Pull USB fixes from Greg KH:
"Here are some small USB fixes that resolve some reported problems.
These include:
- gadget driver fixes
- dwc3 driver fix
- typec driver fix
- MAINTAINERS file update.
All of these have been in linux-next with no reported problems"
* tag 'usb-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: ucsi: Don't attempt to resume the ports before they exist
usb: gadget: udc: do not clear gadget driver.bus
usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
usb: dwc3: qcom: enable vbus override when in OTG dr-mode
MAINTAINERS: Add myself as UVC Gadget Maintainer
Pull tty/serial driver fixes from Greg KH:
"Here are some small serial and vt fixes. These include:
- 8250 driver fixes relating to dma issues
- stm32 serial driver fix for threaded irqs
- vc_screen bugfix for reported problems.
All have been in linux-next for a while with no reported problems"
* tag 'tty-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
serial: 8250_dma: Fix DMA Rx rearm race
serial: 8250_dma: Fix DMA Rx completion race
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc/whatever driver fixes. They
include:
- IIO driver fixes for some reported problems
- nvmem driver fixes
- fpga driver fixes
- debugfs memory leak fix in the hv_balloon and irqdomain code
(irqdomain change was acked by the maintainer)
All have been in linux-next with no reported problems"
* tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
HV: hv_balloon: fix memory leak with using debugfs_lookup()
nvmem: qcom-spmi-sdam: fix module autoloading
nvmem: core: fix return value
nvmem: core: fix cell removal on error
nvmem: core: fix device node refcounting
nvmem: core: fix registration vs use race
nvmem: core: fix cleanup after dev_set_name()
nvmem: core: remove nvmem_config wp_gpio
nvmem: core: initialise nvmem->id early
nvmem: sunxi_sid: Always use 32-bit MMIO reads
nvmem: brcm_nvram: Add check for kzalloc
iio: imu: fxos8700: fix MAGN sensor scale and unit
iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
iio: imu: fxos8700: fix failed initialization ODR mode assignment
iio: imu: fxos8700: fix incorrect ODR mode readback
iio: light: cm32181: Fix PM support on system with 2 I2C resources
iio: hid: fix the retval in gyro_3d_capture_sample
iio: hid: fix the retval in accel_3d_capture_sample
iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
...
Pull fbdev fixes from Helge Deller:
- fix fbcon to prevent fonts bigger than 32x32 pixels to avoid
overflows reported by syzbot
- switch omapfb to use kstrtobool()
- switch some fbdev drivers to use the backlight helpers
* tag 'fbdev-for-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbcon: Check font dimension limits
fbdev: omapfb: Use kstrtobool() instead of strtobool()
fbdev: fbmon: fix function name in kernel-doc
fbdev: atmel_lcdfb: Rework backlight status updates
fbdev: riva: Use backlight helper
fbdev: omapfb: panel-dsi-cm: Use backlight helper
fbdev: nvidia: Use backlight helper
fbdev: mx3fb: Use backlight helper
fbdev: radeon: Use backlight helper
fbdev: atyfb: Use backlight helper
fbdev: aty128fb: Use backlight helper
Pull x86 fix from Borislav Petkov:
- Prevent the compiler from reordering accesses to debug regs which
could cause a #VC exception in SEV-ES guests at the wrong place in
the NMI handling path
* tag 'x86_urgent_for_v6.2_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Fix stack recursion caused by wrongly ordered DR7 accesses
Pull perf fix from Borislav Petkov:
- Lock the proper critical section when dealing with perf event context
* tag 'perf_urgent_for_v6.2_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_pmu_context serialization
Pull powerpc fixes from Michael Ellerman:
"It's a bit of a big batch for rc6, but just because I didn't send any
fixes the last week or two while I was on vacation, next week should
be quieter:
- Fix a few objtool warnings since we recently enabled objtool.
- Fix a deadlock with the hash MMU vs perf record.
- Fix perf profiling of asynchronous interrupt handlers.
- Revert the IMC PMU nest_init_lock to being a mutex.
- Two commits fixing problems with the kexec_file FDT size
estimation.
- Two commits fixing problems with strict RWX vs kernels running at
non-zero.
- Reconnect tlb_flush() to hash__tlb_flush()
Thanks to Kajol Jain, Nicholas Piggin, Sachin Sant Sathvika Vasireddy,
and Sourabh Jain"
* tag 'powerpc-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Reconnect tlb_flush() to hash__tlb_flush()
powerpc/kexec_file: Count hot-pluggable memory in FDT estimate
powerpc/64s/radix: Fix RWX mapping with relocated kernel
powerpc/64s/radix: Fix crash with unaligned relocated kernel
powerpc/kexec_file: Fix division by zero in extra size estimation
powerpc/imc-pmu: Revert nest_init_lock to being a mutex
powerpc/64: Fix perf profiling asynchronous interrupt handlers
powerpc/64s: Fix local irq disable when PMIs are disabled
powerpc/kvm: Fix unannotated intra-function call warning
powerpc/85xx: Fix unannotated intra-function call warning
Pull RTC fixes from Alexandre Belloni:
"Here are a few fixes for 6.2. The EFI one is the most important as it
allows some RTCs to actually work. The other two are warnings that are
worth fixing.
- efi: make WAKEUP services optional
- sunplus: fix format string warning"
* tag 'rtc-6.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: sunplus: fix format string for printing resource
dt-bindings: rtc: qcom-pm8xxx: allow 'wakeup-source' property
rtc: efi: Enable SET/GET WAKEUP services as optional
Pull Kbuild fixes from Masahiro Yamada:
- Fix two bugs (for building and for signing) when MODULE_SIG_KEY
contains a PKCS#11 URI
* tag 'kbuild-fixes-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: modinst: Fix build error when CONFIG_MODULE_SIG_KEY is a PKCS#11 URI
certs: Fix build error when PKCS#11 URI contains semicolon
Pull kvm fixes from Paolo Bonzini:
"ARM64:
- Yet another fix for non-CPU accesses to the memory backing the
VGICv3 subsystem
- A set of fixes for the setlftest checking for the S1PTW behaviour
after the fix that went in ealier in the cycle"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: aarch64: Test read-only PT memory regions
KVM: selftests: aarch64: Fix check of dirty log PT write
KVM: selftests: aarch64: Do not default to dirty PTE pages on all S1PTWs
KVM: selftests: aarch64: Relax userfaultfd read vs. write checks
KVM: arm64: Allow no running vcpu on saving vgic3 pending table
KVM: arm64: Allow no running vcpu on restoring vgic3 LPI pending status
KVM: arm64: Add helper vgic_write_guest_lock()
Pull parisc architecture fixes from Helge Deller:
- Fix PTRACE_GETREGS/PTRACE_SETREGS for 32-bit userspace on a 64-bit
kernel
- pdc_iodc_print() dropped chars for newline in strings
- Drop constants in favour of PRIV_USER
- use safer strscpy() function in pdc_stable driver
* tag 'parisc-for-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Wire up PTRACE_GETREGS/PTRACE_SETREGS for compat case
parisc: Replace hardcoded value with PRIV_USER constant in ptrace.c
parisc: Fix return code of pdc_iodc_print()
parisc: pdc_stable: use strscpy() to instead of strncpy()
Pull OpenRISC mailing list update from Stafford Horne:
"The old mailing list for OpenRISC died due to some infrastructure
issues and the people in charge decided not to keep it running. We
have migrated this and the users over to kernel.org infrastructure.
Sending this out now to avoid kernel developers getting lots of
bounced mails for using the old list"
* tag 'for-linus' of https://github.com/openrisc/linux:
MAINTAINERS: Update OpenRISC mailing list
KVM/arm64 fixes for 6.2, take #3
- Yet another fix for non-CPU accesses to the memory backing
the VGICv3 subsystem
- A set of fixes for the setlftest checking for the S1PTW
behaviour after the fix that went in ealier in the cycle
Pull block fixes from Jens Axboe:
"A bit bigger than I'd like at this point, but mostly a bunch of little
fixes. In detail:
- NVMe pull request via Christoph:
- Fix a missing queue put in nvmet_fc_ls_create_association
(Amit Engel)
- Clear queue pointers on tag_set initialization failure
(Maurizio Lombardi)
- Use workqueue dedicated to authentication (Shin'ichiro
Kawasaki)
- Fix for an overflow in ublk (Liu)
- Fix for leaking a queue reference in block cgroups (Ming)
- Fix for a use-after-free in BFQ (Yu)"
* tag 'block-6.2-2023-02-03' of git://git.kernel.dk/linux:
blk-cgroup: don't update io stat for root cgroup
nvme-auth: use workqueue dedicated to authentication
nvme: clear the request_queue pointers on failure in nvme_alloc_io_tag_set
nvme: clear the request_queue pointers on failure in nvme_alloc_admin_tag_set
nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
block: Fix the blk_mq_destroy_queue() documentation
block: ublk: extending queue_size to fix overflow
block, bfq: fix uaf for bfqq in bic_set_bfqq()
Pull ceph fix from Ilya Dryomov:
"A safeguard to prevent the kernel client from further damaging the
filesystem after running into a case of an invalid snap trace.
The root cause of this metadata corruption is still being investigated
but it appears to be stemming from the MDS. As such, this is the best
we can do for now"
* tag 'ceph-for-6.2-rc7' of https://github.com/ceph/ceph-client:
ceph: blocklist the kclient when receiving corrupted snap trace
ceph: move mount state enum to super.h
Pull RISC-V fixes from Palmer Dabbelt:
- A build fix to avoid static branches in cpu_relax(), which greatly
inflates the jump tables and breaks at least
CONFIG_CC_OPTIMIZE_FOR_SIZE=y.
- A fix for a kernel panic when probing impossible instruction
positions.
- A fix to disable unwind tables, which are enabled by default for
GCC-13 and result in unhandled relocations in modules.
* tag 'riscv-for-linus-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: disable generation of unwind tables
riscv: kprobe: Fixup kernel panic when probing an illegal position
riscv: Fix build with CONFIG_CC_OPTIMIZE_FOR_SIZE=y
Pull drm fixes from Dave Airlie:
"A few more fixes this week, a bit more spread out though.
We have a bunch of nouveau regression and stabilisation fixes, along
with usual amdgpu, and i915. Otherwise just some minor misc ones:
dma-fence:
- fix signaling bit for private fences
panel:
- boe-tv101wum-nl6 disable fix
nouveau:
- gm20b acr regression fix
- tu102 scrub status fix
- tu102 wait for firmware fix
i915:
- Fixes for potential use-after-free and double-free
- GuC locking and refcount fixes
- Display's reference clock value fix
amdgpu:
- GC11 fixes
- DCN 3.1.4 fixes
- NBIO 4.3 fix
- DCN 3.2 fixes
- Properly handle additional cases where DCN is not supported
- SMU13 fixes
vc4:
- fix CEC adapter names
ssd130x:
- fix display init regression"
* tag 'drm-fixes-2023-02-03' of git://anongit.freedesktop.org/drm/drm: (23 commits)
drm/amd/display: Properly handle additional cases where DCN is not supported
drm/amdgpu: Enable vclk dclk node for gc11.0.3
drm/amd: Fix initialization for nbio 4.3.0
drm/amdgpu: enable HDP SD for gfx 11.0.3
drm/amd/pm: drop unneeded dpm features disablement for SMU 13.0.4/11
drm/amd/display: Reset DMUB mailbox SW state after HW reset
drm/amd/display: Unassign does_plane_fit_in_mall function from dcn3.2
drm/amd/display: Adjust downscaling limits for dcn314
drm/amd/display: Add missing brackets in calculation
drm/amdgpu: update wave data type to 3 for gfx11
drm/panel: boe-tv101wum-nl6: Ensure DSI writes succeed during disable
drm/nouveau/acr/gm20b: regression fixes
drm/nouveau/fb/tu102-: fix register used to determine scrub status
drm/nouveau/devinit/tu102-: wait for GFW_BOOT_PROGRESS == COMPLETED
drm/i915/adlp: Fix typo for reference clock
drm/i915: Fix potential bit_17 double-free
drm/i915: Fix up locking around dumping requests lists
drm/i915: Fix request ref counting during error capture & debugfs dump
drm/i915/guc: Fix locking when searching for a hung request
drm/i915: Avoid potential vm use-after-free
...
Pull misc fixes from Andrew Morton:
"25 hotfixes, mainly for MM. 13 are cc:stable"
* tag 'mm-hotfixes-stable-2023-02-02-19-24-2' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (26 commits)
mm: memcg: fix NULL pointer in mem_cgroup_track_foreign_dirty_slowpath()
Kconfig.debug: fix the help description in SCHED_DEBUG
mm/swapfile: add cond_resched() in get_swap_pages()
mm: use stack_depot_early_init for kmemleak
Squashfs: fix handling and sanity checking of xattr_ids count
sh: define RUNTIME_DISCARD_EXIT
highmem: round down the address passed to kunmap_flush_on_unmap()
migrate: hugetlb: check for hugetlb shared PMD in node migration
mm: hugetlb: proc: check for hugetlb shared PMD in /proc/PID/smaps
mm/MADV_COLLAPSE: catch !none !huge !bad pmd lookups
Revert "mm: kmemleak: alloc gray object for reserved region with direct map"
freevxfs: Kconfig: fix spelling
maple_tree: should get pivots boundary by type
.mailmap: update e-mail address for Eugen Hristev
mm, mremap: fix mremap() expanding for vma's with vm_ops->close()
squashfs: harden sanity check in squashfs_read_xattr_id_table
ia64: fix build error due to switch case label appearing next to declaration
mm: multi-gen LRU: fix crash during cgroup migration
Revert "mm: add nodes= arg to memory.reclaim"
zsmalloc: fix a race with deferred_handles storing
...
When iterating on a linked list, a result of memremap is dereferenced
without checking it for NULL.
This patch adds a check that falls back on allocating a new page in
case memremap doesn't succeed.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 18df7577ad ("efi/memreserve: deal with memreserve entries in unmapped memory")
Signed-off-by: Anton Gusev <aagusev@ispras.ru>
[ardb: return -ENOMEM instead of breaking out of the loop]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Pull libata fix from Damien Le Moal:
"Fix device probe issues with some combination of adapters & devices
that do not report a current link speed, leading to device probe
failures if a link speed was not previously reported and saved (me)"
* tag 'ata-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata: Fix sata_down_spd_limit() when no link speed is reported
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- phy: fix null-deref in phy_attach_direct
- mac802154: fix possible double free upon parsing error
Previous releases - regressions:
- bpf: preserve reg parent/live fields when copying range info,
prevent mis-verification of programs as safe
- ip6: fix GRE tunnels not generating IPv6 link local addresses
- phy: dp83822: fix null-deref on DP83825/DP83826 devices
- sctp: do not check hb_timer.expires when resetting hb_timer
- eth: mtk_sock: fix SGMII configuration after phylink conversion
Previous releases - always broken:
- eth: xdp: execute xdp_do_flush() before napi_complete_done()
- skb: do not mix page pool and page referenced frags in GRO
- bpf:
- fix a possible task gone issue with bpf_send_signal[_thread]()
- fix an off-by-one bug in bpf_mem_cache_idx() to select the right
cache
- add missing btf_put to register_btf_id_dtor_kfuncs
- sockmap: fon't let sock_map_{close,destroy,unhash} call itself
- gso: fix null-deref in skb_segment_list()
- mctp: purge receive queues on sk destruction
- fix UaF caused by accept on already connected socket in exotic
socket families
- tls: don't treat list head as an entry in tls_is_tx_ready()
- netfilter: br_netfilter: disable sabotage_in hook after first
suppression
- wwan: t7xx: fix runtime PM implementation
Misc:
- MAINTAINERS: spring cleanup of networking maintainers"
* tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
mtk_sgmii: enable PCS polling to allow SFP work
net: mediatek: sgmii: fix duplex configuration
net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
MAINTAINERS: update SCTP maintainers
MAINTAINERS: ipv6: retire Hideaki Yoshifuji
mailmap: add John Crispin's entry
MAINTAINERS: bonding: move Veaceslav Falico to CREDITS
net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
virtio-net: Keep stop() to follow mirror sequence of open()
selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
...
Pull KUnit fixes from Shuah Khan:
"Three fixes to bugs that cause kernel crash, link error during build,
and a third to fix kunit_test_init_section_suites() extra indirection
issue"
* tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kunit_test_init_section_suites(...)
kunit: fix bug in KUNIT_EXPECT_MEMEQ
kunit: Export kunit_running()
Pull ARM SoC fixes from Arnd Bergmann:
"The majority of bugfixes is once more for the NXP i.MX platform,
addressing issue with i.MX8M (UART, watchdog and ethernet) as well as
imx8dxl power button and the USB modem on an imx7 board.
The reason that i.MX always shows up here is obviously not that they
are more buggy than the others, but they have the most boards and are
good about getting fixes in quickly.
The other DT fixes are for the Nuvoton wpcm450 flash controller and
the i2c mux on an ASpeed board.
