Renesas DTS updates for v6.6
- Add Clocked Serial Interface (CSI) support for the RZ/V2M SoC,
- Add PMIC, RTC, and PWM support for the RZ/G2L, RZ/G2LC, and RZ/V2L
SMARC EVK development boards,
- Add PWM (MTU3a) support for the RZ/G2UL and RZ/Five SoCs,
- Add External interrupt (INTC-EX) support for the R-Car S4-8 SoC,
- Add LED support for the Spider development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: spider-cpu: Add GP LEDs
arm64: dts: renesas: r8a779f0: Add INTC-EX node
arm64: dts: renesas: rzg2ul-smarc: Add support for enabling MTU3
arm64: dts: renesas: r9a07g043: Add MTU3a node
ARM dts: renesas: armadillo800eva: Switch to enable-gpios
arm64: dts: renesas: rzg2lc-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: rzg2lc-smarc-som: Add PHY interrupt support for ETH0
riscv: dts: renesas: Clean up dtbs_check W=1 warning due to empty phy node
arm64: dts: renesas: rzg2lc-smarc: Add support for enabling MTU3
arm64: dts: renesas: rzg2l-smarc: Add support for enabling MTU3
arm64: dts: renesas: Add missing space before {
ARM: dts: renesas: Add missing space before {
arm64: dts: renesas: Minor whitespace cleanup around '='
arm64: dts: renesas: rzg2l-smarc-som: Enable PMIC and built-in RTC
arm64: dts: renesas: r9a09g011: Add CSI nodes
arm64: dts: renesas: rzg2l: Fix txdv-skew-psec typos
arm64: dts: renesas: rzg2l: Update overfow/underflow IRQ names for MTU3 channels
Link: https://lore.kernel.org/r/cover.1690545144.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Without this change the KSZ9477 Evaluation board's Linux (v6.5-rc1) shows
following device warning:
'ksz-switch spi1.0: Port 5 interpreting RGMII delay settings based on "phy-mode" property, please update device tree to specify "rx-internal-delay-ps" and "tx-internal-delay-ps"'
This is not critical, as KSZ driver by itself assigns default value of
tx delay to 2000 ps (as 'rgmii-txid' is set as PHY mode).
However, to avoid extra warnings in logs - the missing 'tx-internal-delay-ps'
has been specified with the default value of 2000 ps.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20230727080656.3828397-1-lukma@denx.de
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Without this change the KSZ9477-EVB board hangs just after passing
execution flow from u-boot to Linux kernel.
This code has been copied from at91-sama5d3_xplained.dts.
Test setup: Linux 6.5-rc1
Config: arch/arm/configs/sama5_defconfig
Toolchain: gcc-linaro-7.3.1-2018.05-x86_64_arm-linux-gnueabi
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20230712152111.3756211-1-lukma@denx.de
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
panel-lvds alone is not a valid compatible string and we always need a
specific compatible string as well. Nexus 7 can come with one of (at
least) two panels, so pick one of them as the specific compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LVDS bindings require a specific compatible string in addition to
the generic "panel-lvds". Add the HannStar HSD101PWW2 which is used on
a similar device (ASUS TF201) and seems to work fine with slightly
modified timings in DT.
Suggested-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating the I2C3 node and adding NVEC specific
properties, reuse the I2C3 node, extend it with NVEC specific properties
and drop properties that are not needed by NVEC. This results in a DTB
that is a bit cleaner and avoids accidentally using I2C3 and NVEC which
would have them fight over the same hardware resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device tree bindings for the Tegra high-speed UART require the
reset-names property, so add it whenever the compatible string for the
serial port is overwritten.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The UART devices found on Tegra chips have a single reset connected to
them, so a reset-names property isn't needed. In fact, the device tree
bindings don't allow this property, so remove them to allow the nodes
to be properly validated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debug UART doesn't support DMA and the DT bindings prohibit the use
of the dmas and dma-names properties for it, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull asm-generic updates from Arnd Bergmann:
"These are cleanups for architecture specific header files:
- the comments in include/linux/syscalls.h have gone out of sync and
are really pointless, so these get removed
- The asm/bitsperlong.h header no longer needs to be architecture
specific on modern compilers, so use a generic version for newer
architectures that use new enough userspace compilers
- A cleanup for virt_to_pfn/virt_to_bus to have proper type checking,
forcing the use of pointers"
* tag 'asm-generic-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
syscalls: Remove file path comments from headers
