mirror of
https://github.com/torvalds/linux.git
synced 2025-12-07 20:06:24 +00:00
0ec946d32e
The dwc3 controller present on Apple Silicon SoCs like the M1 requires a specific order of operations synchronized between its PHY and its Type-C controller. Specifically, the PHY first has to go through initial bringup (which requires knowledge of the lane mode and orientation) before dwc3 itself can be brought up and can then finalize the PHY configuration. Additionally, dwc3 has to be teared down and re-initialized whenever the cable is changed due to hardware quirks that prevent a new device from being recognized and due to the PHY being unable to switch lane mode or orientation while dwc3 is up and running. These controllers also have a Apple-specific MMIO region after the common dwc3 region where some controls have to be updated. PHY bringup and shutdown also requires SUSPHY to be enabled for the ports to work correctly. In the future, this driver will also gain support for USB3-via-USB4 tunneling which will require additional tweaks. Add a glue driver that takes of all of these constraints. Reviewed-by: Neal Gompa <neal@gompa.dev> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Signed-off-by: Sven Peter <sven@kernel.org> Link: https://patch.msgid.link/20251015-b4-aplpe-dwc3-v2-5-cbd65a2d511a@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
215 lines
6.3 KiB
Plaintext
215 lines
6.3 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
|
|
config USB_DWC3
|
|
tristate "DesignWare USB3 DRD Core Support"
|
|
depends on (USB || USB_GADGET) && HAS_DMA
|
|
depends on (EXTCON || EXTCON=n)
|
|
select USB_XHCI_PLATFORM if USB_XHCI_HCD
|
|
select USB_ROLE_SWITCH if USB_DWC3_DUAL_ROLE
|
|
help
|
|
Say Y or M here if your system has a Dual Role SuperSpeed
|
|
USB controller based on the DesignWare USB3 IP Core.
|
|
|
|
If you choose to build this driver as a dynamically linked
|
|
module, the module will be called dwc3.ko.
|
|
|
|
if USB_DWC3
|
|
|
|
config USB_DWC3_ULPI
|
|
bool "Register ULPI PHY Interface"
|
|
depends on USB_ULPI_BUS=y || USB_ULPI_BUS=USB_DWC3
|
|
help
|
|
Select this if you have ULPI type PHY attached to your DWC3
|
|
controller.
|
|
|
|
choice
|
|
prompt "DWC3 Mode Selection"
|
|
default USB_DWC3_DUAL_ROLE if (USB && USB_GADGET)
|
|
default USB_DWC3_HOST if (USB && !USB_GADGET)
|
|
default USB_DWC3_GADGET if (!USB && USB_GADGET)
|
|
|
|
config USB_DWC3_HOST
|
|
bool "Host only mode"
|
|
depends on USB=y || USB=USB_DWC3
|
|
help
|
|
Select this when you want to use DWC3 in host mode only,
|
|
thereby the gadget feature will be regressed.
|
|
|
|
config USB_DWC3_GADGET
|
|
bool "Gadget only mode"
|
|
depends on USB_GADGET=y || USB_GADGET=USB_DWC3
|
|
help
|
|
Select this when you want to use DWC3 in gadget mode only,
|
|
thereby the host feature will be regressed.
|
|
|
|
config USB_DWC3_DUAL_ROLE
|
|
bool "Dual Role mode"
|
|
depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3))
|
|
help
|
|
This is the default mode of working of DWC3 controller where
|
|
both host and gadget features are enabled.
|
|
|
|
endchoice
|
|
|
|
comment "Platform Glue Driver Support"
|
|
|
|
config USB_DWC3_OMAP
|
|
tristate "Texas Instruments OMAP5 and similar Platforms"
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
|
depends on EXTCON || !EXTCON
|
|
depends on OF
|
|
default USB_DWC3
|
|
help
|
|
Some platforms from Texas Instruments like OMAP5, DRA7xxx and
|
|
AM437x use this IP for USB2/3 functionality.
|
|
|
|
Say 'Y' or 'M' here if you have one such device
|
|
|
|
config USB_DWC3_EXYNOS
|
|
tristate "Samsung Exynos SoC Platform"
|
|
depends on (ARCH_EXYNOS || COMPILE_TEST) && OF
|
|
default USB_DWC3
|
|
help
|
|
Recent Samsung Exynos SoCs (Exynos5250, Exynos5410, Exynos542x,
|
|
Exynos5800, Exynos5433, Exynos7) ship with one DesignWare Core USB3
|
|
IP inside, say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_PCI
|
|
tristate "PCIe-based Platforms"
|
|
depends on USB_PCI && ACPI
|
|
default USB_DWC3
|
|
help
|
|
If you're using the DesignWare Core IP with a PCIe (but not HAPS
|
|
platform), please say 'Y' or 'M' here.
|
|
|
|
config USB_DWC3_HAPS
|
|
tristate "Synopsys PCIe-based HAPS Platforms"
|
|
depends on USB_PCI
|
|
default USB_DWC3
|
|
help
|
|
If you're using the DesignWare Core IP with a Synopsys PCIe HAPS
|
|
platform, please say 'Y' or 'M' here.
