drm/i915 feature pull for v6.17:
Features and functionality:
- Add support for DSC fractional link bpp on DP MST (Imre)
- Add support for simultaneous Panel Replay and Adaptive Sync (Jouni)
- Add support for PTL+ double buffered LUT registers (Chaitanya, Ville)
- Add PIPEDMC event handling in preparation for flip queue (Ville)
Refactoring and cleanups:
- Rename lots of DPLL interfaces to unify them (Suraj)
- Allocate struct intel_display dynamically (Jani)
- Abstract VLV IOSF sideband better (Jani)
- Use str_true_false() helper (Yumeng Fang)
- Refactor DSB code in preparation for flip queue (Ville)
- Use drm_modeset_lock_assert_held() instead of open coding (Luca)
- Remove unused arg from skl_scaler_get_filter_select() (Luca)
- Split out a separate display register header (Jani)
- Abstract DRAM detection better (Jani)
- Convert LPT/WPT SBI sideband to struct intel_display (Jani)
Fixes:
- Fix DSI HS command dispatch with forced pipeline flush (Gareth Yu)
- Fix BMG and LNL+ DP adaptive sync SDP programming (Ankit)
- Fix error path for xe display workqueue allocation (Haoxiang Li)
- Disable DP AUX access probe where not required (Imre)
- Fix DKL PHY access if the port is invalid (Luca)
- Fix PSR2_SU_STATUS access on ADL+ (Jouni)
- Add sanity checks for porch and sync on BXT/GLK DSI (Ville)
DRM core changes:
- Change AUX DPCD access probe address (Imre)
- Refactor EDID quirks, amd make them available to drivers (Imre)
- Add quirk for DPCD access probe (Imre)
- Add DPCD definitions for Panel Replay capabilities (Jouni)
Merges:
- Backmerges to sync with v6.15-rcs and v6.16-rc1 (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/fff9f231850ed410bd81b53de43eff0b98240d31@intel.com
Reading DPCD registers has side-effects and some of these can cause a
problem for instance during link training. Based on this it's better to
avoid the probing quirk done before each DPCD register read, limiting
this to the monitor which requires it. Add an EDID quirk for this. Leave
the quirk enabled by default, allowing it to be disabled after the
monitor is detected.
v2: Fix lockdep wrt. drm_dp_aux::hw_mutex when calling
drm_dp_dpcd_set_probe_quirk() with a dependent lock already held.
v3: Add a helper for determining if DPCD probing is needed. (Jani)
v4:
- s/drm_dp_dpcd_set_probe_quirk/drm_dp_dpcd_set_probe (Jani)
- Fix documentation of drm_dp_dpcd_set_probe().
- Add comment at the end of internal quirk entries.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250609125556.109538-1-imre.deak@intel.com
Add generic CEC helpers to be used by HDMI drivers. Both notifier and
and adapter are supported for registration. Once registered, the driver
can call common set of functions to update physical address, to
invalidate it or to unregister CEC data. Unlike drm_connector_cec_funcs
(which provides interface common to all implementations, including, but
not limited to the CEC adapter, CEC notifier, CEC pin-based adapter,
etc) the struct drm_connector_hdmi_cec_adapter_ops provides callbacks
specific to the CEC adapter implementations.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250517-drm-hdmi-connector-cec-v6-5-35651db6f19b@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Some older NVIDIA and some newer NVIDIA hardware/firmware seems to
have issues with address only transactions (firmware rejects them).
Add an option to the core drm dp to avoid address only transactions,
This just puts the MOT flag removal on the last message of the transfer
and avoids the start of transfer transaction.
This with the flag set in nouveau, allows eDP probing on GB203 device.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Reviewed-by: Timur Tabi <ttabi@nvidia.com>
Tested-by: Timur Tabi <ttabi@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Non-display related:
- Fix undefined reference to `intel_pxp_gsccs_is_ready_for_sessions'
Display related:
- More work towards display separation (Jani)
- Stop writing VRR_CTL_IGN_MAX_SHIFT for MTL onwards (Jouni)
- DSC checks for 3 engines (Ankit)
- Add link rate and lane count to i915_display_info (Khaled)
- PSR fixes and workaround for underrun on idle (Jouni)
- LOBF enablement and ALMP fixes (Animesh)
- Clean up VGA plane handling (Ville)
- Use an intel_connector pointer everywhere (Imre)
- Fix warning for coffeelake on SunrisePoint PCH (Jiajia)
- Rework/Correction on minimum hblank calculation (Arun)
- Dmesg clean up (Jani)
- Add a couple of simple display workarounds (Ankit, Vinod)
- Refactor HDCP GSC (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/aByyL3bEufPu79OM@intel.com
Unify the function to calculate the link symbol cycles for both dsc and
non-dsc case and export the function so that it can be used in the
respective platform display drivers for other calculations.
v2: unify the fn for both dsc and non-dsc case (Imre)
v3: rename drm_dp_link_symbol_cycles to drm_dp_link_data_symbol_cycles
retain slice_eoc_cycles as is (Imre)
v4: Expose only drm_dp_link_symbol_cycles() (Imre)
v6: Add slice pixels which was removed unknowingly (Vinod)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250424-hblank-v7-1-8b002f1506cc@intel.com
HDMI standard defines recommended N and CTS values for Audio Clock
Regeneration. Currently each driver implements those, frequently in
somewhat unique way. Provide a generic helper for getting those values
to be used by the HDMI drivers.