tools arch: Remove uapi bitsperlong.h of hexagon and microblaze
asm-generic: Unify uapi bitsperlong.h for arm64, riscv and loongarch
m68k/mm: Make pfn accessors static inlines
arm64: memory: Make virt_to_pfn() a static inline
ARM: mm: Make virt_to_pfn() a static inline
asm-generic/page.h: Make pfn accessors static inlines
xen/netback: Pass (void *) to virt_to_page()
netfs: Pass a pointer to virt_to_page()
cifs: Pass a pointer to virt_to_page() in cifsglob
cifs: Pass a pointer to virt_to_page()
riscv: mm: init: Pass a pointer to virt_to_page()
ARC: init: Pass a pointer to virt_to_pfn() in init
m68k: Pass a pointer to virt_to_pfn() virt_to_page()
fs/proc/kcore.c: Pass a pointer to virt_addr_valid()
Pull SoC fixes from Arnd Bergmann:
"There are three small fixes that came up sincie the past week:
- an incorrect bit offset in ixp4xx bus driver
- a riscv randconfig regression in the thead platform I merged
- whitespace fixes for some dts files"
* tag 'soc-fixes-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
ARM: dts: st: add missing space before {
RISC-V: make ARCH_THEAD preclude XIP_KERNEL
Pull crypto updates from Herbert Xu:
"API:
- Add linear akcipher/sig API
- Add tfm cloning (hmac, cmac)
- Add statesize to crypto_ahash
Algorithms:
- Allow only odd e and restrict value in FIPS mode for RSA
- Replace LFSR with SHA3-256 in jitter
- Add interface for gathering of raw entropy in jitter
Drivers:
- Fix race on data_avail and actual data in hwrng/virtio
- Add hash and HMAC support in starfive
- Add RSA algo support in starfive
- Add support for PCI device 0x156E in ccp"
* tag 'v6.5-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (85 commits)
crypto: akcipher - Do not copy dst if it is NULL
crypto: sig - Fix verify call
crypto: akcipher - Set request tfm on sync path
crypto: sm2 - Provide sm2_compute_z_digest when sm2 is disabled
hwrng: imx-rngc - switch to DEFINE_SIMPLE_DEV_PM_OPS
hwrng: st - keep clock enabled while hwrng is registered
hwrng: st - support compile-testing
hwrng: imx-rngc - fix the timeout for init and self check
KEYS: asymmetric: Use new crypto interface without scatterlists
KEYS: asymmetric: Move sm2 code into x509_public_key
KEYS: Add forward declaration in asymmetric-parser.h
crypto: sig - Add interface for sign/verify
crypto: akcipher - Add sync interface without SG lists
crypto: cipher - On clone do crypto_mod_get()
crypto: api - Add __crypto_alloc_tfmgfp
crypto: api - Remove crypto_init_ops()
crypto: rsa - allow only odd e and restrict value in FIPS mode
crypto: geniv - Split geniv out of AEAD Kconfig option
crypto: algboss - Add missing dependency on RNG2
crypto: starfive - Add RSA algo support
...
Pull slab updates from Vlastimil Babka:
- SLAB deprecation:
Following the discussion at LSF/MM 2023 [1] and no objections, the
SLAB allocator is deprecated by renaming the config option (to make
its users notice) to CONFIG_SLAB_DEPRECATED with updated help text.
SLUB should be used instead. Existing defconfigs with CONFIG_SLAB are
also updated.
- SLAB_NO_MERGE kmem_cache flag (Jesper Dangaard Brouer):
There are (very limited) cases where kmem_cache merging is
undesirable, and existing ways to prevent it are hacky. Introduce a
new flag to do that cleanly and convert the existing hacky users.
Btrfs plans to use this for debug kernel builds (that use case is
always fine), networking for performance reasons (that should be very
rare).
- Replace the usage of weak PRNGs (David Keisar Schmidt):
In addition to using stronger RNGs for the security related features,
the code is a bit cleaner.
- Misc code cleanups (SeongJae Parki, Xiongwei Song, Zhen Lei, and
zhaoxinchao)
Link: https://lwn.net/Articles/932201/ [1]
* tag 'slab-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab_common: use SLAB_NO_MERGE instead of negative refcount
mm/slab: break up RCU readers on SLAB_TYPESAFE_BY_RCU example code
mm/slab: add a missing semicolon on SLAB_TYPESAFE_BY_RCU example code
mm/slab_common: reduce an if statement in create_cache()
mm/slab: introduce kmem_cache flag SLAB_NO_MERGE
mm/slab: rename CONFIG_SLAB to CONFIG_SLAB_DEPRECATED
mm/slab: remove HAVE_HARDENED_USERCOPY_ALLOCATOR
mm/slab_common: Replace invocation of weak PRNG
mm/slab: Replace invocation of weak PRNG
slub: Don't read nr_slabs and total_objects directly
slub: Remove slabs_node() function
slub: Remove CONFIG_SMP defined check
slub: Put objects_show() into CONFIG_SLUB_DEBUG enabled block
slub: Correct the error code when slab_kset is NULL
mm/slab: correct return values in comment for _kmem_cache_create()
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly minor cleanups and bugfixes that address harmless
problems.
The largest branch is a conversion of the omap platform to use GPIO
descriptors throughout the tree, for any devices that are not fully
converted to devicetree.
