-traced task. This
means that when a new tracer comes along and does PTRACE_ATTACH, it's
possible he gets a syscall tracing stop even though he's never used
PTRACE_SYSCALL. This happens if the task was in the middle of a system
call when the second PTRACE_ATTACH was done. The symptom is an
unexpected SIGTRAP when the tracer thinks that only SIGSTOP should have
been provoked by his ptrace calls so far.
A few machines already fixed this in ptrace_disable (i386, ia64, m68k).
But all other machines do not, and still have this bug. On x86_64, this
constitutes a regression in IA32 compatibility support.
Since all machines now use TIF_SYSCALL_TRACE for this, I put the
clearing of TIF_SYSCALL_TRACE in the generic ptrace_detach code rather
than adding it to every other machine's ptrace_disable.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix "lost" interrupt problem when using dma with CD/DVD drives in some
configurations. This problem can make installing linux from media
impossible for distro's that have switched to libata-only configurations.
The simple fix is to eliminate the use of dma for reading drive status, etc,
by checking the number of bytes to transferred.
This change will only affect the behavior of atapi devices, not disks.
There is more info at http://bugzilla.redhat.com/show_bug.cgi?id=242229
This patch is for 2.6.22.1
Signed-off-by: Jeff Norden <jnorden@math.tntech.edu>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ocelot: remove remaining bits
[MIPS] TLB: Fix instruction bitmasks
[MIPS] R10000: Fix wrong test in dma-default.c
[MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
[MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
[MIPS] Kconfig: whitespace cleanup.
[MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
[MIPS] BCM1480: Fix computation of interrupt mask address register.
[MIPS] i8259: Add disable method.
[MIPS] tty: add the new ioctls and definitions.
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-algo-bit: Read block data bugfix
i2c-pxa: Fix adapter number
i2c-gpio: Fix adapter number
Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()
[...]
on_each_cpu(do_drain, cachep, 1, 1);
check_irq_on();
[...]
may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, ibmebus derived a device's bus_id from its location code.
The location code is not guaranteed to be unique, so we might get bus_id
collisions if two devices share the same location code. The OFDT
full_name, however, is unique, so we use that instead (truncating it
on the left if it is too long).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PS3, A storage device may show up in the repository before the hypervisor
has finished probing:
- If its type is not yet known, it shows up as PS3_DEV_TYPE_STOR_DUMMY,
- If its regions are being probed, it shows up as having zero regions.
If any of these happen, consider the device not yet present. The storage
probe thread will retry later.
This fixes the timing-dependent problem where a kernel booted from FLASH ROM
sometimes cannot find the hard disk.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, running any SPE program on the ps3 will trigger a BUG_ON
when spufs_run_spu tries to clear the master run control bit, as lv1
does not make the master run control available to Linux.
This change makes SPE apps work again by disabling changes to the
master run control on PS3. Although we don't have the facility to
disable a SPE with supervisor-level privileges, it's better than
hitting the BUG_ON unconditionally.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered. The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.
The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared. This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch had the conditional inverted. This patch fixes it
so that we return the original position if it does not straddle a page.
Thanks to Bob Gilligan for spotting this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes a bug in the way i2c-algo-bit handles I2C_M_RECV_LEN,
used to implement i2c_smbus_read_block_data(). Previously, in the
absence of PEC (rarely used!) it would NAK the "length" byte:
S addr Rd [A] [length] NA
That prevents the subsequent data bytes from being read:
S addr Rd [A] [length] { A [data] }* NA
The primary fix just reorders two code blocks, so the length used
in the "should I NAK now?" check incorporates the data which it
just read from the slave device.
However, that move also highlighted other fault handling glitches.
This fixes those by abstracting the RX path ack/nak logic, so it
can be used in more than one location. Also, a few CodingStyle
issues were also resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c adapte. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that platform_device.id is a "u32" so testing it for being
nonnegative is useless when setting up an i2c bitbang device. Instead,
do what the platform_bus code does and test it against the value "-1".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in the I/O region declaration of two
hardware monitoring drivers (lm78 and w83781d.) We were requesting
one extra port at the end of the region.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The function blkcipher_get_spot tries to return a buffer of
the specified length that does not straddle a page. It has
an off-by-one bug so it may advance a page unnecessarily.
What's worse, one of its callers doesn't provide a buffer
that's sufficiently long for this operation.
This patch fixes both problems. Thanks to Bob Gilligan for
diagnosing this problem and providing a fix.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes (papers over) "Sleep problems with kernels >= 2.6.21 on powerpc",
http://lkml.org/lkml/2007/8/25/155. The issue is that the FireWire
controller's pci_dev.current_state of iBook G3 and presumably older
PowerBooks is still in PCI_UNKNOWN instead of PCI_D0 when the firewire
driver's .suspend method is called.
Like it was suggested earlier in http://lkml.org/lkml/2006/10/24/13, we
do not fail .suspend anymore if pci_set_power_state failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
fix ideal_runtime:
- do not scale it using niced_granularity()
it is against sum_exec_delta, so its wall-time, not fair-time.
- move the whole check into __check_preempt_curr_fair()
so that wakeup preemption can also benefit from the new logic.
this also results in code size reduction:
text data bss dec hex filename
13391 228 1204 14823 39e7 sched.o.before
13369 228 1204 14801 39d1 sched.o.after
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Second preparatory patch for fix-ideal runtime:
Mark prev_sum_exec_runtime at the beginning of our run, the same spot
that adds our wait period to wait_runtime. This seems a more natural
location to do this, and it also reduces the code a bit:
text data bss dec hex filename
13397 228 1204 14829 39ed sched.o.before
13391 228 1204 14823 39e7 sched.o.after
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Preparatory patch for fix-ideal-runtime:
simplify __check_preempt_curr_fair(): get rid of the integer return.
text data bss dec hex filename
13404 228 1204 14836 39f4 sched.o.before
13393 228 1204 14825 39e9 sched.o.after
functionality is unchanged.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the cfs_rq->wait_runtime debug/statistics counter was not maintained
properly - fix this.
this also removes some code:
text data bss dec hex filename
13420 228 1204 14852 3a04 sched.o.before
13404 228 1204 14836 39f4 sched.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
fix niced_granularity(). This resulted in under-scheduling for
CPU-bound negative nice level tasks (and this in turn caused
higher than necessary latencies in nice-0 tasks).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
First fix the check
if (*imbalance + SCHED_LOAD_SCALE_FUZZ < busiest_load_per_task)
with this
if (*imbalance < busiest_load_per_task)
As the current check is always false for nice 0 tasks (as
SCHED_LOAD_SCALE_FUZZ is same as busiest_load_per_task for nice 0
tasks).
With the above change, imbalance was getting reset to 0 in the corner
case condition, making the FUZZ logic fail. Fix it by not corrupting the
imbalance and change the imbalance, only when it finds that the HT/MC
optimization is needed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This git mod: 77e4635ae1
converted to a "greedy" allocation interface, but for the quota hashtables
it switched from allocating XFS_QM_HASHSIZE (nr of elements)
xfs_dqhash_t's to allocating only XFS_QM_HASHSIZE *bytes* - quite a lot
smaller! Then when we converted hsize "back" to nr of elements (the
division line) hsize went to 0. This was leading to oopses when running
any quota tests on the Fedora 8 test kernel, but the problem has been
there for almost a year.
SGI-PV: 968837
SGI-Modid: xfs-linux-melb:xfs-kern:29354a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
- in xfs_probe_cluster rename the inner len to pg_len. There's no harm
here because the outer len isn't used after the inner len comes into
existence but it keeps the code clean.
- in xfs_da_do_buf remove the inner i because they don't overlap
and they are both the same type.
SGI-PV: 968555
SGI-Modid: xfs-linux-melb:xfs-kern:29311a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
- remove the != 0 inside the unlikely in ASSERT_ALWAYS because sparse now
complains about comparisons between pointers and 0
- add a standalone ASSERT implementation because defining it to
ASSERT_ALWAYS means the string is expanded before the token passing
stringification. This way we get the actual content of the
assertion in the assfail message and don't overflow sparse's
stringification buffer leading to sparse error messages.
SGI-PV: 968555
SGI-Modid: xfs-linux-melb:xfs-kern:29310a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
We can't return a masked result of a __bitwise type. Compare it to 0 first
to keep the behaviour without the warning.
SGI-PV: 968555
SGI-Modid: xfs-linux-melb:xfs-kern:29309a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Sparse now warns about comparing pointers to 0, so change all instance
where that happens to NULL instead.
SGI-PV: 968555
SGI-Modid: xfs-linux-melb:xfs-kern:29308a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Apparently XEN does not keep the contents of the 48-bit gdt_48 data
structure that is passed to lgdt in the XEN machine state. Instead it
appears to save the _address_ of the 48-bit descriptor
somewhere. Unfortunately this data happens to reside on the stack and
is probably no longer availiable at the time of the actual protected
mode jump.
This is Xen bug but given that there is a one-line patch to work
around this problem, the linux kernel should probably do this. My fix
is to make the gdt_48 description in setup_gdt static (in setup_idt
this is already the case). This allows the kernel to boot under
Xen HVM again.
Signed-off-by: Christian Ehrhardt <lk@c--e.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
- Separate sys_call_table from arch/m32r/kernel/entry.S and
move it to arch/m32r/kernel/system_call.S.
- Change sys_call_table section from .data to .rodata.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
If no IRQ request is found in the IRQ check of ei_handler,
we can exit directly by jumping "restore_all", instead of via
"ret_from_intr".
This modification is also likely effective for IPI operations,
because scheduler call never happen at the exit of IPIs.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Simplify and clean up messy ei_handler code in arch/m32r/kernel/entry.S.
- Remove ifdef's for CONFIG_CHIP_* configulations.
- Rearrange the M32700 workaround code.
- Remove the messy platform-dependent interrupt check routines and
consolidate them to common INT0/INT1/INT2 check routines for all
platforms with cascaded interrupt controllers.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
On some m32r platforms, cascaded ICUs are used.
This patch is required to simplify ei_handler and consolidate platform-
dependent ICU check routines.
platform ICU/INT1 ICU/INT0 ICU/INT2
-------------- -------- -------- --------
m32104ut o - -
m32700ut o o o
opsput o o o
usrv o - -
(others) - - -
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Initialise s_flags in get_sb_mtd_aux() from the flags parameter.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I've bisected the deadlock when many small appends are done on jffs2 down to
this commit:
commit 6fe6900e1e
Author: Nick Piggin <npiggin@suse.de>
Date: Sun May 6 14:49:04 2007 -0700
mm: make read_cache_page synchronous
Ensure pages are uptodate after returning from read_cache_page, which allows
us to cut out most of the filesystem-internal PageUptodate calls.
I didn't have a great look down the call chains, but this appears to fixes 7
possible use-before uptodate in hfs, 2 in hfsplus, 1 in jfs, a few in
ecryptfs, 1 in jffs2, and a possible cleared data overwritten with readpage in
block2mtd. All depending on whether the filler is async and/or can return
with a !uptodate page.
It introduced a wait to read_cache_page, as well as a
read_cache_page_async function equivalent to the old read_cache_page
without any callers.
Switching jffs2_gc_fetch_page to read_cache_page_async for the old
behavior makes the deadlocks go away, but maybe reintroduces the
use-before-uptodate problem? I don't understand the mm/fs interaction
well enough to say.
[It's fine. dwmw2.]
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ryusuke Konishi says:
The recent truncate_complete_page() clears the dirty flag from a page
before calling a_ops->invalidatepage(),
^^^^^^
static void
truncate_complete_page(struct address_space *mapping, struct page *page)
{
...
cancel_dirty_page(page, PAGE_CACHE_SIZE); <--- Inserted here at
kernel 2.6.20
if (PagePrivate(page))
do_invalidatepage(page, 0); ---> will call
a_ops->invalidatepage()
...
}
and this is disturbing nfs_wb_page_priority() from calling
nfs_writepage_locked() that is expected to handle the pending
request (=nfs_page) associated with the page.
int nfs_wb_page_priority(struct inode *inode, struct page *page, int how)
{
...
if (clear_page_dirty_for_io(page)) {
ret = nfs_writepage_locked(page, &wbc);
if (ret < 0)
goto out;
}
...
}
Since truncate_complete_page() will get rid of the page after
a_ops->invalidatepage() returns, the request (=nfs_page) associated
with the page becomes a garbage in nfs_inode->nfs_page_tree.
------------------------
Fix this by ensuring that nfs_wb_page_priority() recognises that it may
also need to clear out non-dirty pages that have an nfs_page associated
with them.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
According to the mount(2) man page, the proper error return code for the
mount(2) system call when the special device name or the mounted-on
directory name is too long is ENAMETOOLONG.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Don't filter the return code from the in-kernel rpcbind or NFS mount
clients. Return the real error code so that callers of the new NFS
text-based mount API can apply a useful retry strategy.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The new text-based NFS mount option parsing logic doesn't recognize any
valid transport protocols due to a silly mistake in the protocol token
matching logic. This prevents basic mount requests such as:
mount.nfs server:/export /mnt -o proto=tcp
from working with the new text-based NFS mount API.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Doh! We can't use cancel_delayed_work_sync because we may have been called
from an unmount that was being performed by nfs_automount_task.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.
This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After my last patch we have a new header file for HP simulator use.
Here's code to use it for stuff that used to have `extern' statements
inline in the code. Functionality should not change with this patch.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch cleans up the `enable early console for SKI' patch
(471e7a4484), and
1. potentially allows the gensparse_defconfig to work again.
(there are other problems running a generic kernel on Ski)
2. fixes the `console registered twice' problem.
3. Cleans up the code by moving the `extern hpsim_cons' declaration to
a new asm/hpsim.h file.
Thanks to Jes for comments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When dumping memory via sysrq-m it is possible to take a bogus NMI watchdog
or softlockup watchdog because the dump can take a long time on big memory
systems.
Occasionally tickle the watchdog when doing the dump.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add additional support for CPU disable on SN platforms.
Correctly setup the smp_affinity mask for I/O error IRQs.
Restrict the use of the feature to Altix 4000 and 450 systems
running with a CPU disable capable PROM, and do not allow disabling
of CPU 0.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Avoid setting the value if the symbol doesn't need to be changed or can't
be changed. Later choices may change the dependencies and thus the
possible input range.
make oldconfig from a 2.6.22 .config with CONFIG_HOTPLUG_CPU not set
was in some configurations setting CONFIG_HOTPLUG_CPU=y without asking,
even when there was no actual requirement for CONFIG_HOTPLUG_CPU.
This was triggered by SUSPEND_SMP that does a select HOTPLUG_CPU.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Tested-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: SRQ fixes to enable IPoIB CM
IB/ehca: Fix Small QP regressions
This avoids the recent NFS mount regression (returning EBUSY when
mounting the same filesystem twice with different parameters).
The best I can do given the constraints appears to be to have the kernel
first look for a superblock that matches both the fsid and the
user-specified mount options, and then spawn off a new superblock if
that search fails.
Note that this is not the same as specifying nosharecache everywhere
since nosharecache will never attempt to match an existing superblock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Hua Zhong <hzhong@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lguest didn't initialize the kernel stack the way a real i386 kernel
does, and ended up triggering a corner-case in the stack frame checking
that doesn't happen on naive i386, and that the stack dumping didn't
handle quite right.
This makes the frame handling more correct, and tries to clarify the
code at the same time so that it's a bit more obvious what is going on.
Thanks to Rusty Russell for debugging the lguest failure-
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HPET clocksource in drivers/char/hpet.c was written as generic code
for ia64, but it is not yet ready to replace the native HPET clocksource
implementations that the i386/x86-64 architectures use.
On x86[-64], trying to register this clocksource results in potentially
multiple hpet-based clocksources being registered, and if the ia64 one
is chosen on x86_64 some users have experienced hangs.
Eventually all three architectures may end up using the same code, but
that is not the case right now.
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Paolo Ornati <ornati@fastwebnet.it>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
- cxgb3 engine microcode load
cxgb3 - Fix dev->priv usage
qeth: Drop ARP packages on HiperSockets interface with NOARP attribute.
qeth: provide specific message for OSA-adapters exclusively used
qeth: crash during reboot after failing online setting
qeth: Announce tx checksumming for qeth devices in TSO/EDDP mode
qeth: dont return the return values of void functions.
qeth: enforce a rate limit for inbound scatter gather messages
qeth: ungrouping a device must not be interruptible
netxen: fix crashes during module unload
netxen: Avoid firmware load in PCI probe
PS3: fix the bug that 'ifconfig down' would hang
IOC3: Program UART predividers.
Fix ehca SRQ support so that IPoIB connected mode works:
- Report max_srq > 0 if SRQ is supported
- Report "last wqe reached" asynchronous event when base QP dies;
this is required by the IB spec and IPoIB CM relies on receiving it
when cleaning up.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs. Fix them.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The VESA BIOS is specified to be register-clean. However, we have now
found at least one system which violates that. Thus, be as paranoid
about VESA calls as about everything else.
Huge thanks to Will Simoneau for reporting, diagnosing, and testing
this out on Dell Inspiron 5150.
Cc: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
sched: clean up task_new_fair()
sched: small schedstat fix
sched: fix wait_start_fair condition in update_stats_wait_end()
sched: call update_curr() in task_tick_fair()
sched: make the scheduler converge to the ideal latency
sched: fix sleeper bonus limit
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Bump driver versions
ata_piix: implement IOCFG bit18 quirk
libata: implement BROKEN_HPA horkage and apply it to affected drives
sata_promise: FastTrack TX4200 is a second-generation chip
pata_marvell: Add more identifiers
ata_piix: add Satellite U200 to broken suspend list
ata: add ATA_MWDMA* and ATA_SWDMA* defines
ata_piix: IDE mode SATA patch for Intel Tolapai
libata-core: Allow translation setting to fail
Load the engine microcode when an interface
is brought up, instead of of doing it when the module
is loaded.
Loosen up tight binding between the driver and the
engine microcode version.
There is no need for microcode update with T3A boards.
Fix the file naming.