Lastly, there are updates to the MAINTAINERS entries for Mediatek,
AMD/Seattle and NXP SoCs, as well as a lone code fix for error
handling in the allwinner 'rsb' bus driver"
* tag 'soc-fixes-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: wpcm450: Add nuvoton,shm = <&shm> to FIU node
MAINTAINERS: Update entry for MediaTek SoC support
MAINTAINERS: amd: drop inactive Brijesh Singh
ARM: dts: imx7d-smegw01: Fix USB host over-current polarity
arm64: dts: imx8mm-verdin: Do not power down eth-phy
MAINTAINERS: match freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
ARM: dts: aspeed: Fix pca9849 compatible
arm64: dts: freescale: imx8dxl: fix sc_pwrkey's property name linux,keycode
arm64: dts: imx8m-venice: Remove incorrect 'uart-has-rtscts'
arm64: dts: imx8mm: Reinstate GPIO watchdog always-running property on eDM SBC
bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()
Pull s390 fixes from Heiko Carstens:
- With CONFIG_VMAP_STACK enabled it is not possible to load the s390
specific diag288_wdt watchdog module. The reason is that a pointer to
a string is passed to an inline assembly; this string however is
located on the stack, while the instruction within the inline
assembly expects a physicial address. Fix this by copying the string
to a kmalloc'ed buffer.
- The diag288_wdt watchdog module does not indicate that it accesses
memory from an inline assembly, which it does. Add "memory" to the
clobber list to prevent the compiler from optimizing code incorrectly
away.
- Pass size of the uncompressed kernel image to __decompress() call.
Otherwise the kernel image decompressor may corrupt/overwrite an
initrd. This was reported to happen on s390 after commit 2aa14b1ab2
("zstd: import usptream v1.5.2").
* tag 's390-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/decompressor: specify __decompress() buf len to avoid overflow
watchdog: diag288_wdt: fix __diag288() inline assembly
watchdog: diag288_wdt: do not use stack buffers for hardware data
Pull x86 platform driver fixes from Hans de Goede:
"A set of AMD PMF fixes + a few other small fixes"
* tag 'platform-drivers-x86-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: touchscreen_dmi: Add Chuwi Vi8 (CWI501) DMI match
platform/x86: thinkpad_acpi: Fix thinklight LED brightness returning 255
platform/x86/amd: pmc: add CONFIG_SERIO dependency
platform/x86/amd/pmf: Ensure mutexes are initialized before use
platform/x86/amd/pmf: Fix to update SPS thermals when power supply change
platform/x86/amd/pmf: Fix to update SPS default pprof thermals
platform/x86/amd/pmf: update to auto-mode limits only after AMT event
platform/x86/amd/pmf: Add helper routine to check pprof is balanced
platform/x86/amd/pmf: Add helper routine to update SPS thermals
Bjørn Mork says:
====================
Fix mtk_eth_soc sgmii configuration.
This has been tested on a MT7986 with a Maxlinear GPY211C phy
permanently attached to the second SoC mac.
====================
Link: https://lore.kernel.org/r/20230201182331.943411-1-bjorn@mork.no
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently there is no IRQ handling (even the SGMII supports it).
Enable polling to support SFP ports.
Fixes: 14a44ab033 ("net: mtk_eth_soc: partially convert to phylink_pcs")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: changed "1" => "true" ]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The logic of the duplex bit is inverted. Setting it means half
duplex, not full duplex.
Fix and rename macro to avoid confusion.
Fixes: 7e53837269 ("net: ethernet: mediatek: Re-add support SGMII")
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code expect the PHY to be in power down which is only true after reset.
Allow changes of the SGMII parameters more than once.
Only power down when reconfiguring to avoid bouncing the link when there's
no reason to - based on code from Russell King.
There are cases when the SGMII_PHYA_PWD register contains 0x9 which
prevents SGMII from working. The SGMII still shows link but no traffic
can flow. Writing 0x0 to the PHYA_PWD register fix the issue. 0x0 was
taken from a good working state of the SGMII interface.
Fixes: 42c03844e9 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
[ bmork: rebased and squashed into one patch ]
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
can 2023-02-02
The first patch is by Ziyang Xuan and removes a errant WARN_ON_ONCE()
in the CAN J1939 protocol.
The next 3 patches are by Oliver Hartkopp. The first 2 target the CAN
ISO-TP protocol and fix the state machine with respect to signals and
a regression found by the syzbot.
The last patch is by me an missing assignment during the ethtool ring
configuration callback.
* tag 'linux-can-fixes-for-6.2-20230202' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
====================
Link: https://lore.kernel.org/r/20230202094135.2293939-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
MAINTAINERS: spring refresh of networking maintainers
Use Jon Corbet's script for generating statistics about maintainer
coverage to identify inactive maintainers of relatively active code.
Move them to CREDITS.
====================
Link: https://lore.kernel.org/r/20230201182014.2362044-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We very rarely hear from Hideaki Yoshifuji and the IPv4/IPv6
entry covers a lot of code. Asking people to CC someone who
rarely responds feels wrong.
Note that Hideaki Yoshifuji already has an entry in CREDITS
for IPv6 so not adding another one.
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit in fixes tag frees rxq xdp info while RQ NAPI is
still enabled and packet processing may be ongoing.
Follow the mirror sequence of open() in the stop() callback.
This ensures that when rxq info is unregistered, no rx
packet processing is ongoing.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20230202163516.12559-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pul NVMe fixes from Christoph:
"nvme fixes for Linux 6.2
- fix a missing queue put in nvmet_fc_ls_create_association (Amit Engel)
- clear queue pointers on tag_set initialization failure
(Maurizio Lombardi)
- use workqueue dedicated to authentication (Shin'ichiro Kawasaki)"
* tag 'nvme-6.2-2023-02-02' of git://git.infradead.org/nvme:
nvme-auth: use workqueue dedicated to authentication
nvme: clear the request_queue pointers on failure in nvme_alloc_io_tag_set
nvme: clear the request_queue pointers on failure in nvme_alloc_admin_tag_set
nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
UEFI v2.10 introduces version 2 of the memory attributes table, which
turns the reserved field into a flags field, but is compatible with
version 1 in all other respects. So let's not complain about version 2
if we encounter it.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
When received corrupted snap trace we don't know what exactly has
happened in MDS side. And we shouldn't continue IOs and metadatas
access to MDS, which may corrupt or get incorrect contents.
This patch will just block all the further IO/MDS requests
immediately and then evict the kclient itself.
The reason why we still need to evict the kclient just after
blocking all the further IOs is that the MDS could revoke the caps
faster.
Link: https://tracker.ceph.com/issues/57686
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
These flags are only used in ceph filesystem in fs/ceph, so just
move it to the place it should be.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The test tool can check that the zerocopy number of completions value is
valid taking into consideration the number of datagram send calls. This can
catch the system into a state where the datagrams are still in the system
(for example in a qdisk, waiting for the network interface to return a
completion notification, etc).
This change adds a retry logic of computing the number of completions up to
a configurable (via CLI) timeout (default: 2 seconds).
Fixes: 79ebc3c260 ("net/udpgso_bench_tx: options to exercise TX CMSG")
Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230201001612.515730-4-andrei.gherzan@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
"udpgro_bench.sh" invokes udpgso_bench_rx/udpgso_bench_tx programs
subsequently and while doing so, there is a chance that the rx one is not
ready to accept socket connections. This racing bug could fail the test
with at least one of the following:
./udpgso_bench_tx: connect: Connection refused
./udpgso_bench_tx: sendmsg: Connection refused
./udpgso_bench_tx: write: Connection refused
This change addresses this by making udpgro_bench.sh wait for the rx
program to be ready before firing off the tx one - up to a 10s timeout.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230201001612.515730-3-andrei.gherzan@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This change fixes the following compiler warning:
/usr/include/x86_64-linux-gnu/bits/error.h:40:5: warning: ‘gso_size’ may
be used uninitialized [-Wmaybe-uninitialized]
40 | __error_noreturn (__status, __errnum, __format,
__va_arg_pack ());
|
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
udpgso_bench_rx.c: In function ‘main’:
udpgso_bench_rx.c:253:23: note: ‘gso_size’ was declared here
253 | int ret, len, gso_size, budget = 256;
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20230201001612.515730-1-andrei.gherzan@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # >= v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
cpu0 cpu1
j1939_xtp_rx_eoma
j1939_xtp_rx_abort_one
j1939_session_get_by_addr [kref == 2]
j1939_session_get_by_addr [kref == 3]
j1939_session_deactivate [kref == 2]
j1939_session_put [kref == 1]
j1939_session_completed
j1939_session_deactivate
WARN_ON_ONCE(kref < 2)
=====================================================
WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70
CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:j1939_session_deactivate+0x5f/0x70
Call Trace:
j1939_session_deactivate_activate_next+0x11/0x28
j1939_xtp_rx_eoma+0x12a/0x180
j1939_tp_recv+0x4a2/0x510
j1939_can_recv+0x226/0x380
can_rcv_filter+0xf8/0x220
can_receive+0x102/0x220
? process_backlog+0xf0/0x2c0
can_rcv+0x53/0xf0
__netif_receive_skb_one_core+0x67/0x90
? process_backlog+0x97/0x2c0
__netif_receive_skb+0x22/0x80
Fixes: 0c71437dd5 ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object")
Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before the commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
gadget driver.bus was unused. For whatever reason, many UDC drivers set
this field explicitly to NULL in udc_start(). With the newly added gadget
bus, doing this will crash the driver during the attach.
The problem was first reported, fixed and tested with OMAP UDC and g_ether.
Other drivers are changed based on code analysis only.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230201220125.GD2415@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
GCC 13 will enable -fasynchronous-unwind-tables by default on riscv. In
the kernel, we don't have any use for unwind tables yet, so disable them.
More importantly, the .eh_frame section brings relocations
(R_RISC_32_PCREL, R_RISCV_SET{6,8,16}, R_RISCV_SUB{6,8,16}) into modules
that we are not prepared to handle.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmzg9xybqu.fsf@suse.de
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The kernel would panic when probed for an illegal position. eg:
(CONFIG_RISCV_ISA_C=n)
echo 'p:hello kernel_clone+0x16 a0=%a0' >> kprobe_events
echo 1 > events/kprobes/hello/enable
cat trace
Kernel panic - not syncing: stack-protector: Kernel stack
is corrupted in: __do_sys_newfstatat+0xb8/0xb8
CPU: 0 PID: 111 Comm: sh Not tainted
6.2.0-rc1-00027-g2d398fe49a4d #490
Hardware name: riscv-virtio,qemu (DT)
Call Trace:
[<ffffffff80007268>] dump_backtrace+0x38/0x48
[<ffffffff80c5e83c>] show_stack+0x50/0x68
[<ffffffff80c6da28>] dump_stack_lvl+0x60/0x84
[<ffffffff80c6da6c>] dump_stack+0x20/0x30
[<ffffffff80c5ecf4>] panic+0x160/0x374
[<ffffffff80c6db94>] generic_handle_arch_irq+0x0/0xa8
[<ffffffff802deeb0>] sys_newstat+0x0/0x30
[<ffffffff800158c0>] sys_clone+0x20/0x30
[<ffffffff800039e8>] ret_from_syscall+0x0/0x4
---[ end Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: __do_sys_newfstatat+0xb8/0xb8 ]---
That is because the kprobe's ebreak instruction broke the kernel's
original code. The user should guarantee the correction of the probe
position, but it couldn't make the kernel panic.
This patch adds arch_check_kprobe in arch_prepare_kprobe to prevent an
illegal position (Such as the middle of an instruction).
Fixes: c22b0bcb1d ("riscv: Add kprobes supported")
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/r/20230201040604.3390509-1-guoren@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Thomas Winter says:
====================
ip/ip6_gre: Fix GRE tunnels not generating IPv6 link local addresses
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
Also, non-point-to-point tunnels were not generating any IPv6 link
local address and instead generating an IPv6 compat address,
breaking IPv6 communication on the tunnel.
These failures were caused by commit e5dd729460 and this patch set
aims to resolve these issues.
====================
Link: https://lore.kernel.org/r/20230131034646.237671-1-Thomas.Winter@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We recently found that our non-point-to-point tunnels were not
generating any IPv6 link local address and instead generating an
IPv6 compat address, breaking IPv6 communication on the tunnel.
Previously, addrconf_gre_config always would call addrconf_addr_gen
and generate a EUI64 link local address for the tunnel.
Then commit e5dd729460 changed the code path so that add_v4_addrs
is called but this only generates a compat IPv6 address for
non-point-to-point tunnels.
I assume the compat address is specifically for SIT tunnels so
have kept that only for SIT - GRE tunnels now always generate link
local addresses.
Fixes: e5dd729460 ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For our point-to-point GRE tunnels, they have IN6_ADDR_GEN_MODE_NONE
when they are created then we set IN6_ADDR_GEN_MODE_EUI64 when they
come up to generate the IPv6 link local address for the interface.
Recently we found that they were no longer generating IPv6 addresses.
This issue would also have affected SIT tunnels.
Commit e5dd729460 changed the code path so that GRE tunnels
generate an IPv6 address based on the tunnel source address.
It also changed the code path so GRE tunnels don't call addrconf_addr_gen
in addrconf_dev_config which is called by addrconf_sysctl_addr_gen_mode
when the IN6_ADDR_GEN_MODE is changed.
This patch aims to fix this issue by moving the code in addrconf_notify
which calls the addr gen for GRE and SIT into a separate function
and calling it in the places that expect the IPv6 address to be
generated.
The previous addrconf_dev_config is renamed to addrconf_eth_config
since it only expected eth type interfaces and follows the
addrconf_gre/sit_config format.
A part of this changes means that the loopback address will be
attempted to be configured when changing addr_gen_mode for lo.
This should not be a problem because the address should exist anyway
and if does already exist then no error is produced.
Fixes: e5dd729460 ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There could be boards with DCN listed in IP discovery, but no
display hardware actually wired up. In this case the vbios
display table will not be populated. Detect this case and
skip loading DM when we detect it.
v2: Mark DCN as harvested as well so other display checks
elsewhere in the driver are handled properly.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can be out of sync with what's in the hardware, leading
to us rerunning every command that's presently in the ringbuffer.
[How]
Reset software state for the mailboxes in hw_reset callback.
This is already done as part of the mailbox init in hw_init, but we
do need to remember to reset the last cached wptr value as well here.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The hwss function does_plane_fit_in_mall not applicable to dcn3.2 asics.
Using it with dcn3.2 can result in undefined behaviour.
[How]
Assign the function pointer to NULL.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Lower max_downscale_ratio and ARGB888 downscale factor
to prevent cases where underflow may occur on dcn314
[How]
Set max_downscale_ratio to 400 and ARGB downscale factor
to 250 for dcn314
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We source root cgroup stats from the system-wide stats, see blkcg_print_stat
and blkcg_rstat_flush, so don't update io state for root cgroup.
Fixes blkg leak issue introduced in commit 3b8cc62987 ("blk-cgroup: Optimize blkcg_rstat_flush()")
which starts to grab blkg's reference when adding iostat_cpu into percpu
blkcg list, but this state won't be consumed by blkcg_rstat_flush() where
the blkg reference is dropped.
Tested-by: Bart van Assche <bvanassche@acm.org>
Reported-by: Bart van Assche <bvanassche@acm.org>
Fixes: 3b8cc62987 ("blk-cgroup: Optimize blkcg_rstat_flush()")
Cc: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230202021804.278582-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit baf1ed24b2 ("powerpc/mm: Remove empty hash__ functions")
removed some empty hash MMU flushing routines, but got a bit overeager
and also removed the call to hash__tlb_flush() from tlb_flush().
In regular use this doesn't lead to any noticable breakage, which is a
little concerning. Presumably there are flushes happening via other
paths such as arch_leave_lazy_mmu_mode(), and/or a bit of luck.
Fix it by reinstating the call to hash__tlb_flush().
Fixes: baf1ed24b2 ("powerpc/mm: Remove empty hash__ functions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230131111407.806770-1-mpe@ellerman.id.au
Prefer usage of the PRIV_USER constant over the hard-coded value to set
the lowest 2 bits for the userspace privilege.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.16+
Pull virtio fixes from Michael Tsirkin:
"Just small bugfixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa: ifcvf: Do proper cleanup if IFCVF init fails
vhost-scsi: unbreak any layout for response
tools/virtio: fix the vringh test for virtio ring changes
vhost/net: Clear the pending messages when the backend is removed
Pull sound fixes from Takashi Iwai:
"A bit higher volume of changes than wished, but each change is
relatively small and the fix targets are mostly device-specific, so
those should be safe as a late stage merge.
The most significant LoC is about the memalloc helper fix, which is
applied only to Xen PV. The other major parts are ASoC Intel SOF and
AVS fixes that are scattered as various small code changes. The rest
are device-specific fixes and quirks for HD- and USB-audio, FireWire
and ASoC AMD / HDMI"
* tag 'sound-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: firewire-motu: fix unreleased lock warning in hwdep device
ALSA: memalloc: Workaround for Xen PV
ASoC: cs42l56: fix DT probe
ASoC: codecs: wsa883x: correct playback min/max rates
ALSA: hda/realtek: Add Acer Predator PH315-54
ASoC: amd: yc: Add Xiaomi Redmi Book Pro 15 2022 into DMI table
ALSA: hda: Do not unset preset when cleaning up codec
ASoC: SOF: sof-audio: prepare_widgets: Check swidget for NULL on sink failure
ASoC: hdmi-codec: zero clear HDMI pdata
ASoC: SOF: ipc4-mtrace: prevent underflow in sof_ipc4_priority_mask_dfs_write()
ASoC: Intel: sof_ssp_amp: always set dpcm_capture for amplifiers
ASoC: Intel: sof_nau8825: always set dpcm_capture for amplifiers
ASoC: Intel: sof_cs42l42: always set dpcm_capture for amplifiers
ASoC: Intel: sof_rt5682: always set dpcm_capture for amplifiers
ALSA: hda/via: Avoid potential array out-of-bound in add_secret_dac_path()
ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless
ALSA: hda/realtek: fix mute/micmute LEDs, speaker don't work for a HP platform
ASoC: SOF: keep prepare/unprepare widgets in sink path
ASoC: SOF: sof-audio: skip prepare/unprepare if swidget is NULL
ASoC: SOF: sof-audio: unprepare when swidget->use_count > 0
...
