net: rnpgbe: Add register_netdev

Complete the network device (netdev) registration flow for Mucse Gbe
Ethernet chips, including:
1. Hardware state initialization:
   - Send powerup notification to firmware (via echo_fw_status)
   - Sync with firmware
   - Reset hardware
2. MAC address handling:
   - Retrieve permanent MAC from firmware (via mucse_mbx_get_macaddr)
   - Fallback to random valid MAC (eth_random_addr) if not valid mac
     from Fw

Signed-off-by: Dong Yibo <dong100@mucse.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251101013849.120565-6-dong100@mucse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/mucse/rnpgbe/rnpgbe.h

@@ -26,18 +26,37 @@ struct mucse_mbx_info {
 	u32 fwpf_ctrl_base;
 };
 
+/* Enum for firmware notification modes,
+ * more modes (e.g., portup, link_report) will be added in future
+ **/
+enum {
+	mucse_fw_powerup,
+};
+
 struct mucse_hw {
 	void __iomem *hw_addr;
+	struct pci_dev *pdev;
 	struct mucse_mbx_info mbx;
+	int port;
 	u8 pfvfnum;
 };
 
+struct mucse_stats {
+	u64 tx_dropped;
+};
+
 struct mucse {
 	struct net_device *netdev;
 	struct pci_dev *pdev;
 	struct mucse_hw hw;
+	struct mucse_stats stats;
 };
 
+int rnpgbe_get_permanent_mac(struct mucse_hw *hw, u8 *perm_addr);
+int rnpgbe_reset_hw(struct mucse_hw *hw);
+int rnpgbe_send_notify(struct mucse_hw *hw,
+		       bool enable,
+		       int mode);
 int rnpgbe_init_hw(struct mucse_hw *hw, int board_type);
 
 /* Device IDs */
@@ -46,4 +65,7 @@ int rnpgbe_init_hw(struct mucse_hw *hw, int board_type);
 #define RNPGBE_DEVICE_ID_N500_DUAL_PORT   0x8318
 #define RNPGBE_DEVICE_ID_N210             0x8208
 #define RNPGBE_DEVICE_ID_N210L            0x820a
+
+#define mucse_hw_wr32(hw, reg, val) \
+	writel((val), (hw)->hw_addr + (reg))
 #endif /* _RNPGBE_H */

drivers/net/ethernet/mucse/rnpgbe/rnpgbe_chip.c

@@ -1,11 +1,82 @@
 // SPDX-License-Identifier: GPL-2.0
 /* Copyright(c) 2020 - 2025 Mucse Corporation. */
 
+#include <linux/pci.h>
 #include <linux/errno.h>
+#include <linux/etherdevice.h>
 
 #include "rnpgbe.h"
 #include "rnpgbe_hw.h"
 #include "rnpgbe_mbx.h"
+#include "rnpgbe_mbx_fw.h"
+
+/**
+ * rnpgbe_get_permanent_mac - Get permanent mac
+ * @hw: hw information structure
+ * @perm_addr: pointer to store perm_addr
+ *
+ * rnpgbe_get_permanent_mac tries to get mac from hw
+ *
+ * Return: 0 on success, negative errno on failure
+ **/
+int rnpgbe_get_permanent_mac(struct mucse_hw *hw, u8 *perm_addr)
+{
+	struct device *dev = &hw->pdev->dev;
+	int err;
+
+	err = mucse_mbx_get_macaddr(hw, hw->pfvfnum, perm_addr, hw->port);
+	if (err) {
+		dev_err(dev, "Failed to get MAC from FW %d\n", err);
+		return err;
+	}
+
+	if (!is_valid_ether_addr(perm_addr)) {
+		dev_err(dev, "Failed to get valid MAC from FW\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * rnpgbe_reset_hw - Do a hardware reset
+ * @hw: hw information structure
+ *
+ * rnpgbe_reset_hw calls fw to do a hardware
+ * reset, and cleans some regs to default.
+ *
+ * Return: 0 on success, negative errno on failure
+ **/
+int rnpgbe_reset_hw(struct mucse_hw *hw)
+{
+	mucse_hw_wr32(hw, RNPGBE_DMA_AXI_EN, 0);
+	return mucse_mbx_reset_hw(hw);
+}
+
+/**
+ * rnpgbe_send_notify - Echo fw status
+ * @hw: hw information structure
+ * @enable: true or false status
+ * @mode: status mode
+ *
+ * Return: 0 on success, negative errno on failure
+ **/
+int rnpgbe_send_notify(struct mucse_hw *hw,
+		       bool enable,
+		       int mode)
+{
+	int err;
+	/* Keep switch struct to support more modes in the future */
+	switch (mode) {
+	case mucse_fw_powerup:
+		err = mucse_mbx_powerup(hw, enable);
+		break;
+	default:
+		err = -EINVAL;
+	}
+
+	return err;
+}
 