Do a better job at logging the loading activity.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A network interface can get ARP packets even when the interface has
NOARP specified. In a HiperSockets environment this disturbs receiving
systems when packets are sent on the multicast queue. (E.g. TCP/IP on
z/VM issues messages reporting invalid data on the HiperSockets
interface.)
Qeth will no longer send ARP packets on HiperSockets interface when
interface has the NOARP attribute.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Exclusive usage of OSA-cards has been introduced. Even though Linux
does not make use of it, qeth should be prepared to receive a bad RC
for some initialization steps. A meaningful message is now given,
if an OSA-device is set online, even though the OSA-adapter is already
exclusively used by another host.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Online setting of a qeth device may fail for instance because of:
- out-of-memory condition when allocating qdio queues
- IDX ACTIVATE problem
- ...
Such a device is still returned in a driver_for_each_device loop
processed in qeth_reboot_event(), which calls
qeth_clear_qdio_buffers(). Make sure qeth_clear_output_buffer() is
called only, if the qdio queues have been successfully allocated
during initialization of a qeth device.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TSO requires tx checksumming. For non GSO frames in TSO/EDDP mode we
have to manually calculate the checksum.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
under memory pressure scatter gather mode switching messages must be
rate limited.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Problem:
A recovery thread must not be active when device is removed.
In qeth_remove_device() an interruptible wait operation is used
to wait until a qeth recovery thread is finished. If a user really
interrupts the ungroup operation of a qeth device while a recovery
is running, cio and qeth are out of sync (device already removed
from cio, but kept in qeth). A following module unload of qeth
results in a kernel OOPS here.
Solution:
Do not allow interruption of ungroup operation to guarantee
finishing of a potentially running qeth recovery thread.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot. This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register. This happens
to work for the console but not rarely for additional ports.
While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Page migration currently does not check if the target of the move contains
nodes that that are invalid (if root attempts to migrate pages)
and may try to allocate from invalid nodes if these are specified
leading to oopses.
Return -EINVAL if an offline node is specified.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For hugepage mappings, the file offset, like the address and size, needs to
be aligned to the size of a hugepage.
In commit 68589bc353, the check for this was
moved into prepare_hugepage_range() along with the address and size checks.
But since BenH's rework of the get_unmapped_area() paths leading up to
commit 4b1d89290b, prepare_hugepage_range()
is only called for MAP_FIXED mappings, not for other mappings. This means
we're no longer ever checking for an aligned offset - I've confirmed that
mmap() will (apparently) succeed with a misaligned offset on both powerpc
and i386 at least.
This patch restores the check, removing it from prepare_hugepage_range()
and putting it back into hugetlbfs_file_mmap(). I'm putting it there,
rather than in the get_unmapped_area() path so it only needs to go in one
place, than separately in the half-dozen or so arch-specific
implementations of hugetlb_get_unmapped_area().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We find that SB700 and SB800 use the same SMBus device ID as SB600, which is
0x4385, instead of the already submitted 0x4395.
Besides removing the wrong SB700 device ID, add SB800 support to kernel, by
renaming the PCI_DEVICE_ID_ATI_IXP600_SMBUS into
PCI_DEVICE_ID_ATI_SBX00_SMBUS.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Spotted by taoyue <yue.tao@windriver.com> and Jeremy Katz <jeremy.katz@windriver.com>.
collect_signal: sigqueue_free:
list_del_init(&first->list);
if (!list_empty(&q->list)) {
// not taken
}
q->flags &= ~SIGQUEUE_PREALLOC;
__sigqueue_free(first); __sigqueue_free(q);
Now, __sigqueue_free() is called twice on the same "struct sigqueue" with the
obviously bad implications.
In particular, this double free breaks the array_cache->avail logic, so the
same sigqueue could be "allocated" twice, and the bug can manifest itself via
the "impossible" BUG_ON(!SIGQUEUE_PREALLOC) in sigqueue_free/send_sigqueue.
Hopefully this can explain these mysterious bug-reports, see
http://marc.info/?t=118766926500003http://marc.info/?t=118466273000005
Alexey Dobriyan reports this patch makes the difference for the testcase, but
nobody has an access to the application which opened the problems originally.
Also, this patch removes tasklist lock/unlock, ->siglock is enough.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: taoyue <yue.tao@windriver.com>
Cc: Jeremy Katz <jeremy.katz@windriver.com>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mariusz Kozlowski reported lockdep's warning:
> =================================
> [ INFO: inconsistent lock state ]
> 2.6.23-rc2-mm1 #7
> ---------------------------------
> inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
> ifconfig/5492 [HC0[0]:SC0[0]:HE1:SE1] takes:
> (&tp->lock){+...}, at: [<de8706e0>] rtl8139_interrupt+0x27/0x46b [8139too]
> {in-hardirq-W} state was registered at:
> [<c0138eeb>] __lock_acquire+0x949/0x11ac
> [<c01397e7>] lock_acquire+0x99/0xb2
> [<c0452ff3>] _spin_lock+0x35/0x42
> [<de8706e0>] rtl8139_interrupt+0x27/0x46b [8139too]
> [<c0147a5d>] handle_IRQ_event+0x28/0x59
> [<c01493ca>] handle_level_irq+0xad/0x10b
> [<c0105a13>] do_IRQ+0x93/0xd0
> [<c010441e>] common_interrupt+0x2e/0x34
...
> other info that might help us debug this:
> 1 lock held by ifconfig/5492:
> #0: (rtnl_mutex){--..}, at: [<c0451778>] mutex_lock+0x1c/0x1f
>
> stack backtrace:
...
> [<c0452ff3>] _spin_lock+0x35/0x42
> [<de8706e0>] rtl8139_interrupt+0x27/0x46b [8139too]
> [<c01480fd>] free_irq+0x11b/0x146
> [<de871d59>] rtl8139_close+0x8a/0x14a [8139too]
> [<c03bde63>] dev_close+0x57/0x74
...
This shows that a driver's irq handler was running both in hard interrupt
and process contexts with irqs enabled. The latter was done during
free_irq() call and was possible only with CONFIG_DEBUG_SHIRQ enabled.
This was fixed by another patch.
But similar problem is possible with request_irq(): any locks taken from
irq handler could be vulnerable - especially with soft interrupts. This
patch fixes it by disabling local interrupts during handler's run. (It
seems, disabling softirqs should be enough, but it needs more checking
on possible races or other special cases).
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will avoid a possible fault in ecryptfs_sync_page().
In the function, eCryptfs calls sync_page() method of a lower filesystem
without checking its existence. However, there are many filesystems that
don't have this method including network filesystems such as NFS, AFS, and
so forth. They may fail when an eCryptfs page is waiting for lock.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IOC3 is a multifunction device but not in sense of the PCI
specification. Currently its ethernet and serial functionality are
supported by two separate drivers authored and maintained by different
people, so MAINTAINERS should reflect that.
Cc: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dependencies of CONFIG_SUSPEND and CONFIG_HIBERNATION introduced by commit
296699de6b "Introduce CONFIG_SUSPEND for
suspend-to-Ram and standby" are incorrect, as they don't cover the facts that
(1) not all architectures support suspend and (2) SMP hibernation is only
possible on X86 and PPC64 (if CONFIG_PPC64_SWSUSP is set).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not BUG() if we cannot register a slab with sysfs. Just print an error.
The only consequence of not registering is that the slab cache is not
visible via /sys/slab. A BUG() may not be visible that early during boot
and we have had multiple issues here already.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update various SPI drivers so they properly support
- coldplug through "modprobe $(cat /sys/devices/.../modalias)"
- hotplug through "modprobe $(MODALIAS)"
The basic rule for platform, SPI, and (new style) I2C drivers is just
to make sure that modprobing the driver name works. In this case, all
the relevant drivers are platform drivers, and this patch either
(a) Changes the driver name, if no in-tree code would break;
this is simpler and thus preferable in the long term.
(b) Adds MODULE_ALIAS directives, when in-tree platforms declare
devices using the current driver name; less desirable.
Most systems will link SPI controller drivers statically, but
there's no point in being needlessly broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
taskstats.ac_exitcode is assigned to task_struct.exit_code in bacct_add_tsk()
through the following kernel function calls:
do_exit()
taskstats_exit()
fill_pid()
bacct_add_tsk()
The problem is that in do_exit(), task_struct.exit_code is set to 'code' only
after taskstats_exit() has been called. So we need to move the assignment
before taskstats_exit().
Signed-off-by: Jonathan Lim <jlim@sgi.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix possible NULL pointer dereference when freeing blocks in case table of
free space is used. Also fix handling of the case when we need to move
extent from one block to another one to make space for indirect extent.
BTW: Nobody seem to have ever used this code.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If UDF superblock is incorrect, we can fail to find a table of free /
allocated space and consequently Oops. Handle this situation more
gracefully by ignoring the broken UDF partition.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In migration fallback path, write_page() or lock_page() will be called.
This causes sleep with holding rcu_read_lock().
For avoding that, just do rcu_lock if the page is Anon.(this is enough.)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stop UML crashing when trying to dump a process core on x86_64. This is the
minimal fix to stop the crash - more things are broken here, and patches are
forthcoming.
The immediate thing to do is define ELF_CORE_COPY_REGS and
ELF_CORE_COPY_FPREGS. Defining ELF_CORE_COPY_FPREGS allows dump_fpu to go
away. It is defined in terms of save_fp_registers, so that needs to be added.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drives choke on READ_NATIVE_MAX_ADDRESS[_EXT]. Implement
ATA_HORKAGE_BROKEN_HPA and apply it to affected drives.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch corrects sata_promise to classify FastTrack TX4200
(DID 3515/3519) as a second-generation chip. Promise's partial-
source FT TX4200 driver confirms this classification.
Treating it as a first-generation chip causes several problems:
1. Detection failures. This is a recent regression triggered by
the hotplug-enabling changes in 2.6.23-rc1.
2. Various "failed to resume link for reset" warnings.
This patch fixes <http://bugzilla.kernel.org/show_bug.cgi?id=8936>.
Thanks to Stephen Ziemba for reporting the bug and for testing the fix.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Stephen Ziemba <sziemba@ecn.purdue.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some compilers (especially older gcc releases) may skip inlining
sometimes which will lead to link failures. Force the inlining of
keyfunctions in slub_def.h to avoid these issues.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Jan Dittmer <jdi@l4x.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Satellite U200 also shares the problem. Add it to the broken suspend
list. Original patch from John Schember.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: John Schember <john@nachtimwald.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix several bugs in MSI handling.
[SPARC64]: Fix type and constant sizes wrt. sun4u IMAP/ICLR handling.
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[PKTGEN]: Remove write-only variable.
[NETFILTER]: xt_tcpudp: fix wrong struct in udp_checkentry
[NET_SCHED] sch_prio.c: remove duplicate call of tc_classify()
[BRIDGE]: Fix OOPS when bridging device without ethtool.
[BRIDGE]: Packets leaking out of disabled/blocked ports.
[TCP]: Allow minimum RTO to be configurable via routing metrics.
SCTP: Fix to handle invalid parameter length correctly
SCTP: Abort on COOKIE-ECHO if backlog is exceeded.
SCTP: Correctly disable listening when backlog is 0.
SCTP: Do not retransmit chunks that are newer then rtt.
SCTP: Uncomfirmed transports can't become Inactive
SCTP: Pick the correct port when binding to 0.
SCTP: Use net_ratelimit to suppress error messages print too fast
SCTP: Fix to encode PROTOCOL VIOLATION error cause correctly
SCTP: Fix sctp_addto_chunk() to add pad with correct length
SCTP: Assign stream sequence numbers to the entire message
SCTP: properly clean up fragment and ordering queues during FWD-TSN.
[PKTGEN]: Fix multiqueue oops.
[BNX2]: Add write posting comment.
[BNX2]: Use msleep().
Resend trying to remove 8-bit characters in the email.
This patch adds the Intel Tolapai IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some early drives (pre ATA1) this feature is not supported. If it
fails then we know the drive geometry is the hardware geometry and the
one we tried to set anyway so just carry on.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1) sun4{u,v}_build_msi() have improper return value handling.
We should always return negative error codes, instead of
using the magic value "0" which could in fact be a valid
MSI number.
2) sun4{u,v}_build_msi() should return -ENOMEM instead of
calling prom_prom() halt with kzalloc() of the interrupt
data fails.
3) We 'remembered' the MSI number using a singleton in the
struct device archdata area, this doesn't work for MSI-X
which can cause multiple MSIs assosciated with one device.
Delete that archdata member, and instead store the MSI
number in the IRQ chip data area.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen_thread.pid is set to current->pid and is never used
after this. So remove this at all.
Found during isolating the explicit pid/tgid usage.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem to have any effect on the x86 architecture but it does
have effect on the Axis CRIS architecture.
Signed-off-by: Jesper Bengtsson <jesper.bengtsson@axis.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_CLS_ACT is enabled, tc_classify() is called twice in
prio_classify(). This causes "interesting" behaviour: with the setup
below, packets are duplicated, sent twice to ifb0, and then loop in and
out of ifb0.
The patch uses the previously calculated return value in the switch,
which is probably what Patrick had in mind in commit
bdba91ec70 -- maybe Patrick can
double-check this?
-- example setup --
ifconfig ifb0 up
tc qdisc add dev ifb0 root netem delay 2s
tc qdisc add dev $ETH root handle 1: prio
tc filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 172.24.110.6/32 flowid 1:1 \
action mirred egress redirect dev ifb0
ping -c1 172.24.110.6
Signed-off-by: Lucas Nussbaum <lucas.nussbaum@imag.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge code calls ethtool to get speed. The conversion to using
only ethtool_ops broke the case of devices without ethtool_ops.
This is a new regression in 2.6.23.
Rearranged the switch to a logical order, and use gcc initializer.
Ps: speed should have been part of the network device structure from
the start rather than burying it in ethtool.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some packet leakage in bridge. The bridging code was
allowing forward table entries to be generated even if a device was
being blocked. The fix is to not add forwarding database entries
unless the port is active.
The bug arose as part of the conversion to processing STP frames
through normal receive path (in 2.6.17).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cell phone networks do link layer retransmissions and other
things that cause unnecessary timeout retransmits. So allow
the minimum RTO to be inflated per-route to deal with this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan reports that maxcpus=1 is still broken in 2.6.23-rc4:
if CONFIG_HOTPLUG_CPU is not set, x86_64 bootup oopses in show_stat() -
for_each_possible_cpu accesses a per-cpu area which was never set up.
Alexey identified commit 61ec7567db
(ACPI: boot correctly with "nosmp" or "maxcpus=0") as the origin;
but it's not really to blame, just exposes a bug in 2.6.23-rc1's commit
8b3b295502 (Especially when !CONFIG_HOTPLUG_CPU,
avoid needlessy allocating resources for CPUs that can never become available).
rc1's test for max_cpus < 2 in start_kernel() wasn't working because
max_cpus was still NR_CPUS at that point: until rc4 moved the maxcpus
parsing earlier. Now it sets cpu_possible_map to 1 before allocating
all possible per-cpu areas; then smp_init() expands cpu_possible_map
to cpu_present_map (0xf in my case) later on.
rc1's commit has good intentions, but expects cpu_present_map to be
limited by maxcpus, which is only the case on i386. cpus_and(possible,
possible,present) might be good, but needs an audit of cpu_present_map
uses - there may well be assumptions that any cpu present is possible.
So stay safe for now and just revert those #ifndef CONFIG_HOTPLUG_CPU
optimizations in rc1's commit.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an INIT with invalid parameter length look like this:
Parameter Type : 1
Parameter Length: 800
and not contain any payload, SCTP will ignore this parameter and send
back a INIT-ACK.
This patch is fix to handle this invalid parameter length correctly.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Currently we abort on the INIT chunk we our backlog is currenlty
exceeded. Delay this about untill COOKIE-ECHO to give the user
time to accept the socket. Also, make sure that we treat
sk_max_backlog of 0 as no connections allowed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When performing a retransmit, do not include the chunk if
it was sent less then 1 rtt ago. The reason is that we
may receive the SACK very soon and wouldn't retransmit.
Suggested by Randy Stewart.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Do not set Unconfirmed transports to Inactive state. This may
result in an inactive association being destroyed since we start
counting errors on "inactive" transports against the association.
This was found at the SCTP interop event.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
sctp_bindx() allows the use of unspecified port. The problem is
that every address we bind to ends up selecting a new port if
the user specified port 0. This patch allows re-use of the
already selected port when the port from bindx was 0.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When multi bundling SHUTDOWN-ACK message is received in ESTAB state,
this will cause "sctp protocol violation state" message print many times.
If SHUTDOWN-ACK is bundled 300 times in one packet, message will be
print 300 times. The same problem also exists when received unexpected
HEARTBEAT-ACK message which is bundled message times.
This patch used net_ratelimit() to suppress error messages print too fast.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
PROTOCOL VIOLATION error cause in ABORT is bad encode when make abort
chunk. When SCTP encode ABORT chunk with PROTOCOL VIOLATION error cause,
it just add the error messages to PROTOCOL VIOLATION error cause, the
rest four bytes(struct sctp_paramhdr) is just add to the chunk, not
change the length of error cause. This cause the ABORT chunk to be a bad
format. The chunk is like this:
ABORT chunk
Chunk type: ABORT (6)
Chunk flags: 0x00
Chunk length: 72 (*1)
Protocol violation cause
Cause code: Protocol violation (0x000d)
Cause length: 62 (*2)
Cause information: 5468652063756D756C61746976652074736E2061636B2062...
Cause padding: 0000
[Needless] 00030010
Chunk Length(*1) = 72 but Cause length(*2) only 62, not include the
extend 4 bytes.
