flagged_taskfile() is called from execute_drive_cmd()
(the only user) only if args->tf_out_flags.all != 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove duplicate documentation for ide_do_drive_cmd() from
<linux/ide.h>, this function is already documented in ide-io.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Daniel Jacobowitz
After delivering a signal (creating its stack frame) we must check for
additional pending unblocked signals before returning to userspace.
Otherwise signals may be delayed past the next syscall or reschedule.
Once that was fixed it became obvious that the ARM signal mask manipulation
was broken. It was a little bit broken before the recent SA_NODEFER
changes, and then very broken after them. We must block the requested
signals before starting the handler or the same signal can be delivered
again before the handler even gets a chance to run.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The result is mostly similar to the original ppc64 version but with
some adaptations for 32-bit compilation.
include/asm-ppc64 is now empty!
Signed-off-by: Paul Mackerras <paulus@samba.org>
This involves some minor changes: a few unused functions that the
ppc32 pci.c provides are no longer declared here or exported;
pcibios_assign_all_busses now just refers to the pci_assign_all_buses
variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now
just 0 instead of a function that always returns 0 on 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For these, I have just done the lame-o merge where the file ends up
looking like:
#ifndef CONFIG_PPC64
#include <asm-ppc/foo.h>
#else
... contents from asm-ppc64/foo.h
#endif
so nothing has changed, really, except that we reduce include/asm-ppc64
a bit more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/imalloc.h is only included from files in arch/powerpc/mm.
We already have a header for mm local definitions,
arch/powerpc/mm/mmu_decl.h. Thus, this patch moves the contents of
imalloc.h into mmu_decl.h. The only exception are the definitions of
PHBS_IO_BASE, IMALLOC_BASE and IMALLOC_END. Those are moved into
pgtable.h, next to similar definitions of VMALLOC_START and
VMALLOC_SIZE.
Built for multiplatform 32bit and 64bit (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trying to set the priority would just disable the interrupt due to an
incorrect mask used. We rarely use that call, in fact, I think only in
the powermac code for the cmd-power key combo that triggers xmon. So it
got unnoticed for a while.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sure that userspace passes in enough data when sending a MAD. We
always copy at least sizeof (struct ib_user_mad) + IB_MGMT_RMPP_HDR
bytes from userspace, so anything less is definitely invalid. Also,
if the length is less than this limit, it's possible for the second
copy_from_user() to get a negative length and trigger a BUG().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From: Amit Gud <amitg@calsoftinc.com>
Patch follows from the suggestions by AC and Felipe W Damasio for fixing the
return codes from IDE drivers.
[ bart: fix coding style while at it ]
Signed-off-by: Amit Gud <gud@eth.net>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Thibaut VARENE <T-Bone@parisc-linux.org>
Cleaning up the hwif without knowing its previous state in pmac.c is a big
and potentially dangerous job, and there seems to be no generic code interface
that would provide either a way to properly release an hwif or to clean it up.
Fixes OOPS for empty PMAC interface and add-on PCI controller.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These drivers do not compile on big endian systems, and parisc
is big endian. Also mark some as broken on m68k as well.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Mention PA-RISC in NS87415 help. PA-RISC [BCJ]xxx0 workstations come with
NS87415 integrated for their CD-ROM drives.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix compile warning caused by conflicting types of expand_upwards. IA64
requires it to not be static inline, as it's used outside mm/mmap.c
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The structure ide_driver_t have a .owner field which is a duplicate
of .gendriver.owner field (.gen_driver is a struct device_driver).
This patch removes ide_driver_t's owner field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support multiple controllers in the via82cxxx IDE driver.
Cable detection and ISA bridge finding have been moved into
their own functions.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This entry adds needless complication to the driver as it requires the use of
global variables to be passed into via_get_info(), making things quite ugly
when we try and make this driver support multiple controllers simultaneously.
This patch removes /proc/via for simplicity.
On 10/13/05, Daniel Drake <dsd@gentoo.org> wrote:
> Per Bart's suggestion, I've created a user-space app which shows identical
> data (and doesn't even rely on the via82cxxx IDE driver).
>
> http://www.reactivated.net/software/viaideinfo/
>
> So, I think we should be clear to drop /proc/ide/via now.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jeff Garzik pointed me to his code to see how to remove a disk from
the system _properly_. Well, here it is...
Every place we remove disks we are now testing before calling del_gendisk
or blk_cleanup_queue and then call put_disk.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Applications using CCISS_BIG_PASSTHRU complained that the data written
was zeros. The problem is that the buffer is being cleared after the
user copy, unless the user copy has failed... Correct that logic.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch fixes a bug that breaks hpacucli, a command line interface
for the HP Array Config Utility. Without this fix the utility will
not detect any controllers in the system. I thought I had already fixed
this, but I guess not.
Thanks to all who reported the issue. Please consider this this inclusion.
Signed-off-by: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <axboe@suse.de>
Some leftover comments referring to drivers/block that are now block/.
They don't add any information we don't already have, so kill them.
Signed-off-by: Coywolf Qi Hunt <qiyong@fc-cn.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
ipw2100: Fix 'Driver using old /proc/net/wireless...' message
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
A prior instance of this patch resolved the issue for the ipw2200.
This one fixes it for the ipw2100.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change CONFIG_FEC_8XX to depend on CONFIG_8xx instead of CONFIG_FEC.
CONFIG_FEC depends on ColdFire CPUs, which does not apply for the
PPC 8xx processors.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the index file with descriptions of the stable_api_nonsense.txt
and stable_kernel_rules.txt files.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a document that describes the process and procedures of how to do Linux
kernel development. It has gone through a number of rounds of review on the
linux-kernel mailing list, and contains contributions and help from Paolo
Ciarrocchi, Randy Dunlap, Gerrit Huizenga, Pat Mochel, Hanna Linder, Kay
Sievers, Vojtech Pavlik, Jan Kara, Josh Boyer, Kees Cook, Andrew Morton, Andi
Kleen, Vadim Lobanov, Jesper Juhl, Adrian Bunk, Keri Harris, Frans Pop, David
A. Wheeler, Junio Hamano, Michael Kerrisk, and Alex Shepard.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/net/ieee80211.h: In function `ieee80211_get_payload':
include/net/ieee80211.h:1046: warning: control reaches end of non-void function
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hermas_bap_pread, hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.
Thanks to LinuxICC (http://linuxicc.sf.net)
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In isl_38xx.c
In routine isl38xx_trigger-device
Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.
This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sil24_error_intr logs all error interrupts. ATAPI devices generates
many harmless errors which can be ignored and all serious ones are
reported via sense data by SCSI layer. Don't log device errors from
ATAPI devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ATAPI support for sil24 and bumps driver version
to 0.23.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, it has been converted to use ->dev_config as pointed out.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There seems to be no way to obtain device signature from sil24 after
SATA phy reset and SRST is needed anyway for later port multiplier
suppport. This patch converts sil24_phy_reset to use SRST instaed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, I didn't remove the 10ms sleep just to be on the safe side. I
think we can live with 10ms sleep on SRST.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When an error condition is raised by device via D2H FIS or SDB. sil24
controller should be restarted by setting PORT_CS_INIT and waiting
until PORT_CS_RDY is asserted instead of resetting the controller.
This patch implements sil24_restart_controller for those cases. This
patch also makes sure that PORT_CS_RDY is asserted on
sil24_reset_controller completion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, delay is reduced to 1us and cnt increased to 10k. My sil3124
turns on PORT_CS_RDY on the second iteration even without any delay.
I think 10k * 1us should be more than enough.
I tried to convert both restart and reset to use msleep's with work
queue, but if we do that, host_set lock should be released after
initiating restart or reset, leading to race condition among
reset/restart, other interrupts and timeout. Implementing
synchronization among those in low-level driver doesn't seem right.
Well, reduced timeout should work for the time being.
Thanks.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called. This isn't always so, especially if
we have a link change event during PHY configuration.
This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status. In turn, this causes us to spin with a
permanently asserted IRQ.
The patch ensures that smc_phy_configure always exits with register
bank 2 selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.
While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the missing NULL argument to the class_device_create calls.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the new powerpc architecture we don't seem to be able to disable huge
pages anymore.
mm/built-in.o(.toc1+0xae0): undefined reference to `HPAGE_SHIFT'
make: *** [.tmp_vmlinux1] Error 1
We seem to need to define HPAGE_SHIFT to something when HUGETLB_PAGE isn't
defined. This patch defines it to PAGE_SHIFT when we have no support.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md needs to monitor the rate of requests to its devices when doing
resync/recovery so that it can back-off when there is non-resync IO. It
does this by comparing resync IO, which it counts, with total IO which is
taken from disk_stats.
disk_stats were recently changed to account sectors when a request
completes instead of when it is queued. This upsets md's calculations.
We could do the sync_io accounting at the end of requests too, but that has
problems. If an underlying device is an md array, the accounting will
still be done when the request is submitted. This could be changed for
some raid levels, but it cannot be changed for raid0 or linear without
substantial code changes.
So instead, we increase the error that is_mddev_idle allows, up to the
maximum amount of resync IO that can be in flight at any time. The
calculation is current fragile as each personality as different limits for
in-flight resync. This should be fixed up.
For now, this simple patch fixes the problem.
Increasing the error margin decreases the sensitivity to non-resync IO. To
partially compensate for this, the time to wait when non-resync IO is
detected is increased so that less steady IO is required to keep the resync
at bay.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver dependencies on PCI have been removed. This patch clears that
up in the Kconfig file
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the necessary flush_schedule_work calls when canceling the timer.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On IPMI systems with BT interfaces, we don't start the kernel thread, so
smi_info->thread is NULL. Test for NULL when stopping the thread, because
kthread_stop() doesn't, and an oops ensues otherwise.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.14 has this exported, and reiser4 (at least) uses it. Put things back
the way they were.
Signed-off-by: Vladimir V. Saveliev <vs@namesys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One issue with the RCU torture test is that the current error flagging can
be lost in dmesg. This patch adds a "SUCCESS"/"FAILURE" string to the line
that flags the end of the test, where it can easily be seen with "dmesg |
tail" at the end of the test. Also adds tests of architecture-specific
memory barriers -- or, more likely, of the RCU torture test itself.
Cc: <vatsa@in.ibm.com>
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Properly clear the memory, and set "pr->flags.power" only if a C2 or
deeper state is valid (to make the code match both the comment and
previous behaviour).
This fixes a boot-time lockup reported by Maneesh Soni when using
"maxcpus=1".
Acked-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every other architecture define dma_cache_{inv,wback,wback_inv}
in asm/io.h and doing so brings us closer to ppc64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Unfortunately, later gcc versions error out when our get_user is passed
a const pointer, since we write to a temporary variable declared as
typeof(*(p)) which propagates the const-ness.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
make defconfig will now use arch/powerpc/configs/ppc64_defconfig
if running on a ppc64 system. I need to add an
arch/powerpc/configs/ppc_defconfig sometime.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 32-bit CHRP systems use the RTAS time-of-day routines if
available. It fixes a bug in the RTAS time-of-day routines where they
were storing a 64-bit timebase value in an unsigned long by making
those variables u64. Also, the direct-access time-of-day routines
had the wrong convention for the month and year in the struct rtc_time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also deletes the now-unused Makefiles under arch/ppc64.
Both of the files moved over could use some merging, but for now I
have moved them as-is and arranged for them to be used only in 64-bit
kernels. For 32-bit kernels we still use arch/ppc/kernel/idle.c and
drivers/char/generic_nvram.c as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config option SPAN_OTHER_NODES was created so that we could
make pSeries numa layouts work within the DISCONTIG memory model.
Now that DISCONTIG has been replaced by SPARSEMEM, we can eliminate
this option.
I'll be sending a separate patch to Andrew to remove the arch
independent code as pSeries was the only arch that needed this.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges align.c, the result isn't quite what was in ppc64 nor
what was in ppc32 :) It should implement all the functionalities of both
though. Kumar, since you played with that in the past, I suppose you
have some test cases for verifying that it works properly before I dig
out the 601 machine ? :)
Since it's likely that I won't be able to test all scenario, code
inspection is much welcome.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My earlier merge of delay.h introduced a timebase-based udelay for
32-bit machines but also broke the 601, which doesn't have the
timebase register. This fixes it by using the 601's RTC register on
the 601, and also moves __delay() and udelay() to be out-of-line in
arch/powerpc/kernel/time.c. These functions aren't really performance
critical, after all.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we moved things around in irq.h seq_file became an issue. Fix
warnings related to its usage.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SVRs for MPC8343/E were incorrect and really the SVRs
for MPC8347/E.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reserve the Maple RTC I/O resource. Needed now we use genrtc.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replacing the string labels with numbers saves 117 bytes in the final zImage.
These local labels are not discared.
Signed-off-by: Olaf Hering <olh@suse.de>
arch/powerpc/boot/crt0.S | 23 +++++++++++------------
1 files changed, 11 insertions(+), 12 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fix to topology.h (5cfccd7f13) seems to have
a typeo, struct sched_domain has an idle_idx member but not an idle_id
member. I assume this is the fix.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we moved things around in irq.h seq_file became an issue. Fix
warnings related to its usage.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Thu, 17 Nov 2005, David Gmez wrote:
> I found out that if i select NET_CLS_ROUTE4, save my changes and exit
> menuconfig, execute again make menuconfig and go to QoS options, then the new
> available options are visible. So menuconfig has some problem refreshing
> contents :?
No, they were there before too, but you have to go up one level to see
them.
It's better in 2.6.15-rc1-git5, but the menu structure is still a little
messed up, the patch below properly indents all menu entries.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Olaf Hering.
The comparisons want a u8 here (the data type on the left-hand branch
is a u8 structure member, and the constant on the right-hand branch is
"~((u8) 128)"), but C turns it into an integer so we get:
net/llc/llc_c_ac.c: In function `llc_conn_ac_inc_npta_value':
net/llc/llc_c_ac.c:998: warning: comparison is always true due to limited range of data type
net/llc/llc_c_ac.c:999: warning: large integer implicitly truncated to unsigned type
Fix this up by explicitly recasting the right-hand branch constant
into a "u8" once more.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we've converted the ftp/irc/tftp helpers to use the new
module_parm_array() some time ago, we ware accidentially using signed data
types - thus preventing those modules from being used on ports >= 32768.
This patch fixes it by using 'ushort' module parameters.
Thanks to Jan Nijs for reporting this bug.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So things like on-line resizing et al. work.
Based almost entirely upon a patch by Guido Gnther <agx@sigxcpu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document that the VMALLOC_END address must be aligned to 2MB since
it must align with a PGD boundary.
Allocate the vectors page early so that the flush_cache_all() later
will cause any dirty cache lines in the direct mapping will be safely
written back.
Move the flush_cache_all() to the second local_flush_cache_tlb() and
remove the now redundant first local_flush_cache_tlb().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a compile error that crept in with the last patch of
TCP patches.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert superio_init to use PCI_FIXUP_FINAL as ohci_pci being called
before superio_probe really makes a mess. superio_init will then fail
to register irq 20 (the "SuperIO" irq) and BUG() because ohci_pci has
stolen it before superio_fixup_irq can be moved USB to irq 1.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Since taking a spinlock disables preempt, and we need to spinlock tlb flush
on SMP for N class, we might as well just spinlock on uniprocessor machines
too.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Remove drm compat_ioctl handlers. The drm drivers have proper
compat_ioctl methods these days.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This commit is in response to a bug reported by Vesa on the irc channel
a couple of weeks ago.
The bug was that the console would apparently hang (not return) while
using the mux console.
The root cause of this bug is that bash (with readline support) makes a
call to the tcsetattr() glibc function with the argument TCSADRAIN. This
causes the serial core in the kernel use the uart_wait_until_sent() to be
called. This function verifies the mux transmit queue is empty or calls the
msleep_interruptable() with a calculated timeout value that is dependant
upon the port->timeout variable.
The real problem here is that the port->timeout was not defined so it
was defaulted to 0 and the timeout calculation performs the following
calculation:
char_time = (port->timeout - HZ/50) / port->fifosize;
where char_time is an unsigned long. Since the serial Mux does not use
interrupts, the msleep_interruptable() function waits until the timeout
has been reached ... and when the port->timeout < HZ/50 this timeout will
be a long time. (I have validated that the console will eventually
return ... but it takes quite a while for this to happen).
This patch simply sets the port->timeout on the Mux to HZ/50 to avoid
this long timeout period.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix some compile problems:
- ret wasn't being initialised in all code paths
- I'm pretty sure 'goto out' should have been 'goto out_tsk'
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch does the following:
* Fixes compiler warnings.
* Replaces a __raw_readl call with the existing macro.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We actually have two separate bad bugs
1. The read_lock implementation spins with disabled interrupts. This is
completely wrong
2. Our spin_lock_irqsave should check to see if interrupts were enabled
before the call and re-enable interrupts around the inner spin loop.
The problem is that if we spin with interrupts off, we can't receive
IPIs. This has resulted in a bug where SMP machines suddenly spit
smp_call_function timeout messages and hang.
The scenario I've caught is
CPU0 does a flush_tlb_all holding the vmlist_lock for write.
CPU1 tries a cat of /proc/meminfo which tries to acquire vmlist_lock for
read
CPU1 is now spinning with interrupts disabled
CPU0 tries to execute a smp_call_function to flush the local tlb caches
This is now a deadlock because CPU1 is spinning with interrupts disabled
and can never receive the IPI
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Improve the error message when we get a clashing mod path, and
actually display the IODC data and path for the conflicting device.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Return PDC_OK when device registration fails so that we enumerate all
subsequent devices, even when we get two devices with the same hardware
path (which should never happen, but does with at least one revision of
rp8400 firmware).
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Document clobbers and args in entry.S and syscall.S.
entry.S: Add comment to indicate that cr27 may recycle and EDEADLOCK
detection is not 100% correct. Since this is only enabled when using
ENABLE_LWS_DEBUG, the user is warned by the comment.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make the "redirecting irq" message to not display on the console by
setting the severity to KERN_DEBUG. The console was basically unusable.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
irq_affinityp[] only available for SMP builds, make code that uses
it conditional on CONFIG_SMP.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This really only adds them for the machines I can check SMP on, which
is CPU interrupts and IOSAPIC (so not any of the GSC based machines).
With this patch, irqbalanced can be used to maintain irq balancing.
Unfortunately, irqbalanced is a bit x86 centric, so it doesn't do an
incredibly good job, but it does work.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Since irq.c uses smp_send_all_nop, we must define it for UP builds
as well. Make it a static inline so it gets optimized away. This forces
irq.c to include <asm/smp.h> though.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix our interrupts not to use smp_call_function
On K and D class smp, the generic code calls this under an irq
spinlock, which causes the WARN_ON() message in smp_call_function()
(and is also illegal because it could deadlock).
The fix is to use a new scheme based on the IPI_NOP.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Disable nesting of interrupts - still has holes
The offending sequence starts out like this:
1) take external interrupt
2) set_eiem() to only allow TIMER_IRQ; local interrupts still disabled
3) read the EIRR to get a "list" of pending interrupts
4) clear EIRR of pending interrupts we intend to handle
5) call __do_IRQ() to handle IRQ.
6) handle_IRQ_event() enables local interrupts (I-Bit)
7) take a timer interrupt
8) read EIRR to get a new list of pending interrupts
9) clear EIRR of pending interrupts we just read
10) handle pending interrupts found in (8)
11) set_eiem(cpu_eiem) and return
[ TROUBLE! all enabled CPU IRQs are unmasked. }
12) handle remaining interrupts pending from (3)
e.g. call __do_IRQ() -> handle_IRQ_event()..etc
[ TROUBLE! call to handle_IRQ_event() can now enable *any* IRQ. }
13) set_eiem(cpu_eiem) and return
The problem is we now get into ugly race conditions with Timer and IPI
interrupts at this point. I'm not exactly sure what happens when
things go wrong (perhaps nest calls to IPI or timer interrupt?).
But I'm certain it's not good.
This sequence will break sooner if (10) would accidentally leave
interrupts enabled.
I'm pretty sure the right answer is now to make cpu_eiem
a per CPU variable since all external interrupts on parisc
are per CPU. This means we will NOT need to send an IPI to
every CPU in the system when enabling or disabling an IRQ
since only one CPU needs to change it's EIEM.
Thanks to James Bottomley for (once again) pointing out the problem.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix a longstanding smp bug
The problem is that both the timer and ipi interrupts are being called
with interrupts enabled, which isn't what anyone is expecting.
The IPI issue has just started to show up by causing a BUG_ON in the
slab debugging code. The timer issue never shows up because there's an
eiem work around in our irq.c
The fix is to label both these as SA_INTERRUPT which causes the generic
irq code not to enable interrupts.
I also suspect the smp_call_function timeouts we're seeing might be
connected with the fact that we disable IPIs when handling any other
type of interrupt. I've put a WARN_ON in the code for executing
smp_call_function() with IPIs disabled.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We must reassign z before looping through the zones kicking kswapd,
since it will be NULL if we hit an OOM condition and jump back to the
beginning again. 'z' is initially assigned before the restart: label. So
move the restart label up a little.
Signed-off-by: Jens Axboe <axboe@suse.de>
It was causing too many problems, and this is not the proper type of
driver for this device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lets us remove a lot of code in the drivers that were all checking
the same thing. It also found some bugs in a few of the drivers, which
has been fixed up.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an error in the OHCI lh7a404 driver after the platform device
conversion.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This small patch adds a device ID used by older Maxtor OneTouch drives
(the ones with blue face-plate instead of the fancy silver one used in
newer models). The button on those drives works well with the current
driver.
From: Antti Andreimann <Antti.Andreimann@mail.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch from Herbert Xu fixes a race by moving termination of
the URBs into close() exclusively.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Peter Favrholdt reported that his Kodak flash device was getting
detected as a CDROM, and he helped me track this down to the fact that
the device takes a long time (approx 440ms!) to reset.
This patch increases the delay to 500ms, which solves the problem.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the scsi layer now uses very short sg lists. This breaks the microtek
driver. Here is a patch fixes this and some other issues.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The onetouch support doesn't suspend correctly (leaves an interrupt
URB posted, instead of unlinking it) so for now just disable it
when PM is in the air.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I actually have this device, and kernel reports blacklist entry is no
longer neccessary.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast
NFI if this is correct...
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch deletes the bluetooth.txt help file of the bluetty driver and
hands over its major device nodes for character devices to the RFCOMM TTY
implementation of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
People are complaining about a .old file in the tree. So rename
drivers/usb/serial/ChangeLog.old to ChangeLog.history.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Polish the comments specifically in vhpt_miss and nested_dtlb_miss
handlers. I think it's better to explicitly name each page table
level with its name instead of numerically name them. i.e., use
pgd, pud, pmd, and pte instead of referring as L1, L2, L3 etc.
Along the line, remove some magic number in the comments like:
"PTA + (((IFA(61,63) << 7) | IFA(33,39))*8)". No code change at
all, pure comment update. Feel free to shoot anything you have,
darts or tomahawk cruise missile. I will duck behind a bunker ;-)
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
From source code inspection, I think there is a bug with 4 level
page table with vhpt_miss handler. In the code path of rechecking
page table entry against previously read value after tlb insertion,
*pte value in register r18 was overwritten with value newly read
from pud pointer, render the check of new *pte against previous
*pte completely wrong. Though the bug is none fatal and the penalty
is to purge the entry and retry. For functional correctness, it
should be fixed. The fix is to use a different register so new
*pud don't trash *pte. (btw, the comments in the cmp statement is
wrong as well, which I will address in the next patch).
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The "align" argument in ARMs __ioremap is unused and provides a
misleading expectation that it might do something. It doesn't.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__ioremap is an architecture private interface and must not be used
by drivers when the architecture independent interface will do just
as well. Switch the ipaq drivers to use the correct interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to incomplete memory constraints, gcc would miscompile code with
sigaddset on i386 if sig arg was const.
A quote form Jakub to make the issue clear:
"You need either
__asm__("btsl %1,%0" : "+m"(*set) : "Ir"(_sig-1) : "cc");
or
__asm__("btsl %1,%0" : "=m"(*set) : "Ir"(_sig-1), "m"(*set) : "cc");
because the btsl instruction doesn't just set the memory to some
value, but needs to read its previous content as well. If you don't
tell that fact to GCC, GCC is of course free to optimize as if the asm
was just setting the value and not depended on the previous value."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).
Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--
The function ipw_request_direct_scan() should bail out when the device
is down. This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.
Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no definition for seadint_init() and the unprotected prototype
breaks compilation of assembler files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver supports the IDE port on the Sibyte Swarm evaluation boards
and it's relatives for the BCM1250 family of systems on a chip.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Not that it's meant to be sustained for long, but from time to time it's
useful to have some console...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 8250 serial driver now has the ability to deal with the differences
between the standard 8250 family of UARTs and their slightly strange
brother on Alchemy SOCs. The loss of features is not considered an
issue.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Handle errata (it was unintentional on this h/w, whereas its intentional
on others) whereby the nIEN bit in Device Control is ignored, leading to
a situation where a hardware interrupt completes the qc before the
polling code has a chance to.
This will get fixed The Right Way(tm) once Albert Lee's irq-pio
branch is merged, as the more natural PIO method on this hardware is
interrupt-driven.
- DMA boundary was being handled incorrectly. Copied the code from
ata_fill_sg(), since Marvell has the same DMA boundary needs.
(we can't use ata_fill_sg directly since we have different hardware
descriptors)
- cleaned up the SATA phy reset code, to deal with various errata
CC [M] net/netfilter/nf_conntrack_core.o
net/netfilter/nf_conntrack_core.c: In function 'nf_ct_unlink_expect':
net/netfilter/nf_conntrack_core.c:390: error: 'exp_timeout' undeclared (first use in this function)
net/netfilter/nf_conntrack_core.c:390: error: (Each undeclared identifier is reported only once
net/netfilter/nf_conntrack_core.c:390: error: for each function it appears in.)
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem with offb not parsing addresses properly on 64 bits
machines, and thus crashing at boot. The problem is worked around by
locating the matching PCI device and using the properly relocated PCI
base addresses instead of misparsing the Open Firmware properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC's NUMA domain doesn't currently set up some of the newer
sched-domains parameters.
Brian Twichell <tbrian@us.ibm.com> discovered and diagnosed a 1.5% OLTP
database regression on a 4 core POWER5 system that was due to the use of
NUMA scheduling on ppc64.
This patch applies some saneish values to the parameters, in line with
other architectures. This solves the regression.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The capabilities of the 8169 can be disabled but it is hardly a reason
to prevent the use the device. The (so far) unusual behavior has been
reported on a MIPS platform by Yoichi Yuasa.
Spotted-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I keep on getting "printk: N messages suppressed" messages. We need to test
netif_msg_intr() _before_ running printk_ratelimit(), because the latter
updates state.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Both of ipq and frag_queue have *next and **prev, and they can be replaced
with hlist. Thanks Arnaldo Carvalho de Melo for the suggestion.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are currently unable to fix the problem with carrier and protocol
state signaling in net core I've to disable netif_carrier_off()
calls used by WAN protocol drivers. The attached patch should make
them working again.
The remaining netif_carrier_*() calls in hdlc_fr.c are fine as they
don't touch the physical device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the old days when arm26/arm32 was combined into the same
architecture, proc-fns.h provided the xchg implementation for
arm26 CPUs. Since we no longer combine these two, this include
is no longer required. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since atomic.h does not include types.h, u32 may not be defined.
Since atomics are supposed to work on unsigned long quantities,
use unsigned long instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, using PAGE_SHIFT in asm/arch/memory.h is unsafe, and we
can't include asm/page.h into this file because then we have a circular
dependency. Move the offending code to arch/arm/common/sa1111.c
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
atomic.h, bitops.h and mmu_context.h are using likely/unlikely.
thread_info.h uses __attribute_const__. Hence these files require
linux/compiler.h to be included.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Minor changes, including add SysRq, selecting the DM9000
as a built-in driver, not as a module, and selecting the
framebuffer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Make the use of , on the lsat entry structs consistenent
through arch/arm/mach-s3c2410/mach-bast.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
If 'old' and 'oldval' are different then 'res' never gets set. In that
case, if ever %0 happened to contain anything but zero (rather likely)
then the code will loop forever (or until another CPU just come along
and change the atomic value to match 'old' which is rather unlikely).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we want new platforms to use debug-macro.S, make the decompressor
debugging method default to using this include file rather than having
new platforms add to an #if defined().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move __io_address to arch-realview/hardware.h, drop core.h from platsmp.c
and localtimer.c, and include asm/io.h where required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ATA devices don't generate many errors, so the preferred method is to
printk() when they occur.
ATAPI devices generate tons of exceptions during the normal course
of operation, so this change skips logging the most common class of
errors.
The following code segment is not functional because the transfer cycle time speficied by
the EIDE device is later overwritten by ata_timing_quantize():
/*
* If the drive is an EIDE drive, it can tell us it needs extended
* PIO/MW_DMA cycle timing.
*/
if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
memset(&p, 0, sizeof(p));
(snip)
ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
<== uninitialized "t" is used here
}
/*
* Convert the timing to bus clock counts.
*/
ata_timing_quantize(s, t, T, UT); <== t is overwritten by quantized s
The patch has been submitted for ide-timing.h before:
http://marc.theaimsgroup.com/?l=linux-ide&m=110820013425454&w=2
Resubmitted for libata.
Changes:
- Minor fix to honor the following transfer cycle time speficied by the device
- id[65]: Minimum Multiword DMA transfer cycle time per word
- id[67]: Minimum PIO transfer cycle time without flow control
- id[68]: Minimum PIO transfer cycle time with IORDY
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=======
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adds constants for ATAPI support to sata_sil24. This patch is
originally from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Based upon a patch by Guido Guenther <agx@sigxcpu.org>.
Some of these ioctls had embedded time_t objects
or pointers, so needed translation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the version when ENABLE_RC is defined, falls through
to the end of the function without returning anything.
Signed-off-by: David S. Miller <davem@davemloft.net>
The vDSO functions should have the same calling convention as a syscall.
Unfortunately, they currently don't set the cr0.so bit which is used to
indicate an error. This patch makes them clear this bit unconditionally
since all functions currently succeed. The syscall fallback done by some
of them will eventually override this if the syscall fails.
This also changes the symbol version of all vdso exports to make sure
glibc can differenciate between old and fixed calls for existing ones
like __kernel_gettimeofday.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building ARCH=ppc for multiplatforms with CONFIG_CHRP not set fails
due to some unshielded code in xmon
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also extends the code to handle 32-bit ELF vmlinux files as well
as 64-bit ones. This is sufficient for booting on new-world 32-bit
powermacs (i.e. all recent machines).
Signed-off-by: Paul Mackerras <paulus@samba.org>
page_to_virt and lowmem_page_address provided equiavlent functionality
so use the more standard lowmem_page_address
This also addresses build issue in ARCH=powerpc since page_to_virt()
has been removed from include/asm-powerpc/page.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hi,
The previous PowerBook patch didn't contain the feature table updates
for ARCH=powerpc. Here they are.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merge of machine types broke boot with yaboot & ARCH=ppc due to the
old code still retreiving the old-syle machine type passed in by yaboot.
This patch fixes it by translating those old numbers. Since that whole
mecanism is deprecated, this is a temporary fix until ARCH=ppc uses the
new prom_init that the merged architecture now uses for both ppc32 and
ppc64 (after 2.6.15)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ever since suspend to disk works I had the problem that headphone
(un)plugging doesn't get detected properly anymore after the first
resume.
Reloading the module worked around this ever since, however the real
cause of the problem was that after a resume the driver only got
interrupts on "unplug" not on "plug". Reactivating the headphone status
interrupt in tumbler_resume fixes this. This shouldn't cause
any trouble with software suspend, but it would be nice if somebody
could confirm this:
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.
This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somewhere we lost the include of udbg.h in lmb.c. While we're there, add a DBG
macro like every other file has and use it in lmb_dump_all().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch moving ppc64 RTC to genrtc was supposed to update all
defconfigs, but for some reason, the patch actually posted only had the
pseries one... ouch. This patch properly updates all defconfigs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently 8xx fails to boot due to endless pagefaults.
Seems the bug is exposed by the change which avoids flushing the
TLB when not necessary (in case the pte has not changed), introduced
recently:
__handle_mm_fault():
entry = pte_mkyoung(entry);
if (!pte_same(old_entry, entry)) {
ptep_set_access_flags(vma, address, pte, entry, write_access);
update_mmu_cache(vma, address, entry);
lazy_mmu_prot_update(entry);
} else {
/*
* This is needed only for protection faults but the arch code
* is not yet telling us if this is a protection fault or not.
* This still avoids useless tlb flushes for .text page faults
* with threads.
*/
if (write_access)
flush_tlb_page(vma, address);
}
The "update_mmu_cache()" call was unconditional before, which caused the TLB
to be flushed by:
if (pfn_valid(pfn)) {
struct page *page = pfn_to_page(pfn);
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
if (vma->vm_mm == current->active_mm) {
#ifdef CONFIG_8xx
/* On 8xx, cache control instructions (particularly
* "dcbst" from flush_dcache_icache) fault as write
* operation if there is an unpopulated TLB entry
* for the address in question. To workaround that,
* we invalidate the TLB here, thus avoiding dcbst
* misbehaviour.
*/
_tlbie(address);
#endif
__flush_dcache_icache((void *) address);
} else
flush_dcache_icache_page(page);
set_bit(PG_arch_1, &page->flags);
}
Which worked to due to pure luck: PG_arch_1 was always unset before, but
now it isnt.
The root of the problem are the changes against the 8xx TLB handlers introduced
during v2.6. What happens is the TLBMiss handlers load the zeroed pte into
the TLB, causing the TLBError handler to be invoked (thats two TLB faults per
pagefault), which then jumps to the generic MM code to setup the pte.
The bug is that the zeroed TLB is not invalidated (the same reason
for the "dcbst" misbehaviour), resulting in infinite TLBError faults.
The "two exception" approach requires a TLB flush (to nuke the zeroed TLB)
at each PTE update for correct behaviour:
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch should fix the crashes we have been seeing on 64-bit
powerpc systems with a memory hole when sparsemem is enabled.
I'd appreciate it if people who know more about NUMA and sparsemem
than me could look over it.
There were two bugs. The first was that if NUMA was enabled but there
was no NUMA information for the machine, the setup_nonnuma() function
was adding a single region, assuming memory was contiguous. The
second was that the loops in mem_init() and show_mem() assumed that
all pages within the span of a pgdat were valid (had a valid struct
page).
I also fixed the incorrect setting of num_physpages that Mike Kravetz
pointed out.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Although the comment around the allocation code tells us that
the layer-3 specific protocol tables will be freed when cleaning up,
they aren't. And this makes nfsim complain loudly...
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix nf_conntrack statistics proc file removal. Looks like the old bug
was forward-ported from ip_conntrack. :-]
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our performance validation on 2.6.15-rc1 caught a disastrous performance
regression on ia64 with netperf (-98%) and volanomark (-58%) compares to
previous kernel version 2.6.14-git7. See the following chart (result
group 1 & 2).
http://kernel-perf.sourceforge.net/results.machine_id=26.html
We have root caused it to commit 64c7c8f885
This changeset broke the ia64 task resched notification. In
sched.c:resched_task(), a reschedule IPI is conditioned upon
TIF_POLLING_NRFLAG. However, the above changeset unconditionally set
the polling thread flag for idle tasks regardless whether pal_halt_light
is in use or not. As a result, resched IPI is not sent from
resched_task(). And since the default behavior on ia64 is to use
pal_halt_light, we end up delaying the rescheduling task until next
timer tick, and thus cause the performance regression.
This fixes the performance bug. I'm glad our performance suite is
turning up bad performance bug like this in time.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids a BUG_ON with kref.c when SA1111 tries to register
a driver with an unregistered bus type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Fix a regression in command completion, which prevented
the restart of the DMA engine after the device throws
an error.
- Pack more hardware info into the port-reset error message.
- Promote "welcome to our timeout" message from debug msg
to normal printk.
Picked from the ubuntu-2.6 tree
The change in location for ll_rw_blk.c from drivers/block/ to block/ caused
failure to generate documentation.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/block/cciss_scsi.c:264: warning: `print_bytes' defined but not used
drivers/block/cciss_scsi.c:298: warning: `print_cmd' defined but not used
Signed-off-by: Grant Coady <gcoady@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A variable was being used in multiple conflicting ways. I also restructured
the code a bit for clarity.
Signed-off-by: Miles Bader <miles@gnu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use the USB_DEVICE macro here, else the modinfo aliases go all wrong.
Also, correctly terminate the table, as noted by Dave Jones <davej@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Despite the fact that md threads don't need to be signalled, and won't
respond to signals anyway, we need to have an 'interruptible' wait, else
they stay in 'D' state and add to the load average.
(akpm: the signal_pending() test is unneeded - we'll fix that up in the next
round. For now, leave it there because that's how the code used to be).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was marked deprecated "after 2.6" back in the 2.5 days. But now it
seems there isn't going to be any "after 2.6", and we deprecate by date
now. So set a date.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being kernel-threads, nfsd servers don't get pre-empted (depending on
CONFIG). If there is a steady stream of NFS requests that can be served
from cache, an nfsd thread may hold on to a cpu indefinitely, which isn't
very friendly.
So it is good to have a cond_resched in there (just before looking for a
new request to serve), to make sure we play nice.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lots of good changes to the driver lately that userspace will care about
the version of the driver. Bump the version from 36.0 to 38.0 to be higher
than 37 that the 2.4 driver came out with a few weeks ago which doesn't
have all the same changes.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A patch by Eric was merged (f2b36db692)
and later on reverted back (1e4c85f97f).
Along with above patch, another patch was posted and has been merged
(3d1675b41b). That patch was dependent on
the above patch and now it should also be reverted.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than defining our own PM option, use kernel/power/Kconfig.
This fixes build errors introduced by
bca73e4bf8
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Responder resources are only required to handle RDMA reads and atomic
operations, not RDMA writes. So the driver should allow RDMA writes
even if responder resources are set to 0. This is especially
important for the UC transport -- with the old code, it was impossible
to enable RDMA writes for UC QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Have __srp_get_tx_iu() fail if the target port's request limit will
not allow the initiator to post a send. This avoids continuing on and
posting a receive, and then failing to post a corresponding send. If
that happens, then the initiator will end up with an extra receive
posted, and if this happens to much, the receive queue will overflow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch below fixes the following sparse warning:
net/ipv6/ipv6_sockglue.c:291:13: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "score.rule++" doesn't make any sense for me.
According to codes above, I think it should be "hiscore.rule++;" .
Signed-off-by: Yan Zheng<yanzheng@21cn.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up booting with sparse mem enabled. Otherwise it would just
cause an early PANIC at boot.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for large multinode IBM systems which have a sparse
APIC space in clustered mode, fully covering the available 8 bits.
The previous kernels would limit the local APIC number to 127,
which caused it to reject some of the CPUs at boot.
I increased the maximum and shrunk the apic_version array a bit
to make up for that (the version is only 8 bit, so don't need
an full int to store)
Cc: Chris McDermott <lcm@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.
This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.
Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.
setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.
This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.
The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.
The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On x86_64 arches, there is no way to choose ACPI_NUMA without having to choose
K8_NUMA. CONFIG_K8_NUMA is not needed for Intel EM64T NUMA boxes. It also
looks odd if you have to select ACPI_NUMA from the power management menu.
This patch fixes those oddities. Patch does the following:
1. Makes NUMA a config option like other arches
2. Makes topology detection options like K8_NUMA dependent on NUMA
3. Choosing ACPI NUMA detection can be done from the standard
"Processor type and features" menu
AK: I fixed up the dependencies and changed the help texts a bit
on top of Kiran's patch.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time. The only difference is that now.tv_sec (which is
a time_t, i.e. a 64-bit long) is copied (and truncated) into a int
(32-bit).
The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).
Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current value was correct before the introduction of Intel EM64T support -
but now L1_CACHE_SHIFT_MAX can be less than L1_CACHE_SHIFT, which _is_ funny!
Between the few users of ____cacheline_maxaligned_in_smp, we also have (for
example) rcu_ctrlblk, and struct zone, with zone->{lru_,}lock. I.e. we have
a lot of excess cacheline bouncing on them.
No correctness issues, obviously. So this could even be merged for 2.6.14
(I'm not a fan of this idea, though).
CC: Andi Kleen <ak@suse.de>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not needed since x86-64 always uses the spinlock based rwsems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
B stepping were the first shipping Opterons. memcpy/memset/copy_page/
clear_page had special optimized version for them. These are really
old and in the minority now and the difference to the generic versions
(using rep microcode) is not that big anyways. So just remove them.
TODO: figure out optimized versions for Intel Netburst based EM64T
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old code could retry for 10 seconds worst time. Only try it
for one second now.
Suggested by Yinghai Lu
Cc: Yinghai.Lu@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the Intel cache detection code assumption that number of threads
sharing the cache will either be equal to number of HT or core siblings.
This also cleans up the code in general a bit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When they were disabled before (e.g. after a panic) it's better
to keep them off, otherwise followon panics can happen from timer
interrupt handlers etc.
Drawback is that pageup in the console won't work anymore though.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So far all new ones have worked and there isn't much variation because
the CPU does all the interesting bits.
So enable try unsupported by default.
Can be still disabled with try_unsupported=0 (module) or
amd64.try_unsupported=0 (boot option)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.
Before the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 23 for the hash shift. Max adder is 3ffffffff
After the patch :
Node 0 MemBase 0000000000000000 Limit 00000001ffffffff
Node 1 MemBase 0000000200000000 Limit 00000003ffffffff
Using 33 for the hash shift.
In this case, only 2 bytes of memnodemap[] are used, instead of 2048
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows to run 64bit signal handlers in 64bit processes that run small
code snippets in compat mode.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Cc: ashok.raj@intel.com
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I got some questions on this, so just fix up the documentation.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor victory on the continuous quest against all stray extern.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is for physical addresses, not for PFNs.
Pointed out by Tejun Heo.
Cc: htejun@gmail.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not go from the CPU number to an mapping array.
Mode number is often used now in fast paths.
This also adds a generic numa_node_id to all the topology includes
Suggested by Eric Dumazet
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to cpuid instruction in IA32 SDM-Vol2, when computing cpu model,
we need to consider extended model ID for family 0x6 also.
AK: Also added fixes/simplifcation from Petr Vandrovec
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicate __cpuinit in smp.c. Already defined in init.h which is
already included.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Has been introduced for x86-64 at some point to save memory
in struct page, but has been obsolete for some time. Just
remove it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pfn_to_page really requires pfn_valid to be true now, no question.
Some people stumbled over it, but it was misleading and wrong.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
AK: added some ifdefs to make it compile on UP
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code should deal with an additional empty zone, so fix up the
#error.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 traditionally had a 4GB DMA32 zone. Set the compatibility flag
to keep old drivers working.
For new drivers it would be better to use ZONE_DMA32 now.
Cc: tony.luck@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Gary Byers, we were clearing the image of the FPSCR
(floating point status and control register) in the thread_struct before
copying it to the user stack when invoking a signal. Thus the task
would see its FPSCR getting cleared when it took a signal.
While fixing it I noticed that our swapcontext system call was also
clearing FPSCR. It shouldn't, so I fixed that too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes nf_conntrack_ipv6 free all IPv6 fragment queues at module
unloading time. Also introduce a BUG_ON if we ever again have leaks in
the memory accounting.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This synchronizes nf_ct_reasm with ipv6 reassembly, and fixes a possibility
of an infinite loop if CPUs evict and create nf_ct_frag6_queue in parallel.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes linux 2.4 configs in comments as TODO lists.
And this also move the entry of nf_conntrack to top like IPv4 Netfilter
Kconfig.
Based on original patch by Krzysztof Piotr Oledzki <ole@ans.pl>.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Staticaly linked nf_conntrack_ipv4 requires nf_conntrack. but currently
nf_conntrack is linked after it. This changes the order of ipv4 and netfilter
to fix this.
Signed-off-by: Krzysztof Oledzki <olenf@ans.pl>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unconditionally requires CAP_NET_ADMIN for all nfnetlink
messages. It also removes the per-message cap_required field, since all
existing subsystems use CAP_NET_ADMIN for all their messages anyway.
Patrick McHardy owes me a beer if we ever need to re-introduce this.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the nf_conntrack TCP code was slightly mismerged: it does
not contain an else branch present in the IPv4 version. Let's add that
code and make the testsuite happy.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make gcc-4.x happy. Use size_t instead of int. Thanks to Patrick McHardy
for the hint.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move ATAPI check-condition handling out of the timeout handler
- Use multi-qc-issue feature to issue REQUEST SENSE ATAPI PACKET
command upon receiving an ATAPI check-condition.
This cleans things up a lot, and eliminates a nasty recursion bug.
- in ata_dev_identify(), don't assume that all devices are either
ATA or ATAPI. In the future, this code will see port multipliers
and other devices.
- make a debugging printk less verbose
- add new helper ata_qc_reinit()
- add new helper BPRINTK() and port flag ATA_FLAG_DEBUGMSG, for
fine-grained debugging use.
The ATAPI pad-to-next-32bit-boundary code modifies the scatterlist's
length variable, sometimes to zero. x86-64 platform would oops if a
zero-length scatterlist entry was asked to be mapped. Work around this
by ensuring that we never DMA-map a zero length buffer or SG entry.
Needed to get ATAPI working.
- dump hardware error bits, if hardware signals an error
- only reset hardware during timeout if a command was active
- call ata_qc_complete() with a fine-grained error mask.
Needed so that atapi_qc_complete() can distinguish between
device errors and other errors.
These machines don't have working ARCH=powerpc support yet, so make
them depend on BROKEN so people don't enable them inadvertently and
get compile errors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
... and also delete some that are no longer used because we already
had an include/asm-powerpc version of the header.
Signed-off-by: Paul Mackerras <paulus@samba.org>
log_plpar_hcall_return is only used on PPC_PSERIES, so move
it closer to its users and inside ifdef CONFIG_PPC_PSERIES.
remove the last vestiges of systemcfg in iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This moves the rtas RTC callbacks to rtas-rtc.c in arch/powerpc/kernel,
and kills the rest of arch/ppc64/kernel/rtc.c which was just a duplicate
of the genrtc functionality. Also enable build of genrtc for
CONFIG_PPC64 (it just works are we already have the required callbacks)
and enable it in all defconfigs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various errors in the new functions added in the vDSO's,
I've now verified all functions on both 32 and 64 bits vDSOs. It also
fix a sign extension bug getting the initial time of day at boot that
could cause the monotonic clock value to be completely on bogus for
64 bits applications (with either the vDSO or the syscall) on
powermacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch uses a FORCE dependency on the arch/powerpc/include/asm
symlink so that it always gets rebuilt, thus avoiding all sort of funny
errors if the .config is changed between 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The userspace kexec-tools need to know the location of the htab on non-lpar
machines, as well as the end of the kernel. Export via the device tree.
NB. This patch has been updated to use "linux,x" property names. You may
need to update your kexec-tools to match.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc/page.h and asm-ppc64/page.h into asm-powerpc/page.h,
asm-powerpc/page_32.h and asm-powerpc/page_64.h
Built for PPC (common_defconfig), with ARCH=powerpc, mostly built with
ARCH=ppc (other things break the build). Built and booted on P5 LPAR
for PPC64 with ARCH=ppc/powerpc (pseries_defconfig). Mostly built for
iSeries powerpc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As xmlto doesn't work for print documentation, we need docbook-utils again for
these targets.
This patch allows the user to choose the method he wants to use. (I'm still
hoping that someone will fix passivetex ;-)
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many structures contain both an internal part and one which is part of the API
to other modules. With this patch it is possible to only include these public
members in the kernel documentation.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merged parts of a patch from Takashi Iwai for an older version of the module.
This patch was adapted and tested by Ricardo Cerqueira.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This breaks compilation on non-x86 architectures, and isn't even used.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch caused some duplicated code in cx88-dvb.c:
[PATCH] v4l: 634: implemented tuner set standby on cx88 init
The cx88-dvb.c portion of this patch was already applied
in an earlier patch, entitled:
[PATCH] v4l: fixup on cx88_dvb for Dvico HDTV5 Gold
I love quilt and all, but AFAIK, no tool is 100% perfect for catching
oversights like this.
The non-overlapping portions of each of these patches are still needed, and
must not be discarded, so rather than reverting old patches, please just apply
this fixup patch to remove the duplicated code.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the code that avoids repeating events when pressing IR keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- saa7134-oss is now a standalone module as well
- remaining DMA sound code has been removed from core the module
- Lots of small cleanups and variable renames to get more consistency
between the OSS and ALSA drivers
- Fixed saa7134-alsa spinlock bug
- Added missing #include in saa7134-oss
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The pinnacle handler & remote are common to saa7134 PCI boards and em28xx
USB boards, so the keymap was moved to ir-common and the keyhandler is back
to ir-kbd-i2c
- request_module("ir-kbd-i2c") is no longer necessary at saa7134-core since
saa7134.ko now depends on ir-kbd-i2c.ko to get the keyhandler
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added SECAM L' video standard
- SECAM L' is a Secam variant that requires special config.
This patch adds support on V4L core. Requires aditional patches
on tuners to support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It would appear that the timespec normalize code has an off by one error.
Found in three places. Thanks to Ben for spotting.
Signed-off-by: George Anzinger<george@mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_work() to avoid down()-in-timer-handler problem.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the patch to support TPMs on power ppc hardware. It has been
reworked as requested to remove the need for messing with the io page mask
by just using ioremap.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some work is needed in the tpm device driver to discover the TPM out of the
device tree rather than based on set address on Power PPC. This patch
exports a couple of functions for the parsing.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
allnoconfig:
In file included from fs/super.c:28:
include/linux/acct.h:173: warning: `TICK_NSEC' is not defined
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
put_ioctx's refcount debugging was doing an atomic_read after dropping its
reference when it wasn't the last ref, leaving a tiny race for another freeing
thread to sneak into. This shifts the debugging before the ops, uses BUG_ON,
and reformats the defines a little. Sadly, moving to inlines increased the
code size but this change decreases the code size by a whole 9 bytes :)
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sync iocbs have a life cycle that don't need a kioctx. Their retrying, if
any, is done in the context of their owner who has allocated them on the
stack.
The sole user of a sync iocb's ctx reference was aio_complete() checking for
an elevated iocb ref count that could never happen. No path which grabs an
iocb ref has access to sync iocbs.
If we were to implement sync iocb cancelation it would be done by the owner of
the iocb using its on-stack reference.
Removing this chunk from aio_complete allows us to remove the entire kioctx
instance from mm_struct, reducing its size by a third. On a i386 testing box
the slab size went from 768 to 504 bytes and from 5 to 8 per page.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes deadlock of stop_machine() vs. synchronous IPI send. The
problem is that stop_machine() disables interrupts before disabling
preemption on other CPUs. So if another CPU is preempted and then calls
something like flush_tlb_all() it will deadlock with CPU doing
stop_machine() and which can't process IPI due to disabled IRQs.
I changed stop_machine() to do the same things exactly as it does on other
CPUs, i.e. it should disable preemption first on _all_ CPUs including
itself and only after that disable IRQs.
Signed-off-by: Kirill Korotaev <dev@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Andrey Savochkin" <saw@sawoct.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce an atomic_inc_not_zero operation. Make this a special case of
atomic_add_unless because lockless pagecache actually wants
atomic_inc_not_negativeone due to its offset refcount.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Make cmpxchg generally available on the i386 platform.
- Provide emulation of cmpxchg suitable for uniprocessor if built and run on
386.
From: Christoph Lameter <clameter@sgi.com>
- Cut down patch and small style changes.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the box usable for interactive work when running the RCU torture test,
by renicing the RCU torture-test threads to +19 by default. Kthreads run
at nice -5 by default.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently per_cpu_ptr() doesn't really do anything with 'cpu' in the UP
case. This is problematic in the cases where this is the only place the
variable is referenced:
CC kernel/workqueue.o
kernel/workqueue.c: In function `current_is_keventd':
kernel/workqueue.c:460: warning: unused variable `cpu'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update synclink to use DMA mapping API. This removes warning about
isa_virt_to_bus() usage on architectures other than i386
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes lost referrence on ext3 current handle in
ext3_journalled_writepage().
Signed-Off-By: Denis Lunev <den@sw.ru>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The access_ok_tt() macro is bogus, in that a read access is unconditionally
considered valid.
I couldn't find in SCM logs the introduction of this check, but I went back to
2.4.20-1um and the definition was the same.
Possibly this was done to avoid problems with missing set_fs() calls, but
there can't be any I think because they would fail with SKAS mode.
TT-specific code is still to check.
Also, this patch joins common code together, and makes the "address range
wrapping" check happen for all cases, rather than for only some.
This may, possibly, be reoptimized at some time, but the current code doesn't
seem clever, just confused.
* Important: I've also had to change references to access_ok_{tt,skas} back to
access_ok - the kernel wasn't that happy otherwise.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were using a long series of (stupid) wrappers which all call
generic_console_write(). Since the wrappers only change the 4th param, which
is unused by the called proc, remove them and call generic_console_write()
directly.
If needed at any time in the future to reintroduce this stuff, the member
could be moved to a generic struct, to avoid this duplicated handling.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk clears the host errno (I verified this in debugging and it's reasonable
enough, given that it ends via a write call on some fd, especially since
printk() goes on /dev/tty0 which is often the host stdout). So save errno
earlier. There's no reason to change the printk calls to use -err rather than
errno - the assignment can't clear errno.
And in the first failure path, we used to return 0 too (and this time more
clearly), which is totally wrong. 0 is a success fd, which is then registered
and gives a "registering fd twice" warning.
Finally, fix up some whitespace.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few fixups - show the new submenu only for x86 subarchitecture (it does not
make sense to show it for x86_64 users) and remove X86_CMPXCHG, which is now a
duplicate of Kconfig.i386, even though Kconfig doesn't complain (we also miss
the dependency on !M386 CPU).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove a stone-age comment (UM *does* have a MMU, i.e. the host), and fix a
dependency (introduced in commit 02edeb586a) to
do what was intended.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The below warning was added in place of pte_mkyoung(); if (is_write)
pte_mkdirty();
In fact, if the PTE is not marked young/dirty, our dirty/accessed bit
emulation would cause the TLB permission not to be changed, and so we'd loop,
and given we don't support preemption yet, we'd busy-hang here.
However, I've seen this warning trigger without crashes during a loop of
concurrent kernel builds, at random times (i.e. like a race condition), and I
realized that two concurrent faults on the same page, one on read and one on
write, can trigger it. The read fault gets serviced and the PTE gets marked
writable but clean (it's possible on a shared-writable mapping), while the
generic code sees the PTE was already installed and returns without action. In
this case, we'll see another fault and service it normally.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In Uml, many definitions are borrowed from underlying subarch headers (with
#include <asm/arch/stuff.h>). And it has become annoying to keep switching
tag files all time, so by default index the underlying subarch headers too.
Btw, it adds negligible space to the tags file (less than 1M surely, IIRC it
was around 500k over 40M).
Finally, preserve the ALLSOURCE_ARCHS command line option (I hope) - if it is
set, it is used for headers too as before. But check my construct please, I
didn't test this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove task_work structure, use the standard thread flags functions and use
shifts in entry.S to test the thread flags. Add a few local labels to entry.S
to allow gas to generate short jumps.
Finally it changes a number of inline functions in thread_info.h to macros to
delay the current_thread_info() usage, which requires on m68k a structure
(task_struct) not yet defined at this point.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a) added embedded thread_info [m68k processor.h]
b) added missing symbols in asm-offsets.c
c) task_thread_info() and friends in asm-m68k/thread_info.h
d) made m68k thread_info.h included by m68k processor.h, not the other way
round.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a) in smp_lock.h #include of sched.h and spinlock.h moved under #ifdef
CONFIG_LOCK_KERNEL.
b) interrupt.h now explicitly pulls sched.h (not via smp_lock.h from
hardirq.h as it used to)
c) in three more places we need changes to compensate for (a) - one place
in arch/sparc needs string.h now, hardirq.h needs forward declaration of
task_struct and preempt.h needs direct include of thread_info.h.
d) thread_info-related helpers in sched.h and thread_info.h put under
ifndef __HAVE_THREAD_FUNCTIONS. Obviously safe.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
encapsulates the rest of arch-dependent operations with thread_info access.
Two new helpers - setup_thread_stack() and end_of_stack(). For normal case
the former consists of copying thread_info of parent to new thread_info and
the latter returns pointer immediately past the end of thread_info.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
new helper - task_thread_info(task). On platforms that have thread_info
allocated separately (i.e. in default case) it simply returns
task->thread_info. m68k wants (and for good reasons) to embed its thread_info
into task_struct. So it will (in later patch) have task_thread_info() of its
own. For now we just add a macro for generic case and convert existing
instances of its body in core kernel to uses of new macro. Obviously safe -
all normal architectures get the same preprocessor output they used to get.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=5546
The cpu_khz global is not initialized and remains 0 if you boot with
clock=pit, even if the processor does have a TSC. This may have bad
ramifications since the variable is used in various places scattered around
the kernel, though I didn't check them all to see if they can tolerate cpu_khz
= 0. You can observe the problem by doing "cat /proc/cpuinfo"; the cpu MHz
line says 0.000.
The fix is trivial; call init_cpu_khz() from init_pit(), just as it's called
from the timers/timer_foo.c:init_foo() for other values of foo.
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following cleanups:
- make a needlessly global function static
- every file should include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/powerpc/xmon/xmon.c:525: error: syntax error before "xmon_irq"
arch/powerpc/xmon/xmon.c:526: warning: return type defaults to `int'
arch/powerpc/xmon/xmon.c: In function `xmon_irq':
arch/powerpc/xmon/xmon.c:532: error: `IRQ_HANDLED' undeclared (first use in this function)
arch/powerpc/xmon/xmon.c:532: error: (Each undeclared identifier is reported only once
arch/powerpc/xmon/xmon.c:532: error: for each function it appears in.)
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The MPC8349 PIBs system has a expansion board with 6 PCI slots. We needed
to update the IDSEL interrupt mapping for it to work properly. However,
only PCI1 is supported as the first revision of this expansion board
doesn't function properly for PCI2. For the time being we have zero'd out
the entries for the IDSELs related to PCI2. When a functioning expansion
board exists we can fix the table.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The slab allocator never uses alloc_pages since kmem_getpages() is always
called with a valid nodeid. Remove the branch and the code from
kmem_getpages()
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts object cache <-> page mapping macros to static inline
functions to make the more explicit and readable.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pages_high - pages_low and pages_low - pages_min deltas are the asynch
reclaim watermarks. As such, the should be in the same ratios as any other
zone for highmem zones. It is the pages_min - 0 delta which is the
PF_MEMALLOC reserve, and this is the region that isn't very useful for
highmem.
This patch ensures highmem systems have similar characteristics as non highmem
ones with the same amount of memory, and also that highmem zones get similar
reclaim pressures to other zones.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove last remnant of the defunct early reclaim page logic, the no longer
used __GFP_NORECLAIM flag bit.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Martin Hicks <mort@bork.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up of __alloc_pages.
Restoration of previous behaviour, plus further cleanups by introducing an
'alloc_flags', removing the last of should_reclaim_zone.
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The address based work estimate for unmapping (for lockbreak) is and always
was horribly inefficient for sparse mappings. The problem is most simply
explained with an example:
If we find a pgd is clear, we still have to call into unmap_page_range
PGDIR_SIZE / ZAP_BLOCK_SIZE times, each time checking the clear pgd, in
order to progress the working address to the next pgd.
The fundamental way to solve the problem is to keep track of the end
address we've processed and pass it back to the higher layers.
From: Nick Piggin <npiggin@suse.de>
Modification to completely get away from address based work estimate
and instead use an abstract count, with a very small cost for empty
entries as opposed to present pages.
On 2.6.14-git2, ppc64, and CONFIG_PREEMPT=y, mapping and unmapping 1TB
of virtual address space takes 1.69s; with the following patch applied,
this operation can be done 1000 times in less than 0.01s
From: Andrew Morton <akpm@osdl.org>
With CONFIG_HUTETLB_PAGE=n:
mm/memory.c: In function `unmap_vmas':
mm/memory.c:779: warning: division by zero
Due to
zap_work -= (end - start) /
(HPAGE_SIZE / PAGE_SIZE);
So make the dummy HPAGE_SIZE non-zero
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In __alloc_pages():
if ((p->flags & (PF_MEMALLOC | PF_MEMDIE)) && !in_interrupt()) {
/* go through the zonelist yet again, ignoring mins */
for (i = 0; zones[i] != NULL; i++) {
struct zone *z = zones[i];
page = buffered_rmqueue(z, order, gfp_mask);
if (page) {
zone_statistics(zonelist, z);
goto got_pg;
}
}
goto nopage; <<<< HERE!!! FAIL...
}
kswapd (which has PF_MEMALLOC flag) can fail to allocate memory even when
it allocates it with __GFP_NOFAIL flag.
Signed-Off-By: Pavel Emelianov <xemul@sw.ru>
Signed-Off-By: Denis Lunev <den@sw.ru>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/pci/hotplug/pciehp_hpc.c:221: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:221: warning: type defaults to `int' in declaration of `pcie_isr'
drivers/pci/hotplug/pciehp_hpc.c:221: warning: data definition has no type or storage class
drivers/pci/hotplug/pciehp_hpc.c: In function `hpc_release_ctlr':
drivers/pci/hotplug/pciehp_hpc.c:715: implicit declaration of function `free_irq'
drivers/pci/hotplug/pciehp_hpc.c: At top level:
drivers/pci/hotplug/pciehp_hpc.c:839: parse error before "pcie_isr"
drivers/pci/hotplug/pciehp_hpc.c:840: warning: return type defaults to `int'
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_isr':
drivers/pci/hotplug/pciehp_hpc.c:850: `IRQ_NONE' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c:850: (Each undeclared identifier is reported only once
drivers/pci/hotplug/pciehp_hpc.c:850: for each function it appears in.)
drivers/pci/hotplug/pciehp_hpc.c:979: `IRQ_HANDLED' undeclared (first use in this function)
drivers/pci/hotplug/pciehp_hpc.c: In function `pcie_init':
drivers/pci/hotplug/pciehp_hpc.c:1362: implicit declaration of function `request_irq'
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an error in w100fb after the platform device conversion.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is an old bug in the pkt_count_states() function that causes stack
corruption. When compiling with gcc 3.x or 2.x it is harmless, but gcc 4
allocates local variables differently, which makes the bug visible.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is wrong to acquire the semaphore and then return from
cpuset_zone_allowed without releasing it.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nvidiafb_pan_display() is incorrectly using the fields in info->var instead
of var passed to the function.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: _machine is some ppc64 thing - this is a powerpc-only driver)
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When ptrace_attach fails we need to drop the task_struct reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Exporting struct fb_display produces this warning error on depmod:
WARNING: Module
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/fbcon_ud.ko
ignored, due to loop
WARNING: Module
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/fbcon_rotate.ko
ignored, due to loop
WARNING: Module
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/fbcon_cw.ko
ignored, due to loop
WARNING: Module
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/fbcon_ccw.ko
ignored, due to loop
WARNING: Module
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/fbcon.ko ignored,
due to loop
WARNING: Loop detected:
/lib/modules/2.6.14-mm2/kernel/drivers/video/console/bitblit.ko needs
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/video/nvidia/nv_of.c:33: error: redefinition of `nvidia_probe_of_connector'
drivers/video/nvidia/nv_proto.h:51: error: `nvidia_probe_of_connector' previously defined here
Because the inline version depends on !CONFIG_FB_OF and the out-of-line
version depends on CONFIG_PPC_OF.
Ben said: "Yes, CONFIG_PPC_OF is the right one, must be a typo."
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
C: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The file_lock spinlock sits close to mostly read fields of 'struct
files_struct'
In SMP (and NUMA) environments, each time a thread wants to open or close
a file, it has to acquire the spinlock, thus invalidating the cache line
containing this spinlock on other CPUS. So other threads doing
read()/write()/... calls that use RCU to access the file table are going
to ask further memory (possibly NUMA) transactions to read again this
memory line.
Move the spinlock to another cache line, so that concurrent threads can
share the cache line containing 'count' and 'fdt' fields.
It's worth up to 9% on a microbenchmark using a 4-thread 2-package x86
machine. See
http://marc.theaimsgroup.com/?l=linux-kernel&m=112680448713342&w=2
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
attached patch renames one instance of
/sys/devices/system/timer
to
/sys/devices/system/timer_pit
to avoid a name clash with another instance created in time.c.
Acked-by: Andi Kleen <ak@muc.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_ELAN doesn't exist any more; CONFIG_X86_ELAN is too specific
so make ts-5500 memory map dependant on CONFIG_X86.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The patch
http://linux.bkbits.net:8080/linux-2.6/diffs/fs/locks.c@1.70??nav=index.html
introduced a pretty nasty memory leak in the lease code. When freeing
the lease, the code in locks_delete_lock() will correctly clean up
the fasync queue, but when we return to fcntl_setlease(), the freed
fasync entry will be reinstated.
This patch ensures that we skip the call to fasync_helper() when we're
freeing up the lease.
Signed-off-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
sil24_port_stop() is missing call to ata_pad_free() thus leaking pad
buffer when a port is stopped. This patch adds it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If we fail to re-startup a serial port on resume, shut it down
immediately and mark it as an error condition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a driver for the extra GPIOs found on the Sharp SL-C1000 (Akita).
These GPIOs are found on a Maxim MAX7310 I2C i/o expander chip. A
generic GPIO driver for the MAX7310 was attempted but this mini
driver is a much simpler and much more effective solution avoiding
several issues and complexity the generic driver had (as discussed
on LKML).
The platform device is required so the device parent can be set
correctly which ensures the device is one of the last to suspend
and first to resume. Whilst the i2c suspend/resume calls can be
influenced, nothing guarantees this is easlier/later than the
subsystems the gpios are used on which are all independent of i2c
(sound, irda, video/backlight etc.).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-Cxx00 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-C7x0 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Print out minimal information in dmesg whnever a CardBus or PCMCIA card
is inserted into or ejected from a slot. This will make debugging certain
types of bugs much easier, and is similar to output produced by other
hotpluggable buses.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Claim the WACF005 device. This is the pen display pointing device on
the HP Compaq tc1100 Tablet PC. More information about using this
device, including using it as an X pointer device:
http://www.theory.bham.ac.uk/staff/schofield/linux/tc1100/
Christopher Kemp <ck231@cam.ac.uk> did the legwork of determining that
the WACF005 is really just a plain old UART and doing an initial ACPI
driver (before we had PNPACPI), and David Ludlow <dave@adsllc.com>
confirmed that PNPACPI + the attached patch is now sufficient:
pnp: Device 00:05 activated.
ttyS4 at I/O 0x300 (irq = 4) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
xscale-type UARTs have an extra bit (UUE) in the IER register that has
to be written as 1 to enable the UART. At the end of autoconfig() in
drivers/serial/8250.c, the IER register is unconditionally written as
zero, which turns off the UART, and makes any subsequent printch() hang
the box.
Since other 8250-type UARTs don't have this enable bit and are thus
always 'enabled' in this sense, it can't hurt to enable xscale-type
serial ports all the time as well. The attached patch changes the
autoconfig() exit path to see if the port has an UUE enable bit, and if
yes, to write UUE=1 instead of just putting a zero into IER, using the
same test as is used at the beginning of serial8250_console_write().
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the new platform_device helpers in the i82365 driver to get rid of the
"device 'i823650' does not have a release() function" warning, and to solve
bug #3676.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This fixes compilation for collie after -rc1 platform_device
changes. And yes, it even boots.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some devices (e.g. Qlogic iSCSI HBA hardware like QLA4010 up to firmware
3.0.0.4) initiates TCP with SYN and PUSH flags set.
The Linux TCP/IP stack deals fine with that, but the connection tracking
code doesn't.
This patch alters TCP connection tracking to accept SYN+PUSH as a valid
flag combination.
Signed-off-by: Vlad Drukker <vlad@storewiz.com>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent change to netlink dump "done" callback handling broke IPv6
which played dirty tricks with the "done" callback. This causes an
infinite loop during a dump.
The following patch fixes it.
This bug was reported by Jeff Garzik.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new function, sbusfb_compat_ioctl() to
drivers/video/sbuslib.c and uses it as compat_ioctl in all sbus fb
drivers
This remove the last per-arch compat ioctl bits in
arch/sparc64/kernel/ioctl32.c so it would be nice if people could test
if this actually copiles and works and if yes apply it :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Fri, Nov 11, 2005 at 12:58:40PM -0800, David S. Miller wrote:
>
> This change:
>
> diff-tree 8ca2bdc7a9 (from feee207e44d3643d19e648aAuthor: Christoph Hellwig <hch@lst.de>
> Date: Wed Nov 9 12:07:18 2005 -0800
>
> [SPARC] sbus rtc: implement ->compat_ioctl
>
> Signed-off-by: Christoph Hellwig <hch@lst.de>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
> results in the console now getting spewed on sparc64 systems
> with messages like:
>
> [ 11.968298] ioctl32(hwclock:464): Unknown cmd fd(3) cmd(401c7014){00} arg(efc
> What's happening is hwclock tries first the SBUS rtc device ioctls
> then the normal rtc driver ones.
>
> So things actually worked better when we had the SBUS rtc compat ioctl
> directly handled via the generic compat ioctl code.
>
> There are _so_ many rtc drivers in the kernel implementing the
> generic rtc ioctls that I don't think putting a ->compat_ioctl
> into all of them to fix this problem is feasible. Unless we
> write a single rtc_compat_ioctl(), export it to modules, and hook
> it into all of those somehow.
>
> But even that doesn't appear to have any pretty implementation.
>
> Any better ideas?
We had similar problems with other ioctls where userspace did things
like that. What we did there was to put the compat handler to generic
code. The patch below does that, adding a big comment about what's
going on and removing the COMPAT_IOCTL entires for these on powerpc
that not only weren't ever useful but are duplicated now aswell.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make /proc/i8k display '?' when service tag is blank in BIOS.
This fixes segfault in i8k gkrellm plugin.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Updates to the SharpSL PM driver including cleanups from both
Pavel Machek and myself and updates after the platform device
changes to make it compile again.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add the core machine support for the Sharp SL-C1000 (Akita)
and enable the Kconfig selection for it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes
drivers/built-in.o: In function `flexcop_frontend_init':
: undefined reference to `lgdt330x_attach'
[ Side note: I really dislike that dvb people want to include every
possible frontend into the kernel - I only need the mt312 one for my
Skystar2 card. I'd highly appreciate it this would be made selectable
again... ]
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must _never_ _ever_ on pain of death enable IDE DMA on SL82C105
chipsets where the southbridge revision is <= 5, otherwise data
corruption will occur.
Strangely this used to work, but something has changed in the upper
echelons of the IDE layer to break the hosts decision to deny DMA.
Let's make it crystal clear to the IDE layer that we know best.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With generic dispatch queue update, implicit former/latter request
handling using rq->queuelist.prev/next doesn't work as expected
anymore. Also, the only iosched dependent on this feature was
noop-iosched and it has been reimplemented to have its own
latter/former methods. This patch removes implicit former/latter
handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
The original implementation directly used dispatch queue. As new
generic dispatch queue imposes stricter rules over ioscheds and
dispatch queue usage, this direct use becomes somewhat problematic.
This patch reimplements noop-iosched such that it complies to generic
iosched model better. Request merging with q->last_merge and
rq->queuelist.prev/next work again now.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de
When cfq slice expires, remainder of slice is calculated and stored in
cfqq->slice_left. Current code calculates the opposite of remainder -
how many jiffies the cfqq has used past slice end. This patch fixes
the bug.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
elv_iosched_store doesn't terminate string passed from userspace if
it's too long. Also, if the written length is zero (probably not
possible), it accesses elevator_name[-1]. This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch adds request_queue->nr_sorted which keeps the number of
requests in the iosched and implement elv_drain_elevator which
performs forced dispatching. elv_drain_elevator checks whether
iosched actually dispatches all requests it has and prints error
message if it doesn't. As buggy forced dispatching can result in
wrong barrier operations, I think this extra check is worthwhile.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
cfq forced dispatching might not return all requests on the queue.
This bug can hang elevator switchinig and corrupt request ordering
during flush sequence.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
In addition to the first patch, which is probably goodness, I found the
cause of my panic - applying this patch fixes it and now I am booting.
If the chosen_elevator[] is not found, fall back to noop.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
I got a panic in the elevator code, backtrace :
Unable to handle kernel NULL pointer dereference at virtual address 00000060
..
EIP is at elevator_put+0x0/0x30 (null elevator_type passed)
..
elevator_init+0x38
blk_init_queu_node+0xc9
floppy_init+0xdb
do_initcalls+0x23
init+0x10a
init+0x0
Clearly if the kmalloc here fails, e->elevator_type is not yet set; this
appears to be the correct fix, but I think I probably hit the second case
due to a race condition. Someone more familiar with the elevator code
should look at this more closely until I can determine if I can reproduce.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Although according to the documentation this largely only affects
desktop LED control, let's make sure we set the ATAPI bit when we
have an ATAPI device attached to the port.
Also introduces a sysctl option to configure the receive buffer
accounting policy to be either at socket or association level.
Default is all the associations on the same socket share the
receive buffer.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ia64, it is possible to get NaT Consumption Fault and a kernel panic
when initializing sctp sideeffect commands arguments. The union
sctp_arg_t contains different sized elements and when loading a smaller
sized element (32 or 16 bits), it is possible for a speculative load to
fail and result in a NaT bit set which causes a kernel crash. The easy
way to get around it is to load the largerst member of the union.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket level timeout values are maintained in sctp_sock and
association level timeouts are in sctp_association. So there is
no need for ep->timeouts.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to get to sctp_v4_get_saddr() without a valid
association. This happens when processing OOTB packets and
the cached route entry is no longer valid.
However, when responding to OOTB packets we already properly
set the source address based on the information in the OOTB
packet. So, if we we get to sctp_v4_get_saddr() without an
association we can simply return.
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based mostly upon a patch from Olaf Kirch <okir@suse.de>
When initialization fails in inet6_init(), we should
unregister the PF_INET6 socket ops.
Also, check sock_register()'s return value for errors.
Signed-off-by: David S. Miller <davem@davemloft.net>
scsi_wait_req does not exist any more in the SCSI layer. This patch
makes it so libata can compile again.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After the last merge of the new unified 'powerpc' architecture, ppc64 no
longer compiles cleanly as a standalone architecture. Some bits and
pieces still exist as files under the old ppc64 hierarchy, but the old
"ARCH=ppc64" is dead.
So if "uname" says ppc64, that now implies that the default architecture
should be "powerpc".
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increase SRP max_luns to 512 to match the kernel's default, since SRP
storage targets can have lots of LUNs and the SRP initiator itself
doesn't have any particular limit.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Patch from Nicolas Pitre
For assembly labels to actually be local they must start with ".L" and
not only "." otherwise they still remain visible in the final link and
clutter kallsyms needlessly, and possibly make for unclear symbolic
backtrace. This patch simply inserts a"L" where appropriate. The code
itself is unchanged.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
For assembly labels to actually be local they must start with ".L" and
not only "." otherwise they still remain visible in the final link and
clutter kallsyms needlessly, and possibly make for unclear symbolic
backtrace. This patch simply inserts a"L" where appropriate. The code
itself is unchanged.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
For assembly labels to actually be local they must start with ".L" and
not only "." otherwise they still remain visible in the final link and
clutter kallsyms needlessly, and possibly make for unclear symbolic
backtrace. This patch simply inserts a"L" where appropriate. The code
itself is unchanged.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Noticed by Tom 'spot' Callaway.
Even on uniprocessor we always reported the number of physical
cpus in the system via /proc/cpuinfo. But when this got changed
to use num_possible_cpus() it always reads as "1" on uniprocessor.
This change was unintentional.
So scan the firmware device tree and count the number of cpu
nodes, and report that, as we always did.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently recvmsg generates SIGPIPE whereas sendmsg does not; for the
other stacks it seems to be the other way round!
It also fixes the bug where reading from a socket whose peer has shutdown
returned -EINVAL rather than 0.
Signed-off-by: Patrick Caulfield <patrick@tykepenguin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix default VGA console on SN platforms. Since SN firmware does not pass
enough ACPI information to identify VGA cards and the associated legacy IO/MEM
addresses, we rely on the EFI PCDP table. Since the linux pcdp driver is
optional (and overridden if console= directives are used) SN duplicates a
portion of the pcdp scan code to identify if there is a usable console VGA
adapter. Additionally, dup necessary pcdp related structs to avoid dragging
drivers/pcdp.h into a more public location.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch introduces 4-level page tables to ia64. I have run
some benchmarks and found nothing interesting. Performance has
consistently fallen within the noise range.
It also introduces a config option (setting the default to 3
levels). The config option prevents having 4 level page
tables with 64k base page size.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Part of a patch was accidentally reverted, this corrects an
inconsistent spinlock use in the IPMI message handler.
Signed-off-by: Hironobu Ishii <hishii@soft.fujitsu.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As part of the ISO C9x conversion gcc deprecates concatenation with
__FUNCTION__ because __FUNCTION__ is not a preprocessor macro.
Signed-off-by: Clemens Buchacher <drizzd@aon.at>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch support the SMC9111 present on DB1200 boards.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
o Try to work around some of the undocumented "features" of the SAA9730
o Use netdev_priv() instead of the previous broken mechanism to allocate
the private data structure.
o Try to make sure we don't leak resources on exit.
o No more need to call SET_MODULE_OWNER in 2.6.
o Use pci_free_consistent instead of homegrown architecture-specific
allocation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/saa9730.c | 531 +++++++++++++++++++++++---------------------------
1 files changed, 249 insertions(+), 282 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains support for different modes of interrupt mitigation
of forcedeth. It includes changes based on Jeff's comments. Currently,
the modes are changed through module parameters since ethtool does not
support something similar.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
To ensure that phy_mask and any future elements of the mii_bus
structure are initialized use kzalloc() instead of kmalloc().
