Pull char / misc driver fixes from Greg KH:
"Here are a small number of various driver fixes for 6.7-rc7 that
normally come through the char-misc tree, and one debugfs fix as well.
Included in here are:
- iio and hid sensor driver fixes for a number of small things
- interconnect driver fixes
- brcm_nvmem driver fixes
- debugfs fix for previous fix
- guard() definition in device.h so that many subsystems can start
using it for 6.8-rc1 (requested by Dan Williams to make future
merges easier)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
debugfs: initialize cancellations earlier
Revert "iio: hid-sensor-als: Add light color temperature support"
Revert "iio: hid-sensor-als: Add light chromaticity support"
nvmem: brcm_nvram: store a copy of NVRAM content
dt-bindings: nvmem: mxs-ocotp: Document fsl,ocotp
driver core: Add a guard() definition for the device_lock()
interconnect: qcom: icc-rpm: Fix peak rate calculation
iio: adc: MCP3564: fix hardware identification logic
iio: adc: MCP3564: fix calib_bias and calib_scale range checks
iio: adc: meson: add separate config for axg SoC family
iio: adc: imx93: add four channels for imx93 adc
iio: adc: ti_am335x_adc: Fix return value check of tiadc_request_dma()
interconnect: qcom: sm8250: Enable sync_state
iio: triggered-buffer: prevent possible freeing of wrong buffer
iio: imu: inv_mpu6050: fix an error code problem in inv_mpu6050_read_raw
iio: imu: adis16475: use bit numbers in assign_bit()
iio: imu: adis16475: add spi_device_id table
iio: tmag5273: fix temperature offset
interconnect: Treat xlate() returning NULL node as an error
iio: common: ms_sensors: ms_sensors_i2c: fix humidity conversion time table
...
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of fixes to the new module load-time relocation code
- A fix for hwprobe overflowing on rv32
- A fix for to correctly decode C.SWSP and C.SDSP, which manifests in
misaligned access handling
- A fix for a boot-time shadow call stack initialization ordering issue
- A fix for Andes' errata probing, which was calling
riscv_noncoherent_supported() too late in the boot process and
triggering an oops
* tag 'riscv-for-linus-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: errata: andes: Probe for IOCP only once in boot stage
riscv: Fix SMP when shadow call stacks are enabled
dt-bindings: perf: riscv,pmu: drop unneeded quotes
riscv: fix misaligned access handling of C.SWSP and C.SDSP
RISC-V: hwprobe: Always use u64 for extension bits
Support rv32 ULEB128 test
riscv: Correct type casting in module loading
riscv: Safely remove entries from relocation list
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes are devicetree fixes for NXP, Mediatek, Rockchips
Arm machines as well as Microchip RISC-V, and most of these address
build-time warnings for spec violations and other minor issues. One of
the Mediatek warnings was enabled by default and prevented a clean
build.
The ones that address serious runtime issues are all on the i.MX
platform:
- a boot time panic on imx8qm
- USB hanging under load on imx8
- regressions on the imx93 ethernet phy
Code fixes include a minor error handling for the i.MX PMU driver, and
a number of firmware driver fixes:
- OP-TEE fix for supplicant based device enumeration, and a new sysfs
attribute to needed to fix a race against userspace
- Arm SCMI fix for possible truncation/overflow in the frequency
computations
- Multiple FF-A fixes for the newly added notification support"
* tag 'soc-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (55 commits)
MAINTAINERS: change the S32G2 maintainer's email address.
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
firmware: arm_scmi: Fix possible frequency truncation when using level indexing mode
firmware: arm_scmi: Fix frequency truncation by promoting multiplier type
...
Devicetree fixes for the 6.7-cycle.
All over the place this time. From adapting the size of the vdec nodes
on rk3328 and rk3399, fixing some wrong pinctrl settings on rk3128 and
the Turing RK1 board, emmc-settings fixes on rk3588 and interrupt-name
mishaps, down to some dt-cleanups.
Also this adds the missing rockchip,rk3588-pmugrf compatible to the soc
grf binding, that I somehow messed up during the pull requests for the
-rc1 . At least with it included the dt-checker is happier.
* tag 'v6.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
arm64: dts: rockchip: Fix Turing RK1 interrupt pinctrls
ARM: dts: rockchip: Fix sdmmc_pwren's pinmux setting for RK3128
arm64: dts: rockchip: minor whitespace cleanup around '='
ARM: dts: rockchip: minor whitespace cleanup around '='
dt-bindings: soc: rockchip: grf: add rockchip,rk3588-pmugrf
arm64: dts: rockchip: fix rk356x pcie msg interrupt name
arm64: dts: rockchip: Expand reg size of vdec node for RK3399
arm64: dts: rockchip: Expand reg size of vdec node for RK3328
Link: https://lore.kernel.org/r/2709704.mvXUDI8C0e@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull devicetree fixes from Rob Herring:
- Fix dt-extract-compatibles for builds with in tree build directory
- Drop Xinlei Lee <xinlei.lee@mediatek.com> bouncing email
- Fix the of_reconfig_get_state_change() return value documentation
- Add missing #power-domain-cells property to QCom MPM
- Fix warnings in i.MX LCDIF and adi,adv7533
* tag 'devicetree-fixes-for-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: adi,adv75xx: Document #sound-dai-cells
dt-bindings: lcdif: Properly describe the i.MX23 interrupts
dt-bindings: interrupt-controller: Allow #power-domain-cells
of: dynamic: Fix of_reconfig_get_state_change() return value documentation
dt-bindings: display: mediatek: dsi: remove Xinlei's mail
dt: dt-extract-compatibles: Don't follow symlinks when walking tree
i.MX fixes for 6.7:
- A MAINTAINERS update to reinstate freescale ARM64 DT directory in i.MX
entry.