((72 - sizeof(chunk_hdr)) = 68) != (62 +3) / 4 * 4
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] PS3: Fix bug where the major version part is not compared
[POWERPC] Update defconfigs
[POWERPC] spufs: Don't call spu_run_init from spu_reacquire_runnable
[POWERPC] spufs: Fix update of mailbox status register during backed wbox write
[POWERPC] spu_manage: fix spu_unit_number for celleb device tree
[POWERPC] Update defconfigs
[POWERPC] Flush registers to proper task context
If the stack pointer is 0xc057a000, then the first stack page is at
0xc0579000 (the stack pointer is decremented before use). Not
calculating this correctly caused guests with CONFIG_DEBUG_PAGEALLOC=y
to be killed with a "bad stack page" message: the initial kernel stack
was just proceeding the .smp_locks section which
CONFIG_DEBUG_PAGEALLOC marks read-only when freeing.
Thanks to Frederik Deweerdt for the bug report!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At function sctp_addto_chunk(), it do pad before add payload to chunk if
chunk length is not 4-byte alignment. But it do pad with a bad length.
This patch fixed this probleam.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU. A potentially
outdated NPC value was being (re)written to the SPU.
So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.
This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.
This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The dummy touchkit_ps2_detect() for the CONFIG_MOUSE_PS2_TOUCHKIT=n case
shouldn't be a global function.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should not return IRQ_HANDLED if we didn't handle the interrupt.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.
IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.
However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.
Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Currently we only assign the sequence number to a packet that
we are about to transmit. This however breaks the Partial
Reliability extensions, because it's possible for us to
never transmit a packet, i.e. it expires before we get to send
it. In such cases, if the message contained multiple SCTP
fragments, and we did manage to send the first part of the
message, the Stream sequence numbers would get into invalid
state and cause receiver to stall.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When we recieve a FWD-TSN (meaning the peer has abandoned the data),
we need to clean up any partially received messages that may be
hanging out on the re-assembly or re-ordering queues. This is
a MUST requirement that was not properly done before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com.>
When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.
Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.
This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pending interrupts can be remaining at boot up time on some
platform. This will cause spurious interrupts when interrupt is
enabled for the first time. This patch clears IVR at the CPU
initialization to eliminate such spurious interrupts.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix handling for spurious interrupts not being mapped to any IRQs.
Currently, spurious interrupts that are not mapped to any IRQs are
handled as IRQ 15 (== IA64_SPURIOUS_VECTOR). But it is not proper
because vector != irq. We need special handlings for such spurious
interrupts not being mapped to any IRQs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Initially pkt_dev can be NULL this causes netif_subqueue_stopped to
oops. The patch below should cure it. But maybe the pktgen TX logic
should be reworked to better support the new multiqueue support.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comment to explain why we cannot read back after chip reset
before delaying.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bnx2.c (incorrectly) sets current->state directly to
TASK_UNINTERRUPTIBLE, without going through set_task_state(). However
all the code wants to do is an msleep so just make it do that instead...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cleanup: we have the 'se' and 'curr' entity-pointers already,
no need to use p->se and current->se.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mike Galbraith <efault@gmx.de>
small schedstat fix: the cfs_rq->wait_runtime 'sum of all runtimes'
statistics counters missed newly forked tasks and thus had a constant
negative skew. Fix this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Peter Zijlstra noticed the following bug in SCHED_FEAT_SKIP_INITIAL (which
is disabled by default at the moment): it relies on se.wait_start_fair
being 0 while update_stats_wait_end() did not recognize a 0 value,
so instead of 'skipping' the initial interval we gave the new child
a maximum boost of +runtime-limit ...
(No impact on the default kernel, but nice to fix for completeness.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mike Galbraith <efault@gmx.de>
update the fair-clock before using it for the key value.
[ mingo@elte.hu: small cleanups. ]
Signed-off-by: Ting Yang <tingy@cs.umass.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
de-HZ-ification of the granularity defaults unearthed a pre-existing
property of CFS: while it correctly converges to the granularity goal,
it does not prevent run-time fluctuations in the range of
[-gran ... 0 ... +gran].
With the increase of the granularity due to the removal of HZ
dependencies, this becomes visible in chew-max output (with 5 tasks
running):
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
out: 27 . 27. 32 | flu: 0 . 0 | ran: 17 . 13 | per: 44 . 40
out: 27 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 36 . 40
out: 29 . 27. 32 | flu: 2 . 0 | ran: 17 . 13 | per: 46 . 40
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
out: 29 . 27. 32 | flu: 0 . 0 | ran: 18 . 13 | per: 47 . 40
out: 28 . 27. 32 | flu: 0 . 0 | ran: 9 . 13 | per: 37 . 40
average slice is the ideal 13 msecs and the period is picture-perfect 40
msecs. But the 'ran' field fluctuates around 13.33 msecs and there's no
mechanism in CFS to keep that from happening: it's a perfectly valid
solution that CFS finds.
to fix this we add a granularity/preemption rule that knows about
the "target latency", which makes tasks that run longer than the ideal
latency run a bit less. The simplest approach is to simply decrease the
preemption granularity when a task overruns its ideal latency. For this
we have to track how much the task executed since its last preemption.
( this adds a new field to task_struct, but we can eliminate that
overhead in 2.6.24 by putting all the scheduler timestamps into an
anonymous union. )
with this change in place, chew-max output is fluctuation-less all
around:
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 2 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 1 | ran: 13 . 13 | per: 41 . 40
out: 28 . 27. 39 | flu: 0 . 1 | ran: 13 . 13 | per: 41 . 40
this patch has no impact on any fastpath or on any globally observable
scheduling property. (unless you have sharp enough eyes to see
millisecond-level ruckles in glxgears smoothness :-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mike Galbraith <efault@gmx.de>
There is an Amarok song switch time increase (regression) under
hefty load.
What is happening is that sleeper_bonus is never consumed, and only
rarely goes below runtime_limit, so for the most part, Amarok isn't
getting any bonus at all. We're keeping sleeper_bonus right at
runtime_limit (sched_latency == sched_runtime_limit == 40ms) forever, ie
we don't consume if we're lower that that, and don't add if we're above
it. One Amarok thread waking (or anybody else) will push us past the
threshold, so the next thread waking gets nada, but will reap pain from
the previous thread waking until we drop back to runtime_limit. It
looks to me like under load, some random task gets a bonus, and
everybody else pays, whether deserving or not.
This diff fixed the regression for me at any load rate.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Without this, we get qla2xxx complaining about "ISP System Error".
What's happening here is the firmware is detecting a Xfer-ready from the
storage when in fact the data-direction for a mode-select should be a
write (DATA_OUT).
The following patch fixes the problem (typo). Verified by Brian, as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Verified-by: Brian De Wolf <bldewolf@csupomona.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Make flush_tlb_kernel_range() an inline function.
[SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
[SPARC32]: Kill unused vars and macros from prom/console.c
[SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
[VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
[SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Mark Paul Moore as maintainer of labelled networking.
[VLAN/BRIDGE]: Fix "skb_pull_rcsum - Fatal exception in interrupt"
[ISDN]: Get rid of some pointless allocation casts in common and bsd comp.
[NET]: Avoid pointless allocation casts in BSD compression module
[IRDA]: Do not do pointless kmalloc return value cast in KingSun driver
[NET]: Fix crash in dev_mc_sync()/dev_mc_unsync()
[PPPOL2TP]: Fix endianness annotations.
[IOAT]: ioatdma needs to to play nice in a multi-dma-client world
[SLIP]: trivial sparse warning fix
[EQL]: sparse warning fix
[NET]: is_power_of_2 in net/core/neighbour.c
[TCP]: Describe tcp_init_cwnd() thoroughly in a comment.
[NET]: Fix IP_ADD/DROP_MEMBERSHIP to handle only connectionless
[KBUILD]: Sanitize tc_ematch headers.
[IPSEC] AH4: Update IPv4 options handling to conform to RFC 4302.
Fix bogus DEBUG_PREEMPT warning on x86_64, when cpu brought online after
bootup: current_is_keventd is right to note its use of smp_processor_id
is preempt-safe, but should use raw_smp_processor_id to avoid the warning.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sigh. Again an ACPI assault on the Thinkpad's Fn+F4 to suspend to RAM.
The default and text for CONFIG_THINKPAD_ACPI_INPUT_ENABLED were fixed
in -rc3, but now commit 14e04fb34f ("ACPI:
Schedule /proc/acpi/event for removal") introduces the ACPI_PROC_EVENT
config entry, and defaults it to 'n' to disable it again.
Change default to y, and add comment to make it clearer that n is for
future distros.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 61ec7567db ('ACPI: boot correctly
with "nosmp" or "maxcpus=0"') broke 'maxcpus=' handling on x86[-64].
maxcpus=N is now having no effect on x86_64, and freezing bootup on i386
(because of inconsistency with the separate maxcpus parsing down in
arch/i386, I guess). That's because early_param parsing is a little
different from __setup parsing, and needs the "=" omitted: then it seems
to work as the original commit intended (no mention of IO-APIC in
/proc/interrupts when maxcpus=0).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix SLB initialization at boot time
[POWERPC] Fix undefined reference to device_power_up/resume
[POWERPC] cell: Update cell_defconfig for 2.6.23
[POWERPC] axonram: Do not delete gendisks queue in error path
[POWERPC] axonram: Module modification for latest firmware API changes
[POWERPC] cell: Support pinhole-reset on IBM cell blades
[POWERPC] spu_manage: Use newer physical-id attribute
[POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] Add NOTES section
[PARISC] Use compat_sys_getdents
[PARISC] Do not allow STI_CONSOLE to be modular
[PARISC] Clean up sti_flush
[PARISC] Add dummy isa_(bus|virt)_to_(virt|bus) inlines
[PARISC] Add empty <asm-parisc/vga.h>
Bisected bizarre kernel-space nullptr dereference in udev to commit
18991197b4, adding the NOTES section fixes
it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
sti_flush is supposed to flush the caches so we can execute the STI rom
we copied to memory. Anything more than flush_icache_range is overkill.
Fixes a missing symbol when built as a module.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Less painful than fixing up the Kconfig for a pile of drivers to only build
on X86 && ARM && MIPS...
Just make them BUG(), as defining them to be 1:1 with physical memory will
likely HPMC the box anyways.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This avoids unused variable warnings in places like mm/vmalloc.c:
mm/vmalloc.c: In function ‘unmap_kernel_range’:
mm/vmalloc.c:75: warning: unused variable ‘start’
caused by it previously being a macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
resource_size_t can be either a u64 or a u32, and we can't
really know for sure, so when printing such a value out
always use long-long printf formatting and cast the argument
to that type.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just give a normal kernel log message of the problem and
return failure.
Based upon a patch from Mark Fortescue.
Signed-off-by: David S. Miller <davem@davemloft.net>
While debugging issues with the VDS server I made the
driver use partition 2 to get at the whole disk since
this is the "whole disk" partition in the Sun disk
label.
We really should use slice 0xff which really means
the whole physical disk in the VIO disk protocol.
Otherwise things won't work well on a disk image
that doesn't have a proper disk label on it.
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to preserve bridging code as it was before, but logic is quite
strange - I think we should free skb on error, since it is already
unshared and thus will just leak.
Herbert Xu states:
> + if ((skb = skb_share_check(skb, GFP_ATOMIC)) == NULL)
> + goto out;
If this happens it'll be a double-free on skb since we'll
return NF_DROP which makes the caller free it too.
We could return NF_STOLEN to prevent that but I'm not sure
whether that's correct netfilter semantics. Patrick, could
you please make a call on this?
Patrick McHardy states:
NF_STOLEN should work fine here.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc() returns a void pointer - no need to cast the return value.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The general kernel memory allocation functions return void pointers
and there is no need to cast their return values.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc() returns a void pointer, so there is no need to cast it in
drivers/net/irda/kingsun-sir.c::kingsun_probe().
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a crash that may occur when the routine dev_mc_sync()
deletes an address from the list it is currently going through. It
saves the pointer to the next element before deleting the current one.
The problem may also exist in dev_mc_unsync().
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
{s,d}_{session,tunnel} in pppol2tp_addr are actually host-endian
everywhere. We might switch them to net-endian, of course, but
that structure is exposed to userland via getname...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DMA engine has a multi-client interface, fix the ioatdma
driver to play along. At the same time, remove a couple of unnecessary
reads and writes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing n & (n - 1) for power of 2 check by is_power_of_2(n)
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People often get tripped up by this function and think that
it does not implemented the prescribed algorithms from
RFC2414 and RFC3390, even though it does.
So add a comment to head off such misunderstandings in the
future.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix IP[V6]_ADD_MEMBERSHIP and IP[V6]_DROP_MEMBERSHIP to
return -EPROTO for connection oriented sockets.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The headers in tc_ematch are used by iproute2, so these headers should
be processed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing our ESP/AH offload hardware, I discovered an issue with how
AH handles mutable fields in IPv4. RFC 4302 (AH) states the following
on the subject:
For IPv4, the entire option is viewed as a unit; so even
though the type and length fields within most options are immutable
in transit, if an option is classified as mutable, the entire option
is zeroed for ICV computation purposes.
The current implementation does not zero the type and length fields,
resulting in authentication failures when communicating with hosts
that do (i.e. FreeBSD).
I have tested record route and timestamp options (ping -R and ping -T)
on a small network involving Windows XP, FreeBSD 6.2, and Linux hosts,
with one router. In the presence of these options, the FreeBSD and
Linux hosts (with the patch or with the hardware) can communicate.
The Windows XP host simply fails to accept these packets with or
without the patch.
I have also been trying to test source routing options (using
traceroute -g), but haven't had much luck getting this option to work
*without* AH, let alone with.
Signed-off-by: Nick Bowler <nbowler@ellipticsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
shutdown_bridge_irq disconnects the irq so we need to connect the irq or
requesting the same irq a send time will fail. This used to make
things like ifconfig eth0 down; ifconfig eth0 up fail on IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain 32-bit kernel configurations seem to be able to cause references,
this was observed with gcc 4.1.2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The appended patch adds code to update siginfo_t's si_code field. It
fixes e.g. a floating point overflow regression in the SBCL testsuite.
Signed-off-By: Thiemo Seufer <ths@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also removes the while(1); loop by propagating the ATTRIB_NORET of die()
to nmi_exception_handler.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/traps.o
arch/mips/kernel/traps.c: In function 'show_backtrace':
arch/mips/kernel/traps.c:110: warning: unused variable 'ra'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS doesn't do CPU hotplugging yet but since many of the functions don't
even have an __init let's fix this right.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leaving these sections is useful to some tools that look at the image, and
none of them are loaded into memory. The .mdebug.abi64 section, in
particular, lets GDB recognize vmlinux.32 as an N64 program instead of
guessing that it is O32.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed since the Sibyte serial driver was exchanged.
Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the generation of asm-offset.h to work these need to be evaulatable
by gcc as a constant expression. This issue did exist for a while but
didn't bite because they're only in asm-offset.h for debugging purposes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
runtime limit and wakeup granularity used to be a function of
granularity and that was incorrect changed to sched_latency.
Fix this to make wakeup granularity a function of min-granularity,
and the runtime limit equal to latency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Add ref-counting for sbp2 orbs (fix command abortion)
firewire: fix unloading of fw-ohci while devices are attached
ieee1394: sbp2: fix sbp2_remove_device for error cases
due to adaptive granularity scheduling the role of sched_granularity
has changed to "minimum granularity", so rename the variable (and the
tunable) accordingly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Instead of specifying the preemption granularity, specify the wanted
latency. By fixing the granlarity to a constany the wakeup latency
it a function of the number of running tasks on the rq.
Invert this relation.
sysctl_sched_granularity becomes a minimum for the dynamic granularity
computed from the new sysctl_sched_latency.
Then use this latency to do more intelligent granularity decisions: if
there are fewer tasks running then we can schedule coarser. This helps
performance while still always keeping the latency target.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the lockdep sysctls not depend on CONFIG_SCHED_DEBUG.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This handles the case where we get the status write before getting the
complete_transaction callback ("status write for unknown orb"). In
this case, we just assume that the initial orb pointer transaction
succeeded and finish the orb. To prevent the transaction callback
from touching freed memory, we ref-count the orb structures.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix panic in run_timer_softirq right after "modprobe -r firewire-ohci"
if a FireWire disk was attached and firewire-sbp2 loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bug found by Olaf Hering <olh@suse.de>:
sbp2util_remove_command_orb_pool requires a valid lu->hi pointer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: balance ioremap checks
agp: Add device id for P4M900 to via-agp module
efficeon-agp leaks 'struct agp_bridge_data' in error paths of agp_efficeon_probe()
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: ioremap return value checks
drm/via: Fix dmablit when blit queue is full
drm_rmmap_ioctl(): remove dead code
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
myri10ge: update driver version to 1.3.2-1.269
myri10ge: use pcie_get/set_readrq
ehea: fix queue destructor
ehea: fix module parameter description
ehea: fix interface to DLPAR tools
sgiseeq: Fix return type of sgiseeq_remove
sky2 1.17
sky2: only bring up watchdog if link is active
sky2: clear PCI power control reg at startup
DM9000: fix interface hang under load
phy layer: fix genphy_setup_forced (don't reset)
Don't use GFP_DMA for zone allocation.
fix realtek phy id in forcedeth
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: work around duplicate name "VID" problem on T61
acpiphp_ibm: add missing '\n' to error message
ACPI: add dump_stack() to trace acpi_format_exception programming errors
make drivers/acpi/scan.c:create_modalias() static
ACPI: Fix a warning of discarding qualifiers from pointer target type
ACPI: "ACPI handle has no context!" should be KERN_DEBUG
ACPI video hotkey: export missing ACPI video hotkey events via input layer
ACPI: Validate XSDT, use RSDT if XSDT fails
ACPI: /proc/acpi/thermal_zone trip points are now read-only, mark them as such
ACPI: fix ia64 allnoconfig build
PNP: remove null pointer checks
PNP: remove MODULE infrastructure
ISAPNP: removed unused isapnp_detected and ISAPNP_DEBUG
PNPACPI: remove unnecessary casts of "void *"
PNPACPI: simplify irq_flags()
PNP: fix up after Lindent
ACPI: enable GPEs before calling _WAK on resume
asus-laptop: Fix rmmod of asus_laptop
sony-laptop: call sonypi_compat_init earlier
sony-laptop: enable Vaio FZ events
...
patchset against 2.6.23-rc3.
corrects missing ioremap return checks and balancing on iounmap calls, integrated changes per list
recommendations on the original set of patches..