This fixes an issue in which phy_mask was not being initialized
and we would skip random phy addresses when scanning.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 6/7] s390: introduce guestLan sniffer support in qeth
From: Peter Tiedemann <ptiedem@de.ibm.com>
- introduce guestLan sniffer support in qeth
feature allows a linux in a virtual machine
guest to become a network LAN sniffer,
monitoring and recording the networking traffic
within an entire guestLan.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 2 +
qeth_main.c | 93 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
qeth_mpc.h | 11 ++++---
3 files changed, 102 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 5/7] s390: fix recovery failure of non-guestLAN devices
From: Frank Pavlic <fpavlic@de.ibm.com>
- Recovery of non-guestLAN Layer 2 device failed due to
trying to register the real MAC address we got from
the READ_MAC adapter parameters command.
We have to keep the "old" MAC address when we process
the reply of a READ_MAC.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth.h | 12 ++++++------
qeth_main.c | 27 ++++++++++++++++-----------
2 files changed, 22 insertions(+), 17 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 4/7] s390: some more qeth fixes
From: Frank Pavlic <fpavlic@de.ibm.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
- possible race on list fixed by reset
list processing after every operation
- traffic hang fixed
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 11 +++++++----
1 files changed, 7 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 3/7] s390: qeth multicast address registration fixed
From: Klaus Dieter Wacker <kdwacker@de.ibm.com>
- when running in Layer2 mode we don't have to register
the multicast IP address but only group mac address.
Therefore for Layer 2 devices it is enough to go
through dev->mc_list list and register these entries.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 106 +++++++++++++++++++++++++++++++++++++++++++++---------------
1 files changed, 80 insertions(+), 26 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[patch 2/7] s390: minor modification in qeth layer2 code
From: Frank Pavlic <fpavlic@de.ibm.com>
- use qeth_layer2_send_setdelvlan_cb to check
return code of a SET/DELVLAN IP Assist command.
It fits better in qeth's design and mechanism of IP Assist
command handling.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
diffstat:
qeth_main.c | 40 ++++++++++++++++++++++++++--------------
1 files changed, 26 insertions(+), 14 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This will let me chop the code size of several drivers right down. In
many cases the actual private data is very useful and constant for a
given host controller so being able to just pass it at probe time would
be very useful indeed (eg with the via driver would could pass the udma
clocking and reduce the code size, or with the AMD one the UDMA
multiplier and the offset)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* Merge PCMCIA card table with new Brodowski PCMCIA id table.
* Add missing entries to PCMCIA id table.
* Other tweaks to conform with Documentation/driver-changes.txt
(types, call request_region, etc)
* Fix size of requested IO region.
* Reduce printk verbosity.
* Remove EXPERIMENTAL
* tweak to association code - don't force shared key authentication
when wep in use.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we created the instructions to read/write SPRs in xmon, we were
setting up a ppc64-style procedure descriptor and calling that, which
doesn't work in 32-bit. For 32-bit a function pointer just points
to the instructions of the function. This fixes it to do the right
thing for both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit SMP powermacs weren't booting with ARCH=powerpc because the
boot cpu wasn't saving away the state of various control registers,
but the secondary CPUs were loading them from the uninitialized
state. This adds the necessary save-state call.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the vdso's to arch/powerpc, adds support for the 32
bits vdso to the 32 bits kernel, rename systemcfg (finally !), and adds
some new (still untested) routines to both vdso's: clock_gettime() with
support for CLOCK_REALTIME and CLOCK_MONOTONIC, clock_getres() (same
clocks) and get_tbfreq() for glibc to retreive the timebase frequency.
Tom,Steve: The implementation of get_tbfreq() I've done for 32 bits
returns a long long (r3, r4) not a long. This is such that if we ever
add support for >4Ghz timebases on ppc32, the userland interface won't
have to change.
I have tested gettimeofday() using some glibc patches in both ppc32 and
ppc64 kernels using 32 bits userland (I haven't had a chance to test a
64 bits userland yet, but the implementation didn't change and was
tested earlier). I haven't tested yet the new functions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes a stray debugging printk which offended Anton.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the udbg code in ppc64 has no ppc32 equivalent, move it straight
over into arch/powerpc (and include/asm-powerpc for udbg.h). In time,
we probably want to meld the various bits and pieces of 32-bit early
debugging code into udbg, but for now only include it on
CONFIG_PPC64=y builds. The only change during the move is to
standardise the protecting #ifdef/#define in udbg.h, and move its
banner comment above the initial #ifdef (which seems to be normal
practice).
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built
for 32bit multiplatform (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The definitions in sparsemem.h arent sufficient. We currently sell
machines with 2TB of RAM, and in order to give us room for a few years
growth lets set it to 16TB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert to sparsemem and remove all the discontigmem code in the
process. This has a few advantages:
- The old numa_memory_lookup_table can go away
- All the arch specific discontigmem magic can go away
We also remove the triple pass of memory properties and instead create a
list of per node extents that we iterate through. A final cleanup would
be to change our lmb code to store extents per node, then we can reuse
that information in the numa code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove ppc64 specific version of nr_cpus_node and use the generic one
provided.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove an unused numa define and move a discontigmem specific define
inside the relevant ifdef.
I will submit a separate patch to remove them from other architectures,
but the ppc64 patches to follow depend on this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kprobes code is doing ".previous .text". While the assembler doesnt
warn at the moment (and it seems to work), it might in the future.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have been printing the raw ppc64_firmware_features during boot. Since
we can work it out from the device tree, lets remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we dont have permission to read some information from the hypervisor,
lparcfg outputs a warning on the console. Now that lparcfg is world
readable this is a problem.
Dont warn in the case of H_Authority, remove some unnecessary function
prototypes and fix whitespace damage in a structure as well.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bit position in the status register corresponding to the
PCI DMA interrupt was incorrect. Additionally, we did not
have a define for the PCI DMA interrupt.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Alpha:
include/linux/libata.h: In function `ata_pad_alloc':
include/linux/libata.h:785: warning: implicit declaration of function `dma_alloc_coherent'
include/linux/libata.h:786: warning: assignment makes pointer from integer without a cast
include/linux/libata.h: In function `ata_pad_free':
include/linux/libata.h:792: warning: implicit declaration of function `dma_free_coherent'
(I have a decouple-some-header-files cleanup in -mm, so it's causing some
fallout of this nature)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
At the moment ibmveth has DEBUG enabled which is rather verbose. Disable
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Current upstream 'allmodconfig' build is broken. This is the obvious
patch...
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use "hints" to speed up the SACK processing. Various forms
of this have been used by TCP developers (Web100, STCP, BIC)
to avoid the 2x linear search of outstanding segments.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch for discussion addressing some receive buffer growing issues.
This is partially related to the thread "Possible BUG in IPv4 TCP window
handling..." last week.
Specifically it addresses the problem of an interaction between rcvbuf
moderation (receiver autotuning) and rcv_ssthresh. The problem occurs when
sending small packets to a receiver with a larger MTU. (A very common case I
have is a host with a 1500 byte MTU sending to a host with a 9k MTU.) In
such a case, the rcv_ssthresh code is targeting a window size corresponding
to filling up the current rcvbuf, not taking into account that the new rcvbuf
moderation may increase the rcvbuf size.
One hunk makes rcv_ssthresh use tcp_rmem[2] as the size target rather than
rcvbuf. The other changes the behavior when it overflows its memory bounds
with in-order data so that it tries to grow rcvbuf (the same as with
out-of-order data).
These changes should help my problem of mixed MTUs, and should also help the
case from last week's thread I think. (In both cases though you still need
tcp_rmem[2] to be set much larger than the TCP window.) One question is if
this is too aggressive at trying to increase rcvbuf if it's under memory
stress.
Orignally-from: John Heffner <jheffner@psc.edu>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an updated version of the RFC3465 ABC patch originally
for Linux 2.6.11-rc4 by Yee-Ting Li. ABC is a way of counting
bytes ack'd rather than packets when updating congestion control.
The orignal ABC described in the RFC applied to a Reno style
algorithm. For advanced congestion control there is little
change after leaving slow start.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the code that does linear TCP slowstart to one
inline function to ease later patch to add ABC support.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code that comuputes microsecond rtt estimate used
by TCP Vegas. Move the callback out of the RTT sampler and into
the end of the ack cleanup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP peformance with TSO over networks with delay is awful.
On a 100Mbit link with 150ms delay, we get 4Mbits/sec with TSO and
50Mbits/sec without TSO.
The problem is with TSO, we intentionally do not keep the maximum
number of packets in flight to fill the window, we hold out to until
we can send a MSS chunk. But, we also don't update the congestion window
unless we have filled, as per RFC2861.
This patch replaces the check for the congestion window being full
with something smarter that accounts for TSO.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After much testing and agony, I've discovered that my previous ohci1394
quirk for Toshiba laptops is not 100% reliable. It apparently fails to
do the interrupt line change either correctly or in time, since in about
2 out of 5 boots, the kernel's irqdebug code will *still* disable irq 11
when the ohci1394 driver is loaded (at pci_enable_device time I think).
This patch switches things around a little in the workaround. First, it
removes the mdelay. I didn't see a need for it and my testing has shown
that it's not necessary for the quirk to work.
Secondly, instead of trying to change the interrupt line to what ACPI
tells us it should be, this patch makes the quirk use the value in the
PCI_INTERRUPT_LINE register. On this laptop at least, that seems to be
the right thing to do, though additional testing on other laptops and/or
with actual firewire devices would be appreciated.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI hardcoded delivery mode to use logical delivery mode. Recently
x86_64 moved to use physical mode addressing to support physflat mode.
With this mode enabled noticed that my eth with MSI werent working.
msi_address_init() was hardcoded to use logical mode for i386 and x86_64.
So when we switch to use physical mode, things stopped working.
Since anyway we dont use lowest priority delivery with MSI, its always
directed to just a single CPU. Its safe and simpler to use
physical mode always, even when we use logical delivery mode for IPI's
or other ioapic RTE's.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- access.c should #include "pci.h" for getting the prototypes of it's
global functions
- hotplug/shpchp_pci.c: make the needlessly global function
program_fw_provided_values() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_ids cleanup: fixup bt87x.c: two macro defined IDs missed in prior cleanup.
Caught by Chun-Chung Chen <cjj@u.washington.edu>: "In the patch for bt87x.c,
you seemed have missed the two occurrences of BT_DEVICE on line 897 and
line 898."
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the driver bits for enabling DLPAR and PCI Hotplug
for the new OF-based PCI probe. This functionality was regressed when
the new PCI approach was introduced. Please apply if appropriate.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A nice feature of sysfs is that it can create the symlink from the
driver to the module that is contained in it.
It requires that the device_driver.owner is set, what is not the
case for many PCI drivers.
This patch allows pci_register_driver to set automatically the
device_driver.owner for any PCI driver.
Credits to Al Viro who suggested the method.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
drivers/ide/setup-pci.c | 12 +++++++-----
drivers/pci/pci-driver.c | 9 +++++----
include/linux/ide.h | 3 ++-
include/linux/pci.h | 10 ++++++++--
4 files changed, 22 insertions(+), 12 deletions(-)
store_new_id() should not be (and cannot be) inline;
the function pointer is stored in a device_attribute table.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the PPC fixup for old NCR 810 controllers to generic quirks -
it's needed for Alpha, x86 and other architectures that use
setup-bus.c.
Thanks to Jay Estabrook for pointing out the issue.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The quirk names for VIA 686 are mistyped in 2.6.14 (686 vs 868). S3 868
influence? :) Here is a patch to correct them.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pciehp implementation reports a power-fail error
even if the condition has cleared by the time the corresponding
interrupt handling code gets a chance to run. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch further tweaks how we request control of hotplug
controller hardware from BIOS. We first search the ACPI namespace
corresponding to a specific hotplug controller looking for an
_OSC or OSHP method. On failure, we successively move to the
ACPI parent object, till we hit the highest level host bridge
in the hierarchy. This allows for different types of BIOS's
which place the _OSC/OSHP methods at various places in the acpi
namespace, while still not encroaching on the namespace of
some other root level host bridge.
This patch also introduces a new load time option (pciehp_force)
that allows us to bypass all _OSC/OSHP checking. Not supporting
these methods seems to be be the most common ACPI firmware problem
we've run into. This will still _not_ allow the pciehp driver to
work correctly if the BIOS really doesn't support pciehp (i.e. if
it doesn't generate a hotplug interrupt). Use this option with
caution. Some BIOS's may deliberately not build any _OSC/OSHP
methods to make sure it retains control the hotplug hardware.
Using the pciehp_force parameter for such systems can lead to
two separate entities trying to control the same hardware.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tweaks the way pciehp requests control of the hotplug
hardware from BIOS. It now tries to invoke the ACPI _OSC method
for a specific hotplug controller only, rather than walking the
entire acpi namespace invoking all possible _OSC methods under
all host bridges. This allows us to gain control of each hotplug
controller individually, even if BIOS fails to give us control of
some other hotplug controller in the system.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if pciehp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in pciehp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the PCI Express hotplug driver's dependence on ACPI.
We don't walk the acpi namespace anymore to build a list of
bridges and devices. We go to ACPI only to run the _OSC or
_OSHP methods to transition control of hotplug hardware from
system BIOS to the hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that pciehp
does not automatically enable the hot-added device or its DMA
bus mastering capability now. It expects the device driver to
do that. This may break some drivers and we will have to fix
them as they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the pci express hotplug controller driver
to use the PCI core for resource management. This eliminates a
lot of duplicated code and integrates pciehp with the system's
normal PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have more than one capability of the same type. For
example, the PCI header for the PathScale InfiniPath looks like:
04:01.0 InfiniBand: Unknown device 1fc1:000d (rev 02)
Subsystem: Unknown device 1fc1:000d
Flags: bus master, fast devsel, latency 0, IRQ 193
Memory at fea00000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Capabilities: [f8] HyperTransport: Interrupt Discovery and Configuration
There are _two_ HyperTransport capabilities, and the PathScale driver
wants to look at both of them.
The current pci_find_capability() API doesn't work for this, since it
only allows us to get to the first capability of a given type. The
patch below introduces a new pci_find_next_capability(), which can be
used in a loop like
for (pos = pci_find_capability(pdev, <ID>);
pos;
pos = pci_find_next_capability(pdev, pos, <ID>)) {
/* ... */
}
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I just hit a page allocation error on a kernel configured to support
64 CPUs. It spewed 60 completely useless unnecessary lines of info.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a first go at some documentation. Please advise if gmail
has mangled patch and I will revert to an attachment:
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol field in ethernet headers is big-endian and should be
annotated as such. This patch allows detection of missing ntohs() calls
on the ethernet protocol field when sparse is run with __CHECK_ENDIAN__
defined.
This is a revised version that includes <linux/types.h> so that the
userspace programs are not confused by __be16. Thanks to David S.
Miller.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the patch that introduces the generic skb_checksum_complete
which also checks for hardware RX checksum faults. If that happens,
it'll call netdev_rx_csum_fault which currently prints out a stack
trace with the device name. In future it can turn off RX checksum.
I've converted every spot under net/ that does RX checksum checks to
use skb_checksum_complete or __skb_checksum_complete with the
exceptions of:
* Those places where checksums are done bit by bit. These will call
netdev_rx_csum_fault directly.
* The following have not been completely checked/converted:
ipmr
ip_vs
netfilter
dccp
This patch is based on patches and suggestions from Stephen Hemminger
and David S. Miller.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the superfluous parameter checking in bnx2_{get,set}_eeprom.
The parameters are already validated in ethtool_{get,set}_eeprom.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of dev_alloc_skb in bnx2_test_loopback, and handle
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output driver name as prefix to "Unknown flash/EEPROM type." message.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have to revert the recent addition of -imacros to the Makefile to get my
tool chain to build. Without the change, below, I get:
Note that this looks entirely like a toolchain bug. Here is the offending command:
[pid 12163] execve("/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0", ["/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0", "-lang-asm", "-nostdinc", "-Iinclude", "-Iinclude/asm-i386/mach-default", "-D__GNUC__=3", "-D__GNUC_MINOR__=2", "-D__GNUC_PATCHLEVEL__=2", "-D__GXX_ABI_VERSION=102", "-D__ELF__", "-Dunix", "-D__gnu_linux__", "-Dlinux", "-D__ELF__", "-D__unix__", "-D__gnu_linux__", "-D__linux__", "-D__unix", "-D__linux", "-Asystem=posix", "-D__NO_INLINE__", "-D__STDC_HOSTED__=1", "-Acpu=i386", "-Amachine=i386", "-Di386", "-D__i386", "-D__i386__", "-D__tune_i386__", "-D__KERNEL__", "-D__ASSEMBLY__", "-isystem", "/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/include", "-imacros", "include/linux/autoconf.h", "-MD", "arch/i386/kernel/.entry.o.d", "arch/i386/kernel/entry.S", "-o", "/tmp/ccOlsFJR.s"]
Which should execute properly, I think. But it does not:
zach-dev:linux-2.6.14-zach-work $ make
CHK include/linux/version.h
CHK include/linux/compile.h
CHK usr/initramfs_list
AS arch/i386/kernel/entry.o
/usr/lib/gcc-lib/i386-redhat-linux/3.2.2/tradcpp0: output filename specified twice
make[1]: *** [arch/i386/kernel/entry.o] Error 1
make: *** [arch/i386/kernel] Error 2
gcc (GCC) 3.2.2 20030222 (Red Hat Linux 3.2.2-5)
Deprecating the -imacros fixes the build for me. It does not appear to be a
simple argument overflow problem in trapcpp0, since deprecating all the defines
reproduces the problem as well. Also, switching -imacros to -include fixes the
problem.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
XPC (as in arch/ia64/sn/kernel/xp*) has a need to notify other partitions
(SGI Altix) whenever a partition is going down in order to get them to
disengage from accessing the halting partition's memory. If this is not
done before the reset of the hardware, the other partitions can find
themselves encountering MCAs that bring them down.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The previous umad deadlock fix left ib_umad_kill_port() still
vulnerable to deadlocking. This patch fixes that by downgrading our
lock to a read lock when we might end up trying to reacquire the lock
for reading.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In Tavor mode, when posting a long list of receive work requests, a
doorbell must be rung every 256 requests. Add code to do this when
required.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle case where prod_index has wrapped around and become less than
cq->cons_index by checking that their difference as a signed int is
positive rather than comparing directly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The size of work requests for atomic operations was computed
incorrectly in mthca: all sizeofs need to be divided by 16.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the computation of QP capabilities (max scatter/gather entries,
max inline data, etc) into the kernel, and have the uverbs module
return the values as part of the create QP response. This keeps
precise knowledge of device limits in the low-level kernel driver.
This requires an ABI bump, so while we're making changes, get rid of
the max_sge parameter for the modify SRQ command -- it's not used and
shouldn't be there.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that ib_umad uses the new MAD sending interface, it no longer
needs its own L_Key. So just delete the array of MRs that it keeps.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the struct ib_device.resize_cq() method to take a plain integer
that holds the new CQ size, rather than a pointer to an integer that
it uses to return the new size. This makes the interface match the
exported ib_resize_cq() signature, and allows the low-level driver to
update the CQ size with proper locking if necessary.
No in-tree drivers are exporting this method yet.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a typo in the rearming of the catastrophic error polling timer: we
should rearm the timer as long as the stop flag is _not_ set.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For cut-and-paste reasons, the IPoIB driver was setting skb->dev right
before calling dev_kfree_skb_any(). Get rid of this.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_unregister_mad_agent() completes all pending MAD sends and waits
for the agent's send_handler routine to return. umad's send_handler()
calls queue_packet(), which does down_read() on the port mutex to look
up the agent ID. This means that the port mutex cannot be held for
writing while calling ib_unregister_mad_agent(), or else it will
deadlock. This patch fixes all the calls to ib_unregister_mad_agent()
in the umad module to avoid this deadlock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add ibX_path files to debugfs that contain information about the IPoIB
path cache. IPoIB ARP only gives GIDs, which the IPoIB driver must
resolve to real IB paths through the ib_sa module. For debugging,
when the ARP table looks OK but traffic isn't flowing, it's useful to
be able to see if the resolution from GID to path worked.
Also clean up the formatting of the existing _mcg debugfs files.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a task is being traced we never auto-reap it even if it might look
like its parent doesn't care. The tracer obviously _does_ care.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Liam Girdwood
This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.
This patch replaces 2845/1
Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.
The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.
Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
This patch contains changes to common header files for
omap1xxx and omap24xx by various omap developers, and
improved cpu detection by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds omap24xx specific clock code by
Richard Woodruff, Nishant Menon, Tony Lindgren et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds support for omap24xx series of processors.
The files live in arch/arm/mach-omap2, and share common
files with omap15xx and omap16xx processors in
arch/arm/plat-omap.
Omap24xx support was originally added for 2.6.9 by TI.
This code was then improved and integrated to share common
code with omap15xx and omap16xx processors by various
omap developers, such as Paul Mundt, Juha Yrjola, Imre Deak,
Tony Lindgren, Richard Woodruff, Nishant Menon, Komal Shah
et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Serial port and framebuffer init improvments by Imre Deak
- Common omap pin mux framework by Tony Lindgren
- Common omap clock framework by Tony Lindren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Omap1 serial pport and framebuffer init updates by Imre Deak
- Add support for omap310 processor and Palm Tungsten E PDA
by Laurent Gonzales, Romain Goyet, et al. Omap310 and
omap1510 processors are now handled as omap15xx.
- Omap1 specific changes to shared omap clock framework
by Tony Lindgren
- Omap1 specific changes to shared omap pin mux framework
by Tony Lindgren
- Other misc fixes, such as update memory timings for smc91x,
omap1 specific device initialization etc.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds support for the LinkSys NSLU2 running with
both big and little-endian kernels. The LinkSys NSLU2 is
a cost engineered ARM, XScale 420 based system similar to
the the Intel IXDP425 evaluation board. It uses the
IXP4XX ARCH.
While this patch applies independently of other patches
the resultant kernel requires further patches to successfully
use onboard devices, including the onboard flash. Since these
patches are independent of this one they will be submitted
separately.
A defconfig is not included here because not all of
the required drivers are actually in the kernel.
We intend to provide one as soon as the patches
will be incorporated in mainstream.
This patch is the combined work of nslu2-linux.org
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ji-In Park discovered a bug in csumpartial which caused wrong
checksums with misaligned buffers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The i82365 driver does not release all the resources when the device is not
found. This can cause an oops when reading /proc/ioports after module
unload.
Signed-off-by: Igor Popik <igor.popik@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
For now, we need these declarations that we moved from C code in
the asm-ppc64 versions of these headers as well as the asm-powerpc
versions. The asm-ppc64 versions will be disappearing shortly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
19-rpaphp-crashing.patch
This patch fixes a bug related to dlpar PHB add, after a PHB removal.
-- The crash was due to the PHB not having a pci_dn structure yet,
when the phb is being added.
This code survived testing, of adding and removeig the PHB and all slots
underneath it, 17 times so far, as of this writing.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch more files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
hvcall.h
proc_ppc64.c
sysfs.c
lparcfg.c
rtas_pci.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.
This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.
That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
That DART (U3 iommu) code didn't properly scale the number of entries
when using !4k pages. That caused crashes when booting G5s with more
than 2Gb of RAM. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes the kernel use a different kmem cache for PMD pages
as they are smaller than PTE pages. Avoids waste of memory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the call to xprt_transmit() fails due to socket buffer space
exhaustion, we do not need to re-encode the RPC message when we
loop back through call_transmit.
Re-encoding can actually end up triggering the WARN_ON() in
call_decode() if we re-encode something like a read() request and
auth->au_rslack has changed.
It can also cause us to increment the RPCSEC_GSS sequence number
beyond the limits of the allowed window.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes the memory examine/change command print the address as
8 digits instead of 16, and makes the memory dump command print
4 4-byte values per line instead of 2 8-byte values.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is at the request of the glibc folks, who want to use these bits
to select libraries optimized for the microarchitecture and new
instructions in these processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were getting the last_jiffy per-cpu variable set ahead of the current
timebase in smp_space_timers on SMP machines. This caused the loop in
timer_interrupt to loop virtually forever, since tb_ticks_since assumes
that it will never be called with the timebase behind the last_jiffy
value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scanlog.c is only compiled on pSeries. Thus, this patch moves it to
platforms/pseries.
Built and booted on pSeries LPAR (ARCH=powerpc and ARCH=ppc64). Built
for iSeries (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The generic netlink family builds on top of netlink and provides
simplifies access for the less demanding netlink users. It solves
the problem of protocol numbers running out by introducing a so
called controller taking care of id management and name resolving.
Generic netlink modules register themself after filling out their
id card (struct genl_family), after successful registration the
modules are able to register callbacks to command numbers by
filling out a struct genl_ops and calling genl_register_op(). The
registered callbacks are invoked with attributes parsed making
life of simple modules a lot easier.
Although generic netlink modules can request static identifiers,
it is recommended to use GENL_ID_GENERATE and to let the controller
assign a unique identifier to the module. Userspace applications
will then ask the controller and lookup the idenfier by the module
name.
Due to the current multicast implementation of netlink, the number
of generic netlink modules is restricted to 1024 to avoid wasting
memory for the per socket multiacst subscription bitmask.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces netlink_run_queue() to handle the receive queue of
a netlink socket in a generic way. Processes as much as there
was in the queue upon entry and invokes a callback function
for each netlink message found. The callback function may
refuse a message by returning a negative error code but setting
the error pointer to 0 in which case netlink_run_queue() will
return with a qlen != 0.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most netlink families make no use of the done() callback, making
it optional gets rid of all unnecessary dummy implementations.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new type-safe interface for netlink message and
attributes handling. The interface is fully binary compatible
with the old interface towards userspace. Besides type safety,
this interface features attribute validation capabilities,
simplified message contstruction, and documentation.
The resulting netlink code should be smaller, less error prone
and easier to understand.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a "64" that didn't get changed to BITS_PER_LONG, resulting
in find_next_bit not working correctly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine. On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.
The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
11-eeh-move-to-powerpc.patch
Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
10-EEH-enable-bugfix.patch
Bugfix: With the curent linux-2.6.14-rc2-git6, EEH errors are
ignored because thier detection requires an unused, uninitialized
flag to be set. This patch removes the unused flag.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
09-hotplug-bugfix.patch
In the current 2.6.14-rc2-git6 kernel, performing a Dynamic LPAR Add
of a hotplug slot will crash the system, with the following (abbreviated)
stack trace:
cpu 0x3: Vector: 700 (Program Check) at [c000000053dff7f0]
pc: c0000000004f5974: .__alloc_bootmem+0x0/0xb0
lr: c0000000000258a0: .update_dn_pci_info+0x108/0x118
c0000000000257c8 .update_dn_pci_info+0x30/0x118 (unreliable)
c0000000000258fc .pci_dn_reconfig_notifier+0x4c/0x64
c000000000060754 .notifier_call_chain+0x68/0x9c
The root cause was that __init __alloc_bootmem() was called long after
boot had finished, resulting in a crash because this routine is undefined
after boot time. The patch below fixes this crash, and adds some docs to
clarify the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
08-eeh-spin-counter.patch
One an EEH event is triggers, all further I/O to a device is blocked (until
reset). Bad device drivers may end up spinning in their interrupt handlers,
trying to read an interrupt status register that will never change state.
This patch moves that spin counter to a per-device structure, and adds
some diagnostic prints to help locate the bad driver.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
07-eeh-report-race.patch
When a PCI slot is isolated, all PCI functions under that slot are affected.
If hese functions have separate device drivers, the EEH isolation event
might be reported multiple times. This patch adds a lock to prevent the
racing of such multiple reports. It also marks every device under the slot
as having experienced an EEH event, so that multiple reports may be
recognized more easily.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
06-eeh-empty-slot-error.patch
Performing PCI config-space reads to empty PCI slots can lead to reports of
"permanent failure" from the firmware. Ignore permanent failures on empty slots.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
05-eeh-slot-error-detail.patch
This patch encapsulates a section of code that reports the EEH event.
The new subroutine can be used in several places to report the error.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
04-eeh-statistics.patch
This minor patch adds some statistics-gathering counters that allow the
behaviour of the EEH subsystem o be monitored. While far from perfect,
it does provide a rudimentary device that makes understanding of the
current state of the system a bit easier.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
03-eeh-addr-cache-cleanup.patch
This is a minor patch to clean up a buglet related to the PCI address cache.
(The buglet doesn't manifes itself unless there are also bugs elsewhere,
which is why its minor.). Also:
-- Improved debug printing.
-- Declare some private routines as static
-- Adds reference counting to struct pci_dn->pcidev structure
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
02-eeh-minor-cleanup.patch
This patch performs some minor cleanup of the eeh.c file, including:
-- trim some trailing whitespace
-- remove extraneous #includes
-- use the macro PCI_DN uniformly, instead of the void pointer chase.
-- typos in comments
-- improved debug printk's
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
01-pci-dn-uniformization.patch
This patch changes the rtas_pci interface to use the new struct pci_dn
structure for two routines that work with pci device nodes.
This patch also does some minor janitorial work: it uses some handy macros
and cleans up some trailing whitespace in the affected file.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Early calls to __ioremap() will panic if the hash insertion fails. This
patch makes them return NULL instead. It happens with some pSeries users
who enabled CONFIG_BOOTX_TEXT. The later is getting an incorrect address
for the fame buffer and the hash insertion fails. With this patch, it
will display an error instead of crashing at boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a few compile warnings
arch/ppc64/boot/addRamDisk.c:166: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:170: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:265: warning: unsigned int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:302: warning: unsigned int format, long unsigned int arg (arg 3)
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A stripped vmlinux does not contain enough symbols to recreate the
System.map. The System.map file is only used to determine the end of
the runtime memory size. This is the same value (rounded up to
PAGE_SIZE) as ->memsiz in the ELF program header.
Also, the target vmlinux.initrd doesnt work in 2.6.14:
arch/ppc64/boot/addRamDisk arch/ppc64/boot/ramdisk.image.gz vmlinux.strip arch/ppc64/boot/vmlinux.initrd
Name of vmlinux output file missing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove initialization of local variables.
They get all values assigned before use.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Due to the recent update of the platform code, some platform device
drivers fail to compile. This fix is for fs_enet, adding #include of a
new header, to which a number of platform stuff has been relocated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes ppc44x fpu support that broke from a bad arch/powerpc merge.
Instead of adding KernelFP back in (which duplicates code) we use
the same kernel fpu unavailable handler as classic PPC processors.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges current.h. This is a one-big-ifdef merge, but both
versions are so tiny, I think we can live with it. While we're at it,
we get rid of the fairly pointless redirection through get_current()
in the ppc64 version.
Built and booted on POWER5 LPAR (ARCH=powerpc & ARCH=ppc64). Built
for 32-bit pmac (ARCH=powerpc & ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Re-add a hunk lost during merge: ppc64 is missing the hunk that disables
preempt on the secondary CPUs before they call cpu_idle().
- ppc's cpu_idle() had the need_resched() test wrong.
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
recalc_task_prio() is called from activate_task() to calculate dynamic
priority and interactive credit for the activating task. For real-time
scheduling process, all that dynamic calculation is thrown away at the end
because rt priority is fixed. Patch to optimize recalc_task_prio() away
for rt processes.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <piggin@cyberone.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem (eject not working on ATAPI LS-120 drive) is caused by
idefloppy_ioctl() function which *first* tries generic_ide_ioctl()
and *only* if it fails with -EINVAL, proceeds with the specific ioctls.
The generic eject command fails with something other than -EINVAL
and the specific one is never executed.
This patch fixes it by first going through the internal ioctls
and only trying generic_ide_ioctl() if none of them matches.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
wbsd_*_remove() is declared as __devexit but __devexit_p isn't used
when taking their addresses.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The siimage driver proports to support the Adaptec SA-1210 SATA
controller. However, at least some of those cards boot-up with their
interrupts disabled internally. The siimage driver currently ignores
that fact, so that driver does not actually work with those cards.
This patch enables those interrupts on cards that need it.
[ This is implemented based on similar code in the libata-based
sata_sil driver. ]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Matthew Wilcox asked that this got a comment explaining why it is done
so here it is.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
AGP shouldn't use "global_flush_tlb()" to flush the AGP mappings, that i
spurely an x86'ism. The proper AGP mapping flusher that should be used
is "flush_agp_mappings()", which on x86 obviously happens to do a global
TLB flush.
This makes AGP (or at least the config _I_ happen to use) compile again
on ppc64.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
From: "Jordan Crouse" <jordan.crouse@amd.com>
The core IDE engine on the CS5536 is the same as the other AMD southbridges,
so unlike the CS5535, we can simply add the appropriate PCI headers to
the existing amd74xx code.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=160868
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
The patch below makes ide-scsi whole.
Signed-off-by: Willem Riede <wrlk@riede.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch contains the following possible cleanups:
- pci/cy82c693.c: make a needlessly global function static
- remove the following unneeded EXPORT_SYMBOL's:
- ide-taskfile.c: do_rw_taskfile
- ide-iops.c: default_hwif_iops
- ide-iops.c: default_hwif_transport
- ide-iops.c: wait_for_ready
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CONFIG_IDE_MAX_HWIFS is a generic thing, no need to have it duplicated
by every arch that uses it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices driven by ide-cs will appear under /sys/devices instead of the
appropriate PCMCIA device. To fix this I had to extend the hw_regs_t
structure with a 'struct device' field, which allows us to set the
parent link for the appropriate hwif.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The return data from a read capacity 16 needs to have RTO_EN and PROT_EN
zeroed out.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Trying to build today's 2.6.14+git snapshot gives undefined references
to use_tempaddr
Looks like an ifdef got left out.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an userspace triggered oops. If there is no ICMP_ID
info the reference to attr will be NULL.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the error to userspace instead of returning -EPERM if the get
conntrack operation fails.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently connection tracking handles ICMP error like normal packets
if it failed to get related connection. But it fails that after all.
This makes connection tracking stop tracking ICMP error at early point.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, any user can cause nfnetlink subsystems to be
autoloaded. Those subsystems however could add significant processing
overhead to packet processing, and would refuse any configuration messages
from non-CAP_NET_ADMIN processes anyway.
This patch follows a suggestion from Patrick McHardy.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reply tuple of the PNS->PAC expectation was using the wrong call id.
So we had the following situation:
- PNS behind NAT firewall
- PNS call id requires NATing
- PNS->PAC gre packet arrives first
then the PNS->PAC expectation is matched, and the other expectation
is deleted, but the PAC->PNS gre packets do not match the gre conntrack
because the call id is wrong.
We also cannot use ip_nat_follow_master().
Signed-off-by: Philip Craig <philipc@snapgear.com>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ctnetlink_get_conntrack is always called from user context, so GFP_KERNEL
is enough.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill some useless headers included in ctnetlink. They aren't used in any
way.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing module alias. This is a must to load ctnetlink on demand. For
example, the conntrack tool will fail if the module isn't loaded.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an oops triggered from userspace. If we don't pass information
about the private protocol info, the reference to attr will be NULL. This is
likely to happen in update messages.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfattr_parse (and thus nfattr_parse_nested) always returns success. So we
can make them 'void' and remove all the checking at the caller side.
Based on original patch by Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of ARRAY_SIZE which is never used anyways.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of ARRAY_SIZE which is never used anyways.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we did CLONE_THREAD, the way to check whether we were attaching
to ourselves was to just check "current == task", but with CLONE_THREAD
we should check that the thread group ID matches instead.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce struct platform_driver. This allows the platform device
driver methods to be passed a platform_device structure instead of
instead of a plain device structure, and therefore requiring casting
in every platform driver.
We introduce this in such a way that any existing platform drivers
registered directly via driver_register continue to work as before,
thereby allowing a gradual conversion to the new platform_driver
methods.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following previously global and EXPORT_SYMBOL'ed
code static:
- struct mpt_proc_root_dir
- int mpt_stm_index
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Document in Documentation/md.txt the files that now appear in sysfs, and make
a couple of small refinements to exactly when 'level' and 'raid_disks' are
empty, to make it match the documentation.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current sync_action for an array can be one of
idle - nothing happening
resync - reduncancy being recalcualted
recover - missing device being recoverred to spare
check - user initiated check of redundancy
repair - like resync but user-initiated and ignores
bitmap optimisation.
Each of these strings can also be written to the 'sync_action' file to cause
that action to happen (if appropriate).
While 'sync' is not technically correct, as a recovery is *not* a 'sync', I
think it is the most servicable word here. Also 'action' is a strong word
than 'mode'.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a few loose ends following the conversion of md to use kthreads:
- Some fields in mdk_thread_t that aren't needed (kthreads does it's own
completion and manages it's own name).
- thread->run is now never NULL, so no need to check
- Some tests for signal_pending that aren't needed (As we don't use signals
to stop threads any more)
- Some flush_signals are not needed
- Some waits are interruptible and don't need to be.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'auto-readonly' flag (which suppresses resync and superblock updates until
the first write) is not meaningful for personalities that don't support resync
or superblock writes (raid0, linear, etc).
So clear the setting early to avoid it confusing anything - e.g. appearing in
/proc/mdstat
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The introduction of 'resync=PENDING' (for read-only devices) caused that
message to appear for non-syncable arrays like raid0 and linear. Simplest
thing is to not try to print any resync info unless the personality clearly
supports it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some, but not all, md array support data redundancy and hence support checking
and restoring that redundancy (resync, rebuild).
Some attributes apply specifically to functions involving this redundancy, and
so should only appear for md arrays for which they are meaningful. i.e. they
should not appear for raid0, linear, multpath, faulty.
This patch separates these into a distinct group and creates the group only if
the personality supports sync_request.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ I really should be using the __ATTR macros for defining attributes, so
that the .owner field get set properly, otherwise modules can be removed
while sysfs files are open. This also involves some name changes of _show
routines.
2/ Always lock the mddev (against reconfiguration) for all sysfs attribute
access. This easily avoid certain races and is completely consistant with
other interfaces (ioctl and /proc/mdstat both always lock against
reconfiguration).
3/ raid5 attributes must check that the 'conf' structure actually exists
(the array could have been stopped while an attribute file was open).
4/ A missing 'kfree' from when the raid5_conf_t was converted to have a
kobject embedded, and then converted back again.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A sync of raid5 usually ignore blocks which the bitmap says are in-sync. But
a user-request check or repair should not ignore these.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Raid1 currently optimises resync using the intent bitmap etc. This
optimisation is not wanted when we explicitly request a repair through sysfs,
so add appropriate checks.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a block_device is a partition, then it's kobject is
bdev->bd_part->kobj
otherwise (if it is a full device), the kobject is
bdev->bd_disk->kobj
As md wants back-links to the correct object (whether partition or not), we
need to respect this difference... (Thus current code shows a link to the
whole device, whether we are using a partition or not, which is wrong).
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an md array is started, the superblock will be written, and resync may
commense. This is not good if you want to be completely read-only as, for
example, when preparing to resume from a suspend-to-disk image.
So introduce a module parameter "start_ro" which can be set
to '1' at boot, at module load, or via
/sys/module/md_mod/parameters/start_ro
When this is set, new arrays get an 'auto-ro' mode, which disables all
internal io (superblock updates, resync, recovery) and is automatically
switched to 'rw' when the first write request arrives.
The array can be set to true 'ro' mode using 'mdadm -r' before the first
write request, or resync can be started without a write using 'mdadm -w'.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With version-0.90 superblock, component devices on an md device to not have
any stable name related to the array -(version-1 assigns a fixed index when
a device is added to an array, and this remains despit any hot-swap).
The intial code for making these devices appear in sysfs used dynamic
names, which would change whenever a hot-spare was swapped for a failed or
missing device. This turns out not to be practical in sysfs for a number
of reasons.
This patch changes then naming of component devices to be based on the
result of 'bdevname'. This is stable and should be unique.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can only accept BARRIER requests if all slaves handle
barriers, and that can, of course, change with time....
So we keep track of whether the whole array seems safe for barriers,
and also whether each individual rdev handles barriers.
We initially assumes barriers are OK.
When writing the superblock we try a barrier, and if that fails, we flag
things for no-barriers. This will usually clear the flags fairly quickly.
If writing the superblock finds that BIO_RW_BARRIER is -ENOTSUPP, we need to
resubmit, so introduce function "md_super_wait" which waits for requests to
finish, and retries ENOTSUPP requests without the barrier flag.
When writing the real raid1, write requests which were BIO_RW_BARRIER but
which aresn't supported need to be retried. So raid1d is enhanced to do this,
and when any bio write completes (i.e. no retry needed) we remove it from the
r1bio, so that devices needing retry are easy to find.
We should hardly ever get -ENOTSUPP errors when writing data to the raid.
It should only happen if:
1/ the device used to support BARRIER, but now doesn't. Few devices
change like this, though raid1 can!
or
2/ the array has no persistent superblock, so there was no opportunity to
pre-test for barriers when writing the superblock.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current bitmaps use set_bit et.al and so are host-endian, which means
not-portable. Oops.
Define a new version number (4) for which bitmaps are little-endian.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two refinements to the 'attempt-overwrite-on-read-error' mechanism.
1/ If the array is read-only, don't attempt an over-write.
2/ If there are more than max_nr_stripes read errors on a device with
no success, fail the drive. This will make sure a dead
drive will be eventually kicked even when we aren't trying
to rewrite (which would normally kick a dead drive more quickly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There isn't really a need for raid5 attributes to be an a subdirectory,
so this patch moves them from
/sys/block/mdX/md/raid5/attribute
to
/sys/block/mdX/md/attribute
This suggests that all md personalities should co-operate about
namespace usage, but that shouldn't be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ Use reduce stack usage, because 'gcc' apparently doesn't overlay
different variables that are in separate scopes...
2/ Use test_bit instead of ( .. & 1<< ..) which in this case is buggy.
Thanks to Andrew Morton
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this, raid5 can be asked to check parity without repairing it. It also
keeps a count of the number of incorrect parity blocks found (mismatches) and
reports them through sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
You can trigger a 'check' with
echo check > /sys/block/mdX/md/scan_mode
or a check-and-repair errors with
echo repair > /sys/block/mdX/md/scan_mode
and read the current state from the same file.
Note: personalities need to know the different between 'check' and 'repair',
but don't yet. Until they do, 'check' will be the same as 'repair' and will
just do a normal resync pass.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/sys/block/mdX/md/raid5/
contains raid5-related attributes.
Currently
stripe_cache_size
is number of entries in stripe cache, and is settable.
stripe_cache_active
is number of active entries, and in only readable.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Each device in an md array how has a corresponding
/sys/block/mdX/md/devNN/
directory which can contain attributes. Currently there is only 'state' which
summarises the state, nd 'super' which has a copy of the superblock, and
'block' which is a symlink to the block device.
Also, /sys/block/mdX/md/rdNN represents slot 'NN' in the array, and is a
symlink to the relevant 'devNN'. Obviously spare devices do not have a slot
in the array, and so don't have such a symlink.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Start using kobjects in mddevs, and provide a couple of simple attributes
(level and disks). Attributes live in
/sys/block/mdX/md/attr-name
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the behaviour of raid5 when it gets a read error.
Instead of just failing the device, it tried to find out what should have
been there, and writes it over the bad block. For some media-errors, this
has a reasonable chance of fixing the error. If the write succeeds, and a
subsequent read succeeds as well, raid5 decided the address is OK and
conitnues.
Instead of failing a drive on read-error, we attempt to re-write the block,
and then re-read. If that all works, we allow the device to remain in the
array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The frame buffer layer already had some code dealing with compat ioctls, this
patch moves over the remaining code from fs/compat_ioctl.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete leftovers of the FB_E1356 and anything that did depend on it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix possible endian bug(?) when bit testing in slow_imageblit(). This
function is rarely called (only if (width * bpp) % 32 != 0) thus the bug is
not triggered.
However, if the console is rotated at 90 or 270 degrees, the height becomes
the width, and a variety of fonts have heights that will force a call to
slow_imageblit().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add documentation as Documentation/fb/fbcon.txt describing the framebuffer
console and its boot options.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ability to set rotation via sysfs. The attributes are located in
/sys/class/graphics/fb[n] and accepts 0 - unrotated; 1 - clockwise; 2 - upside
down; 3 - counterclockwise.
The attributes are:
con_rotate (r/w) - set rotation of the active console
con_rotate_all (w) - set rotation of all consoles
rotate (r/w) - set rotation of the framebuffer, if supported.
Currently, none of the drivers support this.
This is probably temporary, since con_rotate and con_rotate_all are
console-specific and has no business being under the fb device. However,
until the console layer acquires it's own sysfs class, these attributes will
temporarily reside here.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 270-degree (counterclockwise) rotation of the console. To
activate, boot with:
fbcon=rotate:3
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 180-degree (upside down) rotation of the console. To
activate, boot with:
fbcon=rotate:2
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for 90-degree (clockwise) rotation of the console. To activate,
boot with:
fbcon=rotate:1
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to rotate the font bitmap. To save on processing time, the entire
fontdata will be rotated on a console switch, then stored in a buffer private
to fbcon. To further save on processing, the fontdata will only be rotated if
the font has changed or if the angle of rotation has changed. Only a single
copy of the rotated fontdata will be kept.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for rotating and positioning of the logo. Rotation and position
depends on 'int rotate' parameter added to fb_prepare_logo() and
fb_show_logo().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch series implements generic code to rotate the console at 90, 180,
and 270 degrees. The implementation is completely done in the framebuffer
console level, thus no changes to the framebuffer layer or to the drivers
are needed.
Console rotation is required by some Sharp-based devices where the natural
orientation of the display is not at 0 degrees. Also, users that have
displays that can pivot will benefit by having a console in portrait mode
if they so desire.
The choice to implement the code in the console layer rather than in the
framebuffer layer is due to the following reasons:
- it's fast
- it does not require driver changes
- it can coexist with devices that can rotate the display at the hardware level
- it complements graphics applications that can do display rotation
The changes to core fbcon are minimal-- recognition of the console
rotation angle so it can swap directions, origins and axes (xres vs yres,
xpanstep vs ypanstep, xoffset vs yoffset, etc) and storage of the rotation
angle per display. The bulk of the code that does the actual drawing to the
screen are placed in separate files. Each angle of rotation has separate
methods (bmove, clear, putcs, cursor, update_start which is derived from
update_var, and clear_margins). To mimimize processing time, the fontdata
are pre-rotated at each console switch (only if the font or the angle has
changed).
The option can be compiled out (CONFIG_FRAMEBUFFER_CONSOLE_ROTATION = n) if
rotation is not needed.
Choosing the rotation angle can be done in several ways:
1. boot option fbcon=rotate:n, where
n = 0 - normal
n = 1 - 90 degrees (clockwise)
n = 2 - 180 degrees (upside down)
n = 3 - 270 degrees (counterclockwise)
2. echo n > /sys/class/graphics/fb[num]/con_rotate
where n is the same as described above. It sets the angle of rotation
of the current console
3 echo n > /sys/class/graphics/fb[num]/con_rotate_all
where n is the same as described above. Globally sets the angle of
rotation.
GOTCHAS:
The option, especially at angles of 90 and 270 degrees, will exercise
the least used code of drivers. Namely, at these angles, panning is done
in the x-axis, so it can reveal bugs in the driver if xpanstep is set
incorrectly. A workaround is to set xpanstep = 0.
Secondly, at these angles, the framebuffer memory access can be
unaligned if (fontheight * bpp) % 32 ~= 0 which can reveal bugs in the drivers
imageblit, fillrect and copyarea functions. (I think cfbfillrect may have
this buglet). A workaround is to use a standard 8x16 font.
Speed:
The scrolling speed difference between 0 and 180 degrees is minimal,
somewhere areound 1-2%. At 90 or 270 degress, speed drops down to a vicinity
of 30-40%. This is understandable because the blit direction is across the
framebuffer "direction." Scrolling will be helped at these angles if xpanstep
is not equal to zero, use of 8x16 fonts, and setting xres_virtual >= xres * 2.
Note: The code is tested on little-endian only, so I don't know if it will
work in big-endian. Please let me know, it will take only less than a minute
of your time.
This patch prepares fbcon for console rotation and contains the following
changes:
- add rotate field in struct fbcon_ops to keep fbcon's current rotation
angle
- add con_rotate field in struct display to store per-display rotation angle
- create a private copy of the current var to fbcon. This will prevent
fbcon from directly manipulating info->var, especially the fields xoffset,
yoffset and vmode.
- add ability to swap pertinent axes (xres, yres; xpanstep, ypanstep; etc)
depending on the rotation angle
- change global update_var() (function that sets the screen start address)
as an fbcon method update_start. This is required because the axes, start
offset, and/or direction can be reversed depending on the rotation angle.
- add fbcon method rotate_font() which will rotate each character bitmap to
the correct angle of rotation.
- add fbcon boot option 'rotate' to select the angle of rotation at bootime.
Currently does nothing until all patches are applied.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the framebuffer mode required for an Apple PowerBook G4
Titanium.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver unconditionally sets xpanstep to 2. However, a value of 4
empirically works better at bpp = 8, and 2 for 16 and 32. This buglet was
exposed by the rotation code.
Second fix is the unconditional call to update_start() without verifying if
the offsets are correct. Remove this call, it's not necessary and secondly,
it causes a crash with invalid values.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The intermittent scheduling of the migration thread at ultra high priority
makes the smp nice handling see that runqueue as being heavily loaded. The
migration thread itself actually handles the balancing so its influence on
priority balancing should be ignored.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The priority biasing was off by mutliplying the total load by the total
priority bias and this ruins the ratio of loads between runqueues. This
patch should correct the ratios of loads between runqueues to be proportional
to overall load. -2nd attempt.
From: Dave Kleikamp <shaggy@austin.ibm.com>
This patch fixes a divide-by-zero error that I hit on a two-way i386
machine. rq->nr_running is tested to be non-zero, but may change by the
time it is used in the division. Saving the value to a local variable
ensures that the same value that is checked is used in the division.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To intensify the 'nice' support across physical cpus on SMP we can bias the
loads on idle rebalancing. To prevent idle rebalance from trying to pull tasks
from queues that appear heavily loaded we only bias the load if there is more
than one task running.
Add some minor micro-optimisations and have only one return from __source_load
and __target_load functions.
Fix the fact that target_load was not biased by priority when type == 0.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Real time tasks' effect on prio_bias should be based on their real time
priority level instead of their static_prio which is based on nice.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements 'nice' support across physical cpus on SMP.
It introduces an extra runqueue variable prio_bias which is the sum of the
(inverted) static priorities of all the tasks on the runqueue.
This is then used to bias busy rebalancing between runqueues to obtain good
distribution of tasks of different nice values. By biasing the balancing only
during busy rebalancing we can avoid having any significant loss of throughput
by not affecting the carefully tuned idle balancing already in place. If all
tasks are running at the same nice level this code should also have minimal
effect. The code is optimised out in the !CONFIG_SMP case.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Saa7134-alsa can only be autoloaded after saa7134 is active
- Applied pertinent changes proposed by the ALSA team
- dsp_nr replaced by ALSA's index[]
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed autodetection of max size by if alternate setting
- Fixed some debug messages
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Adds missing msp34xxg_reset to VIDIOC_S_STD (just like VIDIOCSCHAN).
- Improves msp3400 debug messages.
Now, all kernel message in msp3400.c use the same prefix
and include the I2C bus to differentiate between multiple
msp3400 I2C chips.
- Correctly prints the chip identifier for the msp44xx chips.
- msp34xxg cleanups.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SAA713x cards with i2c remotes now autoload ir-kbd-i2c (disable_ir works, as
it does for GPIO remotes)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Em28xx cleanups and fixes.
- Some cleanups and audio amux adjust.
- em28xx will allways try, by default, the biggest size alt.
- Fixes audio mux code.
- Fixes some logs.
- Adds support for digital output for WinTV USB2 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix RDS raw data buffer handling bug, which caused decoding delays and
sometimes wrong data.
Signed-off-by: Hans J. Koch <koch@hjk-az.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Module em2820 renamed to em28xx and moved to V4L dir.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Some cleanups at I2C stuff and fixing when tuner addr is set.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move cx88 and saa7134 configuration out of
drivers/media/video/Kconfig and instead, use
new Kconfig files in each respective directory.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix bug 5484: ASUS digimatrix card doesnt work with PAL tuner
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- VIDIOC_LOG_STATUS is added to videodev2.h this can be enabled
again in wm8775.c. Also use the v4l2 VIDIOC_S_FREQUENCY instead of
VIDIOCSFREQ.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Some changes to allow compiling cx88 and saa7134 without V4L1 support.
- This patch will help obsoleting V4L1 API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- After msp34xxg_reset, msp_wake_thread should be called to
wake again.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- This patch adds the VIDIOC_LOG_STATUS to videodev2.h and adds
LOG_STATUS support to tda9887.c and bttv-driver.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Several Improvement on I2C IR handling for em2820:
- moved Pinnacle IR table (ir_codes_em2820) to em2820-input.c
- IR struct renamed and moved to a header file.
- New file to handle em2820-specific IR.
- Some cleanups.
- attach now detects I2C IR and calls em2820-specific IR code
- IR compat code moved to compat.h
- New header with struct IR_i2c there, to allow it to be
used by board-specific input handlers.
- Some improvements at em28xx board detection:
- Board detection message improved to show interface and class.
- Now it doesn't touch audio interfaces.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed bad em2820 remote layout values
- set KNC One and Purple TV layouts back to default
- added pinnacle ir remote i2c address to the i2c scanner
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed registry value in em2820-i2c.c which corrects a tuner setting (also
removed that call from em2820-video.c)
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Created make changelog to make easier to generate patches.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- BTTV Boards now use the same CodingStyle as cx88 and saa7134.
- Included missing card numbers
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Change the number of lines in the input signal when the video standard is
changed.
- Fix comments style.
Signed-off-by: Robert W. Boone <rboone@rtd.com>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed gcc 4.0 compile warnings by moving var declarations to the top of
the function or block.
Signed-off-by: Catalin Climov <catalin@climov.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added support for OEM version of FlyTV Platinum mini with a subvendor id
of 0x4e42.
- Added the OEM PCI id's to the docs/CARDLIST.saa7134 for item 39
- Modified the vmux in the SAA7134_BOARD_FLYTVPLATINUM_MINI driver data from
0 (Composite over S-Video) to 3 (Composite).
Signed-off-by: Glen Gray <glen@lincor.com>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added function for nxt200x to change pll input
- For VSB set to input 0, for QAM set to input 1
- will only be set for cards that have set_pll_input defined
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct QAM symbol_rate_min for lgdt3302 and lgdt3303
Thanks to: Mac Michaels and Steve Malenfant
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/media/dvb/dvb-usb/dvb-usb-urb.c: In function `dvb_usb_allocate_stream_buffers':
drivers/media/dvb/dvb-usb/dvb-usb-urb.c:199: warning: int format, different type arg (arg 4)
Don't assume that dma_addr_t is 32-bit.
(dvb has quite a few such warnings. Please compile it with a 64-bit compiler,
fix them up - some are oopsable).
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated documentation to include "hybrid" v4l/dvb and ATSC cards.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove status check from nxt200x_readreg_multibyte, it really shouldn't be
necessary.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in the software demux which causes large MPEG sections to be lost
when they follow very small sections.
The problem happens when two sections begin in the same transport packet. The
dvb_demux code resets its buffer only before the first of these sections.
This means that when the second (or subsequent) section begins, there is up to
182 bytes of buffer space already used. If the following section is close to
the maximum size, it currently won't fit in the (4096-byte) buffer and is
thrown away.
The fix is simply to enlarge the buffer by the size of one transport packet
and correct one usage of the SECFEED_SIZE definition where what is really
meant is the maximum size of a section.
Signed-off-by: Mark Adams <mark147m@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add support for AVerTVHD MCE a180.
- Instead of determining how to write to the tuner based on which NIM
is being used, make this determination based on whether the chip is a
NXT2002 or NXT2004.
- If NXT2004, write directly to tuner. If NXT2002, write through NXT chip.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed unnecessary null check before kfree() ...inspired by the big patch
from Jesper Juhl.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check that a callback (set_ts_params) is set before calling it.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* nxt200x.c, nxt200x.h
- New frontend module that supports both NXT2002 and NXT2004.
So far, only tested on NXT2004. After testing on NXT2002, we should
deprecate the nxt2002 module, and implement this one instead on the
applicable cards.
* get_dvb_firmware:
- Added support for the NXT2004 firmware. This firmware works with both
the ATI HDTV Wonder and the AVerTVHD MCE a180.
This was originally written by Jean-Francois Thibert
* dvb-pll.c
- Fixed minimum frequency for tuv1236d. It seems that the data sheets
are wrong.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stv0299_set_frontend(): reduced number of i2c transfers, set register 0x12
from inittab
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added support for the following:
Philips TUV1236D - ATI HDTV Wonder
ALPS TDHU2 - AverTVHD MCE A180
Samsung TBMV30111IN - Air2PC ATSC - 2nd generation
These will be used in a new NXT200X driver that incorporates the NXT2002
driver and adds support for a couple NXT2004 based cards.
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Updated documentation for FusionHDTV Lite cards. We must differentiate
the bt8xx based "Lite" cards from the cx2388x based "Gold" cards.
- Provide location of CARDLIST.bttv Documentation, rather than
instructing users to look at bttv.h
- Include card decimal id numbers. These are valid for module arguments,
and might be easier for some people to remember, rather than hex.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support to FE_DISHNETWORK_SEND_LEGACY_CMD code to support other frontends
besides stv0299. The generic code is a fallback in the case that it doesn't
work for some specific frontends (again stv0299 being a good example).
Signed-off-by: NooneImportant <nxhxzi702@sneakemail.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix integer overflow bug in read_signal_strength() reported by Anthony
Leclerc.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix charge pump setting in microtune_mt7202dtf_pll_set(). Thanks to Jyrki
Niskala for reporting.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The duplicate key definitions cause misinterpretations with other keys, e.g.
the "TELETEXT" key clashes with "CHANNEL_UP" and thus can not be used with
LIRC. This patch removes these duplicates.
Signed-off-by: Thorsten Maerz <torte@netztorte.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- leave I2C bridge open at pll_sleep to support Philips EUROPA based cards.
- give an error message if the communication with the pll fails.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures define and use this type in their compat_ioctl code, but
all of them can easily use the identical ioctl_trans_handler_t type that is
defined in common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't implement these ioctls, but some architectures define them in the
headers. Bash picks them up and issues them frequently. Add compat_ioctl
handlers to silence warnings about unhandled copat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
->permission and ->lookup have a struct nameidata * argument these days to
pass down lookup intents. Unfortunately some callers of lookup_hash don't
actually pass this one down. For lookup_one_len() we don't have a struct
nameidata to pass down, but as this function is a library function only
used by filesystem code this is an acceptable limitation. All other
callers should pass down the nameidata, so this patch changes the
lookup_hash interface to only take a struct nameidata argument and derives
the other two arguments to __lookup_hash from it. All callers already have
the nameidata argument available so this is not a problem.
At the same time I'd like to deprecate the lookup_hash interface as there
are better exported interfaces for filesystem usage. Before it can
actually be removed I need to fix up rpc_pipefs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few more callers of permission() just want to check for a different access
pattern on an already open file. This patch adds a wrapper for permission()
that takes a file in preparation of per-mount read-only support and to clean
up the callers a little. The helper is not intended for new code, everything
without the interface set in stone should use vfs_permission()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most permission() calls have a struct nameidata * available. This helper
takes that as an argument and thus makes sure we pass it down for lookup
intents and prepares for per-mount read-only support where we need a struct
vfsmount for checking whether a file is writeable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Found this on Coverty's linux bug database (http://linuxbugsdb.coverity.com).
The function pkt_iosched_process_queue makes a call to bdev_get_queue and
stores the result but never uses it, so it looks like it can be safely
removed.
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes an ancient changelog file.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CONFIG_EXT{2,3}_CHECK options where were never available, and all they
did was to implement a subset of e2fsck in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make reiserfs correctly return EDQUOT when the allocation failed due to
quotas (so far we just returned ENOSPC).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass down the silent flag to parse_options(). Without this fat gives
warnings when mounting some non-fat rootfs with options.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some more checks during the parsing of .config, so that after parsing
sym_change_count reflects the correct state whether the .config is correct and
in sync with the Kconfig or if it needs saving.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a few error tokens to the parser to catch common errors and print more
descriptive error messages.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This simplifies the parser a bit by merging the various symbol types into a
single token and adds the type to the keyword hash.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use gperf to generate a hash for the kconfig keywords. This greatly reduces
the size of the generated scanner and makes it easier to extend kconfig.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the long obsolete zconf.tab.h and fix kconfig make rules to generate
the correct output files. Setting LKC_GENPARSER will now also update the
shipped files.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow to force setting of config variables during all{no,mod,yes,random}config
to a specific value. For that conf first checks the KCONFIG_ALLCONFIG
environment variable for a file name, otherwise it checks for
all{no,mod,yes,random}.config and all.config. The file is a normal config
file, which presets the config variables, but they are still subject to normal
dependency checks.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The restart check whether new symbols became visible, didn't always work for
choice symbols. Even if a choice symbol itself isn't changable, the childs
are. This also requires to update the new status of all choice values, once
one of them is set.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When doing its recursive dependency check, scripts/kconfig/conf uses the flag
SYMBOL_CHECK_DONE to avoid rechecking a symbol it has already checked.
However, that flag is only set at the top level, so if a symbol is first
encountered as a dependency of another symbol it will be rechecked every time
it is encountered until it's encountered at the top level.
This patch adjusts the flag setting so that each symbol will only be checked
once, regardless of whether it is first encountered at the top level, or while
recursing down from another symbol. On complex configurations, this vastly
speeds up scripts/kconfig/conf. The config in the powerpc merge tree is
particularly bad: this patch reduces the time for 'scripts/kconfig/conf -o
arch/powerpc/Kconfig' by a factor of 40 on a G5. That's even including the
time to print the config, so the speedup in the actual checking is more likely
2 or 3 orders of magnitude.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch schedules obsolete OSS drivers (with ALSA drivers that support
the same hardware) for removal.
Scheduling the via82cxxx driver for removal was ACK'ed by Jeff Garzik.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Evgeny Stambulchik found that doing the following always worked:
# mount /dev/fd0 /mnt/floppy/
mount: block device /dev/fd0 is write-protected, mounting read-only
# mount -o remount,rw /mnt/floppy
# echo $?
0
This is the case because the block device /dev/fd0 is writeable but the
floppy disk is marked protected. A fix is to simply have floppy_open mark
the underlying gendisk policy according to reality (since the VFS doesn't
provide a way for do_remount_sb to inquire as to the current device
status).
Signed-off-by: Jon Masters <jcm@jonmasters.org>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes only the functions in swsusp.c call functions in snapshot.c
and not both ways. It also moves the check for available swap out of
swsusp_suspend() which is necessary for separating the swap-handling functions
in swsusp from the core code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch simplifies the relocation of the page backup list (aka pagedir)
during resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The changes made by this patch are necessary for the pagedir relocation
simplification in the next patch. Additionally, these changes allow us to
drop check_pagedir() and make get_safe_page() be a one-line wrapper around
alloc_image_page() (get_safe_page() goes to snapshot.c, because
alloc_image_page() is static and it does not make sense to export it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MPC834x uses the gianfar network driver which now uses the new phylib. We
need to update the platform code to create a gianfar platform MDIO bus and
pass the right intializations to the gianfar driver to make things work
again.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A non-broken udev would autoload also the drivers for devices on the
pseries vio bus, like ibmveth, ibmvscsic and hvsc. This is similar to pci,
usb and ieee1394:
/lib/modules/`uname -r`/modules.alias
alias vio:TvscsiSIBM,v-scsi* ibmvscsic
alias vio:TnetworkSIBM,l-lan* ibmveth
alias vio:Tserial-serverShvterm2* hvcs
/events/debug.00004.pci.add.1394:MODALIAS='pci:v00001014d00000188sv00000000sd00000000bc06sc04i0f'
/events/debug.00005.pci.add.1509:MODALIAS='pci:v00008086d00001229sv00001014sd000001FFbc02sc00i00'
/events/debug.00026.vio.add.1519:MODALIAS='vio:TserialShvterm1'
/events/debug.00027.vio.add.1446:MODALIAS='vio:TvscsiSIBM,v-scsi'
/events/debug.00028.vio.add.1451:MODALIAS='vio:TnetworkSIBM,l-lan'
modprobe -v vio:TnetworkSIBM,l-lan
insmod /lib/modules/2.6.14-20051030_vio-ppc64/kernel/drivers/net/ibmveth.ko
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes mismerged Makefile that prevented the ppc85xx rapidio support from being
built.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch extends the selinuxfs context interface to allow return the
canonical form of the context to userspace.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch disables the setting of SELinux xattrs on files created in
filesystems labeled via mountpoint labeling (mounted with the context=
option). selinux_inode_setxattr already prevents explicit setxattr from
userspace on such filesystems, so this provides consistent behavior for
file creation.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch enables files created on a MLS-enabled SELinux system to be
accessible on a non-MLS SELinux system, by skipping the MLS component of
the security context in the non-MLS case.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the PCIGART increment and add a cpu_to_le32 for ppc (untested)
Paulus was unsure if we need to cpu_to_le32 but the old code was definitely
wrong, so make it consistent and let the PPC guys figure it out later.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If ACPI sleep is not configured, but someone still wants to run swsusp,
he'd get oops in enter_state. This is regression since 2.6.14 and this
fixes it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/onenand/onenand_base.c: In function `onenand_wait':
drivers/mtd/onenand/onenand_base.c:293: error: `jiffies' undeclared (first use in this function)
drivers/mtd/onenand/onenand_base.c:293: error: (Each undeclared identifier is reported only once
drivers/mtd/onenand/onenand_base.c:293: error: for each function it appears in.)
drivers/mtd/onenand/onenand_base.c:293: error: implicit declaration of function `msecs_to_jiffies'
drivers/mtd/onenand/onenand_base.c:294: error: implicit declaration of function `time_before'
drivers/mtd/onenand/onenand_base.c:301: error: implicit declaration of function `cond_resched'
drivers/mtd/onenand/onenand_base.c: In function `onenand_get_device':
drivers/mtd/onenand/onenand_base.c:522: error: implicit declaration of function `set_current_state'
drivers/mtd/onenand/onenand_base.c:522: error: `TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/mtd/onenand/onenand_base.c:525: error: implicit declaration of function `schedule'
drivers/mtd/onenand/onenand_base.c: In function `onenand_release_device':
drivers/mtd/onenand/onenand_base.c:545: error: `TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/mtd/onenand/onenand_base.c:545: error: `TASK_INTERRUPTIBLE' undeclared (first use in this function)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/rfd_ftl.c: In function `find_free_block':
drivers/mtd/rfd_ftl.c:528: error: `jiffies' undeclared (first use in this function)
drivers/mtd/rfd_ftl.c:528: error: (Each undeclared identifier is reported only once
drivers/mtd/rfd_ftl.c:528: error: for each function it appears in.)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sound/drivers/vx/vx_hwdep.c: In function `free_fw':
sound/drivers/vx/vx_hwdep.c:144: error: implicit declaration of function `vfree'
sound/drivers/vx/vx_hwdep.c: In function `vx_hwdep_dsp_load':
sound/drivers/vx/vx_hwdep.c:163: error: implicit declaration of function `vmalloc'
Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On a large SMP box we get a lot of softlockup thread XX started lines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When calling target drivers to set frequency, we take cpucontrol lock.
When we modified the code to accomodate CPU hotplug, there was an attempt
to take a double lock of cpucontrol leading to a deadlock. Since the
current thread context is already holding the cpucontrol lock, we dont need
to make another attempt to acquire it.
Now we leave a trace in current->flags indicating current thread already is
under cpucontrol lock held, so we dont attempt to do this another time.
Thanks to Andrew Morton for the beating:-)
From: Brice Goglin <Brice.Goglin@ens-lyon.org>
Build fix
(akpm: this patch is still unpleasant. Ashok continues to look for a cleaner
solution, doesn't he? ;))
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Kyungmin Park
This patch is required for OneNAND MTD to passing the OneNAND sync. burst read
Signed-off-by: Kyungmin Park
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
save_and_disable_irqs does not need to use mov + msr (which was
introduced to work around a documentation bug which was propagated
into binutils.) Use msr with an immediate constant, and if we're
building for ARMv6 or later, use the new CPSID instruction.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sd_issue_flush() is called from atomic context so we can't use the
semaphore based routines to get a reference to the scsi_disk. Assume
something else already got the reference so we can safely use it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Ben Dooks
Fix the map_desc initialisers for the SMDK2440 machine
to use the new .pfn method, and at the same time making
the differntiation between ISA IO and Memory space
accesses
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Change the initialiser for the map_desc for the
iPAQ RX3715 to use the new pfn initialiser, and
also reduce the amount of ISA space mapped (we
only need to stop any ISA IO writes OOPsing
the system, so do not need >1Mbyte of space)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the map_desc initialisers for the Simtec Anubis
board to match the new initialiser scheme.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes compiler warnings when CONFIG_ISA and CONFIG_PCI are not
enabled in the dgrc network driver.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- if condition fix for ata_dev_identify()
- ata_pio_poll() minor cleanup.
Changes:
- Use (dev->class == ATA_DEV_ATA) for ata_dev_identify()
since "qc->tf.command" has been overwritten by the device status
- Use HSM_ST_TMOUT directly in ata_pio_poll()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If the driver ever wants to add ethtool support it should use
ethtool_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Usual fix:
- b44_interrupt() does not schedule NAPI polling when the device is
going down;
- b44_close() waits for any scheduled NAPI polling before it starts
to release the private structures of the device.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Increase the driver version number and print version when
probing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use prefetch() in the interrupt path to try and look ahead
at the next place will be looking at in the ring.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When skge is booted up, the PHY may be stuck in power down state
by the previous OS. So we may need to turn it on.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
You could open the /proc/sys/net/ipv4/conf/<if>/<whatever> file, then
wait for interface to go away, try to grab as much memory as possible in
hope to hit the (kfreed) ctl_table. Then fill it with pointers to your
function. Then do read from file you've opened and if you are lucky,
you'll get it called as ->proc_handler() in kernel mode.
So this is at least an Oops and possibly more. It does depend on an
interface going away though, so less of a security risk than it would
otherwise be.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the support for the 16550 present on most IOC3 configurations to use
the current API.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Make it completely deterministic and leave nothing to chance
(even if it had at worst 0.001% probability of failing).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Force a watchdog reset if the system fails to
decompress properly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/char/agp/i460-agp.c: In function `i460_fetch_size':
drivers/char/agp/i460-agp.c:115: warning: size_t format, long unsigned int arg (arg 2)
drivers/char/agp/i460-agp.c:115: warning: size_t format, long unsigned int arg (arg 3)
drivers/char/agp/i460-agp.c: In function `i460_mask_memory':
drivers/char/agp/i460-agp.c:542: warning: integer constant is too large for "long" type
Note that the i460_mask_memory() change is a guess. But a good one, I suspect.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
AGP allocation/deallocation is suffering major performance issues due to
the nature of global_flush_tlb() being called on every change_page_attr()
call.
For small allocations this isn't really seen, but when you start allocating
50000 pages of AGP space, for say, texture memory, then things can take
seconds to complete.
In some cases the situation is doubled or even quadrupled in the time due
to SMP, or a deallocation, then a new reallocation. I've had a case of
upto 20 seconds wait time to deallocate and reallocate AGP space.
This patch fixes the problem by making it the caller's responsibility to
call global_flush_tlb(), and so removes it from every instance of mapping a
page into AGP space until the time that all change_page_attr() changes are
done.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The problem is that scsi_run_queue is called from scsi_next_command()
after doing a scsi_put_command. If the command was the only thing
holding the reference on the scsi_device then the resulting device put
will tear down the block queue. Fix this by taking a reference to the
device and holding it around scsi_run_queue()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When non-leader thread does exec, de_thread calls release_task(leader) before
calling exit_itimers(). If local timer interrupt happens in between, it can
oops in send_group_sigqueue() while taking ->sighand->siglock == NULL.
However, we can't change send_group_sigqueue() to check p->signal != NULL,
because sys_timer_create() does get_task_struct() only in SIGEV_THREAD_ID
case. So it is possible that this task_struct was already freed and we can't
trust p->signal.
This patch changes de_thread() so that leader released after exit_itimers()
call.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Dirk Opfer
This patch updates the tosa machine to use the new SharpSL PCMCIA layer introduced with Patch #3093/1
Depends on #3093/1
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The Sharp SL-Cxx00 models have a combined power control for the SD
and CF slot 0. This patch adds hooks to the scoop driver to allow
machines to provide a custom control function for this and such a
function is added for spitz/akita/borzoi.
It also moves the gpio init code into the machine files as this
is machine dependent and differs between some models. A couple of
warnings when compiling for collie are also fixed.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the map_desc entries to use the new .pfn
initialiser for the Simtec BAST machine support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the initialisation of the map_desc fields
in the Thorcom VR1000 machine support to use
the new .pfn initialiser.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds MMC, IRDA and UDC support to the Sharp SL-6000x device. Also it adds a platform device for the keyboard driver.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add infrastructure for supporting per-cpu local timers to update
the profiling information and update system time accounting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ia64 translates normal loads and stores to special MMIO regions into I/O port
accesses. Reserve these special MMIO regions in /proc/iomem.
Sample /proc/iomem:
f8100000000-f81003fffff : PCI Bus 0000:80 I/O Ports 00000000-00000fff
f8100400000-f81007fffff : PCI Bus 0000:8e I/O Ports 00001000-00001fff
f8100800000-f8100ffffff : PCI Bus 0000:9c I/O Ports 00002000-00003fff
f8101000000-f81017fffff : PCI Bus 0000:aa I/O Ports 00004000-00005fff
and corresponding /proc/ioports:
00000000-00000fff : PCI Bus 0000:80
00001000-00001fff : PCI Bus 0000:8e
00002000-00003fff : PCI Bus 0000:9c
00004000-00005fff : PCI Bus 0000:aa
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When a page has a memory uncorrectable ECC error, the recovery
code wants to prevent the page from being reused. This change
bumps the reference count to prevent the page from getting back
on the free list.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
paddr needs to be shifted by PAGE_SHIFT to be valid
input for pfn_valid().
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The determination of whether an MCA is recoverable or not must
be based on the bits set in the PSP (Processor State Parameter).
The specific bits are shown in the Intel IA-64 Architecture Software
Developer's Manual, Vol 2, Table 11-6 Software Recovery Bits in
Processor State Parameter. Those bits should be consistent
across the entire IA-64 family of processors.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment on get_user_insn to the more general "pte lock", which may
or may not be the page_table_lock. Note vmtruncate handled like kswapd.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, attempting to invoke a signal-handler on the normal
stack is guaranteed to fail if the stack-pointer happens not to be
16-byte aligned. This is because the signal-trampoline will attempt
to store fp-regs with stf.spill instructions, which will trap for
misaligned addresses. This isn't terribly useful behavior. It's
better to just always align the signal frame to the next lower 16-byte
boundary.
Signed-off-by: David Mosberger-Tang <David.Mosberger@acm.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes all relics of the /proc usage from the Bluetooth
subsystem core and its upper layers. All the previous information are
now available via /sys/class/bluetooth through appropriate functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the endian annotations to the Bluetooth core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the module parameter ignore_dga to the HCI USB driver
which makes it possible to prevent this driver from being loaded by
some buggy Digianswer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original memory less node allocation attempted to use NODEDATA_ALIGN for
alignment. The bootmem allocator only allows a power of two alignments. This
causes a BUG_ON for some nodes. For cpu only nodes just allocate with a
PERCPU_PAGE_SIZE alignment.
Some older firmware reports SLIT distances of 0xff and results in bestnode
not being computed. This is now treated correctly.
The failed allocation check was removed because it's redundant. The
bootmem allocator already makes this check.
This fix has been boot tested on 4 node machine which has 4 cpu only nodes
and 1 memory node. Thanks to Pete Keilty for reporting this and helping me
test it.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When ip_queue_xmit calls ip_select_ident_more for IP identity selection
it gives it the wrong packet count for TSO packets. The ip_select_*
functions expect one less than the number of packets, so we need to
subtract one for TSO packets.
This bug was diagnosed and fixed by Tom Young.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Domsch <Matt_Domsch@dell.com>
The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor. This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.
This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.
Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).
Feedback to <pptpclient-devel@lists.sourceforge.net> please.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: "Philippe De Muyter" <phdm@macqel.be>
This patch avoids ppp-generated kernel crashes on machines where unaligned
accesses are forbidden (ie: m68000), by fixing ppp alignment setting for
reused skb's.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a fix in 2.6.13 that changed the behaviour of
ip_vs_conn_expire_now function not to put reference to connection,
its callers should hold write lock or connection refcnt. But we
forgot to convert one caller, when the real server for connection
is unavailable caller should put the connection reference. It
happens only when sysctl var expire_nodest_conn is set to 1 and
such connections never expire. Thanks to Roberto Nibali who found
the problem and tested a 2.4.32-rc2 patch, which is equal to this
2.6 version. Patch for 2.4 is already sent to Marcelo.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Roberto Nibali <ratz@drugphish.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for sk_add_backlog to be a macro. It can
just be an inline function and get type checking.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes an invalid memory reference when the basic classifier
is used without any ematches but just actions.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Carlo Comin <vl4d spine-group.org>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose more appropriate source address; e.g.
