At present, we have found that there may be a problem of blurred
screen during fast sleep/resume. The direct cause of the blurred
screen is that the IC does not receive 0x28/0x10. Because of the
particularity of the IC, before the panel enters sleep hid must
stop scanning, as i2c_hid_core_suspend before ili9882t_disable.
If move the ili9882t_enter_sleep_mode function to ili9882t_unprepare,
touch reset will pull low before panel entersleep, which does not meet
the timing requirements.. So in order to solve this problem, the IC
can handle it through the exception mechanism when it cannot receive
0x28/0x10 command. Handling exceptions requires a reset 50ms delay.
Refer to vendor detailed analysis [1].
Ilitek vendor also suggested switching the page before entering sleep to
avoid panel IC not receiving 0x28/0x10 command.
Note: 0x28 is display off, 0x10 is sleep in.
[1]: https://github.com/ILITEK-LoganLin/Document/tree/main/ILITEK_Power_Sequence
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013091844.804310-3-yangcong5@huaqin.corp-partner.google.com
Fix flickering of the pinephone's XDB599 panel that happens after
resume.
Extend the delay after issuing the command to exit sleep mode from 60 to
120 msec as per the controller's specification.
Introduce a 120 msec delay after issuing the command to enter sleep
mode. This is needed in order for the controller to reliably finalize
the sleep in sequence before switching of power supply.
In contrast to the JH057N panel, the XBD599 panel does not require a 20
msec delay after initialization and exiting sleep mode. Therefore, move
the delay into the already existing device specific initialization
function.
The XDB599 does not require a 20 msec delay between the SETBGP and
SETVCOM commands. Therefore, remove the delay from the device specific
initialization function.
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Cc: Ondrej Jirman <megi@xff.cz>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213123238.76889-2-frank@oltmanns.dev
Switching to a different reset sequence, enabling IOVCC before enabling
VCC.
There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev
drm-misc-next for v6.7-rc1:
UAPI Changes:
- drm_file owner is now updated during use, in the case of a drm fd
opened by the display server for a client, the correct owner is
displayed.
- Qaic gains support for the QAIC_DETACH_SLICE_BO ioctl to allow bo
recycling.
Cross-subsystem Changes:
- Disable boot logo for au1200fb, mmpfb and unexport logo helpers.
Only fbcon should manage display of logo.
- Update freescale in MAINTAINERS.
- Add some bridge files to bridge in MAINTAINERS.
- Update gma500 driver repo in MAINTAINERS to point to drm-misc.
Core Changes:
- Move size computations to drm buddy allocator.
- Make drm_atomic_helper_shutdown(NULL) a nop.
- Assorted small fixes in drm_debugfs, DP-MST payload addition error handling.
- Fix DRM_BRIDGE_ATTACH_NO_CONNECTOR handling.
- Handle bad (h/v)sync_end in EDID by clipping to htotal.
- Build GPUVM as a module.
Driver Changes:
- Simple drivers don't need to cache prepared result.
- Call drm_atomic_helper_shutdown() in shutdown/unbind for a whole lot
more drm drivers.
- Assorted small fixes in amdgpu, ssd130x, bridge/it6621, accel/qaic,
nouveau, tc358768.
- Add NV12 for komeda writeback.
- Add arbitration lost event to synopsis/dw-hdmi-cec.
- Speed up s/r in nouveau by not restoring some big bo's.
- Assorted nouveau display rework in preparation for GSP-RM,
especially related to how the modeset sequence works and
the DP sequence in relation to link training.
- Update anx7816 panel.
- Support NVSYNC and NHSYNC in tegra.
