Add a test to check the temporary address could be added/removed
correctly when mngtempaddr is set or removed/unmanaged.
Signed-off-by: Sam Edwards <cfsworks@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Test that extacks in dumps work. The test fills up the receive buffer
to test both the inline dump (as part of sendmsg()) and delayed one
(run during recvmsg()).
Use YNL helpers to parse the messages. We need to add the test to YNL
file to make sure the right include path are used.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241119224432.1713040-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking updates from Paolo Abeni:
"The most significant set of changes is the per netns RTNL. The new
behavior is disabled by default, regression risk should be contained.
Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
default value from PTP_1588_CLOCK_KVM, as the first is intended to be
a more reliable replacement for the latter.
Core:
- Started a very large, in-progress, effort to make the RTNL lock
scope per network-namespace, thus reducing the lock contention
significantly in the containerized use-case, comprising:
- RCU-ified some relevant slices of the FIB control path
- introduce basic per netns locking helpers
- namespacified the IPv4 address hash table
- remove rtnl_register{,_module}() in favour of
rtnl_register_many()
- refactor rtnl_{new,del,set}link() moving as much validation as
possible out of RTNL lock
- convert all phonet doit() and dumpit() handlers to RCU
- convert IPv4 addresses manipulation to per-netns RTNL
- convert virtual interface creation to per-netns RTNL
the per-netns lock infrastructure is guarded by the
CONFIG_DEBUG_NET_SMALL_RTNL knob, disabled by default ad interim.
- Introduce NAPI suspension, to efficiently switching between busy
polling (NAPI processing suspended) and normal processing.
- Migrate the IPv4 routing input, output and control path from direct
ToS usage to DSCP macros. This is a work in progress to make ECN
handling consistent and reliable.
- Add drop reasons support to the IPv4 rotue input path, allowing
better introspection in case of packets drop.
- Make FIB seqnum lockless, dropping RTNL protection for read access.
- Make inet{,v6} addresses hashing less predicable.
- Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
and timestamps
Things we sprinkled into general kernel code:
- Add small file operations for debugfs, to reduce the struct ops
size.
- Refactoring and optimization for the implementation of page_frag
API, This is a preparatory work to consolidate the page_frag
implementation.
Netfilter:
- Optimize set element transactions to reduce memory consumption
- Extended netlink error reporting for attribute parser failure.
- Make legacy xtables configs user selectable, giving users the
option to configure iptables without enabling any other config.
- Address a lot of false-positive RCU issues, pointed by recent CI
improvements.
BPF:
- Put xsk sockets on a struct diet and add various cleanups. Overall,
this helps to bump performance by 12% for some workloads.
- Extend BPF selftests to increase coverage of XDP features in
combination with BPF cpumap.
- Optimize and homogenize bpf_csum_diff helper for all archs and also
add a batch of new BPF selftests for it.
- Extend netkit with an option to delegate skb->{mark,priority}
scrubbing to its BPF program.
- Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
programs.
Protocols:
- Introduces 4-tuple hash for connected udp sockets, speeding-up
significantly connected sockets lookup.
- Add a fastpath for some TCP timers that usually expires after
close, the socket lock contention.
- Add inbound and outbound xfrm state caches to speed up state
lookups.
- Avoid sending MPTCP advertisements on stale subflows, reducing
risks on loosing them.
- Make neighbours table flushing more scalable, maintaining per
device neigh lists.
Driver API:
- Introduce a unified interface to configure transmission H/W
shaping, and expose it to user-space via generic-netlink.
- Add support for per-NAPI config via netlink. This makes napi
configuration persistent across queues removal and re-creation.
Requires driver updates, currently supported drivers are:
nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.
- Add ethtool support for writing SFP / PHY firmware blocks.
- Track RSS context allocation from ethtool core.
- Implement support for mirroring to DSA CPU port, via TC mirror
offload.
- Consolidate FDB updates notification, to avoid duplicates on
device-specific entries.
- Expose DPLL clock quality level to the user-space.
- Support master-slave PHY config via device tree.
Tests and tooling:
- forwarding: introduce deferred commands, to simplify the cleanup
phase
Drivers:
- Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
IRQs and queues to NAPI IDs, allowing busy polling and better
introspection.
- Ethernet high-speed NICs:
- nVidia/Mellanox:
- mlx5:
- a large refactor to implement support for cross E-Switch
scheduling
- refactor H/W conter management to let it scale better
- H/W GRO cleanups
- Intel (100G, ice)::
- add support for ethtool reset
- implement support for per TX queue H/W shaping
- AMD/Solarflare:
- implement per device queue stats support
- Broadcom (bnxt):
- improve wildcard l4proto on IPv4/IPv6 ntuple rules
- Marvell Octeon:
- Add representor support for each Resource Virtualization Unit
(RVU) device.
- Hisilicon:
- add support for the BMC Gigabit Ethernet
- IBM (EMAC):
- driver cleanup and modernization
- Cisco (VIC):
- raise the queues number limit to 256
- Ethernet virtual:
- Google vNIC:
- implement page pool support
- macsec:
- inherit lower device's features and TSO limits when
offloading
- virtio_net:
- enable premapped mode by default
- support for XDP socket(AF_XDP) zerocopy TX
- wireguard:
- set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
packets.
- Ethernet NICs embedded and virtual:
- Broadcom ASP:
- enable software timestamping
- Freescale:
- add enetc4 PF driver
- MediaTek: Airoha SoC:
- implement BQL support
- RealTek r8169:
- enable TSO by default on r8168/r8125
- implement extended ethtool stats
- Renesas AVB:
- enable TX checksum offload
- Synopsys (stmmac):
- support header splitting for vlan tagged packets
- move common code for DWMAC4 and DWXGMAC into a separate FPE
module.