- A series from Alexander Stein to fix #pwm-cells for imx8-ss.
- A series from Haibo Chen to fix GPIO node name for i.MX93 and
i.MX8ULP.
- Add parkmode-disable-ss-quirk for DWC3 on i.MX8MP and i.MX8MQ to fix
an issue that the controller may hang when processing transactions
under heavy USB traffic from multiple endpoints.
- Fix mediamix block power on/off for i.MX93 by correcting the power
domain clock to be 'nic_media'.
- A couple of Ethernet PHY clock regression fixes for imx6ul-pico and
imx6q-skov board.
- Fix edma3 power domain for i.MX8QM to fix a panic during startup
process.
* tag 'imx-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
ARM: dts: imx6q: skov: fix ethernet clock regression
arm64: dt: imx93: tqma9352-mba93xxla: Fix LPUART2 pad config
Link: https://lore.kernel.org/r/20231207005202.GF270430@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull pin control fixes from Linus Walleij:
- Fix a really interesting potential core bug in the list iterator
requireing the use of READ_ONCE() discovered when testing kernel
compiles with clang.
- Check devm_kcalloc() return value and an array bounds in the STM32
driver.
- Fix an exotic string truncation issue in the s32cc driver, found by
the kernel test robot (impressive!)
- Fix an undocumented struct member in the cy8c95x0 driver.
- Fix a symbol overlap with MIPS in the Lochnagar driver, MIPS defines
a global symbol "RST" which is a bit too generic and collide with
stuff. OK this one should be renamed too, we will fix that as well.
- Fix erroneous branch taking in the Realtek driver.
- Fix the mail address in MAINTAINERS for the s32g2 driver.
* tag 'pinctrl-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
dt-bindings: pinctrl: s32g2: change a maintainer email address
pinctrl: realtek: Fix logical error when finding descriptor
pinctrl: lochnagar: Don't build on MIPS
pinctrl: avoid reload of p state in list iteration
pinctrl: cy8c95x0: Fix doc warning
pinctrl: s32cc: Avoid possible string truncation
pinctrl: stm32: fix array read out of bound
pinctrl: stm32: Add check for devm_kcalloc
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
Pull SCSI fixes from James Bottomley:
"Seven small fixes, six in drivers and one in sd.
The sd fix is so large because it changes a struct pointer to a struct
but otherwise is fairly simple"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom-ufs: dt-bindings: Document the SM8650 UFS Controller
scsi: sd: Fix sshdr use in sd_suspend_common()
scsi: scsi_debug: Delete some bogus error checking
scsi: scsi_debug: Fix some bugs in sdebug_error_write()
scsi: ufs: core: Fix racing issue between ufshcd_mcq_abort() and ISR
scsi: ufs: core: Expand MCQ queue slot to DeviceQueueDepth + 1
scsi: qla2xxx: Fix system crash due to bad pointer access
When moving the *-internal-delay-ps properties to only apply for RGMII
interface modes there where a typo in the text formatting.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input updates from Dmitry Torokhov:
- a number of input drivers has been converted to use facilities
provided by the device core to instantiate driver-specific attributes
instead of using devm_device_add_group() and similar APIs
- platform input devices have been converted to use remove() callback
returning void
- a fix for use-after-free when tearing down a Synaptics RMI device
- a few flexible arrays in input structures have been annotated with
__counted_by to help hardening efforts
- handling of vddio supply in cyttsp5 driver
- other miscellaneous fixups
* tag 'input-for-v6.7-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: walkera0701 - use module_parport_driver macro to simplify the code
Input: synaptics-rmi4 - fix use after free in rmi_unregister_function()
dt-bindings: input: fsl,scu-key: Document wakeup-source
Input: cyttsp5 - add handling for vddio regulator
dt-bindings: input: cyttsp5: document vddio-supply
Input: tegra-kbc - use device_get_match_data()
Input: Annotate struct ff_device with __counted_by
Input: axp20x-pek - avoid needless newline removal
Input: mt - annotate struct input_mt with __counted_by
Input: leds - annotate struct input_leds with __counted_by
Input: evdev - annotate struct evdev_client with __counted_by
Input: synaptics-rmi4 - replace deprecated strncpy
Input: wm97xx-core - convert to platform remove callback returning void
Input: wm831x-ts - convert to platform remove callback returning void
Input: ti_am335x_tsc - convert to platform remove callback returning void
Input: sun4i-ts - convert to platform remove callback returning void
Input: stmpe-ts - convert to platform remove callback returning void
Input: pcap_ts - convert to platform remove callback returning void
Input: mc13783_ts - convert to platform remove callback returning void
Input: mainstone-wm97xx - convert to platform remove callback returning void
...