- outgoing interface
- non-deprecated
- scope
- matching label
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch encloses the idr.h header file in
#ifndef __IDR_H__ macro.
Signed-off-by: Luben Tuikov <luben_tuikov@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
If anyone needs a fully-functional befs driver, the easiest route to
that would probably be getting Haiku's befs driver to compile in
userland as a FUSE fs.
At any rate, attribute.c can go. It is easy enough to add back in if
anyone ever wants to do the (relativly minor) refactoring nessisary to
get it working.
Signed-off-by: Will Dyson <will.dyson@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
arch/arm/kernel/irq.c:998:26: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:145:25: warning: Using plain integer as NULL pointer
arch/arm/kernel/smp.c:362:5: warning: symbol 'smp_call_function_on_cpu' was not declared. Should it be static?
drivers/video/amba-clcd.c:521:12: warning: symbol 'amba_clcdfb_init' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This factors out the common bits of arch/powerpc/xmon/start_*.c into
a new nonstdio.c, and removes some stuff that was supposed to make
xmon's I/O routines somewhat stdio-like but was never used.
It also makes the parsing of the xmon= command line option common,
so that ppc32 can now use xmon={off,on,early} also.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some powermac machines were crashing in the quiesce firmware call
in prom_init.c because we have just closed the OF stdin device;
notably my 1999 G3 powerbook does this. To avoid this, don't
close the OF stdin device on powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Until we have local timer support, we need to broadcast the
timer interrupt to the other CPUs. Also, add the missing
smp_send_timer() prototype to asm/smp.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The big i2c-viapro SMBus driver update which went into 2.6.14-git1
introduced a few minor issues. Nothing critical, but I would like a
few adjustments to be merged in to fix the following problems:
* VIA should not be spelled Via.
* Frodo Looijaard and Philip Edelbrock did not write the i2c-viapro
driver.
* When debugging is disabled, half of messages would be logged.
* Drop an unneeded masking.
* Some port reads can be avoided now that the transaction size is
passed as a parameter to vt596_transaction().
* SMBus Receive Byte transactions are used for probing too (for
EEPROMs), so hide errors on these too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Fix in4 reads for W83627THF and W83637HF chips.
* Use the correct register for alarm flags.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix BCD value errors when month=9, moving the increment inside the
BIN2BCD macro.
Fix similar code for the weekday value, just for consistency.
This bug was reported by Michael Burian <dynmail1@gassner-waagen.at>.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My latest update to the writing-clients i2c documentation file was
incomplete, here's the complement.
Large parts of this file are still way out-of-date, but at least now
the memory allocation and freeing instructions are consistent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ppc64 needs a special sysfs probe file for adding new memory.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a temporary kludge that supports adding all new memory to
node 0. I will provide a more complete solution similar to that
used for dynamically added CPUs in a few days.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
memmap_init_zone() sets page count to 1. Before 'freeing' the
page, we need to clear the count. This is the same that is done
on free_all_bootmem_core() for memory discovered at boot time.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the create_section_mapping() routine to create hptes for memory
sections dynamically added after system boot.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More conversions of kmalloc/memset to kzalloc
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify the correct range when calling memset in atmel_get_range.
Do this by specifying the size of the structure, rather than the size
of the pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch below fixes the following sparse warnings:
drivers/net/e100.c:1481:13: warning: Using plain integer as NULL pointer
drivers/net/e100.c:1767:27: warning: Using plain integer as NULL pointer
drivers/net/e100.c:1847:27: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move update of the transmit statistics to the correct place. This
would be just before starting transmission rather than (potentially
long) afterward.
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In isl_38xx.c :
The variable "counter" is defined and incremented but never
used except if the driver is hand-compiled setting
VERBOSE > SHOW_ERROR_MESSAGES.
Move the definition and the increment to within the
#if VERBOSE .. block.
Remove extraneous udelay's.
These are not required when triggering the device.
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch kills include/linux/eeprom.h .
Rationale:
- it was only used by one single driver
- even this driver didn't do anything useful with it
- most of this file are non-inline and non-static functions (sic)
This removes include/linux/eeprom.h and cleans drivers/net/ns83820.c up.
If you think eeprom.h should be used more extensively, please consider:
- the code has to be moved from the header file to a .c file
- the currently empty write function has to be implemented
- ns83820.c or any other driver should actually use it
Noone did any of these during the more than 3 years eeprom.h already
exists...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should resolve http://bugzilla.kernel.org/show_bug.cgi?id=5519
The current feature computation loses bits that it doesn't know about,
resulting in an inability to add VLANs and possibly other havoc.
Rewrote function to preserve bits it doesn't know about, remove an
unneeded state variable, and simplify the code.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following compile error with CONFIG_NET_RADIO=n and
CONFIG_IEEE80211=y:
LD .tmp_vmlinux1
net/built-in.o: In function `ieee80211_rx':
: undefined reference to `wireless_spy_update'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An unbindable mount does not forward or receive propagation. Also
unbindable mount disallows bind mounts. The semantics is as follows.
Bind semantics:
It is invalid to bind mount an unbindable mount.
Move semantics:
It is invalid to move an unbindable mount under shared mount.
Clone-namespace semantics:
If a mount is unbindable in the parent namespace, the corresponding
cloned mount in the child namespace becomes unbindable too. Note:
there is subtle difference, unbindable mounts cannot be bind mounted
but can be cloned during clone-namespace.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes bind, rbind, move, clone namespace and umount operations
aware of the semantics of slave mount (see Documentation/sharedsubtree.txt
in the last patch of the series for detailed description).
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A slave mount always has a master mount from which it receives
mount/umount events. Unlike shared mount the event propagation does not
flow from the slave mount to the master.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An unmount of a mount creates a umount event on the parent. If the
parent is a shared mount, it gets propagated to all mounts in the peer
group.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement handling of mount --move in presense of shared mounts (see
Documentation/sharedsubtree.txt in the end of patch series for detailed
description).
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement handling of MS_BIND in presense of shared mounts (see
Documentation/sharedsubtree.txt in the end of patch series for detailed
description).
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This creates shared mounts. A shared mount when bind-mounted to some
mountpoint, propagates mount/umount events to each other. All the
shared mounts that propagate events to each other belong to the same
peer-group.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A private mount does not forward or receive propagation. This patch
provides user the ability to convert any mount to private.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes the per-namespace semaphore in favor of a global semaphore.
This can have an effect on namespace scalability.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- clean up the ugliness in may_umount_tree()
- fix a bug in do_loopback(). after cloning a tree, do_loopback()
unlinks only the topmost mount of the cloned tree, leaving behind the
children mounts on their corresponding expiry list.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
umount is done under the protection of the namespace semaphore. This
can lead to intresting deadlocks when the last reference to a mount is
released, if filesystem code is in sufficiently nasty state.
This collects all the to-be-released-mounts and releases them after
releasing the namespace semaphore. That both reduces the time we are
holding namespace semaphore and gets the things more robust.
Idea proposed by Al Viro.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Old semantics: graft_tree() grabs a reference on the vfsmount before
returning success.
New one: graft_tree() leaves that to caller.
All the callers of graft_tree() immediately dropped that reference
anyway. Changing the interface takes care of this unnecessary overhead.
Idea proposed by Al Viro.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow caller of seq_open() to kmalloc() seq_file + whatever else they
want and set ->private_data to it. seq_open() will then abstain from
doing allocation itself.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- check_mnt() on the source of binding should've been unconditional
from the very beginning. My fault - as far I could've trace it,
that's an old thinko made back in 2001. Kudos to Miklos for spotting
it...
Fixed.
- code cleaned up.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The way we currently deal with quota and process accounting that might
keep vfsmount busy at umount time is inherently broken; we try to turn
them off just in case (not quite correctly, at that) and
a) pray umount doesn't fail (otherwise they'll stay turned off)
b) pray nobody doesn anything funny just as we turn quota off
Moreover, LSM provides hooks for doing the same sort of broken logics.
The proper way to deal with that is to introduce the second kind of
reference to vfsmount. Semantics:
- when the last normal reference is dropped, all special ones are
converted to normal ones and if there had been any, cleanup is done.
- normal reference can be cloned into a special one
- special reference can be converted to normal one; that's a no-op if
we'd already passed the point of no return (i.e. mntput() had
converted special references to normal and started cleanup).
The way it works: e.g. starting process accounting converts the vfsmount
reference pinned by the opened file into special one and turns it back
to normal when it gets shut down; acct_auto_close() is done when no
normal references are left. That way it does *not* obstruct umount(2)
and it silently gets turned off when the last normal reference to
vfsmount is gone. Which is exactly what we want...
The same should be done by LSM module that holds some internal
references to vfsmount and wants to shut them down on umount - it should
make them special and security_sb_umount_close() will be called exactly
when the last normal reference to vfsmount is gone.
quota handling is even simpler - we don't use normal file IO anymore, so
there's no need to hold vfsmounts at all. DQUOT_OFF() is done from
deactivate_super(), where it really belongs.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For some stupid reason I can't explain (brown paper bag is at hand), I
removed the check pfn_valid() in the code that does the icache/dcache
coherency on POWER4 and later. That causes us to eventually try to
access non existing struct page when hashing in IO pages.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is very simple with it being almost all ppc32 with just a couple
of common defines.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, Nov 08, 2005 at 08:12:56AM +1100, Benjamin Herrenschmidt wrote:
> Yes, the MAX_ORDER should be different indeed. But can Kconfig do that ?
> That is have the default value be different based on a Kconfig option ?
> I don't see that ... We may have to do things differently here...
This seems to be done in other parts of the Kconfig file. Using those
as an example, this should keep the MAX_ORDER block size at 16MB.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Even though we can enable and disable xmon at runtime now, there are a
few places in the merge tree that call xmon and xmon_printf directly.
In the case below we call die() which will call xmon if it is enabled.
Also remove an unnecessary include of xmon.h in smp.c.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oprofile was hardwiring the MMCRA sample bit to 1 but on newer cpus
(eg POWER5) we want to vary it based on the group being sampled.
Add a temporary workaround until people update their oprofile userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 we end up with a negative value for the data size in the memory
boot message:
Memory: 2035560k/2097152k available (5792k kernel code, 89564k reserved,
18014398509481632k data, 870k bss, 352k init)
It turns out the section ordering of the linker script is different on
ppc32 and ppc64, so just count data as _edata - _sdata which should work
on both.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PowerBook HD led code uses obsoletes device-tree accessors which do
not work anymore for getting the root of the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon() prototype is inconsistent between ARCH=ppc and ARCH=powerpc,
thus causing ARCH=ppc build breakage.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building a PowerMac kernel with ARCH=powerpc causes a bunch of warnings,
this fixes some of them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a new thermal control framework for PowerMac, along with the
implementation for PowerMac8,1, PowerMac8,2 (iMac G5 rev 1 and 2), and
PowerMac9,1 (latest single CPU desktop). In the future, I expect to move
the older G5 thermal control to the new framework as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some more U3 revisions have the missing "interrupts" property in U3,
this adds them to the fixup code in prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates g5_defconfig for ARCH=powerpc in order to add the SMU
support & thermal drivers to it, the pmac sound driver (works on some
G5s) and replaces rivafb with nvidiafb which works better for the cards
found in G5 based machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the ability to the SMU driver to recover missing
calibration partitions from the SMU chip itself. It also adds some
dynamic mecanism to /proc/device-tree so that new properties are visible
to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
CPU freq support using 970FX powertune facility for iMac G5 and SMU
based single CPU desktop.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
OK, the Fedora ppc32 and ppc64 kernels should both be arch/powerpc by
tomorrow. They're booting on G5, POWER5, and my powerbook. I'll test
pmac SMP and Pegasos later -- but pmac smp is known broken in arch/ppc
anyway, and I'll live with a potential Pegasos regression for now; it
wasn't supported officially in FC4 either.
I needed to fix ppc32 initrd -- we were never setting initrd_start.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
configured.
Countermeasures default to being turned off when wpa_supplicant runs,
regardless of if TKIP is being used. They are only turned on if a TKIP
is running. The warning we were printing is therefore not needed.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The problem is caused by the patch in bug455 -- Channel change flood
generates fatal error.
The patch set the DISASSOCIATING status bit after sending the command.
The process was scheduled out when waiting for the command to be sent to
the card. The disassociated notification clears the DISASSOCIATING bit
in the tasklet before the process set the bit.
Move the bit setting code before sending the command now.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The PF_SYNCTHREAD check was introduced to try and remain compatible with
SWSUSP2. This check is no longer needed with newer versions.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
error when it tries to auth to a WPA ap. The patch filters out WPA
networks if the card is not wpa enabled when selecting network to
associate to.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Because of the frequent channel change, it is possible that when we are
try to associate with channel 1 (authenticated but not associated).
Another channel change comes at this time, then the driver will issue
disassociate command to the firmware which will cause the fatal error.
It seems that the association/disassociation procedure should not be
interrupted.
The patch attached adds test on STATUS_ASSOCIATING | STATUS_DISASSOCIATING
in ipw_send_cmd(), when ensures that commands will not be sent to firmware
when we are in these two status.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
(handle_probe_response, handle_beacon, handle_association_response).
Fixed a problem with ipw_send_cmd() returning non-zero on success.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
You can now specify via the module parameter 'cmdlog' to allocate a
ring buffer for caching host commands sent to the firmware. They can
then be dumped at any time via the sysfs entry 'cmd_log'
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
codes to the caller and changed ipw_send_cmd itself to print the error
message to the syslog indicating which command failed to be sent.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
via sysfs even if debugging disabled. When a firmware error is
captured, it will be dumped to the kernel log (if debug enabled) and
captured in memory to be retrieved via sysfs.
If an error has already been captured, subsequent errors will be
dropped.
The existing error can be cleared by writing to the error log entry.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
with request_scan being called before initialized if invoked from
insmod, resulting in no association occurring during boot until iwlist
scan is run.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
If we configure the wep keys after creating the ibss network, the
beacons of this network will not show correctly (it still shows "key
off" in iwlist scan report). This is because we don't update the
beacon info in firmware.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
iwconfig matches what their hardware can actually do in regard to
supported channel maps, etc.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
We send SYSTEM_CONFIG command after the TGI_KEY command if hardware
encryption is enabled. It sometimes causes a firmware stall (firmware
doesn't respond to any request) and finally bungs up the Tx send queue.
The solution is to send SYSTEM_CONFIG command in the post association
stage from a workqueue.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#452 problem with setting retry limit (thanks to Hong Liu)
* Fixed#592 race condition during association causing firmware errors
* Fixed#602 problem with building in 64-bit environment
* Fixed#625 problem with SCAN_REQUEST_EXT sometimes failing
* Fixed#645 problem with bit rate not decreasing when moving laptop
farther from AP
* Fixed#656 problem with 'iwconfig eth1 mode auto' and 'modprobe'
locking the system
* Fixed#667 problem with "No space for Tx" for hwcrypto=1
* Fixed#685 kernel panic in rmmod caused by led work is still queued
* Fixed#695 problem with network doesn't reassociate after suspend/resume
* Fixed#701 problem with 'iwprvi sw_reset' not resetting the card from
monitor mode
* Fixed#710 problem with monitor mode being used after a WEP key has
been configured
* Fixed network->mode vs. priv->ieee->iw_mode checking (thanks to Ben Cahill)
* Fixed "Unknown management packet %d" warning
* Fixed setting channels multiple times in monitor mode causes scan stopped
* Fixed ipw_wx_sw_reset doesn't switch firmware if mode is changed.
* Add duplicate packet checking code (kill ping DUP! and TKIP replay warning)
* Fix hardware encryption (both WEP and AES) doesn't work with fragmentation.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
support wpa_supplicant with open AP. We need this to make driver_ipw
work.
driver_ext has already had the similar code with the WE-18 support
added.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Added WE-18 support. This allows the use of -Dext with wpa_supplicant
> 0.4.x (thanks to Hong Liu)
* Fixed#339 problem with iwconfig set/get txpower (thanks to Hong Liu)
* Fixed#598 problem when with error messages when module loaded with
'disable=1' (thanks to Hong Liu)
* Fixed#640 problem with 'iwlist retry' now showing min/max retry
* Fixed compatibility with wpa_supplicant and the new -Dipw interface
(that included a fix for 64-bit compatibility)
* Added CFG_CRC_CHECK which allows passing through packets with bad
CRCs while in monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#627 problem with open APs not working with wpa_supplicant
* Fixed#632 problem with 'txpower auto' setting power incorrectly (thanks
to Kai Groner)
* Fixed#634 problem with 'iwconfig eth1 frag 0' hanging the shell
* Fixed problem with adapter not fully powering off during suspend to RAM or
when module unloaded.
* Fixed#645 problem with turning fixed rates off not taking effect until
you reload the driver
* Fixed problem with firmware restart if wpa_supplicant was used to set a key
that wasn't exactly 5 or 13 bytes in length.
* Fixed#623 Added iwpriv sw_reset extension to reset sw parameters
* Added managment frame export to user space with frame statistics
* Fixed#652 Modified the driver to load the EEPROM data even if RF KILL is
active during driver load
* Global s:CX2_:IPW_:g to make code more consistent
* Fixed#572 problem with setting txpower to auto
* Fixed#656 problem with kernel oops if mode auto; modprobe -r ipw2200
* Added QoS (CONFIG_IPW_QOS) support. This is being actively developed but
is the first step in getting WMM support into the driver and the kernel.
* Fixed some race conditions with channel changes, association, and scan
abort that could periodically cause a firmware restart.
* Added some extensions to export scan and network statistics to user space
(exposed through speed_scan and net_stats sysfs entries)
* Fixed a few bugs in how monitor mode was supported (scan lists
weren't quite right)
* Updated the firmware requirement from 2.2 to 2.3 which supports
monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fix#616 problem with OOPS on module load (thanks to Yi Zhu)
* Fixed problem with led module parameter being described as
'auto_create'
* Added support to merge between adhoc networks (thanks to Mohamed Abbas)
* Added semaphore lock at the driver's entry points to protect against
re-entry (thanks to Mohamed Abbas)
* Added semaphore lock to background scheduled driver actions (thanks to
Mohamed Abbas)
* Changed how signal quality is reported for scan output (thanks to
Peter Jones)
* Fixed how high/low clamp values of signal quality are reported so a
more consistent ramp is provided (thanks to Bill Moss)
* Fix#624 problem with duplicate addresses (again) (thanks to Bernard
Blackham)
* Fix#385 problem with fragmentation and certain sized packets (thanks
to Mohamed Abbas)
* Modified iwconfig network name if RF kill is enabled to say 'radio off'
* Fix#382 problem with driver not responding to probe requests in Ad-Hoc
mode (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Removed unneeded parenthesis around numeric constant defines
Added support for iwspy
Put in fix for Ad-Hoc mode not passing through all packets (thanks to KKH)
Put in fix for fragmentation not working for fragment sizes between
441-464 bytes (thanks to Mohamed Abbas)
Fixed#592 problem of CONFIG_IEEE80211_WPA_MODULE not including WPA
support into the driver -- fixed as a result of no longer limiting WPAs
inclusion
Fixed#594 problem with user rates mask causing lack of association if
AP mandatory rate is masked out. We now add back in as a supported rate
any mandatory rate.
Fixed#597 kernel oops due to calling dev_kfree_skb on an skb multiple times.
Added code to control LEDs that can be controlled through the wireless
NIC (vs. non-wireless HW interfaces) -- this is currently disabled by
default due to reports by some users of it hanging their laptop.
Added some more debug messages around fragmentation logic
Added locking around STATUS_HCMD_ACTIVE to prevent re-entry race
conditions
Moved ipw_adapter_restart to only execute on the priv->workqueue to
keep keyboard errors from occuring during adapter restart
Added CFG_BACKGROUND_SCAN to easily allow people to play with
background scanning implementations
Modified WPA logic to send WPA IE if one is set (vs. being based on
wpa_enabled)
Modified scan result logic to report WPA and RSN IEs if set (vs. being
based on wpa_enabled)
Fixed issues with endianess compatability between the host and
wireless adapter (thanks to York Liu and Yi Zhu)
Fixed problem with Ad-Hoc network creation causing a firmware error if
a scan was actively running (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This commit contains the following fixes:
Fixed#559: iwconfig rate support (thanks to Florian Hackenberger)
Improved link signal quality calculation (thanks to Bill Moss)
Fixed a problem with sensitivity threshold during association
Added iwpriv for turning forcing long preamble support:
% iwpriv eth1 set_preamble 1|0
Fixed#542 and #377 support for short preamble
Fixed locked BSSID reporting channel number (thanks to Pedro
Ramalhais)
Fixed type-o with scan watchdog timeout message (thanks to Pedro
Ramalhais)
Changed logic for displaying get_mode output so the code is easier to
follow (thanks to Pedro Ramalhais)
Added initial support for WPA (thanks to Yi Zhu) -- tested with
wpa_supplicant (either tip w/ ipw driver, or with -Dipw2100) with
both CCMP and TKIP
Fixed problem with CCMP not working due to uninitialized 802.11
header fields (thanks to Pedro Ramalhais)
Bug references are to defects stored on http://bughost.org
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The functions ieee80211_wx_{get,set}_encodeext fail if one tries to set
unicast (IW_ENCODE_EXT_GROUP_KEY not set) keys at key indices>0. But at
least some Cisco APs dish out dynamic WEP unicast keys at index !=0.
Signed-off-by: Volker Braun <volker.braun@physik.hu-berlin.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
drivers/drm/ now implements proper ->compat_ioctl methods, so this isn't
needed anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all ioctls are 32bit compat clean, so the driver can use ->compat_ioctl
and ->unlocked_ioctl easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
implement a compat_ioctl handle in the driver instead of having table
entries in sparc64 ioctl32.c (I plan to get rid of the arch ioctl32.c
file eventually)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all the ioctls in the driver are 32bit compat clean and don't need BKL,
so we can switch it to ->unlocked_ioctl and ->compat_ioctl trivially.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Would you mind applying the following patch that kills those two + the
m68k and Documentation/ references?
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor simplification to the sparc64 tlb_flush_mmu: tlb_remove_page
set need_flush only after handling the tlb_fast_mode case, then
tlb_flush_mmu need not consider whether it's tlb_fast_mode.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
all these are handled by fs/compat_ioctls.c already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know if we ever implemented this, but the only user in any 2.6
tree are the compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old keyboard driver is gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old sound drivers are gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this inline routine in arch/sparc64/kernel/ioctl32.c is completely
unused and superceeded by compat_alloc_user_space()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIOCPKT_ macros are defined by all other architectures in asm/ioctls.h
and so does sparc and sparc64, so reomve the duplicates in asm/termios.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It only serves to generate false-positive buildcheck warnings.
Just set it initially to tick_operations which uses the v9
%tick register which every sparc64 processor has.
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't needed any longer, as noted by Hugh Dickins.
We still need the flush routines, due to the one remaining
call site in hugetlb_prefault_arch_hook(). That can be
eliminated at some later point, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 is unique among architectures in taking the page_table_lock in
its context switch (well, cris does too, but erroneously, and it's not
yet SMP anyway).
This seems to be a private affair between switch_mm and activate_mm,
using page_table_lock as a per-mm lock, without any relation to its uses
elsewhere. That's fine, but comment it as such; and unlock sooner in
switch_mm, more like in activate_mm (preemption is disabled here).
There is a block of "if (0)"ed code in smp_flush_tlb_pending which would
have liked to rely on the page_table_lock, in switch_mm and elsewhere;
but its comment explains how dup_mmap's flush_tlb_mm defeated it. And
though that could have been changed at any time over the past few years,
now the chance vanishes as we push the page_table_lock downwards, and
perhaps split it per page table page. Just delete that block of code.
Which leaves the mysterious spin_unlock_wait(&oldmm->page_table_lock)
in kernel/fork.c copy_mm. Textual analysis (supported by Nick Piggin)
suggests that the comment was written by DaveM, and that it relates to
the defeated approach in the sparc64 smp_flush_tlb_pending. Just delete
this block too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 prom_callback and new_setup_frame32 each operates on a user page
table without holding lock, and no doubt they've good reason. But I'd
feel more confident if they were to do a "pte = *ptep" and then operate
on pte, rather than re-evaluating *ptep.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Georg Chini <georg.chini@triaton-webhosting.com>
Introduce some sbus_dma routines similar to the
ebus_dma stuff to make the code look nearly the same
for both cases.
Thanks to Christopher for testing.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a forward port of a 2.4.x sun4m LED driver written by Lars
Kotthoff.
Signed-off-by: Lars Kotthoff <metalhead@metalhead.ws>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Uli Luckas
This is a simplification of patch 3116/1 as sugested by Russell King.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Since we have to use XCB=101 instead of XCB=000 on the ixp2400 to
prevent it from regularly falling over, and since we have to deal with
manual write buffer flushing because of that, we might as well use
XCB=101 on all ixp2000 platforms since it's faster than XCB=000.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
nwfpe extended precision emulation used to be broken on big-endian
and was therefore disabled. This patch fixes nwfpe so that it copies
extended precision floats to/from userspace in the proper word order
(similar to patch #2046, see the description of that patch for an
explanation) and reenables the Kconfig option.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The routine that nwfpe uses for converting floats/doubles to
extended precision fails to zero two bytes of kernel stack. This
is not immediately obvious, as the floatx80 structure has 16 bits
of implicit padding (by design.) These two bytes are copied to
userspace when an stfe is emulated, causing a possible info leak.
Make the padding explicit and zero it out in the relevant places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
notify_die() added for MCA_{MONARCH,SLAVE,RENDEZVOUS}_{ENTER,PROCESS,LEAVE} and
INIT_{MONARCH,SLAVE}_{ENTER,PROCESS,LEAVE}. We need multiple
notification points for these events because they can take many seconds
to run which has nasty effects on the behaviour of the rest of the
system.
DIE_SS replaced by a generic DIE_FAULT which checks the vector number,
to allow interception of faults other than SS.
DIE_MACHINE_{HALT,RESTART} added to allow last minute close down
processing, especially when the halt/restart routines are called from
error handlers.
DIE_OOPS added.
The check for kprobe's break numbers has been moved from traps.c to
kprobes.c, allowing DIE_BREAK to be used for any additional break
numbers, i.e. it is no longer kprobes specific.
Hooks for kernel debuggers and kernel dumpers added, ENTER and LEAVE.
Both of these disable the system for long periods which impact on
watchdogs and heartbeat systems in general. More patches to come that
use these events to reset watchdogs and heartbeats.
unregister_die_notifier() added and both routines exported. Requested
by Dean Nelson.
Lock removed from {un,}register_die_notifier. notifier_chain_register()
already takes a lock. Also the generic notifier chain locking is being
reworked to distinguish between callbacks that can block and those that
cannot, the lock in {un,}register_die_notifier would interfere with
that change. http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
Leading white space removed from arch/ia64/kernel/kprobes.c.
Typo in mca.c in original version of this patch found & fixed by Dean
Nelson.
Signed-off-by: Keith Owens <kaos@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Acked-by: Anil Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add missing bits to fix D-cache aliasing problem in the PIO IDE driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 2.6.13-rc1 setup_frame and its variants return int. But some bits
were missed in the conversion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If HZ was 1000, mdelay(2) cause overflow on multiplication in
__udelay. We should define MAX_UDELAY_MS properly to prevent this.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Many RTC routines were not protected against each other, so there are
potential races, for example, ntp-update against /dev/rtc. This patch
fixes them using rtc_lock.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The mips_rtc_lock is no longer needed because RTC operations should be
protected already by other mechanism. (rtc_lock, local_irq_save, etc.)
Also, locking whole rtc_get_time/rtc_set_time should be avoided while
some RTC routines might take very long time (a few seconds).
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Switch to dynamic major
o Remove duplicate SHN_MIPS_SCOMMON definition
o Coding style: remove typedefs.
o Coding style: reorder to avoid the need for forward declarations
o Use kzalloc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move some of the m68knommu platform specific irq core support
to its own header, irqnode.h. Having it in asm-m68knommu/irq.h
causes some build pain, since it is included in a number of
common code places (and not all the required definitions will
be included at these places).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the new 5208 ColdFire (Matt Waddel / Mike Lavender)
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
I also re-ordered the init code to avoid interrupt lockups on
some platforms (at least the 5275, but others have reported it on
the 5235 as well).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the new 5208 ColdFire in the FEC ethernet header.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable the ColdFire 5249 cache support code - it should have been on.
Also one more change of "extern inline" to "static inline".
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support for the new Freescale 5208 ColdFire processor.
Also changed name "Motorola" to new company name "Freescale".
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the Freescale 5208 processor UART's to the common
ColdFire serial port code.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Align the param section. It can end up starting on an unalingned
boundary depending on the size of ksymtab_strings. If it is
unaligned things like modules will fail to load with unaligned
access traps.
Add linker scipt support for the M5208EVB board.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale M5208EVB ColdFire eval board is one of the few that
doesn't have its DRAM based at address 0. Handle this special case
in the common ColdFire startup code.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modified common ColdFire PIT timer code to support the 5208 as well.
It uses a different set of mask and interrupt bits than other ColdFire
processors. The defines for these bits have been moved in header
files and set appropriately for the different processor varients.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Platform configuration code for the Freescale 5208 ColdFire processor.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add build support for the new Freescale 5208 ColdFire processor,
and its M5208EVB eval board. Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale 5208 ColdFire uses the common PIT timer code for
its internal timer. Build it when configured for the 5208 processor.
Add support for the internal register map of the 5208 ColdFire fmaily.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add Freescale 5208 ColdFire platform Makefile.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add setup support for the new Freescale 5208 ColdFire processor.
(Also fixed a little typo in there, "UNKOWN" -> "UNKNOWN").
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Something horrid has happened to the indenting and braces in this function,
producing a warning:
drivers/hwmon/max1619.c: In function `max1619_detect':
drivers/hwmon/max1619.c:196: warning: `man_id' might be used uninitialized in this function
drivers/hwmon/max1619.c:196: warning: `chip_id' might be used uninitialized in this function
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global function:
- core.c: pnp_remove_device
- #if 0 the following unneeded EXPORT_SYMBOL's:
- card.c: pnp_add_card
- card.c: pnp_remove_card
- card.c: pnp_add_card_device
- card.c: pnp_remove_card_device
- card.c: pnp_add_card_id
- core.c: pnp_register_protocol
- core.c: pnp_unregister_protocol
- core.c: pnp_add_device
- core.c: pnp_remove_device
- pnpacpi/core.c: pnpacpi_protocol
- driver.c: pnp_add_id
- isapnp/core.c: isapnp_read_byte
- manager.c: pnp_auto_config_dev
- resource.c: pnp_register_dependent_option
- resource.c: pnp_register_independent_option
- resource.c: pnp_register_irq_resource
- resource.c: pnp_register_dma_resource
- resource.c: pnp_register_port_resource
- resource.c: pnp_register_mem_resource
Note that this patch #if 0's exactly one functions and removes no
functions. Most it does is the #if 0 of EXPORT_SYMBOL's, so if any modular
code will use any of them, re-adding will be trivial.
Modular ISAPnP might be interesting in some cases, but this is more legacy
code. If someone would work on it to sort all the issues out (starting
with the point that most users of __ISAPNP__ will have to be fixed)
re-enabling the required EXPORT_SYMBOL's won't be hard for him.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EXPORT_SYMBOL's for phys_proc_id and cpu_core_id were added this year but
never used.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no modular usage in the kernel and modules shouldn't use this
symbol.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This looks like something which out-of-tree code could possibly be using.
Give panic_timeout the twelve-month treatment.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This looks like something which out-of-tree code could possibly be using.
Give insert_resource the twelve-month treatment.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage of console_unblank in the
kernel.
This patch was already ACK'ed by Alan Cox.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I didn't find any possible modular usage in the kernel.
This patch was already ACK'ed by Christoph Hellwig.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the security/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in security/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the fs/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in fs/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/s390/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/s390/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Cornelia Huck <cohuck@de.ibm.com>
Acked-by: Stefan Bader <Stefan.Bader@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/isdn/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/isdn/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/char/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/char/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
msecs_to_jiffies() instead of direct HZ division to avoid rounding errors.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded HZ division to avoid
rounding errors.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch splits dentry locking documentation from
Documentation/filesystems/vfs.txt to a separate file. The dentry locking
bits are useful but do not fit into the VFS overview document as is.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the Documentation/filesystems/vfs.txt document. I
rearranged and rewrote parts of the introduction chapter and added better
headings for each section. I also added a description for the inode
rename() operation which was missing and added links to some useful
external VFS documentation.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert to proper kernel-doc format.
Some have extra blank lines (not allowed immed. after the function name)
or need blank lines (after all parameters). Function summary must be only
one line.
Colon (":") in a function description does weird things (causes kernel-doc
to think that it's a new section head sadly).
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various core kernel-doc cleanups:
- add missing function parameters in ipc, irq/manage, kernel/sys,
kernel/sysctl, and mm/slab;
- move description to just above function for kernel_restart()
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix various warnings in kernel-doc:
Warning(linux-2614-rc4//include/linux/net.h:89): Enum value 'SOCK_DCCP' not described in enum 'sock_type'
usercopy.c: should use !E instead of !I for exported symbols:
Warning(linux-2614-rc4//arch/i386/lib/usercopy.c): no structured comments found
fs.h does not need to use !E since it has no exported symbols:
Warning(linux-2614-rc4//include/linux/fs.h:1182): No description found for parameter 'find_exported_dentry'
Warning(linux-2614-rc4//include/linux/fs.h): no structured comments found
irq/manage.c should use !E for its exported symbols:
Warning(linux-2614-rc4//kernel/irq/manage.c): no structured comments found
macmodes.c should use !E for its exported symbols:
Warning(linux-2614-rc4//drivers/video/macmodes.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add structure fields kernel-doc for 2 fields in struct journal_s.
Warning(/var/linsrc/linux-2614-rc4//include/linux/jbd.h:808): No description found for parameter 'j_wbuf'
Warning(/var/linsrc/linux-2614-rc4//include/linux/jbd.h:808): No description found for parameter 'j_wbufsize'
Convert fs/jbd/recovery.c non-static functions to kernel-doc format.
fs/jbd/recovery.c doesn't export any symbols, so it should use
!I instead of !E to eliminate this warning message:
Warning(/var/linsrc/linux-2614-rc4//fs/jbd/recovery.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've recently added this documentation, Alasdair gave some corrections, and
here are some further corrections on top of his work (partly style issue,
partly a technical error due to different past experience, partly a note
which I've added - i.e. transient snapshots are lighter).
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current init code sets hiprilvl to 0 and maxhipri to 5. According to the
specs those values are illegal on both G200 and G400. It also causes
distortions on the TV-out at least when CRTC2 is in YUV mode as is the case
with DirectFB. This patch resets both values to 0.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the CACHEFLUSH register on all chip types. The register is listed in all
other specs except 2064W. However I have verified that the register does work
on a 2064W despite being marked reserved in the specs. There were no
noticeable side effects after writing to the register.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new entries for Mystique AGP with the PCI ID 0x051e.
I don't actually have such boards but according to google they do exist.
Curiosly X.Org doesn't recognize that PCI ID. And what's even more
interesting is that Matrox's own Windows drivers don't recognize it either.
After going through about a dozen different versions I did find one older
driver that does list this particular ID. It is also listed in the pci.ids
file.
I'm not sure if non-220 AGP chips exist. I left the chip revision check
intact for AGP chips nonetheless.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wait_event_event_interruptible() uses a private wait queue entry so there's no
need for the caller to initialize one.
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert i810fb, nvidiafb and savagefb to use the fb_find_best_display helper
when searching for the initial video mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new helper, fb_find_best_display(), which will search the modelist for the
best mode for the attached display. This requires an EDID block that is
converted to struct fb_monspecs and a private modelist. The search will be
done in this manner:
- if 1st detailed timing is preferred, use that
- else if dimensions of the display are known, use that to estimate xres and
- else if modelist has detailed timings, use the first detailed timing
- else, use the very first entry from the modelist
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rearrange mode database entries such that preferred timings are entered first,
and less preferred timings are entered last. (Detailed, VESA,
established/standard).
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I converted the "rl" console font from the kbd utility to be a built-in font
for the framebuffer console, and I was wondering if you would be OK with
including it. I've generated a font_rl.c file and related minor
modifications. I find it's the most visually appealing of the kbd fonts which
is why I use it and selected it for conversion. I believe the font is GPL'd.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The functions for reading the 1st and 2nd bus are essentially the same,
except for the register. Consolidate them all.
- According to Nicolas Boichat, there is an undocumented 3rd i2c bus for
attaching daughter cards. Add support for this.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vesafb occassionally gets the size wrong when setting the mtrr. When X or DRI
attempts to set the mtrr, it will fail due to range overlap significantly
affecting their performance. Disable mtrr and let the user explicitly enable
it with the mtrr:n option.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initialise the .owner field, so that if the driver is built as a module, the
system has a link to the owner
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the fb_find_nearest_mode() function finds a mode with screen
resolution closest to that described by the 'var' argument and with some
arbitrary refresh rate (eg. in the following sequence of refresh rates: 70 60
53 85 75, 53 is selected).
This patch fixes the function so that it looks for the closest mode as far as
both resolution and refresh rate are concerned. The function's first argument
is changed to fb_videomode so that the refresh rate can be specified by the
caller, as fb_var_screeninfo doesn't have any fields that could directly hold
this data.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use do {} while(0) for empty reverse_order() macro.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some EDID blocks set the flag "prefer first detailed timing" without providing
any detailed timing at all. Clear this flag if the block does not provide
detailed timings.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a small patch which configures the correct memory clock and
timings on the Elsa Winner 2000 Office pm2 based card. This is necessary when
the card is used on a platform which does not support PC style BIOS
initialization.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Jean-Philippe Gurard (Bugzilla Bug 1782)
"I've tried with video=atyfb:debug and video=atyfb:debug,mode:1280x600, \
nomtrr.
In both case, the screen stays black, but seems divided into 4 vertical bands.
Some white lines pop up randomly on each vertical band."
The problem is a combination of an incorrect xclk plus lack of timing
information. The adapter is attached to an LCD device that can do 1280x600
(which is not a standard resolution). The global mode database does not have
an entry for it. Fortunately, the Video BIOS contains the complete timing
info for this display, however, atyfb is not making use of it.
Add support to get the timing information from the BIOS, if available.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix out-of-bounds bug. The pseudopalette has room only for 16 entries, thus,
write only the first 16 entries to the pseudopalette.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove software clipping from imageblit, fillrect and copyarea. Clipping is
not needed because the console layer assures that reads/writes doest not
happen beyond the extents of the framebuffer. And software clipping tends to
hide bugs, if they do exist.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If machine has more than 1 driver installed, and they all drive the same
hardware, it's possible that the driver's fb_release() method will attempt to
restore the hardware state to the initial state. This will leave the new
driver in an undefined state. To prevent this problem, initialize the new
driver by calling fb_set_par() when the old driver is released by fbcon.
Signed-off-by: Antonino Daplas<adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of manually filling up the fields in struct fb_var_screeninfo, use the
display_to_var() helper.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lot's of redundant code scattered throughout fbcon.c. Consolidate them all
into one function, fbcon_update_softback().
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to Jon Smirl, filling in the field fb_cursor with soft_cursor for
drivers that do not support hardware cursors is redundant. The soft_cursor
function is usable by all drivers because it is just a wrapper around
fb_imageblit. And because soft_cursor is an fbcon-specific hook, the file is
moved to the console directory.
Thus, drivers that do not support hardware cursors can leave the fb_cursor
field blank. For drivers that do, they can fill up this field with their own
version.
The end result is a smaller code size. And if the framebuffer console is not
loaded, module/kernel size is also reduced because the soft_cursor module will
also not be loaded.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevent spurious recompilations of the radeonfb driver when I2C/DDC support
is not included and i2c header files are modified.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nvidiafb didn't fully hook-up the code it borrowed from X for doing flat
panel dithering (this is useful for 6 bits panels). This adds a driver
option to force it, and by default "reads" the current value from the chip
to get the firmware setting. It significantly improves the quality of
images on the iMac G5 I have here (though the X driver doesn't yet "read"
the current value and defaults to 0, so you have to add Option "FBDither"
"true" to your X config file to get that, I'll try to fix X.org to "read"
the default unless specified asap).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/video/nvidia/nv_setup.c: In function `NVCommonSetup':
drivers/video/nvidia/nv_setup.c:408: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:496: warning: statement with no effect
drivers/video/nvidia/nv_setup.c:504: warning: statement with no effect
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes nvifiafb mode setting code to be closer to what the X
driver does, which actually makes it work on the 5200FX I have access to.
It also fix the routine that gets the EDID from Open Firmware on PPC, it
was broken in various ways and would crash at boot. Compared to the patch
I posted to linux-fbdev last week, this one just changes a printk to be
closer to the other ones in the driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange frame buffer menu:
- puts all Epson drivers together
- removes split of FB_PXA and FB_PXA_PARAMETERS by FB_W100
- results in PXA, W100, Epson, S3C2410, & Virtual FB drivers being
presented at the same menu level as all other FB drivers
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Frame buffer driver help text changes:
- Move S3 Trio next to S3 Savage;
- add or clarify help text for several FB drivers;
- add help text for FB console;
- add help text for bootup logos;
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If an RPC socket is serving multiple programs, then the pg_authenticate of
the first program in the list is called, instead of pg_authenticate for the
program to be run.
This does not cause a problem with any programs in the current kernel, but
could confuse future code.
Also set pg_authenticate for nfsd_acl_program incase it ever gets used.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a couple of tests which could possibly be confused by extremely
large numbers appearing in 'xdr' packets. I think the closest to an exploit
you could get would be writing random data from a free page into a file - i.e.
leak data out of kernel space.
I'm fairly sure they cannot be used for remote compromise.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a file in the NFSD filesystem that allows setting and querying of
which version of NFS are being exported. Changes are only allowed while no
server is running.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most files in the nfsd filesystems are transaction files. You write a
request, and read a response.
For some (e.g. 'threads') it makes sense to just be able to read and get the
current value.
This functionality did exist but was broken recently when someone modified
nfsctl.c without going through the maintainer. This patch fixes the
regression.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a somewhat cosmetic fix to keep the SpecFS validation test from
complaining.
SpecFS want's to try chmod on symlinks, and ext3 and reiser (at least) return
ENOTSUPP.
Probably both sides are being silly, but it is easiest to simply make it a
non-issue and filter out chmod requests on symlinks at the nfsd level.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the warning "Debug: sleeping function called from invalid context at
include/asm/semaphore.h:102" that the zr36067 driver emits every time an
application using JPEG capture starts up (e.g. mjpegtools' lavrec).
The warning is harmless, but clogs up the dmesg output. This was logged as
bugzilla #5403. (Thanks to Christian Casteyde for helping me in fixing
this long-standing annoyance.)
Signed-off-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates the RIO messaging interface to pass a device instance into the
event registeration and callbacks.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds PPC32 RIO support. Init code for the MPC85xx RIO ports and glue for the
STx GP3 board to use it.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Addresses issues raised with the 2.6.12-rc6-mm1 RIO support. Fix dma_mask
init, shrink some code, general cleanup.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds RapidIO enumeration/discovery.
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add RapidIO core include files.
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a RapidIO subsystem to the kernel. RIO is a switched fabric interconnect
used in higher-end embedded applications. The curious can look at the specs
over at http://www.rapidio.org
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
There's a lot more to do to take advantages of all the hardware features.
However, this should provide a good base for folks with RIO hardware to start
contributing.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the base kprobes infrastructure to use RCU for synchronization
during kprobe registration and unregistration. These changes coupled with the
arch kprobe changes (next in series):
a. serialize registration and unregistration of kprobes.
b. enable lockless execution of handlers. Handlers can now run in parallel.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86_64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using a arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sparc64 changes to track kprobe execution on a per-cpu basis. We now track
the kprobe state machine independently on each cpu using an arch specific
kprobe control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PPC64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I386 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu, using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the base kprobe infrastructure to track kprobe execution on a
per-cpu basis.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a panic came from the IPMI watchdog pretimeout and that was reported via
an NMI, it would also be reported via the standard IPMI flags, which would
get picked up when reporting panic events and cause another panic. This
adds an atomic to avoid calling panic twice.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use rcu_read_lock for the cmd_rcvrs list, since that was what what
intended, anyway. This means that all the users of the cmd_rcvrs_lock are
tasks, so the irq disables are no longer required for that lock and it can
become a semaphore.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must poll for responses to commands when interrupts aren't in use. The
default poll interval is based on using a kernel timer, which varies with HZ.
For character-based interfaces like KCS and SMIC though, that can be way too
slow (>15 minutes to flash a new firmware with KCS, >20 seconds to retrieve
the sensor list).
This creates a low-priority kernel thread to poll more often. If the state
machine is idle, so is the kernel thread. But if there's an active command,
it polls quite rapidly. This decrease a firmware flash time from 15 minutes
to 1.5 minutes, and the sensor list time to 4.5 seconds, on a Dell PowerEdge
x8x system.
The timer-based polling remains, to ensure some amount of responsiveness even
under high user process CPU load.
Checking for a stopped timer at rmmod now uses atomics and del_timer_sync() to
ensure safe stoppage.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BMCs can get into ERROR0 state while flashing new firmware, particularly while
the BMC is erasing the next flash block, which may take a just under 2 seconds
on a Dell PowerEdge 2800 (1.75 seconds typical), during which time the
single-threaded firmware may not be able to process new commands. In
particular, clearing OBF may not take effect immediately.
We want it to delay in ERROR0 after clearing OBF a bit waiting for OBF to
actually be clear before proceeding.
This introduces a new return value from the LLDD's event loop,
SI_SM_CALL_WITH_TICK_DELAY. This means the calling thread/timer should
schedule_timeout() at least 1 tick, rather than busy-wait. This is a longer
delay than SI_SM_CALL_WITH_DELAY, which is typically a 250us busy-wait.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current BT retry/reset mechanism fails to succeed on a PowerEdge 1650,
when the controller is wedged with B2H_ATN asserted at XACTION_START. If this
occurs, no further commands will ever succeed unless the state of the
controller is first cleared out.
Furthermore, the soft reset would only occur if the first command after insmod
was the one that timed out, not if a later command timed out.
This patch changes the retry/reset mechanism to be as follows:
Before retrying a command, clear the state of the BT controller such that the
flags represent ready for a new transaction. This increases the chance of
success of the restarted transaction.
After 2 retries, issue a soft reset and retry one more time before giving up
and reporting back a failure.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some commands, on some system BMCs, don't respond at at all. This is seen on
Dell PowerEdge x6xx and x7xx systems with IPMI 1.0 BT controllers when a "Get
SDR" command is issued, with a length field of 0x3A, which happens to be the
length of about SDR entries. If another length is passed, this command
succeeds.
This patch adds general infrastructure for receiving commands before they're
passed down to the low-level drivers, such that they can be completed
immediately, or modified, prior to being sent to ->start_transaction().
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make SMIC driver ignore EVT_AVAIL and SMS_ATN bits in flags register, as
they're used by systems management interrupts, not the host OS.
Make the OEM0 Data Available handler work for pre-IPMI 1.5 systems from Dell
too.
Without these two fixes, PowerEdge 2650 and other similar systems with SMIC
may hang a process (modprobe or anything using /dev/ipmi0).
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make module_param and MODULE_PARAM_DESC agree on poweroff_powercycle name.
There was an extraneous ifdef in the IPMI poweroff code that prevented it from
working if PROC_FS was disabled.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the IPMI watchdog parameters (the ones that make sense) to be exported
from sysfs. This is somewhat complicated because these parameters have
side-effects that must be handled.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A number of small changes for the various system interface drivers,
consolidated from a number of patches from Matt Domsch.
Clear B2H_ATN and drain the BMC message buffer on command timeout. This
prevents further commands from failing after a timeout.
Add bt_debug and smic_debug module parameters, expose them in sysfs. This
lets you enable and disable debugging messages at runtime.
Unsigned jiffies math in ipmi_si_intf.c causes a too-large value to be passed
to ->event() after jiffies wrap-around. The BT driver had caught this, but
didn't know how to fix it. Now all calls to ->event() use a sane value for
time.
Increase timeout for commands handed to the BT driver from 2 seconds to 5
seconds. This is necessary particularly when the previous command was a
"Clear SEL", as that command completes, yet the BMC isn't really ready to
handle another command yet.
Silence BT debugging messages which were being printed on the console.
Increase SMIC timeout form 1/10s to 2s. This is needed on Dell PowerEdge 2650
and PowerEdge 750 with ERA/O cards to allow commands to complete without
timing out.
Adds kcs_debug module param, to match behavior of BT and SMIC. This also
prevents messages from being sent to the console unless explicitly requested.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is rather large, but it really can't be done in smaller chunks
easily and I believe it is an important change. This has been out and tested
for a while in the latest IPMI driver release. There are no functional
changes, just changes as necessary to convert the locking over (and a few
minor style updates).
The IPMI driver uses read/write locks to ensure that things exist while they
are in use. This is bad from a number of points of view. This patch removes
the rwlocks and uses refcounts and RCU lists to manage what the locks did.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce the notion of cooperating processes (those that submit requests
close to one another), and use these statistics to make better choices about
whether or not to do anticipatory waiting.
Help and analysis from Seetharami Seelam <seelam@cs.utep.edu>
Performance testing from Seelam:
I set up my system and executed a couple of tests that I used for OLS. I
tested with AS, cooperative process patch merged in -mm tree (which I called
Nick, below) and the cooperative patch with modifications to as_update_iohist
(which I called Seelam).
I used a dual-processor (2.28GHz Pentium 4 Xeon) system, with 1 GB main memory
and 1 MB L2 cache, running Linux 2.6.9. Only a single processor is used for
the experiments. I used 7.2K RPM Maxtor 10GB drive configured with ext2 file
system.
Experiment 1 (ex1) consists of reading one Linux source trees using
find . -type f -exec cat '{}' ';' > /dev/null.
Experiment 2 (ex2) consists of reading two disjoint Linux source trees
using
find . -type f -exec cat '{}' ';' > /dev/null.
Experiment 3 (ex3) consists of streaming read of a 2GB file in the background
and 1 instance of the chunk reads in Experiment 1.
Timings for reading the Linux source are shown below:
AS Nick Seelam
ex1: 0m25.813s 0m27.859s 0m27.640s
ex2: 1m11.468s 1m13.918s 1m5.869s
ex3: 81m44.352s 10m38.572s 6m47.994s
The difference between the numbers in Experiment 3 must be due to the code in
as_update_iohist. (akpm: that's not part of this patch. So this patch is
"Nick").
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch passes the file handle supplied in iattr to userspace, in case the
->setattr() was invoked from sys_ftruncate(). This solves the permission
checking (or lack thereof) in ftruncate() for the class of filesystems served
by an unprivileged userspace process.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds an atomic create+open operation. This does not yet work if
the file type changes between lookup and create+open, but solves the
permission checking problems for the separte create and open methods.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new access call, which will only be called if ->permission is invoked
from sys_access(). In all other cases permission checking is delayed until
the actual filesystem operation.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Though the following changes are all backward compatible (from the kernel's as
well as the library's POV) change the minor version, so interested
applications can detect new features.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch extends the iattr structure with a file pointer memeber, and adds
an ATTR_FILE validity flag for this member.
This is set if do_truncate() is invoked from ftruncate() or from
do_coredump().
The change is source and binary compatible.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sys_ptrace boilerplate code (everything outside the big switch
statement for the arch-specific requests) is shared by most architectures.
This patch moves it to kernel/ptrace.c and leaves the arch-specific code as
arch_ptrace.
Some architectures have a too different ptrace so we have to exclude them.
They continue to keep their implementations. For sh64 I had to add a
sh64_ptrace wrapper because it does some initialization on the first call.
For um I removed an ifdefed SUBARCH_PTRACE_SPECIAL block, but
SUBARCH_PTRACE_SPECIAL isn't defined anywhere in the tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-By: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Both AFFS and HPFS update the ctime and mtime in the write path, after
generic_file_write returned and marked the inode dirty.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
afs actually had a write method that returned different errors depending on
whether some flag was set - better return the standard EINVAL errno.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to duplicate a generic readonly file ops table in befs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to duplicate a generic readonly file ops table in befs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a memory leak possible in dentry_open(). If get_empty_filp()
fails, then the references to dentry and mnt need to be released. The
attached patch adds the calls to dput() and mntput() to release these two
references.
Signed-off-by: Peter Staubach <staubach@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates to Documentation/vm/hugetlbpage.txt:
- there's no need to select HUGETLB_PAGE manually and it's no longer
under the processor menu. Update the text accordingly.
- fix typos and trim trailing whitespace.
Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Get rid of the `int unused' parameter of __find_get_block_slow().
Signed-off-by: Coywolf Qi Hunt <qiyong@fc-cn.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Data allocated with "__getname()" should always be free'd with "__putname()"
because of the AUDITSYSCALL code.
Signed-off-by: Davi Arnaut <davi.arnaut@gmail.com>
Cc: Urban Widmark <urban@teststation.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- "extern inline" -> "static inline"
- every file should #include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mikael Pettersson <mikpe@csd.uu.se> noted that the current 2.6-git (and 2.4)
patch to disallow KDSKBSENT for unpriviledged users should be less restrictive
allowing reading of current function key string entry, but not writing.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code for FUTEX_WAKE_OP calls an arch callback,
futex_atomic_op_inuser(). That callback can return an error code, but
currently the caller assumes any error is EFAULT, and will try various
things to resolve the fault before eventually giving up with EFAULT
(regardless of the original error code). This is not a theoretical case -
arch callbacks currently return -ENOSYS if the opcode they are given is
bogus.
This patch alters the code to detect non-EFAULT errors and return them
directly to the user.
Of course, whether -ENOSYS is the correct return value for the bogus opcode
case, or whether EINVAL would be more appropriate is another question.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jamie Lokier <jamie@shareable.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AIO was adding a new context's max requests to the global total before
testing if that resulting total was over the global limit. This let
innocent tasks get their new limit tested along with a racing guilty task
that was crossing the limit. This serializes the _nr accounting with a
spinlock It also switches to using unsigned long for the global totals.
Individual contexts are still limited to an unsigned int's worth of
requests by the syscall interface.
The problem and fix were verified with a simple program that spun creating
and destroying a context while holding on to another long lived context.
Before the patch a task creating a tiny context could get a spurious EAGAIN
if it raced with a task creating a very large context that overran the
limit.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch removes a couple of incorrect and obsolete '!' operators
left over from the conversion of the key permission functions from
true/false returns to zero/error returns.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reiser4 uses radix trees to solve a trouble reiser4_readdir has serving nfs
requests.
Unfortunately, radix tree api lacks an operation suitable for modifying
existing entry. This patch adds radix_tree_lookup_slot which returns pointer
to found item within the tree. That location can be then updated.
Both Nick and Christoph Lameter have patches which need this as well.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a few comments surrounding the generic readahead API.
Also convert some ulongs into pgoff_t: the identifier for PAGE_CACHE_SIZE
offsets into pagecache.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add SHM_NORESERVE functionality similar to MAP_NORESERVE for shared memory
segments.
This is mainly to avoid abuse of OVERCOMMIT_ALWAYS and this flag is ignored
for OVERCOMMIT_NEVER.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The -EROFS check has moved up to permission() in the VFS a while ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has the changes to support the memory floor fix done in Dell
BIOS. The BIOS incase of packet update mechanism would not accept packet
placed in memory below a cretain address. This address is by default 128K
but can change. The driver now can accept the memory floor if the user
chooses to make it will try to allocate contiguous physical memory above
the memory floor by allocating a set of packets till a valid memory
allocation is made. All the allocates then are freed. This repeats for
everty packet.
This patch was created by Michael E Brown and has been tested on 2.6.14-rc5
Signed-of-by: Michael E Brown <Michael_E_Brown@Dell.com>
Signed-off-by: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
driver_unregister is not being properly called when the init function
returns an error case. Restructured the return logic such that this and
the other cleanups all happen in one place. Preformed many of the cleanups
that Andrew Morton's patch on Thursday made in tpm_atmel.c. Fixed
Matthieu's concern about writing before discovery.
(akpm: rmk said:
This driver is buggy. You must not provide your own release function - it
doesn't solve the problem which the warning (which you get when you don't
provide one) is telling you about.
You should convert your device driver over to the replacement dynamic platform
support, once it is merged. IOW, something like:
pdev = platform_device_alloc("mydev", id);
if (pdev) {
err = platform_device_add_resources(pdev, &resources,
ARRAY_SIZE(resources));
if (err == 0)
err = platform_device_add_data(pdev, &platform_data,
sizeof(platform_data));
if (err == 0)
err = platform_device_add(pdev);
} else {
err = -ENOMEM;
}
if (err)
platform_device_put(pdev);
)
Signed-off-by: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In a case documented as
We should never be called with any of these states
BUG() in a case that would later result in a NULL pointer dereference.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a wrong BUG in mxser_close.
The BUG is triggered when tty->driver_data == NULL, But in fact this is not
a bug, because tty->driver->close is called even when tty->driver->open
fails.
LDD3 tells us to do nothing in such cases.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove explicit tty_driver ops initialisation, because this is already done
by tty_set_operations.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch identifies the HPET Maintainers. Clemens in taking over as
primary maintainer for the HPET driver. Clemens has i386 hardware with
HPET and is a better choice than me because of this. I've shared this
patch with all cc: recipients and there is agreement on ownership.
Hopefully this eliminates future confusion in terms of where HPET
maintenance is owned.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Cc: <clemens@ladisch.de>
Cc: <venkatesh.pallipadi@intel.com>
Cc: <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by Eddy Petrisor <eddy.petrisor@gmail.com>
fs/built-in.o(.text+0x35fdc): In function `hfs_mdb_put':
: undefined reference to `unload_nls'
fs/built-in.o(.text+0x35ff1): In function `hfs_mdb_put':
: undefined reference to `unload_nls'
fs/built-in.o(.text+0x367a5): In function `parse_options':
super.c: undefined reference to `load_nls'
fs/built-in.o(.text+0x367db):super.c: undefined reference to `load_nls'
fs/built-in.o(.text+0x36938):super.c: undefined reference to `load_nls_default'
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the hlist_for_each_rcu() API, which is used only in one place, and
is trivially converted to hlist_for_each_entry_rcu(), making the code
shorter and more readable. Any out-of-tree uses may be similarly
converted.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a connector that reports fork, exec, id change, and exit
events for all processes to userspace. It replaces the fork_advisor patch
that ELSA is currently using. Applications that may find these events
useful include accounting/auditing (e.g. ELSA), system activity monitoring
(e.g. top), security, and resource management (e.g. CKRM).
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the backing_dev_info doesn't have BDI_CAP_NO_WRITEBACK we're not supposed
to write back an inode's pages. But in this situation write_inode_now()
refuses to write the inode itself as well. Fix.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Large console spews from IRQ or local_irq_disable() sections can cause the NMI
watchdog to go off.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge common parts of head.S and head64.S into head.S and move architecture
specific parts to head31.S and head64.S respectively. Saves us ~500 lines
of duplicated assembly code.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If vmcp is interrupted by a signal the vmcp command buffer is not freed.
Found by Pete Zaitcev.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using __typeof__(*ptr) on a pointer to const makes the __x variable in
__get_user const as well. The latest gcc will refuse to write to it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Access to FBA disks via DIAG fails for block sizes > 512 byte. The device
analysis code of the DIAG discipline does not properly initialize the DIAG250
device environment after completion of the analysis. This results in VM only
serving 512 bytes per block I/O request whereas Linux expects larger block
sizes. Add proper device environment setup to end of analysis code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Future versions of gcc may remove initialization code for control blocks used
by the diag250 inline assembly due to incompletely specified constraints.
This may lead to erratic behavior. Fix the diag250 inline assembly
constraints.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The test_bit function returns a non-boolean value, it returns 0,1,2,4,...
instead of only 0 or 1. This causes wrongs results in the mincore system
call. Check against 0 to get a proper boolean value.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove pagex pseudo page fault code. It does not work together with the
system call speedup that makes the complete system call path enabled for
interrupts. To make pagex and the syscall speedup code work together we would
have to add code to the program check handler to do a critical section cleanup
like the asynchronous interrupt code. This would make program checks slower.
Not what we want.
Newer versions of z/VM have the improved pfault pseudo page fault interface.
This replaces the old pagex interface and does not have the problem. So its
better to just rip out the pagex code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the interface for setting ccw group devices on-/offline consistent with
that for ccw devices: Check if the device driver provided a set_{on,off}line
function and just set the device on-/offline if not.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't switch back to 24 bit addressing mode when waiting for an external
interrupt and set the correct bit in wait PSW (external mask instead of I/O
mask).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix typos and add a section about cpus in the driver-model documentation.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The calculation of the value return by next_timer_interrupt from jiffies to
jiffies_64 is racy against xtime updates. We need to protect the calculation
with read_seqbegin/read_seqretry.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Always create all signal frames for pending signals before returning to
userspace, not just a single one.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No one may sleep on us until we've been down()'d. So on allocation,
initialize `sleepers' to 0, just like everyone else does.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Acked-by: Christian Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch reverts back the changes to HOSTCFLAGS and HOSTLDFLAGS
When we were building complete binaries to get constants (such as ptrace
register layout on stack) from host userspace headers, we needed to make the
arch for building HOST binaries match our one: i.e. on a 64bit system
compiling 32bit binaries, we compile 32-bit hostprogs and need, say, 32-bit
ncurses. Now we can revert that - that avoids problem with, say, menuconfig
and ncurses, on a system which can't compile well 32-bit programs.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove usage of hardcoded constants in paging_init().
By chance I spotted a bug in zones_setup involving a change to ZONE_*
constants, due to the ZONE_DMA32 patch from Andi Kleen (which is in -mm).
So, possibly, instead of zones_size[2] you will find zones_size[3] in the
code, but that change is wrong and this patch is still correct.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A number of fixes to improve behavior when large physical memory sizes
are specified:
- libc files need -D_FILE_OFFSET_BITS=64 because there are unavoidable uses
of non-64 interfaces in libc
- some %d need to be %u
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch imlements full LDT handling in SKAS:
* UML holds it's own LDT table, used to deliver data on
modify_ldt(READ)
* UML disables the default_ldt, inherited from the host (SKAS3)
or resets LDT entries, set by host's clib and inherited in
SKAS0
* A new global variable skas_needs_stub is inserted, that
can be used to decide, whether stub-pages must be supported
or not.
* Uses the syscall-stub to replace missing PTRACE_LDT (therefore,
write_ldt_entry needs to be modified)
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not quite, something along the lines of the patch below works correctly (and
makes aio performance not suffer from multiple second delays), as skas0 mode
correctly switches mm contexts, unlike TT (which should probably get nuked
from the kernel now that skas0 seems to be working).
Signed-off-by: Benjamin LaHaise <bcrl@linux.intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from main.c file under os-Linux dir and joins mem.c
and um_arch.c files.
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ifa->ifa_address and ifa->ifa_mask are defined as __u32, but used as if they
were char[4].
Network code uses htons() to convert it. So UML's method to access these
fields is wrong for bigendians (e.g. s390)
I replaced bytewise copying by memcpy(), maybe even that might be removed, if
ifa->ifa_address/mask may be used immediately.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike noted that the assembly code for syscall stubs is misassembled with
GCC 3.2.3: the values copied in registers weren't preserved between one asm()
and the following one.
So I fixed the thing by rewriting the __asm__ constraints more like unistd.h
ones.
Note: in syscall6 case I had to add one more instruction (i.e. moving arg6 in
eax and shuffling things around) - it's needed for the function to be valid in
general (we can't load the value from the stack, relative to ebp, because we
change it), but could be avoided since we actually use a constant as param 6.
The only fix would be to turn stub_syscall6 to a macro and use a "i"
constraint for arg6 (i.e., specify it's a constant value).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some more debugging information when a stub does something unexpected,
usually segfaulting. Now, it dumps out the stub's registers as well as the
signal.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() already declared in include/linux/kernel.h so squish the
duplication. Besides, no printk() usage here. Bye bye.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's widely seen a MCE non-fatal error reported after resume. It seems MCE
resume is lacked under ia32. This patch tries to fix the gap.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unused variable, and make code less evil that way. Fix whitespace
around for-loop-like macro.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This cleans spaces between * and pointer up, and adds "int" in "unsigned
int".
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds few more working systems.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace smp_processor_id() with any_online_cpu(cpu_online_map) in order to
avoid lots of "BUG: using smp_processor_id() in preemptible [00000001]
code:..." messages in case taking a cpu online fails.
All the traces start at the last notifier_call_chain(...) in kernel/cpu.c.
Since we hold the cpu_control semaphore it shouldn't be any problem to access
cpu_online_map.
The reason why cpu_up failed is simply that the cpu that was supposed to be
taken online wasn't even there. That is because on s390 we never know when a
new cpu comes and therefore cpu_possible_map consists of only ones and doesn't
reflect reality.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every file should #include the header files containing the prototypes of
its global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Excerpt from bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=5518
"i386 version of Reboot-through-BIOS is unsafe: it forgets to mask APIC LVT
interrupts before jumping to a BIOS entry point. As a result, BIOS ends up
bombarded with interrupts early on boot. The BIOS does not expect it since
following a "normal" hardware cpu reset, all APIC LVT registers have the
Mask bit (16) set and can't generate interrupts.
For example, the version of Phoenix BIOS used by VMware enables interrupts
for the first time before masking/clearing APIC LVT. The APIC Timer LVT
register is still set up for a timer interrupt delivery with a high vector
from the previous Linux incarnation (0xef in our case). The BIOS has not
fully initialized its IDT at this point and the real mode gate for 0xef
remains all zeros. Vector 0xef dispatches BIOS to address 0:0, BIOS takes
a #GP and eventually hangs.
machine_shutdown() does attempt to shut down APIC before jumping to BIOS,
but it is ineffective"
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SH7705 in extended cache mode has some left-over VALID_PAGE() cruft that it
checks when doing lazy dcache write-back. This has been gone for some time
(the last bits were in the discontig code, which should now also be gone --
this also fixes up a build error in the non-discontig case).
pfn_valid() gives the desired behaviour, so we switch to that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was only one board using this (hp690 specifically), and it just so
happens that it's only physically discontiguous at the "normal" P1 offset. If
we bump up the P1 offset, it's possible to hit a shadowed region of memory
where we suddenly become magically contiguous.
As people have been using this shadowed region workaround for quite some time
(and without any adverse effects), it's time to drop the left over discontig
bits that no longer have any practical use (it was always very much
hp690-centric to begin with).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently it is bogus to call pte_mkhuge() outside of the CONFIG_HUGETLB_PAGE
context, as the only processors that support _PAGE_SZHUGE do so in the
hugetlbpage context only (and this is the only time that _PAGE_SZHUGE is even
defined). SH-2 and SH-3 do not support huge pages at all, and so it is not
possible to enable this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds support for the relatively quirky (ie, not in line with any known
documentation, and amazed it works at all) SuperHyway implementation on
SH4-202. This depends on the earlier SuperHyway patch for multiple block
support and VCR refactoring.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This extends the API somewhat to allow for platform-specific VCR reading and
writing. Some platforms (like SH4-202) implement the VCR in a split VCRL and
VCRH, but end up being in reverse order or have other quirks that need to be
dealt with, so we add a set of superhyway_ops per-bus to accomodate this.
We also have to extend the per-device resources somewhat, as some devices now
conveniently split control and data blocks. So we allow a platform to
register its set of SuperHyway devices via superhyway_add_devices() with the
control block always ordered as the first resource (as this is the one that
userspace cares about).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sh had its own support for embedding ramdisk images in to the kernel binary,
but people are using initramfs for this now, so we drop the ramdisk embedding.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/sh/ got dropped from drivers/Makefile, so add it back in..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On PPC405GP/GPR it should be possible to enable PCI support, even when the
internal PCI arbiter is disabled (e.g. when using an external PCI
arbiter). The removed code didn't allow this, and also generated a warning
on PPC405EP platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup PPC40x eval boards (bubinga, walnut and sycamore) to support U-Boot
as bootloader. The OpenBIOS bd_info struct is not used in the kernel
anymore (only U-Boot now).
uImage (U-Boot) tested on walnut, sycamore and bubinga
zImage (OpenBIOS) tested on sycamore, bubinga and ebony
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a
high-throughput segment and a low-latency segment). Fix our PLB register
definitions to cope with this, and add code to dump the status of both
segments when a machine check occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers
are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440
chips. To allow for this, this patch moves the definition of the ERPN used
for mapping UART0 from being hard-coded in the head_44x.S assembly code to
being defined in ibm44x.h.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds watchdog, RTC support for Marvell EV64360BP board.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not valid to enable scatter/gather without hardware checksum support
of some kind. (akpm: applies only to the old boomerang cards).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add capability for 3c59x driver to use memory-mapped PCI I/O resources.
This may improve performance for those devices so equipped. This will be
the default behaviour for IS_CYCLONE and IS_TORNADO devices. Additionally,
it can be enabled/disabled individually for up to MAX_UNITS number of
devices via the use_mmio module option or for all units via the
global_use_mmio option. The use_mmio option overrides the global_use_mmio
option for those devices specified.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only increment rx_dropped in case of lack of resources (i.e. not for
frames with errors).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct several (apparently cut & paste) grammatical typos in module
parameter descriptions. They seem to have originated as copies of the
description for "global_options".
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Beautify the array initilizations for the module parameters.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add bounds checking to usage of hw_checksums module parameter array.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to spare some I/O operations, be more intelligent about when to
read from the PHY.
Pointed out by Bogdan Costescu.
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up mdio_read routines in 3c59x.c to use the MII_* macros defined in
include/linux/mii.h
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert 3c59x driver to use pci_iomap API. This makes it easier to enable
the use of memory-mapped PCI I/O resources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chen noticed that cache_reap uses REAPTIMEOUT_CPUC+smp_processor_id() as
the timeout for rescheduling.
The "+smp_processor_id()" part is wrong, the timeout should be identical
for all cpus: start_cpu_timer already adds a cpu dependant offset to avoid
any clustering.
The attached patch removes smp_processor_id().
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch renames struct kmem_cache_s to kmem_cache so we can start using
it instead of kmem_cache_t typedef.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
slab presently goes BUG if someone tries to register an already-registered
cache.
But this can happen if the user accidentally loads a module which is already
statically linked into the kernel. Nuking the kernel is rather a harsh
reaction.
Change it into a warning, and just fail the kmem_cache_alloc() attempt. If
the module is well-behaved, the modprobe will fail and all is well.
Notes:
- Swaps the ranking of cache_chain_sem and lock_cpu_hotplug(). Doesn't seem
important.
Acked-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
!unlikely(expr) hurts my brain. likely(!expr) is more straightforward.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops, some last minute changes caused the 64K pages patch to break ppc32
build, this fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zImage wrapper has a bug where it doesn't claim() the memory for the
kernel properly, it forgets to take into account the offset between the ELF
header and the kernel itself. This results on some machines, like G5s,
into a kernel that crashes at boot when clearing the BSS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Suppress split ptlock on arches which may use one page for multiple page
tables. Reconsider what better to do (particularly on ppc64) later on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current ia64 implementation of dma_get_cache_alignment does not work
for modules because it relies on a symbol which is not exported. Direct
access to a global is a little ugly anyway, so this patch re-implements
dma_get_cache_alignment in a manner similar to what is currently used for
x86_64.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A typo fix for fix-build-on-nls-free-systems.patch that caused all systems
to be detected as not having NLS.
Signed-off-by: Yuri Vasilevski <yvasilev@duke.math.cinvestav.mx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch, however, should be applied on top of the 64k-page-size patch to
fix some problems with hugepage (some pre-existing, another introduced by
this patch).
The patch fixes a bug in the SLB miss handler for hugepages on ppc64
introduced by the dynamic hugepage patch (commit id
c594adad56) due to a misunderstanding of the
srd instruction's behaviour (mea culpa). The problem arises when a 64-bit
process maps some hugepages in the low 4GB of the address space (unusual).
In this case, as well as the 256M segment in question being marked for
hugepages, other segments at 32G intervals will be incorrectly marked for
hugepages.
In the process, this patch tweaks the semantics of the hugepage bitmaps to
be more sensible. Previously, an address below 4G was marked for hugepages
if the appropriate segment bit in the "low areas" bitmask was set *or* if
the low bit in the "high areas" bitmap was set (which would mark all
addresses below 1TB for hugepage). With this patch, any given address is
governed by a single bitmap. Addresses below 4GB are marked for hugepage
if and only if their bit is set in the "low areas" bitmap (256M
granularity). Addresses between 4GB and 1TB are marked for hugepage iff
the low bit in the "high areas" bitmap is set. Higher addresses are marked
for hugepage iff their bit in the "high areas" bitmap is set (1TB
granularity).
To avoid conflicts, this patch must be applied on top of BenH's pending
patch for 64k base page size [0]. As such, this patch also addresses a
hugepage problem introduced by that patch. That patch allows hugepages of
1MB in size on hardware which supports it, however, that won't work when
using 4k pages (4 level pagetable), because in that case hugepage PTEs are
stored at the PMD level, and each PMD entry maps 2MB. This patch simply
disallows hugepages in that case (we can do something cleverer to re-enable
them some other day).
Built, booted, and a handful of hugepage related tests passed on POWER5
LPAR (both ARCH=powerpc and ARCH=ppc64).
[0] http://gate.crashing.org/~benh/ppc64-64k-pages.diff
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
rtc_control() may be called in the interrupt context in ALSA rtc-timer
driver. The patch fixes the wrong irq enable in rtc.c, and also fixes
the possible race of bit flags.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to set the shared memory attribute in the page tables
on SMP systems to allow the cache coherency to operate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We've noticed that sometimes "MTD do_write_buffer(): software timeout"
message was printed out when writing to a Fujitsu NOR flash.
It turned out that this was because of a race in the timeout handling
do_write_buffer(). A small timeout of (HZ / 1000) + 1 is used there, and
sometimes if the timer interrupt handling takes more than one or even two
jiffies (which is 1-2 ms with HZ == 1000) and that interrupt happens just
after chip_ready() call, the driver bails out from a ready polling loop
despite the chip has actually become ready while all those interrupts were
handled. To deal with this issue, extra check for chip ready is neccessary on
timeout expiration (and the checks should better be reordered).
As do_write_oneword() uses the same approach, it needs to also be changed.
Signed-off-by: Konstantin Baidarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following patch adds support for the TQ Systems TQM834x Boards.
Verified on TQM8349L.
This is a resubmit after integrating the suggested changes.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix two compile warnings that occur because of treating two
'unsigned long's as 'void *'s.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't request_irq before the registers are reset/init.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is no need to save/restore the irq state as the irq are always
locally disabled when b44_interrupt is issued.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove unneeded forward declarations
- s/kmalloc + memset/kzalloc/
- whitespace readjustement can't hurt
- wrong comment: b44_init_rings _is_ called with a spinlock held in
b44_{open/set_ringparam/set_pauseparam/etc}.
Actually, it does not need to be able to sleep
- b44_remove_one() can not be issued with a NULL device in its
private member: remove the test.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch simply factors out the release of the lock.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mostly this involves adding #include <asm/smp.h>, since that defines
things like boot_cpuid[_phys] and [gs]et_hard_smp_processor_id, which
are SMP-related but still needed on UP. This incorporates fixes
posted by Olof Johansson and Heikki Lindholm.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ancient ppcdebug/PPCDBG mechanism is now only used in two places.
First, in the hash setup code, one of the bits allows the size of the
hash table to be reduced by a factor of 8 - which would be better
accomplished with a command line option for that purpose. The other
was a bunch of bus walking related messages in the iSeries code, which
would seem to be insufficient reason to keep the mechanism.
This patch removes the last traces of this mechanism.
Built and booted on iSeries and pSeries POWER5 LPAR (ARCH=powerpc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add nicer printing of faulting address on unresolvable kernel faults.
Makes life a little easier for those who don't know how to decode our
register contents at oops time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds exception table entries for I/O instructions on and
changes MachineCheckException() slightly to cover 8xx specifics (on
8xx the MCE can be generated while executing the IO access instruction
itself, which is not the case on PowerMac's, as the comment on traps.c
details).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch against m8xx_wdt.c adds <asm/io.h> (required for
out,in_be32/16) and fixes syntatic problems introduced with the IO
accessor macro update.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
setup_irq() aborts immediately if there's no handler for the IRQ in
question. So i8259_init() should set up its handlers before trying to
set up the cascade on IRQ 2.
With this and the patch I sent a few days ago to fix initrd on ppc32, my
Pegasos now runs the arch/powerpc kernel.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The assignement of a "const char *" to a "char *" variable
is emitting a warning with gcc 4.0. We cannot change
mtd->name to "const char *" as we have dynamic assignements
of the name. So casting is the correct solution here
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of
bounds when crossing an erase block boundary, causing incorrect OOB data
to be written and corrupting memory. Reset the index to zero after
re-preparing oobbuf for a new erase block.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of an odd offset, the result was shifted by 1 instead of 8
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch contains the arch/ppc64 bits for enabling DLPAR and PCI
Hotplug for the new OF-based PCI probe mechanism. This code path is
currently broken.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel
base page size to 64K. The resulting kernel still boots on any
hardware. On current machines with 4K pages support only, the kernel
will maintain 16 "subpages" for each 64K page transparently.