- add dwmac driver support for T-HEAD TH1520 SoC
- Synopsys (xpcs):
- driver refactor and cleanup
- TI:
- icssg_prueth: add VLAN offload support
- Xilinx emaclite:
- add clock support
- Ethernet switches:
- Microchip:
- implement support for the lan969x Ethernet switch family
- add LAN9646 switch support to KSZ DSA driver
- Ethernet PHYs:
- Marvel: 88q2x: enable auto negotiation
- Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2
- PTP:
- Add support for the Amazon virtual clock device
- Add PtP driver for s390 clocks
- WiFi:
- mac80211
- EHT 1024 aggregation size for transmissions
- new operation to indicate that a new interface is to be added
- support radio separation of multi-band devices
- move wireless extension spy implementation to libiw
- Broadcom:
- brcmfmac: optional LPO clock support
- Microchip:
- add support for Atmel WILC3000
- Qualcomm (ath12k):
- firmware coredump collection support
- add debugfs support for a multitude of statistics
- Qualcomm (ath5k):
- Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
- Realtek:
- rtw88: 8821au and 8812au USB adapters support
- rtw89: add thermal protection
- rtw89: fine tune BT-coexsitence to improve user experience
- rtw89: firmware secure boot for WiFi 6 chip
- Bluetooth
- add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
0x13d3:0x3623
- add Realtek RTL8852BE support for id Foxconn 0xe123
- add MediaTek MT7920 support for wireless module ids
- btintel_pcie: add handshake between driver and firmware
- btintel_pcie: add recovery mechanism
- btnxpuart: add GPIO support to power save feature"
* tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1475 commits)
mm: page_frag: fix a compile error when kernel is not compiled
Documentation: tipc: fix formatting issue in tipc.rst
selftests: nic_performance: Add selftest for performance of NIC driver
selftests: nic_link_layer: Add selftest case for speed and duplex states
selftests: nic_link_layer: Add link layer selftest for NIC driver
bnxt_en: Add FW trace coredump segments to the coredump
bnxt_en: Add a new ethtool -W dump flag
bnxt_en: Add 2 parameters to bnxt_fill_coredump_seg_hdr()
bnxt_en: Add functions to copy host context memory
bnxt_en: Do not free FW log context memory
bnxt_en: Manage the FW trace context memory
bnxt_en: Allocate backing store memory for FW trace logs
bnxt_en: Add a 'force' parameter to bnxt_free_ctx_mem()
bnxt_en: Refactor bnxt_free_ctx_mem()
bnxt_en: Add mem_valid bit to struct bnxt_ctx_mem_type
bnxt_en: Update firmware interface spec to 1.10.3.85
selftests/bpf: Add some tests with sockmap SK_PASS
bpf: fix recursive lock when verdict program return SK_PASS
wireguard: device: support big tcp GSO
wireguard: selftests: load nf_conntrack if not present
...
Pull bpf updates from Alexei Starovoitov:
- Add BPF uprobe session support (Jiri Olsa)
- Optimize uprobe performance (Andrii Nakryiko)
- Add bpf_fastcall support to helpers and kfuncs (Eduard Zingerman)
- Avoid calling free_htab_elem() under hash map bucket lock (Hou Tao)
- Prevent tailcall infinite loop caused by freplace (Leon Hwang)
- Mark raw_tracepoint arguments as nullable (Kumar Kartikeya Dwivedi)
- Introduce uptr support in the task local storage map (Martin KaFai
Lau)
- Stringify errno log messages in libbpf (Mykyta Yatsenko)
- Add kmem_cache BPF iterator for perf's lock profiling (Namhyung Kim)
- Support BPF objects of either endianness in libbpf (Tony Ambardar)
- Add ksym to struct_ops trampoline to fix stack trace (Xu Kuohai)
- Introduce private stack for eligible BPF programs (Yonghong Song)
- Migrate samples/bpf tests to selftests/bpf test_progs (Daniel T. Lee)
- Migrate test_sock to selftests/bpf test_progs (Jordan Rife)
* tag 'bpf-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (152 commits)
libbpf: Change hash_combine parameters from long to unsigned long
selftests/bpf: Fix build error with llvm 19
libbpf: Fix memory leak in bpf_program__attach_uprobe_multi
bpf: use common instruction history across all states
bpf: Add necessary migrate_disable to range_tree.
bpf: Do not alloc arena on unsupported arches
selftests/bpf: Set test path for token/obj_priv_implicit_token_envvar
selftests/bpf: Add a test for arena range tree algorithm
bpf: Introduce range_tree data structure and use it in bpf arena
samples/bpf: Remove unused variable in xdp2skb_meta_kern.c
samples/bpf: Remove unused variables in tc_l2_redirect_kern.c
bpftool: Cast variable `var` to long long
bpf, x86: Propagate tailcall info only for subprogs
bpf: Add kernel symbol for struct_ops trampoline
bpf: Use function pointers count as struct_ops links count
bpf: Remove unused member rcu from bpf_struct_ops_map
selftests/bpf: Add struct_ops prog private stack tests
bpf: Support private stack for struct_ops progs
selftests/bpf: Add tracing prog private stack tests
bpf, x86: Support private stack in jit
...
Pull HID updates from Jiri Kosina:
- improvement in the way hid-bpf coexists with specific drivers (others
than hid-generic) that are already bound to devices (Benjamin
Tissoires)
- removal of three way-too-aggressive BUG_ON()s from HID drivers (He
Lugang)
- assorted cleanups and small code fixes to HID core (Dmitry Torokhov,
Yan Zhen, Nathan Chancellor, Andy Shevchenko)
- support for Corsair Void headset family (Stuart Hayhurst)
- Support for Goodix GT7986U SPI (Charles Wang)
- initial vendor-specific driver for Kysona, currently adding support
for Kysona M600 (Lode Willems)
- other assorted code cleanups and small bugfixes all over the place
* tag 'hid-for-linus-2024111801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (40 commits)
HID: multitouch: make mt_set_mode() less cryptic
HID: hid-goodix-spi: Add OF supports
dt-bindings: input: Goodix GT7986U SPI HID Touchscreen
HID: hyperv: streamline driver probe to avoid devres issues
HID: magicmouse: Apple Magic Trackpad 2 USB-C driver support
HID: rmi: Add select RMI4_F3A in Kconfig
HID: wacom: Interpret tilt data from Intuos Pro BT as signed values
HID: steelseries: Add capacity_level mapping
HID: steelseries: Fix battery requests stopping after some time
HID: hid-goodix: Fix HID get/set feature operation overwritten problem
HID: hid-goodix: Return 0 when receiving an empty HID feature package
HID: bpf: drop use of Logical|Physical|UsageRange
HID: bpf: Fix Rapoo M50 Plus Silent side buttons
HID: bpf: Fix NKRO on Mistel MD770
HID: replace BUG_ON() with WARN_ON()
HID: wacom: Set eraser status when either 'Eraser' or 'Invert' usage is set
HID: Kysona: add basic online status
HID: Kysona: check battery status every 5s using a workqueue
HID: Kysona: Add basic battery reporting for Kysona M600
HID: Add IDs for Kysona
...
Pull kselftest update from Shuah Khan:
"timer test:
- remove duplicate defines
- fixes to improve error reporting
rtc test:
- check rtc alarm status in alarm test
resctrl test:
- add array overrun checks during iMC config parsing code and when
reading strings
- fixes and reorganizing code"
* tag 'linux_kselftest-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (23 commits)
selftests/resctrl: Replace magic constants used as array size
selftests/resctrl: Keep results from first test run
selftests/resctrl: Do not compare performance counters and resctrl at low bandwidth
selftests/resctrl: Use cache size to determine "fill_buf" buffer size
selftests/resctrl: Ensure measurements skip initialization of default benchmark
selftests/resctrl: Make benchmark parameter passing robust
selftests/resctrl: Remove unused measurement code
selftests/resctrl: Only support measured read operation
selftests/resctrl: Remove "once" parameter required to be false
selftests/resctrl: Make wraparound handling obvious
selftests/resctrl: Protect against array overflow when reading strings
selftests/resctrl: Protect against array overrun during iMC config parsing
selftests/resctrl: Fix memory overflow due to unhandled wraparound
selftests/resctrl: Print accurate buffer size as part of MBM results
selftests/resctrl: Make functions only used in same file static
selftests: Add a test mangling with uc_sigmask
selftests: Rename sigaltstack to generic signal
selftest: rtc: Add to check rtc alarm status for alarm related test
selftests:timers: remove local CLOCKID defines
selftests: timers: Remove unneeded semicolon
...
