Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
Pull x86 platform driver updates from Ilpo Järvinen:
- alienware WMAX thermal interface support
- Split ACPI and platform device based amd/hsmp drivers
- AMD X3D frequency/cache mode switching support
- asus thermal policy fixes
- Disable C1 auto-demotion in suspend to allow entering the deepest
C-states
- Fix volume buttons on Thinkpad X12 Detachable Tablet Gen 1
- Replace intel_scu_ipc "workaround" with 32-bit IO
- Correct *_show() function error handling in panasonic-laptop
- Gemini Lake P2SB devfn correction
- think-lmi Admin/System certificate authentication support
- Disable WMI devices for shutdown, refactoring continues
- Vexia EDU ATLA 10 tablet support
- Surface Pro 9 5G (Arm/QCOM) support
- Misc cleanups / refactoring / improvements
* tag 'platform-drivers-x86-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (69 commits)
platform/x86: p2sb: Cache correct PCI bar for P2SB on Gemini Lake
platform/x86: panasonic-laptop: Return errno correctly in show callback
Documentation: alienware-wmi: Describe THERMAL_INFORMATION operation 0x02
alienware-wmi: create_thermal_profile() no longer brute-forces IDs
alienware-wmi: Adds support to Alienware x17 R2
alienware-wmi: extends the list of supported models
alienware-wmi: order alienware_quirks[] alphabetically
platform/x86/intel/pmt: allow user offset for PMT callbacks
platform/x86/amd/hsmp: Change the error type
platform/x86/amd/hsmp: Add new error code and error logs
platform/x86/amd: amd_3d_vcache: Add sysfs ABI documentation
platform/x86/amd: amd_3d_vcache: Add AMD 3D V-Cache optimizer driver
intel-hid: fix volume buttons on Thinkpad X12 Detachable Tablet Gen 1
platform/x86/amd/hsmp: mark hsmp_msg_desc_table[] as maybe_unused
platform/x86: asus-wmi: Use platform_profile_cycle()
platform/x86: asus-wmi: Fix inconsistent use of thermal policies
platform/x86: hp: hp-bioscfg: remove redundant if statement
MAINTAINERS: Update ISHTP ECLITE maintainer entry
platform/x86: x86-android-tablets: Add support for Vexia EDU ATLA 10 tablet
platform/x86: x86-android-tablets: Add support for getting i2c_adapter by PCI parent devname()
...
Pull ACPI updates from Rafael Wysocki:
"These include a couple of fixes, a new ACPI backlight quirk for Apple
MacbookPro11,2 and Air7,2 and a bunch of cleanups:
- Fix _CPC register setting issue for registers located in memory in
the ACPI CPPC library code (Lifeng Zheng)
- Use DEFINE_SIMPLE_DEV_PM_OPS in the ACPI battery driver, make it
use devm_ for initializing mutexes and allocating driver data, and
make it check the register_pm_notifier() return value (Thomas
Weißschuh, Andy Shevchenko)
- Make the ACPI EC driver support compile-time conditional and allow
ACPI to be built without CONFIG_HAS_IOPORT (Arnd Bergmann)
- Remove a redundant error check from the pfr_telemetry driver (Colin
Ian King)
- Rearrange the processor_perflib code in the ACPI processor driver
to avoid compiling x86-specific code on other architectures (Arnd
Bergmann)
- Add adev NULL check to acpi_quirk_skip_serdev_enumeration() and
make UART skip quirks work on PCI UARTs without an UID (Hans de
Goede)
- Force native backlight handling Apple MacbookPro11,2 and Air7,2 in
the ACPI video driver (Jonathan Denose)
- Switch several ACPI platform drivers back to using struct
platform_driver::remove() (Uwe Kleine-König)
- Replace strcpy() with strscpy() in multiple places in the ACPI
subsystem (Muhammad Qasim Abdul Majeed, Abdul Rahim)"
* tag 'acpi-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
ACPI: video: force native for Apple MacbookPro11,2 and Air7,2
ACPI: CPPC: Fix _CPC register setting issue
ACPI: Switch back to struct platform_driver::remove()
ACPI: x86: Add adev NULL check to acpi_quirk_skip_serdev_enumeration()
ACPI: x86: Make UART skip quirks work on PCI UARTs without an UID
ACPI: allow building without CONFIG_HAS_IOPORT
ACPI: processor_perflib: extend X86 dependency
ACPI: scan: Use strscpy() instead of strcpy()
ACPI: SBSHC: Use strscpy() instead of strcpy()
ACPI: SBS: Use strscpy() instead of strcpy()
ACPI: power: Use strscpy() instead of strcpy()
ACPI: pci_root: Use strscpy() instead of strcpy()
ACPI: pci_link: Use strscpy() instead of strcpy()
ACPI: event: Use strscpy() instead of strcpy()
ACPI: EC: Use strscpy() instead of strcpy()
ACPI: APD: Use strscpy() instead of strcpy()
ACPI: thermal: Use strscpy() instead of strcpy()
ACPI: battery: Check for error code from devm_mutex_init() call
ACPI: EC: make EC support compile-time conditional
ACPI: pfr_telemetry: remove redundant error check on ret
...
