It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 43eb12d789 ("Bluetooth: Fix/implement Three-wire reliable packet sending")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 166d2f6a43 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 803b58367f ("Bluetooth: btusb: Implement driver internal packet reassembly")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
skb allocated by __hci_cmd_sync would not be used whether in checking
for supported iBT hardware variants or after, we should free it in all
error branches, this patch makes the case read version failed or default
error case free skb before return.
Fixes: c86c7285bb ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version")
Fixes: 019a1caa7f ("Bluetooth: btintel: Refactoring setup routine for bootloader devices")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btintel.c:1041:38: warning: cast to restricted __le32
drivers/bluetooth/btintel.c:1786:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1795:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1796:25: warning: cast to restricted __le16
drivers/bluetooth/btintel.c:1797:25: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:3426:28: warning: cast to restricted __le32
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
after probe() failure.
Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple
machines. This driver adds support for the Bluetooth function which
exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress.
This chip is present e.g. on muRata 2AE module.
This chip has additional quirk where the HCI command 0xfc45, used on
older chips to switch UART clock from 24 MHz to 48 MHz, to support
baudrates over 3 Mbdps, is no longer recognized by this newer chip.
This newer chip can configure the 4 Mbdps baudrate without the need
to issue HCI command 0xfc45, so add flag to indicate this and do not
issue the command on this chip to avoid failure to set 4 Mbdps baud
rate.
It is not clear whether there is a way to determine which chip does
and which chip does not support the HCI command 0xfc45, other than
trial and error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows
driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10)
Windows driver download address:
https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/
thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads
/driver-list/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
poll_sync has been proven to fix races of USB data and event endpoints
so this enables it by default.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the
default behavior of Bluetooth USB controller with respect to poll
synchronization of its endpoits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
The current version of the configuration structure has unaligned
16-bit fields, but according to the specification [1], access to
the configuration space must be aligned.
Add a second, aligned version of the configuration structure
and a new feature bit indicating that this version is being used.
[1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise
it will fall back to the hci_uart_wakeup or the behavior that can be
overridden before calling the hci_uart_register_device().
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For USB ALT 6 settings some Realtek chips need to transmit mSBC data
continuously without the zero length of USB packets.
In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior.
Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific
chip model for the behavior.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds a data structure for btrealtek object, and the
definition of vendor behavior flags. It also adds macros to set/test/get
the flags.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device removal is clearly out of virtio spec: it attempts to remove
unused buffers from a VQ before invoking device reset. To fix, make
open/close NOPs and do all cleanup/setup in probe/remove.
NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is
not really what a driver is supposed to be doing. These are transport
enable/disable callbacks from the BT core towards the driver. It maps to
a device being enabled/disabled by something like bluetoothd for
example. So if disabled, users expect that no resources/queues are in
use. It does work with all other transports like USB, SDIO, UART etc.
There should be no buffer used if the device is powered off. We also
don’t have any USB URBs in-flight if the transport is not active.
The way to implement a proper fix would be using vq reset if supported,
or even using a full device reset.
The cost of the hack is a single skb wasted on an unused bt device.
NB2: with this fix in place driver still suffers from a race condition
if an interrupt triggers while device is being reset. To fix, in the
virtbt_close() callback we should deactivate all interrupts. To be
fixed.
squashed fixup: bluetooth: virtio_bt: fix an error code in probe()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220811080943.198245-1-mst@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
The USB interface between the host and the bluetooth adapter used for
SCO packets uses an USB isochronous endpoint with a fragmentation scheme
that does not tolerate errors. Except USB isochronous transfers do
not provide a reliable stream with guaranteed delivery. (There is no
retry on error, see USB spec v2.0 5.6 and 8.5.5.)
To fragment a packet, the bluetooth HCI simply splits it in parts and
transfer them as-is. The receiver is expected to reconstruct the packet
by assuming the first fragment contains the header and parsing its size
field. There is no error detection either.
If a fragment is lost, the end result is that the kernel is no longer
synchronized and will pass malformed data to the upper layers, since it
has no way to tell if the first fragment is an actual first fragment or
a continuation fragment. Resynchronization can only happen by luck and
requires an unbounded amount of time.