Pull ftrace updates from Steven Rostedt:
- Restructure the function graph shadow stack to prepare it for use
with kretprobes
With the goal of merging the shadow stack logic of function graph and
kretprobes, some more restructuring of the function shadow stack is
required.
Move out function graph specific fields from the fgraph
infrastructure and store it on the new stack variables that can pass
data from the entry callback to the exit callback.
Hopefully, with this change, the merge of kretprobes to use fgraph
shadow stacks will be ready by the next merge window.
- Make shadow stack 4k instead of using PAGE_SIZE.
Some architectures have very large PAGE_SIZE values which make its
use for shadow stacks waste a lot of memory.
- Give shadow stacks its own kmem cache.
When function graph is started, every task on the system gets a
shadow stack. In the future, shadow stacks may not be 4K in size.
Have it have its own kmem cache so that whatever size it becomes will
still be efficient in allocations.
- Initialize profiler graph ops as it will be needed for new updates to
fgraph
- Convert to use guard(mutex) for several ftrace and fgraph functions
- Add more comments and documentation
- Show function return address in function graph tracer
Add an option to show the caller of a function at each entry of the
function graph tracer, similar to what the function tracer does.
- Abstract out ftrace_regs from being used directly like pt_regs
ftrace_regs was created to store a partial pt_regs. It holds only the
registers and stack information to get to the function arguments and
return values. On several archs, it is simply a wrapper around
pt_regs. But some users would access ftrace_regs directly to get the
pt_regs which will not work on all archs. Make ftrace_regs an
abstract structure that requires all access to its fields be through
accessor functions.
- Show how long it takes to do function code modifications
When code modification for function hooks happen, it always had the
time recorded in how long it took to do the conversion. But this
value was never exported. Recently the code was touched due to new
ROX modification handling that caused a large slow down in doing the
modifications and had a significant impact on boot times.
Expose the timings in the dyn_ftrace_total_info file. This file was
created a while ago to show information about memory usage and such
to implement dynamic function tracing. It's also an appropriate file
to store the timings of this modification as well. This will make it
easier to see the impact of changes to code modification on boot up
timings.
- Other clean ups and small fixes
* tag 'ftrace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (22 commits)
ftrace: Show timings of how long nop patching took
ftrace: Use guard to take ftrace_lock in ftrace_graph_set_hash()
ftrace: Use guard to take the ftrace_lock in release_probe()
ftrace: Use guard to lock ftrace_lock in cache_mod()
ftrace: Use guard for match_records()
fgraph: Use guard(mutex)(&ftrace_lock) for unregister_ftrace_graph()
fgraph: Give ret_stack its own kmem cache
fgraph: Separate size of ret_stack from PAGE_SIZE
ftrace: Rename ftrace_regs_return_value to ftrace_regs_get_return_value
selftests/ftrace: Fix check of return value in fgraph-retval.tc test
ftrace: Use arch_ftrace_regs() for ftrace_regs_*() macros
ftrace: Consolidate ftrace_regs accessor functions for archs using pt_regs
ftrace: Make ftrace_regs abstract from direct use
fgragh: No need to invoke the function call_filter_check_discard()
fgraph: Simplify return address printing in function graph tracer
function_graph: Remove unnecessary initialization in ftrace_graph_ret_addr()
function_graph: Support recording and printing the function return address
ftrace: Have calltime be saved in the fgraph storage
ftrace: Use a running sleeptime instead of saving on shadow stack
fgraph: Use fgraph data to store subtime for profiler
...
Pull cgroup updates from Tejun Heo:
- cpu.stat now also shows niced CPU time
- Freezer and cpuset optimizations
- Other misc changes
* tag 'cgroup-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Disable cpuset_cpumask_can_shrink() test if not load balancing
cgroup/cpuset: Further optimize code if CONFIG_CPUSETS_V1 not set
cgroup/cpuset: Enforce at most one rebuild_sched_domains_locked() call per operation
cgroup/cpuset: Revert "Allow suppression of sched domain rebuild in update_cpumasks_hier()"
MAINTAINERS: remove Zefan Li
cgroup/freezer: Add cgroup CGRP_FROZEN flag update helper
cgroup/freezer: Reduce redundant traversal for cgroup_freeze
cgroup/bpf: only cgroup v2 can be attached by bpf programs
Revert "cgroup: Fix memory leak caused by missing cgroup_bpf_offline"
selftests/cgroup: Fix compile error in test_cpu.c
cgroup/rstat: Selftests for niced CPU statistics
cgroup/rstat: Tracking cgroup-level niced CPU time
cgroup/cpuset: Fix spelling errors in file kernel/cgroup/cpuset.c
Pull livepatching update from Petr Mladek:
- A new selftest for livepatching of a kprobed function
* tag 'livepatching-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
selftests: livepatch: test livepatching a kprobed function
selftests: livepatch: save and restore kprobe state
selftests: livepatch: rename KLP_SYSFS_DIR to SYSFS_KLP_DIR
Pull timer updates from Thomas Gleixner:
"A rather large update for timekeeping and timers:
- The final step to get rid of auto-rearming posix-timers
posix-timers are currently auto-rearmed by the kernel when the
signal of the timer is ignored so that the timer signal can be
delivered once the corresponding signal is unignored.
This requires to throttle the timer to prevent a DoS by small
intervals and keeps the system pointlessly out of low power states
for no value. This is a long standing non-trivial problem due to
the lock order of posix-timer lock and the sighand lock along with
life time issues as the timer and the sigqueue have different life
time rules.
Cure this by:
- Embedding the sigqueue into the timer struct to have the same
life time rules. Aside of that this also avoids the lookup of
the timer in the signal delivery and rearm path as it's just a
always valid container_of() now.
- Queuing ignored timer signals onto a seperate ignored list.
- Moving queued timer signals onto the ignored list when the
signal is switched to SIG_IGN before it could be delivered.
- Walking the ignored list when SIG_IGN is lifted and requeue the
signals to the actual signal lists. This allows the signal
delivery code to rearm the timer.
This also required to consolidate the signal delivery rules so they
are consistent across all situations. With that all self test
scenarios finally succeed.
- Core infrastructure for VFS multigrain timestamping
This is required to allow the kernel to use coarse grained time
stamps by default and switch to fine grained time stamps when inode
attributes are actively observed via getattr().
These changes have been provided to the VFS tree as well, so that
the VFS specific infrastructure could be built on top.
- Cleanup and consolidation of the sleep() infrastructure
- Move all sleep and timeout functions into one file
- Rework udelay() and ndelay() into proper documented inline
functions and replace the hardcoded magic numbers by proper
defines.