Note that while real 64K capable HW has been tested, the current patch
will not enable it yet as such hardware is not released yet, and I'm
still verifying with the firmware architects the proper to get the
information from the newer hypervisors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two small fixes for the umad module:
- set kobject name for issm device properly
- in ib_umad_add_one(), s is subtracted from the index i when
initializing ports, so s should be subtracted from the index when
freeing ports in the error path as well.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Use map.virt instead of map.map_priv_1 since it has the correct type.
- Use readw/writew instead of dereferencing an ioremap'd cookie.
- Remove an unused variable.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change to the extended cfi table parsing for Intel NOR flash that uses
the info in the extended table to 'walk' the table rather than using
hard coding for various primary extended query table version numbers.
From: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some callers to block-layer commit_write function treat non-zero return as
error, notably the loopback mount driver sometimes used in conjunction with
JFFS2 on NAND flash for bad block avoidance, etc. Return zero for success
as do various other commit_write functions.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If they get inlined into non __xipram functions we're screwed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added .owner initialisation to allow the
tracking of the device_driver owners when
built as a module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner to device driver field for tracking
when loaded as a module.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner fields to the device_driver for tracking
ownership when built as a module
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't assume eraseblock size is power of 2.
Dataflash can have aligned eraseblock size.
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- assume wbuf may be of size which is not power of 2
- don't make strange assumption about not padding wbuf for DataFlash
- use wbuf = DataFlash page and eraseblock >= 8 Dataflash pages
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
glibc expects to count lines beginning with "processor" to determine
the number of processors, not lines beginning with "Processor". So,
give glibc the format it expects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Simplify the debugging code further.
Update the TODO list
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Always keep valid data in reserved_size.
It did not cause problems, but the reservation code was unoptimal
when centralized summary was active or the size of the erase block
was very small.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do the summary collection in the right place. If the device
was not writebuffered but had c->mtd->writev function
(e.g. blkmtd) the summary collector function was not called.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Intel chip driver has a reboot notifier so no need to reset the chip here.
- Don't play with chip selects (platform code should do this if necessary).
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The goal of summary is to speed up the mount time. Erase block summary (EBS)
stores summary information at the end of every (closed) erase block. It is
no longer necessary to scan all nodes separetly (and read all pages of them)
just read this "small" summary, where every information is stored which is
needed at mount time.
This summary information is stored in a JFFS2_FEATURE_RWCOMPAT_DELETE. During
the mount process if there is no summary info the orignal scan process will
be executed. EBS works with NAND and NOR flashes, too.
There is a user space tool called sumtool to generate this summary
information for a JFFS2 image.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Update OMAP OneNAND mapping file using device driver model
- Remove board specific macro and values.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
OneNAND is a new flash technology from Samsung with integrated SRAM
buffers and logic interface.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove support for virtual blocks, which are build by
concatenation of multiple physical erase blocks.
For more information please read the MTD mailing list thread
"[PATCH] remove support for virtual blocks"
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We don't want to call dump_cpu_info() from cpu_init() after boot since
it produces a lot of unnecessary noise - since cpu_init() gets called
on resume and hotplug cpu insertion events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When data starts from the beginning of NAND page, 'len' must be zero, not
c->wbuf_page.
Thanks to Zoltan Sogor for reporting this problem.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.
Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some new ipr adapters do not support some of the initialization
commands currently sent to it from the driver. Handle these
commands failing and continue on with the adapter initialization.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While this might be useful for all supported flash types, it is mandatory
for proper JFFS2 support with Sibley flash.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This updates the Primary Vendor-Specific Extended Query parsing to
version 1.4 in order to get the information about the Configurable
Programming Mode regions implemented in the Sibley flash, as well as
selecting the appropriate write command code.
This flash does not behave like traditional NOR flash when writing data.
While mtdblock should just work, further changes are needed for JFFS2 use.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Support now exists in some ipr adapters to issue a device reset
to an Advanced Function disk.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This includes improved error handling/reporting plus some other
message cleanups.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
New ipr adapters support a new device queueing model in the
adapter firmware. The queueing model is the NACA queueing model,
but it does not mean use of NACA is required. The new model removes
some of the adapter firmware queue state that made handling QERR=0
almost impossible. The queueing model on older adapters included the
concept of a queue frozen state, which would freeze the response
queue in the adapter when a check condition occurred, requiring a
a primitive to resume the queue. The new queueing model removes this
complexity.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle some new types of ipr errors that can be returned by the adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some newer ipr adapters are capable of returning autosense from
devices that support it. This patch adds the data structures for
the autosense buffer.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some ipr adapters will automatically create single device
RAID 0 arrays for all unconfigured RAID capable devices found
at adapter initialization time. This patch adds a module parameter
to disable this behavior.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some IPR RAID adapter will automatically create single device RAID arrays
for all attached devices when the card is initialized. Setting the
RUNTIME_RESET doorbell bit will prevent this from occurring, since we
only want this behavior the first time the card is initialized and not
each time the card happens to get reset.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for handling some new errors that may be returned
by ipr adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If an ipr adapter repeatedly fails its initialization
the ipr driver will take the adapter offline and never talk
to it again. This provides a method for the user to manually
try the initialization again through sysfs.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the write buffer command that is issued to the ipr adapter
to update its microcode fails for some reason, the DMA buffer
will never get unmapped. Move the pci_map/unmap out of the
IOA reset job so that the buffer is always clearly mapped
and unmapped.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds a scsi_host sysfs attribute and module parm to enable/disable
the write cache on an ipr adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Optimize ipr's slave_alloc to return -ENXIO for devices that
do not exist.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set the no_uld_attach for devices ipr does not want
upper layer drivers to attach to. These devices are
only reported for RAID management and only sg should
be used to talk to them.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix ipr to include all disks in the supported device list,
not just disks formatted to advanced function format.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify error logging path, sanitize error length returned
by the adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Better handle errors received which are not known to the device driver.
Just dump the hex data so that we have a hope of figuring out what
went wrong.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The generic ipr adapter error log currently logs 2 lines of useless
data. Delete these lines.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IPR RAID arrays show up on a virtual scsi bus, with a scsi bus number
of 255, which is generated by the adapter microcode. For the initial
scan of the host, we manually scan this bus since it does not obey
SAM in regards to sparse LUNs and the disk array devices do not have
a consistent product id to use scsi core's blacklist. If /proc/scsi/scsi
or sysfs is used to delete one of these devices, the device will not
be able to get added back by rescanning the host since scsi core
will see ipr's max_channel as 4, rather than 255. Update max_channel
after the initial scan so that ipr raid arrays can get re-added
if they get deleted.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI qlogicisp driver is both marked BROKEN and superseded by the
qla1280 driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the adapter lock in megaraid_queue. Additional benefit is
that we can get rid of the awkward conditional locking in
mega_internal_command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
also remove the adapter->host_lock alias for adapter->lock and remove
some superflous locking aswell as removing the tiny locking wrappers
for the EH routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
recent kernels call the eh_ methods without the host lock held.
megaraid_sas doesn't need it but drops it before calling a sleeping
routine and reqcquires it afterwards. Just remove the
spin_unlock/spin_lock calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_send_eh_cmnd currently uses a semaphore and an overload of eh_timer
to either get a completion for a command for a timeout.
Switch to using a completion and wait_for_completion_timeout to simply
the code and not having to deal with the races ourselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function has been superceeded by the block request based interfaces
and is unused (except for the uncompilable cpqfc driver).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
now that the abuse in qla2xxx is gone this field can be remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
adjust comments, remove a useless cast and remove a write-only variable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=160868
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
Signed-off-by: Willem Riede <wrlk@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IBM has finally agreed that the "Version Matching" between firmware and
drivers ( and the resulting warning messages ) is no longer necessary.
This patch will remove those functions from the ServeRAID driver.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Update raid class to use nested classes for raid components (this will
allow us to move to a component control model now)
- Make the raid level an enumeration rather than and int.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's an oops that sometimes shows up with SCSI transport classes in
sysfs_hash_and_remove. The problem is that now, because of the class to
device and vice versa symlinks, all classes have to be removed from
visibility *before* the device is removed from visibility.
The transport class trigger points violate this, so bring them back into
conformance.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of building fragtree starting from node with the smallest version
number, start from the highest. This helps to avoid reading and checking
obsolete nodes.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace the D1(printk()) style debugging with the new debug macros
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move functions to read inodes into readinode.c
Move functions to handle fragtree and dentry lists into nodelist.[ch]
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename functions to a name matching the functionality.
Remove stall debug code
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Various simplifiactions. printk format corrections.
Convert more code to use the new debug functions.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When JFFS22 is unable to read the root inode, the bad root inode object is not
freed and remains sticked in the jffs2_i slab cache. When we further try to
free the slab cache (e.g., on rmmod jffs2), slab allocator subsystem panics.
Fix this bug.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If debugging is disabled, define debugging functions as empty macros, instead
of using Dx() explicitly.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
JFFS2 uses f->dents to store the pointer to the symlink target string (in case
the inode is symlink). This is somewhat ugly to use the same field for
different reasons. Introduce distinct field f->target for this purpose.
Note, f->fragtree, f->dents, f->target may probably be put in a union.
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move debug functions into a seperate source file
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Patch from Richard Purdie
Update the PXA pm.c file to allow machines (such as the Sharp
Zaurus) to override the standard pm functions but reuse/wrap them
where needed.
The init call is made slightly earlier to give machine code an init
level to override them in removing any race.
Signed-off-by: Richard Purdie
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since we know the value of cpsr on entry, we can replace the bic+orr with
a single eor. Also remove a possible result delay (at least on XScale).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Make the uengine loader use ixp2000_reg_wrb in the right places.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch fixes AHB/PCI endianness problems when the
processor is in little-endian mode.
The patch configures the CSR register closely following the directives
in [1], paragraph 4.1, page 19.
According to the considerations in [1], page 11, while the AHB bus
supports both endian modes, on the IXP4XX it always uses big-endian.
The PCI bus is connected to the South AHB. A wrong setting in the CSR
register will thus cause a malfunctional PCI bus.
A schematic diagram of the bus interconnections on the IXP4XX
can be found in [1], page 18.
The patch has been verified to work on the NSLU2 in
both LE and BE modes.
The author is Peter Korsgaard.
[1] Intel IXP4XX Product Line of Network Processors and IXC1100
Control Plane Processor:
Understanding Big Endian and Little Endian Modes
http://www.intel.com/design/network/applnots/25423701.pdf
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs.
Signed-off-by: Dirk Opfer
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Than Ngo <than@redhat.com>
qt as installed on fedora core (2 and 3) does not work with vanilla
kernel. The linker fails to locate the qt lib:
Actual Results: # make xconfig
HOSTLD scripts/kconfig/qconf
/usr/bin/ld: cannot find -lqt
collect2: ld returned 1 exit status
Than Ngo has provided following fix for the bug.
Cc: Than Ngo <than@redhat.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Include autoconf.h into every kernel compilation via the gcc command line
using -imacros. This ensures that we have the kernel configuration
included from the start, rather than relying on each file having #include
<linux/config.h> as appropriate. History has shown that this is something
which is difficult to get right.
Since we now include the kernel configuration automatically, make
configcheck becomes meaningless, so remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch creates a file airo.h containing prototypes of the global
functions in airo.c used by airo_cs.c .
If you got strange problems with either airo_cs devices or in any other
completely unrelated part of the kernel shortly or long after a airo_cs
device was detected by the kernel, this might have been caused by the
fact that caller and callee disagreed regarding the size of the first
argument to init_airo_card()...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refine bnx2_poll() logic to write back the most up-to-date status tag
when all work has been processed. This eliminates some occasional
extra interrupts when a older status tag is written even though all
work has been processed.
The idea is to read the status tag just before exiting bnx2_poll() and
then check again for any new work. If no new work is pending, the
status tag written back will not generate any extra interrupt. This
logic is similar to the changes David Miller did to tg3_poll().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically determine the shared memory location where eeprom
parameters are stored instead of using a fixed location.
Add speed reporting to management firmware. This allows management
firmware to know the current speed without contending for MII
registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5708 copper and serdes basic support, including 2.5 Gbps support
on 5708 serdes. SPEED_2500 is also added to ethtool.h
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch I sent in ("prism54: Free skb after disabling
interrupts") included a redundant NULL assignment. Thanks to Herbert
Xu for pointing it out.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems dmascc_setup() is a leftover time before dmascc_init() was
there.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global functions:
- e1000_hw.c: e1000_mc_addr_list_update
- e1000_hw.c: e1000_read_reg_io
- e1000_hw.c: e1000_enable_pciex_master
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
my patch "x86: initialise tss->io_bitmap_owner to something" (commit ID
d5cd4aadd3) introduced a problem with a
program (DOSEMU) that called ioperm after already doing some port i/o.
The problem is that a process switch return causes tss->io_bitmap_base
to be set to IO_BITMAP_OFFSET so that the fault (that *really* sets the
io bitmap) never triggers.
This fixes that regression.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch randomizes the port selected on bind() for connections
to help with possible security attacks. It should also be faster
in most cases because there is no need for a global lock.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
When sk_stream_wait_connect detects a state transition to ESTABLISHED
or CLOSE_WAIT prior to it going to sleep, it will return without
calling finish_wait and decrementing sk_write_pending.
This may result in crashes and other unintended behaviour.
The fix is to always call finish_wait and update sk_write_pending since
it is safe to do so even if the wait entry is no longer on the queue.
This bug was tracked down with the help of Alex Sidorenko and the
fix is also based on his suggestion.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Add a version string to help support issues.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Change netem to support packets getting reordered because of variations in
delay. Introduce a special case version of FIFO that queues packets in order
based on the netem delay.
Since netem is classful, those users that don't want jitter based reordering
can just insert a pfifo instead of the default.
This required changes to generic skbuff code to allow finer grain manipulation
of sk_buff_head. Insertion into the middle and reverse walk.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Some visually impaired people use hardware devices which directly read
the vga screen. When newt for instance asks to hide the cursor for
better visual aspect, the kernel puts the vga cursor out of the screen,
so that the cursor position can't be read by the hardware device. This
is a great loss for such people.
Here is a patch which uses the same technique as CUR_NONE for hiding the
cursor while still moving it.
Mario, you should apply it to the speakup kernel for access floppies
asap. I'll submit a 2.4 patch too.
Signed-off-by: samuel.thibault@ens-lyon.org
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Statically allocated devices in module data is a potential cause
of oopsen. The device may be in use by a userspace process, which
will keep a reference to the device. If the module is unloaded,
the module data will be freed. Subsequent use of the platform
device will cause a kernel oops.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Re-jig the simple platform device support to allow private data
to be attached to a platform device, as well as allowing the
parent device to be set.
Example usage:
pdev = platform_device_alloc("mydev", id);
if (pdev) {
err = platform_device_add_resources(pdev, &resources,
ARRAY_SIZE(resources));
if (err == 0)
err = platform_device_add_data(pdev, &platform_data,
sizeof(platform_data));
if (err == 0)
err = platform_device_add(pdev);
} else {
err = -ENOMEM;
}
if (err)
platform_device_put(pdev);
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduces a new flag TC_RED_HARDDROP which specifies that if ECN
marking is enabled packets should still be dropped once the
average queue length exceeds the maximum threshold.
This _may_ help to avoid global synchronisation during small
bursts of peers advertising but not caring about ECN. Use this
option very carefully, it does more harm than good if
(qth_max - qth_min) does not cover at least two average burst
cycles.
The difference to the current behaviour, in which we'd run into
the hard queue limit, is that due to the low pass filter of RED
short bursts are less likely to cause a global synchronisation.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Adds a new u8 flags in a unused padding area of the netlink
message. Adds ECN marking support to be used instead of dropping
packets immediately.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Removes unnecessary includes, initializers, and simplifies
the code a bit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Since we are no longer depending on the default VQ to be always
allocated we can leave it up to the user to actually create it.
This gives the user the ability to leave it out on purpose and
enqueue packets directly to the device without applying the RED
algorithm.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Introduces a new red parameter set for use in equalize mode,
although only the qavg variable and the idle period marker are
being used for now this makes it possible to allow a separate
parameter set to be used for equalize later on.
The use of this separate parameter set fixes a bogus start of
an idle period in gred_drop() which did start an idle period
on the default VQ even if equalize mode was disabled.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The case when the default VQ is not set up yet is already handled
in a less error prone way.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Try to enqueue packets if we cannot associate it with a VQ, this
basically means that the default VQ has not been set up yet.
We must check if the VQ still exists while requeueing, the VQ
might have been changed between dequeue and the requeue of the
underlying qdisc.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Adds a transformation function returning the DP index for a
given skb according to its tc_index.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Qdiscs are not supposed to reset statistics in reset() and while
changing parameters. My argumentation is that if the user wants
the counters to be reset he can simply remove and readd the
qdiscs, that's what most users do anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Simplifies code a lot by separating the red algorithm and the
queueing logic. We now differentiate between probability marks
and forced marks but sum them together again to not break
backwards compatibility.
This brings GRED back to the level of RED and improves the
accuracy of the averge queue length calculations when stab
suggests a zero shift.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Introduces a function gred_change_vq() acting as a central point
to change VQ parameters. Fixes priority inheritance in rio mode
when the default DP equals 0. Adds proper locking during changes.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Introduces a function gred_change_table_def() acting as a central
point to change the table definition.
Adds missing validations for table definition: MAX_DPs > DPs > 0
and def_DP < DPs thus fixing possible invalid memory reference
oopses. Only root could do it but having a typo crashing the
machine is a bit hard.
Adds missing locking while changing the table definition, the
operation of changing the number of DPs and removing shadowed VQs
may not be interrupted by a dequeue.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Avoids the allocation of a buffer by appending the VQs directly
to the skb and simplifies the code by using the appropriate
message construction macros.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Introduces a flags variable using bitops and transforms eqp to use
it. Converts the conditions of the form (wred && rio) to (wred)
since wred can only be enabled in rio mode anyway.
The patch also improves WRED mode detection. The current behaviour
does not allow WRED mode to be turned off again without removing
the whole qdisc first. The new algorithm checks each VQ against
each other looking for equal priorities every time a VQ is changed
or added. The performance is poor, O(n**2), but it's used only
during administrative tasks and the number of VQs is strictly
limited.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Removes the skb trimming code which is not needed since we never
touch the skb upon failure. Removes unnecessary includes,
initializers, and simplifies the code a bit. Removes Jamal's
obsolete email addresses upon his own request.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
We should not interrupt and restart an idle period while idling already.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Simplifies code a lot by separating the red algorithm and the
queueing logic. We now differentiate between probability marks
and forced marks but sum them together again to not break
backwards compatibility.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Changes IP_ECN_set_ce() and IP6_ECN_set_ce() to return 0 if the CE
bits could not bet set because none of the ECT bits are set or 1
if the CE bits are already set or have been successfully set.
Introduces INET_ECN_set_ce(skb) to enable CE bits for all supported
protocols.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Extracts the RED algorithm from sch_red.c and puts it into include/net/red.h
for use by other RED based modules. The statistics are extended to be more
fine grained in order to differ between probability/forced marks/drops.
We now reset the average queue length when setting new parameters, leaving
it might result in an unreasonable qavg for a while depending on the value of W.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Adds a phy_mask field to struct mii_bus and uses it. This field
indicates each phy address to be ignored when probing the mdio bus.
This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some boards using the 79c976 pcnet32 chip will hang the system if the
ethtool --register-dump is performed with the device operational. The
request to read bcr30 is retried by the PCI device infinitely without
returning data, hanging the system.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch is a better fix for Allied Telesyn 2700/2701 FX boards than
the change made in early January this year. It allows the user to
select the speed/duplex via module_param, but if no selection is made,
forces the speed to 100 FD. It fixes both Bugzilla bugs 2669 and 4551.
Tested ia32 and ppc64 by myself, and by the originator of bug 2669.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Display the name eth%d or pci_name() of device which fails to allocate
memory. When changing ring size via ethtool, it also releases the
lock before returning on error. Added comment that the caller of
pcnet32_alloc_ring must call pcnet32_free_ring on error, to avoid leak.
Tested ia32 by forcing allocation errors.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides updated documentation on the Neterion(S2io) driver.
Please review the patch.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=2
This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=3
Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
fid is declared as a u32 (unsigned int), and then a few lines later, it is checked for a value < 0, which is clearly useless.
In the two locations this function is used, in one it is *explicitly* given a negative number, which would be ignored with the
current definition.
Thanks to LinuxICC (http://linuxicc.sf.net).
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Convert netem to use PSCHED_LESS and warn if requeue fails.
With some of the psched clock sources, the subtraction doesn't
work always work right without wrapping.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
With the new nf_queue generalization in 2.6.14, we've introduced a bug
that causes an oops as soon as a packet is queued but no queue handler
registered. This patch fixes it.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
There's a missing dependency from the CONNMARK target to ip_conntrack.
Signed-off-by: Pablo Neira Ayuso <pablo@eurodev.net>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Currently the driver takes a reference only for requests coming by way
of the gendisk, not for requests coming by way of the struct device or
struct scsi_device. Such requests can arrive in the rescan, flush,
and shutdown pathways.
The patch also makes the scsi_disk keep a reference to the underlying
scsi_device, and it erases the scsi_device's pointer to the scsi_disk
when the scsi_device is removed (since the pointer should no longer be
used).
This resolves Bugzilla entry #5237.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The printks that aren't for debugging should use the name of the controller,
not the driver name. Multiple MMC controllers aren't that common today, but
this is the right way to do things.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- egcs is not supported by kernel 2.6
- gcc 3.3 seems to be a good choice on ARM
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a broken if clause in the wbsd driver that can cause the
driver to try and configure the chip even though none is found. This
results in i/o on invalid ports.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Report the device's real page size capability in mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The unknown protocol is used as a fallback when a protocol isn't known.
Hence we cannot handle it failing, so don't set ".me". It's OK, since we
only grab a reference from within the same module (iptable_nat.ko), so we
never take the module refcount from 0 to 1.
Also, remove the "protocol is NULL" test: it's never NULL.
Signed-off-by: Rusty Rusty <rusty@rustcorp.com.au>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
This adds support for the Nvidia Geforce 7800 series of cards to the
nvidiafb framebuffer driver. All it does is add the PCI device id for
the 7800, 7800 GTX, 7800 GO, and 7800 GTX GO cards to the module device
table for the nvidiafb.ko driver, so that nvidiafb.ko will actually work
on these cards.
I also added the relevant PCI device ids to linux/pci_ids.h
I tested it on my 7800 GTX here and it works like a charm. I now can
get framebuffer support on this card! Woo hoo!! Nothing like 200x75 text
mode to make your eyes BLEED. ;)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This endianness bug slipped through while changing the 'gre.key' field in the
conntrack tuple from 32bit to 16bit.
None of my tests caught the problem, since the linux pptp client always has
'0' as call id / gre key. Only windows clients actually trigger the bug.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
We can't currently use asm-ppc/page.h in vmlinux.lds.S, so until
we have a merged page.h, define PAGE_SIZE and KERNELBASE locally.
Also gets rid of some dynamic executable cruft that we had for
32-bit. With -Ttext=$(KERNELBASE) this didn't cause any problem,
but when we changed to putting . = KERNELBASE in the vmlinux.lds.S
this cruft caused the text to get linked at 0xa0 instead of
0xc0000000. Oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also moves setup_cpu_maps to setup-common.c (calling it
smp_setup_cpu_maps) and uses it on both 32-bit and 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix some dprintk's so that NLM, NFS client, and RPC client compile
cleanly if CONFIG_SYSCTL is disabled.
Test plan:
Compile kernel with CONFIG_NFS enabled and CONFIG_SYSCTL disabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The sunrpc module should build properly even when CONFIG_SYSCTL is
disabled.
Reported by Jan-Benedict Glaw.
Test plan:
Compile kernel with CONFIG_NFS as a module and built-in, and CONFIG_SYSCTL
enabled and disabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that we have a method of dealing with delegation recalls, actually
enable the caching of posix and BSD locks.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Delegations allow us to cache posix and BSD locks, however when the
delegation is recalled, we need to "flush the cache" and send
the cached LOCK requests to the server.
This patch sets up the mechanism for doing so.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I missed this one... Any form of rename will result in a delegation
recall, so it is more efficient to return the one we hold before
trying the rename.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RFC 3530 states that for OPEN_DOWNGRADE "The share_access and share_deny
bits specified must be exactly equal to the union of the share_access and
share_deny bits specified for some subset of the OPENs in effect for
current openowner on the current file.
Setattr is currently violating the NFSv4 rules for OPEN_DOWNGRADE in that
it may cause a downgrade from OPEN4_SHARE_ACCESS_BOTH to
OPEN4_SHARE_ACCESS_WRITE despite the fact that there exists no open file
with O_WRONLY access mode.
Fix the problem by replacing nfs4_find_state() with a modified version of
nfs_find_open_context().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We must not remove the nfs4_state structure from the inode open lists
before we are in sequence lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
At header fixup time, it is not yet legal to ioremap() PCI
device registers, yet that is what this quirk code needs to
do.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not transfer remaining time slice to another cpu on process exit.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Nicolas Pitre
We have an optimized sha1 routine (arch/arm/lib/sha1.S) meant to
override the generic one in lib/sha1.c.
Unfortunately lib/lib.a is listed _before_ arch/arm/lib/lib.a in the
link argument list and therefore the architecture specific lib functions
are not picked up before the generic versions.
This patch is a quick fix to change that ordering for ARM. Here's what
the kbuild maintainer had to say about it (was also CC'd on lkml):
On Wed, 2 Nov 2005, Sam Ravnborg wrote:
> This looks like an obvious way to achive correct ordering.
> We could change it so arch defines always took precedence but
> the above is so simple that it is not worth the effort.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add platform devices for flash to Lubbock and Mainstone board files.
Once in place, the two existing mtd map drivers for the boards will be
converted to use a single pxa2xx map driver in the linux-mtd tree.
Take 4: flash_platform_data .map_name vs. .name cleaned up, resync with
merged irda patch context.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Jiang
This provides support for IXP2xxx error interrupt handling. Previously there was a patch to remove this (although the original stuff was broken). Well, now the error bits are needed again. These are used extensively by the micro-engine drivers according to Deepak and also we will need it for the new EDAC code that Alan Cox is trying to push into the main kernel.
Re-submit of 3072/1, generated against git tree pulled today. AFAICT, this git tree pulled in all the ARM changes that's in arm.diff. Please let me know if there are additional changes. Thx!
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
ARM processors that have pld instructions are not using those copy_user
implementation anymore. Let's remove the useless PLD lines which were
half wrong anyway.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modules: HDA Codec driver,HDA generic driver
- Make bound controls global to all patches
- Clean up analog patches (for the upcoming extension to AD1988)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
If we submit all our URBs when a playback stream is started, the first
hwptr_done update for each URB happens at the same time. This results
in an underrun when there isn't enough PCM data available at this
point for all URBs.
To avoid this, we begin submitting our URBs earlier (when the stream
is prepared), with empy packets. When the stream is started, the
prepare_playback_urb() call for each URB will be run only when the
respective URB has completed previously, so the first hwptr_done
updates will be done nicely staggered.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: MIPS AU1x00 driver
AMD Au1x00 ALSA driver fails compilation with the alternate spinlock
implementation because it doesn't do locking/unlocking correctly in some
places (passes spinlock by value).
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
It appears that either the Audigy DMA engine or the Linux kernel cannot
handle 32 bit DMA with this device. Problem manifests as noise when
using more than 2GB of RAM, possibly only on 64 bit machines.
The OSS driver actually uses a 29 bit DMA mask for both devices, this
seems like overkill for now.
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AZT3328 driver
this is now an even much more reworked patch (#3) for my azt3328.c ALSA driver.
IOW I spent another 4 evenings to get the sequencer timer to work properly
(my head is still hurting) and do lots of other cleanups.
Note that despite the extensive sequencer timer additions, the driver object
is still only 2kB bigger than the previous version, due to those many
optimizations...
Changes in version #3:
- fully working ALSA sequencer timer support for the card's 1024000Hz
DirectX timer (downscaling adjustable via seqtimer_scaling module param)
- an insane amount of code optimizations
- many, many cleanups
Changes in version #2:
- FOUND the 1us DirectX timer area (yay!), made the code respect it
properly
- renamed some 'weird' mixer control names according to ControlNames.txt
- cleanup unneeded debug messages, reformatting
- improved I/O register documentation
- constified many more structs
Changes in version #1:
- improves/fixes some fatal playback/recording interaction
- improves IRQ handler performance (and actually fixes some weird code)
- coalesces some I/O accesses
- slightly improves I/O interface documentation
- improves/fixes logging
- defines out some less important debug code
- constifies some data
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver,Common EMU synth
This patch fixes problems with voices cutting off or not
sounding at all.
Signed-off-by: Tim <tedon@rogers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HWDEP Midlevel,PCM Midlevel,RawMidi Midlevel,ALSA Core
Replace usage of CONFIG_SND_MAJOR with snd_major, where appropriate.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA Core,ALSA Minor Numbers
Remove the unused and undefined symbols SNDRV_DEVICE_TYPE_{MIXER,
PCM_PLOOP,PCM_CLOOP}, and introduce a new symbol SNDRV_MINOR_GLOBAL
for non-card-specific devices like the sequencer or the timer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: AD1889 driver,RME9652 driver
This is the sound/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in sound/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
1.In intel8x0_measure_ac97_clock routine, when stop DMA, there is not stop
DMA corectly, but start another PCM In2 DMA engine.
2.In do_ali_reset routine, there is only need to enable PCM IN and PCM OUT.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: Documentation,ALI5451 driver,NM256 driver
Removed multi-card supports for ali5451 and nm256 drivers.
They are supposed to be a single device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: NM256 driver
The current snd-nm256 driver can cause Dell Latitude CSx laptops to
lock-up during module (un)load. I have isolated this to the writes to
the control port register at offset 0x6cc which were not already
protected by the existing reset_workaround.
I tried grouping these writes with the existing reset_workaround
clause, but that caused the driver to have (un)load problems on the
Dell Latitude LS laptops. So, I have implemented a reset_workaround_2
clause (please feel free to suggest a better name!) to cover this
situation and added a quirk entry for the CSx laptops.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
When no default timer frequency has been set, initialize_timer() just
uses the maximum frequency supported by the timer, which is ridiculously
high on 96 kHz timers.
This patch introduces a default frequency of 1000 Hz for this case, and
makes sure that a frequency set by the user isn't too high.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
- Set buggy_irq parameter before registration of irq handler.
- Clean up module parameter handling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: VIA82xx driver
The change only affects the via823x kind of chips.
Here the via8233_pcm_pointer_hw() function
(named snd_via8233_pcm_pointer() before)
needed to loop until a non zero position is red from the chip.
Measurements have shown that more than 200 loops are typically needed on
an Athlon64.
As io-reads cost many cycles, those loops sum up huge.
via8233_pcm_pointer_hw() runs either in interrupt or with interrupts
disabled. So it introduces significant interrupt latency.
The patch introduces a calculated position value hwptr_done,
that is updated by the interrupt routine when a period is completed.
It is only used, if the 823x chip returns a zero position, which can't
be interpreted reliably.
Further optimisation is applied on the 8233 chip's interrupt routine:
Only the SGD_SHADOW is read, as it contains all infos needed.
We ommit ~5 more register reads that way.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Remove the usb_reset_configuration() call from the probe callback
because it isn't needed and it may interfere with other drivers
already loaded for the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: VIA82xx driver
The patch enable separate DXS controls of sound function of VIA VT82xx
controller in case DXS volume is not needed for PCM Playback volume
control emulation.
Signed-off-by: Honza Maly <hkmaly@matfyz.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,MIPS AU1x00 driver,PPC Beep,SPARC DBRI driver
Removed the use of chip_t, which was obsoleted.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Timer Midlevel
Split or rewrite lines that are longer than 80 characters, and remove
whitespaces at the end of lines.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Timer Midlevel
The return value of list_entry() already has the type from the second
argument, so we don't need to typecase it again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver,Timer Midlevel
Add a module pointer to the timer structure and use it for refcounting
instead of the card's module pointer to prevent the global timer
modules (rtctimer and hpetimer) from being removed while in use.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ES1938 driver
- Clean up the last PM fix
- Add TRIGGER_SUSPEND/RESUME to disable/enable DMA properly during PM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES1938 driver
This patch fixes the suspend/resume issue I'm having with ESS-Solo1
soundcard. Without this patch I might get after resume message
that kernel is disabling the IRQ5 (soundcard). If there was something
playing it wont continue after resume without this patch.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA Core,ALSA<-OSS emulation
Remove a global function snd_task_name(), and move it local
to snd-pcm-oss module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,PCM Midlevel,Timer Midlevel,ALSA Core
Use the standard getnstimeofday() function instead of ALSA's own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
On my Acer Aspire 3003LCi laptop, the speaker volume is not controlled
by the master control, but by the headphone control. Enabling the
'hp_only' quirk corrects this. The patch below adds this device to the
list of known quirks.
Signed-off-by: Dick Streefland <dick@streefland.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1724 driver
Remove the restcition of sample rates on Revolution 7.1 board.
This enables the low 8-44kHz sample rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Sound Core,PCI drivers
AC97 Kconfig entries broke the ALSA device drivers menu,
so move them to a location where that won't happen,
enabling all device sub-menus to be presented together.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch cleans last ac97 audio/modem codec interception in
initialization procedures (ac97_mixer_new()) and removes obsolete
SHARED_TYPE 'locking' which prevents from AMC codecs to function
correctly.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
This patch adds a new mixer control called 'IEC958 Loop' which makes
it possible to loop digital signals from S/PDIF-in to S/PDIF-out.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: ALSA sequencer
Remove the last parameter of snd_seq_timer_set_tick_resolution()
because it is always one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver
The check whether rtctimer_freq is a power of two can be done easier
with a simple bit operation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: RTC timer driver
The rtc_inc variable is never used outside the interrupt handler, and
is always one where it matters, so we can just remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Move the usb_complete_callback() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Move the usb_pipe_needs_resubmit() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add more comments about other device modes and unsupported devices to
the Roland part of the quirks table.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Simplify the handling of MIDI quirks by treating an interface without
quirks as a QUIRK_MIDI_STANDARD_INTERFACE.
This also fixes the bug where a MIDI_STANDARD quirk would not be
recognized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: CMIPCI driver
If possible, use ports in the card's PCI port address range instead of
the legacy ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Intel driver
This patch is to make the Intel HDA code work for NVIDIA azalia controller.
Modified by Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod G. <vinodg@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
Adds left and right front channel outputs using fxbus 8 and 9 and 'Front'
playback and capture volume controls.
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the recent reorg of the io scheduler selection, it unfortunately
became possible to select an io scheduler to be the default even if it
wasn't builtin. Fix this by requiring the default scheduler to be
builtin.
Signed-off-by: Jens Axboe <axboe@suse.de>
drivers/block/ is right now a mix of core and driver parts. Lets move
the core parts to a new top level directory. Al will move the fs/
related block parts to block/ next.
Signed-off-by: Jens Axboe <axboe@suse.de>
The merged verison of ELF_CORE_COPY_REGS is basically the PPC64 version, with
a memset that came from PPC and a few types abstracted out into #defines. But
it's not _quite_ right.
The first problem is we calculate the number of registers with:
nregs = sizeof(struct pt_regs) / sizeof(ELF_GREG_TYPE)
For a 32-bit process on a 64-bit kernel that's bogus because the registers are
64 bits, but ELF_GREG_TYPE is u32, so nregs == 88 which is wrong.
The other problem is the memset, which assumes a struct pt_regs is smaller
than a struct elf_regs. For a 32-bit process on a 64-bit kernel that's false.
The fix is to calculate the number of regs using sizeof(unsigned long), which
should always be right, and just memset the whole damn thing _before_ copying
the registers in.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
There's no reason for smp_release_cpus() to be asm, and most people can make
more sense of C code. Add an extern declaration to smp.h and remove the custom
one in machine_kexec.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Restrict CONFIG_SGI_SN_XP to IA64_GENERIC or IA64_SGI_SN2 kernels.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make sure that the P_Key index passed into mthca_modify_qp() is
within the device's P_Key table.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wrap_mmu_context(), delayed_tlb_flush(), get_mmu_context() all
have an extra { } block which cause one extra indentation.
get_mmu_context() is particularly bad with 5 indentations to
the most inner "if". It finally gets on my nerve that I can't
keep the code within 80 columns. Remove the extra { } block
and while I'm at it, reformat all the comments to 80-column
friendly. No functional change at all with this patch.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Nicolas Pitre
Using a llx format to print addresses that might possibly be (only) 36
bits wide make sense. However making it a zero padded 16 char wide
field is a bit excessive and useless.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we do not invalidate TLBs/caches on MM switches, we should not
clear the cpu_vm_mask for the CPU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix hotplug of devices for ib_umad module: when a device goes away,
kill off all MAD agents for open files associated with that device,
and make sure that the device is not touched again after ib_umad
returns from its remove_one function.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 'K' extension adds several new instructions to the ARMv6 ISA
which are primerily useful for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
register_vpa() doesn't actually do a VPA register call it just uses the flags
you pass it, so rename it to vpa_call() to be clearer.
We can then define register_vpa() and unregister_vpa() which are both simple
wrappers around vpa_call(). (we'll need unregister_vpa() for kexec soon)
We can then cleanup vpa_init(), and because vpa_init() is only called from
platforms/pseries we remove the definition in asm-ppc64/smp.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Mellanox has decided that the components of the firmware version are
really meant to be displayed in decimal, e.g. 0x000400070190 is
version 4.7.400. Change the format we use from "%x.%x.%x" to
"%d.%d.%d" to match this convention.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a few places already, and soon will be more, where we synthesise
branch instructions at runtime. Rather than doing it by hand in each case,
it would make sense to have one implementation.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Oops, replacing the two u64s in struct ipc64_perm with __u32s changed
the alignment of that structure, which could mess up userspace.
Revert to using two unsigned long longs (which is what ppc32 had
originally). ppc64 orignally had two unsigned longs, but long long is
the same size on 64 bit, so this should be ok there too.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds missing header and thus fix the warning issued by ming prototype.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there is no Kconfig symbol to indicate that we want nvram
support on 64-bit kernels; it's assumed we always want it, so make
the powermac setup code always initialize the pmac nvram code if
64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The latest updates to bug.h generate build warnings in traps.c in
arch/ppc. Fix print format specifiers to account for change of line type
to long from int.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The extraction of PCI stuff from struct device_node left some false
assumptions in notifier code. As a result, dynamic add crashes when
non-PCI nodes are added. This patch fixes these assumptions.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we set the kernel entry point and the address of the text
section in the Makefile, using CONFIG_KERNEL_START.
But we've already got <asm/page.h> in the linker script, so we can just
use KERNELBASE directly. That means if we ever change KERNELBASE there's
one less place to change it.
And we can set the entry point with ENTRY().
There are zero differences from "readelf -a vmlinux" with or without this
patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Don't build ipoib_mcast_iter_ functions if CONFIG_INFINIBAND_IPOIB_DEBUG
is not enabled -- their only callers will not be built either.
Also move the prototype for ipoib_open() to ipoib.h to fix a sparse warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's some debugging in prom.c that wraps nastly on 80 character
terminals, reformat it to fit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Merge include/asm-ppc/kexec.h and include/asm-ppc64/kexec.h.
The only thing that's really changed is that we now allocate crash_notes
properly on PPC32. It's address is exported via sysfs, so it's not correct
for it to be a pointer.
I've also removed some of the "we don't use this" comments, because they're
wrong (or perhaps were referring only to arch code).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move plpar_wrappers.h into arch/powerpc/platforms/pseries, fixup white space,
and update callers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Move pSeries specific code in set_dabr() into a ppc_md function, this will
allow us to keep plpar_wrappers.h private to platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Make "QoS and/or fair queueing" have its own menu, it's too big to be
inlined into "Network options". Remove the obsolete NET_QOS option.
Automatically select NET_CLS if needed. Do the same for NET_ESTIMATOR
but allow it to be selected manually for statistical purposes. Add
comments to separate queueing from classification. Fix dependencies
and ordering of classifiers. Improve descriptions/help texts and
remove outdated pieces.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Copy default configs into arch/powerpc/configs, rename bpa_defconfig to
cell_defconfig while we're at it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
* Hide debugging code into #ifdef, which allows to simplify
the large switch statement
* Update macros to not reference variables not given as
arguments
Signed-off-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not register statically allocated input devices to prevent
OOPS when attaching input interfaces since it requires class
device to be properly initialized.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes the x86-64 find_[first|next]_zero_bit() function for the
end-of-range case. It didn't test for a zero size, and the "rep scas"
would do entirely the wrong thing.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves rtas-proc.c and rtas_flash.c into arch/powerpc/kernel, since
cell wants them as well as pseries (and chrp can use rtas-proc.c too,
at least in principle). rtas_fw.c is gone, with its bits moved into
rtas_flash.c and rtas.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cannot build XFS filesystem support as module with quota support. It
works only when the XFS filesystem support is compiled into the kernel.
Menuconfig prevents from setting CONFIG_XFS_FS=m and CONFIG_XFS_QUOTA=y.
How to reproduce: configure the XFS filesystem with quota support as
module. The resulting kernel won't have quota support compiled into
xfs.ko.
Fix: Changing the fs/xfs/Kconfig file from tristate to bool lets you
configure the quota support to be compiled into the XFS module. The
Makefile-linux-2.6 checks only for CONFIG_XFS_QUOTA=y.
Signed-off-by: Dimitri Puzin <tristan-777@ddkom-online.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Nathan Scott <nathans@sgi.com>
This is now used to issue a delayed allocation flush before reporting
quota, which allows the used space quota report to match reality.
Signed-off-by: Nathan Scott <nathans@sgi.com>
The recent rewrite of skb_copy_datagram_iovec broke the reception of
zero-size datagrams. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Fix up etherdevice docbook comments and make them (and other networking stuff)
get dragged into the kernel-api. Delete the old 8390 stuff, it really isn't
interesting anymore.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Optimize the match for broadcast address by using bit operations instead
of comparison. This saves a number of conditional branches, and generates
smaller code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
and leaf blocks. The problem cam from xfsqa test 117.
SGI-PV: 940655
SGI-Modid: xfs-linux:xfs-kern:201527a
Signed-off-by: Yingping Lu <yingping@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
The max growth of BIC TCP is too large. Original code was based on
BIC 1.0 and the default there was 32. Later code (2.6.13) included
compensation for delayed acks, and should have reduced the default
value to 16; since normally TCP gets one ack for every two packets sent.
The current value of 32 makes BIC too aggressive and unfair to other
flows.
Submitted-by: Injong Rhee <rhee@eos.ncsu.edu>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
And filter mode is exclude.
Further explanation by David Stevens:
Multicast source filters aren't widely used yet, and that's really the only
feature that's affected if an application actually exercises this bug, as far
as I can tell. An ordinary filter-less multicast join should still work, and
only forwarded multicast traffic making use of filters and doing empty-source
filters with the MSFILTER ioctl would be at risk of not getting multicast
traffic forwarded to them because the reports generated would not be based on
the correct counts.
Signed-off-by: Yan Zheng <yanzheng@21cn.com
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It seems logical.
Note that CONFIG_EXPERIMENTAL itself doesn't enable any code.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Shrink our source and .text a little by removing a few assignments of
NULL and 0 to memory that is already cleared as part of the allocation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace kmalloc()+memset(,0,) with kzalloc(), for a net savings of 35
source lines and about 500 bytes of text.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
fb1c8f93d8 broke the ARM rwlock code since
it only partially updated the rwlock implementation. Properly update it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
3016/1 changed the map_desc structure to take a PFN instead of a
physical address. Fixup Realview machine support for this change.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that without the extra tlb flush, we may end up faulting
during the early kernel initialisation because the TLB can't see
the updated page tables.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from John Bowler
Fix for a compiler warning, this wasn't apparent in 2.6.12, I
believe the compiler options have been changed (somewhere) so
that passing a (void*) to a (u32) argument is now warned.
This accounts for the majority of the warnings in my builds of
the 2.6.14 kernel for NSLU2.
The patch changes pointer parameters declared as u32 to be
declared as either, for read parameters:
const volatile void __iomem *
and for write parameters:
volatile void __iomem *
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include asm/rtas.h for prototype for rtas_call etc., and make the
`done' variable unsigned int since that's what rtas_call wants.
Signed-off-by: Paul Mackerras <paulus@samba.org>
cfq's add_req_fn callback may invoke q->request_fn directly and
depending on low-level driver used and timing, a queued request may be
finished & deallocated before add_req_fn callback returns. So,
__elv_add_request must not access rq after it's passed to add_req_fn
callback.
This patch moves rq_mergeable test above add_req_fn(). This may
result in q->last_merge pointing to REQ_NOMERGE request if add_req_fn
callback sets it but as RQ_NOMERGE is checked again when blk layer
actually tries to merge requests, this does not cause any problem.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a panic in the current tree caused by a race condition between the initial replenish cycle and the rx processing of the first packets trying to replenish the buffers.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/tlclk.c: In function `tlclk_init':
drivers/char/tlclk.c:775: warning: implicit declaration of function `platform_device_register_simple'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This section of code calls .audit_syscal_exit, but is inside CONFIG_AUDIT,
so it will fail to build if CONFIG_AUDITSYSCALL is not defined.
After discussion with David Woodhouse, change the ifdef to
CONFIG_AUDITSYSCALL
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CC drivers/char/tpm/tpm_nsc.o
drivers/char/tpm/tpm_nsc.c:277: error: `platform_bus_type' undeclared here (not in a function)
...
CC drivers/char/tpm/tpm_atmel.o
drivers/char/tpm/tpm_atmel.c:175: error: `platform_bus_type' undeclared here (not in a function)
Make sure to include proper headers.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add reset/reboot code to support the ColdFire 5208 family.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the UARTs on the ColdFire 5208 family.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PIT timer in the 5208 ColdFire has slightly different interrupt
bit definitions than the PIT timer used on other ColdFire parts.
Define the commonly used bit and mask numbers here, and let
part specific defines take precedence if they are defined.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the PIT timer used in the 5208 ColdFire fmaily.
Patch originally from Matt Wadell (from code originally modified by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use board name defines to distinguish boards, instead of combinations
of more generic defines.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the cpu cache of the 5208 ColdFire fmaily.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the internal register map of the 5208 ColdFire fmaily.
Patch originally from Matt Wadell (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define the register space of the new 5208 ColdFire family (which includes
to 5207). It is mostly similar to the other ColdFire parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use board name define to differentiate boards, not combination
of more generic defines.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated m68knommu defconfig. Part of changing the "Motorola" names
to their new name "Freescale".
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unmaintained asm-m68knommu/ide.h. It is completely out of
date - and there is no underlying support for it.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't really understand why gcc gives the error it does, but without
this patch, when building with CONFIG_HOTPLUG=n, I get errors like:
CC arch/x86_64/pci/../../i386/pci/fixup.o
arch/x86_64/pci/../../i386/pci/fixup.c: In function `pci_fixup_i450nx':
arch/x86_64/pci/../../i386/pci/fixup.c:13: error: pci_fixup_i450nx causes a section type conflict
The change is obviously correct: an array should be declared
__devinitdata rather that __devinit.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Martin J. Bligh <mbligh@mbligh.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days, the NACA only exists on iSeries. Therefore, this patch
moves naca.h from include/asm-ppc64 to arch/powerpc/platforms/iseries.
There was one file including naca.h outside of platforms/iseries -
arch/ppc64/kernel/udbg_scc.c. However, that's obviously a hangover
from older days. The include is not necessary, so this patch simply
removes it.
Built and booted on iSeries, built for G5 (which uses udbg_scc.o).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/dart.h is included in exactly one place -
arch/powerpc/sysdev/u3_iommu.c. This patch, therefore, moves it into
arch/powerpc/sysdev. While we're at it, update the #ifndef/#define
protecting the include, and the filename in the comments of
u3_iommu.c.
Built and booted on pSeries and G5, built for ppc32 powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc64 versions of numnodes.h and sparsemem.h can be safely moved
to asm-powerpc with no changes apart from changing the #define to the
standard _ASM_POWERPC_ form. There are no ppc32 versions of these
files, because they only have any effect if CONFIG_SPARSEMEM is
enabled, which it never can be on ppc32.
Built and booted on pSeries (POWER5), built for 32-bit powermac.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This simplifies the macros which are different between 32-bit and
64-bit. It also fixes a couple of printks on the bug->line element,
which is now a long.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Spotted by Roger Willcocks <willcor @at@ gmail.com>
SGI-PV: 944858
SGI-Modid: xfs-linux:xfs-kern:201213a
Signed-off-by: Eric Sandeen <sandeen@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
using xfs rt
SGI-PV: 944632
SGI-Modid: xfs-linux:xfs-kern:200983a
Signed-off-by: Eric Sandeen <sandeen@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
anymore and simplify the final put path a little
SGI-PV: 908809
SGI-Modid: xfs-linux:xfs-kern:200790a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
We were getting powerbook sleep code included, and giving compile
errors, with CONFIG_PM=y on a 64-bit build. This excludes that code
so the kernel will compile. One day BenH will implement on sleep on
the G5...
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of instances of "i" that needed to be changed to "cpu_id"
got missed in the merge, because they were in CONFIG_TAU code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
information gcc could not find out (that a directory always has a ..
entry), the others are outright gcc bugs.
SGI-PV: 943511
SGI-Modid: xfs-linux:xfs-kern:200055a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
The nvram driver imported from the ppc code uses call_rtas, but
rtas_call is the name we are using in merged code (since ppc64 used
that name, and it uses far more RTAS calls than ppc32).
Signed-off-by: Paul Mackerras <paulus@samba.org>
DATA_TYPE is really not a good thing to put into header that
gets included all over the tree...
Just make the cast always (long) and get rid of DATA_TYPE altogether.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges the ppc32 and ppc64 versions of futex.h, essentially
by taking the ppc64 version as the powerpc version. The old ppc32
version did not implement the futex_atomic_op_inuser() callback (it
always returned -ENOSYS), so FUTEX_WAKE_OP would not work on ppc32.
In fact the ppc64 version of this function is almost suitable for
ppc32 as well - the only change needed is to extend ppc_asm.h with a
macro expanding to to the right pseudo-op to store a pointer (either
".long" or ".llong").
Built and booted on pSeries. Built for 32-bit powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oops, when merging ipcbuf.h, I forgot that 'u64' can't be used in
user-visible headers. This patch corrects the problem, replacing the
unused fields with an array of four __u32s.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
the data/attr forks now grow up/down from either end of the literal area,
rather than dividing the literal area into two chunks and growing both
upward. Means we can now make much more efficient use of the attribute
space, incl. fitting DMF attributes inline in 256 byte inodes, and large
jumps in dbench3 performance numbers. It is self enabling, but can be
forced on/off via the attr2/noattr2 mount options.
SGI-PV: 941645
SGI-Modid: xfs-linux:xfs-kern:23837a
Signed-off-by: Nathan Scott <nathans@sgi.com>
the data/attr forks now grow up/down from either end of the literal area,
rather than dividing the literal area into two chunks and growing both
upward. Means we can now make much more efficient use of the attribute
space, incl. fitting DMF attributes inline in 256 byte inodes, and large
jumps in dbench3 performance numbers. It is self enabling, but can be
forced on/off via the attr2/noattr2 mount options.
SGI-PV: 941645
SGI-Modid: xfs-linux:xfs-kern:23836a
Signed-off-by: Nathan Scott <nathans@sgi.com>
the data/attr forks now grow up/down from either end of the literal area,
rather than dividing the literal area into two chunks and growing both
upward. Means we can now make much more efficient use of the attribute
space, incl. fitting DMF attributes inline in 256 byte inodes, and large
jumps in dbench3 performance numbers. It is self enabling, but can be
forced on/off via the attr2/noattr2 mount options.
SGI-PV: 941645
SGI-Modid: xfs-linux:xfs-kern:23835a
Signed-off-by: Nathan Scott <nathans@sgi.com>
filesystems to expose the filesystem stripe width in stat(2) rather than
the page cache size. This allows applications requiring high bandwidth to
easily determine the optimum I/O size for the underlying filesystem. The
default is to report the page cache size (i.e. "nolargeio").
SGI-PV: 942818
SGI-Modid: xfs-linux:xfs-kern:23830a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
replace PBF_NONE with an inverted PBF_DONE, so it's like all the other
flags.
SGI-PV: 942609
SGI-Modid: xfs-linux:xfs-kern:199136a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
writes. In addition flush the disk cache on fsync if the sync cached
operation didn't sync the log to disk (this requires some additional
bookeping in the transaction and log code). If the device doesn't claim to
support barriers, the filesystem has an extern log volume or the trial
superblock write with barriers enabled failed we disable barriers and
print a warning. We should probably fail the mount completely, but that
could lead to nasty boot failures for the root filesystem. Not enabled by
default yet, needs more destructive testing first.
SGI-PV: 912426
SGI-Modid: xfs-linux:xfs-kern:198723a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
reverse startup order
SGI-PV: 942063
SGI-Modid: xfs-linux:xfs-kern:198651a
Signed-off-by: Christoph Hellwig <hch@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
Patch from Deepak Saxena
CONFIG_MACH_GTWX5715 hardcodes the machine type in head-xscale.S so we
can no longer boot on any other machine types. The proper fix would be
to remove the hardcoding, but that machine is an off-the-shelf system
and most users won't have access to the bootloader. :(
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
* If request_irq fails then a call to release_mem_region will be made with an invalid pointer.
* Two formatting fixes
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix structure layouts to ensure same size on 32-bit and 64-bit architectures.
This permits 32-bit userspace apps on a 64-bit kernel.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Patch from Lennert Buytenhek
This patch adds a microcode loader for the ixp2000 architecture.
The ixp2000 is an xscale-based CPU with a number of additional small
CPUs ('microengines') on die that can be programmed to do various
things. Depending on the ixp2000 model, there are between 2 and 16
microengines.
This code provides an API that allows configuring the microengines,
loading code into them, and starting and stopping them and reading
out a number of status registers, and is used by the microengine
network driver that was recently announced to netdev.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a preemption safe implementation of copy_to_user
and copy_from_user based on the copy template also used for memcpy.
It is enabled unconditionally when CONFIG_PREEMPT=y. Otherwise if the
configured architecture is not ARMv3 then it is enabled as well as it
gives better performances at least on StrongARM and XScale cores. If
ARMv3 is not too affected or if it doesn't matter too much then
uaccess.S could be removed altogether.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch provides a new implementation for optimized memory copy
functions on ARM. It is made of two levels: a template that consists of
the core copy code and separate files that define macros to be used with
the core code depending on the type of copy needed. This allows for best
performances while sharing the same core for implementing memcpy(),
copy_from_user() and copy_to_user() for instance.
Two reasons for this work:
1) the current copy_to_user/copy_from_user implementation assumes no
task switch will ever occur in the middle of each copied page making
it completely unsafe with CONFIG_PREEMPT=y.
2) current copy implementations are measurably suboptimal and optimizing
different implementations separately is a pain and more opportunities
for bugs.
The reason for (1) is the fact that copy inside user pages are performed
with the ldm instruction which has no mean for testing user protections
and could possibly race with process preemption bypassing the COW mechanism
for example. This is a longstanding issue that we said ought to be fixed
for about two years now. The solution is to substitute those ldm insns
with a series of ldrt or strt insns to enforce user memory protection.
At least on StrongARM and XScale cores the ldm is not faster than the
equivalent ldr/str insns with a warm i-cache so there is no measurable
performance degradation with that change. The fact that the copy code is
a template makes it pretty easy to reuse the same core code as for memcpy
and benefit from the same performance optimizations.
Now (2) is best demonstrated with actual throughput measurements.
First, here is a summary of memcopy tests performed on a StrongARM core:
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 59.73 107.43
unaligned 32 61.31 74.72
aligned 100 132.47 136.15
unaligned 100 103.84 123.76
aligned 4096 130.67 130.80
unaligned 4096 130.68 130.64
aligned 1048576 68.03 68.18
unaligned 1048576 68.03 68.18
The buffer size is in bytes and the measured speed in MB/s. The copy
was performed repeatedly with given buffer and throughput averaged over
3 seconds.
Here we can see that the current kernel version has a higher entry cost
that shows up with small buffers. As buffer size grows both implementation
converge to the same throughput.
Now here's the exact same test performed on an XScale core (PXA255):
PTR alignment buffer size kernel version this version
------------------------------------------------------------
aligned 32 46.99 77.58
unaligned 32 53.61 59.59
aligned 100 107.19 136.59
unaligned 100 83.61 97.58
aligned 4096 129.13 129.98
unaligned 4096 128.36 128.53
aligned 1048576 53.76 59.41
unaligned 1048576 33.67 56.96
Again we can see the entry setup cost being higher for the current kernel
before getting to the main copy loop. Then throughput results converge
as long as the buffer remains in the cache. Then the 1MB case shows more
differences probably due to better pld placement and/or less instruction
interlocks in this proposed implementation.
Disclaimer: The PXA system was running with slower clocks than the
StrongARM system so trying to infer any conclusion by comparing those
separate sets of results side by side would be completely inappropriate.
So... What this patch does is to replace both memcpy and memmove with
an implementation based on the provided copy code template. The memmove
code is kept separate since it is used only if the memory areas involved
do overlap in which case the code is a transposition of the template but
with the copy occurring in the opposite direction (trying to fit that
mode into the template turned it into a mess not worth it for memmove
alone). And obviously both memcpy and memmove were tested with all kinds
of pointer alignments and buffer sizes to exercise all code paths for
correctness.
The next patch will provide the now trivial replacement implementation
copy_to_user and copy_from_user.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Required for future enhancement patches.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Lubbock updates:
* Provide an address for the SMC91x chip that doesn't generate
a boot-time warning (matching the EEPROM).
* Update MMC support to (a) detect card insert/remove, and
(b) report the readonly switch setting for SD cards.
Previously, MMC/SD cards had to be present at boot time else they
couldn't be detected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Update the Documentation/arm/Samsung-S3C24XX to add
example platform data initialisation, and add the
linux-arm mailing list URL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform data for the LCD/framebuffer driver for
the RX3715 LCD panel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Switch the users of ixp2000_reg_write that depend on writes being
flushed out of the write buffer by the time that function returns
over to ixp2000_reg_wrb.
When using XCB=101, writes to the same functional unit are still
guaranteed to complete in order, so we only need to protect against:
- reordering of writes to different functional units
- masking an interrupt and then reenabling the IRQ bit in CPSR
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the ixdp2x00, the slave CPU is currently not allowed to reset itself
for fear that it will do something 'funky' on the PCI bus. This fear is
ungrounded -- the slave CPU is wired up such that a CPU reset will not
cause a PCI bus reset to be done. This patch changes arch_reset() so
that the slave CPU also executes the reset sequence, allowing it to
reboot itself using /sbin/reboot.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The enp2611 version of the ixp2000 netdev driver needs to be able to
access a number of on-board peripherals. ioremap() is not suitable
for this, as that will cause XCB=000 mappings to be done, which will
make the cpu susceptible to crashing on ixp2400 erratum #66. Properly
aligned iotable mappings with MT_IXP2000_DEVICE will cause section
mappings with XCB=101 to be done, which is safe.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initialise the .owner field of the device driver
with the module that owns it, for easier tracking
of device driver ownership. (probably also better
for sysfs...)
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Initialise the .owner field of the device driver
with the module that owns it, for easier tracking
of device driver ownership.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A recent commit that removed rtas-fw.h and moved its contents to
include/asm-powerpc/rtas.h forgot to also remove the inclusion of
it in arch/powerpc/platforms/pseries/setup.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bug_entry struct had an int in the middle of pointers and unsigned
longs, and the inline asm that generated the bug table entries didn't
insert the necessary padding, so the fields following it didn't get
initialized properly and an oops resulted. This changes the int field
(the line number) to a long so that all the fields are the same size
and no padding is required.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges ppc32 and ppc64 versions of ipcbuf.h. The merge is
essentially trivial, since the structure defined in each version was
already identical. Only wrinkle is that the merged version now
includes linux/types.h in order to get the fixed width integer types.
In fact, the old versions probably should have been including that
anyway, since the file uses various __kernel_*_t types.
Built and booted on G5, built for 32-bit pmac, but not booted, since
the merge tree currently doesn't boot there.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch simply moves files over to arch/powerpc without making
any changes to them.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The nvram code formally known as bpa_nvram.c is rather
generic really, so it is quite likely to be useful to
future boards not based on cell.
This patch puts it into arch/powerpc/sysdev.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cell uses the same code as pSeries for flashing the firmware
through rtas, so the implementation should not be part of
platforms/pseries.
Put it into arch/powerpc/kernel instead.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the conversion to the merge tree, the Cell specific
SMP initialization was removed from the pSeries code.
This creates a new Cell specific SMP implementation file.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The official name for BPA is now CBEA (Cell Broadband
Engine Architecture). This patch renames all occurences
of the term BPA to 'Cell' for easier recognition.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
Right now we do it at queueing time, which works alright for reads
(since they are usually sync), but not for async writes since we can
queue io a lot faster than we can complete it. This makes the vmstat
output look extremely bursty.
Signed-off-by: Jens Axboe <axboe@suse.de>
The USB "handoff" code is an early PCI quirk to make sure we own the USB
controller (as opposed to the BIOS/SMM). But if the controller isn't
even enabled yet, don't try to access it.
Acked-by: Paul Mackerras <paulus@samba.org> (who had an alternate patch)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
By parsing the command line earlier, we can add the mem= value to the
flattened device tree and let the generic code sort out the memory limit
for us.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Change USER/KERNEL_DS so that the merged version of
__strnlen_user can be used which allows us to complete the
removal of arch/ppc64/lib/.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Commit f2b36db692 causes a bootup hang on
at least one machine. Revert for now until we understand why. The old
code may be ugly, but it works.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If I/O is active on the adapter, and an unexpected interrupt is pending
during initialization, the driver blows it's brains out. Since the driver
didn't initiate the I/O, the data in it's internal tables will contain NULL
pointers.
When this condition is detected, a "flush cache and reset" is performed.
The flush cache allows any pending "lazy writes" that the adapter is
processing to complete ( a "must have" for a RAID adapter ) and the reset
puts the adapter back into a known, good state.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here is a complimentary insurance policy for those feeling a bit insecure.
You don't have to accept this. However, if you do, you can't blame me for
it :)
> 1) dccp_transmit_skb sets the owner for all packets except data packets.
We can actually verify this by looking at pkt_type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds the magic IO wakeup code for the CardBus version of the
Creative Labs Audigy 2 to the snd-emu10k1 driver.
Without the magic IO enable sequence, reading from the IO region of the
card will fail spectacularly, and the machine will hang.
My next task will be getting the driver to actually play sound without
distortion.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
[ This is a work-in-progress, but since it avoids a total lockup
if the emu10k module is loaded on a machine with the cardbus
card inserted, we're better off with it than without it, even
if sound quality is bad right now ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
jfs has never been setting i_ctime or i_mtime when creating either hard
or symbolic links. I'm surprised nobody had noticed until now.
Thanks to Chris Spiegel for reporting the problem.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Corrects the very inefficent method of finding free context_ids in
get_mmu_context(). Instead of walking the task_list of all processes,
2 bitmaps are used to efficently store and lookup state, inuse and
needs flushing. The entire rid address space is now used before calling
wrap_mmu_context and global tlb flushing.
Special thanks to Ken and Rohit for their review and modifications in
using a bit flushmap.
Signed-off-by: Peter Keilty <peter.keilty@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the inode count is zero in inode writeback, the
WARN_ON(!(inode->i_state & I_WILL_FREE));
is broken, and needs to test for either I_WILL_FREE|I_FREEING.
When the inode is in I_FREEING state, it's already out of the visibility
of the vm so it can't be freed so it doesn't require the __iget and the
generic_delete_inode path can call the sync internally to the lowlevel
fs callback during the last iput. So the inode being in I_FREEING is
also a valid condition for calling the sync with i_count == 0.
The specific stack trace is this:
0xc00000007b8fb6e0 0xc00000000010118c .__writeback_single_inode +0x5c
0xc00000007b8fb6e0 0xc0000000001014dc (lr) .sync_inode +0x3c
0xc00000007b8fb790 0xc0000000001014dc .sync_inode +0x3c
0xc00000007b8fb820 0xc0000000001a5020 .ext2_sync_inode +0x64
0xc00000007b8fb8f0 0xc0000000001a65b4 .ext2_truncate +0x3f8
0xc00000007b8fba40 0xc0000000001a6940 .ext2_delete_inode +0xdc
0xc00000007b8fbac0 0xc0000000000f7a5c .generic_delete_inode +0x124
0xc00000007b8fbb50 0xc0000000000f5fe0 .iput +0xb8
0xc00000007b8fbbe0 0xc0000000000e9fd4 .sys_unlink +0x2a8
0xc00000007b8fbd10 0xc00000000001048c .ret_from_syscall_1 +0x0
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Garzik <jgarzik@pobox.com> points out that this was wrong: we need to
disable local interrupts while holding KM_IRQ0 due to IRQ sharing.
And holding interrupts off during a big PIO opration is expensive, so we only
want to do that if we know the page was highmem.
So revert commit 17fd47ab4d
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While we're at it let's reorganise the set_owner_w calls a little so that:
1) dccp_transmit_skb sets the owner for all packets except data packets.
2) Add dccp_skb_entail to set owner for packets queued for retransmission.
3) Make dccp_transmit_skb static.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
My only objection to pfn_to_kaddr, which was introduced for HotPlug memory,
is that all arches have an identical implementation. I haven't had a chance
to pursue why yet. There is probably some arch issue I'm unaware of.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I find that linux will reply echo request destined to an address which
belongs to an interface other than the one from which the request received.
This behavior doesn't make sense for link local address.
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> said:
Please note that sender does need to setup neighbor entry by hand to reproduce
this bug. (Link-local address on eth1 is not visible on eth0, from the point
of view of neighbor discovery in IPv6.)
+--------+ +--------+
| sender | | router |
+---+----+ +-+----+-+
|eth0 eth0| |eth1
-----+----------------------+- -+--------------
Signed-off-by: Yan Zheng <yanzheng@21cn.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Like ip_tables already has it for some time, this adds support for
having multiple revisions for each match/target. We steal one byte from
the name in order to accomodate a 8 bit version number.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Use compare_ether_addr in bridge code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tejun Heo notes:
"I'm currently debugging this. The problem is that we are using the
generic dispatch queue directly in the noop sched and merging is NOT
allowed on dispatch queues but generic handling of last_merge tries
to merge requests. I'm still trying to verify this, so I'll be back
with results soon."
In the meantime, disable merging for noop by setting REQ_NOMERGE in
elevator_noop_add_request().
Eventually, we should add a noop_list and do the dispatching like in the
other io schedulers. Merging is still beneficial for noop (and it has
always done it).
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't clear ->elevator_data on exit, if we are switching queues we are
overwriting the data of the new io scheduler.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor cleanups: fix a misleading comment, and get rid of attr_mask
variables that are only used to hold constants (just use the constants
directly).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix wqe_to_link() to use a structure field that we know is definitely
always unused for receive work requests, so that it really avoids the
free list corruption bug that the comment claims it does.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace CQs that have no completion event channel attached end up
with their cq_context set to NULL. However, asynchronous events like
"CQ overrun" can still occur on such CQs, so add a uverbs_file member
to struct ib_ucq_object that we can follow to deliver these events.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Folk seem to get confused when they see two or more ttyS0 ports
appearing at boot time. One comes from the legacy table, and
one from PNP.
Hence, display the bus ID of the device which supplied the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The problem is that adbhid[]->input is NULL, so the kernel oopses with
a null pointer dereference as soon as a key is pressed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
Integrate ata_exec() and ata_tf_to_host() into their only caller,
ata_bus_edd().
Rename ata_tf_to_host_nolock() to ata_tf_to_host().
This makes locking a bit easier to review, and may help pave the way for
future changes.
We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line. This puts the declaration
in system.h and the definition in mem.c. This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes duplicate directory scanning code from fs/fat/dir.c. The
two functions that share identical code are fat_readdirx() and
fat_search_long(). This patch also renames fat_readdirx to __fat_readdir().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now, vfat_rename() is using vfat_find() for sanity check. This removes that
sanity check, the cost of sanity check is too high.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Combine a bit of redundant code between force_sig_info() and
force_sig_specific().
Signed-off-by: paulmck@us.ibm.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes checks for ->si_code == SI_TIMER from send_signal,
specific_send_sig_info, __group_send_sig_info.
I think posix-timers.c used these functions some time ago, now it sends
signals via send_{,group_}sigqueue, so these hooks are unneeded.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch simplifies some checks for magic siginfo values. It should not
change the behaviour in any way.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch replaces hardcoded SEND_SIG_xxx constants with
their symbolic names.
No changes in affected .o files.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use kzalloc() instead of kmalloc + memset.
- Clean/fix some printk's.
- Use NULL for pointers instead of 0.
- Combine hpet busy searching locations into a function call.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Use HPET physical address to detect duplicates, not logical addresses.
Using logical (mapped) addresses fails to detect duplicates
because ioremap() returns a new mapped address each time.
- iounmap() regions when duplicate/busy areas are found.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the ACPI HPET description table to use a resource type of FIXED_MEM32
for the HPET reource. Use the fixed resoure size of 1 KB for the HPET
resource as per the HPET spec.
Signed-off-by: Randy Dunlap <randy_d_dunlap@linux.intel.com>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When booting, display the timer frequency in Hertz instead of as tick length
in nanoseconds. Apart from saving a local variable, this makes the message
more easily comprehensible.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the hpet_ioctl_common() function, devp->hd_hpets is already cached in the
hpetp variable, so we can use just that.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix two instances where a function would access the first HPET device instead
of the current one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clear the ht_opaque field in the hpet_register() function before searching for
a free timer to prevent the function from incorrectly assuming that the search
succeeded afterwards.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a division by zero that happened when the HPET_INFO ioctl was called
before a timer frequency had been set.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a wrong memory access in hpet_ioctl_common(). It was not possible to use
the HPET_INFO ioctl from kernel space because it always called copy_to_user().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reads from an HPET register require a round trip to the south bridge and are
almost as slow as PCI reads. By caching the last value we've written to the
comparator register, we can eliminate all HPET reads from the fast path in the
emulated RTC interrupt handler.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that the RTC timer is in non-periodic mode; some stupid BIOS might
have initialized it to periodic mode.
Furthermore, don't set the SETVAL bit in the config register. This wouldn't
have any effect unless the timer was in period mode (which it isn't), and then
the actual timer frequency would be half that of the desired one because
incrementing the comparator in the interrupt handler would be done after the
hardware has already incremented it itself.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the emulated RTC interrupt is no longer needed, we better disable it;
otherwise, we get a spurious interrupt whenever the timer has rolled over and
reaches the same comparator value.
Having a superfluous interrupt every five minutes doesn't hurt much, but it's
bad style anyway. ;-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for shared HPET interrupts.
The driver previously acknowledged interrupts for both edge and level
interrupts, but didn't actually allow a shared interrupt in the latter case.
We use a new per-timer flag to save whether the timer's interrupt might be
shared, and use it to do the processing required for level interrupts only if
necessary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was only the RTC hardware that restricted interrupt frequencies to a power
of two. There is no reason to take over this restriction into the HPET
driver, so remove the offending check.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes several reads of a timer's config register that serve no
purpose whatsoever.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 32-bit architectures, the multiplication in the argument for
hpet_time_div() often overflows. In the typical case of a 14.32 MHz timer,
this happens when the desired frequency exceeds 61 Hz.
To avoid this multiplication, we can precompute and store the hardware
timer frequency, instead of the period, in the device structure, which
leaves us with a simple division when computing the number of timer ticks.
As a side effect, this also removes a theoretical bug where the timer
interpolator's frequency would be computed as a 32-bit value even if the
HPET frequency is greater than 2^32 Hz (the HPET spec allows up to 10 GHz).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disallow setting an interrupt frequency of zero (which would result in a
division by zero), and disallow enabling the interrupt when the frequency
hasn't yet been set (which would use an interrupt period of zero).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the Infineon TPM driver off pci device and makes it a pure pnp-driver.
It includes pnp-port validation and region requesting.
Signed-off-by: Marcel Selhorst <selhorst@crypto.rub.de>
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the nsc driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the atmel driver from a pci driver to a platform driver.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in support of moving away from the lpc bus pci_dev. The power
management prototypes used by platform drivers is different but the
functionality remains the same.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the tpm does not have it's own pci id we have been consuming the lpc
bus. This is not correct and causes problems to support non lpc bus chips.
This patch removes the dependency on pci_dev from tpm.c The subsequent patches
will stop the supported chips from registering as pci drivers.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is in preparation of supporting chips that are not necessarily on
the lpc bus and thus are not accessed with inb's and outb's. The patch
replaces the call to get the chip's status in the tpm.c file with a vendor
specific status function. The patch also defines the function for each of the
current supported devices.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's nasty to set random drivers to default m because people who just press
enter on make oldconfig get these. Remove the default m
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simplify the UP (1 CPU) implementatin of set_cpus_allowed.
The one CPU is hardcoded to be cpu 0 - so just test for that bit, and avoid
having to pick up the cpu_online_map.
Also, unexport cpu_online_map: it was only needed for set_cpus_allowed().
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I made a patch that detects if libintl.h (needed for nls) is present on the
host system and if it's not, it nls support is disabled by providing
dummies for the used nls functions.
This way if there is nls support on the host system the *config targets
will build according to Arnaldo Carvalho de Melo's i18n modifications, else
it just uses the original English messages.
I have also made a bug report at kernel's bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=5501
And there is a discussion about this problem in Gentoo's bugzilla:
http://bugs.gentoo.org/show_bug.cgi?id=99810
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of (char *) casts removed in a previous cleanup patch in
lib/string.c:memmove() were actually useful, as they suppressed a couple of
warnings:
assignment discards qualifiers from pointer target type
Fix by declaring the local variable const in the first place, so casts
aren't needed to strip the const qualifier.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a filesystem passes an idiotic blocksize into bread(), __getblk_slow() will
warn and will return NULL. We have a report (from Hubert Tonneau
<hubert.tonneau@fullpliant.org>) of isofs_fill_super() doing this (passing in
a silly block size) against an unplugged CDROM drive.
But a couple of __getblk_slow() callers forgot to check for the NULL bh, hence
oops.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__MUTEX_INITIALIZER() has no users, and equates to the more commonly used
DECLARE_MUTEX(), thus making it pretty much redundant. Remove it for good.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver had incorrectly wrapped module_init(rp_init) in #ifdef MODULE,
so it worked only when compiled as a module.
Tested by Wolfgang Denk with this device:
00:0e.0 Communication controller: Comtrol Corporation RocketPort 8 port w/RJ11 connectors (rev 04)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 7000 [size=64]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change corrects an omission in posix_cpu_timer_schedule, so that it
correctly propagates the overrun calculation to where it will get reported
to the user.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is a rewrite of the one submitted on October 1st, using modules
(http://marc.theaimsgroup.com/?l=linux-kernel&m=112819093522998&w=2).
This rewrite adds a tristate CONFIG_RCU_TORTURE_TEST, which enables an
intense torture test of the RCU infratructure. This is needed due to the
continued changes to the RCU infrastructure to accommodate dynamic ticks,
CPU hotplug, realtime, and so on. Most of the code is in a separate file
that is compiled only if the CONFIG variable is set. Documentation on how
to run the test and interpret the output is also included.
This code has been tested on i386 and ppc64, and an earlier version of the
code has received extensive testing on a number of architectures as part of
the PREEMPT_RT patchset.
Signed-off-by: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a long-standing vgacon bug: characters with the bright bit
set were left on the screen and not blacked out. All I did was that I
lookuped up some examples on the net about setting the vga palette, and
added the call missing from the linux kernel, but included in all other
ones. It works for me.
You can test this by writing something with the bright set to the
console, for example:
echo -e "\e[1;31mhello there\e[0m"
and then wait for the console to blank itself (by default, after 10 mins
of inactivity), maybe making it faster using
setterm -blank 1
so you only have to wait 1 minute.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds tests for the return value of sb_getblk() in the ext2/3
filesystems. In fs/buffer.c it is stated that the getblk() function never
fails. However, it does can return NULL in some situations due to I/O
errors, which may lead us to NULL pointer dereferences
Signed-off-by: Glauber de Oliveira Costa <glommer@br.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
list_move(&inode->i_list, &inode_in_use);
} else {
list_move(&inode->i_list, &inode_unused);
+ inodes_stat.nr_unused++;
}
}
wake_up_inode(inode);
Are you sure the above diff is correct? It was added somewhere between
2.6.5 and 2.6.8. I think it's wrong.
The only way I can imagine the i_count to be zero in the above path, is
that I_WILL_FREE is set. And if I_WILL_FREE is set, then we must not
increase nr_unused. So I believe the above change is buggy and it will
definitely overstate the number of unused inodes and it should be backed
out.
Note that __writeback_single_inode before calling __sync_single_inode, can
drop the spinlock and we can have both the dirty and locked bitflags clear
here:
spin_unlock(&inode_lock);
__wait_on_inode(inode);
iput(inode);
XXXXXXX
spin_lock(&inode_lock);
}
use inode again here
a construct like the above makes zero sense from a reference counting
standpoint.
Either we don't ever use the inode again after the iput, or the
inode_lock should be taken _before_ executing the iput (i.e. a __iput
would be required). Taking the inode_lock after iput means the iget was
useless if we keep using the inode after the iput.
So the only chance the 2.6 was safe to call __writeback_single_inode
with the i_count == 0, is that I_WILL_FREE is set (I_WILL_FREE will
prevent the VM to free the inode in XXXXX).