Signed-off-by: Scott Thompson <postfail <at> hushmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This partially reverts edd0622bd2.
It turns out that the part of that commit that aimed to ensure that we
created an SLB entry for the kernel stack on secondary CPUs when
starting the CPU didn't achieve its aim, and in fact caused a
regression, because get_paca()->kstack is not initialized at the point
where slb_initialize is called.
This therefore just reverts that part of that commit, while keeping
the change to slb_flush_and_rebolt, which is correct and necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current Linus tree fails to link on pmac32:
drivers/built-in.o: In function `pmac_wakeup_devices':
via-pmu.c:(.text+0x5bab4): undefined reference to `device_power_up'
via-pmu.c:(.text+0x5bb08): undefined reference to `device_resume'
drivers/built-in.o: In function `pmac_suspend_devices':
via-pmu.c:(.text+0x5c260): undefined reference to `device_power_down'
via-pmu.c:(.text+0x5c27c): undefined reference to `device_resume'
make[1]: *** [.tmp_vmlinux1] Error 1
changing CONFIG_PM > CONFIG_PM_SLEEP leads to:
drivers/built-in.o: In function `pmu_led_set':
via-pmu-led.c:(.text+0x5cdca): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5cdce): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `pmu_req_done':
via-pmu-led.c:(.text+0x5ce3e): undefined reference to `pmu_sys_suspended'
via-pmu-led.c:(.text+0x5ce42): undefined reference to `pmu_sys_suspended'
drivers/built-in.o: In function `adb_init':
(.init.text+0x4c5c): undefined reference to `pmu_register_sleep_notifier'
make[1]: *** [.tmp_vmlinux1] Error 1
So change even more places from PM to PM_SLEEP to allow linking.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On exit do not delete gendisk's queue because this is already done by
del_gendisk(). Doing it twice may cause memory damage.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Firmware would not deliver two interrupt numbers in device-tree any more
but only one, for correctable ECC, because uncorrectable ECC from now
is handled by firmware itself.
Changes in the axonram module are necessary because in the old version, if
it is not allowed to fetch the second interrupt number from device-tree,
it interpretes this as an error case and exits.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell Broadband Engine has a method of injecting a
system-reset-exception from an external source into the
operating system, which should trigger the regular behaviour
of entering xmon or kdump.
Unfortunately, the exception handler cannot distinguish it from
other interrupt causes by the SRR1 register, which gets used
for this on Power 6 and others.
IBM Blade servers that want to support triggering the
system reset exception using a pinhole button in the front
panel therefore use an extra register to determine the
reset cause.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Legacy device tree used the reg property for the physical id of an
spe. On newer device tree layouts the reg property contains the
"correct" value in the reg attribute. So there has been intoduced the
"physical-id" on newer devicetree layouts. The id is stored by
spu_manage into the spu struct as spe_id. cbe_thermal has been
changed to use the spu->spe_id. There's no need for the thermal code
to check devicetree attributes for itself.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on a patch from Peter Oruba, convert myri10ge to use pcie_get_readrq()
and pcie_set_readrq() instead of our own PCI calls and arithmetics.
These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface. Reading and setting those values doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Includes hcp_epas_dtor in eq/cq/qp destructors to unmap
HW register.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the module parameter description of "use_mcs" to
show correct default value
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Userspace DLPAR tool expects decimal numbers to be written to
and read from sysfs entries.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver remove method needs to return an int not void. This was just
never noticed because usually this driver is not being built as a module.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.
Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As noticed by Chuck Ebbert, commit c5e3ae8823
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This can only fix the problem that more than one video bus device
have the same AML name "VID".
ie. the proc I/F for the second "VID" video bus device is located under
/proc/acpi/video/VID1/...
As this is really rare and the ACPI proc I/F is a legacy feature that
we are planning to remove.
We won't provide a generic solution for this problem.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dump the stack so we can find the secretive caller to acpi_format_exception().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes the needlessly global create_modalias() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/ec.c: In function `acpi_ec_ecdt_probe':
drivers/acpi/ec.c:873: warning: passing arg 1 of `acpi_get_devices' discards qualifiers from pointer target type
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] Make sure AH=00h when setting a video mode
[x86 setup] Volatilize asm() statements
DM_MULTIPATH_RDAC uses SCSI API(s) and is for a SCSI device,
so add SCSI to its depends on to prevent build errors.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
[ Tested and Verified by Chandra Seetharaman ]
Acked-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI 1.0 used an RSDT with 32-bit physical addresses.
ACPI 2.0 adds an XSDT with 32-bit physical addresses.
An ACPI 2.0 aware OS is supposed to use the XSDT
(when present) instead of the RSDT.
However, several systems have failed because the XSDT
contains NULL entries -- while it is missing pointers
to needed tables, such as SSDTs.
When we find an XSDT with NULL entries, discard it
and use the ACPI 1.0 RSDT instead.
http://bugzilla.kernel.org/show_bug.cgi?id=8630
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
fix task startup penalty miscalculation: sysctl_sched_granularity is
unsigned int and wait_runtime is long so we first have to convert it
to long before turning it negative ...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
current code:
delta = calc_delta_mine(delta_exec, curr->load.weight, lw);
delta = min((u64)delta, cfs_rq->sleeper_bonus);
Notice that this calc_delta_mine() line is exactly delta_mine, which
gives:
delta = min((u64)delta_mine, cfs_rq->sleeper_bonus);
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
current code:
delta = min(cfs_rq->sleeper_bonus, (u64)delta_exec);
delta = calc_delta_mine(delta, curr->load.weight, lw);
delta = min((u64)delta, cfs_rq->sleeper_bonus);
drop the first min(), because we clip against sleeper_bonus in the 3rd line
again. That gives:
delta = calc_delta_mine(delta_exec, curr->load.weight, lw);
delta = min((u64)delta, cfs_rq->sleeper_bonus);
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
make the bonus balance more consistent: do not hand out a bonus if
there's too much in flight already, and only deduct as much from a
runner as it has the capacity. This makes the bonus engine a zero-sum
game (as intended).
this also simplifies the code:
text data bss dec hex filename
34770 2998 24 37792 93a0 sched.o.before
34749 2998 24 37771 938b sched.o.after
and it also avoids overscheduling in sleep-happy workloads like
hackbench.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mitchell Erblich suggested a quality-of-implementation change to
not requeue SCHED_RR tasks if there's only a single task on the
runqueue, by checking for rq->nr_running == 1.
provide a more efficient implementation of that, to check that
particular RT priority-queue only.
[ From: mingo@elte.hu ]
Also first requeue the task then set need_resched - results in slightly
better machine-instruction ordering. Also clean up the code a bit.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove HZ dependency from the granularity default. Use 10 msec for
the base granularity, 1 msec for wakeup granularity and 25 msec for
batch wakeup granularity. (These defaults are close to the values
that the default HZ=250 setting got previously, and thus it's the
most common setting.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when I built with CONFIG_FAIR_GROUP_SCHED=y, I need the following change
to make things right.
[ From: mingo@elte.hu ]
this config option is not upstream-configurable right now but lets fix
this for completeness.
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
drivers/acpi/event.c:238: error: conflicting types for ‘acpi_bus_generate_netlink_event’
include/acpi/acpi_bus.h:324: error: previous declaration of ‘acpi_bus_generate_netlink_event’ was here
Signed-off-by: Len Brown <len.brown@intel.com>
Remove some null pointer checks. Null pointers in these areas indicate
programming errors, and I think it's better to oops immediately rather
than return an error that is easily ignored.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't support building any part of PNP as a module (*drivers* can be
modules, of course, but the PNP infrastructure itself can not). Since
MODULE will never be defined, remove the ifdefs and dead code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ISAPNP_DEBUG isn't used at all. isapnp_detected is set but never read.
So remove them both.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It seems it's required to enable GPEs before _WAK. E.g. X60 triggers a
LID related GPE instead of doing a Notify in WAK. Now the GPE reaches the
kernel and the Notify for LID status change gets thrown from there.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The asus laptop driver conditionnaly registers leds in asus_led_register()
depending on their availability, but unconditionnaly unregisters them all at
exit time or when the module fails to load. Unregistering not registered leds
result in the following Oops. So we should check before unregistering.
[<c032d2f9>] do_page_fault+0x511/0x5e9
[<c032bae2>] error_code+0x6a/0x70
[<c026abf8>] device_unregister+0x26/0x32
[<f8864218>] led_classdev_unregister+0x58/0x94 [led_class]
[<f88a90f8>] asus_led_exit+0x17/0x41 [asus_laptop]
[<f88a91c9>] asus_laptop_exit+0xd/0x3f [asus_laptop]
[<c013cee1>] sys_delete_module+0x17b/0x1a2
[<c0106eae>] sysenter_past_esp+0x6b/0xa1
EIP: [<c026a9a3>] device_del+0xb/0x23a SS:ESP 0068:f594ef0c
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: Len Brown <len.brown@intel.com>
sonypi_compat uses a kfifo that needs to be present before _SRS is
called to be able to cope with the IRQs triggered when setting
resources.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: don't check n_sectors during revalidation if zero
pata_via: Add Arima W730-K8 and other rebadgings
pata_sis: Add the FSC Amilo and friends
pata_pdc2027x: PLL detection fixes
libata: fix n_sectors failure handling during revalidation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix bad error path in conversion routines
9p: remove deprecated v9fs_fid_lookup_remove()
9p: update maintainers and documentation
9p: fix use after free
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: tell which spurious interrupt we got
sdhci: handle data interrupts during command
mmc: ignore bad max block size in sdhci
sdhci: be more cautious about block count register
drivers/mmc/core/host.c: kmalloc + memset conversion to kzalloc
drivers/mmc/core/bus.c: kmalloc + memset conversion to kzalloc
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Run k8t_sound_hostbridge quirk only when needed
PCI: disable MSI on RX790
PCI: disable MSI on RD580
PCI: disable MSI on RS690
PCI: make pcie_get_readrq visible in pci.h
PCI: lets kill the 'PCI hidden behind bridge' message
pci/hotplug/cpqphp_ctrl.c: remove stale BKL use
PCI: Document pci_iomap()
PCI: quirk_e100_interrupt() called too early
PCI: Move prototypes for pci_bus_find_capability to include/linux/pci.h
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (35 commits)
usb: add PRODUCT, TYPE to usb-interface events
USB: resubmission unusual_devs modification for Nikon D80
usb quirks: Add Canon EOS 5D (PC Connection mode) to the autosuspend blacklist
USB: make EHCI initialize properly on PPC SOCs
UEAGLE: Remove sysfs files on error case
USB: fsl_usb2_udc: fix bug in processing setup requests
USB: g_file_storage: fix bug in DMA buffer handling
USB: update last_busy field correctly
USB: fix DoS in pwc USB video driver
USB: allow retry on descriptor fetch errors
USB: unkill cxacru atm driver
USB: Adding support for HTC Smartphones to ipaq
USB: another quirky device
USB: quirky mass storage device
USB: ohci, fix oddball gcc warning
usb-storage: fix bugs in the disconnect pathway
usb: typo in usb R8A66597 HCD config
USB: accept 1-byte Device Status replies, fixing some b0rken devices
USB: blacklist Samsung ML-2010 printer
usb-serial: fix oti6858.c segfault in termios handling
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
sysfs: don't warn on removal of a nonexistent binary file
HOWTO: latest lxr url address changed
HOWTO: korean translation of Documentation/HOWTO
Fix Off-by-one in /sys/module/*/refcnt
sysfs: fix locking in sysfs_lookup() and sysfs_rename_dir()
Include asm-generic/pgtable.h to pick up the lazy_mmu_mode and
lazy_cpu_mode macros. Won't build without them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Whoever did the PCI revision patch slipped up on the it821x, and I
didn't spot this at the time either. They moved the check for the
errata from the 0x10 revision to 0x11. Put it back
This one is important for 2.6.23 final as in some cases bad things will
occur if 0x10 revision boards don't get the fixups.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both ACPI_VIDEO_NOTIFY_SWITCH and ACPI_VIDEO_NOTIFY_PROBE
are valid for video bus devices only. Actually ACPI video output
device should never be notified for a output device switch/probe.
ACPI bus devices notify handler already has the code to
handle these kinds of events.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Passing a u8 into a register doesn't mean gcc will zero-extend it.
Also, don't depend on thhe register not to change.
Per bug report from Saul Tamari.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
asm() statements need to be volatile when:
a. They have side effects (other than value returned).
b. When the value returned can vary over time.
c. When they have ordering constraints that cannot be expressed to gcc.
In particular, the keyboard and timer reads were violating constraint (b),
which resulted in the keyboard/timeout poll getting
loop-invariant-removed when compiling with gcc 4.2.0.
Thanks to an anonymous bug reporter for pointing this out.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Schedule /proc/acpi/event for removal in 6 months.
Re-name acpi_bus_generate_event() to acpi_bus_generate_proc_event()
to make sure there is no confusion that it is for /proc/acpi/event only.
Add CONFIG_ACPI_PROC_EVENT to allow removal of /proc/acpi/event.
There is no functional change if CONFIG_ACPI_PROC_EVENT=y
Signed-off-by: Len Brown <len.brown@intel.com>
The previous events patch added a netlink event for every
user of the legacy /proc/acpi/event interface.
However, some users of /proc/acpi/event are really input events,
and they already report their events via the input layer.
Introduce a new interface, acpi_bus_generate_netlink_event(),
which is explicitly called by devices that want to repoprt
events via netlink. This allows the input-like events
to opt-out of generating netlink events. In summary:
events that are sent via netlink:
ac/battery/sbs
thermal
processor
thinkpad_acpi dock/bay
events that are sent via input layer:
button
video hotkey
thinkpad_acpi hotkey
asus_acpi/asus-laptop hotkey
sonypi/sonylaptop
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
static function dvb_net_sec declares input arg "pkt" as u8. However, the
same argument at dvb_net_sec_callback is defined as "const u8". When
calling dvb_net_sec, this is casted as just "u8".
gcc 4.2.1 generates a warning about that:
CC [M] drivers/media/dvb/dvb-core/dvb_net.o
drivers/media/dvb/dvb-core/dvb_net.c: In function "dvb_net_sec_callback":
drivers/media/dvb/dvb-core/dvb_net.c:905: warning: passing argument 2 of
"dvb_net_sec" discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Git changeset 6bdcc6e6db dropped the
stand-alone lgh06xf module, whose functionality was absorbed into the
dvb-pll module. However, there was a minor difference between the code
in lgh06xf and dvb-pll, which caused a regression in b2c2-flexcop
devices using the LG-H06xF NIM.
dvb-pll will probe for the presence of an i2c pll chip by performing a
single byte read, the lgh06xf driver did not do this. Unfortunately, the
code in flexcop-i2c.c does not currently support 1 byte or 0 byte reads
as a probe. Such probes with the current code will always fail.
In order to work around this problem, and restore proper functionality
of the Airstar HD5000 device, this hack was created to make the probe
appear to succeed. The single byte read in dvb_pll_attach is the only
place where such a probe would ever occur, so this change is safe, and
will not affect any other devices.
Of course, if one knew how to actually perform the read operation, it
would be better to go that route. In the meantime, however, we must
apply this workaround, in order to prevent the regression that causes
tuning to fail on the Airstar HD5000 ATSC device.
Thanks to Jarod Wilson, who had originally reported this regression, and
to Geoffrey Hausheer, whose original workaround patch led us to find the
actual cause of the problem.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Geoffrey Hausheer <inli3epy93n@phracturedblue.com>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When buf_check_overflow() returns != 0 we will hit kfree(ERR_PTR(err))
and it will not be happy about it.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch removes the v9fs_fid_lookup_remove which is no longer used.
Based on original patch from Adrian Bunk <bunk@stusta.de> which
used #if 0 to isolate the code.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Updates to the MAINTAINERS file and documentation for 9p to point to the
swik wiki versus the outdated sf.net page. Also updated some email addresses
and added pointers to papers which better describe the implementation and
application of the Linux 9p client.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
On 7/22/07, Adrian Bunk <bunk@stusta.de> wrote:
The Coverity checker spotted the following use-after-free
in net/9p/mux.c:
<-- snip -->
...
struct p9_conn *p9_conn_create(struct p9_transport *trans, int msize,
unsigned char *extended)
{
...
if (!m->tagpool) {
kfree(m);
return ERR_PTR(PTR_ERR(m->tagpool));
}
...
<-- snip -->
Also spotted was a leak of the same structure further down in the function.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Michael Gerdau reported reniced task CPU usage weirdnesses.
Such symptoms can be caused by limit underruns so double the
sched_runtime_limit.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Was playing with sched_smt_power_savings/sched_mc_power_savings and
found out that while the scheduler domains are reconstructed when sysfs
settings change, rebalance_domains() can get triggered with null domain
on other cpus, which is setting next_balance to jiffies + 60*HZ.
Resulting in no idle/busy balancing for 60 seconds.
Fix this.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On a four package system with HT - HT load balancing optimizations were
broken. For example, if two tasks end up running on two logical threads
of one of the packages, scheduler is not able to pull one of the tasks
to a completely idle package.
In this scenario, for nice-0 tasks, imbalance calculated by scheduler
will be 512 and find_busiest_queue() will return 0 (as each cpu's load
is 1024 > imbalance and has only one task running).
Similarly MC scheduler optimizations also get fixed with this patch.
[ mingo@elte.hu: restored fair balancing by increasing the fuzz and
adding it back to the power decision, without the /2
factor. ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the accounting regression for CONFIG_VIRT_CPU_ACCOUNTING. It
reverts parts of commit b27f03d4bd by
converting fs/proc/array.c back to cputime_t. The new functions
task_utime and task_stime now return cputime_t instead of clock_t. If
CONFIG_VIRT_CPU_ACCOUTING is set, task->utime and task->stime are
returned directly instead of using sum_exec_runtime.
Patch is tested on s390x with and without VIRT_CPU_ACCOUTING as well as
on i386.