- Rework the fsleep() implementation to take the reality of the
timer wheel granularity on different HZ values into account.
Right now the boundaries are hard coded time ranges which fail
to provide the requested accuracy on different HZ settings.
- Update documentation for all sleep/timeout related functions
and fix up stale documentation links all over the place
- Fixup a few usage sites
- Rework of timekeeping and adjtimex(2) to prepare for multiple PTP
clocks
A system can have multiple PTP clocks which are participating in
seperate and independent PTP clock domains. So far the kernel only
considers the PTP clock which is based on CLOCK TAI relevant as
that's the clock which drives the timekeeping adjustments via the
various user space daemons through adjtimex(2).
The non TAI based clock domains are accessible via the file
descriptor based posix clocks, but their usability is very limited.
They can't be accessed fast as they always go all the way out to
the hardware and they cannot be utilized in the kernel itself.
As Time Sensitive Networking (TSN) gains traction it is required to
provide fast user and kernel space access to these clocks.
The approach taken is to utilize the timekeeping and adjtimex(2)
infrastructure to provide this access in a similar way how the
kernel provides access to clock MONOTONIC, REALTIME etc.
Instead of creating a duplicated infrastructure this rework
converts timekeeping and adjtimex(2) into generic functionality
which operates on pointers to data structures instead of using
static variables.
This allows to provide time accessors and adjtimex(2) functionality
for the independent PTP clocks in a subsequent step.
- Consolidate hrtimer initialization
hrtimers are set up by initializing the data structure and then
seperately setting the callback function for historical reasons.
That's an extra unnecessary step and makes Rust support less
straight forward than it should be.
Provide a new set of hrtimer_setup*() functions and convert the
core code and a few usage sites of the less frequently used
interfaces over.
The bulk of the htimer_init() to hrtimer_setup() conversion is
already prepared and scheduled for the next merge window.
- Drivers:
- Ensure that the global timekeeping clocksource is utilizing the
cluster 0 timer on MIPS multi-cluster systems.
Otherwise CPUs on different clusters use their cluster specific
clocksource which is not guaranteed to be synchronized with
other clusters.
- Mostly boring cleanups, fixes, improvements and code movement"
* tag 'timers-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (140 commits)
posix-timers: Fix spurious warning on double enqueue versus do_exit()
clocksource/drivers/arm_arch_timer: Use of_property_present() for non-boolean properties
clocksource/drivers/gpx: Remove redundant casts
clocksource/drivers/timer-ti-dm: Fix child node refcount handling
dt-bindings: timer: actions,owl-timer: convert to YAML
clocksource/drivers/ralink: Add Ralink System Tick Counter driver
clocksource/drivers/mips-gic-timer: Always use cluster 0 counter as clocksource
clocksource/drivers/timer-ti-dm: Don't fail probe if int not found
clocksource/drivers:sp804: Make user selectable
clocksource/drivers/dw_apb: Remove unused dw_apb_clockevent functions
hrtimers: Delete hrtimer_init_on_stack()
alarmtimer: Switch to use hrtimer_setup() and hrtimer_setup_on_stack()
io_uring: Switch to use hrtimer_setup_on_stack()
sched/idle: Switch to use hrtimer_setup_on_stack()
hrtimers: Delete hrtimer_init_sleeper_on_stack()
wait: Switch to use hrtimer_setup_sleeper_on_stack()
timers: Switch to use hrtimer_setup_sleeper_on_stack()
net: pktgen: Switch to use hrtimer_setup_sleeper_on_stack()
futex: Switch to use hrtimer_setup_sleeper_on_stack()
fs/aio: Switch to use hrtimer_setup_sleeper_on_stack()
...
Pull performance events updates from Ingo Molnar:
"Uprobes:
- Add BPF session support (Jiri Olsa)
- Switch to RCU Tasks Trace flavor for better performance (Andrii
Nakryiko)
- Massively increase uretprobe SMP scalability by SRCU-protecting
the uretprobe lifetime (Andrii Nakryiko)
- Kill xol_area->slot_count (Oleg Nesterov)
Core facilities:
- Implement targeted high-frequency profiling by adding the ability
for an event to "pause" or "resume" AUX area tracing (Adrian
Hunter)
VM profiling/sampling:
- Correct perf sampling with guest VMs (Colton Lewis)
New hardware support:
- x86/intel: Add PMU support for Intel ArrowLake-H CPUs (Dapeng Mi)
Misc fixes and enhancements:
- x86/intel/pt: Fix buffer full but size is 0 case (Adrian Hunter)
- x86/amd: Warn only on new bits set (Breno Leitao)
- x86/amd/uncore: Avoid a false positive warning about snprintf
truncation in amd_uncore_umc_ctx_init (Jean Delvare)
- uprobes: Re-order struct uprobe_task to save some space
(Christophe JAILLET)
- x86/rapl: Move the pmu allocation out of CPU hotplug (Kan Liang)
- x86/rapl: Clean up cpumask and hotplug (Kan Liang)
- uprobes: Deuglify xol_get_insn_slot/xol_free_insn_slot paths (Oleg
Nesterov)"
* tag 'perf-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
perf/core: Correct perf sampling with guest VMs
perf/x86: Refactor misc flag assignments
perf/powerpc: Use perf_arch_instruction_pointer()
perf/core: Hoist perf_instruction_pointer() and perf_misc_flags()
perf/arm: Drop unused functions
uprobes: Re-order struct uprobe_task to save some space
perf/x86/amd/uncore: Avoid a false positive warning about snprintf truncation in amd_uncore_umc_ctx_init
perf/x86/intel: Do not enable large PEBS for events with aux actions or aux sampling
perf/x86/intel/pt: Add support for pause / resume
perf/core: Add aux_pause, aux_resume, aux_start_paused
perf/x86/intel/pt: Fix buffer full but size is 0 case
uprobes: SRCU-protect uretprobe lifetime (with timeout)
uprobes: allow put_uprobe() from non-sleepable softirq context
perf/x86/rapl: Clean up cpumask and hotplug
perf/x86/rapl: Move the pmu allocation out of CPU hotplug
uprobe: Add support for session consumer
uprobe: Add data pointer to consumer handlers
perf/x86/amd: Warn only on new bits set
uprobes: fold xol_take_insn_slot() into xol_get_insn_slot()
uprobes: kill xol_area->slot_count
...
Pull RCU updates from Frederic Weisbecker:
"SRCU:
- Introduction of the new SRCU-lite flavour with a new pair of
srcu_read_[un]lock_lite() APIs. In practice the read side using
this flavour becomes lighter by removing a full memory barrier on
LOCK and a full memory barrier on UNLOCK. This comes at the expense
of a higher latency write side with two (in the best case of a
snaphot of unused read-sides) or more RCU grace periods on the
update side which now assumes by itself the whole full ordering
guarantee against the LOCK/UNLOCK counters on both indexes, along
with the accesses performed inside.
Uretprobes is a known potential user.
Note this doesn't replace the default normal flavour of SRCU which
still behaves the same as usual.