Pull chrome platform updates from Tzung-Bi Shih:
"Fixes:
- Fix a leak of fwnode refcount.
Cleanups:
- Drop unused I2C driver data
- Move back from platform_driver::remove_new() to
platform_driver::remove()"
* tag 'chrome-platform-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: Switch back to struct platform_driver::remove()
platform/chrome: cros_ec_typec: fix missing fwnode reference decrement
platform/chrome: Drop explicit initialization of struct i2c_device_id::driver_data to 0
Gemini Lake (Goldmont Plus) is an Apollo Lake (Goldmont) derived design and
as such has the P2SB at device.function 13.0, rather then at the default
31.1, just like Apollo Lake.
At a mapping to P2SB_DEVFN_GOLDMONT to p2sb_cpu_ids[] for Goldmont Plus,
so that the correct PCI bar gets cached.
This fixes P2SB unhiding not working on these devices, which fixes
SPI support for the bootrom SPI controller not working.
Fixes: 2841631a03 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241116154546.85761-1-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
WMAX_METHOD_THERMAL_INFORMATION has a *system description* operation
that outputs a buffer with the following structure:
out[0] -> Number of fans
out[1] -> Number of sensors
out[2] -> 0x00
out[3] -> Number of thermal modes
This is now used by create_thermal_profile() to retrieve available thermal
codes instead of brute-forcing every ID.
Tested on an Alienware x15 R1. Verified by checking ACPI tables of
supported models.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20241111183623.14691-1-kuurtb@gmail.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Merge updates of the ACPI battery and EC drivers, an ACPI Platform
Firmware Runtime (PFR) telemetry driver update and an ACPI OS support
layer change for 6.13-rc1:
- Use DEFINE_SIMPLE_DEV_PM_OPS in the ACPI battery driver, make it use
devm_ for initializing mutexes and allocating driver data, and make
it check the register_pm_notifier() return value (Thomas Weißschuh,
Andy Shevchenko).
- Make the ACPI EC driver support compile-time conditional and allow
ACPI to be built without CONFIG_HAS_IOPORT (Arnd Bergmann).
- Remove a redundant error check from the pfr_telemetry driver (Colin
Ian King).
* acpi-battery:
ACPI: battery: Check for error code from devm_mutex_init() call
ACPI: battery: use DEFINE_SIMPLE_DEV_PM_OPS
ACPI: battery: initialize mutexes through devm_ APIs
ACPI: battery: allocate driver data through devm_ APIs
ACPI: battery: check result of register_pm_notifier()
* acpi-ec:
ACPI: EC: make EC support compile-time conditional
* acpi-pfr:
ACPI: pfr_telemetry: remove redundant error check on ret
* acpi-osl:
ACPI: allow building without CONFIG_HAS_IOPORT
Rename the `omnia_mcu_gpio_templates` variable to
`omnia_mcu_gpio_names`. The array contained templates for the names
during the development of the driver, but the template prefix `gpio%u.`
was dropped before the driver was merged, since this functionality was
broken in gpiolib.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add more comprehensive documentation for the driver private data
structure, `struct omnia_mcu`.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Volume buttons on Lenovo Thinkpad X12 Detachable Tablet Gen 1 did not
send any input events when pressed. When loading intel-hid with the 5
Button Array explicitly enabled, the buttons functioned normally.
Adds the X12 Detachable Tablet Gen 1 to the `button_array_table`.
However, the driver is unable to call INTEL_HID_DSM_BTNE_FN and prints
the warning "failed to set button capability" when attempting to enable
or disable the 5 Button Array. The warning should be harmless and
adding more special handling to avoid it is not worth it.
Co-developed-by: Mary Strodl <mstrodl@csh.rit.edu>
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Signed-off-by: Cole Stowell <cole@stowell.pro>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241107205908.69279-1-cole@stowell.pro
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
When changing the thermal policy using the platform profile API,
a Vivobook thermal policy is stored in throttle_thermal_policy_mode.
However everywhere else a normal thermal policy is stored inside this
variable, potentially confusing the platform profile.