[ mingo@elte.hu: cleanups, comments. ]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are two remaining gotchas:
- The directories have impossible permissions (writeable).
- The ctl_name for the kernel directory is inconsistent with
everything else. It should be CTL_KERN.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
construct a more or less wall-clock time out of sched_clock(), by
using ACPI-idle's existing knowledge about how much time we spent
idling. This allows the rq clock to work around TSC-stops-in-C2,
TSC-gets-corrupted-in-C3 type of problems.
( Besides the scheduler's statistics this also benefits blktrace and
printk-timestamps as well. )
Furthermore, the precise before-C2/C3-sleep and after-C2/C3-wakeup
callbacks allow the scheduler to get out the most of the period where
the CPU has a reliable TSC. This results in slightly more precise
task statistics.
the ACPI bits were acked by Len.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
This patch reduces 36-bit offset to 32-bit offsets. The 36-bit
offsets makes virtual addresses wraps when added to 32-bit base.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pins for GPIO should be provided as plain number
build as (GPIO_PORTx + pin_number). But to setup
the output GPIO_GIUS and GPIO_DR have to be specified
in mode to route right value to the pin.
This is a fix, it should go to 2.6.23
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For ARM at91, the FIQ_START #define is required if you use a driver
that enables FIQ support.
Signed-off-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Andrew Victor <andrew at sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression from around 2.6.18, consistent_sync() will now BUG()
under these circumstances. The use of consistent_sync() was a hack, replacing
it's usage here with a new function, flush_ioremap_region().
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the initial configuration fails early, n_sectors is left at zero.
Checking against it during revalidation makes retried configuration
fail due to n_sectors mismatch. Ignore zero n_sectors during
revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously I reported that the pata_pdc2027x PLL detection changes
in kernel 2.6.22 broke the driver on my PowerMac:
>pata_pdc2027x: Invalid PLL input clock 1691742kHz, give up!
This is followed by a number of errors and speed reduction
steps on the affected ports.
There are two bugs in pata_pdc2027x's PLL detection code:
1. The PLL counter's start value is read before the chip is
put in "test mode". Outside of test mode the counter is
halted, and on the PowerMac the counter is zero because
the chip hasn't been initialised by its BIOS.
The fix is to move the read of the start value to after
test mode is started, but before the mdelay() in test mode.
This also improves the precision of the PLL detection.
2. The code to compute the number of PLL decrements during the
mdelay() in test mode fails to consider that the PLL counter
only is 30 bits wide. If there is a wraparound, it will compute
an incorrect and much too large value. On the PowerMac, the
start count is zero, the end count is a large 30-bit value, so
wraparound occurs and an out of bounds PLL clock is detected.
The fix is to mask the (start - end) computation to 30 bits.
While debugging this I also noticed that pdc_read_counter()
reads the two halves of the 30-bit PLL counter as 16-bit values,
and then combines them as if the halves only are 15 bits wide.
To avoid confusion, the halves should be read as 15-bit values.
This patch implements all three changes. It fixes the PLL detection
failure on my PowerMac, and doesn't cause any regressions on an x86
with an identical card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If revalidation fails because device has different n_sectors after
configuration the original n_sectors should be restored before failing
revalidation. Without this fix, n_sectors difference will incorrectly
and silently pass revalidation when revalidation is retried.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some SDHC cards report an invalid maximum block size, in these cases
assume they support block sizes up to 512 bytes instead of returning
an error.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The block count register shouldn't be trusted for single block transfers,
so avoid using it completely when calculating transferred bytes.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The NUMA layer only supports NUMA policies for the highest zone. When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE. The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.
This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE. As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.
The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64. No abnormal results were seen in
kernbench, tbench, dbench or hackbench. It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.
akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23. Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on. That solution
would only use a single zonelist per node and filter on the fly. That may
help performance and also help to make memory policies work better."
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
au1100fb_fb_blank() should come before au1100fb_setmode().
drivers/video/au1100fb.c: In function 'au1100fb_setmode':
drivers/video/au1100fb.c:211: error: implicit declaration of function 'au1100fb_fb_blank'
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/console/newport_con.c: In function `newport_console_init':
drivers/video/console/newport_con.c:743: warning: return makes integer from pointer without a cast
Although one wonders whether that should have been -ENODEV...
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In file included from drivers/video/console/newport_con.c:16:
include/linux/selection.h:16: warning: "struct tty_struct" declared inside parameter list
include/linux/selection.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen i386 xen-head.S fix sections mixup
xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.
Updates:
- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
does its own push/popsection to put things into the appropriate .note* section
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
de_thread:
if (atomic_read(&oldsighand->count) <= 1)
BUG_ON(atomic_read(&sig->count) != 1);
This is not safe without the rmb() in between. The results of two
correctly ordered __exit_signal()->atomic_dec_and_test()'s could be seen
out of order on our CPU.
The same is true for the "thread_group_empty()" case, __unhash_process()'s
changes could be seen before atomic_dec_and_test(&sig->count).
On some platforms (including i386) atomic_read() doesn't provide even the
compiler barrier, in that case these checks are simply racy.
Remove these BUG_ON()'s. Alternatively, we can do something like
BUG_ON( ({ smp_rmb(); atomic_read(&sig->count) != 1; }) );
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches. This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Print a big fat warning and do what is necessary to continue if a node is
marked as up (meaning either node is online (upstream) or node has memory
(Andrew's tree)) but allocations from the node do not succeed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This one-liner patch fixes a bug in drivers/auxdisplay/cfag12864b.c
At cfag12864b_init(), the driver tries to kalloc some memory in the
variable cfag12864b_cache.
Then, as usual, it checks if the call failed. However, it checks
cfag12864b_buffer instead.
This patch changes the "cfag12864b_buffer" to "cfag12864b_cache" so the
correct variable is checked.
Signed-off-by: Miguel Ojeda <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to inconsistent locking in the VFS between calls to lookup and
revalidate deadlock can occur in the automounter.
The inconsistency is that the directory inode mutex is held for both lookup
and revalidate calls when called via lookup_hash whereas it is held only
for lookup during a path walk. Consequently, if the mutex is held during a
call to revalidate autofs4 can't release the mutex to callback the daemon
as it can't know whether it owns the mutex.
This situation happens when a process tries to create a directory within an
automount and a second process also tries to create the same directory
between the lookup and the mkdir. Since the first process has dropped the
mutex for the daemon callback, the second process takes it during
revalidate leading to deadlock between the autofs daemon and the second
process when the daemon tries to create the mount point directory.
After spending quite a bit of time trying to resolve this on more than one
occassion, using rather complex and ulgy approaches, it turns out that just
delaying the hashing of the dentry until the create operation works fine.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a raid1 array is reshaped (number of drives changed), the list of devices
is compacted, so that slots for missing devices are filled with working
devices from later slots. This requires the "rd%d" symlinks in sysfs to be
updated.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1757128438 was slightly bad. If an array
has a write-intent bitmap, and you remove a drive, then readd it, only the
changed parts should be resynced. However after the above commit, this only
works if the array has not been shut down and restarted.
This is because it sets 'fullsync' at little more often than it should. This
patch is more careful.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems a simple mistake was made when converting follow_hugetlb_page()
over to the VM_FAULT flags bitmasks (in "mm: fault feedback #2", commit
83c54070ee).
By using the wrong bitmask, hugetlb_fault() failures are not being
recognized. This results in an infinite loop whenever follow_hugetlb_page
is involved in a failed fault.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Skip calling cache_free_alien() when the platform is not numa capable.
This will avoid cache misses that happen while accessing slabp (which is
per page memory reference) to get nodeid. Instead use a global variable to
skip the call, which is mostly likely to be present in the cache.
This gives a 0.8% performance boost with the database oltp workload on a
quad-core SMP platform and by any means the number is not small :)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch any thread can dequeue its own private signals via signalfd,
even if it was created by another sub-thread.
To do so, we pass "current" to dequeue_signal() if the caller is from the same
thread group. This also fixes the scheduling of posix timers broken by the
previous patch.
If the caller doesn't belong to this thread group, we can't handle __SI_TIMER
case properly anyway. Perhaps we should forbid the cross-process signalfd usage
and convert ctx->tsk to ctx->sighand.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dequeue_signal:
if (__SI_TIMER) {
spin_unlock(&tsk->sighand->siglock);
do_schedule_next_timer(info);
spin_lock(&tsk->sighand->siglock);
}
Unless tsk == curent, this is absolutely unsafe: nothing prevents tsk from
exiting. If signalfd was passed to another process, do_schedule_next_timer()
is just wrong.
Add yet another "tsk == current" check into dequeue_signal().
This patch fixes an oopsable bug, but breaks the scheduling of posix timers
if the shared __SI_TIMER signal was fetched via signalfd attached to another
sub-thread. Mostly fixed by the next patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_timer_create() sets ->it_process and unlocks ->siglock, then checks
tmr->it_sigev_notify to define if get_task_struct() is needed.
We already passed ->it_id to the caller, another thread can delete this timer
and free its memory in between.
As a minimal fix, move this code under ->siglock, sys_timer_delete() takes it
too before calling release_posix_timer(). A proper serialization would be to
take ->it_lock, we add a partly initialized timer on posix_timers_id, not
good.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
timer_delete does:
lock_timer();
timer->it_process = NULL;
unlock_timer();
release_posix_timer();
timer->it_process is checked in lock_timer() to prevent access to a
timer, which is on the way to be deleted, but the check happens after
idr_lock is dropped. This allows release_posix_timer() to delete the
timer before the lock code can check the timer:
CPU 0 CPU 1
lock_timer();
timer->it_process = NULL;
unlock_timer();
lock_timer()
spin_lock(idr_lock);
timer = idr_find();
spin_lock(timer->lock);
spin_unlock(idr_lock);
release_posix_timer();
spin_lock(idr_lock);
idr_remove(timer);
spin_unlock(idr_lock);
free_timer(timer);
if (timer->......)
Change the locking to prevent this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k/mac: Make mac_hid_mouse_emulate_buttons() declaration visible
drivers/char/keyboard.c: In function 'kbd_keycode':
drivers/char/keyboard.c:1142: error: implicit declaration of function 'mac_hid_mouse_emulate_buttons'
The forward declaration of mac_hid_mouse_emulate_buttons() is not visible on
m68k because it's hidden in the middle of a big #ifdef block.
Move it to <linux/kbd_kern.h>, correct the type of the second parameter, and
include <linux/kbd_kern.h> where needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e. when a symbol is equal to _etext it's not
included).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspend is ever implemented for pmu68k it really should follow the
generic pm_ops concept and not mirror the platform-specific /dev/pmu
device with ioctls on it. Hence, this patch removes the unused code there;
should the implementers need it they can look at via-pmu.c and/or the
history of the file.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new exec code inserts an accounted vma into an mm struct which is not
current->mm. The existing memory check code has a hard coded assumption
that this does not happen as does the security code.
As the correct mm is known we pass the mm to the security method and the
helper function. A new security test is added for the case where we need
to pass the mm and the existing one is modified to pass current->mm to
avoid the need to change large amounts of code.
(Thanks to Tobias for fixing rejects and testing)
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Cc: James Morris <jmorris@redhat.com>
Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new rtc-m41t80 driver name doesn't match its module name, which
prevents it from properly hotplugging. Since it's new, no platforms yet
depend on that name ... so this patch fixes the driver name to match its
module name, rather than going the other way around with a MODULE_ALIAS().
NOTE: This sort of bug is a new thing to watch out for with new-style I2C
drivers; previously I2C couldn't hotplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lumpy reclaim works by selecting a lead page from the LRU list and then
selecting pages for reclaim from the order-aligned area of pages. In the
situation were all pages in that region are inactive and not referenced by any
process over time, it works well.
In the situation where there is even light load on the system, the pages may
not free quickly. Out of a area of 1024 pages, maybe only 950 of them are
freed when the allocation attempt occurs because lumpy reclaim returned early.
This patch alters the behaviour of direct reclaim for large contiguous
blocks.
The first attempt to call shrink_page_list() is asynchronous but if it fails,
the pages are submitted a second time and the calling process waits for the IO
to complete. This may stall allocators waiting for contiguous memory but that
should be expected behaviour for high-order users. It is preferable behaviour
to potentially queueing unnecessary areas for IO. Note that kswapd will not
stall in this fashion.
[apw@shadowen.org: update to version 2]
[apw@shadowen.org: update to version 3]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Mel when reclaim is applied at higher orders a significant
amount of IO may be started. As this takes finite time to drain reclaim will
consider more areas than ultimatly needed to satisfy the request. This leads
to more reclaim than strictly required and reduced success rates.
I was able to confirm Mel's test results on systems locally. These show that
even under light load the success rates drop off far more than expected.
Testing with a modified version of his patch (which follows) I was able to
allocate almost all of ZONE_MOVABLE with a near idle system. I ran 5 test
passes sequentially following system boot (the system has 29 hugepages in
ZONE_MOVABLE):
2.6.23-rc1 11 8 6 7 7
sync_lumpy 28 28 29 29 26
These show that although hugely better than the near 0% success normally
expected we can only allocate about a 1/4 of the zone. Using synchronous
reclaim for these allocations we get close to 100% as expected.
I have also run our standard high order tests and these show no regressions in
allocation success rates at rest, and some significant improvements under
load.
This patch:
We are transitioning pages from active to inactive in clear_active_flags,
those need counting as PGDEACTIVATE vm events.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b663a79c19 ("taskstats: add
context-switch counters") incorrectly removed a comma from a printf
statement. This causes corruption in the output printing or a seg
fault.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we're going to run the handler from free_irq() then we must do it with
local irq's disabled. Otherwise lockdep complains that the handler is taking
irq-safe spinlocks in a non-irq-safe fashion.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The serial_pci driver tries to guess serial ports on unknown devices based
on the PCI class (modem or serial). On certain softmodems (AC'97 modems)
this can lead to the recognition of non-existing serial ports.
This patch adds a blacklist of PCI IDs that are to be ignored by the driver.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading the LSR clears the break, parity, frame error, and overrun bits in
the 8250 chip, but these are not being saved in all places that read the
LSR. Same goes for the MSR delta bits. Save the LSR bits off whenever the
lsr is read so they can be handled later in the receive routine. Save the
MSR bits to be handled in the modem status routine.
Also, clear the stored bits and clear the interrupt registers before
enabling interrupts, to avoid handling old values of the stored bits in the
interrupt routines.
[akpm@linux-foundation.org: clean up pre-existing code]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The uart_set_termios() function will bail out early without bothering to
touch the hardware, if it decides that nothing "relevant" has changed.
Unfortunately, its idea of "relevant" doesn't include c_[io]speed. So if
the baud rate bits are BOTHER and you just change the speed, the change
gets optimised away.
This patch makes it ignore the old Bfoo bits in c_cflag and just check
whether c_ispeed and c_ospeed have changed. Those integers are always set
appropriately for us by set_termios().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I couldn't find any memory policy documentation in the Documentation
directory, so here is my attempt to document it.
There's lots more that could be written about the internal design--including
data structures, functions, etc. However, if you agree that this is better
that the nothing that exists now, perhaps it could be merged. This will
provide a baseline for updates to document the many policy patches that are
currently being worked.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Acked-by: Rob Landley <rob@landley.net>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the maintainers info in the tpm drivers. Kylene will be out for
some time, so copying the sourceforge list is the best way to get some
attention.
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Booting SPARSEMEM on NUMA systems trips a BUG in page_alloc.c:
Initializing HighMem for node 0 (00038000:00100000)
Initializing HighMem for node 1 (00100000:001ffe00)
------------[ cut here ]------------
kernel BUG at /home/apw/git/linux-2.6/mm/page_alloc.c:456!
[...]
This occurs because the section to node id mapping is not being
setup correctly during init under SPARSEMEM_STATIC, leading to an
attempt to free pages from all nodes into the zones on node 0.
When the zone_table[] was removed in the following commit, a new
section to node mapping table was introduced:
commit 89689ae7f9
[PATCH] Get rid of zone_table[]
That conversion inadvertantly only initialised the node mapping in
SPARSEMEM_EXTREME. Ensure we initialise the node mapping in
SPARSEMEM_STATIC.
[akpm@linux-foundation.org: make the stubs static inline]
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When ecryptfs_lookup() is called against special files, eCryptfs generates
the following errors because it tries to treat them like regular eCryptfs
files.
Error opening lower file for lower_dentry [0xffff810233a6f150], lower_mnt [0xffff810235bb4c80], and flags [0x8000]
Error opening lower_file to read header region
Error attempting to read the [user.ecryptfs] xattr from the lower file; return value = [-95]
Valid metadata not found in header region or xattr region; treating file as unencrypted
For instance, the problem can be reproduced by the steps below.
# mkdir /root/crypt /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# mknod /mnt/crypt/c0 c 0 0
# umount /mnt/crypt
# mount -t ecryptfs /root/crypt /mnt/crypt
# ls -l /mnt/crypt
This patch fixes it by adding a check similar to directories and
symlinks.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] PCI: make pcie_get_readrq visible in pci.h
pcie_get_readrq() is EXPORT_SYMBOL'ed, but its prototype is not
visible in pci.h, add it there.
This is needed by some network drivers.
Signed-off-by: Brice Goglin <brice@myri.com>
Acked-by: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk wrote:
> Alois Nešpor wrote
>> PCI: Bus #0b (-#0e) is hidden behind transparent bridge #0a (-#0b) (try 'pci=assign-busses')
>> Please report the result to linux-kernel to fix this permanently"
>>
>> dmesg:
>> "Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e"
>> without pci=assign-busses and nothing with pci=assign-busses.
>
> Bernhard?
Ok, lets kill the message. As Alois Nešpor also saw, that's fixed up by Yenta,
so PCI does not have to warn about it. PCI could still warn about it if
is_cardbus is 0 in that instance of pci_scan_bridge(), but so far I have
not seen a report where this would have been the case so I think we can
spare the kernel of that check (removes ~300 lines of asm) unless debugging
is done.
History: The whole check was added in the days before we had the fixup
for this in Yenta and pci=assign-busses was the only way to get CardBus
cards detected on many (not all) of the machines which give this warning.