|
|
|
|
config USB_DWC3_KEYSTONE
|
|
tristate "Texas Instruments Keystone2/AM654 Platforms"
|
|
depends on ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
|
|
default USB_DWC3
|
|
help
|
|
Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
|
|
Say 'Y' or 'M' here if you have one such device
|
|
|
|
config USB_DWC3_MESON_G12A
|
|
tristate "Amlogic Meson G12A Platforms"
|
|
depends on OF && COMMON_CLK
|
|
depends on ARCH_MESON || COMPILE_TEST
|
|
default USB_DWC3
|
|
select USB_ROLE_SWITCH
|
|
select REGMAP_MMIO
|
|
help
|
|
Support USB2/3 functionality in Amlogic G12A platforms.
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_OF_SIMPLE
|
|
tristate "Generic OF Simple Glue Layer"
|
|
depends on OF && COMMON_CLK
|
|
default USB_DWC3
|
|
help
|
|
Support USB2/3 functionality in simple SoC integrations.
|
|
Currently supports Xilinx and Qualcomm DWC USB3 IP.
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_ST
|
|
tristate "STMicroelectronics Platforms"
|
|
depends on (ARCH_STI || COMPILE_TEST) && OF
|
|
default USB_DWC3
|
|
help
|
|
STMicroelectronics SoCs with one DesignWare Core USB3 IP
|
|
inside (i.e. STiH407).
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_QCOM
|
|
tristate "Qualcomm Platform"
|
|
depends on ARCH_QCOM || COMPILE_TEST
|
|
depends on EXTCON || !EXTCON
|
|
depends on OF
|
|
default USB_DWC3
|
|
help
|
|
Some Qualcomm SoCs use DesignWare Core IP for USB2/3
|
|
functionality.
|
|
This driver also handles Qscratch wrapper which is needed
|
|
for peripheral mode support.
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_IMX8MP
|
|
tristate "NXP iMX8MP Platform"
|
|
depends on OF && COMMON_CLK
|
|
depends on (ARCH_MXC && ARM64) || COMPILE_TEST
|
|
default USB_DWC3
|
|
help
|
|
NXP iMX8M Plus SoC use DesignWare Core IP for USB2/3
|
|
functionality.
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_XILINX
|
|
tristate "Xilinx Platforms"
|
|
depends on (ARCH_ZYNQMP || COMPILE_TEST) && OF
|
|
default USB_DWC3
|
|
help
|
|
Support Xilinx SoCs with DesignWare Core USB3 IP.
|
|
This driver handles ZynqMP SoC operations.
|
|
Say 'Y' or 'M' if you have one such device.
|
|
|
|
config USB_DWC3_AM62
|
|
tristate "Texas Instruments AM62 Platforms"
|
|
depends on ARCH_K3 || COMPILE_TEST
|
|
default USB_DWC3
|
|
help
|
|
Support TI's AM62 platforms with DesignWare Core USB3 IP.
|
|
The Designware Core USB3 IP is programmed to operate in
|
|
in USB 2.0 mode only.
|
|
Say 'Y' or 'M' here if you have one such device
|
|
|
|
config USB_DWC3_OCTEON
|
|
tristate "Cavium Octeon Platforms"
|
|
depends on CAVIUM_OCTEON_SOC || COMPILE_TEST
|
|
default USB_DWC3
|
|
help
|
|
Support Cavium Octeon platforms with DesignWare Core USB3 IP.
|
|
Only the host mode is currently supported.
|
|
Say 'Y' or 'M' here if you have one such device.
|
|
|
|
config USB_DWC3_RTK
|
|
tristate "Realtek DWC3 Platform Driver"
|
|
depends on OF && ARCH_REALTEK
|
|
default USB_DWC3
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
RTK DHC RTD SoCs with DesignWare Core USB3 IP inside,
|
|
and IP Core configured for USB 2.0 and USB 3.0 in host
|
|
or dual-role mode.
|
|
Say 'Y' or 'M' if you have such device.
|
|
|
|
config USB_DWC3_GENERIC_PLAT
|
|
tristate "DWC3 Generic Platform Driver"
|
|
depends on OF && COMMON_CLK
|
|
default USB_DWC3
|
|
help
|
|
Support USB3 functionality in simple SoC integrations.
|
|
Currently supports SpacemiT DWC USB3. Platforms using
|
|
dwc3-of-simple can easily switch to dwc3-generic by flattening
|
|
the dwc3 child node in the device tree.
|
|
Say 'Y' or 'M' here if your platform integrates DWC3 in a similar way.
|
|
|
|
config USB_DWC3_APPLE
|
|
tristate "Apple Silicon DWC3 Platform Driver"
|
|
depends on OF && ARCH_APPLE
|
|
default USB_DWC3
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
Support Apple Silicon SoCs with DesignWare Core USB3 IP.
|
|
The DesignWare Core USB3 IP has to be used in dual-role
|
|
mode on these machines.
|
|
Say 'Y' or 'M' if you have such device.
|
|
|
|
endif
|