This structure is used only in bareudp.c.
While there, adjust include files: we need netdevice.h, not skbuff.h.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DMA threshold mode, frame underflow errors may sometimes occur when
the TC(threshold control) value is not enough. The TC value need to be
bumped up in this case.
There is no underflow interrupt bit on DMA_CH(#i)_Status of dwmac4, so
the DMA threshold cannot be bumped up in stmmac_dma_interrupt(). The
i.mx8mp board observed an underflow error while running NFS boot, the
NFS rootfs could not be mounted.
The underflow error can be got from the DMA descriptor TDES3 on dwmac4.
This patch bump up tc value once underflow error is got from TDES3.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver messes with the tagging protocol's state when PTP RX
timestamping is enabled/disabled. This is fundamentally necessary
because the tagger needs to know what to do when it receives a PTP
packet. If RX timestamping is enabled, then a metadata follow-up frame
is expected, and this holds the (partial) timestamp. So the tagger plays
hide-and-seek with the network stack until it also gets the metadata
frame, and then presents a single packet, the timestamped PTP packet.
But when RX timestamping isn't enabled, there is no metadata frame
expected, so the hide-and-seek game must be turned off and the packet
must be delivered right away to the network stack.
Considering this, we create a pseudo isolation by devising two tagger
methods callable by the switch: one to get the RX timestamping state,
and one to set it. Since we can't export symbols between the tagger and
the switch driver, these methods are exposed through function pointers.
After this change, the public portion of the sja1105_tagger_data
contains only function pointers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6d709cadfd.
The above change was done to avoid calling symbols exported by the
switch driver from the tagging protocol driver.
With the tagger-owned storage model, we have a new option on our hands,
and that is for the switch driver to provide a data consumer handler in
the form of a function pointer inside the ->connect_tag_protocol()
method. Having a function pointer avoids the problems of the exported
symbols approach.
By creating a handler for metadata frames holding TX timestamps on
SJA1110, we are able to eliminate an skb queue from the tagger data, and
replace it with a simple, and stateless, function pointer. This skb
queue is now handled exclusively by sja1105_ptp.c, which makes the code
easier to follow, as it used to be before the reverted patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, struct sja1105_tagger_data is a part of struct
sja1105_private, and is used by the sja1105 driver to populate dp->priv.
With the movement towards tagger-owned storage, the sja1105 driver
should not be the owner of this memory.
This change implements the connection between the sja1105 switch driver
and its tagging protocol, which means that sja1105_tagger_data no longer
stays in dp->priv but in ds->tagger_data, and that the sja1105 driver
now only populates the sja1105_port_deferred_xmit callback pointer.
The kthread worker is now the responsibility of the tagger.
The sja1105 driver also alters the tagger's state some more, especially
with regard to the PTP RX timestamping state. This will be fixed up a
bit in further changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamp ID is incremented by the SJA1110 PTP timestamping
callback (->port_tx_timestamp) for every packet, when cloning it.
It isn't used by the tagger at all, even though it sits inside the
struct sja1105_tagger_data.
Also, serialization to this structure is currently done through
tagger_data->meta_lock, which is a cheap hack because the meta_lock
isn't used for anything else on SJA1110 (sja1105_rcv_meta_state_machine
isn't called).
This change moves ts_id from sja1105_tagger_data to sja1105_private and
introduces a dedicated spinlock for it, also in sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The design of the sja1105 tagger dp->priv is that each port has a
separate struct sja1105_port, and the sp->data pointer points to a
common struct sja1105_tagger_data.
We have removed all per-port members accessible by the tagger, and now
only struct sja1105_tagger_data remains. Make dp->priv point directly to
this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tagger property is in fact not used at all by the tagger, only by
the switch driver. Therefore it makes sense to be moved to
sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ocelot-8021q driver was converted to deferred xmit as part of
commit 8d5f7954b7 ("net: dsa: felix: break at first CPU port during
init and teardown"), the deferred implementation was deliberately made
subtly different from what sja1105 has.