The Samsung Exynos platform gains back support for the Exynos4212 chip
that was previously unused and removed but is now used for the Samsung
Galaxy Tab3"
* tag 'soc-arm-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
ARM: omap2: Fix copy/paste bug
MAINTAINERS: Replace my email address
Input: ads7846 - fix pointer cast warning
Input: ads7846 - Fix usage of match data
ARM: omap2: Fix checkpatch issues
arm: omap1: replace printk() with pr_err macro
ARM: omap: Fix checkpatch issues
ARM: s3c: Switch i2c drivers back to use .probe()
ARM: versatile: mark mmc_status() static
ARM: spear: include "pl080.h" for pl080_get_signal() prototype
ARM: sa1100: address missing prototype warnings
ARM: pxa: fix missing-prototypes warnings
ARM: orion5x: fix d2net gpio initialization
ARM: omap2: fix missing tick_broadcast() prototype
ARM: omap1: add missing include
ARM: lpc32xx: add missing include
ARM: imx: add missing include
ARM: highbank: add missing include
ARM: ep93xx: fix missing-prototype warnings
ARM: davinci: fix davinci_cpufreq_init() declaration
...
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
Pull drm updates from Dave Airlie:
"There is one set of patches to misc for a i915 gsc/mei proxy driver.
Otherwise it's mostly amdgpu/i915/msm, lots of hw enablement and lots
of refactoring.
core:
- replace strlcpy with strscpy
- EDID changes to support further conversion to struct drm_edid
- Move i915 DSC parameter code to common DRM helpers
- Add Colorspace functionality
aperture:
- ignore framebuffers with non-primary devices
fbdev:
- use fbdev i/o helpers
- add Kconfig options for fb_ops helpers
- use new fb io helpers directly in drivers
sysfs:
- export DRM connector ID
scheduler:
- Avoid an infinite loop
ttm:
- store function table in .rodata
- Add query for TTM mem limit
- Add NUMA awareness to pools
- Export ttm_pool_fini()
bridge:
- fsl-ldb: support i.MX6SX
- lt9211, lt9611: remove blanking packets
- tc358768: implement input bus formats, devm cleanups
- ti-snd65dsi86: implement wait_hpd_asserted
- analogix: fix endless probe loop
- samsung-dsim: support swapped clock, fix enabling, support var
clock
- display-connector: Add support for external power supply
- imx: Fix module linking
- tc358762: Support reset GPIO
panel:
- nt36523: Support Lenovo J606F
- st7703: Support Anbernic RG353V-V2
- InnoLux G070ACE-L01 support
- boe-tv101wum-nl6: Improve initialization
- sharp-ls043t1le001: Mode fixes
- simple: BOE EV121WXM-N10-1850, S6D7AA0
- Ampire AM-800480L1TMQW-T00H
- Rocktech RK043FN48H
- Starry himax83102-j02
- Starry ili9882t
amdgpu:
- add new ctx query flag to handle reset better
- add new query/set shadow buffer for rdna3
- DCN 3.2/3.1.x/3.0.x updates
- Enable DC_FP on loongarch
- PCIe fix for RDNA2
- improve DC FAMS/SubVP support for better power management
- partition support for lots of engines
- Take NUMA into account when allocating memory
- Add new DRM_AMDGPU_WERROR config parameter to help with CI
- Initial SMU13 overdrive support
- Add support for new colorspace KMS API
- W=1 fixes
amdkfd:
- Query TTM mem limit rather than hardcoding it
- GC 9.4.3 partition support
- Handle NUMA for partitions
- Add debugger interface for enabling gdb
- Add KFD event age tracking
radeon:
- Fix possible UAF
i915:
- new getparam for PXP support
- GSC/MEI proxy driver
- Meteorlake display enablement
- avoid clearing preallocated framebuffers with TTM
- implement framebuffer mmap support
- Disable sampler indirect state in bindless heap
- Enable fdinfo for GuC backends
- GuC loading and firmware table handling fixes
- Various refactors for multi-tile enablement
- Define MOCS and PAT tables for MTL
- GSC/MEI support for Meteorlake
- PMU multi-tile support
- Large driver kernel doc cleanup
- Allow VRR toggling and arbitrary refresh rates
- Support async flips on linear buffers on display ver 12+
- Expose CRTC CTM property on ILK/SNB/VLV
- New debugfs for display clock frequencies
- Hotplug refactoring
- Display refactoring
- I915_GEM_CREATE_EXT_SET_PAT for Mesa on Meteorlake
- Use large rings for compute contexts
- HuC loading for MTL
- Allow user to set cache at BO creation
- MTL powermanagement enhancements
- Switch to dedicated workqueues to stop using flush_scheduled_work()
- Move display runtime init under display/
- Remove 10bit gamma on desktop gen3 parts, they don't support it
habanalabs:
- uapi: return 0 for user queries if there was a h/w or f/w error
- Add pci health check when we lose connection with the firmware.
This can be used to distinguish between pci link down and firmware
getting stuck.
- Add more info to the error print when TPC interrupt occur.