In theory, there could be cases when this warning would be triggered and
it's not cardbus, then the warning should still apply, but I think this
should only be the case when working on a completely broken PCI setup,
but one may have already enabled the debug code in drivers/pci and the
patched check would then trigger.
I do not sign this off yet because it's completely untested so far, but
everyone is free to test it (with the #ifdef DEBUG replaced by #if 1 and
pr_debug( changed to printk(.
We may also dump the whole check (remove everything within the #ifdef from
the source) if that's perferred.
On Alois Nešpor's machine this would then (only when debugging) this message:
"PCI: Bus #0b (-#0e) is partially hidden behind transparent bridge #0a (-#0b)"
"partially" should be in the message on his machine because #0b of #0b-#0e
is reachable behind #0a-#0b, but not #0c-#0e.
But that differentiation is now moot anyway because the fixup in Yenta takes
care of it as far as I could see so far, which means that unless somebody
is debugging a totally broken PCI setup, this message is not needed anymore,
not even for debugging PCI.
Ok, here the patch with the following changes:
* Refined to say that the bus is only partially hidden when the parent
bus numbers are not totally way off (outside of) the child bus range
* remove the reference to pci=assign-busses and the plea to report it
We could add a pure source code-only comment to keep a reference to
pci=assign-busses the in case when this is triggered by someone who
is debugging the cause of this message and looking the way to solve it.
From: Bernhard Kaindl <bk@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
remove stale BKL use from drivers/pci/hotplug/cpqphp_ctrl.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).
This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need pci_bus_find_capability() in some arch/powerpc code so move
the prototype into a header accessible to it.
Also kill the duplicate prototype for pci_bus_alloc_resource().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as960) removes the error message and stack dump logged by
sysfs_remove_bin_file() when someone tries to remove a nonexistent
file. The warning doesn't seem to be needed, since none of the other
file-, symlink-, or directory-removal routines in sysfs complain in a
comparable way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <htejun@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a Documentation/HOWTO korean version of 2.6.23-rc1
The header is refered to a japanese's one.
From: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sd children list walking in sysfs_lookup() and sd renaming in
sysfs_rename_dir() were left out during i_mutex -> sysfs_mutex
conversion. Fix them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Upgrade the unusual_devs.h file to support the new 1.01 firmware for the Nikon D80.
Signed-off-by: Mike Pagano <mpagano-kernel@mpagano.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent versions of the Linux kernel auto-suspend attached USB devices.
After this happens to the Canon EOS 5D camera, the camera's interrupt endpoints
don't seem to wake back up correctly, causing further use with libgphoto2
to fail with a -114 "OS error in camera communication" error.
A similar fix is probably necessary for this camera in PTP mode, which
identifies as USB product id 0x3102, but we haven't tested this.
As part of our testing process, we tried the USB_QUIRK_RESET_RESUME
quirk also, it's not helpful in this case.
Signed-off-by: Raj Kumar <rkumar@archive.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correctly initialize the on-chip EHCI controller on the AMCC PPC440EPx.
Fix "USB 0.0" initialization message, and properly put the controller
into a known state before starting it.
Add "FIXME" comment to the au1xxx bus glue which is doing the same wrong
thing here. (Who maintains that, now that AMD sold off Alchemy?) Remove
some false copyright attributions which were somehow placed in the au1xxx
bus glue then copied into ppc-soc.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: K.Boge <karsten.boge@amd.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kim Liu found that in the original code certain class setup requests
are wrongly recognized and processed as standard setup requests.
For that reason gadget ether can't work in RNDIS mode with Windows host.
The patch fixes the setup request processing code, and makes class
requests correctly passed to gadget layer.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Liu <KLiu@vixs.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as963) fixes a recently-introduced bug. The gadget
conversion removing DMA-mapped buffer allocation did not remove quite
enough code from the g_file_storage driver; DMA pointers were being
set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as966) fixes a bug in the autosuspend code. The last_busy
field should be updated whenever any event occurs, not just events
that cause an autosuspend or an autoresume.
This partially fixes Bugzilla #8892.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the pwc driver has a disconnect method that waits for user space to
close the device. This opens up an opportunity for a DoS attack,
blocking the USB subsystem and making khubd's task busy wait in
kernel space. This patch shifts freeing resources to close if an opened
device is disconnected.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as964) was suggested by Steffen Koepf. It makes
usb_get_descriptor() retry on all errors other than ETIMEDOUT, instead
of only on EPIPE. This helps with some devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it seems like you overdid it a bit in your quest to clean up the
use of urb->status. In this driver you read it the first thing, which
means that you are in a race against URB completion you'll
usually lose, returning -EINPROGRESS. This kills the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this device has been reported to break with autosuspend.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of GCC recently grew annoying warnings about constants.
This gets rid of that warning from the OHCI driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as961) fixes a couple of bugs in the disconnect pathway of
usb-storage.
The first problem, which apparently has been around for a while
although nobody noticed it, shows up when an aborted command is still
pending when a disconnect occurs. The SCSI error-handler will
continue to wait in command_abort() until the us->notify completion is
signalled. Thus quiesce_and_remove_host() needs to signal it.
The second problem was introduced recently along with autosuspend
support. Since usb_stor_scan_thread() now calls
usb_autopm_put_interface() before exiting, we can't simply leave the
scanning thread running after a disconnect; we must wait until the
thread exits. This is solved by adding a new struct completion to the
private data structure. Fortuitously, it allows the removal of the
rather clunky mechanism used in the past to insure that all threads
have finished before the module is unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have a bug which causes them to send a 1-byte reply to
Get-Device-Status requests instead of 2 bytes as required by the
spec. This doesn't play well with autosuspend, since we look for a
valid status reply to make sure the device is still present when it
resumes. Without both bytes, we assume the device has been
disconnected.
Lack of the second byte shouldn't matter much, since the spec requires
it always to be equal to 0. Hence this patch (as959) causes
finish_port_resume() to accept a 1-byte reply as valid.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The oti6858 usb serial driver should use kernel_termios_to_user_termios/
user_termios_to_kernel_termios to avoid segfaults because the kernel
uses a structure differing from that of user space with a different
size.
Signed-off-by: Thomas Viehmann <tv@beamnet.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as958) removes an unneeded and unwanted #define line from
dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If, in em28xx_usb_probe() the memory allocation
dev->alt_max_pkt_size = kmalloc(32*
dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.
This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
The patch adds device ID's for some robots which is trivial.
From: Søren Hauberg <hauberg@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Søren
It appears that one reason the "iConnect"-labeled multi-card reader was
on sale for only $5 is that it doesn't handle suspend/resume correctly.
Other than that, it was a good deal for a highspeed MMC/SD bridge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently when registration fails we're left with a stray reference to
release_mem_region(), this leads to the following case:
r8a66597_hcd r8a66597_hcd: irq 13, io base 0x18040000
drivers/usb/host/r8a66597-hcd.c: register access fail.
r8a66597_hcd r8a66597_hcd: startup error -6
r8a66597_hcd r8a66597_hcd: USB bus 1 deregistered
drivers/usb/host/r8a66597-hcd.c: Failed to add hcd
Trying to free nonexistent resource <0000000018040000-0000000018040000>
This fixes it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previous boards were likely seeing USB_ARCH_HAS_HCD selected by way
of PCMCIA or PCI, though none of those are required for hcd support
on SH. Enable support unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dell Wireless Broadband ExpressCards are rebrands of Novatel's cards.
Add all of their known PCI IDs to date along with their mapping to the exact
Novatel model to the Option driver which already claims to support them.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed this warning with CONFING_PM=n
...
drivers/usb/host/u132-hcd.c:1525: warning: 'port_power' defined but not used
...
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix typo in safe_serial.c to match the actual CONFIG variable.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the File Storage Gadget stall the control endpoint
when a MSC class request is made with wValue != 0. This change makes
some MSC compliance test warnings disappear.
Signed-off-by: Luis Lloret <luislloret@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains two fixes submitted by Ondrej Palkovsky:
- the 'ACK' packet is sent after the transfer of the USB packet is
completed, i.e. in the write_callback function. Because the close
function sends the 'abort' command, a parameter is added that allows
the caller of garmin_write_bulk to specify, if the 'ack' should be
propagated to the serial link or dimissed.
This fixes the problem with gpsbabel, it has sent several packets that
were acknowledged before they were sent to the GPS and GpsBabel closed
the device - thus effectively cancelled all outstanding requests in the
queue.
- removed the APP_RESP_SEEN and APP_REQ_SEEN flags and changed
them into counters. It evades USB reset of the gps on every device close.
Signed-off-by: Hermann Kneissel <hermann.kneissel@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as950) fixes a bug in the cdc-acm driver. It doesn't keep
track of which interface (control or data) the sysfs attributes get
registered for, and as a result, during disconnect it will sometimes
attempt to remove the attributes from the wrong interface. The
left-over attributes can cause a crash later on, particularly if the driver
module has been unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
git commit b2bbb20b37 added direct
support for PXA GPIO D+ pullup as alternative to the older udc_command
ops method. This was done by introduction of the pxa2xx_udc_mach_info
member "gpio_pullup" which, if initialized, is now used in (almost)
all places where udc_command used to be called.
This patch fixes two places where checks for availability of D+ pullup
control still only honor udc_command.
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add support for 1533 bridge to alim1535_wdt
[WATCHDOG] Add a 00-INDEX file to Documentation/watchdog/
[WATCHDOG] Eurotechwdt.c - clean-up comments
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Revert f642b26380.
[SPARC64]: Need to clobber global reg vars in switch_to().
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA] irda_nl_get_mode: always results in failure
[PPP]: Fix output buffer size in ppp_decompress_frame().
[IRDA]: Avoid a label defined but not used warning in irda_init()
[IPV6]: Fix kernel panic while send SCTP data with IP fragments
[SNAP]: Check packet length before reading
[DCCP]: Allocation in atomic context
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Change atomic_read/set to inline functions with barrier semantics.
[S390] kprobes: fix instruction length calculation
[S390] hypfs: inode corruption due to missing locking
[S390] disassembler: fix b2 opcodes like srst, bsg, and others
[S390] vmur: fix reference counting for vmur device structure
[S390] vmur: fix diag14 exceptions with addresses > 2GB.
[S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
[S390] qdio: fix EQBS handling on CCQ96
[S390] cio: change confusing message in cmf.
[S390] cio: dont forget to set last slot to NULL in ccw_uevent().
Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately. The fix is to
leave lazy mode when doing a vmalloc sync.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After doing some tests this seems to be the best variant for s390 and
should be correct as well. With gcc 4.2.1 we get the following kernel
image sizes using the default configuration:
atomic_t type volatile, atomic_read/set defines 5311824 bytes
atomic_t type int, atomic_read/set defines 5270864 bytes
atomic_t type int, atomic_read/set inline asm 5279056 bytes
atomic_t type int, atomic_read/set inline barrier 5270864 bytes
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Placing a kprobe on "bc" instruction (s390/s390x) can cause an oops.
The instruction length is encoded into the first two bits of the s390
instruction. Kprobe is incorrectly computing the instruction length.
The instruction length is used for determining what type of "fix-up" is
needed for conditional branch instruction. The problem can bee seen by
placing a kprobe on a "bc" instruction that will not branch. The
results is that Kprobe incorrectly computes the new instruction
pointer (psw.addr) after single stepping the instruction. The problem
is corrected with this patch.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
hypfs removes the whole hypfs directory tree and creates a new one, when a
process triggers an update by writing to the "update" attribute. When removing
and creating files, it is necessary to lock the inode of the parent directory
where the files live. Currently hypfs does not lock the parent inode, which
can lead to inode corruption. This patch:
* Introduces correct locking
* Fixes i_nlink reference counting for inodes, when creating directories
* Adds info printk, when hypfs filesystem has been mounted
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The instruction table for b2 opcodes was missing an opfrag value
for the cpya instruction. All instructions specified after cpya
were not considered by the disassembler. The fix is simple and
obvious - add the opfrag field to the cpya instruction.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When a vmur device is removed due to a detach of the device, currently the
ur device structure is freed. Unfortunately it can happen, that there is
still a user of the device structure, when the character device is open
during the detach process. To fix this, reference counting for the vmur
structure is introduced.
In addition to that, the online, offline, probe and remove functions are
serialized now using a global mutex.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Hipersocket Multicast queue works asynchronously. When sending buffers,
the buffer state change may happen delayed. The tasklet for checking
changes in the outbound queue excluded IQDIO async queues from this
process. This created either a hang situation when the queue ran full,
or presented a hang situation a interface close time.
The tasklet processing is changed to include IQDIO async queues when
requesting buffer state refresh.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
QDIO returned from EQBS instruction in any case after return code
CCQ=96 was issued regardless whether buffer states for at least one
buffer were extracted or not.
This caused FCP devices to hang when running under z/VM and having
QIOASSASIST=ON and having high I/O rates.
In order to fix this qdio return code processing of EQBS instruction
after CCQ=96 is changed that buffers are returned and if no buffers
where extracted the instruction is repeated at once.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
cmf currently prints a message that more than 4096 channels are not
allowed in basic mode - however, this can only be enforced if cmf was
a module (which is no longer possible). It makes much more sense to
not check the specified number of channels and just print a message if
the block for basic mode could not be allocated (which may happen for
any number of specified channels).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bugfixes for the OSK led support:
- Fix Kconfig merge glitches: Mistral handles idle and timer leds just fine
- Fix pm_suspend() runtime botch: can't sleep, so can't touch tps65010 leds
Improvements:
- Switch sense of Mistral idle led, so idle == off
Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a plat_irq_setup() symbol for sh4-202. Without
this fix it is impossible to build a working kernel using the
microdev_defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It seems an extraneous trailing ';' has slipped in to the error handling for a
name registration failure causing the error path to trigger unconditionally.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the issue with "osize too small" errors in mppe
encryption. The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.
--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Easily avoidable compiler warnings bug me.
Building irmod without CONFIG_SYSCTL currently results in :
net/irda/irmod.c:132: warning: label 'out_err_2' defined but not used
But that can easily be avoided by simply moving the label inside
the existing "#ifdef CONFIG_SYSCTL" one line above it.
This patch moves the label and buys us one less warning with no
ill effects.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snap_rcv code reads 5 bytes so we should make sure that
we have 5 bytes in the head before proceeding.
Based on diagnosis and fix by Evgeniy Polyakov, reported by
Alan J. Wylie.
Patch also kills the skb->sk assignment before kfree_skb
since it's redundant.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerd Hoffmann pointed out that my patch from yesterday can lead
to a null pointer dereference if the kernel is booted with no
console, and no earlyprintk defined. This fixes that issue.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The initial user manuals for MPC8544/8533 had some issues with properly
documenting the device IDs for MPC8544/8533. These processors are almost
identical and both show up on the reference boards.
Fix up the quirks for PCIe support to handle MPC8533/E.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes handling of USB ISO completion error -EXDEV and includes
several other changes to current CVS version at isdn4linux.de (changes
in debug flags, style of code remarks, etc)
Signed-off-by: Martin Bachem <info@colognechip.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I did some testing and found quite a lot of problems (doesn't
boot at all on non NUMA and misassigns cores on Opteron systems).
Mark it as experimental and warn against its use for now.
It's still default y for SUMMIT/NUMAQ because it'll presumably
work on these systems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older versions of binutils do not support -Wa,-isa= tuning, which is
something we rely on for enabling DSP opcode support on the newer
parts. SH3-DSP parts can still be handled with -Wa,-dsp even if the
newer parts require the newer versions of binutils for supporting the
new opcodes.
This was broken in -rc1 when the SH4AL-DSP support was being reworked,
and is needed to get SH3-DSP working with older toolchains again.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This causes boot failures for some people.
It looks like in fact that some SILO provided
ramdisk images should not be KERNBASE normalized.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 196705c9bb. It was
reported to cause a regression by Daniel Exner, and Arjan van de Ven
points out that we actually already have infrastructure in place for
setting limits on acceptable DMA latency that would be the much more
correct fix for the problem with some Broadcom EHCI controllers.
Fixed up trivial conflicts due to the changes to support big-endian host
controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses kzalloc to zero all of struct dio rather than manually
trying to track which fields we rely on being zero. It passed aio+dio
stress testing and some bug regression testing on ext3.
This patch was introduced by Linus in the conversation that lead up to
Badari's minimal fix to manually zero .map_bh.b_state in commit:
6a648fa721
It makes the code a bit smaller. Maybe a couple fewer cachelines to
load, if we're lucky:
text data bss dec hex filename
3285925 568506 1304616 5159047 4eb887 vmlinux
3285797 568506 1304616 5158919 4eb807 vmlinux.patched
I was unable to measure a stable difference in the number of cpu cycles
spent in blockdev_direct_IO() when pushing aio+dio 256K reads at
~340MB/s.
So the resulting intent of the patch isn't a performance gain but to
avoid exposing ourselves to the risk of finding another field like
.map_bh.b_state where we rely on zeroing but don't enforce it in the
code.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (6028): Turn an unnecessary mdelay() into msleep().
V4L/DVB (6027): Get rid of an ill-behaved msleep in i2c write
V4L/DVB (6026): Avoid powering up the camera on resume
V4L/DVB (6016): get_dvb_firmware: update script for new location of tda10046 firmware
V4L/DVB (5991): dvb-pll: Set minimum and maximum frequency properly
V4L/DVB (5969): ivtv: report ivtv version in status log
V4L/DVB (5967): ivtv: fix VIDIOC_S_FBUF:new OSD values where never set
V4L/DVB (5968): videodev2.h: remove superfluous FBUF GLOBAL_INV_ALPHA support
Commit a491486a20 introduced a locking
problem in JFFS2 -- we up() the alloc_sem when we weren't previously
holding it. This leads to all kinds of fun behaviour later.
There was a _reason_ for the
if (1 /* alternative path needs testing */ ||
which the above-mentioned commit removed :)
Discovered and debugged by Giulio Fedel <giulio.fedel@andorsystems.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In MPS mode, "nosmp" and "maxcpus=0" boot a UP kernel with IOAPIC disabled.