The typical symptom for a HSP/HFP bluetooth headset is that the
microphone stops working and dmesg contains piles of rate-limited
"Bluetooth: hci0: SCO packet for unknown connection handle XXXX"
errors for an indeterminate amount of time, until the kernel accidentally
resynchronize.
A workaround is to ask the upper layer to prevalidate the first fragment
header. This is not possible with user channels so this workaround is
disabled in this case.
This problem is the most severe when using an ath3k adapter on an i.MX 6
board, where packet loss occur regularly, possibly because it is an USB1
device connected on an USB2 hub and this is a special case requiring
split transactions.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case of suspend/resume and HCI_RESET (BT On and Off),
ISOC endpoint set to alt setting 0 when no SCO connection exists.
This patch shall avoid resetting of ISOC endpoint to alt setting to 0.
Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The rationale of showing this is that it's potentially critical
information to diagnose and find more CSR compatibility bugs in the
future and it will save a lot of headaches.
Given that clones come from a wide array of vendors (some are actually
Barrot, some are something else) and these numbers are what let us find
differences between actual and fake ones, it will be immensely helpful
to scour the Internet looking for this pattern and building an actual
database to find correlations and improve the checks.
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
A patch series by a Qualcomm engineer essentially removed my
quirk/workaround because they thought it was unnecessary.
It wasn't, and it broke everything again:
https://patchwork.kernel.org/project/netdevbpf/list/?series=661703&archive=both&state=*
He argues that the quirk is not necessary because the code should check
if the dongle says if it's supported or not. The problem is that for
these Chinese CSR clones they say that it would work:
= New Index: 00:00:00:00:00:00 (Primary,USB,hci0)
= Open Index: 00:00:00:00:00:00
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
> [hci0] 11.276039
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 5.0 (0x09) - Revision 2064 (0x0810)
LMP version: Bluetooth 5.0 (0x09) - Subversion 8978 (0x2312)
Manufacturer: Cambridge Silicon Radio (10)
...
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0
> HCI Event: Command Complete (0x0e) plen 68
> [hci0] 11.668030
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Success (0x00)
Commands: 163 entries
...
Read Default Erroneous Data Reporting (Octet 18 - Bit 2)
Write Default Erroneous Data Reporting (Octet 18 - Bit 3)
...
...
< HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0
= Close Index: 00:1A:7D:DA:71:XX
So bring it back wholesale.
Fixes: 63b1a7dd38 ("Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING")
Fixes: e168f69008 ("Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR")
Fixes: 766ae2422b ("Bluetooth: hci_sync: Check LMP feature bit instead of quirk")
Cc: stable@vger.kernel.org
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address: ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1],
for rcu_sync_enter() is called without rcu_sync_init() due to
hci_uart_tty_open() ignoring percpu_init_rwsem() failure.
While we are at it, fix that hci_uart_register_device() ignores
percpu_init_rwsem() failure and hci_uart_unregister_device() does not
call percpu_free_rwsem().
Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f [1]
Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 67d2f8781b ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.")
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Based on photos available from the FCC, all currently supported RTL8761B
series USB dongles have the same chip: RTL8761BUV.
rtl8761bu is often used to refer to this chip.
rtl8761b sometimes refers to this chip, and other times to its
UART variant (RTL8761BTV).
+----------------+---------+---------+---------------+
| Dongle | USB VID | USB PID | FCC ID |
+----------------+---------+---------+---------------+
| ASUS USB-BT500 | 0x0b05 | 0x190e | MSQ-USBBTJB00 |
| TP-Link UB500 | 0x2357 | 0x0604 | 2AXJ4UB500 |
| EDUP EP-B3519 | | | 2AHRD-EPB3519 |
| EDUP EP-B3536 | | | 2AHRDEP-B3536 |
| UGREEN CM390 | | | 2AQI5-CM390 |
+----------------+---------+---------+---------------+
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
Fix up the packet type if ISO packets are sent over the bulk endpoint.
Note: This is a stopgap since the Bluetooth specification currently
doesn't define any endpoint to transport ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting"
instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI
commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so
remove this unnecessary quirk for fake CSR controllers.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