- Add testing of SRCU-lite through rcutorture and rcuscale
- Various cleanups on the way.
Fixes:
- Allow short-circuiting RCU-TASKS-RUDE grace periods on
architectures that have sane noinstr boundaries forbidding tracing
on low-level idle and kernel entry code. RCU-TASKS is enough on
such configurations because it involves an RCU grace period that
waits for all idle tasks to either schedule out voluntarily or
enter into RCU unwatched noinstr code.
- Allow and test start_poll_synchronize_rcu() with IRQs disabled.
- Mention rcuog kthreads in relevant documentation and Kconfig help
- Various fixes and consolidations
rcutorture:
- Add --no-affinity on tools to leave the affinity setting of guests
up to the user.
- Add guest_os_delay parameter to rcuscale for better warm-up
control.
- Fix and improve some rcuscale error handling.
- Various cleanups and fixes
stall:
- Remove dead code
- Stop dumping tasks if a stalled grace period eventually ended
midway as that only produces confusing output.
- Optimize detection of stalling CPUs and avoid useless node locking
otherwise.
NOCB:
- Fix rcu_barrier() hang due to a race against callbacks
deoffloading. This is not yet used, except by rcutorture, and waits
for its promised cpusets interface.
- Remove leftover function declaration"
* tag 'rcu.release.v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rcu/linux: (42 commits)
rcuscale: Remove redundant WARN_ON_ONCE() splat
rcuscale: Do a proper cleanup if kfree_scale_init() fails
srcu: Unconditionally record srcu_read_lock_lite() in ->srcu_reader_flavor
srcu: Check for srcu_read_lock_lite() across all CPUs
srcu: Remove smp_mb() from srcu_read_unlock_lite()
rcutorture: Avoid printing cpu=-1 for no-fault RCU boost failure
rcuscale: Add guest_os_delay module parameter
refscale: Correct affinity check
torture: Add --no-affinity parameter to kvm.sh
rcu/nocb: Fix missed RCU barrier on deoffloading
rcu/kvfree: Fix data-race in __mod_timer / kvfree_call_rcu
rcu/srcutiny: don't return before reenabling preemption
rcu-tasks: Remove open-coded one-byte cmpxchg() emulation
doc: Remove kernel-parameters.txt entry for rcutorture.read_exit
rcutorture: Test start-poll primitives with interrupts disabled
rcu: Permit start_poll_synchronize_rcu*() with interrupts disabled
rcu: Allow short-circuiting of synchronize_rcu_tasks_rude()
doc: Add rcuog kthreads to kernel-per-CPU-kthreads.rst
rcu: Add rcuog kthreads to RCU_NOCB_CPU help text
rcu: Use the BITS_PER_LONG macro
...
Pull nolibc updates from Paul McKenney:
- Fix potential error due to missing #include on s390
- Compatibility with -Wmissing-fallthrough
- Run qemu with more memory during tests
* tag 'nolibc.2024.11.01a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
selftests/nolibc: start qemu with 1 GiB of memory
tools/nolibc: compiler: add macro __nolibc_fallthrough
tools/nolibc: s390: include std.h
Add selftest case to check the send and receive throughput.
Supported link modes between local NIC driver and partner
are varied. Then send and receive throughput is captured
and verified. Test uses iperf3 tool.
Add iperf3 server/client function in GenerateTraffic class.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add selftest case for testing the speed and duplex state of
local NIC driver and the partner based on the supported
link modes obtained from the ethtool. Speed and duplex states
are varied and verified using ethtool.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add selftest file for the link layer tests of a NIC driver.
Test for auto-negotiation is added.
Add LinkConfig class for changing link layer configs.
Selftest makes use of ksft modules and ethtool.
Include selftest file in the Makefile.
Signed-off-by: Mohan Prasad J <mohan.prasad@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bpf_offload caught a spurious warning in TC recently, but the error
message did not provide enough information to know what the problem
is:
FAIL: Found 'netdevsim' in command output, leaky extack?
Add the extack to the output:
FAIL: Unexpected command output, leaky extack? ('netdevsim', 'Warning: Filter with specified priority/protocol not found.')
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull arm64 updates from Catalin Marinas:
- Support for running Linux in a protected VM under the Arm
Confidential Compute Architecture (CCA)
- Guarded Control Stack user-space support. Current patches follow the
x86 ABI of implicitly creating a shadow stack on clone(). Subsequent
patches (already on the list) will add support for clone3() allowing
finer-grained control of the shadow stack size and placement from
libc
- AT_HWCAP3 support (not running out of HWCAP2 bits yet but we are
getting close with the upcoming dpISA support)
- Other arch features:
- In-kernel use of the memcpy instructions, FEAT_MOPS (previously
only exposed to user; uaccess support not merged yet)
- MTE: hugetlbfs support and the corresponding kselftests
- Optimise CRC32 using the PMULL instructions
- Support for FEAT_HAFT enabling ARCH_HAS_NONLEAF_PMD_YOUNG
- Optimise the kernel TLB flushing to use the range operations
- POE/pkey (permission overlays): further cleanups after bringing
the signal handler in line with the x86 behaviour for 6.12
- arm64 perf updates:
- Support for the NXP i.MX91 PMU in the existing IMX driver
- Support for Ampere SoCs in the Designware PCIe PMU driver
- Support for Marvell's 'PEM' PCIe PMU present in the 'Odyssey' SoC
- Support for Samsung's 'Mongoose' CPU PMU
- Support for PMUv3.9 finer-grained userspace counter access
control
- Switch back to platform_driver::remove() now that it returns
'void'
- Add some missing events for the CXL PMU driver
- Miscellaneous arm64 fixes/cleanups:
- Page table accessors cleanup: type updates, drop unused macros,
reorganise arch_make_huge_pte() and clean up pte_mkcont(), sanity
check addresses before runtime P4D/PUD folding
- Command line override for ID_AA64MMFR0_EL1.ECV (advertising the
FEAT_ECV for the generic timers) allowing Linux to boot with
firmware deployments that don't set SCTLR_EL3.ECVEn
- ACPI/arm64: tighten the check for the array of platform timer
structures and adjust the error handling procedure in
gtdt_parse_timer_block()
- Optimise the cache flush for the uprobes xol slot (skip if no
change) and other uprobes/kprobes cleanups
- Fix the context switching of tpidrro_el0 when kpti is enabled
- Dynamic shadow call stack fixes
- Sysreg updates
- Various arm64 kselftest improvements
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (168 commits)
arm64: tls: Fix context-switching of tpidrro_el0 when kpti is enabled
kselftest/arm64: Try harder to generate different keys during PAC tests
kselftest/arm64: Don't leak pipe fds in pac.exec_sign_all()
arm64/ptrace: Clarify documentation of VL configuration via ptrace
kselftest/arm64: Corrupt P0 in the irritator when testing SSVE
acpi/arm64: remove unnecessary cast
arm64/mm: Change protval as 'pteval_t' in map_range()
kselftest/arm64: Fix missing printf() argument in gcs/gcs-stress.c
kselftest/arm64: Add FPMR coverage to fp-ptrace
kselftest/arm64: Expand the set of ZA writes fp-ptrace does
kselftets/arm64: Use flag bits for features in fp-ptrace assembler code
kselftest/arm64: Enable build of PAC tests with LLVM=1
kselftest/arm64: Check that SVCR is 0 in signal handlers
selftests/mm: Fix unused function warning for aarch64_write_signal_pkey()
kselftest/arm64: Fix printf() compiler warnings in the arm64 syscall-abi.c tests
kselftest/arm64: Fix printf() warning in the arm64 MTE prctl() test
kselftest/arm64: Fix printf() compiler warnings in the arm64 fp tests
kselftest/arm64: Fix build with stricter assemblers
arm64/scs: Drop unused prototype __pi_scs_patch_vmlinux()
arm64/scs: Deal with 64-bit relative offsets in FDE frames
...