The implementation differences lied on the following observations:
- There might be a race between these two lines in tag_sja1105.c:
skb_queue_tail(&sp->xmit_queue, skb_get(skb));
kthread_queue_work(sp->xmit_worker, &sp->xmit_work);
and the skb dequeue logic in sja1105_port_deferred_xmit(). For
example, the xmit_work might be already queued, however the work item
has just finished walking through the skb queue. Because we don't
check the return code from kthread_queue_work, we don't do anything if
the work item is already queued.
However, nobody will take that skb and send it, at least until the
next timestampable skb is sent. This creates additional (and
avoidable) TX timestamping latency.
To close that race, what the ocelot-8021q driver does is it doesn't
keep a single work item per port, and a skb timestamping queue, but
rather dynamically allocates a work item per packet.
- It is also unnecessary to have more than one kthread that does the
work. So delete the per-port kthread allocations and replace them with
a single kthread which is global to the switch.
This change brings the two implementations in line by applying those
observations to the sja1105 driver as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is not necessary and complicates the conversion of this driver
to tagger-owned memory. If there is a PTP packet that is sent
concurrently with the port getting disabled, the deferred xmit mechanism
is robust enough to time out when it sees that it hasn't been delivered,
and recovers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix driver makes very light use of dp->priv, and the tagger is
effectively stateless. dp->priv is practically only needed to set up a
callback to perform deferred xmit of PTP and STP packets using the
ocelot-8021q tagging protocol (the main ocelot tagging protocol makes no
use of dp->priv, although this driver sets up dp->priv irrespective of
actual tagging protocol in use).
struct felix_port (what used to be pointed to by dp->priv) is removed
and replaced with a two-sided structure. The public side of this
structure, visible to the switch driver, is ocelot_8021q_tagger_data.
The private side is ocelot_8021q_tagger_private, and the latter
structure physically encapsulates the former. The public half of the
tagger data structure can be accessed through a helper of the same name
(ocelot_8021q_tagger_data) which also sanity-checks the protocol
currently in use by the switch. The public/private split was requested
by Andrew Lunn.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical mv88e6xxx switch tree like this:
CPU
| .----.
.--0--. | .--0--.
| sw0 | | | sw1 |
'-1-2-' | '-1-2-'
'---'
If sw1p{1,2} are added to a bridge that sw0p1 is not a part of, sw0
still needs to add a crosschip PVT entry for the virtual DSA device
assigned to represent the bridge.
Fixes: ce5df6894a ("net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet frames can be extracted or injected autonomously to or from
the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list
data structures in memory are used for injecting or extracting Ethernet
frames. The FDMA generates interrupts when frame extraction or
injection is done and when the linked lists need updating.
The FDMA is shared between all the ethernet ports of the switch and
uses a linked list of descriptors (DCB) to inject and extract packets.
Before adding descriptors, the FDMA channels must be stopped. It would
be inefficient to do that each time a descriptor would be added so the
channels are restarted only once they stopped.
Both channels uses ring-like structure to feed the DCBs to the FDMA.
head and tail are never touched by hardware and are completely handled
by the driver. On top of that, page recycling has been added and is
mostly taken from gianfar driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit adds support for changing MTU for the ocelot register based
interface. For ocelot, JUMBO frame size can be set up to 25000 bytes
but has been set to 9000 which is a saner value and allows for maximum
gain of performance with FDMA.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support PTP in FDMA, PTP handling code is needed. Since
this is the same as for register-based extraction, export it with
a new ocelot_ptp_rx_timestamp() function.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDMA will need this code to prepare the injection frame header when
sending SKBs. Move this code into ocelot_ifh_port_set() and add
conditional IFH setting for vlan and rew op if they are not set.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If there is no active IP session (interface up & running) then
release the data channel.