- Allow multiple power domains in simple driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f1fae5eb-25b8-192a-9a53-215e1184ce81@linux.intel.com
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
For the "otm8009a" driver we fully remove the storing of the "enabled"
state and we remove the double-checking, but we still keep the storing
of the "prepared" state since the backlight code in the driver checks
it. This backlight code may not be perfectly safe since there doesn't
appear to be sufficient synchronization between the backlight driver
(which userspace can call into directly) and the code that's
unpreparing the panel. However, this lack of safety is not new and can
be addressed in a future patch.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.3.I6a4a3c81c78acf5acdc2e5b5d936e19bf57ec07a@changeid
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
For the s6e63m0 panel driver, this actually fixes a subtle/minor error
handling bug in s6e63m0_prepare(). In one error case s6e63m0_prepare()
called s6e63m0_unprepare() directly if there was an error. This call
to s6e63m0_unprepare() would have been a no-op since ctx->prepared
wasn't set yet.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.2.Iabafd062e70f6b6b554cf23eeb75f57a80f7e985@changeid
As talked about in commit d2aacaf073 ("drm/panel: Check for already
prepared/enabled in drm_panel"), we want to remove needless code from
panel drivers that was storing and double-checking the
prepared/enabled state. Even if someone was relying on the
double-check before, that double-check is now in the core and not
needed in individual drivers.
This pile of panel drivers appears to be simple to handle. Based on
code inspection they seemed to be using the prepared/enabled state
simply for double-checking that nothing else in the kernel called them
inconsistently. Now that the core drm_panel is doing the double
checking (and warning) it should be very clear that these devices
don't need their own double-check.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804140605.RFC.1.Ia54954fd2f7645c1b86597494902973f57feeb71@changeid
This panel has been implemented in commit eae7488814 ("drm/panel-simple:
Add Innolux G156HCE-L01 panel entry") with a higher clock than the typical
one mentioned on the documentation to avoid flickering on the unit
tested. Testing on a different unit shows that the panel actually works
with the intended 70.93 MHz clock and even lower frequencies so the
flickering is likely caused either by a defective unit or by other
different components such as the bridge.
Fixes: eae7488814 ("drm/panel-simple: Add Innolux G156HCE-L01 panel entry")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Vasut <marex@denx.de> # MX8MM with LT9211
Reviewed-by: Marek Vasut <marex@denx.de>
[narmstrong: fixed commit id in commit msg]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814134024.397739-1-luca.ceresoli@bootlin.com
Commit 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4
panel") added support for this panel model, but the timings it implements
are very different from what the datasheet describes. I checked both the
G121EAN01.0 datasheet from [0] and the G121EAN01.4 one from [1] and they
all have the same timings: for example the LVDS clock typical value is 74.4
MHz, not 66.7 MHz as implemented.
Replace the timings with the ones from the documentation. These timings
have been tested and the clock frequencies verified with an oscilloscope to
ensure they are correct.
Also use struct display_timing instead of struct drm_display_mode in order
to also specify the minimum and maximum values.
[0] https://embedded.avnet.com/product/g121ean01-0/
[1] https://embedded.avnet.com/product/g121ean01-4/
Fixes: 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4 panel")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804151239.835216-1-luca.ceresoli@bootlin.com
A very basic debugging rule when a device is connected for the first
time is to access a read-only register which contains known data in
order to ensure the communication protocol is properly working. This
driver lacked any read helper which is often a critical piece for
speeding-up bring-ups.
Add a read helper and use it to verify the communication with the panel
is working as soon as possible in order to inform the user early if this
is not the case.
As this panel may work with no MISO line, the check is discarded in this
case. Upon error, we do not fail probing but just warn the user, in case
the DT description would be lacking the Rx bus width (which is likely on
old descriptions) in order to avoid breaking existing devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org> # no MISO line
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-20-sre@kernel.org
This panel from Emerging Display Technologies Corporation features an
ST7789V2 LCD controller panel inside which is almost identical to what
the Sitronix panel driver supports.
In practice, the module physical size is specific, and experiments show
that the display will malfunction if any of the following situation
occurs:
* Pixel clock is above 3MHz
* Pixel clock is not inverted
I could not properly identify the reasons behind these failures, scope
captures show valid input signals.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-19-sre@kernel.org