NVMe In-Band authentication uses two kinds of works: chap->auth_work and
ctrl->dhchap_auth_work. The latter work flushes or cancels the former
work. However, the both works are queued to the same workqueue nvme-wq.
It results in the lockdep WARNING as follows:
WARNING: possible recursive locking detected
6.2.0-rc4+ #1 Not tainted
--------------------------------------------
kworker/u16:7/69 is trying to acquire lock:
ffff902d52e65548 ((wq_completion)nvme-wq){+.+.}-{0:0}, at: start_flush_work+0x2c5/0x380
but task is already holding lock:
ffff902d52e65548 ((wq_completion)nvme-wq){+.+.}-{0:0}, at: process_one_work+0x210/0x410
To avoid the WARNING, introduce a new workqueue nvme-auth-wq dedicated
to chap->auth_work.
Reported-by: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/linux-nvme/20230130110802.paafkiipmitwtnwr@carbon.lan/
Fixes: f50fff73d6 ("nvme: implement In-Band authentication")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In nvme_alloc_io_tag_set(), the connect_q pointer should be set to NULL
in case of error to avoid potential invalid pointer dereferences.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If nvme_alloc_admin_tag_set() fails, the admin_q and fabrics_q pointers
are left with an invalid, non-NULL value. Other functions may then check
the pointers and dereference them, e.g. in
nvme_probe() -> out_disable: -> nvme_dev_remove_admin().
Fix the bug by setting admin_q and fabrics_q to NULL in case of error.
Also use the set variable to free the tag_set as ctrl->admin_tagset isn't
initialized yet.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As part of nvmet_fc_ls_create_association there is a case where
nvmet_fc_alloc_target_queue fails right after a new association with an
admin queue is created. In this case, no one releases the get taken in
nvmet_fc_alloc_target_assoc. This fix is adding the missing put.
Signed-off-by: Amit Engel <Amit.Engel@dell.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The unprepare sequence has started to fail after moving to panel bridge
code in the msm drm driver (commit 007ac0262b ("drm/msm/dsi: switch to
DRM_PANEL_BRIDGE")). You'll see messages like this in the kernel logs:
panel-boe-tv101wum-nl6 ae94000.dsi.0: failed to set panel off: -22
This is because boe_panel_enter_sleep_mode() needs an operating DSI link
to set the panel into sleep mode. Performing those writes in the
unprepare phase of bridge ops is too late, because the link has already
been torn down by the DSI controller in post_disable, i.e. the PHY has
been disabled, etc. See dsi_mgr_bridge_post_disable() for more details
on the DSI .
Split the unprepare function into a disable part and an unprepare part.
For now, just the DSI writes to enter sleep mode are put in the disable
function. This fixes the panel off routine and keeps the panel happy.
My Wormdingler has an integrated touchscreen that stops responding to
touch if the panel is only half disabled too. This patch fixes it. And
finally, this saves power when the screen is off because without this
fix the regulators for the panel are left enabled when nothing is being
displayed on the screen.
Fixes: 007ac0262b ("drm/msm/dsi: switch to DRM_PANEL_BRIDGE")
Fixes: a869b9db7a ("drm/panel: support for boe tv101wum-nl6 wuxga dsi video mode panel")
Cc: yangcong <yangcong5@huaqin.corp-partner.google.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Jitao Shi <jitao.shi@mediatek.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230106030108.2542081-1-swboyd@chromium.org
(cherry picked from commit c913cd5489)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
commit 8eb060e101 ("arch/riscv: add Zihintpause support") broke
building with CONFIG_CC_OPTIMIZE_FOR_SIZE enabled (gcc 11.1.0):
CC arch/riscv/kernel/vdso/vgettimeofday.o
In file included from <command-line>:
./arch/riscv/include/asm/jump_label.h: In function 'cpu_relax':
././include/linux/compiler_types.h:285:33: warning: 'asm' operand 0 probably does not match constraints
285 | #define asm_volatile_goto(x...) asm goto(x)
| ^~~
./arch/riscv/include/asm/jump_label.h:41:9: note: in expansion of macro 'asm_volatile_goto'
41 | asm_volatile_goto(
| ^~~~~~~~~~~~~~~~~
././include/linux/compiler_types.h:285:33: error: impossible constraint in 'asm'
285 | #define asm_volatile_goto(x...) asm goto(x)
| ^~~
./arch/riscv/include/asm/jump_label.h:41:9: note: in expansion of macro 'asm_volatile_goto'
41 | asm_volatile_goto(
| ^~~~~~~~~~~~~~~~~
make[1]: *** [scripts/Makefile.build:249: arch/riscv/kernel/vdso/vgettimeofday.o] Error 1
make: *** [arch/riscv/Makefile:128: vdso_prepare] Error 2
Having a static branch in cpu_relax() is problematic because that
function is widely inlined, including in some quite complex functions
like in the VDSO. A quick measurement shows this static branch is
responsible by itself for around 40% of the jump table.
Drop the static branch, which ends up being the same number of
instructions anyway. If Zihintpause is supported, we trade the nop from
the static branch for a div. If Zihintpause is unsupported, we trade the
jump from the static branch for (what gets interpreted as) a nop.
Fixes: 8eb060e101 ("arch/riscv: add Zihintpause support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Release bridge info once packet escapes the br_netfilter path,
from Florian Westphal.
2) Revert incorrect fix for the SCTP connection tracking chunk
iterator, also from Florian.
First path fixes a long standing issue, the second path addresses
a mistake in the previous pull request for net.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
Revert "netfilter: conntrack: fix bug in for_each_sctp_chunk"
netfilter: br_netfilter: disable sabotage_in hook after first suppression
====================
Link: https://lore.kernel.org/r/20230131133158.4052-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Meson G12A Internal PHY does not support standard IEEE MMD extended
register access, therefore add generic dummy stubs to fail the read and
write MMD calls. This is necessary to prevent the core PHY code from
erroneously believing that EEE is supported by this PHY even though this
PHY does not support EEE, as MMD register access returns all FFFFs.
Fixes: 5c3407abb3 ("net: phy: meson-gxl: add g12a support")
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230130231402.471493-1-cphealy@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It tries to avoid the frequently hb_timer refresh in commit ba6f5e33bd
("sctp: avoid refreshing heartbeat timer too often"), and it only allows
mod_timer when the new expires is after hb_timer.expires. It means even
a much shorter interval for hb timer gets applied, it will have to wait
until the current hb timer to time out.
In sctp_do_8_2_transport_strike(), when a transport enters PF state, it
expects to update the hb timer to resend a heartbeat every rto after
calling sctp_transport_reset_hb_timer(), which will not work as the
change mentioned above.
The frequently hb_timer refresh was caused by sctp_transport_reset_timers()
called in sctp_outq_flush() and it was already removed in the commit above.
So we don't have to check hb_timer.expires when resetting hb_timer as it is
now not called very often.
Fixes: ba6f5e33bd ("sctp: avoid refreshing heartbeat timer too often")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/d958c06985713ec84049a2d5664879802710179a.1675095933.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On Systems where online memory is lesser compared to max memory, the
kexec_file_load system call may fail to load the kdump kernel with the
below errors:
"Failed to update fdt with linux,drconf-usable-memory property"
"Error setting up usable-memory property for kdump kernel"
This happens because the size estimation for usable memory properties
for the kdump kernel's FDT is based on the online memory whereas the
usable memory properties include max memory. In short, the hot-pluggable
memory is not accounted for while estimating the size of the usable
memory properties.
The issue is addressed by calculating usable memory property size using
max hotplug address instead of the last online memory address.
Fixes: 2377c92e37 ("powerpc/kexec_file: fix FDT size estimation for kdump kernel")
Signed-off-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230131030615.729894-1-sourabhjain@linux.ibm.com
Mirsad report the below error which is caused by stack_depot_init()
failure in kvcalloc. Solve this by having stackdepot use
stack_depot_early_init().
On 1/4/23 17:08, Mirsad Goran Todorovac wrote:
I hate to bring bad news again, but there seems to be a problem with the output of /sys/kernel/debug/kmemleak:
[root@pc-mtodorov ~]# cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff951c118568b0 (size 16):
comm "kworker/u12:2", pid 56, jiffies 4294893952 (age 4356.548s)
hex dump (first 16 bytes):
6d 65 6d 73 74 69 63 6b 30 00 00 00 00 00 00 00 memstick0.......
backtrace:
[root@pc-mtodorov ~]#
Apparently, backtrace of called functions on the stack is no longer
printed with the list of memory leaks. This appeared on Lenovo desktop
10TX000VCR, with AlmaLinux 8.7 and BIOS version M22KT49A (11/10/2022) and
6.2-rc1 and 6.2-rc2 builds. This worked on 6.1 with the same
CONFIG_KMEMLEAK=y and MGLRU enabled on a vanilla mainstream kernel from
Mr. Torvalds' tree. I don't know if this is deliberate feature for some
reason or a bug. Please find attached the config, lshw and kmemleak
output.
[vbabka@suse.cz: remove stack_depot_init() call]
Link: https://lore.kernel.org/all/5272a819-ef74-65ff-be61-4d2d567337de@alu.unizg.hr/
Link: https://lkml.kernel.org/r/1674091345-14799-2-git-send-email-zhaoyang.huang@unisoc.com
Fixes: 56a61617dd ("mm: use stack_depot for recording kmemleak's backtrace")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: ke.wang <ke.wang@unisoc.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
A Sysbot [1] corrupted filesystem exposes two flaws in the handling and
sanity checking of the xattr_ids count in the filesystem. Both of these
flaws cause computation overflow due to incorrect typing.
In the corrupted filesystem the xattr_ids value is 4294967071, which
stored in a signed variable becomes the negative number -225.
Flaw 1 (64-bit systems only):
The signed integer xattr_ids variable causes sign extension.
This causes variable overflow in the SQUASHFS_XATTR_*(A) macros. The
variable is first multiplied by sizeof(struct squashfs_xattr_id) where the
type of the sizeof operator is "unsigned long".
On a 64-bit system this is 64-bits in size, and causes the negative number
to be sign extended and widened to 64-bits and then become unsigned. This
produces the very large number 18446744073709548016 or 2^64 - 3600. This
number when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and
divided by SQUASHFS_METADATA_SIZE overflows and produces a length of 0
(stored in len).
Flaw 2 (32-bit systems only):
On a 32-bit system the integer variable is not widened by the unsigned
long type of the sizeof operator (32-bits), and the signedness of the
variable has no effect due it always being treated as unsigned.
The above corrupted xattr_ids value of 4294967071, when multiplied
overflows and produces the number 4294963696 or 2^32 - 3400. This number
when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and divided by
SQUASHFS_METADATA_SIZE overflows again and produces a length of 0.
The effect of the 0 length computation:
In conjunction with the corrupted xattr_ids field, the filesystem also has
a corrupted xattr_table_start value, where it matches the end of
filesystem value of 850.
This causes the following sanity check code to fail because the
incorrectly computed len of 0 matches the incorrect size of the table
reported by the superblock (0 bytes).
len = SQUASHFS_XATTR_BLOCK_BYTES(*xattr_ids);
indexes = SQUASHFS_XATTR_BLOCKS(*xattr_ids);
/*
* The computed size of the index table (len bytes) should exactly
* match the table start and end points
*/
start = table_start + sizeof(*id_table);
end = msblk->bytes_used;
if (len != (end - start))
return ERR_PTR(-EINVAL);
Changing the xattr_ids variable to be "usigned int" fixes the flaw on a
64-bit system. This relies on the fact the computation is widened by the
unsigned long type of the sizeof operator.
Casting the variable to u64 in the above macro fixes this flaw on a 32-bit
system.
It also means 64-bit systems do not implicitly rely on the type of the
sizeof operator to widen the computation.
[1] https://lore.kernel.org/lkml/000000000000cd44f005f1a0f17f@google.com/
Link: https://lkml.kernel.org/r/20230127061842.10965-1-phillip@squashfs.org.uk
Fixes: 506220d2ba ("squashfs: add more sanity checks in xattr id lookup")
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: <syzbot+082fa4af80a5bb1a9843@syzkaller.appspotmail.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Fedor Pchelkin <pchelkin@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
sh vmlinux fails to link with GNU ld < 2.40 (likely < 2.36) since
commit 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv").
This is similar to fixes for powerpc and s390:
commit 4b9880dbf3 ("powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT").
commit a494398bde ("s390: define RUNTIME_DISCARD_EXIT to fix link error
with GNU ld < 2.36").
$ sh4-linux-gnu-ld --version | head -n1
GNU ld (GNU Binutils for Debian) 2.35.2
$ make ARCH=sh CROSS_COMPILE=sh4-linux-gnu- microdev_defconfig
$ make ARCH=sh CROSS_COMPILE=sh4-linux-gnu-
`.exit.text' referenced in section `__bug_table' of crypto/algboss.o:
defined in discarded section `.exit.text' of crypto/algboss.o
`.exit.text' referenced in section `__bug_table' of
drivers/char/hw_random/core.o: defined in discarded section
`.exit.text' of drivers/char/hw_random/core.o
make[2]: *** [scripts/Makefile.vmlinux:34: vmlinux] Error 1
make[1]: *** [Makefile:1252: vmlinux] Error 2
arch/sh/kernel/vmlinux.lds.S keeps EXIT_TEXT:
/*
* .exit.text is discarded at runtime, not link time, to deal with
* references from __bug_table
*/
.exit.text : AT(ADDR(.exit.text)) { EXIT_TEXT }
However, EXIT_TEXT is thrown away by
DISCARD(include/asm-generic/vmlinux.lds.h) because
sh does not define RUNTIME_DISCARD_EXIT.
GNU ld 2.40 does not have this issue and builds fine.
This corresponds with Masahiro's comments in a494398bde:
"Nathan [Chancellor] also found that binutils
commit 21401fc7bf67 ("Duplicate output sections in scripts") cured this
issue, so we cannot reproduce it with binutils 2.36+, but it is better
to not rely on it."
Link: https://lkml.kernel.org/r/9166a8abdc0f979e50377e61780a4bba1dfa2f52.1674518464.git.tom.saeger@oracle.com
Fixes: 99cb0d917f ("arch: fix broken BuildID for arm64 and riscv")
Link: https://lore.kernel.org/all/Y7Jal56f6UBh1abE@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/all/20230123194218.47ssfzhrpnv3xfez@oracle.com/
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dennis Gilmore <dennis@ausil.us>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Fixes for hugetlb mapcount at most 1 for shared PMDs".
This issue of mapcount in hugetlb pages referenced by shared PMDs was
discussed in [1]. The following two patches address user visible behavior
caused by this issue.
[1] https://lore.kernel.org/linux-mm/Y9BF+OCdWnCSilEu@monkey/
This patch (of 2):
A hugetlb page will have a mapcount of 1 if mapped by multiple processes
via a shared PMD. This is because only the first process increases the
map count, and subsequent processes just add the shared PMD page to their
page table.
page_mapcount is being used to decide if a hugetlb page is shared or
private in /proc/PID/smaps. Pages referenced via a shared PMD were
incorrectly being counted as private.
To fix, check for a shared PMD if mapcount is 1. If a shared PMD is found
count the hugetlb page as shared. A new helper to check for a shared PMD
is added.
[akpm@linux-foundation.org: simplification, per David]
[akpm@linux-foundation.org: hugetlb.h: include page_ref.h for page_count()]
Link: https://lkml.kernel.org/r/20230126222721.222195-2-mike.kravetz@oracle.com
Fixes: 25ee01a2fc ("mm: hugetlb: proc: add hugetlb-related fields to /proc/PID/smaps")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev>
Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In commit 34488399fa ("mm/madvise: add file and shmem support to
MADV_COLLAPSE") we make the following change to find_pmd_or_thp_or_none():
- if (!pmd_present(pmde))
- return SCAN_PMD_NULL;
+ if (pmd_none(pmde))
+ return SCAN_PMD_NONE;
This was for-use by MADV_COLLAPSE file/shmem codepaths, where
MADV_COLLAPSE might identify a pte-mapped hugepage, only to have
khugepaged race-in, free the pte table, and clear the pmd. Such codepaths
include:
A) If we find a suitably-aligned compound page of order HPAGE_PMD_ORDER
already in the pagecache.
B) In retract_page_tables(), if we fail to grab mmap_lock for the target
mm/address.
In these cases, collapse_pte_mapped_thp() really does expect a none (not
just !present) pmd, and we want to suitably identify that case separate
from the case where no pmd is found, or it's a bad-pmd (of course, many
things could happen once we drop mmap_lock, and the pmd could plausibly
undergo multiple transitions due to intervening fault, split, etc).
Regardless, the code is prepared install a huge-pmd only when the existing
pmd entry is either a genuine pte-table-mapping-pmd, or the none-pmd.
However, the commit introduces a logical hole; namely, that we've allowed
!none- && !huge- && !bad-pmds to be classified as genuine
pte-table-mapping-pmds. One such example that could leak through are swap
entries. The pmd values aren't checked again before use in
pte_offset_map_lock(), which is expecting nothing less than a genuine
pte-table-mapping-pmd.