Fix this by always storing normal thermal policy values inside
throttle_thermal_policy_mode and only do the conversion when writing
the thermal policy to hardware. This also fixes the order in which
throttle_thermal_policy_switch_next() steps through the thermal modes
on Vivobook machines.
Tested-by: Casey G Bowman <casey.g.bowman@intel.com>
Fixes: bcbfcebda2 ("platform/x86: asus-wmi: add support for vivobook fan profiles")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241107003811.615574-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Pull x86 platform driver fixes from Hans de Goede:
- AMD PMF: Add new hardware id
- AMD PMC: Fix crash when loaded with enable_stb=1 on devices without STB
- Dell: Add Alienware hwid for Alienware systems with Dell WMI interface
- thinkpad_acpi: Quirk to fix wrong fan speed readings on L480
- New hotkey mappings for Dell and Lenovo laptops
* tag 'platform-drivers-x86-v6.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: thinkpad_acpi: Fix for ThinkPad's with ECFW showing incorrect fan speed
platform/x86: ideapad-laptop: add missing Ideapad Pro 5 fn keys
platform/x86: dell-wmi-base: Handle META key Lock/Unlock events
platform/x86: dell-smbios-base: Extends support to Alienware products
platform/x86/amd/pmc: Detect when STB is not available
platform/x86/amd/pmf: Add SMU metrics table support for 1Ah family 60h model
Add support for the Vexia EDU ATLA 10 tablet, Android 4.2/4.4 + Guadalinex
Ubuntu tablet distributed to schools in the Spanish Andalucía region.
Besides the usual broken DSDT issues this tablet is special because all
its LPSS island peripherals are enumerated as PCI devices rather then as
ACPI devices as they typically are.
At the same time there are disabled (_STA=0) ACPI devices for
the peripherals and child ACPI devices for e.g. attached I2C/SDIO devices
are children of these disabled ACPI devices and thus will not be used
by Linux since the parent is disabled.
So besides the usual manual i2c-client instantiation for accel/touchscreen
this tablet also requires manual i2c-client instantiation for the codec
and for the PMIC.
Also it seems the mainboard was designed for Windows not Android, so
it has an I2C attached embedded controller instead of allowing direct
access to the charger + fuel-gauge chips as is usual with Android boards.
Normally when there is an embedded controller, there also is ACPI battery
support, but since this shipped with Android that is missing and Linux
needs to have a power_supply class driver talking directly to the EC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241104200848.58693-4-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
On the Vexia EDU ATLA 10 tablet, which ships with Android + a custom Linux
(guadalinex) using the custom Android kernel the I2C controllers are not
enumerated as ACPI devices as they typically are.
Instead they are enumerated as PCI devices which do not have ACPI firmware
nodes associated with them, so getting the i2c_adapter by the ACPI path of
its firmware node does not work.
Add support for getting the i2c_adapter by the devname() of its PCI parent
instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241104200848.58693-3-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Use platform_get_resource() to fetch the memory resource instead of
acpi_walk_resources() and devm_ioremap_resource() for mapping the
resources.
PS: We cannot use resource_size() here because it adds an extra byte to
round off the size. In the case of PMF ResourceTemplate(), this rounding
is already handled within the _CRS. Using resource_size() would increase
the resource size by 1, causing a mismatch with the length field and
leading to issues. Therefore, simply use end-start of the ACPI resource to
obtain the actual length.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20241104054829.620858-4-Shyam-sundar.S-k@amd.com
[ij: added a cast to resource_size_t printing]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The scancodes for the Mic Mute and Airplane keys on the Ideapad Pro 5
(14AHP9 at least, probably the other variants too) are different and
were not being picked up by the driver. This adds them to the keymap.
Apart from what is already supported, the remaining fn keys are
unfortunately producing windows-specific key-combos.
Signed-off-by: Renato Caldas <renato@calgera.com>
Link: https://lore.kernel.org/r/20241102183116.30142-1-renato@calgera.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some Alienware devices have a key that locks/unlocks the Meta key. This
key triggers a WMI event that should be ignored by the kernel, as it's
handled by internally the firmware.
There is no known way of changing this default behavior. The firmware
would lock/unlock the Meta key, regardless of how the event is handled.
Tested on an Alienware x15 R1.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20241031154441.6663-2-kuurtb@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes the following error:
dell_smbios: Unable to run on non-Dell system
Which is triggered after dell-wmi driver fails to initialize on
Alienware systems, as it depends on dell-smbios.
This effectively extends dell-wmi, dell-smbios and dcdbas support to
Alienware devices, that might share some features of the SMBIOS intereface
calling interface with other Dell products.