- Firmware fixes
msm:
- Adreno A660 bindings
- SM8350 MDSS bindings fix
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer
platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x,
sc8280xp, sm8450
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Added support for display controller on MSM8226 platform
- A690 GPU support
- Move cmdstream dumping out of fence signaling path
- a610 support
- Support for a6xx devices without GMU
nouveau:
- NULL ptr before deref fixes
armada:
- implement fbdev emulation as client
sun4i:
- fix mipi-dsi dotclock
- release clocks
vc4:
- rgb range toggle property
- BT601 / BT2020 HDMI support
vkms:
- convert to drmm helpers
- add reflection and rotation support
- fix rgb565 conversion
gma500:
- fix iomem access
shmobile:
- support renesas soc platform
- enable fbdev
mxsfb:
- Add support for i.MX93 LCDIF
stm:
- dsi: Use devm_ helper
- ltdc: Fix potential invalid pointer deref
renesas:
- Group drivers in renesas subdirectory to prepare for new platform
- Drop deprecated R-Car H3 ES1.x support
meson:
- Add support for MIPI DSI displays
virtio:
- add sync object support
mediatek:
- Add display binding document for MT6795"
* tag 'drm-next-2023-06-29' of git://anongit.freedesktop.org/drm/drm: (1791 commits)
drm/i915: Fix a NULL vs IS_ERR() bug
drm/i915: make i915_drm_client_fdinfo() reference conditional again
drm/i915/huc: Fix missing error code in intel_huc_init()
drm/i915/gsc: take a wakeref for the proxy-init-completion check
drm/msm/a6xx: Add A610 speedbin support
drm/msm/a6xx: Add A619_holi speedbin support
drm/msm/a6xx: Use adreno_is_aXYZ macros in speedbin matching
drm/msm/a6xx: Use "else if" in GPU speedbin rev matching
drm/msm/a6xx: Fix some A619 tunables
drm/msm/a6xx: Add A610 support
drm/msm/a6xx: Add support for A619_holi
drm/msm/adreno: Disable has_cached_coherent in GMU wrapper configurations
drm/msm/a6xx: Introduce GMU wrapper support
drm/msm/a6xx: Move CX GMU power counter enablement to hw_init
drm/msm/a6xx: Extend and explain UBWC config
drm/msm/a6xx: Remove both GBIF and RBBM GBIF halt on hw init
drm/msm/a6xx: Add a helper for software-resetting the GPU
drm/msm/a6xx: Improve a6xx_bus_clear_pending_transactions()
drm/msm/a6xx: Move a6xx_bus_clear_pending_transactions to a6xx_gpu
drm/msm/a6xx: Move force keepalive vote removal to a6xx_gmu_force_off()
...
Pull gpio updates from Bartosz Golaszewski:
"We have two new drivers, some improvements to the core code, lots of
different updates to existing GPIO drivers and some dt-bindings on
top.
There's nothing controversial in here and almost everything has been
in next for more than a week (95% a lot longer than this). The only
thing that has spent less time in next is a new driver so no risk of
regressions.
The single merge pulls in changes that remove all usage of global GPIO
numbers from arch/arm/mach-omap.
Core GPIO library:
- remove unused symbols
- don't spam the kernel log with messages about hogs
- remove old sysfs API cruft
- improve handling of GPIO masks
New drivers:
- add a driver for the BlueField-3 GPIO controller
- add GPIO support for the TPS65219 PMIC
Driver improvements:
- extend the gpio-aggregator driver to support ramp-up/ramp-down
delay
- remove unnecessary CONFIG_OF guards from gpio-aggregator
- readability improvements in gpio-tangier
- switch i2c drivers back to using probe() now that it's been
converted in the i2c subsystem to not taking the id parameter
- remove unused inclusions of of_gpio.h in several drivers
- make pm ops static in gpio-davinci and fix a comment
- use more devres in drivers to shrink and simplify the code
- add missing include in gpio-sa1100
- add HAS_IOPORT KConfig dependency where needed
- add permissions checks before accessing pins in gpio-tegra186
- convert the gpio-zynq driver to using immutable irqchips
- preserve output settings set by the bootloader in gpio-mpc8xxx
Selftests:
- tweak the variable naming in script tests
Device tree updates:
- convert gpio-mmio and gpio-stmpe to YAML
- add parsing of GPIO hogs to gpio-vf610
- add bindings for the Cirrus EP93xx GPIO controller
- add gpio-line-names property to the gpio-pca9570 bindings
- extend the binding for x-powers,axp209 with another block"
* tag 'gpio-updates-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (58 commits)
of: unittest: drop assertions for GPIO hog messages
gpiolib: Drop unused domain_ops memeber of GPIO IRQ chip
gpio: synq: remove unused zynq_gpio_irq_reqres/zynq_gpio_irq_relres
dt-bindings: gpio: gpio-vf610: Add parsing of hogs
gpio: lpc18xx: Remove unused of_gpio.h inclusion
gpio: xra1403: Remove unused of_gpio.h inclusion
gpio: mpc8xxx: Remove unused of_gpio.h inclusion
dt-bindings: gpio: Add Cirrus EP93xx
gpio: mpc8xxx: latch GPIOs state on module load when configured as output
selftests: gpio: gpio-sim: Use same variable name for sysfs pathname
gpio: mlxbf3: Add gpio driver support
gpio: delay: Remove duplicative functionality
gpio: aggregator: Set up a parser of delay line parameters
gpio: aggregator: Support delay for setting up individual GPIOs
gpio: aggregator: Remove CONFIG_OF and of_match_ptr() protections
dt-bindings: gpio: pca9570: add gpio-line-names property
gpiolib: remove unused gpio_cansleep()
gpio: tps65219: add GPIO support for TPS65219 PMIC
gpio: zynq: fix zynqmp_gpio not an immutable chip warning
gpio: davinci: make davinci_gpio_dev_pm_ops static
...