However, in ACPI mode, these parameters didn't completely disable
the IO APIC initialization code and boot failed.
init/main.c:
Disable the IO_APIC if "nosmp" or "maxcpus=0"
undefine disable_ioapic_setup() when it doesn't apply.
i386:
delete ioapic_setup(), it was a duplicate of parse_noapic()
delete undefinition of disable_ioapic_setup()
x86_64:
rename disable_ioapic_setup() to parse_noapic() to match i386
define disable_ioapic_setup() in header to match i386
http://bugzilla.kernel.org/show_bug.cgi?id=1641
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value. This results in +1 sector
capacity being used and errors on attempts to use the last sector.
...
hdd: Host Protected Area detected.
    current capacity is 78165360 sectors (40020 MB)
    native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...
Add hpa_list[] table and workaround the issue in idedisk_check_hpa().
v2:
* Add missing export and improve patch description a bit.
v3:
* Add list termination. (From Mikko)
Fixes kernel bugzilla bug #8816.
Thanks to Mikko for investigating the issue and helping with this patch.
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Programming DMA mode may destroy current PIO mode setting so if
CONFIG_HPT34X_AUTODMA=n (the default case) make ide_tune_dma() fail
early by disabling all host DMA masks and re-tune PIO mode.
This fix doesn't help with the driver being broken but is needed
for some other changes.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->OUTBSYNC instead of ->OUTB when writing command register
(needed for scc_pata and pmac host drivers).
* Don't check DRDY bit of the status register on ATAPI devices
(ATAPI devices are free to ignore DRDY bit).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_tune_chipset() don't set drive->init_speed.
Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC. In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These days, CONFIG_IDE_GENERIC causes more confusion and
misconfiguration than it helps. Especially so because libata is
linked after the generic driver. Default to N.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: "P.C.Chan" <pc.chan@alcatel-lucent.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Configuring the OLPC camera requires something over 150 register
writes. Unfortunately, querying the CAFE i2c controller too
soon after a write causes the hardware to flake. The problem had
been "solved" with an msleep() call, but, between the number of
registers and how msleep() behaves, that resulted in a 3-second
delay on camera initialization. Instead, we hand-code a wait for
the completion interrupt which avoids reading the status registers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update get_dvb_firmware script for the new location of the
tda10046 firmware.
The old location doesn't work anymore.
Signed-off-by: Andreas Arens <ari@goron.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner maximum frequency wasn't being set, while the minimum
frequency was set to what the maximum should have been.
If a future patch were to enforce these limits, dvb-pll would be
effectively broken.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv: fix VIDIOC_S_FBUF support: new OSD values where never actually set.
The values set with VIDIOC_S_FBUF were not actually used until the next
VIDIOC_S_FMT. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no need for a global inverted alpha capability since all the
application has to do is to pass '255-alpha' as the global alpha value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When taking a cpu down, we need to hardware_disable() it.
Unfortunately, the CPU_DYING notifier is called with interrupts
disabled, which means we can't use smp_call_function_single().
Fortunately, the CPU_DYING notifier is always called on the dying cpu,
so we don't need to use the function at all and can simply call
hardware_disable() directly.
Tested-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the second inclusion of linux/capability.h, which has been
introduced with "[PATCH] move capable() to capability.h" (commit
c59ede7b78)
Signed-off-by: Christian Heim <phreak@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With commit ab144f5ec6 the patching code
now collects the complete new instruction stream into a temp buffer
before finally patching in the new insns. In some cases the paravirt
patchers will choose to leave the patch site unpatched (length mismatch,
clobbers mismatch, etc).
This causes the new patching code to copy an uninitialized temp buffer,
i.e. garbage, to the callsite. Simply make sure to always initialize
the buffer with the original instruction stream. A better fix is to
audit all the patchers and return proper length so that apply_paravirt()
can skip copies when we leave the patch site untouched.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Very old binutils (2.12.90...) seem to have trouble with newlines
in assembler macro invocation. They put them into the resulting
argument expansion. In this case this lead to a parse error because
a .rept expression ended up spread over multiple lines. Change the PMDS()
invocation to a single line.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should fix an oops with PCMCIA PATA devices
http://bugzilla.kernel.org/show_bug.cgi?id=8424
This is not a full fix for the problem, but probably
still the right thing to do.
[ I'm almost certain it's *not* the right thing to do, but it avoids an
oops, and I want comments from others on what the right thing would
actually be.. I suspect we should just remove the use of dma_mask
entirely in this function, and just use coherent_dma_mask. - Linus ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ. It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.
This patch moves the printk's out of the spinlock protected area.
Without this patch the machine hangs hard. With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: Timo Jantunen <jeti@iki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use cpu_relax() in the busy loops, as atomic_read() doesn't automatically
imply volatility for i386 and x86_64. x86_64 doesn't have this issue because
it open-codes the while loop in smpboot.c:smp_callin() itself that already
uses cpu_relax().
For i386, however, smpboot.c:smp_callin() calls wait_for_init_deassert()
which is buggy for mach-default and mach-es7000 cases.
[ I test-built a kernel -- smp_callin() itself got inlined in its only
callsite, smpboot.c:start_secondary() -- and the relevant piece of
code disassembles to the following:
0xc1019704 <start_secondary+12>: mov 0xc144c4c8,%eax
0xc1019709 <start_secondary+17>: test %eax,%eax
0xc101970b <start_secondary+19>: je 0xc1019709 <start_secondary+17>
init_deasserted (at 0xc144c4c8) gets fetched into %eax only once and
then we loop over the test of the stale value in the register only,
so these look like real bugs to me. With the fix below, this becomes:
0xc1019706 <start_secondary+14>: pause
0xc1019708 <start_secondary+16>: cmpl $0x0,0xc144c4c8
0xc101970f <start_secondary+23>: je 0xc1019706 <start_secondary+14>
which looks nice and healthy. ]
Thanks to Heiko Carstens for noticing this.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lguest block device only requests one minor, which means
partitions don't work (eg "root=/dev/lgba1").
Let's follow the crowd and ask for 16.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Cross-compilation between e.g. i386 -> 64bit could break -> work around it
[IA64] Enable early console for Ski simulator
[IA64] forbid ptrace changes psr.ri to 3
[IA64] Failure to grow RBS
[IA64] Fix processor_get_freq
[IA64] SGI Altix : fix a force_interrupt bug on altix
[IA64] Update arch/ia64/configs/* s/SLAB/SLUB/
[IA64] get back PT_IA_64_UNWIND program header
[IA64] need NOTES in vmlinux.lds.S
[IA64] make unwinder stop at last frame of the bootloader
[IA64] Clean up CPE handler registration
[IA64] Include Kconfig.preempt
[IA64] SN2 needs platform specific irq_to_vector() function.
[IA64] Use atomic64_read to read an atomic64_t.
[IA64] disable irq's and check need_resched before safe_halt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Incorrect semicolon after if statement
mlx4_core: Wait 1 second after reset before accessing device
IPoIB: Fix leak in ipoib_transport_dev_init() error path
IB/mlx4: Fix opcode returned in RDMA read completion
IB/srp: Add OUI for new Cisco targets
IB/srp: Wrap OUI checking for workarounds in helper functions
RDMA/cxgb3: Always call low level send function via cxgb3_ofld_send()
IB: Move the macro IB_UMEM_MAX_PAGE_CHUNK() to umem.c
IB: Include <linux/list.h> and <linux/rwsem.h> from <rdma/ib_verbs.h>
IB: Include <linux/list.h> from <rdma/ib_mad.h>
IB/mad: Fix address handle leak in mad_rmpp
IB/mad: agent_send_response() should be void
IB/mad: Fix memory leak in switch handling in ib_mad_recv_done_handler()
IB/mad: Fix error path if response alloc fails in ib_mad_recv_done_handler()
IB/sa: Don't need to check for default P_Key twice
IB/core: Ignore membership bit in ib_find_pkey()
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[MATH-EMU]: Fix underflow exception reporting.
[SPARC64]: Create a HWCAP_SPARC_N2 and report it to userspace on Niagara-2.
[SPARC64]: SMP trampoline needs to avoid %tick_cmpr on sun4v too.
[SPARC64]: Do not touch %tick_cmpr on sun4v cpus.
[SPARC64]: Niagara-2 optimized copies.
[SPARC64]: Allow userspace to get at the machine description.
[SPARC32]: Remove superfluous 'kernel_end' alignment on sun4c.
[SPARC32]: Fix bogus ramdisk image location check.
[SPARC32]: Remove iommu from struct sbus_bus and use archdata like sparc64.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix invalid semicolon after if statement
[POWERPC] ps3: Fix no storage devices found
[POWERPC] Fix for assembler -g
[POWERPC] Fix small race in 44x tlbie function
[POWERPC] Remove unused code causing a compile warning
[POWERPC] cell: Fix errno for modular spufs_create with invalid neighbour
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] edd.c: make sure MBR signatures actually get reported
[x86 setup] Don't use EDD to get the MBR signature
[x86 setup] The current display page is returned in %bh, not %bl
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Check return code on failed alloc
[CIFS] Update CIFS project web site
[CIFS] Fix hang in find_writable_file
Adrian Bunk: scripts/mod/file2alias.c is compiled with HOSTCC and ensures that
kernel_ulong_t is correct, but it can't cope with different padding on
different architectures.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When using Ski to debug early startup, it's a bit of a pain not to
have printk.
This patch enables the simulated console very early.
It may be worth conditionalising on the command line... but this is
enough for now.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The "ri" field in the processor status register only has defined
values of 0, 1, 2. Do not let ptrace set this to 3. As with
other reserved fields in registers we silently discard the value.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CC arch/powerpc/sysdev/commproc.o
arch/powerpc/sysdev/fsl_soc.c: In function fsl_pcmcia_of_init:
arch/powerpc/sysdev/fsl_soc.c:1109: error: implicit declaration of function of_platform_device_create
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reserved MCSR bits on FSL BookE parts may have spurious values
when mcheck occurs. Mask these off when printing the MCSR to
avoid confusion. Also, get rid of the MCSR_GL_CI bit defined
for e500 - this bit doesn't actually have any meaning.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC CMOS driver expects the interrupt to be a resource of the platform
device. Use a fixed interrupt value of 8 since on PPC if we are using this
its off an i8259 which we ensure has interrupt numbers 0..15.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The underflow exception cases were wrong.
This is one weird area of ieee1754 handling in that the underflow
behavior changes based upon whether underflow is enabled in the trap
enable mask of the FPU control register. As a specific case the Sparc
V9 manual gives us the following description:
--------------------
If UFM = 0: Underflow occurs if a nonzero result is tiny and a
loss of accuracy occurs. Tininess may be detected
before or after rounding. Loss of accuracy may be
either a denormalization loss or an inexact result.
If UFM = 1: Underflow occurs if a nonzero result is tiny.
Tininess may be detected before or after rounding.
--------------------
What this amounts to in the packing case is if we go subnormal,
we set underflow if any of the following are true:
1) rounding sets inexact
2) we ended up rounding back up to normal (this is the case where
we set the exponent to 1 and set the fraction to zero), this
should set inexact too
3) underflow is set in FPU control register trap-enable mask
The initially discovered example was "DBL_MIN / 16.0" which
incorrectly generated an underflow. It should not, unless underflow
is set in the trap-enable mask of the FPU csr.
Another example, "0x0.0000000000001p-1022 / 16.0", should signal both
inexact and underflow. The cpu implementations and ieee1754
literature is very clear about this. This is case #2 above.
However, if underflow is set in the trap enable mask, only underflow
should be set and reported as a trap. That is handled properly by the
prioritization logic in
arch/sparc{,64}/math-emu/math.c:record_exception().
Based upon a report and test case from Jakub Jelinek.
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
From: Andrey Borzenkov <arvidjaar@mail.ru>
They are apparently pretty close (even lspci combines them). The patch
adds support for 0x1533 bridge in addition to 0x1535.
Tested on Toshiba Portege 4000 with
00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA Bridge
[Aladdin IV/V/V+] [10b9:1533]
00:08.0 Bridge [0680]: ALi Corporation M7101 Power Management Controller
[PMU] [10b9:7101]
with result
[ 2090.906736] PCI: Enabling device 0000:00:08.0 (0000 -> 0001)
[ 2090.914034] ALi_M1535: initialized. timeout=3D60 sec (nowayout=3D0)
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Clean-up history and add a comment about the fact that
the watchdog is actually part of the SMSC FDC 37B782
super I/O chipset.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is a bug in the ia64_do_page_fault code that can cause a failure
to grow the register backing store, or any mapping that is marked as
VM_GROWSUP if the mapping is the highest mapped area of memory.
When the address accessed is below the first mapping the previous mapping
is returned as NULL, and this case is handled. However, when the address
accessed is above the highest mapping the vma returned is NULL, this
case is not handled correctly, and it fails to spot that this access
might require an existing mapping to grow upwards.
Signed-off-by: Andrew Burgess <andrew@transitive.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It seems we have gained an extraneous trailing ';' on one of the
wait loops in scif_sercon_putc(). Although this is completely
benign as the apparent payload is also the empty statement, it
invites error in the future. Clean it up now.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Corrects an error code so that it is valid to pass to userspace.
Signed-off-by: Steve Grubb <linux_4ever@yahoo.com>
Signed-off-by: James Morris <jmorris@halo.namei>
This register is not a part of the sun4v architecture.
Niagara 1 and 2 happened to leave it around.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the OF device tree, it's useful to let userland get
at the machine description so it can pretty print the
graph etc.
The implementation is a simple MISC device with a read method.
Signed-off-by: David S. Miller <davem@davemloft.net>
A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A similar fix to netfilter from Eric Dumazet inspired me to
look around a bit by using some grep/sed stuff as looking for
this kind of bugs seemed easy to automate. This is one of them
I found where it looks like this semicolon is not valid.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent RCU work created an unbalanced rcu_read_unlock
in __sock_create. This patch fixes that. Reported by
oleg 123.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core cpufreq code doesn't appear to understand returning -EAGAIN
for the get() function of the cpufreq_driver. If PAL_GET_PSTATE returns
-1, such as when running on Xen, scaling_cur_freq is happy to return
4294967285 kHz (ie. (unsigned)-11). The other drivers appear to return
0 for a failure, and doing so gives me the max frequency from
scaling_cur_frequency and "<unknown>" from cpuinfo_cur_frequency. I
believe that's the desired behavior.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add empty definition of mmiowb() since some drivers need it. Uncached
writes are strongly ordered on AVR32. They may be delayed if the
dcache is busy doing a writeback, but AFAICT that's not what this
macro is supposed to deal with, at least on UP systems.
We might have to revisit this definition when a SMP-capable AVR32 CPU
comes along, depending on how the busses and cache coherency stuff
end up being implemented.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current definition of pte_page() masks out valid bits from the
physical address, causing vmalloc_to_page() to misbehave. This may
lead to everything from mmap() silently accessing the wrong data to
"invalid pte" errors dumped by the kernel.
Also remove the now-unused definition of PTE_PHYS_MASK.
Thanks to Matteo Vit for discovering this bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There's really no need to retry an allocation with __GFP_REPEAT set.
Also, use get_zeroed_page() and __GFP_ZERO to eliminate the extra call
to clear_page() afterwards.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add TECRA M7 to broken suspend list. Reported by Marie Koreen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix several inconsistencies in these drivers WRT reporting the clocks:
- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
PCI clock -- make it properly report both clocks and add the same ability to
the 'pata_hpt3x2n' driver;
- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
messages -- make them use only the former one;
- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):
* Fix the problem by adding missing struct ata_port_info to artop_init_one().
* Use the right naming (s/626/628/).
* Bump driver version.
Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix probing of PS3 storage devices: in the success case, we should set
`error' to zero, not `result'.
Without this patch no storage devices are found.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc64 does the unusual thing of using #include on a compiler-generated
assembly file (lparmap.s) from an assembly source file (head_64.S).
This runs afoul of my recent patch to pass -gdwarf2 to the assembler
under CONFIG_DEBUG_INFO. This patch avoids the problem by disabling
DWARF generation (-g0) when producing lparmap.s.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 440 family of processors don't have a tlbie instruction. So, we
implement TLB invalidates by explicitly searching the TLB with tlbsx.,
then clobbering the relevant entry, if any. Unfortunately the PID for
the search needs to be stored in the MMUCR register, which is also
used by the TLB miss handler. Interrupts were enabled in _tlbie(), so
an interrupt between loading the MMUCR and the tlbsx could cause
incorrect search results, and thus a failure to invalide TLB entries
which needed to be invalidated.
This fixes the problem in both arch/ppc and arch/powerpc by inhibiting
interrupts (even critical and debug interrupts) across the relevant
instructions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, spu_create with an invalid neighbo(u)r will return -ENOSYS,
not -EBADF, but only when spufs.o is built as a module.
This change adds the appropriate errno, making the behaviour the same
as the built-in case.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In sun4c_init_clean_mmu(), aligning 'kernel_end' using
SUN4C_REAL_PGDIR_ALIGN() is unnecessary since the caller
does this already.
In sun4c_paging_init(), 4 page sizes of "fluff" were added
to the address of &end. This was necessary a long time ago
when sparc32 would allocate some early data structures
by carving out memory chunks after &end but that no longer
occurs.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mirrors sparc64 commit 715a0ecc29
sparc_ramdisk_image should always be decremented by KERNBASE.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling in the MBR signature array, the setup code failed to advance
boot_params.edd_mbr_sig_buf_entries, which resulted in the valid data
being ignored.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
At least one machine has been identified in the field which advertises
EDD for all drives but locks up if one attempts an extended read from
a non-primary drive.
The MBR is always at CHS 0-0-1, so there is no reason to use an
extended read, other than the possibility that the BIOS cannot handle
it.
Although this might break as many machines as it fixes (a small number
either way), the current state is a regression but the reverse is not.
Therefore revert to the previous state of not using extended read.