Use nr_sessions variable to track current active IP sessions.
If the count drops to 0, then send pipe close ctrl message to
release the data channel.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ag71xx may have a PCS, but it does not appear to support configuration
of the PCS in the current code. The functions to get its state merely
report that the link is down, and the AN restart function is empty.
Since neither of these functions will be called unless phylink's legacy
flag is set, we can safely remove these functions and indicate this is
a modern driver.
Should PCS support be added later, it will need to be modelled using
the phylink_pcs support rather than operating as a legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the legacy flag to indicate whether we should operate in legacy
mode. This allows us to stop using the presence of a PCS as an
indicator to the age of the phylink user, and make PCS presence
optional.
Legacy mode involves:
1) calling mac_config() whenever the link comes up
2) calling mac_config() whenever the inband advertisement changes,
possibly followed by a call to mac_an_restart()
3) making use of mac_an_restart()
4) making use of mac_pcs_get_state()
All the above functionality was moved to a seperate "PCS" block of
operations in March 2020.
Update the documents to indicate that the differences that this flag
makes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mtk_eth_soc has not been updated for commit 7cceb599d1 ("net: phylink:
avoid mac_config calls"), and makes use of state->speed and
state->duplex in contravention of the phylink documentation. This makes
reliant on the legacy behaviours, so mark it as a legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martyn Welch reports that his CPU port is unable to link where it has
been necessary to use one of the switch ports with an internal PHY for
the CPU port. The reason behind this is the port control register is
left forcing the link down, preventing traffic flow.
This occurs because during initialisation, phylink expects the link to
be down, and DSA forces the link down by synthesising a call to the
DSA drivers phylink_mac_link_down() method, but we don't touch the
forced-link state when we later reconfigure the port.
Resolve this by also unforcing the link state when we are operating in
PHY mode and the PPU is set to poll the PHY to retrieve link status
information.
Reported-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Fixes: 3be98b2d5f ("net: dsa: Down cpu/dsa ports phylink will control")
Cc: <stable@vger.kernel.org> # 5.7: 2b29cb9e3f: net: dsa: mv88e6xxx: fix "don't use PHY_DETECT on internal PHY's"
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1mvFhP-00F8Zb-Ul@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ev_cdev_write_pending flag is preventing a TX message post for
AT port while MBIM transfer is ongoing.
Removed the unnecessary check around control port TX transfer.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devlink initialization flow was overwriting the IP traffic
channel configuration. This was causing wwan0 network interface
to be unusable after fw flash.
When device boots to fully functional mode restore the IP channel
configuration.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In TX packet accumulation flow transport layer is
giving a doorbell to device even though there is
no pending control TX transfer that needs immediate
attention.
Introduced a new hpda_ctrl_pending variable to keep
track of pending control TX transfer. If there is a
pending control TX transfer which needs an immediate
attention only then give a doorbell to device.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In line 800 (#1), nfp_cpp_area_alloc() allocates and initializes a
CPP area structure. But in line 807 (#2), when the cache is allocated
failed, this CPP area structure is not freed, which will result in
memory leak.
We can fix it by freeing the CPP area when the cache is allocated
failed (#2).
792 int nfp_cpp_area_cache_add(struct nfp_cpp *cpp, size_t size)
793 {
794 struct nfp_cpp_area_cache *cache;
795 struct nfp_cpp_area *area;
800 area = nfp_cpp_area_alloc(cpp, NFP_CPP_ID(7, NFP_CPP_ACTION_RW, 0),
801 0, size);
// #1: allocates and initializes
802 if (!area)
803 return -ENOMEM;
805 cache = kzalloc(sizeof(*cache), GFP_KERNEL);
806 if (!cache)
807 return -ENOMEM; // #2: missing free
817 return 0;
818 }
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20211209061511.122535-1-niejianglei2021@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The registration of XDP queue information is incorrect because the
RX queue id we use is invalid. When port->id == 0 it appears to works
as expected yet it's no longer the case when port->id != 0.