Potentially calling the above iput with I_WILL_FREE was also wrong
because it would recurse in iput_final (the second mainline bug).
The below (untested) patch fixes the nr_unused accounting, avoids recursing
in iput when I_WILL_FREE is set and makes sure (with the BUG_ON) that we
don't corrupt memory and that all holders that don't set I_WILL_FREE, keeps
a reference on the inode!
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparse complains about every MODULE_PARM used in a module: warning: symbol
'__parm_foo' was not declared. Should it be static?
The fix is to split declaration and initialization. While MODULE_PARM is
obsolete, it's not something sparse should report.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They aren't used anywhere in that file.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because people can play games reprogramming keys and leaving traps for the
next user of the console.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert existing function docs to kernel-doc format. Eliminate all
kernel-doc warnings. Fix some doc typos and a little whitespace cleanup.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix warnings from sparse due to un-declared functions that should either
have a header file or have been declared static
fs/ext2/bitmap.c:14:15: warning: symbol 'ext2_count_free' was not declared. Should it be static?
fs/ext2/namei.c:92:15: warning: symbol 'ext2_get_parent' was not declared. Should it be static?
fs/ext3/bitmap.c:15:15: warning: symbol 'ext3_count_free' was not declared. Should it be static?
fs/ext3/namei.c:1013:15: warning: symbol 'ext3_get_parent' was not declared. Should it be static?
fs/ext3/xattr.c:214:1: warning: symbol 'ext3_xattr_block_get' was not declared. Should it be static?
fs/ext3/xattr.c:358:1: warning: symbol 'ext3_xattr_block_list' was not declared. Should it be static?
fs/ext3/xattr.c:630:1: warning: symbol 'ext3_xattr_block_find' was not declared. Should it be static?
fs/ext3/xattr.c:863:1: warning: symbol 'ext3_xattr_ibody_find' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
de_thread() sends SIGKILL to all sub-threads and waits them to die in 'D'
state. It is possible that one of the threads already dequeued coredump
signal. When de_thread() unlocks ->sighand->lock that thread can enter
do_coredump()->coredump_wait() and cause a deadlock.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added a Receive_Abort to the Marvell serial driver
Fix occasional input overrun errors on Marvell serial driver
- If the Marvell serial driver is repeatedly started and then stopped it
will occasionally report an input overrun error when started.
- Added a Receive_Abort to the Marvell serial driver to abort previously
received receive errors when re-starting the receive
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Carlos Sanchez <csanchez@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Setting ctime is implicit in all setattr cases, so the FATTR_CTIME
definition is unnecessary.
It is used by neither the kernel nor by userspace.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct some typos and inconsistent use of "initialise" vs "initialize" in
comments. Reported by Ioannis Barkas.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Back about a year ago when I last fiddled heavily with the do_wait code, I
was thinking too hard about the wrong thing and I now think I introduced a
bug whose inverse thought I was fixing.
Apparently noone was looking too hard over much shoulder, so as to cite my
bogus reasoning at the time. In the race condition when PTRACE_ATTACH is
about to steal a child and then the child hits a tracing event (what
my_ptrace_child checks for), the real parent does need to set its flag
noting it has some eligible live children. Otherwise a spurious ECHILD
error is possible, since the child in question is not yet on the
ptrace_children list.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various small mods for the Altix ioc4 serial driver - mostly cleanup:
- remove UIF_INITIALIZED usage
- use the 'lock' from uart_port
- better multiple card support
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed some problems while running ext3 with the debug flag set on.
More precisely, I was unable to umount the filesystem. Some investigation
took me to the patch that follows.
At a first glance , the lock/unlock I've taken out seems really not
necessary, as the main code (outside debug) does not lock the super. The
only additional danger operations that debug code introduces seems to be
related to bitmap, but bitmap operations tends to be all atomic anyway.
I also took the opportunity to fix 2 spelling errors.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch deletes pointless code from coredump_wait().
1. It does useless mm->core_waiters inc/dec under mm->mmap_sem,
but any changes to ->core_waiters have no effect until we drop
->mmap_sem.
2. It calls yield() for absolutely unknown reason.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PF_DEAD setting doesn't belong to exit_notify(), move it to a proper
place.
Signed-off-by: Coywolf Qi Hunt <qiyong@fc-cn.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Removes some trailing whitespace
- Breaks long lines and make other small changes to conform to CodingStyle
- Add explicit printk loglevels in two places.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some unneeded casts.
Avoid an assignment in the case of kmalloc failure.
Break a few instances of if (foo) whatever; into two lines.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch gets rid of a "statement without effect" warning when
CONFIG_KEYS is disabled by making use of the return value of key_get().
The compiler will optimise all of this away when keys are disabled.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds LSM hooks for key management facilities. The notable
changes are:
(1) The key struct now supports a security pointer for the use of security
modules. This will permit key labelling and restrictions on which
programs may access a key.
(2) Security modules get a chance to note (or abort) the allocation of a key.
(3) The key permission checking can now be enhanced by the security modules;
the permissions check consults LSM if all other checks bear out.
(4) The key permissions checking functions now return an error code rather
than a boolean value.
(5) An extra permission has been added to govern the modification of
attributes (UID, GID, permissions).
Note that there isn't an LSM hook specifically for each keyctl() operation,
but rather the permissions hook allows control of individual operations based
on the permission request bits.
Key management access control through LSM is enabled by automatically if both
CONFIG_KEYS and CONFIG_SECURITY are enabled.
This should be applied on top of the patch ensubjected:
[PATCH] Keys: Possessor permissions should be additive
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export user-defined key operations so that those who wish to define their
own key type based on the user-defined key operations may do so (as has
been requested).
The header file created has been placed into include/keys/user-type.h, thus
creating a directory where other key types may also be placed. Any
objections to doing this?
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-Off-By: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes page_pte_prot and page_pte macros from all
architectures. Some architectures define both, some only page_pte (broken)
and others none. These macros are not used anywhere.
page_pte_prot(page, prot) is identical to mk_pte(page, prot) and
page_pte(page) is identical to page_pte_prot(page, __pgprot(0)).
* The following architectures define both page_pte_prot and page_pte
arm, arm26, ia64, sh64, sparc, sparc64
* The following architectures define only page_pte (broken)
frv, i386, m32r, mips, sh, x86-64
* All other architectures define neither
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes redundant assignment from __pagevec_release_nonlru().
pages_to_free.cold is set to pvec->cold by pagevec_init() call right above
the assignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When __generic_file_aio_read() hits an error during reading, it reports the
error iff nothing has successfully been read yet. This is condition - when
an error occurs, if nothing has been read/written, report the error code;
otherwise, report the amount of bytes successfully transferred upto that
point.
This corner case can be exposed by performing readv(2) with the following
iov.
iov[0] = len0 @ ptr0
iov[1] = len1 @ NULL (or any other invalid pointer)
iov[2] = len2 @ ptr2
When file size is enough, performing above readv(2) results in
len0 bytes from file_pos @ ptr0
len2 bytes from file_pos + len0 @ ptr2
And the return value is len0 + len2. Test program is attached to this
mail.
This patch makes __generic_file_aio_read()'s error handling identical to
other functions.
#include <stdio.h>
#include <stdlib.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
#include <sys/uio.h>
#include <errno.h>
#include <string.h>
int main(int argc, char **argv)
{
const char *path;
struct stat stbuf;
size_t len0, len1;
void *buf0, *buf1;
struct iovec iov[3];
int fd, i;
ssize_t ret;
if (argc < 2) {
fprintf(stderr, "Usage: testreadv path (better be a "
"small text file)\n");
return 1;
}
path = argv[1];
if (stat(path, &stbuf) < 0) {
perror("stat");
return 1;
}
len0 = stbuf.st_size / 2;
len1 = stbuf.st_size - len0;
if (!len0 || !len1) {
fprintf(stderr, "Dude, file is too small\n");
return 1;
}
if ((fd = open(path, O_RDONLY)) < 0) {
perror("open");
return 1;
}
if (!(buf0 = malloc(len0)) || !(buf1 = malloc(len1))) {
perror("malloc");
return 1;
}
memset(buf0, 0, len0);
memset(buf1, 0, len1);
iov[0].iov_base = buf0;
iov[0].iov_len = len0;
iov[1].iov_base = NULL;
iov[1].iov_len = len1;
iov[2].iov_base = buf1;
iov[2].iov_len = len1;
printf("vector ");
for (i = 0; i < 3; i++)
printf("%p:%zu ", iov[i].iov_base, iov[i].iov_len);
printf("\n");
ret = readv(fd, iov, 3);
if (ret < 0)
perror("readv");
printf("readv returned %zd\nbuf0 = [%s]\nbuf1 = [%s]\n",
ret, (char *)buf0, (char *)buf1);
return 0;
}
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I could seldom reproduce a deadlock with a task not killable in T state
(TASK_STOPPED, not TASK_TRACED) by attaching a NPTL threaded program to
gdb, by segfaulting the task and triggering a core dump while some other
task is executing exit_group and while one task is in ptrace_attached
TASK_STOPPED state (not TASK_TRACED yet). This originated from a gdb
bugreport (the fact gdb was segfaulting the task wasn't a kernel bug), but
I just incidentally noticed the gdb bug triggered a real kernel bug as
well.
Most threads hangs in exit_mm because the core_dumping is still going, the
core dumping hangs because the stopped task doesn't exit, the stopped task
can't wakeup because it has SIGNAL_GROUP_EXIT set, hence the deadlock.
To me it seems that the problem is that the force_sig_specific(SIGKILL) in
zap_threads is a noop if the task has PF_PTRACED set (like in this case
because gdb is attached). The __ptrace_unlink does nothing because the
signal->flags is set to SIGNAL_GROUP_EXIT|SIGNAL_STOP_DEQUEUED (verified).
The above info also shows that the stopped task hit a race and got the stop
signal (presumably by the ptrace_attach, only the attach, state is still
TASK_STOPPED and gdb hangs waiting the core before it can set it to
TASK_TRACED) after one of the thread invoked the core dump (it's the core
dump that sets signal->flags to SIGNAL_GROUP_EXIT).
So beside the fact nobody would wakeup the task in __ptrace_unlink (the
state is _not_ TASK_TRACED), there's a secondary problem in the signal
handling code, where a task should ignore the ptrace-sigstops as long as
SIGNAL_GROUP_EXIT is set (or the wakeup in __ptrace_unlink path wouldn't be
enough).
So I attempted to make this patch that seems to fix the problem. There
were various ways to fix it, perhaps you prefer a different one, I just
opted to the one that looked safer to me.
I also removed the clearing of the stopped bits from the zap_other_threads
(zap_other_threads was safe unlike zap_threads). I don't like useless
code, this whole NPTL signal/ptrace thing is already unreadable enough and
full of corner cases without confusing useless code into it to make it even
less readable. And if this code is really needed, then you may want to
explain why it's not being done in the other paths that sets
SIGNAL_GROUP_EXIT at least.
Even after this patch I still wonder who serializes the read of
p->ptrace in zap_threads.
Patch is called ptrace-core_dump-exit_group-deadlock-1.
This was the trace I've got:
test T ffff81003e8118c0 0 14305 1 14311 14309 (NOTLB)
ffff810058ccdde8 0000000000000082 000001f4000037e1 ffff810000000013
00000000000000f8 ffff81003e811b00 ffff81003e8118c0 ffff810011362100
0000000000000012 ffff810017ca4180
Call Trace:<ffffffff801317ed>{try_to_wake_up+893} <ffffffff80141677>{finish_stop+87}
<ffffffff8014367f>{get_signal_to_deliver+1359} <ffffffff8010d3ad>{do_signal+157}
<ffffffff8013deee>{ptrace_check_attach+222} <ffffffff80111575>{sys_ptrace+2293}
<ffffffff80131810>{default_wake_function+0} <ffffffff80196399>{sys_ioctl+73}
<ffffffff8010dd27>{sysret_signal+28} <ffffffff8010e00f>{ptregscall_common+103}
test D ffff810011362100 0 14309 1 14305 14312 (NOTLB)
ffff810053c81cf8 0000000000000082 0000000000000286 0000000000000001
0000000000000195 ffff810011362340 ffff810011362100 ffff81002e338040
ffff810001e0ca80 0000000000000001
Call Trace:<ffffffff801317ed>{try_to_wake_up+893} <ffffffff8044677d>{wait_for_completion+173}
<ffffffff80131810>{default_wake_function+0} <ffffffff80137435>{exit_mm+149}
<ffffffff801381af>{do_exit+479} <ffffffff80138d0c>{do_group_exit+252}
<ffffffff801436db>{get_signal_to_deliver+1451} <ffffffff8010d3ad>{do_signal+157}
<ffffffff8013deee>{ptrace_check_attach+222} <ffffffff80140850>{specific_send_sig_info+2
<ffffffff8014208a>{force_sig_info+186} <ffffffff804479a0>{do_int3+112}
<ffffffff8010e308>{retint_signal+61}
test D ffff81002e338040 0 14311 1 14716 14305 (NOTLB)
ffff81005ca8dcf8 0000000000000082 0000000000000286 0000000000000001
0000000000000120 ffff81002e338280 ffff81002e338040 ffff8100481cb740
ffff810001e0ca80 0000000000000001
Call Trace:<ffffffff801317ed>{try_to_wake_up+893} <ffffffff8044677d>{wait_for_completion+173}
<ffffffff80131810>{default_wake_function+0} <ffffffff80137435>{exit_mm+149}
<ffffffff801381af>{do_exit+479} <ffffffff80142d0e>{__dequeue_signal+558}
<ffffffff80138d0c>{do_group_exit+252} <ffffffff801436db>{get_signal_to_deliver+1451}
<ffffffff8010d3ad>{do_signal+157} <ffffffff8013deee>{ptrace_check_attach+222}
<ffffffff80140850>{specific_send_sig_info+208} <ffffffff8014208a>{force_sig_info+186}
<ffffffff804479a0>{do_int3+112} <ffffffff8010e308>{retint_signal+61}
test D ffff810017ca4180 0 14312 1 14309 13882 (NOTLB)
ffff81005d15fcb8 0000000000000082 ffff81005d15fc58 ffffffff80130816
0000000000000897 ffff810017ca43c0 ffff810017ca4180 ffff81003e8118c0
0000000000000082 ffffffff801317ed
Call Trace:<ffffffff80130816>{activate_task+150} <ffffffff801317ed>{try_to_wake_up+893}
<ffffffff8044677d>{wait_for_completion+173} <ffffffff80131810>{default_wake_function+0}
<ffffffff8018cdc3>{do_coredump+819} <ffffffff80445f52>{thread_return+82}
<ffffffff801436d4>{get_signal_to_deliver+1444} <ffffffff8010d3ad>{do_signal+157}
<ffffffff8013deee>{ptrace_check_attach+222} <ffffffff80140850>{specific_send_sig_info+2
<ffffffff804472e5>{_spin_unlock_irqrestore+5} <ffffffff8014208a>{force_sig_info+186}
<ffffffff804476ff>{do_general_protection+159} <ffffffff8010e308>{retint_signal+61}
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch automatically updates a tasks NUMA mempolicy when its cpuset
memory placement changes. It does so within the context of the task,
without any need to support low level external mempolicy manipulation.
If a system is not using cpusets, or if running on a system with just the
root (all-encompassing) cpuset, then this remap is a no-op. Only when a
task is moved between cpusets, or a cpusets memory placement is changed
does the following apply. Otherwise, the main routine below,
rebind_policy() is not even called.
When mixing cpusets, scheduler affinity, and NUMA mempolicies, the
essential role of cpusets is to place jobs (several related tasks) on a set
of CPUs and Memory Nodes, the essential role of sched_setaffinity is to
manage a jobs processor placement within its allowed cpuset, and the
essential role of NUMA mempolicy (mbind, set_mempolicy) is to manage a jobs
memory placement within its allowed cpuset.
However, CPU affinity and NUMA memory placement are managed within the
kernel using absolute system wide numbering, not cpuset relative numbering.
This is ok until a job is migrated to a different cpuset, or what's the
same, a jobs cpuset is moved to different CPUs and Memory Nodes.
Then the CPU affinity and NUMA memory placement of the tasks in the job
need to be updated, to preserve their cpuset-relative position. This can
be done for CPU affinity using sched_setaffinity() from user code, as one
task can modify anothers CPU affinity. This cannot be done from an
external task for NUMA memory placement, as that can only be modified in
the context of the task using it.
However, it easy enough to remap a tasks NUMA mempolicy automatically when
a task is migrated, using the existing cpuset mechanism to trigger a
refresh of a tasks memory placement after its cpuset has changed. All that
is needed is the old and new nodemask, and notice to the task that it needs
to rebind its mempolicy. The tasks mems_allowed has the old mask, the
tasks cpuset has the new mask, and the existing
cpuset_update_current_mems_allowed() mechanism provides the notice. The
bitmap/cpumask/nodemask remap operators provide the cpuset relative
calculations.
This patch leaves open a couple of issues:
1) Updating vma and shmfs/tmpfs/hugetlbfs memory policies:
These mempolicies may reference nodes outside of those allowed to
the current task by its cpuset. Tasks are migrated as part of jobs,
which reside on what might be several cpusets in a subtree. When such
a job is migrated, all NUMA memory policy references to nodes within
that cpuset subtree should be translated, and references to any nodes
outside that subtree should be left untouched. A future patch will
provide the cpuset mechanism needed to mark such subtrees. With that
patch, we will be able to correctly migrate these other memory policies
across a job migration.
2) Updating cpuset, affinity and memory policies in user space:
This is harder. Any placement state stored in user space using
system-wide numbering will be invalidated across a migration. More
work will be required to provide user code with a migration-safe means
to manage its cpuset relative placement, while preserving the current
API's that pass system wide numbers, not cpuset relative numbers across
the kernel-user boundary.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the forthcoming task migration support, a key calculation will be
mapping cpu and node numbers from the old set to the new set while
preserving cpuset-relative offset.
For example, if a task and its pages on nodes 8-11 are being migrated to
nodes 24-27, then pages on node 9 (the 2nd node in the old set) should be
moved to node 25 (the 2nd node in the new set.)
As with other bitmap operations, the proper way to code this is to provide
the underlying calculation in lib/bitmap.c, and then to provide the usual
cpumask and nodemask wrappers.
This patch provides that. These operations are termed 'remap' operations.
Both remapping a single bit and a set of bits is supported.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch keeps pdflush daemons on the same cpuset as their parent, the
kthread daemon.
Some large NUMA configurations put as much as they can of kernel threads
and other classic Unix load in what's called a bootcpuset, keeping the rest
of the system free for dedicated jobs.
This effort is thwarted by pdflush, which dynamically destroys and
recreates pdflush daemons depending on load.
It's easy enough to force the originally created pdflush deamons into the
bootcpuset, at system boottime. But the pdflush threads created later were
allowed to run freely across the system, due to the necessary line in their
startup kthread():
set_cpus_allowed(current, CPU_MASK_ALL);
By simply coding pdflush to start its threads with the cpus_allowed
restrictions of its cpuset (inherited from kthread, its parent) we can
ensure that dynamically created pdflush threads are also kept in the
bootcpuset.
On systems w/o cpusets, or w/o a bootcpuset implementation, the following
will have no affect, leaving pdflush to run on any CPU, as before.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for renaming cpusets. Only allow simple rename of cpuset
directories in place. Don't allow moving cpusets elsewhere in hierarchy or
renaming the special cpuset files in each cpuset directory.
The usefulness of this simple rename became apparent when developing task
migration facilities. It allows building a second cpuset hierarchy using
new names and containing new CPUs and Memory Nodes, moving tasks from the
old to the new cpusets, removing the old cpusets, and then renaming the new
cpusets to be just like the old names, so that any knowledge that the tasks
had of their cpuset names will still be valid.
Leaf node cpusets can be migrated to other CPUs or Memory Nodes by just
updating their 'cpus' and 'mems' files, but because no cpuset can contain
CPUs or Nodes not in its parent cpuset, one cannot do this in a cpuset
hierarchy without first expanding all the non-leaf cpusets to contain the
union of both the old and new CPUs and Nodes, which would obfuscate the
one-to-one migration of a task from one cpuset to another required to
correctly migrate the physical page frames currently allocated to that
task.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Overhaul cpuset locking. Replace single semaphore with two semaphores.
The suggestion to use two locks was made by Roman Zippel.
Both locks are global. Code that wants to modify cpusets must first
acquire the exclusive manage_sem, which allows them read-only access to
cpusets, and holds off other would-be modifiers. Before making actual
changes, the second semaphore, callback_sem must be acquired as well. Code
that needs only to query cpusets must acquire callback_sem, which is also a
global exclusive lock.
The earlier problems with double tripping are avoided, because it is
allowed for holders of manage_sem to nest the second callback_sem lock, and
only callback_sem is needed by code called from within __alloc_pages(),
where the double tripping had been possible.
This is not quite the same as a normal read/write semaphore, because
obtaining read-only access with intent to change must hold off other such
attempts, while allowing read-only access w/o such intention. Changing
cpusets involves several related checks and changes, which must be done
while allowing read-only queries (to avoid the double trip), but while
ensuring nothing changes (holding off other would be modifiers.)
This overhaul of cpuset locking also makes careful use of task_lock() to
guard access to the task->cpuset pointer, closing a couple of race
conditions noticed while reading this code (thanks, Roman). I've never
seen these races fail in any use or test.
See further the comments in the code.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove a rather hackish depth counter on cpuset locking. The depth counter
was avoiding a possible double trip on the global cpuset_sem semaphore. It
worked, but now an improved version of cpuset locking is available, to come
in the next patch, using two global semaphores.
This patch reverses "cpuset semaphore depth check deadlock fix"
The kernel still works, even after this patch, except for some rare and
difficult to reproduce race conditions when agressively creating and
destroying cpusets marked with the notify_on_release option, on very large
systems.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove one more useless line from cpuset_common_file_read().
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes incorrect error path in proc_get_inode(), when module
can't be get due to being unloaded. When try_module_get() fails, this
function puts de(!) and still returns inode with non-getted de.
There are still unresolved known bugs in proc yet to be fixed:
- proc_dir_entry tree is managed without any serialization
- create_proc_entry() doesn't setup de->owner anyhow,
so setting it later manually is inatomic.
- looks like almost all modules do not care whether
it's de->owner is set...
Signed-Off-By: Denis Lunev <den@sw.ru>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove last remains of NFS exportability support.
The code is actually buggy (as reported by Akshat Aranya), since 'alias'
will be leaked if it's non-null and alias->d_flags has DCACHE_DISCONNECTED.
This is not an active bug, since there will never be any disconnected
dentries. But it's better to get rid of the unnecessary complexity anyway.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the recent timer rework we lost the check for an add_timer() of an
already-pending timer. That check was useful for networking, so put it back.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the requested I/O scheduler is already in place, elevator_switch simply
leaves the queue alone, and returns. However, it forgets to call
elevator_put, so
'echo [current_sched] > /sys/block/[dev]/queue/scheduler'
will leak a reference, causing the current_sched module to be permanently
pinned in memory.
Signed-off-by: Nate Diller <nate@namesys.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the pid argument a long as on every other arcihtecture. Despite pid_t
beeing a 32bit type even on 64bit parisc this is not an ABI change due to
the parisc calling conventions. And even if it did it wouldn't matter too
much because 64bit userspace on parisc is in an embrionic stage.
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: I don't do typo patches, but one of these is in a printk string)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a kconfig submenu to select the default I/O scheduler, in case
anticipatory is not compiled in or another default is preferred. Also,
since no-op is always available, we should use it whenever the selected
default is not.
Signed-off-by: Nate Diller <nate@namesys.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The majority of the sys_tkill() and sys_tgkill() function code is
duplicated between the two of them. This patch pulls the duplication out
into a separate function -- do_tkill() -- and lets sys_tkill() and
sys_tgkill() be simple wrappers around it. This should make it easier to
maintain in light of future changes.
Signed-off-by: Vadim Lobanov <vlobanov@speakeasy.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This lock is used in sigqueue_free(), but it is always equal to
current->sighand->siglock, so we don't need to keep it in the struct
sigqueue.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
de_thread() calls del_timer_sync(->real_timer) under ->sighand->siglock.
This is deadlockable, it_real_fn sends a signal and needs this lock too.
Also, delete unneeded ->real_timer.data assignment.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that RCU applied on 'struct file' seems stable, we can place f_rcuhead
in a memory location that is not anymore used at call_rcu(&f->f_rcuhead,
file_free_rcu) time, to reduce the size of this critical kernel object.
The trick I used is to move f_rcuhead and f_list in an union called f_u
The callers are changed so that f_rcuhead becomes f_u.fu_rcuhead and f_list
becomes f_u.f_list
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add explicit text about
- where menuconfig '/' (search) searches for strings,
- that substrings are allowed, and
- that regular expressions are supported.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first two hunks of the patch really belongs in patch 1, but I missed
them on the first pass and instead of redoing all 3 patches I stuck them in
this one.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removes a few pointless register keywords. register is merely a compiler
hint that access to the variable should be optimized, but gcc (3.3.6 in my
case) generates the exact same code with and without the keyword, and even
if gcc did something different with register present I think it is doubtful
we would want to optimize access to these variables - especially since this
is generic library code and there are supposed to be optimized versions in
asm/ for anything that really matters speed wise.
(akpm: iirc, keyword register is a gcc no-op unless using -O0)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removes some blank lines, removes some trailing whitespace, adds spaces
after commas and a few similar changes.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only call to ide_cdrom_capacity is in code protected by
CONFIG_PROC_FS, so when that is not enabled, the compiler complains:
drivers/ide/ide-cd.c:3259: warning: `ide_cdrom_capacity' defined but not used
Here is a patch that fixes that. It provides some space savings for
embedded systems that are not using procfs, as well:
text data bss dec hex filename
- 33540 6504 1032 41076 a074 drivers/ide/ide-cd.o
+ 33468 6480 1032 40980 a014 drivers/ide/ide-cd.o
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
task_struct is an internal structure to the kernel with a lot of good
information, that is probably interesting in core dumps. However there is
no way for user space to know what format that information is in making it
useless.
I grepped the GDB 6.3 source code and NT_TASKSTRUCT while defined is not
used anywhere else. So I would be surprised if anyone notices it is
missing.
In addition exporting kernel pointers to all the interesting kernel data
structures sounds like the very definition of an information leak. I
haven't a clue what someone with evil intentions could do with that
information, but in any attack against the kernel it looks like this is the
perfect tool for aiming that attack.
So since NT_TASKSTRUCT is useless as currently defined and is potentially
dangerous, let's just not export it.
(akpm: Daniel Jacobowitz <dan@debian.org> "would be amazed" if anything was
using NT_TASKSTRUCT).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove timer_list.magic and associated debugging code.
I originally added this when a spinlock was added to timer_list - this meant
that an all-zeroes timer became illegal and init_timer() was required.
That spinlock isn't even there any more, although timer.base must now be
initialised.
I'll keep this debugging code in -mm.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the workqueus use alloc_percpu instead of an array. The
workqueues are placed on nodes local to each processor.
The workqueue structure can grow to a significant size on a system with
lots of processors if this patch is not applied. 64 bit architectures with
all debugging features enabled and configured for 512 processors will not
be able to boot without this patch.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Try to make the INIT_ENV_ARG_LIMIT help text more readable and
understandable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last patch from Jens Axboe for drivers/block/paride/pf.c introduced
pf_end_request() which sets pf_req to NULL.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a macro shift_right() that avoids the numerous ugly conditionals in the
NTP code that look like:
if(a < 0)
b = -(-a >> shift);
else
b = a >> shift;
Replacing it with:
b = shift_right(a, shift);
This should have zero effect on the logic, however it should probably have
a bit of testing just to be sure.
Also replace open-coded min/max with the macros.
Signed-off-by : John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
TIOCSTART and TIOCSTOP are defined in asm/ioctls.h and asm/termios.h by
various architectures but not actually implemented anywhere but in the IRIX
compatibility layer, so remove their COMPATIBLE_IOCTL from parisc, ppc64
and sparc64.
Move the TIOCSLTC COMPATIBLE_IOCTL to common code, guided by an ifdef to
only show up on architectures that support it (same as the code handling it
in tty_ioctl.c), aswell as it's brother TIOCGLTC that wasn't handled so
far.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enhance the kthread API by adding kthread_stop_sem, for use in stopping
threads that spend their idle time waiting on a semaphore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We're trying to get rid of as much as possible tasklist walks, or at
least moving them to core code. This patch falls into the second
category.
Instead of walking the tasklist in cfq-iosched move that into
elv_unregister. The added benefit is that with this change the as
ioscheduler might be might unloadable more easily aswell.
The new code uses read_lock instead of read_lock_irq because the
tasklist_lock only needs irq disabling for writers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every user of init_timer() also needs to initialize ->function and ->data
fields. This patch adds a simple setup_timer() helper for that.
The schedule_timeout() is patched as an example of usage.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the problem (BUG 4964) with unmapped buffers in transaction's
t_sync_data list. The problem is we need to call filesystem's own
invalidatepage() from block_write_full_page().
block_write_full_page() must call filesystem's invalidatepage(). Otherwise
following nasty race can happen:
proc 1 proc 2
------ ------
- write some new data to 'offset'
=> bh gets to the transactions data list
- starts truncate
=> i_size set to new size
- mpage_writepages()
- ext3_ordered_writepage() to 'offset'
- block_write_full_page()
- page->index > end_index+1
- block_invalidatepage()
- discard_buffer()
- clear_buffer_mapped()
- commit triggers and finds unmapped buffer - BOOM!
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smsc-ircc2 - avoid closing network device when suspending; just release
interrupt and disable DMA ourselves. Also make sure to reset chip when
resuming.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@bougret.hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch exports modalias for ccw devices.
So you can do:
modprobe `echo /sys/device/path_to_device/modalias`
and the proper driver will automatically be loaded by userspace.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I just noted that -mtune is used, which is only supported on recent GCCs; by
reading http://gcc.gnu.org/gcc-3.4/changes.html, you see "-mcpu has been
renamed to -mtune.", so for GCC < 3.4 we're not using any specific tuning in
the appropriate cases. However -mcpu is deprecated, so use -mtune when
possible.
This was introduced by commit e9d4dce954a60dc23dd1d967766ca2347b780e54 of the
old tree (between 2.6.10-rc3 and 2.6.10) by Linus Torvalds, to remove the use
of -march, since that could trigger gcc using SSE on its own. But no
attention was used about using -mcpu vs. -mtune.
And btw, the old 2.6.4 code (for instance) was:
cflags-$(CONFIG_MPENTIUMII) += $(call check_gcc,-march=pentium2,-march=i686)
cflags-$(CONFIG_MPENTIUMIII) += $(call check_gcc,-march=pentium3,-march=i686)
cflags-$(CONFIG_MPENTIUMM) += $(call check_gcc,-march=pentium3,-march=i686)
cflags-$(CONFIG_MPENTIUM4) += $(call check_gcc,-march=pentium4,-march=i686)
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was used in the old dark age of 2.4, ARCH_CFLAGS doesn't work any more
since some time, and UM_FASTCALL was never used in 2.6.
Instead, reintroduce the thing more properly now, directly in
include/asm-um/linkage.h.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove RWSEM_GENERIC_SPINLOCK, it's now defined (only if needed) by the
underlying arch/i386/Kconfig.cpu. Leave it only for x86_64. Even there, it's
totally wrong, as they even have the code to support XCHG_ADD.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make UML share the underlying cpu-specific tuning done on i386.
Actually, for now many config options aren't used a lot - but that can be done
later. Also, UML relies on GCC optimization for things like memcpy and such
more than i386, so specifying the correct -march and -mtune should be enough.
Later, we may want to correct some other stuff.
For instance, since FPU context switching, for us, is done (at least
partially, i.e. between our kernelspace and userspace) by the host, we may
allow usage of FPU operations by GCC. This doesn't hold for kernelspace vs.
kernelspace, but we don't support preemption.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update SMC91x driver for m32r.
- Remove needless NONCACHE_OFFSET adjustment.
> [PATCH 2.6.14-rc4] m32r: NONCACHE_OFFSET in _port2addr
> Change _port2addr() not to add NONCACHE_OFFSET.
> Adding NONCACHE_OFFSET requires needless address adjusting by a driver
> using ioremap() like a SMC91x driver.
- Fix lots of warnings as following:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c: In function `smc_reset':
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:324: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:325: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:341: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:342: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change _port2addr() not to add NONCACHE_OFFSET. Adding NONCACHE_OFFSET
requires needless address adjusting by a driver using ioremap() like a
SMC91x driver.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add pm_ops.valid callback, so only the available pm states show in
/sys/power/state. And this also makes an earlier states error report at
enter_state before we do actual suspend/resume.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Acked-by: Pavel Machek<pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch simplifies the progress meter in disk.c:free_some_memory()
and makes disk.c:pm_suspend_disk() call device_resume() explicitly in the
suspend path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch merges two functions in a trivial way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reduce number of ifdefs somehow, and fix whitespace a bit. No real code
changes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp use the PG_nosave and PG_nosave_free flags to
mark pages that should be freed in case of an error during resume.
This allows us to simplify the code and to use swsusp_free() in all of the
swsusp's resume error paths, which makes them actually work.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch moves the functionality of swsusp related to creating and
handling the snapshot of memory to a separate file, snapshot.c
This should enable us to untangle the code in the future and eventually to
implement some parts of swsusp.c in the user space.
The patch does not change the code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch makes swsusp use PG_nosave and PG_nosave_free flags to
mark pages that should be freed after the state of the system has been
restored from the image (or in case of an error during suspend).
This allows us to avoid storing metadata in swap twice and to reduce the
amount of memory needed by swsusp. Additionally, it allows us to simplify
the code by removing a couple of functions that are no longer necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpufreq entries in sysfs should only be populated when CPU is online state.
When we either boot with maxcpus=x and then boot the other cpus by echoing
to sysfs online file, these entries should be created and destroyed when
CPU_DEAD is notified. Same treatement as cache entries under sysfs.
We place the processor in the lowest frequency, so hw managed P-State
transitions can still work on the other threads to save power.
Primary goal was to just make these directories appear/disapper dynamically.
There is one in this patch i had to do, which i really dont like myself but
probably best if someone handling the cpufreq infrastructure could give
this code right treatment if this is not acceptable. I guess its probably
good for the first cut.
- Converting lock_cpu_hotplug()/unlock_cpu_hotplug() to disable/enable preempt.
The locking was smack in the middle of the notification path, when the
hotplug is already holding the lock. I tried another solution to avoid this
so avoid taking locks if we know we are from notification path. The solution
was getting very ugly and i decided this was probably good for this iteration
until someone who understands cpufreq could do a better job than me.
(akpm: export cpucontrol to GPL modules: drivers/cpufreq/cpufreq_stats.c now
does lock_cpu_hotplug())
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu cache entries should be populated only when cpu is online and removed
when they are logically offlined.
Without which entries are not removed when cpu is offlined, or dont appear
when we boot with maxcpus=1 and then kick the rest of the cpus via echo 1
to the sysfs online file.
- Changed __devinit to __cpuinit for consistency.
- Changed sysfs_driver_register to register_cpu_notifier.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some modules creating sysfs entries under /sys/devices/system/cpu/cpuX/
need to know the parent sysfs entry to make devices under them. This will
just return the sysfs entry for a given cpu.
sysfs entries showing under each cpu sysfs can be easily created if such
entries can be created by registering a sysfs driver for cpuclass. The
issue is when the entry is created the CPU may not be online, hence we
would need to defer the creation until the online notification comes.
Current users: cache entries for Intel CPU's and cpufreq subsystem.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a check for the return value of acpi_find_root_pointer().
Without this patch systems without ACPI support such as QEMU crashes when
booting a NUMA kernel with CONFIG_ACPI_SRAT=y.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After staring at mpparse.c for a little longer I noticed that when we hit
our limit of num_processors we are filtering out information about other
processors that we can still store.
This patch just reorders the code so we store everything we can.
This should avoid the incorrect warning about our boot CPU not being listed
by the BIOS that we are now getting in the kexec on panic case, and it
should allow us to detect all apicid conflicts even when our physical
number of cpus exceeds maxcpus.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Removes the unnecessary call to local_irq_disable().
o Kdump was failing while second kernel was coming up. Check for presence
of boot cpu apic id was failing in (apic_id_registered), hence hitting
BUG().
o This should not have failed because before calling setup_local_APIC(), it is
ensured that even if BIOS has not reported boot cpu, then hard set the
prence of it. Problem happens because of usage of hard_smp_processor_id()
which is hardcoded to zero in case of non SMP kernel. In kdump case second
kernel can boot on a cpu whose boot cpu id is not zero.
o Using boot_cpu_physical_apicid instead to hard set the presence of boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle 32-bit mtrr ioctls in the mtrr driver instead of the ia32
compatability layer.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If VMX feature is available in the CPU, this patch will make it visible in
the /proc/cpuinfo with the cpuid detection.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is dangerous to shutdown the apics in machine_crash_shutdown.
With my previous patch to initialize apics in init_IRQ we should be able to
boot a kernel without this. As long as we reinitialize the APICs we don't
care what state they were in during bootup.
This should make machine_crash_shutdown noticeably more reliable.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kinds of ugliness exists because we don't initialize
the apics during init_IRQs.
- We calibrate jiffies in non apic mode even when we are using apics.
- We have to have special code to initialize the apics when non-smp.
- The legacy i8259 must exist and be setup correctly, even
when we won't use it past initialization.
- The kexec on panic code must restore the state of the io_apics.
- init/main.c needs a special case for !smp smp_init on x86
In addition to pure code movement I needed a couple
of non-obvious changes:
- Move setup_boot_APIC_clock into APIC_late_time_init for
simplicity.
- Use cpu_khz to generate a better approximation of loops_per_jiffies
so I can verify the timer interrupt is working.
- Call setup_apic_nmi_watchdog again after cpu_khz is initialized on
the boot cpu.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The per cpu nmi watchdog timer is based on an event counter. idle cpus
don't generate events so the NMI watchdog doesn't fire and the test to see
if the watchdog is working fails.
- Add nmi_cpu_busy so idle cpus don't mess up the test.
- kmalloc prev_nmi_count to keep kernel stack usage bounded.
- Improve the error message on failure so there is enough
information to debug problems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected. This is very
useful when we kexec another kernel and likely helpful when dealing with a
BIOS that make assumptions about how the system is setup.
Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.
Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.
In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0. As
there does not appear to be anything to guarantee that assumption is true.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is platform code update for ES7000: disables IRQ overrides for the
recent ES7000 (Rascal/Zorro), cleans up the compile warning. The patch
only affects the ES7000 subarch.
Signed-off-by: <Natalie.Protasevich@unisys.com>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that prints the cache size assumes that L3 always lives in chipset
and is shared across CPUs. Which is not really true.
I think all the cachesizes reported by cpuid are in the processor itself.
The attached patch changes the code to reflect that.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was reported because someone was getting oopses reading /proc/iomem.
It was tracked down to a zero-sized 'struct resource' entry which was
located right at 4GB.
You need two conditions to hit this bug: a BIOS E820_RAM area starting at
exactly the boundary where you specify mem= (to get a zero-sized entry),
and for the legacy_init_iomem_resources() loop to skip that resource (which
only happens at exactly 4G).
I think the killing zero-sized e820 entry is the easiest way to fix this.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make P6 MCA initialization code complaint with guidelines in IA-32 SDM
Vol3. Bank 0 control register should not be set by OS and clear status
registers on all banks on reset.
This will prevent false MCE alarms on the systems that has some non-MCE
information left-over in MC0_STATUS on reboot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an accessor function for getting the per-CPU gdt. Callee must already
have the CPU.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The per-CPU initialization code is copying in bogus data into
thread->tls_array. Note that it copies &per_cpu(cpu_gdt_table, cpu), not
&per_cpu(cpu_gdt_table, cpu)[GDT_ENTRY_TLS_MIN). That is totally broken
and unnecessary. Make the initialization explicitly NULL.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch allows physical bring-up of new processors (not initially present
in the configuration) from facilities such as driver/utility implemented on
a platform. The actual method of making processors available is up to the
platform implementation.
Signed-off-by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zwane Mwaikambo <zwane@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Join together some common functions (pmd_page{,_kernel}) over 2level and
3level pages.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial internal version of Venki's cpuid(4) deterministic cache parameter
identification patch used static arrays of size MAX_CACHE_LEAVES. Final patch
which made to the base used dynamic array allocation, with this
MAX_CACHE_LEAVES limit hunk still in place.
cpuid(4) already has a mechanism to find out the number of cache levels
implemented and there is no need for this hardcoded MAX_CACHE_LEAVES limit.
So remove the MAX_CACHE_LEAVES limit from the routine which calculates the
number of cache levels using cpuid(4)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There exists a field io_bitmap_owner in the TSS that is only checked, but
never set to anything else but NULL.
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mxcsr_feature_mask_init isn't needed in suspend/resume time (we can use
boot time mask). And actually it's harmful, as it clear task's saved
fxsave in resume. This bug is widely seen by users using zsh.
(akpm: my eyes. Fixed some surrounding whitespace mess)
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts i386's cmpxchg patterns so that
- for word and long cmpxchg-es the compiler can utilize all possible
registers
- cmpxchg8b gets disabled when the minimum specified hardware architectur
doesn't support it (like was already happening for the byte, word, and
long ones).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I just found out that some precision is unnecessarily lost in the
arch/i386/kernel/timers/timer_tsc.c:set_cyc2ns_scale function. It uses a
cpu_mhz parameter when it could use a cpu_khz. In the specific case of an
Intel P4 running at 3001.171 Mhz, the truncation to 3001 Mhz leads to an
imprecision of 19 microseconds per second : this is very sad for a timer with
nearly nanosecond accuracy.
Fix the x86_64 architecture too.
Cc: george anzinger <george@mvista.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes a bunch of unecessary checks for (size_t < 0) in
selinuxfs.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
security/selinux/hooks.c: In function `selinux_inode_getxattr':
security/selinux/hooks.c:2193: warning: unused variable `sbsec'
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows SELinux to canonicalize the value returned from
getxattr() via the security_inode_getsecurity() hook, which is called after
the fs level getxattr() function.
The purpose of this is to allow the in-core security context for an inode
to override the on-disk value. This could happen in cases such as
upgrading a system to a different labeling form (e.g. standard SELinux to
MLS) without needing to do a full relabel of the filesystem.
In such cases, we want getxattr() to return the canonical security context
that the kernel is using rather than what is stored on disk.
The implementation hooks into the inode_getsecurity(), adding another
parameter to indicate the result of the preceding fs-level getxattr() call,
so that SELinux knows whether to compare a value obtained from disk with
the kernel value.
We also now allow getxattr() to work for mountpoint labeled filesystems
(i.e. mount with option context=foo_t), as we are able to return the
kernel value to the user.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts SELinux code from kmalloc/memset to the new kazalloc
unction. On i386, this results in a text saving of over 1K.
Before:
text data bss dec hex filename
86319 4642 15236 106197 19ed5 security/selinux/built-in.o
After:
text data bss dec hex filename
85278 4642 15236 105156 19ac4 security/selinux/built-in.o
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since CONFIG_IKCONFIG_PROC already depends on CONFIG_IKCONFIG, adding
configs.o again is redundant.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compiler warning fix; the inline callers of these APIs were changed
to have const vaddr parameters.
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for pcmcia slot on sharp zaurus sl-5500.
pxa2xx_sharpsl.c thus becomes quite miss-named, but I guess that
is not worth fixing?
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for sharp zaurus sl-5500 touchscreen. It introduces
some not-too-nice ifs, but I guess copying whole ucb1x00-ts.c would be
bad idea...
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Physical addresses are not valid pointers of any sort and should
not be cast to such.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes an issue reported by Coverity in serial/serial_core.c
Error reported: Variable "&((info)->tty)->flags" tracked as NULL was passed to a
function that dereferences it.
The later statements in the function assumes 'info->tty != NULL', so this
check is not necessary. Probably a 'BUG_ON(info->tty == NULL)' can be added.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch gets rid of the last C implementations of needed libgcc
functions for the kernel, replacing them with optimized assembly
versions.
Those functions are:
__ashldi3
__ashrdi3
__lshrdi3
__muldi3
__ucmpdi2
The first 3 were lifted from gcc, the other two were written from scratch.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Encapsulate pool data into dmabounce_pool. Only account successful
allocations. Use dma_mapping_error().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We know what pgprot we're going to use, so don't #define it. Also,
since we select the nonaliasing/aliasing copypage implementation at
run time, there's no point having it globally visible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IMX serial driver to unregister its driver structure
when it is unloaded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Richard Purdie
Update the PXA irda driver to match the recent platform device
suspend/resume level changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a bug where settimeofday would set the wrong parameters
in do_gtod, resulting in gettimeofday returning a value about 4
hours after the correct time. The bug was that we divided a
negative 64-bit value with do_div, which treated it as unsigned
and gave us a result that was approximately 1.8e10 too large
(since the divisor was 1e9).
Signed-off-by: Paul Mackerras <paulus@samba.org>
ata_pci_init_one() receives an array of struct ata_port_info. Recent
updates to the code had always obtained port information from
array element 0, rather than array element N.
Change to avoid hardcoding port_info[0], thereby restoring proper
hardware information to secondary legacy ports.
If a card doesn't support the "write block" command class then
any attempts to open the device should reflect this by denying
write access.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
move EXPORT_SYMBOL(filemap_populate) to the proper place: just after
function itself: it's easy to miss that function is exported otherwise.
Signed-off-by: Nikita Danilov <nikita@clusterfs.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 'mm' change the explicit use of a for-loop using NR_CPUS into the
general for_each_cpu() constructs. This widens the scope of potential
future optimizations of the general constructs, as well as takes advantage
of the existing optimizations of first_cpu() and next_cpu(), which is
advantageous when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Policy contextualization is only useful for task based policies and not for
vma based policies. It may be useful to define allowed nodes that are not
accessible from this thread because other threads may have access to these
nodes. Without this patch strange memory policy situations may cause an
application to fail with out of memory.
Example:
Let's say we have two threads A and B that share the same address space and
a huge array computational array X.
Thread A is restricted by its cpuset to nodes 0 and 1 and thread B is
restricted by its cpuset to nodes 2 and 3.
Thread A now wants to restrict allocations to the first node and thus
applies a BIND policy on X to node 0 and 2. The cpuset limits this to node
0. Thus pages for X must be allocated on node 0 now.
Thread B now touches a page that has never been used in X and faults in a
page. According to the BIND policy of the vma for X the page must be
allocated on page 0. However, the cpuset of B does not allow allocation on
0 and 1. Now the application fails in alloc_pages with out of memory.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Do a separation between do_xxx and sys_xxx functions. sys_xxx functions
take variable sized bitmaps from user space as arguments. do_xxx functions
take fixed sized nodemask_t as arguments and may be used from inside the
kernel. Doing so simplifies the initialization code. There is no
fs = kernel_ds assumption anymore.
- Split up get_nodes into get_nodes (which gets the node list) and
contextualize_policy which restricts the nodes to those accessible
to the task and updates cpusets.
- Add comments explaining limitations of bind policy
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a set of ppc64 specific patches that at least allow
compilation/booting with the following configurations:
FLATMEM
SPARSEMEN
SPARSEMEM + MEMORY_HOTPLUG
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the necessary for non-NUMA hot-add of highmem to an existing zone on
i386.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: IWAMOTO Toshihiro <iwamoto@valinux.co.jp>
> I found the tests does not work well with Dave's patchset.
> I've found the followings:
>
> - setup_per_zone_pages_min() calls should be added in
> capture_page_range() and online_pages()
> - lru_add_drain() should be called before try_to_migrate_pages()
The following patch deals with the first item.
Signed-off-by: IWAMOTO Toshihiro <iwamoto@valinux.co.jp>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This basically keeps up from having to extern __kmalloc_section_memmap().
The vaddr_in_vmalloc_area() helper could go in a vmalloc header, but that
header gets hard to work with, because it needs some arch-specific macros.
Just stick it in here for now, instead of creating another header.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Lion Vollnhals <webmaster@schiggl.de>
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds generic memory add/remove and supporting functions for memory
hotplug into a new file as well as a memory hotplug kernel config option.
Individual architecture patches will follow.
For now, disable memory hotplug when swsusp is enabled. There's a lot of
churn there right now. We'll fix it up properly once it calms down.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
See the "fixup bad_range()" patch for more information, but this actually
creates a the lock to protect things making assumptions about a zone's size
staying constant at runtime.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pgdat->node_size_lock is basically only neeeded in one place in the normal
code: show_mem(), which is the arch-specific sysrq-m printing function.
Strictly speaking, the architectures not doing memory hotplug do no need this
locking in show_mem(). However, they are all included for completeness. This
should also make any future consolidation of all of the implementations a
little more straightforward.
This lock is also held in the sparsemem code during a memory removal, as
sections are invalidated. This is the place there pfn_valid() is made false
for a memory area that's being removed. The lock is only required when doing
pfn_valid() operations on memory which the user does not already have a
reference on the page, such as in show_mem().
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When doing memory hotplug operations, the size of existing zones can obviously
change. This means that zone->zone_{start_pfn,spanned_pages} can change.
There are currently no locks that protect these structure members. However,
they are rarely accessed at runtime. Outside of swsusp, the only place that I
can find is bad_range().
So, split bad_range() up into two pieces: one that needs to be locked and
anther that doesn't.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a zone is empty at boot-time and then hot-added to later, it needs to run
the same init code that would have been run on it at boot.
This patch breaks out zone table and per-cpu-pages functions for use by the
hotplug code. You can almost see all of the free_area_init_core() function on
one page now. :)
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following series implements memory hot-add for ppc64 and i386. There are
x86_64 and ia64 implementations that will be submitted shortly as well,
through the normal maintainers.
This patch:
local_mapnr is unused, except for in an alpha header. Keep the alpha one,
kill the rest.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a problem on ppc64 where with more than 4 threads a large system
wouldn't scale well while faulting in the .text (most of the time was spent
in the kernel despite it was an userland compute intensive app). The
reason is the useless overwrite of the same pte from all cpu.
I fixed it this way (verified on an older kernel but the forward port is
almost identical). This will benefit all archs not just ppc64.
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Basic overcommit checking for hugetlb_file_map() based on an implementation
used with demand faulting in SLES9.
Since demand faulting can't guarantee the availability of pages at mmap
time, this patch implements a basic sanity check to ensure that the number
of huge pages required to satisfy the mmap are currently available.
Despite the obvious race, I think it is a good start on doing proper
accounting. I'd like to work towards an accounting system that mimics the
semantics of normal pages (especially for the MAP_PRIVATE/COW case). That
work is underway and builds on what this patch starts.
Huge page shared memory segments are simpler and still maintain their
commit on shmget semantics.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Below is a patch to implement demand faulting for huge pages. The main
motivation for changing from prefaulting to demand faulting is so that huge
page memory areas can be allocated according to NUMA policy.
Thanks to consolidated hugetlb code, switching the behavior requires changing
only one fault handler. The bulk of the patch just moves the logic from
hugelb_prefault() to hugetlb_pte_fault() and find_get_huge_page().
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up some repeated code related to HugeTLB. hugetlb_zero_setup would
have already allocated the file->f_op.
Signed-off-by: Krishnakumar. R <rkrishnakumar@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reformat hugelbfs_forget_inode and add the missing but harmless
write_inode_now call. It looks the same as generic_forget_inode now except
for the call to truncate_hugepages instead of truncate_inode_pages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hugetlbfs_do_delete_inode is the same as generic_delete_inode now, so remove
it in favour of the latter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make hugetlbfs looks the same as generic_detelte_inode, fixing a bunch of
missing updates to it at the same time. Rename it to
hugetlbfs_do_delete_inode and add a real hugetlbfs_delete_inode that
implements ->delete_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move hugetlbfs accounting into ->alloc_inode / ->destroy_inode. This keeps
the code simpler, fixes a loeak where a failing inode allocation wouldn't
decrement the counter and moves hugetlbfs_delete_inode and
hugetlbfs_forget_inode closer to their generic counterparts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated several references to page_table_lock in common code comments.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of oddities were guarded by page_table_lock, no longer properly
guarded when that is split.
The mm_counters of file_rss and anon_rss: make those an atomic_t, or an
atomic64_t if the architecture supports it, in such a case. Definitions by
courtesy of Christoph Lameter: who spent considerable effort on more scalable
ways of counting, but found insufficient benefit in practice.
And adding an mm with swap to the mmlist for swapoff: the list is well-
guarded by its own lock, but the list_empty check now has to be repeated
inside it.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Christoph Lameter demonstrated very poor scalability on the SGI 512-way, with
a many-threaded application which concurrently initializes different parts of
a large anonymous area.
This patch corrects that, by using a separate spinlock per page table page, to
guard the page table entries in that page, instead of using the mm's single
page_table_lock. (But even then, page_table_lock is still used to guard page
table allocation, and anon_vma allocation.)
In this implementation, the spinlock is tucked inside the struct page of the
page table page: with a BUILD_BUG_ON in case it overflows - which it would in
the case of 32-bit PA-RISC with spinlock debugging enabled.
Splitting the lock is not quite for free: another cacheline access. Ideally,
I suppose we would use split ptlock only for multi-threaded processes on
multi-cpu machines; but deciding that dynamically would have its own costs.
So for now enable it by config, at some number of cpus - since the Kconfig
language doesn't support inequalities, let preprocessor compare that with
NR_CPUS. But I don't think it's worth being user-configurable: for good
testing of both split and unsplit configs, split now at 4 cpus, and perhaps
change that to 8 later.
There is a benefit even for singly threaded processes: kswapd can be attacking
one part of the mm while another part is busy faulting.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In worrying over the various pte operations in different architectures, I came
across some unused functions in UML: remove mprotect_kernel_vm,
protect_vm_page and addr_pte.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's usually a good reason when a pte is examined without the lock; but it
makes me nervous when the pointer is dereferenced more than once.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The cris v32 switch_mm guards get_mmu_context with next->page_table_lock: good
it's not really SMP yet, since get_mmu_context messes with global variables
affecting other mms. Replace by global mmu_context_lock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a worrying function translation_exists in parisc cacheflush.h,
unaffected by split ptlock since flush_dcache_page is using it on some other
mm, without any relevant lock. Oh well, make it a slightly more robust by
factoring the pfn check within it. And it looked liable to confuse a
camouflaged swap or file entry with a good pte: fix that too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prepare arm for the split page_table_lock: three issues.
Signal handling's preserve and restore of iwmmxt context currently involves
reading and writing that context to and from user space, while holding
page_table_lock to secure the user page(s) against kswapd. If we split the
lock, then the structure might span two pages, secured by to read into and
write from a kernel stack buffer, copying that out and in without locking (the
structure is 160 bytes in size, and here we're near the top of the kernel
stack). Or would the overhead be noticeable?
arm_syscall's cmpxchg emulation use pte_offset_map_lock, instead of
pte_offset_map and mm-wide page_table_lock; and strictly, it should now also
take mmap_sem before descending to pmd, to guard against another thread
munmapping, and the page table pulled out beneath this thread.
Updated two comments in fault-armv.c. adjust_pte is interesting, since its
modification of a pte in one part of the mm depends on the lock held when
calling update_mmu_cache for a pte in some other part of that mm. This can't
be done with a split page_table_lock (and we've already taken the lowest lock
in the hierarchy here): so we'll have to disable split on arm, unless
CONFIG_CPU_CACHE_VIPT to ensures adjust_pte never used.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use pte_offset_map_lock, instead of pte_offset_map (or inappropriate
pte_offset_kernel) and mm-wide page_table_lock, in sundry arch places.
The i386 vm86 mark_screen_rdonly: yes, there was and is an assumption that the
screen fits inside the one page table, as indeed it does.
The sh __do_page_fault: which handles both kernel faults (without lock) and
user mm faults (locked - though it set_pte without locking before).
The sh64 flush_cache_range and helpers: which wrongly thought callers held
page_table_lock before (only its tlb_start_vma did, and no longer does so);
moved the flush loop down, and adjusted the large versus small range decision
to consider a range which spans page tables as large.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Final step in pushing down common core's page_table_lock. follow_page no
longer wants caller to hold page_table_lock, uses pte_offset_map_lock itself;
and so no page_table_lock is taken in get_user_pages itself.
But get_user_pages (and get_futex_key) do then need follow_page to pin the
page for them: take Daniel's suggestion of bitflags to follow_page.
Need one for WRITE, another for TOUCH (it was the accessed flag before:
vanished along with check_user_page_readable, but surely get_numa_maps is
wrong to mark every page it finds as accessed), another for GET.
And another, ANON to dispose of untouched_anonymous_page: it seems silly for
that to descend a second time, let follow_page observe if there was no page
table and return ZERO_PAGE if so. Fix minor bug in that: check VM_LOCKED -
make_pages_present ought to make readonly anonymous present.
Give get_numa_maps a cond_resched while we're there.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_user_page_readable is a problematic variant of follow_page. It's used
only by oprofile's i386 and arm backtrace code, at interrupt time, to
establish whether a userspace stackframe is currently readable.
This is problematic, because we want to push the page_table_lock down inside
follow_page, and later split it; whereas oprofile is doing a spin_trylock on
it (in the i386 case, forgotten in the arm case), and needs that to pin
perhaps two pages spanned by the stackframe (which might be covered by
different locks when we split).
I think oprofile is going about this in the wrong way: it doesn't need to know
the area is readable (neither i386 nor arm uses read protection of user
pages), it doesn't need to pin the memory, it should simply
__copy_from_user_inatomic, and see if that succeeds or not. Sorry, but I've
not got around to devising the sparse __user annotations for this.
Then we can eliminate check_user_page_readable, and return to a single
follow_page without the __follow_page variants.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
rmap's page_check_address descend without page_table_lock. First just
pte_offset_map in case there's no pte present worth locking for, then take
page_table_lock for the full check, and pass ptl back to caller in the same
style as pte_offset_map_lock. __xip_unmap, page_referenced_one and
try_to_unmap_one use pte_unmap_unlock. try_to_unmap_cluster also.
page_check_address reformatted to avoid progressive indentation. No use is
made of its one error code, return NULL when it fails.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small fix to the PageReserved patch: the mips ZERO_PAGE(address) depends on
address, so __xip_unmap is wrong to initialize page with that before address
is initialized; and in fact must re-evaluate it each iteration.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the page_table_lock from around the calls to unmap_vmas, and replace
the pte_offset_map in zap_pte_range by pte_offset_map_lock: all callers are
now safe to descend without page_table_lock.
Don't attempt fancy locking for hugepages, just take page_table_lock in
unmap_hugepage_range. Which makes zap_hugepage_range, and the hugetlb test in
zap_page_range, redundant: unmap_vmas calls unmap_hugepage_range anyway. Nor
does unmap_vmas have much use for its mm arg now.
The tlb_start_vma and tlb_end_vma in unmap_page_range are now called without
page_table_lock: if they're implemented at all, they typically come down to
flush_cache_range (usually done outside page_table_lock) and flush_tlb_range
(which we already audited for the mprotect case).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In most places the descent from pgd to pud to pmd to pte holds mmap_sem
(exclusively or not), which ensures that free_pgtables cannot be freeing page
tables from any level at the same time. But truncation and reverse mapping
descend without mmap_sem.
No problem: just make sure that a vma is unlinked from its prio_tree (or
nonlinear list) and from its anon_vma list, after zapping the vma, but before
freeing its page tables. Then neither vmtruncate nor rmap can reach that vma
whose page tables are now volatile (nor do they need to reach it, since all
its page entries have been zapped by this stage).
The i_mmap_lock and anon_vma->lock already serialize this correctly; but the
locking hierarchy is such that we cannot take them while holding
page_table_lock. Well, we're trying to push that down anyway. So in this
patch, move anon_vma_unlink and unlink_file_vma into free_pgtables, at the
same time as moving page_table_lock around calls to unmap_vmas.
tlb_gather_mmu and tlb_finish_mmu then fall outside the page_table_lock, but
we made them preempt_disable and preempt_enable earlier; and a long source
audit of all the architectures has shown no problem with removing
page_table_lock from them. free_pgtables doesn't need page_table_lock for
itself, nor for what it calls; tlb->mm->nr_ptes is usually protected by
page_table_lock, but partly by non-exclusive mmap_sem - here it's decremented
with exclusive mmap_sem, or mm_users 0. update_hiwater_rss and
vm_unacct_memory don't need page_table_lock either.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was one small but very significant change in the previous patch:
mprotect's flush_tlb_range fell outside the page_table_lock: as it is in 2.4,
but that doesn't prove it safe in 2.6.
On some architectures flush_tlb_range comes to the same as flush_tlb_mm, which
has always been called from outside page_table_lock in dup_mmap, and is so
proved safe. Others required a deeper audit: I could find no reliance on
page_table_lock in any; but in ia64 and parisc found some code which looks a
bit as if it might want preemption disabled. That won't do any actual harm,
so pending a decision from the maintainers, disable preemption there.
Remove comments on page_table_lock from flush_tlb_mm, flush_tlb_range and
flush_tlb_page entries in cachetlb.txt: they were rather misleading (what
generic code does is different from what usually happens), the rules are now
changing, and it's not yet clear where we'll end up (will the generic
tlb_flush_mmu happen always under lock? never under lock? or sometimes under
and sometimes not?).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert those common loops using page_table_lock on the outside and
pte_offset_map within to use just pte_offset_map_lock within instead.
These all hold mmap_sem (some exclusively, some not), so at no level can a
page table be whipped away from beneath them. But whereas pte_alloc loops
tested with the "atomic" pmd_present, these loops are testing with pmd_none,
which on i386 PAE tests both lower and upper halves.
That's now unsafe, so add a cast into pmd_none to test only the vital lower
half: we lose a little sensitivity to a corrupt middle directory, but not
enough to worry about. It appears that i386 and UML were the only
architectures vulnerable in this way, and pgd and pud no problem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the page fault path, the patch before last pushed acquiring the
page_table_lock down to the head of handle_pte_fault (though it's also taken
and dropped earlier when a new page table has to be allocated).
Now delete that line, read "entry = *pte" without it, and go off to this or
that page fault handler on the basis of this unlocked peek. Usually the
handler can proceed without the lock, relying on the subsequent locked
pte_same or pte_none test to back out when necessary; though do_wp_page needs
the lock immediately, and do_file_page doesn't check (if there's a race,
install_page just zaps the entry and reinstalls it).
But on those architectures (notably i386 with PAE) whose pte is too big to be
read atomically, if SMP or preemption is enabled, do_swap_page and
do_file_page might cause irretrievable damage if passed a Frankenstein entry
stitched together from unrelated parts. In those configs, "pte_unmap_same"
has to take page_table_lock, validate orig_pte still the same, and drop
page_table_lock before unmapping, before proceeding.
Use pte_offset_map_lock and pte_unmap_unlock throughout the handlers; but lock
avoidance leaves more lone maps and unmaps than elsewhere.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert those few architectures which are calling pud_alloc, pmd_alloc,
pte_alloc_map on a user mm, not to take the page_table_lock first, nor drop it
after. Each of these can continue to use pte_alloc_map, no need to change
over to pte_alloc_map_lock, they're neither racy nor swappable.
In the sparc64 io_remap_pfn_range, flush_tlb_range then falls outside of the
page_table_lock: that's okay, on sparc64 it's like flush_tlb_mm, and that has
always been called from outside of page_table_lock in dup_mmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Second step in pushing down the page_table_lock. Remove the temporary
bridging hack from __pud_alloc, __pmd_alloc, __pte_alloc: expect callers not
to hold page_table_lock, whether it's on init_mm or a user mm; take
page_table_lock internally to check if a racing task already allocated.
Convert their callers from common code. But avoid coming back to change them
again later: instead of moving the spin_lock(&mm->page_table_lock) down,
switch over to new macros pte_alloc_map_lock and pte_unmap_unlock, which
encapsulate the mapping+locking and unlocking+unmapping together, and in the
end may use alternatives to the mm page_table_lock itself.
These callers all hold mmap_sem (some exclusively, some not), so at no level
can a page table be whipped away from beneath them; and pte_alloc uses the
"atomic" pmd_present to test whether it needs to allocate. It appears that on
all arches we can safely descend without page_table_lock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems odd to me that, whereas pud_alloc and pmd_alloc test inline, only
calling out-of-line __pud_alloc __pmd_alloc if allocation needed,
pte_alloc_map and pte_alloc_kernel are entirely out-of-line. Though it does
add a little to kernel size, change them to macros testing inline, calling
__pte_alloc or __pte_alloc_kernel to allocate out-of-line. Mark none of them
as fastcalls, leave that to CONFIG_REGPARM or not.
It also seems more natural for the out-of-line functions to leave the offset
calculation and map to the inline, which has to do it anyway for the common
case. At least mremap move wants __pte_alloc without _map.
Macros rather than inline functions, certainly to avoid the header file issues
which arise from CONFIG_HIGHPTE needing kmap_types.h, but also in case any
architectures I haven't built would have other such problems.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64 has expand_backing_store function for growing its Register Backing Store
vma upwards. But more complete code for this purpose is found in the
CONFIG_STACK_GROWSUP part of mm/mmap.c. Uglify its #ifdefs further to provide
expand_upwards for ia64 as well as expand_stack for parisc.
The Register Backing Store vma should be marked VM_ACCOUNT. Implement the
intention of growing it only a page at a time, instead of passing an address
outside of the vma to handle_mm_fault, with unknown consequences.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Slight and timid rearrangement of mm_struct: hiwater_rss and hiwater_vm were
tacked on the end, but it seems better to keep them near _file_rss, _anon_rss
and total_vm, in the same cacheline on those arches verified.
There are likely to be more profitable rearrangements, but less obvious (is it
good or bad that saved_auxv[AT_VECTOR_SIZE] isolates cpu_vm_mask and context
from many others?), needing serious instrumentation.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
update_mem_hiwater has attracted various criticisms, in particular from those
concerned with mm scalability. Originally it was called whenever rss or
total_vm got raised. Then many of those callsites were replaced by a timer
tick call from account_system_time. Now Frank van Maarseveen reports that to
be found inadequate. How about this? Works for Frank.
Replace update_mem_hiwater, a poor combination of two unrelated ops, by macros
update_hiwater_rss and update_hiwater_vm. Don't attempt to keep
mm->hiwater_rss up to date at timer tick, nor every time we raise rss (usually
by 1): those are hot paths. Do the opposite, update only when about to lower
rss (usually by many), or just before final accounting in do_exit. Handle
mm->hiwater_vm in the same way, though it's much less of an issue. Demand
that whoever collects these hiwater statistics do the work of taking the
maximum with rss or total_vm.
And there has been no collector of these hiwater statistics in the tree. The
new convention needs an example, so match Frank's usage by adding a VmPeak
line above VmSize to /proc/<pid>/status, and also a VmHWM line above VmRSS
(High-Water-Mark or High-Water-Memory).
There was a particular anomaly during mremap move, that hiwater_vm might be
captured too high. A fleeting such anomaly remains, but it's quickly
corrected now, whereas before it would stick.
What locking? None: if the app is racy then these statistics will be racy,
it's not worth any overhead to make them exact. But whenever it suits,
hiwater_vm is updated under exclusive mmap_sem, and hiwater_rss under
page_table_lock (for now) or with preemption disabled (later on): without
going to any trouble, minimize the time between reading current values and
updating, to minimize those occasions when a racing thread bumps a count up
and back down in between.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There used to be just one call to zap_pte, but it shouldn't be inline now
there are two. Check for the common case pte_none before calling, and move
its rss accounting up into install_page or install_file_pte - which helps the
next patch.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: relieve do_mremap from its surfeit of current->mms.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small adjustment: do_swap_page should report its !pte_same race as a major
fault if it had to read into swap cache, because whatever raced with it will
have found page already in cache and reported minor fault.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small adjustment: zap_pte_range decrement its rss counts from 0 then finally
add, avoiding negations - we don't have or need a sub_mm_rss.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small adjustment, following Nick's suggestion: it's more straightforward for
copy_pte_range to let copy_one_pte do the rss incrementation, than use an
index it passed back. Saves a #define, and 16 bytes of .text.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove PageReserved() calls from core code by tightening VM_RESERVED
handling in mm/ to cover PageReserved functionality.
PageReserved special casing is removed from get_page and put_page.
All setting and clearing of PageReserved is retained, and it is now flagged
in the page_alloc checks to help ensure we don't introduce any refcount
based freeing of Reserved pages.
MAP_PRIVATE, PROT_WRITE of VM_RESERVED regions is tentatively being
deprecated. We never completely handled it correctly anyway, and is be
reintroduced in future if required (Hugh has a proof of concept).
Once PageReserved() calls are removed from kernel/power/swsusp.c, and all
arch/ and driver code, the Set and Clear calls, and the PG_reserved bit can
be trivially removed.
Last real user of PageReserved is swsusp, which uses PageReserved to
determine whether a struct page points to valid memory or not. This still
needs to be addressed (a generic page_is_ram() should work).
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap (and
thus mapcounted and count towards shared rss). These writes to the struct
page could cause excessive cacheline bouncing on big systems. There are a
number of ways this could be addressed if it is an issue.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Refcount bug fix for filemap_xip.c
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Please, please now delete the Atari CONFIG_STRAM_SWAP code. It may be
excellent and ingenious code, but its reference to swap_vfsmnt betrays that it
hasn't been built since 2.5.1 (four years old come December), it's delving
deep into matters which are the preserve of core mm code, its only purpose is
to give the more conscientious mm guys an anxiety attack from time to time;
yet we keep on breaking it more and more.
If you want to use RAM for swap, then if the MTD driver does not already
provide just what you need, I'm sure David could be persuaded to add the
extra. But you'd also like to be able to allocate extents of that swap for
other use: we can give you a core interface for that if you need. But unbuilt
for four years suggests to me that there's no need at all.
I cannot swear the patch below won't break your build, but believe so.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The sh64 hugetlbpage.c seems to be erroneous, left over from a bygone age,
clashing with the common hugetlb.c. Replace it by a copy of the sh
hugetlbpage.c. Except, delete that mk_pte_huge macro neither uses.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One anomaly remains from when Andrea rationalized the responsibilities of
mmap_sem and page_table_lock: in dup_mmap we add vmas to the child holding its
page_table_lock, but not the mmap_sem which normally guards the vma list and
rbtree. Which could be an issue for unuse_mm: though since it just walks down
the list (today with page_table_lock, tomorrow not), it's probably okay. Will
need a memory barrier? Oh, keep it simple, Nick and I agreed, no harm in
taking child's mmap_sem here.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the parent's oldmm throughout dup_mmap, instead of perversely going back
to current->mm. (Can you hear the sigh of relief from those mpnts? Usually I
squash them, but not today.)
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tlb_finish_mmu used to batch zap_pte_range's update of mm rss, which may be
worthwhile if the mm is contended, and would reduce atomic operations if the
counts were atomic. Let zap_pte_range now batch its updates to file_rss and
anon_rss, per page-table in case we drop the lock outside; and copy_pte_range
batch them too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I was lazy when we added anon_rss, and chose to change as few places as
possible. So currently each anonymous page has to be counted twice, in rss
and in anon_rss. Which won't be so good if those are atomic counts in some
configurations.
Change that around: keep file_rss and anon_rss separately, and add them
together (with get_mm_rss macro) when the total is needed - reading two
atomics is much cheaper than updating two atomics. And update anon_rss
upfront, typically in memory.c, not tucked away in page_add_anon_rmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
How is anon_rss initialized? In dup_mmap, and by mm_alloc's memset; but
that's not so good if an mm_counter_t is a special type. And how is rss
initialized? By set_mm_counter, all over the place. Come on, we just need to
initialize them both at once by set_mm_counter in mm_init (which follows the
memcpy when forking).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
zap_pte_range has been counting the pages it frees in tlb->freed, then
tlb_finish_mmu has used that to update the mm's rss. That got stranger when I
added anon_rss, yet updated it by a different route; and stranger when rss and
anon_rss became mm_counters with special access macros. And it would no
longer be viable if we're relying on page_table_lock to stabilize the
mm_counter, but calling tlb_finish_mmu outside that lock.
Remove the mmu_gather's freed field, let tlb_finish_mmu stick to its own
business, just decrement the rss mm_counter in zap_pte_range (yes, there was
some point to batching the update, and a subsequent patch restores that). And
forget the anal paranoia of first reading the counter to avoid going negative
- if rss does go negative, just fix that bug.
Remove the mmu_gather's flushes and avoided_flushes from arm and arm26: no use
was being made of them. But arm26 alone was actually using the freed, in the
way some others use need_flush: give it a need_flush. arm26 seems to prefer
spaces to tabs here: respect that.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tlb_is_full_mm? What does that mean? The TLB is full? No, it means that the
mm's last user has gone and the whole mm is being torn down. And it's an
inline function because sparc64 uses a different (slightly better)
"tlb_frozen" name for the flag others call "fullmm".
And now the ptep_get_and_clear_full macro used in zap_pte_range refers
directly to tlb->fullmm, which would be wrong for sparc64. Rather than
correct that, I'd prefer to scrap tlb_is_full_mm altogether, and change
sparc64 to just use the same poor name as everyone else - is that okay?
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tlb_gather_mmu dates from before kernel preemption was allowed, and uses
smp_processor_id or __get_cpu_var to find its per-cpu mmu_gather. That works
because it's currently only called after getting page_table_lock, which is not
dropped until after the matching tlb_finish_mmu. But don't rely on that, it
will soon change: now disable preemption internally by proper get_cpu_var in
tlb_gather_mmu, put_cpu_var in tlb_finish_mmu.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Speeding up mremap's moving of ptes has never been a priority, but the locking
will get more complicated shortly, and is already too baroque.
Scrap the current one-by-one moving, do an extent at a time: curtailed by end
of src and dst pmds (have to use PMD_SIZE: the way pmd_addr_end gets elided
doesn't match this usage), and by latency considerations.
One nice property of the old method is lost: it never allocated a page table
unless absolutely necessary, so you could free empty page tables by mremapping
to and fro. Whereas this way, it allocates a dst table wherever there was a
src table. I keep diving in to reinstate the old behaviour, then come out
preferring not to clutter how it now is.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Impose a little more consistency on the page fault handlers do_wp_page,
do_swap_page, do_anonymous_page, do_no_page, do_file_page: why not pass their
arguments in the same order, called the same names?
break_cow is all very well, but what it did was inlined elsewhere: easier to
compare if it's brought back into do_wp_page.
do_file_page's fallback to do_no_page dates from a time when we were testing
pte_file by using it wherever possible: currently it's peculiar to nonlinear
vmas, so just check that. BUG_ON if not? Better not, it's probably page
table corruption, so just show the pte: hmm, there's a pte_ERROR macro, let's
use that for do_wp_page's invalid pfn too.
Hah! Someone in the ppc64 world noticed pte_ERROR was unused so removed it:
restored (and say "pud" not "pmd" in its pud_ERROR).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
exit_mmap resets various mm_struct fields, but the mm is well on its way out,
and none of those fields matter by this point.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Divide remove_vm_struct into two parts: first anon_vma_unlink plus
unlink_file_vma, to unlink the vma from the list and tree by which rmap or
vmtruncate might find it; then remove_vma to close, fput and free.
The intention here is to do the anon_vma_unlink and unlink_file_vma earlier,
in free_pgtables before freeing any page tables: so we can be sure that any
page tables traversed by rmap and vmtruncate are stable (and other, ordinary
cases are stabilized by holding mmap_sem).
This will be crucial to traversing pgd,pud,pmd without page_table_lock. But
testing the split-out patch showed that lifting the page_table_lock is
symbiotically necessary to make this change - the lock ordering is wrong to
move those unlinks into free_pgtables while it's under ptlock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
unmap_vma doesn't amount to much, let's put it inside unmap_vma_list. Except
it doesn't unmap anything, unmap_region just did the unmapping: rename it to
remove_vma_list.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The original vm_stat_account has fallen into disuse, with only one user, and
only one user of vm_stat_unaccount. It's easier to keep track if we convert
them all to __vm_stat_account, then free it from its __shackles.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_anonymous_page's pte_wrprotect causes some confusion: in such a case,
vm_page_prot must already be forcing COW, so must omit write permission, and
so the pte_wrprotect is redundant. Replace it by a comment to that effect,
and reword the comment on unuse_pte which also caused confusion.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
zap_pte_range already avoids wasting time to mark_page_accessed on anon pages:
it can also skip anon set_page_dirty - the page only needs to be marked dirty
if shared with another mm, but that will say pte_dirty too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use latency breaking in msync_pte_range like that in copy_pte_range, instead
of the ugly CONFIG_PREEMPT filemap_msync alternatives.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My latency breaking in copy_pte_range didn't work as intended: instead of
checking at regularish intervals, after the first interval it checked every
time around the loop, too impatient to be preempted. Fix that.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds some stack dumps if the slab logic is processing slab
blocks from the wrong node. This is necessary in order to detect
situations as encountered by Petr.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Martin Hicks' page cache reclaim patch added the 'may_swap' flag to the
scan_control struct; and modified shrink_list() not to add anon pages to
the swap cache if may_swap is not asserted.
Ref: http://marc.theaimsgroup.com/?l=linux-mm&m=111461480725322&w=4
However, further down, if the page is mapped, shrink_list() calls
try_to_unmap() which will call try_to_unmap_one() via try_to_unmap_anon ().
try_to_unmap_one() will BUG_ON() an anon page that is NOT in the swap
cache. Martin says he never encountered this path in his testing, but
agrees that it might happen.