Pull watchdog updates from Wim Van Sebroeck:
- add support for Amlogic C3 and S4 SoCs
- add IT8613 ID
- add MSM8226 and MSM8974 compatibles
- other small fixes and improvements
* tag 'linux-watchdog-6.7-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
dt-bindings: watchdog: Add support for Amlogic C3 and S4 SoCs
watchdog: mlx-wdt: Parameter desctiption warning fix
watchdog: aspeed: Add support for aspeed,reset-mask DT property
dt-bindings: watchdog: aspeed-wdt: Add aspeed,reset-mask property
watchdog: apple: Deactivate on suspend
dt-bindings: watchdog: qcom-wdt: Add MSM8226 and MSM8974 compatibles
dt-bindings: watchdog: fsl-imx7ulp-wdt: Add 'fsl,ext-reset-output'
wdog: imx7ulp: Enable wdog int_en bit for watchdog any reset
drivers: watchdog: marvell_gti: Program the max_hw_heartbeat_ms
drivers: watchdog: marvell_gti: fix zero pretimeout handling
watchdog: marvell_gti: Replace of_platform.h with explicit includes
watchdog: imx_sc_wdt: continue if the wdog already enabled
watchdog: st_lpc: Use device_get_match_data()
watchdog: wdat_wdt: Add timeout value as a param in ping method
watchdog: gpio_wdt: Make use of device properties
sbsa_gwdt: Calculate timeout with 64-bit math
watchdog: ixp4xx: Make sure restart always works
watchdog: it87_wdt: add IT8613 ID
watchdog: marvell_gti_wdt: Fix error code in probe()
Watchdog: marvell_gti_wdt: Remove redundant dev_err_probe() for platform_get_irq()
...
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
Pull iommu updates from Joerg Roedel:
"Core changes:
- Make default-domains mandatory for all IOMMU drivers
- Remove group refcounting
- Add generic_single_device_group() helper and consolidate drivers
- Cleanup map/unmap ops
- Scaling improvements for the IOVA rcache depot
- Convert dart & iommufd to the new domain_alloc_paging()
ARM-SMMU:
- Device-tree binding update:
- Add qcom,sm7150-smmu-v2 for Adreno on SM7150 SoC
- SMMUv2:
- Support for Qualcomm SDM670 (MDSS) and SM7150 SoCs
- SMMUv3:
- Large refactoring of the context descriptor code to move the CD
table into the master, paving the way for '->set_dev_pasid()'
support on non-SVA domains
- Minor cleanups to the SVA code
Intel VT-d:
- Enable debugfs to dump domain attached to a pasid
- Remove an unnecessary inline function
AMD IOMMU:
- Initial patches for SVA support (not complete yet)
S390 IOMMU:
- DMA-API conversion and optimized IOTLB flushing
And some smaller fixes and improvements"
* tag 'iommu-updates-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (102 commits)
iommu/dart: Remove the force_bypass variable
iommu/dart: Call apple_dart_finalize_domain() as part of alloc_paging()
iommu/dart: Convert to domain_alloc_paging()
iommu/dart: Move the blocked domain support to a global static
iommu/dart: Use static global identity domains
iommufd: Convert to alloc_domain_paging()
iommu/vt-d: Use ops->blocked_domain
iommu/vt-d: Update the definition of the blocking domain
iommu: Move IOMMU_DOMAIN_BLOCKED global statics to ops->blocked_domain
Revert "iommu/vt-d: Remove unused function"
iommu/amd: Remove DMA_FQ type from domain allocation path
iommu: change iommu_map_sgtable to return signed values
iommu/virtio: Add __counted_by for struct viommu_request and use struct_size()
iommu/vt-d: debugfs: Support dumping a specified page table
iommu/vt-d: debugfs: Create/remove debugfs file per {device, pasid}
iommu/vt-d: debugfs: Dump entry pointing to huge page
iommu/vt-d: Remove unused function
iommu/arm-smmu-v3-sva: Remove bond refcount
iommu/arm-smmu-v3-sva: Remove unused iommu_sva handle
iommu/arm-smmu-v3: Rename cdcfg to cd_table
...
Pull more drm updates from Dave Airlie:
"Geert pointed out I missed the renesas reworks in my main pull, so
this pull contains the renesas next work for atomic conversion and DT
support.
It also contains a bunch of amdgpu and some small ssd13xx fixes.
renesas:
- atomic conversion
- DT support
ssd13xx:
- dt binding fix for ssd132x
- Initialize ssd130x crtc_state to NULL.
amdgpu:
- Fix RAS support check
- RAS fixes
- MES fixes
- SMU13 fixes
- Contiguous memory allocation fix
- BACO fixes
- GPU reset fixes
- Min power limit fixes
- GFX11 fixes
- USB4/TB hotplug fixes
- ARM regression fix
- GFX9.4.3 fixes
- KASAN/KCSAN stack size check fixes
- SR-IOV fixes
- SMU14 fixes
- PSP13 fixes
- Display blend fixes
- Flexible array size fixes
amdkfd:
- GPUVM fix
radeon:
- Flexible array size fixes"
* tag 'drm-next-2023-11-07' of git://anongit.freedesktop.org/drm/drm: (83 commits)
drm/amd/display: Enable fast update on blendTF change
drm/amd/display: Fix blend LUT programming
drm/amd/display: Program plane color setting correctly
drm/amdgpu: Query and report boot status
drm/amdgpu: Add psp v13 function to query boot status
drm/amd/swsmu: remove fw version check in sw_init.
drm/amd/swsmu: update smu v14_0_0 driver if and metrics table
drm/amdgpu: Add C2PMSG_109/126 reg field shift/masks
drm/amdgpu: Optimize the asic type fix code
drm/amdgpu: fix GRBM read timeout when do mes_self_test
drm/amdgpu: check recovery status of xgmi hive in ras_reset_error_count
drm/amd/pm: only check sriov vf flag once when creating hwmon sysfs
drm/amdgpu: Attach eviction fence on alloc
drm/amdkfd: Improve amdgpu_vm_handle_moved
drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml2
drm/amd/display: Avoid NULL dereference of timing generator
drm/amdkfd: Update cache info for GFX 9.4.3
drm/amdkfd: Populate cache info for GFX 9.4.3
drm/amdgpu: don't put MQDs in VRAM on ARM | ARM64
drm/amdgpu/smu13: drop compute workload workaround
...