This modifies our user mode stack expansion code to always take the
mmap_lock for writing before modifying the VM layout.
It's actually something we always technically should have done, but
because we didn't strictly need it, we were being lazy ("opportunistic"
sounds so much better, doesn't it?) about things, and had this hack in
place where we would extend the stack vma in-place without doing the
proper locking.
And it worked fine. We just needed to change vm_start (or, in the case
of grow-up stacks, vm_end) and together with some special ad-hoc locking
using the anon_vma lock and the mm->page_table_lock, it all was fairly
straightforward.
That is, it was all fine until Ruihan Li pointed out that now that the
vma layout uses the maple tree code, we *really* don't just change
vm_start and vm_end any more, and the locking really is broken. Oops.
It's not actually all _that_ horrible to fix this once and for all, and
do proper locking, but it's a bit painful. We have basically three
different cases of stack expansion, and they all work just a bit
differently:
- the common and obvious case is the page fault handling. It's actually
fairly simple and straightforward, except for the fact that we have
something like 24 different versions of it, and you end up in a maze
of twisty little passages, all alike.
- the simplest case is the execve() code that creates a new stack.
There are no real locking concerns because it's all in a private new
VM that hasn't been exposed to anybody, but lockdep still can end up
unhappy if you get it wrong.
- and finally, we have GUP and page pinning, which shouldn't really be
expanding the stack in the first place, but in addition to execve()
we also use it for ptrace(). And debuggers do want to possibly access
memory under the stack pointer and thus need to be able to expand the
stack as a special case.
None of these cases are exactly complicated, but the page fault case in
particular is just repeated slightly differently many many times. And
ia64 in particular has a fairly complicated situation where you can have
both a regular grow-down stack _and_ a special grow-up stack for the
register backing store.
So to make this slightly more manageable, the bulk of this series is to
first create a helper function for the most common page fault case, and
convert all the straightforward architectures to it.
Thus the new 'lock_mm_and_find_vma()' helper function, which ends up
being used by x86, arm, powerpc, mips, riscv, alpha, arc, csky, hexagon,
loongarch, nios2, sh, sparc32, and xtensa. So we not only convert more
than half the architectures, we now have more shared code and avoid some
of those twisty little passages.
And largely due to this common helper function, the full diffstat of
this series ends up deleting more lines than it adds.
That still leaves eight architectures (ia64, m68k, microblaze, openrisc,
parisc, s390, sparc64 and um) that end up doing 'expand_stack()'
manually because they are doing something slightly different from the
normal pattern. Along with the couple of special cases in execve() and
GUP.
So there's a couple of patches that first create 'locked' helper
versions of the stack expansion functions, so that there's a obvious
path forward in the conversion. The execve() case is then actually
pretty simple, and is a nice cleanup from our old "grow-up stackls are
special, because at execve time even they grow down".
The #ifdef CONFIG_STACK_GROWSUP in that code just goes away, because
it's just more straightforward to write out the stack expansion there
manually, instead od having get_user_pages_remote() do it for us in some
situations but not others and have to worry about locking rules for GUP.
And the final step is then to just convert the remaining odd cases to a
new world order where 'expand_stack()' is called with the mmap_lock held
for reading, but where it might drop it and upgrade it to a write, only
to return with it held for reading (in the success case) or with it
completely dropped (in the failure case).
In the process, we remove all the stack expansion from GUP (where
dropping the lock wouldn't be ok without special rules anyway), and add
it in manually to __access_remote_vm() for ptrace().
Thanks to Adrian Glaubitz and Frank Scheiner who tested the ia64 cases.
Everything else here felt pretty straightforward, but the ia64 rules for
stack expansion are really quite odd and very different from everything
else. Also thanks to Vegard Nossum who caught me getting one of those
odd conditions entirely the wrong way around.
Anyway, I think I want to actually move all the stack expansion code to
a whole new file of its own, rather than have it split up between
mm/mmap.c and mm/memory.c, but since this will have to be backported to
the initial maple tree vma introduction anyway, I tried to keep the
patches _fairly_ minimal.
Also, while I don't think it's valid to expand the stack from GUP, the
final patch in here is a "warn if some crazy GUP user wants to try to
expand the stack" patch. That one will be reverted before the final
release, but it's left to catch any odd cases during the merge window
and release candidates.