The helper is added to drm_hdmi_helper.c rather than drm_hdmi_audio.c
since HDMI drivers can be using this helper function even without
switching to DRM HDMI Audio helpers.
Note: currently this only handles the values per HDMI 1.4b Section 7.2
and HDMI 2.0 Section 9.2.1. Later the table can be expanded to
accommodate for Deep Color TMDS char rates per HDMI 1.4 Appendix D
and/or HDMI 2.0 / 2.1 Appendix C).
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250408-drm-hdmi-acr-v2-1-dee7298ab1af@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
drm/i915 feature pull for v6.15:
Features and functionality:
- Enable DP 128b/132b SST DSC (Jani, Imre)
- Allow DSB to perform commits when VRR is enabled (Ville)
- Compute HDMI PLLs for SNPS/C10 PHYs for rates not in fixed tables (Ankit)
- Allow DSB usage when PSR is enabled on LNL+ (Jouni)
- Enable Panel Replay mode change without full modeset (Jouni)
- Enable async flips with compressed buffers on ICL+ (Ville)
- Support luminance based brightness control via DPCD for eDP (Suraj)
- Enable VRR enable/disable without full modeset (Mitul, Ankit)
- Add debugfs facility for force testing HDCP 1.4 (Suraj)
- Add scaler tracepoints, improve plane tracepoints (Ville)
- Improve DMC wakelock debugging facilities (Gustavo)
- Allow GuC SLPC default strategies on MTL+ for performance (Rodrigo)
- Provide more information on display faults (Ville)
Refactoring and cleanups:
- Continue conversions to struct intel_display (Ville, Jani, Suraj, Imre)
- Joiner and Y plane reorganization (Ville)
- Move HDCP debugfs to intel_hdcp.c (Jani)
- Clean up and unify LSPCON interfaces (Jani)
- Move code out of intel_display.c to reduce its size (Ville)
- Clean up and simplify DDI port enabling/disabling (Imre)
- Make LPT LP a dedicated PCH type, refactor (Jani)
- Simplify DSC range BPG offset calculation (Ankit)
- Scaler cleanups (Ville)
- Remove unused code from GVT (David Alan Gilbert)
- Improve plane debugging (Ville)
- DSB and VRR refactoring (Ville)
Fixes:
- Check if vblank is sufficient for DSC prefill and scaler (Mitul)
- Fix Mesa clear color alignment regression (Ville)
- Add missing TC DP PHY lane stagger delay (Imre)
- Fix DSB + VRR usage for PTL+ (Ville)
- Improve robustness of display VT-d workarounds (Ville)
- Fix platforms for dbuf tracker state service programming (Ravi)
- Fix DMC wakelock support conditions (Gustavo)
- Amend DMC wakelock register ranges (Gustavo)
- Disable the Common Primary Timing Generator (CMTG) (Gustavo)
- Enable C20 PHY SSC (Suraj)
- Add workaround for DKL PHY DP mode write (Nemesa)
- Fix build warnings on clamp() usage (Guenter Roeck, Ankit)
- Fix error handling while adding a connector (Imre)
- Avoid full modeset at probe on vblank delay mismatches (Ville)
- Fix encoder HDMI check for HDCP line rekeying (Suraj)
- Fix HDCP repeater authentication during topology change (Suraj)
- Handle display PHY power state reset for power savings (Mika)
- Fix typos all over the place (Nitin)
- Update HDMI TMDS C20 parameters for various platforms (Dnyaneshwar)
- Guarantee a minimum hblank time for 128b/132b and 8b/10b MST (Arun, Imre)
- Do not hardcode LSPCON settle timeout (Giedrius Statkevičius)
Xe driver changes:
- Re-use display vmas when possible (Maarten)
- Remove double pageflip (Maarten)
- Enable DP tunneling (Imre)
- Separate i915 and xe tracepoints (Ville)
DRM core changes:
- Increase DPCD eDP display control CAP size to 5 bytes (Suraj)
- Add DPCD eDP version 1.5 definition (Suraj)
- Add timeout parameter to drm_lspcon_set_mode() (Giedrius Statkevičius)
Merges:
- Backmerge drm-next (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87h64j7b7n.fsf@intel.com
According to the DisplayPort standard, LTTPRs have two operating
modes:
- non-transparent - it replies to DPCD LTTPR field specific AUX
requests, while passes through all other AUX requests
- transparent - it passes through all AUX requests.
Switching between this two modes is done by the DPTX by issuing
an AUX write to the DPCD PHY_REPEATER_MODE register.
Add a generic helper that allows switching between these modes.