Pull remoteproc updates from Bjorn Andersson:
"Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers"
* tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: st: Fix sometimes uninitialized ret in st_rproc_probe()
remoteproc: st: Use device_get_match_data()
remoteproc: zynqmp: Change tcm address translation method
remoteproc: mediatek: Refactor single core check and fix retrocompatibility
remoteproc: qcom: q6v5-mss: Remove PNoC clock from 8996 MSS
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Remove PNoC clock
dt-bindings: remoteproc: qcom,adsp: Remove AGGRE2 clock
remoteproc: qcom: pas: Add SM6375 MPSS
remoteproc: qcom: pas: Add SM6375 ADSP & CDSP
dt-bindings: remoteproc: qcom,sm6375-pas: Document remoteprocs
dt-bindings: remoteproc: pru: Add Interrupt property
remoteproc: qcom: pas: Add sc7180 adsp
dt-bindings: remoteproc: qcom: sc7180-pas: Add ADSP compatible
arm64: dts: mediatek: Update the node name of SCP rpmsg subnode
remoteproc: zynqmp: fix TCM carveouts in lockstep mode
remoteproc: mediatek: Refine ipi handler error message
remoteproc: mediatek: Report watchdog crash to all cores
remoteproc: mediatek: Handle MT8195 SCP core 1 watchdog timeout
remoteproc: mediatek: Setup MT8195 SCP core 1 SRAM offset
remoteproc: mediatek: Remove dependency of MT8195 SCP L2TCM power control on dual-core SCP
...
Pull media updates from Mauro Carvalho Chehab:
- the old V4L2 core videobuf kAPI was finally removed. All media
drivers should now be using VB2 kAPI
- new automotive driver: mgb4
- new platform video driver: npcm-video
- new sensor driver: mt9m114
- new TI driver used in conjunction with Cadence CSI2RX IP to bridge
TI-specific parts
- ir-rx51 was removed and the N900 DT binding was moved to the
pwm-ir-tx generic driver
- drop atomisp-specific ov5693, using the upstream driver instead
- the camss driver has gained RDI3 support for VFE 17x
- the atomisp driver now detects ISP2400 or ISP2401 at run time. No
need to set it up at build time anymore
- lots of driver fixes, cleanups and improvements
* tag 'media/v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
media: nuvoton: VIDEO_NPCM_VCD_ECE should depend on ARCH_NPCM
media: venus: Fix firmware path for resources
media: venus: hfi_cmds: Replace one-element array with flex-array member and use __counted_by
media: venus: hfi_parser: Add check to keep the number of codecs within range
media: venus: hfi: add checks to handle capabilities from firmware
media: venus: hfi: fix the check to handle session buffer requirement
media: venus: hfi: add checks to perform sanity on queue pointers
media: platform: cadence: select MIPI_DPHY dependency
media: MAINTAINERS: Fix path for J721E CSI2RX bindings
media: cec: meson: always include meson sub-directory in Makefile
media: videobuf2: Fix IS_ERR checking in vb2_dc_put_userptr()
media: platform: mtk-mdp3: fix uninitialized variable in mdp_path_config()
media: mediatek: vcodec: using encoder device to alloc/free encoder memory
media: imx-jpeg: notify source chagne event when the first picture parsed
media: cx231xx: Use EP5_BUF_SIZE macro
media: siano: Drop unnecessary error check for debugfs_create_dir/file()
media: mediatek: vcodec: Handle invalid encoder vsi
media: aspeed: Drop unnecessary error check for debugfs_create_file()
Documentation: media: buffer.rst: fix V4L2_BUF_FLAG_PREPARED
Documentation: media: gen-errors.rst: fix confusing ENOTTY description
...
Pull RTC updates from Alexandre Belloni:
"There is a new driver for the RTC of the Mstar SSD202D SoC. The
rtc7301 driver gains support for byte addresses to support the
USRobotics USR8200. Then we have many non user visible changes and
typo fixes.
Summary:
Subsytem:
- convert platform drivers to remove_new
- prevent modpost warnings for unremovable platform drivers
New driver:
- Mstar SSD202D
Drivers:
- brcmstb-waketimer: support level alarm_irq
- ep93xx: add DT support
- rtc7301: support byte-addressed IO"
* tag 'rtc-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
dt-bindings: rtc: Add Mstar SSD202D RTC
rtc: Add support for the SSD202D RTC
rtc: at91rm9200: annotate at91_rtc_remove with __exit again
dt-bindings: rtc: microcrystal,rv3032: Document wakeup-source property
dt-bindings: rtc: pcf8523: Convert to YAML
dt-bindings: rtc: mcp795: move to trivial-rtc
rtc: ep93xx: add DT support for Cirrus EP93xx
dt-bindings: rtc: Add Cirrus EP93xx
dt-bindings: rtc: pcf2123: convert to YAML
rtc: efi: fixed typo in efi_procfs()
rtc: omap: Use device_get_match_data()
rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
rtc: rtc7301: Support byte-addressed IO
rtc: rtc7301: Rewrite bindings in schema
rtc: sh: Convert to platform remove callback returning void
rtc: pxa: Convert to platform remove callback returning void
rtc: mv: Convert to platform remove callback returning void
rtc: imxdi: Convert to platform remove callback returning void
rtc: at91rm9200: Convert to platform remove callback returning void
rtc: pcap: Drop no-op remove function
...
Pull i2c updates from Wolfram Sang:
"I2C has largely driver updates for 6.7, i.e. feature additions (like
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions...
you name it.