We want to put back the !pmd_present() check (below the pmd_none() check),
but need to be careful to deal with subtleties in pmd transitions and
treatments by various arch.
The issue is that __split_huge_pmd_locked() temporarily clears the present
bit (or otherwise marks the entry as invalid), but pmd_present() and
pmd_trans_huge() still need to return true while the pmd is in this
transitory state. For example, x86's pmd_present() also checks the
_PAGE_PSE , riscv's version also checks the _PAGE_LEAF bit, and arm64 also
checks a PMD_PRESENT_INVALID bit.
Covering all 4 cases for x86 (all checks done on the same pmd value):
1) pmd_present() && pmd_trans_huge()
All we actually know here is that the PSE bit is set. Either:
a) We aren't racing with __split_huge_page(), and PRESENT or PROTNONE
is set.
=> huge-pmd
b) We are currently racing with __split_huge_page(). The danger here
is that we proceed as-if we have a huge-pmd, but really we are
looking at a pte-mapping-pmd. So, what is the risk of this
danger?
The only relevant path is:
madvise_collapse() -> collapse_pte_mapped_thp()
Where we might just incorrectly report back "success", when really
the memory isn't pmd-backed. This is fine, since split could
happen immediately after (actually) successful madvise_collapse().
So, it should be safe to just assume huge-pmd here.
2) pmd_present() && !pmd_trans_huge()
Either:
a) PSE not set and either PRESENT or PROTNONE is.
=> pte-table-mapping pmd (or PROT_NONE)
b) devmap. This routine can be called immediately after
unlocking/locking mmap_lock -- or called with no locks held (see
khugepaged_scan_mm_slot()), so previous VMA checks have since been
invalidated.
3) !pmd_present() && pmd_trans_huge()
Not possible.
4) !pmd_present() && !pmd_trans_huge()
Neither PRESENT nor PROTNONE set
=> not present
I've checked all archs that implement pmd_trans_huge() (arm64, riscv,
powerpc, longarch, x86, mips, s390) and this logic roughly translates
(though devmap treatment is unique to x86 and powerpc, and (3) doesn't
necessarily hold in general -- but that doesn't matter since
!pmd_present() always takes failure path).
Also, add a comment above find_pmd_or_thp_or_none() to help future
travelers reason about the validity of the code; namely, the possible
mutations that might happen out from under us, depending on how mmap_lock
is held (if at all).
Link: https://lkml.kernel.org/r/20230125225358.2576151-1-zokeefe@google.com
Fixes: 34488399fa ("mm/madvise: add file and shmem support to MADV_COLLAPSE")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Reported-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fabian has reported another regression in 6.1 due to ca3d76b0aa ("mm:
add merging after mremap resize"). The problem is that vma_merge() can
fail when vma has a vm_ops->close() method, causing is_mergeable_vma()
test to be negative. This was happening for vma mapping a file from
fuse-overlayfs, which does have the method. But when we are simply
expanding the vma, we never remove it due to the "merge" with the added
area, so the test should not prevent the expansion.
As a quick fix, check for such vmas and expand them using vma_adjust()
directly as was done before commit ca3d76b0aa. For a more robust long
term solution we should try to limit the check for vma_ops->close only to
cases that actually result in vma removal, so that no merge would be
prevented unnecessarily.
[akpm@linux-foundation.org: fix indenting whitespace, reflow comment]
Link: https://lkml.kernel.org/r/20230117101939.9753-1-vbabka@suse.cz
Fixes: ca3d76b0aa ("mm: add merging after mremap resize")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Fabian Vogt <fvogt@suse.com>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1206359#c35
Tested-by: Fabian Vogt <fvogt@suse.com>
Cc: Jakub Matěna <matenajakub@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since commit aa06a9bd85 ("ia64: fix clock_getres(CLOCK_MONOTONIC) to
report ITC frequency"), gcc 10.1.0 fails to build ia64 with the gnomic:
| ../arch/ia64/kernel/sys_ia64.c: In function 'ia64_clock_getres':
| ../arch/ia64/kernel/sys_ia64.c:189:3: error: a label can only be part of a statement and a declaration is not a statement
| 189 | s64 tick_ns = DIV_ROUND_UP(NSEC_PER_SEC, local_cpu_data->itc_freq);
This line appears immediately after a case label in a switch.
Move the declarations out of the case, to the top of the function.
Link: https://lkml.kernel.org/r/20230117151632.393836-1-james.morse@arm.com
Fixes: aa06a9bd85 ("ia64: fix clock_getres(CLOCK_MONOTONIC) to report ITC frequency")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Sergei Trofimovich <slyich@gmail.com>
Cc: Émeric Maschino <emeric.maschino@gmail.com>
Cc: matoro <matoro_mailinglist_kernel@matoro.tk>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently, there is a race between zs_free() and zs_reclaim_page():
zs_reclaim_page() finds a handle to an allocated object, but before the
eviction happens, an independent zs_free() call to the same handle could
come in and overwrite the object value stored at the handle with the last
deferred handle. When zs_reclaim_page() finally gets to call the eviction
handler, it will see an invalid object value (i.e the previous deferred
handle instead of the original object value).
This race happens quite infrequently. We only managed to produce it with
out-of-tree developmental code that triggers zsmalloc writeback with a
much higher frequency than usual.
This patch fixes this race by storing the deferred handle in the object
header instead. We differentiate the deferred handle from the other two
cases (handle for allocated object, and linkage for free object) with a
new tag. If zspage reclamation succeeds, we will free these deferred
handles by walking through the zspage objects. On the other hand, if
zspage reclamation fails, we reconstruct the zspage freelist (with the
deferred handle tag and allocated tag) before trying again with the
reclamation.
[arnd@arndb.de: avoid unused-function warning]
Link: https://lkml.kernel.org/r/20230117170507.2651972-1-arnd@kernel.org
Link: https://lkml.kernel.org/r/20230110231701.326724-1-nphamcs@gmail.com
Fixes: 9997bc0175 ("zsmalloc: implement writeback mechanism for zsmalloc")
Signed-off-by: Nhat Pham <nphamcs@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If an ->anon_vma is attached to the VMA, collapse_and_free_pmd() requires
it to be locked.
Page table traversal is allowed under any one of the mmap lock, the
anon_vma lock (if the VMA is associated with an anon_vma), and the
mapping lock (if the VMA is associated with a mapping); and so to be
able to remove page tables, we must hold all three of them.
retract_page_tables() bails out if an ->anon_vma is attached, but does
this check before holding the mmap lock (as the comment above the check
explains).
If we racily merged an existing ->anon_vma (shared with a child
process) from a neighboring VMA, subsequent rmap traversals on pages
belonging to the child will be able to see the page tables that we are
concurrently removing while assuming that nothing else can access them.
Repeat the ->anon_vma check once we hold the mmap lock to ensure that
there really is no concurrent page table access.
Hitting this bug causes a lockdep warning in collapse_and_free_pmd(),
in the line "lockdep_assert_held_write(&vma->anon_vma->root->rwsem)".
It can also lead to use-after-free access.
Link: https://lore.kernel.org/linux-mm/CAG48ez3434wZBKFFbdx4M9j6eUwSUVPd4dxhzW_k_POneSDF+A@mail.gmail.com/
Link: https://lkml.kernel.org/r/20230111133351.807024-1-jannh@google.com
Fixes: f3f0e1d215 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Jann Horn <jannh@google.com>
Reported-by: Zach O'Keefe <zokeefe@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@intel.linux.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Pull cgroup fix from Tejun Heo:
"cpuset has a bug which can cause an oops after some configuration
operations, introduced during the v6.1 cycle.
This single commit fixes the bug"
* tag 'cgroup-for-6.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Fix wrong check in update_parent_subparts_cpumask()
It was found that the check to see if a partition could use up all
the cpus from the parent cpuset in update_parent_subparts_cpumask()
was incorrect. As a result, it is possible to leave parent with no
effective cpu left even if there are tasks in the parent cpuset. This
can lead to system panic as reported in [1].
Fix this probem by updating the check to fail the enabling the partition
if parent's effective_cpus is a subset of the child's cpus_allowed.
Also record the error code when an error happens in update_prstate()
and add a test case where parent partition and child have the same cpu
list and parent has task. Enabling partition in the child will fail in
this case.
[1] https://www.spinics.net/lists/cgroups/msg36254.html
Fixes: f0af1bfc27 ("cgroup/cpuset: Relax constraints to partition & cpus changes")
Cc: stable@vger.kernel.org # v6.1
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull SCSI fixes from James Bottomley:
"Two core fixes.
One simply moves an annotation from put to release to avoid the
warning triggering needlessly in alua, but to keep it in case release
is ever called from that path (which we don't think will happen).
The other reverts a change to the PQ=1 target scanning behaviour
that's under intense discussion at the moment"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Revert "scsi: core: map PQ=1, PDT=other values to SCSI_SCAN_TARGET_PRESENT"
scsi: core: Fix the scsi_device_put() might_sleep annotation
Syzkaller triggered a WARN in put_pmu_ctx().
WARNING: CPU: 1 PID: 2245 at kernel/events/core.c:4925 put_pmu_ctx+0x1f0/0x278
This is because there is no locking around the access of "if
(!epc->ctx)" in find_get_pmu_context() and when it is set to NULL in
put_pmu_ctx().
The decrement of the reference count in put_pmu_ctx() also happens
outside of the spinlock, leading to the possibility of this order of
events, and the context being cleared in put_pmu_ctx(), after its
refcount is non zero:
CPU0 CPU1
find_get_pmu_context()
if (!epc->ctx) == false
put_pmu_ctx()
atomic_dec_and_test(&epc->refcount) == true
epc->refcount == 0
atomic_inc(&epc->refcount);
epc->refcount == 1
list_del_init(&epc->pmu_ctx_entry);
epc->ctx = NULL;
Another issue is that WARN_ON for no active PMU events in put_pmu_ctx()
is outside of the lock. If the perf_event_pmu_context is an embedded
one, even after clearing it, it won't be deleted and can be re-used. So
the warning can trigger. For this reason it also needs to be moved
inside the lock.
The above warning is very quick to trigger on Arm by running these two
commands at the same time:
while true; do perf record -- ls; done
while true; do perf record -- ls; done
[peterz: atomic_dec_and_raw_lock*()]
Fixes: bd27568117 ("perf: Rewrite core context handling")
Reported-by: syzbot+697196bc0265049822bd@syzkaller.appspotmail.com
Signed-off-by: James Clark <james.clark@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20230127143141.1782804-2-james.clark@arm.com
Pull media fixes from Mauro Carvalho Chehab:
"A couple of v4l2 core fixes:
- fix a regression on strings control support
- fix a regression for some drivers that depend on an odd streaming
behavior"
* tag 'media/v6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videobuf2: set q->streaming later
media: v4l2-ctrls-api.c: move ctrl->is_new = 1 to the correct line
Historically calls to __decompress() didn't specify "out_len" parameter
on many architectures including s390, expecting that no writes beyond
uncompressed kernel image are performed. This has changed since commit
2aa14b1ab2 ("zstd: import usptream v1.5.2") which includes zstd library
commit 6a7ede3dfccb ("Reduce size of dctx by reutilizing dst buffer
(#2751)"). Now zstd decompression code might store literal buffer in
the unwritten portion of the destination buffer. Since "out_len" is
not set, it is considered to be unlimited and hence free to use for
optimization needs. On s390 this might corrupt initrd or ipl report
which are often placed right after the decompressor buffer. Luckily the
size of uncompressed kernel image is already known to the decompressor,
so to avoid the problem simply specify it in the "out_len" parameter.
Link: https://github.com/facebook/zstd/commit/6a7ede3dfccb
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/patch-1.thread-41c676.git-41c676c2d153.your-ad-here.call-01675030179-ext-9637@work.hours
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Looks like kunit_test_init_section_suites(...) was messed up in a merge
conflict. This fixes it.
kunit_test_init_section_suites(...) was not updated to avoid the extra
level of indirection when .kunit_test_suites was flattened. Given no-one
was actively using it, this went unnoticed for a long period of time.
Fixes: e5857d396f ("kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites")
Signed-off-by: Brendan Higgins <brendan.higgins@linux.dev>
Signed-off-by: David Gow <davidgow@google.com>
Tested-by: Martin Fernandez <martin.fernandez@eclypsium.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The mailing list at librecores.org is being shut down due to
infrastructure issues. Update the the newly created list on
vger.kernel.org.
Signed-off-by: Stafford Horne <shorne@gmail.com>
When validating drafted SPDK ublk target, in a case that
assigning large queue depth to multiqueue ublk device,
ublk target would run into a weird incorrect state. During
rounds of review and debug, An overflow bug was found
in ublk driver.
In ublk_cmd.h, UBLK_MAX_QUEUE_DEPTH is 4096 which means
each ublk queue depth can be set as large as 4096. But
when setting qd for a ublk device,
sizeof(struct ublk_queue) + depth * sizeof(struct ublk_io)
will be larger than 65535 if qd is larger than 2728.
Then queue_size is overflowed, and ublk_get_queue()
references a wrong pointer position. The wrong content of
ublk_queue elements will lead to out-of-bounds memory
access.
Extend queue_size in ublk_device as "unsigned int".
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230131070552.115067-1-xiaodong.liu@intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no bug. If sch->length == 0, this would result in an infinite
loop, but first caller, do_basic_checks(), errors out in this case.
After this change, packets with bogus zero-length chunks are no longer
detected as invalid, so revert & add comment wrt. 0 length check.
Fixes: 98ee007745 ("netfilter: conntrack: fix bug in for_each_sctp_chunk")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When using a xfrm interface in a bridged setup (the outgoing device is
bridged), the incoming packets in the xfrm interface are only tracked
in the outgoing direction.
$ brctl show
bridge name interfaces
br_eth1 eth1
$ conntrack -L
tcp 115 SYN_SENT src=192... dst=192... [UNREPLIED] ...
If br_netfilter is enabled, the first (encrypted) packet is received onR
eth1, conntrack hooks are called from br_netfilter emulation which
allocates nf_bridge info for this skb.
If the packet is for local machine, skb gets passed up the ip stack.
The skb passes through ip prerouting a second time. br_netfilter
ip_sabotage_in supresses the re-invocation of the hooks.
After this, skb gets decrypted in xfrm layer and appears in
network stack a second time (after decryption).
Then, ip_sabotage_in is called again and suppresses netfilter
hook invocation, even though the bridge layer never called them
for the plaintext incarnation of the packet.
Free the bridge info after the first suppression to avoid this.
I was unable to figure out where the regression comes from, as far as i
can see br_netfilter always had this problem; i did not expect that skb
is looped again with different headers.
Fixes: c4b0e771f9 ("netfilter: avoid using skb->nf_bridge directly")
Reported-and-tested-by: Wolfgang Nothdurft <wolfgang@linogate.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In kernels compiled with CONFIG_PARAVIRT=n, the compiler re-orders the
DR7 read in exc_nmi() to happen before the call to sev_es_ist_enter().
This is problematic when running as an SEV-ES guest because in this
environment the DR7 read might cause a #VC exception, and taking #VC
exceptions is not safe in exc_nmi() before sev_es_ist_enter() has run.
The result is stack recursion if the NMI was caused on the #VC IST
stack, because a subsequent #VC exception in the NMI handler will
overwrite the stack frame of the interrupted #VC handler.
As there are no compiler barriers affecting the ordering of DR7
reads/writes, make the accesses to this register volatile, forbidding
the compiler to re-order them.
[ bp: Massage text, make them volatile too, to make sure some
aggressive compiler optimization pass doesn't discard them. ]
Fixes: 315562c9af ("x86/sev-es: Adjust #VC IST Stack on entering NMI handler")
Reported-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230127035616.508966-1-aik@amd.com
If a relocatable kernel is loaded at a non-zero address and told not to
relocate to zero (kdump or RELOCATABLE_TEST), the mapping of the
interrupt code at zero is left with RWX permissions.
That is a security weakness, and leads to a warning at boot if
CONFIG_DEBUG_WX is enabled:
powerpc/mm: Found insecure W+X mapping at address 00000000056435bc/0xc000000000000000
WARNING: CPU: 1 PID: 1 at arch/powerpc/mm/ptdump/ptdump.c:193 note_page+0x484/0x4c0
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.2.0-rc1-00001-g8ae8e98aea82-dirty #175
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,git-dd0dca hv:linux,kvm pSeries
NIP: c0000000004a1c34 LR: c0000000004a1c30 CTR: 0000000000000000
REGS: c000000003503770 TRAP: 0700 Not tainted (6.2.0-rc1-00001-g8ae8e98aea82-dirty)
MSR: 8000000002029033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 24000220 XER: 00000000
CFAR: c000000000545a58 IRQMASK: 0
...
NIP note_page+0x484/0x4c0
LR note_page+0x480/0x4c0
Call Trace:
note_page+0x480/0x4c0 (unreliable)
ptdump_pmd_entry+0xc8/0x100
walk_pgd_range+0x618/0xab0
walk_page_range_novma+0x74/0xc0
ptdump_walk_pgd+0x98/0x170
ptdump_check_wx+0x94/0x100
mark_rodata_ro+0x30/0x70
kernel_init+0x78/0x1a0
ret_from_kernel_thread+0x5c/0x64
The fix has two parts. Firstly the pages from zero up to the end of
interrupts need to be marked read-only, so that they are left with R-X
permissions. Secondly the mapping logic needs to be taught to ensure
there is a page boundary at the end of the interrupt region, so that the
permission change only applies to the interrupt text, and not the region
following it.