Pull pidfs update from Christian Brauner:
"This adds a new ioctl to retrieve information about a pidfd.
A common pattern when using pidfds is having to get information about
the process, which currently requires /proc being mounted, resolving
the fd to a pid, and then do manual string parsing of /proc/N/status
and friends. This needs to be reimplemented over and over in all
userspace projects (e.g.: it has been reimplemented in systemd, dbus,
dbus-daemon, polkit so far), and requires additional care in checking
that the fd is still valid after having parsed the data, to avoid
races.
Having a programmatic API that can be used directly removes all these
requirements, including having /proc mounted.
As discussed at LPC24, add an ioctl with an extensible struct so that
more parameters can be added later if needed. Start with returning
pid/tgid/ppid and some creds unconditionally, and cgroupid optionally"
* tag 'vfs-6.13.pidfs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
pidfd: add ioctl to retrieve pid info
Pull overlayfs updates from Christian Brauner:
"Make overlayfs support specifying layers through file descriptors.
Currently overlayfs only allows specifying layers through path names.
This is inconvenient for users that want to assemble an overlayfs
mount purely based on file descriptors:
This enables user to specify both:
fsconfig(fd_overlay, FSCONFIG_SET_FD, "upperdir+", NULL, fd_upper);
fsconfig(fd_overlay, FSCONFIG_SET_FD, "workdir+", NULL, fd_work);
fsconfig(fd_overlay, FSCONFIG_SET_FD, "lowerdir+", NULL, fd_lower1);
fsconfig(fd_overlay, FSCONFIG_SET_FD, "lowerdir+", NULL, fd_lower2);
in addition to:
fsconfig(fd_overlay, FSCONFIG_SET_STRING, "upperdir+", "/upper", 0);
fsconfig(fd_overlay, FSCONFIG_SET_STRING, "workdir+", "/work", 0);
fsconfig(fd_overlay, FSCONFIG_SET_STRING, "lowerdir+", "/lower1", 0);
fsconfig(fd_overlay, FSCONFIG_SET_STRING, "lowerdir+", "/lower2", 0);
There's also a large set of new overlayfs selftests to test new
features and some older properties"
* tag 'vfs-6.13.ovl' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
selftests: add test for specifying 500 lower layers
selftests: add overlayfs fd mounting selftests
selftests: use shared header
Documentation,ovl: document new file descriptor based layers
ovl: specify layers via file descriptors
fs: add helper to use mount option as path or fd
Pull vfs file updates from Christian Brauner:
"This contains changes the changes for files for this cycle:
- Introduce a new reference counting mechanism for files.
As atomic_inc_not_zero() is implemented with a try_cmpxchg() loop
it has O(N^2) behaviour under contention with N concurrent
operations and it is in a hot path in __fget_files_rcu().
The rcuref infrastructures remedies this problem by using an
unconditional increment relying on safe- and dead zones to make
this work and requiring rcu protection for the data structure in
question. This not just scales better it also introduces overflow
protection.
However, in contrast to generic rcuref, files require a memory
barrier and thus cannot rely on *_relaxed() atomic operations and
also require to be built on atomic_long_t as having massive amounts
of reference isn't unheard of even if it is just an attack.
This adds a file specific variant instead of making this a generic
library.
This has been tested by various people and it gives consistent
improvement up to 3-5% on workloads with loads of threads.
- Add a fastpath for find_next_zero_bit(). Skip 2-levels searching
via find_next_zero_bit() when there is a free slot in the word that
contains the next fd. This improves pts/blogbench-1.1.0 read by 8%
and write by 4% on Intel ICX 160.
- Conditionally clear full_fds_bits since it's very likely that a bit
in full_fds_bits has been cleared during __clear_open_fds(). This
improves pts/blogbench-1.1.0 read up to 13%, and write up to 5% on
Intel ICX 160.
- Get rid of all lookup_*_fdget_rcu() variants. They were used to
lookup files without taking a reference count. That became invalid
once files were switched to SLAB_TYPESAFE_BY_RCU and now we're
always taking a reference count. Switch to an already existing
helper and remove the legacy variants.
- Remove pointless includes of <linux/fdtable.h>.
- Avoid cmpxchg() in close_files() as nobody else has a reference to
the files_struct at that point.
- Move close_range() into fs/file.c and fold __close_range() into it.
- Cleanup calling conventions of alloc_fdtable() and expand_files().
- Merge __{set,clear}_close_on_exec() into one.
- Make __set_open_fd() set cloexec as well instead of doing it in two
separate steps"
* tag 'vfs-6.13.file' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
selftests: add file SLAB_TYPESAFE_BY_RCU recycling stressor
fs: port files to file_ref
fs: add file_ref
expand_files(): simplify calling conventions
make __set_open_fd() set cloexec state as well
fs: protect backing files with rcu
file.c: merge __{set,clear}_close_on_exec()
alloc_fdtable(): change calling conventions.
fs/file.c: add fast path in find_next_fd()
fs/file.c: conditionally clear full_fds
fs/file.c: remove sanity_check and add likely/unlikely in alloc_fd()
move close_range(2) into fs/file.c, fold __close_range() into it
close_files(): don't bother with xchg()
remove pointless includes of <linux/fdtable.h>
get rid of ...lookup...fdget_rcu() family
llvm 19 fails to compile arena self test:
CLNG-BPF [test_progs] verifier_arena_large.bpf.o
progs/verifier_arena_large.c:90:24: error: unsupported signed division, please convert to unsigned div/mod.
90 | pg_idx = (pg - base) / PAGE_SIZE;
Though llvm <= 18 and llvm >= 20 don't have this issue,
fix the test to avoid the build error.
Reported-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Check that only one notification is produced for various FDB edit
operations.
Regarding the ip_link_add() and ip_link_master() helpers. This pattern of
action plus corresponding defer is bound to come up often, and a dedicated
vocabulary to capture it will be handy. tunnel_create() and vlan_create()
from forwarding/lib.sh are somewhat opaque and perhaps too kitchen-sinky,
so I tried to go in the opposite direction with these ones, and wrapped
only the bare minimum to schedule a corresponding cleanup.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/910c5880ae6d3b558d6889cbdba2be690c2615c6.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For logging to be useful, something has to set RET and retmsg by calling
ret_set_ksft_status(). There is a suite of functions to that end in
forwarding/lib: check_err, check_fail et.al. Move them to net/lib.sh so
that every net test can use them.