The core got a memleak fix and better support for nested muxes"
* tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: s3c2410: make i2c_s3c_irq_nextbyte() void
i2c: qcom-geni: add ACPI device id for sc8180x
Documentation: i2c: add fault code for not supporting 10 bit addresses
i2c: sun6i-p2wi: Prevent potential division by zero
i2c: mux: demux-pinctrl: Convert to use sysfs_emit_at() API
i2c: i801: Use new helper acpi_use_parent_companion
ACPI: Add helper acpi_use_parent_companion
MAINTAINERS: add YAML file for i2c-demux-pinctrl
i2c: core: fix lockdep warning for sparsely nested adapter chain
i2c: axxia: eliminate kernel-doc warnings
dt-bindings: i2c: i2c-demux-pinctrl: Convert to json-schema
i2c: stm32f7: Use devm_clk_get_enabled()
i2c: stm32f4: Use devm_clk_get_enabled()
i2c: stm32f7: add description of atomic in struct stm32f7_i2c_dev
i2c: fix memleak in i2c_new_client_device()
i2c: exynos5: Calculate t_scl_l, t_scl_h according to i2c spec
i2c: i801: Simplify class-based client device instantiation
i2c: exynos5: add support for atomic transfers
i2c: at91-core: Use devm_clk_get_enabled()
eeprom: at24: add ST M24C64-D Additional Write lockable page support
...
Pull i3c updates from Alexandre Belloni:
"There are now more fixes because as stated in my previous pull
request, people now have access to actual hardware.
Core:
- handle IBI in the proper order
Drivers:
- cdns: fix status register access
- mipi-i3c-hci: many fixes now that the driver has been actually
tested
- svc: many IBI fixes, correct compatible string, fix hot join corner
cases"
* tag 'i3c/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (29 commits)
i3c: master: handle IBIs in order they came
i3c: master: mipi-i3c-hci: Fix a kernel panic for accessing DAT_data.
i3c: master: svc: fix compatibility string mismatch with binding doc
i3c: master: svc: fix random hot join failure since timeout error
i3c: master: svc: fix SDA keep low when polling IBIWON timeout happen
i3c: master: svc: fix check wrong status register in irq handler
i3c: master: svc: fix ibi may not return mandatory data byte
i3c: master: svc: fix wrong data return when IBI happen during start frame
i3c: master: svc: fix race condition in ibi work thread
i3c: Fix typo "Provisional ID" to "Provisioned ID"
i3c: Fix potential refcount leak in i3c_master_register_new_i3c_devs
i3c: mipi-i3c-hci: Resume controller after aborted transfer
i3c: mipi-i3c-hci: Resume controller explicitly
i3c: mipi-i3c-hci: Fix missing xfer->completion in hci_cmd_v1_daa()
i3c: mipi-i3c-hci: Do not unmap region not mapped for transfer
i3c: mipi-i3c-hci: Set number of SW enabled Ring Bundles earlier
i3c: mipi-i3c-hci: Fix race between bus cleanup and interrupt
i3c: mipi-i3c-hci: Set ring start request together with enable
i3c: mipi-i3c-hci: Remove BUG() when Ring Abort request times out
i3c: mipi-i3c-hci: Fix out of bounds access in hci_dma_irq_handler
...
Pull mtd updates from Miquel Raynal:
"The main set of changes is related to Uwe's work converting platform
remove callbacks to return void. Comes next (in number of changes)
Kees' additional structures annotations to improve the sanitizers. The
usual amount of cleanups apply.
About the more substancial contribution, one main function of the
partitions core could return an error which was not checked, this is
now fixed. On the bindings side, fixed partitions can now have a
compression property. Finally, an erroneous situation is now always
avoided in the MAP RAM driver.
CFI:
- A several years old byte swap has been fixed.
NAND:
- The subsystem has, as usual, seen a bit of cleanup being done this
cycle, typically return values of platform_get_irq() and
devm_kasprintf(). There is also a better ECC check in the Arasan
driver. This comes with smaller misc changes.
- In the SPI-NAND world there is now support for Foresee F35SQA002G,
Winbond W25N and XTX XT26 chips.
SPI NOR:
- For SPI NOR we cleaned the flash info entries in order to have them
slimmer and self explanatory. In order to make the entries as slim
as possible, we introduced sane default values so that the actual
flash entries don't need to specify them. We now use a flexible
macro to specify the flash ID instead of the previous INFOx()
macros that had hardcoded ID lengths.
Instead of:
{ "w25q512nwm", INFO(0xef8020, 0, 64 * 1024, 0)
OTP_INFO(256, 3, 0x1000, 0x1000) },
We now use:
.id = SNOR_ID(0xef, 0x80, 0x20),
.name = "w25q512nwm",
.otp = SNOR_OTP(256, 3, 0x1000, 0x1000),
- We also removed some flash entries: the very old Catalyst SPI
EEPROMs that were introduced once with the SPI-NOR subsystem, and a
Fujitsu MRAM. Both should use the at25 EEPROM driver. The latter
even has device tree bindings for the at25 driver.
- We made sure that the conversion didn't introduce any unwanted
changes by comparing the .rodata segment before and after the
conversion. The patches landed in linux-next immediately after
v6.6-rc2, we haven't seen any regressions yet.