Tested on an Alienware X15 R1.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20241031154023.6149-2-kuurtb@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Loading the amd_pmc module as:
amd_pmc enable_stb=1
...can result in the following messages in the kernel ring buffer:
amd_pmc AMDI0009:00: SMU cmd failed. err: 0xff
ioremap on RAM at 0x0000000000000000 - 0x0000000000ffffff
WARNING: CPU: 10 PID: 2151 at arch/x86/mm/ioremap.c:217 __ioremap_caller+0x2cd/0x340
Further debugging reveals that this occurs when the requests for
S2D_PHYS_ADDR_LOW and S2D_PHYS_ADDR_HIGH return a value of 0,
indicating that the STB is inaccessible. To prevent the ioremap
warning and provide clarity to the user, handle the invalid address
and display an error message.
Link: https://lore.kernel.org/platform-driver-x86/c588ff5d-3e04-4549-9a86-284b9b4419ba@amd.com
Fixes: 3d7d407dfb ("platform/x86: amd-pmc: Add support for AMD Spill to DRAM STB feature")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Corey Hickey <bugfood-c@fatooh.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20241028180241.1341624-1-bugfood-ml@fatooh.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Implements platform profile support for Dell laptops with new WMAX thermal
interface, present on some Alienware X-Series, Alienware M-Series and
Dell's G-Series laptops. This interface is suspected to be used by
Alienware Command Center (AWCC), which is not available for linux
systems, to manage thermal profiles.
This implementation makes use of three WMI methods, namely
THERMAL_CONTROL, THERMAL_INFORMATION and GAME_SHIFT_STATUS, which take
u32 as input and output arguments. Each method has a set of supported
operations specified in their respective enums.
Not all models with WMAX WMI interface support these methods. Because of
this, models have to manually declare support through new quirks
`thermal` for THERMAL_CONTROL and THERMAL_INFORMATION and `gmode` for
GAME_SHIFT_STATUS.
Wrappers written for these methods support multiple operations.
THERMAL_CONTROL switches thermal modes through operation
ACTIVATE_PROFILE. Available thermal codes are auto-detected at runtime
and matched against a list of known thermal codes:
Thermal Table "User Selectable Thermal Tables" (USTT):
BALANCED 0xA0
BALANCED_PERFORMANCE 0xA1
COOL 0xA2
QUIET 0xA3
PERFORMANCE 0xA4
LOW_POWER 0xA5
Thermal Table Basic:
QUIET 0x96
BALANCED 0x97
BALANCED_PERFORMANCE 0x98
PERFORMANCE 0x99
Devices are known to implement only one of these tables without mixing
their thermal codes.
The fact that the least significant digit of every thermal code is
consecutive of one another is exploited to efficiently match codes
through arrays.
Autodetection of available codes is done through operation LIST_IDS of
method THERMAL_INFORMATION. This operation lists fan IDs, CPU sensor ID,
GPU sensor ID and available thermal profile codes, *in that order*. As
number of fans and thermal codes is very model dependent, almost every
ID is scanned and matched based on conditions found on
is_wmax_thermal_code(). The known upper bound for the number of IDs is
13, corresponding to a device that have 4 fans, 2 sensors and 7 thermal
codes.
Additionally G-Series laptops have a key called G-key, which (with AWCC
proprietary driver) switches the thermal mode to an special mode named
GMODE with code 0xAB and changes Game Shift Status to 1. Game Shift is a
mode the manufacturer claims, increases gaming performance.
GAME_SHIFT_STATUS method is used to mimic this behavior when selecting
PLATFORM_PROFILE_PERFORMANCE option.
All of these profiles are known to only change fan speed profiles,
although there are untested claims that some of them also change power
profiles.
Activating a thermal mode with method THERMAL_CONTROL may cause short
hangs. This is a known problem present on every platform.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241030001124.7589-1-kuurtb@gmail.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/platform/chrome to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241028082611.431723-2-u.kleine-koenig@baylibre.com
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Pull x86 platform driver fixes from Hans de Goede:
- Asus thermal profile fix, fixing performance issues on Lunar Lake
- Intel PMC: one revert for a lockdep issue and one bugfix
- Dell WMI: Ignore some WMI events on suspend/resume to silence warnings
* tag 'platform-drivers-x86-v6.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Fix thermal profile initialization
platform/x86: dell-wmi: Ignore suspend notifications
platform/x86/intel/pmc: Fix pmc_core_iounmap to call iounmap for valid addresses
platform/x86:intel/pmc: Revert "Enable the ACPI PM Timer to be turned off when suspended"