Existing lib.sh users might be using these same names for their functions.
However lib.sh is always sourced near the top of the file (checked), and
whatever new definitions will simply override the ones provided by lib.sh.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/f488a00dc85b8e0c1f3c71476b32b21b5189a847.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It would be good to use the same mechanism for scheduling and dispatching
general net tests as the many forwarding tests already use. To that end,
move the logging helpers to net/lib.sh so that every net test can use them.
Existing lib.sh users might be using the name themselves. However lib.sh is
always sourced near the top of the file (checked), and whatever new
definition will simply override the one provided by lib.sh.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/a6fc083486493425b2c61185c327845b6ce3233a.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Many net selftests invent their own logging helpers. These really should be
in a library sourced by these tests. Currently forwarding/lib.sh has a
suite of perfectly fine logging helpers, but sourcing a forwarding/ library
from a higher-level directory smells of layering violation. In this patch,
move the logging helpers to net/lib.sh so that every net test can use them.
Together with the logging helpers, it's also necessary to move
pause_on_fail(), and EXIT_STATUS and RET.
Existing lib.sh users might be using these same names for their functions
or variables. However lib.sh is always sourced near the top of the
file (checked), and whatever new definitions will simply override the ones
provided by lib.sh.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://patch.msgid.link/edd3785a3bd72ffbe1409300989e993ee50ae98b.1731589511.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Update .gitignore in selftest to skip conntrack_reverse_clash,
from Li Zhijian.
2) Fix conntrack_dump_flush return values, from Guan Jing.
3) syzbot found that ipset's bitmap type does not properly checks for
bitmap's first ip, from Jeongjun Park.
* tag 'nf-24-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: ipset: add missing range check in bitmap_ip_uadt
selftests: netfilter: Fix missing return values in conntrack_dump_flush
selftests: netfilter: Add missing gitignore file
====================
Link: https://patch.msgid.link/20241114125723.82229-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin KaFai Lau says:
====================
pull-request: bpf-next 2024-11-14
We've added 9 non-merge commits during the last 4 day(s) which contain
a total of 3 files changed, 226 insertions(+), 84 deletions(-).
The main changes are:
1) Fixes to bpf_msg_push/pop_data and test_sockmap. The changes has
dependency on the other changes in the bpf-next/net branch,
from Zijian Zhang.
2) Drop netns codes from mptcp test. Reuse the common helpers in
test_progs, from Geliang Tang.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
bpf, sockmap: Fix sk_msg_reset_curr
bpf, sockmap: Several fixes to bpf_msg_pop_data
bpf, sockmap: Several fixes to bpf_msg_push_data
selftests/bpf: Add more tests for test_txmsg_push_pop in test_sockmap
selftests/bpf: Add push/pop checking for msg_verify_data in test_sockmap
selftests/bpf: Fix total_bytes in msg_loop_rx in test_sockmap
selftests/bpf: Fix SENDPAGE data logic in test_sockmap
selftests/bpf: Add txmsg_pass to pull/push/pop in test_sockmap
selftests/bpf: Drop netns helpers in mptcp
====================
Link: https://patch.msgid.link/20241114202832.3187927-1-martin.lau@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the bug of some functions were missing return values.
Fixes: eff3c558bb ("netfilter: ctnetlink: support filtering by zone")
Signed-off-by: Guan Jing <guanjing@cmss.chinamobile.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Compiled binary files should be added to .gitignore
'git status' complains:
Untracked files:
(use "git add <file>..." to include in what will be committed)
net/netfilter/conntrack_reverse_clash
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* for-next/pkey-signal:
: Bring arm64 pkey signal delivery in line with the x86 behaviour
selftests/mm: Fix unused function warning for aarch64_write_signal_pkey()
selftests/mm: Define PKEY_UNRESTRICTED for pkey_sighandler_tests
selftests/mm: Enable pkey_sighandler_tests on arm64
selftests/mm: Use generic pkey register manipulation
arm64: signal: Remove unused macro
arm64: signal: Remove unnecessary check when saving POE state
arm64: signal: Improve POR_EL0 handling to avoid uaccess failures
firmware: arm_sdei: Fix the input parameter of cpuhp_remove_state()
Revert "kasan: Disable Software Tag-Based KASAN with GCC"
kasan: Fix Software Tag-Based KASAN with GCC
kasan: Disable Software Tag-Based KASAN with GCC
Documentation/protection-keys: add AArch64 to documentation
arm64: set POR_EL0 for kernel threads
# Conflicts:
# arch/arm64/kernel/signal.c
* arm64/for-next/perf:
perf: Switch back to struct platform_driver::remove()
perf: arm_pmuv3: Add support for Samsung Mongoose PMU
dt-bindings: arm: pmu: Add Samsung Mongoose core compatible
perf/dwc_pcie: Fix typos in event names
perf/dwc_pcie: Add support for Ampere SoCs
ARM: pmuv3: Add missing write_pmuacr()
perf/marvell: Marvell PEM performance monitor support
perf/arm_pmuv3: Add PMUv3.9 per counter EL0 access control
perf/dwc_pcie: Convert the events with mixed case to lowercase
perf/cxlpmu: Support missing events in 3.1 spec
perf: imx_perf: add support for i.MX91 platform
dt-bindings: perf: fsl-imx-ddr: Add i.MX91 compatible
drivers perf: remove unused field pmu_node
* for-next/gcs: (42 commits)
: arm64 Guarded Control Stack user-space support
kselftest/arm64: Fix missing printf() argument in gcs/gcs-stress.c
arm64/gcs: Fix outdated ptrace documentation
kselftest/arm64: Ensure stable names for GCS stress test results
kselftest/arm64: Validate that GCS push and write permissions work
kselftest/arm64: Enable GCS for the FP stress tests
kselftest/arm64: Add a GCS stress test
kselftest/arm64: Add GCS signal tests
kselftest/arm64: Add test coverage for GCS mode locking
kselftest/arm64: Add a GCS test program built with the system libc
kselftest/arm64: Add very basic GCS test program
kselftest/arm64: Always run signals tests with GCS enabled
kselftest/arm64: Allow signals tests to specify an expected si_code
kselftest/arm64: Add framework support for GCS to signal handling tests
kselftest/arm64: Add GCS as a detected feature in the signal tests
kselftest/arm64: Verify the GCS hwcap
arm64: Add Kconfig for Guarded Control Stack (GCS)
arm64/ptrace: Expose GCS via ptrace and core files
arm64/signal: Expose GCS state in signal frames
arm64/signal: Set up and restore the GCS context for signal handlers
arm64/mm: Implement map_shadow_stack()
...