Fixes: c55d7b5e64 ("powerpc: Remove STRICT_KERNEL_RWX incompatibility with RELOCATABLE")
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230110124753.1325426-2-mpe@ellerman.id.au
If a relocatable kernel is loaded at an address that is not 2MB aligned
and told not to relocate to zero, the kernel can crash due to
mark_rodata_ro() incorrectly changing some read-write data to read-only.
Scenarios where the misalignment can occur are when the kernel is
loaded by kdump or using the RELOCATABLE_TEST config option.
Example crash with the kernel loaded at 5MB:
Run /sbin/init as init process
BUG: Unable to handle kernel data access on write at 0xc000000000452000
Faulting instruction address: 0xc0000000005b6730
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
CPU: 1 PID: 1 Comm: init Not tainted 6.2.0-rc1-00011-g349188be4841 #166
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,git-5b4c5a hv:linux,kvm pSeries
NIP: c0000000005b6730 LR: c000000000ae9ab8 CTR: 0000000000000380
REGS: c000000004503250 TRAP: 0300 Not tainted (6.2.0-rc1-00011-g349188be4841)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 44288480 XER: 00000000
CFAR: c0000000005b66ec DAR: c000000000452000 DSISR: 0a000000 IRQMASK: 0
...
NIP memset+0x68/0x104
LR zero_user_segments.constprop.0+0xa8/0xf0
Call Trace:
ext4_mpage_readpages+0x7f8/0x830
ext4_readahead+0x48/0x60
read_pages+0xb8/0x380
page_cache_ra_unbounded+0x19c/0x250
filemap_fault+0x58c/0xae0
__do_fault+0x60/0x100
__handle_mm_fault+0x1230/0x1a40
handle_mm_fault+0x120/0x300
___do_page_fault+0x20c/0xa80
do_page_fault+0x30/0xc0
data_access_common_virt+0x210/0x220
This happens because mark_rodata_ro() tries to change permissions on the
range _stext..__end_rodata, but _stext sits in the middle of the 2MB
page from 4MB to 6MB:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000002400000 with 2.00 MiB pages (exec)
The logic that changes the permissions assumes the linear mapping was
split correctly at boot, so it marks the entire 2MB page read-only. That
leads to the write fault above.
To fix it, the boot time mapping logic needs to consider that if the
kernel is running at a non-zero address then _stext is a boundary where
it must split the mapping.
That leads to the mapping being split correctly, allowing the rodata
permission change to take happen correctly, with no spillover:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000000500000 with 64.0 KiB pages
radix-mmu: Mapped 0x0000000000500000-0x0000000000600000 with 64.0 KiB pages (exec)
radix-mmu: Mapped 0x0000000000600000-0x0000000002400000 with 2.00 MiB pages (exec)
If the kernel is loaded at a 2MB aligned address, the mapping continues
to use 2MB pages as before:
radix-mmu: Mapped 0x0000000000000000-0x0000000000200000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000000200000-0x0000000000400000 with 2.00 MiB pages
radix-mmu: Mapped 0x0000000000400000-0x0000000002c00000 with 2.00 MiB pages (exec)
radix-mmu: Mapped 0x0000000002c00000-0x0000000100000000 with 2.00 MiB pages
Fixes: c55d7b5e64 ("powerpc: Remove STRICT_KERNEL_RWX incompatibility with RELOCATABLE")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230110124753.1325426-1-mpe@ellerman.id.au
In kexec_extra_fdt_size_ppc64() there's logic to estimate how much
extra space will be needed in the device tree for some memory related
properties.
That logic uses the size of RAM divided by drmem_lmb_size() to do the
estimation. However drmem_lmb_size() can be zero if the machine has no
hotpluggable memory configured, which is the case when booting with qemu
and no maxmem=x parameter is passed (the default).
The division by zero is reported by UBSAN, and can also lead to an
overflow and a warning from kvmalloc, and kdump kernel loading fails:
WARNING: CPU: 0 PID: 133 at mm/util.c:596 kvmalloc_node+0x15c/0x160
Modules linked in:
CPU: 0 PID: 133 Comm: kexec Not tainted 6.2.0-rc5-03455-g07358bd97810 #223
Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1200 0xf000005 of:SLOF,git-dd0dca pSeries
NIP: c00000000041ff4c LR: c00000000041fe58 CTR: 0000000000000000
REGS: c0000000096ef750 TRAP: 0700 Not tainted (6.2.0-rc5-03455-g07358bd97810)
MSR: 800000000282b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 24248242 XER: 2004011e
CFAR: c00000000041fed0 IRQMASK: 0
...
NIP kvmalloc_node+0x15c/0x160
LR kvmalloc_node+0x68/0x160
Call Trace:
kvmalloc_node+0x68/0x160 (unreliable)
of_kexec_alloc_and_setup_fdt+0xb8/0x7d0
elf64_load+0x25c/0x4a0
kexec_image_load_default+0x58/0x80
sys_kexec_file_load+0x5c0/0x920
system_call_exception+0x128/0x330
system_call_vectored_common+0x15c/0x2ec
To fix it, skip the calculation if drmem_lmb_size() is zero.
Fixes: 2377c92e37 ("powerpc/kexec_file: fix FDT size estimation for kdump kernel")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230130014707.541110-1-mpe@ellerman.id.au
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
"1st set of IIO fixes for the 6.2 cycle.
The usual mixed bag - with a bunch of issues found by Carlos Song
in the fxos8700 IMU driver dominating.
hid-accel,gyro
- Fix wrong returned value when read succeeds.
marvell,berlin-adc
- Missing of_node_put() in an error path.
nxp,fxos8700 (freescale)
- Wrong channel type match.
- Swapped channel read back.
- Incomplete channel read back (not enough bytes).
- Missing shift of acceleration data.
- Range selection didn't work (datasheet bug)
- Wrong ODR mode read back due to wrong field offset.
- Drop unused, but wrong define.
- Fix issue with magnetometer scale an units.
nxp,imx8qxp
- Fix an irq flood due to not reading data early enough.
st,lsm6dsx
- Add CONFIG_IIO_TRIGGERED_BUFFER select.
st,stm32-adc
- Fix missing MODULE_DEVICE_TABLE() needed for module aliases.
ti,twl6030
- Fix missing enable of some channels.
- Fix a typo in previous patch that meant one channel still wasn't enabled.
xilinx,xadc
- Carrying on incorrectly after allocation error."
* tag 'iio-fixes-for-6.2a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: imu: fxos8700: fix MAGN sensor scale and unit
iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
iio: imu: fxos8700: fix failed initialization ODR mode assignment
iio: imu: fxos8700: fix incorrect ODR mode readback
iio: light: cm32181: Fix PM support on system with 2 I2C resources
iio: hid: fix the retval in gyro_3d_capture_sample
iio: hid: fix the retval in accel_3d_capture_sample
iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
iio:adc:twl6030: Enable measurement of VAC
iio: imu: fxos8700: fix ACCEL measurement range selection
iio: imu: fxos8700: fix IMU data bits returned to user space
iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
iio: imu: fxos8700: fix map label of channel type to MAGN sensor
iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
iio: imx8qxp-adc: fix irq flood when call imx8qxp_adc_read_raw()
iio: adc: xilinx-ams: fix devm_krealloc() return value check
iio: adc: berlin2-adc: Add missing of_node_put() in error path
iio: adc: stm32-dfsdm: fill module aliases
When CONFIG_MODULE_SIG_KEY is PKCS#11 URI (pkcs11:*), signing of modules
fails:
scripts/sign-file sha256 /.../linux/pkcs11:token=foo;object=bar;pin-value=1111 certs/signing_key.x509 /.../kernel/crypto/tcrypt.ko
Usage: scripts/sign-file [-dp] <hash algo> <key> <x509> <module> [<dest>]
scripts/sign-file -s <raw sig> <hash algo> <x509> <module> [<dest>]
First, we need to avoid adding the $(srctree)/ prefix to the URL.
Second, since the kconfig string values no longer include quotes, we need to add
them again when passing a PKCS#11 URI to sign-file. This avoids
splitting by the shell if the URI contains semicolons.
Fixes: 4db9c2e3d0 ("kbuild: stop using config_filename in scripts/Makefile.modsign")
Fixes: 129ab0d2d9 ("kbuild: do not quote string values in include/config/auto.conf")
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When CONFIG_MODULE_SIG_KEY is PKCS#11 URI (pkcs11:*) and contains a
semicolon, signing_key.x509 fails to build:
certs/extract-cert pkcs11:token=foo;object=bar;pin-value=1111 certs/signing_key.x509
Usage: extract-cert <source> <dest>
Add quotes to the extract-cert argument to avoid splitting by the shell.
This approach was suggested by Masahiro Yamada <masahiroy@kernel.org>.
Fixes: 129ab0d2d9 ("kbuild: do not quote string values in include/config/auto.conf")
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Stefan Schmidt says:
====================
ieee802154 for net 2023-01-30
Only one fix this time around.
Miquel Raynal fixed a potential double free spotted by Dan Carpenter.
* tag 'ieee802154-for-net-2023-01-30' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
mac802154: Fix possible double free upon parsing error
====================
Link: https://lore.kernel.org/r/20230130095646.301448-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-01-27 (ice)
This series contains updates to ice driver only.
Dave prevents modifying channels when RDMA is active as this will break
RDMA traffic.
Michal fixes a broken URL.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix broken link in ice NAPI doc
ice: Prevent set_channel from changing queues while RDMA active
====================
Link: https://lore.kernel.org/r/20230127225333.1534783-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The recent commit 76d588dddc ("powerpc/imc-pmu: Fix use of mutex in
IRQs disabled section") fixed warnings (and possible deadlocks) in the
IMC PMU driver by converting the locking to use spinlocks.
It also converted the init-time nest_init_lock to a spinlock, even
though it's not used at runtime in IRQ disabled sections or while
holding other spinlocks.
This leads to warnings such as:
BUG: sleeping function called from invalid context at include/linux/percpu-rwsem.h:49
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 6.2.0-rc2-14719-gf12cd06109f4-dirty #1
Hardware name: Mambo,Simulated-System POWER9 0x4e1203 opal:v6.6.6 PowerNV
Call Trace:
dump_stack_lvl+0x74/0xa8 (unreliable)
__might_resched+0x178/0x1a0
__cpuhp_setup_state+0x64/0x1e0
init_imc_pmu+0xe48/0x1250
opal_imc_counters_probe+0x30c/0x6a0
platform_probe+0x78/0x110
really_probe+0x104/0x420
__driver_probe_device+0xb0/0x170
driver_probe_device+0x58/0x180
__driver_attach+0xd8/0x250
bus_for_each_dev+0xb4/0x140
driver_attach+0x34/0x50
bus_add_driver+0x1e8/0x2d0
driver_register+0xb4/0x1c0
__platform_driver_register+0x38/0x50
opal_imc_driver_init+0x2c/0x40
do_one_initcall+0x80/0x360
kernel_init_freeable+0x310/0x3b8
kernel_init+0x30/0x1a0
ret_from_kernel_thread+0x5c/0x64
Fix it by converting nest_init_lock back to a mutex, so that we can call
sleeping functions while holding it. There is no interaction between
nest_init_lock and the runtime spinlocks used by the actual PMU routines.
Fixes: 76d588dddc ("powerpc/imc-pmu: Fix use of mutex in IRQs disabled section")
Tested-by: Kajol Jain<kjain@linux.ibm.com>
Reviewed-by: Kajol Jain<kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230130014401.540543-1-mpe@ellerman.id.au
Starting from Turing, the driver is no longer responsible for initiating
DEVINIT when required as the GPU started loading a FW image from ROM and
executing DEVINIT itself after power-on.
However - we apparently still need to wait for it to complete.
This should correct some issues with runpm on some systems, where we get
control of the HW before it's been fully reinitialised after resume from
suspend.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130223715.1831509-1-bskeggs@redhat.com
In KUNIT_EXPECT_MEMEQ and KUNIT_EXPECT_MEMNEQ, add check if one of the
inputs is NULL and fail if this is the case.
Currently, the kernel crashes if one of the inputs is NULL. Instead,
fail the test and add an appropriate error message.
Fixes: b8a926bea8 ("kunit: Introduce KUNIT_EXPECT_MEMEQ and KUNIT_EXPECT_MEMNEQ macros")
This was found by the kernel test robot:
https://lore.kernel.org/all/202212191448.D6EDPdOh-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rae Moar <rmoar@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When GuC support was added to error capture, the reference counting
around the request object was broken. Fix it up.
The context based search manages the spinlocking around the search
internally. So it needs to grab the reference count internally as
well. The execlist only request based search relies on external
locking, so it needs an external reference count but within the
spinlock not outside it.
The only other caller of the context based search is the code for
dumping engine state to debugfs. That code wasn't previously getting
an explicit reference at all as it does everything while holding the
execlist specific spinlock. So, that needs updaing as well as that
spinlock doesn't help when using GuC submission. Rather than trying to
conditionally get/put depending on submission model, just change it to
always do the get/put.
v2: Explicitly document adding an extra blank line in some dense code
(Andy Shevchenko). Fix multiple potential null pointer derefs in case
of no request found (some spotted by Tvrtko, but there was more!).
Also fix a leaked request in case of !started and another in
__guc_reset_context now that intel_context_find_active_request is
actually reference counting the returned request.
v3: Add a _get suffix to intel_context_find_active_request now that it
grabs a reference (Daniele).
v4: Split the intel_guc_find_hung_context change to a separate patch
and rename intel_context_find_active_request_get to
intel_context_get_active_request (Tvrtko).
v5: s/locking/reference counting/ in commit message (Tvrtko)
Fixes: dc0dad365c ("drm/i915/guc: Fix for error capture after full GPU reset with GuC")
Fixes: 573ba126ae ("drm/i915/guc: Capture error state on context reset")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Michael Cheng <michael.cheng@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aravind Iddamsetty <aravind.iddamsetty@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127002842.3169194-3-John.C.Harrison@Intel.com
(cherry picked from commit 3700e35378)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull fscache fixes from David Howells:
"Fix two problems in fscache volume handling:
- wake_up_bit() is incorrectly paired with wait_var_event(). The
latter selects the waitqueue to use differently.
- Missing barriers ordering between state bit and task state"
* tag 'fscache-fixes-20230130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
fscache: Use clear_and_wake_up_bit() in fscache_create_volume_work()
fscache: Use wait_on_bit() to wait for the freeing of relinquished volume
i.MX fixes for 6.2, round 2:
- Update MAINTAINERS i.MX entry to match arm64 freescale DTS.
- Drop misused 'uart-has-rtscts' from imx8m-venice boards.
- Fix USB host over-current polarity for imx7d-smegw01 board.
- Fix a typo in i.MX8DXL sc_pwrkey property name.
- Fix GPIO watchdog property for i.MX8MM eDM SBC board.
- Keep Ethernet PHY powered on imx8mm-verdin to avoid kernel crash.
- Fix configuration of i.MX8MM pad UART1_DTE_RX.
* tag 'imx-fixes-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-smegw01: Fix USB host over-current polarity
arm64: dts: imx8mm-verdin: Do not power down eth-phy
MAINTAINERS: match freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
arm64: dts: freescale: imx8dxl: fix sc_pwrkey's property name linux,keycode
arm64: dts: imx8m-venice: Remove incorrect 'uart-has-rtscts'
arm64: dts: imx8mm: Reinstate GPIO watchdog always-running property on eDM SBC
Link: https://lore.kernel.org/r/20230130003614.GP20713@T480
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DIAG 288 statement consumes an EBCDIC string the address of which is
passed in a register. Use a "memory" clobber to tell the compiler that
memory is accessed within the inline assembly.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
With CONFIG_VMAP_STACK=y the stack is allocated from the vmalloc space.
Data passed to a hardware or a hypervisor interface that
requires V=R can no longer be allocated on the stack.
Use kmalloc() to get memory for a diag288 command.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Using the serio subsystem now requires the code to be reachable:
x86_64-linux-ld: drivers/platform/x86/amd/pmc.o: in function `amd_pmc_suspend_handler':
pmc.c:(.text+0x86c): undefined reference to `serio_bus'
Add the usual dependency: as other users of serio use 'select'
rather than 'depends on', use the same here.
Fixes: 8e60615e89 ("platform/x86/amd: pmc: Disable IRQ1 wakeup for RN/CZN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230127093950.2368575-1-arnd@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As soon as the first handler or sysfs file is registered
the mutex may get used.
Move the initialization to before any handler registration /
sysfs file creation.
Likewise move the destruction of the mutex to after all
the de-initialization is done.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230130132554.696025-1-hdegoede@redhat.com
Every power mode of static power slider has its own AC and DC power
settings.
When the power source changes from AC to DC, corresponding DC thermals
were not updated from PMF config store and this leads the system to always
run on AC power settings.
Fix it by registering with power_supply notifier and apply DC settings
upon getting notified by the power_supply handler.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-6-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
fscache_create_volume_work() uses wake_up_bit() to wake up the processes
which are waiting for the completion of volume creation. According to
comments in wake_up_bit() and waitqueue_active(), an extra smp_mb() is
needed to guarantee the memory order between FSCACHE_VOLUME_CREATING
flag and waitqueue_active() before invoking wake_up_bit().
Fixing it by using clear_and_wake_up_bit() to add the missing memory
barrier.
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-3-houtao@huaweicloud.com/ # v3
The freeing of relinquished volume will wake up the pending volume
acquisition by using wake_up_bit(), however it is mismatched with
wait_var_event() used in fscache_wait_on_volume_collision() and it will
never wake up the waiter in the wait-queue because these two functions
operate on different wait-queues.