- Apart of the autumn cleaning we introduced a new flash entry,
at25ff321a, and added block protection support for mt25qu512a"
* tag 'mtd/for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (91 commits)
mtd: cfi_cmdset_0001: Byte swap OTP info
mtd: rawnand: meson: check return value of devm_kasprintf()
mtd: rawnand: intel: check return value of devm_kasprintf()
mtd: rawnand: sh_flctl: Convert to module_platform_driver()
mtd: spi-nor: micron-st: use SFDP table for mt25qu512a
mtd: spi-nor: micron-st: enable lock/unlock for mt25qu512a
mtd: rawnand: Remove unused of_gpio.h inclusion
mtd: spinand: Add support for XTX XT26xxxDxxxxx
mtd: spinand: winbond: add support for serial NAND flash
mtd: rawnand: cadence: Annotate struct cdns_nand_chip with __counted_by
mtd: rawnand: Annotate struct mtk_nfc_nand_chip with __counted_by
mtd: spinand: add support for FORESEE F35SQA002G
mtd: rawnand: rockchip: Use struct_size()
mtd: rawnand: arasan: Include ECC syndrome along with in-band data while checking for ECC failure
mtd: Use device_get_match_data()
mtd: spi-nor: nxp-spifi: Convert to platform remove callback returning void
mtd: spi-nor: hisi-sfc: Convert to platform remove callback returning void
mtd: maps: sun_uflash: Convert to platform remove callback returning void
mtd: maps: sa1100-flash: Convert to platform remove callback returning void
mtd: maps: pxa2xx-flash: Convert to platform remove callback returning void
...
Pull pin control updates from Linus Walleij:
"No pin control core changes this time.
New drivers:
- Realtek RTD family pin control driver and RTD1619B, RTD1319D and
RTD1315E subdrivers
- Nuvoton NPCM8xx combined pin control and GPIO driver
- Amlogic T7 pin control driver
- Renesas RZ/G3S pin control driver
Improvements:
- A number of additional UART groups added to the Mediatek MT7981
driver
- MPM pin maps added for Qualcomm MSM8996, SM6115, SM6125 and SDM660
- Extra GPIO banks for the Sunxi H616
- MLSP I2C6 function support in Qualcomm MSM8226
- Some __counted_by() annotations for dynamic arrays
- Ongoing work to make remove() return void
- LSBC groups and functions in the Renesas R8A7778"
* tag 'pinctrl-v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (110 commits)
pinctrl: Use device_get_match_data()
dt-bindings: pinctrl: qcom,sa8775p-tlmm: add missing wakeup-parent
dt-bindings: pinctrl: nuvoton,npcm845: Add missing additionalProperties on gpio child nodes
dt-bindings: pinctrl: brcm: Ensure all child node properties are documented
pinctrl: renesas: rzn1: Convert to platform remove callback returning void
pinctrl: renesas: rzg2l: Add RZ/G3S support
dt-bindings: pinctrl: renesas: Document RZ/G3S SoC
pinctrl: renesas: rzg2l: Add support for different DS values on different groups
pinctrl: renesas: rzg2l: Move DS and OI to SoC-specific configuration
pinctrl: renesas: rzg2l: Adapt function number for RZ/G3S
pinctrl: renesas: rzg2l: Adapt for different SD/PWPR register offsets
pinctrl: renesas: rzg2l: Index all registers based on port offset
pinctrl: renesas: rzg2l: Add validation of GPIO pin in rzg2l_gpio_request()
pinctrl: renesas: r8a7778: Add LBSC pins, groups, and functions
pinctrl: intel: fetch community only when we need it
pinctrl: cherryview: reduce scope of PIN_CONFIG_BIAS_HIGH_IMPEDANCE case
pinctrl: cherryview: Convert to platform remove callback returning void
pinctrl: sprd-sc9860: Convert to platform remove callback returning void
pinctrl: qcom/msm: Convert to platform remove callback returning void
pinctrl: qcom/lpi: Convert to platform remove callback returning void
...
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
Pull tty and serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.7-rc1. Included
in here are:
- console/vgacon cleanups and removals from Arnd
- tty core and n_tty cleanups from Jiri
- lots of 8250 driver updates and cleanups
- sc16is7xx serial driver updates
- dt binding updates
- first set of port lock wrapers from Thomas for the printk fixes
coming in future releases
- other small serial and tty core cleanups and updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (193 commits)
serdev: Replace custom code with device_match_acpi_handle()
serdev: Simplify devm_serdev_device_open() function
serdev: Make use of device_set_node()
tty: n_gsm: add copyright Siemens Mobility GmbH
tty: n_gsm: fix race condition in status line change on dead connections
serial: core: Fix runtime PM handling for pending tx
vgacon: fix mips/sibyte build regression
dt-bindings: serial: drop unsupported samsung bindings
tty: serial: samsung: drop earlycon support for unsupported platforms
tty: 8250: Add note for PX-835
tty: 8250: Fix IS-200 PCI ID comment
tty: 8250: Add Brainboxes Oxford Semiconductor-based quirks
tty: 8250: Add support for Intashield IX cards
tty: 8250: Add support for additional Brainboxes PX cards
tty: 8250: Fix up PX-803/PX-857
tty: 8250: Fix port count of PX-257
tty: 8250: Add support for Intashield IS-100
tty: 8250: Add support for Brainboxes UP cards
tty: 8250: Add support for additional Brainboxes UC cards
tty: 8250: Remove UC-257 and UC-431
...
