The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]---
Cc: stable <stable@kernel.org>
Fixes: 0666e3fe95 ("serial: sh-sci: Add support for RZ/T2H SCI")
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Link: https://patch.msgid.link/20250923154707.1089900-1-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to provide an easier support to more different SCI
controllers, like the RZ/T2H one.
The existing .data field of_sci_match is changed to a structure containing
all what that can be statically initialized, and avoid a call to
'sci_probe_regmap', in both 'sci_init_single', and 'early_console_setup'.
'sci_probe_regmap' is now assumed to be called in the only case where the
device description is from a board file instead of a dts.
In this way, there is no need to patch 'sci_probe_regmap' for adding new
SCI type, and also, the specific sci_port_params for a new SCI type can be
provided by an external file.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-10-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim here is to prepare support for new sci controllers like
the T2H/RSCI whose registers are too much different for being
handled in common code.
This named serial controller also has 32 bits register,
so some return types had to be changed.
The needed generic functions are no longer static, with prototypes
defined in sh-sci-common.h so that they can be used from specific
implementation in a separate file, to keep this driver as little
changed as possible.
For doing so, a set of 'ops' is added to struct sci_port.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thierry Bultel <thierry.bultel.yh@bp.renesas.com>
Link: https://lore.kernel.org/r/20250403212919.1137670-9-thierry.bultel.yh@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On (H)SCIF with a Baud Rate Generator for External Clock (BRG), there
are multiple ways to configure the requested serial speed. If firmware
uses a different method than Linux, and if any debug info is printed
after the Bit Rate Register (SCBRR) is restored, but before termios is
reconfigured (which configures the alternative method), the system may
lock-up during resume.
Fix this by saving and restoring the contents of the BRG Frequency
Division (SCDL) and Clock Select (SCCKS) registers as well.
Also save and restore the HSCIF's Sampling Rate Register (HSSRR), which
configures the sampling point, and the SCIFA/SCIFB's Serial Port Control
and Data Registers (SCPCR/SCPDR), which configure the optional control
flow signals.
After this, all registers that are not saved/restored are either:
- read-only,
- write-only,
- status registers containing flags with clear-after-set semantics,
- FIFO Data Count Trigger registers, which do not matter much for
the serial console.
Fixes: 22a6984c5b ("serial: sh-sci: Update the suspend/resume support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/11c2eab45d48211e75d8b8202cce60400880fe55.1741114989.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/G3S supports a power saving mode where power to most of the
SoC components is turned off. When returning from this power saving mode,
SoC components need to be re-configured.
The SCIFs on the Renesas RZ/G3S need to be re-configured as well when
returning from this power saving mode. The sh-sci code already configures
the SCIF clocks, power domain and registers by calling uart_resume_port()
in sci_resume(). On suspend path the SCIF UART ports are suspended
accordingly (by calling uart_suspend_port() in sci_suspend()). The only
missing setting is the reset signal. For this assert/de-assert the reset
signal on driver suspend/resume.
In case the no_console_suspend is specified by the user, the registers need
to be saved on suspend path and restore on resume path. To do this the
sci_console_save()/sci_console_restore() functions were added. There is no
need to cache/restore the status or FIFO registers. Only the control
registers. The registers that will be saved/restored on suspend/resume are
specified by the struct sci_suspend_regs data structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250207113313.545432-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.
The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:
uart_add_one_port() ->
serial_ctrl_register_port() ->
serial_core_register_port() ->
serial_core_port_device_add() ->
serial_base_port_add() ->
device_add() ->
bus_probe_device() ->
device_initial_probe() ->
__device_attach() ->
// ...
if (dev->p->dead) {
// ...
} else if (dev->driver) {
// ...
} else {
// ...
pm_request_idle(dev);
// ...
}
The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.
The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.
To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().
Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:
sci_ports[0] = port B
sci_ports[X] = port A
In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).
To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.
To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/tty/serial to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241007205803.444994-7-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/V2H(P) SoC with earlycon.
The SCIF interface in the Renesas RZ/V2H(P) is similar to that available
in the RZ/G2L (R9A07G044) SoC, with the following differences:
- RZ/V2H(P) SoC has three additional interrupts: one for Tx end/Rx ready
and two for Rx and Tx buffer full, all of which are edge-triggered.
- RZ/V2H(P) supports asynchronous mode, whereas RZ/G2L supports both
synchronous and asynchronous modes.
- There are differences in the configuration of certain registers such
as SCSMR, SCFCR, and SCSPTR between the two SoCs.
To handle these differences on RZ/V2H(P) SoC SCIx_RZV2H_SCIF_REGTYPE
is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240604170513.522631-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike the 8250 serial driver complex, the sh-sci driver uses only a
single pair of functions to read and write serial port registers.
Hence there is no need to incur the overhead of calling them through
indirection, like the serial_port_{in,out}() wrappers do.
Replace all calls to these wrappers by direct calls to
sci_serial_{in,out}().
Remove the setup of the uart_port.serial_{in,out}() callbacks. After
removal of all calls to serial_port_{in,out}() in the sh-sci driver, the
only remaining user is uart_xchar_out(), which the sh-sci driver does
not use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/51e79d601cb9d9d63822d3773d3cf05a96868612.1709548811.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231110152927.70601-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-61-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx
Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