According to the implementation in fscache_wait_on_volume_collision(),
if the wake-up of pending acquisition is delayed longer than 20 seconds
(e.g., due to the delay of on-demand fd closing), the first
wait_var_event_timeout() will timeout and the following wait_var_event()
will hang forever as shown below:
FS-Cache: Potential volume collision new=00000024 old=00000022
......
INFO: task mount:1148 blocked for more than 122 seconds.
Not tainted 6.1.0-rc6+ #1
task:mount state:D stack:0 pid:1148 ppid:1
Call Trace:
<TASK>
__schedule+0x2f6/0xb80
schedule+0x67/0xe0
fscache_wait_on_volume_collision.cold+0x80/0x82
__fscache_acquire_volume+0x40d/0x4e0
erofs_fscache_register_volume+0x51/0xe0 [erofs]
erofs_fscache_register_fs+0x19c/0x240 [erofs]
erofs_fc_fill_super+0x746/0xaf0 [erofs]
vfs_get_super+0x7d/0x100
get_tree_nodev+0x16/0x20
erofs_fc_get_tree+0x20/0x30 [erofs]
vfs_get_tree+0x24/0xb0
path_mount+0x2fa/0xa90
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Considering that wake_up_bit() is more selective, so fix it by using
wait_on_bit() instead of wait_var_event() to wait for the freeing of
relinquished volume. In addition because waitqueue_active() is used in
wake_up_bit() and clear_bit() doesn't imply any memory barrier, use
clear_and_wake_up_bit() to add the missing memory barrier between
cursor->flags and waitqueue_active().
Fixes: 62ab633523 ("fscache: Implement volume registration")
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-2-houtao@huaweicloud.com/ # v3
Commit bc66fa87d4 ("net: phy: Add link between phy dev and mac dev")
introduced a link between net devices and phy devices. It fails to check
whether dev is NULL, leading to a NULL dereference error.
Fixes: bc66fa87d4 ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt entry sets the soft mask to IRQS_ALL_DISABLED to match the
hard irq disabled state. So when should_hard_irq_enable() returns true
because we want PMI interrupts in irq handlers, MSR[EE] is enabled but
PMIs just get soft-masked. Fix this by clearing IRQS_PMI_DISABLED before
enabling MSR[EE].
This also tidies some of the warnings, no need to duplicate them in
both should_hard_irq_enable() and do_hard_irq_enable().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230121100156.2824054-1-npiggin@gmail.com
When PMI interrupts are soft-masked, local_irq_save() will clear the PMI
mask bit, allowing PMIs in and causing a race condition. This causes a
deadlock in native_hpte_insert via hash_preload, which depends on PMIs
being disabled since commit 8b91cee5ea ("powerpc/64s/hash: Make hash
faults work in NMI context"). native_hpte_insert calls local_irq_save().
It's possible the lpar hash code is also affected when tracing is
enabled because __trace_hcall_entry() calls local_irq_save().
Fix this by making arch_local_irq_save() _or_ the IRQS_DISABLED bit into
the mask.
This was found with the stress_hpt option with a kbuild workload running
together with `perf record -g`.
Fixes: f442d00480 ("powerpc/64s: Add support to mask perf interrupts and replay them")
Fixes: 8b91cee5ea ("powerpc/64s/hash: Make hash faults work in NMI context")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Just take the fix without the new warning]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230121095352.2823517-1-npiggin@gmail.com
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
objtool throws the following warning:
arch/powerpc/kvm/booke.o: warning: objtool: kvmppc_fill_pt_regs+0x30:
unannotated intra-function call
Fix the warning by setting the value of 'nip' using the _THIS_IP_ macro,
without using an assembly bl/mflr sequence to save the instruction
pointer.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sathvika Vasireddy <sv@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230128124158.1066251-1-sv@linux.ibm.com
objtool throws the following warning:
arch/powerpc/kernel/head_85xx.o: warning: objtool: .head.text+0x1a6c:
unannotated intra-function call
Fix the warning by annotating KernelSPE symbol with SYM_FUNC_START_LOCAL
and SYM_FUNC_END macros.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sathvika Vasireddy <sv@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230128124138.1066176-1-sv@linux.ibm.com
The dirty log checks are mistakenly testing the first page in the page
table (PT) memory region instead of the page holding the test data
page PTE. This wasn't an issue before commit 406504c7b0 ("KVM:
arm64: Fix S1PTW handling on RO memslots") as all PT pages (including
the first page) were treated as writes.
Fix the page_fault_test dirty logging tests by checking for the right
page: the one for the PTE of the data test page.
Fixes: a4edf25b3e ("KVM: selftests: aarch64: Add dirty logging tests into page_fault_test")
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-4-ricarkol@google.com
Only Stage1 Page table walks (S1PTW) trying to write into a PTE should
result in the PTE page being dirty in the log. However, the dirty log
tests in page_fault_test default to treat all S1PTW accesses as writes.
Fix the relevant tests by asserting dirty pages only for S1PTW writes,
which in these tests only applies to when Hardware management of the Access
Flag is enabled.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-3-ricarkol@google.com
Only Stage1 Page table walks (S1PTW) writing a PTE on an unmapped page
should result in a userfaultfd write. However, the userfaultfd tests in
page_fault_test wrongly assert that any S1PTW is a PTE write.
Fix this by relaxing the read vs. write checks in all userfaultfd
handlers. Note that this is also an attempt to focus less on KVM (and
userfaultfd) behavior, and more on architectural behavior. Also note
that after commit 406504c7b0 ("KVM: arm64: Fix S1PTW handling on RO
memslots"), the userfaultfd fault (S1PTW with AF on an unmaped PTE
page) is actually a read: the translation fault that comes before the
permission fault.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-2-ricarkol@google.com
We don't have a running VCPU context to save vgic3 pending table due
to KVM_DEV_ARM_VGIC_{GRP_CTRL, SAVE_PENDING_TABLES} command on KVM
device "kvm-arm-vgic-v3". The unknown case is caught by kvm-unit-tests.
# ./kvm-unit-tests/tests/its-pending-migration
WARNING: CPU: 120 PID: 7973 at arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3325 \
mark_page_dirty_in_slot+0x60/0xe0
:
mark_page_dirty_in_slot+0x60/0xe0
__kvm_write_guest_page+0xcc/0x100
kvm_write_guest+0x7c/0xb0
vgic_v3_save_pending_tables+0x148/0x2a0
vgic_set_common_attr+0x158/0x240
vgic_v3_set_attr+0x4c/0x5c
kvm_device_ioctl+0x100/0x160
__arm64_sys_ioctl+0xa8/0xf0
invoke_syscall.constprop.0+0x7c/0xd0
el0_svc_common.constprop.0+0x144/0x160
do_el0_svc+0x34/0x60
el0_svc+0x3c/0x1a0
el0t_64_sync_handler+0xb4/0x130
el0t_64_sync+0x178/0x17c
Use vgic_write_guest_lock() to save vgic3 pending table.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230126235451.469087-5-gshan@redhat.com
Currently, the unknown no-running-vcpu sites are reported when a
dirty page is tracked by mark_page_dirty_in_slot(). Until now, the
only known no-running-vcpu site is saving vgic/its tables through
KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_SAVE_TABLES} command on KVM device
"kvm-arm-vgic-its". Unfortunately, there are more unknown sites to
be handled and no-running-vcpu context will be allowed in these
sites: (1) KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_RESTORE_TABLES} command
on KVM device "kvm-arm-vgic-its" to restore vgic/its tables. The
vgic3 LPI pending status could be restored. (2) Save vgic3 pending
table through KVM_DEV_ARM_{VGIC_GRP_CTRL, VGIC_SAVE_PENDING_TABLES}
command on KVM device "kvm-arm-vgic-v3".
In order to handle those unknown cases, we need a unified helper
vgic_write_guest_lock(). struct vgic_dist::save_its_tables_in_progress
is also renamed to struct vgic_dist::save_tables_in_progress.
No functional change intended.
Suggested-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230126235451.469087-3-gshan@redhat.com
Xy writes:
FPGA Manager changes for 6.2-final
stratix10-soc:
- Zheng's change fixes return value check
Intel m10 bmc secure update:
- Ilpo's change fixes probe rollback
All patches have been reviewed on the mailing list, and have been in
the last linux-next releases (as part of our for-6.2 branch)
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.2-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: m10bmc-sec: Fix probe rollback
fpga: stratix10-soc: Fix return value check in s10_ops_write_init()
"tcpdump" is used to capture traffic in these tests while using a random,
temporary and not suffixed file for it. This can interfere with apparmor
configuration where the tool is only allowed to read from files with
'known' extensions.
The MINE type application/vnd.tcpdump.pcap was registered with IANA for
pcap files and .pcap is the extension that is both most common but also
aligned with standard apparmor configurations. See TCPDUMP(8) for more
details.
This improves compatibility with standard apparmor configurations by
using ".pcap" as the file extension for the tests' temporary files.
Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX6 CPU frequency driver sometimes fails to register at boot time
due to nvmem_cell_read_u32() sporadically returning -ENOENT.
This happens because there is a window where __nvmem_device_get() in
of_nvmem_cell_get() is able to return the nvmem device, but as cells
have been setup, nvmem_find_cell_entry_by_node() returns NULL.
The occurs because the nvmem core registration code violates one of the
fundamental principles of kernel programming: do not publish data
structures before their setup is complete.
Fix this by making nvmem core code conform with this principle.
Fixes: eace75cfdc ("nvmem: Add a simple NVMEM framework for nvmem providers")
Cc: stable@vger.kernel.org
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dev_set_name() fails, we leak nvmem->wp_gpio as the cleanup does not
put this. While a minimal fix for this would be to add the gpiod_put()
call, we can do better if we split device_register(), and use the
tested nvmem_release() cleanup code by initialising the device early,
and putting the device.
This results in a slightly larger fix, but results in clear code.
Note: this patch depends on "nvmem: core: initialise nvmem->id early"
and "nvmem: core: remove nvmem_config wp_gpio".
Fixes: 5544e90c81 ("nvmem: core: add error handling for dev_set_name")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[Srini: Fixed subject line and error code handing with wp_gpio while applying.]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SID SRAM on at least some SoCs (A64 and D1) returns different values
when read with bus cycles narrower than 32 bits. This is not immediately
obvious, because memcpy_fromio() uses word-size accesses as long as
enough data is being copied.
The vendor driver always uses 32-bit MMIO reads, so do the same here.
This is faster than the register-based method, which is currently used
as a workaround on A64. And it fixes the values returned on D1, where
the SRAM method was being used.
The special case for the last word is needed to maintain .word_size == 1
for sysfs ABI compatibility, as noted previously in commit de2a3eaea5
("nvmem: sunxi_sid: Optimize register read-out method").
Fixes: 07ae4fde9e ("nvmem: sunxi_sid: Add support for D1 variant")
Cc: stable@vger.kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kornel Dulęba says:
====================
net: wwan: t7xx: Fix Runtime PM implementation
d10b3a695b ("net: wwan: t7xx: Runtime PM") introduced support for
Runtime PM for this driver, but due to a bug in the initialization logic
the usage refcount would never reach 0, leaving the feature unused.
This patchset addresses that, together with a bug found after runtime
suspend was enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For PCI devices the Runtime PM refcount is incremented twice:
1. During device enumeration with a call to pm_runtime_forbid.
2. Just before a driver probe logic is called.
Because of that in order to enable Runtime PM on a given device
we have to call both pm_runtime_allow and pm_runtime_put_noidle,
once it's ready to be runtime suspended.
The former was missing causing the pm refcount to never reach 0.
Fixes: d10b3a695b ("net: wwan: t7xx: Runtime PM")
Signed-off-by: Kornel Dulęba <mindal@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resume device before calling napi_schedule, instead of doing in the napi
poll routine. Polling is done in softrq context. We can't call the PM
resume logic from there as it's blocking and not irq safe.
In order to make it work modify the interrupt handler to be run from irq
handler thread.
Fixes: 5545b7b9f2 ("net: wwan: t7xx: Add NAPI support")
Signed-off-by: Kornel Dulęba <mindal@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe() function is only used for the DP83822 PHY, leaving the
private data pointer uninitialized for the smaller DP83825/26 models.
While all uses of the private data structure are hidden in 82822 specific
callbacks, configuring the interrupt is shared across all models.
This causes a NULL pointer dereference on the smaller PHYs as it accesses
the private data unchecked. Verifying the pointer avoids that.
Fixes: 5dc39fd5ef ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Andre Kalb <andre.kalb@sma.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/Y9FzniUhUtbaGKU7@pc6682
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ASoC: Fixes for v6.2
An unfortunately large batch of fixes here, the numbers amplified
by several repeated fixes for patterns of bugs in multiple
drivers. Most of this is in the x86 drivers which are very
actively developed, the implementation of PCI shutdown is a fix
for issues with spamming warnings into the logs with a leaked
reference to the i915 driver.
If you call listen() and accept() on an already connect()ed
rose socket, accept() can successfully connect.
This is because when the peer socket sends data to sendmsg,
the skb with its own sk stored in the connected socket's
sk->sk_receive_queue is connected, and rose_accept() dequeues
the skb waiting in the sk->sk_receive_queue.
This creates a child socket with the sk of the parent
rose socket, which can cause confusion.
Fix rose_listen() to return -EINVAL if the socket has
already been successfully connected, and add lock_sock
to prevent this issue.
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230125105944.GA133314@ubuntu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent sfc NICs are TSO capable for some tunnel protocols. However, it
was not working properly because the feature was not advertised in
hw_enc_features, but in hw_features only.
Setting up a GENEVE tunnel and using iperf3 to send IPv4 and IPv6 traffic
to the tunnel show, with tcpdump, that the IPv4 packets still had ~64k
size but the IPv6 ones had only ~1500 bytes (they had been segmented by
software, not offloaded). With this patch segmentation is offloaded as
expected and the traffic is correctly received at the other end.
Fixes: 24b2c3751a ("sfc: advertise encapsulated offloads on EF10")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230125143513.25841-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
bpf 2023-01-27
We've added 10 non-merge commits during the last 9 day(s) which contain
a total of 10 files changed, 170 insertions(+), 59 deletions(-).
The main changes are:
1) Fix preservation of register's parent/live fields when copying
range-info, from Eduard Zingerman.
2) Fix an off-by-one bug in bpf_mem_cache_idx() to select the right
cache, from Hou Tao.
3) Fix stack overflow from infinite recursion in sock_map_close(),
from Jakub Sitnicki.
4) Fix missing btf_put() in register_btf_id_dtor_kfuncs()'s error path,
from Jiri Olsa.
5) Fix a splat from bpf_setsockopt() via lsm_cgroup/socket_sock_rcv_skb,
from Kui-Feng Lee.
6) Fix bpf_send_signal[_thread]() helpers to hold a reference on the task,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Fix the kernel crash caused by bpf_setsockopt().
selftests/bpf: Cover listener cloning with progs attached to sockmap
selftests/bpf: Pass BPF skeleton to sockmap_listen ops tests
bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener
bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself
bpf: Add missing btf_put to register_btf_id_dtor_kfuncs
selftests/bpf: Verify copy_register_state() preserves parent/live fields
bpf: Fix to preserve reg parent/live fields when copying range info
bpf: Fix a possible task gone issue with bpf_send_signal[_thread]() helpers
bpf: Fix off-by-one error in bpf_mem_cache_idx()
====================
Link: https://lore.kernel.org/r/20230127215820.4993-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GSO should not merge page pool recycled frames with standard reference
counted frames. Traditionally this didn't occur, at least not often.
However as we start looking at adding support for wireless adapters there
becomes the potential to mix the two due to A-MSDU repartitioning frames in
the receive path. There are possibly other places where this may have
occurred however I suspect they must be few and far between as we have not
seen this issue until now.
Fixes: 53e0961da1 ("page_pool: add frag page recycling support in page pool")
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/167475990764.1934330.11960904198087757911.stgit@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Magnus Karlsson says:
====================
net: xdp: execute xdp_do_flush() before napi_complete_done()
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found in [1].
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in [2].
The drivers have only been compile-tested since I do not own any of
the HW below. So if you are a maintainer, it would be great if you
could take a quick look to make sure I did not mess something up.
Note that these were the drivers I found that violated the ordering by
running a simple script and manually checking the ones that came up as
potential offenders. But the script was not perfect in any way. There
might still be offenders out there, since the script can generate
false negatives.
[1] https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
[2] https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
====================
Link: https://lore.kernel.org/r/20230125074901.2737-1-magnus.karlsson@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: a1e031ffb4 ("dpaa_eth: add XDP_REDIRECT support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: 186b3c998c ("virtio-net: support XDP_REDIRECT")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: a825b611c7 ("net: lan966x: Add support for XDP_REDIRECT")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: d1b25b79e1 ("qede: add .ndo_xdp_xmit() and XDP_REDIRECT support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PF controls the set of queues that the RDMA auxiliary_driver requests
resources from. The set_channel command will alter that pool and trigger a
reconfiguration of the VSI, which breaks RDMA functionality.
Prevent set_channel from executing when RDMA driver bound to auxiliary
device.