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
Pull crypto updates from Herbert Xu:
"API:
- Add virtual-address based lskcipher interface
- Optimise ahash/shash performance in light of costly indirect calls
- Remove ahash alignmask attribute
Algorithms:
- Improve AES/XTS performance of 6-way unrolling for ppc
- Remove some uses of obsolete algorithms (md4, md5, sha1)
- Add FIPS 202 SHA-3 support in pkcs1pad
- Add fast path for single-page messages in adiantum
- Remove zlib-deflate
Drivers:
- Add support for S4 in meson RNG driver
- Add STM32MP13x support in stm32
- Add hwrng interface support in qcom-rng
- Add support for deflate algorithm in hisilicon/zip"
* tag 'v6.7-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (283 commits)
crypto: adiantum - flush destination page before unmapping
crypto: testmgr - move pkcs1pad(rsa,sha3-*) to correct place
Documentation/module-signing.txt: bring up to date
module: enable automatic module signing with FIPS 202 SHA-3
crypto: asymmetric_keys - allow FIPS 202 SHA-3 signatures
crypto: rsa-pkcs1pad - Add FIPS 202 SHA-3 support
crypto: FIPS 202 SHA-3 register in hash info for IMA
x509: Add OIDs for FIPS 202 SHA-3 hash and signatures
crypto: ahash - optimize performance when wrapping shash
crypto: ahash - check for shash type instead of not ahash type
crypto: hash - move "ahash wrapping shash" functions to ahash.c
crypto: talitos - stop using crypto_ahash::init
crypto: chelsio - stop using crypto_ahash::init
crypto: ahash - improve file comment
crypto: ahash - remove struct ahash_request_priv
crypto: ahash - remove crypto_ahash_alignmask
crypto: gcm - stop using alignmask of ahash
crypto: chacha20poly1305 - stop using alignmask of ahash
crypto: ccm - stop using alignmask of ahash
net: ipv6: stop checking crypto_ahash_alignmask
...
Pull kvm updates from Paolo Bonzini:
"ARM:
- Generalized infrastructure for 'writable' ID registers, effectively
allowing userspace to opt-out of certain vCPU features for its
guest
- Optimization for vSGI injection, opportunistically compressing
MPIDR to vCPU mapping into a table
- Improvements to KVM's PMU emulation, allowing userspace to select
the number of PMCs available to a VM
- Guest support for memory operation instructions (FEAT_MOPS)
- Cleanups to handling feature flags in KVM_ARM_VCPU_INIT, squashing
bugs and getting rid of useless code
- Changes to the way the SMCCC filter is constructed, avoiding wasted
memory allocations when not in use
- Load the stage-2 MMU context at vcpu_load() for VHE systems,
reducing the overhead of errata mitigations
- Miscellaneous kernel and selftest fixes
LoongArch:
- New architecture for kvm.
The hardware uses the same model as x86, s390 and RISC-V, where
guest/host mode is orthogonal to supervisor/user mode. The
virtualization extensions are very similar to MIPS, therefore the
code also has some similarities but it's been cleaned up to avoid
some of the historical bogosities that are found in arch/mips. The
kernel emulates MMU, timer and CSR accesses, while interrupt
controllers are only emulated in userspace, at least for now.
RISC-V:
- Support for the Smstateen and Zicond extensions
- Support for virtualizing senvcfg
- Support for virtualized SBI debug console (DBCN)
S390:
- Nested page table management can be monitored through tracepoints
and statistics
x86:
- Fix incorrect handling of VMX posted interrupt descriptor in
KVM_SET_LAPIC, which could result in a dropped timer IRQ
- Avoid WARN on systems with Intel IPI virtualization
- Add CONFIG_KVM_MAX_NR_VCPUS, to allow supporting up to 4096 vCPUs
without forcing more common use cases to eat the extra memory
overhead.
- Add virtualization support for AMD SRSO mitigation (IBPB_BRTYPE and
SBPB, aka Selective Branch Predictor Barrier).
- Fix a bug where restoring a vCPU snapshot that was taken within 1
second of creating the original vCPU would cause KVM to try to
synchronize the vCPU's TSC and thus clobber the correct TSC being
set by userspace.
- Compute guest wall clock using a single TSC read to avoid
generating an inaccurate time, e.g. if the vCPU is preempted
between multiple TSC reads.
- "Virtualize" HWCR.TscFreqSel to make Linux guests happy, which
complain about a "Firmware Bug" if the bit isn't set for select
F/M/S combos. Likewise "virtualize" (ignore) MSR_AMD64_TW_CFG to
appease Windows Server 2022.
- Don't apply side effects to Hyper-V's synthetic timer on writes
from userspace to fix an issue where the auto-enable behavior can
trigger spurious interrupts, i.e. do auto-enabling only for guest
writes.
- Remove an unnecessary kick of all vCPUs when synchronizing the
dirty log without PML enabled.
- Advertise "support" for non-serializing FS/GS base MSR writes as
appropriate.
- Harden the fast page fault path to guard against encountering an
invalid root when walking SPTEs.
- Omit "struct kvm_vcpu_xen" entirely when CONFIG_KVM_XEN=n.
- Use the fast path directly from the timer callback when delivering
Xen timer events, instead of waiting for the next iteration of the
run loop. This was not done so far because previously proposed code
had races, but now care is taken to stop the hrtimer at critical
points such as restarting the timer or saving the timer information
for userspace.
- Follow the lead of upstream Xen and ignore the VCPU_SSHOTTMR_future
flag.
- Optimize injection of PMU interrupts that are simultaneous with
NMIs.
- Usual handful of fixes for typos and other warts.
x86 - MTRR/PAT fixes and optimizations:
- Clean up code that deals with honoring guest MTRRs when the VM has
non-coherent DMA and host MTRRs are ignored, i.e. EPT is enabled.
- Zap EPT entries when non-coherent DMA assignment stops/start to
prevent using stale entries with the wrong memtype.
- Don't ignore guest PAT for CR0.CD=1 && KVM_X86_QUIRK_CD_NW_CLEARED=y
This was done as a workaround for virtual machine BIOSes that did
not bother to clear CR0.CD (because ancient KVM/QEMU did not bother
to set it, in turn), and there's zero reason to extend the quirk to
also ignore guest PAT.
x86 - SEV fixes:
- Report KVM_EXIT_SHUTDOWN instead of EINVAL if KVM intercepts
SHUTDOWN while running an SEV-ES guest.