The problem arised while using a recent kernel version on the
MACCHIATOBin. This board has several ports:
* eth0 and eth1 are 10Gbps interfaces ; both ports has port->id == 0;
* eth2 is a 1Gbps interface with port->id != 0.
Code from xdp-tutorial (more specifically advanced03-AF_XDP) was used
to test packet capture and injection on all these interfaces. The XDP
kernel was simplified to:
SEC("xdp_sock")
int xdp_sock_prog(struct xdp_md *ctx)
{
int index = ctx->rx_queue_index;
/* A set entry here means that the correspnding queue_id
* has an active AF_XDP socket bound to it. */
if (bpf_map_lookup_elem(&xsks_map, &index))
return bpf_redirect_map(&xsks_map, index, 0);
return XDP_PASS;
}
Starting the program using:
./af_xdp_user -d DEV
Gives the following result:
* eth0 : ok
* eth1 : ok
* eth2 : no capture, no injection
Investigating the issue shows that XDP rx queues for eth2 are wrong:
XDP expects their id to be in the range [0..3] but we found them to be
in the range [32..35].
Trying to force rx queue ids using:
./af_xdp_user -d eth2 -Q 32
fails as expected (we shall not have more than 4 queues).
When we register the XDP rx queue information (using
xdp_rxq_info_reg() in function mvpp2_rxq_init()) we tell it to use
rxq->id as the queue id. This value is computed as:
rxq->id = port->id * max_rxq_count + queue_id
where max_rxq_count depends on the device version. In the MACCHIATOBin
case, this value is 32, meaning that rx queues on eth2 are numbered
from 32 to 35 - there are four of them.
Clearly, this is not the per-port queue id that XDP is expecting:
it wants a value in the range [0..3]. It shall directly use queue_id
which is stored in rxq->logic_rxq -- so let's use that value instead.
rxq->id is left untouched ; its value is indeed valid but it should
not be used in this context.
This is consistent with the remaining part of the code in
mvpp2_rxq_init().
With this change, packet capture is working as expected on all the
MACCHIATOBin ports.
Fixes: b27db2274b ("mvpp2: use page_pool allocator")
Signed-off-by: Louis Amas <louis.amas@eho.link>
Signed-off-by: Emmanuel Deloget <emmanuel.deloget@eho.link>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20211207143423.916334-1-louis.amas@eho.link
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Debugfs interface is optional for the regular modem use. Some distros
and users will want to disable this feature for security or kernel
size reasons. So add a configuration option that allows to completely
disable the debugfs interface of the WWAN devices.
A primary considered use case for this option was embedded firmwares.
For example, in OpenWrt, you can not completely disable debugfs, as a
lot of wireless stuff can only be configured and monitored with the
debugfs knobs. At the same time, reducing the size of a kernel and
modules is an essential task in the world of embedded software.
Disabling the WWAN and IOSM debugfs interfaces allows us to save 50K
(x86-64 build) of space for module storage. Not much, but already
considerable when you only have 16MB of storage.
So it is hard to just disable whole debugfs. Users need some fine
grained set of options to control which debugfs interface is important
and should be available and which is not.
The new configuration symbol is enabled by default and is hidden under
the EXPERT option. So a regular user would not be bothered by another
one configuration question. While an embedded distro maintainer will be
able to a little more reduce the final image size.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The modem traces collection is a device (and so driver) specific option.
Therefore, move the related debugfs files into a driver-specific
subdirectory under the common per WWAN device directory.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Collecting modem firmware traces is optional for the regular modem use.
There are not many reasons for aborting device initialization due to an
inability to initialize the trace port and (or) its debugfs interface.
So, demote the initialization failure erro message into a warning and do
not break the initialization sequence in this case. Rework packet
processing and deinitialization so that they do not crash in case of
uninitialized trace port.