Adding a locked variable to pass down the call chain to avoid double
locking the device_lock.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Al Viro said:
"""
Since "vhost/scsi: fix reuse of &vq->iov[out] in response"
we have this:
cmd->tvc_resp_iov = vq->iov[vc.out];
cmd->tvc_in_iovs = vc.in;
combined with
iov_iter_init(&iov_iter, ITER_DEST, &cmd->tvc_resp_iov,
cmd->tvc_in_iovs, sizeof(v_rsp));
in vhost_scsi_complete_cmd_work(). We used to have ->tvc_resp_iov
_pointing_ to vq->iov[vc.out]; back then iov_iter_init() asked to
set an iovec-backed iov_iter over the tail of vq->iov[], with
length being the amount of iovecs in the tail.
Now we have a copy of one element of that array. Fortunately, the members
following it in the containing structure are two non-NULL kernel pointers,
so copy_to_iter() will not copy anything beyond the first iovec - kernel
pointer is not (on the majority of architectures) going to be accepted by
access_ok() in copyout() and it won't be skipped since the "length" (in
reality - another non-NULL kernel pointer) won't be zero.
So it's not going to give a guest-to-qemu escalation, but it's definitely
a bug. Frankly, my preference would be to verify that the very first iovec
is long enough to hold rsp_size. Due to the above, any users that try to
give us vq->iov[vc.out].iov_len < sizeof(struct virtio_scsi_cmd_resp)
would currently get a failure in vhost_scsi_complete_cmd_work()
anyway.
"""
However, the spec doesn't say anything about the legacy descriptor
layout for the respone. So this patch tries to not assume the response
to reside in a single separate descriptor which is what commit
79c14141a4 ("vhost/scsi: Convert completion path to use") tries to
achieve towards to ANY_LAYOUT.
This is done by allocating and using dedicate resp iov in the
command. To be safety, start with UIO_MAXIOV to be consistent with the
limitation that we advertise to the vhost_get_vq_desc().
Testing with the hacked virtio-scsi driver that use 1 descriptor for 1
byte in the response.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes: a77ec83a57 ("vhost/scsi: fix reuse of &vq->iov[out] in response")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230119073647.76467-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Fix the build caused by missing kmsan_handle_dma() and is_power_of_2() that
are used in drivers/virtio/virtio_ring.c.
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Message-Id: <20230110034310.779744-1-mie@igel.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the vhost iotlb is used along with a guest virtual iommu
and the guest gets rebooted, some MISS messages may have been
recorded just before the reboot and spuriously executed by
the virtual iommu after the reboot.
As vhost does not have any explicit reset user API,
VHOST_NET_SET_BACKEND looks a reasonable point where to clear
the pending messages, in case the backend is removed.
Export vhost_clear_msg() and call it in vhost_net_set_backend()
when fd == -1.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Fixes: 6b1e6cc785 ("vhost: new device IOTLB API")
Message-Id: <20230117151518.44725-3-eric.auger@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We change recently the memalloc helper to use
dma_alloc_noncontiguous() and the fallback to get_pages(). Although
lots of issues with IOMMU (or non-IOMMU) have been addressed, but
there seems still a regression on Xen PV. Interestingly, the only
proper way to work is use dma_alloc_coherent(). The use of
dma_alloc_coherent() for SG buffer was dropped as it's problematic on
IOMMU systems. OTOH, Xen PV has a different way, and it's fine to use
the dma_alloc_coherent().
This patch is a workaround for Xen PV. It consists of the following
changes:
- For Xen PV, use only the fallback allocation without
dma_alloc_noncontiguous()
- In the fallback allocation, use dma_alloc_coherent();
the DMA address from dma_alloc_coherent() is returned in get_addr
ops
- The DMA addresses are stored in an array; the first entry stores the
number of allocated pages in lower bits, which are referred at
releasing pages again
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: a8d302a0b7 ("ALSA: memalloc: Revive x86-specific WC page allocations again")
Fixes: 9736a32513 ("ALSA: memalloc: Don't fall back for SG-buffer with IOMMU")
Link: https://lore.kernel.org/r/87tu256lqs.wl-tiwai@suse.de
Link: https://lore.kernel.org/r/20230125153104.5527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel crash was caused by a BPF program attached to the
"lsm_cgroup/socket_sock_rcv_skb" hook, which performed a call to
`bpf_setsockopt()` in order to set the TCP_NODELAY flag as an
example. Flags like TCP_NODELAY can prompt the kernel to flush a
socket's outgoing queue, and this hook
"lsm_cgroup/socket_sock_rcv_skb" is frequently triggered by
softirqs. The issue was that in certain circumstances, when
`tcp_write_xmit()` was called to flush the queue, it would also allow
BH (bottom-half) to run. This could lead to our program attempting to
flush the same socket recursively, which caused a `skbuff` to be
unlinked twice.
`security_sock_rcv_skb()` is triggered by `tcp_filter()`. This occurs
before the sock ownership is checked in `tcp_v4_rcv()`. Consequently,
if a bpf program runs on `security_sock_rcv_skb()` while under softirq
conditions, it may not possess the lock needed for `bpf_setsockopt()`,
thus presenting an issue.
The patch fixes this issue by ensuring that a BPF program attached to
the "lsm_cgroup/socket_sock_rcv_skb" hook is not allowed to call
`bpf_setsockopt()`.
The differences from v1 are
- changing commit log to explain holding the lock of the sock,
- emphasizing that TCP_NODELAY is not the only flag, and
- adding the fixes tag.
v1: https://lore.kernel.org/bpf/20230125000244.1109228-1-kuifeng@meta.com/
Signed-off-by: Kui-Feng Lee <kuifeng@meta.com>
Fixes: 9113d7e48e ("bpf: expose bpf_{g,s}etsockopt to lsm cgroup")
Link: https://lore.kernel.org/r/20230127001732.4162630-1-kuifeng@meta.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
This reverts commit 948e922fc4.
Not all targets that return PQ=1 and PDT=0 should be ignored. While
the SCSI spec is vague in this department, there appears to be a
critical mass of devices which rely on devices being accessible with
this combination of reported values.
Fixes: 948e922fc4 ("scsi: core: map PQ=1, PDT=other values to SCSI_SCAN_TARGET_PRESENT")
Link: https://lore.kernel.org/r/yq1lelrleqr.fsf@ca-mkp.ca.oracle.com
Acked-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Martin Wilck <mwilck@suse.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 622113b9f1 ("drm/ssd130x: Replace simple display helpers with the
atomic helpers") changed the driver to just use the atomic helpers instead
of the simple KMS abstraction layer.
But the commit also made a subtle change on the display power sequence and
initialization order, by moving the ssd130x_power_on() call to the encoder
.atomic_enable handler and the ssd130x_init() call to CRTC .reset handler.
Before this change, both ssd130x_power_on() and ssd130x_init() were called
in the simple display pipeline .enable handler, so the display was already
initialized by the time the SSD130X_DISPLAY_ON command was sent.
For some reasons, it only made the ssd130x SPI driver to fail but the I2C
was still working. That is the reason why the bug was not noticed before.
To revert to the old driver behavior, move the ssd130x_init() call to the
encoder .atomic_enable as well. Besides fixing the panel not being turned
on when using SPI, it also gets rid of the custom CRTC .reset callback.
Fixes: 622113b9f1 ("drm/ssd130x: Replace simple display helpers with the atomic helpers")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125184230.3343206-1-javierm@redhat.com
While looking through legacy platform data users, I noticed that
the DT probing never uses data from the DT properties, as the
platform_data structure gets overwritten directly after it
is initialized.
There have never been any boards defining the platform_data in
the mainline kernel either, so this driver so far only worked
with patched kernels or with the default values.
For the benefit of possible downstream users, fix the DT probe
by no longer overwriting the data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230126162203.2986339-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, when resetting the USB modem via AT commands, the modem is
no longer re-connected.
This problem is caused by the incorrect description of the USB_OTG2_OC
pad. It should have pull-up enabled, hysteresis enabled and the
property 'over-current-active-low' should be passed.
With this change, the USB modem can be successfully re-connected
after a reset.
Cc: stable@vger.kernel.org
Fixes: 9ac0ae97e3 ("ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently if suspending using either freeze or memory state, the fec
driver tries to power down the phy which leads to crash of the kernel
and non-responsible kernel with the following call trace:
[ 24.839889 ] Call trace:
[ 24.839892 ] phy_error+0x18/0x60
[ 24.839898 ] kszphy_handle_interrupt+0x6c/0x80
[ 24.839903 ] phy_interrupt+0x20/0x2c
[ 24.839909 ] irq_thread_fn+0x30/0xa0
[ 24.839919 ] irq_thread+0x178/0x2c0
[ 24.839925 ] kthread+0x154/0x160
[ 24.839932 ] ret_from_fork+0x10/0x20
Since there is currently no functionality in the phy subsystem to power
down phys let's just disable the feature of powering-down the ethernet
phy.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The majority of device trees in arch/arm64/boot/dts/freescale/ are
built around i.MX SoCs with the rest being for Layerscape. Yet, calling
get_maintainers.pl -f on this directory will not match the MAINTAINERS
entry, because the directory name doesn't contain the substring "imx".
Add an explicit file match for the directory and exclude the Layerscape
specific files. This ensures To/Cc is not only generated from git
history, but takes e.g. the R: entries into account as well.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently connect/disconnect of USB cable calls afunc_bind and
eventually increments the bNumEndpoints. Performing multiple
plugin/plugout will increment bNumEndpoints incorrectly, and on
the next plug-in it leads to invalid configuration of descriptor
and hence enumeration fails.
Fix this by resetting the value of bNumEndpoints to 1 on every
afunc_bind call.
Fixes: 40c73b3054 ("usb: gadget: f_uac2: add adaptive sync support for capture")
Cc: stable <stable@kernel.org>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1674631645-28888-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A listening socket linked to a sockmap has its sk_prot overridden. It
points to one of the struct proto variants in tcp_bpf_prots. The variant
depends on the socket's family and which sockmap programs are attached.
A child socket cloned from a TCP listener initially inherits their sk_prot.
But before cloning is finished, we restore the child's proto to the
listener's original non-tcp_bpf_prots one. This happens in
tcp_create_openreq_child -> tcp_bpf_clone.
Today, in tcp_bpf_clone we detect if the child's proto should be restored
by checking only for the TCP_BPF_BASE proto variant. This is not
correct. The sk_prot of listening socket linked to a sockmap can point to
to any variant in tcp_bpf_prots.
If the listeners sk_prot happens to be not the TCP_BPF_BASE variant, then
the child socket unintentionally is left if the inherited sk_prot by
tcp_bpf_clone.
This leads to issues like infinite recursion on close [1], because the
child state is otherwise not set up for use with tcp_bpf_prot operations.
Adjust the check in tcp_bpf_clone to detect all of tcp_bpf_prots variants.
Note that it wouldn't be sufficient to check the socket state when
overriding the sk_prot in tcp_bpf_update_proto in order to always use the
TCP_BPF_BASE variant for listening sockets. Since commit
b8b8315e39 ("bpf, sockmap: Remove unhash handler for BPF sockmap usage")
it is possible for a socket to transition to TCP_LISTEN state while already
linked to a sockmap, e.g. connect() -> insert into map ->
connect(AF_UNSPEC) -> listen().
[1]: https://lore.kernel.org/all/00000000000073b14905ef2e7401@google.com/
Fixes: e80251555f ("tcp_bpf: Don't let child socket inherit parent protocol ops on copy")
Reported-by: syzbot+04c21ed96d861dccc5cd@syzkaller.appspotmail.com
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20230113-sockmap-fix-v2-2-1e0ee7ac2f90@cloudflare.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
__ffs_ep0_queue_wait executes holding the spinlock of &ffs->ev.waitq.lock
and unlocks it after the assignments to usb_request are done.
However in the code if the request is already NULL we bail out returning
-EINVAL but never unlocked the spinlock.
Fix this by adding spin_unlock_irq &ffs->ev.waitq.lock before returning.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/20230124091149.18647-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a10b215325 ("media: vb2: add (un)prepare_streaming queue ops") moved
up the q->streaming = 1 assignment to before the call to vb2_start_streaming().
This does make sense since q->streaming indicates that VIDIOC_STREAMON is called,
and the call to start_streaming happens either at that time or later if
q->min_buffers_needed > 0. So q->streaming should be 1 before start_streaming
is called.
However, it turned out that some drivers use vb2_is_streaming() in buf_queue,
and if q->min_buffers_needed == 0, then that will now return true instead of
false.
So for the time being revert to the original behavior.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: a10b215325 ("media: vb2: add (un)prepare_streaming queue ops")
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On 32-bit architectures with 64-bit resource_size_t, sp_rtc_probe()
causes a compiler warning:
drivers/rtc/rtc-sunplus.c: In function 'sp_rtc_probe':
drivers/rtc/rtc-sunplus.c:243:33: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
243 | dev_dbg(&plat_dev->dev, "res = 0x%x, reg_base = 0x%lx\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The best way to print a resource is the special %pR format string,
and similarly to print a pointer we can use %p and avoid the cast.
Fixes: fad6cbe9b2 ("rtc: Add driver for RTC in Sunplus SP7021")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230117172450.2938962-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Several functions that take part in codec's initialization and removal
are re-used by ASoC codec drivers implementations. Drivers mimic the
behavior of hda_codec_driver_probe/remove() found in
sound/pci/hda/hda_bind.c with their component->probe/remove() instead.
One of the reasons for that is the expectation of
snd_hda_codec_device_new() to receive a valid pointer to an instance of
struct snd_card. This expectation can be met only once sound card
components probing commences.
As ASoC sound card may be unbound without codec device being actually
removed from the system, unsetting ->preset in
snd_hda_codec_cleanup_for_unbind() interferes with module unload -> load
scenario causing null-ptr-deref. Preset is assigned only once, during
device/driver matching whereas ASoC codec driver's module reloading may
occur several times throughout the lifetime of an audio stack.
Suggested-by: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230119143235.1159814-1-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch that fixed string control support somehow got mangled when it was
merged in mainline: the added line ended up in the wrong place.
Fix this.
Fixes: 73278d4833 ("media: v4l2-ctrls-api.c: add back dropped ctrl->is_new = 1")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Using kunit_fail_current_test() in a loadable module causes a link
error like:
ERROR: modpost: "kunit_running" [drivers/gpu/drm/vc4/vc4.ko] undefined!
Export the symbol to allow using it from modules.
Fixes: da43ff045c ("drm/vc4: tests: Fail the current test if we access a register")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
We take the BTF reference before we register dtors and we need
to put it back when it's done.
We probably won't se a problem with kernel BTF, but module BTF
would stay loaded (because of the extra ref) even when its module
is removed.
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Fixes: 5ce937d613 ("bpf: Populate pairs of btf_id and destructor kfunc in btf")
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20230120122148.1522359-1-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When use tools/testing/selftests/kselftest_install.sh to make the
kselftest-list.txt under tools/testing/selftests/kselftest_install.
Then use tools/testing/selftests/kselftest_install/run_kselftest.sh to run
all the kselftests in kselftest-list.txt, it will be blocked by case
"filesystems/fat: run_fat_tests.sh" with "Warning: file run_fat_tests.sh
is not executable", so grant executable permission to run_fat_tests.sh to
fix this issue.
Link: https://lkml.kernel.org/r/dfdbba6df8a1ab34bb1e81cd8bd7ca3f9ed5c369.1673424747.git.pengfei.xu@intel.com
Fixes: dd7c9be330 ("selftests/filesystems: add a vfat RENAME_EXCHANGE test")
Signed-off-by: Pengfei Xu <pengfei.xu@intel.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Eduard Zingerman says:
====================
Struct bpf_reg_state is copied directly in several places including:
- check_stack_write_fixed_off() (via save_register_state());
- check_stack_read_fixed_off();
- find_equal_scalars().
However, a literal copy of this struct also copies the following fields:
struct bpf_reg_state {
...
struct bpf_reg_state *parent;
...
enum bpf_reg_liveness live;
...
};
This breaks register parentage chain and liveness marking logic.
The commit message for the first patch has a detailed example.
This patch-set replaces direct copies with a call to a function
copy_register_state(dst,src), which preserves 'parent' and 'live'
fields of the 'dst'.