This patch modifies shrink_list() to skip anon pages that are not already
in the swap cache when !may_swap, rather than just not adding them to the
cache.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is not problem actually, but sync_page_range() is using for exported
function to filesystems.
The msync_xxx is more readable at least to me.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of them can never be triggered and were only for development.
Signed-off-by: "Andi Kleen" <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The NUMA policy code predated nodemask_t so it used open coded bitmaps.
Convert everything to nodemask_t. Big patch, but shouldn't have any actual
behaviour changes (except I removed one unnecessary check against
node_online_map and one unnecessary BUG_ON)
Signed-off-by: "Andi Kleen" <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set the low water mark for hot pages in pcp to zero.
(akpm: for the life of me I cannot remember why we created pcp->low. Neither
can Martin and the changelog is silent. Maybe it was just a brainfart, but I
have this feeling that there was a reason. If not, we should remove the
fields completely. We'll see.)
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increase the page allocator's per-cpu magazines from 1/4MB to 1/2MB.
Over 100+ runs for a workload, the difference in mean is about 2%. The best
results for both are almost same. Though the max variation in results with
1/2MB is only 2.2%, whereas with 1/4MB it is 12%.
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that the original swap token implementation, by Song Jiang, only
enforced the swap token while the task holding the token is handling a page
fault. This patch approximates that, without adding an additional flag to the
mm_struct, by checking whether the mm->mmap_sem is held for reading, like the
page fault code does.
This patch has the effect of automatically, and gradually, disabling the
enforcement of the swap token when there is little or no paging going on, and
"turning up" the intensity of the swap token code the more the task holding
the token is thrashing.
Thanks to Song Jiang for pointing out this aspect of the token based thrashing
control concept.
The new code shows a slight degradation over the old swap token code, but
still a big win over running without the swap token.
2.6.12+ swap token disabled
$ for i in `seq 10` ; do /usr/bin/time ./qsbench -n 30000000 -p 3 ; done
101.74user 23.13system 8:26.91elapsed 24%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (38597major+430315minor)pagefaults 0swaps
101.98user 24.91system 8:03.06elapsed 26%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (33939major+430457minor)pagefaults 0swaps
101.93user 22.12system 7:34.90elapsed 27%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (33166major+421267minor)pagefaults 0swaps
101.82user 22.38system 8:31.40elapsed 24%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (39338major+433262minor)pagefaults 0swaps
2.6.12+ swap token enabled, timeout 300 seconds
$ for i in `seq 4` ; do /usr/bin/time ./qsbench -n 30000000 -p 3 ; done
102.58user 16.08system 3:41.44elapsed 53%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (19707major+285786minor)pagefaults 0swaps
102.07user 19.56system 4:00.64elapsed 50%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (19012major+299259minor)pagefaults 0swaps
102.64user 18.25system 4:07.31elapsed 48%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (21990major+304831minor)pagefaults 0swaps
101.39user 19.41system 5:15.81elapsed 38%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (24850major+323321minor)pagefaults 0swaps
2.6.12+ with new swap token code, timeout 300 seconds
$ for i in `seq 4` ; do /usr/bin/time ./qsbench -n 30000000 -p 3 ; done
101.87user 24.66system 5:53.20elapsed 35%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (26848major+363497minor)pagefaults 0swaps
102.83user 19.95system 4:17.25elapsed 47%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (19946major+305722minor)pagefaults 0swaps
102.09user 19.46system 5:12.57elapsed 38%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (25461major+334994minor)pagefaults 0swaps
101.67user 20.61system 4:52.97elapsed 41%CPU (0avgtext+0avgdata 0maxresident)k
0inputs+0outputs (22190major+329508minor)pagefaults 0swaps
Signed-off-by: Rik Van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add sem_is_read/write_locked functions to the read/write semaphores, along the
same lines of the *_is_locked spinlock functions. The swap token tuning patch
uses sem_is_read_locked; sem_is_write_locked is added for completeness.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
barrier.h uses barrier() in non-SMP case. And doesn't include compiler.h.
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds
vmalloc_node(size, node) -> Allocate necessary memory on the specified node
and
get_vm_area_node(size, flags, node)
and the other functions that it depends on.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The cipher code relies on the fact that the block size is a multiple
of the required alignment. So we should check this at the time of
algorith registration. We also ensure that the block size is bounded
by the page size.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch rewrites various occurences of &sg[0] where sg is an array
of length one to simply sg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sg_init_one is a nice tool for the block layer. However, users
of struct scatterlist in other subsystems don't usually need the
DMA attributes. For them it's a waste of time and space to
initialise the whole struct scatterlist structure.
Therefore this patch adds a new function sg_set_buf to initialise
a scatterlist without zeroing the DMA attributes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following patch removes the dependency of the fec_8xx driver on
the NETTA & NETPHONE boards. Other people use the driver too, and
we await their board support patches.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patches fixes a bug with erroneous calling of
dma_unmap_single. It never triggered because on normal ppc32
the calls is a NOP. Out of tree drivers need this fix however.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* MII registers must override strap pins
* disable "echo" mode to make 10/HDX work (Franz Sirl)
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For some reason, the hardware designers made the polarity of one bit
in the 440SPe's PHY interface register the opposite of all other PPC
440 chips. To handle this, abstract our access to this bit and do the
right thing based on the configured CPU type.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use spin_trylock_irqsave() in ipoib_start_xmit() instead of
reinventing it out of local_irq_save(), spin_trylock() and
local_irq_restore().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Patch from Nicolas Pitre
Since vmlinux.lds.S is preprocessed, we can use the defines already
present in asm/memory.h (allowed by patch #3060) for the XIP kernel link
address instead of relying on a duplicated Makefile hardcoded value, and
also get rid of its dependency on awk to handle it at the same time.
While at it let's clean XIP stuff even further and make things clearer
in head.S with a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch allows for assorted type of cleanups by letting assembly code
use the same set of defines for constant values and avoid duplicated
definitions that might not always be in sync, or that might simply be
confusing due to the different names for the same thing.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some boards declare prom_free_prom_memory as a void function but the
caller free_initmem() expects a return value.
Fix those up and return 0 instead, just like everyone else does.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prefetching may be fatal on some systems if we're prefetching beyond the
end of memory on some systems. It's also a seriously bad idea on non
dma-coherent systems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Limit the number of cpu type options in the cpu menu to just those
types that are actually available for the select platform.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE 1.2.5 and earlier fails to turn on the ExpMemEn bit in the
PCIFeatureControl register, which means that DMA does not work
beyond physical address 01_0000_0000, ergo to DRAM beyond 1GB.
With ExpMemEn turned on, 01_0000_0000-0f_ffff_ffff is mapped,
so DMA works for up to 61 GB of DRAM.
Will be fixed in CFE 1.2.6 (yet to be released).
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PCI support code for PLX 7250 PCI-X tunnel on BCM91480B BigSur board.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Kconfig and Makefile changes
- arch/mips/sibyte/bcm1480/
- changes to sibyte common code to support 1480
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update sibyte headers to match Broadcom internal copies:
- comment cleanup and updates
- fix LittleSur part number to match the board silkscreen
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add header files for BCM1480/1280/1455/1255 family of chips, and
update sb1250 headers which are shared by BCM1480 family.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/include/asm-mips/sibyte/bcm1480_int.h b/include/asm-mips/sibyte/bcm1480_int.h
new file mode 100644
Cacheflush(0, 0, 0) was crashing the system. This is because
flush_icache_range(start, end) tries to flushing whole address space
(0 - ~0UL) if both start and end are zero.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert kgdb_cpulock into a raw_spinlock_t.
SPIN_LOCK_UNLOCKED is deprecated and it's replacement DEFINE_SPINLOCK is
not suitable for arrays of spinlocks.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This may have made sense on a paranoid day with pass 1 BCM1250 processors
that were throwing cache error exception left and right for no good
reason. On modern silicion that hardly makes sense and the code had
gotten just an obscurity ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change the N32 debugging ABI to something more sane, and add support
for o32 and n32 debuggers to trace n64 programs.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
tx39_flush_cache_range() does nothing if !cpu_has_dc_aliases. It should
flush d-cache and invalidate i-cache since the TX39(H2) has separate I/D
cache.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
to it in an asm() block, and we're running on a system with 64-bit
registers, it is vitally important that we sign extend it correctly before
returning to C. Otherwise the stray high bits will be preserved into
csum_fold, and on the SB-1 processor, 32-bit arithmetic on a non
sign-extended register will yield surprising results.
This caused incorrect checksums in some UDP packets for NFS root. The
problem was mild when using a 10.0.1.x IP address, but severe when
using 192.168.1.x.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- converted to platform bus
- removed pci dependencies
- removed virt_to_phys/phys_to_virt calls
System now can root off of a disk.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/Documentation/mips/AU1xxx_IDE.README b/Documentation/mips/AU1xxx_IDE.README
new file mode 100644
pfn<<PAGE_SHIFT sometimes extends beyond. The pte is big enough to hold
'long long', but the shift in pfn_pte() needs to do its calculation with
enough bits to hold the result.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
will also avoid smp_call_function from doing stupid things when called
from a CPU that is not yet marked online.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
hasn't been an actual bug, so it's more a change to be 100% compliant
with the requirements of the architecture spec. Similar fix to
mask_mips_irq where there was a slightly less theoretical chance of
getting hit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
this fixes Lasat pci to work with multi-function devices by assigning
the correct values based on pin number (instead of ignoring them).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thiemo Seufer <ths@networkno.de>
called on a another node than the console node, so use the master_nasid
instead and in the unlikely case that one isn't initialized yet, fall
back to get_nasid().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
supporting parity errors only for memory (Pmax/3min/Maxine).
Fixes for resources decoded by the KN04/KN05 MB ASIC. Additional
clean-ups for the ECC handler.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
never initialized been initialized anywhere, just saved to and
restored from signal frames so nonsense anyway. As neat side effect
of being shared between all processors it was also abusable as a
nice covert channel between processes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So for now we just unconditionally set the option - Linux wouldn't
work without a TLB anyway.
Setting MIPS_CPU_4KTLB was missing for Alchemy and Sandcraft, add that
back.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* remove two already unused and commented structures
* added an ULL suffix to several address constants that use bits 35-32
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
tlb-sb1.c. Make tlb-r4k.c and tlb-sb1.c more similiar and more efficient.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
timer tick. Prior to this patch, if IDE IRQ probing occured, then the
TOY_MATCH2 interrupt would be permanently disabled, and no system timer
tick occurs. This patch corrects this situation by correctly registering
the TOY_MATCH2 interrupt so that IDE IRQ probing doesn't have adverse
side effects.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the greatest thing to do. Try to enable parity protection, check if
we actually succeeded and print a message about the outcome of this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
are now working for 80% of the ones I have tried. The other ones that do
not work all fail in the same way with the same messages. Once that bug
is tracked down, we should be in good shape. Task locking still needs
some work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
VA_TO_REG. Who ever wrote this apparently did enjoy the C Puzzle Book.
ISBN 0201604612, a little old but still fun reading for the next
blackout ;)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the 'load_irix_binary' and having kernel faults, Irix support is
disabled. I suspect locking of some sort, but I will now have to
investigate further.
Static IRIX binaries are now being detected properly and are using the
ELF interpreter found in this file.
Signed-off-by: Steven J. Hill <sjhill@realitydiluted.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
binutils are broken and don't warn about this use of $at even though
gas is in .set noat mode so this for now is an accident waiting to
happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The dev_kfree_skb in islpci_eth_transmit happens while irqs are still
disabled, so either dev_kfree_skb_irq needs to be used or the skb
needs to be freed after irqs have been enabled again. This patch
should fix it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This one from my DMA_{32,64}BIT_MASK series did not seem to make it
through to upstream.
Use the DMA_{32,64}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
trivial iomem annotations + missing memcpy_fromio() caught by
those
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
libata-core cleanups:
- use kzalloc() instead of kmalloc() + memset();
- use one exit path in ata_device_add();
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
We want ->tf_read() to get a complete snapshot of all taskfile
registers, without requiring the callers to manually call
ata_chk_status() and ata_chk_err() themselves.
This also fixes a minor bug in sata_vsc where the lower bits of the
feature register were incorrectly placed in the HOB (high order bits)
portion of struct ata_taskfile.
Bluetooth HIDP selects INPUT and it really needs it to be there - module
depends on input core. And input core is never built on s390...
Marked as broken on s390, for now; if somebody has better ideas, feel
free to fix it and remove dependency...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
switched to simple_read_from_buffer(), killed broken use of min().
Incidentally, that use of min() had been fixed once, only to be
reintroduced in commit 4244f72436:
[PATCH] USB: upgrade of the idmouse driver
[snip]
- if (count > IMGSIZE - *ppos)
- count = IMGSIZE - *ppos;
+ count = min ((loff_t)count, IMGSIZE - (*ppos));
Note the lovely use of cast to shut the warning about misuse of min()
up...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
frv, sh64, ia64 and sparc64 do not have do_settimeofday() exported (the
last two are using variant in kernel/time.c). Exports added to match
the rest of architectures.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use of IS_ERR/PTR_ERR in infiniband/core/agent.c, without a portable
chain of includes pulling err.h (breaks on a bunch of platforms).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
exit_signal() (called from copy_process's error path) should decrement
->signal->live, otherwise forking process will miss 'group_dead' in
do_exit().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
as-iosched deals with aliased requests differently from other ioscheds.
It links together aliased requests using rq->queuelist instead of
spilling alises to dispatch queue like other ioscheds do. Requests
linked in this way cannot be merged.
Unfortunately, generic q->last_merge handling patch didn't take this
into account and q->last_merge could be set to an aliased request
resulting in Badness, corrupt list and eventually panic.
This explicitly marks aliased requests to be unmergeable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added kmap_atomic/kunmap_atomic. Added protection of KM_IRQ0 slot with
local_irq_save(), local_irq_restore(), and comments.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Kenneth Tan
Defining IXP46X peripheral devices memory mapping definitions that have
been missed out:
o Peripheral virtual base address is being adjusted to allow more headroom to add extra peripheral device addresses
o Peripheral size is being increased to address the above needs
o Virtual address of expansion bus and PCI configuration register needs to be adjusted as new peripheral device memory space is overlapping with their virtual address space
Signed-off-by: Kenneth Tan <chong.yin.tan@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Return FAILED from eh_ routines if command(s) is(are) not completed
There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adjust lpfc_scsi_buf allocation to account for lun_queue_depth and
error handling
Under high load and high duress, the error handler could steal some
command resources from the normal i/o path. Rework to allocate
additional resources to avoid this scneario.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace lpfc_sli_issue_iocb_wait_high_priority with lpfc_sli_issue_iocb_wait.
Simplify code paths, as there really wasn't a "priority"
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: James Smart <James.Smart@emulex.com>
There were scenarios where the error handlers could reuse an iotag
value of an active io. Remove all possibility of this by
pre-assigning iotag resources to command resources.
Signed-off-by: James Smart <James.Smart@emulex.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Nicolas Pitre
Fix XIP support after recent bootmem code refactoring.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Introduce ixp2000_reg_wrb, which is a variant of ixp2000_reg_write
that does a readback from the target register, to make sure that
the write has been flushed out of the write buffer.
Unlike the previous (ineffective) readback in ixp2000_reg_write, this
readback is followed by an instruction that depends on the value of
the readback so that the CPU actually stalls until the readback has
completed.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The workaround that we do for avoiding triggering ixp2400 erratum #66
involves mapping I/O pages using XCB=101 instead of XCB=000 so that we
prevent the I/O signal to the gasket from being asserted (which can
cause data corruption.) But XCB=101 mappings are write-buffered while
mappings using XCB=000 are not, which is why if we use XCB=101 mappings
we do a readback for every CSR store in an attempt to make sure that
the store has been pushed out of the xscale core and the gasket.
Unfortunately, there are two issues with this:
- we do a readback for every CSR store, which is wrong, because the
register we are writing to might have unwanted side-effects on read,
for example, in the case of the scratchpad ring enqueue/dequeue
registers; and
- the readback is totally ineffective in the way we currently do it,
because we just issue a load but do not issue any instruction that
depends on the return value of that load, so the xscale core does
not wait for the load to complete before continuing.
See this linux-arm-kernel mailing list post for further information:
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2005-September/031314.html
This means that my ixp2400 boxes have been running for many months
without a working readback in ixp2000_reg_write, without any apparent
adverse effects. Two of them have been running for a week now with
the actual readback deleted from ixp2000_reg_write, also without any
apparent ill effects.
So, because in its current form it does more harm than good, the
readback in ixp2000_reg_write should simply be killed, as the patch
below does.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Table was not providing a lot of value and injected a couple of
errors. Removed it and made functionality inline.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix for "Unknown IOCB command Data: x0 x3 x0 x0" messages and
inability to see devices
On some platforms, the host-memory based ring mgmt area was not
zero. Also, driver wasn't manipulating the entire 32bits of the ring
pointers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Unfortunately, some devices forgot to reset the flash on reboot.
Arrange for the map driver to suspend & resume the flash to
ensure that it is in a sane state before rebooting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reuse macros defined for sysfs store callbacks in the initialization
code in order to enforce the same range checking.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This got dropped from the SA1100 flash driver a while back and
never added to the platform support file. Add it back.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup white spaces in argument calls & initializations, prune if
statements, remove casting and remove redundant if checks.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hopefully there should be a brand new replacement driver for this heap
of junk by the beginning of next year.
Acked By: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement reporting asynchronous CQ events in Mellanox HCA driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Macro arguments should _always_ be surrounded by parentheses
when used to prevent unexpected problems with operator precedence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the machine information structures are now static, the
compiler might optimise them away. Mark them with
__attribute_used__ to prevent this occuring.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Somehow we ended up with an #ifdef CONFIG_PPC64 around the export
of cur_cpu_spec, but raid6 as a module needs it on ppc32 as well
as ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently when we first select memory model (FLAT, DISCONTIG, SPARSE) then
select whether the machine is NUMA. However NUMA systems may not be FLAT.
This constraint it not honoured and we may configure a NUMA/FLAT system.
Reorder the configuration such that we choose NUMA first which allows us to
only list the memory models which are valid. We now default NUMA for known
NUMA systems. Note that this new order also matches that used in x86.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove duplicate local variable, saves 2 asm instructions.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'make install' creates a /boot/zImage[.vmode] file when the defconfig is used.
It uses the second arg as file content, which is the vmlinux, and the 5th
arg as file name, which is the BOOTIMAGE name.
A comment in an earlier patch to install.sh states that yaboot can not load
a zImage+initrd combo. This was true in kernel 2.6.5 because it did use
bi_recs to pass the initrd info. But this concept was always broken.
Register r3 holds the initrd address and r4 holds the initrd size. This
works with all kernel versions. The current code in main.c leaves r3 and
r4 alone, so the kernel should be able to see and use the memory range with
the initrd content.
If one wants to rerun mkinitrd, it is currently hard to get the uname -r
value for the installed zImage. Without this info, mkinitrd can not know
what modules to use. This would be fixable by including the /proc/version
output of the new kernel. But it is simpler to just use the plain vmlinux.
So all this patch does is to write to /boot/vmlinux instead to /boot/zImage
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'make ARCH=ppc64 O=../O install' does not work with the defconfig.
CONFIG_PPC_BPA is part of it, but the BPA bootimage variable is wrong:
make[2]: *** No rule to make target `zImage', needed by `install'. Stop.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
compile nls_cp437 and nls_iso8859_1 into the kernel in defconfig. This is
already enabled in pSeries_defconfig.
Reason: if one just boots the new shiny zImage and the root filesystem is
on a filesystem not readable by yaboot (like jfs, raid or lvm) upgrading
the bootloader will fail because the FAT bootpartition can not be mounted.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, AC Power is 0 on a desktop G4. No batteries present should mean
AC Power == 1.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Show firmware provided stackpointer during boot.
This helps to find the "taboo" areas on the various boards. claim tends to
fail for these memory areas, but some jokers return success anyway.
Use %p to print the load address, its a pointer.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To prove that the relocation works, move the crt0.o away from the beginning.
Move linker options from command line into linker script. rename entry point
because '_start' is referenced in printf output.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the zImage relocateable. So yaboot could just load and run any ELF
binary, without worrying about its load address.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove userland related stuff from ld.script, they are not required for zImage
use wildcards for some sections.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compute the vmlinux size at runtime.
Use Z_FULL_FLUSH instead of Z_FINISH, to extract only the ELF header
and ELF program header.
->p_memsz is the required memory range for the executable, including bss
->p_filesz is the size of .text, .data and other runtime sections
These values must be used for the claim call.
All additional memory needed by the kernel is claimed in prom_init, remove
the extra Mb.
Pass the full memsize as target area to gunzip, otherwise not everything
will be uncompressed.
flush_cache has to flush all runtime sections, do not reduce the memrange
by the ->p_offset value because its just that: an offset.
Remove the Makefile code to produce an imagesize.c, its not needed anymore.
Remove all FORCE flags, to not rebuild the zImage if vmlinux was not changed.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Switch ppc64 to the in-kernel zlib, it has less bugs than the current one.
The code in arch/ppc64/boot is compiled as 32bit, so it can not use the
includes from include/asm.
Copy all zlib related header files and convert them with sed.
Reduce the scratch size to 47k, check possible changes at runtime.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fib_del_ifaddr() dereferences ifa->ifa_dev, so the code already assumes that
ifa->ifa_dev is non-NULL, the check is unnecessary.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Added information message when using the SRAM in mv643xx_eth_probe()
Signed-off-by: Nicolas DET <det.nicolas@free.fr>
Signed-off-by: Sven Luther <sl@bplan-gmbh.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a numbers of issues regarding to that both 8xx and 82xx
began to use ppc_sys model:
- Platform is now identified by default deviceless SOC, if no
BOARD_CHIP_NAME is specified in the bard-specific header. For the list
of supported names refer to (arch/ppc/syslib/) mpc8xx_sys.c and
mpc82xx_sys.c for 8xx and 82xx respectively.
- Fixed a bug in identification by name - if the name was not found,
it returned -1 instead of default deviceless ppc_spec.
- fixed devices amount in the 8xx platform system descriptions
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add proper entry to support the Marvell MV64361 (Marvell Discovery II)
SRAM.
This feature may be used by the mv643xx_eth driver.
Signed-off-by: Nicolas DET <det.nicolas@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mesh, mac53c94 and airport already have an entry. Add the network drivers
for pmac.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide a "compatible" entry in /sys/bus/macio/devices/*/ This can be used
to load drivers via the modules.alias file.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a nvram acccess method, similar to
arch/ppc64/kernel/pSeries_nvram.c tested on CHRP B50.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Expose faster ether compare for use by protocols and other
driver. And change name to be more consistent with other ether
address manipulation routines in same file
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The default value for tcp_tso_win_divisor is 3.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Mention a few more commands in xmon. System.map processing was replaced
with kallsyms.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup PPC440 eval boards (bamboo, ebony, luan and ocotea) to better
support U-Boot as bootloader.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is an uptodated version of the MPC8xx PCMCIA driver for v2.6,
addressing comments by Jeff and Dominik:
- use IO accessors instead of direct device memory referencing
- avoid usage of non-standard "uint/uchar" data types
- kill struct typedef's
Will submit it for inclusion once v2.6.14 is out.
Testing on 8xx platforms is more than welcome! Works like a charm
on our custom hardware (CONFIG_PRxK).
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert core 8xx drivers to use in_xxxbe/in_xxx macros instead of direct
memory references.
Other than making IO accesses explicit (which is a plus for readability), a
common set of macros provides a unified place for the volatile flag to
constraint compiler code reordering.
There are several unlucky places at the moment which lack the volatile
flag.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Depending on how GCC is built, GCC 4 may generate altivec instructions without
user explicitly requesting vector operations in the code. Although this is a
performance booster for user applications, it is a problem for kernel.
This patch explicitly instruct GCC to NOT generate altivec instructions while
building the kernel.
Here are some test cases I ran.
(1) build gcc 4.0.1 with '--with-cpu=7450 --enable-altivec
--enable-cxx-flags=-mcpu=7450', and use this gcc to build kernel WITHOUT
this kernel patch. Kernel fail to boot up on a 7450 board because of
altivec instructions in kernel.
(2) build gcc 4.0.1 with "--with-cpu=7450 --enable-altivec
--enable-cxx-flags=-mcpu=7450", and use this gcc to build kernel WITH this
kernel patch. Kernel boot up on a 7450 board without any problem.
(3) build gcc 4.0.1 with "--with-cpu=750 --enable-cxx-flags=-mcpu=750",
and use this gcc to build kernel with or without this kernel patch.
Kernel boot up on a 7450 board without any problem.
This patch should also work with GCC 3 or even earlier GCC 2.95.3.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wrap a highly common idiom. Makes the code easier to read, helps pave
the way for sdev->{id,channel} removal, and adds a token that can easily
by grepped-for in the future.
There are a couple sdev_id() and scmd_printk() updates thrown in as well.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New dev_printk wrappers, which allow us to shrink code, and
eliminate direct references to host/channel/id/lun members:
scmd_printk()
Introduce wrappers for highly common idioms, which may also help us
eliminate some ->{channel,id} references in the future:
{scmd,sdev}_id()
{scmd,sdev}_channel()
The scmd_* wrappers are present in scsi/scsi_device.h because they all
employ the dereference chain cmd->device->$member. We would prefer to
use static inline functions rather than macros, but that would have a
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Various whitespace and comment fixes from Eric, aswell as a version
bump.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Support PHY resets in mptsas. Thanks to Eric for various bug fixes
and improvements.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a flag to mark a PHY as attached to the HBA as opposed to beeing on
an expander. This is needed because various features are only supported
on those. This is a crude hack, the proper fix would be to use
different classes for host-attached vs expander phys. I'm looking into
that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This driver comes from the gnokii project.
Was further cleaned up by me to match recent usb-serial core changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to get the ELV FHZ1000 Home Automation control device to
work with Linux. The patch adds a new device ID to the ftdi_sio driver.
It is for kernel version 2.6.13.4.
Signed-off-by: Martin Hagelin <martin.hagelin@home.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_PM=n:
drivers/built-in.o(.text+0x1098c): In function `hub_thread':
drivers/usb/core/hub.c:2673: undefined reference to `.dpm_runtime_resume'
drivers/built-in.o(.text+0x10998):drivers/usb/core/hub.c:2674: undefined reference to `.dpm_runtime_resume'
Please, never ever ever put extern decls into .c files. Use the darn header
files :(
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_PM=n:
drivers/built-in.o(.text+0x2a69c): In function `ohci_hub_control':
drivers/usb/host/ohci-hub.c:539: undefined reference to `.usb_hcd_resume_root_hub'
drivers/built-in.o(.text+0x2b920): In function `ohci_irq':
drivers/usb/host/ohci-hcd.c:726: undefined reference to `.usb_hcd_resume_root_hub'
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as592) makes a few small improvements to the way device
strings are handled, and it fixes some bugs in a couple of other sysfs
attribute routines. (Look at show_configuration_string() to see what I
mean.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as591) fixes a rather innocuous bug that has been around for
quite a long time: Virtual root hubs should have a maxpacket length of
64 for endpoint 0. I didn't realize it was wrong until I started
looking through the endpoint attribute files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as590) fixes up all the remaining places where usbcore can
use kzalloc rather than kmalloc/memset.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I can't stand text lines that wrap-around in my 80-column windows. This
patch (as589) makes cosmetic changes to a couple of source files.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as588) fixes the way endpoint attribute files are registered
and unregistered. Now they will correctly track along with altsetting
changes. This fixes bugzilla entry #5467.
In a separate but related change, when a usb_reset_configuration call
fails, the device state is not changed to USB_STATE_ADDRESS. In the
first place, failure means that we don't know what the state is, not
that we know the device is unconfigured. In the second place, doing
this can potentially lead to a memory leak, since usbcore might not
realize there still is a current configuration that needs to be
destroyed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as587b) improves the implementation of USB endpoint
sysfs files. Instead of storing a whole bunch of attributes for every
single endpoint, each endpoint now gets its own kobject and they can
share a static list of attributes. The number of extra fields added to
struct usb_host_endpoint has been reduced from 4 to 1.
The bEndpointAddress field is retained even though it is redundant (it
repeats the same information as the attributes' directory name). The
code avoids calling kobject_register, to prevent generating unwanted
hotplug events.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freecom seems to be one of those vendors that can't get the GET CAPACITY
thing right. This expands the US_FL_FIX_CAPACITY flag for the entire
range of their fccd product line.
This is based on a patch sent by Stuart Black
<stuart_black@yahoo.co.uk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is originally from Alan Stern (as569). It has been rediffed
against a current tree.
This patch converts usb-storage to use the kthread API for creating its
control and scanning threads. The new code doesn't use kthread_stop
because the threads need (or will need in the future) to exit
asynchronously.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch from Alan Stern started as as568. It has been rediffed against
a current tree.
This patch adds minimal suspend/resume support to usb-storage. Just enough
for it to qualify as PM-aware.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is from Alan Stern (as560). It has been rediffed against a
current tree.
This patch allocates a separate buffer for usb-storage to use when
auto-sensing. Up to now we have been using the sense buffer embedded in a
scsi_cmnd struct, which is dangerous on hosts that (a) don't do
cache-coherent DMA or (b) have DMA alignment restrictions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is originally from Alan Stern (as557). It has been re-diffed
against a current tree, and I also corrected a minor merging error.
Some time ago we introduced a delay before device scanning, because many
devices do not like to receive SCSI commands right after enumeration.
Now it turns out there's a device that doesn't like to receive
Get-Max-LUN right after enumeration either. Accordingly this patch
delays the Get-Max-LUN request until the beginning of the scanning
procedure. This fixes Bugzilla entry #5010.
Three things are worth noting. First, I removed the locking code from
usb_stor_acquire_resources. It's not needed, because the locking is to
protect against disconnect events and acquire_resources is only called
during probe (so the disconnect routine can't be called). Second, I
initialized to 0 the buffer used for the Get-Max-LUN response. It's not
really necessary, but it will prevent random values from showing up in
the debugging log when the request fails. Third, I added a test against
the SINGLE_LUN flag. This will allow us to use the flag to indicate
Bulk-only devices that can't handle Get-Max-LUN.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as577) adds a Clear-Halt call on the Interrupt-in endpoint
during input device configuration. Without it my HP USB keyboard doesn't
work.
Vojtech says it's worth trying, since it might help with some recalcitrant
devices. On the other hand, it might interfere with others. I'm
submitting it so that it can get tested by a range of users.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter. It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support). And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch improving the set of vendor/product IDs used in the
"ipaq" USB serial device driver. The patch size is because I sorted the
ids this time, forgot about that last time.
Changes:
- Added vendor/product identifiers for Psion Teklogix devices
- Restored Microsoft's identifier pair 045e/00ce
- Sorted list of vendor/product identifiers
Signed-off-by: David Eriksson <twogood@users.sourceforge.net>
Signed-off-by: Ganesh Varadarajan <ganesh@veritas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some arch (like arm) udelay cannot be called with value greater that
2000.
Signed-off-by: Guillaume GOURAT / guillaume.gourat@nexvision.fr
Signed-off-by: Oliver Neukum <oliver@neukum.name>
On Tue, 18 Oct 2005, Simeon Simeonov wrote:
> Attached is a patch that solves mounting problems for
> LEICA D-LUX camera with FC4 2.6.13 kernel.
>
> Let me know if you have some questions.
Looks okay to me. Given that the previous entry uses the full 0000 -
9999 range, I guess this one can also. The vendor name is a little odd
(it will give us three different vendor names all in entries with the
same vendor ID) but that doesn't really matter either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem with some cdc acm devices that were not getting
automatically loaded as the module alias was not being reported
properly.
This check was for back in the days when we only reported hotplug events
for the main usb device, not the interfaces. We should always give the
interface information for MODALIAS/modalias as it can be needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These numbers are pointless, as they have not been changed in _years_,
so we should just remove them to stop pretending there is an actual
"version number" for these drivers.
This should also help reduce confusion when people try to ask for
support of a specific driver version, as there has been no way to tell
what they are talking about.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes up a lot of problems in sysfs with some of the usb serial
drivers, they had incorrect driver names. Also saves a tiny ammount
of memory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm tired of trying to explain why a "device_type" is really a driver.
This better describes exactly what this structure is.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a real Bluetooth system in Linux, lets finally delete this driver as no
one is using it (and if they are, they are using a closed source bluetooth
stack, which I can't support anyway.)
Marcel, you owe me a beer :)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should let us get rid of all of the different hooks in the USB core for
when something has changed.
Also, some other parts of the kernel have wanted to know this kind of
information at times.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as582) adds a missing transfer_flags setting to the usbtest
driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add .owner initialisation to the device drivers
in drivers/usb/host so that when built as module
the device_driver refers to the owning module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure the the device_driver and usb_gadget_driver
have their .owner fields initialised to associate
the module owner to the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialise the .owner field of the driver with
the module that owns it, to aid in linking
drivers to modules.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.
This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.
Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as581) changes the assignments to hcd->state in the uhci-hcd
driver. It fixes part of bugzilla entry #5227. The problem was revealed
by David's large suite of USB suspend/resume patches; this patch should go
to Linus at the same time those do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change to make DMA work two bytes at a time omitted an important
tweak that affects the file_storage gadget: it needs to recognize when
the host writes an odd number of bytes. (The network layer ignores
such extra bytes.)
This patch resolves that issue by checking the relevant bit and adjusting
the rx byte count, so that for example a legal 13 byte request doesn't
morph into an illegal 14 byte one any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb/core/buffer.c doesn't export any symbols, so it should use
!I instead of !E to eliminate this warning message:
Warning(/var/linsrc/linux-2614-rc4//drivers/usb/core/buffer.c): no structured comments found
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just a small patch that fixes a small parameter validation bug.
drivers/usb/input/map_to_7segment.h:
This patch fixes the broken parameter validation in the char to seg7
conversion. This could cause out-of-bounds memory references.
MAINTAINERS:
Yealink maintainer info now in sorted order.
Documentation/input/yealink.txt:
Added a Q&A section that answers some common questions.
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
006491df1a13f85ad245d1039dfdf20e49c394fd
The uhci-hcd driver is fairly lax about the way it handles isochronous
transfers. This patch (as579) improves it in three respects:
TDs for a new URB aren't added to the schedule until all of
them have been allocated. This way there's no risk of the
controller executing some of them when an allocation fails.
TDs for an unlinked URB are removed from the schedule as soon
as the URB is unlinked, rather than waiting until the URB is
given back. This way there's no risk of the controller still
executing a TD after the URB completes.
The urb->error_count values are now reported correctly.
Although since they aren't used in any drivers except for
debug messages in the system log, probably nobody cares.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code. It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume. These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.
It also takes David's advice about removing the layer of bus glue, where
those methods are called. And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as574) updates the PCI BIOS usb-handoff code for UHCI
controllers, making it work like the reset routines in uhci-hcd. This
allows uhci-hcd to drop its own routines in favor of the new ones
(code-sharing).
Once the patch is merged we can turn the usb-handoff option on
permanently, as far as UHCI is concerned. OHCI and EHCI may still have
some issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as575) fixes an unlikely race in the g_file_storage driver.
The problem can occur only when the driver is unbound before its
initialization routine has finished.
I also took the opportunity to replace kmalloc/memset with kzalloc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds US_FL_FIX_CAPACITY for yet _another_ entire block of Apple
productIds. They really can't seem to get this right. This one is for
the iPod Nano. Reported by Tyson Vinson <lornoss@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h | 10 ++++++++++
1 file changed, 10 insertions(+)
This patch adds the US_FL_IGNORE_RESIDUE flag for the TrekStor i.Beat
Joy 2.0. Original version of this patch was sent by Stefan Werner
<dustbln@gmx.de> with test/rediff/etc. by me.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h | 7 +++++++
1 file changed, 7 insertions(+)
A while ago, Matthew Dharm wrote:
> Looks good. Tho, I would like to see a future patch to do two things:
> 1) Change comments from C++ style to C-style
> 2) Make sure we're naming consistently everywhere SCM, USBAT,
> USBAT-02 (most noticably needing fixing is the string used at
> transport-selection time, but a sweep of all uses to be consistent
> would be in order).
Sorry for the long delay, here is a patch to address this. I also clarified
some ATA/ATAPI wording + function names.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/shuttle_usbat.c | 306 ++++++++++++++++++++----------------
drivers/usb/storage/shuttle_usbat.h | 66 +++----
drivers/usb/storage/transport.h | 2
drivers/usb/storage/unusual_devs.h | 10 -
drivers/usb/storage/usb.c | 4
5 files changed, 213 insertions(+), 175 deletions(-)
There appears to be one more case where the HP8200 CD writer devices are
detected as flash readers - when the USB cable is replugged after use, with
the power cable still connected.
Oddly enough, the identify device command appears to 'fall through' when the
devices are in this state, the status register reading exactly the same opcode
as the command (0xA1) that was just executed.
I think it's safe to label this behaviour as specific to HP8200 devices, I
can't get the flash devices to respond like this.
This patch should solve the last of the HP8200 issues which have cropped up
recently.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/shuttle_usbat.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
the following patch splits the NOTE: in the Device Drivers->USB submenu of
Kconfig thus making the whole of it readable on 600x800 terminals.
(Otherwise, the line was too big and disappeared into nowhere.)
Signed-off-by: Borislav Petkov <petkov@uni-muenster.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
This one is a tiny patch adding one more device to the list. Please
apply. :)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/net/pegasus.h | 2 ++
1 file changed, 2 insertions(+)
We would like to add a PID for the Pyramid Appliance Display, which works
on USB via FTDI_SIO.
Signed-off-by: Thomas Riewe <thomasr@pyramid.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/ftdi_sio.c | 1 +
drivers/usb/serial/ftdi_sio.h | 3 +++
2 files changed, 4 insertions(+)
Also has the nice benefit of making sparc alignment issues go away.
Thanks to David Miller for pointing out the problems here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 22 ++++++++++++----------
drivers/usb/core/hub.h | 2 +-
2 files changed, 13 insertions(+), 11 deletions(-)
This patch (as566) converts the File-Storage gadget over to the kthread
API. The new code doesn't use kthread_stop because the control thread
needs to terminate asynchronously when it receives a signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/file_storage.c | 32 +++++++++++++-------------------
1 file changed, 13 insertions(+), 19 deletions(-)
This patch (as570) changes some comments in the uhci-hcd header file and
removes an unused declaration (something I forgot to erase in an earlier
patch).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/uhci-hcd.h | 91 +++++++++++++++++++++++---------------------
1 file changed, 49 insertions(+), 42 deletions(-)
Because there is no bulk_interrupt_message() routine and no
USBDEVFS_INTERRUPT ioctl, people have been forced to abuse the
usb_bulk_message() routine and USBDEVFS_BULK by using them for interrupt
transfers as well as bulk transfers.
This patch (as567) formalizes this practice and adds code to
usb_bulk_message() for detecting when the target is really an interrupt
endpoint. If it is, the routine submits an interrupt URB (using the
default interval) instead of a bulk URB. In theory this should help HCDs
that don't like it when people try to mix transfer types, queuing both
periodic and non-periodic types for the same endpoint.
Not fully tested -- I don't have any programs that use USBDEVFS_BULK for
interrupt transfers -- but it compiles okay and normal bulk messages work
as well as before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/message.c | 24 ++++++++++++++++++++----
1 file changed, 20 insertions(+), 4 deletions(-)
Reject URBs to _all_ devices when their host controllers are suspended;
even root hub registers will be unavailable. Also, don't reject urbs
to root hubs in other cases; the only upstream link is through that
controller (on PCI or whatever SOC bus is in use).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 28 ++++++++++++----------------
drivers/usb/core/urb.c | 3 ++-
2 files changed, 14 insertions(+), 17 deletions(-)
The way we're looking at USB suspend lately doesn't expect drivers to
call usb_suspend_device() or usb_resume_device() directly; that'll
be implicit when no interfaces are in use.
This patch removes those APIs from visibility outside usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
drivers/usb/core/hub.c | 12 ++++--------
drivers/usb/core/usb.h | 4 ++++
include/linux/usb.h | 5 -----
3 files changed, 8 insertions(+), 13 deletions(-)
This makes the isp116x driver stop using usb_suspend_device() and
usb_resume_device() ... usbcore now calls to the root hub methods,
removing the need for this. It also switches from keventd to khubd
for remote wakeup. (Compile tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/isp116x-hcd.c | 29 ++++-------------------------
drivers/usb/host/isp116x.h | 1 -
2 files changed, 4 insertions(+), 26 deletions(-)
The PCI "early usb handoff" quirk logic didn't work like "ohci-hcd" ...
This patch makes it do so by:
- Resetting the controller after kicking BIOS off, matching the
normal "chip in hardware reset" startup mode;
- Reporting any BIOS that borks this simple handoff; it's likely
got a few other surprises for us too.
- Ignoring that handoff on HPPA;
The diagnostic string is mostly shared with EHCI, saving a few bytes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/pci-quirks.c | 22 ++++++++++++++++++----
1 file changed, 18 insertions(+), 4 deletions(-)
This simplifies the OHCI root hub suspend logic:
- Uses new usbcore root hub calls to make autosuspend work again:
* Uses a newish usbcore root hub wakeup mechanism,
making requests to khubd not keventd.
* Uses an even newer sibling suspend hook.
- Expect someone always made usbcore call ohci_hub_suspend() before bus
glue fires; and that ohci_hub_resume() is only called after that bus
glue ran. Previously, only CONFIG_USB_SUSPEND promised those things.
(Includes updates to PCI and OMAP bus glue.)
- Handle a not-noticed-before special case during resume from one of
the swsusp snapshots when using "usb-handoff": the controller isn't
left in RESET state. (A bug to fix in the usb-handoff code...)
Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ohci-dbg.c | 4 ----
drivers/usb/host/ohci-hcd.c | 2 +-
drivers/usb/host/ohci-hub.c | 42 ++++++++++++------------------------------
drivers/usb/host/ohci-mem.c | 1 -
drivers/usb/host/ohci-omap.c | 36 ++++++++++++------------------------
drivers/usb/host/ohci-pci.c | 40 ++++++++--------------------------------
drivers/usb/host/ohci.h | 1 -
7 files changed, 33 insertions(+), 93 deletions(-)
This updates the PCI glue to address the new and simplified usbcore suspend
semantics, where CONFIG_USB_SUSPEND becomes irrelevant to HCDs because
hcd->hub_suspend() will always be called.
- Removes now-unneeded recursion support
- Go back to ignoring faults reported by the wakeup calls; we expect them
to fail sometimes, and that's just fine.
The PCI HCDs will need simple changes to catch up to this, like being able
to ignore the setting of CONFIG_USB_SUSPEND.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd-pci.c | 106 +++++++++++++++++++++------------------------
drivers/usb/core/hcd.h | 6 +-
2 files changed, 53 insertions(+), 59 deletions(-)
This patch associates hub suspend and resume logic (including for root hubs)
with CONFIG_PM -- instead of CONFIG_USB_SUSPEND as before -- thereby unifying
two troublesome versions of suspend logic into just one. It'll be easier to
keep things right from now on.
- Now usbcore _always_ calls hcd->hub_suspend as needed, instead of
only when USB_SUSPEND is enabled:
* Those root hub methods are now called from hub suspend/resume;
no more skipping between layers during device suspend/resume;
* It now handles cases allowed by sysfs or autosuspended root hubs,
by forcing the hub interface to resume too.
- All devices, including virtual root hubs, now get the same treatment
on their resume paths ... including re-activating all their interfaces.
Plus it gets rid of those stub copies of usb_{suspend,resume}_device(), and
updates the Kconfig to match the new definition of USB_SUSPEND: it provides
(a) selective suspend, downstream from hubs; and (b) remote wakeup, upstream
from any device configuration which supports it.
This calls for minor followup patches for most HCDs (and their PCI glue).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/Kconfig | 11 ++-
drivers/usb/core/hub.c | 163 +++++++++++++++++++++++++----------------------
2 files changed, 97 insertions(+), 77 deletions(-)
This patch collects various small updates related to root hubs, to shrink
later patches which build on them.
- For root hub suspend/resume support:
* Make the existing usb_hcd_resume_root_hub() routine respect pmcore
locking, exporting and using the dpm_runtime_resume() method.
* Add a new usb_hcd_suspend_root_hub() to pair with that routine.
(Essential to make OHCI autosuspend behave again...)
* HC_SUSPENDED by itself only refers to the root hub's downstream ports.
So let HCDs see root hub URBs unless the parent device is suspended.
- Remove an assertion we no longer need (and now, also don't want).
- Generic suspend/resume updates to work better with swsusp.
* Ignore the FREEZE vs SUSPEND distinction for hardware; trying to
use it breaks the swsusp snapshots it's supposed to help (sigh).
* On resume, mark devices as resumed right away, but then
do nothing else if the device is marked NOTATTACHED.
These changes shouldn't be very noticable by themselves.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/base/power/runtime.c | 1
drivers/usb/core/hcd.c | 64 ++++++++++++++++++++++++++++++++++++++-----
drivers/usb/core/hcd.h | 1
drivers/usb/core/hub.c | 45 ++++++++++++++++++++++++------
drivers/usb/core/usb.c | 20 +++++++++----
drivers/usb/core/usb.h | 1
6 files changed, 111 insertions(+), 21 deletions(-)
This cleans up a small recent FIXME, ensuring that all the HCDs provide
root hub suspend/resume methods. It also wraps the calls to those root
suspend routines just like on the PCI "USB_SUSPEND not defined" cases,
so non-PCI bus glue won't be as tempted to behave very differently.
Several of the SOC based OHCI drivers forgot to list those methods;
the patch also adds those missing declarations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 42 +++++++++++++++++++++++++---------------
drivers/usb/host/ohci-au1xxx.c | 5 ++++
drivers/usb/host/ohci-lh7a404.c | 5 ++++
drivers/usb/host/ohci-pxa27x.c | 1
drivers/usb/host/ohci-s3c2410.c | 1
drivers/usb/host/ohci-sa1111.c | 1
6 files changed, 40 insertions(+), 15 deletions(-)
This splits BIOS and PCI specific support out of ehci-hcd.c into
ehci-pci.c. It follows the model already used in the OHCI driver
so support for non-PCI EHCI controllers can be more easily added.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ehci-hcd.c | 543 ++++++--------------------------------------
drivers/usb/host/ehci-pci.c | 414 +++++++++++++++++++++++++++++++++
drivers/usb/host/ehci.h | 1
3 files changed, 492 insertions(+), 466 deletions(-)
This saves a word from "struct device" ... there's a refcounting mechanism
stub that's rather ineffective (the values are never even tested!), which
can safely be deleted. With this patch it uses normal device refcounting,
so any potential users of the pm_parent mechanism will be more correct.
(That mechanism is actually unusable for now though; it does nothing.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/base/power/main.c | 26 +++-----------------------
include/linux/pm.h | 1 -
2 files changed, 3 insertions(+), 24 deletions(-)
This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces. This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages. It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL. In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen. Hence there's no longer any need to check for partial
initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM. Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 2 ++
drivers/usb/host/ohci-hcd.c | 2 +-
drivers/usb/host/ohci-hub.c | 4 ++--
drivers/usb/host/ohci-omap.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
drivers/usb/host/ohci-ppc-soc.c | 4 ++--
drivers/usb/host/ohci-pxa27x.c | 2 +-
drivers/usb/host/ohci-s3c2410.c | 3 +--
drivers/usb/host/ohci-sa1111.c | 2 +-
9 files changed, 12 insertions(+), 11 deletions(-)
This gets rid of some inconsistently duplicated logic to resume interfaces.
Similar code was in both finish_port_resume() and in usb_generic_resume().
Now there is just one copy of that code, accessed regardless of whether
CONFIG_USB_SUSPEND is enabled. Fault handling is also more consistent.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 34 +++++++++++++++++++++-------------
drivers/usb/core/usb.c | 23 +++++++++++++++++++++--
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/isp116x-hcd.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
include/linux/usb.h | 2 +-
6 files changed, 46 insertions(+), 19 deletions(-)
This patch removes some recursion in the CONFIG_USB_SUSPEND logic, which
suspended children (of devices or hubs) that weren't already suspended.
When it sees such cases, suspend now just fails cleanly.
That logic was not needed during system-wide sleep state transitions; and
given the current notions of how to manage selective suspend transitions,
we don't want it there either. Where it was particularly handy was coping
with various limitations of the sysfs "echo -n N > power/state" support.
(These include assuming that "N" is always meaningful to the driver; and
that drivers can only transition to state N from state zero.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the handling of power state for USB interfaces.
- Formalizes an existing invariant: interface "power state" is a boolean:
ON when I/O is allowed, and FREEZE otherwise. It does so by defining
some inlined helpers, then using them.
- Adds a useful invariant: the only interfaces marked active are those
bound to non-suspended drivers. Later patches build on this invariant.
- Simplifies the interface driver API (and removes some error paths) by
removing the requirement that they record power state changes during
suspend and resume callbacks. Now usbcore does that.
A few drivers were simplified to address that last change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 33 +++++++++------------
drivers/usb/core/message.c | 1
drivers/usb/core/usb.c | 65 +++++++++++++++++++++++++++++++++----------
drivers/usb/core/usb.h | 18 +++++++++++
drivers/usb/input/hid-core.c | 2 -
drivers/usb/misc/usbtest.c | 10 ------
drivers/usb/net/pegasus.c | 2 -
drivers/usb/net/usbnet.c | 2 -
8 files changed, 85 insertions(+), 48 deletions(-)
This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory. Follow-on patches will need to:
(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and
(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/Makefile | 2
drivers/pci/quirks.c | 253 ---------------------------------------
drivers/usb/Makefile | 1
drivers/usb/host/Makefile | 5
drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++
5 files changed, 280 insertions(+), 253 deletions(-)
When building on a 64-bit platform, gcc produces a warning
"cast of a pointer to an integer of a different size".
The scatterlist.offset on the LHS is unsigned int, so I used
that originally.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/block/ub.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
This patch adds endpoint information for both devices and interfaces to
sysfs. Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/sysfs.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++-
include/linux/usb.h | 4
2 files changed, 197 insertions(+), 2 deletions(-)
This patch enables direct kernel support for the Artemis
and ATIK astronomical based USB CCD cameras.
Since all communications with this camera are done via an
FTDI 245BM chip, it was only needed to specify the
ProductID and VendorID of all three devices.
In what tests are concerned, data was transfered from and
to the FTDI at the chips Top speed (360KB/s).
Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/ftdi_sio.c | 3 +++
drivers/usb/serial/ftdi_sio.h | 13 +++++++++++++
2 files changed, 16 insertions(+)
This tweaks the EHCI reboot notifier to also halt the EHCI controller, and
makes that halt code force IRQs off. Both should always have been done.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ehci-hcd.c | 8 ++++++++
1 file changed, 8 insertions(+)
drivers/net/e1000/e1000_main.c:3645: warning: `e1000_suspend' defined
but not used
Signed-off-by: Ashutosh Naik <ashutosh_naik@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The latest kernel added a pretty ugly fix for the orinoco etherleak bug
which contains bogus skb->len checks already done by the caller and causes
copies of all odd sized frames (which are quite common)
While the skb->len check should be ripped out the other fix is harder to do
properly so I'm proposing for this the -mm tree only until next 2.6.x so
that it gets tested.
Instead of copying buffers around blindly this code implements a padding
aware version of the hermes buffer writing function which does padding as
the buffer is loaded and thus more cleanly and without bogus 1.5K copies.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix suspend/resume on b44 by freeing/reacquiring irq. Otherwise it hangs
on resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e1000_suspend is only used under #ifdef CONFIG_PM. Move the declaration of
it to be the same way, just like e1000_resume, otherwise gcc whines on
compile. I offer as evidence:
static struct pci_driver e1000_driver = {
.name = e1000_driver_name,
.id_table = e1000_pci_tbl,
.probe = e1000_probe,
.remove = __devexit_p(e1000_remove),
/* Power Managment Hooks */
#ifdef CONFIG_PM
.suspend = e1000_suspend,
.resume = e1000_resume
#endif
};
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes an issue reported in drivers/scsi/sr.c by Coverity
Error reported: Pointer returned from "scsi_cd" is never used
Patch description:
Remove the scsi_cd() call as it does not have any effect.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch attempts to fix an issue found in drivers/scsi/scsi_ioctl.c by Coverity.
Error reported:
CID: 3437
Checker: FORWARD_NULL (help)
File: /export2/p4-coverity/mc2/linux26/drivers/scsi/scsi_ioctl.c
Function: scsi_ioctl_send_command
Description: Variable "buf" tracked as NULL was passed to a function that dereferences it.
Patch description:
buf can be NULL if inlen and outlen are both 0. This patch adds check if the
length is non-zero before calling copy from/to user.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move ib_uverbs module to using cdev_alloc() and class_device_create()
so that we can handle device lifetime properly. Now we can make sure
we keep all of our data structures around until the last way to reach
them is gone.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move ib_umad module to using cdev_alloc() and class_device_create() so
that we can handle device lifetime properly. Now we can make sure we
keep all of our data structures around until the last way to reach
them is gone.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a fix for a bug I see on my Toshiba laptop, where the ohci1394
controller gets initialized improperly. The patch adds two PCI fixups
to arch/i386/pci/fixup.c, one that happens early on to cache the value
of the PCI_CACHE_LINE_SIZE config register, and another that later
restores the value, along with a valid IRQ number and some BAR values.
I've tested it on my laptop, and it prevents me from running into what I
consider to be a major bug: IRQ 11 is disabled by the IRQ debug code,
causing my wireless to break.
Thanks to Rob for the original patch to ohci1394.c and Stefan for lots
of proofreading (and a last minute bug caught in review!) and additional
information collection. I think the DMI system list is correct, but we
may need to add some more PCI IDs to the PCI_FIXUP macros over time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: add descriptions for missing function parameters.
Eliminate all kernel-doc warnings here.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI hotplug.c: does not contain kernel-doc, so don't process it for now.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocate resources for adapters with bridges on them.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert megaraid to use pci_driver's shutdown method rather than
the generic device_driver shutdown method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a warning to pci driver registration code so that we know
whether we have drivers using the obsolete driver shutdown
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I told you that the pci_ids.h cleanup was a bad idea ;)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At unload time, the shpchp driver does not remove sysfs files
it had created in the driver's probe entry point. This patch
fixes this problem.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of debug messages generated if shpchp debug is
enabled. I tried to restrict this to removing debug messages that
are either early-driver-debug type messages, or print information
that can be inferred through other debug prints.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove un-necessary header includes, remove dead code, remove
some type casts, receive function return in the correct data
type...
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
State information is currently stored in per-slot as well as
per-pci-function data structures in shpchp. There's a lot of
overlap in the information kept, and some of it is never used.
This patch consolidates the state information to per-slot and
eliminates unused data structures. The biggest change is to
eliminate the pci_func structure and the code around managing
its lists.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch eliminates saving the PCI config header for devices
in hotplug capable slots. We now use the PCI core to get the
specific parts of the config header as required.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The shpc driver registers its probe function for all pci-pci
bridges in the system. Not all of them will be shpc capable, so
look for this capability early in the probe function and return
if there's no work to do on this bridge. The old shpc driver
did some initialization work on all bridges before detecting
that shpc is not supported and unwinds the work it's already done
in that case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the SHPC hotplug driver's dependence on ACPI. We don't
walk the acpi namespace anymore to build a list of bridges and
devices. The remaining interaction with ACPI is to run the
_OSHP method to transition control of hotplug hardware from
system BIOS to the shpc hotplug driver, and to run the _HPP
method to get hotplug device parameters like cache line size,
latency timer and SERR/PERR enable from BIOS.
Note that one of the side effects of this patch is that shpchp
does not enable the hot-added device or its DMA bus mastering
automatically now. It expects the device driver to do that.
This may break some drivers and we will have to fix them as
they are reported.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Info about resources assigned to PCI devices is already available
through sysfs and pci utilities. There's no need for shpchp to
create another sysfs file to display the same information.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the standard hotplug controller driver to use
the PCI core for resource management. This eliminates a whole lot
of duplicated code, and integrates shpchp in the system's normal
PCI handling code.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One more SMBus unhiding quirk, this time for the HP D530. Requested and
successfully tested by Ben Cranston.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a minor patch to the ppc64 PCI hotplug code; it makes the call to
rpaphp_unconfig_pci_adapter() symmetric with respect to the call to
rpaphp_config_pci_adapter(). I discussed this with John Rose, who
had provided the last round of changes for these functions; he
appearently had this patch but somehow failed to mail it out.
Tested. (added/removed device).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
drivers/pci/hotplug/rpaphp.h | 3 ++-
drivers/pci/hotplug/rpaphp_core.c | 5 ++++-
drivers/pci/hotplug/rpaphp_pci.c | 11 +++--------
3 files changed, 9 insertions(+), 10 deletions(-)
pci_ids.h cleanup: remove duplicated entries and change some defines to
explicit value rather than in terms of another constant, preparation for
removing unused symbols
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/pci_ids.h | 28 +++++++++-------------------
1 file changed, 9 insertions(+), 19 deletions(-)
This patch unhides hidden SMBus on ICH6 chipset installed in
Asus M6V notebook. I would like to thank Michal Mleczko for
testing and help.
Signed-Off-By: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/quirks.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpqphp relies on it.
This fixes a problem reported by Bruno Redondi. He reported a flood
of ACPI interrupts, that caused kacpid to run 100% of the time:
http://bugzilla.kernel.org/show_bug.cgi?id=5312
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpqphp_core.c | 24 +++++++++++++++++++-----
1 file changed, 19 insertions(+), 5 deletions(-)
Add pci_{enable,disable}_device() calls. Without pci_enable_device(),
dev->irq is garbage, and cpcihp_zt5550 relies on it.
Compiled but untested, since I don't have the hardware.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Scott Murray <scottm@somanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/hotplug/cpcihp_zt5550.c | 25 +++++++++++++++++++++----
1 file changed, 21 insertions(+), 4 deletions(-)
Cleanup the need_restore switch statement in
pci_set_power_state(). This makes it more safe by explicitly handling
all the PCI power states instead of handling them as the default
case. It also reads a little better IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IPR scsi adapter have an exposure today in that they issue BIST to the adapter
to reset the card. If, during the time it takes to complete BIST, userspace
attempts to access PCI config space, the host bus bridge will master abort the
access since the ipr adapter does not respond on the PCI bus for a brief
period of time when running BIST. On PPC64 hardware, this master abort
results in the host PCI bridge isolating that PCI device from the rest of the
system, making the device unusable until Linux is rebooted. This patch makes
use of some newly added PCI layer APIs that allow for protection from
userspace accessing config space of a device in scenarios such as this.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/scsi/ipr.c | 2 ++
1 file changed, 2 insertions(+)
Some PCI adapters (eg. ipr scsi adapters) have an exposure today in that they
issue BIST to the adapter to reset the card. If, during the time it takes to
complete BIST, userspace attempts to access PCI config space, the host bus
bridge will master abort the access since the ipr adapter does not respond on
the PCI bus for a brief period of time when running BIST. On PPC64 hardware,
this master abort results in the host PCI bridge isolating that PCI device
from the rest of the system, making the device unusable until Linux is
rebooted. This patch is an attempt to close that exposure by introducing some
blocking code in the PCI code. When blocked, writes will be humored and reads
will return the cached value. Ben Herrenschmidt has also mentioned that he
plans to use this in PPC power management.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/access.c | 89 ++++++++++++++++++++++++++++++++++++++++++++++++
drivers/pci/pci-sysfs.c | 20 +++++-----
drivers/pci/pci.h | 7 +++
drivers/pci/proc.c | 28 +++++++--------
drivers/pci/syscall.c | 14 +++----
include/linux/pci.h | 7 +++
6 files changed, 134 insertions(+), 31 deletions(-)
This patch just adds ACPI and GPIO regions to its LPC bridge, similar
way as ICH4 did. I would like to thank Michal Mleczko for testing.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/pci/quirks.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
Change the way IPoIB handles RX packets when it can't allocate a new
receive skbuff. If the allocation of a new receive skb fails, we now
drop the packet we just received and repost the original receive skb.
This means that the receive ring always stays full and we don't have
to monkey around with trying to schedule a refill task for later.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
.. and the fusion part. I had to move around the debug functions around
a little bit so they are below the transport class methods.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename SCTP specific control message flags to use SCTP_ prefix rather than
MSG_ prefix as per the latest sctp sockets API draft.
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
I'm using this card in a RAID1 with 2 new SATA drives with no problems.
Card - SATA 300 TX2plus PDC40775 (3d73)
Signed-off-by: Ed Kear <ed@kear.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SMSC LPC47M997 Super-I/O chip seems to be compatible with the
LPC47M192, so it is supported by the smsc47m1 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the I2C addresses for the ADM1032 and ADT7461 chips.
Also update the links to the Analog Devices web site.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PEC support to the lm90 driver. Only the ADM1032 chip supports it,
and in a rather tricky way, which is why this patch comes with
documentation reinforcements. At least, this demonstrates that the new
PEC support logic in i2c-core can properly deal with chips with partial
PEC support.
As enabling PEC causes a significant performance drop, it can be
disabled through a sysfs file (unsurprisingly named "pec").
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Preparatory patch to add PEC support to the lm90 driver. We need a
centralized function to read register values, where the PEC code will
be later inserted. A positive side effect is that read errors are now
handled properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tests leading to the use of hardware PEC in the i2c-i801 driver
can be simplified.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new SMBus PEC implementation doesn't support PEC emulation on
non-PEC non-I2C SMBus masters, so we can drop all related code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is my rewrite of the SMBus PEC support. The original
implementation was known to have bugs (credits go to Hideki Iwamoto
for reporting many of them recently), and was incomplete due to a
conceptual limitation.
The rewrite affects only software PEC. Hardware PEC needs very little
code and is mostly untouched.
Technically, both implementations differ in that the original one
was emulating PEC in software by modifying the contents of an
i2c_smbus_data union (changing the transaction to a different type),
while the new one works one level lower, on i2c_msg structures (working
on message contents). Due to the definition of the i2c_smbus_data union,
not all SMBus transactions could be handled (at least not without
changing the definition of this union, which would break user-space
compatibility), and those which could had to be implemented
individually. At the opposite, adding PEC to an i2c_msg structure
can be done on any SMBus transaction with common code.
Advantages of the new implementation:
* It's about twice as small (from ~136 lines before to ~70 now, only
counting i2c-core, including blank and comment lines). The memory
used by i2c-core is down by ~640 bytes (~3.5%).
* Easier to validate, less tricky code. The code being common to all
transactions by design, the risk that a bug can stay uncovered is
lower.
* All SMBus transactions have PEC support in I2C emulation mode
(providing the non-PEC transaction is also implemented). Transactions
which have no emulation code right now will get PEC support for free
when they finally get implemented.
* Allows for code simplifications in header files and bus drivers
(patch follows).
Drawbacks (I guess there had to be at least one):
* PEC emulation for non-PEC capable non-I2C SMBus masters was dropped.
It was based on SMBus tricks and doesn't quite fit in the new design.
I don't think it's really a problem, as the benefit was certainly
not worth the additional complexity, but it's only fair that I at
least mention it.
Lastly, let's note that the new implementation does slightly affect
compatibility (both in kernel and user-space), but doesn't actually
break it. Some defines will be dropped, but the code can always be
changed in a way that will work with both the old and the new
implementations. It shouldn't be a problem as there doesn't seem to be
many users of SMBus PEC to date anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Discard I2C_FUNC_SMBUS_*_PEC defines. i2c clients are not supposed to
check for PEC support of i2c bus drivers on individual SMBus
transactions, and i2c bus drivers are not supposed to advertise them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the documented list of devices supported by the i2c-i810
driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop unused i2c-over-parallel-port i2c IDs:
* I2C_HW_B_LPC was never actually used as far as I could search.
* I2C_HW_B_ELV and I2C_HW_B_VELLE are no more used since the
introduction of the unified i2c-parport driver in Linux 2.6.2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix functions declared static and then implemented
without the static in drivers/i2c/chips.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixup functions that have been declared static
and then actually defined without the static on.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lm78.c and lm85.c have a number of items declared static
then implemented without the static on them. The following
patch fixes these sparse errors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eeprom_detect is first declared static and then when
the function is actually implemented, there is no static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the i2c documentation: kzalloc should be used instead of
kmalloc.
I also fixed a couple other things nearby in writing-clients, as several
past changes had never been reported there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc in the S4882 SMBus multiplexing driver.
I guess it's safer that way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop useless casts on kzalloc returned values, as suggested by
Jiri Slaby.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all remaining i2c bus and
chip drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all hardware monitoring
drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memzero in the ixp2000 and ixp4xx
I2C bus drivers.
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The atxp1 and ds1621 drivers should make sure they do not probe
non-hwmon i2c adapters.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new ID to the SMSC LPC47B397-NC hardware
monitoring driver - for a chip that is claimed to be 100%
compatible otherwise.
Signed-off-by: Bryan Young (Utilitek Systems, Inc.)
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In function i2c_isa_add_driver, copied driver should inherit the owner
field as well as the name field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the .owner field for the i2c core struct xxxx_driver
variables.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the .owner field for various struct xxxx_driver
variables which are available on PPC_MAC arch.
This one was _not_ even compile-tested...
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the .owner field for various struct xxxx_driver variables,
other than pci_driver.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates .owner field for various struct pci_driver variables.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanups to the i2c-elektor driver:
* Set the i2c_adapter name field to "i2c-elektor" and use this string
in all resource requests and printks.
* Change space-padding for tab indentation, kill trailing white space,
remove space before comma.
* Use dev_info, pr_info and pr_debug instead of printk.
* Lines chopped to 80 columns.
Signed-off-by: Stig Telfer <stig@lizardlogic.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the i2c-elektor driver, enabling it to compile
cleanly, load and run. The key change is that it uses the new
__iomem/iowrite8/ioread8 functions to abstract the direct or
memory-mapped variants of register access. Also, the original driver
would crash on module load on the Alpha because the PCI memory region
was not remapped into kernel memory.
I have managed the following testing:
* compiled and tested it on my Alpha UP2000+ system.
* compiles cleanly for x86 but I don't have the hardware to test.
Signed-off-by: Stig Telfer <stig@lizardlogic.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DF_NOTIFY is an i2c_driver flag, using it as an i2c_client flag
doesn't make any sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a bit confusing to name a variable the same as an unrelated
structure. The compiler doesn't complain, but it certainly makes the
code harder to understand, and could confuse grep and LXR among
others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more per-i2c-algorithm adapter max. Last time there were
was in July 1999.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop a useless initialization step in the w83627hf driver. The comment
says that the W83627HF PWM2 can be disabled, but it can't. I suppose
this is a leftover from the w83781d driver (from which the w83627hf
driver is derived), as for example the W83782D had the ability to
disable PWM2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete 2 out-of-date, colliding ioctl defines. I2C_UDELAY and
I2C_MDELAY are supposed to be used by i2c-algo-bit, but actually
aren't (and I suspect never were). Moreover, their values are the same
as I2C_FUNCS and I2C_SLAVE_FORCE, respectively, which *are* widely
used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a misplaced comment in i2c.h. Spotted by Hideki Iwamoto.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c documentation fixes.
>From Hideki Iwamoto:
* i2c_smbus_read_i2c_block_data is not deleted in 2.6.10. It still
exists.
* The name which can be set to i2c_driver is up to 31 characters.
>From Jean Delvare:
* Reword the paragraph about i2c_driver.name, to reflect the "new"
naming policy.
* Delete the out-of-date note about now gone inc_use and dec_use
fields.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No more need to check for PEC support being available now that both
the i2c-core and the i2c-i801 drivers are part of the Linux kernel
source tree. It's just there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes w83627hf and w83627ehf drivers to reserve only ports
0x295-0x296, instead of full 0x290-0x297 range. While some other
sensors chips respond to all addresses in 0x290-0x297 range, Winbond
chips respond to 0x295-0x296 only (this behavior is implied by
documentation, and matches behavior observed on real systems). This is
not problem alone, as no BIOS was found to put something at these unused
addresses, and sensors chip itself provides nothing there as well.
But in addition to only respond to these two addresses, also BIOS
vendors report in their ACPI-PnP structures that there is some resource
at I/O address 0x295 of length 2. And when later this hwmon driver
attempts to request region with base 0x290/length 8, it fails as one
request_region cannot span more than one device.
Due to this we have to ask only for region this hardware really
occupies, otherwise driver cannot be loaded on systems with ACPI-PnP
enabled.
Signed-off-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CVS revision IDs are totally useless and irrelevant by now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup the ioctl debug message in i2c-dev. In particular, the minor
number is redundant now that the minor number and the adapter number
are kept in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ixp4xx and ixp2000 i2c bus drivers omit to fill the required
i2c_adapter name field. Copy the device driver name field there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not nice to put #ifdef in the middle of functions.
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
Improve the register dump used to debug the i2c-viapro driver. The
original dump was missing the HSTSTS register and the block data
buffer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 38 ++++++++++++++++++++++++++++++--------
1 file changed, 30 insertions(+), 8 deletions(-)
By slightly shifting the interface between vt596_access and
vt596_transaction, we can save two I/O accesses per SMBus transaction.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
Make it clearer which chips are supported by the i2c-viapro driver,
and which support I2C block transactions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++++++------
drivers/i2c/busses/i2c-viapro.c | 22 +++++++++++++---------
2 files changed, 19 insertions(+), 15 deletions(-)
Cleanups to the i2c-viapro driver:
* Kill unused defines.
* Kill interrupt-related code, as the driver doesn't use interrupts.
* Fix broken comments (some copied from i2c-piix4.)
* Centralize the unsupported command error case in vt596_access.
That way we'll catch all unsupported commands, not only
I2C_SMBUS_PROC_CALL.
* Refactor some code.
* Convert some dev_dbg into dev_err. Errors better be reported even in
non-debug mode.
* Do not verify that the final reset succeeded. It'll be checked at
the beginning of the next transaction anyway.
* Use the driver name to reserve the I/O region.
* Do not print the contents of the SMBREV register, it reads 0 on all
chips I've seen so far.
* Some other minor fixes all over the place.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-viapro.c | 122 +++++++++++++---------------------------
1 file changed, 41 insertions(+), 81 deletions(-)
Implement the I2C block transactions on VIA chips which support them:
VT82C686B, VT8233, VT8233A, VT8235 and VT8237R. This speeds up EEPROM
accesses by a factor 10 or so.
I would like to thank Antonino A. Daplas, Hinko Kocevar, Salah Coronya
and Andreas Henriksson for their help in testing this new feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 7 +++++-
drivers/i2c/busses/i2c-viapro.c | 39 +++++++++++++++++++++++++++++++++---
2 files changed, 42 insertions(+), 4 deletions(-)
Before I go on cleaning up and improving the i2c-viapro driver, let's
fix all the coding style issues: mostly trailing white space, and
spaces used where tabs should be.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/i2c/busses/i2c-viapro | 12 ++---
drivers/i2c/busses/i2c-viapro.c | 76 ++++++++++++++++++------------------
2 files changed, 43 insertions(+), 45 deletions(-)
I am taking over the maintenance of the i2c-viapro SMBus driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MAINTAINERS | 6 ++++++
1 file changed, 6 insertions(+)
The i2c_smbus_data union block member has a comment stating that an
extra byte is required for SMBus Block Process Call transactions. This
has been true for three weeks around June 2002, but no more since, so
it is about time that we drop this comment and fix the definition.
From: Hideki Iwamoto <h-iwamoto@kit.hi-ho.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
include/linux/i2c.h | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Move the check for SMBUS_QUICK in i2c_probe() after the forced
addresses have been handled. This makes it possible for a driver to
leave the probed address lists empty, only providing forced addresses,
and get i2c_probe to work even if the bus doesn't support SMBUS_QUICK.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/i2c-core.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
Using s8 instead of u8 to store temperature register values saves a
few instructions on sysfs file read. The very same was done for
several other drivers a while ago (lm63, lm83, lm90...)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
Convert the w83l785ts driver to use dynamic sysfs callbacks. This is a
small driver so the benefit is thin, but still worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/w83l785ts.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
Clean up name string usage in 12 i2c bus drivers:
* Use the i2c_adapter name for requesting the I/O region rather than
redefining a new string.
* Do not initialize the i2c_adapter name to "unset".
This should save a few data bytes here and there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/i2c/busses/i2c-ali1535.c | 6 +++---
drivers/i2c/busses/i2c-ali1563.c | 6 ++++--
drivers/i2c/busses/i2c-ali15x3.c | 5 +++--
drivers/i2c/busses/i2c-amd756.c | 5 ++---
drivers/i2c/busses/i2c-amd8111.c | 4 +++-
drivers/i2c/busses/i2c-i801.c | 4 ++--
drivers/i2c/busses/i2c-nforce2.c | 4 ++--
drivers/i2c/busses/i2c-piix4.c | 4 ++--
drivers/i2c/busses/i2c-sis5595.c | 5 +++--
drivers/i2c/busses/i2c-sis630.c | 6 ++++--
drivers/i2c/busses/i2c-sis96x.c | 5 +++--
drivers/i2c/busses/i2c-via.c | 4 ++--
12 files changed, 33 insertions(+), 25 deletions(-)
Discard a common out-of-date comment in 5 hardware monitoring drivers.
The hardware monitoring chip drivers are no more setting sensor limits
at initialization time, for quite some time already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/hwmon/lm78.c | 1 -
drivers/hwmon/via686a.c | 1 -
drivers/hwmon/w83627hf.c | 1 -
drivers/hwmon/w83781d.c | 1 -
drivers/hwmon/w83792d.c | 1 -
5 files changed, 5 deletions(-)
hwmon: adm9240 update 2/2: convert to use dynamic sysfs accessors
This patch converts adm9240 to use Yani Ioannou's dynamic sysfs callbacks,
reducing driver memory footprint from 16312 to 14104 bytes on 2.6.14-rc1,
removing the old driver macro mess.
Run tested on Intel SE440BX-2 mobo.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: adm9240 update 1/2: cleanups:
o remove i2c read/write wrapper interface as it does nothing,
o change kmalloc + memset to kzalloc
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, 'make distclean' causes stgit to barf since it may delete
files in .git/patches. We really shouldn't allow 'make distclean'
anywhere near .git...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ipw2200 driver code in current GIT contains a kmalloc() followed by
a memset() without handling a possible memory allocation failure.
Signed-off-by: Panagiotis Issaris <panagiotis.issaris@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) Forgotten counter incrementation in sis900_rx() in case
it doesn't get memory for skb, that leads to whole interface failure.
Problem is accompanied with messages:
eth0: Memory squeeze,deferring packet.
eth0: NULL pointer encountered in Rx ring, skipping
2) If counter cur_rx overflows and there'll be temporary memory problems
buffer can't be recreated later, when memory IS available.
3) Limit the work in handler to prevent the endless packets processing
if new packets are generated faster then handled.
Signed-off-by: Konstantin Khorenko <khorenko@sw.ru>
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Under heavy PCI bus load, ports of the DFE-580TX 4-ethernet port board stop
working, with currently no other cure than a powercycle. Here is a tested
fix. By the way, I also fixed some references and attribution.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IXDP2x01 systems can be built without PCI network cards, so we should not
require NET_PCI to build CS89x0 on these systems.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If the interface is not used right away after being probed it wastes
power needlessly. Noted by Holger Schurig.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a patch that changes the way the MAC filter is computed for the
multicast addresses. The computation is taken from the SiS GPL driver.
This patch is necessary to get IPv6 working.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Looks like someone used the MII constants instead of the ethtool constants.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The documentation about s2io is available at
Documentation/networking/s2io.txt.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
prism54 is leaking information when passing transmits to the firmware.
There is no requirement to adjust the length to >= ETH_ZLEN.
Just pass the skb length (after possible adjustment).
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some older DL10019 based cards need to setup
the auto-negotiation-advertisement register
to advertise 100Full,100Half,10Full and 10Half.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes a bug that happens when the hypervisor can't add a
buffer. The old code wrote IBM_VETH_INVALID_MAP into the free_map
array, so next time the index was used, a ibmveth_assert() caught it and
called BUG(). The patch writes the right value into the free_map array
so that the index can be reused.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds the lockless TX feature to the ibmveth driver. The
hypervisor has its own locking so the only change that is necessary is
to protect the statistics counters.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes the allocation of RX skb's buffers from a workqueue
to be called directly at RX processing time. This change was suggested
by Dave Miller when the driver was starving the RX buffers and
deadlocking under heavy traffic:
> Allocating RX SKBs via tasklet is, IMHO, the worst way to
> do it. It is no surprise that there are starvation cases.
>
> If tasklets or work queues get delayed in any way, you lose,
> and it's very easy for a card to catch up with the driver RX'ing
> packets very fast, no matter how aggressive you make the
> replenishing. By the time you detect that you need to be
> "more aggressive" it is already too late.
> The only pseudo-reliable way is to allocate at RX processing time.
>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch changes the way the ibmveth driver handles the receive
buffers. The old code mallocs and maps all the buffers in the pools
regardless of MTU size and it also limits the number of buffer pools to
three. This patch makes the driver malloc and map the buffers necessary
to support the current MTU. It also changes the hardcoded names of the
buffer pool number, size, and elements to arrays to make it easier to
change (with the hope of making them runtime parameters in the future).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch updates dev->trans_start and dev->last_rx so that the ibmveth
driver can be used with the ARP monitor in the bonding driver.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update version and reldate and add more sanity checking to
tg3_set_settings().