Reported-by: Ruihan Li <lrh2000@pku.edu.cn>
* branch 'expand-stack':
gup: add warning if some caller would seem to want stack expansion
mm: always expand the stack with the mmap write lock held
execve: expand new process stack manually ahead of time
mm: make find_extend_vma() fail if write lock not held
powerpc/mm: convert coprocessor fault to lock_mm_and_find_vma()
mm/fault: convert remaining simple cases to lock_mm_and_find_vma()
arm/mm: Convert to using lock_mm_and_find_vma()
riscv/mm: Convert to using lock_mm_and_find_vma()
mips/mm: Convert to using lock_mm_and_find_vma()
powerpc/mm: Convert to using lock_mm_and_find_vma()
arm64/mm: Convert to using lock_mm_and_find_vma()
mm: make the page fault mmap locking killable
mm: introduce new 'lock_mm_and_find_vma()' page fault helper
Pull non-mm updates from Andrew Morton:
- Arnd Bergmann has fixed a bunch of -Wmissing-prototypes in top-level
directories
- Douglas Anderson has added a new "buddy" mode to the hardlockup
detector. It permits the detector to work on architectures which
cannot provide the required interrupts, by having CPUs periodically
perform checks on other CPUs
- Zhen Lei has enhanced kexec's ability to support two crash regions
- Petr Mladek has done a lot of cleanup on the hard lockup detector's
Kconfig entries
- And the usual bunch of singleton patches in various places
* tag 'mm-nonmm-stable-2023-06-24-19-23' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (72 commits)
kernel/time/posix-stubs.c: remove duplicated include
ocfs2: remove redundant assignment to variable bit_off
watchdog/hardlockup: fix typo in config HARDLOCKUP_DETECTOR_PREFER_BUDDY
powerpc: move arch_trigger_cpumask_backtrace from nmi.h to irq.h
devres: show which resource was invalid in __devm_ioremap_resource()
watchdog/hardlockup: define HARDLOCKUP_DETECTOR_ARCH
watchdog/sparc64: define HARDLOCKUP_DETECTOR_SPARC64
watchdog/hardlockup: make HAVE_NMI_WATCHDOG sparc64-specific
watchdog/hardlockup: declare arch_touch_nmi_watchdog() only in linux/nmi.h
watchdog/hardlockup: make the config checks more straightforward
watchdog/hardlockup: sort hardlockup detector related config values a logical way
watchdog/hardlockup: move SMP barriers from common code to buddy code
watchdog/buddy: simplify the dependency for HARDLOCKUP_DETECTOR_PREFER_BUDDY
watchdog/buddy: don't copy the cpumask in watchdog_next_cpu()
watchdog/buddy: cleanup how watchdog_buddy_check_hardlockup() is called
watchdog/hardlockup: remove softlockup comment in touch_nmi_watchdog()
watchdog/hardlockup: in watchdog_hardlockup_check() use cpumask_copy()
watchdog/hardlockup: don't use raw_cpu_ptr() in watchdog_hardlockup_kick()
watchdog/hardlockup: HAVE_NMI_WATCHDOG must implement watchdog_hardlockup_probe()
watchdog/hardlockup: keep kernel.nmi_watchdog sysctl as 0444 if probe fails
...
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
Pull locking updates from Ingo Molnar:
- Introduce cmpxchg128() -- aka. the demise of cmpxchg_double()
The cmpxchg128() family of functions is basically & functionally the
same as cmpxchg_double(), but with a saner interface.
Instead of a 6-parameter horror that forced u128 - u64/u64-halves
layout details on the interface and exposed users to complexity,
fragility & bugs, use a natural 3-parameter interface with u128
types.
- Restructure the generated atomic headers, and add kerneldoc comments
for all of the generic atomic{,64,_long}_t operations.
The generated definitions are much cleaner now, and come with
documentation.
- Implement lock_set_cmp_fn() on lockdep, for defining an ordering when
taking multiple locks of the same type.
This gets rid of one use of lockdep_set_novalidate_class() in the
bcache code.
- Fix raw_cpu_generic_try_cmpxchg() bug due to an unintended variable
shadowing generating garbage code on Clang on certain ARM builds.
* tag 'locking-core-2023-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (43 commits)
locking/atomic: scripts: fix ${atomic}_dec_if_positive() kerneldoc
percpu: Fix self-assignment of __old in raw_cpu_generic_try_cmpxchg()
locking/atomic: treewide: delete arch_atomic_*() kerneldoc
locking/atomic: docs: Add atomic operations to the driver basic API documentation
locking/atomic: scripts: generate kerneldoc comments
docs: scripts: kernel-doc: accept bitwise negation like ~@var
locking/atomic: scripts: simplify raw_atomic*() definitions
locking/atomic: scripts: simplify raw_atomic_long*() definitions
locking/atomic: scripts: split pfx/name/sfx/order
locking/atomic: scripts: restructure fallback ifdeffery
locking/atomic: scripts: build raw_atomic_long*() directly
locking/atomic: treewide: use raw_atomic*_<op>()
locking/atomic: scripts: add trivial raw_atomic*_<op>()
locking/atomic: scripts: factor out order template generation
locking/atomic: scripts: remove leftover "${mult}"
locking/atomic: scripts: remove bogus order parameter
locking/atomic: xtensa: add preprocessor symbols
locking/atomic: x86: add preprocessor symbols
locking/atomic: sparc: add preprocessor symbols
locking/atomic: sh: add preprocessor symbols
...
Pull arm documentation move from Jonathan Corbet:
"Move the Arm architecture documentation under Documentation/arch/.