 /**
  * rnpgbe_init_n500 - Setup n500 hw info
@@ -50,6 +121,8 @@ int rnpgbe_init_hw(struct mucse_hw *hw, int board_type)
 {
 	struct mucse_mbx_info *mbx = &hw->mbx;
 
+	hw->port = 0;
+
 	mbx->pf2fw_mbx_ctrl = MUCSE_GBE_PFFW_MBX_CTRL_OFFSET;
 	mbx->fwpf_mbx_mask = MUCSE_GBE_FWPF_MBX_MASK_OFFSET;
 

drivers/net/ethernet/mucse/rnpgbe/rnpgbe_hw.h

@@ -11,5 +11,7 @@
 #define MUCSE_N210_FWPF_CTRL_BASE      0x29400
 #define MUCSE_N210_FWPF_SHM_BASE       0x2d900
 
+#define RNPGBE_DMA_AXI_EN              0x0010
+
 #define RNPGBE_MAX_QUEUES 8
 #endif /* _RNPGBE_HW_H */

drivers/net/ethernet/mucse/rnpgbe/rnpgbe_main.c

@@ -7,6 +7,7 @@
 
 #include "rnpgbe.h"
 #include "rnpgbe_hw.h"
+#include "rnpgbe_mbx_fw.h"
 
 static const char rnpgbe_driver_name[] = "rnpgbe";
 
@@ -24,6 +25,58 @@ static struct pci_device_id rnpgbe_pci_tbl[] = {
 	{0, },
 };
 
+/**
+ * rnpgbe_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP).
+ *
+ * Return: 0
+ **/
+static int rnpgbe_open(struct net_device *netdev)
+{
+	return 0;
+}
+
+/**
+ * rnpgbe_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS.
+ *
+ * Return: 0, this is not allowed to fail
+ **/
+static int rnpgbe_close(struct net_device *netdev)
+{
+	return 0;
+}
+
+/**
+ * rnpgbe_xmit_frame - Send a skb to driver
+ * @skb: skb structure to be sent
+ * @netdev: network interface device structure
+ *
+ * Return: NETDEV_TX_OK
+ **/
+static netdev_tx_t rnpgbe_xmit_frame(struct sk_buff *skb,
+				     struct net_device *netdev)
+{
+	struct mucse *mucse = netdev_priv(netdev);
+
+	dev_kfree_skb_any(skb);
+	mucse->stats.tx_dropped++;
+
+	return NETDEV_TX_OK;
+}
+
+static const struct net_device_ops rnpgbe_netdev_ops = {
+	.ndo_open       = rnpgbe_open,
+	.ndo_stop       = rnpgbe_close,
+	.ndo_start_xmit = rnpgbe_xmit_frame,
+};
+
 /**
  * rnpgbe_add_adapter - Add netdev for this pci_dev
  * @pdev: PCI device information structure
@@ -39,10 +92,11 @@ static int rnpgbe_add_adapter(struct pci_dev *pdev,
 			      int board_type)
 {
 	struct net_device *netdev;
+	u8 perm_addr[ETH_ALEN];
 	void __iomem *hw_addr;
 	struct mucse *mucse;
 	struct mucse_hw *hw;
-	int err;
+	int err, err_notify;
 