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.
tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- move default mode pages to the front of libata-scsi.c
so various functions can access them
- partial annotation of these pages, point out divergence
from sat-r06
- replace various mode page magic numbers with defines
- strengthen MODE SENSE command decoding: handle DBD
bit in cdb, yield block descriptor (per sat-r06) and
handle mode sub pages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For now supporting the ->get_linkerrors method is mandatory. I'll
probably be beaten to implement the .show_foo variables and different
types of attributes soon..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move the remaining bits of sgiwd93.h into sgiwd93.c; replace the use of
CMD_PER_LUN and CAN_QUEUE by raw numbers.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maciej W. Rozycki <macro@linux-mips.org>
Date: Mon Jun 13 19:55:42 2005 +0000
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The file is missing an include of scsi_transport_fc.h
drivers/scsi/qla2xxx/qla_rscn.c:334: error: implicit declaration of function 'fc_remote_port_unblock'
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
5.1.3. Maximum Response Code
The Maximum Response Code field specifies the maximum time allowed
before sending a responding Report. The actual time allowed, called
the Maximum Response Delay, is represented in units of milliseconds,
and is derived from the Maximum Response Code as follows:
If Maximum Response Code < 32768,
Maximum Response Delay = Maximum Response Code
If Maximum Response Code >=32768, Maximum Response Code represents a
floating-point value as follows:
0 1 2 3 4 5 6 7 8 9 A B C D E F
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| exp | mant |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Maximum Response Delay = (mant | 0x1000) << (exp+3)
5.1.9. QQIC (Querier's Query Interval Code)
The Querier's Query Interval Code field specifies the [Query
Interval] used by the Querier. The actual interval, called the
Querier's Query Interval (QQI), is represented in units of seconds,
and is derived from the Querier's Query Interval Code as follows:
If QQIC < 128, QQI = QQIC
If QQIC >= 128, QQIC represents a floating-point value as follows:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|1| exp | mant |
+-+-+-+-+-+-+-+-+
QQI = (mant | 0x10) << (exp + 3)
-- rfc3810
#define MLDV2_QQIC(value) MLDV2_EXP(0x80, 4, 3, value)
#define MLDV2_MRC(value) MLDV2_EXP(0x8000, 12, 3, value)
Above macro are defined in mcast.c. but 1 << 4 == 0x10 and 1 << 12 == 0x1000.
So the result computed by original Macro is larger.
Signed-off-by: Yan Zheng <yanzheng@21cn.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Attached is kernel patch for UDP Fragmentation Offload (UFO) feature.
1. This patch incorporate the review comments by Jeff Garzik.
2. Renamed USO as UFO (UDP Fragmentation Offload)
3. udp sendfile support with UFO
This patches uses scatter-gather feature of skb to generate large UDP
datagram. Below is a "how-to" on changes required in network device
driver to use the UFO interface.
UDP Fragmentation Offload (UFO) Interface:
-------------------------------------------
UFO is a feature wherein the Linux kernel network stack will offload the
IP fragmentation functionality of large UDP datagram to hardware. This
will reduce the overhead of stack in fragmenting the large UDP datagram to
MTU sized packets
1) Drivers indicate their capability of UFO using
dev->features |= NETIF_F_UFO | NETIF_F_HW_CSUM | NETIF_F_SG
NETIF_F_HW_CSUM is required for UFO over ipv6.
2) UFO packet will be submitted for transmission using driver xmit routine.
UFO packet will have a non-zero value for
"skb_shinfo(skb)->ufo_size"
skb_shinfo(skb)->ufo_size will indicate the length of data part in each IP
fragment going out of the adapter after IP fragmentation by hardware.
skb->data will contain MAC/IP/UDP header and skb_shinfo(skb)->frags[]
contains the data payload. The skb->ip_summed will be set to CHECKSUM_HW
indicating that hardware has to do checksum calculation. Hardware should
compute the UDP checksum of complete datagram and also ip header checksum of
each fragmented IP packet.
For IPV6 the UFO provides the fragment identification-id in
skb_shinfo(skb)->ip6_frag_id. The adapter should use this ID for generating
IPv6 fragments.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The xtTruncate code was only doing this for leaf pages. When a file is
horribly fragmented, we may truncate a file leaving an internal page with
an invalid head.next field, which may cause a stale page to be referenced.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
If a BPA 100/105 device contains more then one interface then ignore the
additional interfaces, because they are unused.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the HCI security filter with support for the Extended
Inquiry Response (EIR) feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch contains the big cleanup of the HCI UART driver. The uneeded
header files are removed and their structure declarations are moved into
the protocol implementations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves rfcomm_crc_table[] into the RFCOMM core, because there
is no need to keep it in a separate file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the Documentation/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in example code in Documentation/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 071 release is needed to handle the input changes. Older versions
will work properly with module-based systems, but not for users that
build input stuff into the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a number of sparse warnings from the latest sparse
snapshot being generated from the drivers/base build. The
main culprits are due to the initialisation functions not
being declared in a header file.
Also, the firmware.c file should include <linux/device.h>
to get the prototype of firmware_register() and
firmware_unregister().
This patch moves the init function declerations from the
init.c file to the base.h, and ensures it is included in
all the relevant c sources. It also adds <linux/device.h>
to the included headers for firmware.c.
The patch does not solve all the sparse errors generated,
but reduces the count significantly.
drivers/base/core.c:161:1: warning: symbol 'devices_subsys' was not declared. Should it be static?
drivers/base/core.c:417:12: warning: symbol 'devices_init' was not declared. Should it be static?
drivers/base/sys.c:253:6: warning: symbol 'sysdev_shutdown' was not declared. Should it be static?
drivers/base/sys.c:326:5: warning: symbol 'sysdev_suspend' was not declared. Should it be static?
drivers/base/sys.c:428:5: warning: symbol 'sysdev_resume' was not declared. Should it be static?
drivers/base/sys.c:450:12: warning: symbol 'system_bus_init' was not declared. Should it be static?
drivers/base/bus.c:133:1: warning: symbol 'bus_subsys' was not declared. Should it be static?
drivers/base/bus.c:667:12: warning: symbol 'buses_init' was not declared. Should it be static?
drivers/base/class.c:759:12: warning: symbol 'classes_init' was not declared. Should it be static?
drivers/base/platform.c:313:12: warning: symbol 'platform_bus_init' was not declared. Should it be static?
drivers/base/cpu.c:110:12: warning: symbol 'cpu_dev_init' was not declared. Should it be static?
drivers/base/firmware.c:17:5: warning: symbol 'firmware_register' was not declared. Should it be static?
drivers/base/firmware.c:23:6: warning: symbol 'firmware_unregister' was not declared. Should it be static?
drivers/base/firmware.c:28:12: warning: symbol 'firmware_init' was not declared. Should it be static?
drivers/base/init.c:28:13: warning: symbol 'driver_init' was not declared. Should it be static?
drivers/base/dmapool.c:174:10: warning: implicit cast from nocast type
drivers/base/attribute_container.c:439:1: warning: symbol 'attribute_container_init' was not declared. Should it be static?
drivers/base/power/runtime.c:76:6: warning: symbol 'dpm_set_power_state' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: remove custom-made hotplug handler
Now that all input devices are registered with sysfs we can remove
old custom-made hotplug handler and crate a standard one.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This creates symlinks in /sys/class/input/ to the nested class devices
to help userspace cope with the nesting.
Unfortunatly udev still needs to be updated as it can't handle symlinks
properly here :(
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Input: show sysfs path in /proc/bus/input/devices
Show that sysfs and phys path are different objects.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch allows struct class_device to be nested, so that another
struct class_device can be the parent of a new one, instead of only
having the struct class be the parent. This will allow us to
(hopefully) fix up the input and video class subsystem mess.
But please people, don't go crazy and start making huge trees of class
devices, you should only need 2 levels deep to get everything to work
(remember to use a class_interface to get notification of a new class
device being added to the system.)
Oh, this also allows us to have the possibility of potentially, someday,
moving /sys/block into /sys/class. The main hindrance is that pesky
/dev numberspace issue...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A "coldplug + udevstart" can be simple like this:
for i in /sys/block/*/*/uevent; do echo 1 > $i; done
for i in /sys/class/*/*/uevent; do echo 1 > $i; done
for i in /sys/bus/*/devices/*/uevent; do echo 1 > $i; done
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: pass interface to class intreface methods
Pass interface as argument to add() and remove() class interface
methods. This way a subsystem can implement generic add/remove
handlers and then call interface-specific ones.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: cleanup - remove i2o_device_class
I2O devices reside on their own bus so there should be no reason
to also have i2c_device class that mirros i2o bus.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2O: remove i2o_device_class_interface misuse
The intent of class interfaces was to provide different
'views' at the same object, not just run some code every
time a new class device is registered. Kill interface
structure, make class core register default attributes
and set up sysfs links right when registering class
devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move call to kobject_hotplug() above code that adds interfaces
to a class device, otherwise children's hotplug events may reach
userspace first.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch teaches "usb_device" about the new driver model wakeup support:
- It updates device wakeup capabilities when entering a configuration
with the WAKEUP attribute;
- During suspend processing it consults the policy bit to see
whether it should enable wakeup for that device. (This resolves
a FIXME to not assume the answer is always "yes"; some devices
lie about supporting remote wakeup.)
Support for root hubs and the HCDs is separate (and more complex).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a refresh of an earlier patch to add "wakeup" support to the
PM core model. This provides per-device bus-neutral control of the
use of wakeup events.
* "struct device_pm_info" has two bits that are initialized as
part of setting up the enclosing struct device:
- "can_wakeup", reflecting hardware capabilities
- "may_wakeup", the policy setting (when CONFIG_PM)
* There's a writeable sysfs "wakeup" file, with one of two values:
- "enabled", when the policy is to allow wakeup
- "disabled", when the policy is not to allow it
- "" if the device can't currently issue wakeups
By default, wakeup is enabled on all devices that support it. If its
driver doesn't support it ... treat it as a bug. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The document porting.txt in Documentation/driver-model says:
When a device is successfully bound to a device
I think it should say:
When a device is successfully bound to a driver
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was recently given an old Travan tape drive and asked to do something
useful with it. The ide-scsi + st (+serverworks ide controller) combo
results in a hard lockup of the machine which I have not had the energy to
debug, so I turned to ide-tape (which seems to work). The system in
question debian stable, using udev to manage /dev.
The following patch to ide-tape.c allows udev to create the cdev nodes for
my drive.
Cc: Gadi Oxman <gadio@netvision.net.il>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use get_unaligned for possibly-unaligned multi-byte accesses to the
ATA device identify response buffer.
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The non-handled failure cases of the Fabric Login mailbox
command handling logic would incorrectly mark the fcport as
dead and not allow the standard port-down-retry-count logic
to manage the transition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch adds the 'new comm' interface, which modern AAC based
adapters that are less than a year old support in the name of much
improved performance. These modern adapters support both the legacy and
the 'new comm' interfaces.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch resolves a compiler warning on 64 bit architectures.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The compat field needed to be in cpu order.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch uses the adapter supplemental information AdapterTypeText as
the default for the array name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Mark Haverkamp <markh@osdl.org>
Received from Mark Salyzyn.
This patch changes the driver over to utilizing the DMA_64BIT_MASK and
DMA_32BIT_MASK manifests.
Applies to the scsi-rc-fixes-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Rejects fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Bellido Nicolas
The AAED-2000 is equiped with an 640x480 LCD.
This adds the parameters that will be passed to the AAEC-2000 platform code.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAEC-2000 has an ARM PrimeCell PL110 Color LCD Controller.
This patch contains the platform glue that will be used by specific boards.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Here is a preliminary clock interface support for the AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
This adds platform code for MTD devices on AAEC-2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
linux/config.h is not necessary in hardware.h, while asm/sizes.h and asm/arch//aaec2000.h will be used later.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
The AAED-2000 board has GPIO pins on an external port.
This patch adds the defines, and do the necessary mapping.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Add defines for GPIO registers on the AAEC-2000 processor.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This is the PXA2xx common IRDA driver, plus platform support
for Lubbock and Mainstone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
From: Daniel Jacobowitz <dan@debian.org>
> I also fixed a bug that confused me greatly while trying to debug: one
> SIGILL has long been a SIGSEGV because of some broken RISCOS
> compatibility code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
I noticed that the same typo (i before c in associated) showed up twice
in the file kernel/include/linux/mmc/mmc.h.
This patch fixes both of the instances I found with this mistake. The
typos are in comments and should have no affect on working code.
E
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
This adds support for the RTC and nvram on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants. Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep). Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value. From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
This patch gives support for the CS8900A ethernet chip on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and related annotations for amd64 - swiotlb code is shared, but
prototypes are not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- ->releasepage() annotated (s/int/gfp_t), instances updated
- missing gfp_t in fs/* added
- fixed misannotation from the original sweep caught by bitwise checks:
XFS used __nocast both for gfp_t and for flags used by XFS allocator.
The latter left with unsigned int __nocast; we might want to add a
different type for those but for now let's leave them alone. That,
BTW, is a case when __nocast use had been actively confusing - it had
been used in the same code for two different and similar types, with
no way to catch misuses. Switch of gfp_t to bitwise had caught that
immediately...
One tricky bit is left alone to be dealt with later - mapping->flags is
a mix of gfp_t and error indications. Left alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Beginning of gfp_t annotations:
- -Wbitwise added to CHECKFLAGS
- old __bitwise renamed to __bitwise__
- __bitwise defined to either __bitwise__ or nothing, depending on
__CHECK_ENDIAN__ being defined
- gfp_t switched from __nocast to __bitwise__
- force cast to gfp_t added to __GFP_... constants
- new helper - gfp_zone(); extracts zone bits out of gfp_t value and casts
the result to int
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ian Campbell
As noted by Uli Luckas in the comments of 3025 there is a typo in the i2s platform device. The i2s platform device refers to the i2c resources.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add platform data for framebuffer for the
onboard LCD module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Change set_s3c2410fb_info to s3c2410_fb_set_platdata
and use kmalloc() for the copy of the information it
is passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
We already had a mapping for the msf, but we didn't have any
register definitions for it yet.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ian Campbell
The sparse warning initially surfaced in sound/arm/pxa2xx-ac97.c
because it was using u32 * variables to hold the unsigned long *
register addresses.
I submitted an ALSA patch for this http://thread.gmane.org/gmane.linux.alsa.devel/27804 issue and it was suggested that it might be preferable to change the register
definitions to use u32.
Most other subarches seem to use u32 for their register type, at least
the ones which use a __REG macro (like the PXA) do. Nico indicated in
the thread above that he wouldn't mind this patch.
Changing the type required fixes for opposite warnings in the pxa2xx usb
gadget code but that was the only new warning introduced on defconfig
or lubbock, mainstone and our own PXA255 boards.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add generic values for the parameters to the
s3c2410_gpio_cfgpin() function, so that a caller
does not need to know the exact constant for
the specified pin.
This is very useful for the case where a driver
is passed a gpio pin number and needs to reconfigure
the pin's function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Here's an ARM assembly SHA1 implementation to replace the default C
version. It is approximately 50% faster than the generic C version. On
an XScale processor running at 400MHz:
generic C version: 9.8 MB/s
my version: 14.5 MB/s
This code is useful to quite a few callers in the tree:
crypto/sha1.c: sha_transform(sctx->state, sctx->buffer, temp);
crypto/sha1.c: sha_transform(sctx->state, &data[i], temp);
drivers/char/random.c: sha_transform(buf, (__u8 *)r->pool+i, buf + 5);
drivers/char/random.c: sha_transform(buf, (__u8 *)data, buf + 5);
net/ipv4/syncookies.c: sha_transform(tmp + 16, (__u8 *)tmp, tmp + 16 + 5);
Signed-off-by: Nicolas Pitre <nico@cam.org>
Seems to work fine on big-endian as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for 36-bit static mapped I/O. While there
are no platforms in the tree ATM that use it, it has been tested
tested on the IXP2350 NPU and I would like to get the support for
that chipset upstream one piece at a time. There are also other
Intel chipset ports in development that are waiting on this to go
upstream.
The patch replaces the print formats for physical addresses with
%016llx which will create a bit extraneous output on 32-bit systems,
but I think that is cleaner than having #ifdefs, specially since
users will only see the output in error cases.
Depends on 3016/1.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Convert map_desc.physical to map_desc.pfn. This allows us to add
support for 36-bit addressed physical devices in the static maps
without having to resort to u64 variables.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is nothing special about having the init code separate from
the common code, so combine the two.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The common oprofile code assumes the name "PMU" (from Intel's
performance management unit). This is misleading when we
start adding oprofile support for other machine types which
don't use the same terminology. Call it op_arm_* instead of
pmu_*.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The oprofile suspend/resume was missing locking. If we failed
to start oprofile on resume, we still reported that it was
enabled. Instead, disable oprofile on error.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make ARM independent of the way bootmem operates internally. We
now map each node as we initialise it, and place the bootmem bitmap
inside each node, rather than all in the first node.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warnings in arch/arm/kernel/module.c,
arch/arm/mm/consistent.c, drivers/pcmcia/sa1111_generic.c,
and platform support files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sc instruction emulation can't be done the same way on 32-bit
as 64-bit yet, but this should work OK.
Signed-off-by: Paul Mackerras <paulus@samba.org>
EBSA110 only requires hardware.h to be included for a couple of
files. Move the include there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Including asm/hardware.h into asm/io.h can cause #define clashes
between platform specific definitions and driver local definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- 100msec sleep is a little excessive, lots of requests can complete
in that timeframe. Use 10msec instead.
- Rename QUEUE_FLAG_BYPASS to QUEUE_FLAG_ELVSWITCH to indicate what
is going on.
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch reimplements elevator switch. This patch assumes generic
dispatch queue patchset is applied.
* Each request is tagged with REQ_ELVPRIV flag if it has its elevator
private data set.
* Requests which doesn't have REQ_ELVPRIV flag set never enter
iosched. They are always directly back inserted to dispatch queue.
Of course, elevator_put_req_fn is called only for requests which
have its REQ_ELVPRIV set.
* Request queue maintains the current number of requests which have
its elevator data set (elevator_set_req_fn called) in
q->rq->elvpriv.
* If a request queue has QUEUE_FLAG_BYPASS set, elevator private data
is not allocated for new requests.
To switch to another iosched, we set QUEUE_FLAG_BYPASS and wait until
elvpriv goes to zero; then, we attach the new iosched and clears
QUEUE_FLAG_BYPASS. New implementation is much simpler and main code
paths are less cluttered, IMHO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch kills max_back_kb handling from elv_dispatch_sort() and
kills max_back_kb field from struct request_queue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Currently, both generic elevator code and specific ioscheds
participate in the management and usage of last_merge. This
and the following patches move last_merge handling into
generic elevator code.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch updates all four ioscheds to use generic dispatch
queue. There's one behavior change in as-iosched.
* In as-iosched, when force dispatching
(ELEVATOR_INSERT_BACK), batch_data_dir is reset to REQ_SYNC
and changed_batch and new_batch are cleared to zero. This
prevernts AS from doing incorrect update_write_batch after
the forced dispatched requests are finished.
* In cfq-iosched, cfqd->rq_in_driver currently counts the
number of activated (removed) requests to determine
whether queue-kicking is needed and cfq_max_depth has been
reached. With generic dispatch queue, I think counting
the number of dispatched requests would be more appropriate.
* cfq_max_depth can be lowered to 1 again.
Original from Tejun Heo, modified version applied.
Signed-off-by: Jens Axboe <axboe@suse.de>
Implements generic dispatch queue which can replace all
dispatch queues implemented by each iosched. This reduces
code duplication, eases enforcing semantics over dispatch
queue, and simplifies specific ioscheds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch moves the XICS interrupt controller code into the
platforms/pseries directory, since it only appears on pSeries
machines. If it ever appears on some other machine we can move it to
sysdev, although xics.c itself will need a bunch of changes in that
case to remove pSeries specific assumptions.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes try_module_get race in elevator_find.
try_module_get should always be called with the spinlock protecting
what the module init/cleanup routines register/unregister to held. In
the case of elevators, we should be holding elv_list to avoid it going
away between spin_unlock_irq and try_module_get.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
disk stat when "now" is different from disk->stamp. Otherwise, we
are again needlessly adding zero to the stats.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
struct gendisk has these two fields: stamp, stamp_idle. Update to
stamp_idle is always in sync with stamp and they are always the same.
Therefore, it does not add any value in having two fields tracking
same timestamp. Suggest to remove it.
Also, we should only update gendisk stats with non-zero value.
Advantage is that we don't have to needlessly calculate memory address,
and then add zero to the content.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Simplify user_mad.c code in a few places, and convert from kmalloc() +
memset() to kzalloc(). This also fixes a theoretical race window by
not accessing packet->length after posting the send buffer (the send
could complete and packet could be freed before we get to the return
statement at the end of ib_umad_write()).
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The conversion of user_mad.c to the new MAD send API was slightly off:
in a few places, we used packet->msg instead of packet->msg->mad when
referring to the actual data buffer, which ended up corrupting the
underlying data structure and crashing when we free an invalid pointer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows us to also use entry_64.S from the merged tree and reverts
the setup_64.c part of fda262b897.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Optimise attribute revalidation when hardlinking. Add post-op attributes
for the directory and the original inode.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
"Optional" means that the close call will not fail if the getattr
at the end of the compound fails.
If it does succeed, try to refresh inode attributes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since the directory attributes change every time we CREATE a file,
we might as well pick up the new directory attributes in the same
compound.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs_lookup() used to consult a lookup cache before trying an actual wire
lookup operation. The lookup cache would be invalid, of course, if the
parent directory's mtime had changed, so nfs_lookup performed an inode
revalidation on the parent.
Since nfs_lookup() doesn't use a cache anymore, the revalidation is no
longer necessary. There are cases where it will generate a lot of
unnecessary GETATTR traffic.
See http://bugzilla.linux-nfs.org/show_bug.cgi?id=9
Test-plan:
Use lndir and "rm -rf" and watch for excess GETATTR traffic or application
level errors.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Since we almost always call nfs_end_data_update() after we called
nfs_refresh_inode(), we now end up marking the inode metadata
as needing revalidation immediately after having updated it.
This patch rearranges things so that we mark the inode as needing
revalidation _before_ we call nfs_refresh_inode() on those operations
that need it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow nfs_refresh_inode() also to update attributes on the inode if the
RPC call was sent after the last call to nfs_update_inode().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We still had an old copy of i8259.h lying around; this gets rid of it
and corrects the callers of i8259_init and i8259_irq.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since I sent the patch to purge bootinfo.h from ARCH=powerpc and
ARCH=ppc64, setup-common.c has come into existence, and another
#include of bootinfo.h slipped in. This patch removes it. It also
removes include/asm-ppc64/bootinfo.h, which somehow survived the
previous patch which was supposed to remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For the current time idle_6xx only applies to 6xx ppc32 CPUs
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit id 6142891a0c
Andi Kleen reports that it seems to break things for some people,
and since it's purely a small optimization, revert it for now.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In arch/ia64/kernel/ptrace.c there is a test for a peek or poke of a
register image (in register backing storage).
The test can be unnecessarily long (and occurs while holding the tasklist_lock).
Especially long on a large system with thousands of active tasks.
The ptrace caller (presumably a debugger) specifies the pid of
its target and an address to peek or poke. But the debugger could be
attached to several tasks.
The idea of find_thread_for_addr() is to find whether the target address
is in the RBS for any of those tasks.
Currently it searches the thread-list of the target pid. If that search
does not find a match, and the shared mm-struct's user count indicates
that there are other tasks sharing this address space (a rare occurrence),
a search is made of all the tasks in the system.
Another approach can drastically shorten this procedure.
It depends upon the fact that in order to peek or poke from/to any task,
the debugger must first attach to that task. And when it does, the
attached task is made a child of the debugger (is chained to its children list).
Therefore we can search just the debugger's children list.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an issue found in drivers/cpufreq/cpufreq_stats.c by Coverity.
Error reported:
CID: 2642
Checker: NULL_RETURNS (help)
File: /export2/p4-coverity/mc2/linux26/drivers/cpufreq/cpufreq_stats.c
Function: cpufreq_stats_create_table
Description: Dereferencing NULL value "data"
Patch description:
The return of cpufreq_cpu_get can be NULL, check return code and return
-EINVAL if it is NULL.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
flush_tlb_all() can be a scaling issue on large SGI Altix systems
since it uses the global call_lock and always executes on all cpus.
When a process enters flush_tlb_range() to purge TLBs for another
process, it is possible to avoid flush_tlb_all() and instead allow
sn2_global_tlb_purge() to purge TLBs only where necessary.
This patch modifies flush_tlb_range() so that this case can be handled
by platform TLB purge functions and updates ia64_global_tlb_purge()
accordingly. sn2_global_tlb_purge() now calculates the region register
value from the mm argument introduced with this patch.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
unaligned structures coming in off the wire
gcc on arm processors generates very odd code with pragma pack specified -
although it does pack the structures in some sense - it does not allow you
to access unaligned elements in nested structures at the right offset as other
architectures do. Oddly enough though, specifying the structures as packed
the long way - one by one with the packed attribute does work. Rather than
fighting over whether this is a gcc bug or some obscure side effect
of pragma pack, it is easier to do what most (all but 96 other places in
the kernel) do - and replace pragma pack with dozens of attribute(packed)
structure qualifiers. Much more verbose ... but at least it works.
Signed-off-by: David Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com> CG: -----------------------------------------------------------------------
Add some initial support for detecting and reporting catastrophic
errors reported by Mellanox HCAs. We start a periodic timer which
polls the catastrophic error reporting buffer in device memory. If an
error is detected, we dump the contents of the buffer for port-mortem
debugging, and report a fatal asynchronous error to higher levels.
In the future we can try to recover from these errors by resetting the
device, but this will require some work in higher-level code as well.
Let's get this in now, so that we at least get catastrophic errors
reported in logs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This bug is responsible for causing the infamous "Treason uncloaked"
messages that's been popping up everywhere since the printk was added.
It has usually been blamed on foreign operating systems. However,
some of those reports implicate Linux as both systems are running
Linux or the TCP connection is going across the loopback interface.
In fact, there really is a bug in the Linux TCP header prediction code
that's been there since at least 2.1.8. This bug was tracked down with
help from Dale Blount.
The effect of this bug ranges from harmless "Treason uncloaked"
messages to hung/aborted TCP connections. The details of the bug
and fix is as follows.
When snd_wnd is updated, we only update pred_flags if
tcp_fast_path_check succeeds. When it fails (for example,
when our rcvbuf is used up), we will leave pred_flags with
an out-of-date snd_wnd value.
When the out-of-date pred_flags happens to match the next incoming
packet we will again hit the fast path and use the current snd_wnd
which will be wrong.
In the case of the treason messages, it just happens that the snd_wnd
cached in pred_flags is zero while tp->snd_wnd is non-zero. Therefore
when a zero-window packet comes in we incorrectly conclude that the
window is non-zero.
In fact if the peer continues to send us zero-window pure ACKs we
will continue making the same mistake. It's only when the peer
transmits a zero-window packet with data attached that we get a
chance to snap out of it. This is what triggers the treason
message at the next retransmit timeout.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This just makes sure that a thread's expiry times can't get reset after
it clears them in do_exit.
This is what allowed us to re-introduce the stricter BUG_ON() check in
a362f463a6.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 3de463c7d9.
Roland has another patch that allows us to leave the BUG_ON() in place
by just making sure that the condition it tests for really is always
true.
That goes in next.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 32-bit platforms, these convert from kernel virtual addresses
to real (physical addresses), like tophys/tovirt but they use
the same register for the source and destination. On 64-bit
platforms, they do nothing because the hardware ignores the top
two bits of the address in real mode.
These new macros are used in fpu.S now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
do_dabr() is not relevant on 40x or Book-E processors so dont build it
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In readiness for 64k pages, when THREAD_SIZE will be less than
PAGE_SIZE, ppc64 uses kmalloc() rather than __get_free_pages() to
allocate kernel stacks, and since thread_info.h was merged, so does
ppc32. However that adds some overhead which we don't really want
when PAGE_SIZE <= THREAD_SIZE (including all ppc32 machines), so this
patch avoids it.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save for the header #define, ppc32 and ppc64 versions of parport.h are
identical. This patch merges them.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With ARCH=powerpc we assume the presence of a device tree, so we don't
require any support for the old bi_recs method of passing boot
parameters. Likewise, we've never needed it for ppc64, but we still
had an include/asm-ppc64/bootinfo.h from which nothing was used. This
patch removes that file, and all references to it in arch/ppc64 and
arch/powerpc. A related, unused variable 'boot_mem_size' is also
removed from setup_32.c. The bootinfo stuff remains in ARCH=ppc for
the time being.
Built and booted on Power5 (ARCH=ppc64 and ARCH=powerpc), built for
32-bit powermac (ARCH=powerpc and ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and use setup_64.c from the merged tree instead. The only difference
between them was the code to set up the syscall maps.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There has been a need expressed for dma_addr_t to be 64 bits on PPC64.
This patch does that.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent addition of __deprecated to the declarations for
find_devices etc. produces a whole pile of warnings from the
ppc32 code. Since those functions still work perfectly well on
ppc32, which doesn't have hotplug support for anything in the
OF device tree, and we don't have time to fix that code now,
remove the __deprecated markings for now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace the mcr53c8xx roll your own ktime_... macros with the correct
time_after() et al.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a silly off-by-one error in the code that updates the expiration
of posix CPU timers, causing them to not be properly updated when they
hit exactly on their expiration time (which should be the normal case).
This causes them to then fire immediately again, and only _then_ get
properly updated.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've seen similar failure on alpha.
Obviously, someone forgot to convert sg->handle stuff for
PCI gart case.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
fsck_hfs reveals lots of temporary files accumulating in the hidden
directory "\000\000\000HFS+ Private Data". According to the HFS+
documentation these are files which are unlinked while in use. However,
there may be a bug in the Linux hfsplus implementation which causes this to
happen even when the files are not in use. It looks like the "opencnt"
field is never initialized as (I think) it should be in hfsplus_read_inode.
This means that a file can appear to be still in use when in fact it has
been closed. This patch seems to fix it for me.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Although this message is having the intended effect of causing wireless
driver maintainers to upgrade their code, I never should have merged this
patch in its present form. Leading to tons of bug reports and unhappy
users.
Some wireless apps poll for statistics regularly, which leads to a printk()
every single time they ask for stats. That's a little bit _too_ much of a
reminder that the driver is using an old API.
Change this to printing out the message once, per kernel boot.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With CONFIG_SMP=n:
*** Warning: "cpu_online_map" [drivers/firmware/dcdbas.ko] undefined!
due to set_cpus_allowed().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mpic interrupt controller driver (used on G5 and early pSeries among
others) has a bug where it doesn't get the right virtual address for the
timer registers. It causes the driver to poke at the MMIO space of
whatever has been mapped just next to it (ouch !) when initializing and
causes boot failures on some IBM machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The NUMA counters in struct per_cpu_pageset (linux/mmzone.h) are never
cleared today. This works ok for CPU 0 on NUMA machines because
boot_pageset[] is already zero, but for other CPU:s this results in
uninitialized counters.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are still a couple of cases where md threads (the resync/recovery
thread) is not interruptible since the change to use kthreads. All places
there it tests "signal_pending", it should also test kthread_should_stop,
as with this patch.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ian Campbell
Sparse complains about the definition of generic_fls in asm-arm/bitops.h:
CHECK /home/icampbell/devel/kernel/2.6/arch/arm/mach-pxa/viper.c
include2/asm/bitops.h:350:34: error: marked inline, but without a definition
The definition is unnecessary since linux/bitops.h defines generic_fls before including asm/bitops.h and asm/bitops.h should not be included directly. There are still some places where asm/bitops.h is directly included, but I think that code should be fixed. I was a little wary of the patch for this reason but lubbock, mainstone and assabet all build OK and so do my in house boards...
ARM is the only arch with the generic_fls prototype in this way.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were computing the wrong address for the MPIC timer registers,
so when we went to initialize them we would have been hitting some
unrelated ioremap... oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Talk about buggy firmware... the OF on the Longtrail returns 0
from the claim client service rather than -1 when the claim fails.
It also has no device_type on the /memory node and blows up if
the output buffer for package-to-path is too big.
This also fixes a bug with calling alloc_up with align == 0, where
we did _ALIGN_UP(alloc_bottom, 0) which will end up as 0.
Lastly, we now check the return value (in r3) from calling the
prom, and return -1 from call_prom if we get a negative value back.
That is supposed to indicate that the requested client service
doesn't exist.
Signed-off-by: Paul Mackerras <paulus@samba.org>
SMP still needs more work but UP gets as far as starting userspace
at least. This uses the 64-bit-style code for spinning up the cpus.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the machine's clock is set to a bogus value, this check resulted
in userland waiting effectively forever for the RTC value to change,
so remove the check.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt-tree parsing code wasn't offsetting interrupt numbers
by 16 on 32-bit platforms with an i8259 interrupt controller, and
it was confused about the encoding of interrupt sense and level
(which is different for i8259 and openpic interrupt controllers,
just to make things interesting).
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is so that the 32-bit CHRP code can use it. The MPC106
initialization code is now in arch/powerpc/sysdev/grackle.c and
is controlled by CONFIG_PPC_MPC106.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates a new arch/powerpc/kernel/setup-common.c with various
bits that setup_32.c and setup_64.c had in common - functions like
machine_shutdown/restart/power_off, show_cpuinfo, set_preferred_console
etc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits arch/ppc64/kernel/rtas.c into arch/powerpc/kernel/rtas.c,
which contains generic RTAS functions useful on any CHRP platform,
and arch/powerpc/platforms/pseries/rtas-fw.[ch], which contain
some pSeries-specific firmware flashing bits. The parts of rtas.c
that are to do with pSeries-specific error logging are protected
by a new CONFIG_RTAS_ERROR_LOGGING symbol. The inclusion of rtas.o
is controlled by the CONFIG_PPC_RTAS symbol, and the relevant
platforms select that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset. i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now. This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines a CONFIG_INDIRECT_PCI symbol to control whether it
gets used or not, and fixes the Kconfig to select that symbol for
platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
ras.o is only built for CONFIG_PPC_PSERIES, so move it into
arch/powerpc/platforms/pseries. Update Makefiles to suit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
GCC 3.3.3 barfs on the trailing \n" in the HMT macros.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somewhere along the line we got two definitions of set_tb(). They look to
be identical although they're not textually identical. So remove the #ifdef
CONFIG_PPC64 version, leaving the common version in time.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed of_show_percpuinfo and just report CPU frequency in generic
show_cpuinfo code.
* Killed OCP and PPC_SYS related code which doesn't belong in the
merge tree
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to initialize some control SPRS for timers on Book-E before
we start taking decrementer interrupts.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A recent patch updated the name of pci_assign_all_busses to
pci_assign_all_buses. This instance of its use wasn't corrected
by the original patch to use the new name.
Builds cleanly on ads8272.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powerpc: Fix types.h
I noticed that Paul had already pulled the version of types.h that
is missing the config.h include into the merge tree - this patch adds
it back in.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On !CONFIG_PPC_MULTIPLATFORM _machine is defined as 0. This is ok, but
we can't assign a value to _machine then.
We may not have CONFIG_PCI available, so only build in support for
find_parent_pci_resource(), request_OF_resource(), release_OF_resource()
if PCI is enabled. This is probably not the long term fix but works out
for now.
Make reg_property64 contain 64-bit elements on a 32-bit machine.
Mark the deprecated prom.c functions as __deprecated.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Its valid for ppc_md.set_rtc_time to be NULL. We need to check
that its non-NULL before trying to update the RTC.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
James Ketrenos wrote:
> [3/4] Use the tx_headroom and reserve requested space.
This patch introduced a compile problem; patch below corrects this.
Fixed compilation error due to not passing tx_headroom in
ieee80211_tx_frame.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When reserving an PCI quirk, note that in the kernel bootup messages.
Also, parse the strange PIIX4 device resources - they should get their
own PCI resource quirks, but for now just print out what it finds to
verify that the code does the right thing.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix setting of the broadcast address when the netmask is set via
SIOCSIFNETMASK in Linux 2.6. The code wanted the old value of
ifa->ifa_mask but used it after it had already been overwritten with
the new value.
Signed-off-by: David Engel <gigem@comcast.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Add kernel-doc to skbuff.h, skbuff.c to eliminate kernel-doc warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
skb_prev is assigned from skb, which cannot be NULL. This patch removes the
unnecessary NULL check.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Remove the variable nlk & call to nlk_sk as it does not have any side effect.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Now that we've switched over to storing MTUs in the xfrm_dst entries,
we no longer need the dst's get_mss methods. This patch gets rid of
them.
It also documents the fact that our MTU calculation is not optimal
for ESP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch kills a redundant rcu_dereference on fa->fa_info in fib_trie.c.
As this dereference directly follows a list_for_each_entry_rcu line, we
have already taken a read barrier with respect to getting an entry from
the list.
This read barrier guarantees that all values read out of fa are valid.
In particular, the contents of structure pointed to by fa->fa_info is
initialised before fa->fa_info is actually set (see fn_trie_insert);
the setting of fa->fa_info itself is further separated with a write
barrier from the insertion of fa into the list.
Therefore by taking a read barrier after obtaining fa from the list
(which is given by list_for_each_entry_rcu), we can be sure that
fa->fa_info contains a valid pointer, as well as the fact that the
data pointed to by fa->fa_info is itself valid.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
It's fairly simple to resize the hash table, but currently you need to
remove and reinsert the module. That's bad (we lose connection
state). Harald has even offered to write a daemon which sets this
based on load.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The code to handle the /proc interface can be cleaned up in several places:
* use seq_file for read
* don't need to remember all the filenames separately
* use for_online_cpu's
* don't vmalloc a buffer for small command from user.
Committer note:
This patch clashed with John Hawkes's "[NET]: Wider use of for_each_*cpu()",
so I fixed it up manually.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
These are cleanup patches for pktgen that can go in 2.6.15
Can use kzalloc in a couple of places.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
pktgen is calling kmalloc GFP_KERNEL and vmalloc with lock held.
The simplest fix is to turn the lock into a semaphore, since the
thread lock is only used for admin control from user context.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In 'net' change the explicit use of for-loops and NR_CPUS into the
general for_each_cpu() or for_each_online_cpu() constructs, as
appropriate. This widens the scope of potential future optimizations
of the general constructs, as well as takes advantage of the existing
optimizations of first_cpu() and next_cpu(), which is advantageous
when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
bte_copy() calls calls get_nasid(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead.
It is OK if we migrate off node.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate the passing in of a scratch buffer used for locating the
reserved page setup for XPC.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
XPC needs to be changed to support up to 16k nasids on an SGI Altix system.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch addresses a few issues with the open/close protocol that
were revealed by the newly added disengage functionality combined
with more extensive testing.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change alloc_response_msg() in mad_rmpp.c to return the struct
it allocates directly (or an error code a la ERR_PTR), rather than
returning a status and passing the struct back in a pointer param.
This simplifies the code and gets rid of warnings like
drivers/infiniband/core/mad_rmpp.c: In function nack_recv:
drivers/infiniband/core/mad_rmpp.c:192: warning: msg may be used uninitialized in this function
with newer versions of gcc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In arch/ia64 change the explicit use of a for-loop using NR_CPUS into the
general for_each_online_cpu() construct. This widens the scope of potential
future optimizations of the general constructs, as well as takes advantage
of the existing optimizations of first_cpu() and next_cpu(), which is
advantageous when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In arch/ia64 change the explicit use of for-loops and NR_CPUS into the
general for_each_cpu() or for_each_online_cpu() constructs, as
appropriate. This widens the scope of potential future optimizations
of the general constructs, as well as takes advantage of the existing
optimizations of first_cpu() and next_cpu().
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The new ia64 assembler uses slot 1 for the offset of a long (2-slot)
instruction and the old assembler uses slot 2. The 2.6 kernel assumes
slot 2 and won't boot when the new assembler is used:
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1433
This patch will work with either slot 1 or 2.
Patch provided by H.J. Lu
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the "siblings" field value in /proc/cpuinfo so that it now shows the
number of siblings as seen by OS, instead of what is available from
hardware perspective.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The simscsi code at present overflows an int if it's given a large
disk image. The attached patch increases the possible size to 128G.
While it's unlikely that anyone will want to use SKI with such a
large drive, the same framework is currently being used for various
virtualisation experiments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The UC transport does not support RDMA reads or atomic operations, so
we shouldn't require or even allow the consumer to set attributes
relating to these operations for UC QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The MAD layer was violating the DMA API by touching data buffers used
for sends after the DMA mapping was done. This causes problems on
non-cache-coherent architectures, because the device doing DMA won't
see updates to the payload buffers that exist only in the CPU cache.
Fix this by having all MAD consumers use ib_create_send_mad() to
allocate their send buffers, and moving the DMA mapping into the MAD
layer so it can be done just before calling send (and after any
modifications of the send buffer by the MAD layer).
Tested on a non-cache-coherent PowerPC 440SPe system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
My alpha build is exploding because asm/atomic.h now needs smb_mb(), which is
over in the (not included) system.h.
I fear what will happen if I include system.h into atomic.h, so let's put the
barriers into their own header file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct some function names in kernel-doc.
Add some kernel-doc descriptions.
Fix some typos.
Remove a few blank lines.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Laurent Riffard <laurent.riffard@free.fr>
This updates .owner field of struct pci_driver.
This allows SYSFS to create the symlink from the driver to the module which
provides it.
$ tree /sys/bus/pci/drivers/agpgart-via/
/sys/bus/pci/drivers/agpgart-via/
|-- 0000:00:00.0 -> ../../../../devices/pci0000:00/0000:00:00.0
|-- bind
|-- module -> ../../../../module/via_agp
|-- new_id
`-- unbind
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This fixes compile problem when CONFIG_FB_PXA is not set.
LD .tmp_vmlinux1
arch/arm/mach-pxa/built-in.o(.text+0x1d74): In function
`spitz_get_hsync_len':
: undefined reference to `pxafb_get_hsync_time'
make: *** [.tmp_vmlinux1] Error 1
3.46user 0.46system 5.10 (0m5.106s) elapsed 77.01%CPU
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This small patch returns the stride/line length of the framebuffer via
sysfs.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix cm_init_qp_init_attr(), cm_init_qp_rtr_attr() and cm_init_qp_rts_attr()
so that they correctly handle the differences between UC and RC QPs. This
fixes problems with setting up UC QPs through the CM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add idr_destroy() calls to the module_exit() functions of the four IB
driver modules that use idrs, so we don't leak idr_layer_cache objects
when these modules are unloaded.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch fixes Oops from sound drivers using generic platform device
but have no suspend/resume callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this patch, uml compile fails with:
LD .tmp_vmlinux1
arch/um/kernel/built-in.o: In function `config_gdb_cb':
arch/um/kernel/tt/gdb.c:129: undefined reference to `TASK_EXTERN_PID'
Tested on i386, but fix needed on x86_64 too AFAICS.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This might be harmless, but looks like a race from code inspection (I
was unable to trigger it). I must admit, I don't understand why we
can't return TIMER_RETRY after 'spin_unlock(&p->sighand->siglock)'
without doing bump_cpu_timer(), but this is what original code does.
posix_cpu_timer_set:
read_lock(&tasklist_lock);
spin_lock(&p->sighand->siglock);
list_del_init(&timer->it.cpu.entry);
spin_unlock(&p->sighand->siglock);
We are probaly deleting the timer from run_posix_cpu_timers's 'firing'
local list_head while run_posix_cpu_timers() does list_for_each_safe.
Various bad things can happen, for example we can just delete this timer
so that list_for_each() will not notice it and run_posix_cpu_timers()
will not reset '->firing' flag. In that case,
....
if (timer->it.cpu.firing) {
read_unlock(&tasklist_lock);
timer->it.cpu.firing = -1;
return TIMER_RETRY;
}
sys_timer_settime() goes to 'retry:', calls posix_cpu_timer_set() again,
it returns TIMER_RETRY ...
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_exit() clears ->it_##clock##_expires, but nothing prevents
another cpu to attach the timer to exiting process after that.
After exit_notify() does 'write_unlock_irq(&tasklist_lock)' and
before do_exit() calls 'schedule() local timer interrupt can find
tsk->exit_state != 0. If that state was EXIT_DEAD (or another cpu
does sys_wait4) interrupted task has ->signal == NULL.
At this moment exiting task has no pending cpu timers, they were cleaned
up in __exit_signal()->posix_cpu_timers_exit{,_group}(), so we can just
return from irq.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. cleanup_timers() sets timer->task = NULL under tasklist + ->sighand locks.
That means that this code in posix_cpu_timer_del() and posix_cpu_timer_set()
lock_timer(timer);
if (timer->task == NULL)
return;
read_lock(tasklist);
put_task_struct(timer->task)
is racy. With this patch timer->task modified and accounted only under
timer->it_lock. Sadly, this means that dead task_struct won't be freed
until timer deleted or armed.
2. run_posix_cpu_timers() collects expired timers into local list under
tasklist + ->sighand again. That means that posix_cpu_timer_del()
should check timer->it.cpu.firing under these locks too.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a shutdown member to struct vio_driver. We also need vio_bus_shutdown()
which converts from struct device to struct vio_dev and knows how to extract
the struct vio_driver.
Original patch adjusted for different location of vio.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
A comment in lpevents.c refers to code that's actually in HvCallEvent.h.
The code in HvCallEvent.h is pretty obvious, so just remove the comment
altogether.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Just set the name field directly in the device_driver structure
contained in the vio_driver struct.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Move include/asm-ppc64/vio.h to include/asm-powerpc/vio.h, that's it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Merge arch/ppc64/kernel/vio.c into arch/powerpc/kernel/vio.c, update
the Makefiles to make it work, and make ARCH=ppc64 still work.
Michael's version put vio.c in arch/powerpc/sysedv but after consolting
Paulus, this one puts it in arch/powerpc/kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event cause
register (ECR), even if we didn't find any entries in the EQ. If we don't,
then there's a window where we miss an EQ entry and then get stuck because
we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug which was reported and diagnosed by
Stefan Jones <stefan.jones@churchillrandoms.co.uk>
IDR trees include a cache of idr_layer objects. There's no way to destroy
this cache, so when we discard an overall idr tree we end up leaking some
memory.
Add and use idr_destroy() for this. v9fs and infiniband also need to use
idr_destroy() to avoid leaks.
Or, we make the cache global, like radix_tree_preload(). Which is probably
better. Later.
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes error handling in sel_make_bools(), where currently we'd
get a memory leak via security_get_bools() and try to kfree() the wrong
pointer if called again.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a possible NULL dereference in policydb_destroy, where
p->type_attr_map can be NULL if policydb_destroy is called to clean up a
partially loaded policy upon an error during policy load. Please apply.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another case of missing call to security_file_permission: aio functions
(namely, io_submit) does not check credentials with security modules.
Below is the simple patch to the problem. It seems that it is enough to
check for rights at the request submission time.
Signed-off-by: Kostik Belousov <kostikbel@gmail.com>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix typos & trailing whitespace.
Add blank lines in a few places.
Remove "AM53C974=" option: driver does not exist.
Restrict to < 80 columns in most places (but don't split formatted
command-line arguments).
Add a few option arguments for completeness.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That's what we've always historically done, and bigger windows seem to
confuse some cardbus bridges. Or something.
Alan reports that this makes the ThinkPad 600x series work properly
again: the 4kB IO window for some reason made IDE DMA not work, which
makes IDE painfully slow even if it works after DMA timeouts.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bursty timers aren't good for anybody, very much including latency for
other programs when we trigger lots of timers in interrupt context. So
set a random limit, after which we'll handle the rest on the next timer
tick.
Noted by Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously it claimed 7MB starting at the 9M point and loaded the
kernel there. That meant that prom_init put the flattened device
tree above 16M. On the 601 that caused the early device tree scan
to fail, since only 16MB are mapped with BATs on the 601. Moving
this down to 8MB allows prom_init to put the flattened device tree
between 15M and 16M, so it works on the 601.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old powermacs have a number of differences from current machines:
- there is no interrupt tree in the device tree, just interrupt
or AAPL,interrupt properties
- the chosen node in the device tree is called /chosen@0
- the OF claim method doesn't map the memory, so we have to do
an explicit map call as well
- there is no /chosen/cpu property on SMP machines
- the NVRAM isn't structured as a set of partitions.
This adapts the merged powermac support code to cope with these
issues.
Signed-off-by: Paul Mackerras <paulus@samba.org>
neigh_changeaddr attempts to delete neighbour timers without setting
nud_state. This doesn't work because the timer may have already fired
when we acquire the write lock in neigh_changeaddr. The result is that
the timer may keep firing for quite a while until the entry reaches
NEIGH_FAILED.
It should be setting the nud_state straight away so that if the timer
has already fired it can simply exit once we relinquish the lock.
In fact, this whole function is simply duplicating the logic in
neigh_ifdown which in turn is already doing the right thing when
it comes to deleting timers and setting nud_state.
So all we have to do is take that code out and put it into a common
function and make both neigh_changeaddr and neigh_ifdown call it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 601 doesn't have the timebase register; instead it has an RTCL
register that counts nanoseconds and wraps at 1000000000, and an
RTCU register that counts seconds. This makes the necessary changes
for the merged time code to use the RTCL/U registers when the kernel
is running on a 601.
Signed-off-by: Paul Mackerras <paulus@samba.org>
neigh_add_timer cannot use add_timer unconditionally. The reason is that
by the time it has obtained the write lock someone else (e.g., neigh_update)
could have already added a new timer.
So it should only use mod_timer and deal with its return value accordingly.
This bug would have led to rare neighbour cache entry leaks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stack traces are very helpful in determining the exact nature of a bug.
So let's print a stack trace when the timer is added twice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As stated in Documentation/atomic_ops.txt, atomic functions
returning values must have the memory barriers both before and after
the operation.
Thanks to DaveM for pointing that out.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On architectures where the char type defaults to unsigned some of the
arithmetic in the AX.25 stack to fail, resulting in some packets being dropped
on receive.
Credits for tracking this down and the original patch to
Bob Brose N0QBJ <linuxhams@n0qbj-11.ampr.org>.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
IPVS used flag NFC_IPVS_PROPERTY in nfcache but as now nfcache was removed the
new flag 'ipvs_property' still needs to be copied. This patch should be
included in 2.6.14.
Further comments from Harald Welte:
Sorry, seems like the bug was introduced by me.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
We should always re-arm an event queue's interrupt in
mthca_tavor_interrupt() if the corresponding bit is set in the event
cause register (ECR), even if we didn't find any entries in the EQ.
If we don't, then there's a window where we miss an EQ entry and then
get stuck because we don't get another EQ event.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This switches the ARCH=ppc64 build to use arch/powerpc/platforms/powermac
instead of arch/ppc64/kernel/pmac*, and deletes the latter set of files.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously it ignored the return value from ppc_md.set_rtc_time,
but in fact the functions that that can point to do return a
useful error code, so return it from set_rtc_time().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved init_boot_display from arch/ppc64/kernel/pmac_setup.c to
arch/ppc64/kernel/btext.c and declared it in asm-ppc64/btext.h.
Call it from init_early rather than pmac_init_early.
Signed-off-by: Paul Mackerras <paulus@samba.org>
... for consistency with ppc32 and to make the powermac merge easier.
Also make it use just a single resource in the host bridge for multiple
consecutive elements of the ranges property.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves smp_space_timers from arch/ppc64/kernel/smp.c to
arch/powerpc/kernel/time.c and makes it initialize last_jiffy[]
instead of paca[].next_jiffy_update_tb, since last_jiffy[] is
now what the time code uses. It also declares smp_space_timers
in include/asm-powerpc/time.h and gets rid of an ifdef in
div128_by_32.
Signed-off-by: Paul Mackerras <paulus@samba.org>
An error in merging led to 32-bit processes getting the wrong link
register value on entry to RT signal handlers, and the wrong stack
chain as well. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Newer hardware doesn't corrupt data when the queue depth
is greater than one. Rather than force the user to recompile
with a greater queue depth, make it a module parameter.
* update copyright date
* add MODULE_VERSION()
* trim trailing whitespace
* move CARM_SG_BOUNDARY to a separate enum, since its unsigned long
* bump to version 1.0
Add Kyle McMartin and Thibaut Varene as maintainers for ALSA ad1889
driver.
Add myself to CREDITS.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Missing spin_lock_init() made the Mux driver hang on SMP systems.
Fix up users of ->hpa to use ->hpa.start instead
Remove warning in 8250_gsc.c by eliminating serial_line_nr
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
.align applies to the current section - ie section directives come first.
Thanks to Joel Soete for catching this.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
fixup.S needs to specify .level and use correct LDREG macro.
New binutils has a bug where it doesn't "promote" from PA1.0 to PA1.1
correctly when using ",s" completer.
remove use of __LP64__ in assembly.h and add some white space.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Specify sr4 when flushing kernel space (we could equally well use sr5-7,
but must not use sr0).
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
replace use of "0" with "%r0" since PA 1.1 I/D flush ops only take a
general register and not an immediate value for the index field.
This just forces the code to always be PA 1.1 "clean".
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc2-pa3 fix copy_user_page_asm to NOT access past end of page.
My bad. /o\
Lamont confirmed that instructions following a conditional
branch are *alway* executed regardless if the branch is taken or not.
Unless they are nullified (which was missing in this case).
He also noted:
Conditional branches nullify on forward taken branch, and on
non-taken backward branch. Note that .+4 is a backwards branch.
This makes alot more sense than the giberish in the PA20 arch book.
Compiles and boots on both 64-bit (a500) and 32-bit (j6k).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
remove the spurious do_softirq calls from entry.S
With these in we were calling do_softirq twice; plus the calls in
entry.S took no account of nesting.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
drivers/infiniband depends on definition of pgprot_noncached() macro.
Someone else will have to fix it's wrong.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix the alloc_slabmgmt panic
Hopefully this should also fix a lot of other intermittent kernel bugs.
The problem has been around since 2.6.9-rc2-pa6 when we allowed
floating point registers to be used in kernel code. The essence of
the problem is that gcc prefers to use floating point for integer
divides and multiples. Further, it can rely on the values in the no
clobber fp regs being correct across a function call. Unfortunately,
our task switch function only saves the integer no clobber registers,
not the fp ones, so if gcc makes a function call to any function in
the kernel which could sleep, the values it is relying on in any no
clobber floating point register may be lost. In the case of
alloc_slabmgmt, the value of the page offset is being stored in %fr12
across a call to kmem_getpages(), which sleeps if no pages are
available. Thus, the offset can be trashed and the slab code can end
up with a completely bogus address leading to corruption.
Kudos to Randolph who came up with the program to trip this problem at
will and thus allowed it to be tracked and fixed.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* arch/parisc/kernel/process.c (sys_clone): Use 5 args, and process
CLONE_PARENT_SETTID, CLONE_CHILD_SETTID, CLONE_CHILD_CLEARTID.
(copy_thread): First cut at CLONE_SETTLS.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Prefix changed in debian, include "gnu" in the commandline.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Ensure the compiler version is new enough (>= 3.3)
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Document history of PDC_NARROW a bit as it will still show
up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Generate a more informative message when a resource does not have
a parent.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Get rid of some unnecessary includes
Remove a layer of macro indirection around pdc_console_device
Delete pdc_console_die() as it is unused
Avoid double-printing on panic by clearing CON_PRINTBUFFER rather than
setting con_start to be log_end
Make con_start and log_end static again
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.13-rc6-pa2
use force_sigsegv() if we have a problem setting up a frame. This is
required to prevent SIGSEGV loops.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We're using fp regs now in the kernel, so we want to print them
on stack dump
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Disable use of fpregs in pa_memcpy, and turn on the
-mdisable-fpregs flag.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
git commit 976ecd12b8 changed our locking
characteristics, and put the onus of spin_lock_init on superio.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
PA20 arch book (page 7-52 and 7-55) indicate a "sync" is required after
the FDC "to enforce instruction ordering". And we want to make
sure FIC is executed after FDC has retired.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc1-pa6 use work queue in LED/LCD driver instead of tasklet.
Main advantage is it allows use of msleep() in the led_LCD_driver to
"atomically" perform two MMIO writes (CMD, then DATA).
Lead to nice cleanup of the main led_work_func() and led_LCD_driver().
Kudos to David for being persistent.
From: David Pye <dmp@davidmpye.dyndns.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Optimize ext2_find_next_zero_bit. Gives about 25% perf improvement with a
rsync test with ext3.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
fix ext3 performance - ext2_find_next_zero() was culprit.
Kudos to jejb for pointing out the the possibility that ext2_test_bit
and ext2_find_next_zero() may in fact not be enumerating bits in
the bitmap because of endianess. Took sparc64 implementation and
adapted it to our tree. I suspect the real problem is ffz() wants
an unsigned long and was getting garbage in the top half of the
unsigned int. Not confirmed but that's what I suspect.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Fix find_next_bit for 32-bit
Make masking consistent for bitops
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Add back incorrectly removed ext2_find_first_zero_bit definition
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Fixup bitops.h to use volatile for *_bit() ops
Based on this email thread:
http://marc.theaimsgroup.com/?t=108826637900003
In a nutshell:
*_bit() want use of volatile.
__*_bit() are "relaxed" and don't use spinlock or volatile.
other minor changes:
o replaces hweight64() macro with alias to generic_hweight64() (Joel Soete)
o cleanup ext2* macros so (a) it's obvious what the XOR magic is about
and (b) one version that works for both 32/64-bit.
o replace 2 uses of CONFIG_64BIT with __LP64__. bitops.h used both.
I think header files that might go to user space should use
something userspace will know about (__LP64__).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Move SHIFT_PER_LONG to standard location for BITS_PER_LONG (asm/types.h)
and ditch the second definition of BITS_PER_LONG in bitops.h
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
update comment about CAFL_STRIDE
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fixed a bug in parisc_setup_cache_timing() which caused it to calculate
a poor value for parisc_cache_flush_threshold.
Thanks to Joel Soete for spotting the bug.
Thanks to James Bottomley for pointing out the clean way to fix this.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
o Added a control for the input source (which can be either
"line" or "mic")
o Mute the speaker/line-out/headphone outputs by default.
o Increased the buffer size from 10 pages to 16.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
ALSA Harmony was resetting the capture position when
preparing the capture substream, which it shouldn't do.
This should fix the problem.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
ALSA Harmony should no longer play junk (left in the buffers
from a previous stream) at the start of a new stream.
Implement the monitor mixer channel for ALSA Harmony.
Also prevent snd_harmony_volume_get from returning negative values.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Use the graveyard/silence buffers in ALSA Harmony.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
export profile_pc() symbol - oprofile needs it when built as a module.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Take into account nullified insn and lock functions for profiling
This is needed at the end of functions; it is typical that the return
branch nullifies the next insn, which is in the next function. This
causes profiling data to show up against the "wrong" function.
We also count lock times against the locker. This is consistent with
other architectures.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix some whitespace issues
Reorganise parisc_device probe routine to be a little less convoluted
Use ->hpa.start instead of ->hpa
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Neaten up the CONFIG_PA20 ifdefs
More merge fixes, this time for SMP
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Prettify the CONFIG_DEBUG_SPINLOCK __SPIN_LOCK_UNLOCKED initializers.
Clean up some warnings with CONFIG_DEBUG_SPINLOCK enabled.
Fix build with spinlock debugging turned on. Patch is cleaner like this,
too.
Remove mandatory 16-byte alignment requirement on PA2.0 processors by
using the ldcw,CO completer. Provides a nice insn savings.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
move pa_tlb_lock and it's primary consumers to tlb_flush.h
Future step will be to move spinlock_t definition out of system.h.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc4-pa3 : first pass at making sure use of RFI conforms to
PA 2.0 arch pages F-4 and F-5, PA 1.1 Arch page 3-19 and 3-20.
The discussion revolves around all the rules for clearing PSW Q-bit.
The hard part is meeting all the rules for "relied upon translation".
.align directive is used to guarantee the critical sequence ends more than
8 instructions (32 bytes) from the end of page.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
add || STI_CONSOLE to some of the basic FONTs. May need to get at
least one of them to default to "Y" for parisc.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix card-mode Dino crashes on 725 (and probably other Snake) systems.
Dino was coming up in fatal mode after a warm reboot. Resetting Dino
brings it out of fatal mode, so do that if the status register indicates
we're in fatal mode. Since this was never observed on any later systems,
I presume firmware does this for us on those.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Add debug statements in the cfg_read and cfg_write functions
Fix debug statements from the IRQ overhaul last winter
Rename dino_driver_callback() to dino_probe()
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 fdc/lci should be %r0 instead 0 for index (PA 1.1 compliance)
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Explain why we need insert_resource() instead of request_resource().
Fundementally, this is more convoluted for ccio driver because of
o legacy (HP-PB) transperant bridges.
o support for MMIO behind card-mode Dino (PCI)
o support for above bridges without ccio in the box
SBA driver doesn't have to worry about those issues.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Use insert_resource instead of request_resource now that the subdevices
will already have their resources claimed
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
re-enable use of "inline" for perf critical functions.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa5 fix sign extension of MMIO range
Fixes the problem of claiming a range that is disabled on 64-bit kernel:
ccio_init_resource() claimed CCIO bus address space (ffffffff00000000,
ffffffffffffffff)
also removes use of __FILE__.
Tested on both 32 and 64-bit systems by Joel.
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc1-pa7 incorrect BUG_ON in ccio
ccio-dma.c line 1317 was preventing K-class with 4GB RAM from booting.
Any ccio machine with >=2GB of RAM would have (incorrectly) triggered this.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Convert to ioremap and __raw_read/write
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
revert use of %%sr0 in fdc asm.
Thanks to Joel Soete for pointing out this oversight.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa3 move "sync" outside the main loop that fills IO Pdir.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove explicit use of sr0 in fdc ops.
Thanks to Joel Soete for reminding me were I added those...
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.14-rc2-pa2 - make SBA more anal about invalidating pdir entries
Previous code cleared the valid flag a pdir entry but it did NOT
guarantee this change was visible to the PDIR before writing
the PCOM register. Ie the SBA could pick up a stale entry if
the write happened to hit the SBA before the cacheline was flushed
from the cache.
Long term, I think I want to make this a compile time flag.
Developement tree should enable anal pdir checking by default
and Debian can disable it with either a CONFIG option
or one-line patch. fdc/sync options can only negatively affect
performance though I haven't measure how much yet.
If someone can run netperf TCP_RR across gige and compare
-pa1 and -pa2, that would be sufficient.
Cleaned up the use of "fdc" to make sure it's using "kernel"
space id (specify sr0 but maps to sr4-7). It seems a bit fragile
to assume "sr1" gets loaded with KERNEL_SPACE which is how the
code works today.
Tested on 32 and 64-bit SMP kernels on j6k.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
remove PDC_NARROW from SBA and document history of PDC_NARROW a bit.
It will still show up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
if/ifdef cleanups from Joel Soete.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
2.6.12-rc4-pa2 fix 32-bit support for Astro platforms
o Since my last SBA code change, SBA could allocate more than 1GB of IOVA
space on Astro boxes with more than 1GB of RAM when running 32-bit kernel.
This is bad since IOMMU can only talk to the first 1GB at most.
Kudos to jejb for quickly spotting that bug.
o jejb also noted SBA should *always* reject DMA masks > 32-bits since
DMA-mapping.txt indicates caller should try again with 32-bits.
o off-by-one error when comparing the mask to IOVA space size.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When I originally moved exit_itimers into __exit_signal, that was the only
place where we could reliably know it was the last thread in the group
dying, without races. Since then we've gotten the signal_struct.live
counter, and do_exit can reliably do group-wide cleanup work.
This patch moves the call to do_exit, where it's made without locks. This
avoids the deadlock issues that the old __exit_signal code's comment talks
about, and the one that Oleg found recently with process CPU timers.
[ This replaces e03d13e985, which is why
it was just reverted. ]
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a stupid typo bug in the iSeries hash table code.
When we place a hash PTE in the secondary bucket, instead of setting the
SECONDARY flag bit, as we should, we (redundantly) set the VALID flag.
This was introduced with the patch abolishing bitfields from the hash
table code. Mea culpa, oops. It hasn't been noticed until now because
in practice we don't hit the secondary bucket terribly often.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wrong state emission routines were being called for G550, and
consistent maps weren't correctly mapped...
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While working on 64K pages, I found this little buglet in our
update_mmu_cache() implementation.
The code calls __hash_page() passing it an "access" parameter (the type
of access that triggers the hash) containing the bits _PAGE_RW and
_PAGE_USER of the linux PTE. The latter is useless in this case and the
former is wrong. In fact, if we have a writeable PTE and we pass
_PAGE_RW to hash_page(), it will set _PAGE_DIRTY (since we track dirty
that way, by hash faulting !dirty) which is not what we want.
In fact, the correct fix is to always pass 0. That means that only
read-only or already dirty read write PTEs will be preloaded. The
(hopefully rare) case of a non dirty read write PTE can't be preloaded
this way, it will have to fault in hash_page on the actual access.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a typo in the div128_by_32 function used in the timekeeping
calculations on ppc64. If you look at the code it's quite obvious
that we need (rb + c) rather than (rb + b). The "b" is clearly just a
typo.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes handling of the phy identifiers in mptsas.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
[ split it a pre-2.6.14 portion from Eric's bigger patch ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Use GFP mask on TX skb allocation.
* Use the tx_headroom and reserve requested space.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The merge of syscalls.c & sys_ppc32.c (30286ef6e0)
broke mmap, if the mmap returned a 64 bit address.
do_mmap2 was taking the return value from do_mmap_pgoff (an unsigned long), and
storing it in an int, before returning it to sys_mmap as an unsigned long. So
we were losing the high bits of the address.
You would have thought the compiler could catch this for us ...
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch to make process.c work for 32-bit and 64-bit
(06d67d5474) broke some 64-bit binaries.
We were blowing away load_addr in gpr[2], so we weren't properly relocating
the entry point.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the merge tree, commit 0458060c1c
broke boot on some machines because the initialization of conswitchp
was moved to arch/powerpc/kernel/setup_64.c, but a corresponding copy
was not added to arch/ppc64/kernel/setup.c. This patch fixes it.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sata_qstor strays into a nasty area - gcc handling of wide enums is
full of bugs that got fixed between gcc versions creating portability
nightmare. Single-member enums are safe, so are ones that stay within
the range of int or unsigned int. Anything beyond that is asking for
trouble.
Declaration of constants split in two enums, taking the ~0UL one into
a separate enum.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Ben Dooks
The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Avoid the possiblity that if the board is using
a 16.9334 or higher crystal with a high PLL
multiplier, then the pll value could overflow
the capability of an int.
Also fix the value types of the intermediate
variables to unsigned int.
Rewrite of patch from Guillaume Gourat
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
need to get in ahead of it that depend on that file handle. Fixes
occassional bad file handle errors on write with heavy use multiple process
cases.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Improve sb1250-mac driver to probe for PHYs at addresses other
than 1, such as the PHYs on BigSur.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff found an endian bug in the Marvell driver (thanks!). Here's the
fix for it.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add missing "break" in switch statement. Without the break, the
CM ended up always falling through and setting every connection
request to use RC transport, which meant that UC connections
didn't work.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It is legitimate to call tcp_fragment with len == skb->len since
that is done for FIN packets and the FIN flag counts as one byte.
So we should only check for the len > skb->len case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
changes to swiotlb.c made in commit 281dd25cdc
since this file has been moved from arch/ia64/lib/swiotlb.c to
lib/swiotlb.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turns out the problem has nothing to do with use-after-free or double-free.
It's just that we're not clearing the CB area and DCCP unlike TCP uses a CB
format that's incompatible with IP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
icmp_send doesn't use skb->sk at all so even if skb->sk has already
been freed it can't cause crash there (it would've crashed somewhere
else first, e.g., ip_queue_xmit).
I found a double-free on an skb that could explain this though.
dccp_sendmsg and dccp_write_xmit are a little confused as to what
should free the packet when something goes wrong. Sometimes they
both go for the ball and end up in each other's way.
This patch makes dccp_write_xmit always free the packet no matter
what. This makes sense since dccp_transmit_skb which in turn comes
from the fact that ip_queue_xmit always frees the packet.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
David S. Miller <davem@davemloft.net> wrote:
> One thing you can probably do for this bug is to mark data packets
> explicitly somehow, perhaps in the SKB control block DCCP already
> uses for other data. Put some boolean in there, set it true for
> data packets. Then change the test in dccp_transmit_skb() as
> appropriate to test the boolean flag instead of "skb_cloned(skb)".
I agree. In fact we already have that flag, it's called skb->sk.
So here is patch to test that instead of skb_cloned().
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Without this patch, if you try and use a key that has not been
configured, for example:
% iwconfig eth1 key deadbeef00 [2]
without having configured key [1], then the active key will still be
[1], but privacy will now be enabled. Transmission of a packet in this
situation will result in a kernel oops.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This reverts commit 3359b54c8c and
replaces it with a cleaner version that is purely based on page table
operations, so that the synchronization between inode size and hugetlb
mappings becomes moot.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver version, white space, comments, device id & other
Originally posted on 8/31 (and perhaps before)...I think it has not
been committed because the patch from that posting was damaged. I'm
reposting to make sure it gets in... :-)
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Include MII address 0 at the end of the PHY scan. This covers the
entire range of possible MII addresses.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I had the sense of the test for when to use the old 601-style RTC
registers inverted. pmac_calibrate_decr and via_calibrate_decr
weren't setting ppc_tb_freq, on which all the further calculations
depended. Lastly, update_gtod was losing the top 32 bits of
the new tb_to_xs value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously the individual xxx_calibrate_decr functions would each
print the timebase and cpu frequency and calculate several values
such as tb_to_us and tb_to_xs. This moves those printks and
calculations into time_init just after the call to the platform's
calibrate_decr function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This way they get done in one place for all platforms, and it is
more consistent with what ppc32 does.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Except for smu.h, which moved from asm-ppc64 to asm-powerpc, all
of these moved from asm-ppc to asm-powerpc. In each case the
asm-ppc64 version (if there was one) was just a single line
including the asm-ppc version.
Signed-off-by: Paul Mackerras <paulus@samba.org>
I missed a few places where ppc code was still assuming that the
ppc_md.show_[per]cpuinfo functions returned int.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having it here rather than in arch/ppc64/kernel/smp.c means that
we can use it on 32-bit SMP systems easily with ARCH=powerpc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges types.h into include/asm-powerpc. The only real change is
the removal of the include of linux/config.h from the 32-bit version - it
doesn't appear to be necessary.
This patch has been built on several different 32 and 64-bit platforms,
and booted on mpc8540_ads.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The _GLOBAL() macro is for text symbols only. Changed to using
.globl for .data symbols. This is also needed in ppc32 land
to allow FSL Book-E, 40x, and 44x to work.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some minor fixes that are needed if we are building for a book-e
processor.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code was incorrectly doing a division by 0 in the case where
the denominator was 0x100000000 and the divisor was 0xffffffff.
Thanks to Fred Liu of Motorola for pointing this out.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We now use the merged time.c for both 32-bit and 64-bit compilation
with ARCH=powerpc, and for ARCH=ppc64, but not for ARCH=ppc32.
This removes setup_default_decr (folds its function into time_init)
and moves wakeup_decrementer into time.c. This also makes an
asm-powerpc/rtc.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines CONFIG_PPC_STD_MMU for ppc64, changes an instance of
sys32_ to compat_sys_ in the ppc64 syscall table, and removes a
reference to a non-existent arch/powerpc/xmon/Makefile.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A few things change for consistency between ppc32 and ppc64:
idle functions return void; *_get_boot_time functions return
unsigned long (i.e. time_t) rather than filling in a struct rtc_time
(since that's useful to the callers and easier for pmac to
generate); *_get_rtc_time and *_set_rtc_time functions take
a struct rtc_time; irq_canonicalize is gone; nvram_sync returns
void.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes platform code use the smp_ops variable directly instead
of ppc_md.smp_ops, removes the two unused `data' and `wait' arguments
from the *_message_pass() functions, and removes the call to the
never-implemented smp_ops->space_timers() function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many thanks to Alberto Patino for testing and reporting the data
corruption. And many apologies for corrupting his partition.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Not only are the qop parameters that are passed around throughout the gssapi
unused by any currently implemented mechanism, but there appears to be some
doubt as to whether they will ever be used. Let's just kill them off for now.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The code this was originally derived from processed wrap and mic tokens using
the same functions. This required some contortions, and more would be required
with the addition of xdr_buf's, so it's better to separate out the two code
paths.
In preparation for adding privacy support, remove the last vestiges of the
old wrap token code.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add the code to the client side to handle privacy. This is dead code until
we actually add privacy support to krb5.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Various xdr encode routines use au_rslack to guess where the reply argument
will end up, so we can set up the xdr_buf to recieve data into the right place
for zero copy.
Currently we calculate the au_rslack estimate when we check the verifier.
Normally this only depends on the verifier size. In the integrity case we add
a few bytes to allow for a length and sequence number.
It's a bit simpler to calculate only the verifier size when we check the
verifier, and delay the full calculation till we unwrap.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For privacy we need to allocate extra pages to hold encrypted page data when
wrapping requests. This allocation may fail, and we handle that case by
waiting and retrying.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For privacy, we need to allocate pages to store the encrypted data (passed
in pages can't be used without the risk of corrupting data in the page cache).
So we need a way to free that memory after the request has been transmitted.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for privacy to generic gss-api code. This is dead code until we
have both a mechanism that supports privacy and code in the client or server
that uses it.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
resp_len is passed in as buffer size to decode routine; make sure it's
set right in case where userspace provides less than a page's worth of
buffer.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Stop handing garbage to userspace in the case where a weird server clears the
acl bit in the getattr return (despite the fact that they've already claimed
acl support.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch stops the release_pipe() funtion from being called
twice by invalidating the ops pointer in the rpc_inode
when rpc_pipe_release() is called.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Storing a pointer to the struct rpc_task in the nfs_seqid is broken
since the nfs_seqid may be freed well after the task has been destroyed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Expand the mask used when reseting the chip to include the GlobalReset
bit. This fix comes from ICPlus and seems to be required for some
cards.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove an if (1) { ... } block in sundance_probe1. Its purpose seems
to be only to allow for delaring some extra local variables. But, it also
adds ugly indentation without adding any meaning to the code.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Checking the skb->len value before calling skb_padto is redundant.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is a (final?) hack to support the odd DMA allocation requirements
of the b44 hardware. The b44 hardware has a 30-bit DMA mask. On x86,
anything less than a 32-bit DMA mask forces allocations into the 16MB
GFP_DMA range. The memory there is somewhat limited, often resulting
in an inability to initialize the b44 driver.
This hack uses streaming DMA allocation APIs in order to provide an
alternative in case the GFP_DMA allocation fails. It is somewhat ugly,
but not much worse than the similar existing hacks to support SKB
allocations in the same driver. FWIW, I have received positive
feedback on this from several Fedora users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Expand comment explaining MAC address selection for replicated IGMP
frames transmitted in bonding mode 1 (active-backup). Also, a small
whitespace cleanup.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add "HasHltClk" flag for RTL-8100B/8139D hardware in order to fix
problems resuming from suspend-to-RAM.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix some simple typos in the bonding.txt file. The typos are in areas
relating to loading the bonding driver multiple times.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
work_done is overwritten each time through the rx_action loop in
epic_poll. This screws-up the NAPI accounting if the loop is executed
more than once.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Get rid of the mdelay call in rhine_disable_linkmon. The function
is called from the via-rhine versions of mdio_read and mdio_write.
Those functions are indirectly called from rhine_check_media and
rhine_tx_timeout, both of which can be called in interrupt context.
So, create tx_timeout_task and check_media_task as instances of struct
work_struct inside of rhine_private. Then, change rhine_tx_timeout to
invoke schedule_work for tx_timeout_task (i.e. rhine_tx_timeout_task),
moving the work to process context. Also, change rhine_error (invoked
from rhine_interrupt) to invoke schedule_work for check_media_task
(i.e. rhine_check_media_task), which simply calls rhine_check media
in process context. Finally, add a call to flush_scheduled_work in
rhine_close to avoid any resource conflicts with pending work items.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/e1000/e1000_main.c: In function `e1000_intr':
drivers/net/e1000/e1000_main.c:3156: error: `i' undeclared (first use in this function)
drivers/net/e1000/e1000_main.c:3156: error: (Each undeclared identifier is reported only once
drivers/net/e1000/e1000_main.c:3156: error: for each function it appears in.)
This function is foul.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/declance.c | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
o Add support for DP83847 MII.
o remove unused variable.
o Add some initialisations so even an unknown MII won't result in a crash.
o Correct error message to "no known MIIs found".
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/au1000_eth.c | 13 +++++--------
1 files changed, 5 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Avoid entering a QP as member of a multicast group multiple times.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If someone tries to rename a directory onto an empty directory, we
currently fail and return EBUSY.
This patch ensures that we try the rename if both source and target
are directories, and that we fail with a correct error of EISDIR if
the source is not a directory.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We currently fail Connectathon test 6.10 in the case of 32-bit locks due
to incorrect error checking.
Also add support for l->l_len < 0 to 64-bit locks.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the server is in the unconfirmed OPEN state for a given open owner
and receives a second OPEN for the same open owner, it will cancel the
state of the first request and set up an OPEN_CONFIRM for the second.
This can cause a race that is discussed in rfc3530 on page 181.
The following patch allows the client to recover by retrying the
original open request.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This will allow nfs_permission() to perform additional optimizations when
walking the path, by folding the ACCESS(MAY_EXEC) call on the directory
into the lookup revalidation.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Make NFSv4 return the fully initialized file pointer with the
stateid that it created in the lookup w/intent.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is needed by NFSv4 for atomicity reasons: our open command is in
fact a lookup+open, so we need to be able to propagate open context
information from lookup() into the resulting struct file's
private_data field.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We no longer need to worry about collisions between close() and the state
recovery code, since the new close will automatically recheck the
file state once it is done waiting on its sequence slot.