Also add a generic wrapper for the helper that handles the explicit
disabling of non-transparent mode and its disable->enable sequence
mentioned in the DP Standard v2.0 section 3.6.6.1. Do this in order
to move this handling out of the vendor specific driver implementation
into the generic framework.
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250203-drm-dp-msm-add-lttpr-transparent-mode-set-v5-1-c865d0e56d6e@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Extended wake timeout request helps to give additional
time by reading the DPCD register through which sink requests the
minimal amount of time required to wake the sink up.
Source device shall keep retying the AUX tansaction till the
extended timeout that is being granted for LTTPRs from the
sink device.
--v2
-Add documentation [Dmitry]
Spec: DP v2.1 Section 3.6.12.3
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-3-suraj.kandpal@intel.com
[Why]
The RAD of sideband message printed today is incorrect.
For RAD stored within MST branch
- If MST branch LCT is 1, it's RAD array is untouched and remained as 0.
- If MST branch LCT is larger than 1, use nibble to store the up facing
port number in cascaded sequence as illustrated below:
u8 RAD[0] = (LCT_2_UFP << 4) | LCT_3_UFP
RAD[1] = (LCT_4_UFP << 4) | LCT_5_UFP
...
In drm_dp_mst_rad_to_str(), it wrongly to use BIT_MASK(4) to fetch the port
number of one nibble.
[How]
Adjust the code by:
- RAD array items are valuable only for LCT >= 1.
- Use 0xF as the mask to replace BIT_MASK(4)
V2:
- Document how RAD is constructed (Imre)
V3:
- Adjust the comment for rad[] so kdoc formats it properly (Lyude)
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113091100.3314533-2-Wayne.Lin@amd.com
Driver Changes:
- Some DG2 refactor to fix DG2 bugs when operating with certain CPUs (Raag)
- Use hw support for min/interim ddb allocation for async flip (Vinod)
- More general code refactor to allow full display separation (Jani)
- Expose dsc sink max slice count via debugfs (Swati)
- Fix C10 pll programming sequence (Suraj)
- Fix DG1 power gate sequence (Rodrigo)
- Use preemption timeout on selftest cleanup (Janusz)
- DP DSC related fixes (Ankit)
- Fix HDCP compliance test (Suraj)
- Clean and Optimise mtl_ddi_prepare_link_retrain (Suraj)
- Adjust Added Wake Time with PKG_C_LATENCY (Animesh)
- Enabling uncompressed 128b/132b UHBR SST (Jani)
- Handle hdmi connector init failures, and no HDMI/DP cases (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Z31_WPbBoHkwgEA9@intel.com
The struct drm_dp_mst_topology_mgr *mgr parameter is only used for debug
logging in case the passed in link rate or lane count are zero. There's
no further error checking as such, and the function returns 0.
There should be no case where the parameters are zero. The returned
value is generally used as a divisor, and if we were hitting this, we'd
be seeing division by zero.
Just remove the debug logging altogether, along with the mgr parameter,
so that the function can be used in non-MST contexts without the
topology manager.
v2: Also remove drm_dp_mst_helper_tests_init as unnecessary (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/72d77e7a7fe69c784e9df048b7e6f250fd7599e4.1735912293.git.jani.nikula@intel.com
The v6.13-rc2 release included a bunch of breaking changes,
specifically the MODULE_IMPORT_NS commit.
Backmerge in order to fix them before the next pull-request.
Include the fix from Stephen Roswell.
Caused by commit
25c3fd1183 ("drm/virtio: Add a helper to map and note the dma addrs and lengths")
Interacting with commit
cdd30ebb1b ("module: Convert symbol namespace to string literal")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20241209121717.2abe8026@canb.auug.org.au
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
If the MST topology is removed during the reception of an MST down reply
or MST up request sideband message, the
drm_dp_mst_topology_mgr::up_req_recv/down_rep_recv states could be reset
from one thread via drm_dp_mst_topology_mgr_set_mst(false), racing with
the reading/parsing of the message from another thread via
drm_dp_mst_handle_down_rep() or drm_dp_mst_handle_up_req(). The race is
possible since the reader/parser doesn't hold any lock while accessing
the reception state. This in turn can lead to a memory corruption in the
reader/parser as described by commit bd2fccac61 ("drm/dp_mst: Fix MST
sideband message body length check").
Fix the above by resetting the message reception state if needed before
reading/parsing a message. Another solution would be to hold the
drm_dp_mst_topology_mgr::lock for the whole duration of the message
reception/parsing in drm_dp_mst_handle_down_rep() and
drm_dp_mst_handle_up_req(), however this would require a bigger change.
Since the fix is also needed for stable, opting for the simpler solution
in this patch.
Cc: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org>
Fixes: 1d082618bb ("drm/display/dp_mst: Fix down/up message handling after sink disconnect")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13056
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-2-imre.deak@intel.com
Sync with v6.11-rc1 in general, and specifically get the new
BACKLIGHT_POWER_ constants for power states.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