Quite probably the Right Thing to do is to read using plain (CHS) read
and extended read on failure, but that change would definitely have to
go through -mm first.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Coverity checker spotted that we'd have already oops'ed if
"vlandev" was NULL.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the no longer used EXPORT_SYMBOL(dev_ethtool).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current display page is an 8-bit number, even though struct
screen_info gives it a 16-bit number. The number is returned in %bh,
so it needs to be >> 8 before storing.
Special thanks to Jeff Chua for detailed bug reporting.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Probe for hidden SSIDs if initiating pre-authentication scan and SSID
is set for STA interface.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added the monitor for outgoing frames somehow a break
statement slipped in. Remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stp change code generates "sleeping function called from invalid
context" because rtnl_lock() called with BH disabled. This fixes it by
not acquiring then dropping the bridge lock.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop packets shorter than "SIP/2.0", just ignore them. Keep-alives
can validly be shorter for example.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The userinfo component of a SIP-URI is optional, continue parsing at the
beginning of the SIP-URI in case its not found.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check got lost during the conversion to nf_conntrack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware will malfunction at a temperature below
the BIOS provided critical shutdown threshold.
This hook allows moving the critical trip points down
to a temperature which provokes a graceful shutdown
before the hardware malfunction.
http://bugzilla.kernel.org/show_bug.cgi?id=8884
WARNING: A trip-point override will not get noticed
until the system delivers a temperature change event,
or unless thermal zone polling is enabled.
eg. "thermal.tzp=10"
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[GFS2] Revert remounting w/o acl option leaves acls enabled
[GFS2] Fix setting of inherit jdata attr
[GFS2] Fix incorrect error path in prepare_write()
[GFS2] Fix incorrect return code in rgrp.c
[GFS2] soft lockup in rgblk_search
[GFS2] soft lockup detected in databuf_lo_before_commit
[DLM] fix basts for granted PR waiting CW
[DLM] More othercon fixes
[DLM] Fix memory leak in dlm_add_member() when dlm_node_weight() returns less than zero
[DLM] zero unused parts of sockaddr_storage
[DLM] fix NULL ls usage
[DLM] Clear othercon pointers when a connection is closed
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Build fix
i2c/menelaus: Build fix
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
i2c-mpc: Don't disable I2C module on stop condition
i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class
i2c/isp1301_omap: Build fixes, whitespace
i2c-mpc: Pass correct dev_id to free_irq on error path
i2c-i801: Typo: erroneous
Fixup the include files after the arch moves that
where included in 2.6.23.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Under certain conditions, the mv64xxx I2C bus can hang preventing
further operation. To make the driver more robust, we now reset
the I2C hardware and the driver state machine when such hangs are
detected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Disabling module on stop doesn't work on some CPUs (ie. mpc8241,
as reported by Guennadi Liakhovetski), so remove that.
Disable I2C module on errors/interrupts to prevent it from
locking up on mpc5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In order to be able to use sensors on the IOP3xx SoCs, one needs to set
the adapter class to I2C_CLASS_HWMON.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Build fixes for isp1301_omap driver. I think an earlier version
of this must have gotten lost somewhere, or maybe it only went
into the Linux-OMAP tree.
Also, some whitespace fixes to bring this more into sync with the
version of this found in the Linux-OMAP tree. (That version has
updates for the OTG controller on the OMAP 1710 which break that
functionality on OMAP 161x boards like the H2, so merging all of
it is not currently an option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: Use IP_VS_WAIT_WHILE when encessary.
[NET]: Share correct feature code between bridging and bonding
[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc
[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc
[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc
[DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm()
[DCCP]: fix theoretical ccids_{read,write}_lock() race
[XFRM]: Clean up duplicate includes in net/xfrm/
[TIPC]: Clean up duplicate includes in net/tipc/
[SUNRPC]: Clean up duplicate includes in net/sunrpc/
[PKT_SCHED]: Clean up duplicate includes in net/sched/
[IPV6]: Clean up duplicate includes in net/ipv6/
[IPV4]: Clean up duplicate includes in net/ipv4/
[ATM]: Clean up duplicate includes in net/atm/
[ATM]: Clean up duplicate includes in drivers/atm/
[IPCONFIG]: ip_auto_config fix
[ATM]: fore200e_param_bs_queue() must be __devinit
The PCI driver has not been merged yet, so comment out call to
ks8695_init_pci() for now.
Also fix some incorrectly marked __init and __initdata sections.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 569a7b6c2e. The
code was correct originally. The default setting for ACLs after a
remount should be to be the same as before the remount.
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Due to a mix up between the jdata attribute and inherit jdata attribute
it has not been possible to set the inherit jdata attribute on
directories. This is now fixed and the ioctl will report the inherit
jdata attribute for directories rather than the jdata attribute as it
did previously. This stems from our need to have the one bit in the
ioctl attr flags mean two different things according to whether the
underlying inode is a directory or not.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The error path in prepare_write() was incorrect in the (very rare) event
that the transaction fails to start. The following prevents a NULL
pointer dereference,
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The following patch fixes a bug where 0 was being used as a return code
to indicate "nothing to do" when in fact 0 was a valid block location
which might be returned by the function.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch seems to fix the problem described in bugzilla bug 246114.
It was written by Steve Whitehouse with some tweaking by me.
The code was looping in the relatively new section of code designed to
search for and reuse unlinked inodes. In cases where it was finding an
appropriate inode to reuse, it was looping around and finding the same
block over and over because a "<=" check should have been a "<" when
comparing the goal block to the last unlinked block found.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This is part 2 of the patch for bug #245832, part 1 of which is already
in the git tree.
The problem was that sdp->sd_log_num_databuf was not always being
protected by the gfs2_log_lock spinlock, but the sd_log_le_databuf
(which it is supposed to reflect) was protected. That meant there
was a timing window during which gfs2_log_flush called
databuf_lo_before_commit and the count didn't match what was
really on the linked list in that window. So when it ran out of
items on the linked list, it decremented total_dbuf from 0 to -1 and
thus never left the "while(total_dbuf)" loop.
The solution is to protect the variable sdp->sd_log_num_databuf so
that the value will always match the contents of the linked list,
and therefore the number will never go negative, and therefore, the
loop will be exited properly.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Fix a long standing bug where a blocking callback would be missed
when there's a granted lock in PR mode and waiting locks in both
PR and CW modes (and the PR lock was added to the waiting queue
before the CW lock). The logic simply compared the numerical values
of the modes to determine if a blocking callback was required, but in
the one case of PR and CW, the lower valued CW mode blocks the higher
valued PR mode. We just need to add a special check for this PR/CW
case in the tests that decide when a blocking callback is needed.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The last patch to clean out 'othercon' structures only fixed half the problem.
The attached addresses the other situations too, and fixes bz#238490
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
There's a memory leak in fs/dlm/member.c::dlm_add_member().
If "dlm_node_weight(ls->ls_name, nodeid)" returns < 0, then
we'll return without freeing the memory allocated to the (at
that point yet unused) 'memb'.
This patch frees the allocated memory in that case and thus
avoids the leak.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
When we build a sockaddr_storage for an IP address, clear the unused parts as
they could be used for node comparisons.
I have seen this occasionally make sctp connections fail.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Fix regression in recent patch "[DLM] variable allocation" which
attempts to dereference an "ls" struct when it's NULL.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch clears the othercon pointer and frees the memory when a connnection
is closed. This could cause a small memory leak when nodes leave the cluster.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For architectures that don't have a volatile atomic_ts constructs like
while (atomic_read(&something)); might result in endless loops since a
barrier() is missing which forces the compiler to generate code that
actually reads memory contents.
Fix this in ipvs by using the IP_VS_WAIT_WHILE macro which resolves to
while (expr) { cpu_relax(); }
(why isn't this open coded btw?)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a memory leak in net/dccp/feat.c::dccp_feat_empty_confirm(). If we
hit the 'default:' case of the 'switch' statement, then we return without
freeing 'opt', thus leaking 'struct dccp_opt_pend' bytes.
The leak is fixed easily enough by adding a kfree(opt); before the return
statement.
The patch also changes the layout of the 'switch' to be more in line with
CodingStyle.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that spin_unlock_wait() is properly ordered wrt atomic_inc().
(akpm: can't we convert this code to use rwlocks?)
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commandline:
root=/dev/mtdblock6 rw rootfstype=jffs2 ip=192.168.1.10:::255.255.255.0:localhost.localdomain:eth1:off console=ttyS0,115200
makes ip_auto_config fall back to DHCP and complain "IP-Config: Incomplete
network configuration information." depending on if CONFIG_IP_PNP_DHCP is
set or not.
The only way I can make ip_auto_config accept my IP config is to add an
entry for the server IP:
ip=192.168.1.10:192.168.1.15::255.255.255.0:localhost.localdomain:eth1:off
I think this is a bug since I am not using a NFS root FS.
The following patch fixes the above problem.
From: Andrew Morton <akpm@linux-foundation.org>
Davem said (in February!):
Well, first of all the change in question is not in 2.4.x either. I just
checked the current 2.4.x GIT tree and the test is exactly:
if (ic_myaddr == INADDR_NONE ||
#ifdef CONFIG_ROOT_NFS
(MAJOR(ROOT_DEV) == UNNAMED_MAJOR
&& root_server_addr == INADDR_NONE
&& ic_servaddr == INADDR_NONE) ||
#endif
ic_first_dev->next) {
which matches 2.6.x
I even checked 2.4.x when it was branched for 2.5.x and the test was the
same at the point in time too.
Looking at the proposed change a bit it appears that it is probably
correct, as it's trying to check that ROOT_DEV is nfs root. But if it is
correct then the UNNAMED_MAJOR comparison in the same code block should be
removed as it becomes superfluous.
I'm happy to apply this patch with that modification made.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/built-in.o(.text+0x6203bb): Section mismatch: reference to .init.text:fore200e_param_bs_queue (between 'fore200e_initialize' and 'fore200e_monitor_putc')
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ax88796.c: In function `ax_probe':
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4)
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5)
resource_size_t isn't size_t.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the pause counter to avoid a needless device reset, and
print a message telling the admin that our link partner is
flow controlling us down to 0 pkts/sec.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the interrupt has been disabled, don't call the force_interrupt provider.
Doing so can result in an infinite runaway interrupt loop.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The slab allocator was changed in 2.6.23 to default to SLUB. However,
the config files in arch/ia64/configs still use SLAB. Switch them to SLUB.
Added same change to arch/ia64/defconfig ... Tony
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Explicitly put the unwind section into its own program-header. This
used to be unnecessary (probably because binutils did it for us), but
with current binutils (e.g., v2.17.50.20070804) we won't get
the PT_IA_64_UNWIND header without this patch which will break
unwinding in a debugger and simulators such as Ski.
Signed-off-by: David Mosberger-Tang <dmosberger@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add NOTES to linker script such that the kernel can be built with
recent versions of binutils. Without this patch, final link fails
with this error:
ld: .tmp_vmlinux1: section `.text' can't be allocated in segment 0
ld: final link failed: Bad value
This error is due to the fact that the --build-id option is used
with newer linkers to include a .notes section on the kernel, but
without the NOTES macro, that section won't be included in the kernel
which then leads to the above error message.
Signed-off-by: David Mosberger-Tang <dmosberger@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a dummy nop at the end of _start() to maintain the invariant that
the return-pointer (rp) always point to the calling function. This
makes unwinding stop at the last frame, as it should.
Signed-off-by: David Mosberger-Tang <dmosberger@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use local_vector_to_irq() instead of looping through all NR_IRQS.
This avoids registering the CPE handler on multiple irqs. Only
register if the irq is valid. If no valid irq is found, print an
error message and set up polling.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/Kconfig failed to include kernel/Kconfig.preempt that meant it
did not support PREEMPT_VOLUNTARY and PREEMPT_BKL (inadvertently).
This was recently noticed when the newly-added PREEMPT_NOTIFIERS in
Kconfig.preempt that was "select"ed from drivers/kvm/Kconfig (therefore)
started giving bogus warnings ('select' used by config symbol 'KVM' refers
to undefined symbol 'PREEMPT_NOTIFIERS') on ia64 builds.
So let's remove the open-coded definition of CONFIG_PREEMPT in
arch/ia64/Kconfig and replace it with just including Kconfig.preempt
instead, like the other archs do.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The routines ia64_atomic64_{add,sub} mistakenly use
atomic_read() to grab the old value instead of using
atomic64_read().
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While sending interrupts to a cpu to repeatedly wake a thread, on occasion
that thread will take a full timer tick cycle (4002 usec in my case)
to wakeup.
The problem concerns a race condition in the code around the safe_halt()
call in the default_idle() routine. Setting 'nohalt' on the kernel
command line causes the long wakeups to disappear.
void
default_idle (void)
{
local_irq_enable();
while (!need_resched()) {
--> if (can_do_pal_halt)
--> safe_halt();
else
A timer tick could arrive between the check for !need_resched and the
actual call to safe_halt() (which does a pal call to PAL_HALT_LIGHT).
By the time the timer tick completes, a thread that might now need to run
could get held up for as long as a timer tick waiting for the halted cpu.
I'm proposing that we disable irq's and check need_resched again before
calling safe_halt(). Does anyone see any problem with this approach?
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Put a 1000 msec delay after resetting the device before attempting to
do config cycles on it. Not waiting causes system hangs on some
chipsets, e.g. Intel E7520, when the driver is loaded.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The smsc47m1 driver no longer creates the name attribute used by
libsensors to identify chip types. It was lost during the conversion
to a platform driver. I was fooled by the fact that we do have a
group with all attributes, but only to delete them all at once. The
group is not used to create the attributes, so we have to explicitly
create the name attribute.
This fixes lm-sensors ticket #2236:
http://lm-sensors.org/ticket/2236
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Don't assume that the default bank is 0. For one thing, we don't even
set it to 0 when the driver is loaded, so the initial state might be
different. For another, something (say, the BIOS) might access the chip
and leave with the bank set to something different, so assuming that
the bank value is 0 is not safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch forces the driver to read the fan divider values during early init.
Otherwise, a call to store_fan_min() could access uninitialized variables.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix following section mismatch warning:
WARNING: drivers/built-in.o(.text+0x73d0): Section mismatch: reference to .init.data: (between 'pxafb_setup' and 'pxafb_init')
The warning are caused by __devinit pxafb_setup() that refers to a
variable marked __initdata. In a hotplug scenario we would have a
reference to the freed .init.data section. Fix this by declaring
g_options __devinitdata.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 348753379a introduced a regression that
caused temp2 and temp3 sensor type settings to be written to temp1 instead.
The result is that temp sensor readings could be way off.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The b44 build uses these, caught by allmodconfig:
drivers/net/b44.c: In function `b44_sync_dma_desc_for_cpu':
drivers/net/b44.c:159: error: implicit declaration of function `dma_sync_single_range_for_cpu'
Follow the sparc64 change and stub them in.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that __initmv references the machvec section unconditionally
there have been cases where folks have been mistakenly flagging
non-machvec structures with the machvec section attribute (presumably
to shut up modpost). This leads to obscure breakage in earlyprintk
amongst other places and is rather non-obvious.
Add a simple sanity check to try and catch __initmv misuse and
panic early.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
(This is a resend of a patch originally submitted on 24-Jul-2007 00:14)
Ok, this is something the coverity checker found (CID: 1813).
I'm not at all intimate with this code, so I'm not sure if this
attempt at a fix is correct (but at least it compiles).
Please look it over and NACK if bad or merge if good ;-)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When generic_ptrace_peekdata() was merged, the break for these cases
ended up getting dropped, which lead to each PEEKTEXT/PEEKDATA op leaking
in to PEEKUSR and get_user_pages() always -EFAULTing. Add the break back
in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New Cisco IB SRP targets use the Cisco OUI 00-1b-0d but still need the
Topspin workarounds. Add this OUI to srp_target_is_topspin().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap the checking for Mellanox and Topspin OUIs to decide whether to
use a workaround into helper functions. This will make it cleaner to
add a new OUI to check (as we need to do now that some targets with a
Cisco OUI still need the Topspin workarounds).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After moving the definition of struct ib_umem_chunk from ib_verbs.h to
ib_umem.h there isn't any reason for the macro IB_UMEM_MAX_PAGE_CHUNK
to stay in ib_verbs.h. Move the macro to umem.c, the only place where
it is used.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_verbs.h uses struct list_head and rw_semaphore, so while the files
<linux/list.h> and <linux/rwsem.h> seem to be pulled in indirectly by
the other header files it includes, the right thing is to include
those files directly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_mad.h uses struct list_head, so while linux/list.h seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include linux/list.h directly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The address handle associated with dual-sided RMPP direction switch
ACKs is never destroyed. Free the AH for ACKs which fall into this
category.
Problem was reported by Dotan Barak <dotanb@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Nothing looks at the return value of agent_send_response(), so there's
no point in returning anything.
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If agent_send_response() returns an error, we shouldn't do anything
differently than if it succeeds; setting response to NULL just means
that the response buffer gets leaked.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_mad_recv_done_handler() fails to allocate response, then it just
printed a warning and continued, which leads to an oops if the MAD is
being handled for a switch device, because the switch code uses
response without checking for NULL. Fix this by bailing out of the
function if the allocation fails.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that ib_find_pkey() ignores the membership bit of P_Keys, there's no
need for ib_sa to look for both 0x7fff and 0xffff in a port's P_Key table.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_find_pkey() is used as a replacement for ib_find_cached_pkey(), and
the original function ignored the membership bit when searching for a
P_Key, so ib_find_pkey() should ignore the bit too.
In particular, IPoIB turns on the P_Key membership bit of limited
membership P_Keys when creating a child interface and looks for the
full membership P_key. This broke if a port was a partial member of a
partition when IPoIB switched from ib_find_cached_pkey() to
ib_find_pkey(), and this change fixes things again.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Caused by unneeded reopen during reconnect while spinlock held.
Fixes kernel bugzilla bug #7903
Thanks to Lin Feng Shen for testing this, and Amit Arora for
some nice problem determination to narrow this down.
Acked-by: Dave Kleikamp <shaggy@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch removes some obviously dead code spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
2007-07-23 18:29:41 +10:00
910 changed files with 16013 additions and 19703 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