This change is mainly a preparation for an upcoming configuration option
introduction that will help disable driver debugfs functionality.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the channel related structures initialization from
ipc_imem_channel_init() to ipc_trace_init() and call it directly. On the
one hand, this makes the trace port initialization symmetric to the
deitialization, that is, it removes the additional wrapper.
On the other hand, this change consolidates the trace port related code
into a single source file, what facilitates an upcoming disabling of
this functionality by a user choise.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: M Chetan Kumar <m.chetan.kumar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'Commit 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")'
added support for 32Tx/Rx queues. Within that patch, value of
VMXNET3_LINUX_MIN_MSIX_VECT was updated.
However, there is a case (numvcpus = 2) which actually requires 3
intrs which matches VMXNET3_LINUX_MIN_MSIX_VECT which then is
treated as failure by stack to allocate more vectors. This patch
fixes this issue.
Fixes: 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Link: https://lore.kernel.org/r/20211207081737.14000-1-doshir@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
can-next 2021-12-08
The first patch is by Vincent Mailhol and replaces the custom CAN
units with generic one form linux/units.h.
The next 3 patches are by Evgeny Boger and add Allwinner R40 support
to the sun4i CAN driver.
Andy Shevchenko contributes 4 patches to the hi311x CAN driver,
consisting of cleanups and converting the driver to the device
property API.
* tag 'linux-can-next-for-5.17-20211208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: hi311x: hi3110_can_probe(): convert to use dev_err_probe()
can: hi311x: hi3110_can_probe(): make use of device property API
can: hi311x: hi3110_can_probe(): try to get crystal clock rate from property
can: hi311x: hi3110_can_probe(): use devm_clk_get_optional() to get the input clock
ARM: dts: sun8i: r40: add node for CAN controller
can: sun4i_can: add support for R40 CAN controller
dt-bindings: net: can: add support for Allwinner R40 CAN controller
can: bittiming: replace CAN units with the generic ones from linux/units.h
====================
Link: https://lore.kernel.org/r/20211208125055.223141-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix bogus compilter warning in nfnetlink_queue, from Florian Westphal.
2) Don't run conntrack on vrf with !dflt qdisc, from Nicolas Dichtel.
3) Fix nft_pipapo bucket load in AVX2 lookup routine for six 8-bit
groups, from Stefano Brivio.
4) Break rule evaluation on malformed TCP options.
5) Use socat instead of nc in selftests/netfilter/nft_zones_many.sh,
also from Florian
6) Fix KCSAN data-race in conntrack timeout updates, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: conntrack: annotate data-races around ct->timeout
selftests: netfilter: switch zone stress to socat
netfilter: nft_exthdr: break evaluation if setting TCP option fails
selftests: netfilter: Add correctness test for mac,net set type
nft_set_pipapo: Fix bucket load in AVX2 lookup routine for six 8-bit groups
vrf: don't run conntrack on vrf with !dflt qdisc
netfilter: nfnetlink_queue: silence bogus compiler warning
====================
Link: https://lore.kernel.org/r/20211209000847.102598-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-08
Yahui adds re-initialization of Flow Director for VF reset.
Paul restores interrupts when enabling VFs.
Dave re-adds bandwidth check for DCBNL and moves DSCP mode check
earlier in the function.
Jesse prevents reporting of dropped packets that occur during
initialization and fixes reporting of statistics which could occur with
frequent reads.
Michal corrects setting of protocol type for UDP header and fixes lack
of differentiation when adding filters for tunnels.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: safer stats processing
ice: fix adding different tunnels
ice: fix choosing UDP header type
ice: ignore dropped packets during init
ice: Fix problems with DSCP QoS implementation
ice: rearm other interrupt cause register after enabling VFs
ice: fix FDIR init missing when reset VF
====================
Link: https://lore.kernel.org/r/20211208211144.2629867-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