This brings some order to the documentation directory, declutters the
top-level directory, and makes the documentation organization more
closely match that of the source"
* tag 'docs-arm-move' of git://git.lwn.net/linux:
dt-bindings: Update Documentation/arm references
docs: update some straggling Documentation/arm references
crypto: update some Arm documentation references
mips: update a reference to a moved Arm Document
arm64: Update Documentation/arm references
arm: update in-source documentation references
arm: docs: Move Arm documentation to Documentation/arch/
Pull ARM updates from Russell King:
- lots of build cleanups from Arnd spread throughout the arch/arm tree
- replace strlcpy() with the preferred strscpy()
- use sign_extend32() in the module linker
- drop handle_irq() machine descriptor method
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9315/1: fiq: include asm/mach/irq.h for prototypes
ARM: 9314/1: tcm: move tcm_init() prototype to asm/tcm.h
ARM: 9313/1: vdso: add missing prototypes
ARM: 9312/1: vfp: include asm/neon.h in vfpmodule.c
ARM: 9311/1: decompressor: move function prototypes to misc.h
ARM: 9310/1: xip-kernel: add __inflate_kernel_data prototype
ARM: 9309/1: add missing syscall prototypes
ARM: 9308/1: move setup functions to header
ARM: 9307/1: nommu: include asm/idmap.h
ARM: 9306/1: cacheflush: avoid __flush_anon_page() missing-prototype warning
ARM: 9305/1: add clear/copy_user_highpage declarations
ARM: 9304/1: add prototype for function called only from asm
ARM: 9303/1: kprobes: avoid missing-declaration warnings
ARM: 9302/1: traps: hide unused functions on NOMMU
ARM: 9301/1: dma-mapping: hide unused dma_contiguous_early_fixup function
ARM: 9300/1: Replace all non-returning strlcpy with strscpy
ARM: 9299/1: module: use sign_extend32() to extend the signedness
ARM: 9298/1: Drop custom mdesc->handle_irq()
Pull SMP updates from Thomas Gleixner:
"A large update for SMP management:
- Parallel CPU bringup
The reason why people are interested in parallel bringup is to
shorten the (kexec) reboot time of cloud servers to reduce the
downtime of the VM tenants.
The current fully serialized bringup does the following per AP:
1) Prepare callbacks (allocate, intialize, create threads)
2) Kick the AP alive (e.g. INIT/SIPI on x86)
3) Wait for the AP to report alive state
4) Let the AP continue through the atomic bringup
5) Let the AP run the threaded bringup to full online state
There are two significant delays:
#3 The time for an AP to report alive state in start_secondary()
on x86 has been measured in the range between 350us and 3.5ms
depending on vendor and CPU type, BIOS microcode size etc.
#4 The atomic bringup does the microcode update. This has been
measured to take up to ~8ms on the primary threads depending
on the microcode patch size to apply.
On a two socket SKL server with 56 cores (112 threads) the boot CPU
spends on current mainline about 800ms busy waiting for the APs to
come up and apply microcode. That's more than 80% of the actual
onlining procedure.
This can be reduced significantly by splitting the bringup
mechanism into two parts:
1) Run the prepare callbacks and kick the AP alive for each AP
which needs to be brought up.
The APs wake up, do their firmware initialization and run the
low level kernel startup code including microcode loading in
parallel up to the first synchronization point. (#1 and #2
above)
2) Run the rest of the bringup code strictly serialized per CPU
(#3 - #5 above) as it's done today.
Parallelizing that stage of the CPU bringup might be possible
in theory, but it's questionable whether required surgery
would be justified for a pretty small gain.
If the system is large enough the first AP is already waiting at
the first synchronization point when the boot CPU finished the
wake-up of the last AP. That reduces the AP bringup time on that
SKL from ~800ms to ~80ms, i.e. by a factor ~10x.
The actual gain varies wildly depending on the system, CPU,
microcode patch size and other factors. There are some
opportunities to reduce the overhead further, but that needs some
deep surgery in the x86 CPU bringup code.
For now this is only enabled on x86, but the core functionality
obviously works for all SMP capable architectures.
- Enhancements for SMP function call tracing so it is possible to
locate the scheduling and the actual execution points. That allows
to measure IPI delivery time precisely"
* tag 'smp-core-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
trace,smp: Add tracepoints for scheduling remotelly called functions
trace,smp: Add tracepoints around remotelly called functions
MAINTAINERS: Add CPU HOTPLUG entry
x86/smpboot: Fix the parallel bringup decision
x86/realmode: Make stack lock work in trampoline_compat()
x86/smp: Initialize cpu_primary_thread_mask late
cpu/hotplug: Fix off by one in cpuhp_bringup_mask()
x86/apic: Fix use of X{,2}APIC_ENABLE in asm with older binutils
x86/smpboot/64: Implement arch_cpuhp_init_parallel_bringup() and enable it
x86/smpboot: Support parallel startup of secondary CPUs
x86/smpboot: Implement a bit spinlock to protect the realmode stack
x86/apic: Save the APIC virtual base address
cpu/hotplug: Allow "parallel" bringup up to CPUHP_BP_KICK_AP_STATE
x86/apic: Provide cpu_primary_thread mask
x86/smpboot: Enable split CPU startup
cpu/hotplug: Provide a split up CPUHP_BRINGUP mechanism
cpu/hotplug: Reset task stack state in _cpu_up()
cpu/hotplug: Remove unused state functions
riscv: Switch to hotplug core state synchronization
parisc: Switch to hotplug core state synchronization
...