The fix comes with a significant verifier runtime penalty for some
selftest binaries listed in tools/testing/selftests/bpf/veristat.cfg
and cilium BPF binaries (see [1]):
$ ./veristat -e file,prog,states -C -f 'states_diff>10' master-baseline.log current.log
File Program States (A) States (B) States (DIFF)
-------------------------- -------------------------------- ---------- ---------- ---------------
bpf_host.o tail_handle_ipv4_from_host 231 299 +68 (+29.44%)
bpf_host.o tail_handle_nat_fwd_ipv4 1088 1320 +232 (+21.32%)
bpf_host.o tail_handle_nat_fwd_ipv6 716 729 +13 (+1.82%)
bpf_host.o tail_nodeport_nat_ingress_ipv4 281 314 +33 (+11.74%)
bpf_host.o tail_nodeport_nat_ingress_ipv6 245 256 +11 (+4.49%)
bpf_lxc.o tail_handle_nat_fwd_ipv4 1088 1320 +232 (+21.32%)
bpf_lxc.o tail_handle_nat_fwd_ipv6 716 729 +13 (+1.82%)
bpf_lxc.o tail_ipv4_ct_egress 239 262 +23 (+9.62%)
bpf_lxc.o tail_ipv4_ct_ingress 239 262 +23 (+9.62%)
bpf_lxc.o tail_ipv4_ct_ingress_policy_only 239 262 +23 (+9.62%)
bpf_lxc.o tail_ipv6_ct_egress 181 195 +14 (+7.73%)
bpf_lxc.o tail_ipv6_ct_ingress 181 195 +14 (+7.73%)
bpf_lxc.o tail_ipv6_ct_ingress_policy_only 181 195 +14 (+7.73%)
bpf_lxc.o tail_nodeport_nat_ingress_ipv4 281 314 +33 (+11.74%)
bpf_lxc.o tail_nodeport_nat_ingress_ipv6 245 256 +11 (+4.49%)
bpf_overlay.o tail_handle_nat_fwd_ipv4 799 829 +30 (+3.75%)
bpf_overlay.o tail_nodeport_nat_ingress_ipv4 281 314 +33 (+11.74%)
bpf_overlay.o tail_nodeport_nat_ingress_ipv6 245 256 +11 (+4.49%)
bpf_sock.o cil_sock4_connect 47 70 +23 (+48.94%)
bpf_sock.o cil_sock4_sendmsg 45 68 +23 (+51.11%)
bpf_sock.o cil_sock6_post_bind 31 42 +11 (+35.48%)
bpf_xdp.o tail_lb_ipv4 4413 6457 +2044 (+46.32%)
bpf_xdp.o tail_lb_ipv6 6876 7249 +373 (+5.42%)
test_cls_redirect.bpf.o cls_redirect 4704 4799 +95 (+2.02%)
test_tcp_hdr_options.bpf.o estab 180 206 +26 (+14.44%)
xdp_synproxy_kern.bpf.o syncookie_tc 21059 21485 +426 (+2.02%)
xdp_synproxy_kern.bpf.o syncookie_xdp 21857 23122 +1265 (+5.79%)
-------------------------- -------------------------------- ---------- ---------- ---------------
I looked through verification log for bpf_xdp.o tail_lb_ipv4 program in
order to identify the reason for ~50% visited states increase.
The slowdown is triggered by a difference in handling of three stack slots:
fp-56, fp-72 and fp-80, with the main difference coming from fp-72.
In fact the following change removes all the difference:
@@ -3256,7 +3256,10 @@ static void save_register_state(struct bpf_func_state *state,
{
int i;
- copy_register_state(&state->stack[spi].spilled_ptr, reg);
+ if ((spi == 6 /*56*/ || spi == 8 /*72*/ || spi == 9 /*80*/) && size != BPF_REG_SIZE)
+ state->stack[spi].spilled_ptr = *reg;
+ else
+ copy_register_state(&state->stack[spi].spilled_ptr, reg);
For fp-56 I found the following pattern for divergences between
verification logs with and w/o this patch:
- At some point insn 1862 is reached and checkpoint is created;
- At some other point insn 1862 is reached again:
- with this patch:
- the current state is considered *not* equivalent to the old checkpoint;
- the reason for mismatch is the state of fp-56:
- current state: fp-56=????mmmm
- checkpoint: fp-56_rD=mmmmmmmm
- without this patch the current state is considered equivalent to the
checkpoint, the fp-56 is not present in the checkpoint.
Here is a fragment of the verification log for when the checkpoint in
question created at insn 1862:
checkpoint 1862: ... fp-56=mmmmmmmm ...
1862: ...
1863: ...
1864: (61) r1 = *(u32 *)(r0 +0)
1865: ...
1866: (63) *(u32 *)(r10 -56) = r1 ; R1_w=scalar(...) R10=fp0 fp-56=
1867: (bf) r2 = r10 ; R2_w=fp0 R10=fp0
1868: (07) r2 += -56 ; R2_w=fp-56
; return map_lookup_elem(&LB4_BACKEND_MAP_V2, &backend_id);
1869: (18) r1 = 0xffff888100286000 ; R1_w=map_ptr(off=0,ks=4,vs=8,imm=0)
1871: (85) call bpf_map_lookup_elem#1
- Without this patch:
- at insn 1864 r1 liveness is set to REG_LIVE_WRITTEN;
- at insn 1866 fp-56 liveness is set REG_LIVE_WRITTEN mark because
of the direct r1 copy in save_register_state();
- at insn 1871 REG_LIVE_READ is not propagated to fp-56 at
checkpoint 1862 because of the REG_LIVE_WRITTEN mark;
- eventually fp-56 is pruned from checkpoint at 1862 in
clean_func_state().
- With this patch:
- at insn 1864 r1 liveness is set to REG_LIVE_WRITTEN;
- at insn 1866 fp-56 liveness is *not* set to REG_LIVE_WRITTEN mark
because write size is not equal to BPF_REG_SIZE;
- at insn 1871 REG_LIVE_READ is propagated to fp-56 at checkpoint 1862.
Hence more states have to be visited by verifier with this patch compared
to current master.
Similar patterns could be found for both fp-72 and fp-80, although these
are harder to track trough the log because of a big number of insns between
slot write and bpf_map_lookup_elem() call triggering read mark, boils down
to the following C code:
struct ipv4_frag_id frag_id = {
.daddr = ip4->daddr,
.saddr = ip4->saddr,
.id = ip4->id,
.proto = ip4->protocol,
.pad = 0,
};
...
map_lookup_elem(..., &frag_id);
Where:
- .id is mapped to fp-72, write of size u16;
- .saddr is mapped to fp-80, write of size u32.
This patch-set is a continuation of discussion from [2].
Changes v1 -> v2 (no changes in the code itself):
- added analysis for the tail_lb_ipv4 verification slowdown;
- rebase against fresh master branch.
[1] git@github.com:anakryiko/cilium.git
[2] https://lore.kernel.org/bpf/517af2c57ee4b9ce2d96a8cf33f7295f2d2dfe13.camel@gmail.com/
====================
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Register range information is copied in several places. The intent is
to transfer range/id information from one register/stack spill to
another. Currently this is done using direct register assignment, e.g.:
static void find_equal_scalars(..., struct bpf_reg_state *known_reg)
{
...
struct bpf_reg_state *reg;
...
*reg = *known_reg;
...
}
However, such assignments also copy the following bpf_reg_state fields:
struct bpf_reg_state {
...
struct bpf_reg_state *parent;
...
enum bpf_reg_liveness live;
...
};
Copying of these fields is accidental and incorrect, as could be
demonstrated by the following example:
0: call ktime_get_ns()
1: r6 = r0
2: call ktime_get_ns()
3: r7 = r0
4: if r0 > r6 goto +1 ; r0 & r6 are unbound thus generated
; branch states are identical
5: *(u64 *)(r10 - 8) = 0xdeadbeef ; 64-bit write to fp[-8]
--- checkpoint ---
6: r1 = 42 ; r1 marked as written
7: *(u8 *)(r10 - 8) = r1 ; 8-bit write, fp[-8] parent & live
; overwritten
8: r2 = *(u64 *)(r10 - 8)
9: r0 = 0
10: exit
This example is unsafe because 64-bit write to fp[-8] at (5) is
conditional, thus not all bytes of fp[-8] are guaranteed to be set
when it is read at (8). However, currently the example passes
verification.
First, the execution path 1-10 is examined by verifier.
Suppose that a new checkpoint is created by is_state_visited() at (6).
After checkpoint creation:
- r1.parent points to checkpoint.r1,
- fp[-8].parent points to checkpoint.fp[-8].
At (6) the r1.live is set to REG_LIVE_WRITTEN.
At (7) the fp[-8].parent is set to r1.parent and fp[-8].live is set to
REG_LIVE_WRITTEN, because of the following code called in
check_stack_write_fixed_off():
static void save_register_state(struct bpf_func_state *state,
int spi, struct bpf_reg_state *reg,
int size)
{
...
state->stack[spi].spilled_ptr = *reg; // <--- parent & live copied
if (size == BPF_REG_SIZE)
state->stack[spi].spilled_ptr.live |= REG_LIVE_WRITTEN;
...
}
Note the intent to mark stack spill as written only if 8 bytes are
spilled to a slot, however this intent is spoiled by a 'live' field copy.
At (8) the checkpoint.fp[-8] should be marked as REG_LIVE_READ but
this does not happen:
- fp[-8] in a current state is already marked as REG_LIVE_WRITTEN;
- fp[-8].parent points to checkpoint.r1, parentage chain is used by
mark_reg_read() to mark checkpoint states.
At (10) the verification is finished for path 1-10 and jump 4-6 is
examined. The checkpoint.fp[-8] never gets REG_LIVE_READ mark and this
spill is pruned from the cached states by clean_live_states(). Hence
verifier state obtained via path 1-4,6 is deemed identical to one
obtained via path 1-6 and program marked as safe.
Note: the example should be executed with BPF_F_TEST_STATE_FREQ flag
set to force creation of intermediate verifier states.
This commit revisits the locations where bpf_reg_state instances are
copied and replaces the direct copies with a call to a function
copy_register_state(dst, src) that preserves 'parent' and 'live'
fields of the 'dst'.
Fixes: 679c782de1 ("bpf/verifier: per-register parent pointers")
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20230106142214.1040390-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
snd_hda_get_connections() can return a negative error code.
It may lead to accessing 'conn' array at a negative index.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Artemii Karasev <karasev@ispras.ru>
Fixes: 30b4503378 ("ALSA: hda - Expose secret DAC-AA connection of some VIA codecs")
Link: https://lore.kernel.org/r/20230119082259.3634-1-karasev@ispras.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__USE_GNU should be an internal macro only used inside glibc. Either
memfd_create() or fallocate() requires _GNU_SOURCE per man page, where
__USE_GNU will further be defined by glibc headers include/features.h:
#ifdef _GNU_SOURCE
# define __USE_GNU 1
#endif
This fixes:
>> hugetlb-madvise.c:20: warning: "__USE_GNU" redefined
20 | #define __USE_GNU
|
In file included from /usr/include/x86_64-linux-gnu/bits/libc-header-start.h:33,
from /usr/include/stdlib.h:26,
from hugetlb-madvise.c:16:
/usr/include/features.h:407: note: this is the location of the previous definition
407 | # define __USE_GNU 1
|
Link: https://lkml.kernel.org/r/Y8V9z+z6Tk7NetI3@x1n
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch should harden commit 15520a3f04 ("mm: use pte markers for
swap errors") on using pte markers for swapin errors on a few corner
cases.
1. Propagate swapin errors across fork()s: if there're swapin errors in
the parent mm, after fork()s the child should sigbus too when an error
page is accessed.
2. Fix a rare condition race in pte_marker_clear() where a uffd-wp pte
marker can be quickly switched to a swapin error.
3. Explicitly ignore swapin error pte markers in change_protection().
I mostly don't worry on (2) or (3) at all, but we should still have them.
Case (1) is special because it can potentially cause silent data corrupt
on child when parent has swapin error triggered with swapoff, but since
swapin error is rare itself already it's probably not easy to trigger
either.
Currently there is a priority difference between the uffd-wp bit and the
swapin error entry, in which the swapin error always has higher priority
(e.g. we don't need to wr-protect a swapin error pte marker).
If there will be a 3rd bit introduced, we'll probably need to consider a
more involved approach so we may need to start operate on the bits. Let's
leave that for later.
This patch is tested with case (1) explicitly where we'll get corrupted
data before in the child if there's existing swapin error pte markers, and
after patch applied the child can be rightfully killed.
We don't need to copy stable for this one since 15520a3f04 just landed
as part of v6.2-rc1, only "Fixes" applied.
Link: https://lkml.kernel.org/r/20221214200453.1772655-3-peterx@redhat.com
Fixes: 15520a3f04 ("mm: use pte markers for swap errors")
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
This series contains one fix (first patch) followed by a nice to have safety
belts in case we get a widget from topology which is not handled by SOF and will
not have corresponding swidget associated with.
This patch is fix for Linux kernel v2.6.33 or later.
For request subaction to IEC 61883-1 FCP region, Linux FireWire subsystem
have had an issue of use-after-free. The subsystem allows multiple
user space listeners to the region, while data of the payload was likely
released before the listeners execute read(2) to access to it for copying
to user space.
The issue was fixed by a commit 281e20323a ("firewire: core: fix
use-after-free regression in FCP handler"). The object of payload is
duplicated in kernel space for each listener. When the listener executes
ioctl(2) with FW_CDEV_IOC_SEND_RESPONSE request, the object is going to
be released.
However, it causes memory leak since the commit relies on call of
release_request() in drivers/firewire/core-cdev.c. Against the
expectation, the function is never called due to the design of
release_client_resource(). The function delegates release task
to caller when called with non-NULL fourth argument. The implementation
of ioctl_send_response() is the case. It should release the object
explicitly.
This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: 281e20323a ("firewire: core: fix use-after-free regression in FCP handler")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230117090610.93792-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: a164137ce9 ("ASoC: Intel: add machine driver for SOF+ES8336")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 9a87fc1e06 ("ASoC: Intel: bytcr_wm5102: Add machine driver for BYT/WM5102")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: a232b96dce ("ASoC: Intel: bytcr_rt5640: use HID translation util")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 02c0a3b304 ("ASoC: Intel: bytcr_rt5651: add MCLK, quirks and cleanups")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 3c22a73fb8 ("ASoC: Intel: bytcht_es8316: fix HID handling")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 02527c3f23 ("ASoC: amd: add Machine driver for Jadeite platform")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230112112356.67643-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation of rtc-efi is expecting all the 4
time services GET{SET}_TIME{WAKEUP} must be supported by UEFI
firmware. As per the EFI_RT_PROPERTIES_TABLE, the platform
specific implementations can choose to enable selective time
services based on the RTC device capabilities.
This patch does the following changes to provide GET/SET RTC
services on platforms that do not support the WAKEUP feature.
1) Relax time services cap check when creating a platform device.
2) Clear RTC_FEATURE_ALARM bit in the absence of WAKEUP services.
3) Conditional alarm entries in '/proc/driver/rtc'.
Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Link: https://lore.kernel.org/r/20230102230630.192911-1-sdonthineni@nvidia.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of checking the state of various backlight_properties fields
against the memorised state in atmel_lcdfb_info.bl_power,
atmel_bl_update_status() should retrieve the desired state using
backlight_get_brightness (which takes into account the power state,
blanking etc.). This means the explicit checks using props.fb_blank
and props.power can be dropped.
The backlight framework ensures that backlight is never negative, so
the test before reading the brightness from the hardware always ends
up false and the whole block can be removed. The framework retrieves
the brightness from the hardware through atmel_bl_get_brightness()
when necessary.
As a result, bl_power in struct atmel_lcdfb_info is no longer
necessary, so remove that while we're at it. Since we only ever care
about reading the current state in backlight_properties, drop the
updates at the end of the function.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Helge Deller <deller@gmx.de>
linux,keycode should be "linux,keycodes" according binding-doc
Documentation/devicetree/bindings/input/fsl,scu-key.yaml
Fixes: f537ee7f1e ("arm64: dts: freescale: add i.MX8DXL SoC support")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL-terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The following build warnings are seen when running:
make dtbs_check DT_SCHEMA_FILES=fsl-imx-uart.yaml
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dtb: serial@30860000: cts-gpios: False schema does not allow [[33, 3, 1]]
From schema: Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dtb: serial@30860000: rts-gpios: False schema does not allow [[33, 5, 1]]
From schema: Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
...
The imx8m Venice Gateworks boards do not expose the UART RTS and CTS
as native UART pins, so 'uart-has-rtscts' should not be used.
Using 'uart-has-rtscts' with 'rts-gpios' is an invalid combination
detected by serial.yaml.
Fix the problem by removing the incorrect 'uart-has-rtscts' property.
Fixes: 27c8f4ccc1 ("arm64: dts: imx8mm-venice-gw72xx-0x: add dt overlays for serial modes")
Fixes: d9a9a7cf32 ("arm64: dts: imx8m{m,n}-venice-*: add missing uart-has-rtscts property to UARTs")
Fixes: 870f645b39 ("arm64: dts: imx8mp-venice-gw74xx: add WiFi/BT module support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO watchdog property name is 'always-running', not 'always-enabled'.
Use the correct property name and reinstate it into the DT.
Fixes: eff6b33c9c ("arm64: dts: imx8mm: Remove watchdog always-enabled property from eDM SBC")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following kernel linkage error:
st_lsm6dsx_core.o: in function `st_lsm6dsx_sw_buffers_setup':
st_lsm6dsx_core.c:2578: undefined reference to `devm_iio_triggered_buffer_setup_ext'
is caused by the fact that the object owning devm_iio_triggered_buffer_setup_ext()
(drivers/iio/buffer/industrialio-triggered-buffer.o) is allowed to be
built as module when its user (drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c)
is built-in.
The st_lsm6dsx driver already has a "select IIO_BUFFER", so add another
select for IIO_TRIGGERED_BUFFER, to make that option follow what is set
for the st_lsm6dsx driver. This is similar to what other iio drivers do.
Fixes: 2cfb2180c3 ("iio: imu: st_lsm6dsx: introduce sw trigger support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230103130348.1733467-1-vladimir.oltean@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
irq flood happen when run
cat /sys/bus/iio/devices/iio:device0/in_voltage1_raw
imx8qxp_adc_read_raw()
{
...
enable irq
/* adc start */
writel(1, adc->regs + IMX8QXP_ADR_ADC_SWTRIG);
^^^^ trigger irq flood.
wait_for_completion_interruptible_timeout();
readl(adc->regs + IMX8QXP_ADR_ADC_RESFIFO);
^^^^ clear irq here.
...
}
There is only FIFO watermark interrupt at this ADC controller.
IRQ line will be assert until software read data from FIFO.
So IRQ flood happen during wait_for_completion_interruptible_timeout().
Move FIFO read into irq handle to avoid irq flood.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Cc: stable@vger.kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20221201140110.2653501-1-Frank.Li@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