Ditto for the nfs4_proc_locku() procedure.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Once the state_owner and lock_owner semaphores get removed, it will be
possible for other OPEN requests to reopen the same file if they have
lower sequence ids than our CLOSE call.
This patch ensures that we recheck the file state once
nfs_wait_on_sequence() has completed waiting.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFSv4 file state-changing functions such as OPEN, CLOSE, LOCK,... are all
labelled with "sequence identifiers" in order to prevent the server from
reordering RPC requests, as this could cause its file state to
become out of sync with the client.
Currently the NFS client code enforces this ordering locally using
semaphores to restrict access to structures until the RPC call is done.
This, of course, only works with synchronous RPC calls, since the
user process must first grab the semaphore.
By dropping semaphores, and instead teaching the RPC engine to hold
the RPC calls until they are ready to be sent, we can extend this
process to work nicely with asynchronous RPC calls too.
This patch adds a new list called "rpc_sequence" that defines the order
of the RPC calls to be sent. We add one such list for each state_owner.
When an RPC call is ready to be sent, it checks if it is top of the
rpc_sequence list. If so, it proceeds. If not, it goes back to sleep,
and loops until it hits top of the list.
Once the RPC call has completed, it can then bump the sequence id counter,
and remove itself from the rpc_sequence list, and then wake up the next
sleeper.
Note that the state_owner sequence ids and lock_owner sequence ids are
all indexed to the same rpc_sequence list, so OPEN, LOCK,... requests
are all ordered w.r.t. each other.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, call_encode will cause the entire RPC call to abort if it returns
an error. This is unnecessarily rigid, and gets in the way of attempts
to allow the NFSv4 layer to order RPC calls that carry sequence ids.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
After a server crash/reboot, rebinding should always retry, otherwise
requests on "hard" mounts will fail when they shouldn't.
Test plan:
Run a lock-intensive workload against a server while rebooting the server
repeatedly.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
problem:
id[53-58] might be changed after initializing device CHS settings.
changes:
- call ata_dev_reread_id() to reread the identify device info,
after initializing device CHS settings.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We keep IB device structures around until the last sysfs reference is
gone, but we shouldn't ask the low-level driver to do anything after
the LLD unregisters the device. To handle this, check the reg_state
field and just fail sysfs show() requests if the device has already
been unregistered.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If .owner isn't set the module can be unloaded even while still active.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SMACK (Stuttgart Modified Amateurradio CRC KISS) is a KISS variant that
uses CRC16 checksums to secure data transfers between the modem and host.
It's also used to communicate over a pty to applications such as Wampes.
Patches for Linux 2.4 by Thomas Osterried DL9SAU, upgraded to the latest
mkiss 2.6 mkiss driver by me.
Signed-off-by: Thomas Osterried DL9SAU <thomas@x-berg.in-berlin.de>
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From Suzanne Wood <suzannew@cs.pdx.edu>:
Clarify RCU implementation in bpqether.c.
Because bpq_new_device() calls list_add_rcu() and bpq_free_device() calls
list_del_rcu(), substitute list_for_each_entry_rcu() for
list_for_each_entry() in bpq_get_ax25_dev() and in bpq_seq_start().
Add rcu dereference protection in bpq_seq_next().
The rcu_read_lock()/unlock() in bpq_device_event() are removed because
netdev event handlers are called with RTNL locking in place.
FYI: bpq_free_device() calls list_del_rcu() which, per list.h, requires
synchronize_rcu() which can block or call_rcu() or call_rcu_bh() which
cannot block. Herbert Xu notes that synchronization is done here by
unregister_netdevice(). This calls synchronize_net() which in turn uses
synchronize_rcu().
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes the following bugs with offline diagnostics
code(run with "ethtool -t").
1. After running offline diagnostics, adapter would report
corrupted packets on receive. This was because of adapter not
being brought out of "RLDRAM test mode".
2. Current EEPROM test works only for Xframe I. Since Xframe II
uses different interface(SPI), support for this interface has
been added. Also, since SPI supports write access to all areas
of EEPROM, negative testing is done only for Xframe I.
3. Return values from subfunctions of offline diagnostics have
been corrected.
4. In register test, expected value from rx_queue_cfg register
is made to depend on adapter type.
5. After the test, need to restore values at EEPROM offsets
0x4F0 and 0x7F0. These locations were modified as part of test.
6. Use macro SPECIAL_REG_WRITE for write access to mc_rldram_test_ctrl
register. Also, couple of unnecessary writes to mc_rldram_test_ctrl
have been removed.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make the type parameter of mthca_alloc_db() be an enum mthca_db_type
instead of an int. This doesn't have any practical effect but
documents the functions a little better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use jiffies_to_msecs() so we print a human-readable time so
we don't have to worry about what HZ is configured to, and
print out a few values to make post-mortem analysis easier.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows us to get rid of one type of entry in systbl.S.
In passing we remove the duplicate compat_sys_getdents and
compat_sys_utimes for which there are generic versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This makes ppc use the syscalls.c from arch/powerpc/kernel, exports
copy_and_flush from head_32.S for use by prom_init.c (ARCH=powerpc),
and consolidates the sys_fadvise64_64 implementations for 32-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Bind communication identifiers to a device to support device removal.
Export per HCA CM devices to userspace.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Add kernel support for userspace calling poll CQ, request CQ
notification, post send, post receive, post SRQ receive, create AH and
destroy AH commands. These commands allow us to support userspace
verbs for devices that can't perform these operations directly from
userspace (eg the PathScale HCA).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add kernel/user ABI structures for marshalling poll CQ, request CQ
notification, post send, post receive, post SRQ receive, create AH and
destroy AH commands. These commands allow us to support userspace
verbs for devices that can't perform these operations directly from
userspace (eg the PathScale HCA).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Give each device a uverbs_cmd_mask, so that a low-level driver can
control which methods may be called on behalf of userspace.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the SA query module's initialization fails for a device, then that
device won't have a struct ib_sa_device associated. We should fail SA
queries in that case, rather than blindly dereferencing the NULL
pointer we get back from ib_get_client_data().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_create_qp() no longer creates IPoIB's QP, so it shouldn't
destroy the QP on failure -- that unwinding happens elsewhere, so the
current code can cause a double free. While we're at it, the
function's name should match what it actually does, so rename it to
ipoib_init_qp().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check the sizes of CQs, QPs and SRQs when creating objects, and fail
instead of creating too-big queues. Also return real limits instead
of just plausible-sounding values from mthca_query_device().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a bug in ib_mad_init_device(): if ib_agent_port_open() fails
for a given port, then the current code doesn't call ib_mad_port_close()
for that port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware relies on us keeping one extra work request that never
gets used in SRQs. Add checks to the SRQ work request posting
functions so that they fail when someone is about to use up that extra
work request, rather than when someone uses the very last work request.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Our hardware supports generating an event when the number of receives
posted to a shared receive queue (SRQ) falls below a user-specified
limit. Implement mthca_modify_srq() to arm the limit, and add code to
handle dispatching SRQ events when they occur.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reject userspace memory registrations with invalid permission flags:
"local write" is required if "remote write" or "remote atomic" is also
requested.
Pointed out by Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add code to fill in the bad_pkey_cntr, max_mtu, active_mtu and
subnet_timeout fields in mthca_query_port().
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add abi_version attribute to uverbs class devices to allow for
ABI versioning of device-specific interfaces.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
By waiting to add resources to our lists until after the last
operation that can fail, we don't have to remove them from their lists
in the error path. Also, we should hold the idr mutex until we know
whether resource creation has succeed or failed, to avoid someone
finding a resource in our table before we're ready.
Loosely based on work by Robert Walsh <rjwalsh@pathscale.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Introduce new userspace verbs ABI version 3. This eliminates some
unneeded commands, and adds support for user-created completion
channels. This cleans up problems with file leaks on error paths, and
also makes sure that file descriptors are always installed into the
correct process.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return correct atomic capability flag from mthca query function.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add checks so that we only allow multicast attach/detach with
a valid multicast GID and the correct QP type.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch from Eric fixes handling of the phy identifiers in mptsas.
I've split it up from his bigger patch as it should go into 2.6.14
still.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below should make the Pioneer DRM-624X automatically
be set up with all 6 "drives". (6 slot SCSI CD changer)
Signed-off-by: Karl Magnus Kolst <karl.kolsto@uib.no>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ARCH=powerpc, a spurious ifdef in prom_init prevented the
seconday hold loop being correctly copied down on Maple. With this
patch, Maple boots with ARCH=powerpc
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merge-tree version of LOADBASE actually loads the whole given
address from the toc for ppc64. The matching OFF macro adjust for
this, using an offset of 0 for ppc64, but we weren't using that in
power4_idle.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The _GLOBAL() macro is for text symbols only. Changed to using
.globl for .data symbols.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were initializing the btext stuff from prom_init(), thus breaking
the rule that all communication between prom_init() and the rest of
the kernel has to be via the flattened device tree. This removes
the btext initialization calls from prom_init() and initializes it
instead after the device tree is unflattened. It would be nice to
do it earlier, but that needs some more infrastructure to find the
properties we need in the flattened device tree.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a request is deferred in scsi_init_io because the sg table could not
be allocated, the associated scsi_cmnd is not released and the request is
not marked with REQ_DONTPREP. When the command is retried, if
scsi_prep_fn decides to kill it then the scsi_cmnd will never be released.
This patch (as573) changes scsi_init_io so that it calls scsi_put_command
before deferring a request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Juan was kind enough to linger on site, and work on a production
machine, to try the parameter to make the system stable. He discovered
that reducing the maximum transfer size issued to the adapter to 128KB
stabilized his system. This is related to an earlier change for the
2.6.13 tree resulting from Martin Drab's testing where the transfer size
was reduced from 4G to 256KB; we needed to go still further in scaling
back the request size.
Here is the patch that tames this regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix 12 undefined preprocessor identifier warnings (4 each in 3 driver builds):
drivers/scsi/NCR5380.c:2744:16: warning: undefined preprocessor identifier 'NDEBUG_ABORT'
drivers/scsi/NCR5380.c:2744:16: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The only real user of this file outside platforms/iseries was
drivers/net/iseries_veth.c but all it wanted was ISERIES_HV_ADDR()
so we move that to abs_addr.h (and lowercase it).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This removes three headers from include/asm-ppc64 that are now in
include/asm-powerpc and are sufficiently similar that they can be
used with ARCH=ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Recent commits upstream have changed files which are currently
duplicated in arch/powerpc and include/asm-powerpc. This updates
them with the corresponding changes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We weren't computing the size of the hash table correctly on iSeries
because the relevant code in prom.c was #ifdef CONFIG_PPC_PSERIES.
This moves the code to hash_utils_64.c, makes it unconditional, and
cleans it up a bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
New cifs_writepages routine was not updated bytes written in cifs stats.
Also added ability to clear /proc/fs/cifs/Stats by writing (0 or 1) to it.
Signed-off-by: Steve French <sfrench@us.ibm.com>
On ARCH=ppc64 we were getting htab_hash_mask recalculated
to the correct value for our particular machine by accident.
In the merge tree, that code was commented out, so htab_hash_mask
was being corrupted.
We now set ppc64_pft_size instead which gets htab_has_mask
calculated correctly for us later. We should put an
ibm,pft-size property in the device tree at some point.
Also set -mno-minimal-toc in some makefiles.
Allow iSeries to configure PROC_DEVICETREE.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
file operations ->write(), ->aio_write(), and ->writev() for regular
files. This replaces the old use of generic_file_write(), et al and
the address space operations ->prepare_write and ->commit_write.
This means that both sparse and non-sparse (unencrypted and
uncompressed) files can now be extended using the normal write(2)
code path. There are two limitations at present and these are that
we never create sparse files and that we only have limited support
for highly fragmented files, i.e. ones whose data attribute is split
across multiple extents. When such a case is encountered,
EOPNOTSUPP is returned.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
and cond_resched() in the main loop as we could be dirtying a lot of
pages and this ensures we play nice with the VM and the system as a
whole.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
This used to be inline in include/asm-ppc64/unistd.h, but isn't
inline in the merged include/asm-powerpc/unistd.h, so we need a
definition here.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.
This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now instead of having a ppc_md function, we just have a variable
which says whether to do the i8259 irq canonicalization or not,
and set that variable on the platforms that need that. It looks
to me that radstone_ppc7d was trying to use irq canonicalization
for something else in a broken kind of way - it will need to be
fixed properly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bunch of printks were left in arch/powerpc/kernel/setup_64.c from
when I was chasing a bug. This removes them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
At the moment we don't have a merged arch/powerpc/boot, so we build the
boot images in arch/ppc/boot and arch/ppc64/boot. Unfortunately the
makefile targets are different in those two directories, so this makes
a change to accommodate both for the moment.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This was preventing us from recognizing that we did actually
instantiate RTAS successfully on pSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the Device_List member from struct device_node to
struct pci_dn, which cleans up the device_node and makes the code
a little simpler.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a bunch of mostly small fixes that are needed to get
ARCH=powerpc to compile for 64-bit. This adds setup_64.c from
arch/ppc64/kernel/setup.c and locks.c from arch/ppc64/lib/locks.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since lparmap.s gets included in arch/powerpc/kernel/head_64.S,
this avoids depending on a file in another directory.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Although both ppc32 and ppc64 have a reloc_offset function, the ppc64
one produced the opposite sign to the ppc32 one. This standardizes
on the ppc32 sign and fixes the merged 64-bit code to account for that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The system call table has been consolidated into systbl.S. We have
separate 32-bit and 64-bit versions of entry.S and misc.S since the
code is mostly sufficiently different to be not worth merging.
There are some common bits that will be extracted in future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also puts a copy of indirect_pci.c in arch/powerpc/sysdev
so that we don't need to build in arch/ppc/syslib.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that the register names and bit definitions are all in reg.h,
use that instead of processor.h in assembly code in a few places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the files are now in arch/powerpc/platforms/powermac, the
pmac_ prefix that they had is redundant.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the remaining files in arch/ppc64/mm to arch/powerpc/mm,
and arranges that we use them when compiling with ARCH=ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This doesn't change any code, just renames things so we consistently
have foo_32.c and foo_64.c where we have separate 32- and 64-bit
versions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only real change here is that lmb_enforce_memory_limit now takes
the memory_limit as a parameter instead of as a global variable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds register definitions from the ppc64 processor.h to reg.h,
and makes a single merged processor.h. I moved __is_processor from
the ppc64 system.h to the merged reg.h along with the PVR register
constants.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes symbols like HID0, SPRG3, SRR0, SRR1 etc. that refer to
special purpose registers to SPRN_HID0, SPRN_SPRG3, etc. Using the
SPRN_ symbols clutters the namespace less, and the forthcoming merge
of asm/processor.h and asm/reg.h is going to remove the non-SPRN_
versions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for sil_3131 and sil_3531. Both are
identical to 3124 except that they have only one port. Bits 30 and 31
of ata_port_info->host_flags is used to encode available port numbers.
Version number is bumped to 0.22.
Edward Falk supplied all the necessary information and preliminary
patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
- change "xlat" and "fill" actors in libata-scsi so
they are responsible for SCSI status and sense data
when they return 1. This allows GOOD status or a
specialized error to be set.
- yield an error for mode sense requests for saved
values [sat-r06]
- remove static inlines for ata_bad_scsiop() and
ata_bad_cdb() which are no longer used
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add extern ata_scsi_set_sense() to build SCSI
fixed sense data and corresponding SCSI status
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These changes to debug code and new stats are helpful in
debugging potential tcp performance/configuration problems under cifs.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Hello, guys.
This patch implements ->tf_read callback for sil24. It didn't use to
be necessary but new ata_gen_fixed_sense now makes use of ->tf_read
callback. This patch is taken from Edward Falk's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
03_sil24_add-tf-reading.patch
This patch implements proper TF register reading back and
caching and bumps up version to 0.22. This is taken from
Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 50 +++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 45 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
01_sil24_ignore-non-error-exception-irqs.patch
Do not error-finish commands for non-error exception irqs -
just ignore them. This is taken from Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These days there is no good reason to run a ppc32 kernel on a 64-bit
cpu, rather than a ppc64 kernel, so remove the config option and a
bunch of code (and ifdefs) from head.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also creates merged versions of do_init_bootmem, paging_init
and mem_init and moves them to arch/powerpc/mm/mem.c. It gets rid
of the mem_pieces stuff.
I made memory_limit a parameter to lmb_enforce_memory_limit rather
than a global referenced by that function. This will require some
small changes to ppc64 if we want to continue building ARCH=ppc64
using the merged lmb.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in the ppc64 version of prom_init.c, prom.c and btext.c
and makes them work for ppc32. This also brings in the new calling
convention, where the first entry to the kernel (with r5 != 0) goes
to the prom_init code, which then restarts from the beginning (with
r5 == 0) after it has done its stuff.
For now this also brings in the ppc32 version of setup.c. It also
merges lmb.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These macros help in writing assembly code that works for both ppc32
and ppc64. With this we now have a common fpu.S. This takes out
load_up_fpu from head_64.S.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows cifs_writepages to send data in larger chunks from the page
cache, without requiring larger memory allocations in other cases.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This should fix up lockups that people were seeing due to
improper spinlock placement. Also, the start/stop DMA routines put
guarded trust in the cached state of DMA.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) note urgent bug, that completes command twice
2) only fix up INQUIRY data if the SCSI version is zero (typically
indicates ATAPI MMC-ish device)
3) if there is a problem on the ATA bus, don't bother with REQUEST
SENSE, just directly handle the error based on Status/Error registers.
gensparse_defconfig is a config generated file for SPARSEMEM and GENERIC
kernel configuration (defconfig).
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is the minimal set of changes required by ia64 to use SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch introduces the conditional changes required for the three
memory models. With [patch 1/4] there are three memory models; FLATMEM,
DISCONTIG and SPARSEMEM. Also a new arch include file sparemem.h is
introduced for defining SPARSEMEM parameters.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
For FLATMEM contig_page_data has been made transparent to the arch code.
This patch conforms to that change.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch modifies the Kconfig file to introduce the new memory model
options and other related SPARSEMEM changes. There is also a minor change
in the Makefile.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove all references to the bist_lock in the SN code as it
is not used for anything.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
the initial implementation of file truncation. Now both open(2)ing
a file with the O_TRUNC flag and the {,f}truncate(2) system calls
will resize a file appropriately. The limitations are that only
uncompressed and unencrypted files are supported. Also, there is
only very limited support for highly fragmented files (the ones whose
$DATA attribute is split into multiple attribute extents).
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
extend the allocation of an attributes. Optionally, the data size,
but not the initialized size can be extended, too.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
which is zero for a resident attribute but should no longer be zero
once the attribute is non-resident as it then has real clusters
allocated.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
as an extra parameter. This is needed since we need to know the size
before we can map the mft record and our callers always know it. The
reason we cannot simply read the size from the vfs inode i_size is
that this is not necessarily uptodate. This happens when
ntfs_attr_make_non_resident() is called in the ->truncate call path.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
specifying whether the cluster are being allocated to extend an
attribute or to fill a hole.
- Change ntfs_attr_make_non_resident() to call ntfs_cluster_alloc()
with @is_extension set to TRUE and remove the runlist terminator
fixup code as this is now done by ntfs_cluster_alloc().
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
search context as argument. This allows calling it with the mft
record mapped. Update all callers.
- Fix potential deadlock in ntfs_mft_data_extend_allocation_nolock()
error handling by passing in the active search context when calling
ntfs_cluster_free().
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
search context as argument. This allows calling it with the mft
record mapped. Update all callers.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
Replicate IGMP frames across all slaves in activebackup mode. This
ensures fail-over is rapid for multicast traffic as well. Otherwise,
multicast traffic will be lost until the next IGMP membership report
poll timeout.
This is conceptually similar to the treatment of IGMP traffic in
bond_alb_xmit. In that case, IGMP traffic transmitted on any slave
is re-routed to the active slave in order to ensure that multicast
traffic continues to be directed to the active receiver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use the size of the target array for the length argument to strncpy
instead of the size of the source or a magic number.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cisco Aironet doesn't resume properly from swsusp, because the resume
method confuses a PM_EVENT_* for a PCI power state. It thinks that it is
resuming from PCI_D1 and doesn't do the necessary initialization of the
card.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Fixes for packet split related issues
* On platforms where PAGE_SIZE > 4K, driver will use only required number of
pages compared to always using 3 pages.
* Packet split won't be used if the PAGE_SIZE is > 16K
* Adds a statistics counter to splits.
* Setting the non Null ptr to zero sized buffers to solve packet split
receive descriptor error
* When the no of pages needed is calculated, the header buffer is not
included for a given MTU.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for MSI/MSI-X feature to the driver. It is
a runtime parameter(for now, loadable parameter). Default is INTA.
Patch has been tested on IA64 platform with Xframe II adapter,
both of which support MSI-X feature. An improvement of about 7%
in throughput(both Tx and Rx) was observed and a reduction by 7%
in CPU utilization during Tx test.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hello, Jeff.
This patch adds ATA errors & exceptions chapter to
Documentation/DocBook/libata.tmpl. As suggested, the chapter is
placed before low level driver specific chapters. Contents are
unchanged from the last posting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is my libata compatible low level driver for the Marvell SATA
family. Currently it runs in DMA mode on a 6081 chip.
The 5xxx series parts are not yet DMA capable in this driver because
the registers have differences that haven't been accounted for yet.
Basically, I'm focused on the 6xxx series right now. I apologize for
those seeing problems on the 5xxx series, I've not had a chance to
look at those problems yet.
For those curious, the previous bug causing the SCSI timeout and
subsequent panics was caused by an improper clear of hc_irq_cause in
mv_host_intr().
This version is running well in my environment (6081 chips,
with/without SW raid1) and is showing equal or better performance
compared to the Marvell driver (mv_sata) in my initial tests (timed
dd's of reads/writes to/from memory/disk).
I still need to look at the causes of occasional problems such as this:
ata11: translating stat 0x35 err 0x00 to sense
ata11: status=0x35 { DeviceFault SeekComplete CorrectedError Error }
SCSI error : <10 0 0 0> return code = 0x8000002
Current sda: sense key Hardware Error
end_request: I/O error, dev sda, sector 3155010
and this, seen at init time:
ATA: abnormal status 0x80 on port 0xE093911C
but they aren't showstoppers.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch introduces new feature in qeth:
qeth enhancement provides the device driver support for
the Communication Controller for Linux on System z9 and zSeries
(CCL), which is software that enables running the Network Control
Program (NCP) on a zSeries machine. The OSA CDLC support is based
on a new IBM mainframe CHPID type called Open Systems Adaper for
NCP (OSN). In case of OSN qeth communicates with the type-OSN
OSA-card on one hand, and with the CCL-kernel-component Network
Device Handler (NDH) on the other.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unregister all netdevs before freeing local data. I was unable to
trigger any crashes without this change when running busy loops for
driver operations when ejecting a Prism2 PC Card. Anyway, should there
be a race condition with this, better make it less likely to happen by
unregistering the netdevs first.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
local->hw_priv was being freed and set to NULL just before calling
prism2_free_local_data(). However, this may expose a race condition in
which something ends up trying to use hw_priv during shutdown. I
haven't noticed this happening, but better be safe than sorry, so
let's postpone hw_priv freeing to happen only after
prism2_free_local_data() has returned.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The debug version of I/O functions in hostap_pci had not survived the
change to start using hw_priv pointer, so let's fix them to actually
define the local hw_priv variable.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Host AP driver used hardware model specific dev_open/close handlers
that were called on dev_open/close if the hardware driver had
registered the handler. These were only used for hostap_cs and only
for tracking whether any of the netdevs were UP. This information is
already available from local->num_dev_open, so there is not need for
the special open/close handler.
Let's get rid of these handlers. In addition to cleaning up the code,
this fixes a module refcounting issue for hostap_cs where ejecting the
card while any of the netdevs were open did not decrement refcount
properly.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since our max_lun is unconditionally set to 1, we might as well
hardcode a LUN 0 probe, rather than a wildcard LUN scan.
The ide-scsi driver sets max_lun to a value greater than under
certain conditions:
if ((drive->id->last_lun & 0x7) != 7)
host->max_lun = (drive->id->last_lun & 0x7) + 1;
else
host->max_lun = 1;
last_lun is Word 126 of IDENTIFY PACKET DEVICE, marked as obsolete
and undocumented in non-ancient specs. We'll leave it out for now.
Should the need arise to support multi-LUN ATAPI devices, we'll
probably want to add the above code.
Finally, there have been reports of REPORT LUNS commands locking up
ATAPI drives. Eliminating the wildcard LUN scan could help reduce
the trouble from problematic drives.
eliminate the double copy, and improve cifs write performance and
help the server by upping the typical write size from 4K to 16K
(or even larger if wsize set explicitly) for servers which support this.
Part 1 of 2
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch fixes up a few problems with jfs's reserved inodes.
1. There is no need for the jfs code setting the I_DIRTY bits in i_state.
I am ashamed that the code ever did this, and surprised it hasn't been
noticed until now.
2. Make sure special inodes are on an inode hash list. If the inodes are
unhashed, __mark_inode_dirty will fail to put the inode on the
superblock's dirty list, and the data will not be flushed under memory
pressure.
3. Force writing journal data to disk when metapage_writepage is unable to
write a metadata page due to pending journal I/O.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
initialized which can cause problems for drivers that expect the network
structure to be completely filled in.
This patch will make sure the network is filled in as much as possible.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
results in a lot of duplicate code.
This will move the parsing stage into a seperate function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
net/ieee80211/ieee80211_tx.c:215:9: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
header, and I also added the ieee80211_is_cck_rate counterpart.
Various drivers currently create there own version of these functions,
but I guess the ieee80211 stack is the best place to provide such
routines.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Now that we use the device tree, it helps to build it in.
It helps to links the kernel at the correct address.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Use idle_power4.S from ppc64 as we are not going to support
32 bit power4 in the merged tree.
Merge ppc64 traps.c into powerpc traps.c:
use ppc64 versions of exception routine names
(as they don't have StudlyCaps)
make all the versions if die() have the same
prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This updates the powermac SMP code to use the mpic driver instead of
the openpic driver and fixes the SMP-dependent context switch code.
We had a subtle bug where we were using interrupt numbers 256-259 for
IPIs, but ppc32 had NR_IRQS = 256. Moved the IPIs down to use interrupt
numbers 252-255 instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to get some better debugging from people about certain hangs/crashes
we need to be able to turn AGP writeback off permanently...
Signed-off-by: Dave Airlie <airlied@linux.ie>
Matthew Wilcox pointed out that swiotlb.c implements a generic
interface that is not tied to just PCI. Remove includes of
<linux/pci.h>, <asm/pci.h>. Fix comments and printk() messages
to no longer refer to PCI.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Re-implement dma_sync_single_range_for_{cpu,device} for x86_64 using
swiotlb_sync_single_range_for_{cpu,device}.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change comment at top of swiotlb.c to reflect that the code is shared
with EM64T (i.e. Intel x86_64). Also add an entry for myself so that
if I "broke it", everyone knows who "bought it"... :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current implementation of sync_single in swiotlb.c chokes on
DMA_BIDIRECTIONAL mappings. This patch adds the capability to sync
those mappings, and optimizes other syncs by accounting for the
sync target (i.e. cpu or device) in addition to the DMA direction of
the mapping.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch implements swiotlb_sync_single_range_for_{cpu,device}. This
is intended to support an x86_64 implementation of
dma_sync_single_range_for_{cpu,device}.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The implementations of swiotlb_sync_single_for_{cpu,device} are
identical. Likewise for swiotlb_syng_sg_for_{cpu,device}. This patch
move the guts of those functions to two new inline functions, and
calls the appropriate one from the bodies of those functions.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The swiotlb implementation is shared by both IA-64 and EM64T. However,
the source itself lives under arch/ia64. This patch moves swiotlb.c
from arch/ia64/lib to lib/ and fixes-up the appropriate Makefile and
Kconfig files. No actual changes are made to swiotlb.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/proc/iomem describes a block of memory as "Kernel data",
but the end address is derived from "_edata". The kernel
actually has many other sections beyond _edata. Get the
real end address from _end.
Acked-by: Khalid Aziz <khalid_aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Increase the maximum system size of SGI SN systems. Note that
this is not the maximum SSI size. The maximum system size is
the number of nodes in the numalink domain.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some IRQ controllers don't need an ack function (e.g. OpenPIC on
PPC platforms) and for them we'd rather not have the overhead
of doing an indirect call to a function that does nothing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges ppc_ksyms.c, puts back the actual do_execve call in
sys_execve, makes init_MMU call find_end_of_memory rather than
ppc_md.find_end_of_memory (every platform has a device tree
with a /memory node now, right?) and fixes some problems with the
mpic initialization on newworld powermacs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed ppc32 so that cur_cpu_spec is just a single pointer for all CPUs.
Additionally, made call_setup_cpu check to see if the cpu_setup pointer
is NULL or not before calling the function. This lets remove the dummy
cpu_setup calls that just return.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merged cputable.h between ppc32 and ppc64. In doing this removed support
for the BEGIN_FTR_SECTION/END_FTR_SECTION macros in C code since they
dont compile correctly. C code should use cpu_has_feature(). This is
based on Arnd Bergmann's initial patch.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge byteorder.h
Essentially adopts the 64-bit version of this file. The 32-bit version had
been using unsigned ints for arguments/return values that were actually
only 16 bits - the new file uses __u16 for these items as in the 64-bit
version of the header. The order of some of the asm constraints
in the 64-bit version was slightly different than the 32-bit version,
but they produce identical code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and rename it to pci.c. This also required moving
arch/ppc64/kernel/pci.h into include/asm-powerpc (called
ppc-pci.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Rename it to hvcall.S and (so I can do that) rename hvcall.c
to hvlog.c - a more appropriate name.
Do some white space cleanups.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
iSeries_setup.c becomes setup.c
iSeries_setup.h becomes setup.h
mf.c retains its name
Also moved iSeries_[gs]et_rtc_time and iSeries_get_boot_time into
mf.c since they are just small wrappers around mf_ functions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Complete moving arch/ppc64/kernel/mpic.h,
include/asm-ppc/reg.h, include/asm-ppc64/kdebug.h
and include/asm-ppc64/kprobes.h
Add arch/powerpc/platforms/Makefile and use it from
arch/powerpc/Makefile
Introduce OLDARCH temporarily so we can point back to
the originating architecture
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge semaphore.h
Adopted the ppc64 version of semaphore.h. The 32-bit version used
smp_wmb(), but recent updates to atomic.h mean this is no longer required.
The 64-bit version made use of unlikely(), which has been retained in the
combined version.
This patch requires the recent atomic.h patch.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc*/rwsem.h into include/asm-powerpc.
Removed smp_*mb() memory barriers from the ppc32 code
as they are now burried in the atomic_*() functions as
suggested by Paul, implemented by Arnd, and pushed out
by Becky. I am not the droid you are looking for.
This patch depends on Becky's atomic.h merge patch.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge atomic.h and memory.h into powerpc
Merged atomic.h into include/powerpc. Moved asm-style HMT_ defines from
memory.h into ppc_asm.h, where there were already HMT_defines; moved c-style
HMT_ defines to processor.h. Renamed memory.h to synch.h to better reflect
its contents.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <linuxppc@jdl.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The spinlock_types.h merge renamed the structure for raw_spinlock_t to
match ppc64. In doing so some of the spinlock macros/functions needed to
be updated to match. Apparently, this seems to only be caught when
building power3.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I've been threatening this for a while, so no point hanging around.
This lindents the DRM code which was always really bad in tabbing department.
I've also fixed some misnamed files in comments and removed some trailing
whitespace.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Now that we are compiling with -fno-strict-aliasing (this is the
kernel default), we can drop the following kludge for
iwe_stream_add_event().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for WE-19 to the HostAP driver. One of
the major change is the use of an explicit flag to tell if iwstat is
in dBm or not.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_pci and hostap_plx drivers still use PCI driver names
"prism2_pci" and "prism2_plx" respectively. This is unfriendly to
linux-wlan-ng, which uses the same names. So, if e.g. hostap_pci and
prism2_pci are loaded, they will "share" /sys/bus/pci/drivers/prism2_plx
directory.
Change PCI driver names of hostap_pci and hostap_plx to be equal to
their module names.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Go back to what 2.4 kernels used to do here, as if this hits,
the kernel just hangs indefinitly.
Actually an improvement over 2.4 - we now break; out of the loop
instead of just printing messages on timeouts.
Signed-off-by: Dave Jones <davej@redhat.com>
This patch adds a #define for SN_SAL_IOIF_PCI_SAFE and makes that the
preferred method of implementing sn_pci_legacy_read() and
sn_pci_legacy_write().
This SAL call has been present in SGI proms since version 4.10. If the
SN_SAL_IOIF_PCI_SAFE call fails, revert to the previous code for compatability
with older proms.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Via reading the code, my understanding is that powernow-k8 uses
preempt_disable to ensure that driver->target doesn't migrate across cpus
whilst it's accessing per processor registers, however set_cpus_allowed
will provide this for us. Additionally, remove schedule() calls from
set_cpus_allowed as set_cpus_allowed ensures that you're executing on the
target processor on return.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The in-kernel portmapper does in fact need a reserved port when registering
new services, but not when performing bind queries.
Ensure that we distinguish between the two cases.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Address space resources for ACPI devices have a producer/consumer
flag. All devices "consume" the indicated address space. If the
resource is marked as a "producer", the range is also passed on
to child devices.
We currently ignore this flag when setting up MMIO and I/O port
windows for PCI root bridges, so we could mistakenly interpret
a "consumed-only" range, like CSR space for the device itself,
as a window that is routed to children.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently rpc_mkdir/rpc_rmdir and rpc_mkpipe/mk_unlink have an API that's
a little unfortunate. They take a path relative to the rpc_pipefs root and
thus need to perform a full lookup. If you look at debugfs or usbfs they
always store the dentry for directories they created and thus can pass in
a dentry + single pathname component pair into their equivalents of the
above functions.
And in fact rpc_pipefs actually stores a dentry for all but one component so
this change not only simplifies the core rpc_pipe code but also the callers.
Unfortuntately this code path is only used by the NFS4 idmapper and
AUTH_GSSAPI for which I don't have a test enviroment. Could someone give
it a spin? It's the last bit needed before we can rework the
lookup_hash API
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In fact, ->set_buffer_size should be completely functionless for non-UDP.
Test-plan:
Check socket buffer size on UDP sockets over time.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Each transport implementation can now set unique bind, connect,
reestablishment, and idle timeout values. These are variables,
allowing the values to be modified dynamically. This permits
exponential backoff of any of these values, for instance.
As an example, we implement exponential backoff for the connection
reestablishment timeout.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement a best practice: if the remote end drops our connection, try to
reconnect using the same port number. This is important because the NFS
server's Duplicate Reply Cache often hashes on the source port number.
If the client reuses the port number when it reconnects, the server's DRC
will be more effective.
Based on suggestions by Mike Eisler, Olaf Kirch, and Alexey Kuznetsky.
Test-plan:
Destructive testing.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Select an RPC client source port between 650 and 1023 instead of between
1 and 800. The old range conflicts with a number of network services.
Provide sysctls to allow admins to select a different port range.
Note that this doesn't affect user-level RPC library behavior, which
still uses 1 to 800.
Based on a suggestion by Olaf Kirch <okir@suse.de>.
Test-plan:
Repeated mount and unmount. Destructive testing. Idle timeouts.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: Move some macros that are specific to the Van Jacobson
implementation into xprt.c. Get rid of the cong_wait field in
rpc_xprt, which is no longer used. Get rid of xprt_clear_backlog.
Test-plan:
Compile with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Get rid of the "xprt->nocong" variable.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss with UDP mounts.
Look for significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The final place where congestion control state is adjusted is in
xprt_release, where each request is finally released. Add a callout
there to allow transports to perform additional processing when a
request is about to be released.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
A new interface that allows transports to adjust their congestion window
using the Van Jacobson implementation in xprt.c is provided.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for
significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow transports to hook the retransmit timer interrupt. Some transports
calculate their congestion window here so that a retransmit timeout has
immediate effect on the congestion window.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The next method we abstract is the one that releases a transport,
allowing another task to have access to the transport.
Again, one generic version of this is provided for transports that
don't need the RPC client to perform congestion control, and one
version is for transports that can use the original Van Jacobson
implementation in xprt.c.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for
significant regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The next several patches introduce an API that allows transports to
choose whether the RPC client provides congestion control or whether
the transport itself provides it.
The first method we abstract is the one that serializes access to the
RPC transport to prevent the bytes from different requests from mingling
together. This method provides proper request serialization and the
opportunity to prevent new requests from being started because the
transport is congested.
The normal situation is for the transport to handle congestion control
itself. Although NFS over UDP was first, it has been recognized after
years of experience that having the transport provide congestion control
is much better than doing it in the RPC client. Thus TCP, and probably
every future transport implementation, will use the default method,
xprt_lock_write, provided in xprt.c, which does not provide any kind
of congestion control. UDP can continue using the xprt.c-provided
Van Jacobson congestion avoidance implementation.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare the way to remove the "xprt->nocong" variable by adding a callout
to the RPC client transport switch API to handle setting RPC retransmit
timeouts.
Add a pair of generic helper functions that provide the ability to set a
simple fixed timeout, or to set a timeout based on the state of a round-
trip estimator.
Test-plan:
Use WAN simulation to cause sporadic bursty packet loss. Look for significant
regression in performance or client stability.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now we can fix up the last few places that use the "xprt->stream"
variable, and get rid of it from the rpc_xprt structure.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a generic mechanism for skipping over transport-specific headers
when constructing an RPC request. This removes another "xprt->stream"
dependency.
Test-plan:
Write-intensive workload on a single mount point (try both UDP and
TCP).
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Split the RPC client's main socket write path into a TCP version and a UDP
version to eliminate another dependency on the "xprt->stream" variable.
Compiler optimization removes unneeded code from xs_sendpages, as this
function is now called with some constant arguments.
We can now cleanly perform transport protocol-specific return code testing
and error recovery in each path.
Test-plan:
Millions of fsx operations. Performance characterization such as
"sio" or "iozone". Examine oprofile results for any changes before and
after this patch is applied.
Version: Thu, 11 Aug 2005 16:08:46 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Create separate connection worker functions for managing UDP and TCP
transport sockets. This eliminates several dependencies on "xprt->stream".
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon with
v2, v3, and v4.
Version: Thu, 11 Aug 2005 16:08:18 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Split the socket write space callback function into a TCP version and UDP
version, eliminating one dependence on the "xprt->stream" variable.
Keep the common pieces of this path in xprt.c so other transports can use
it too.
Test-plan:
Write-intensive workload on a single mount point.
Version: Thu, 11 Aug 2005 16:07:51 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: change some comments to reflect the realities of the new RPC
transport switch mechanism. Get rid of unused xprt_receive() prototype.
Also, organize function prototypes in xprt.h by usage and scope.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:07:21 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: remove only reference to xprt->pending from the socket transport
implementation. This makes a cleaner interface for other transport
implementations as well.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:06:52 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: get rid of unnecessary socket.h and in.h includes in the generic
parts of the RPC client.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:06:23 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: get rid of a name reference to sockets in the generic parts of the
RPC client by renaming the sockstate field in the rpc_xprt structure.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:05:53 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: Replace the xprt_lock with something more aptly named. This lock
single-threads the XID and request slot reservation process.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:05:26 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: replace a name reference to sockets in the generic parts of the RPC
client by renaming sock_lock in the rpc_xprt structure.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:05:00 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Reduce stack utilization of the RPC socket transport's send path.
A couple of unlikely()s are added to ensure the compiler places the
tail processing at the end of the csect.
Test-plan:
Millions of fsx operations. Performance characterization such as "sio" or
"iozone".
Version: Thu, 11 Aug 2005 16:04:30 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce block header comments and a function naming convention to the
socket transport implementation. Provide a debug setting for transports
that is separate from RPCDBG_XPRT. Eliminate xprt_default_timeout().
Provide block comments for exposed interfaces in xprt.c, and eliminate
the useless obvious comments.
Convert printk's to dprintk's.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Version: Thu, 11 Aug 2005 16:04:04 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Move the bulk of client-side socket-specific code into a separate source
file, net/sunrpc/xprtsock.c.
Test-plan:
Millions of fsx operations. Performance characterization such as "sio" or
"iozone". Destructive testing (unplugging the network temporarily, server
reboots). Connectathon with v2, v3, and v4.
Version: Thu, 11 Aug 2005 16:03:38 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean-up: Move some code that is common to both RPC client- and server-side
socket transports into its own source file, net/sunrpc/socklib.c.
Test-plan:
Compile kernel with CONFIG_NFS enabled. Millions of fsx operations over
UDP, client and server. Connectathon over UDP.
Version: Thu, 11 Aug 2005 16:03:09 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The in-kernel portmapper does not require a reserved port for making
bind queries.
Test-plan:
Tens of runs of the Connectathon locking suite with TCP and UDP
against several other NFS server implementations using NFSv3,
not NFSv4 (which doesn't require rpcbind).
Version: Thu, 11 Aug 2005 16:02:43 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement a best practice: don't use exponential backoff when computing
retransmit timeout values on TCP connections, but simply retransmit
at regular intervals.
This also fixes a bug introduced when xprt_reset_majortimeo() was added.
Test-plan:
Enable RPC debugging and watch timeout behavior on a NFS/TCP mount.
Version: Thu, 11 Aug 2005 16:02:19 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement a best practice: for soft mounts, an rpcbind timeout should
cause an RPC request to fail.
This also provides an FSM hook for retrying an rpcbind with a different
rpcbind protocol version. We'll use this later to try multiple rpcbind
protocol versions when binding. To enable this, expose the RPC error
code returned during a portmap request to the FSM so it can make some
decision about how to report, retry, or fail the request.
Test-plan:
Hundreds of passes with connectathon NFSv3 locking suite, on the client
and server.
Version: Thu, 11 Aug 2005 16:01:53 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix up xprt_connect_status: the soft timeout logic was clobbering tk_status,
so TCP connect errors were not properly reported on soft mounts.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP.
Version: Thu, 11 Aug 2005 16:01:28 -0400
Signed-off-by: Chuck Lever <cel@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fixes a condition whereby the kernel is returning the non-POSIX error
EBADCOOKIE to userspace.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[PATCH] Fix miscompare in __posix_lock_file
If an application requests the same lock twice, the
kernel should just leave the existing lock in place.
Currently, it will install a second lock of the same type.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When doing a rename on top of an existing file that is not in use,
the inode of the overwritten file will remain in the icache.
The fix is to decrement i_nlink of the overwritten inode, like we
do for unlink, rmdir etc already.
Problem diagnosed by Olaf Kirch. This patch is a slight variation
on his fix.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Read only needed data in __orinoco_ev_txexc().
Don't read the 802.11 header beyond addr1. The rest of the frame is not
used currently.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Annotate endianess of variables and structure members.
Don't reuse variables for both host-endian and little-endian data.
Minor comment changes in affected structures.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove unneeded forward declarations.
Also reorder struct pcmcia_driver initialization to keep attach and
detach together.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
orinoco_send_wevents() could return without unlocking.
Failure to read BSSID from the hardware would cause orinoco_send_wevents() to
return with lock held. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Fix memory leak and unneeded unlock in orinoco_join_ap()
If orinoco_lock() fails, the code would still run orinoco_unlock(),
instead of freeing the allocated memory. Found by sparse.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove inneeded system includes.
Most system includes are not needed. In particular, the hardware
backends don't need anything network related. Some includes have been
moved from local headers to the C files where they are actually used.
Includes that have to be in the local headers are no longer from the C
sources.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the /cpus node and nodes for each cpu, as well as cache size properties,
reg propery, "linux,boot-cpu", and timebase/clock frequency.
With those properties in place we can remove:
- setup_iSeries_cache_sizes()
- code in iSeries_setup_arch() to calculate timebase etc.
- iSeries_calibrate_decr()
- smp_iSeries_numProcs() and simplify smp_iSeries_probe()
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Add /chosen/linux,platform to the device tree so we can remove iSeries
specific code in setup_system() to set systemcfg->platform.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This patch adds the required nodes to the iSeries device tree to allow
early_init_devtree() to do the lmb setup for us.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Misc steps to incorporate the flat device tree on iSeries.
- define iseries_probe()
- call build_iSeries_Memory_Map() earlier
- return __pa() of the flat device tree from iSeries_early_setup()
- actually call early_setup() for iSeries
- add iseries_md to machdep_calls
- build prom.o for iSeries
- enable /proc/device-tree for iSeries
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This patch adds infrastructure for creating a fake flattened device tree
on iSeries.
We also need to build prom.o for iSeries which means we'll always need it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We don't need to call smp_release_cpus() on iSeries but it's harmless
if we do and it removes another #ifdef ISERIES.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We don't need to call stab_initialize() for the boot cpu on iSeries, so
we hack around it so that early_setup() can be called on iSeries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
early_setup() calls htab_initialize() which is similar, but not identical
to iSeries_bolt_kernel().
On iSeries the Hypervisor has already inserted some ptes for us, and we
simply have to detect that and bolt them. iSeries_hpte_bolt_or_insert()
implements that logic.
For the case of a non-existing pte we just call iSeries_hpte_insert(). This
appears to work, although it's not entirely equivalent to the old code in
iSeries_make_pte() which panicked if we got a secondary slot. Not sure if
that's important.
Finally we call iSeries_hpte_bolt_or_insert() from create_pte_mapping(),
which is called from htab_initialize() for each lmb region.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
In order to call finish_device_tree() on iSeries we need to define
virt_irq_create_mapping(). We also need to set ppc64_interrupt_controller to
something other than zero. If we want to do interrupt setup via the device
tree on iSeries this code will need some serious work, but it's harmless to
have it there as long as the nodes in the iSeries device tree don't cause
it to be invoked.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Move the iSeries machine specific calls into a machdep_calls struct like
other platforms, rather than setting members of ppc_md explicitly.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Most important of these fixes mapchars on bigendian and a few statfs fields
Signed-off-by: Shaggy (shaggy@austin.ibm.com)
Signed-off-by: Steve French (sfrench@us.ibm.com)
Changed crypto method from requiring a struct ieee80211_device reference
to the init handler. Instead we now have a get/set flags method for
each crypto component.
Setting of TKIP countermeasures can now be done via
set_flags(IEEE80211_CRYPTO_TKIP_COUNTERMEASURES)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 0254e7c97cece038cd11b47a16027c6379e464fe
parent a84f7713dc87ca1b51c6d53b391087663425a080
author James Ketrenos <jketreno@linux.intel.com> 1126661324 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127319069 -0500
Updated based on Michael Wu's patch and comments sent to netdev.
Added IE comments to ieee80211_* frame structures.
Changed reason_code to reason (consistency)
Removed info_element from ieee80211_disassoc
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree de81b55e78e85997642c651ea677078d0554a14f
parent c8030da8c159f8b82712172a6748a42523aea83a
author James Ketrenos <jketreno@linux.intel.com> 1127104380 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127315225 -0500
Added handle_deauth() callback.
Enhanced crypt_{tkip,ccmp} to support varying splits of HW/SW offload.
Changed channel freq to u32 from u16.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree c1b50ac5d2d1f9b727c39c6bd86a7872f25a1127
parent 1bb997a3ac7dd1941e02426d2f70bd28993a82b7
author James Ketrenos <jketreno@linux.intel.com> 1126720779 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127314674 -0500
Added subsystem version string and reporting via MODULE_VERSION and
pritnk during load.
NOTE: This is the version support split out from patch 24/29 of the
prior series.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merged hw_irq.h between ppc32 & ppc64. Added support to use the Book-E
wrtee[i] instructions that allow modifying MSR[EE] atomically.
Additionally, added get_irq_desc() macros to ppc32 to allow mask_irq(),
unmask_irq(), and ack_irq() to be common between ppc32 & ppc64.
Note: because 64-bit Book-E implementations only have a 32-bit MSR the
macro's for Book-E need to come before the PPC64 macro's to ensure the
right thing happends for 64-bit Book-E processors.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merging of auxvec.h into asm-powerpc introduced the AT_SYSINFO_EHDR
into the ppc32 build that is used for VDSO. However, we dont have VDSO
support in the ppc32 tree at this time. Introducing this define causes
a number of other things to get built with the assumption of VDSO, thus
causing the compile errors for ppc32.
Until we have VDSO on ppc32 we will leave AT_SYSINFO_EHDR a ppc64 only
define.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
functional, and the length check is fixed so readdir does not throw a
warning message when windows me messes up the response to FindFirst
of an empty dir (with only . and ..).
Signed-off-by: Steve French (sfrench@us.ibm.com)
Recent forcedeth nics support checksum offloading for tx.
The attached patch, written by Ayaz Abdulla, adds the support to the
driver.
It also cleans up the handling of the three dma ring entry formats that
are supported by the driver.
Signed-off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-By: Jeff Garzik <jgarzik@pobox.com>
Remove old WIRELESS_EXT version compatibility
In-tree doesn't need to maintain backward compatibility.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8c1676c8a15c08e6d4c718fc7cd42d9bf4cd8235
parent 0ccc3dd6469ed492578c184f47dde2baccde3593
author James Ketrenos <jketreno@linux.intel.com> 1126715240 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316717 -0500
Updated hostap to be compatible with extra_prefix_len changes.
Accomplished via:
for i in hostap_ap.c hostap_80211_tx.c; do
sed -i -e "s:\([.>]\)extra_prefix_len:\1extra_mpdu_prefix_len:g" \
-e "s:\([.>]\)extra_postfix_len:\1extra_mpdu_postfix_len:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8ec97d9056ceaf0f845ed51175dd842b700baadd
parent 329128457008ace3110c96971addf85a767dd5af
author James Ketrenos <jketreno@linux.intel.com> 1126714484 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316636 -0500
Updated hostap to be compatible with ieee80211_hdr changes.
Change accomplished via:
for i in hostap_ap.{c,h} hostap_80211_{t,r}x.c; do
sed -i -e "s:ieee80211_hdr\([^_]\):ieee80211_hdr_4addr\1:g" \
drivers/net/wireless/hostap/$i
done
CC: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 0d3e41e574fcb41b9da7f0b7e1d27ec350726654
parent dbe2885fe2f454d538eaaabefc741ded1026f476
author James Ketrenos <jketreno@linux.intel.com> 1126720499 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127314531 -0500
Updated copyright dates.
NOTE: This is a split out of just the copyright updates from patch
24/29 in the prior series.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 5c7559a1216ae1121487f6aed94a6017490729b3
parent c1ff4c22e5622c8987bf96c09158c4924cde98c2
author Hong Liu <hong.liu@intel.com> 1125482767 +0800
committer James Ketrenos <jketreno@linux.intel.com> 1127314427 -0500
Mixed PTK/GTK CCMP/TKIP support.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree bce04549ce0a8239d8083d8da5c3d12f7e1aecd9
parent b15a5153d5f1c75d9435d5ce19b52287059d5d54
author Adrian Bunk <bunk@stusta.de> 1125026386 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313953 -0500
"extern inline" doesn't make much sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 589bbb92ce7cdf7c2ae820b0ebd3f8fbf1baeee9
parent c6ce9081e79e8836a11e86e3d38297521a2420be
author Jiri Benc <jbenc@suse.cz> 1125015310 -0400
committer James Ketrenos <jketreno@linux.intel.com> 1127313914 -0500
Additional fixes for endian-aware types
Based on the application of __le16/__be16 changes already made w/ a
prior patch by Michael Wu <flamingice@sourmilk.net>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 383c59b2516a61f2683f02dfebbed0caf6ee5dc3
parent a04948f63fd96c4b875a43f78afad1a0874cc441
author Mike Kershaw <dragorn@kismetwireless.net> 1124447833 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313883 -0500
Added ieee80211_radiotap.h to enhance statistic reporting to user space
from wireless drivers.
Signed-off-by: Mike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 385b391fc0d7c124cd0547fdb6183e9a0c333391
parent 97d7a47f76e72bedde7f402785559ed4c7a8e8e8
author James Ketrenos <jketreno@linux.intel.com> 1124447590 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313735 -0500
Added ieee80211_geo to provide helper functions to drivers for
implementing supported channel maps.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree a3ad796273e98036eb0e9fc063225070fa24508a
parent 1b9c0aeb377abf8e4a43a86cff42382f74ca0259
author Mohamed Abbas <mabbas@linux.intel.com> 1124447069 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313435 -0500
Add QoS (WME) support to the ieee80211 subsystem.
NOTE: This requires drivers that use the ieee80211 hard_start_xmit
(ipw2100 and ipw2200) to add the priority parameter to their callback.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree ba6509c7cd1dd4244a2f285f2da5d632e7ffbb25
parent 7b5f9f2ddcabdaea214527a895e6e8445cafdd80
author James Ketrenos <jketreno@linux.intel.com> 1124447000 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313383 -0500
Per the conversations with folks at OLS, the QoS layer in 802.11
drivers can now result in NETDEV_TX_BUSY being returned when the queue
a packet is targetted for is full.
To implement this, ieee80211_xmit will now call the driver's
is_queue_full to determine if the current priority queue is full. If
so, NETDEV_TX_BUSY is returned to the kernel and no processing is done
on the frame.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 8428e9f510e6ad6c77baec89cb57374842abf733
parent d78bfd3ddae9c422dd350159110f9c4d7cfc50de
author Liu Hong <hong.liu@intel.com> 1124446520 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313183 -0500
Fix TKIP, repeated fragmentation problem, and payload_size reporting
1. TKIP encryption
Originally, TKIP encryption issues msdu + mpdu encryption on every
fragment. Change the behavior to msdu encryption on the whole
packet, then mpdu encryption on every fragment.
2. Avoid repeated fragmentation when !host_encrypt.
We only need do fragmentation when using host encryption. Otherwise
we only need pass the whole packet to driver, letting driver do the
fragmentation.
3. change the txb->payload_size to correct value
FW will use this value to determine whether to do fragmentation. If
we pass the wrong value, fw may cut on the wrong bound which will
make decryption fail when we do host encryption.
NOTE: This requires changing drivers (hostap) that have
extra_prefix_len used within them (structure member name change).
Signed-off-by: Hong Liu <liu.hong@intel.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 40adc78b623ae70d56074934ec6334eb4f0ae6a5
parent db43d847bcebaa3df6414e26d0008eb21690e8cf
author James Ketrenos <jketreno@linux.intel.com> 1124445938 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313102 -0500
Added ieee80211_tx_frame to convert generic 802.11 data frames into
txbs for transmission.
Added several purpose specific callbacks (handle_assoc, handle_auth,
etc.) which the driver can register with for being notified on
reception of variouf frame elements.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree b45c9c1017fd23216bfbe71e441aed9aa297fc84
parent 04aacdd71e904656a304d923bdcf57ad3bd2b254
author Ivo van Doorn <IvDoorn@gmail.com> 1124445405 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313029 -0500
This patch adds support for the creation of RTS packets when the
config flag CFG_IEEE80211_RTS has been set.
Signed-Off-By: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree e9c18b2c8e5ad446a4d213243c2dcf9fd1652a7b
parent 4e97ad6ae7084a4f741e94e76c41c68bc7c5a76a
author James Ketrenos <jketreno@linux.intel.com> 1124444315 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127312922 -0500
Renamed ieee80211_hdr to ieee80211_hdr_3addr and modified ieee80211_hdr
to just contain the frame_ctrl and duration_id.
Changed uses of ieee80211_hdr to ieee80211_hdr_4addr or
ieee80211_hdr_3addr based on what was expected for that portion of code.
NOTE: This requires changes to ipw2100, ipw2200, hostap, and atmel
drivers.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 1536f39c18756698d033da72c49300a561be1289
parent 07172d7c9f10ee3d05d6f6489ba6d6ee2628da06
author Liu Hong <hong.liu@intel.com> 1124436225 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127312664 -0500
Added WE-18 support to default wireless extension handler in ieee80211
subsystem.
Updated patch since last send to account for ieee80211_device parameter
being added to the crypto init method.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 898fedef6ca1b5b58b8bdf7e6d8894a78bbde4cd
parent 8720fff53090ae428d2159332b6f4b2749dea10f
author Zhu Yi <jketreno@io.(none)> 1124435746 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127312509 -0500
Allow drivers to fix an issue when using wpa_supplicant with WEP.
The problem is introduced by the hwcrypto patch. We changed indicator of
the encryption request from the upper layer (i.e. wpa_supplicant):
In the original host based crypto the driver could use: crypt &&
crypt->ops.
In the new hardware based crypto, the driver should use the flags
specified in ieee->sec.encrypt.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree b69e983266840983183a00f5ac02c66d5270ca47
parent cdd6372949b76694622ed74fe36e1dd17a92eb71
author Zhu Yi <jketreno@io.(none)> 1124435425 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127312421 -0500
Fix kernel Oops when module unload.
Export a new function ieee80211_crypt_quiescing from ieee80211. Device
drivers call it to make the host crypto stack enter the quiescence
state, which means "process existing requests, but don't accept new
ones". This is usually called during a driver's host crypto data
structure free (module unload) path.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree b9cdd7058b787807655ea6f125e2adbf8d26c863
parent 85d9b2bddfcf3ed2eb4d061947c25c6a832891ab
author Zhu Yi <jketreno@io.(none)> 1124435212 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127312152 -0500
Fix time calculation, switching to use jiffies_to_msecs.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 5322d496af90d03ffbec27292dc1a6268a746ede
parent 6c9364386ccb786e4a84427ab3ad712f0b7b8904
author James Ketrenos <jketreno@linux.intel.com> 1124432367 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127311810 -0500
Hardware crypto and fragmentation offload support added (Zhu Yi)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 367069f24fc38b4aa910e86ff40094d2078d8aa7
parent a33a198201
author James Ketrenos <jketreno@linux.intel.com> 1124430800 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127310571 -0500
Fixed a kernel oops on module unload by adding spin lock protection to
ieee80211's crypt handlers (thanks to Zhu Yi)
Modified scan result logic to report WPA and RSN IEs if set (vs.being
based on wpa_enabled)
Added ieee80211_device as the first parameter to the crypt init()
method. TKIP modified to use that structure for determining whether to
countermeasures are active.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 713b6ff3311decfe42d5209f7b2508736d144b85
parent 6465beff0e89779330450dffc2a5e6dc5154eebf
author James Ketrenos <jketreno@linux.intel.com> 1126716726 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316162 -0500
Updated ipw2200 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 9f86c7b4f59249c05c96c360dfaa817995e8a44f
parent 9b09701b2c6254f2fddb009004a14eb5a908714f
author James Ketrenos <jketreno@linux.intel.com> 1126714305 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316074 -0500
Updated ipw2200 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree ee48cbe413b795d6be454b9baf4f3bd3d74814cb
parent 49856b147763bd6847e0d8f53aee1ddd61385638
author James Ketrenos <jketreno@linux.intel.com> 1126716634 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127316024 -0500
Updated ipw2100 to be compatible with ieee80211's hard_start_xmit change.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
tree 992b203395c50342f1cced415acae6177344e270
parent c59bb604a2ff4e40232ff0422e7adc44e3b007a0
author James Ketrenos <jketreno@linux.intel.com> 1126714006 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127315910 -0500
Updated ipw2100 to be compatible with ieee80211_hdr changes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ppc/ppc64: Merge elf.h into include/asm-powerpc
Merge elf.h into a single include file for 32 and 64-bit ppc platforms. This
patch has been tested on 32-bit and built on 64-bit platforms.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <Becky.Bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc32/ppc64: Merge bug.h into include/asm-powerpc
This patch merges bug.h into include/asm-powerpc. Changed the data
structure for bug_entry such that line is always an int on both 32 and
64-bit platforms; removed casts to int from the 64-bit trap code to
reflect this.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <Becky.Bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a revised patch to merge asm-ppc*/hardirq.h.
It removes some unnecessary #includes, but then requires
the addition of #include <asm/irq.h> in PPC32's hw_irq.h
much like ppc64 already does. Furthermore, several
unnecessary #includes were removed from some ppc32 boards
in order to break resulting bad #include cycles.
Builds pSeries_defconfig and all ppc32 platforms except
the already b0rken bseip.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 timer_interrupt() returned a value that was never used. Changed
the ppc64 version of timer_interrupt() to no longer return a value so
that the signatures between ppc32 & ppc64 match. This will simplify
future merging of arch/powerpc.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename and slightly modify {request,free}_perfmon_irq in the ppc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- merge common.c
- move model specific files
- remove stub Makefiles
- clean up arch/ppc*/Makefile
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge include/asm-ppc64/oprofile_ipml.h and arch/ppc/oprofile/op_impl.h
into include/asm-powerpc/oprofile_ipml.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file is the same in both architectures so create arch/powerpc/kernel
and move it there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Made the CHRP/PMAC/PREP config options selectable by the user.
This allows us to build kernels specifically for one of the
platforms thus reducing code size.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch slightly change the TLB flush batch mecanism so that we
store the full vaddr (including vsid) when adding an entry to the
batch so that the flush part doesn't have to get to the context.
This cleans it a bit, and paves the way to future updates like
dynamic vsids.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace some of the hard-coded constants with PAGE_SIZE/SHIFT/ORDER where
appropriate.
Likewise, in a couple of places it doesn't make sense to base some
allocations on page size when all that's required is a constant 4K,
etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are potential cases in the future where the IOMMU might be
mapping smaller pages than the regular MMU is using. Keep the
allocator working on MMU pagesizes, but the low-level mapping
functions need to map more than one TCE entry per page to deal with
this.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the implementation-specific parts of include/asm-ppc64/iommu.h
to separate include files (tce.h and dart.h respectively).
The generic iommu code really doesn't care about the underlying
implementation, and the TCE and DART stuff is completely different.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ME, and do not set ctime unless explicitly requested with atime and/or
mtime (it gets thrown away by most servers anyway as there is no way to set
this via posix).
Signed-off-by: Steve French (sfrench@us.ibm.com)
The problem is in the ondemand governor, there is a periodic measurement
of the CPU usage. This CPU usage is updated by the scheduler after every
tick (basically, by adding 1 either to "idle" or to "user" or to
"system"). So if the frequency of the governor is too high, the stat
will be meaningless (as mostly no number have changed).
So this patch checks that the measurements are separated by at least 10
ticks. It means that by default, stats will have about 5% error (20
ticks). Of course those numbers can be argued but, IMHO, they look sane.
The patch also includes a small clean-up to check more explictly the
result of the conversion from ns to µs being null.
Let's note that (on x86) this has never been really needed before 2.6.13
because HZ was always 1000. Now that HZ can be 100, some CPU might be
affected by this problem. For instance when HZ=100, the centrino ,which
has a 10µs transition latency, would lead to the governor allowing to
read stats every tick (10ms)!
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dave Jones <davej@redhat.com>
From: hare@suse.de
for a proper alignment between open-iscsi and iscsitarget the
definitions in include/iscsi_proto.h do not match exactly.
With this patch it's possible to have iscsitarget use
'include/iscsi_proto.h' instead of its own iscsi_hdr.h.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: tomof@acm.org
I'm not sure about this. I don't think that NODELAY option hurts
performance. However, open-iscsi does not use MSG_MORE properly with
sendpage, so NODELAY option hurts the open-iscsi performance.
I've attached a patch to fix NODELAY and MSG_MORE problems and the
write performance results with disktest.
I use Opteron boxes connected directly, Chelsio NICs, 1500-byte MTU,
64 KB I/O size, and the iSCSI parameters on open-iscsi web site.
With only NODELAY fix, the performance drops, as you said. On the
other hand, NODELAY and MSG_MORE fixes improve the performance
overall.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move acpi_map_iosapics() from pci.c to acpi.c, since it doesn't
have anything to do with PCI.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment about how ar.k0 is used. Make the initialization the
same as in start_secondary() (no functional change, just make it look
more similar).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
User mode kexec tools expect to find information about physical
memory in /proc/iomem (as they do on x86) to validate the addresses
that the new kernel will use.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Made the CHRP/PMAC/PREP config options selectable by the user.
This allows us to build kernels specifically for one of the
platforms thus reducing code size.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is a new patch that removes all notion of the pmac, prep,
chrp and openfirmware initialization sections, and then unifies
the sections.h files without those __pmac, etc, sections identifiers
cluttering things up.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We always use the inlined versions of local_irq_enable, local_irq_disable,
local_save_flags_ptr, and local_irq_restore on ppc32 so the non-inlined
versions where just taking up space.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merged ppc_asm.h between ppc32 & ppc64. The majority of the file is
common between the two architectures excluding how a single GPR is
saved/restored and which GPRs are non-volatile.
Additionally, moved the ASM_CONST macro used on ppc64 into ppc_asm.h.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch increases the maximum number of cpus supported on IA64
to 1024. No changes are made to the default SSI size. The patch
simply allows specifying up to 1024p.
There are certainly scaling (& other) issues that also need to be
addressed!!! Additional patches will follow.....
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[PATCH 14/29] Fixed type-o of abg_ture -> abg_true.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
NOTE: This patch requires drivers using abg_ture to be updated.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Switched to sscanf as per friendly comment in store_debug_level.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Removed ieee80211_info_element_hdr structure as ieee80211_info_element
provides the same use.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changed 802.11 headers to use ieee80211_info_element as zero sized
array so that sizeof calculations do not account for IE sizes.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added wireless spy support to Rx code path.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
NOTE: Looks like scripts/Lindent generated output different
than the Lindented version already in-kernel, hence all the
whitespace deltas... *sigh*
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Incorporated Bill Moss' quality scaling algorithm into default wireless
extension handler.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed some endian issues with 802.11 header usage in ieee80211_rx.c
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 01:07:47 2005 -0400
Update PCMCIA ID's.
Intel Pro/Wireless 2011 and 2011B have the same numeric ID, so use
strings instead.
Take all entries from *.conf for Orinoco, HostAP and linux-wlan-ng and
adds them with minimal changes (e.g. we don't need a revision string
after a string that identifies the chipset).
Add comments with card names to all numeric entries. Note: the comments
don't and cannot cover all cards, since the main reason of having
numeric IDs is to cover cards that are often rebranded.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Pavel Roskin <proski@gnu.org>
Date: Fri Sep 16 00:49:05 2005 -0400
Remove conditionals that are useless in the kernel drivers.
Kernel drivers are never compiled against pcmcia-cs headers.
Firmware is never embedded into spectrum_cs module.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don Fry reminded me that the pcnet32_loopback_test() asssumes the ring size
is no less than 4. The minimum ring size was changed to 4 in
pcnet32_set_ringparam() to allow the loopback test to work unchanged.
- Set minimum ring size to 4 to allow loopback test to work unchanged
- Moved variable init_block to first field in struct pcnet32_private
Signed-off-by: Hubert WS Lin <wslin@tw.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the set_ringparam(), one of the ethtool operations,
which allows changing tx/rx ring sizes via ethtool.
- Changed memery allocation of tx/rx ring from static to dynamic
- Implemented set_ringparam()
- Tested on i386 and ppc64
Signed-off-by: Hubert WS Lin <wslin@tw.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
we do not request more than negotiated buffer size even if buffer
size is small (smaller than one page)
Signed-off-by: Steve French (sfrench@us.ibm.com)
Some of the SN code & #defines related to compact nodes & IO discovery
have gotten stale over the years. This patch attempts to clean them up.
Some of the various SN MAX_xxx #defines were also unclear & misused.
The primary changes are:
- use MAX_NUMNODES. This is the generic linux #define for the number
of nodes that are known to the generic kernel. Arrays & loops
for constructs that are 1:1 with linux-defined nodes should
use the linux #define - not an SN equivalent.
- use MAX_COMPACT_NODES for MAX_NUMNODES + NUM_TIOS. This is the
number of nodes in the SSI system. Compact nodes are a hack to
get around the IA64 architectural limit of 256 nodes. Large SGI
systems have more than 256 nodes. When we upgrade to ACPI3.0,
I _hope_ that all nodes will be real nodes that are known to
the generic kernel. That will allow us to delete the notion
of "compact nodes".
- add MAX_NUMALINK_NODES for the total number of nodes that
are in the numalink domain - all partitions.
- simplified (understandable) scan_for_ionodes()
- small amount of cleanup related to cnodes
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
PNP and PNPACPI turned on
i8042 recently changed from ACPI to PNP detection. Without PNP, it
probes legacy I/O ports for the keyboard controller, which causes an
MCA on HP boxes.
Also, I'm about to remove 8250_acpi.c, so we'll need PNP to detect
non-PCI serial ports. Until 8250_acpi.c is removed, some systems
will see serial ports reported twice (once from 8250_acpi.c and again
from 8250_pnp.c). This is harmless.
PNPACPI is still marked EXPERIMENTAL, but I'm not aware of any
outstanding issues on ia64.
IDE_GENERIC turned off (except for SGI simulator, all ia64 IDE is PCI)
ide-generic probes compiled-in legacy I/O ports for IDE devices, which
again causes an MCA. It would be nicer to just get rid of all the
legacy junk from include/asm-ia64/ide.h, but that is a bit riskier
because it could break ide-cs and the HDIO_REGISTER_HWIF ioctl
(http://www.ussg.iu.edu/hypermail/linux/kernel/0508.2/0049.html).
Here's the essence of the patch:
-# CONFIG_PNP is not set
+CONFIG_PNP=y
+CONFIG_PNPACPI=y
-CONFIG_IDE_GENERIC=y
+# CONFIG_IDE_GENERIC is not set
Tested on tiger, bigsur, and zx1.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Machine vector selection has always been a bit of a hack given how
early in system boot it needs to be done. Services like ACPI namespace
are not available and there are non-trivial problems to moving them to
early boot. However, there's no reason we can't change to a different
machvec later in boot when the services we need are available. By
adding a entry point for later initialization of the swiotlb, we can add
an error path for the hpzx1 machevec initialization and fall back to the
DIG machine vector if IOMMU hardware isn't found in the system. Since
ia64 uses 4GB for zone DMA (no ISA support), it's trivial to allocate a
contiguous range from the slab for bounce buffer usage.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Adds an "Ethernet" driver which sends Ethernet packets over the standard
RapidIO messaging. This depends on the core RIO patch for mailbox/doorbell
access.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains possible cleanups including the following:
- make needlessly global code static
- #if 0 the following unused global function:
- sdladrv.c: sdla_intde
- remove the following unused global variable:
- lmc_media.c: lmc_t1_cables
- remove the following unneeded EXPORT_SYMBOL's:
- cycx_drv.c: cycx_inten
- sdladrv.c: sdla_inten
- sdladrv.c: sdla_intde
- sdladrv.c: sdla_intack
- sdladrv.c: sdla_intr
- syncppp.c: sppp_input
- syncppp.c: sppp_change_mtu
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace the custom is_digit()/is_hex_digit() macros with
isdigit()/isxdigit() from <linux/ctype.h> Additionaly remove unused macro
is_alpha() from <linux/wanpipe.h>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Author: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Use new Wireless Extension API for wireless stats.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add support for Radeon PCI Express cards (needs a new X.org DDX)
Also allows PCI GART table to be stored in VRAM for non PCIE cards
Signed-off-by: Dave Airlie <airlied@linux.ie>
Add support for GL_ATI_fragment_shader, new packets R200_EMIT_PP_AFS_0/1,
R200_EMIT_PP_TXCTLALL_0-5 (replaces R200_EMIT_PP_TXFILTER_0-5, 2 more regs)
and R200_EMIT_ATF_TFACTOR (replaces R200_EMIT_TFACTOR_0 (8 consts instead of 6)
From: Roland Scheidegger, David Airlie
Signed-off-by: David Airlie <airlied@linux.ie>
Now it looks like we'll have multiple users of the iscsi transport
class, the iscsi initiator shouldn't really be a dependency of it. This
patch moves iscsi to being an initiator in its own right which selects
the transport attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
netlink_kernel_create now has two new arguments; the module (which is
easy) and the number of groups, which I arbitrarily set to one.
Acked by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New version leaves the original memory map unmodified.
Also saves any granule trimmings for use by the uncached
memory allocator.
Inspired by Khalid Aziz (various traces of his patch still
remain). Fixes to uncached_build_memmap() and sn2 testing
by Martin Hicks.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Resend using accessors instead of volatile qualifiers per hch comments, and
easier to understand convenience macros per rja comments.
Patch to apply volatile semantics when accessing MMR's in various SN files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When XPC is being shutdown (i.e., rmmod, reboot) it doesn't ensure that
other partitions with whom it was connected have completely disengaged
from any attempt at cross-partition memory references. This can lead to
MCAs in any of these other partitions when the partition is reset.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
1) workaround a h/w reset issue
2) to improve the determination of FPGA-based h/w in
the arch/ia64/sn/kernel/tiocx code.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This argument was added in a recent patch, but is unnecessary, since
the superblock is easily obtained from the dentry.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
(Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
also should have been listed on the last cifs patch fixing some lookup
intent handling in cifs)
Signed-off-by: Steve French <sfrench@us.ibm.com>
Make cifs_stats code conditional in the header files to avoid ifdefs in the
main code.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
allows specifying an RFC1001 target "called" name (netbios name of the
server, which can now be pecified as mount option "servernetbiosname"
but will eventually be passed in automatically on retry of host down
error messages caused when server refuses to handle default server
name and can not handle port 445). This is an important step, but
additional testing and fixup is needed to add remaining function needed
for these.
Signed-off-by: Steve French (sfrench@us.ibm.com)
will eventually (or should eventually) be common code for jfs, smbfs,
etc. but in the meantime is small enough and necessary when mounting
case insensitive to Windows (nocase).
Signed-off-by: Shaggy (shaggy@austin.ibm.com)
Signed-off-by: Steve French (sfrench@us.ibm.com)
over the wire (to help the case when applications break with cifs mandatory
lock behavior. Add part one of mount option for requesting case
insensitive path name matching.
Signed-off-by: Steve French (sfrench@us.ibm.com)
03_sil24_add-pci-fault-check.patch
On entry to interrupt handler, PORT_SLOT_STAT register is read
first. Check if PCI fault or device removal has occurred by
testing the value for 0xffffffff.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 6 ++++++
1 files changed, 6 insertions(+)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
02_sil24_remove-irq-disable-on-spurious-intr.patch
If interrupt occurs on a disabled port, the driver used to
mask the port's interrupt, but we don't know if such action is
necessary yet and that's not what other drives do. So, just
do nothing and tell IRQ subsystem that it's not our interrupt.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 15 +++++----------
1 files changed, 5 insertions(+), 10 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/scsi/scsi_transport_iscsi.c: In function `show_transport_handle':
drivers/scsi/scsi_transport_iscsi.c💯 warning: long long unsigned int format, long unsigned int arg (arg 3)
is caused because uint64_t is only unsigned long on a 64 bit platform.
Fix this by casting to unsigned long long.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mtdchar return -EINVAL for seek prior to offset 0 or to beyond the last
byte in the device/partition, similar to various other seek methods,
instead of fixing up to first or last byte.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove useless udelay(100) after status value already read. Poll
for status OK with reduced udelay if not immediate OK status return.
Fix read and compare of 32-bit status value using 16-bit variable.
Include slab.h since kmalloc/kfree are called.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
mtdblock (and other mtd modules that use the mtd_blkdevs interface
between the mtd translation layers and the linux block layer) handles
incorrectly more than 10 devices or 26 partitions in the names passed to
the generic disk layer. This causes the device file names and other
info kept by the generic disk/block layers to have names such as
"mtdblock<". Use integer formatting for device numbers; use "aa-az"
for partitions 27-52, "ba-bz" for 53-78...
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove mtd_blkdevs refs to the no longer functional DEVFS filesystem.
Verified mtdblock continues to work fine via udev with these calls
removed.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Modify Amd/Fujitsu CFI NOR flash primary vendor extension table revision
check to recognize version 1.4. Verified the existing driver can
handle version 1.4 chips without additional info from 1.4 extended table.
Move the primary vendor extension table revision check from common file
to the 3 CFI chip driver files, since the data structures and revisions
handled by those data structures are specific to the chip driver.
Modify the error message printed when the revision is unknown to be a
KERN_ERR instead of WARNING since this will cause mtd to ignore the chip.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
more than 50 (or so) of such long search entries in the directory. FindNext
could send corrupt last byte of resume name when resume key was a few hundred
bytes long file name or longer.
Fixes Samba Bug # 2932
Signed-off-by: Steve French (sfrench@us.ibm.com)
This is rewritten sil24 driver against v2.6.13-rc3.
Rewritten based on driver originally submitted by Silicon Image.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Creating FIFOs to non-Unix servers (with cifs mounts for which sfu option
was specified) now works.
Signed-off-by: Steve French (sfrench@us.ibm.com)
Thanks to Martin Koeppe for his assistance
This should help the case of creating fifos and other special files to
servers which do not support the Unix extensions.
Signed-off-by: Steve French (sfrench@us.ibm.com)
Thanks to Martin Koeppe for his suggestions and good analysis
@@ -42,9 +42,9 @@ bttv uses the PCI Subsystem ID to autodetect the card type. lspci lists
the Subsystem ID in the second line, looks like this:
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 02)
Subsystem: Hauppauge computer works Inc. WinTV/GO
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at e2000000 (32-bit, prefetchable) [size=4K]
Subsystem: Hauppauge computer works Inc. WinTV/GO
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at e2000000 (32-bit, prefetchable) [size=4K]
only bt878-based cards can have a subsystem ID (which does not mean
that every card really has one). bt848 cards can't have a Subsystem
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