- Clean up the recognition of emulation failures on SEV guests, when
KVM would like to "skip" the instruction but it had already been
partially emulated. This makes it possible to drop a hack that
second guessed the (insufficient) information provided by the
emulator, and just do the right thing.
Documentation:
- Various updates and fixes, mostly for x86
- MTRR and PAT fixes and optimizations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (164 commits)
KVM: selftests: Avoid using forced target for generating arm64 headers
tools headers arm64: Fix references to top srcdir in Makefile
KVM: arm64: Add tracepoint for MMIO accesses where ISV==0
KVM: arm64: selftest: Perform ISB before reading PAR_EL1
KVM: arm64: selftest: Add the missing .guest_prepare()
KVM: arm64: Always invalidate TLB for stage-2 permission faults
KVM: x86: Service NMI requests after PMI requests in VM-Enter path
KVM: arm64: Handle AArch32 SPSR_{irq,abt,und,fiq} as RAZ/WI
KVM: arm64: Do not let a L1 hypervisor access the *32_EL2 sysregs
KVM: arm64: Refine _EL2 system register list that require trap reinjection
arm64: Add missing _EL2 encodings
arm64: Add missing _EL12 encodings
KVM: selftests: aarch64: vPMU test for validating user accesses
KVM: selftests: aarch64: vPMU register test for unimplemented counters
KVM: selftests: aarch64: vPMU register test for implemented counters
KVM: selftests: aarch64: Introduce vpmu_counter_access test
tools: Import arm_pmuv3.h
KVM: arm64: PMU: Allow userspace to limit PMCR_EL0.N for the guest
KVM: arm64: Sanitize PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR} before first run
KVM: arm64: Add {get,set}_user for PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}
...
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, megaraid_sas, lpfc, target, ibmvfc,
scsi_debug) plus the usual assorted minor fixes and updates.
The major change this time around is a prep patch for rethreading of
the driver reset handler API not to take a scsi_cmd structure which
starts to reduce various drivers' dependence on scsi_cmd in error
handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (132 commits)
scsi: ufs: core: Leave space for '\0' in utf8 desc string
scsi: ufs: core: Conversion to bool not necessary
scsi: ufs: core: Fix race between force complete and ISR
scsi: megaraid: Fix up debug message in megaraid_abort_and_reset()
scsi: aic79xx: Fix up NULL command in ahd_done()
scsi: message: fusion: Initialize return value in mptfc_bus_reset()
scsi: mpt3sas: Fix loop logic
scsi: snic: Remove useless code in snic_dr_clean_pending_req()
scsi: core: Add comment to target_destroy in scsi_host_template
scsi: core: Clean up scsi_dev_queue_ready()
scsi: pmcraid: Add missing scsi_device_put() in pmcraid_eh_target_reset_handler()
scsi: target: core: Fix kernel-doc comment
scsi: pmcraid: Fix kernel-doc comment
scsi: core: Handle depopulation and restoration in progress
scsi: ufs: core: Add support for parsing OPP
scsi: ufs: core: Add OPP support for scaling clocks and regulators
scsi: ufs: dt-bindings: common: Add OPP table
scsi: scsi_debug: Add param to control sdev's allow_restart
scsi: scsi_debug: Add debugfs interface to fail target reset
scsi: scsi_debug: Add new error injection type: Reset LUN failed
...
Pull LED updates from Lee Jones:
"Core Frameworks:
- Add support for a bunch more colours
New Drivers:
- Add support for Kinetic KTD2026/7 RGB/White LEDs
New Functionality:
- Add support for device to enter HW Controlled Mode to Turris Omnia
LEDs
- Add support for HW Gamma Correction to Turris Omnia LEDs
Fix-ups:
- Apply new __counted_by() annotation to several data structures
containing flexible arrays
- Rid the return value from Platform's .remove() operation
- Use *_cansleep() variants for instances were threads can sleep
- Improve the semantics when setting the brightness
- Generic clean-ups; code reduction, coding style, standard patterns
- Replace strncpy() with strscpy()
- Fix-up / add various documentation
- Re-author the GPIO associated Trigger to use trigger-sources
- Move to using standard APIs and helpers
- Improve error checking
- Stop using static GPIO bases
Bug Fixes:
- Fix Pointer to Enum casing warnings
- Do not pretend that I2C backed device supports SMBUS
- Ensure PWM LEDs are extinguished when disabled, rather than held in
a state
- Fix 'output may be truncated' warnings"
* tag 'leds-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (43 commits)
leds: lp5521: Add an error check in lp5521_post_init_device
leds: gpio: Update headers
leds: gpio: Remove unneeded assignment
leds: gpio: Move temporary variable for struct device to gpio_led_probe()
leds: gpio: Refactor code to use devm_gpiod_get_index_optional()
leds: gpio: Utilise PTR_ERR_OR_ZERO()
leds: gpio: Keep driver firmware interface agnostic
leds: core: Refactor led_update_brightness() to use standard pattern
leds: turris-omnia: Fix brightness setting and trigger activating
leds: sc27xx: Move mutex_init() down
leds: trigger: netdev: Move size check in set_device_name
leds: Add ktd202x driver
dt-bindings: leds: Add Kinetic KTD2026/2027 LED
leds: core: Add more colors from DT bindings to led_colors
dt-bindings: leds: Last color ID is now 14 (LED_COLOR_ID_LIME)
leds: tca6507: Don't use fixed GPIO base
leds: lp3952: Convert to use maple tree register cache
leds: lm392x: Convert to use maple tree register cache
leds: aw200xx: Convert to use maple tree register cache
leds: lm3601x: Convert to use maple tree register cache
...