 	netdev = alloc_etherdev_mq(sizeof(struct mucse), RNPGBE_MAX_QUEUES);
 	if (!netdev)
@@ -64,14 +118,67 @@ static int rnpgbe_add_adapter(struct pci_dev *pdev,
 	}
 
 	hw->hw_addr = hw_addr;
+	hw->pdev = pdev;
+
 	err = rnpgbe_init_hw(hw, board_type);
 	if (err) {
 		dev_err(&pdev->dev, "Init hw err %d\n", err);
 		goto err_free_net;
 	}
+	/* Step 1: Send power-up notification to firmware (no response expected)
+	 * This informs firmware to initialize hardware power state, but
+	 * firmware only acknowledges receipt without returning data. Must be
+	 * done before synchronization as firmware may be in low-power idle
+	 * state initially.
+	 */
+	err_notify = rnpgbe_send_notify(hw, true, mucse_fw_powerup);
+	if (err_notify) {
+		dev_warn(&pdev->dev, "Send powerup to hw failed %d\n",
+			 err_notify);
+		dev_warn(&pdev->dev, "Maybe low performance\n");
+	}
+	/* Step 2: Synchronize mailbox communication with firmware (requires
+	 * response) After power-up, confirm firmware is ready to process
+	 * requests with responses. This ensures subsequent request/response
+	 * interactions work reliably.
+	 */
+	err = mucse_mbx_sync_fw(hw);
+	if (err) {
+		dev_err(&pdev->dev, "Sync fw failed! %d\n", err);
+		goto err_powerdown;
+	}
+
+	netdev->netdev_ops = &rnpgbe_netdev_ops;
+	err = rnpgbe_reset_hw(hw);
+	if (err) {
+		dev_err(&pdev->dev, "Hw reset failed %d\n", err);
+		goto err_powerdown;
+	}
+
+	err = rnpgbe_get_permanent_mac(hw, perm_addr);
+	if (!err) {
+		eth_hw_addr_set(netdev, perm_addr);
+	} else if (err == -EINVAL) {
+		dev_warn(&pdev->dev, "Using random MAC\n");
+		eth_hw_addr_random(netdev);
+	} else if (err) {
+		dev_err(&pdev->dev, "get perm_addr failed %d\n", err);
+		goto err_powerdown;
+	}
+
+	err = register_netdev(netdev);
+	if (err)
+		goto err_powerdown;
 
 	return 0;
-
+err_powerdown:
+	/* notify powerdown only powerup ok */
+	if (!err_notify) {
+		err_notify = rnpgbe_send_notify(hw, false, mucse_fw_powerup);
+		if (err_notify)
+			dev_warn(&pdev->dev, "Send powerdown to hw failed %d\n",
+				 err_notify);
+	}
 err_free_net:
 	free_netdev(netdev);
 	return err;
@@ -138,11 +245,17 @@ err_disable_dev:
 static void rnpgbe_rm_adapter(struct pci_dev *pdev)
 {
 	struct mucse *mucse = pci_get_drvdata(pdev);
+	struct mucse_hw *hw = &mucse->hw;
 	struct net_device *netdev;
+	int err;
 
 	if (!mucse)
 		return;
 	netdev = mucse->netdev;
+	unregister_netdev(netdev);
+	err = rnpgbe_send_notify(hw, false, mucse_fw_powerup);
+	if (err)
+		dev_warn(&pdev->dev, "Send powerdown to hw failed %d\n", err);
 	free_netdev(netdev);
 }
 
@@ -173,6 +286,8 @@ static void rnpgbe_dev_shutdown(struct pci_dev *pdev)
 
 	rtnl_lock();
 	netif_device_detach(netdev);
+	if (netif_running(netdev))
+		rnpgbe_close(netdev);
 	rtnl_unlock();
 	pci_disable_device(pdev);
 }