Pull x86 boot updates from Thomas Gleixner:
"Initialize FPU late.
Right now FPU is initialized very early during boot. There is no real
requirement to do so. The only requirement is to have it done before
alternatives are patched.
That's done in check_bugs() which does way more than what the function
name suggests.
So first rename check_bugs() to arch_cpu_finalize_init() which makes
it clear what this is about.
Move the invocation of arch_cpu_finalize_init() earlier in
start_kernel() as it has to be done before fork_init() which needs to
know the FPU register buffer size.
With those prerequisites the FPU initialization can be moved into
arch_cpu_finalize_init(), which removes it from the early and fragile
part of the x86 bringup"
* tag 'x86-boot-2023-06-26' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mem_encrypt: Unbreak the AMD_MEM_ENCRYPT=n build
x86/fpu: Move FPU initialization into arch_cpu_finalize_init()
x86/fpu: Mark init functions __init
x86/fpu: Remove cpuinfo argument from init functions
x86/init: Initialize signal frame size late
init, x86: Move mem_encrypt_init() into arch_cpu_finalize_init()
init: Invoke arch_cpu_finalize_init() earlier
init: Remove check_bugs() leftovers
um/cpu: Switch to arch_cpu_finalize_init()
sparc/cpu: Switch to arch_cpu_finalize_init()
sh/cpu: Switch to arch_cpu_finalize_init()
mips/cpu: Switch to arch_cpu_finalize_init()
m68k/cpu: Switch to arch_cpu_finalize_init()
loongarch/cpu: Switch to arch_cpu_finalize_init()
ia64/cpu: Switch to arch_cpu_finalize_init()
ARM: cpu: Switch to arch_cpu_finalize_init()
x86/cpu: Switch to arch_cpu_finalize_init()
init: Provide arch_cpu_finalize_init()
arm has an additional check for address < FIRST_USER_ADDRESS before
expanding the stack. Since FIRST_USER_ADDRESS is defined everywhere
(generally as 0), move that check to the generic expand_downwards().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why
Generic:
- Avoid setting page table entries pointing to a deleted memslot if a
host page table entry is changed concurrently with the deletion"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid illegal stage2 mapping on invalid memory slot
KVM: arm64: Use raw_smp_processor_id() in kvm_pmu_probe_armpmu()
KVM: arm64: Restore GICv2-on-GICv3 functionality
KVM: arm64: PMU: Don't overwrite PMUSERENR with vcpu loaded
KVM: arm64: PMU: Restore the host's PMUSERENR_EL0
KVM/arm64 fixes for 6.4, take #4
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
Memory controller drivers for v6.5
1. Renesas RPC IF: correct the Strobe Timing Adjustment.
2. Broadcom DPFE: fix smatch warning for testing array offset after use.
3. Atmel SDRAMC: drop driver because it was just a wrapper over enabling
clock which is not handled by its clock controller.
4. Minor bindings cleanup.
* tag 'memory-controller-drv-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory-controllers: drop unneeded quotes
memory: atmel-sdramc: remove the driver
memory: brcmstb_dpfe: fix testing array offset after use
memory: renesas-rpc-if: Fix PHYCNT.STRTIM setting
Link: https://lore.kernel.org/r/20230612175508.288775-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The unit address needs to be changed to match the reg property:
arch/arm/boot/dts/marvell/armada-390-db.dts:84.10-106.4: Warning (spi_bus_reg): /soc/spi@10680/flash@1: SPI bus unit address format error, expected "0"
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: Move .dts files to vendor sub-directories
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
* tag 'arm-dts-mv-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
Link: https://lore.kernel.org/r/20230621185025.GA3197738-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In preparation to move Arm .dts files into sub-directories grouped
by vendor/family, the current flat tree of DTBs generated by
dtbs_install needs to be maintained. Moving the installed DTBs to
sub-directories would break various consumers using 'make dtbs_install'.
This is a NOP until sub-directories are introduced.
Signed-off-by: Rob Herring <robh@kernel.org>
Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation to move .dts files into subdirectories, include
sunxi-h3-h5-emlid-neutis.dtsi from the current directory rather than the
symlinked include path.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
AT91 DT for 6.5 #2
It contains:
- generic names for shutdown controller nodes
- enablement of DT overlay support for some AT91 boards
- fix reset and SPI CS for lan966x-kontron-kswitch-d10-mmt based boards
- addition of PHY interrupts for lan966x-kontron-kswitch-d10-mmt-8g
board
* tag 'at91-dt-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
ARM: dts: at91: use generic name for shutdown controller
Link: https://lore.kernel.org/r/20230621093853.1575312-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
MFD_RK808 got split into an I2C and SPI part named MFD_RK8XX_I2C and
MFD_RK8XX_SPI. Since there are no known ARMv7 boards using the SPI
connected RK8XX chips (which are new), it is enough to just enable
the I2C option.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: c20e8c5b12 ("mfd: rk808: Split into core and i2c")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