* for-next/probes:
: Various arm64 uprobes/kprobes cleanups
arm64: insn: Simulate nop instruction for better uprobe performance
arm64: probes: Remove probe_opcode_t
arm64: probes: Cleanup kprobes endianness conversions
arm64: probes: Move kprobes-specific fields
arm64: probes: Fix uprobes for big-endian kernels
arm64: probes: Fix simulate_ldr*_literal()
arm64: probes: Remove broken LDR (literal) uprobe support
* for-next/asm-offsets:
: arm64 asm-offsets.c cleanup (remove unused offsets)
arm64: asm-offsets: remove PREEMPT_DISABLE_OFFSET
arm64: asm-offsets: remove DMA_{TO,FROM}_DEVICE
arm64: asm-offsets: remove VM_EXEC and PAGE_SZ
arm64: asm-offsets: remove MM_CONTEXT_ID
arm64: asm-offsets: remove COMPAT_{RT_,SIGFRAME_REGS_OFFSET
arm64: asm-offsets: remove VMA_VM_*
arm64: asm-offsets: remove TSK_ACTIVE_MM
* for-next/tlb:
: TLB flushing optimisations
arm64: optimize flush tlb kernel range
arm64: tlbflush: add __flush_tlb_range_limit_excess()
* for-next/misc:
: Miscellaneous patches
arm64: tls: Fix context-switching of tpidrro_el0 when kpti is enabled
arm64/ptrace: Clarify documentation of VL configuration via ptrace
acpi/arm64: remove unnecessary cast
arm64/mm: Change protval as 'pteval_t' in map_range()
arm64: uprobes: Optimize cache flushes for xol slot
acpi/arm64: Adjust error handling procedure in gtdt_parse_timer_block()
arm64: fix .data.rel.ro size assertion when CONFIG_LTO_CLANG
arm64/ptdump: Test both PTE_TABLE_BIT and PTE_VALID for block mappings
arm64/mm: Sanity check PTE address before runtime P4D/PUD folding
arm64/mm: Drop setting PTE_TYPE_PAGE in pte_mkcont()
ACPI: GTDT: Tighten the check for the array of platform timer structures
arm64/fpsimd: Fix a typo
arm64: Expose ID_AA64ISAR1_EL1.XS to sanitised feature consumers
arm64: Return early when break handler is found on linked-list
arm64/mm: Re-organize arch_make_huge_pte()
arm64/mm: Drop _PROT_SECT_DEFAULT
arm64: Add command-line override for ID_AA64MMFR0_EL1.ECV
arm64: head: Drop SWAPPER_TABLE_SHIFT
arm64: cpufeature: add POE to cpucap_is_possible()
arm64/mm: Change pgattr_change_is_safe() arguments as pteval_t
* for-next/mte:
: Various MTE improvements
selftests: arm64: add hugetlb mte tests
hugetlb: arm64: add mte support
* for-next/sysreg:
: arm64 sysreg updates
arm64/sysreg: Update ID_AA64MMFR1_EL1 to DDI0601 2024-09
* for-next/stacktrace:
: arm64 stacktrace improvements
arm64: preserve pt_regs::stackframe during exec*()
arm64: stacktrace: unwind exception boundaries
arm64: stacktrace: split unwind_consume_stack()
arm64: stacktrace: report recovered PCs
arm64: stacktrace: report source of unwind data
arm64: stacktrace: move dump_backtrace() to kunwind_stack_walk()
arm64: use a common struct frame_record
arm64: pt_regs: swap 'unused' and 'pmr' fields
arm64: pt_regs: rename "pmr_save" -> "pmr"
arm64: pt_regs: remove stale big-endian layout
arm64: pt_regs: assert pt_regs is a multiple of 16 bytes
* for-next/hwcap3:
: Add AT_HWCAP3 support for arm64 (also wire up AT_HWCAP4)
arm64: Support AT_HWCAP3
binfmt_elf: Wire up AT_HWCAP3 at AT_HWCAP4
* for-next/kselftest: (30 commits)
: arm64 kselftest fixes/cleanups
kselftest/arm64: Try harder to generate different keys during PAC tests
kselftest/arm64: Don't leak pipe fds in pac.exec_sign_all()
kselftest/arm64: Corrupt P0 in the irritator when testing SSVE
kselftest/arm64: Add FPMR coverage to fp-ptrace
kselftest/arm64: Expand the set of ZA writes fp-ptrace does
kselftets/arm64: Use flag bits for features in fp-ptrace assembler code
kselftest/arm64: Enable build of PAC tests with LLVM=1
kselftest/arm64: Check that SVCR is 0 in signal handlers
kselftest/arm64: Fix printf() compiler warnings in the arm64 syscall-abi.c tests
kselftest/arm64: Fix printf() warning in the arm64 MTE prctl() test
kselftest/arm64: Fix printf() compiler warnings in the arm64 fp tests
kselftest/arm64: Fix build with stricter assemblers
kselftest/arm64: Test signal handler state modification in fp-stress
kselftest/arm64: Provide a SIGUSR1 handler in the kernel mode FP stress test
kselftest/arm64: Implement irritators for ZA and ZT
kselftest/arm64: Remove unused ADRs from irritator handlers
kselftest/arm64: Correct misleading comments on fp-stress irritators
kselftest/arm64: Poll less often while waiting for fp-stress children
kselftest/arm64: Increase frequency of signal delivery in fp-stress
kselftest/arm64: Fix encoding for SVE B16B16 test
...
* for-next/crc32:
: Optimise CRC32 using PMULL instructions
arm64/crc32: Implement 4-way interleave using PMULL
arm64/crc32: Reorganize bit/byte ordering macros
arm64/lib: Handle CRC-32 alternative in C code
* for-next/guest-cca:
: Support for running Linux as a guest in Arm CCA
arm64: Document Arm Confidential Compute
virt: arm-cca-guest: TSM_REPORT support for realms
arm64: Enable memory encrypt for Realms
arm64: mm: Avoid TLBI when marking pages as valid
arm64: Enforce bounce buffers for realm DMA
efi: arm64: Map Device with Prot Shared
arm64: rsi: Map unprotected MMIO as decrypted
arm64: rsi: Add support for checking whether an MMIO is protected
arm64: realm: Query IPA size from the RMM
arm64: Detect if in a realm and set RIPAS RAM
arm64: rsi: Add RSI definitions
* for-next/haft:
: Support for arm64 FEAT_HAFT
arm64: pgtable: Warn unexpected pmdp_test_and_clear_young()
arm64: Enable ARCH_HAS_NONLEAF_PMD_YOUNG
arm64: Add support for FEAT_HAFT
arm64: setup: name 'tcr2' register
arm64/sysreg: Update ID_AA64MMFR1_EL1 register
* for-next/scs:
: Dynamic shadow call stack fixes
arm64/scs: Drop unused prototype __pi_scs_patch_vmlinux()
arm64/scs: Deal with 64-bit relative offsets in FDE frames
arm64/scs: Fix handling of DWARF augmentation data in CIE/FDE frames
